Merge branch 'pci/host-v3-semi' into next

* pci/host-v3-semi:
  PCI: v3-semi: Add V3 Semiconductor PCI host driver
  PCI: v3: Update the device tree bindings

5 files changed, 1041 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt
index 30b364e504ba..11063293f761 100644
--- a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt
+++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt
@@ -2,14 +2,75 @@ V3 Semiconductor V360 EPC PCI bridge
 
 This bridge is found in the ARM Integrator/AP (Application Platform)
 
-Integrator-specific notes:
+Required properties:
+- compatible: should be one of:
+  "v3,v360epc-pci"
+  "arm,integrator-ap-pci", "v3,v360epc-pci"
+- reg: should contain two register areas:
+  first the base address of the V3 host bridge controller, 64KB
+  second the configuration area register space, 16MB
+- interrupts: should contain a reference to the V3 error interrupt
+  as routed on the system.
+- bus-range: see pci.txt
+- ranges: this follows the standard PCI bindings in the IEEE Std
+  1275-1994 (see pci.txt) with the following restriction:
+  - The non-prefetchable and prefetchable memory windows must
+    each be exactly 256MB (0x10000000) in size.
+  - The prefetchable memory window must be immediately adjacent
+    to the non-prefetcable memory window
+- dma-ranges: three ranges for the inbound memory region. The ranges must
+  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB,
+  64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked
+  as pre-fetchable. Two ranges are supported by the hardware.
 
-- syscon: should contain a link to the syscon device node (since
+Integrator-specific required properties:
+- syscon: should contain a link to the syscon device node, since
   on the Integrator, some registers in the syscon are required to
-  operate the V3).
+  operate the V3 host bridge.
 
-V360 EPC specific notes:
+Example:
 
-- reg: should contain the base address of the V3 adapter.
-- interrupts: should contain a reference to the V3 error interrupt
-  as routed on the system.
+pci: pciv3@62000000 {
+	compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+	reg = <0x62000000 0x10000>, <0x61000000 0x01000000>;
+	interrupt-parent = <&pic>;
+	interrupts = <17>; /* Bus error IRQ */
+	clocks = <&pciclk>;
+	bus-range = <0x00 0xff>;
+	ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */
+		0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */
+		0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */
+		0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */
+		0x42000000 0 0x50000000 /* prefetchable memory @50000000 */
+		0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */
+	dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */
+		0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */
+		0x02000000 0 0x80000000 /* Core module alias memory */
+		0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */
+	interrupt-map-mask = <0xf800 0 0 0x7>;
+	interrupt-map = <
+	/* IDSEL 9 */
+	0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */
+	0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */
+	0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */
+	0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */
+	/* IDSEL 10 */
+	0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */
+	0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */
+	0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */
+	0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */
+	/* IDSEL 11 */
+	0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */
+	0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */
+	0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */
+	0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */
+	/* IDSEL 12 */
+	0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */
+	0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */
+	0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */
+	0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */
+	>;
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 2a3501cfd201..ca456a870731 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10511,6 +10511,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/pci/rockchip-pcie.txt
 F:	drivers/pci/host/pcie-rockchip.c
 
+PCI DRIVER FOR V3 SEMICONDUCTOR V360EPC
+M:	Linus Walleij <linus.walleij@linaro.org>
+L:	linux-pci@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt
+F:	drivers/pci/host/pci-v3-semi.c
+
 PCIE DRIVER FOR ST SPEAR13XX
 M:	Pratyush Anand <pratyush.anand@gmail.com>
 L:	linux-pci@vger.kernel.org
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index b868803792d8..38d12980db0f 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -95,6 +95,12 @@ config PCI_XGENE_MSI
 	  Say Y here if you want PCIe MSI support for the APM X-Gene v1 SoC.
 	  This MSI driver supports 5 PCIe ports on the APM X-Gene v1 SoC.
 
+config PCI_V3_SEMI
+	bool "V3 Semiconductor PCI controller"
+	depends on OF
+	depends on ARM
+	default ARCH_INTEGRATOR_AP
+
 config PCI_VERSATILE
 	bool "ARM Versatile PB PCI controller"
 	depends on ARCH_VERSATILE
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 12382785e02a..ee7cd492bb7f 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_PCI_HOST_COMMON) += pci-host-common.o
 obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
 obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
 obj-$(CONFIG_PCIE_XILINX_NWL) += pcie-xilinx-nwl.o
+obj-$(CONFIG_PCI_V3_SEMI) += pci-v3-semi.o
 obj-$(CONFIG_PCI_XGENE_MSI) += pci-xgene-msi.o
 obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o
 obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o
diff --git a/drivers/pci/host/pci-v3-semi.c b/drivers/pci/host/pci-v3-semi.c
new file mode 100644
index 000000000000..02f6e1e3a421
--- /dev/null
+++ b/drivers/pci/host/pci-v3-semi.c
@@ -0,0 +1,959 @@
+/*
+ * Support for V3 Semiconductor PCI Local Bus to PCI Bridge
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ *
+ * Based on the code from arch/arm/mach-integrator/pci_v3.c
+ * Copyright (C) 1999 ARM Limited
+ * Copyright (C) 2000-2001 Deep Blue Solutions Ltd
+ *
+ * Contributors to the old driver include:
+ * Russell King <linux@armlinux.org.uk>
+ * David A. Rusling <david.rusling@linaro.org> (uHAL, ARM Firmware suite)
+ * Rob Herring <robh@kernel.org>
+ * Liviu Dudau <Liviu.Dudau@arm.com>
+ * Grant Likely <grant.likely@secretlab.ca>
+ * Arnd Bergmann <arnd@arndb.de>
+ * Bjorn Helgaas <bhelgaas@google.com>
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/bitops.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+
+#define V3_PCI_VENDOR			0x00000000
+#define V3_PCI_DEVICE			0x00000002
+#define V3_PCI_CMD			0x00000004
+#define V3_PCI_STAT			0x00000006
+#define V3_PCI_CC_REV			0x00000008
+#define V3_PCI_HDR_CFG			0x0000000C
+#define V3_PCI_IO_BASE			0x00000010
+#define V3_PCI_BASE0			0x00000014
+#define V3_PCI_BASE1			0x00000018
+#define V3_PCI_SUB_VENDOR		0x0000002C
+#define V3_PCI_SUB_ID			0x0000002E
+#define V3_PCI_ROM			0x00000030
+#define V3_PCI_BPARAM			0x0000003C
+#define V3_PCI_MAP0			0x00000040
+#define V3_PCI_MAP1			0x00000044
+#define V3_PCI_INT_STAT			0x00000048
+#define V3_PCI_INT_CFG			0x0000004C
+#define V3_LB_BASE0			0x00000054
+#define V3_LB_BASE1			0x00000058
+#define V3_LB_MAP0			0x0000005E
+#define V3_LB_MAP1			0x00000062
+#define V3_LB_BASE2			0x00000064
+#define V3_LB_MAP2			0x00000066
+#define V3_LB_SIZE			0x00000068
+#define V3_LB_IO_BASE			0x0000006E
+#define V3_FIFO_CFG			0x00000070
+#define V3_FIFO_PRIORITY		0x00000072
+#define V3_FIFO_STAT			0x00000074
+#define V3_LB_ISTAT			0x00000076
+#define V3_LB_IMASK			0x00000077
+#define V3_SYSTEM			0x00000078
+#define V3_LB_CFG			0x0000007A
+#define V3_PCI_CFG			0x0000007C
+#define V3_DMA_PCI_ADR0			0x00000080
+#define V3_DMA_PCI_ADR1			0x00000090
+#define V3_DMA_LOCAL_ADR0		0x00000084
+#define V3_DMA_LOCAL_ADR1		0x00000094
+#define V3_DMA_LENGTH0			0x00000088
+#define V3_DMA_LENGTH1			0x00000098
+#define V3_DMA_CSR0			0x0000008B
+#define V3_DMA_CSR1			0x0000009B
+#define V3_DMA_CTLB_ADR0		0x0000008C
+#define V3_DMA_CTLB_ADR1		0x0000009C
+#define V3_DMA_DELAY			0x000000E0
+#define V3_MAIL_DATA			0x000000C0
+#define V3_PCI_MAIL_IEWR		0x000000D0
+#define V3_PCI_MAIL_IERD		0x000000D2
+#define V3_LB_MAIL_IEWR			0x000000D4
+#define V3_LB_MAIL_IERD			0x000000D6
+#define V3_MAIL_WR_STAT			0x000000D8
+#define V3_MAIL_RD_STAT			0x000000DA
+#define V3_QBA_MAP			0x000000DC
+
+/* PCI STATUS bits */
+#define V3_PCI_STAT_PAR_ERR		BIT(15)
+#define V3_PCI_STAT_SYS_ERR		BIT(14)
+#define V3_PCI_STAT_M_ABORT_ERR		BIT(13)
+#define V3_PCI_STAT_T_ABORT_ERR		BIT(12)
+
+/* LB ISTAT bits */
+#define V3_LB_ISTAT_MAILBOX		BIT(7)
+#define V3_LB_ISTAT_PCI_RD		BIT(6)
+#define V3_LB_ISTAT_PCI_WR		BIT(5)
+#define V3_LB_ISTAT_PCI_INT		BIT(4)
+#define V3_LB_ISTAT_PCI_PERR		BIT(3)
+#define V3_LB_ISTAT_I2O_QWR		BIT(2)
+#define V3_LB_ISTAT_DMA1		BIT(1)
+#define V3_LB_ISTAT_DMA0		BIT(0)
+
+/* PCI COMMAND bits */
+#define V3_COMMAND_M_FBB_EN		BIT(9)
+#define V3_COMMAND_M_SERR_EN		BIT(8)
+#define V3_COMMAND_M_PAR_EN		BIT(6)
+#define V3_COMMAND_M_MASTER_EN		BIT(2)
+#define V3_COMMAND_M_MEM_EN		BIT(1)
+#define V3_COMMAND_M_IO_EN		BIT(0)
+
+/* SYSTEM bits */
+#define V3_SYSTEM_M_RST_OUT		BIT(15)
+#define V3_SYSTEM_M_LOCK		BIT(14)
+#define V3_SYSTEM_UNLOCK		0xa05f
+
+/* PCI CFG bits */
+#define V3_PCI_CFG_M_I2O_EN		BIT(15)
+#define V3_PCI_CFG_M_IO_REG_DIS		BIT(14)
+#define V3_PCI_CFG_M_IO_DIS		BIT(13)
+#define V3_PCI_CFG_M_EN3V		BIT(12)
+#define V3_PCI_CFG_M_RETRY_EN		BIT(10)
+#define V3_PCI_CFG_M_AD_LOW1		BIT(9)
+#define V3_PCI_CFG_M_AD_LOW0		BIT(8)
+/*
+ * This is the value applied to C/BE[3:1], with bit 0 always held 0
+ * during DMA access.
+ */
+#define V3_PCI_CFG_M_RTYPE_SHIFT	5
+#define V3_PCI_CFG_M_WTYPE_SHIFT	1
+#define V3_PCI_CFG_TYPE_DEFAULT		0x3
+
+/* PCI BASE bits (PCI -> Local Bus) */
+#define V3_PCI_BASE_M_ADR_BASE		0xFFF00000U
+#define V3_PCI_BASE_M_ADR_BASEL		0x000FFF00U
+#define V3_PCI_BASE_M_PREFETCH		BIT(3)
+#define V3_PCI_BASE_M_TYPE		(3 << 1)
+#define V3_PCI_BASE_M_IO		BIT(0)
+
+/* PCI MAP bits (PCI -> Local bus) */
+#define V3_PCI_MAP_M_MAP_ADR		0xFFF00000U
+#define V3_PCI_MAP_M_RD_POST_INH	BIT(15)
+#define V3_PCI_MAP_M_ROM_SIZE		(3 << 10)
+#define V3_PCI_MAP_M_SWAP		(3 << 8)
+#define V3_PCI_MAP_M_ADR_SIZE		0x000000F0U
+#define V3_PCI_MAP_M_REG_EN		BIT(1)
+#define V3_PCI_MAP_M_ENABLE		BIT(0)
+
+/* LB_BASE0,1 bits (Local bus -> PCI) */
+#define V3_LB_BASE_ADR_BASE		0xfff00000U
+#define V3_LB_BASE_SWAP			(3 << 8)
+#define V3_LB_BASE_ADR_SIZE		(15 << 4)
+#define V3_LB_BASE_PREFETCH		BIT(3)
+#define V3_LB_BASE_ENABLE		BIT(0)
+
+#define V3_LB_BASE_ADR_SIZE_1MB		(0 << 4)
+#define V3_LB_BASE_ADR_SIZE_2MB		(1 << 4)
+#define V3_LB_BASE_ADR_SIZE_4MB		(2 << 4)
+#define V3_LB_BASE_ADR_SIZE_8MB		(3 << 4)
+#define V3_LB_BASE_ADR_SIZE_16MB	(4 << 4)
+#define V3_LB_BASE_ADR_SIZE_32MB	(5 << 4)
+#define V3_LB_BASE_ADR_SIZE_64MB	(6 << 4)
+#define V3_LB_BASE_ADR_SIZE_128MB	(7 << 4)
+#define V3_LB_BASE_ADR_SIZE_256MB	(8 << 4)
+#define V3_LB_BASE_ADR_SIZE_512MB	(9 << 4)
+#define V3_LB_BASE_ADR_SIZE_1GB		(10 << 4)
+#define V3_LB_BASE_ADR_SIZE_2GB		(11 << 4)
+
+#define v3_addr_to_lb_base(a)	((a) & V3_LB_BASE_ADR_BASE)
+
+/* LB_MAP0,1 bits (Local bus -> PCI) */
+#define V3_LB_MAP_MAP_ADR		0xfff0U
+#define V3_LB_MAP_TYPE			(7 << 1)
+#define V3_LB_MAP_AD_LOW_EN		BIT(0)
+
+#define V3_LB_MAP_TYPE_IACK		(0 << 1)
+#define V3_LB_MAP_TYPE_IO		(1 << 1)
+#define V3_LB_MAP_TYPE_MEM		(3 << 1)
+#define V3_LB_MAP_TYPE_CONFIG		(5 << 1)
+#define V3_LB_MAP_TYPE_MEM_MULTIPLE	(6 << 1)
+
+#define v3_addr_to_lb_map(a)	(((a) >> 16) & V3_LB_MAP_MAP_ADR)
+
+/* LB_BASE2 bits (Local bus -> PCI IO) */
+#define V3_LB_BASE2_ADR_BASE		0xff00U
+#define V3_LB_BASE2_SWAP_AUTO		(3 << 6)
+#define V3_LB_BASE2_ENABLE		BIT(0)
+
+#define v3_addr_to_lb_base2(a)	(((a) >> 16) & V3_LB_BASE2_ADR_BASE)
+
+/* LB_MAP2 bits (Local bus -> PCI IO) */
+#define V3_LB_MAP2_MAP_ADR		0xff00U
+
+#define v3_addr_to_lb_map2(a)	(((a) >> 16) & V3_LB_MAP2_MAP_ADR)
+
+/* FIFO priority bits */
+#define V3_FIFO_PRIO_LOCAL		BIT(12)
+#define V3_FIFO_PRIO_LB_RD1_FLUSH_EOB	BIT(10)
+#define V3_FIFO_PRIO_LB_RD1_FLUSH_AP1	BIT(11)
+#define V3_FIFO_PRIO_LB_RD1_FLUSH_ANY	(BIT(10)|BIT(11))
+#define V3_FIFO_PRIO_LB_RD0_FLUSH_EOB	BIT(8)
+#define V3_FIFO_PRIO_LB_RD0_FLUSH_AP1	BIT(9)
+#define V3_FIFO_PRIO_LB_RD0_FLUSH_ANY	(BIT(8)|BIT(9))
+#define V3_FIFO_PRIO_PCI		BIT(4)
+#define V3_FIFO_PRIO_PCI_RD1_FLUSH_EOB	BIT(2)
+#define V3_FIFO_PRIO_PCI_RD1_FLUSH_AP1	BIT(3)
+#define V3_FIFO_PRIO_PCI_RD1_FLUSH_ANY	(BIT(2)|BIT(3))
+#define V3_FIFO_PRIO_PCI_RD0_FLUSH_EOB	BIT(0)
+#define V3_FIFO_PRIO_PCI_RD0_FLUSH_AP1	BIT(1)
+#define V3_FIFO_PRIO_PCI_RD0_FLUSH_ANY	(BIT(0)|BIT(1))
+
+/* Local bus configuration bits */
+#define V3_LB_CFG_LB_TO_64_CYCLES	0x0000
+#define V3_LB_CFG_LB_TO_256_CYCLES	BIT(13)
+#define V3_LB_CFG_LB_TO_512_CYCLES	BIT(14)
+#define V3_LB_CFG_LB_TO_1024_CYCLES	(BIT(13)|BIT(14))
+#define V3_LB_CFG_LB_RST		BIT(12)
+#define V3_LB_CFG_LB_PPC_RDY		BIT(11)
+#define V3_LB_CFG_LB_LB_INT		BIT(10)
+#define V3_LB_CFG_LB_ERR_EN		BIT(9)
+#define V3_LB_CFG_LB_RDY_EN		BIT(8)
+#define V3_LB_CFG_LB_BE_IMODE		BIT(7)
+#define V3_LB_CFG_LB_BE_OMODE		BIT(6)
+#define V3_LB_CFG_LB_ENDIAN		BIT(5)
+#define V3_LB_CFG_LB_PARK_EN		BIT(4)
+#define V3_LB_CFG_LB_FBB_DIS		BIT(2)
+
+/* ARM Integrator-specific extended control registers */
+#define INTEGRATOR_SC_PCI_OFFSET	0x18
+#define INTEGRATOR_SC_PCI_ENABLE	BIT(0)
+#define INTEGRATOR_SC_PCI_INTCLR	BIT(1)
+#define INTEGRATOR_SC_LBFADDR_OFFSET	0x20
+#define INTEGRATOR_SC_LBFCODE_OFFSET	0x24
+
+struct v3_pci {
+	struct device *dev;
+	void __iomem *base;
+	void __iomem *config_base;
+	struct pci_bus *bus;
+	u32 config_mem;
+	u32 io_mem;
+	u32 non_pre_mem;
+	u32 pre_mem;
+	phys_addr_t io_bus_addr;
+	phys_addr_t non_pre_bus_addr;
+	phys_addr_t pre_bus_addr;
+	struct regmap *map;
+};
+
+/*
+ * The V3 PCI interface chip in Integrator provides several windows from
+ * local bus memory into the PCI memory areas. Unfortunately, there
+ * are not really enough windows for our usage, therefore we reuse
+ * one of the windows for access to PCI configuration space. On the
+ * Integrator/AP, the memory map is as follows:
+ *
+ * Local Bus Memory         Usage
+ *
+ * 40000000 - 4FFFFFFF      PCI memory.  256M non-prefetchable
+ * 50000000 - 5FFFFFFF      PCI memory.  256M prefetchable
+ * 60000000 - 60FFFFFF      PCI IO.  16M
+ * 61000000 - 61FFFFFF      PCI Configuration. 16M
+ *
+ * There are three V3 windows, each described by a pair of V3 registers.
+ * These are LB_BASE0/LB_MAP0, LB_BASE1/LB_MAP1 and LB_BASE2/LB_MAP2.
+ * Base0 and Base1 can be used for any type of PCI memory access.   Base2
+ * can be used either for PCI I/O or for I20 accesses.  By default, uHAL
+ * uses this only for PCI IO space.
+ *
+ * Normally these spaces are mapped using the following base registers:
+ *
+ * Usage Local Bus Memory         Base/Map registers used
+ *
+ * Mem   40000000 - 4FFFFFFF      LB_BASE0/LB_MAP0
+ * Mem   50000000 - 5FFFFFFF      LB_BASE1/LB_MAP1
+ * IO    60000000 - 60FFFFFF      LB_BASE2/LB_MAP2
+ * Cfg   61000000 - 61FFFFFF
+ *
+ * This means that I20 and PCI configuration space accesses will fail.
+ * When PCI configuration accesses are needed (via the uHAL PCI
+ * configuration space primitives) we must remap the spaces as follows:
+ *
+ * Usage Local Bus Memory         Base/Map registers used
+ *
+ * Mem   40000000 - 4FFFFFFF      LB_BASE0/LB_MAP0
+ * Mem   50000000 - 5FFFFFFF      LB_BASE0/LB_MAP0
+ * IO    60000000 - 60FFFFFF      LB_BASE2/LB_MAP2
+ * Cfg   61000000 - 61FFFFFF      LB_BASE1/LB_MAP1
+ *
+ * To make this work, the code depends on overlapping windows working.
+ * The V3 chip translates an address by checking its range within
+ * each of the BASE/MAP pairs in turn (in ascending register number
+ * order).  It will use the first matching pair.   So, for example,
+ * if the same address is mapped by both LB_BASE0/LB_MAP0 and
+ * LB_BASE1/LB_MAP1, the V3 will use the translation from
+ * LB_BASE0/LB_MAP0.
+ *
+ * To allow PCI Configuration space access, the code enlarges the
+ * window mapped by LB_BASE0/LB_MAP0 from 256M to 512M.  This occludes
+ * the windows currently mapped by LB_BASE1/LB_MAP1 so that it can
+ * be remapped for use by configuration cycles.
+ *
+ * At the end of the PCI Configuration space accesses,
+ * LB_BASE1/LB_MAP1 is reset to map PCI Memory.  Finally the window
+ * mapped by LB_BASE0/LB_MAP0 is reduced in size from 512M to 256M to
+ * reveal the now restored LB_BASE1/LB_MAP1 window.
+ *
+ * NOTE: We do not set up I2O mapping.  I suspect that this is only
+ * for an intelligent (target) device.  Using I2O disables most of
+ * the mappings into PCI memory.
+ */
+static void __iomem *v3_map_bus(struct pci_bus *bus,
+				unsigned int devfn, int offset)
+{
+	struct v3_pci *v3 = bus->sysdata;
+	unsigned int address, mapaddress, busnr;
+
+	busnr = bus->number;
+	if (busnr == 0) {
+		int slot = PCI_SLOT(devfn);
+
+		/*
+		 * local bus segment so need a type 0 config cycle
+		 *
+		 * build the PCI configuration "address" with one-hot in
+		 * A31-A11
+		 *
+		 * mapaddress:
+		 *  3:1 = config cycle (101)
+		 *  0   = PCI A1 & A0 are 0 (0)
+		 */
+		address = PCI_FUNC(devfn) << 8;
+		mapaddress = V3_LB_MAP_TYPE_CONFIG;
+
+		if (slot > 12)
+			/*
+			 * high order bits are handled by the MAP register
+			 */
+			mapaddress |= BIT(slot - 5);
+		else
+			/*
+			 * low order bits handled directly in the address
+			 */
+			address |= BIT(slot + 11);
+	} else {
+		/*
+		 * not the local bus segment so need a type 1 config cycle
+		 *
+		 * address:
+		 *  23:16 = bus number
+		 *  15:11 = slot number (7:3 of devfn)
+		 *  10:8  = func number (2:0 of devfn)
+		 *
+		 * mapaddress:
+		 *  3:1 = config cycle (101)
+		 *  0   = PCI A1 & A0 from host bus (1)
+		 */
+		mapaddress = V3_LB_MAP_TYPE_CONFIG | V3_LB_MAP_AD_LOW_EN;
+		address = (busnr << 16) | (devfn << 8);
+	}
+
+	/*
+	 * Set up base0 to see all 512Mbytes of memory space (not
+	 * prefetchable), this frees up base1 for re-use by
+	 * configuration memory
+	 */
+	writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+	       V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE,
+	       v3->base + V3_LB_BASE0);
+
+	/*
+	 * Set up base1/map1 to point into configuration space.
+	 * The config mem is always 16MB.
+	 */
+	writel(v3_addr_to_lb_base(v3->config_mem) |
+	       V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE,
+	       v3->base + V3_LB_BASE1);
+	writew(mapaddress, v3->base + V3_LB_MAP1);
+
+	return v3->config_base + address + offset;
+}
+
+static void v3_unmap_bus(struct v3_pci *v3)
+{
+	/*
+	 * Reassign base1 for use by prefetchable PCI memory
+	 */
+	writel(v3_addr_to_lb_base(v3->pre_mem) |
+	       V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH |
+	       V3_LB_BASE_ENABLE,
+	       v3->base + V3_LB_BASE1);
+	writew(v3_addr_to_lb_map(v3->pre_bus_addr) |
+	       V3_LB_MAP_TYPE_MEM, /* was V3_LB_MAP_TYPE_MEM_MULTIPLE */
+	       v3->base + V3_LB_MAP1);
+
+	/*
+	 * And shrink base0 back to a 256M window (NOTE: MAP0 already correct)
+	 */
+	writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+	       V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE,
+	       v3->base + V3_LB_BASE0);
+}
+
+static int v3_pci_read_config(struct pci_bus *bus, unsigned int fn,
+			      int config, int size, u32 *value)
+{
+	struct v3_pci *v3 = bus->sysdata;
+	int ret;
+
+	dev_dbg(&bus->dev,
+		"[read]  slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+		PCI_SLOT(fn), PCI_FUNC(fn), config, size, *value);
+	ret = pci_generic_config_read(bus, fn, config, size, value);
+	v3_unmap_bus(v3);
+	return ret;
+}
+
+static int v3_pci_write_config(struct pci_bus *bus, unsigned int fn,
+				    int config, int size, u32 value)
+{
+	struct v3_pci *v3 = bus->sysdata;
+	int ret;
+
+	dev_dbg(&bus->dev,
+		"[write] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+		PCI_SLOT(fn), PCI_FUNC(fn), config, size, value);
+	ret = pci_generic_config_write(bus, fn, config, size, value);
+	v3_unmap_bus(v3);
+	return ret;
+}
+
+static struct pci_ops v3_pci_ops = {
+	.map_bus = v3_map_bus,
+	.read = v3_pci_read_config,
+	.write = v3_pci_write_config,
+};
+
+static irqreturn_t v3_irq(int irq, void *data)
+{
+	struct v3_pci *v3 = data;
+	struct device *dev = v3->dev;
+	u32 status;
+
+	status = readw(v3->base + V3_PCI_STAT);
+	if (status & V3_PCI_STAT_PAR_ERR)
+		dev_err(dev, "parity error interrupt\n");
+	if (status & V3_PCI_STAT_SYS_ERR)
+		dev_err(dev, "system error interrupt\n");
+	if (status & V3_PCI_STAT_M_ABORT_ERR)
+		dev_err(dev, "master abort error interrupt\n");
+	if (status & V3_PCI_STAT_T_ABORT_ERR)
+		dev_err(dev, "target abort error interrupt\n");
+	writew(status, v3->base + V3_PCI_STAT);
+
+	status = readb(v3->base + V3_LB_ISTAT);
+	if (status & V3_LB_ISTAT_MAILBOX)
+		dev_info(dev, "PCI mailbox interrupt\n");
+	if (status & V3_LB_ISTAT_PCI_RD)
+		dev_err(dev, "PCI target LB->PCI READ abort interrupt\n");
+	if (status & V3_LB_ISTAT_PCI_WR)
+		dev_err(dev, "PCI target LB->PCI WRITE abort interrupt\n");
+	if (status &  V3_LB_ISTAT_PCI_INT)
+		dev_info(dev, "PCI pin interrupt\n");
+	if (status & V3_LB_ISTAT_PCI_PERR)
+		dev_err(dev, "PCI parity error interrupt\n");
+	if (status & V3_LB_ISTAT_I2O_QWR)
+		dev_info(dev, "I2O inbound post queue interrupt\n");
+	if (status & V3_LB_ISTAT_DMA1)
+		dev_info(dev, "DMA channel 1 interrupt\n");
+	if (status & V3_LB_ISTAT_DMA0)
+		dev_info(dev, "DMA channel 0 interrupt\n");
+	/* Clear all possible interrupts on the local bus */
+	writeb(0, v3->base + V3_LB_ISTAT);
+	if (v3->map)
+		regmap_write(v3->map, INTEGRATOR_SC_PCI_OFFSET,
+			     INTEGRATOR_SC_PCI_ENABLE |
+			     INTEGRATOR_SC_PCI_INTCLR);
+
+	return IRQ_HANDLED;
+}
+
+static int v3_integrator_init(struct v3_pci *v3)
+{
+	unsigned int val;
+
+	v3->map =
+		syscon_regmap_lookup_by_compatible("arm,integrator-ap-syscon");
+	if (IS_ERR(v3->map)) {
+		dev_err(v3->dev, "no syscon\n");
+		return -ENODEV;
+	}
+
+	regmap_read(v3->map, INTEGRATOR_SC_PCI_OFFSET, &val);
+	/* Take the PCI bridge out of reset, clear IRQs */
+	regmap_write(v3->map, INTEGRATOR_SC_PCI_OFFSET,
+		     INTEGRATOR_SC_PCI_ENABLE |
+		     INTEGRATOR_SC_PCI_INTCLR);
+
+	if (!(val & INTEGRATOR_SC_PCI_ENABLE)) {
+		/* If we were in reset we need to sleep a bit */
+		msleep(230);
+
+		/* Set the physical base for the controller itself */
+		writel(0x6200, v3->base + V3_LB_IO_BASE);
+
+		/* Wait for the mailbox to settle after reset */
+		do {
+			writeb(0xaa, v3->base + V3_MAIL_DATA);
+			writeb(0x55, v3->base + V3_MAIL_DATA + 4);
+		} while (readb(v3->base + V3_MAIL_DATA) != 0xaa &&
+			 readb(v3->base + V3_MAIL_DATA) != 0x55);
+	}
+
+	dev_info(v3->dev, "initialized PCI V3 Integrator/AP integration\n");
+
+	return 0;
+}
+
+static int v3_pci_setup_resource(struct v3_pci *v3,
+				 resource_size_t io_base,
+				 struct pci_host_bridge *host,
+				 struct resource_entry *win)
+{
+	struct device *dev = v3->dev;
+	struct resource *mem;
+	struct resource *io;
+	int ret;
+
+	switch (resource_type(win->res)) {
+	case IORESOURCE_IO:
+		io = win->res;
+		io->name = "V3 PCI I/O";
+		v3->io_mem = io_base;
+		v3->io_bus_addr = io->start - win->offset;
+		dev_dbg(dev, "I/O window %pR, bus addr %pap\n",
+			io, &v3->io_bus_addr);
+		ret = pci_remap_iospace(io, io_base);
+		if (ret) {
+			dev_warn(dev,
+				 "error %d: failed to map resource %pR\n",
+				 ret, io);
+			return ret;
+		}
+		/* Setup window 2 - PCI I/O */
+		writel(v3_addr_to_lb_base2(v3->io_mem) |
+		       V3_LB_BASE2_ENABLE,
+		       v3->base + V3_LB_BASE2);
+		writew(v3_addr_to_lb_map2(v3->io_bus_addr),
+		       v3->base + V3_LB_MAP2);
+		break;
+	case IORESOURCE_MEM:
+		mem = win->res;
+		if (mem->flags & IORESOURCE_PREFETCH) {
+			mem->name = "V3 PCI PRE-MEM";
+			v3->pre_mem = mem->start;
+			v3->pre_bus_addr = mem->start - win->offset;
+			dev_dbg(dev, "PREFETCHABLE MEM window %pR, bus addr %pap\n",
+				mem, &v3->pre_bus_addr);
+			if (resource_size(mem) != SZ_256M) {
+				dev_err(dev, "prefetchable memory range is not 256MB\n");
+				return -EINVAL;
+			}
+			if (v3->non_pre_mem &&
+			    (mem->start != v3->non_pre_mem + SZ_256M)) {
+				dev_err(dev,
+					"prefetchable memory is not adjacent to non-prefetchable memory\n");
+				return -EINVAL;
+			}
+			/* Setup window 1 - PCI prefetchable memory */
+			writel(v3_addr_to_lb_base(v3->pre_mem) |
+			       V3_LB_BASE_ADR_SIZE_256MB |
+			       V3_LB_BASE_PREFETCH |
+			       V3_LB_BASE_ENABLE,
+			       v3->base + V3_LB_BASE1);
+			writew(v3_addr_to_lb_map(v3->pre_bus_addr) |
+			       V3_LB_MAP_TYPE_MEM, /* Was V3_LB_MAP_TYPE_MEM_MULTIPLE */
+			       v3->base + V3_LB_MAP1);
+		} else {
+			mem->name = "V3 PCI NON-PRE-MEM";
+			v3->non_pre_mem = mem->start;
+			v3->non_pre_bus_addr = mem->start - win->offset;
+			dev_dbg(dev, "NON-PREFETCHABLE MEM window %pR, bus addr %pap\n",
+				mem, &v3->non_pre_bus_addr);
+			if (resource_size(mem) != SZ_256M) {
+				dev_err(dev,
+					"non-prefetchable memory range is not 256MB\n");
+				return -EINVAL;
+			}
+			/* Setup window 0 - PCI non-prefetchable memory */
+			writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+			       V3_LB_BASE_ADR_SIZE_256MB |
+			       V3_LB_BASE_ENABLE,
+			       v3->base + V3_LB_BASE0);
+			writew(v3_addr_to_lb_map(v3->non_pre_bus_addr) |
+			       V3_LB_MAP_TYPE_MEM,
+			       v3->base + V3_LB_MAP0);
+		}
+		break;
+	case IORESOURCE_BUS:
+		dev_dbg(dev, "BUS %pR\n", win->res);
+		host->busnr = win->res->start;
+		break;
+	default:
+		dev_info(dev, "Unknown resource type %lu\n",
+			 resource_type(win->res));
+		break;
+	}
+
+	return 0;
+}
+
+static int v3_get_dma_range_config(struct v3_pci *v3,
+				   struct of_pci_range *range,
+				   u32 *pci_base, u32 *pci_map)
+{
+	struct device *dev = v3->dev;
+	u64 cpu_end = range->cpu_addr + range->size - 1;
+	u64 pci_end = range->pci_addr + range->size - 1;
+	u32 val;
+
+	if (range->pci_addr & ~V3_PCI_BASE_M_ADR_BASE) {
+		dev_err(dev, "illegal range, only PCI bits 31..20 allowed\n");
+		return -EINVAL;
+	}
+	val = ((u32)range->pci_addr) & V3_PCI_BASE_M_ADR_BASE;
+	*pci_base = val;
+
+	if (range->cpu_addr & ~V3_PCI_MAP_M_MAP_ADR) {
+		dev_err(dev, "illegal range, only CPU bits 31..20 allowed\n");
+		return -EINVAL;
+	}
+	val = ((u32)range->cpu_addr) & V3_PCI_MAP_M_MAP_ADR;
+
+	switch (range->size) {
+	case SZ_1M:
+		val |= V3_LB_BASE_ADR_SIZE_1MB;
+		break;
+	case SZ_2M:
+		val |= V3_LB_BASE_ADR_SIZE_2MB;
+		break;
+	case SZ_4M:
+		val |= V3_LB_BASE_ADR_SIZE_4MB;
+		break;
+	case SZ_8M:
+		val |= V3_LB_BASE_ADR_SIZE_8MB;
+		break;
+	case SZ_16M:
+		val |= V3_LB_BASE_ADR_SIZE_16MB;
+		break;
+	case SZ_32M:
+		val |= V3_LB_BASE_ADR_SIZE_32MB;
+		break;
+	case SZ_64M:
+		val |= V3_LB_BASE_ADR_SIZE_64MB;
+		break;
+	case SZ_128M:
+		val |= V3_LB_BASE_ADR_SIZE_128MB;
+		break;
+	case SZ_256M:
+		val |= V3_LB_BASE_ADR_SIZE_256MB;
+		break;
+	case SZ_512M:
+		val |= V3_LB_BASE_ADR_SIZE_512MB;
+		break;
+	case SZ_1G:
+		val |= V3_LB_BASE_ADR_SIZE_1GB;
+		break;
+	case SZ_2G:
+		val |= V3_LB_BASE_ADR_SIZE_2GB;
+		break;
+	default:
+		dev_err(v3->dev, "illegal dma memory chunk size\n");
+		return -EINVAL;
+		break;
+	};
+	val |= V3_PCI_MAP_M_REG_EN | V3_PCI_MAP_M_ENABLE;
+	*pci_map = val;
+
+	dev_dbg(dev,
+		"DMA MEM CPU: 0x%016llx -> 0x%016llx => "
+		"PCI: 0x%016llx -> 0x%016llx base %08x map %08x\n",
+		range->cpu_addr, cpu_end,
+		range->pci_addr, pci_end,
+		*pci_base, *pci_map);
+
+	return 0;
+}
+
+static int v3_pci_parse_map_dma_ranges(struct v3_pci *v3,
+				       struct device_node *np)
+{
+	struct of_pci_range range;
+	struct of_pci_range_parser parser;
+	struct device *dev = v3->dev;
+	int i = 0;
+
+	if (of_pci_dma_range_parser_init(&parser, np)) {
+		dev_err(dev, "missing dma-ranges property\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Get the dma-ranges from the device tree
+	 */
+	for_each_of_pci_range(&parser, &range) {
+		int ret;
+		u32 pci_base, pci_map;
+
+		ret = v3_get_dma_range_config(v3, &range, &pci_base, &pci_map);
+		if (ret)
+			return ret;
+
+		if (i == 0) {
+			writel(pci_base, v3->base + V3_PCI_BASE0);
+			writel(pci_map, v3->base + V3_PCI_MAP0);
+		} else if (i == 1) {
+			writel(pci_base, v3->base + V3_PCI_BASE1);
+			writel(pci_map, v3->base + V3_PCI_MAP1);
+		} else {
+			dev_err(dev, "too many ranges, only two supported\n");
+			dev_err(dev, "range %d ignored\n", i);
+		}
+		i++;
+	}
+	return 0;
+}
+
+static int v3_pci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	resource_size_t io_base;
+	struct resource *regs;
+	struct resource_entry *win;
+	struct v3_pci *v3;
+	struct pci_host_bridge *host;
+	struct clk *clk;
+	u16 val;
+	int irq;
+	int ret;
+	LIST_HEAD(res);
+
+	host = pci_alloc_host_bridge(sizeof(*v3));
+	if (!host)
+		return -ENOMEM;
+
+	host->dev.parent = dev;
+	host->ops = &v3_pci_ops;
+	host->busnr = 0;
+	host->msi = NULL;
+	host->map_irq = of_irq_parse_and_map_pci;
+	host->swizzle_irq = pci_common_swizzle;
+	v3 = pci_host_bridge_priv(host);
+	host->sysdata = v3;
+	v3->dev = dev;
+
+	/* Get and enable host clock */
+	clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(clk)) {
+		dev_err(dev, "clock not found\n");
+		return PTR_ERR(clk);
+	}
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		dev_err(dev, "unable to enable clock\n");
+		return ret;
+	}
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	v3->base = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(v3->base))
+		return PTR_ERR(v3->base);
+	/*
+	 * The hardware has a register with the physical base address
+	 * of the V3 controller itself, verify that this is the same
+	 * as the physical memory we've remapped it from.
+	 */
+	if (readl(v3->base + V3_LB_IO_BASE) != (regs->start >> 16))
+		dev_err(dev, "V3_LB_IO_BASE = %08x but device is @%pR\n",
+			readl(v3->base + V3_LB_IO_BASE), regs);
+
+	/* Configuration space is 16MB directly mapped */
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (resource_size(regs) != SZ_16M) {
+		dev_err(dev, "config mem is not 16MB!\n");
+		return -EINVAL;
+	}
+	v3->config_mem = regs->start;
+	v3->config_base = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(v3->config_base))
+		return PTR_ERR(v3->config_base);
+
+	ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &io_base);
+	if (ret)
+		return ret;
+
+	ret = devm_request_pci_bus_resources(dev, &res);
+	if (ret)
+		return ret;
+
+	/* Get and request error IRQ resource */
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		dev_err(dev, "unable to obtain PCIv3 error IRQ\n");
+		return -ENODEV;
+	}
+	ret = devm_request_irq(dev, irq, v3_irq, 0,
+			"PCIv3 error", v3);
+	if (ret < 0) {
+		dev_err(dev,
+			"unable to request PCIv3 error IRQ %d (%d)\n",
+			irq, ret);
+		return ret;
+	}
+
+	/*
+	 * Unlock V3 registers, but only if they were previously locked.
+	 */
+	if (readw(v3->base + V3_SYSTEM) & V3_SYSTEM_M_LOCK)
+		writew(V3_SYSTEM_UNLOCK, v3->base + V3_SYSTEM);
+
+	/* Disable all slave access while we set up the windows */
+	val = readw(v3->base + V3_PCI_CMD);
+	val &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	writew(val, v3->base + V3_PCI_CMD);
+
+	/* Put the PCI bus into reset */
+	val = readw(v3->base + V3_SYSTEM);
+	val &= ~V3_SYSTEM_M_RST_OUT;
+	writew(val, v3->base + V3_SYSTEM);
+
+	/* Retry until we're ready */
+	val = readw(v3->base + V3_PCI_CFG);
+	val |= V3_PCI_CFG_M_RETRY_EN;
+	writew(val, v3->base + V3_PCI_CFG);
+
+	/* Set up the local bus protocol */
+	val = readw(v3->base + V3_LB_CFG);
+	val |= V3_LB_CFG_LB_BE_IMODE; /* Byte enable input */
+	val |= V3_LB_CFG_LB_BE_OMODE; /* Byte enable output */
+	val &= ~V3_LB_CFG_LB_ENDIAN; /* Little endian */
+	val &= ~V3_LB_CFG_LB_PPC_RDY; /* TODO: when using on PPC403Gx, set to 1 */
+	writew(val, v3->base + V3_LB_CFG);
+
+	/* Enable the PCI bus master */
+	val = readw(v3->base + V3_PCI_CMD);
+	val |= PCI_COMMAND_MASTER;
+	writew(val, v3->base + V3_PCI_CMD);
+
+	/* Get the I/O and memory ranges from DT */
+	resource_list_for_each_entry(win, &res) {
+		ret = v3_pci_setup_resource(v3, io_base, host, win);
+		if (ret) {
+			dev_err(dev, "error setting up resources\n");
+			return ret;
+		}
+	}
+	ret = v3_pci_parse_map_dma_ranges(v3, np);
+	if (ret)
+		return ret;
+
+	/*
+	 * Disable PCI to host IO cycles, enable I/O buffers @3.3V,
+	 * set AD_LOW0 to 1 if one of the LB_MAP registers choose
+	 * to use this (should be unused).
+	 */
+	writel(0x00000000, v3->base + V3_PCI_IO_BASE);
+	val = V3_PCI_CFG_M_IO_REG_DIS | V3_PCI_CFG_M_IO_DIS |
+		V3_PCI_CFG_M_EN3V | V3_PCI_CFG_M_AD_LOW0;
+	/*
+	 * DMA read and write from PCI bus commands types
+	 */
+	val |=  V3_PCI_CFG_TYPE_DEFAULT << V3_PCI_CFG_M_RTYPE_SHIFT;
+	val |=  V3_PCI_CFG_TYPE_DEFAULT << V3_PCI_CFG_M_WTYPE_SHIFT;
+	writew(val, v3->base + V3_PCI_CFG);
+
+	/*
+	 * Set the V3 FIFO such that writes have higher priority than
+	 * reads, and local bus write causes local bus read fifo flush
+	 * on aperture 1. Same for PCI.
+	 */
+	writew(V3_FIFO_PRIO_LB_RD1_FLUSH_AP1 |
+	       V3_FIFO_PRIO_LB_RD0_FLUSH_AP1 |
+	       V3_FIFO_PRIO_PCI_RD1_FLUSH_AP1 |
+	       V3_FIFO_PRIO_PCI_RD0_FLUSH_AP1,
+	       v3->base + V3_FIFO_PRIORITY);
+
+
+	/*
+	 * Clear any error interrupts, and enable parity and write error
+	 * interrupts
+	 */
+	writeb(0, v3->base + V3_LB_ISTAT);
+	val = readw(v3->base + V3_LB_CFG);
+	val |= V3_LB_CFG_LB_LB_INT;
+	writew(val, v3->base + V3_LB_CFG);
+	writeb(V3_LB_ISTAT_PCI_WR | V3_LB_ISTAT_PCI_PERR,
+	       v3->base + V3_LB_IMASK);
+
+	/* Special Integrator initialization */
+	if (of_device_is_compatible(np, "arm,integrator-ap-pci")) {
+		ret = v3_integrator_init(v3);
+		if (ret)
+			return ret;
+	}
+
+	/* Post-init: enable PCI memory and invalidate (master already on) */
+	val = readw(v3->base + V3_PCI_CMD);
+	val |= PCI_COMMAND_MEMORY | PCI_COMMAND_INVALIDATE;
+	writew(val, v3->base + V3_PCI_CMD);
+
+	/* Clear pending interrupts */
+	writeb(0, v3->base + V3_LB_ISTAT);
+	/* Read or write errors and parity errors cause interrupts */
+	writeb(V3_LB_ISTAT_PCI_RD | V3_LB_ISTAT_PCI_WR | V3_LB_ISTAT_PCI_PERR,
+	       v3->base + V3_LB_IMASK);
+
+	/* Take the PCI bus out of reset so devices can initialize */
+	val = readw(v3->base + V3_SYSTEM);
+	val |= V3_SYSTEM_M_RST_OUT;
+	writew(val, v3->base + V3_SYSTEM);
+
+	/*
+	 * Re-lock the system register.
+	 */
+	val = readw(v3->base + V3_SYSTEM);
+	val |= V3_SYSTEM_M_LOCK;
+	writew(val, v3->base + V3_SYSTEM);
+
+	list_splice_init(&res, &host->windows);
+	ret = pci_scan_root_bus_bridge(host);
+	if (ret) {
+		dev_err(dev, "failed to register host: %d\n", ret);
+		return ret;
+	}
+	v3->bus = host->bus;
+
+	pci_bus_assign_resources(v3->bus);
+	pci_bus_add_devices(v3->bus);
+
+	return 0;
+}
+
+static const struct of_device_id v3_pci_of_match[] = {
+	{
+		.compatible = "v3,v360epc-pci",
+	},
+	{},
+};
+
+static struct platform_driver v3_pci_driver = {
+	.driver = {
+		.name = "pci-v3-semi",
+		.of_match_table = of_match_ptr(v3_pci_of_match),
+		.suppress_bind_attrs = true,
+	},
+	.probe  = v3_pci_probe,
+};
+builtin_platform_driver(v3_pci_driver);