Merge branch 'regulator-5.1' into regulator-next

89 files changed, 2327 insertions, 1369 deletions

diff --git a/.mailmap b/.mailmap
index ea98fcc197e4..37e1847c7988 100644
--- a/.mailmap
+++ b/.mailmap
@@ -123,6 +123,7 @@ Mark Brown <broonie@sirena.org.uk>
 Mark Yao <markyao0591@gmail.com> <mark.yao@rock-chips.com>
 Martin Kepplinger <martink@posteo.de> <martin.kepplinger@theobroma-systems.com>
 Martin Kepplinger <martink@posteo.de> <martin.kepplinger@ginzinger.com>
+Mathieu Othacehe <m.othacehe@gmail.com>
 Matthew Wilcox <willy@infradead.org> <matthew.r.wilcox@intel.com>
 Matthew Wilcox <willy@infradead.org> <matthew@wil.cx>
 Matthew Wilcox <willy@infradead.org> <mawilcox@linuxonhyperv.com>
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
index a4b056761eaa..d5f68ac78d15 100644
--- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
@@ -23,6 +23,20 @@ Required properties:
 
 Optional properties:
 - clock-output-names	: Should contain name for output clock.
+- rohm,reset-snvs-powered : Transfer BD718x7 to SNVS state at reset.
+
+The BD718x7 supports two different HW states as reset target states. States
+are called as SNVS and READY. At READY state all the PMIC power outputs go
+down and OTP is reload. At the SNVS state all other logic and external
+devices apart from the SNVS power domain are shut off. Please refer to NXP
+i.MX8 documentation for further information regarding SNVS state. When a
+reset is done via SNVS state the PMIC OTP data is not reload. This causes
+power outputs that have been under SW control to stay down when reset has
+switched power state to SNVS. If reset is done via READY state the power
+outputs will be returned to HW control by OTP loading. Thus the reset
+target state is set to READY by default. If SNVS state is used the boot
+crucial regulators must have the regulator-always-on and regulator-boot-on
+properties set in regulator node.
 
 Example:
 
@@ -43,6 +57,7 @@ Example:
 		#clock-cells = <0>;
 		clocks = <&osc 0>;
 		clock-output-names = "bd71837-32k-out";
+		rohm,reset-snvs-powered;
 
 		regulators {
 			buck1: BUCK1 {
@@ -50,8 +65,10 @@ Example:
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1300000>;
 				regulator-boot-on;
+				regulator-always-on;
 				regulator-ramp-delay = <1250>;
 			};
+			// [...]
 		};
 	};
 
diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt
index 54a3f2c80e3a..e7fc045281d1 100644
--- a/Documentation/devicetree/bindings/regulator/fan53555.txt
+++ b/Documentation/devicetree/bindings/regulator/fan53555.txt
@@ -1,7 +1,8 @@
 Binding for Fairchild FAN53555 regulators
 
 Required properties:
-  - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828"
+  - compatible: one of "fcs,fan53555", "fcs,fan53526", "silergy,syr827" or
+		"silergy,syr828"
   - reg: I2C address
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt
deleted file mode 100644
index 0c2a6c8a1536..000000000000
--- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt
+++ /dev/null
@@ -1,35 +0,0 @@
-Fixed Voltage regulators
-
-Required properties:
-- compatible: Must be "regulator-fixed";
-- regulator-name: Defined in regulator.txt as optional, but required here.
-
-Optional properties:
-- gpio: gpio to use for enable control
-- startup-delay-us: startup time in microseconds
-- enable-active-high: Polarity of GPIO is Active high
-If this property is missing, the default assumed is Active low.
-- gpio-open-drain: GPIO is open drain type.
-  If this property is missing then default assumption is false.
--vin-supply: Input supply name.
-
-Any property defined as part of the core regulator
-binding, defined in regulator.txt, can also be used.
-However a fixed voltage regulator is expected to have the
-regulator-min-microvolt and regulator-max-microvolt
-to be the same.
-
-Example:
-
-	abc: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-supply";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio1 16 0>;
-		startup-delay-us = <70000>;
-		enable-active-high;
-		regulator-boot-on;
-		gpio-open-drain;
-		vin-supply = <&parent_reg>;
-	};
diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml
new file mode 100644
index 000000000000..d289c2f7455a
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/fixed-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Fixed Voltage regulators
+
+maintainers:
+  - Liam Girdwood <lgirdwood@gmail.com>
+  - Mark Brown <broonie@kernel.org>
+
+description:
+  Any property defined as part of the core regulator binding, defined in
+  regulator.txt, can also be used. However a fixed voltage regulator is
+  expected to have the regulator-min-microvolt and regulator-max-microvolt
+  to be the same.
+
+properties:
+  compatible:
+    const: regulator-fixed
+
+  regulator-name: true
+
+  gpio:
+    description: gpio to use for enable control
+    maxItems: 1
+
+  startup-delay-us:
+    description: startup time in microseconds
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  enable-active-high:
+    description:
+      Polarity of GPIO is Active high. If this property is missing,
+      the default assumed is Active low.
+    type: boolean
+
+  gpio-open-drain:
+    description:
+      GPIO is open drain type. If this property is missing then default
+      assumption is false.
+    type: boolean
+
+  vin-supply:
+    description: Input supply phandle.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+required:
+  - compatible
+  - regulator-name
+
+examples:
+  - |
+    reg_1v8: regulator-1v8 {
+      compatible = "regulator-fixed";
+      regulator-name = "1v8";
+      regulator-min-microvolt = <1800000>;
+      regulator-max-microvolt = <1800000>;
+      gpio = <&gpio1 16 0>;
+      startup-delay-us = <70000>;
+      enable-active-high;
+      regulator-boot-on;
+      gpio-open-drain;
+      vin-supply = <&parent_reg>;
+    };
+...
diff --git a/Documentation/devicetree/bindings/regulator/max77650-regulator.txt b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt
new file mode 100644
index 000000000000..f1cbe813c30f
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt
@@ -0,0 +1,41 @@
+Regulator driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The regulator controller is represented as a sub-node of the PMIC node
+on the device tree.
+
+The device has a single LDO regulator and a SIMO buck-boost regulator with
+three independent power rails.
+
+Required properties:
+--------------------
+- compatible:		Must be "maxim,max77650-regulator"
+
+Each rail must be instantiated under the regulators subnode of the top PMIC
+node. Up to four regulators can be defined. For standard regulator properties
+refer to Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Available regulator compatible strings are: "ldo", "sbb0", "sbb1", "sbb2".
+
+Example:
+--------
+
+	regulators {
+		compatible = "maxim,max77650-regulator";
+
+		max77650_ldo: regulator@0 {
+			regulator-compatible = "ldo";
+			regulator-name = "max77650-ldo";
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <2937500>;
+		};
+
+		max77650_sbb0: regulator@1 {
+			regulator-compatible = "sbb0";
+			regulator-name = "max77650-sbb0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1587500>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt
index f9be1acf891c..4d3b12b92cb3 100644
--- a/Documentation/devicetree/bindings/regulator/pfuze100.txt
+++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt
@@ -8,7 +8,7 @@ Optional properties:
 - fsl,pfuze-support-disable-sw: Boolean, if present disable all unused switch
   regulators to save power consumption. Attention, ensure that all important
   regulators (e.g. DDR ref, DDR supply) has set the "regulator-always-on"
-  property. If not present, the switched regualtors are always on and can't be
+  property. If not present, the switched regulators are always on and can't be
   disabled. This binding is a workaround to keep backward compatibility with
   old dtb's which rely on the fact that the switched regulators are always on
   and don't mark them explicit as "regulator-always-on".
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt
new file mode 100644
index 000000000000..698cfc3bc3dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt
@@ -0,0 +1,68 @@
+ROHM BD70528 Power Management Integrated Circuit regulator bindings
+
+Required properties:
+ - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3",
+		   "led_ldo1", "led_ldo2"
+
+List of regulators provided by this controller. BD70528 regulators node
+should be sub node of the BD70528 MFD node. See BD70528 MFD bindings at
+Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt
+
+The valid names for BD70528 regulator nodes are:
+BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+regulators {
+	buck1: BUCK1 {
+		regulator-name = "buck1";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3400000>;
+		regulator-boot-on;
+		regulator-ramp-delay = <125>;
+	};
+	buck2: BUCK2 {
+		regulator-name = "buck2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-ramp-delay = <125>;
+	};
+	buck3: BUCK3 {
+		regulator-name = "buck3";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-ramp-delay = <250>;
+	};
+	ldo1: LDO1 {
+		regulator-name = "ldo1";
+		regulator-min-microvolt = <1650000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+	ldo2: LDO2 {
+		regulator-name = "ldo2";
+		regulator-min-microvolt = <1650000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	ldo3: LDO3 {
+		regulator-name = "ldo3";
+		regulator-min-microvolt = <1650000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	led_ldo1: LED_LDO1 {
+		regulator-name = "led_ldo1";
+		regulator-min-microvolt = <200000>;
+		regulator-max-microvolt = <300000>;
+	};
+	led_ldo2: LED_LDO2 {
+		regulator-name = "led_ldo2";
+		regulator-min-microvolt = <200000>;
+		regulator-max-microvolt = <300000>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
index 4b98ca26e61a..cbce62c22b60 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
@@ -27,8 +27,38 @@ BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6
 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
 
 Optional properties:
+- rohm,dvs-run-voltage		: PMIC default "RUN" state voltage in uV.
+				  See below table for bucks which support this.
+- rohm,dvs-idle-voltage		: PMIC default "IDLE" state voltage in uV.
+				  See below table for bucks which support this.
+- rohm,dvs-suspend-voltage	: PMIC default "SUSPEND" state voltage in uV.
+				  See below table for bucks which support this.
 - Any optional property defined in bindings/regulator/regulator.txt
 
+Supported default DVS states:
+
+BD71837:
+buck	| dvs-run-voltage	| dvs-idle-voltage	| dvs-suspend-voltage
+-----------------------------------------------------------------------------
+1	| supported		| supported		| supported
+----------------------------------------------------------------------------
+2	| supported		| supported		| not supported
+----------------------------------------------------------------------------
+3	| supported		| not supported		| not supported
+----------------------------------------------------------------------------
+4	| supported		| not supported		| not supported
+----------------------------------------------------------------------------
+rest	| not supported		| not supported		| not supported
+
+BD71847:
+buck	| dvs-run-voltage	| dvs-idle-voltage	| dvs-suspend-voltage
+-----------------------------------------------------------------------------
+1	| supported		| supported		| supported
+----------------------------------------------------------------------------
+2	| supported		| supported		| not supported
+----------------------------------------------------------------------------
+rest	| not supported		| not supported		| not supported
+
 Example:
 regulators {
 	buck1: BUCK1 {
@@ -36,7 +66,11 @@ regulators {
 		regulator-min-microvolt = <700000>;
 		regulator-max-microvolt = <1300000>;
 		regulator-boot-on;
+		regulator-always-on;
 		regulator-ramp-delay = <1250>;
+		rohm,dvs-run-voltage = <900000>;
+		rohm,dvs-idle-voltage = <850000>;
+		rohm,dvs-suspend-voltage = <800000>;
 	};
 	buck2: BUCK2 {
 		regulator-name = "buck2";
@@ -45,18 +79,22 @@ regulators {
 		regulator-boot-on;
 		regulator-always-on;
 		regulator-ramp-delay = <1250>;
+		rohm,dvs-run-voltage = <1000000>;
+		rohm,dvs-idle-voltage = <900000>;
 	};
 	buck3: BUCK3 {
 		regulator-name = "buck3";
 		regulator-min-microvolt = <700000>;
 		regulator-max-microvolt = <1300000>;
 		regulator-boot-on;
+		rohm,dvs-run-voltage = <1000000>;
 	};
 	buck4: BUCK4 {
 		regulator-name = "buck4";
 		regulator-min-microvolt = <700000>;
 		regulator-max-microvolt = <1300000>;
 		regulator-boot-on;
+		rohm,dvs-run-voltage = <1000000>;
 	};
 	buck5: BUCK5 {
 		regulator-name = "buck5";
diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt
index a3f476240565..6189df71ea98 100644
--- a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt
@@ -23,16 +23,14 @@ Switches are fixed voltage regulators with only enable/disable capability.
 Optional properties:
 - st,mask-reset: mask reset for this regulator: the regulator configuration
   is maintained during pmic reset.
-- regulator-pull-down: enable high pull down
-  if not specified light pull down is used
 - regulator-over-current-protection:
     if set, all regulators are switched off in case of over-current detection
     on this regulator,
     if not set, the driver only sends an over-current event.
-- interrupt-parent: phandle to the parent interrupt controller
 - interrupts: index of current limit detection interrupt
 - <regulator>-supply: phandle to the parent supply/regulator node
 	each regulator supply can be described except vref_ddr.
+- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2.
 
 Example:
 regulators {
@@ -43,7 +41,6 @@ regulators {
 	vdd_core: buck1 {
 		regulator-name = "vdd_core";
 		interrupts = <IT_CURLIM_BUCK1 0>;
-		interrupt-parent = <&pmic>;
 		st,mask-reset;
 		regulator-pull-down;
 		regulator-min-microvolt = <700000>;
@@ -53,7 +50,6 @@ regulators {
 	v3v3: buck4 {
 		regulator-name = "v3v3";
 		interrupts = <IT_CURLIM_BUCK4 0>;
-		interrupt-parent = <&mypmic>;
 
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt
index 02f0e9bbfbf8..54aded3b78e2 100644
--- a/Documentation/devicetree/bindings/regulator/tps65218.txt
+++ b/Documentation/devicetree/bindings/regulator/tps65218.txt
@@ -71,8 +71,13 @@ tps65218: tps65218@24 {
 		regulator-always-on;
 	};
 
+	ls2: regulator-ls2 {
+		regulator-min-microamp = <100000>;
+		regulator-max-microamp = <1000000>;
+	};
+
 	ls3: regulator-ls3 {
-		regulator-min-microvolt = <100000>;
-		regulator-max-microvolt = <1000000>;
+		regulator-min-microamp = <100000>;
+		regulator-max-microamp = <1000000>;
 	};
 };
diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c
index 2e1e540f2e5a..d278fb672d40 100644
--- a/arch/arm/mach-imx/mach-mx21ads.c
+++ b/arch/arm/mach-imx/mach-mx21ads.c
@@ -205,7 +205,6 @@ static struct regulator_init_data mx21ads_lcd_regulator_init_data = {
 static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = {
 	.supply_name	= "LCD",
 	.microvolts	= 3300000,
-	.enable_high	= 1,
 	.init_data	= &mx21ads_lcd_regulator_init_data,
 };
 
diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c
index f5e04047ed13..6dd7f57c332f 100644
--- a/arch/arm/mach-imx/mach-mx27ads.c
+++ b/arch/arm/mach-imx/mach-mx27ads.c
@@ -237,7 +237,7 @@ static struct fixed_voltage_config mx27ads_lcd_regulator_pdata = {
 static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = {
 	.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
 	.table = {
-		GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_LOW),
 		{ },
 	},
 };
diff --git a/arch/arm/mach-mmp/brownstone.c b/arch/arm/mach-mmp/brownstone.c
index a04e249c654b..d2560fb1e835 100644
--- a/arch/arm/mach-mmp/brownstone.c
+++ b/arch/arm/mach-mmp/brownstone.c
@@ -149,7 +149,6 @@ static struct regulator_init_data brownstone_v_5vp_data = {
 static struct fixed_voltage_config brownstone_v_5vp = {
 	.supply_name		= "v_5vp",
 	.microvolts		= 5000000,
-	.enable_high		= 1,
 	.enabled_at_boot	= 1,
 	.init_data		= &brownstone_v_5vp_data,
 };
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index c4c0a8ea11e4..be30c3c061b4 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -267,7 +267,6 @@ static struct fixed_voltage_config modem_nreset_config = {
 	.supply_name		= "modem_nreset",
 	.microvolts		= 3300000,
 	.startup_delay		= 25000,
-	.enable_high		= 1,
 	.enabled_at_boot	= 1,
 	.init_data		= &modem_nreset_data,
 };
@@ -533,7 +532,6 @@ static struct regulator_init_data keybrd_pwr_initdata = {
 static struct fixed_voltage_config keybrd_pwr_config = {
 	.supply_name		= "keybrd_pwr",
 	.microvolts		= 5000000,
-	.enable_high		= 1,
 	.init_data		= &keybrd_pwr_initdata,
 };
 
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 8a5b6ed4ec36..a2ecc5e69abb 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -330,7 +330,6 @@ static struct fixed_voltage_config pandora_vwlan = {
 	.supply_name		= "vwlan",
 	.microvolts		= 1800000, /* 1.8V */
 	.startup_delay		= 50000, /* 50ms */
-	.enable_high		= 1,
 	.init_data		= &pandora_vmmc3,
 };
 
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index 32c1edeb3f14..5ba7bb7f7d51 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -976,7 +976,6 @@ static struct fixed_voltage_config camera_dummy_config = {
 	.supply_name		= "camera_vdd",
 	.input_supply		= "vcc cam",
 	.microvolts		= 2800000,
-	.enable_high		= 0,
 	.init_data		= &camera_dummy_initdata,
 };
 
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index 565965e9acc7..5e110e70ce5a 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -714,7 +714,6 @@ static struct regulator_init_data camera_regulator_initdata = {
 static struct fixed_voltage_config camera_regulator_config = {
 	.supply_name		= "camera_vdd",
 	.microvolts		= 2800000,
-	.enable_high		= 0,
 	.init_data		= &camera_regulator_initdata,
 };
 
@@ -730,7 +729,7 @@ static struct gpiod_lookup_table camera_supply_gpiod_table = {
 	.dev_id = "reg-fixed-voltage.1",
 	.table = {
 		GPIO_LOOKUP("gpio-pxa", GPIO50_nCAM_EN,
-			    NULL, GPIO_ACTIVE_HIGH),
+			    NULL, GPIO_ACTIVE_LOW),
 		{ },
 	},
 };
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index b79b757fdd41..51d38d5e776a 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -19,6 +19,7 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/fb.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
@@ -702,9 +703,7 @@ static struct regulator_init_data bq24022_init_data = {
 	.consumer_supplies      = bq24022_consumers,
 };
 
-static struct gpio bq24022_gpios[] = {
-	{ GPIO96_HX4700_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" },
-};
+static enum gpiod_flags bq24022_gpiod_gflags[] = { GPIOD_OUT_LOW };
 
 static struct gpio_regulator_state bq24022_states[] = {
 	{ .value = 100000, .gpios = (0 << 0) },
@@ -714,12 +713,10 @@ static struct gpio_regulator_state bq24022_states[] = {
 static struct gpio_regulator_config bq24022_info = {
 	.supply_name = "bq24022",
 
-	.enable_gpio = GPIO72_HX4700_BQ24022_nCHARGE_EN,
-	.enable_high = 0,
 	.enabled_at_boot = 0,
 
-	.gpios = bq24022_gpios,
-	.nr_gpios = ARRAY_SIZE(bq24022_gpios),
+	.gflags = bq24022_gpiod_gflags,
+	.ngpios = ARRAY_SIZE(bq24022_gpiod_gflags),
 
 	.states = bq24022_states,
 	.nr_states = ARRAY_SIZE(bq24022_states),
@@ -736,6 +733,17 @@ static struct platform_device bq24022 = {
 	},
 };
 
+static struct gpiod_lookup_table bq24022_gpiod_table = {
+	.dev_id = "gpio-regulator",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO96_HX4700_BQ24022_ISET2,
+			    NULL, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO72_HX4700_BQ24022_nCHARGE_EN,
+			    "enable", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 /*
  * StrataFlash
  */
@@ -878,6 +886,7 @@ static void __init hx4700_init(void)
 	pxa_set_btuart_info(NULL);
 	pxa_set_stuart_info(NULL);
 
+	gpiod_add_lookup_table(&bq24022_gpiod_table);
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	pwm_add_table(hx4700_pwm_lookup, ARRAY_SIZE(hx4700_pwm_lookup));
 
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index 08b079653c3f..6538a7c0e504 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -645,9 +645,8 @@ static struct regulator_init_data bq24022_init_data = {
 	.consumer_supplies	= bq24022_consumers,
 };
 
-static struct gpio bq24022_gpios[] = {
-	{ EGPIO_MAGICIAN_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" },
-};
+
+static enum gpiod_flags bq24022_gpiod_gflags[] = { GPIOD_OUT_LOW };
 
 static struct gpio_regulator_state bq24022_states[] = {
 	{ .value = 100000, .gpios = (0 << 0) },
@@ -657,12 +656,10 @@ static struct gpio_regulator_state bq24022_states[] = {
 static struct gpio_regulator_config bq24022_info = {
 	.supply_name		= "bq24022",
 
-	.enable_gpio		= GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
-	.enable_high		= 0,
 	.enabled_at_boot	= 1,
 
-	.gpios			= bq24022_gpios,
-	.nr_gpios		= ARRAY_SIZE(bq24022_gpios),
+	.gflags = bq24022_gpiod_gflags,
+	.ngpios = ARRAY_SIZE(bq24022_gpiod_gflags),
 
 	.states			= bq24022_states,
 	.nr_states		= ARRAY_SIZE(bq24022_states),
@@ -679,6 +676,17 @@ static struct platform_device bq24022 = {
 	},
 };
 
+static struct gpiod_lookup_table bq24022_gpiod_table = {
+	.dev_id = "gpio-regulator",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", EGPIO_MAGICIAN_BQ24022_ISET2,
+			    NULL, GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
+			    "enable", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 /*
  * fixed regulator for ads7846
  */
@@ -1027,6 +1035,7 @@ static void __init magician_init(void)
 	regulator_register_always_on(0, "power", pwm_backlight_supply,
 		ARRAY_SIZE(pwm_backlight_supply), 5000000);
 
+	gpiod_add_lookup_table(&bq24022_gpiod_table);
 	platform_add_devices(ARRAY_AND_SIZE(devices));
 }
 
diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c
index e1db072756f2..e13bfc9b01d2 100644
--- a/arch/arm/mach-pxa/raumfeld.c
+++ b/arch/arm/mach-pxa/raumfeld.c
@@ -883,7 +883,6 @@ static struct regulator_init_data audio_va_initdata = {
 static struct fixed_voltage_config audio_va_config = {
 	.supply_name		= "audio_va",
 	.microvolts		= 5000000,
-	.enable_high		= 1,
 	.enabled_at_boot	= 0,
 	.init_data		= &audio_va_initdata,
 };
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index c411f79d4cb5..ebd654302387 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -426,7 +426,7 @@ static struct gpiod_lookup_table can_regulator_gpiod_table = {
 	.dev_id = "reg-fixed-voltage.0",
 	.table = {
 		GPIO_LOOKUP("gpio-pxa", ZEUS_CAN_SHDN_GPIO,
-			    NULL, GPIO_ACTIVE_HIGH),
+			    NULL, GPIO_ACTIVE_LOW),
 		{ },
 	},
 };
@@ -547,7 +547,6 @@ static struct regulator_init_data zeus_ohci_regulator_data = {
 static struct fixed_voltage_config zeus_ohci_regulator_config = {
 	.supply_name		= "vbus2",
 	.microvolts		= 5000000, /* 5.0V */
-	.enable_high		= 1,
 	.startup_delay		= 0,
 	.init_data		= &zeus_ohci_regulator_data,
 };
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index dfa42496ec27..d09c3f236186 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -469,7 +469,6 @@ static struct regulator_consumer_supply assabet_cf_vcc_consumers[] = {
 static struct fixed_voltage_config assabet_cf_vcc_pdata __initdata = {
 	.supply_name = "cf-power",
 	.microvolts = 3300000,
-	.enable_high = 1,
 };
 
 static struct gpiod_lookup_table assabet_cf_vcc_gpio_table = {
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index 22b4106b8084..5495efa07335 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -630,7 +630,6 @@ static struct regulator_init_data cn12_power_init_data = {
 static struct fixed_voltage_config cn12_power_info = {
 	.supply_name = "CN12 SD/MMC Vdd",
 	.microvolts = 3300000,
-	.enable_high = 1,
 	.init_data = &cn12_power_init_data,
 };
 
@@ -671,7 +670,6 @@ static struct regulator_init_data sdhi0_power_init_data = {
 static struct fixed_voltage_config sdhi0_power_info = {
 	.supply_name = "CN11 SD/MMC Vdd",
 	.microvolts = 3300000,
-	.enable_high = 1,
 	.init_data = &sdhi0_power_init_data,
 };
 
diff --git a/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c b/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c
index 96f438d4b026..1421d5330b2c 100644
--- a/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c
+++ b/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c
@@ -44,7 +44,6 @@ static struct fixed_voltage_config bcm43xx_vmmc = {
 	 */
 	.microvolts		= 2000000,		/* 1.8V */
 	.startup_delay		= 250 * 1000,		/* 250ms */
-	.enable_high		= 1,			/* active high */
 	.enabled_at_boot	= 0,			/* disabled at boot */
 	.init_data		= &bcm43xx_vmmc_data,
 };
diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c
index 28f55248eb90..753a6a1b30c3 100644
--- a/drivers/regulator/88pm8607.c
+++ b/drivers/regulator/88pm8607.c
@@ -11,7 +11,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/err.h>
-#include <linux/i2c.h>
 #include <linux/of.h>
 #include <linux/regulator/of_regulator.h>
 #include <linux/platform_device.h>
@@ -22,12 +21,7 @@
 
 struct pm8607_regulator_info {
 	struct regulator_desc	desc;
-	struct pm860x_chip	*chip;
-	struct regulator_dev	*regulator;
-	struct i2c_client	*i2c;
-	struct i2c_client	*i2c_8606;
 
-	unsigned int	*vol_table;
 	unsigned int	*vol_suspend;
 
 	int	slope_double;
@@ -210,13 +204,15 @@ static const unsigned int LDO14_suspend_table[] = {
 static int pm8607_list_voltage(struct regulator_dev *rdev, unsigned index)
 {
 	struct pm8607_regulator_info *info = rdev_get_drvdata(rdev);
-	int ret = -EINVAL;
+	int ret;
+
+	ret = regulator_list_voltage_table(rdev, index);
+	if (ret < 0)
+		return ret;
+
+	if (info->slope_double)
+		ret <<= 1;
 
-	if (info->vol_table && (index < rdev->desc->n_voltages)) {
-		ret = info->vol_table[index];
-		if (info->slope_double)
-			ret <<= 1;
-	}
 	return ret;
 }
 
@@ -257,6 +253,7 @@ static const struct regulator_ops pm8606_preg_ops = {
 		.type	= REGULATOR_VOLTAGE,				\
 		.id	= PM8607_ID_##vreg,				\
 		.owner	= THIS_MODULE,					\
+		.volt_table = vreg##_table,				\
 		.n_voltages = ARRAY_SIZE(vreg##_table),			\
 		.vsel_reg = PM8607_##vreg,				\
 		.vsel_mask = ARRAY_SIZE(vreg##_table) - 1,		\
@@ -266,7 +263,6 @@ static const struct regulator_ops pm8606_preg_ops = {
 		.enable_mask = 1 << (ebit),				\
 	},								\
 	.slope_double	= (0),						\
-	.vol_table	= (unsigned int *)&vreg##_table,		\
 	.vol_suspend	= (unsigned int *)&vreg##_suspend_table,	\
 }
 
@@ -278,6 +274,7 @@ static const struct regulator_ops pm8606_preg_ops = {
 		.type	= REGULATOR_VOLTAGE,				\
 		.id	= PM8607_ID_LDO##_id,				\
 		.owner	= THIS_MODULE,					\
+		.volt_table = LDO##_id##_table,				\
 		.n_voltages = ARRAY_SIZE(LDO##_id##_table),		\
 		.vsel_reg = PM8607_##vreg,				\
 		.vsel_mask = (ARRAY_SIZE(LDO##_id##_table) - 1) << (shift), \
@@ -285,7 +282,6 @@ static const struct regulator_ops pm8606_preg_ops = {
 		.enable_mask = 1 << (ebit),				\
 	},								\
 	.slope_double	= (0),						\
-	.vol_table	= (unsigned int *)&LDO##_id##_table,		\
 	.vol_suspend	= (unsigned int *)&LDO##_id##_suspend_table,	\
 }
 
@@ -349,6 +345,7 @@ static int pm8607_regulator_probe(struct platform_device *pdev)
 	struct pm8607_regulator_info *info = NULL;
 	struct regulator_init_data *pdata = dev_get_platdata(&pdev->dev);
 	struct regulator_config config = { };
+	struct regulator_dev *rdev;
 	struct resource *res;
 	int i;
 
@@ -371,13 +368,9 @@ static int pm8607_regulator_probe(struct platform_device *pdev)
 		/* i is used to check regulator ID */
 		i = -1;
 	}
-	info->i2c = (chip->id == CHIP_PM8607) ? chip->client : chip->companion;
-	info->i2c_8606 = (chip->id == CHIP_PM8607) ? chip->companion :
-			chip->client;
-	info->chip = chip;
 
 	/* check DVC ramp slope double */
-	if ((i == PM8607_ID_BUCK3) && info->chip->buck3_double)
+	if ((i == PM8607_ID_BUCK3) && chip->buck3_double)
 		info->slope_double = 1;
 
 	config.dev = &pdev->dev;
@@ -392,12 +385,11 @@ static int pm8607_regulator_probe(struct platform_device *pdev)
 	else
 		config.regmap = chip->regmap_companion;
 
-	info->regulator = devm_regulator_register(&pdev->dev, &info->desc,
-						  &config);
-	if (IS_ERR(info->regulator)) {
+	rdev = devm_regulator_register(&pdev->dev, &info->desc, &config);
+	if (IS_ERR(rdev)) {
 		dev_err(&pdev->dev, "failed to register regulator %s\n",
 			info->desc.name);
-		return PTR_ERR(info->regulator);
+		return PTR_ERR(rdev);
 	}
 
 	platform_set_drvdata(pdev, info);
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index ee60a222f5eb..b7f249ee5e68 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
 	  BCM590xx PMUs. This will enable support for the software
 	  controllable LDO/Switching regulators.
 
+config REGULATOR_BD70528
+	tristate "ROHM BD70528 Power Regulator"
+	depends on MFD_ROHM_BD70528
+	help
+	  This driver supports voltage regulators on ROHM BD70528 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd70528-regulator.
+
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
@@ -457,6 +468,14 @@ config REGULATOR_MAX77620
 	  chip to control Step-Down DC-DC and LDOs. Say Y here to
 	  enable the regulator driver.
 
+config REGULATOR_MAX77650
+	tristate "Maxim MAX77650/77651 regulator support"
+	depends on MFD_MAX77650
+	help
+	  Regulator driver for MAX77650/77651 PMIC from Maxim
+	  Semiconductor. This device has a SIMO with three independent
+	  power rails and an LDO.
+
 config REGULATOR_MAX8649
 	tristate "Maxim 8649 voltage regulator"
 	depends on I2C
@@ -484,7 +503,7 @@ config REGULATOR_MAX8925
 	tristate "Maxim MAX8925 Power Management IC"
 	depends on MFD_MAX8925
 	help
-	  Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC.
+	  Say y here to support the voltage regulator of Maxim MAX8925 PMIC.
 
 config REGULATOR_MAX8952
 	tristate "Maxim MAX8952 Power Management IC"
@@ -501,7 +520,7 @@ config REGULATOR_MAX8973
 	select REGMAP_I2C
 	help
 	  The MAXIM MAX8973 high-efficiency. three phase, DC-DC step-down
-	  switching regulator delievers up to 9A of output current. Each
+	  switching regulator delivers up to 9A of output current. Each
 	  phase operates at a 2MHz fixed frequency with a 120 deg shift
 	  from the adjacent phase, allowing the use of small magnetic component.
 
@@ -646,7 +665,7 @@ config REGULATOR_PCF50633
 	tristate "NXP PCF50633 regulator driver"
 	depends on MFD_PCF50633
 	help
-	 Say Y here to support the voltage regulators and convertors
+	 Say Y here to support the voltage regulators and converters
 	 on PCF50633
 
 config REGULATOR_PFUZE100
@@ -924,7 +943,7 @@ config REGULATOR_TPS65132
 	select REGMAP_I2C
 	help
 	  This driver supports TPS65132 single inductor - dual output
-	  power supply specifcally designed for display panels.
+	  power supply specifically designed for display panels.
 
 config REGULATOR_TPS65217
 	tristate "TI TPS65217 Power regulators"
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index b12e1c9b2118..1169f8a27d91 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
 obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o
 obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
@@ -60,6 +61,7 @@ obj-$(CONFIG_REGULATOR_LTC3676) += ltc3676.o
 obj-$(CONFIG_REGULATOR_MAX14577) += max14577-regulator.o
 obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
 obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o
+obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8649)	+= max8649.o
 obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
 obj-$(CONFIG_REGULATOR_MAX8907) += max8907-regulator.o
diff --git a/drivers/regulator/act8865-regulator.c b/drivers/regulator/act8865-regulator.c
index 21e20483bd91..e0239cf3f56d 100644
--- a/drivers/regulator/act8865-regulator.c
+++ b/drivers/regulator/act8865-regulator.c
@@ -131,7 +131,7 @@
  * ACT8865 voltage number
  */
 #define	ACT8865_VOLTAGE_NUM	64
-#define ACT8600_SUDCDC_VOLTAGE_NUM	255
+#define ACT8600_SUDCDC_VOLTAGE_NUM	256
 
 struct act8865 {
 	struct regmap *regmap;
@@ -222,7 +222,8 @@ static const struct regulator_linear_range act8600_sudcdc_voltage_ranges[] = {
 	REGULATOR_LINEAR_RANGE(3000000, 0, 63, 0),
 	REGULATOR_LINEAR_RANGE(3000000, 64, 159, 100000),
 	REGULATOR_LINEAR_RANGE(12600000, 160, 191, 200000),
-	REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
+	REGULATOR_LINEAR_RANGE(19000000, 192, 247, 400000),
+	REGULATOR_LINEAR_RANGE(41400000, 248, 255, 0),
 };
 
 static struct regulator_ops act8865_ops = {
diff --git a/drivers/regulator/act8945a-regulator.c b/drivers/regulator/act8945a-regulator.c
index 603db77723b6..caa61d306a69 100644
--- a/drivers/regulator/act8945a-regulator.c
+++ b/drivers/regulator/act8945a-regulator.c
@@ -87,7 +87,8 @@ static const struct regulator_linear_range act8945a_voltage_ranges[] = {
 static int act8945a_set_suspend_state(struct regulator_dev *rdev, bool enable)
 {
 	struct regmap *regmap = rdev->regmap;
-	int id = rdev->desc->id, reg, val;
+	int id = rdev_get_id(rdev);
+	int reg, val;
 
 	switch (id) {
 	case ACT8945A_ID_DCDC1:
@@ -159,7 +160,7 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
 	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
 	struct regmap *regmap = rdev->regmap;
-	int id = rdev->desc->id;
+	int id = rdev_get_id(rdev);
 	int reg, ret, val = 0;
 
 	switch (id) {
@@ -190,11 +191,11 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode)
 
 	switch (mode) {
 	case REGULATOR_MODE_STANDBY:
-		if (rdev->desc->id > ACT8945A_ID_DCDC3)
+		if (id > ACT8945A_ID_DCDC3)
 			val = BIT(5);
 		break;
 	case REGULATOR_MODE_NORMAL:
-		if (rdev->desc->id <= ACT8945A_ID_DCDC3)
+		if (id <= ACT8945A_ID_DCDC3)
 			val = BIT(5);
 		break;
 	default:
@@ -213,7 +214,7 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode)
 static unsigned int act8945a_get_mode(struct regulator_dev *rdev)
 {
 	struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev);
-	int id = rdev->desc->id;
+	int id = rdev_get_id(rdev);
 
 	if (id < ACT8945A_ID_DCDC1 || id >= ACT8945A_ID_MAX)
 		return -EINVAL;
diff --git a/drivers/regulator/arizona-ldo1.c b/drivers/regulator/arizona-ldo1.c
index b9a93049e41e..bf3ab405eed1 100644
--- a/drivers/regulator/arizona-ldo1.c
+++ b/drivers/regulator/arizona-ldo1.c
@@ -40,35 +40,10 @@ struct arizona_ldo1 {
 	struct gpio_desc *ena_gpiod;
 };
 
-static int arizona_ldo1_hc_list_voltage(struct regulator_dev *rdev,
-					unsigned int selector)
-{
-	if (selector >= rdev->desc->n_voltages)
-		return -EINVAL;
-
-	if (selector == rdev->desc->n_voltages - 1)
-		return 1800000;
-	else
-		return rdev->desc->min_uV + (rdev->desc->uV_step * selector);
-}
-
-static int arizona_ldo1_hc_map_voltage(struct regulator_dev *rdev,
-				       int min_uV, int max_uV)
-{
-	int sel;
-
-	sel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);
-	if (sel >= rdev->desc->n_voltages)
-		sel = rdev->desc->n_voltages - 1;
-
-	return sel;
-}
-
 static int arizona_ldo1_hc_set_voltage_sel(struct regulator_dev *rdev,
 					   unsigned sel)
 {
-	struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev);
-	struct regmap *regmap = ldo->regmap;
+	struct regmap *regmap = rdev_get_regmap(rdev);
 	unsigned int val;
 	int ret;
 
@@ -85,16 +60,12 @@ static int arizona_ldo1_hc_set_voltage_sel(struct regulator_dev *rdev,
 	if (val)
 		return 0;
 
-	val = sel << ARIZONA_LDO1_VSEL_SHIFT;
-
-	return regmap_update_bits(regmap, ARIZONA_LDO1_CONTROL_1,
-				  ARIZONA_LDO1_VSEL_MASK, val);
+	return regulator_set_voltage_sel_regmap(rdev, sel);
 }
 
 static int arizona_ldo1_hc_get_voltage_sel(struct regulator_dev *rdev)
 {
-	struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev);
-	struct regmap *regmap = ldo->regmap;
+	struct regmap *regmap = rdev_get_regmap(rdev);
 	unsigned int val;
 	int ret;
 
@@ -105,32 +76,35 @@ static int arizona_ldo1_hc_get_voltage_sel(struct regulator_dev *rdev)
 	if (val & ARIZONA_LDO1_HI_PWR)
 		return rdev->desc->n_voltages - 1;
 
-	ret = regmap_read(regmap, ARIZONA_LDO1_CONTROL_1, &val);
-	if (ret != 0)
-		return ret;
-
-	return (val & ARIZONA_LDO1_VSEL_MASK) >> ARIZONA_LDO1_VSEL_SHIFT;
+	return regulator_get_voltage_sel_regmap(rdev);
 }
 
 static const struct regulator_ops arizona_ldo1_hc_ops = {
-	.list_voltage = arizona_ldo1_hc_list_voltage,
-	.map_voltage = arizona_ldo1_hc_map_voltage,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
 	.get_voltage_sel = arizona_ldo1_hc_get_voltage_sel,
 	.set_voltage_sel = arizona_ldo1_hc_set_voltage_sel,
 	.get_bypass = regulator_get_bypass_regmap,
 	.set_bypass = regulator_set_bypass_regmap,
 };
 
+static const struct regulator_linear_range arizona_ldo1_hc_ranges[] = {
+	REGULATOR_LINEAR_RANGE(900000, 0, 0x6, 50000),
+	REGULATOR_LINEAR_RANGE(1800000, 0x7, 0x7, 0),
+};
+
 static const struct regulator_desc arizona_ldo1_hc = {
 	.name = "LDO1",
 	.supply_name = "LDOVDD",
 	.type = REGULATOR_VOLTAGE,
 	.ops = &arizona_ldo1_hc_ops,
 
+	.vsel_reg = ARIZONA_LDO1_CONTROL_1,
+	.vsel_mask = ARIZONA_LDO1_VSEL_MASK,
 	.bypass_reg = ARIZONA_LDO1_CONTROL_1,
 	.bypass_mask = ARIZONA_LDO1_BYPASS,
-	.min_uV = 900000,
-	.uV_step = 50000,
+	.linear_ranges = arizona_ldo1_hc_ranges,
+	.n_linear_ranges = ARRAY_SIZE(arizona_ldo1_hc_ranges),
 	.n_voltages = 8,
 	.enable_time = 1500,
 	.ramp_delay = 24000,
diff --git a/drivers/regulator/as3722-regulator.c b/drivers/regulator/as3722-regulator.c
index 66337e12719b..e5fed289b52d 100644
--- a/drivers/regulator/as3722-regulator.c
+++ b/drivers/regulator/as3722-regulator.c
@@ -886,7 +886,7 @@ static int as3722_regulator_probe(struct platform_device *pdev)
 				as3722_regs->desc[id].min_uV = 410000;
 			} else {
 				as3722_regs->desc[id].n_voltages =
-					AS3722_SD0_VSEL_MAX + 1,
+					AS3722_SD0_VSEL_MAX + 1;
 				as3722_regs->desc[id].min_uV = 610000;
 			}
 			as3722_regs->desc[id].uV_step = 10000;
diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index 62243957bd19..fba8f58ab769 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -367,13 +367,12 @@ static const int axp209_dcdc2_ldo3_slew_rates[] = {
 static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
 {
 	struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
-	const struct regulator_desc *desc = rdev->desc;
+	const struct regulator_desc *desc;
 	u8 reg, mask, enable, cfg = 0xff;
 	const int *slew_rates;
 	int rate_count = 0;
 
-	if (!rdev)
-		return -EINVAL;
+	desc = rdev->desc;
 
 	switch (axp20x->variant) {
 	case AXP209_ID:
@@ -436,11 +435,13 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp)
 static int axp20x_regulator_enable_regmap(struct regulator_dev *rdev)
 {
 	struct axp20x_dev *axp20x = rdev_get_drvdata(rdev);
-	const struct regulator_desc *desc = rdev->desc;
+	const struct regulator_desc *desc;
 
 	if (!rdev)
 		return -EINVAL;
 
+	desc = rdev->desc;
+
 	switch (axp20x->variant) {
 	case AXP209_ID:
 		if ((desc->id == AXP20X_LDO3) &&
diff --git a/drivers/regulator/bd70528-regulator.c b/drivers/regulator/bd70528-regulator.c
new file mode 100644
index 000000000000..30e3ed430a8a
--- /dev/null
+++ b/drivers/regulator/bd70528-regulator.c
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+// bd70528-regulator.c ROHM BD70528MWV regulator driver
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/rohm-bd70528.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/slab.h>
+
+#define BUCK_RAMPRATE_250MV 0
+#define BUCK_RAMPRATE_125MV 1
+#define BUCK_RAMP_MAX 250
+
+static const struct regulator_linear_range bd70528_buck1_volts[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 600000),
+	REGULATOR_LINEAR_RANGE(2750000, 0x2, 0xf, 50000),
+};
+static const struct regulator_linear_range bd70528_buck2_volts[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 300000),
+	REGULATOR_LINEAR_RANGE(1550000, 0x2, 0xd, 50000),
+	REGULATOR_LINEAR_RANGE(3000000, 0xe, 0xf, 300000),
+};
+static const struct regulator_linear_range bd70528_buck3_volts[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0x00, 0xd, 50000),
+	REGULATOR_LINEAR_RANGE(1800000, 0xe, 0xf, 0),
+};
+
+/* All LDOs have same voltage ranges */
+static const struct regulator_linear_range bd70528_ldo_volts[] = {
+	REGULATOR_LINEAR_RANGE(1650000, 0x0, 0x07, 50000),
+	REGULATOR_LINEAR_RANGE(2100000, 0x8, 0x0f, 100000),
+	REGULATOR_LINEAR_RANGE(2850000, 0x10, 0x19, 50000),
+	REGULATOR_LINEAR_RANGE(3300000, 0x19, 0x1f, 0),
+};
+
+/* Also both LEDs support same voltages */
+static const unsigned int led_volts[] = {
+	20000, 30000
+};
+
+static int bd70528_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+	if (ramp_delay > 0 && ramp_delay <= BUCK_RAMP_MAX) {
+		unsigned int ramp_value = BUCK_RAMPRATE_250MV;
+
+		if (ramp_delay <= 125)
+			ramp_value = BUCK_RAMPRATE_125MV;
+
+		return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+				  BD70528_MASK_BUCK_RAMP,
+				  ramp_value << BD70528_SIFT_BUCK_RAMP);
+	}
+	dev_err(&rdev->dev, "%s: ramp_delay: %d not supported\n",
+		rdev->desc->name, ramp_delay);
+	return -EINVAL;
+}
+
+static int bd70528_led_set_voltage_sel(struct regulator_dev *rdev,
+				       unsigned int sel)
+{
+	int ret;
+
+	ret = regulator_is_enabled_regmap(rdev);
+	if (ret < 0)
+		return ret;
+
+	if (ret == 0)
+		return regulator_set_voltage_sel_regmap(rdev, sel);
+
+	dev_err(&rdev->dev,
+		"LED voltage change not allowed when led is enabled\n");
+
+	return -EBUSY;
+}
+
+static const struct regulator_ops bd70528_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = bd70528_set_ramp_delay,
+};
+
+static const struct regulator_ops bd70528_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = bd70528_set_ramp_delay,
+};
+
+static const struct regulator_ops bd70528_led_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = bd70528_led_set_voltage_sel,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_desc bd70528_desc[] = {
+	{
+		.name = "buck1",
+		.of_match = of_match_ptr("BUCK1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_BUCK1,
+		.ops = &bd70528_buck_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_buck1_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_buck1_volts),
+		.n_voltages = BD70528_BUCK_VOLTS,
+		.enable_reg = BD70528_REG_BUCK1_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_BUCK1_VOLT,
+		.vsel_mask = BD70528_MASK_BUCK_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck2",
+		.of_match = of_match_ptr("BUCK2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_BUCK2,
+		.ops = &bd70528_buck_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_buck2_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_buck2_volts),
+		.n_voltages = BD70528_BUCK_VOLTS,
+		.enable_reg = BD70528_REG_BUCK2_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_BUCK2_VOLT,
+		.vsel_mask = BD70528_MASK_BUCK_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck3",
+		.of_match = of_match_ptr("BUCK3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_BUCK3,
+		.ops = &bd70528_buck_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_buck3_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_buck3_volts),
+		.n_voltages = BD70528_BUCK_VOLTS,
+		.enable_reg = BD70528_REG_BUCK3_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_BUCK3_VOLT,
+		.vsel_mask = BD70528_MASK_BUCK_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo1",
+		.of_match = of_match_ptr("LDO1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_LDO1,
+		.ops = &bd70528_ldo_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_ldo_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+		.n_voltages = BD70528_LDO_VOLTS,
+		.enable_reg = BD70528_REG_LDO1_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_LDO1_VOLT,
+		.vsel_mask = BD70528_MASK_LDO_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo2",
+		.of_match = of_match_ptr("LDO2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_LDO2,
+		.ops = &bd70528_ldo_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_ldo_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+		.n_voltages = BD70528_LDO_VOLTS,
+		.enable_reg = BD70528_REG_LDO2_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_LDO2_VOLT,
+		.vsel_mask = BD70528_MASK_LDO_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo3",
+		.of_match = of_match_ptr("LDO3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_LDO3,
+		.ops = &bd70528_ldo_ops,
+		.type = REGULATOR_VOLTAGE,
+		.linear_ranges = bd70528_ldo_volts,
+		.n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts),
+		.n_voltages = BD70528_LDO_VOLTS,
+		.enable_reg = BD70528_REG_LDO3_EN,
+		.enable_mask = BD70528_MASK_RUN_EN,
+		.vsel_reg = BD70528_REG_LDO3_VOLT,
+		.vsel_mask = BD70528_MASK_LDO_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo_led1",
+		.of_match = of_match_ptr("LDO_LED1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_LED1,
+		.ops = &bd70528_led_ops,
+		.type = REGULATOR_VOLTAGE,
+		.volt_table = &led_volts[0],
+		.n_voltages = ARRAY_SIZE(led_volts),
+		.enable_reg = BD70528_REG_LED_EN,
+		.enable_mask = BD70528_MASK_LED1_EN,
+		.vsel_reg = BD70528_REG_LED_VOLT,
+		.vsel_mask = BD70528_MASK_LED1_VOLT,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo_led2",
+		.of_match = of_match_ptr("LDO_LED2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD70528_LED2,
+		.ops = &bd70528_led_ops,
+		.type = REGULATOR_VOLTAGE,
+		.volt_table = &led_volts[0],
+		.n_voltages = ARRAY_SIZE(led_volts),
+		.enable_reg = BD70528_REG_LED_EN,
+		.enable_mask = BD70528_MASK_LED2_EN,
+		.vsel_reg = BD70528_REG_LED_VOLT,
+		.vsel_mask = BD70528_MASK_LED2_VOLT,
+		.owner = THIS_MODULE,
+	},
+
+};
+
+static int bd70528_probe(struct platform_device *pdev)
+{
+	struct rohm_regmap_dev *bd70528;
+	int i;
+	struct regulator_config config = {
+		.dev = pdev->dev.parent,
+	};
+
+	bd70528 = dev_get_drvdata(pdev->dev.parent);
+	if (!bd70528) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		return -EINVAL;
+	}
+
+	config.regmap = bd70528->regmap;
+
+	for (i = 0; i < ARRAY_SIZE(bd70528_desc); i++) {
+		struct regulator_dev *rdev;
+
+		rdev = devm_regulator_register(&pdev->dev, &bd70528_desc[i],
+					       &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&pdev->dev,
+				"failed to register %s regulator\n",
+				bd70528_desc[i].name);
+			return PTR_ERR(rdev);
+		}
+	}
+	return 0;
+}
+
+static struct platform_driver bd70528_regulator = {
+	.driver = {
+		.name = "bd70528-pmic"
+	},
+	.probe = bd70528_probe,
+};
+
+module_platform_driver(bd70528_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD70528 voltage regulator driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index b8dcdc21dc22..b2191be49670 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -79,7 +79,7 @@ static int bd718xx_set_voltage_sel_pickable_restricted(
 	return regulator_set_voltage_sel_pickable_regmap(rdev, sel);
 }
 
-static struct regulator_ops bd718xx_pickable_range_ldo_ops = {
+static const struct regulator_ops bd718xx_pickable_range_ldo_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -88,7 +88,7 @@ static struct regulator_ops bd718xx_pickable_range_ldo_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
 };
 
-static struct regulator_ops bd718xx_pickable_range_buck_ops = {
+static const struct regulator_ops bd718xx_pickable_range_buck_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -98,7 +98,7 @@ static struct regulator_ops bd718xx_pickable_range_buck_ops = {
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 };
 
-static struct regulator_ops bd718xx_ldo_regulator_ops = {
+static const struct regulator_ops bd718xx_ldo_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -107,7 +107,7 @@ static struct regulator_ops bd718xx_ldo_regulator_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 };
 
-static struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
+static const struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -116,7 +116,7 @@ static struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 };
 
-static struct regulator_ops bd718xx_buck_regulator_ops = {
+static const struct regulator_ops bd718xx_buck_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -126,7 +126,7 @@ static struct regulator_ops bd718xx_buck_regulator_ops = {
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 };
 
-static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
+static const struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -137,7 +137,7 @@ static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 };
 
-static struct regulator_ops bd718xx_dvs_buck_regulator_ops = {
+static const struct regulator_ops bd718xx_dvs_buck_regulator_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -350,6 +350,135 @@ static const struct reg_init bd71837_ldo6_inits[] = {
 	},
 };
 
+#define NUM_DVS_BUCKS 4
+
+struct of_dvs_setting {
+	const char *prop;
+	unsigned int reg;
+};
+
+static int set_dvs_levels(const struct of_dvs_setting *dvs,
+			  struct device_node *np,
+			  const struct regulator_desc *desc,
+			  struct regmap *regmap)
+{
+	int ret, i;
+	unsigned int uv;
+
+	ret = of_property_read_u32(np, dvs->prop, &uv);
+	if (ret) {
+		if (ret != -EINVAL)
+			return ret;
+		return 0;
+	}
+
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, dvs->reg,
+						 DVS_BUCK_RUN_MASK, i);
+			break;
+		}
+	}
+	return ret;
+}
+
+static int buck4_set_hw_dvs_levels(struct device_node *np,
+			    const struct regulator_desc *desc,
+			    struct regulator_config *cfg)
+{
+	int ret, i;
+	const struct of_dvs_setting dvs[] = {
+		{
+			.prop = "rohm,dvs-run-voltage",
+			.reg = BD71837_REG_BUCK4_VOLT_RUN,
+		},
+	};
+
+	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
+		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
+		if (ret)
+			break;
+	}
+	return ret;
+}
+static int buck3_set_hw_dvs_levels(struct device_node *np,
+			    const struct regulator_desc *desc,
+			    struct regulator_config *cfg)
+{
+	int ret, i;
+	const struct of_dvs_setting dvs[] = {
+		{
+			.prop = "rohm,dvs-run-voltage",
+			.reg = BD71837_REG_BUCK3_VOLT_RUN,
+		},
+	};
+
+	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
+		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
+		if (ret)
+			break;
+	}
+	return ret;
+}
+
+static int buck2_set_hw_dvs_levels(struct device_node *np,
+			    const struct regulator_desc *desc,
+			    struct regulator_config *cfg)
+{
+	int ret, i;
+	const struct of_dvs_setting dvs[] = {
+		{
+			.prop = "rohm,dvs-run-voltage",
+			.reg = BD718XX_REG_BUCK2_VOLT_RUN,
+		},
+		{
+			.prop = "rohm,dvs-idle-voltage",
+			.reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+		},
+	};
+
+
+
+	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
+		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
+		if (ret)
+			break;
+	}
+	return ret;
+}
+
+static int buck1_set_hw_dvs_levels(struct device_node *np,
+			    const struct regulator_desc *desc,
+			    struct regulator_config *cfg)
+{
+	int ret, i;
+	const struct of_dvs_setting dvs[] = {
+		{
+			.prop = "rohm,dvs-run-voltage",
+			.reg = BD718XX_REG_BUCK1_VOLT_RUN,
+		},
+		{
+			.prop = "rohm,dvs-idle-voltage",
+			.reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+		},
+		{
+			.prop = "rohm,dvs-suspend-voltage",
+			.reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+		},
+	};
+
+	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
+		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
+		if (ret)
+			break;
+	}
+	return ret;
+}
+
 static const struct bd718xx_regulator_data bd71847_regulators[] = {
 	{
 		.desc = {
@@ -368,6 +497,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck1_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -391,6 +521,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck2_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -662,6 +793,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck1_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -685,6 +817,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck2_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -708,6 +841,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK3_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck3_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK3_CTRL,
@@ -731,6 +865,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK4_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
+			.of_parse_cb = buck4_set_hw_dvs_levels,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK4_CTRL,
@@ -1029,6 +1164,7 @@ static int bd718xx_probe(struct platform_device *pdev)
 	};
 
 	int i, j, err;
+	bool use_snvs;
 
 	mfd = dev_get_drvdata(pdev->dev.parent);
 	if (!mfd) {
@@ -1055,27 +1191,28 @@ static int bd718xx_probe(struct platform_device *pdev)
 			BD718XX_REG_REGLOCK);
 	}
 
-	/* At poweroff transition PMIC HW disables EN bit for regulators but
-	 * leaves SEL bit untouched. So if state transition from POWEROFF
-	 * is done to SNVS - then all power rails controlled by SW (having
-	 * SEL bit set) stay disabled as EN is cleared. This may result boot
-	 * failure if any crucial systems are powered by these rails.
-	 *
+	use_snvs = of_property_read_bool(pdev->dev.parent->of_node,
+					 "rohm,reset-snvs-powered");
+
+	/*
 	 * Change the next stage from poweroff to be READY instead of SNVS
 	 * for all reset types because OTP loading at READY will clear SEL
 	 * bit allowing HW defaults for power rails to be used
 	 */
-	err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1,
-				 BD718XX_ON_REQ_POWEROFF_MASK |
-				 BD718XX_SWRESET_POWEROFF_MASK |
-				 BD718XX_WDOG_POWEROFF_MASK |
-				 BD718XX_KEY_L_POWEROFF_MASK,
-				 BD718XX_POWOFF_TO_RDY);
-	if (err) {
-		dev_err(&pdev->dev, "Failed to change reset target\n");
-		goto err;
-	} else {
-		dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n");
+	if (!use_snvs) {
+		err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1,
+					 BD718XX_ON_REQ_POWEROFF_MASK |
+					 BD718XX_SWRESET_POWEROFF_MASK |
+					 BD718XX_WDOG_POWEROFF_MASK |
+					 BD718XX_KEY_L_POWEROFF_MASK,
+					 BD718XX_POWOFF_TO_RDY);
+		if (err) {
+			dev_err(&pdev->dev, "Failed to change reset target\n");
+			goto err;
+		} else {
+			dev_dbg(&pdev->dev,
+				"Changed all resets from SVNS to READY\n");
+		}
 	}
 
 	for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) {
@@ -1098,19 +1235,33 @@ static int bd718xx_probe(struct platform_device *pdev)
 			err = PTR_ERR(rdev);
 			goto err;
 		}
-		/* Regulator register gets the regulator constraints and
+
+		/*
+		 * Regulator register gets the regulator constraints and
 		 * applies them (set_machine_constraints). This should have
 		 * turned the control register(s) to correct values and we
 		 * can now switch the control from PMIC state machine to the
 		 * register interface
+		 *
+		 * At poweroff transition PMIC HW disables EN bit for
+		 * regulators but leaves SEL bit untouched. So if state
+		 * transition from POWEROFF is done to SNVS - then all power
+		 * rails controlled by SW (having SEL bit set) stay disabled
+		 * as EN is cleared. This will result boot failure if any
+		 * crucial systems are powered by these rails. We don't
+		 * enable SW control for crucial regulators if snvs state is
+		 * used
 		 */
-		err = regmap_update_bits(mfd->regmap, r->init.reg,
-					 r->init.mask, r->init.val);
-		if (err) {
-			dev_err(&pdev->dev,
-				"Failed to write BUCK/LDO SEL bit for (%s)\n",
-				desc->name);
-			goto err;
+		if (!use_snvs || !rdev->constraints->always_on ||
+		    !rdev->constraints->boot_on) {
+			err = regmap_update_bits(mfd->regmap, r->init.reg,
+						 r->init.mask, r->init.val);
+			if (err) {
+				dev_err(&pdev->dev,
+					"Failed to take control for (%s)\n",
+					desc->name);
+				goto err;
+			}
 		}
 		for (j = 0; j < r->additional_init_amnt; j++) {
 			err = regmap_update_bits(mfd->regmap,
diff --git a/drivers/regulator/bd9571mwv-regulator.c b/drivers/regulator/bd9571mwv-regulator.c
index e12dd1f750f3..e690c2ce5b3c 100644
--- a/drivers/regulator/bd9571mwv-regulator.c
+++ b/drivers/regulator/bd9571mwv-regulator.c
@@ -100,7 +100,7 @@ static int bd9571mwv_reg_set_voltage_sel_regmap(struct regulator_dev *rdev,
 }
 
 /* Operations permitted on AVS voltage regulator */
-static struct regulator_ops avs_ops = {
+static const struct regulator_ops avs_ops = {
 	.set_voltage_sel	= bd9571mwv_avs_set_voltage_sel_regmap,
 	.map_voltage		= regulator_map_voltage_linear,
 	.get_voltage_sel	= bd9571mwv_avs_get_voltage_sel_regmap,
@@ -108,7 +108,7 @@ static struct regulator_ops avs_ops = {
 };
 
 /* Operations permitted on voltage regulators */
-static struct regulator_ops reg_ops = {
+static const struct regulator_ops reg_ops = {
 	.set_voltage_sel	= bd9571mwv_reg_set_voltage_sel_regmap,
 	.map_voltage		= regulator_map_voltage_linear,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
@@ -116,13 +116,13 @@ static struct regulator_ops reg_ops = {
 };
 
 /* Operations permitted on voltage monitors */
-static struct regulator_ops vid_ops = {
+static const struct regulator_ops vid_ops = {
 	.map_voltage		= regulator_map_voltage_linear,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.list_voltage		= regulator_list_voltage_linear,
 };
 
-static struct regulator_desc regulators[] = {
+static const struct regulator_desc regulators[] = {
 	BD9571MWV_REG("VD09", "vd09", VD09, avs_ops, 0, 0x7f,
 		      0x80, 600000, 10000, 0x3c),
 	BD9571MWV_REG("VD18", "vd18", VD18, vid_ops, BD9571MWV_VD18_VID, 0xf,
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 19b35d9f3a97..68473d0cc57e 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -23,7 +23,6 @@
 #include <linux/mutex.h>
 #include <linux/suspend.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
 #include <linux/of.h>
 #include <linux/regmap.h>
@@ -82,7 +81,6 @@ struct regulator_enable_gpio {
 	struct gpio_desc *gpiod;
 	u32 enable_count;	/* a number of enabled shared GPIO */
 	u32 request_count;	/* a number of requested shared GPIO */
-	unsigned int ena_gpio_invert:1;
 };
 
 /*
@@ -145,14 +143,6 @@ static bool regulator_ops_is_valid(struct regulator_dev *rdev, int ops)
 	return false;
 }
 
-static inline struct regulator_dev *rdev_get_supply(struct regulator_dev *rdev)
-{
-	if (rdev && rdev->supply)
-		return rdev->supply->rdev;
-
-	return NULL;
-}
-
 /**
  * regulator_lock_nested - lock a single regulator
  * @rdev:		regulator source
@@ -326,7 +316,7 @@ err_unlock:
  * @rdev:			regulator source
  * @ww_ctx:			w/w mutex acquire context
  *
- * Unlock all regulators related with rdev by coupling or suppling.
+ * Unlock all regulators related with rdev by coupling or supplying.
  */
 static void regulator_unlock_dependent(struct regulator_dev *rdev,
 				       struct ww_acquire_ctx *ww_ctx)
@@ -341,7 +331,7 @@ static void regulator_unlock_dependent(struct regulator_dev *rdev,
  * @ww_ctx:			w/w mutex acquire context
  *
  * This function as a wrapper on regulator_lock_recursive(), which locks
- * all regulators related with rdev by coupling or suppling.
+ * all regulators related with rdev by coupling or supplying.
  */
 static void regulator_lock_dependent(struct regulator_dev *rdev,
 				     struct ww_acquire_ctx *ww_ctx)
@@ -924,14 +914,14 @@ static int drms_uA_update(struct regulator_dev *rdev)
 	int current_uA = 0, output_uV, input_uV, err;
 	unsigned int mode;
 
-	lockdep_assert_held_once(&rdev->mutex.base);
-
 	/*
 	 * first check to see if we can set modes at all, otherwise just
 	 * tell the consumer everything is OK.
 	 */
-	if (!regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS))
+	if (!regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS)) {
+		rdev_dbg(rdev, "DRMS operation not allowed\n");
 		return 0;
+	}
 
 	if (!rdev->desc->ops->get_optimum_mode &&
 	    !rdev->desc->ops->set_load)
@@ -1003,7 +993,7 @@ static int suspend_set_state(struct regulator_dev *rdev,
 	if (rstate == NULL)
 		return 0;
 
-	/* If we have no suspend mode configration don't set anything;
+	/* If we have no suspend mode configuration don't set anything;
 	 * only warn if the driver implements set_suspend_voltage or
 	 * set_suspend_mode callback.
 	 */
@@ -1131,7 +1121,7 @@ static int machine_constraints_voltage(struct regulator_dev *rdev,
 		int current_uV = _regulator_get_voltage(rdev);
 
 		if (current_uV == -ENOTRECOVERABLE) {
-			/* This regulator can't be read and must be initted */
+			/* This regulator can't be read and must be initialized */
 			rdev_info(rdev, "Setting %d-%duV\n",
 				  rdev->constraints->min_uV,
 				  rdev->constraints->max_uV);
@@ -1782,7 +1772,7 @@ static int regulator_resolve_supply(struct regulator_dev *rdev)
 	struct device *dev = rdev->dev.parent;
 	int ret;
 
-	/* No supply to resovle? */
+	/* No supply to resolve? */
 	if (!rdev->supply_name)
 		return 0;
 
@@ -2231,38 +2221,21 @@ static int regulator_ena_gpio_request(struct regulator_dev *rdev,
 {
 	struct regulator_enable_gpio *pin;
 	struct gpio_desc *gpiod;
-	int ret;
 
-	if (config->ena_gpiod)
-		gpiod = config->ena_gpiod;
-	else
-		gpiod = gpio_to_desc(config->ena_gpio);
+	gpiod = config->ena_gpiod;
 
 	list_for_each_entry(pin, &regulator_ena_gpio_list, list) {
 		if (pin->gpiod == gpiod) {
-			rdev_dbg(rdev, "GPIO %d is already used\n",
-				config->ena_gpio);
+			rdev_dbg(rdev, "GPIO is already used\n");
 			goto update_ena_gpio_to_rdev;
 		}
 	}
 
-	if (!config->ena_gpiod) {
-		ret = gpio_request_one(config->ena_gpio,
-				       GPIOF_DIR_OUT | config->ena_gpio_flags,
-				       rdev_get_name(rdev));
-		if (ret)
-			return ret;
-	}
-
 	pin = kzalloc(sizeof(struct regulator_enable_gpio), GFP_KERNEL);
-	if (pin == NULL) {
-		if (!config->ena_gpiod)
-			gpio_free(config->ena_gpio);
+	if (pin == NULL)
 		return -ENOMEM;
-	}
 
 	pin->gpiod = gpiod;
-	pin->ena_gpio_invert = config->ena_gpio_invert;
 	list_add(&pin->list, &regulator_ena_gpio_list);
 
 update_ena_gpio_to_rdev:
@@ -2283,7 +2256,6 @@ static void regulator_ena_gpio_free(struct regulator_dev *rdev)
 		if (pin->gpiod == rdev->ena_pin->gpiod) {
 			if (pin->request_count <= 1) {
 				pin->request_count = 0;
-				gpiod_put(pin->gpiod);
 				list_del(&pin->list);
 				kfree(pin);
 				rdev->ena_pin = NULL;
@@ -2313,8 +2285,7 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable)
 	if (enable) {
 		/* Enable GPIO at initial use */
 		if (pin->enable_count == 0)
-			gpiod_set_value_cansleep(pin->gpiod,
-						 !pin->ena_gpio_invert);
+			gpiod_set_value_cansleep(pin->gpiod, 1);
 
 		pin->enable_count++;
 	} else {
@@ -2325,8 +2296,7 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable)
 
 		/* Disable GPIO if not used */
 		if (pin->enable_count <= 1) {
-			gpiod_set_value_cansleep(pin->gpiod,
-						 pin->ena_gpio_invert);
+			gpiod_set_value_cansleep(pin->gpiod, 0);
 			pin->enable_count = 0;
 		}
 	}
@@ -2403,7 +2373,7 @@ static int _regulator_do_enable(struct regulator_dev *rdev)
 			 * timer wrapping.
 			 * in case of multiple timer wrapping, either it can be
 			 * detected by out-of-range remaining, or it cannot be
-			 * detected and we gets a panelty of
+			 * detected and we get a penalty of
 			 * _regulator_enable_delay().
 			 */
 			remaining = intended - start_jiffy;
@@ -2803,7 +2773,7 @@ static void regulator_disable_work(struct work_struct *work)
 /**
  * regulator_disable_deferred - disable regulator output with delay
  * @regulator: regulator source
- * @ms: miliseconds until the regulator is disabled
+ * @ms: milliseconds until the regulator is disabled
  *
  * Execute regulator_disable() on the regulator after a delay.  This
  * is intended for use with devices that require some time to quiesce.
@@ -4937,7 +4907,7 @@ regulator_register(const struct regulator_desc *regulator_desc,
 	 * device tree until we have handled it over to the core. If the
 	 * config that was passed in to this function DOES NOT contain
 	 * a descriptor, and the config after this call DOES contain
-	 * a descriptor, we definately got one from parsing the device
+	 * a descriptor, we definitely got one from parsing the device
 	 * tree.
 	 */
 	if (!cfg->ena_gpiod && config->ena_gpiod)
@@ -4969,15 +4939,13 @@ regulator_register(const struct regulator_desc *regulator_desc,
 			goto clean;
 	}
 
-	if (config->ena_gpiod ||
-	    ((config->ena_gpio || config->ena_gpio_initialized) &&
-	     gpio_is_valid(config->ena_gpio))) {
+	if (config->ena_gpiod) {
 		mutex_lock(&regulator_list_mutex);
 		ret = regulator_ena_gpio_request(rdev, config);
 		mutex_unlock(&regulator_list_mutex);
 		if (ret != 0) {
-			rdev_err(rdev, "Failed to request enable GPIO%d: %d\n",
-				 config->ena_gpio, ret);
+			rdev_err(rdev, "Failed to request enable GPIO: %d\n",
+				 ret);
 			goto clean;
 		}
 		/* The regulator core took over the GPIO descriptor */
@@ -5245,6 +5213,12 @@ struct device *rdev_get_dev(struct regulator_dev *rdev)
 }
 EXPORT_SYMBOL_GPL(rdev_get_dev);
 
+struct regmap *rdev_get_regmap(struct regulator_dev *rdev)
+{
+	return rdev->regmap;
+}
+EXPORT_SYMBOL_GPL(rdev_get_regmap);
+
 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data)
 {
 	return reg_init_data->driver_data;
diff --git a/drivers/regulator/cpcap-regulator.c b/drivers/regulator/cpcap-regulator.c
index 2131457937b7..e7dab5c4d1d1 100644
--- a/drivers/regulator/cpcap-regulator.c
+++ b/drivers/regulator/cpcap-regulator.c
@@ -100,12 +100,11 @@ struct cpcap_regulator {
 	struct regulator_desc rdesc;
 	const u16 assign_reg;
 	const u16 assign_mask;
-	const u16 vsel_shift;
 };
 
 #define CPCAP_REG(_ID, reg, assignment_reg, assignment_mask, val_tbl,	\
-		mode_mask, volt_mask, volt_shft,			\
-		mode_val, off_val, volt_trans_time) {			\
+		mode_mask, volt_mask, mode_val, off_val,		\
+		volt_trans_time) {					\
 	.rdesc = {							\
 		.name = #_ID,						\
 		.of_match = of_match_ptr(#_ID),				\
@@ -127,7 +126,6 @@ struct cpcap_regulator {
 	},								\
 	.assign_reg = (assignment_reg),					\
 	.assign_mask = (assignment_mask),				\
-	.vsel_shift = (volt_shft),					\
 }
 
 struct cpcap_ddata {
@@ -336,155 +334,155 @@ static const unsigned int vaudio_val_tbl[] = { 0, 2775000, };
  * SW1 to SW4 and SW6 seems to be unused for mapphone. Note that VSIM and
  * VSIMCARD have a shared resource assignment bit.
  */
-static struct cpcap_regulator omap4_regulators[] = {
+static const struct cpcap_regulator omap4_regulators[] = {
 	CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW1_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW2_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW3_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW4_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW5, CPCAP_REG_S5C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW5_SEL, sw5_val_tbl,
-		  0x28, 0, 0, 0x20 | CPCAP_REG_OFF_MODE_SEC, 0, 0),
+		  0x28, 0, 0x20 | CPCAP_REG_OFF_MODE_SEC, 0, 0),
 	CPCAP_REG(SW6, CPCAP_REG_S6C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW6_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(VCAM, CPCAP_REG_VCAMC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VCAM_SEL, vcam_val_tbl,
-		  0x87, 0x30, 4, 0x3, 0, 420),
+		  0x87, 0x30, 0x3, 0, 420),
 	CPCAP_REG(VCSI, CPCAP_REG_VCSIC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VCSI_SEL, vcsi_val_tbl,
-		  0x47, 0x10, 4, 0x43, 0x41, 350),
+		  0x47, 0x10, 0x43, 0x41, 350),
 	CPCAP_REG(VDAC, CPCAP_REG_VDACC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VDAC_SEL, vdac_val_tbl,
-		  0x87, 0x30, 4, 0x3, 0, 420),
+		  0x87, 0x30, 0x3, 0, 420),
 	CPCAP_REG(VDIG, CPCAP_REG_VDIGC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VDIG_SEL, vdig_val_tbl,
-		  0x87, 0x30, 4, 0x82, 0, 420),
+		  0x87, 0x30, 0x82, 0, 420),
 	CPCAP_REG(VFUSE, CPCAP_REG_VFUSEC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VFUSE_SEL, vfuse_val_tbl,
-		  0x80, 0xf, 0, 0x80, 0, 420),
+		  0x80, 0xf, 0x80, 0, 420),
 	CPCAP_REG(VHVIO, CPCAP_REG_VHVIOC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VHVIO_SEL, vhvio_val_tbl,
-		  0x17, 0, 0, 0, 0x12, 0),
+		  0x17, 0, 0, 0x12, 0),
 	CPCAP_REG(VSDIO, CPCAP_REG_VSDIOC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VSDIO_SEL, vsdio_val_tbl,
-		  0x87, 0x38, 3, 0x82, 0, 420),
+		  0x87, 0x38, 0x82, 0, 420),
 	CPCAP_REG(VPLL, CPCAP_REG_VPLLC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VPLL_SEL, vpll_val_tbl,
-		  0x43, 0x18, 3, 0x2, 0, 420),
+		  0x43, 0x18, 0x2, 0, 420),
 	CPCAP_REG(VRF1, CPCAP_REG_VRF1C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRF1_SEL, vrf1_val_tbl,
-		  0xac, 0x2, 1, 0x4, 0, 10),
+		  0xac, 0x2, 0x4, 0, 10),
 	CPCAP_REG(VRF2, CPCAP_REG_VRF2C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRF2_SEL, vrf2_val_tbl,
-		  0x23, 0x8, 3, 0, 0, 10),
+		  0x23, 0x8, 0, 0, 10),
 	CPCAP_REG(VRFREF, CPCAP_REG_VRFREFC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRFREF_SEL, vrfref_val_tbl,
-		  0x23, 0x8, 3, 0, 0, 420),
+		  0x23, 0x8, 0, 0, 420),
 	CPCAP_REG(VWLAN1, CPCAP_REG_VWLAN1C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VWLAN1_SEL, vwlan1_val_tbl,
-		  0x47, 0x10, 4, 0, 0, 420),
+		  0x47, 0x10, 0, 0, 420),
 	CPCAP_REG(VWLAN2, CPCAP_REG_VWLAN2C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VWLAN2_SEL, vwlan2_val_tbl,
-		  0x20c, 0xc0, 6, 0x20c, 0, 420),
+		  0x20c, 0xc0, 0x20c, 0, 420),
 	CPCAP_REG(VSIM, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3,
 		  0xffff, vsim_val_tbl,
-		  0x23, 0x8, 3, 0x3, 0, 420),
+		  0x23, 0x8, 0x3, 0, 420),
 	CPCAP_REG(VSIMCARD, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3,
 		  0xffff, vsimcard_val_tbl,
-		  0x1e80, 0x8, 3, 0x1e00, 0, 420),
+		  0x1e80, 0x8, 0x1e00, 0, 420),
 	CPCAP_REG(VVIB, CPCAP_REG_VVIBC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VVIB_SEL, vvib_val_tbl,
-		  0x1, 0xc, 2, 0x1, 0, 500),
+		  0x1, 0xc, 0x1, 0, 500),
 	CPCAP_REG(VUSB, CPCAP_REG_VUSBC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VUSB_SEL, vusb_val_tbl,
-		  0x11c, 0x40, 6, 0xc, 0, 0),
+		  0x11c, 0x40, 0xc, 0, 0),
 	CPCAP_REG(VAUDIO, CPCAP_REG_VAUDIOC, CPCAP_REG_ASSIGN4,
 		  CPCAP_BIT_VAUDIO_SEL, vaudio_val_tbl,
-		  0x16, 0x1, 0, 0x4, 0, 0),
+		  0x16, 0x1, 0x4, 0, 0),
 	{ /* sentinel */ },
 };
 
-static struct cpcap_regulator xoom_regulators[] = {
+static const struct cpcap_regulator xoom_regulators[] = {
 	CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW1_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW2_SEL, sw2_sw4_val_tbl,
-		  0xf00, 0x7f, 0, 0x800, 0, 120),
+		  0xf00, 0x7f, 0x800, 0, 120),
 	CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW3_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW4_SEL, sw2_sw4_val_tbl,
-		  0xf00, 0x7f, 0, 0x900, 0, 100),
+		  0xf00, 0x7f, 0x900, 0, 100),
 	CPCAP_REG(SW5, CPCAP_REG_S5C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW5_SEL, sw5_val_tbl,
-		  0x2a, 0, 0, 0x22, 0, 0),
+		  0x2a, 0, 0x22, 0, 0),
 	CPCAP_REG(SW6, CPCAP_REG_S6C, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_SW6_SEL, unknown_val_tbl,
-		  0, 0, 0, 0, 0, 0),
+		  0, 0, 0, 0, 0),
 	CPCAP_REG(VCAM, CPCAP_REG_VCAMC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VCAM_SEL, vcam_val_tbl,
-		  0x87, 0x30, 4, 0x7, 0, 420),
+		  0x87, 0x30, 0x7, 0, 420),
 	CPCAP_REG(VCSI, CPCAP_REG_VCSIC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VCSI_SEL, vcsi_val_tbl,
-		  0x47, 0x10, 4, 0x7, 0, 350),
+		  0x47, 0x10, 0x7, 0, 350),
 	CPCAP_REG(VDAC, CPCAP_REG_VDACC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VDAC_SEL, vdac_val_tbl,
-		  0x87, 0x30, 4, 0x3, 0, 420),
+		  0x87, 0x30, 0x3, 0, 420),
 	CPCAP_REG(VDIG, CPCAP_REG_VDIGC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VDIG_SEL, vdig_val_tbl,
-		  0x87, 0x30, 4, 0x5, 0, 420),
+		  0x87, 0x30, 0x5, 0, 420),
 	CPCAP_REG(VFUSE, CPCAP_REG_VFUSEC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VFUSE_SEL, vfuse_val_tbl,
-		  0x80, 0xf, 0, 0x80, 0, 420),
+		  0x80, 0xf, 0x80, 0, 420),
 	CPCAP_REG(VHVIO, CPCAP_REG_VHVIOC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VHVIO_SEL, vhvio_val_tbl,
-		  0x17, 0, 0, 0x2, 0, 0),
+		  0x17, 0, 0x2, 0, 0),
 	CPCAP_REG(VSDIO, CPCAP_REG_VSDIOC, CPCAP_REG_ASSIGN2,
 		  CPCAP_BIT_VSDIO_SEL, vsdio_val_tbl,
-		  0x87, 0x38, 3, 0x2, 0, 420),
+		  0x87, 0x38, 0x2, 0, 420),
 	CPCAP_REG(VPLL, CPCAP_REG_VPLLC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VPLL_SEL, vpll_val_tbl,
-		  0x43, 0x18, 3, 0x1, 0, 420),
+		  0x43, 0x18, 0x1, 0, 420),
 	CPCAP_REG(VRF1, CPCAP_REG_VRF1C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRF1_SEL, vrf1_val_tbl,
-		  0xac, 0x2, 1, 0xc, 0, 10),
+		  0xac, 0x2, 0xc, 0, 10),
 	CPCAP_REG(VRF2, CPCAP_REG_VRF2C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRF2_SEL, vrf2_val_tbl,
-		  0x23, 0x8, 3, 0x3, 0, 10),
+		  0x23, 0x8, 0x3, 0, 10),
 	CPCAP_REG(VRFREF, CPCAP_REG_VRFREFC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VRFREF_SEL, vrfref_val_tbl,
-		  0x23, 0x8, 3, 0x3, 0, 420),
+		  0x23, 0x8, 0x3, 0, 420),
 	CPCAP_REG(VWLAN1, CPCAP_REG_VWLAN1C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VWLAN1_SEL, vwlan1_val_tbl,
-		  0x47, 0x10, 4, 0x5, 0, 420),
+		  0x47, 0x10, 0x5, 0, 420),
 	CPCAP_REG(VWLAN2, CPCAP_REG_VWLAN2C, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VWLAN2_SEL, vwlan2_val_tbl,
-		  0x20c, 0xc0, 6, 0x8, 0, 420),
+		  0x20c, 0xc0, 0x8, 0, 420),
 	CPCAP_REG(VSIM, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3,
 		  0xffff, vsim_val_tbl,
-		  0x23, 0x8, 3, 0x3, 0, 420),
+		  0x23, 0x8, 0x3, 0, 420),
 	CPCAP_REG(VSIMCARD, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3,
 		  0xffff, vsimcard_val_tbl,
-		  0x1e80, 0x8, 3, 0x1e00, 0, 420),
+		  0x1e80, 0x8, 0x1e00, 0, 420),
 	CPCAP_REG(VVIB, CPCAP_REG_VVIBC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VVIB_SEL, vvib_val_tbl,
-		  0x1, 0xc, 2, 0, 0x1, 500),
+		  0x1, 0xc, 0, 0x1, 500),
 	CPCAP_REG(VUSB, CPCAP_REG_VUSBC, CPCAP_REG_ASSIGN3,
 		  CPCAP_BIT_VUSB_SEL, vusb_val_tbl,
-		  0x11c, 0x40, 6, 0xc, 0, 0),
+		  0x11c, 0x40, 0xc, 0, 0),
 	CPCAP_REG(VAUDIO, CPCAP_REG_VAUDIOC, CPCAP_REG_ASSIGN4,
 		  CPCAP_BIT_VAUDIO_SEL, vaudio_val_tbl,
-		  0x16, 0x1, 0, 0x4, 0, 0),
+		  0x16, 0x1, 0x4, 0, 0),
 	{ /* sentinel */ },
 };
 
diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c
index 588c3d2445cf..3c6fac793658 100644
--- a/drivers/regulator/da9055-regulator.c
+++ b/drivers/regulator/da9055-regulator.c
@@ -48,7 +48,9 @@
 #define DA9055_ID_LDO6		7
 
 /* DA9055 BUCK current limit */
-static const int da9055_current_limits[] = { 500000, 600000, 700000, 800000 };
+static const unsigned int da9055_current_limits[] = {
+	500000, 600000, 700000, 800000
+};
 
 struct da9055_conf_reg {
 	int reg;
@@ -169,39 +171,6 @@ static int da9055_ldo_set_mode(struct regulator_dev *rdev, unsigned int mode)
 				 val << volt.sl_shift);
 }
 
-static int da9055_buck_get_current_limit(struct regulator_dev *rdev)
-{
-	struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
-	struct da9055_regulator_info *info = regulator->info;
-	int ret;
-
-	ret = da9055_reg_read(regulator->da9055, DA9055_REG_BUCK_LIM);
-	if (ret < 0)
-		return ret;
-
-	ret &= info->mode.mask;
-	return da9055_current_limits[ret >> info->mode.shift];
-}
-
-static int da9055_buck_set_current_limit(struct regulator_dev *rdev, int min_uA,
-					 int max_uA)
-{
-	struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
-	struct da9055_regulator_info *info = regulator->info;
-	int i;
-
-	for (i = ARRAY_SIZE(da9055_current_limits) - 1; i >= 0; i--) {
-		if ((min_uA <= da9055_current_limits[i]) &&
-		    (da9055_current_limits[i] <= max_uA))
-			return da9055_reg_update(regulator->da9055,
-						 DA9055_REG_BUCK_LIM,
-						 info->mode.mask,
-						 i << info->mode.shift);
-	}
-
-	return -EINVAL;
-}
-
 static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev)
 {
 	struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
@@ -329,8 +298,8 @@ static const struct regulator_ops da9055_buck_ops = {
 	.get_mode = da9055_buck_get_mode,
 	.set_mode = da9055_buck_set_mode,
 
-	.get_current_limit = da9055_buck_get_current_limit,
-	.set_current_limit = da9055_buck_set_current_limit,
+	.get_current_limit = regulator_get_current_limit_regmap,
+	.set_current_limit = regulator_set_current_limit_regmap,
 
 	.get_voltage_sel = da9055_regulator_get_voltage_sel,
 	.set_voltage_sel = da9055_regulator_set_voltage_sel,
@@ -407,6 +376,10 @@ static const struct regulator_ops da9055_ldo_ops = {
 		.uV_step = (step) * 1000,\
 		.linear_min_sel = (voffset),\
 		.owner = THIS_MODULE,\
+		.curr_table = da9055_current_limits,\
+		.n_current_limits = ARRAY_SIZE(da9055_current_limits),\
+		.csel_reg = DA9055_REG_BUCK_LIM,\
+		.csel_mask = (mbits),\
 	},\
 	.conf = {\
 		.reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \
@@ -457,7 +430,6 @@ static int da9055_gpio_init(struct da9055_regulator *regulator,
 		int gpio_mux = pdata->gpio_ren[id];
 
 		config->ena_gpiod = pdata->ena_gpiods[id];
-		config->ena_gpio_invert = 1;
 
 		/*
 		 * GPI pin is muxed with regulator to control the
diff --git a/drivers/regulator/da9062-regulator.c b/drivers/regulator/da9062-regulator.c
index 34a70d9dc450..b064d8a19d4c 100644
--- a/drivers/regulator/da9062-regulator.c
+++ b/drivers/regulator/da9062-regulator.c
@@ -126,7 +126,7 @@ static int da9062_set_current_limit(struct regulator_dev *rdev,
 	const struct da9062_regulator_info *rinfo = regl->info;
 	int n, tval;
 
-	for (n = 0; n < rinfo->n_current_limits; n++) {
+	for (n = rinfo->n_current_limits - 1; n >= 0; n--) {
 		tval = rinfo->current_limits[n];
 		if (tval >= min_ua && tval <= max_ua)
 			return regmap_field_write(regl->ilimit, n);
@@ -992,7 +992,6 @@ static int da9062_regulator_probe(struct platform_device *pdev)
 	struct regulator_config config = { };
 	const struct da9062_regulator_info *rinfo;
 	int irq, n, ret;
-	size_t size;
 	int max_regulators;
 
 	switch (chip->chip_type) {
@@ -1010,9 +1009,8 @@ static int da9062_regulator_probe(struct platform_device *pdev)
 	}
 
 	/* Allocate memory required by usable regulators */
-	size = sizeof(struct da9062_regulators) +
-		max_regulators * sizeof(struct da9062_regulator);
-	regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	regulators = devm_kzalloc(&pdev->dev, struct_size(regulators, regulator,
+				  max_regulators), GFP_KERNEL);
 	if (!regulators)
 		return -ENOMEM;
 
@@ -1029,31 +1027,50 @@ static int da9062_regulator_probe(struct platform_device *pdev)
 		regl->desc.type = REGULATOR_VOLTAGE;
 		regl->desc.owner = THIS_MODULE;
 
-		if (regl->info->mode.reg)
+		if (regl->info->mode.reg) {
 			regl->mode = devm_regmap_field_alloc(
 					&pdev->dev,
 					chip->regmap,
 					regl->info->mode);
-		if (regl->info->suspend.reg)
+			if (IS_ERR(regl->mode))
+				return PTR_ERR(regl->mode);
+		}
+
+		if (regl->info->suspend.reg) {
 			regl->suspend = devm_regmap_field_alloc(
 					&pdev->dev,
 					chip->regmap,
 					regl->info->suspend);
-		if (regl->info->sleep.reg)
+			if (IS_ERR(regl->suspend))
+				return PTR_ERR(regl->suspend);
+		}
+
+		if (regl->info->sleep.reg) {
 			regl->sleep = devm_regmap_field_alloc(
 					&pdev->dev,
 					chip->regmap,
 					regl->info->sleep);
-		if (regl->info->suspend_sleep.reg)
+			if (IS_ERR(regl->sleep))
+				return PTR_ERR(regl->sleep);
+		}
+
+		if (regl->info->suspend_sleep.reg) {
 			regl->suspend_sleep = devm_regmap_field_alloc(
 					&pdev->dev,
 					chip->regmap,
 					regl->info->suspend_sleep);
-		if (regl->info->ilimit.reg)
+			if (IS_ERR(regl->suspend_sleep))
+				return PTR_ERR(regl->suspend_sleep);
+		}
+
+		if (regl->info->ilimit.reg) {
 			regl->ilimit = devm_regmap_field_alloc(
 					&pdev->dev,
 					chip->regmap,
 					regl->info->ilimit);
+			if (IS_ERR(regl->ilimit))
+				return PTR_ERR(regl->ilimit);
+		}
 
 		/* Register regulator */
 		memset(&config, 0, sizeof(config));
diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c
index 8cbcd2a3eb20..2b0c7a85306a 100644
--- a/drivers/regulator/da9063-regulator.c
+++ b/drivers/regulator/da9063-regulator.c
@@ -167,7 +167,7 @@ static int da9063_set_current_limit(struct regulator_dev *rdev,
 	const struct da9063_regulator_info *rinfo = regl->info;
 	int n, tval;
 
-	for (n = 0; n < rinfo->n_current_limits; n++) {
+	for (n = rinfo->n_current_limits - 1; n >= 0; n--) {
 		tval = rinfo->current_limits[n];
 		if (tval >= min_uA && tval <= max_uA)
 			return regmap_field_write(regl->ilimit, n);
@@ -739,7 +739,6 @@ static int da9063_regulator_probe(struct platform_device *pdev)
 	struct regulator_config config;
 	bool bcores_merged, bmem_bio_merged;
 	int id, irq, n, n_regulators, ret, val;
-	size_t size;
 
 	regl_pdata = da9063_pdata ? da9063_pdata->regulators_pdata : NULL;
 
@@ -784,9 +783,8 @@ static int da9063_regulator_probe(struct platform_device *pdev)
 		n_regulators--;    /* remove BMEM_BIO_MERGED */
 
 	/* Allocate memory required by usable regulators */
-	size = sizeof(struct da9063_regulators) +
-		n_regulators * sizeof(struct da9063_regulator);
-	regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	regulators = devm_kzalloc(&pdev->dev, struct_size(regulators,
+				  regulator, n_regulators), GFP_KERNEL);
 	if (!regulators)
 		return -ENOMEM;
 
@@ -835,21 +833,40 @@ static int da9063_regulator_probe(struct platform_device *pdev)
 		regl->desc.type = REGULATOR_VOLTAGE;
 		regl->desc.owner = THIS_MODULE;
 
-		if (regl->info->mode.reg)
+		if (regl->info->mode.reg) {
 			regl->mode = devm_regmap_field_alloc(&pdev->dev,
 					da9063->regmap, regl->info->mode);
-		if (regl->info->suspend.reg)
+			if (IS_ERR(regl->mode))
+				return PTR_ERR(regl->mode);
+		}
+
+		if (regl->info->suspend.reg) {
 			regl->suspend = devm_regmap_field_alloc(&pdev->dev,
 					da9063->regmap, regl->info->suspend);
-		if (regl->info->sleep.reg)
+			if (IS_ERR(regl->suspend))
+				return PTR_ERR(regl->suspend);
+		}
+
+		if (regl->info->sleep.reg) {
 			regl->sleep = devm_regmap_field_alloc(&pdev->dev,
 					da9063->regmap, regl->info->sleep);
-		if (regl->info->suspend_sleep.reg)
+			if (IS_ERR(regl->sleep))
+				return PTR_ERR(regl->sleep);
+		}
+
+		if (regl->info->suspend_sleep.reg) {
 			regl->suspend_sleep = devm_regmap_field_alloc(&pdev->dev,
 					da9063->regmap, regl->info->suspend_sleep);
-		if (regl->info->ilimit.reg)
+			if (IS_ERR(regl->suspend_sleep))
+				return PTR_ERR(regl->suspend_sleep);
+		}
+
+		if (regl->info->ilimit.reg) {
 			regl->ilimit = devm_regmap_field_alloc(&pdev->dev,
 					da9063->regmap, regl->info->ilimit);
+			if (IS_ERR(regl->ilimit))
+				return PTR_ERR(regl->ilimit);
+		}
 
 		/* Register regulator */
 		memset(&config, 0, sizeof(config));
diff --git a/drivers/regulator/da9210-regulator.c b/drivers/regulator/da9210-regulator.c
index 84dba64ed11e..528303771723 100644
--- a/drivers/regulator/da9210-regulator.c
+++ b/drivers/regulator/da9210-regulator.c
@@ -41,10 +41,6 @@ static const struct regmap_config da9210_regmap_config = {
 	.val_bits = 8,
 };
 
-static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA,
-				    int max_uA);
-static int da9210_get_current_limit(struct regulator_dev *rdev);
-
 static const struct regulator_ops da9210_buck_ops = {
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -52,8 +48,8 @@ static const struct regulator_ops da9210_buck_ops = {
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.list_voltage = regulator_list_voltage_linear,
-	.set_current_limit = da9210_set_current_limit,
-	.get_current_limit = da9210_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 };
 
 /* Default limits measured in millivolts and milliamps */
@@ -62,7 +58,7 @@ static const struct regulator_ops da9210_buck_ops = {
 #define DA9210_STEP_MV		10
 
 /* Current limits for buck (uA) indices corresponds with register values */
-static const int da9210_buck_limits[] = {
+static const unsigned int da9210_buck_limits[] = {
 	1600000, 1800000, 2000000, 2200000, 2400000, 2600000, 2800000, 3000000,
 	3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, 4600000
 };
@@ -80,47 +76,12 @@ static const struct regulator_desc da9210_reg = {
 	.enable_reg = DA9210_REG_BUCK_CONT,
 	.enable_mask = DA9210_BUCK_EN,
 	.owner = THIS_MODULE,
+	.curr_table = da9210_buck_limits,
+	.n_current_limits = ARRAY_SIZE(da9210_buck_limits),
+	.csel_reg = DA9210_REG_BUCK_ILIM,
+	.csel_mask = DA9210_BUCK_ILIM_MASK,
 };
 
-static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA,
-				    int max_uA)
-{
-	struct da9210 *chip = rdev_get_drvdata(rdev);
-	unsigned int sel;
-	int i;
-
-	/* search for closest to maximum */
-	for (i = ARRAY_SIZE(da9210_buck_limits)-1; i >= 0; i--) {
-		if (min_uA <= da9210_buck_limits[i] &&
-		    max_uA >= da9210_buck_limits[i]) {
-			sel = i;
-			sel = sel << DA9210_BUCK_ILIM_SHIFT;
-			return regmap_update_bits(chip->regmap,
-						  DA9210_REG_BUCK_ILIM,
-						  DA9210_BUCK_ILIM_MASK, sel);
-		}
-	}
-
-	return -EINVAL;
-}
-
-static int da9210_get_current_limit(struct regulator_dev *rdev)
-{
-	struct da9210 *chip = rdev_get_drvdata(rdev);
-	unsigned int data;
-	unsigned int sel;
-	int ret;
-
-	ret = regmap_read(chip->regmap, DA9210_REG_BUCK_ILIM, &data);
-	if (ret < 0)
-		return ret;
-
-	/* select one of 16 values: 0000 (1600mA) to 1111 (4600mA) */
-	sel = (data & DA9210_BUCK_ILIM_MASK) >> DA9210_BUCK_ILIM_SHIFT;
-
-	return da9210_buck_limits[sel];
-}
-
 static irqreturn_t da9210_irq_handler(int irq, void *data)
 {
 	struct da9210 *chip = data;
diff --git a/drivers/regulator/fan53555.c b/drivers/regulator/fan53555.c
index a3bc8037153e..771a06d1900d 100644
--- a/drivers/regulator/fan53555.c
+++ b/drivers/regulator/fan53555.c
@@ -40,7 +40,6 @@
 /* VSEL bit definitions */
 #define VSEL_BUCK_EN	(1 << 7)
 #define VSEL_MODE		(1 << 6)
-#define VSEL_NSEL_MASK	0x3F
 /* Chip ID and Verison */
 #define DIE_ID		0x0F	/* ID1 */
 #define DIE_REV		0x0F	/* ID2 */
@@ -49,14 +48,26 @@
 #define CTL_SLEW_MASK		(0x7 << 4)
 #define CTL_SLEW_SHIFT		4
 #define CTL_RESET			(1 << 2)
+#define CTL_MODE_VSEL0_MODE	BIT(0)
+#define CTL_MODE_VSEL1_MODE	BIT(1)
 
 #define FAN53555_NVOLTAGES	64	/* Numbers of voltages */
+#define FAN53526_NVOLTAGES	128
 
 enum fan53555_vendor {
-	FAN53555_VENDOR_FAIRCHILD = 0,
+	FAN53526_VENDOR_FAIRCHILD = 0,
+	FAN53555_VENDOR_FAIRCHILD,
 	FAN53555_VENDOR_SILERGY,
 };
 
+enum {
+	FAN53526_CHIP_ID_01 = 1,
+};
+
+enum {
+	FAN53526_CHIP_REV_08 = 8,
+};
+
 /* IC Type */
 enum {
 	FAN53555_CHIP_ID_00 = 0,
@@ -94,8 +105,12 @@ struct fan53555_device_info {
 	/* Voltage range and step(linear) */
 	unsigned int vsel_min;
 	unsigned int vsel_step;
+	unsigned int vsel_count;
 	/* Voltage slew rate limiting */
 	unsigned int slew_rate;
+	/* Mode */
+	unsigned int mode_reg;
+	unsigned int mode_mask;
 	/* Sleep voltage cache */
 	unsigned int sleep_vol_cache;
 };
@@ -111,7 +126,7 @@ static int fan53555_set_suspend_voltage(struct regulator_dev *rdev, int uV)
 	if (ret < 0)
 		return ret;
 	ret = regmap_update_bits(di->regmap, di->sleep_reg,
-					VSEL_NSEL_MASK, ret);
+				 di->desc.vsel_mask, ret);
 	if (ret < 0)
 		return ret;
 	/* Cache the sleep voltage setting.
@@ -143,11 +158,11 @@ static int fan53555_set_mode(struct regulator_dev *rdev, unsigned int mode)
 
 	switch (mode) {
 	case REGULATOR_MODE_FAST:
-		regmap_update_bits(di->regmap, di->vol_reg,
-				VSEL_MODE, VSEL_MODE);
+		regmap_update_bits(di->regmap, di->mode_reg,
+				   di->mode_mask, di->mode_mask);
 		break;
 	case REGULATOR_MODE_NORMAL:
-		regmap_update_bits(di->regmap, di->vol_reg, VSEL_MODE, 0);
+		regmap_update_bits(di->regmap, di->vol_reg, di->mode_mask, 0);
 		break;
 	default:
 		return -EINVAL;
@@ -161,10 +176,10 @@ static unsigned int fan53555_get_mode(struct regulator_dev *rdev)
 	unsigned int val;
 	int ret = 0;
 
-	ret = regmap_read(di->regmap, di->vol_reg, &val);
+	ret = regmap_read(di->regmap, di->mode_reg, &val);
 	if (ret < 0)
 		return ret;
-	if (val & VSEL_MODE)
+	if (val & di->mode_mask)
 		return REGULATOR_MODE_FAST;
 	else
 		return REGULATOR_MODE_NORMAL;
@@ -219,6 +234,34 @@ static const struct regulator_ops fan53555_regulator_ops = {
 	.set_suspend_disable = fan53555_set_suspend_disable,
 };
 
+static int fan53526_voltages_setup_fairchild(struct fan53555_device_info *di)
+{
+	/* Init voltage range and step */
+	switch (di->chip_id) {
+	case FAN53526_CHIP_ID_01:
+		switch (di->chip_rev) {
+		case FAN53526_CHIP_REV_08:
+			di->vsel_min = 600000;
+			di->vsel_step = 6250;
+			break;
+		default:
+			dev_err(di->dev,
+				"Chip ID %d with rev %d not supported!\n",
+				di->chip_id, di->chip_rev);
+			return -EINVAL;
+		}
+		break;
+	default:
+		dev_err(di->dev,
+			"Chip ID %d not supported!\n", di->chip_id);
+		return -EINVAL;
+	}
+
+	di->vsel_count = FAN53526_NVOLTAGES;
+
+	return 0;
+}
+
 static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di)
 {
 	/* Init voltage range and step */
@@ -257,6 +300,8 @@ static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di)
 		return -EINVAL;
 	}
 
+	di->vsel_count = FAN53555_NVOLTAGES;
+
 	return 0;
 }
 
@@ -274,6 +319,8 @@ static int fan53555_voltages_setup_silergy(struct fan53555_device_info *di)
 		return -EINVAL;
 	}
 
+	di->vsel_count = FAN53555_NVOLTAGES;
+
 	return 0;
 }
 
@@ -302,7 +349,35 @@ static int fan53555_device_setup(struct fan53555_device_info *di,
 		return -EINVAL;
 	}
 
+	/* Setup mode control register */
+	switch (di->vendor) {
+	case FAN53526_VENDOR_FAIRCHILD:
+		di->mode_reg = FAN53555_CONTROL;
+
+		switch (pdata->sleep_vsel_id) {
+		case FAN53555_VSEL_ID_0:
+			di->mode_mask = CTL_MODE_VSEL1_MODE;
+			break;
+		case FAN53555_VSEL_ID_1:
+			di->mode_mask = CTL_MODE_VSEL0_MODE;
+			break;
+		}
+		break;
+	case FAN53555_VENDOR_FAIRCHILD:
+	case FAN53555_VENDOR_SILERGY:
+		di->mode_reg = di->vol_reg;
+		di->mode_mask = VSEL_MODE;
+		break;
+	default:
+		dev_err(di->dev, "vendor %d not supported!\n", di->vendor);
+		return -EINVAL;
+	}
+
+	/* Setup voltage range */
 	switch (di->vendor) {
+	case FAN53526_VENDOR_FAIRCHILD:
+		ret = fan53526_voltages_setup_fairchild(di);
+		break;
 	case FAN53555_VENDOR_FAIRCHILD:
 		ret = fan53555_voltages_setup_fairchild(di);
 		break;
@@ -326,13 +401,13 @@ static int fan53555_regulator_register(struct fan53555_device_info *di,
 	rdesc->supply_name = "vin";
 	rdesc->ops = &fan53555_regulator_ops;
 	rdesc->type = REGULATOR_VOLTAGE;
-	rdesc->n_voltages = FAN53555_NVOLTAGES;
+	rdesc->n_voltages = di->vsel_count;
 	rdesc->enable_reg = di->vol_reg;
 	rdesc->enable_mask = VSEL_BUCK_EN;
 	rdesc->min_uV = di->vsel_min;
 	rdesc->uV_step = di->vsel_step;
 	rdesc->vsel_reg = di->vol_reg;
-	rdesc->vsel_mask = VSEL_NSEL_MASK;
+	rdesc->vsel_mask = di->vsel_count - 1;
 	rdesc->owner = THIS_MODULE;
 
 	di->rdev = devm_regulator_register(di->dev, &di->desc, config);
@@ -368,6 +443,9 @@ static struct fan53555_platform_data *fan53555_parse_dt(struct device *dev,
 
 static const struct of_device_id fan53555_dt_ids[] = {
 	{
+		.compatible = "fcs,fan53526",
+		.data = (void *)FAN53526_VENDOR_FAIRCHILD,
+	}, {
 		.compatible = "fcs,fan53555",
 		.data = (void *)FAN53555_VENDOR_FAIRCHILD
 	}, {
@@ -412,11 +490,13 @@ static int fan53555_regulator_probe(struct i2c_client *client,
 	} else {
 		/* if no ramp constraint set, get the pdata ramp_delay */
 		if (!di->regulator->constraints.ramp_delay) {
-			int slew_idx = (pdata->slew_rate & 0x7)
-						? pdata->slew_rate : 0;
+			if (pdata->slew_rate >= ARRAY_SIZE(slew_rates)) {
+				dev_err(&client->dev, "Invalid slew_rate\n");
+				return -EINVAL;
+			}
 
 			di->regulator->constraints.ramp_delay
-						= slew_rates[slew_idx];
+					= slew_rates[pdata->slew_rate];
 		}
 
 		di->vendor = id->driver_data;
@@ -467,6 +547,9 @@ static int fan53555_regulator_probe(struct i2c_client *client,
 
 static const struct i2c_device_id fan53555_id[] = {
 	{
+		.name = "fan53526",
+		.driver_data = FAN53526_VENDOR_FAIRCHILD
+	}, {
 		.name = "fan53555",
 		.driver_data = FAN53555_VENDOR_FAIRCHILD
 	}, {
diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c
index 9abdb9130766..b5afc9db2c61 100644
--- a/drivers/regulator/fixed.c
+++ b/drivers/regulator/fixed.c
@@ -79,15 +79,6 @@ of_get_fixed_voltage_config(struct device *dev,
 
 	of_property_read_u32(np, "startup-delay-us", &config->startup_delay);
 
-	/*
-	 * FIXME: we pulled active low/high and open drain handling into
-	 * gpiolib so it will be handled there. Delete this in the second
-	 * step when we also remove the custom inversion handling for all
-	 * legacy boardfiles.
-	 */
-	config->enable_high = 1;
-	config->gpio_is_open_drain = 0;
-
 	if (of_find_property(np, "vin-supply", NULL))
 		config->input_supply = "vin";
 
@@ -151,24 +142,14 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 
 	drvdata->desc.fixed_uV = config->microvolts;
 
-	cfg.ena_gpio_invert = !config->enable_high;
-	if (config->enabled_at_boot) {
-		if (config->enable_high)
-			gflags = GPIOD_OUT_HIGH;
-		else
-			gflags = GPIOD_OUT_LOW;
-	} else {
-		if (config->enable_high)
-			gflags = GPIOD_OUT_LOW;
-		else
-			gflags = GPIOD_OUT_HIGH;
-	}
-	if (config->gpio_is_open_drain) {
-		if (gflags == GPIOD_OUT_HIGH)
-			gflags = GPIOD_OUT_HIGH_OPEN_DRAIN;
-		else
-			gflags = GPIOD_OUT_LOW_OPEN_DRAIN;
-	}
+	/*
+	 * The signal will be inverted by the GPIO core if flagged so in the
+	 * decriptor.
+	 */
+	if (config->enabled_at_boot)
+		gflags = GPIOD_OUT_HIGH;
+	else
+		gflags = GPIOD_OUT_LOW;
 
 	/*
 	 * Some fixed regulators share the enable line between two
diff --git a/drivers/regulator/gpio-regulator.c b/drivers/regulator/gpio-regulator.c
index b2f5ec4f658a..6157001df0a4 100644
--- a/drivers/regulator/gpio-regulator.c
+++ b/drivers/regulator/gpio-regulator.c
@@ -30,16 +30,15 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 #include <linux/regulator/gpio-regulator.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/of.h>
-#include <linux/of_gpio.h>
 
 struct gpio_regulator_data {
 	struct regulator_desc desc;
 	struct regulator_dev *dev;
 
-	struct gpio *gpios;
+	struct gpio_desc **gpiods;
 	int nr_gpios;
 
 	struct gpio_regulator_state *states;
@@ -82,7 +81,7 @@ static int gpio_regulator_set_voltage(struct regulator_dev *dev,
 
 	for (ptr = 0; ptr < data->nr_gpios; ptr++) {
 		state = (target & (1 << ptr)) >> ptr;
-		gpio_set_value_cansleep(data->gpios[ptr].gpio, state);
+		gpiod_set_value_cansleep(data->gpiods[ptr], state);
 	}
 	data->state = target;
 
@@ -119,7 +118,7 @@ static int gpio_regulator_set_current_limit(struct regulator_dev *dev,
 
 	for (ptr = 0; ptr < data->nr_gpios; ptr++) {
 		state = (target & (1 << ptr)) >> ptr;
-		gpio_set_value_cansleep(data->gpios[ptr].gpio, state);
+		gpiod_set_value_cansleep(data->gpiods[ptr], state);
 	}
 	data->state = target;
 
@@ -138,7 +137,8 @@ of_get_gpio_regulator_config(struct device *dev, struct device_node *np,
 {
 	struct gpio_regulator_config *config;
 	const char *regtype;
-	int proplen, gpio, i;
+	int proplen, i;
+	int ngpios;
 	int ret;
 
 	config = devm_kzalloc(dev,
@@ -153,59 +153,36 @@ of_get_gpio_regulator_config(struct device *dev, struct device_node *np,
 
 	config->supply_name = config->init_data->constraints.name;
 
-	if (of_property_read_bool(np, "enable-active-high"))
-		config->enable_high = true;
-
 	if (of_property_read_bool(np, "enable-at-boot"))
 		config->enabled_at_boot = true;
 
 	of_property_read_u32(np, "startup-delay-us", &config->startup_delay);
 
-	config->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0);
-	if (config->enable_gpio < 0 && config->enable_gpio != -ENOENT)
-		return ERR_PTR(config->enable_gpio);
-
-	/* Fetch GPIOs. - optional property*/
-	ret = of_gpio_count(np);
-	if ((ret < 0) && (ret != -ENOENT))
-		return ERR_PTR(ret);
-
-	if (ret > 0) {
-		config->nr_gpios = ret;
-		config->gpios = devm_kcalloc(dev,
-					config->nr_gpios, sizeof(struct gpio),
-					GFP_KERNEL);
-		if (!config->gpios)
+	/* Fetch GPIO init levels */
+	ngpios = gpiod_count(dev, NULL);
+	if (ngpios > 0) {
+		config->gflags = devm_kzalloc(dev,
+					      sizeof(enum gpiod_flags)
+					      * ngpios,
+					      GFP_KERNEL);
+		if (!config->gflags)
 			return ERR_PTR(-ENOMEM);
 
-		proplen = of_property_count_u32_elems(np, "gpios-states");
-		/* optional property */
-		if (proplen < 0)
-			proplen = 0;
+		for (i = 0; i < ngpios; i++) {
+			u32 val;
 
-		if (proplen > 0 && proplen != config->nr_gpios) {
-			dev_warn(dev, "gpios <-> gpios-states mismatch\n");
-			proplen = 0;
-		}
+			ret = of_property_read_u32_index(np, "gpios-states", i,
+							 &val);
 
-		for (i = 0; i < config->nr_gpios; i++) {
-			gpio = of_get_named_gpio(np, "gpios", i);
-			if (gpio < 0) {
-				if (gpio != -ENOENT)
-					return ERR_PTR(gpio);
-				break;
-			}
-			config->gpios[i].gpio = gpio;
-			config->gpios[i].label = config->supply_name;
-			if (proplen > 0) {
-				of_property_read_u32_index(np, "gpios-states",
-							   i, &ret);
-				if (ret)
-					config->gpios[i].flags =
-							   GPIOF_OUT_INIT_HIGH;
-			}
+			/* Default to high per specification */
+			if (ret)
+				config->gflags[i] = GPIOD_OUT_HIGH;
+			else
+				config->gflags[i] =
+					val ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW;
 		}
 	}
+	config->ngpios = ngpios;
 
 	/* Fetch states. */
 	proplen = of_property_count_u32_elems(np, "states");
@@ -251,59 +228,56 @@ static struct regulator_ops gpio_regulator_current_ops = {
 
 static int gpio_regulator_probe(struct platform_device *pdev)
 {
-	struct gpio_regulator_config *config = dev_get_platdata(&pdev->dev);
-	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct gpio_regulator_config *config = dev_get_platdata(dev);
+	struct device_node *np = dev->of_node;
 	struct gpio_regulator_data *drvdata;
 	struct regulator_config cfg = { };
-	int ptr, ret, state;
+	enum gpiod_flags gflags;
+	int ptr, ret, state, i;
 
-	drvdata = devm_kzalloc(&pdev->dev, sizeof(struct gpio_regulator_data),
+	drvdata = devm_kzalloc(dev, sizeof(struct gpio_regulator_data),
 			       GFP_KERNEL);
 	if (drvdata == NULL)
 		return -ENOMEM;
 
 	if (np) {
-		config = of_get_gpio_regulator_config(&pdev->dev, np,
+		config = of_get_gpio_regulator_config(dev, np,
 						      &drvdata->desc);
 		if (IS_ERR(config))
 			return PTR_ERR(config);
 	}
 
-	drvdata->desc.name = kstrdup(config->supply_name, GFP_KERNEL);
+	drvdata->desc.name = devm_kstrdup(dev, config->supply_name, GFP_KERNEL);
 	if (drvdata->desc.name == NULL) {
-		dev_err(&pdev->dev, "Failed to allocate supply name\n");
+		dev_err(dev, "Failed to allocate supply name\n");
 		return -ENOMEM;
 	}
 
-	if (config->nr_gpios != 0) {
-		drvdata->gpios = kmemdup(config->gpios,
-					 config->nr_gpios * sizeof(struct gpio),
-					 GFP_KERNEL);
-		if (drvdata->gpios == NULL) {
-			dev_err(&pdev->dev, "Failed to allocate gpio data\n");
-			ret = -ENOMEM;
-			goto err_name;
-		}
-
-		drvdata->nr_gpios = config->nr_gpios;
-		ret = gpio_request_array(drvdata->gpios, drvdata->nr_gpios);
-		if (ret) {
-			if (ret != -EPROBE_DEFER)
-				dev_err(&pdev->dev,
-					"Could not obtain regulator setting GPIOs: %d\n",
-					ret);
-			goto err_memgpio;
-		}
+	drvdata->gpiods = devm_kzalloc(dev, sizeof(struct gpio_desc *),
+				       GFP_KERNEL);
+	if (!drvdata->gpiods)
+		return -ENOMEM;
+	for (i = 0; i < config->ngpios; i++) {
+		drvdata->gpiods[i] = devm_gpiod_get_index(dev,
+							  NULL,
+							  i,
+							  config->gflags[i]);
+		if (IS_ERR(drvdata->gpiods[i]))
+			return PTR_ERR(drvdata->gpiods[i]);
+		/* This is good to know */
+		gpiod_set_consumer_name(drvdata->gpiods[i], drvdata->desc.name);
 	}
+	drvdata->nr_gpios = config->ngpios;
 
-	drvdata->states = kmemdup(config->states,
-				  config->nr_states *
-					 sizeof(struct gpio_regulator_state),
-				  GFP_KERNEL);
+	drvdata->states = devm_kmemdup(dev,
+				       config->states,
+				       config->nr_states *
+				       sizeof(struct gpio_regulator_state),
+				       GFP_KERNEL);
 	if (drvdata->states == NULL) {
-		dev_err(&pdev->dev, "Failed to allocate state data\n");
-		ret = -ENOMEM;
-		goto err_stategpio;
+		dev_err(dev, "Failed to allocate state data\n");
+		return -ENOMEM;
 	}
 	drvdata->nr_states = config->nr_states;
 
@@ -322,61 +296,46 @@ static int gpio_regulator_probe(struct platform_device *pdev)
 		drvdata->desc.ops = &gpio_regulator_current_ops;
 		break;
 	default:
-		dev_err(&pdev->dev, "No regulator type set\n");
-		ret = -EINVAL;
-		goto err_memstate;
+		dev_err(dev, "No regulator type set\n");
+		return -EINVAL;
 	}
 
 	/* build initial state from gpio init data. */
 	state = 0;
 	for (ptr = 0; ptr < drvdata->nr_gpios; ptr++) {
-		if (config->gpios[ptr].flags & GPIOF_OUT_INIT_HIGH)
+		if (config->gflags[ptr] == GPIOD_OUT_HIGH)
 			state |= (1 << ptr);
 	}
 	drvdata->state = state;
 
-	cfg.dev = &pdev->dev;
+	cfg.dev = dev;
 	cfg.init_data = config->init_data;
 	cfg.driver_data = drvdata;
 	cfg.of_node = np;
 
-	if (gpio_is_valid(config->enable_gpio)) {
-		cfg.ena_gpio = config->enable_gpio;
-		cfg.ena_gpio_initialized = true;
-	}
-	cfg.ena_gpio_invert = !config->enable_high;
-	if (config->enabled_at_boot) {
-		if (config->enable_high)
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
-		else
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
-	} else {
-		if (config->enable_high)
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
-		else
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
-	}
+	/*
+	 * The signal will be inverted by the GPIO core if flagged so in the
+	 * decriptor.
+	 */
+	if (config->enabled_at_boot)
+		gflags = GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE;
+	else
+		gflags = GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE;
+
+	cfg.ena_gpiod = gpiod_get_optional(dev, "enable", gflags);
+	if (IS_ERR(cfg.ena_gpiod))
+		return PTR_ERR(cfg.ena_gpiod);
 
 	drvdata->dev = regulator_register(&drvdata->desc, &cfg);
 	if (IS_ERR(drvdata->dev)) {
 		ret = PTR_ERR(drvdata->dev);
-		dev_err(&pdev->dev, "Failed to register regulator: %d\n", ret);
-		goto err_memstate;
+		dev_err(dev, "Failed to register regulator: %d\n", ret);
+		return ret;
 	}
 
 	platform_set_drvdata(pdev, drvdata);
 
 	return 0;
-
-err_memstate:
-	kfree(drvdata->states);
-err_stategpio:
-	gpio_free_array(drvdata->gpios, drvdata->nr_gpios);
-err_memgpio:
-	kfree(drvdata->gpios);
-err_name:
-	kfree(drvdata->desc.name);
-	return ret;
 }
 
 static int gpio_regulator_remove(struct platform_device *pdev)
@@ -385,13 +344,6 @@ static int gpio_regulator_remove(struct platform_device *pdev)
 
 	regulator_unregister(drvdata->dev);
 
-	gpio_free_array(drvdata->gpios, drvdata->nr_gpios);
-
-	kfree(drvdata->states);
-	kfree(drvdata->gpios);
-
-	kfree(drvdata->desc.name);
-
 	return 0;
 }
 
diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index 5686a1335bd3..32d3f0499e2d 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -594,28 +594,30 @@ int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev,
 EXPORT_SYMBOL_GPL(regulator_list_voltage_pickable_linear_range);
 
 /**
- * regulator_list_voltage_linear_range - List voltages for linear ranges
+ * regulator_desc_list_voltage_linear_range - List voltages for linear ranges
  *
- * @rdev: Regulator device
+ * @desc: Regulator desc for regulator which volatges are to be listed
  * @selector: Selector to convert into a voltage
  *
  * Regulators with a series of simple linear mappings between voltages
- * and selectors can set linear_ranges in the regulator descriptor and
- * then use this function as their list_voltage() operation,
+ * and selectors who have set linear_ranges in the regulator descriptor
+ * can use this function prior regulator registration to list voltages.
+ * This is useful when voltages need to be listed during device-tree
+ * parsing.
  */
-int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
-					unsigned int selector)
+int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc,
+					     unsigned int selector)
 {
 	const struct regulator_linear_range *range;
 	int i;
 
-	if (!rdev->desc->n_linear_ranges) {
-		BUG_ON(!rdev->desc->n_linear_ranges);
+	if (!desc->n_linear_ranges) {
+		BUG_ON(!desc->n_linear_ranges);
 		return -EINVAL;
 	}
 
-	for (i = 0; i < rdev->desc->n_linear_ranges; i++) {
-		range = &rdev->desc->linear_ranges[i];
+	for (i = 0; i < desc->n_linear_ranges; i++) {
+		range = &desc->linear_ranges[i];
 
 		if (!(selector >= range->min_sel &&
 		      selector <= range->max_sel))
@@ -628,6 +630,23 @@ int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
 
 	return -EINVAL;
 }
+EXPORT_SYMBOL_GPL(regulator_desc_list_voltage_linear_range);
+
+/**
+ * regulator_list_voltage_linear_range - List voltages for linear ranges
+ *
+ * @rdev: Regulator device
+ * @selector: Selector to convert into a voltage
+ *
+ * Regulators with a series of simple linear mappings between voltages
+ * and selectors can set linear_ranges in the regulator descriptor and
+ * then use this function as their list_voltage() operation,
+ */
+int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
+					unsigned int selector)
+{
+	return regulator_desc_list_voltage_linear_range(rdev->desc, selector);
+}
 EXPORT_SYMBOL_GPL(regulator_list_voltage_linear_range);
 
 /**
@@ -761,3 +780,89 @@ int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
 				  rdev->desc->active_discharge_mask, val);
 }
 EXPORT_SYMBOL_GPL(regulator_set_active_discharge_regmap);
+
+/**
+ * regulator_set_current_limit_regmap - set_current_limit for regmap users
+ *
+ * @rdev: regulator to operate on
+ * @min_uA: Lower bound for current limit
+ * @max_uA: Upper bound for current limit
+ *
+ * Regulators that use regmap for their register I/O can set curr_table,
+ * csel_reg and csel_mask fields in their descriptor and then use this
+ * as their set_current_limit operation, saving some code.
+ */
+int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
+				       int min_uA, int max_uA)
+{
+	unsigned int n_currents = rdev->desc->n_current_limits;
+	int i, sel = -1;
+
+	if (n_currents == 0)
+		return -EINVAL;
+
+	if (rdev->desc->curr_table) {
+		const unsigned int *curr_table = rdev->desc->curr_table;
+		bool ascend = curr_table[n_currents - 1] > curr_table[0];
+
+		/* search for closest to maximum */
+		if (ascend) {
+			for (i = n_currents - 1; i >= 0; i--) {
+				if (min_uA <= curr_table[i] &&
+				    curr_table[i] <= max_uA) {
+					sel = i;
+					break;
+				}
+			}
+		} else {
+			for (i = 0; i < n_currents; i++) {
+				if (min_uA <= curr_table[i] &&
+				    curr_table[i] <= max_uA) {
+					sel = i;
+					break;
+				}
+			}
+		}
+	}
+
+	if (sel < 0)
+		return -EINVAL;
+
+	sel <<= ffs(rdev->desc->csel_mask) - 1;
+
+	return regmap_update_bits(rdev->regmap, rdev->desc->csel_reg,
+				  rdev->desc->csel_mask, sel);
+}
+EXPORT_SYMBOL_GPL(regulator_set_current_limit_regmap);
+
+/**
+ * regulator_get_current_limit_regmap - get_current_limit for regmap users
+ *
+ * @rdev: regulator to operate on
+ *
+ * Regulators that use regmap for their register I/O can set the
+ * csel_reg and csel_mask fields in their descriptor and then use this
+ * as their get_current_limit operation, saving some code.
+ */
+int regulator_get_current_limit_regmap(struct regulator_dev *rdev)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->csel_reg, &val);
+	if (ret != 0)
+		return ret;
+
+	val &= rdev->desc->csel_mask;
+	val >>= ffs(rdev->desc->csel_mask) - 1;
+
+	if (rdev->desc->curr_table) {
+		if (val >= rdev->desc->n_current_limits)
+			return -EINVAL;
+
+		return rdev->desc->curr_table[val];
+	}
+
+	return -EINVAL;
+}
+EXPORT_SYMBOL_GPL(regulator_get_current_limit_regmap);
diff --git a/drivers/regulator/hi655x-regulator.c b/drivers/regulator/hi655x-regulator.c
index 36ae54b53814..bba24a6fdb1e 100644
--- a/drivers/regulator/hi655x-regulator.c
+++ b/drivers/regulator/hi655x-regulator.c
@@ -28,7 +28,6 @@
 struct hi655x_regulator {
 	unsigned int disable_reg;
 	unsigned int status_reg;
-	unsigned int ctrl_regs;
 	unsigned int ctrl_mask;
 	struct regulator_desc rdesc;
 };
diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c
index 4abd8e9c81e5..6f28bba81d13 100644
--- a/drivers/regulator/isl6271a-regulator.c
+++ b/drivers/regulator/isl6271a-regulator.c
@@ -31,7 +31,6 @@
 /* PMIC details */
 struct isl_pmic {
 	struct i2c_client	*client;
-	struct regulator_dev	*rdev[3];
 	struct mutex		mtx;
 };
 
@@ -66,14 +65,14 @@ static int isl6271a_set_voltage_sel(struct regulator_dev *dev,
 	return err;
 }
 
-static struct regulator_ops isl_core_ops = {
+static const struct regulator_ops isl_core_ops = {
 	.get_voltage_sel = isl6271a_get_voltage_sel,
 	.set_voltage_sel = isl6271a_set_voltage_sel,
 	.list_voltage	= regulator_list_voltage_linear,
 	.map_voltage	= regulator_map_voltage_linear,
 };
 
-static struct regulator_ops isl_fixed_ops = {
+static const struct regulator_ops isl_fixed_ops = {
 	.list_voltage	= regulator_list_voltage_linear,
 };
 
@@ -109,6 +108,7 @@ static const struct regulator_desc isl_rd[] = {
 static int isl6271a_probe(struct i2c_client *i2c,
 				     const struct i2c_device_id *id)
 {
+	struct regulator_dev *rdev;
 	struct regulator_config config = { };
 	struct regulator_init_data *init_data	= dev_get_platdata(&i2c->dev);
 	struct isl_pmic *pmic;
@@ -133,11 +133,10 @@ static int isl6271a_probe(struct i2c_client *i2c,
 			config.init_data = NULL;
 		config.driver_data = pmic;
 
-		pmic->rdev[i] = devm_regulator_register(&i2c->dev, &isl_rd[i],
-							&config);
-		if (IS_ERR(pmic->rdev[i])) {
+		rdev = devm_regulator_register(&i2c->dev, &isl_rd[i], &config);
+		if (IS_ERR(rdev)) {
 			dev_err(&i2c->dev, "failed to register %s\n", id->name);
-			return PTR_ERR(pmic->rdev[i]);
+			return PTR_ERR(rdev);
 		}
 	}
 
diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
index 8c0e8419c43f..c876e161052a 100644
--- a/drivers/regulator/lm363x-regulator.c
+++ b/drivers/regulator/lm363x-regulator.c
@@ -258,6 +258,9 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
 	 * Register update is required if the pin is used.
 	 */
 	gpiod = lm363x_regulator_of_get_enable_gpio(dev, id);
+	if (IS_ERR(gpiod))
+		return PTR_ERR(gpiod);
+
 	if (gpiod) {
 		cfg.ena_gpiod = gpiod;
 
@@ -265,8 +268,7 @@ static int lm363x_regulator_probe(struct platform_device *pdev)
 					 LM3632_EXT_EN_MASK,
 					 LM3632_EXT_EN_MASK);
 		if (ret) {
-			if (gpiod)
-				gpiod_put(gpiod);
+			gpiod_put(gpiod);
 			dev_err(dev, "External pin err: %d\n", ret);
 			return ret;
 		}
diff --git a/drivers/regulator/lochnagar-regulator.c b/drivers/regulator/lochnagar-regulator.c
index 47f5663e99c8..ff97cc50f2eb 100644
--- a/drivers/regulator/lochnagar-regulator.c
+++ b/drivers/regulator/lochnagar-regulator.c
@@ -232,8 +232,9 @@ static const struct of_device_id lochnagar_of_match[] = {
 		.compatible = "cirrus,lochnagar2-vddcore",
 		.data = &lochnagar_regulators[LOCHNAGAR_VDDCORE],
 	},
-	{},
+	{}
 };
+MODULE_DEVICE_TABLE(of, lochnagar_of_match);
 
 static int lochnagar_regulator_probe(struct platform_device *pdev)
 {
diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c
index 204b5c5270e0..9e45112658ba 100644
--- a/drivers/regulator/lp3971.c
+++ b/drivers/regulator/lp3971.c
@@ -159,7 +159,7 @@ static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev,
 			selector << LDO_VOL_CONTR_SHIFT(ldo));
 }
 
-static struct regulator_ops lp3971_ldo_ops = {
+static const struct regulator_ops lp3971_ldo_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.is_enabled = lp3971_ldo_is_enabled,
@@ -233,7 +233,7 @@ static int lp3971_dcdc_set_voltage_sel(struct regulator_dev *dev,
 	       0 << BUCK_VOL_CHANGE_SHIFT(buck));
 }
 
-static struct regulator_ops lp3971_dcdc_ops = {
+static const struct regulator_ops lp3971_dcdc_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.is_enabled = lp3971_dcdc_is_enabled,
diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c
index ff0c275f902e..fb098198b688 100644
--- a/drivers/regulator/lp3972.c
+++ b/drivers/regulator/lp3972.c
@@ -305,7 +305,7 @@ static int lp3972_ldo_set_voltage_sel(struct regulator_dev *dev,
 	return ret;
 }
 
-static struct regulator_ops lp3972_ldo_ops = {
+static const struct regulator_ops lp3972_ldo_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.is_enabled = lp3972_ldo_is_enabled,
@@ -386,7 +386,7 @@ static int lp3972_dcdc_set_voltage_sel(struct regulator_dev *dev,
 				LP3972_VOL_CHANGE_FLAG_MASK, 0);
 }
 
-static struct regulator_ops lp3972_dcdc_ops = {
+static const struct regulator_ops lp3972_dcdc_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.is_enabled = lp3972_dcdc_is_enabled,
diff --git a/drivers/regulator/lp872x.c b/drivers/regulator/lp872x.c
index 38992112fd6e..ca95257ce252 100644
--- a/drivers/regulator/lp872x.c
+++ b/drivers/regulator/lp872x.c
@@ -353,64 +353,6 @@ static int lp872x_buck_get_voltage_sel(struct regulator_dev *rdev)
 	return val & LP872X_VOUT_M;
 }
 
-static int lp8725_buck_set_current_limit(struct regulator_dev *rdev,
-					int min_uA, int max_uA)
-{
-	struct lp872x *lp = rdev_get_drvdata(rdev);
-	enum lp872x_regulator_id buck = rdev_get_id(rdev);
-	int i;
-	u8 addr;
-
-	switch (buck) {
-	case LP8725_ID_BUCK1:
-		addr = LP8725_BUCK1_VOUT2;
-		break;
-	case LP8725_ID_BUCK2:
-		addr = LP8725_BUCK2_VOUT2;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	for (i = ARRAY_SIZE(lp8725_buck_uA) - 1; i >= 0; i--) {
-		if (lp8725_buck_uA[i] >= min_uA &&
-			lp8725_buck_uA[i] <= max_uA)
-			return lp872x_update_bits(lp, addr,
-						  LP8725_BUCK_CL_M,
-						  i << LP8725_BUCK_CL_S);
-	}
-
-	return -EINVAL;
-}
-
-static int lp8725_buck_get_current_limit(struct regulator_dev *rdev)
-{
-	struct lp872x *lp = rdev_get_drvdata(rdev);
-	enum lp872x_regulator_id buck = rdev_get_id(rdev);
-	u8 addr, val;
-	int ret;
-
-	switch (buck) {
-	case LP8725_ID_BUCK1:
-		addr = LP8725_BUCK1_VOUT2;
-		break;
-	case LP8725_ID_BUCK2:
-		addr = LP8725_BUCK2_VOUT2;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	ret = lp872x_read_byte(lp, addr, &val);
-	if (ret)
-		return ret;
-
-	val = (val & LP8725_BUCK_CL_M) >> LP8725_BUCK_CL_S;
-
-	return (val < ARRAY_SIZE(lp8725_buck_uA)) ?
-			lp8725_buck_uA[val] : -EINVAL;
-}
-
 static int lp872x_buck_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
 	struct lp872x *lp = rdev_get_drvdata(rdev);
@@ -478,7 +420,7 @@ static unsigned int lp872x_buck_get_mode(struct regulator_dev *rdev)
 	return val & mask ? REGULATOR_MODE_FAST : REGULATOR_MODE_NORMAL;
 }
 
-static struct regulator_ops lp872x_ldo_ops = {
+static const struct regulator_ops lp872x_ldo_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
@@ -489,7 +431,7 @@ static struct regulator_ops lp872x_ldo_ops = {
 	.enable_time = lp872x_regulator_enable_time,
 };
 
-static struct regulator_ops lp8720_buck_ops = {
+static const struct regulator_ops lp8720_buck_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = lp872x_buck_set_voltage_sel,
@@ -502,7 +444,7 @@ static struct regulator_ops lp8720_buck_ops = {
 	.get_mode = lp872x_buck_get_mode,
 };
 
-static struct regulator_ops lp8725_buck_ops = {
+static const struct regulator_ops lp8725_buck_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = lp872x_buck_set_voltage_sel,
@@ -513,11 +455,11 @@ static struct regulator_ops lp8725_buck_ops = {
 	.enable_time = lp872x_regulator_enable_time,
 	.set_mode = lp872x_buck_set_mode,
 	.get_mode = lp872x_buck_get_mode,
-	.set_current_limit = lp8725_buck_set_current_limit,
-	.get_current_limit = lp8725_buck_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 };
 
-static struct regulator_desc lp8720_regulator_desc[] = {
+static const struct regulator_desc lp8720_regulator_desc[] = {
 	{
 		.name = "ldo1",
 		.of_match = of_match_ptr("ldo1"),
@@ -602,7 +544,7 @@ static struct regulator_desc lp8720_regulator_desc[] = {
 	},
 };
 
-static struct regulator_desc lp8725_regulator_desc[] = {
+static const struct regulator_desc lp8725_regulator_desc[] = {
 	{
 		.name = "ldo1",
 		.of_match = of_match_ptr("ldo1"),
@@ -712,6 +654,10 @@ static struct regulator_desc lp8725_regulator_desc[] = {
 		.owner = THIS_MODULE,
 		.enable_reg = LP872X_GENERAL_CFG,
 		.enable_mask = LP8725_BUCK1_EN_M,
+		.curr_table = lp8725_buck_uA,
+		.n_current_limits = ARRAY_SIZE(lp8725_buck_uA),
+		.csel_reg = LP8725_BUCK1_VOUT2,
+		.csel_mask = LP8725_BUCK_CL_M,
 	},
 	{
 		.name = "buck2",
@@ -724,6 +670,10 @@ static struct regulator_desc lp8725_regulator_desc[] = {
 		.owner = THIS_MODULE,
 		.enable_reg = LP872X_GENERAL_CFG,
 		.enable_mask = LP8725_BUCK2_EN_M,
+		.curr_table = lp8725_buck_uA,
+		.n_current_limits = ARRAY_SIZE(lp8725_buck_uA),
+		.csel_reg = LP8725_BUCK2_VOUT2,
+		.csel_mask = LP8725_BUCK_CL_M,
 	},
 };
 
@@ -820,7 +770,7 @@ static struct regulator_init_data
 
 static int lp872x_regulator_register(struct lp872x *lp)
 {
-	struct regulator_desc *desc;
+	const struct regulator_desc *desc;
 	struct regulator_config cfg = { };
 	struct regulator_dev *rdev;
 	int i;
diff --git a/drivers/regulator/lp873x-regulator.c b/drivers/regulator/lp873x-regulator.c
index 70e3df653381..b55de293ca7a 100644
--- a/drivers/regulator/lp873x-regulator.c
+++ b/drivers/regulator/lp873x-regulator.c
@@ -39,6 +39,10 @@
 			.ramp_delay		= _delay,		\
 			.linear_ranges		= _lr,			\
 			.n_linear_ranges	= ARRAY_SIZE(_lr),	\
+			.curr_table	= lp873x_buck_uA,		\
+			.n_current_limits = ARRAY_SIZE(lp873x_buck_uA),	\
+			.csel_reg	= (_cr),			\
+			.csel_mask	= LP873X_BUCK0_CTRL_2_BUCK0_ILIM,\
 		},							\
 		.ctrl2_reg = _cr,					\
 	}
@@ -61,7 +65,7 @@ static const struct regulator_linear_range ldo0_ldo1_ranges[] = {
 	REGULATOR_LINEAR_RANGE(800000, 0x0, 0x19, 100000),
 };
 
-static unsigned int lp873x_buck_ramp_delay[] = {
+static const unsigned int lp873x_buck_ramp_delay[] = {
 	30000, 15000, 10000, 7500, 3800, 1900, 940, 470
 };
 
@@ -108,45 +112,8 @@ static int lp873x_buck_set_ramp_delay(struct regulator_dev *rdev,
 	return 0;
 }
 
-static int lp873x_buck_set_current_limit(struct regulator_dev *rdev,
-					 int min_uA, int max_uA)
-{
-	int id = rdev_get_id(rdev);
-	struct lp873x *lp873 = rdev_get_drvdata(rdev);
-	int i;
-
-	for (i = ARRAY_SIZE(lp873x_buck_uA) - 1; i >= 0; i--) {
-		if (lp873x_buck_uA[i] >= min_uA &&
-		    lp873x_buck_uA[i] <= max_uA)
-			return regmap_update_bits(lp873->regmap,
-						  regulators[id].ctrl2_reg,
-						  LP873X_BUCK0_CTRL_2_BUCK0_ILIM,
-						  i << __ffs(LP873X_BUCK0_CTRL_2_BUCK0_ILIM));
-	}
-
-	return -EINVAL;
-}
-
-static int lp873x_buck_get_current_limit(struct regulator_dev *rdev)
-{
-	int id = rdev_get_id(rdev);
-	struct lp873x *lp873 = rdev_get_drvdata(rdev);
-	int ret;
-	unsigned int val;
-
-	ret = regmap_read(lp873->regmap, regulators[id].ctrl2_reg, &val);
-	if (ret)
-		return ret;
-
-	val = (val & LP873X_BUCK0_CTRL_2_BUCK0_ILIM) >>
-	       __ffs(LP873X_BUCK0_CTRL_2_BUCK0_ILIM);
-
-	return (val < ARRAY_SIZE(lp873x_buck_uA)) ?
-			lp873x_buck_uA[val] : -EINVAL;
-}
-
 /* Operations permitted on BUCK0, BUCK1 */
-static struct regulator_ops lp873x_buck01_ops = {
+static const struct regulator_ops lp873x_buck01_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
@@ -156,12 +123,12 @@ static struct regulator_ops lp873x_buck01_ops = {
 	.map_voltage		= regulator_map_voltage_linear_range,
 	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
 	.set_ramp_delay		= lp873x_buck_set_ramp_delay,
-	.set_current_limit	= lp873x_buck_set_current_limit,
-	.get_current_limit	= lp873x_buck_get_current_limit,
+	.set_current_limit	= regulator_set_current_limit_regmap,
+	.get_current_limit	= regulator_get_current_limit_regmap,
 };
 
 /* Operations permitted on LDO0 and LDO1 */
-static struct regulator_ops lp873x_ldo01_ops = {
+static const struct regulator_ops lp873x_ldo01_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
diff --git a/drivers/regulator/lp8755.c b/drivers/regulator/lp8755.c
index 244822bb63cd..14fd38807134 100644
--- a/drivers/regulator/lp8755.c
+++ b/drivers/regulator/lp8755.c
@@ -315,7 +315,7 @@ out_i2c_error:
 	.vsel_mask = LP8755_BUCK_VOUT_M,\
 }
 
-static struct regulator_desc lp8755_regulators[] = {
+static const struct regulator_desc lp8755_regulators[] = {
 	lp8755_buck_desc(0),
 	lp8755_buck_desc(1),
 	lp8755_buck_desc(2),
@@ -386,7 +386,7 @@ static irqreturn_t lp8755_irq_handler(int irq, void *data)
 	if (ret < 0)
 		goto err_i2c;
 
-	/* send OCP event to all regualtor devices */
+	/* send OCP event to all regulator devices */
 	if ((flag1 & 0x01) && (pchip->irqmask & 0x01))
 		for (icnt = 0; icnt < LP8755_BUCK_MAX; icnt++)
 			if (pchip->rdev[icnt] != NULL)
@@ -394,7 +394,7 @@ static irqreturn_t lp8755_irq_handler(int irq, void *data)
 							      LP8755_EVENT_OCP,
 							      NULL);
 
-	/* send OVP event to all regualtor devices */
+	/* send OVP event to all regulator devices */
 	if ((flag1 & 0x02) && (pchip->irqmask & 0x02))
 		for (icnt = 0; icnt < LP8755_BUCK_MAX; icnt++)
 			if (pchip->rdev[icnt] != NULL)
diff --git a/drivers/regulator/lp87565-regulator.c b/drivers/regulator/lp87565-regulator.c
index c192357d1dea..4ed41731a5b1 100644
--- a/drivers/regulator/lp87565-regulator.c
+++ b/drivers/regulator/lp87565-regulator.c
@@ -51,7 +51,7 @@ static const struct regulator_linear_range buck0_1_2_3_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1420000, 0x9e, 0xff, 20000),
 };
 
-static unsigned int lp87565_buck_ramp_delay[] = {
+static const unsigned int lp87565_buck_ramp_delay[] = {
 	30000, 15000, 10000, 7500, 3800, 1900, 940, 470
 };
 
@@ -140,7 +140,7 @@ static int lp87565_buck_get_current_limit(struct regulator_dev *rdev)
 }
 
 /* Operations permitted on BUCK0, BUCK1 */
-static struct regulator_ops lp87565_buck_ops = {
+static const struct regulator_ops lp87565_buck_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
diff --git a/drivers/regulator/lp8788-buck.c b/drivers/regulator/lp8788-buck.c
index ec46290b647e..a7d30550bb5f 100644
--- a/drivers/regulator/lp8788-buck.c
+++ b/drivers/regulator/lp8788-buck.c
@@ -95,12 +95,10 @@ struct lp8788_buck {
 	void *dvs;
 };
 
-/* BUCK 1 ~ 4 voltage table */
-static const int lp8788_buck_vtbl[] = {
-	 500000,  800000,  850000,  900000,  950000, 1000000, 1050000, 1100000,
-	1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
-	1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000, 1900000,
-	1950000, 2000000,
+/* BUCK 1 ~ 4 voltage ranges */
+static const struct regulator_linear_range buck_volt_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000, 0, 0, 0),
+	REGULATOR_LINEAR_RANGE(800000, 1, 25, 50000),
 };
 
 static void lp8788_buck1_set_dvs(struct lp8788_buck *buck)
@@ -345,8 +343,8 @@ static unsigned int lp8788_buck_get_mode(struct regulator_dev *rdev)
 }
 
 static const struct regulator_ops lp8788_buck12_ops = {
-	.list_voltage = regulator_list_voltage_table,
-	.map_voltage = regulator_map_voltage_ascend,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
 	.set_voltage_sel = lp8788_buck12_set_voltage_sel,
 	.get_voltage_sel = lp8788_buck12_get_voltage_sel,
 	.enable = regulator_enable_regmap,
@@ -358,8 +356,8 @@ static const struct regulator_ops lp8788_buck12_ops = {
 };
 
 static const struct regulator_ops lp8788_buck34_ops = {
-	.list_voltage = regulator_list_voltage_table,
-	.map_voltage = regulator_map_voltage_ascend,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.enable = regulator_enable_regmap,
@@ -370,13 +368,14 @@ static const struct regulator_ops lp8788_buck34_ops = {
 	.get_mode = lp8788_buck_get_mode,
 };
 
-static struct regulator_desc lp8788_buck_desc[] = {
+static const struct regulator_desc lp8788_buck_desc[] = {
 	{
 		.name = "buck1",
 		.id = BUCK1,
 		.ops = &lp8788_buck12_ops,
-		.n_voltages = ARRAY_SIZE(lp8788_buck_vtbl),
-		.volt_table = lp8788_buck_vtbl,
+		.n_voltages = 26,
+		.linear_ranges = buck_volt_ranges,
+		.n_linear_ranges = ARRAY_SIZE(buck_volt_ranges),
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 		.enable_reg = LP8788_EN_BUCK,
@@ -386,8 +385,9 @@ static struct regulator_desc lp8788_buck_desc[] = {
 		.name = "buck2",
 		.id = BUCK2,
 		.ops = &lp8788_buck12_ops,
-		.n_voltages = ARRAY_SIZE(lp8788_buck_vtbl),
-		.volt_table = lp8788_buck_vtbl,
+		.n_voltages = 26,
+		.linear_ranges = buck_volt_ranges,
+		.n_linear_ranges = ARRAY_SIZE(buck_volt_ranges),
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 		.enable_reg = LP8788_EN_BUCK,
@@ -397,8 +397,9 @@ static struct regulator_desc lp8788_buck_desc[] = {
 		.name = "buck3",
 		.id = BUCK3,
 		.ops = &lp8788_buck34_ops,
-		.n_voltages = ARRAY_SIZE(lp8788_buck_vtbl),
-		.volt_table = lp8788_buck_vtbl,
+		.n_voltages = 26,
+		.linear_ranges = buck_volt_ranges,
+		.n_linear_ranges = ARRAY_SIZE(buck_volt_ranges),
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 		.vsel_reg = LP8788_BUCK3_VOUT,
@@ -410,8 +411,9 @@ static struct regulator_desc lp8788_buck_desc[] = {
 		.name = "buck4",
 		.id = BUCK4,
 		.ops = &lp8788_buck34_ops,
-		.n_voltages = ARRAY_SIZE(lp8788_buck_vtbl),
-		.volt_table = lp8788_buck_vtbl,
+		.n_voltages = 26,
+		.linear_ranges = buck_volt_ranges,
+		.n_linear_ranges = ARRAY_SIZE(buck_volt_ranges),
 		.type = REGULATOR_VOLTAGE,
 		.owner = THIS_MODULE,
 		.vsel_reg = LP8788_BUCK4_VOUT,
diff --git a/drivers/regulator/lp8788-ldo.c b/drivers/regulator/lp8788-ldo.c
index 2ee22e7ea675..a2ef146e6b3a 100644
--- a/drivers/regulator/lp8788-ldo.c
+++ b/drivers/regulator/lp8788-ldo.c
@@ -186,7 +186,7 @@ static const struct regulator_ops lp8788_ldo_voltage_fixed_ops = {
 	.enable_time = lp8788_ldo_enable_time,
 };
 
-static struct regulator_desc lp8788_dldo_desc[] = {
+static const struct regulator_desc lp8788_dldo_desc[] = {
 	{
 		.name = "dldo1",
 		.id = DLDO1,
@@ -343,7 +343,7 @@ static struct regulator_desc lp8788_dldo_desc[] = {
 	},
 };
 
-static struct regulator_desc lp8788_aldo_desc[] = {
+static const struct regulator_desc lp8788_aldo_desc[] = {
 	{
 		.name = "aldo1",
 		.id = ALDO1,
diff --git a/drivers/regulator/ltc3676.c b/drivers/regulator/ltc3676.c
index 71fd0f2a4b76..e6d66e492b85 100644
--- a/drivers/regulator/ltc3676.c
+++ b/drivers/regulator/ltc3676.c
@@ -241,61 +241,10 @@ static struct regulator_desc ltc3676_regulators[LTC3676_NUM_REGULATORS] = {
 	LTC3676_FIXED_REG(LDO4, ldo4, LDOB, 2),
 };
 
-static bool ltc3676_writeable_reg(struct device *dev, unsigned int reg)
+static bool ltc3676_readable_writeable_reg(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
-	case LTC3676_IRQSTAT:
-	case LTC3676_BUCK1:
-	case LTC3676_BUCK2:
-	case LTC3676_BUCK3:
-	case LTC3676_BUCK4:
-	case LTC3676_LDOA:
-	case LTC3676_LDOB:
-	case LTC3676_SQD1:
-	case LTC3676_SQD2:
-	case LTC3676_CNTRL:
-	case LTC3676_DVB1A:
-	case LTC3676_DVB1B:
-	case LTC3676_DVB2A:
-	case LTC3676_DVB2B:
-	case LTC3676_DVB3A:
-	case LTC3676_DVB3B:
-	case LTC3676_DVB4A:
-	case LTC3676_DVB4B:
-	case LTC3676_MSKIRQ:
-	case LTC3676_MSKPG:
-	case LTC3676_USER:
-	case LTC3676_HRST:
-	case LTC3676_CLIRQ:
-		return true;
-	}
-	return false;
-}
-
-static bool ltc3676_readable_reg(struct device *dev, unsigned int reg)
-{
-	switch (reg) {
-	case LTC3676_IRQSTAT:
-	case LTC3676_BUCK1:
-	case LTC3676_BUCK2:
-	case LTC3676_BUCK3:
-	case LTC3676_BUCK4:
-	case LTC3676_LDOA:
-	case LTC3676_LDOB:
-	case LTC3676_SQD1:
-	case LTC3676_SQD2:
-	case LTC3676_CNTRL:
-	case LTC3676_DVB1A:
-	case LTC3676_DVB1B:
-	case LTC3676_DVB2A:
-	case LTC3676_DVB2B:
-	case LTC3676_DVB3A:
-	case LTC3676_DVB3B:
-	case LTC3676_DVB4A:
-	case LTC3676_DVB4B:
-	case LTC3676_MSKIRQ:
-	case LTC3676_MSKPG:
-	case LTC3676_USER:
+	case LTC3676_BUCK1 ... LTC3676_IRQSTAT:
 	case LTC3676_HRST:
 	case LTC3676_CLIRQ:
 		return true;
@@ -306,9 +255,7 @@ static bool ltc3676_readable_reg(struct device *dev, unsigned int reg)
 static bool ltc3676_volatile_reg(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
-	case LTC3676_IRQSTAT:
-	case LTC3676_PGSTATL:
-	case LTC3676_PGSTATRT:
+	case LTC3676_IRQSTAT ... LTC3676_PGSTATRT:
 		return true;
 	}
 	return false;
@@ -317,8 +264,8 @@ static bool ltc3676_volatile_reg(struct device *dev, unsigned int reg)
 static const struct regmap_config ltc3676_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
-	.writeable_reg = ltc3676_writeable_reg,
-	.readable_reg = ltc3676_readable_reg,
+	.writeable_reg = ltc3676_readable_writeable_reg,
+	.readable_reg = ltc3676_readable_writeable_reg,
 	.volatile_reg = ltc3676_volatile_reg,
 	.max_register = LTC3676_CLIRQ,
 	.use_single_read = true,
@@ -442,5 +389,5 @@ static struct i2c_driver ltc3676_driver = {
 module_i2c_driver(ltc3676_driver);
 
 MODULE_AUTHOR("Tim Harvey <tharvey@gateworks.com>");
-MODULE_DESCRIPTION("Regulator driver for Linear Technology LTC1376");
+MODULE_DESCRIPTION("Regulator driver for Linear Technology LTC3676");
 MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/max14577-regulator.c b/drivers/regulator/max14577-regulator.c
index bc7f4751bf9c..85a88a9e4d42 100644
--- a/drivers/regulator/max14577-regulator.c
+++ b/drivers/regulator/max14577-regulator.c
@@ -324,4 +324,3 @@ module_exit(max14577_regulator_exit);
 MODULE_AUTHOR("Krzysztof Kozlowski <krzk@kernel.org>");
 MODULE_DESCRIPTION("Maxim 14577/77836 regulator driver");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:max14577-regulator");
diff --git a/drivers/regulator/max77620-regulator.c b/drivers/regulator/max77620-regulator.c
index cd93cf53e23c..1607ac673e44 100644
--- a/drivers/regulator/max77620-regulator.c
+++ b/drivers/regulator/max77620-regulator.c
@@ -690,6 +690,7 @@ static const struct regulator_ops max77620_regulator_ops = {
 			.active_discharge_mask = MAX77620_SD_CFG1_ADE_MASK, \
 			.active_discharge_reg = MAX77620_REG_##_id##_CFG, \
 			.type = REGULATOR_VOLTAGE,			\
+			.owner = THIS_MODULE,				\
 		},							\
 	}
 
@@ -721,6 +722,7 @@ static const struct regulator_ops max77620_regulator_ops = {
 			.active_discharge_mask = MAX77620_LDO_CFG2_ADE_MASK, \
 			.active_discharge_reg = MAX77620_REG_##_id##_CFG2, \
 			.type = REGULATOR_VOLTAGE,			\
+			.owner = THIS_MODULE,				\
 		},							\
 	}
 
diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c
new file mode 100644
index 000000000000..31ebf34b01ec
--- /dev/null
+++ b/drivers/regulator/max77650-regulator.c
@@ -0,0 +1,498 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// Regulator driver for MAXIM 77650/77651 charger/power-supply.
+
+#include <linux/of.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
+#define MAX77650_REGULATOR_EN_CTRL_MASK		GENMASK(3, 0)
+#define MAX77650_REGULATOR_EN_CTRL_BITS(_reg) \
+		((_reg) & MAX77650_REGULATOR_EN_CTRL_MASK)
+#define MAX77650_REGULATOR_ENABLED		GENMASK(2, 1)
+#define MAX77650_REGULATOR_DISABLED		BIT(2)
+
+#define MAX77650_REGULATOR_V_LDO_MASK		GENMASK(6, 0)
+#define MAX77650_REGULATOR_V_SBB_MASK		GENMASK(5, 0)
+
+#define MAX77650_REGULATOR_AD_MASK		BIT(3)
+#define MAX77650_REGULATOR_AD_DISABLED		0x00
+#define MAX77650_REGULATOR_AD_ENABLED		BIT(3)
+
+#define MAX77650_REGULATOR_CURR_LIM_MASK	GENMASK(7, 6)
+
+enum {
+	MAX77650_REGULATOR_ID_LDO = 0,
+	MAX77650_REGULATOR_ID_SBB0,
+	MAX77650_REGULATOR_ID_SBB1,
+	MAX77650_REGULATOR_ID_SBB2,
+	MAX77650_REGULATOR_NUM_REGULATORS,
+};
+
+struct max77650_regulator_desc {
+	struct regulator_desc desc;
+	unsigned int regA;
+	unsigned int regB;
+};
+
+static const u32 max77651_sbb1_regulator_volt_table[] = {
+	2400000, 3200000, 4000000, 4800000,
+	2450000, 3250000, 4050000, 4850000,
+	2500000, 3300000, 4100000, 4900000,
+	2550000, 3350000, 4150000, 4950000,
+	2600000, 3400000, 4200000, 5000000,
+	2650000, 3450000, 4250000, 5050000,
+	2700000, 3500000, 4300000, 5100000,
+	2750000, 3550000, 4350000, 5150000,
+	2800000, 3600000, 4400000, 5200000,
+	2850000, 3650000, 4450000, 5250000,
+	2900000, 3700000, 4500000,       0,
+	2950000, 3750000, 4550000,       0,
+	3000000, 3800000, 4600000,       0,
+	3050000, 3850000, 4650000,       0,
+	3100000, 3900000, 4700000,       0,
+	3150000, 3950000, 4750000,       0,
+};
+
+#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
+		(((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
+#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
+		(((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
+
+#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val)				\
+	do {								\
+		_val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val);		\
+		_val--;							\
+		_val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val);		\
+	} while (0)
+
+#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val)				\
+	do {								\
+		_val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val);		\
+		_val++;							\
+		_val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val);		\
+	} while (0)
+
+static const unsigned int max77650_current_limit_table[] = {
+	1000000, 866000, 707000, 500000,
+};
+
+static int max77650_regulator_is_enabled(struct regulator_dev *rdev)
+{
+	struct max77650_regulator_desc *rdesc;
+	struct regmap *map;
+	int val, rv, en;
+
+	rdesc = rdev_get_drvdata(rdev);
+	map = rdev_get_regmap(rdev);
+
+	rv = regmap_read(map, rdesc->regB, &val);
+	if (rv)
+		return rv;
+
+	en = MAX77650_REGULATOR_EN_CTRL_BITS(val);
+
+	return en != MAX77650_REGULATOR_DISABLED;
+}
+
+static int max77650_regulator_enable(struct regulator_dev *rdev)
+{
+	struct max77650_regulator_desc *rdesc;
+	struct regmap *map;
+
+	rdesc = rdev_get_drvdata(rdev);
+	map = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(map, rdesc->regB,
+				  MAX77650_REGULATOR_EN_CTRL_MASK,
+				  MAX77650_REGULATOR_ENABLED);
+}
+
+static int max77650_regulator_disable(struct regulator_dev *rdev)
+{
+	struct max77650_regulator_desc *rdesc;
+	struct regmap *map;
+
+	rdesc = rdev_get_drvdata(rdev);
+	map = rdev_get_regmap(rdev);
+
+	return regmap_update_bits(map, rdesc->regB,
+				  MAX77650_REGULATOR_EN_CTRL_MASK,
+				  MAX77650_REGULATOR_DISABLED);
+}
+
+static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
+					      unsigned int sel)
+{
+	int rv = 0, curr, diff;
+	bool ascending;
+
+	/*
+	 * If the regulator is disabled, we can program the desired
+	 * voltage right away.
+	 */
+	if (!max77650_regulator_is_enabled(rdev))
+		return regulator_set_voltage_sel_regmap(rdev, sel);
+
+	/*
+	 * Otherwise we need to manually ramp the output voltage up/down
+	 * one step at a time.
+	 */
+
+	curr = regulator_get_voltage_sel_regmap(rdev);
+	if (curr < 0)
+		return curr;
+
+	diff = curr - sel;
+	if (diff == 0)
+		return 0; /* Already there. */
+	else if (diff > 0)
+		ascending = false;
+	else
+		ascending = true;
+
+	/*
+	 * Make sure we'll get to the right voltage and break the loop even if
+	 * the selector equals 0.
+	 */
+	for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
+		rv = regulator_set_voltage_sel_regmap(rdev, curr);
+		if (rv)
+			return rv;
+
+		if (curr == sel)
+			break;
+	}
+
+	return 0;
+}
+
+/*
+ * Special case: non-linear voltage table for max77651 SBB1 - software
+ * must ensure the voltage is ramped in 50mV increments.
+ */
+static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
+						   unsigned int sel)
+{
+	int rv = 0, curr, vcurr, vdest, vdiff;
+
+	/*
+	 * If the regulator is disabled, we can program the desired
+	 * voltage right away.
+	 */
+	if (!max77650_regulator_is_enabled(rdev))
+		return regulator_set_voltage_sel_regmap(rdev, sel);
+
+	curr = regulator_get_voltage_sel_regmap(rdev);
+	if (curr < 0)
+		return curr;
+
+	if (curr == sel)
+		return 0; /* Already there. */
+
+	vcurr = max77651_sbb1_regulator_volt_table[curr];
+	vdest = max77651_sbb1_regulator_volt_table[sel];
+	vdiff = vcurr - vdest;
+
+	for (;;) {
+		if (vdiff > 0)
+			MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
+		else
+			MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
+
+		rv = regulator_set_voltage_sel_regmap(rdev, curr);
+		if (rv)
+			return rv;
+
+		if (curr == sel)
+			break;
+	};
+
+	return 0;
+}
+
+static const struct regulator_ops max77650_regulator_LDO_ops = {
+	.is_enabled		= max77650_regulator_is_enabled,
+	.enable			= max77650_regulator_enable,
+	.disable		= max77650_regulator_disable,
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= max77650_regulator_set_voltage_sel,
+	.set_active_discharge	= regulator_set_active_discharge_regmap,
+};
+
+static const struct regulator_ops max77650_regulator_SBB_ops = {
+	.is_enabled		= max77650_regulator_is_enabled,
+	.enable			= max77650_regulator_enable,
+	.disable		= max77650_regulator_disable,
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= max77650_regulator_set_voltage_sel,
+	.get_current_limit	= regulator_get_current_limit_regmap,
+	.set_current_limit	= regulator_set_current_limit_regmap,
+	.set_active_discharge	= regulator_set_active_discharge_regmap,
+};
+
+/* Special case for max77651 SBB1 - non-linear voltage mapping. */
+static const struct regulator_ops max77651_SBB1_regulator_ops = {
+	.is_enabled		= max77650_regulator_is_enabled,
+	.enable			= max77650_regulator_enable,
+	.disable		= max77650_regulator_disable,
+	.list_voltage		= regulator_list_voltage_table,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= max77651_regulator_sbb1_set_voltage_sel,
+	.get_current_limit	= regulator_get_current_limit_regmap,
+	.set_current_limit	= regulator_set_current_limit_regmap,
+	.set_active_discharge	= regulator_set_active_discharge_regmap,
+};
+
+static struct max77650_regulator_desc max77650_LDO_desc = {
+	.desc = {
+		.name			= "ldo",
+		.of_match		= of_match_ptr("ldo"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-ldo",
+		.id			= MAX77650_REGULATOR_ID_LDO,
+		.ops			= &max77650_regulator_LDO_ops,
+		.min_uV			= 1350000,
+		.uV_step		= 12500,
+		.n_voltages		= 128,
+		.vsel_mask		= MAX77650_REGULATOR_V_LDO_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_LDO_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_LDO_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+	},
+	.regA		= MAX77650_REG_CNFG_LDO_A,
+	.regB		= MAX77650_REG_CNFG_LDO_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB0_desc = {
+	.desc = {
+		.name			= "sbb0",
+		.of_match		= of_match_ptr("sbb0"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-sbb0",
+		.id			= MAX77650_REGULATOR_ID_SBB0,
+		.ops			= &max77650_regulator_SBB_ops,
+		.min_uV			= 800000,
+		.uV_step		= 25000,
+		.n_voltages		= 64,
+		.vsel_mask		= MAX77650_REGULATOR_V_SBB_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_SBB0_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_SBB0_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+		.csel_reg		= MAX77650_REG_CNFG_SBB0_A,
+		.csel_mask		= MAX77650_REGULATOR_CURR_LIM_MASK,
+		.curr_table		= max77650_current_limit_table,
+		.n_current_limits = ARRAY_SIZE(max77650_current_limit_table),
+	},
+	.regA		= MAX77650_REG_CNFG_SBB0_A,
+	.regB		= MAX77650_REG_CNFG_SBB0_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB1_desc = {
+	.desc = {
+		.name			= "sbb1",
+		.of_match		= of_match_ptr("sbb1"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-sbb1",
+		.id			= MAX77650_REGULATOR_ID_SBB1,
+		.ops			= &max77650_regulator_SBB_ops,
+		.min_uV			= 800000,
+		.uV_step		= 12500,
+		.n_voltages		= 64,
+		.vsel_mask		= MAX77650_REGULATOR_V_SBB_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_SBB1_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_SBB1_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+		.csel_reg		= MAX77650_REG_CNFG_SBB1_A,
+		.csel_mask		= MAX77650_REGULATOR_CURR_LIM_MASK,
+		.curr_table		= max77650_current_limit_table,
+		.n_current_limits = ARRAY_SIZE(max77650_current_limit_table),
+	},
+	.regA		= MAX77650_REG_CNFG_SBB1_A,
+	.regB		= MAX77650_REG_CNFG_SBB1_B,
+};
+
+static struct max77650_regulator_desc max77651_SBB1_desc = {
+	.desc = {
+		.name			= "sbb1",
+		.of_match		= of_match_ptr("sbb1"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-sbb1",
+		.id			= MAX77650_REGULATOR_ID_SBB1,
+		.ops			= &max77651_SBB1_regulator_ops,
+		.volt_table		= max77651_sbb1_regulator_volt_table,
+		.n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
+		.vsel_mask		= MAX77650_REGULATOR_V_SBB_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_SBB1_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_SBB1_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+		.csel_reg		= MAX77650_REG_CNFG_SBB1_A,
+		.csel_mask		= MAX77650_REGULATOR_CURR_LIM_MASK,
+		.curr_table		= max77650_current_limit_table,
+		.n_current_limits = ARRAY_SIZE(max77650_current_limit_table),
+	},
+	.regA		= MAX77650_REG_CNFG_SBB1_A,
+	.regB		= MAX77650_REG_CNFG_SBB1_B,
+};
+
+static struct max77650_regulator_desc max77650_SBB2_desc = {
+	.desc = {
+		.name			= "sbb2",
+		.of_match		= of_match_ptr("sbb2"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-sbb0",
+		.id			= MAX77650_REGULATOR_ID_SBB2,
+		.ops			= &max77650_regulator_SBB_ops,
+		.min_uV			= 800000,
+		.uV_step		= 50000,
+		.n_voltages		= 64,
+		.vsel_mask		= MAX77650_REGULATOR_V_SBB_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_SBB2_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_SBB2_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+		.csel_reg		= MAX77650_REG_CNFG_SBB2_A,
+		.csel_mask		= MAX77650_REGULATOR_CURR_LIM_MASK,
+		.curr_table		= max77650_current_limit_table,
+		.n_current_limits = ARRAY_SIZE(max77650_current_limit_table),
+	},
+	.regA		= MAX77650_REG_CNFG_SBB2_A,
+	.regB		= MAX77650_REG_CNFG_SBB2_B,
+};
+
+static struct max77650_regulator_desc max77651_SBB2_desc = {
+	.desc = {
+		.name			= "sbb2",
+		.of_match		= of_match_ptr("sbb2"),
+		.regulators_node	= of_match_ptr("regulators"),
+		.supply_name		= "in-sbb0",
+		.id			= MAX77650_REGULATOR_ID_SBB2,
+		.ops			= &max77650_regulator_SBB_ops,
+		.min_uV			= 2400000,
+		.uV_step		= 50000,
+		.n_voltages		= 64,
+		.vsel_mask		= MAX77650_REGULATOR_V_SBB_MASK,
+		.vsel_reg		= MAX77650_REG_CNFG_SBB2_A,
+		.active_discharge_off	= MAX77650_REGULATOR_AD_DISABLED,
+		.active_discharge_on	= MAX77650_REGULATOR_AD_ENABLED,
+		.active_discharge_mask	= MAX77650_REGULATOR_AD_MASK,
+		.active_discharge_reg	= MAX77650_REG_CNFG_SBB2_B,
+		.enable_time		= 100,
+		.type			= REGULATOR_VOLTAGE,
+		.owner			= THIS_MODULE,
+		.csel_reg		= MAX77650_REG_CNFG_SBB2_A,
+		.csel_mask		= MAX77650_REGULATOR_CURR_LIM_MASK,
+		.curr_table		= max77650_current_limit_table,
+		.n_current_limits = ARRAY_SIZE(max77650_current_limit_table),
+	},
+	.regA		= MAX77650_REG_CNFG_SBB2_A,
+	.regB		= MAX77650_REG_CNFG_SBB2_B,
+};
+
+static int max77650_regulator_probe(struct platform_device *pdev)
+{
+	struct max77650_regulator_desc **rdescs;
+	struct max77650_regulator_desc *rdesc;
+	struct regulator_config config = { };
+	struct device *dev, *parent;
+	struct regulator_dev *rdev;
+	struct regmap *map;
+	unsigned int val;
+	int i, rv;
+
+	dev = &pdev->dev;
+	parent = dev->parent;
+
+	if (!dev->of_node)
+		dev->of_node = parent->of_node;
+
+	rdescs = devm_kcalloc(dev, MAX77650_REGULATOR_NUM_REGULATORS,
+			      sizeof(*rdescs), GFP_KERNEL);
+	if (!rdescs)
+		return -ENOMEM;
+
+	map = dev_get_regmap(parent, NULL);
+	if (!map)
+		return -ENODEV;
+
+	rv = regmap_read(map, MAX77650_REG_CID, &val);
+	if (rv)
+		return rv;
+
+	rdescs[MAX77650_REGULATOR_ID_LDO] = &max77650_LDO_desc;
+	rdescs[MAX77650_REGULATOR_ID_SBB0] = &max77650_SBB0_desc;
+
+	switch (MAX77650_CID_BITS(val)) {
+	case MAX77650_CID_77650A:
+	case MAX77650_CID_77650C:
+		rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77650_SBB1_desc;
+		rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77650_SBB2_desc;
+		break;
+	case MAX77650_CID_77651A:
+	case MAX77650_CID_77651B:
+		rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77651_SBB1_desc;
+		rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77651_SBB2_desc;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	config.dev = parent;
+
+	for (i = 0; i < MAX77650_REGULATOR_NUM_REGULATORS; i++) {
+		rdesc = rdescs[i];
+		config.driver_data = rdesc;
+
+		rdev = devm_regulator_register(dev, &rdesc->desc, &config);
+		if (IS_ERR(rdev))
+			return PTR_ERR(rdev);
+	}
+
+	return 0;
+}
+
+static struct platform_driver max77650_regulator_driver = {
+	.driver = {
+		.name = "max77650-regulator",
+	},
+	.probe = max77650_regulator_probe,
+};
+module_platform_driver(max77650_regulator_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 regulator driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/max77802-regulator.c b/drivers/regulator/max77802-regulator.c
index c30cf5c9f2de..ea7b50397300 100644
--- a/drivers/regulator/max77802-regulator.c
+++ b/drivers/regulator/max77802-regulator.c
@@ -248,9 +248,9 @@ static int max77802_set_ramp_delay_2bit(struct regulator_dev *rdev,
 	unsigned int ramp_value;
 
 	if (id > MAX77802_BUCK4) {
-			dev_warn(&rdev->dev,
-				 "%s: regulator: ramp delay not supported\n",
-				 rdev->desc->name);
+		dev_warn(&rdev->dev,
+			 "%s: regulator: ramp delay not supported\n",
+			 rdev->desc->name);
 		return -EINVAL;
 	}
 	ramp_value = max77802_find_ramp_value(rdev, ramp_table_77802_2bit,
diff --git a/drivers/regulator/mc13783-regulator.c b/drivers/regulator/mc13783-regulator.c
index 887a1d1726ad..ab558b26cd7c 100644
--- a/drivers/regulator/mc13783-regulator.c
+++ b/drivers/regulator/mc13783-regulator.c
@@ -226,7 +226,7 @@ static const unsigned int mc13783_pwgtdrv_val[] = {
 	5500000,
 };
 
-static struct regulator_ops mc13783_gpo_regulator_ops;
+static const struct regulator_ops mc13783_gpo_regulator_ops;
 
 #define MC13783_DEFINE(prefix, name, node, reg, vsel_reg, voltages)	\
 	MC13xxx_DEFINE(MC13783_REG_, name, node, reg, vsel_reg, voltages, \
@@ -380,7 +380,7 @@ static int mc13783_gpo_regulator_is_enabled(struct regulator_dev *rdev)
 	return (val & mc13xxx_regulators[id].enable_bit) != 0;
 }
 
-static struct regulator_ops mc13783_gpo_regulator_ops = {
+static const struct regulator_ops mc13783_gpo_regulator_ops = {
 	.enable = mc13783_gpo_regulator_enable,
 	.disable = mc13783_gpo_regulator_disable,
 	.is_enabled = mc13783_gpo_regulator_is_enabled,
diff --git a/drivers/regulator/mc13892-regulator.c b/drivers/regulator/mc13892-regulator.c
index b55894980066..a731e826a037 100644
--- a/drivers/regulator/mc13892-regulator.c
+++ b/drivers/regulator/mc13892-regulator.c
@@ -242,8 +242,8 @@ static const unsigned int mc13892_pwgtdrv[] = {
 	5000000,
 };
 
-static struct regulator_ops mc13892_gpo_regulator_ops;
-static struct regulator_ops mc13892_sw_regulator_ops;
+static const struct regulator_ops mc13892_gpo_regulator_ops;
+static const struct regulator_ops mc13892_sw_regulator_ops;
 
 
 #define MC13892_FIXED_DEFINE(name, node, reg, voltages)			\
@@ -387,7 +387,7 @@ static int mc13892_gpo_regulator_is_enabled(struct regulator_dev *rdev)
 }
 
 
-static struct regulator_ops mc13892_gpo_regulator_ops = {
+static const struct regulator_ops mc13892_gpo_regulator_ops = {
 	.enable = mc13892_gpo_regulator_enable,
 	.disable = mc13892_gpo_regulator_disable,
 	.is_enabled = mc13892_gpo_regulator_is_enabled,
@@ -479,7 +479,7 @@ static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev,
 	return ret;
 }
 
-static struct regulator_ops mc13892_sw_regulator_ops = {
+static const struct regulator_ops mc13892_sw_regulator_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_ascend,
 	.set_voltage_sel = mc13892_sw_regulator_set_voltage_sel,
diff --git a/drivers/regulator/mc13xxx-regulator-core.c b/drivers/regulator/mc13xxx-regulator-core.c
index 2243138d8a58..8ff19150ca92 100644
--- a/drivers/regulator/mc13xxx-regulator-core.c
+++ b/drivers/regulator/mc13xxx-regulator-core.c
@@ -99,7 +99,7 @@ static int mc13xxx_regulator_get_voltage(struct regulator_dev *rdev)
 	return rdev->desc->volt_table[val];
 }
 
-struct regulator_ops mc13xxx_regulator_ops = {
+const struct regulator_ops mc13xxx_regulator_ops = {
 	.enable = mc13xxx_regulator_enable,
 	.disable = mc13xxx_regulator_disable,
 	.is_enabled = mc13xxx_regulator_is_enabled,
@@ -127,7 +127,7 @@ int mc13xxx_fixed_regulator_set_voltage(struct regulator_dev *rdev, int min_uV,
 }
 EXPORT_SYMBOL_GPL(mc13xxx_fixed_regulator_set_voltage);
 
-struct regulator_ops mc13xxx_fixed_regulator_ops = {
+const struct regulator_ops mc13xxx_fixed_regulator_ops = {
 	.enable = mc13xxx_regulator_enable,
 	.disable = mc13xxx_regulator_disable,
 	.is_enabled = mc13xxx_regulator_is_enabled,
diff --git a/drivers/regulator/mc13xxx.h b/drivers/regulator/mc13xxx.h
index a602b08d4c9e..ba7eff1070bd 100644
--- a/drivers/regulator/mc13xxx.h
+++ b/drivers/regulator/mc13xxx.h
@@ -53,8 +53,8 @@ static inline struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
 }
 #endif
 
-extern struct regulator_ops mc13xxx_regulator_ops;
-extern struct regulator_ops mc13xxx_fixed_regulator_ops;
+extern const struct regulator_ops mc13xxx_regulator_ops;
+extern const struct regulator_ops mc13xxx_fixed_regulator_ops;
 
 #define MC13xxx_DEFINE(prefix, _name, _node, _reg, _vsel_reg, _voltages, _ops)	\
 	[prefix ## _name] = {				\
diff --git a/drivers/regulator/mcp16502.c b/drivers/regulator/mcp16502.c
index 3479ae009b0b..3a8004abe044 100644
--- a/drivers/regulator/mcp16502.c
+++ b/drivers/regulator/mcp16502.c
@@ -17,6 +17,7 @@
 #include <linux/regmap.h>
 #include <linux/regulator/driver.h>
 #include <linux/suspend.h>
+#include <linux/gpio/consumer.h>
 
 #define VDD_LOW_SEL 0x0D
 #define VDD_HIGH_SEL 0x3F
@@ -546,7 +547,6 @@ static struct i2c_driver mcp16502_drv = {
 
 module_i2c_driver(mcp16502_drv);
 
-MODULE_VERSION("1.0");
 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("MCP16502 PMIC driver");
 MODULE_AUTHOR("Andrei Stefanescu andrei.stefanescu@microchip.com");
diff --git a/drivers/regulator/mt6311-regulator.c b/drivers/regulator/mt6311-regulator.c
index 0495716fd35f..01d69f43d2b0 100644
--- a/drivers/regulator/mt6311-regulator.c
+++ b/drivers/regulator/mt6311-regulator.c
@@ -38,13 +38,9 @@ static const struct regmap_config mt6311_regmap_config = {
 #define MT6311_MAX_UV		1393750
 #define MT6311_STEP_UV		6250
 
-static const struct regulator_linear_range buck_volt_range[] = {
-	REGULATOR_LINEAR_RANGE(MT6311_MIN_UV, 0, 0x7f, MT6311_STEP_UV),
-};
-
 static const struct regulator_ops mt6311_buck_ops = {
-	.list_voltage = regulator_list_voltage_linear_range,
-	.map_voltage = regulator_map_voltage_linear_range,
+	.list_voltage = regulator_list_voltage_linear,
+	.map_voltage = regulator_map_voltage_linear,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
@@ -71,8 +67,6 @@ static const struct regulator_ops mt6311_ldo_ops = {
 	.min_uV = MT6311_MIN_UV,\
 	.uV_step = MT6311_STEP_UV,\
 	.owner = THIS_MODULE,\
-	.linear_ranges = buck_volt_range, \
-	.n_linear_ranges = ARRAY_SIZE(buck_volt_range), \
 	.enable_reg = MT6311_VDVFS11_CON9,\
 	.enable_mask = MT6311_PMIC_VDVFS11_EN_MASK,\
 	.vsel_reg = MT6311_VDVFS11_CON12,\
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index ffa5fc3724e4..7b6bf3536271 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -255,7 +255,7 @@ static void of_get_regulation_constraints(struct device_node *np,
  * @desc: regulator description
  *
  * Populates regulator_init_data structure by extracting data from device
- * tree node, returns a pointer to the populated struture or NULL if memory
+ * tree node, returns a pointer to the populated structure or NULL if memory
  * alloc fails.
  */
 struct regulator_init_data *of_get_regulator_init_data(struct device *dev,
@@ -547,7 +547,7 @@ bool of_check_coupling_data(struct regulator_dev *rdev)
 							  NULL);
 
 		if (c_n_phandles != n_phandles) {
-			dev_err(&rdev->dev, "number of couped reg phandles mismatch\n");
+			dev_err(&rdev->dev, "number of coupled reg phandles mismatch\n");
 			ret = false;
 			goto clean;
 		}
diff --git a/drivers/regulator/palmas-regulator.c b/drivers/regulator/palmas-regulator.c
index c2cc392a27d4..7fb9e8dd834e 100644
--- a/drivers/regulator/palmas-regulator.c
+++ b/drivers/regulator/palmas-regulator.c
@@ -382,7 +382,7 @@ static struct palmas_sleep_requestor_info tps65917_sleep_req_info[] = {
 	EXTERNAL_REQUESTOR_TPS65917(LDO5, 2, 4),
 };
 
-static unsigned int palmas_smps_ramp_delay[4] = {0, 10000, 5000, 2500};
+static const unsigned int palmas_smps_ramp_delay[4] = {0, 10000, 5000, 2500};
 
 #define SMPS_CTRL_MODE_OFF		0x00
 #define SMPS_CTRL_MODE_ON		0x01
diff --git a/drivers/regulator/pv88060-regulator.c b/drivers/regulator/pv88060-regulator.c
index 1f2d8180506b..1600f9821891 100644
--- a/drivers/regulator/pv88060-regulator.c
+++ b/drivers/regulator/pv88060-regulator.c
@@ -53,10 +53,6 @@ enum {
 
 struct pv88060_regulator {
 	struct regulator_desc desc;
-	/* Current limiting */
-	unsigned	n_current_limits;
-	const int	*current_limits;
-	unsigned int limit_mask;
 	unsigned int conf;		/* buck configuration register */
 };
 
@@ -75,7 +71,7 @@ static const struct regmap_config pv88060_regmap_config = {
  * Entry indexes corresponds to register values.
  */
 
-static const int pv88060_buck1_limits[] = {
+static const unsigned int pv88060_buck1_limits[] = {
 	1496000, 2393000, 3291000, 4189000
 };
 
@@ -128,40 +124,6 @@ static int pv88060_buck_set_mode(struct regulator_dev *rdev,
 					PV88060_BUCK_MODE_MASK, val);
 }
 
-static int pv88060_set_current_limit(struct regulator_dev *rdev, int min,
-				    int max)
-{
-	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
-	int i;
-
-	/* search for closest to maximum */
-	for (i = info->n_current_limits - 1; i >= 0; i--) {
-		if (min <= info->current_limits[i]
-			&& max >= info->current_limits[i]) {
-			return regmap_update_bits(rdev->regmap,
-				info->conf,
-				info->limit_mask,
-				i << PV88060_BUCK_ILIM_SHIFT);
-		}
-	}
-
-	return -EINVAL;
-}
-
-static int pv88060_get_current_limit(struct regulator_dev *rdev)
-{
-	struct pv88060_regulator *info = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret;
-
-	ret = regmap_read(rdev->regmap, info->conf, &data);
-	if (ret < 0)
-		return ret;
-
-	data = (data & info->limit_mask) >> PV88060_BUCK_ILIM_SHIFT;
-	return info->current_limits[data];
-}
-
 static const struct regulator_ops pv88060_buck_ops = {
 	.get_mode = pv88060_buck_get_mode,
 	.set_mode = pv88060_buck_set_mode,
@@ -171,8 +133,8 @@ static const struct regulator_ops pv88060_buck_ops = {
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.list_voltage = regulator_list_voltage_linear,
-	.set_current_limit = pv88060_set_current_limit,
-	.get_current_limit = pv88060_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 };
 
 static const struct regulator_ops pv88060_ldo_ops = {
@@ -184,6 +146,12 @@ static const struct regulator_ops pv88060_ldo_ops = {
 	.list_voltage = regulator_list_voltage_linear,
 };
 
+static const struct regulator_ops pv88060_sw_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
 #define PV88060_BUCK(chip, regl_name, min, step, max, limits_array) \
 {\
 	.desc	=	{\
@@ -201,10 +169,11 @@ static const struct regulator_ops pv88060_ldo_ops = {
 		.enable_mask = PV88060_BUCK_EN, \
 		.vsel_reg = PV88060_REG_##regl_name##_CONF0,\
 		.vsel_mask = PV88060_VBUCK_MASK,\
+		.curr_table = limits_array,\
+		.n_current_limits = ARRAY_SIZE(limits_array),\
+		.csel_reg = PV88060_REG_##regl_name##_CONF1,\
+		.csel_mask = PV88060_BUCK_ILIM_MASK,\
 	},\
-	.current_limits = limits_array,\
-	.n_current_limits = ARRAY_SIZE(limits_array),\
-	.limit_mask = PV88060_BUCK_ILIM_MASK, \
 	.conf = PV88060_REG_##regl_name##_CONF1,\
 }
 
@@ -237,9 +206,8 @@ static const struct regulator_ops pv88060_ldo_ops = {
 		.regulators_node = of_match_ptr("regulators"),\
 		.type = REGULATOR_VOLTAGE,\
 		.owner = THIS_MODULE,\
-		.ops = &pv88060_ldo_ops,\
-		.min_uV = max,\
-		.uV_step = 0,\
+		.ops = &pv88060_sw_ops,\
+		.fixed_uV = max,\
 		.n_voltages = 1,\
 		.enable_reg = PV88060_REG_##regl_name##_CONF,\
 		.enable_mask = PV88060_SW_EN,\
diff --git a/drivers/regulator/pv88080-regulator.c b/drivers/regulator/pv88080-regulator.c
index 6770e4de2097..bdddacdbeb99 100644
--- a/drivers/regulator/pv88080-regulator.c
+++ b/drivers/regulator/pv88080-regulator.c
@@ -45,12 +45,7 @@ enum pv88080_types {
 
 struct pv88080_regulator {
 	struct regulator_desc desc;
-	/* Current limiting */
-	unsigned int n_current_limits;
-	const int *current_limits;
-	unsigned int limit_mask;
 	unsigned int mode_reg;
-	unsigned int limit_reg;
 	unsigned int conf2;
 	unsigned int conf5;
 };
@@ -102,11 +97,11 @@ static const struct regmap_config pv88080_regmap_config = {
  * Entry indexes corresponds to register values.
  */
 
-static const int pv88080_buck1_limits[] = {
+static const unsigned int pv88080_buck1_limits[] = {
 	3230000, 5130000, 6960000, 8790000
 };
 
-static const int pv88080_buck23_limits[] = {
+static const unsigned int pv88080_buck23_limits[] = {
 	1496000, 2393000, 3291000, 4189000
 };
 
@@ -272,40 +267,6 @@ static int pv88080_buck_set_mode(struct regulator_dev *rdev,
 					PV88080_BUCK1_MODE_MASK, val);
 }
 
-static int pv88080_set_current_limit(struct regulator_dev *rdev, int min,
-				    int max)
-{
-	struct pv88080_regulator *info = rdev_get_drvdata(rdev);
-	int i;
-
-	/* search for closest to maximum */
-	for (i = info->n_current_limits - 1; i >= 0; i--) {
-		if (min <= info->current_limits[i]
-			&& max >= info->current_limits[i]) {
-				return regmap_update_bits(rdev->regmap,
-					info->limit_reg,
-					info->limit_mask,
-					i << PV88080_BUCK1_ILIM_SHIFT);
-		}
-	}
-
-	return -EINVAL;
-}
-
-static int pv88080_get_current_limit(struct regulator_dev *rdev)
-{
-	struct pv88080_regulator *info = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret;
-
-	ret = regmap_read(rdev->regmap, info->limit_reg, &data);
-	if (ret < 0)
-		return ret;
-
-	data = (data & info->limit_mask) >> PV88080_BUCK1_ILIM_SHIFT;
-	return info->current_limits[data];
-}
-
 static const struct regulator_ops pv88080_buck_ops = {
 	.get_mode = pv88080_buck_get_mode,
 	.set_mode = pv88080_buck_set_mode,
@@ -315,8 +276,8 @@ static const struct regulator_ops pv88080_buck_ops = {
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.list_voltage = regulator_list_voltage_linear,
-	.set_current_limit = pv88080_set_current_limit,
-	.get_current_limit = pv88080_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 };
 
 static const struct regulator_ops pv88080_hvbuck_ops = {
@@ -341,9 +302,9 @@ static const struct regulator_ops pv88080_hvbuck_ops = {
 		.min_uV = min, \
 		.uV_step = step, \
 		.n_voltages = ((max) - (min))/(step) + 1, \
+		.curr_table = limits_array, \
+		.n_current_limits = ARRAY_SIZE(limits_array), \
 	},\
-	.current_limits = limits_array, \
-	.n_current_limits = ARRAY_SIZE(limits_array), \
 }
 
 #define PV88080_HVBUCK(chip, regl_name, min, step, max) \
@@ -521,9 +482,9 @@ static int pv88080_i2c_probe(struct i2c_client *i2c,
 		if (init_data)
 			config.init_data = &init_data[i];
 
-		pv88080_regulator_info[i].limit_reg
+		pv88080_regulator_info[i].desc.csel_reg
 			= regmap_config->buck_regmap[i].buck_limit_reg;
-		pv88080_regulator_info[i].limit_mask
+		pv88080_regulator_info[i].desc.csel_mask
 			= regmap_config->buck_regmap[i].buck_limit_mask;
 		pv88080_regulator_info[i].mode_reg
 			= regmap_config->buck_regmap[i].buck_mode_reg;
diff --git a/drivers/regulator/pv88090-regulator.c b/drivers/regulator/pv88090-regulator.c
index 2302b0df7630..6e97cc6df2ee 100644
--- a/drivers/regulator/pv88090-regulator.c
+++ b/drivers/regulator/pv88090-regulator.c
@@ -42,10 +42,6 @@ enum {
 
 struct pv88090_regulator {
 	struct regulator_desc desc;
-	/* Current limiting */
-	unsigned int n_current_limits;
-	const int	*current_limits;
-	unsigned int limit_mask;
 	unsigned int conf;
 	unsigned int conf2;
 };
@@ -71,14 +67,14 @@ static const struct regmap_config pv88090_regmap_config = {
  *  Entry indexes corresponds to register values.
  */
 
-static const int pv88090_buck1_limits[] = {
+static const unsigned int pv88090_buck1_limits[] = {
 	 220000,  440000,  660000,  880000, 1100000, 1320000, 1540000, 1760000,
 	1980000, 2200000, 2420000, 2640000, 2860000, 3080000, 3300000, 3520000,
 	3740000, 3960000, 4180000, 4400000, 4620000, 4840000, 5060000, 5280000,
 	5500000, 5720000, 5940000, 6160000, 6380000, 6600000, 6820000, 7040000
 };
 
-static const int pv88090_buck23_limits[] = {
+static const unsigned int pv88090_buck23_limits[] = {
 	1496000, 2393000, 3291000, 4189000
 };
 
@@ -150,40 +146,6 @@ static int pv88090_buck_set_mode(struct regulator_dev *rdev,
 					PV88090_BUCK1_MODE_MASK, val);
 }
 
-static int pv88090_set_current_limit(struct regulator_dev *rdev, int min,
-				    int max)
-{
-	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
-	int i;
-
-	/* search for closest to maximum */
-	for (i = info->n_current_limits - 1; i >= 0; i--) {
-		if (min <= info->current_limits[i]
-			&& max >= info->current_limits[i]) {
-			return regmap_update_bits(rdev->regmap,
-				info->conf,
-				info->limit_mask,
-				i << PV88090_BUCK1_ILIM_SHIFT);
-		}
-	}
-
-	return -EINVAL;
-}
-
-static int pv88090_get_current_limit(struct regulator_dev *rdev)
-{
-	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret;
-
-	ret = regmap_read(rdev->regmap, info->conf, &data);
-	if (ret < 0)
-		return ret;
-
-	data = (data & info->limit_mask) >> PV88090_BUCK1_ILIM_SHIFT;
-	return info->current_limits[data];
-}
-
 static const struct regulator_ops pv88090_buck_ops = {
 	.get_mode = pv88090_buck_get_mode,
 	.set_mode = pv88090_buck_set_mode,
@@ -193,8 +155,8 @@ static const struct regulator_ops pv88090_buck_ops = {
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.list_voltage = regulator_list_voltage_linear,
-	.set_current_limit = pv88090_set_current_limit,
-	.get_current_limit = pv88090_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 };
 
 static const struct regulator_ops pv88090_ldo_ops = {
@@ -223,10 +185,11 @@ static const struct regulator_ops pv88090_ldo_ops = {
 		.enable_mask = PV88090_##regl_name##_EN, \
 		.vsel_reg = PV88090_REG_##regl_name##_CONF0, \
 		.vsel_mask = PV88090_V##regl_name##_MASK, \
+		.curr_table = limits_array, \
+		.n_current_limits = ARRAY_SIZE(limits_array), \
+		.csel_reg = PV88090_REG_##regl_name##_CONF1, \
+		.csel_mask = PV88090_##regl_name##_ILIM_MASK, \
 	},\
-	.current_limits = limits_array, \
-	.n_current_limits = ARRAY_SIZE(limits_array), \
-	.limit_mask = PV88090_##regl_name##_ILIM_MASK, \
 	.conf = PV88090_REG_##regl_name##_CONF1, \
 	.conf2 = PV88090_REG_##regl_name##_CONF2, \
 }
diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c
index a2fd140eff81..3f53f9134b32 100644
--- a/drivers/regulator/pwm-regulator.c
+++ b/drivers/regulator/pwm-regulator.c
@@ -40,9 +40,6 @@ struct pwm_regulator_data {
 	/* regulator descriptor */
 	struct regulator_desc desc;
 
-	/* Regulator ops */
-	struct regulator_ops ops;
-
 	int state;
 
 	/* Enable GPIO */
@@ -231,7 +228,7 @@ static int pwm_regulator_set_voltage(struct regulator_dev *rdev,
 	return 0;
 }
 
-static struct regulator_ops pwm_regulator_voltage_table_ops = {
+static const struct regulator_ops pwm_regulator_voltage_table_ops = {
 	.set_voltage_sel = pwm_regulator_set_voltage_sel,
 	.get_voltage_sel = pwm_regulator_get_voltage_sel,
 	.list_voltage    = pwm_regulator_list_voltage,
@@ -241,7 +238,7 @@ static struct regulator_ops pwm_regulator_voltage_table_ops = {
 	.is_enabled      = pwm_regulator_is_enabled,
 };
 
-static struct regulator_ops pwm_regulator_voltage_continuous_ops = {
+static const struct regulator_ops pwm_regulator_voltage_continuous_ops = {
 	.get_voltage = pwm_regulator_get_voltage,
 	.set_voltage = pwm_regulator_set_voltage,
 	.enable          = pwm_regulator_enable,
@@ -249,7 +246,7 @@ static struct regulator_ops pwm_regulator_voltage_continuous_ops = {
 	.is_enabled      = pwm_regulator_is_enabled,
 };
 
-static struct regulator_desc pwm_regulator_desc = {
+static const struct regulator_desc pwm_regulator_desc = {
 	.name		= "pwm-regulator",
 	.type		= REGULATOR_VOLTAGE,
 	.owner		= THIS_MODULE,
@@ -287,9 +284,7 @@ static int pwm_regulator_init_table(struct platform_device *pdev,
 
 	drvdata->state			= -EINVAL;
 	drvdata->duty_cycle_table	= duty_cycle_table;
-	memcpy(&drvdata->ops, &pwm_regulator_voltage_table_ops,
-	       sizeof(drvdata->ops));
-	drvdata->desc.ops = &drvdata->ops;
+	drvdata->desc.ops = &pwm_regulator_voltage_table_ops;
 	drvdata->desc.n_voltages	= length / sizeof(*duty_cycle_table);
 
 	return 0;
@@ -301,9 +296,7 @@ static int pwm_regulator_init_continuous(struct platform_device *pdev,
 	u32 dutycycle_range[2] = { 0, 100 };
 	u32 dutycycle_unit = 100;
 
-	memcpy(&drvdata->ops, &pwm_regulator_voltage_continuous_ops,
-	       sizeof(drvdata->ops));
-	drvdata->desc.ops = &drvdata->ops;
+	drvdata->desc.ops = &pwm_regulator_voltage_continuous_ops;
 	drvdata->desc.continuous_voltage_range = true;
 
 	of_property_read_u32_array(pdev->dev.of_node,
diff --git a/drivers/regulator/qcom_smd-regulator.c b/drivers/regulator/qcom_smd-regulator.c
index f5bca77d67c1..68bc23df4213 100644
--- a/drivers/regulator/qcom_smd-regulator.c
+++ b/drivers/regulator/qcom_smd-regulator.c
@@ -31,6 +31,11 @@ struct qcom_rpm_reg {
 
 	int is_enabled;
 	int uV;
+	u32 load;
+
+	unsigned int enabled_updated:1;
+	unsigned int uv_updated:1;
+	unsigned int load_updated:1;
 };
 
 struct rpm_regulator_req {
@@ -43,30 +48,59 @@ struct rpm_regulator_req {
 #define RPM_KEY_UV	0x00007675 /* "uv" */
 #define RPM_KEY_MA	0x0000616d /* "ma" */
 
-static int rpm_reg_write_active(struct qcom_rpm_reg *vreg,
-				struct rpm_regulator_req *req,
-				size_t size)
+static int rpm_reg_write_active(struct qcom_rpm_reg *vreg)
 {
-	return qcom_rpm_smd_write(vreg->rpm,
-				  QCOM_SMD_RPM_ACTIVE_STATE,
-				  vreg->type,
-				  vreg->id,
-				  req, size);
+	struct rpm_regulator_req req[3];
+	int reqlen = 0;
+	int ret;
+
+	if (vreg->enabled_updated) {
+		req[reqlen].key = cpu_to_le32(RPM_KEY_SWEN);
+		req[reqlen].nbytes = cpu_to_le32(sizeof(u32));
+		req[reqlen].value = cpu_to_le32(vreg->is_enabled);
+		reqlen++;
+	}
+
+	if (vreg->uv_updated && vreg->is_enabled) {
+		req[reqlen].key = cpu_to_le32(RPM_KEY_UV);
+		req[reqlen].nbytes = cpu_to_le32(sizeof(u32));
+		req[reqlen].value = cpu_to_le32(vreg->uV);
+		reqlen++;
+	}
+
+	if (vreg->load_updated && vreg->is_enabled) {
+		req[reqlen].key = cpu_to_le32(RPM_KEY_MA);
+		req[reqlen].nbytes = cpu_to_le32(sizeof(u32));
+		req[reqlen].value = cpu_to_le32(vreg->load / 1000);
+		reqlen++;
+	}
+
+	if (!reqlen)
+		return 0;
+
+	ret = qcom_rpm_smd_write(vreg->rpm, QCOM_SMD_RPM_ACTIVE_STATE,
+				 vreg->type, vreg->id,
+				 req, sizeof(req[0]) * reqlen);
+	if (!ret) {
+		vreg->enabled_updated = 0;
+		vreg->uv_updated = 0;
+		vreg->load_updated = 0;
+	}
+
+	return ret;
 }
 
 static int rpm_reg_enable(struct regulator_dev *rdev)
 {
 	struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
-	struct rpm_regulator_req req;
 	int ret;
 
-	req.key = cpu_to_le32(RPM_KEY_SWEN);
-	req.nbytes = cpu_to_le32(sizeof(u32));
-	req.value = cpu_to_le32(1);
+	vreg->is_enabled = 1;
+	vreg->enabled_updated = 1;
 
-	ret = rpm_reg_write_active(vreg, &req, sizeof(req));
-	if (!ret)
-		vreg->is_enabled = 1;
+	ret = rpm_reg_write_active(vreg);
+	if (ret)
+		vreg->is_enabled = 0;
 
 	return ret;
 }
@@ -81,16 +115,14 @@ static int rpm_reg_is_enabled(struct regulator_dev *rdev)
 static int rpm_reg_disable(struct regulator_dev *rdev)
 {
 	struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
-	struct rpm_regulator_req req;
 	int ret;
 
-	req.key = cpu_to_le32(RPM_KEY_SWEN);
-	req.nbytes = cpu_to_le32(sizeof(u32));
-	req.value = 0;
+	vreg->is_enabled = 0;
+	vreg->enabled_updated = 1;
 
-	ret = rpm_reg_write_active(vreg, &req, sizeof(req));
-	if (!ret)
-		vreg->is_enabled = 0;
+	ret = rpm_reg_write_active(vreg);
+	if (ret)
+		vreg->is_enabled = 1;
 
 	return ret;
 }
@@ -108,16 +140,15 @@ static int rpm_reg_set_voltage(struct regulator_dev *rdev,
 			       unsigned *selector)
 {
 	struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
-	struct rpm_regulator_req req;
-	int ret = 0;
+	int ret;
+	int old_uV = vreg->uV;
 
-	req.key = cpu_to_le32(RPM_KEY_UV);
-	req.nbytes = cpu_to_le32(sizeof(u32));
-	req.value = cpu_to_le32(min_uV);
+	vreg->uV = min_uV;
+	vreg->uv_updated = 1;
 
-	ret = rpm_reg_write_active(vreg, &req, sizeof(req));
-	if (!ret)
-		vreg->uV = min_uV;
+	ret = rpm_reg_write_active(vreg);
+	if (ret)
+		vreg->uV = old_uV;
 
 	return ret;
 }
@@ -125,13 +156,16 @@ static int rpm_reg_set_voltage(struct regulator_dev *rdev,
 static int rpm_reg_set_load(struct regulator_dev *rdev, int load_uA)
 {
 	struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev);
-	struct rpm_regulator_req req;
+	u32 old_load = vreg->load;
+	int ret;
 
-	req.key = cpu_to_le32(RPM_KEY_MA);
-	req.nbytes = cpu_to_le32(sizeof(u32));
-	req.value = cpu_to_le32(load_uA / 1000);
+	vreg->load = load_uA;
+	vreg->load_updated = 1;
+	ret = rpm_reg_write_active(vreg);
+	if (ret)
+		vreg->load = old_load;
 
-	return rpm_reg_write_active(vreg, &req, sizeof(req));
+	return ret;
 }
 
 static const struct regulator_ops rpm_smps_ldo_ops = {
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index 213b68743cc8..23713e16c286 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -1,5 +1,5 @@
 /*
- * Regulator driver for Rockchip RK808/RK818
+ * Regulator driver for Rockchip RK805/RK808/RK818
  *
  * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
  *
@@ -363,28 +363,28 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 				  rdev->desc->enable_mask);
 }
 
-static struct regulator_ops rk805_reg_ops = {
-		.list_voltage           = regulator_list_voltage_linear,
-		.map_voltage            = regulator_map_voltage_linear,
-		.get_voltage_sel        = regulator_get_voltage_sel_regmap,
-		.set_voltage_sel        = regulator_set_voltage_sel_regmap,
-		.enable                 = regulator_enable_regmap,
-		.disable                = regulator_disable_regmap,
-		.is_enabled             = regulator_is_enabled_regmap,
-		.set_suspend_voltage    = rk808_set_suspend_voltage,
-		.set_suspend_enable     = rk805_set_suspend_enable,
-		.set_suspend_disable    = rk805_set_suspend_disable,
+static const struct regulator_ops rk805_reg_ops = {
+	.list_voltage           = regulator_list_voltage_linear,
+	.map_voltage            = regulator_map_voltage_linear,
+	.get_voltage_sel        = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel        = regulator_set_voltage_sel_regmap,
+	.enable                 = regulator_enable_regmap,
+	.disable                = regulator_disable_regmap,
+	.is_enabled             = regulator_is_enabled_regmap,
+	.set_suspend_voltage    = rk808_set_suspend_voltage,
+	.set_suspend_enable     = rk805_set_suspend_enable,
+	.set_suspend_disable    = rk805_set_suspend_disable,
 };
 
-static struct regulator_ops rk805_switch_ops = {
-		.enable                 = regulator_enable_regmap,
-		.disable                = regulator_disable_regmap,
-		.is_enabled             = regulator_is_enabled_regmap,
-		.set_suspend_enable     = rk805_set_suspend_enable,
-		.set_suspend_disable    = rk805_set_suspend_disable,
+static const struct regulator_ops rk805_switch_ops = {
+	.enable                 = regulator_enable_regmap,
+	.disable                = regulator_disable_regmap,
+	.is_enabled             = regulator_is_enabled_regmap,
+	.set_suspend_enable     = rk805_set_suspend_enable,
+	.set_suspend_disable    = rk805_set_suspend_disable,
 };
 
-static struct regulator_ops rk808_buck1_2_ops = {
+static const struct regulator_ops rk808_buck1_2_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
 	.get_voltage_sel	= rk808_buck1_2_get_voltage_sel_regmap,
@@ -399,7 +399,7 @@ static struct regulator_ops rk808_buck1_2_ops = {
 	.set_suspend_disable	= rk808_set_suspend_disable,
 };
 
-static struct regulator_ops rk808_reg_ops = {
+static const struct regulator_ops rk808_reg_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
@@ -412,7 +412,7 @@ static struct regulator_ops rk808_reg_ops = {
 	.set_suspend_disable	= rk808_set_suspend_disable,
 };
 
-static struct regulator_ops rk808_reg_ops_ranges = {
+static const struct regulator_ops rk808_reg_ops_ranges = {
 	.list_voltage		= regulator_list_voltage_linear_range,
 	.map_voltage		= regulator_map_voltage_linear_range,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
@@ -425,7 +425,7 @@ static struct regulator_ops rk808_reg_ops_ranges = {
 	.set_suspend_disable	= rk808_set_suspend_disable,
 };
 
-static struct regulator_ops rk808_switch_ops = {
+static const struct regulator_ops rk808_switch_ops = {
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
 	.is_enabled		= regulator_is_enabled_regmap,
@@ -433,6 +433,12 @@ static struct regulator_ops rk808_switch_ops = {
 	.set_suspend_disable	= rk808_set_suspend_disable,
 };
 
+static const struct regulator_linear_range rk805_buck_1_2_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(712500, 0, 59, 12500),
+	REGULATOR_LINEAR_RANGE(1800000, 60, 62, 200000),
+	REGULATOR_LINEAR_RANGE(2300000, 63, 63, 0),
+};
+
 static const struct regulator_desc rk805_reg[] = {
 	{
 		.name = "DCDC_REG1",
@@ -440,11 +446,11 @@ static const struct regulator_desc rk805_reg[] = {
 		.of_match = of_match_ptr("DCDC_REG1"),
 		.regulators_node = of_match_ptr("regulators"),
 		.id = RK805_ID_DCDC1,
-		.ops = &rk805_reg_ops,
+		.ops = &rk808_reg_ops_ranges,
 		.type = REGULATOR_VOLTAGE,
-		.min_uV = 712500,
-		.uV_step = 12500,
 		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
 		.vsel_reg = RK805_BUCK1_ON_VSEL_REG,
 		.vsel_mask = RK818_BUCK_VSEL_MASK,
 		.enable_reg = RK805_DCDC_EN_REG,
@@ -456,11 +462,11 @@ static const struct regulator_desc rk805_reg[] = {
 		.of_match = of_match_ptr("DCDC_REG2"),
 		.regulators_node = of_match_ptr("regulators"),
 		.id = RK805_ID_DCDC2,
-		.ops = &rk805_reg_ops,
+		.ops = &rk808_reg_ops_ranges,
 		.type = REGULATOR_VOLTAGE,
-		.min_uV = 712500,
-		.uV_step = 12500,
 		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
 		.vsel_reg = RK805_BUCK2_ON_VSEL_REG,
 		.vsel_mask = RK818_BUCK_VSEL_MASK,
 		.enable_reg = RK805_DCDC_EN_REG,
@@ -796,7 +802,7 @@ static struct platform_driver rk808_regulator_driver = {
 
 module_platform_driver(rk808_regulator_driver);
 
-MODULE_DESCRIPTION("regulator driver for the RK808/RK818 series PMICs");
+MODULE_DESCRIPTION("regulator driver for the RK805/RK808/RK818 series PMICs");
 MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
 MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
 MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
diff --git a/drivers/regulator/rt5033-regulator.c b/drivers/regulator/rt5033-regulator.c
index 96d2c18e051a..639cbadc044a 100644
--- a/drivers/regulator/rt5033-regulator.c
+++ b/drivers/regulator/rt5033-regulator.c
@@ -16,14 +16,14 @@
 #include <linux/mfd/rt5033-private.h>
 #include <linux/regulator/of_regulator.h>
 
-static struct regulator_ops rt5033_safe_ldo_ops = {
+static const struct regulator_ops rt5033_safe_ldo_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
 	.list_voltage		= regulator_list_voltage_linear,
 };
 
-static struct regulator_ops rt5033_buck_ops = {
+static const struct regulator_ops rt5033_buck_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
diff --git a/drivers/regulator/s5m8767.c b/drivers/regulator/s5m8767.c
index b581f01f3395..bb9d1a083299 100644
--- a/drivers/regulator/s5m8767.c
+++ b/drivers/regulator/s5m8767.c
@@ -115,7 +115,7 @@ static const struct sec_voltage_desc *reg_voltage_map[] = {
 	[S5M8767_BUCK9] = &buck_voltage_val3,
 };
 
-static unsigned int s5m8767_opmode_reg[][4] = {
+static const unsigned int s5m8767_opmode_reg[][4] = {
 	/* {OFF, ON, LOWPOWER, SUSPEND} */
 	/* LDO1 ... LDO28 */
 	{0x0, 0x3, 0x2, 0x1}, /* LDO1 */
@@ -339,13 +339,9 @@ static int s5m8767_set_voltage_time_sel(struct regulator_dev *rdev,
 					     unsigned int new_sel)
 {
 	struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
-	const struct sec_voltage_desc *desc;
-	int reg_id = rdev_get_id(rdev);
-
-	desc = reg_voltage_map[reg_id];
 
 	if ((old_sel < new_sel) && s5m8767->ramp_delay)
-		return DIV_ROUND_UP(desc->step * (new_sel - old_sel),
+		return DIV_ROUND_UP(rdev->desc->uV_step * (new_sel - old_sel),
 					s5m8767->ramp_delay * 1000);
 	return 0;
 }
diff --git a/drivers/regulator/stm32-vrefbuf.c b/drivers/regulator/stm32-vrefbuf.c
index e0a9c445ed67..ba2f24949dc9 100644
--- a/drivers/regulator/stm32-vrefbuf.c
+++ b/drivers/regulator/stm32-vrefbuf.c
@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/of_regulator.h>
+#include <linux/pm_runtime.h>
 
 /* STM32 VREFBUF registers */
 #define STM32_VREFBUF_CSR		0x00
@@ -25,9 +26,12 @@
 #define STM32_HIZ			BIT(1)
 #define STM32_ENVR			BIT(0)
 
+#define STM32_VREFBUF_AUTO_SUSPEND_DELAY_MS	10
+
 struct stm32_vrefbuf {
 	void __iomem *base;
 	struct clk *clk;
+	struct device *dev;
 };
 
 static const unsigned int stm32_vrefbuf_voltages[] = {
@@ -38,9 +42,16 @@ static const unsigned int stm32_vrefbuf_voltages[] = {
 static int stm32_vrefbuf_enable(struct regulator_dev *rdev)
 {
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
-	u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
+	u32 val;
 	int ret;
 
+	ret = pm_runtime_get_sync(priv->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(priv->dev);
+		return ret;
+	}
+
+	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val = (val & ~STM32_HIZ) | STM32_ENVR;
 	writel_relaxed(val, priv->base + STM32_VREFBUF_CSR);
 
@@ -59,45 +70,95 @@ static int stm32_vrefbuf_enable(struct regulator_dev *rdev)
 		writel_relaxed(val, priv->base + STM32_VREFBUF_CSR);
 	}
 
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
 	return ret;
 }
 
 static int stm32_vrefbuf_disable(struct regulator_dev *rdev)
 {
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
-	u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
+	u32 val;
+	int ret;
 
+	ret = pm_runtime_get_sync(priv->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(priv->dev);
+		return ret;
+	}
+
+	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val = (val & ~STM32_ENVR) | STM32_HIZ;
 	writel_relaxed(val, priv->base + STM32_VREFBUF_CSR);
 
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
 	return 0;
 }
 
 static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev)
 {
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
+	int ret;
+
+	ret = pm_runtime_get_sync(priv->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(priv->dev);
+		return ret;
+	}
+
+	ret = readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR;
 
-	return readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR;
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
+	return ret;
 }
 
 static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev,
 					 unsigned sel)
 {
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
-	u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
+	u32 val;
+	int ret;
 
+	ret = pm_runtime_get_sync(priv->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(priv->dev);
+		return ret;
+	}
+
+	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel);
 	writel_relaxed(val, priv->base + STM32_VREFBUF_CSR);
 
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
 	return 0;
 }
 
 static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev)
 {
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
-	u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
+	u32 val;
+	int ret;
 
-	return FIELD_GET(STM32_VRS, val);
+	ret = pm_runtime_get_sync(priv->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(priv->dev);
+		return ret;
+	}
+
+	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
+	ret = FIELD_GET(STM32_VRS, val);
+
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
+	return ret;
 }
 
 static const struct regulator_ops stm32_vrefbuf_volt_ops = {
@@ -130,6 +191,7 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev)
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
+	priv->dev = &pdev->dev;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	priv->base = devm_ioremap_resource(&pdev->dev, res);
@@ -140,10 +202,17 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->clk))
 		return PTR_ERR(priv->clk);
 
+	pm_runtime_get_noresume(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev,
+					 STM32_VREFBUF_AUTO_SUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	ret = clk_prepare_enable(priv->clk);
 	if (ret) {
 		dev_err(&pdev->dev, "clk prepare failed with error %d\n", ret);
-		return ret;
+		goto err_pm_stop;
 	}
 
 	config.dev = &pdev->dev;
@@ -161,10 +230,17 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev)
 	}
 	platform_set_drvdata(pdev, rdev);
 
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_put_autosuspend(&pdev->dev);
+
 	return 0;
 
 err_clk_dis:
 	clk_disable_unprepare(priv->clk);
+err_pm_stop:
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
 
 	return ret;
 }
@@ -174,12 +250,42 @@ static int stm32_vrefbuf_remove(struct platform_device *pdev)
 	struct regulator_dev *rdev = platform_get_drvdata(pdev);
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
 
+	pm_runtime_get_sync(&pdev->dev);
 	regulator_unregister(rdev);
 	clk_disable_unprepare(priv->clk);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
 
 	return 0;
 };
 
+static int __maybe_unused stm32_vrefbuf_runtime_suspend(struct device *dev)
+{
+	struct regulator_dev *rdev = dev_get_drvdata(dev);
+	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
+
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static int __maybe_unused stm32_vrefbuf_runtime_resume(struct device *dev)
+{
+	struct regulator_dev *rdev = dev_get_drvdata(dev);
+	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
+
+	return clk_prepare_enable(priv->clk);
+}
+
+static const struct dev_pm_ops stm32_vrefbuf_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(stm32_vrefbuf_runtime_suspend,
+			   stm32_vrefbuf_runtime_resume,
+			   NULL)
+};
+
 static const struct of_device_id stm32_vrefbuf_of_match[] = {
 	{ .compatible = "st,stm32-vrefbuf", },
 	{},
@@ -192,6 +298,7 @@ static struct platform_driver stm32_vrefbuf_driver = {
 	.driver = {
 		.name  = "stm32-vrefbuf",
 		.of_match_table = of_match_ptr(stm32_vrefbuf_of_match),
+		.pm = &stm32_vrefbuf_pm_ops,
 	},
 };
 module_platform_driver(stm32_vrefbuf_driver);
diff --git a/drivers/regulator/stpmic1_regulator.c b/drivers/regulator/stpmic1_regulator.c
index a1f88e996cae..f09061473613 100644
--- a/drivers/regulator/stpmic1_regulator.c
+++ b/drivers/regulator/stpmic1_regulator.c
@@ -12,8 +12,10 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 
+#include <dt-bindings/mfd/st,stpmic1.h>
+
 /**
- * stpmic1 regulator description
+ * stpmic1 regulator description: this structure is used as driver data
  * @desc: regulator framework description
  * @mask_reset_reg: mask reset register address
  * @mask_reset_mask: mask rank and mask reset register mask
@@ -28,28 +30,9 @@ struct stpmic1_regulator_cfg {
 	u8 icc_mask;
 };
 
-/**
- * stpmic1 regulator data: this structure is used as driver data
- * @regul_id: regulator id
- * @reg_node: DT node of regulator (unused on non-DT platforms)
- * @cfg: stpmic specific regulator description
- * @mask_reset: mask_reset bit value
- * @irq_curlim: current limit interrupt number
- * @regmap: point to parent regmap structure
- */
-struct stpmic1_regulator {
-	unsigned int regul_id;
-	struct device_node *reg_node;
-	struct stpmic1_regulator_cfg *cfg;
-	u8 mask_reset;
-	int irq_curlim;
-	struct regmap *regmap;
-};
-
 static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode);
 static unsigned int stpmic1_get_mode(struct regulator_dev *rdev);
 static int stpmic1_set_icc(struct regulator_dev *rdev);
-static int stpmic1_regulator_parse_dt(void *driver_data);
 static unsigned int stpmic1_map_mode(unsigned int mode);
 
 enum {
@@ -72,16 +55,13 @@ enum {
 /* Enable time worst case is 5000mV/(2250uV/uS) */
 #define PMIC_ENABLE_TIME_US 2200
 
-#define STPMIC1_BUCK_MODE_NORMAL 0
-#define STPMIC1_BUCK_MODE_LP BUCK_HPLP_ENABLE_MASK
-
 static const struct regulator_linear_range buck1_ranges[] = {
 	REGULATOR_LINEAR_RANGE(725000, 0, 4, 0),
 	REGULATOR_LINEAR_RANGE(725000, 5, 36, 25000),
 	REGULATOR_LINEAR_RANGE(1500000, 37, 63, 0),
 };
 
-struct regulator_linear_range buck2_ranges[] = {
+static const struct regulator_linear_range buck2_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1000000, 0, 17, 0),
 	REGULATOR_LINEAR_RANGE(1050000, 18, 19, 0),
 	REGULATOR_LINEAR_RANGE(1100000, 20, 21, 0),
@@ -95,7 +75,7 @@ struct regulator_linear_range buck2_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1500000, 36, 63, 0),
 };
 
-struct regulator_linear_range buck3_ranges[] = {
+static const struct regulator_linear_range buck3_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1000000, 0, 19, 0),
 	REGULATOR_LINEAR_RANGE(1100000, 20, 23, 0),
 	REGULATOR_LINEAR_RANGE(1200000, 24, 27, 0),
@@ -103,10 +83,9 @@ struct regulator_linear_range buck3_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1400000, 32, 35, 0),
 	REGULATOR_LINEAR_RANGE(1500000, 36, 55, 100000),
 	REGULATOR_LINEAR_RANGE(3400000, 56, 63, 0),
-
 };
 
-struct regulator_linear_range buck4_ranges[] = {
+static const struct regulator_linear_range buck4_ranges[] = {
 	REGULATOR_LINEAR_RANGE(600000, 0, 27, 25000),
 	REGULATOR_LINEAR_RANGE(1300000, 28, 29, 0),
 	REGULATOR_LINEAR_RANGE(1350000, 30, 31, 0),
@@ -114,24 +93,21 @@ struct regulator_linear_range buck4_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1450000, 34, 35, 0),
 	REGULATOR_LINEAR_RANGE(1500000, 36, 60, 100000),
 	REGULATOR_LINEAR_RANGE(3900000, 61, 63, 0),
-
 };
 
-struct regulator_linear_range ldo1_ranges[] = {
+static const struct regulator_linear_range ldo1_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
 	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
 	REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0),
-
 };
 
-struct regulator_linear_range ldo2_ranges[] = {
+static const struct regulator_linear_range ldo2_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
 	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
 	REGULATOR_LINEAR_RANGE(3300000, 25, 30, 0),
-
 };
 
-struct regulator_linear_range ldo3_ranges[] = {
+static const struct regulator_linear_range ldo3_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
 	REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000),
 	REGULATOR_LINEAR_RANGE(3300000, 25, 30, 0),
@@ -139,18 +115,18 @@ struct regulator_linear_range ldo3_ranges[] = {
 	REGULATOR_LINEAR_RANGE(500000, 31, 31, 0),
 };
 
-struct regulator_linear_range ldo5_ranges[] = {
+static const struct regulator_linear_range ldo5_ranges[] = {
 	REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0),
 	REGULATOR_LINEAR_RANGE(1700000, 8, 30, 100000),
 	REGULATOR_LINEAR_RANGE(3900000, 31, 31, 0),
 };
 
-struct regulator_linear_range ldo6_ranges[] = {
+static const struct regulator_linear_range ldo6_ranges[] = {
 	REGULATOR_LINEAR_RANGE(900000, 0, 24, 100000),
 	REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0),
 };
 
-static struct regulator_ops stpmic1_ldo_ops = {
+static const struct regulator_ops stpmic1_ldo_ops = {
 	.list_voltage = regulator_list_voltage_linear_range,
 	.map_voltage = regulator_map_voltage_linear_range,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -158,11 +134,10 @@ static struct regulator_ops stpmic1_ldo_ops = {
 	.disable = regulator_disable_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
-	.set_pull_down = regulator_set_pull_down_regmap,
 	.set_over_current_protection = stpmic1_set_icc,
 };
 
-static struct regulator_ops stpmic1_ldo3_ops = {
+static const struct regulator_ops stpmic1_ldo3_ops = {
 	.list_voltage = regulator_list_voltage_linear_range,
 	.map_voltage = regulator_map_voltage_iterate,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -170,21 +145,19 @@ static struct regulator_ops stpmic1_ldo3_ops = {
 	.disable = regulator_disable_regmap,
 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
-	.set_pull_down = regulator_set_pull_down_regmap,
 	.get_bypass = regulator_get_bypass_regmap,
 	.set_bypass = regulator_set_bypass_regmap,
 	.set_over_current_protection = stpmic1_set_icc,
 };
 
-static struct regulator_ops stpmic1_ldo4_fixed_regul_ops = {
+static const struct regulator_ops stpmic1_ldo4_fixed_regul_ops = {
 	.is_enabled = regulator_is_enabled_regmap,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
-	.set_pull_down = regulator_set_pull_down_regmap,
 	.set_over_current_protection = stpmic1_set_icc,
 };
 
-static struct regulator_ops stpmic1_buck_ops = {
+static const struct regulator_ops stpmic1_buck_ops = {
 	.list_voltage = regulator_list_voltage_linear_range,
 	.map_voltage = regulator_map_voltage_linear_range,
 	.is_enabled = regulator_is_enabled_regmap,
@@ -198,20 +171,27 @@ static struct regulator_ops stpmic1_buck_ops = {
 	.set_over_current_protection = stpmic1_set_icc,
 };
 
-static struct regulator_ops stpmic1_vref_ddr_ops = {
+static const struct regulator_ops stpmic1_vref_ddr_ops = {
 	.is_enabled = regulator_is_enabled_regmap,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
-	.set_pull_down = regulator_set_pull_down_regmap,
 };
 
-static struct regulator_ops stpmic1_switch_regul_ops = {
+static const struct regulator_ops stpmic1_boost_regul_ops = {
 	.is_enabled = regulator_is_enabled_regmap,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.set_over_current_protection = stpmic1_set_icc,
 };
 
+static const struct regulator_ops stpmic1_switch_regul_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.set_over_current_protection = stpmic1_set_icc,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
 #define REG_LDO(ids, base) { \
 	.name = #ids, \
 	.id = STPMIC1_##ids, \
@@ -228,8 +208,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = {
 	.enable_val = 1, \
 	.disable_val = 0, \
 	.enable_time = PMIC_ENABLE_TIME_US, \
-	.pull_down_reg = ids##_PULL_DOWN_REG, \
-	.pull_down_mask = ids##_PULL_DOWN_MASK, \
 	.supply_name = #base, \
 }
 
@@ -253,8 +231,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = {
 	.bypass_mask = LDO_BYPASS_MASK, \
 	.bypass_val_on = LDO_BYPASS_MASK, \
 	.bypass_val_off = 0, \
-	.pull_down_reg = ids##_PULL_DOWN_REG, \
-	.pull_down_mask = ids##_PULL_DOWN_MASK, \
 	.supply_name = #base, \
 }
 
@@ -272,8 +248,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = {
 	.enable_val = 1, \
 	.disable_val = 0, \
 	.enable_time = PMIC_ENABLE_TIME_US, \
-	.pull_down_reg = ids##_PULL_DOWN_REG, \
-	.pull_down_mask = ids##_PULL_DOWN_MASK, \
 	.supply_name = #base, \
 }
 
@@ -313,12 +287,47 @@ static struct regulator_ops stpmic1_switch_regul_ops = {
 	.enable_val = 1, \
 	.disable_val = 0, \
 	.enable_time = PMIC_ENABLE_TIME_US, \
-	.pull_down_reg = ids##_PULL_DOWN_REG, \
-	.pull_down_mask = ids##_PULL_DOWN_MASK, \
 	.supply_name = #base, \
 }
 
-#define REG_SWITCH(ids, base, reg, mask, val) { \
+#define REG_BOOST(ids, base) { \
+	.name = #ids, \
+	.id = STPMIC1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmic1_boost_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = BOOST_ENABLED, \
+	.enable_val = BOOST_ENABLED, \
+	.disable_val = 0, \
+	.enable_time = PMIC_ENABLE_TIME_US, \
+	.supply_name = #base, \
+}
+
+#define REG_VBUS_OTG(ids, base) { \
+	.name = #ids, \
+	.id = STPMIC1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmic1_switch_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = USBSW_OTG_SWITCH_ENABLED, \
+	.enable_val = USBSW_OTG_SWITCH_ENABLED, \
+	.disable_val = 0, \
+	.enable_time = PMIC_ENABLE_TIME_US, \
+	.supply_name = #base, \
+	.active_discharge_reg = BST_SW_CR, \
+	.active_discharge_mask = VBUS_OTG_DISCHARGE, \
+	.active_discharge_on = VBUS_OTG_DISCHARGE, \
+}
+
+#define REG_SW_OUT(ids, base) { \
 	.name = #ids, \
 	.id = STPMIC1_##ids, \
 	.n_voltages = 1, \
@@ -327,15 +336,18 @@ static struct regulator_ops stpmic1_switch_regul_ops = {
 	.owner = THIS_MODULE, \
 	.min_uV = 0, \
 	.fixed_uV = 5000000, \
-	.enable_reg = (reg), \
-	.enable_mask = (mask), \
-	.enable_val = (val), \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = SWIN_SWOUT_ENABLED, \
+	.enable_val = SWIN_SWOUT_ENABLED, \
 	.disable_val = 0, \
 	.enable_time = PMIC_ENABLE_TIME_US, \
 	.supply_name = #base, \
+	.active_discharge_reg = BST_SW_CR, \
+	.active_discharge_mask = SW_OUT_DISCHARGE, \
+	.active_discharge_on = SW_OUT_DISCHARGE, \
 }
 
-struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
+static const struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
 	[STPMIC1_BUCK1] = {
 		.desc = REG_BUCK(BUCK1, buck1),
 		.icc_reg = BUCKS_ICCTO_CR,
@@ -412,23 +424,17 @@ struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
 		.mask_reset_mask = BIT(6),
 	},
 	[STPMIC1_BOOST] = {
-		.desc = REG_SWITCH(BOOST, boost, BST_SW_CR,
-				   BOOST_ENABLED,
-				   BOOST_ENABLED),
+		.desc = REG_BOOST(BOOST, boost),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(6),
 	},
 	[STPMIC1_VBUS_OTG] = {
-		.desc = REG_SWITCH(VBUS_OTG, pwr_sw1, BST_SW_CR,
-				   USBSW_OTG_SWITCH_ENABLED,
-				   USBSW_OTG_SWITCH_ENABLED),
+		.desc = REG_VBUS_OTG(VBUS_OTG, pwr_sw1),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(4),
 	},
 	[STPMIC1_SW_OUT] = {
-		.desc = REG_SWITCH(SW_OUT, pwr_sw2, BST_SW_CR,
-				   SWIN_SWOUT_ENABLED,
-				   SWIN_SWOUT_ENABLED),
+		.desc = REG_SW_OUT(SW_OUT, pwr_sw2),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(5),
 	},
@@ -449,8 +455,9 @@ static unsigned int stpmic1_map_mode(unsigned int mode)
 static unsigned int stpmic1_get_mode(struct regulator_dev *rdev)
 {
 	int value;
+	struct regmap *regmap = rdev_get_regmap(rdev);
 
-	regmap_read(rdev->regmap, rdev->desc->enable_reg, &value);
+	regmap_read(regmap, rdev->desc->enable_reg, &value);
 
 	if (value & STPMIC1_BUCK_MODE_LP)
 		return REGULATOR_MODE_STANDBY;
@@ -461,6 +468,7 @@ static unsigned int stpmic1_get_mode(struct regulator_dev *rdev)
 static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode)
 {
 	int value;
+	struct regmap *regmap = rdev_get_regmap(rdev);
 
 	switch (mode) {
 	case REGULATOR_MODE_NORMAL:
@@ -473,17 +481,18 @@ static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode)
 		return -EINVAL;
 	}
 
-	return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+	return regmap_update_bits(regmap, rdev->desc->enable_reg,
 				  STPMIC1_BUCK_MODE_LP, value);
 }
 
 static int stpmic1_set_icc(struct regulator_dev *rdev)
 {
-	struct stpmic1_regulator *regul = rdev_get_drvdata(rdev);
+	struct stpmic1_regulator_cfg *cfg = rdev_get_drvdata(rdev);
+	struct regmap *regmap = rdev_get_regmap(rdev);
 
 	/* enable switch off in case of over current */
-	return regmap_update_bits(regul->regmap, regul->cfg->icc_reg,
-				  regul->cfg->icc_mask, regul->cfg->icc_mask);
+	return regmap_update_bits(regmap, cfg->icc_reg, cfg->icc_mask,
+				  cfg->icc_mask);
 }
 
 static irqreturn_t stpmic1_curlim_irq_handler(int irq, void *data)
@@ -502,46 +511,13 @@ static irqreturn_t stpmic1_curlim_irq_handler(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static int stpmic1_regulator_init(struct platform_device *pdev,
-				  struct regulator_dev *rdev)
-{
-	struct stpmic1_regulator *regul = rdev_get_drvdata(rdev);
-	int ret = 0;
-
-	/* set mask reset */
-	if (regul->mask_reset && regul->cfg->mask_reset_reg != 0) {
-		ret = regmap_update_bits(regul->regmap,
-					 regul->cfg->mask_reset_reg,
-					 regul->cfg->mask_reset_mask,
-					 regul->cfg->mask_reset_mask);
-		if (ret) {
-			dev_err(&pdev->dev, "set mask reset failed\n");
-			return ret;
-		}
-	}
-
-	/* setup an irq handler for over-current detection */
-	if (regul->irq_curlim > 0) {
-		ret = devm_request_threaded_irq(&pdev->dev,
-						regul->irq_curlim, NULL,
-						stpmic1_curlim_irq_handler,
-						IRQF_ONESHOT | IRQF_SHARED,
-						pdev->name, rdev);
-		if (ret) {
-			dev_err(&pdev->dev, "Request IRQ failed\n");
-			return ret;
-		}
-	}
-	return 0;
-}
-
 #define MATCH(_name, _id) \
 	[STPMIC1_##_id] = { \
 		.name = #_name, \
 		.desc = &stpmic1_regulator_cfgs[STPMIC1_##_id].desc, \
 	}
 
-static struct of_regulator_match stpmic1_regulators_matches[] = {
+static struct of_regulator_match stpmic1_matches[] = {
 	MATCH(buck1, BUCK1),
 	MATCH(buck2, BUCK2),
 	MATCH(buck3, BUCK3),
@@ -558,94 +534,75 @@ static struct of_regulator_match stpmic1_regulators_matches[] = {
 	MATCH(pwr_sw2, SW_OUT),
 };
 
-static int stpmic1_regulator_parse_dt(void *driver_data)
-{
-	struct stpmic1_regulator *regul =
-		(struct stpmic1_regulator *)driver_data;
-
-	if (!regul)
-		return -EINVAL;
-
-	if (of_get_property(regul->reg_node, "st,mask-reset", NULL))
-		regul->mask_reset = 1;
-
-	regul->irq_curlim = of_irq_get(regul->reg_node, 0);
-
-	return 0;
-}
-
-static struct
-regulator_dev *stpmic1_regulator_register(struct platform_device *pdev, int id,
-					  struct regulator_init_data *init_data,
-					  struct stpmic1_regulator *regul)
+static int stpmic1_regulator_register(struct platform_device *pdev, int id,
+				      struct of_regulator_match *match,
+				      const struct stpmic1_regulator_cfg *cfg)
 {
 	struct stpmic1 *pmic_dev = dev_get_drvdata(pdev->dev.parent);
 	struct regulator_dev *rdev;
 	struct regulator_config config = {};
+	int ret = 0;
+	int irq;
 
 	config.dev = &pdev->dev;
-	config.init_data = init_data;
-	config.of_node = stpmic1_regulators_matches[id].of_node;
+	config.init_data = match->init_data;
+	config.of_node = match->of_node;
 	config.regmap = pmic_dev->regmap;
-	config.driver_data = regul;
-
-	regul->regul_id = id;
-	regul->reg_node = config.of_node;
-	regul->cfg = &stpmic1_regulator_cfgs[id];
-	regul->regmap = pmic_dev->regmap;
+	config.driver_data = (void *)cfg;
 
-	rdev = devm_regulator_register(&pdev->dev, &regul->cfg->desc, &config);
+	rdev = devm_regulator_register(&pdev->dev, &cfg->desc, &config);
 	if (IS_ERR(rdev)) {
 		dev_err(&pdev->dev, "failed to register %s regulator\n",
-			regul->cfg->desc.name);
+			cfg->desc.name);
+		return PTR_ERR(rdev);
+	}
+
+	/* set mask reset */
+	if (of_get_property(config.of_node, "st,mask-reset", NULL) &&
+	    cfg->mask_reset_reg != 0) {
+		ret = regmap_update_bits(pmic_dev->regmap,
+					 cfg->mask_reset_reg,
+					 cfg->mask_reset_mask,
+					 cfg->mask_reset_mask);
+		if (ret) {
+			dev_err(&pdev->dev, "set mask reset failed\n");
+			return ret;
+		}
 	}
 
-	return rdev;
+	/* setup an irq handler for over-current detection */
+	irq = of_irq_get(config.of_node, 0);
+	if (irq > 0) {
+		ret = devm_request_threaded_irq(&pdev->dev,
+						irq, NULL,
+						stpmic1_curlim_irq_handler,
+						IRQF_ONESHOT | IRQF_SHARED,
+						pdev->name, rdev);
+		if (ret) {
+			dev_err(&pdev->dev, "Request IRQ failed\n");
+			return ret;
+		}
+	}
+	return 0;
 }
 
 static int stpmic1_regulator_probe(struct platform_device *pdev)
 {
-	struct regulator_dev *rdev;
-	struct stpmic1_regulator *regul;
-	struct regulator_init_data *init_data;
-	struct device_node *np;
 	int i, ret;
 
-	np = pdev->dev.of_node;
-
-	ret = of_regulator_match(&pdev->dev, np,
-				 stpmic1_regulators_matches,
-				 ARRAY_SIZE(stpmic1_regulators_matches));
+	ret = of_regulator_match(&pdev->dev, pdev->dev.of_node, stpmic1_matches,
+				 ARRAY_SIZE(stpmic1_matches));
 	if (ret < 0) {
 		dev_err(&pdev->dev,
 			"Error in PMIC regulator device tree node");
 		return ret;
 	}
 
-	regul = devm_kzalloc(&pdev->dev, ARRAY_SIZE(stpmic1_regulator_cfgs) *
-			     sizeof(struct stpmic1_regulator),
-			     GFP_KERNEL);
-	if (!regul)
-		return -ENOMEM;
-
 	for (i = 0; i < ARRAY_SIZE(stpmic1_regulator_cfgs); i++) {
-		/* Parse DT & find regulators to register */
-		init_data = stpmic1_regulators_matches[i].init_data;
-		if (init_data)
-			init_data->regulator_init = &stpmic1_regulator_parse_dt;
-
-		rdev = stpmic1_regulator_register(pdev, i, init_data, regul);
-		if (IS_ERR(rdev))
-			return PTR_ERR(rdev);
-
-		ret = stpmic1_regulator_init(pdev, rdev);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"failed to initialize regulator %d\n", ret);
+		ret = stpmic1_regulator_register(pdev, i, &stpmic1_matches[i],
+						 &stpmic1_regulator_cfgs[i]);
+		if (ret < 0)
 			return ret;
-		}
-
-		regul++;
 	}
 
 	dev_dbg(&pdev->dev, "stpmic1_regulator driver probed\n");
diff --git a/drivers/regulator/tps65218-regulator.c b/drivers/regulator/tps65218-regulator.c
index 5dd559eabc81..95708d34876b 100644
--- a/drivers/regulator/tps65218-regulator.c
+++ b/drivers/regulator/tps65218-regulator.c
@@ -205,7 +205,8 @@ static int tps65218_pmic_set_input_current_lim(struct regulator_dev *dev,
 		return -EINVAL;
 
 	return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask,
-				 index << 2, TPS65218_PROTECT_L1);
+				 index << __builtin_ctz(dev->desc->csel_mask),
+				 TPS65218_PROTECT_L1);
 }
 
 static int tps65218_pmic_set_current_limit(struct regulator_dev *dev,
@@ -224,7 +225,8 @@ static int tps65218_pmic_set_current_limit(struct regulator_dev *dev,
 		return -EINVAL;
 
 	return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask,
-				 index << 2, TPS65218_PROTECT_L1);
+				 index << __builtin_ctz(dev->desc->csel_mask),
+				 TPS65218_PROTECT_L1);
 }
 
 static int tps65218_pmic_get_current_limit(struct regulator_dev *dev)
@@ -237,12 +239,13 @@ static int tps65218_pmic_get_current_limit(struct regulator_dev *dev)
 	if (retval < 0)
 		return retval;
 
-	index = (index & dev->desc->csel_mask) >> 2;
+	index = (index & dev->desc->csel_mask) >>
+					 __builtin_ctz(dev->desc->csel_mask);
 
 	return ls3_currents[index];
 }
 
-static struct regulator_ops tps65218_ls3_ops = {
+static struct regulator_ops tps65218_ls23_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= tps65218_pmic_enable,
 	.disable		= tps65218_pmic_disable,
@@ -304,8 +307,13 @@ static const struct regulator_desc regulators[] = {
 			   TPS65218_ENABLE2_LDO1_EN, 0, 0, ldo1_dcdc3_ranges,
 			   2, 0, 0, TPS65218_REG_SEQ6,
 			   TPS65218_SEQ6_LDO1_SEQ_MASK),
+	TPS65218_REGULATOR("LS2", "regulator-ls2", TPS65218_LS_2,
+			   REGULATOR_CURRENT, tps65218_ls23_ops, 0, 0, 0,
+			   TPS65218_REG_ENABLE2, TPS65218_ENABLE2_LS2_EN,
+			   TPS65218_REG_CONFIG2, TPS65218_CONFIG2_LS2ILIM_MASK,
+			   NULL, 0, 0, 0, 0, 0),
 	TPS65218_REGULATOR("LS3", "regulator-ls3", TPS65218_LS_3,
-			   REGULATOR_CURRENT, tps65218_ls3_ops, 0, 0, 0,
+			   REGULATOR_CURRENT, tps65218_ls23_ops, 0, 0, 0,
 			   TPS65218_REG_ENABLE2, TPS65218_ENABLE2_LS3_EN,
 			   TPS65218_REG_CONFIG2, TPS65218_CONFIG2_LS3ILIM_MASK,
 			   NULL, 0, 0, 0, 0, 0),
diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c
index 884c7505ed91..402ea43c77d1 100644
--- a/drivers/regulator/twl-regulator.c
+++ b/drivers/regulator/twl-regulator.c
@@ -576,14 +576,9 @@ static int twlreg_probe(struct platform_device *pdev)
 	struct regulator_init_data	*initdata;
 	struct regulation_constraints	*c;
 	struct regulator_dev		*rdev;
-	const struct of_device_id	*match;
 	struct regulator_config		config = { };
 
-	match = of_match_device(twl_of_match, &pdev->dev);
-	if (!match)
-		return -ENODEV;
-
-	template = match->data;
+	template = of_device_get_match_data(&pdev->dev);
 	if (!template)
 		return -ENODEV;
 
diff --git a/drivers/regulator/twl6030-regulator.c b/drivers/regulator/twl6030-regulator.c
index 219cbd910dbf..15f19df6bc5d 100644
--- a/drivers/regulator/twl6030-regulator.c
+++ b/drivers/regulator/twl6030-regulator.c
@@ -31,9 +31,6 @@ struct twlreg_info {
 	/* twl resource ID, for resource control state machine */
 	u8			id;
 
-	/* chip constraints on regulator behavior */
-	u16			min_mV;
-
 	u8			flags;
 
 	/* used by regulator core */
@@ -247,32 +244,11 @@ static int twl6030coresmps_get_voltage(struct regulator_dev *rdev)
 	return -ENODEV;
 }
 
-static struct regulator_ops twl6030coresmps_ops = {
+static const struct regulator_ops twl6030coresmps_ops = {
 	.set_voltage	= twl6030coresmps_set_voltage,
 	.get_voltage	= twl6030coresmps_get_voltage,
 };
 
-static int twl6030ldo_list_voltage(struct regulator_dev *rdev, unsigned sel)
-{
-	struct twlreg_info *info = rdev_get_drvdata(rdev);
-
-	switch (sel) {
-	case 0:
-		return 0;
-	case 1 ... 24:
-		/* Linear mapping from 00000001 to 00011000:
-		 * Absolute voltage value = 1.0 V + 0.1 V × (sel – 00000001)
-		 */
-		return (info->min_mV + 100 * (sel - 1)) * 1000;
-	case 25 ... 30:
-		return -EINVAL;
-	case 31:
-		return 2750000;
-	default:
-		return -EINVAL;
-	}
-}
-
 static int
 twl6030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector)
 {
@@ -290,8 +266,8 @@ static int twl6030ldo_get_voltage_sel(struct regulator_dev *rdev)
 	return vsel;
 }
 
-static struct regulator_ops twl6030ldo_ops = {
-	.list_voltage	= twl6030ldo_list_voltage,
+static const struct regulator_ops twl6030ldo_ops = {
+	.list_voltage	= regulator_list_voltage_linear_range,
 
 	.set_voltage_sel = twl6030ldo_set_voltage_sel,
 	.get_voltage_sel = twl6030ldo_get_voltage_sel,
@@ -305,7 +281,7 @@ static struct regulator_ops twl6030ldo_ops = {
 	.get_status	= twl6030reg_get_status,
 };
 
-static struct regulator_ops twl6030fixed_ops = {
+static const struct regulator_ops twl6030fixed_ops = {
 	.list_voltage	= regulator_list_voltage_linear,
 
 	.enable		= twl6030reg_enable,
@@ -496,7 +472,7 @@ static int twl6030smps_get_voltage_sel(struct regulator_dev *rdev)
 	return twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS);
 }
 
-static struct regulator_ops twlsmps_ops = {
+static const struct regulator_ops twlsmps_ops = {
 	.list_voltage		= twl6030smps_list_voltage,
 	.map_voltage		= twl6030smps_map_voltage,
 
@@ -513,6 +489,11 @@ static struct regulator_ops twlsmps_ops = {
 };
 
 /*----------------------------------------------------------------------*/
+static const struct regulator_linear_range twl6030ldo_linear_range[] = {
+	REGULATOR_LINEAR_RANGE(0, 0, 0, 0),
+	REGULATOR_LINEAR_RANGE(1000000, 1, 24, 100000),
+	REGULATOR_LINEAR_RANGE(2750000, 31, 31, 0),
+};
 
 #define TWL6030_ADJUSTABLE_SMPS(label) \
 static const struct twlreg_info TWL6030_INFO_##label = { \
@@ -525,28 +506,30 @@ static const struct twlreg_info TWL6030_INFO_##label = { \
 		}, \
 	}
 
-#define TWL6030_ADJUSTABLE_LDO(label, offset, min_mVolts) \
+#define TWL6030_ADJUSTABLE_LDO(label, offset) \
 static const struct twlreg_info TWL6030_INFO_##label = { \
 	.base = offset, \
-	.min_mV = min_mVolts, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6030_REG_##label, \
 		.n_voltages = 32, \
+		.linear_ranges = twl6030ldo_linear_range, \
+		.n_linear_ranges = ARRAY_SIZE(twl6030ldo_linear_range), \
 		.ops = &twl6030ldo_ops, \
 		.type = REGULATOR_VOLTAGE, \
 		.owner = THIS_MODULE, \
 		}, \
 	}
 
-#define TWL6032_ADJUSTABLE_LDO(label, offset, min_mVolts) \
+#define TWL6032_ADJUSTABLE_LDO(label, offset) \
 static const struct twlreg_info TWL6032_INFO_##label = { \
 	.base = offset, \
-	.min_mV = min_mVolts, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6032_REG_##label, \
 		.n_voltages = 32, \
+		.linear_ranges = twl6030ldo_linear_range, \
+		.n_linear_ranges = ARRAY_SIZE(twl6030ldo_linear_range), \
 		.ops = &twl6030ldo_ops, \
 		.type = REGULATOR_VOLTAGE, \
 		.owner = THIS_MODULE, \
@@ -557,7 +540,6 @@ static const struct twlreg_info TWL6032_INFO_##label = { \
 static const struct twlreg_info TWLFIXED_INFO_##label = { \
 	.base = offset, \
 	.id = 0, \
-	.min_mV = mVolts, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6030##_REG_##label, \
@@ -574,7 +556,6 @@ static const struct twlreg_info TWLFIXED_INFO_##label = { \
 #define TWL6032_ADJUSTABLE_SMPS(label, offset) \
 static const struct twlreg_info TWLSMPS_INFO_##label = { \
 	.base = offset, \
-	.min_mV = 600, \
 	.desc = { \
 		.name = #label, \
 		.id = TWL6032_REG_##label, \
@@ -592,22 +573,22 @@ static const struct twlreg_info TWLSMPS_INFO_##label = { \
 TWL6030_ADJUSTABLE_SMPS(VDD1);
 TWL6030_ADJUSTABLE_SMPS(VDD2);
 TWL6030_ADJUSTABLE_SMPS(VDD3);
-TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54, 1000);
-TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58, 1000);
-TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c, 1000);
-TWL6030_ADJUSTABLE_LDO(VMMC, 0x68, 1000);
-TWL6030_ADJUSTABLE_LDO(VPP, 0x6c, 1000);
-TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74, 1000);
+TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54);
+TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58);
+TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c);
+TWL6030_ADJUSTABLE_LDO(VMMC, 0x68);
+TWL6030_ADJUSTABLE_LDO(VPP, 0x6c);
+TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74);
 /* 6025 are renamed compared to 6030 versions */
-TWL6032_ADJUSTABLE_LDO(LDO2, 0x54, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO4, 0x58, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO3, 0x5c, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO5, 0x68, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO1, 0x6c, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO7, 0x74, 1000);
-TWL6032_ADJUSTABLE_LDO(LDO6, 0x60, 1000);
-TWL6032_ADJUSTABLE_LDO(LDOLN, 0x64, 1000);
-TWL6032_ADJUSTABLE_LDO(LDOUSB, 0x70, 1000);
+TWL6032_ADJUSTABLE_LDO(LDO2, 0x54);
+TWL6032_ADJUSTABLE_LDO(LDO4, 0x58);
+TWL6032_ADJUSTABLE_LDO(LDO3, 0x5c);
+TWL6032_ADJUSTABLE_LDO(LDO5, 0x68);
+TWL6032_ADJUSTABLE_LDO(LDO1, 0x6c);
+TWL6032_ADJUSTABLE_LDO(LDO7, 0x74);
+TWL6032_ADJUSTABLE_LDO(LDO6, 0x60);
+TWL6032_ADJUSTABLE_LDO(LDOLN, 0x64);
+TWL6032_ADJUSTABLE_LDO(LDOUSB, 0x70);
 TWL6030_FIXED_LDO(VANA, 0x50, 2100, 0);
 TWL6030_FIXED_LDO(VCXIO, 0x60, 1800, 0);
 TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0);
@@ -687,14 +668,9 @@ static int twlreg_probe(struct platform_device *pdev)
 	struct regulator_init_data	*initdata;
 	struct regulation_constraints	*c;
 	struct regulator_dev		*rdev;
-	const struct of_device_id	*match;
 	struct regulator_config		config = { };
 
-	match = of_match_device(twl_of_match, &pdev->dev);
-	if (!match)
-		return -ENODEV;
-
-	template = match->data;
+	template = of_device_get_match_data(&pdev->dev);
 	if (!template)
 		return -ENODEV;
 
diff --git a/drivers/regulator/wm831x-dcdc.c b/drivers/regulator/wm831x-dcdc.c
index df591435d12a..12b422373580 100644
--- a/drivers/regulator/wm831x-dcdc.c
+++ b/drivers/regulator/wm831x-dcdc.c
@@ -205,33 +205,10 @@ static irqreturn_t wm831x_dcdc_oc_irq(int irq, void *data)
  * BUCKV specifics
  */
 
-static int wm831x_buckv_list_voltage(struct regulator_dev *rdev,
-				      unsigned selector)
-{
-	if (selector <= 0x8)
-		return 600000;
-	if (selector <= WM831X_BUCKV_MAX_SELECTOR)
-		return 600000 + ((selector - 0x8) * 12500);
-	return -EINVAL;
-}
-
-static int wm831x_buckv_map_voltage(struct regulator_dev *rdev,
-				   int min_uV, int max_uV)
-{
-	u16 vsel;
-
-	if (min_uV < 600000)
-		vsel = 0;
-	else if (min_uV <= 1800000)
-		vsel = DIV_ROUND_UP(min_uV - 600000, 12500) + 8;
-	else
-		return -EINVAL;
-
-	if (wm831x_buckv_list_voltage(rdev, vsel) > max_uV)
-		return -EINVAL;
-
-	return vsel;
-}
+static const struct regulator_linear_range wm831x_buckv_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0, 0x7, 0),
+	REGULATOR_LINEAR_RANGE(600000, 0x8, 0x68, 12500),
+};
 
 static int wm831x_buckv_set_dvs(struct regulator_dev *rdev, int state)
 {
@@ -309,7 +286,7 @@ static int wm831x_buckv_set_suspend_voltage(struct regulator_dev *rdev,
 	u16 reg = dcdc->base + WM831X_DCDC_SLEEP_CONTROL;
 	int vsel;
 
-	vsel = wm831x_buckv_map_voltage(rdev, uV, uV);
+	vsel = regulator_map_voltage_linear_range(rdev, uV, uV);
 	if (vsel < 0)
 		return vsel;
 
@@ -331,48 +308,14 @@ static const unsigned int wm831x_dcdc_ilim[] = {
 	125000, 250000, 375000, 500000, 625000, 750000, 875000, 1000000
 };
 
-static int wm831x_buckv_set_current_limit(struct regulator_dev *rdev,
-					   int min_uA, int max_uA)
-{
-	struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev);
-	struct wm831x *wm831x = dcdc->wm831x;
-	u16 reg = dcdc->base + WM831X_DCDC_CONTROL_2;
-	int i;
-
-	for (i = ARRAY_SIZE(wm831x_dcdc_ilim) - 1; i >= 0; i--) {
-		if ((min_uA <= wm831x_dcdc_ilim[i]) &&
-		    (wm831x_dcdc_ilim[i] <= max_uA))
-			return wm831x_set_bits(wm831x, reg,
-					       WM831X_DC1_HC_THR_MASK,
-						i << WM831X_DC1_HC_THR_SHIFT);
-	}
-
-	return -EINVAL;
-}
-
-static int wm831x_buckv_get_current_limit(struct regulator_dev *rdev)
-{
-	struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev);
-	struct wm831x *wm831x = dcdc->wm831x;
-	u16 reg = dcdc->base + WM831X_DCDC_CONTROL_2;
-	int val;
-
-	val = wm831x_reg_read(wm831x, reg);
-	if (val < 0)
-		return val;
-
-	val = (val & WM831X_DC1_HC_THR_MASK) >> WM831X_DC1_HC_THR_SHIFT;
-	return wm831x_dcdc_ilim[val];
-}
-
 static const struct regulator_ops wm831x_buckv_ops = {
 	.set_voltage_sel = wm831x_buckv_set_voltage_sel,
 	.get_voltage_sel = wm831x_buckv_get_voltage_sel,
-	.list_voltage = wm831x_buckv_list_voltage,
-	.map_voltage = wm831x_buckv_map_voltage,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
 	.set_suspend_voltage = wm831x_buckv_set_suspend_voltage,
-	.set_current_limit = wm831x_buckv_set_current_limit,
-	.get_current_limit = wm831x_buckv_get_current_limit,
+	.set_current_limit = regulator_set_current_limit_regmap,
+	.get_current_limit = regulator_get_current_limit_regmap,
 
 	.is_enabled = regulator_is_enabled_regmap,
 	.enable = regulator_enable_regmap,
@@ -492,10 +435,16 @@ static int wm831x_buckv_probe(struct platform_device *pdev)
 	dcdc->desc.id = id;
 	dcdc->desc.type = REGULATOR_VOLTAGE;
 	dcdc->desc.n_voltages = WM831X_BUCKV_MAX_SELECTOR + 1;
+	dcdc->desc.linear_ranges = wm831x_buckv_ranges;
+	dcdc->desc.n_linear_ranges = ARRAY_SIZE(wm831x_buckv_ranges);
 	dcdc->desc.ops = &wm831x_buckv_ops;
 	dcdc->desc.owner = THIS_MODULE;
 	dcdc->desc.enable_reg = WM831X_DCDC_ENABLE;
 	dcdc->desc.enable_mask = 1 << id;
+	dcdc->desc.csel_reg = dcdc->base + WM831X_DCDC_CONTROL_2;
+	dcdc->desc.csel_mask = WM831X_DC1_HC_THR_MASK;
+	dcdc->desc.n_current_limits = ARRAY_SIZE(wm831x_dcdc_ilim);
+	dcdc->desc.curr_table = wm831x_dcdc_ilim;
 
 	ret = wm831x_reg_read(wm831x, dcdc->base + WM831X_DCDC_ON_CONFIG);
 	if (ret < 0) {
diff --git a/include/linux/mfd/tps65218.h b/include/linux/mfd/tps65218.h
index c204d9a79436..45cdcd0fee53 100644
--- a/include/linux/mfd/tps65218.h
+++ b/include/linux/mfd/tps65218.h
@@ -208,6 +208,7 @@ enum tps65218_regulator_id {
 	/* LDOs */
 	TPS65218_LDO_1,
 	/* LS's */
+	TPS65218_LS_2,
 	TPS65218_LS_3,
 };
 
@@ -218,7 +219,7 @@ enum tps65218_regulator_id {
 /* Number of LDO voltage regulators available */
 #define TPS65218_NUM_LDO		1
 /* Number of total LS current regulators available */
-#define TPS65218_NUM_LS			1
+#define TPS65218_NUM_LS			2
 /* Number of total regulators available */
 #define TPS65218_NUM_REGULATOR		(TPS65218_NUM_DCDC + TPS65218_NUM_LDO \
 					 + TPS65218_NUM_LS)
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 389bcaf7900f..377da2357118 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -264,6 +264,7 @@ enum regulator_type {
  * @continuous_voltage_range: Indicates if the regulator can set any
  *                            voltage within constrains range.
  * @n_voltages: Number of selectors available for ops.list_voltage().
+ * @n_current_limits: Number of selectors available for current limits
  *
  * @min_uV: Voltage given by the lowest selector (if linear mapping)
  * @uV_step: Voltage increase with each selector (if linear mapping)
@@ -278,14 +279,15 @@ enum regulator_type {
  * @n_linear_ranges: Number of entries in the @linear_ranges (and in
  *		     linear_range_selectors if used) table(s).
  * @volt_table: Voltage mapping table (if table based mapping)
+ * @curr_table: Current limit mapping table (if table based mapping)
  *
  * @vsel_range_reg: Register for range selector when using pickable ranges
  *		    and regulator_regmap_X_voltage_X_pickable functions.
  * @vsel_range_mask: Mask for register bitfield used for range selector
  * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_
  * @vsel_mask: Mask for register bitfield used for selector
- * @csel_reg: Register for TPS65218 LS3 current regulator
- * @csel_mask: Mask for TPS65218 LS3 current regulator
+ * @csel_reg: Register for current limit selector using regmap set_current_limit
+ * @csel_mask: Mask for register bitfield used for current limit selector
  * @apply_reg: Register for initiate voltage change on the output when
  *                using regulator_set_voltage_sel_regmap
  * @apply_bit: Register bitfield used for initiate voltage change on the
@@ -333,6 +335,7 @@ struct regulator_desc {
 	int id;
 	unsigned int continuous_voltage_range:1;
 	unsigned n_voltages;
+	unsigned int n_current_limits;
 	const struct regulator_ops *ops;
 	int irq;
 	enum regulator_type type;
@@ -351,6 +354,7 @@ struct regulator_desc {
 	int n_linear_ranges;
 
 	const unsigned int *volt_table;
+	const unsigned int *curr_table;
 
 	unsigned int vsel_range_reg;
 	unsigned int vsel_range_mask;
@@ -401,13 +405,7 @@ struct regulator_desc {
  *           NULL).
  * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is
  *          insufficient.
- * @ena_gpio_initialized: GPIO controlling regulator enable was properly
- *                        initialized, meaning that >= 0 is a valid gpio
- *                        identifier and < 0 is a non existent gpio.
- * @ena_gpio: GPIO controlling regulator enable.
- * @ena_gpiod: GPIO descriptor controlling regulator enable.
- * @ena_gpio_invert: Sense for GPIO enable control.
- * @ena_gpio_flags: Flags to use when calling gpio_request_one()
+ * @ena_gpiod: GPIO controlling regulator enable.
  */
 struct regulator_config {
 	struct device *dev;
@@ -416,11 +414,7 @@ struct regulator_config {
 	struct device_node *of_node;
 	struct regmap *regmap;
 
-	bool ena_gpio_initialized;
-	int ena_gpio;
 	struct gpio_desc *ena_gpiod;
-	unsigned int ena_gpio_invert:1;
-	unsigned int ena_gpio_flags;
 };
 
 /*
@@ -503,6 +497,7 @@ int regulator_notifier_call_chain(struct regulator_dev *rdev,
 
 void *rdev_get_drvdata(struct regulator_dev *rdev);
 struct device *rdev_get_dev(struct regulator_dev *rdev);
+struct regmap *rdev_get_regmap(struct regulator_dev *rdev);
 int rdev_get_id(struct regulator_dev *rdev);
 
 int regulator_mode_to_status(unsigned int);
@@ -543,9 +538,18 @@ int regulator_set_pull_down_regmap(struct regulator_dev *rdev);
 
 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
 					  bool enable);
+int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
+				       int min_uA, int max_uA);
+int regulator_get_current_limit_regmap(struct regulator_dev *rdev);
 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
 
 void regulator_lock(struct regulator_dev *rdev);
 void regulator_unlock(struct regulator_dev *rdev);
 
+/*
+ * Helper functions intended to be used by regulator drivers prior registering
+ * their regulators.
+ */
+int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc,
+					     unsigned int selector);
 #endif
diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h
index 1a4340ed8e2b..f10140da7145 100644
--- a/include/linux/regulator/fixed.h
+++ b/include/linux/regulator/fixed.h
@@ -25,14 +25,6 @@ struct regulator_init_data;
  * @input_supply:	Name of the input regulator supply
  * @microvolts:		Output voltage of regulator
  * @startup_delay:	Start-up time in microseconds
- * @gpio_is_open_drain: Gpio pin is open drain or normal type.
- *			If it is open drain type then HIGH will be set
- *			through PULL-UP with setting gpio as input
- *			and low will be set as gpio-output with driven
- *			to low. For non-open-drain case, the gpio will
- *			will be in output and drive to low/high accordingly.
- * @enable_high:	Polarity of enable GPIO
- *			1 = Active high, 0 = Active low
  * @enabled_at_boot:	Whether regulator has been enabled at
  * 			boot or not. 1 = Yes, 0 = No
  * 			This is used to keep the regulator at
@@ -48,8 +40,6 @@ struct fixed_voltage_config {
 	const char *input_supply;
 	int microvolts;
 	unsigned startup_delay;
-	unsigned gpio_is_open_drain:1;
-	unsigned enable_high:1;
 	unsigned enabled_at_boot:1;
 	struct regulator_init_data *init_data;
 };
diff --git a/include/linux/regulator/gpio-regulator.h b/include/linux/regulator/gpio-regulator.h
index 19fbd267406d..11cd6375215d 100644
--- a/include/linux/regulator/gpio-regulator.h
+++ b/include/linux/regulator/gpio-regulator.h
@@ -21,6 +21,8 @@
 #ifndef __REGULATOR_GPIO_H
 #define __REGULATOR_GPIO_H
 
+#include <linux/gpio/consumer.h>
+
 struct regulator_init_data;
 
 enum regulator_type;
@@ -44,18 +46,14 @@ struct gpio_regulator_state {
 /**
  * struct gpio_regulator_config - config structure
  * @supply_name:	Name of the regulator supply
- * @enable_gpio:	GPIO to use for enable control
- *			set to -EINVAL if not used
- * @enable_high:	Polarity of enable GPIO
- *			1 = Active high, 0 = Active low
  * @enabled_at_boot:	Whether regulator has been enabled at
  *			boot or not. 1 = Yes, 0 = No
  *			This is used to keep the regulator at
  *			the default state
  * @startup_delay:	Start-up time in microseconds
- * @gpios:		Array containing the gpios needed to control
- *			the setting of the regulator
- * @nr_gpios:		Number of gpios
+ * @gflags:		Array of GPIO configuration flags for initial
+ *			states
+ * @ngpios:		Number of GPIOs and configurations available
  * @states:		Array of gpio_regulator_state entries describing
  *			the gpio state for specific voltages
  * @nr_states:		Number of states available
@@ -69,13 +67,11 @@ struct gpio_regulator_state {
 struct gpio_regulator_config {
 	const char *supply_name;
 
-	int enable_gpio;
-	unsigned enable_high:1;
 	unsigned enabled_at_boot:1;
 	unsigned startup_delay;
 
-	struct gpio *gpios;
-	int nr_gpios;
+	enum gpiod_flags *gflags;
+	int ngpios;
 
 	struct gpio_regulator_state *states;
 	int nr_states;