CRIS v32: remove old GPIO and LEDs code

Since we now have a gpiolib driver, remove this code:

The gpio-etraxfs driver (along with things like gpio-keys-polled for
polling support) replaces the GIO driver implementations in mach-a3 and
mach-fs.  The various generic external chip drivers replace the "virtual
gpio" parts.

The generic gpio-leds driver replaces the LED handling.

Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

1 files changed, 0 insertions, 149 deletions

diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index c5cbd2aac60e..2735eb7671a5 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -149,155 +149,6 @@ config ETRAX_NANDBOOT
 	  Say Y if your boot code, kernel and root file system is in
 	  NAND flash. Say N if they are in NOR flash.
 
-config ETRAX_GPIO
-	bool "GPIO support"
-	depends on ETRAX_ARCH_V32
-	---help---
-	  Enables the ETRAX general port device (major 120, minors 0-4).
-	  You can use this driver to access the general port bits. It supports
-	  these ioctl's:
-	  #include <linux/etraxgpio.h>
-	  fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
-	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
-	  ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
-	  err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val);
-	  Remember that you need to setup the port directions appropriately in
-	  the General configuration.
-
-config ETRAX_VIRTUAL_GPIO
-	bool "Virtual GPIO support"
-	depends on ETRAX_GPIO
-	help
-	  Enables the virtual Etrax general port device (major 120, minor 6).
-	  It uses an I/O expander for the I2C-bus.
-
-config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN
-	int "Virtual GPIO interrupt pin on PA pin"
-	range 0 7
-	depends on ETRAX_VIRTUAL_GPIO
-	help
-	  The pin to use on PA for virtual gpio interrupt.
-
-config ETRAX_PA_CHANGEABLE_DIR
-	hex "PA user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PA that a
-	  user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PA_CHANGEABLE_BITS
-	hex "PA user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PA
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PB_CHANGEABLE_DIR
-	hex "PB user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PB
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PB_CHANGEABLE_BITS
-	hex "PB user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PB
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PC_CHANGEABLE_DIR
-	hex "PC user changeable dir mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PC
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PC_CHANGEABLE_BITS
-	hex "PC user changeable bits mask"
-	depends on ETRAX_GPIO
-	default "0x00000" if ETRAXFS
-	default "0x00000000" if !ETRAXFS
-	help
-	  This is a bitmask with information of what bits in PC
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PD_CHANGEABLE_DIR
-	hex "PD user changeable dir mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask with information of what bits in PD
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PD_CHANGEABLE_BITS
-	hex "PD user changeable bits mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PD
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PE_CHANGEABLE_DIR
-	hex "PE user changeable dir mask"
-	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PE
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PE_CHANGEABLE_BITS
-	hex "PE user changeable bits mask"
- 	depends on ETRAX_GPIO && ETRAXFS
-	default "0x00000"
-	help
-	  This is a bitmask (18 bits) with information of what bits in PE
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
-config ETRAX_PV_CHANGEABLE_DIR
-	hex "PV user changeable dir mask"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0x0000"
-	help
-	  This is a bitmask (16 bits) with information of what bits in PV
-	  that a user can change direction on using ioctl's.
-	  Bit set = changeable.
-	  You probably want 0x0000 here, but it depends on your hardware.
-
-config ETRAX_PV_CHANGEABLE_BITS
-	hex "PV user changeable bits mask"
-	depends on ETRAX_VIRTUAL_GPIO
-	default "0x0000"
-	help
-	  This is a bitmask (16 bits) with information of what bits in PV
-	  that a user can change the value on using ioctl's.
-	  Bit set = changeable.
-
 config ETRAX_CARDBUS
         bool "Cardbus support"
         depends on ETRAX_ARCH_V32