Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 75 insertions, 0 deletions

diff --git a/drivers/message/i2o/Kconfig b/drivers/message/i2o/Kconfig
new file mode 100644
index 000000000000..8d132b0d6b12
--- /dev/null
+++ b/drivers/message/i2o/Kconfig
@@ -0,0 +1,75 @@
+
+menu "I2O device support"
+
+config I2O
+	tristate "I2O support"
+	depends on PCI
+	---help---
+	  The Intelligent Input/Output (I2O) architecture allows hardware
+	  drivers to be split into two parts: an operating system specific
+	  module called the OSM and an hardware specific module called the
+	  HDM. The OSM can talk to a whole range of HDM's, and ideally the
+	  HDM's are not OS dependent. This allows for the same HDM driver to
+	  be used under different operating systems if the relevant OSM is in
+	  place. In order for this to work, you need to have an I2O interface
+	  adapter card in your computer. This card contains a special I/O
+	  processor (IOP), thus allowing high speeds since the CPU does not
+	  have to deal with I/O.
+
+	  If you say Y here, you will get a choice of interface adapter
+	  drivers and OSM's with the following questions.
+
+	  To compile this support as a module, choose M here: the
+	  modules will be called i2o_core.
+
+	  If unsure, say N.
+
+config I2O_CONFIG
+	tristate "I2O Configuration support"
+	depends on PCI && I2O
+	help
+	  Say Y for support of the configuration interface for the I2O adapters.
+	  If you have a RAID controller from Adaptec and you want to use the
+	  raidutils to manage your RAID array, you have to say Y here.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_config.
+
+config I2O_BLOCK
+	tristate "I2O Block OSM"
+	depends on I2O
+	help
+	  Include support for the I2O Block OSM. The Block OSM presents disk
+	  and other structured block devices to the operating system. If you
+	  are using an RAID controller, you could access the array only by
+	  the Block OSM driver. But it is possible to access the single disks
+	  by the SCSI OSM driver, for example to monitor the disks.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_block.
+
+config I2O_SCSI
+	tristate "I2O SCSI OSM"
+	depends on I2O && SCSI
+	help
+	  Allows direct SCSI access to SCSI devices on a SCSI or FibreChannel
+	  I2O controller. You can use both the SCSI and Block OSM together if
+	  you wish. To access a RAID array, you must use the Block OSM driver.
+	  But you could use the SCSI OSM driver to monitor the single disks.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_scsi.
+
+config I2O_PROC
+	tristate "I2O /proc support"
+	depends on I2O
+	help
+	  If you say Y here and to "/proc file system support", you will be
+	  able to read I2O related information from the virtual directory
+	  /proc/i2o.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_proc.
+
+endmenu
+