Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This kernel cycle was quite calm when it comes to pin control and
  there is really just one major change, and that is the introduction of
  devm_pinctrl_register() managed resources.

  Apart from that linear development, details below.

  Core changes:

   - Add the devm_pinctrl_register() API and switch all applicable
     drivers to use it, saving lots of lines of code all over the place.

  New drivers:

   - driver for the Broadcom NS2 SoC

   - subdriver for the PXA25x SoCs

   - subdriver for the AMLogic Meson GXBB SoC

  Driver improvements:

   - the Intel Baytrail driver now properly supports pin control

   - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
     callback in the GPIO portions

   - continued development and stabilization of several SH-PFC SoC
     subdrivers: r8a7795, r8a7790, r8a7794 etc"

* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
  Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
  pinctrl: meson: Fix eth_tx_en bit index
  pinctrl: tegra: avoid parked_reg and parked_bank
  pinctrl: tegra: Correctly check the supported configuration
  pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
  pinctrl: rockchip: fix pull setting error for rk3399
  pinctrl: stm32: Implement .pin_config_dbg_show()
  pinctrl: nomadik: hide nmk_gpio_get_mode when unused
  pinctrl: ns2: rename pinctrl_utils_dt_free_map
  pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
  pinctrl: at91: Make at91_gpio_template const
  pinctrl: baytrail: fix some error handling in debugfs
  pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
  pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
  pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
  pinctrl: nomadik: implement .get_direction()
  pinctrl: nomadik: use BIT() with offsets consequently
  pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
  pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
  pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
  ...

1 files changed, 180 insertions, 5 deletions

diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
index 8deb566ed4cd..ae9fab82a1b9 100644
--- a/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -358,7 +358,7 @@ static int stm32_pctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
 		ret = stm32_pctrl_dt_subnode_to_map(pctldev, np, map,
 				&reserved_maps, num_maps);
 		if (ret < 0) {
-			pinctrl_utils_dt_free_map(pctldev, *map, *num_maps);
+			pinctrl_utils_free_map(pctldev, *map, *num_maps);
 			return ret;
 		}
 	}
@@ -396,7 +396,7 @@ static int stm32_pctrl_get_group_pins(struct pinctrl_dev *pctldev,
 
 static const struct pinctrl_ops stm32_pctrl_ops = {
 	.dt_node_to_map		= stm32_pctrl_dt_node_to_map,
-	.dt_free_map		= pinctrl_utils_dt_free_map,
+	.dt_free_map		= pinctrl_utils_free_map,
 	.get_groups_count	= stm32_pctrl_get_groups_count,
 	.get_group_name		= stm32_pctrl_get_group_name,
 	.get_group_pins		= stm32_pctrl_get_group_pins,
@@ -454,6 +454,29 @@ static void stm32_pmx_set_mode(struct stm32_gpio_bank *bank,
 	clk_disable(bank->clk);
 }
 
+static void stm32_pmx_get_mode(struct stm32_gpio_bank *bank,
+		int pin, u32 *mode, u32 *alt)
+{
+	u32 val;
+	int alt_shift = (pin % 8) * 4;
+	int alt_offset = STM32_GPIO_AFRL + (pin / 8) * 4;
+	unsigned long flags;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+
+	val = readl_relaxed(bank->base + alt_offset);
+	val &= GENMASK(alt_shift + 3, alt_shift);
+	*alt = val >> alt_shift;
+
+	val = readl_relaxed(bank->base + STM32_GPIO_MODER);
+	val &= GENMASK(pin * 2 + 1, pin * 2);
+	*mode = val >> (pin * 2);
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+}
+
 static int stm32_pmx_set_mux(struct pinctrl_dev *pctldev,
 			    unsigned function,
 			    unsigned group)
@@ -525,6 +548,24 @@ static void stm32_pconf_set_driving(struct stm32_gpio_bank *bank,
 	clk_disable(bank->clk);
 }
 
+static u32 stm32_pconf_get_driving(struct stm32_gpio_bank *bank,
+	unsigned int offset)
+{
+	unsigned long flags;
+	u32 val;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+
+	val = readl_relaxed(bank->base + STM32_GPIO_TYPER);
+	val &= BIT(offset);
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+
+	return (val >> offset);
+}
+
 static void stm32_pconf_set_speed(struct stm32_gpio_bank *bank,
 	unsigned offset, u32 speed)
 {
@@ -543,6 +584,24 @@ static void stm32_pconf_set_speed(struct stm32_gpio_bank *bank,
 	clk_disable(bank->clk);
 }
 
+static u32 stm32_pconf_get_speed(struct stm32_gpio_bank *bank,
+	unsigned int offset)
+{
+	unsigned long flags;
+	u32 val;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+
+	val = readl_relaxed(bank->base + STM32_GPIO_SPEEDR);
+	val &= GENMASK(offset * 2 + 1, offset * 2);
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+
+	return (val >> (offset * 2));
+}
+
 static void stm32_pconf_set_bias(struct stm32_gpio_bank *bank,
 	unsigned offset, u32 bias)
 {
@@ -561,6 +620,57 @@ static void stm32_pconf_set_bias(struct stm32_gpio_bank *bank,
 	clk_disable(bank->clk);
 }
 
+static u32 stm32_pconf_get_bias(struct stm32_gpio_bank *bank,
+	unsigned int offset)
+{
+	unsigned long flags;
+	u32 val;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+
+	val = readl_relaxed(bank->base + STM32_GPIO_PUPDR);
+	val &= GENMASK(offset * 2 + 1, offset * 2);
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+
+	return (val >> (offset * 2));
+}
+
+static bool stm32_pconf_input_get(struct stm32_gpio_bank *bank,
+	unsigned int offset)
+{
+	unsigned long flags;
+	u32 val;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+
+	val = !!(readl_relaxed(bank->base + STM32_GPIO_IDR) & BIT(offset));
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+
+	return val;
+}
+
+static bool stm32_pconf_output_get(struct stm32_gpio_bank *bank,
+	unsigned int offset)
+{
+	unsigned long flags;
+	u32 val;
+
+	clk_enable(bank->clk);
+	spin_lock_irqsave(&bank->lock, flags);
+	val = !!(readl_relaxed(bank->base + STM32_GPIO_ODR) & BIT(offset));
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+	clk_disable(bank->clk);
+
+	return val;
+}
+
 static int stm32_pconf_parse_conf(struct pinctrl_dev *pctldev,
 		unsigned int pin, enum pin_config_param param,
 		enum pin_config_param arg)
@@ -634,9 +744,73 @@ static int stm32_pconf_group_set(struct pinctrl_dev *pctldev, unsigned group,
 	return 0;
 }
 
+static void stm32_pconf_dbg_show(struct pinctrl_dev *pctldev,
+				 struct seq_file *s,
+				 unsigned int pin)
+{
+	struct pinctrl_gpio_range *range;
+	struct stm32_gpio_bank *bank;
+	int offset;
+	u32 mode, alt, drive, speed, bias;
+	static const char * const modes[] = {
+			"input", "output", "alternate", "analog" };
+	static const char * const speeds[] = {
+			"low", "medium", "high", "very high" };
+	static const char * const biasing[] = {
+			"floating", "pull up", "pull down", "" };
+	bool val;
+
+	range = pinctrl_find_gpio_range_from_pin_nolock(pctldev, pin);
+	bank = gpio_range_to_bank(range);
+	offset = stm32_gpio_pin(pin);
+
+	stm32_pmx_get_mode(bank, offset, &mode, &alt);
+	bias = stm32_pconf_get_bias(bank, offset);
+
+	seq_printf(s, "%s ", modes[mode]);
+
+	switch (mode) {
+	/* input */
+	case 0:
+		val = stm32_pconf_input_get(bank, offset);
+		seq_printf(s, "- %s - %s",
+			   val ? "high" : "low",
+			   biasing[bias]);
+		break;
+
+	/* output */
+	case 1:
+		drive = stm32_pconf_get_driving(bank, offset);
+		speed = stm32_pconf_get_speed(bank, offset);
+		val = stm32_pconf_output_get(bank, offset);
+		seq_printf(s, "- %s - %s - %s - %s %s",
+			   val ? "high" : "low",
+			   drive ? "open drain" : "push pull",
+			   biasing[bias],
+			   speeds[speed], "speed");
+		break;
+
+	/* alternate */
+	case 2:
+		drive = stm32_pconf_get_driving(bank, offset);
+		speed = stm32_pconf_get_speed(bank, offset);
+		seq_printf(s, "%d - %s - %s - %s %s", alt,
+			   drive ? "open drain" : "push pull",
+			   biasing[bias],
+			   speeds[speed], "speed");
+		break;
+
+	/* analog */
+	case 3:
+		break;
+	}
+}
+
+
 static const struct pinconf_ops stm32_pconf_ops = {
 	.pin_config_group_get	= stm32_pconf_group_get,
 	.pin_config_group_set	= stm32_pconf_group_set,
+	.pin_config_dbg_show	= stm32_pconf_dbg_show,
 };
 
 static int stm32_gpiolib_register_bank(struct stm32_pinctrl *pctl,
@@ -813,10 +987,11 @@ int stm32_pctl_probe(struct platform_device *pdev)
 	pctl->pctl_desc.pmxops = &stm32_pmx_ops;
 	pctl->dev = &pdev->dev;
 
-	pctl->pctl_dev = pinctrl_register(&pctl->pctl_desc, &pdev->dev, pctl);
-	if (!pctl->pctl_dev) {
+	pctl->pctl_dev = devm_pinctrl_register(&pdev->dev, &pctl->pctl_desc,
+					       pctl);
+	if (IS_ERR(pctl->pctl_dev)) {
 		dev_err(&pdev->dev, "Failed pinctrl registration\n");
-		return -EINVAL;
+		return PTR_ERR(pctl->pctl_dev);
 	}
 
 	for (i = 0; i < pctl->nbanks; i++)