Merge tag 'nand/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next

MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()

NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
  - Populate the public nsteps field
  - Use the public nsteps field
* ECC BCH:
  - Populate the public nsteps field
  - Use the public nsteps field

Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
  - Skip bad blocks when searching for the BBT in NAND

Raw NAND controller drivers:
* Qcom:
  - Convert bindings to YAML
  - Use dma_mapping_error() for error check
  - Add missing nand_cleanup() in error path
  - Return actual error code instead of -ENODEV
  - Update last code word register
  - Add helper to configure location register
  - Rename parameter name in macro
  - Add helper to check last code word
  - Convert nandc to chip in Read/Write helper
  - Update register macro name for 0x2c offset
* GPMI:
  - Fix a double free in gpmi_nand_init
* Rockchip:
  - Use flexible-array member instead of zero-length array
* Atmel:
  - Update ecc_stats.corrected counter
* MXC:
  - Remove unneeded of_match_ptr()
* R852:
  - replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
  - Move to polling in pio mode on oops write
  - Read/write oob during EDU transfer
  - Fix OOB R/W with Hamming ECC
* FSMC:
  - Fix error code in fsmc_nand_probe()
* OMAP:
  - Use ECC information from the generic structures

SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()

SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG

3 files changed, 203 insertions, 142 deletions

diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index d0e422f4b3e0..678b39952502 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -143,6 +143,13 @@ patternProperties:
           Ready/Busy pins. Active state refers to the NAND ready state and
           should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted.
 
+      secure-regions:
+        $ref: /schemas/types.yaml#/definitions/uint64-matrix
+        description:
+          Regions in the NAND chip which are protected using a secure element
+          like Trustzone. This property contains the start address and size of
+          the secure regions present.
+
     required:
       - reg
 
diff --git a/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml
new file mode 100644
index 000000000000..84ad7ff30121
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/qcom,nandc.yaml
@@ -0,0 +1,196 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/qcom,nandc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm NAND controller
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+properties:
+  compatible:
+    enum:
+      - qcom,ipq806x-nand
+      - qcom,ipq4019-nand
+      - qcom,ipq6018-nand
+      - qcom,ipq8074-nand
+      - qcom,sdx55-nand
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Core Clock
+      - description: Always ON Clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: aon
+
+  "#address-cells": true
+  "#size-cells": true
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    type: object
+    properties:
+      nand-bus-width:
+        const: 8
+
+      nand-ecc-strength:
+        enum: [1, 4, 8]
+
+      nand-ecc-step-size:
+        enum:
+          - 512
+
+allOf:
+  - $ref: "nand-controller.yaml#"
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: qcom,ipq806x-nand
+    then:
+      properties:
+        dmas:
+          items:
+            - description: rxtx DMA channel
+
+        dma-names:
+          items:
+            - const: rxtx
+
+        qcom,cmd-crci:
+          $ref: /schemas/types.yaml#/definitions/uint32
+          description:
+            Must contain the ADM command type CRCI block instance number
+            specified for the NAND controller on the given platform
+
+        qcom,data-crci:
+          $ref: /schemas/types.yaml#/definitions/uint32
+          description:
+            Must contain the ADM data type CRCI block instance number
+            specified for the NAND controller on the given platform
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,ipq4019-nand
+              - qcom,ipq6018-nand
+              - qcom,ipq8074-nand
+              - qcom,sdx55-nand
+
+    then:
+      properties:
+        dmas:
+          items:
+            - description: tx DMA channel
+            - description: rx DMA channel
+            - description: cmd DMA channel
+
+        dma-names:
+          items:
+            - const: tx
+            - const: rx
+            - const: cmd
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+    nand-controller@1ac00000 {
+      compatible = "qcom,ipq806x-nand";
+      reg = <0x1ac00000 0x800>;
+
+      clocks = <&gcc EBI2_CLK>,
+               <&gcc EBI2_AON_CLK>;
+      clock-names = "core", "aon";
+
+      dmas = <&adm_dma 3>;
+      dma-names = "rxtx";
+      qcom,cmd-crci = <15>;
+      qcom,data-crci = <3>;
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      nand@0 {
+        reg = <0>;
+
+        nand-ecc-strength = <4>;
+        nand-bus-width = <8>;
+
+        partitions {
+          compatible = "fixed-partitions";
+          #address-cells = <1>;
+          #size-cells = <1>;
+
+          partition@0 {
+            label = "boot-nand";
+            reg = <0 0x58a0000>;
+          };
+
+          partition@58a0000 {
+            label = "fs-nand";
+            reg = <0x58a0000 0x4000000>;
+          };
+        };
+      };
+    };
+
+    #include <dt-bindings/clock/qcom,gcc-ipq4019.h>
+    nand-controller@79b0000 {
+      compatible = "qcom,ipq4019-nand";
+      reg = <0x79b0000 0x1000>;
+
+      clocks = <&gcc GCC_QPIC_CLK>,
+               <&gcc GCC_QPIC_AHB_CLK>;
+      clock-names = "core", "aon";
+
+      dmas = <&qpicbam 0>,
+             <&qpicbam 1>,
+             <&qpicbam 2>;
+      dma-names = "tx", "rx", "cmd";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      nand@0 {
+        reg = <0>;
+        nand-ecc-strength = <4>;
+        nand-bus-width = <8>;
+
+        partitions {
+          compatible = "fixed-partitions";
+          #address-cells = <1>;
+          #size-cells = <1>;
+
+          partition@0 {
+            label = "boot-nand";
+            reg = <0 0x58a0000>;
+          };
+
+          partition@58a0000 {
+            label = "fs-nand";
+            reg = <0x58a0000 0x4000000>;
+          };
+        };
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
deleted file mode 100644
index 5647913d8837..000000000000
--- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
+++ /dev/null
@@ -1,142 +0,0 @@
-* Qualcomm NAND controller
-
-Required properties:
-- compatible:		must be one of the following:
-    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
-			    SoC and it uses ADM DMA
-    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
-                            IPQ4019 SoC and it uses BAM DMA
-    * "qcom,ipq6018-nand" - for QPIC NAND controller v1.5.0 being used in
-                            IPQ6018 SoC and it uses BAM DMA
-    * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
-                            IPQ8074 SoC and it uses BAM DMA
-    * "qcom,sdx55-nand"   - for QPIC NAND controller v2.0.0 being used in
-                            SDX55 SoC and it uses BAM DMA
-
-- reg:			MMIO address range
-- clocks:		must contain core clock and always on clock
-- clock-names:		must contain "core" for the core clock and "aon" for the
-			always on clock
-
-EBI2 specific properties:
-- dmas:			DMA specifier, consisting of a phandle to the ADM DMA
-			controller node and the channel number to be used for
-			NAND. Refer to dma.txt and qcom_adm.txt for more details
-- dma-names:		must be "rxtx"
-- qcom,cmd-crci:	must contain the ADM command type CRCI block instance
-			number specified for the NAND controller on the given
-			platform
-- qcom,data-crci:	must contain the ADM data type CRCI block instance
-			number specified for the NAND controller on the given
-			platform
-
-QPIC specific properties:
-- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
-			and the channel number to be used for NAND. Refer to
-			dma.txt, qcom_bam_dma.txt for more details
-- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
-- #address-cells:	<1> - subnodes give the chip-select number
-- #size-cells:		<0>
-
-* NAND chip-select
-
-Each controller may contain one or more subnodes to represent enabled
-chip-selects which (may) contain NAND flash chips. Their properties are as
-follows.
-
-Required properties:
-- reg:			a single integer representing the chip-select
-			number (e.g., 0, 1, 2, etc.)
-- #address-cells:	see partition.txt
-- #size-cells:		see partition.txt
-
-Optional properties:
-- nand-bus-width:	see nand-controller.yaml
-- nand-ecc-strength:	see nand-controller.yaml. If not specified, then ECC strength will
-			be used according to chip requirement and available
-			OOB size.
-
-Each nandcs device node may optionally contain a 'partitions' sub-node, which
-further contains sub-nodes describing the flash partition mapping. See
-partition.txt for more detail.
-
-Example:
-
-nand-controller@1ac00000 {
-	compatible = "qcom,ipq806x-nand";
-	reg = <0x1ac00000 0x800>;
-
-	clocks = <&gcc EBI2_CLK>,
-		 <&gcc EBI2_AON_CLK>;
-	clock-names = "core", "aon";
-
-	dmas = <&adm_dma 3>;
-	dma-names = "rxtx";
-	qcom,cmd-crci = <15>;
-	qcom,data-crci = <3>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nand@0 {
-		reg = <0>;
-
-		nand-ecc-strength = <4>;
-		nand-bus-width = <8>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "boot-nand";
-				reg = <0 0x58a0000>;
-			};
-
-			partition@58a0000 {
-				label = "fs-nand";
-				reg = <0x58a0000 0x4000000>;
-			};
-		};
-	};
-};
-
-nand-controller@79b0000 {
-	compatible = "qcom,ipq4019-nand";
-	reg = <0x79b0000 0x1000>;
-
-	clocks = <&gcc GCC_QPIC_CLK>,
-		<&gcc GCC_QPIC_AHB_CLK>;
-	clock-names = "core", "aon";
-
-	dmas = <&qpicbam 0>,
-		<&qpicbam 1>,
-		<&qpicbam 2>;
-	dma-names = "tx", "rx", "cmd";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	nand@0 {
-		reg = <0>;
-		nand-ecc-strength = <4>;
-		nand-bus-width = <8>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "boot-nand";
-				reg = <0 0x58a0000>;
-			};
-
-			partition@58a0000 {
-				label = "fs-nand";
-				reg = <0x58a0000 0x4000000>;
-			};
-		};
-	};
-};