Merge tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late cleanups from Arnd Bergmann:
 "These could not be part of the first cleanup branch, because they
  either came too late in the cycle, or they have dependencies on other
  branches.  Important changes are:

   - The integrator platform is almost multiplatform capable after some
     reorganization (Linus Walleij)
   - Minor cleanups on Zynq (Michal Simek)
   - Lots of changes for Exynos and other Samsung platforms, including
     further preparations for multiplatform support and the clocks
     bindings are rearranged"

* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  devicetree: fix newly added exynos sata bindings
  ARM: EXYNOS: Fix compilation error in cpuidle.c
  ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
  ARM: EXYNOS: Remove hardware.h file
  ARM: SAMSUNG: Remove hardware.h inclusion
  ARM: S3C24XX: Remove invalid code from hardware.h
  dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
  ARM: dts: Keep some essential LDOs enabled for arndale-octa board
  ARM: dts: Disable MDMA1 node for arndale-octa board
  ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
  serial: s3c: Fix build of header without serial_core.h preinclusion
  ARM: EXYNOS: Allow wake-up using GIC interrupts
  ARM: EXYNOS: Stop using legacy Samsung PM code
  ARM: EXYNOS: Remove PM initcalls and useless indirection
  ARM: EXYNOS: Fix abuse of CONFIG_PM
  ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
  ARM: SAMSUNG: Move common save/restore helpers to separate file
  ARM: SAMSUNG: Move Samsung PM debug code into separate file
  ARM: SAMSUNG: Consolidate PM debug functions
  ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
  ...

2 files changed, 22 insertions, 23 deletions

diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
deleted file mode 100644
index 37824fac688e..000000000000
--- a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
+++ /dev/null
@@ -1,14 +0,0 @@
-* Samsung SATA PHY Controller
-
-SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
-Each SATA PHY controller should have its own node.
-
-Required properties:
-- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
-- reg               : <registers mapping>
-
-Example:
-        sata@ffe07000 {
-                compatible = "samsung,exynos5-sata-phy";
-                reg = <0xffe07000 0x1000>;
-        };
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
index 0849f1025e34..cb48448247ea 100644
--- a/Documentation/devicetree/bindings/ata/exynos-sata.txt
+++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt
@@ -4,14 +4,27 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
 Required properties:
-- compatible        : compatible list, contains "samsung,exynos5-sata"
-- interrupts        : <interrupt mapping for SATA IRQ>
-- reg               : <registers mapping>
-- samsung,sata-freq : <frequency in MHz>
+- compatible		: compatible list, contains "samsung,exynos5-sata"
+- interrupts		: <interrupt mapping for SATA IRQ>
+- reg			: <registers mapping>
+- samsung,sata-freq	: <frequency in MHz>
+- phys			: Must contain exactly one entry as specified
+			  in phy-bindings.txt
+- phy-names		: Must be "sata-phy"
+
+Optional properties:
+- clocks		: Must contain an entry for each entry in clock-names.
+- clock-names		: Shall be "sata" for the external SATA bus clock,
+			  and "sclk_sata" for the internal controller clock.
 
 Example:
-        sata@ffe08000 {
-                compatible = "samsung,exynos5-sata";
-                reg = <0xffe08000 0x1000>;
-                interrupts = <115>;
-        };
+	sata@122f0000 {
+		compatible = "snps,dwc-ahci";
+		samsung,sata-freq = <66>;
+		reg = <0x122f0000 0x1ff>;
+		interrupts = <0 115 0>;
+		clocks = <&clock 277>, <&clock 143>;
+		clock-names = "sata", "sclk_sata";
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+	};