Merge tag 'qcom-dts-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm Device Tree Changes for v4.13

* Fix IPQ4019 i2c0 node
* Add GSBI7 on IPQ8064
* Add misc APQ8060 devices
* Fixup USB related devices on APQ8064 and MSM8974

* tag 'qcom-dts-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: add core I2C devices to the APQ8060 Dragonboard
  ARM: dts: add GSBI8 defines to the MSM8660 family
  ARM: dts: Qualcomm APQ8060 DragonBoard ALS sensor
  ARM: dts: add XOADC and IIO HWMON to MSM8660/APQ8060
  ARM: dts: qcom: ipq4019: fix i2c_0 node
  ARM: dts: qcom: add gsbi7 serial to ipq8064 SoC device tree
  ARM: dts: qcom-apq8064: Collapse usb support into one node
  ARM: dts: qcom-msm8974: Add HS usb node and OTG detection mechanisms
  ARM: dts: qcom: add charger otg regulator
  ARM: dts: qcom: Remove s4/5vs1,2 from RPM pm8941 control

Signed-off-by: Olof Johansson <olof@lixom.net>

14 files changed, 512 insertions, 183 deletions

diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 2da1413f5720..9d725f983282 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -23,6 +23,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include "qcom-msm8660.dtsi"
 
 / {
@@ -83,6 +84,25 @@
 		};
 	};
 
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* GPIO34 has interrupt 225 on the PM8058 */
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058 225 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&xoadc 0x00 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+
 	soc {
 		pinctrl@800000 {
 			/* eMMMC pins, all 8 data lines connected */
@@ -160,6 +180,19 @@
 				};
 			};
 
+			dragon_gsbi8_i2c_pins: gsbi8_i2c {
+				mux {
+					pins = "gpio64", "gpio65";
+					function = "gsbi8";
+				};
+				pinconf {
+					pins = "gpio64", "gpio65";
+					drive-strength = <16>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
 			dragon_gsbi12_i2c_pins: gsbi12_i2c {
 				mux {
 					pins = "gpio115", "gpio116";
@@ -317,6 +350,24 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
+					dragon_cm3605_gpios: cm3605-gpios {
+						/* Pin 34 connected to the proxy IRQ */
+						pinconf_gpio34 {
+							pins = "gpio34";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+						/* Pin 35 connected to ASET */
+						pinconf_gpio35 {
+							pins = "gpio35";
+							function = "normal";
+							output-high;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
 					dragon_veth_gpios: veth-gpios {
 						pinconf {
 							pins = "gpio40";
@@ -327,6 +378,47 @@
 					};
 				};
 
+				mpps@50 {
+					dragon_cm3605_mpps: cm3605-mpps {
+						pinconf {
+							pins = "mpp5";
+							function = "analog";
+							input-enable;
+							bias-high-impedance;
+							/* Let's use channel 5 */
+							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+				};
+
+				xoadc@197 {
+					/* Reference voltage 2.2 V */
+					xoadc-ref-supply = <&pm8058_l18>;
+
+					/* Board-specific channels */
+					mpp5@05 {
+						/* Connected to AOUT of ALS sensor */
+						reg = <0x00 0x05>;
+					};
+					mpp6@06 {
+						/* Connected to test point TP43 */
+						reg = <0x00 0x06>;
+					};
+					mpp7@07 {
+						/* Connected to battery thermistor */
+						reg = <0x00 0x07>;
+					};
+					mpp8@08 {
+						/* Connected to battery ID detector */
+						reg = <0x00 0x08>;
+					};
+					mpp9@09 {
+						/* Connected to XO thermistor */
+						reg = <0x00 0x09>;
+					};
+				};
+
 				led@48 {
 					/*
 					 * The keypad LED @0x48 is routed to
@@ -340,6 +432,7 @@
 					reg = <0x48>;
 					label = "pm8058:infrared:proximitysensor";
 					default-state = "off";
+					linux,default-trigger = "cm3605";
 				};
 				led@131 {
 					compatible = "qcom,pm8058-led";
@@ -368,6 +461,42 @@
 			};
 		};
 
+		gsbi@19800000 {
+			status = "ok";
+			qcom,mode = <GSBI_PROT_I2C>;
+
+			i2c@19880000 {
+				status = "ok";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+
+				eeprom@52 {
+					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					vcc-supply = <&pm8058_s3>;
+					pagesize = <64>;
+				};
+				wm8903: wm8903@1a {
+					/* This Woolfson Micro device has an unrouted interrupt line */
+					compatible = "wlf,wm8903";
+					reg = <0x1a>;
+
+					AVDD-supply = <&pm8058_l16>;
+					CPVDD-supply = <&pm8058_l16>;
+					DBVDD-supply = <&pm8058_s3>;
+					DCVDD-supply = <&pm8058_l0>;
+
+					gpio-controller;
+					#gpio-cells = <2>;
+
+					micdet-cfg = <0>;
+					micdet-delay = <100>;
+					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+				};
+			};
+		};
+
 		gsbi@19c00000 {
 			status = "ok";
 			qcom,mode = <GSBI_PROT_I2C_UART>;
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index 8f5de029bca9..f245064f320e 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -320,43 +320,37 @@
 		};
 
 		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			dr_mode		= "peripheral";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "peripheral";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		usb@12520000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		usb@12530000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index e39440a86739..3483a66e44c1 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -321,21 +321,15 @@
 		};
 
 		/* OTG */
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-			dr_mode		= "otg";
-		};
-
-		gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
 		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		amba {
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index 35f1d46edded..5b151e425530 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -150,42 +150,37 @@
 		};
 
 		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "ok";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "ok";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		/* on board fixed 3.3v supply */
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index 881ce707311a..053b5bdd7808 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -244,42 +244,37 @@
 		};
 
 		/* OTG */
-		usb1_phy: phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		usb3_phy: phy@12520000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		usb4_phy: phy@12530000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l23>;
-		};
-
-		gadget1: gadget@12500000 {
-			status = "okay";
-		};
-
-		/* OTG */
-		usb1: usb@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
-		usb3: usb@12520000 {
+		usb@12520000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
-		usb4: usb@12530000 {
+		usb@12530000 {
 			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
 		};
 
 		pci@1b500000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
index a34ba3555454..88a9aff41e2f 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
@@ -349,15 +349,15 @@
 			};
 		};
 
-		phy@12500000 {
-			status		= "okay";
-			vddcx-supply	= <&pm8921_s3>;
-			v3p3-supply	= <&pm8921_l3>;
-			v1p8-supply	= <&pm8921_l4>;
-		};
-
-		gadget@12500000 {
+		usb@12500000 {
 			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
 		};
 
 		gsbi@1a200000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 14a6f5ed02de..f3db185a6809 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -197,7 +197,7 @@
 			clock-frequency = <27000000>;
 		};
 
-		sleep_clk {
+		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
@@ -884,81 +884,97 @@
 			};
 		};
 
-		usb1_phy: phy@12500000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-
-			clocks		= <&gcc USB_HS1_XCVR_CLK>,
-					  <&gcc USB_HS1_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS1_RESET>;
-			reset-names	= "link";
-		};
-
-		usb3_phy: phy@12520000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS3_XCVR_CLK>,
-					  <&gcc USB_HS3_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS3_RESET>;
-			reset-names	= "link";
-		};
-
-		usb4_phy: phy@12530000 {
-			compatible	= "qcom,usb-otg-ci";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			dr_mode		= "host";
-
-			clocks		= <&gcc USB_HS4_XCVR_CLK>,
-					  <&gcc USB_HS4_H_CLK>;
-			clock-names	= "core", "iface";
-
-			resets		= <&gcc USB_HS4_RESET>;
-			reset-names	= "link";
-		};
-
-		gadget1: gadget@12500000 {
-			compatible	= "qcom,ci-hdrc";
-			reg		= <0x12500000 0x400>;
-			status		= "disabled";
-			dr_mode		= "peripheral";
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			usb-phy		= <&usb1_phy>;
-		};
-
 		usb1: usb@12500000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12500000 0x400>;
-			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb1_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb3: usb@12520000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12520000 0x400>;
-			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb3_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12520000 0x200>,
+			      <0x12520200 0x200>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS3_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs3_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs3_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb3 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		usb4: usb@12530000 {
-			compatible	= "qcom,ehci-host";
-			reg		= <0x12530000 0x400>;
-			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
-			status		= "disabled";
-			usb-phy		= <&usb4_phy>;
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12530000 0x200>,
+			      <0x12530200 0x200>;
+			interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS4_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs4_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs4_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb4 0>;
+					reset-names = "por";
+				};
+			};
 		};
 
 		sata_phy0: phy@1b400000 {
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index ad51df27dfb7..32f3b81f609c 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -44,6 +44,26 @@
 			vqmmc-supply = <&pm8941_l13>;
 		};
 
+		usb@f9a55000 {
+			status = "ok";
+			phys = <&usb_hs2_phy>;
+			phy-select = <&tcsr 0xb000 1>;
+			extcon = <&smbb>, <&usb_id>;
+			vbus-supply = <&chg_otg>;
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ulpi {
+				phy@b {
+					status = "ok";
+					v3p3-supply = <&pm8941_l24>;
+					v1p8-supply = <&pm8941_l6>;
+					extcon = <&smbb>;
+					qcom,init-seq = /bits/ 8 <0x1 0x63>;
+				};
+			};
+		};
+
 
 		pinctrl@fd510000 {
 			i2c11_pins: i2c11 {
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index b7a24af8f47b..4b7d97275c62 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -154,10 +154,10 @@
 
 		i2c_0: i2c@78b7000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
-			reg = <0x78b7000 0x6000>;
+			reg = <0x78b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
 			clock-names = "iface", "core";
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 76f4e8921d58..f1fbffe59b93 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -284,6 +284,29 @@
 			};
 		};
 
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <0 158 0x0>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
 		sata_phy: sata-phy@1b400000 {
 			compatible = "qcom,ipq806x-sata-phy";
 			reg = <0x1b400000 0x200>;
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index 747669a62aa8..1b5d31b33b5e 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -63,6 +63,22 @@
 		};
 	};
 
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&xoadc 0x00 0x01>, /* Battery */
+			    <&xoadc 0x00 0x02>, /* DC in (charger) */
+			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
+			    <&xoadc 0x00 0x0b>, /* Die temperature */
+			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			    <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -107,6 +123,31 @@
 			reg = <0x900000 0x4000>;
 		};
 
+
+		gsbi8: gsbi@19800000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x19800000 0x100>;
+			clocks = <&gcc GSBI8_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi8_i2c: i2c@19880000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x19880000 0x1000>;
+				interrupts = <GIC_SPI 161 IRQ_TYPE_NONE>;
+				clocks = <&gcc GSBI8_QUP_CLK>, <&gcc GSBI8_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		gsbi12: gsbi@19c00000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <12>;
@@ -267,6 +308,49 @@
 					row-hold = <91500>;
 				};
 
+				xoadc: xoadc@197 {
+					compatible = "qcom,pm8058-adc";
+					reg = <0x197>;
+					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+					#io-channel-cells = <2>;
+
+					vcoin: adc-channel@00 {
+						reg = <0x00 0x00>;
+					};
+					vbat: adc-channel@01 {
+						reg = <0x00 0x01>;
+					};
+					dcin: adc-channel@02 {
+						reg = <0x00 0x02>;
+					};
+					ichg: adc-channel@03 {
+						reg = <0x00 0x03>;
+					};
+					vph_pwr: adc-channel@04 {
+						reg = <0x00 0x04>;
+					};
+					usb_vbus: adc-channel@0a {
+						reg = <0x00 0x0a>;
+					};
+					die_temp: adc-channel@0b {
+						reg = <0x00 0x0b>;
+					};
+					ref_625mv: adc-channel@0c {
+						reg = <0x00 0x0c>;
+					};
+					ref_1250mv: adc-channel@0d {
+						reg = <0x00 0x0d>;
+					};
+					ref_325mv: adc-channel@0e {
+						reg = <0x00 0x0e>;
+					};
+					ref_muxoff: adc-channel@0f {
+						reg = <0x00 0x0f>;
+					};
+				};
+
 				rtc@1e8 {
 					compatible = "qcom,pm8058-rtc";
 					reg = <0x1e8>;
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index e7c1577d56f4..50966378f9e4 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -92,7 +92,6 @@
 					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
 					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
 					vdd_l21-supply = <&vreg_boost>;
-					vin_5vs-supply = <&pm8941_5v>;
 
 					s1 {
 						regulator-min-microvolt = <1300000>;
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 307bf6a647b3..c5ee68a3f7f5 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -3,6 +3,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
 #include <dt-bindings/gpio/gpio.h>
 #include "skeleton.dtsi"
 
@@ -551,6 +552,11 @@
 			reg = <0xfc400000 0x4000>;
 		};
 
+		tcsr: syscon@fd4a0000 {
+			compatible = "syscon";
+			reg = <0xfd4a0000 0x10000>;
+		};
+
 		tcsr_mutex_block: syscon@fd484000 {
 			compatible = "syscon";
 			reg = <0xfd484000 0x2000>;
@@ -620,6 +626,50 @@
 			status = "disabled";
 		};
 
+		otg: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy@a {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+
+				usb_hs2_phy: phy@b {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2B_PHY_BCR>, <&otg 1>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+			};
+		};
+
 		rng@f9bff000 {
 			compatible = "qcom,prng";
 			reg = <0xf9bff000 0x200>;
@@ -1021,7 +1071,6 @@
 					pm8941_s1: s1 {};
 					pm8941_s2: s2 {};
 					pm8941_s3: s3 {};
-					pm8941_5v: s4 {};
 
 					pm8941_l1: l1 {};
 					pm8941_l2: l2 {};
@@ -1051,9 +1100,6 @@
 					pm8941_lvs1: lvs1 {};
 					pm8941_lvs2: lvs2 {};
 					pm8941_lvs3: lvs3 {};
-
-					pm8941_5vs1: 5vs1 {};
-					pm8941_5vs2: 5vs2 {};
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index f8eb5e31c920..3fc9f34f45bb 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -26,7 +26,14 @@
 			bias-pull-up;
 		};
 
-		charger@1000 {
+		usb_id: misc@900 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x900>;
+			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_id";
+		};
+
+		smbb: charger@1000 {
 			compatible = "qcom,pm8941-charger";
 			reg = <0x1000>;
 			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
@@ -45,6 +52,10 @@
 					  "chg-gone",
 					  "usb-valid",
 					  "dc-valid";
+
+			usb-otg-in-supply = <&pm8941_5vs1>;
+
+			chg_otg: otg-vbus { };
 		};
 
 		pm8941_gpios: gpios@c000 {
@@ -171,5 +182,28 @@
 
 			status = "disabled";
 		};
+
+		regulators {
+			compatible = "qcom,pm8941-regulators";
+			interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
+			interrupt-names = "ocp-5vs1", "ocp-5vs2";
+			vin_5vs-supply = <&pm8941_5v>;
+
+			pm8941_5v: s4 {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-enable-ramp-delay = <500>;
+			};
+
+			pm8941_5vs1: 5vs1 {
+				regulator-enable-ramp-delay = <1000>;
+				regulator-pull-down;
+				regulator-over-current-protection;
+				qcom,ocp-max-retries = <10>;
+				qcom,ocp-retry-delay = <30>;
+				qcom,vs-soft-start-strength = <0>;
+				regulator-initial-mode = <1>;
+			};
+		};
 	};
 };