From 331de00a64e5027365145bdf51da27b9ce15dfd5 Mon Sep 17 00:00:00 2001 From: Sergio Aguirre Date: Thu, 4 Apr 2013 10:32:13 -0700 Subject: xhci-mem: init list heads at the beginning of init It is possible that we fail on xhci_mem_init, just before doing the INIT_LIST_HEAD, and calling xhci_mem_cleanup. Problem is that, the list_for_each_entry_safe macro, assumes list heads are initialized (not NULL), and dereferences their 'next' pointer, causing a kernel panic if this is not yet initialized. Let's protect from that by moving inits to the beginning. This patch should be backported to kernels as old as 3.2, that contain the commit 9574323c39d1f8359a04843075d89c9f32d8b7e6 "xHCI: test USB2 software LPM". Signed-off-by: Sergio Aguirre Acked-by: David Cohen Signed-off-by: Sarah Sharp Cc: stable@vger.kernel.org --- drivers/usb/host/xhci-mem.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 2cfc465925bd..bda2c51a7c74 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -2256,6 +2256,9 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) u32 page_size, temp; int i; + INIT_LIST_HEAD(&xhci->lpm_failed_devs); + INIT_LIST_HEAD(&xhci->cancel_cmd_list); + page_size = xhci_readl(xhci, &xhci->op_regs->page_size); xhci_dbg(xhci, "Supported page size register = 0x%x\n", page_size); for (i = 0; i < 16; i++) { @@ -2334,7 +2337,6 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) xhci->cmd_ring = xhci_ring_alloc(xhci, 1, 1, TYPE_COMMAND, flags); if (!xhci->cmd_ring) goto fail; - INIT_LIST_HEAD(&xhci->cancel_cmd_list); xhci_dbg(xhci, "Allocated command ring at %p\n", xhci->cmd_ring); xhci_dbg(xhci, "First segment DMA is 0x%llx\n", (unsigned long long)xhci->cmd_ring->first_seg->dma); @@ -2445,8 +2447,6 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) if (xhci_setup_port_arrays(xhci, flags)) goto fail; - INIT_LIST_HEAD(&xhci->lpm_failed_devs); - /* Enable USB 3.0 device notifications for function remote wake, which * is necessary for allowing USB 3.0 devices to do remote wakeup from * U3 (device suspend). -- cgit v1.2.3 From 88696ae432ce7321540ac53d9caab3de9118b094 Mon Sep 17 00:00:00 2001 From: Vladimir Murzin Date: Tue, 9 Apr 2013 22:33:31 +0400 Subject: xhci: fix list access before init If for whatever reason we fall into fail path in xhci_mem_init() before bw table gets initialized we may access the uninitialized lists in xhci_mem_cleanup(). Check for bw table before traversing lists in cleanup routine. This patch should be backported to kernels as old as 3.2, that contain the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store information about roothubs and TTs." Reported-by: Sergey Dyasly Tested-by: Sergey Dyasly Signed-off-by: Vladimir Murzin Signed-off-by: Sarah Sharp Cc: stable@vger.kernel.org --- drivers/usb/host/xhci-mem.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index bda2c51a7c74..fbf75e57628b 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1827,6 +1827,9 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) } spin_unlock_irqrestore(&xhci->lock, flags); + if (!xhci->rh_bw) + goto no_bw; + num_ports = HCS_MAX_PORTS(xhci->hcs_params1); for (i = 0; i < num_ports; i++) { struct xhci_interval_bw_table *bwt = &xhci->rh_bw[i].bw_table; @@ -1845,6 +1848,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) } } +no_bw: xhci->num_usb2_ports = 0; xhci->num_usb3_ports = 0; xhci->num_active_eps = 0; -- cgit v1.2.3 From 77df9e0b799b03e1d5d9c68062709af5f637e834 Mon Sep 17 00:00:00 2001 From: Tony Camuso Date: Thu, 21 Feb 2013 16:11:27 -0500 Subject: xhci - correct comp_mode_recovery_timer on return from hibernate Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware) was a workaround for systems using the SN65LVPE502CP, controller, but it introduced a bug in resume from hibernate. The fix created a timer, comp_mode_recovery_timer, which is deleted from a timer list when xhci_suspend() is called. However, the hibernate image, including the timer list containing the comp_mode_recovery_timer, had already been saved before the timer was deleted. Upon resume from hibernate, the list containing the comp_mode_recovery_timer is restored from the image saved to disk, and xhci_resume(), assuming that the timer had been deleted by xhci_suspend(), makes a call to compliance_mode_recoery_timer_init(), which creates a new instance of the comp_mode_recovery_timer and attempts to place it into the same list in which it is already active, thus corrupting the list during the list_add() call. At this point, a call trace is emitted indicating the list corruption. Soon afterward, the system locks up, the watchdog times out, and the ensuing NMI crashes the system. The problem did not occur when resuming from suspend. In suspend, the image in RAM remains exactly as it was when xhci_suspend() deleted the comp_mode_recovery_timer, so there is no problem when xhci_resume() creates a new instance of this timer and places it in the still empty list. This patch avoids the problem by deleting the timer in xhci_resume() when resuming from hibernate. Now xhci_resume() can safely make the call to create a new instance of this timer, whether returning from suspend or hibernate. Thanks to Alan Stern for his help with understanding the problem. [Sarah reworked this patch to cover the case where the xHCI restore register operation fails, and (temp & STS_SRE) is true (and we re-init the host, including re-init for the compliance mode), but hibernate is false. The original patch would have caused list corruption in this case.] This patch should be backported to kernels as old as 3.2, that contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware" Signed-off-by: Tony Camuso Tested-by: Tony Camuso Acked-by: Don Zickus Signed-off-by: Sarah Sharp Cc: stable@vger.kernel.org --- drivers/usb/host/xhci.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index b4aa79d154b2..ae59119ed087 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -956,6 +956,7 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) struct usb_hcd *hcd = xhci_to_hcd(xhci); struct usb_hcd *secondary_hcd; int retval = 0; + bool comp_timer_running = false; /* Wait a bit if either of the roothubs need to settle from the * transition into bus suspend. @@ -993,6 +994,13 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) /* If restore operation fails, re-initialize the HC during resume */ if ((temp & STS_SRE) || hibernated) { + + if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && + !(xhci_all_ports_seen_u0(xhci))) { + del_timer_sync(&xhci->comp_mode_recovery_timer); + xhci_dbg(xhci, "Compliance Mode Recovery Timer deleted!\n"); + } + /* Let the USB core know _both_ roothubs lost power. */ usb_root_hub_lost_power(xhci->main_hcd->self.root_hub); usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub); @@ -1035,6 +1043,8 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) retval = xhci_init(hcd->primary_hcd); if (retval) return retval; + comp_timer_running = true; + xhci_dbg(xhci, "Start the primary HCD\n"); retval = xhci_run(hcd->primary_hcd); if (!retval) { @@ -1076,7 +1086,7 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) * to suffer the Compliance Mode issue again. It doesn't matter if * ports have entered previously to U0 before system's suspension. */ - if (xhci->quirks & XHCI_COMP_MODE_QUIRK) + if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && !comp_timer_running) compliance_mode_recovery_timer_init(xhci); /* Re-enable port polling. */ -- cgit v1.2.3 From c3897aa5386faba77e5bbdf94902a1658d3a5b11 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Thu, 18 Apr 2013 10:02:03 -0700 Subject: xhci: Disable D3cold for buggy TI redrivers. Some xHCI hosts contain a "redriver" from TI that silently drops port status connect changes if the port slips into Compliance Mode. If the port slips into compliance mode while the host is in D0, there will not be a port status change event. If the port slips into compliance mode while the host is in D3, the host will not send a PME. This includes when the system is suspended (S3) or hibernated (S4). If this happens when the system is in S3/S4, there is nothing software can do. Other port status change events that would normally cause the host to wake the system from S3/S4 may also be lost. This includes remote wakeup, disconnects and connects on other ports, and overrcurrent events. A decision was made to _NOT_ disable system suspend/hibernate on these systems, since users are unlikely to enable wakeup from S3/S4 for the xHCI host. Software can deal with this issue when the system is in S0. A work around was put in to poll the port status registers for Compliance Mode. The xHCI driver will continue to poll the registers while the host is runtime suspended. Unfortunately, that means we can't allow the PCI device to go into D3cold, because power will be removed from the host, and the config space will read as all Fs. Disable D3cold in the xHCI PCI runtime suspend function. This patch should be backported to kernels as old as 3.2, that contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware" Signed-off-by: Sarah Sharp Cc: Huang Ying Cc: stable@vger.kernel.org --- drivers/usb/host/xhci-pci.c | 8 ++++++++ drivers/usb/host/xhci.c | 4 ++-- drivers/usb/host/xhci.h | 3 +++ 3 files changed, 13 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 1a30c380043c..cc24e39b97d5 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -221,6 +221,14 @@ static void xhci_pci_remove(struct pci_dev *dev) static int xhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + + /* + * Systems with the TI redriver that loses port status change events + * need to have the registers polled during D3, so avoid D3cold. + */ + if (xhci_compliance_mode_recovery_timer_quirk_check()) + pdev->no_d3cold = true; return xhci_suspend(xhci); } diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index ae59119ed087..d8f640b12dd9 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -466,7 +466,7 @@ static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci) * Systems: * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820 */ -static bool compliance_mode_recovery_timer_quirk_check(void) +bool xhci_compliance_mode_recovery_timer_quirk_check(void) { const char *dmi_product_name, *dmi_sys_vendor; @@ -517,7 +517,7 @@ int xhci_init(struct usb_hcd *hcd) xhci_dbg(xhci, "Finished xhci_init\n"); /* Initializing Compliance Mode Recovery Data If Needed */ - if (compliance_mode_recovery_timer_quirk_check()) { + if (xhci_compliance_mode_recovery_timer_quirk_check()) { xhci->quirks |= XHCI_COMP_MODE_QUIRK; compliance_mode_recovery_timer_init(xhci); } diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 29c978e37135..77600cefcaf1 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1853,4 +1853,7 @@ struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index); +/* xHCI quirks */ +bool xhci_compliance_mode_recovery_timer_quirk_check(void); + #endif /* __LINUX_XHCI_HCD_H */ -- cgit v1.2.3 From f28c42c576b293b3a1daaed8ca2775ebc2fe5398 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Fri, 24 May 2013 14:29:20 +0800 Subject: usb: dwc3: pci: PHY should be deleted later than dwc3 core If the glue layer is removed first (core layer later), it deletes the phy device first, then the core device. But at core's removal, it still uses PHY's resources, it may cause kernel's oops. It is much like the problem Paul Zimmerman reported at: http://marc.info/?l=linux-usb&m=136547502011472&w=2. Besides, it is reasonable the PHY is deleted at last as the controller is the PHY's user. Signed-off-by: Peter Chen Cc: Signed-off-by: Felipe Balbi --- drivers/usb/dwc3/dwc3-pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c index 227d4a7acad7..eba9e2baf32b 100644 --- a/drivers/usb/dwc3/dwc3-pci.c +++ b/drivers/usb/dwc3/dwc3-pci.c @@ -196,9 +196,9 @@ static void dwc3_pci_remove(struct pci_dev *pci) { struct dwc3_pci *glue = pci_get_drvdata(pci); + platform_device_unregister(glue->dwc3); platform_device_unregister(glue->usb2_phy); platform_device_unregister(glue->usb3_phy); - platform_device_unregister(glue->dwc3); pci_set_drvdata(pci, NULL); pci_disable_device(pci); } -- cgit v1.2.3 From 022d0547aa8b00ff5035ba6207ebc2c08ea0a51f Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Fri, 24 May 2013 14:30:16 +0800 Subject: usb: dwc3: exynos: PHY should be deleted later than dwc3 core If the glue layer is removed first (core layer later), it deletes the phy device first, then the core device. But at core's removal, it still uses PHY's resources, it may cause kernel's oops. It is much like the problem Paul Zimmerman reported at: http://marc.info/?l=linux-usb&m=136547502011472&w=2. Besides, it is reasonable the PHY is deleted at last as the controller is the PHY's user. Signed-off-by: Peter Chen Cc: Signed-off-by: Felipe Balbi --- drivers/usb/dwc3/dwc3-exynos.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/dwc3/dwc3-exynos.c b/drivers/usb/dwc3/dwc3-exynos.c index 929e7dd6e58b..8ce9d7fd6cfc 100644 --- a/drivers/usb/dwc3/dwc3-exynos.c +++ b/drivers/usb/dwc3/dwc3-exynos.c @@ -164,9 +164,9 @@ static int dwc3_exynos_remove(struct platform_device *pdev) { struct dwc3_exynos *exynos = platform_get_drvdata(pdev); + device_for_each_child(&pdev->dev, NULL, dwc3_exynos_remove_child); platform_device_unregister(exynos->usb2_phy); platform_device_unregister(exynos->usb3_phy); - device_for_each_child(&pdev->dev, NULL, dwc3_exynos_remove_child); clk_disable_unprepare(exynos->clk); -- cgit v1.2.3 From 5bf8fae33d14cc5c3c53a926f9079f92c8b082b0 Mon Sep 17 00:00:00 2001 From: George Cherian Date: Mon, 27 May 2013 14:35:49 +0530 Subject: usb: dwc3: gadget: free trb pool only from epnum 2 we never allocate a TRB pool for physical endpoints 0 and 1 so trying to free it (a invalid TRB pool pointer) will lead us in a warning while removing dwc3.ko module. In order to fix the situation, all we have to do is skip dwc3_free_trb_pool() for physical endpoints 0 and 1 just as we while deleting endpoints from the endpoints list. Cc: stable@vger.kernel.org Signed-off-by: George Cherian Signed-off-by: Felipe Balbi --- drivers/usb/dwc3/gadget.c | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 2b6e7e001207..b5e5b35df49c 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -1706,11 +1706,19 @@ static void dwc3_gadget_free_endpoints(struct dwc3 *dwc) dep = dwc->eps[epnum]; if (!dep) continue; - - dwc3_free_trb_pool(dep); - - if (epnum != 0 && epnum != 1) + /* + * Physical endpoints 0 and 1 are special; they form the + * bi-directional USB endpoint 0. + * + * For those two physical endpoints, we don't allocate a TRB + * pool nor do we add them the endpoints list. Due to that, we + * shouldn't do these two operations otherwise we would end up + * with all sorts of bugs when removing dwc3.ko. + */ + if (epnum != 0 && epnum != 1) { + dwc3_free_trb_pool(dep); list_del(&dep->endpoint.ep_list); + } kfree(dep); } -- cgit v1.2.3 From ed74df12dc3e07a37d99aab60211496e871488a0 Mon Sep 17 00:00:00 2001 From: Virupax Sadashivpetimath Date: Wed, 24 Apr 2013 08:38:48 +0200 Subject: usb: musb: make use_sg flag URB specific Since highmem PIO URB handling was introduced in: 8e8a551 usb: musb: host: Handle highmem in PIO mode when a URB is being handled it may happen that the static use_sg flag was set by a previous URB with buffer in highmem. This leads to error in handling the present URB. Fix this by making the use_sg flag URB specific. Cc: stable # 3.7+ Acked-by: Linus Walleij Signed-off-by: Virupax Sadashivpetimath Signed-off-by: Fabio Baltieri Signed-off-by: Felipe Balbi --- drivers/usb/musb/musb_host.c | 18 ++++++++---------- drivers/usb/musb/musb_host.h | 1 + 2 files changed, 9 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c index 8914dec49f01..9d3044bdebe5 100644 --- a/drivers/usb/musb/musb_host.c +++ b/drivers/usb/musb/musb_host.c @@ -1232,7 +1232,6 @@ void musb_host_tx(struct musb *musb, u8 epnum) void __iomem *mbase = musb->mregs; struct dma_channel *dma; bool transfer_pending = false; - static bool use_sg; musb_ep_select(mbase, epnum); tx_csr = musb_readw(epio, MUSB_TXCSR); @@ -1463,9 +1462,9 @@ done: * NULL. */ if (!urb->transfer_buffer) - use_sg = true; + qh->use_sg = true; - if (use_sg) { + if (qh->use_sg) { /* sg_miter_start is already done in musb_ep_program */ if (!sg_miter_next(&qh->sg_miter)) { dev_err(musb->controller, "error: sg list empty\n"); @@ -1484,9 +1483,9 @@ done: qh->segsize = length; - if (use_sg) { + if (qh->use_sg) { if (offset + length >= urb->transfer_buffer_length) - use_sg = false; + qh->use_sg = false; } musb_ep_select(mbase, epnum); @@ -1552,7 +1551,6 @@ void musb_host_rx(struct musb *musb, u8 epnum) bool done = false; u32 status; struct dma_channel *dma; - static bool use_sg; unsigned int sg_flags = SG_MITER_ATOMIC | SG_MITER_TO_SG; musb_ep_select(mbase, epnum); @@ -1878,12 +1876,12 @@ void musb_host_rx(struct musb *musb, u8 epnum) * NULL. */ if (!urb->transfer_buffer) { - use_sg = true; + qh->use_sg = true; sg_miter_start(&qh->sg_miter, urb->sg, 1, sg_flags); } - if (use_sg) { + if (qh->use_sg) { if (!sg_miter_next(&qh->sg_miter)) { dev_err(musb->controller, "error: sg list empty\n"); sg_miter_stop(&qh->sg_miter); @@ -1913,8 +1911,8 @@ finish: urb->actual_length += xfer_len; qh->offset += xfer_len; if (done) { - if (use_sg) - use_sg = false; + if (qh->use_sg) + qh->use_sg = false; if (urb->status == -EINPROGRESS) urb->status = status; diff --git a/drivers/usb/musb/musb_host.h b/drivers/usb/musb/musb_host.h index 5a9c8feec10c..738f7eb60df9 100644 --- a/drivers/usb/musb/musb_host.h +++ b/drivers/usb/musb/musb_host.h @@ -74,6 +74,7 @@ struct musb_qh { u16 frame; /* for periodic schedule */ unsigned iso_idx; /* in urb->iso_frame_desc[] */ struct sg_mapping_iter sg_miter; /* for highmem in PIO mode */ + bool use_sg; /* to track urb using sglist */ }; /* map from control or bulk queue head to the first qh on that ring */ -- cgit v1.2.3 From fdc03438f53a00294ed9939eb3a1f6db6f3d8963 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 28 May 2013 14:03:10 -0400 Subject: USB: revert periodic scheduling bugfix This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d (USB: EHCI: fix bug in scheduling periodic split transfers). The commit was valid -- it fixed a real bug -- but the periodic scheduler in ehci-hcd is in such bad shape (especially the part that handles split transactions) that fixing one bug is very likely to cause another to surface. That's what happened in this case; the result was choppy and noisy playback on certain 24-bit audio devices. The only real fix will be to rewrite this entire section of code. My next project... This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110. Thanks to Tim Richardson for extra testing and feedback, and to Joseph Salisbury and Tyson Tan for tracking down the original source of the problem. Signed-off-by: Alan Stern CC: Joseph Salisbury CC: Tim Richardson Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-sched.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index acff5b8f6e89..f3c1028a54fc 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -213,7 +213,7 @@ static inline unsigned char tt_start_uframe(struct ehci_hcd *ehci, __hc32 mask) } static const unsigned char -max_tt_usecs[] = { 125, 125, 125, 125, 125, 125, 125, 25 }; +max_tt_usecs[] = { 125, 125, 125, 125, 125, 125, 30, 0 }; /* carryover low/fullspeed bandwidth that crosses uframe boundries */ static inline void carryover_tt_bandwidth(unsigned short tt_usecs[8]) -- cgit v1.2.3 From 5f8e2c07d75967ee49a5da1d21ddf5f50d48cda0 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:37 +0200 Subject: USB: serial: fix Treo/Kyocera interrrupt-in urb context The first and second interrupt-in urbs are swapped for some Treo/Kyocera devices, but the urb context was never updated with the new port. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/visor.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c index 7573ec8a084f..8d1a3e63b0ad 100644 --- a/drivers/usb/serial/visor.c +++ b/drivers/usb/serial/visor.c @@ -564,6 +564,7 @@ static int treo_attach(struct usb_serial *serial) dest->bulk_in_endpointAddress = src->bulk_in_endpointAddress;\ dest->bulk_in_buffer = src->bulk_in_buffer; \ dest->interrupt_in_urb = src->interrupt_in_urb; \ + dest->interrupt_in_urb->context = dest; \ dest->interrupt_in_endpointAddress = \ src->interrupt_in_endpointAddress;\ dest->interrupt_in_buffer = src->interrupt_in_buffer; \ -- cgit v1.2.3 From 420021a395ce38b7ab2cceb52dee4038be7d8fa3 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:38 +0200 Subject: USB: visor: fix initialisation of Treo/Kyocera devices Fix regression introduced by commit 214916f2e ("USB: visor: reimplement using generic framework") which broke initialisation of Treo/Kyocera devices that re-mapped bulk-in endpoints. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/visor.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c index 8d1a3e63b0ad..9910aa2edf4b 100644 --- a/drivers/usb/serial/visor.c +++ b/drivers/usb/serial/visor.c @@ -560,9 +560,17 @@ static int treo_attach(struct usb_serial *serial) */ #define COPY_PORT(dest, src) \ do { \ + int i; \ + \ + for (i = 0; i < ARRAY_SIZE(src->read_urbs); ++i) { \ + dest->read_urbs[i] = src->read_urbs[i]; \ + dest->read_urbs[i]->context = dest; \ + dest->bulk_in_buffers[i] = src->bulk_in_buffers[i]; \ + } \ dest->read_urb = src->read_urb; \ dest->bulk_in_endpointAddress = src->bulk_in_endpointAddress;\ dest->bulk_in_buffer = src->bulk_in_buffer; \ + dest->bulk_in_size = src->bulk_in_size; \ dest->interrupt_in_urb = src->interrupt_in_urb; \ dest->interrupt_in_urb->context = dest; \ dest->interrupt_in_endpointAddress = \ -- cgit v1.2.3 From 72ea18a558ed7a63a50bb121ba60d73b5b38ae30 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:39 +0200 Subject: USB: mos7720: fix DMA to stack The read_mos_reg function is called with stack-allocated buffers, which must not be used for control messages. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7720.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index cc0e54345df9..7752cffbf2bc 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -227,11 +227,22 @@ static int read_mos_reg(struct usb_serial *serial, unsigned int serial_portnum, __u8 requesttype = (__u8)0xc0; __u16 index = get_reg_index(reg); __u16 value = get_reg_value(reg, serial_portnum); - int status = usb_control_msg(usbdev, pipe, request, requesttype, value, - index, data, 1, MOS_WDR_TIMEOUT); - if (status < 0) + u8 *buf; + int status; + + buf = kmalloc(1, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + status = usb_control_msg(usbdev, pipe, request, requesttype, value, + index, buf, 1, MOS_WDR_TIMEOUT); + if (status == 1) + *data = *buf; + else if (status < 0) dev_err(&usbdev->dev, "mos7720: usb_control_msg() failed: %d", status); + kfree(buf); + return status; } -- cgit v1.2.3 From 15ee89c3347fbf58a4361011eda5ac2731e45126 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:40 +0200 Subject: USB: mos7840: fix DMA to stack Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840: add support for MCS7810 devices") which used stack-allocated buffers for control messages. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7840.c | 35 +++++++++++++++++++++++++++-------- 1 file changed, 27 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index a0d5ea545982..7e998081e1cd 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -2142,13 +2142,21 @@ static int mos7840_ioctl(struct tty_struct *tty, static int mos7810_check(struct usb_serial *serial) { int i, pass_count = 0; + u8 *buf; __u16 data = 0, mcr_data = 0; __u16 test_pattern = 0x55AA; + int res; + + buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL); + if (!buf) + return 0; /* failed to identify 7810 */ /* Store MCR setting */ - usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER, - &mcr_data, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + if (res == VENDOR_READ_LENGTH) + mcr_data = *buf; for (i = 0; i < 16; i++) { /* Send the 1-bit test pattern out to MCS7810 test pin */ @@ -2158,9 +2166,12 @@ static int mos7810_check(struct usb_serial *serial) MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT); /* Read the test pattern back */ - usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data, - VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + res = usb_control_msg(serial->dev, + usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ, + MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, + VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + if (res == VENDOR_READ_LENGTH) + data = *buf; /* If this is a MCS7810 device, both test patterns must match */ if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001) @@ -2174,6 +2185,8 @@ static int mos7810_check(struct usb_serial *serial) MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT); + kfree(buf); + if (pass_count == 16) return 1; @@ -2183,11 +2196,17 @@ static int mos7810_check(struct usb_serial *serial) static int mos7840_calc_num_ports(struct usb_serial *serial) { __u16 data = 0x00; + u8 *buf; int mos7840_num_ports; - usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &data, - VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL); + if (buf) { + usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), + MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, + VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); + data = *buf; + kfree(buf); + } if (serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7810 || serial->dev->descriptor.idProduct == MOSCHIP_DEVICE_ID_7820) { -- cgit v1.2.3 From 634371911730a462626071065b64cd6e1fe213e0 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:41 +0200 Subject: USB: ark3116: fix control-message timeout The control-message timeout is specified in milliseconds and should not depend on HZ. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ark3116.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c index 3b16118cbf62..40e7fd94646f 100644 --- a/drivers/usb/serial/ark3116.c +++ b/drivers/usb/serial/ark3116.c @@ -43,7 +43,7 @@ #define DRIVER_NAME "ark3116" /* usb timeout of 1 second */ -#define ARK_TIMEOUT (1*HZ) +#define ARK_TIMEOUT 1000 static const struct usb_device_id id_table[] = { { USB_DEVICE(0x6547, 0x0232) }, -- cgit v1.2.3 From 6c13ff68a7ce01da7a51b44241a7aad8eaaedde7 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:42 +0200 Subject: USB: iuu_phoenix: fix bulk-message timeout The bulk-message timeout is specified in milliseconds and should not depend on HZ. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/iuu_phoenix.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c index 9d74c278b7b5..790673e5faa7 100644 --- a/drivers/usb/serial/iuu_phoenix.c +++ b/drivers/usb/serial/iuu_phoenix.c @@ -287,7 +287,7 @@ static int bulk_immediate(struct usb_serial_port *port, u8 *buf, u8 count) usb_bulk_msg(serial->dev, usb_sndbulkpipe(serial->dev, port->bulk_out_endpointAddress), buf, - count, &actual, HZ * 1); + count, &actual, 1000); if (status != IUU_OPERATION_OK) dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status); @@ -307,7 +307,7 @@ static int read_immediate(struct usb_serial_port *port, u8 *buf, u8 count) usb_bulk_msg(serial->dev, usb_rcvbulkpipe(serial->dev, port->bulk_in_endpointAddress), buf, - count, &actual, HZ * 1); + count, &actual, 1000); if (status != IUU_OPERATION_OK) dev_dbg(&port->dev, "%s - error = %2x\n", __func__, status); -- cgit v1.2.3 From 849513a7809175420d353625b6f651d961e99d49 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:43 +0200 Subject: USB: mos7720: fix message timeouts The control and bulk-message timeouts are specified in milliseconds and should not depend on HZ. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7720.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index 7752cffbf2bc..6eac26649009 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -40,7 +40,7 @@ #define DRIVER_DESC "Moschip USB Serial Driver" /* default urb timeout */ -#define MOS_WDR_TIMEOUT (HZ * 5) +#define MOS_WDR_TIMEOUT 5000 #define MOS_MAX_PORT 0x02 #define MOS_WRITE 0x0E @@ -1938,7 +1938,7 @@ static int mos7720_startup(struct usb_serial *serial) /* setting configuration feature to one */ usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), - (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5*HZ); + (__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5000); /* start the interrupt urb */ ret_val = usb_submit_urb(serial->port[0]->interrupt_in_urb, GFP_KERNEL); @@ -1981,7 +1981,7 @@ static void mos7720_release(struct usb_serial *serial) /* wait for synchronous usb calls to return */ if (mos_parport->msg_pending) wait_for_completion_timeout(&mos_parport->syncmsg_compl, - MOS_WDR_TIMEOUT); + msecs_to_jiffies(MOS_WDR_TIMEOUT)); parport_remove_port(mos_parport->pp); usb_set_serial_data(serial, NULL); -- cgit v1.2.3 From 5cbfa3acdcbf19e1d29cf3479ad8200d2e644e44 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 May 2013 14:44:44 +0200 Subject: USB: zte_ev: fix control-message timeouts The control-message timeout is specified in milliseconds and should not depend on HZ. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/zte_ev.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/zte_ev.c b/drivers/usb/serial/zte_ev.c index 39ee7373b4ee..b9a88f253636 100644 --- a/drivers/usb/serial/zte_ev.c +++ b/drivers/usb/serial/zte_ev.c @@ -53,7 +53,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0001, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 2st cmd and recieve data */ @@ -65,7 +65,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 3 cmd */ @@ -84,7 +84,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 4 cmd */ @@ -95,7 +95,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 5 cmd */ @@ -107,7 +107,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 6 cmd */ @@ -126,7 +126,7 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); kfree(buf); @@ -178,7 +178,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0002, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 2st ctl cmd(CTL 21 22 03 00 00 00 00 00 ) */ @@ -186,7 +186,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 3st cmd and recieve data */ @@ -198,7 +198,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 4 cmd */ @@ -217,7 +217,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 5 cmd */ @@ -228,7 +228,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); /* send 6 cmd */ @@ -240,7 +240,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), 0x21, 0xa1, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 7 cmd */ @@ -259,7 +259,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x20, 0x21, 0x0000, 0x0000, buf, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); debug_data(dev, __func__, len, buf, result); /* send 8 cmd */ @@ -270,7 +270,7 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) result = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), 0x22, 0x21, 0x0003, 0x0000, NULL, len, - HZ * USB_CTRL_GET_TIMEOUT); + USB_CTRL_GET_TIMEOUT); dev_dbg(dev, "result = %d\n", result); kfree(buf); -- cgit v1.2.3 From e2e2f0ea1c935edcf53feb4c4c8fdb4f86d57dd9 Mon Sep 17 00:00:00 2001 From: Federico Manzan Date: Fri, 24 May 2013 18:18:48 +0200 Subject: usbfs: Increase arbitrary limit for USB 3 isopkt length Increase the current arbitrary limit for isocronous packet size to a value large enough to account for USB 3.0 super bandwidth streams, bMaxBurst (0~15 allowed, 1~16 packets) bmAttributes (bit 1:0, mult 0~2, 1~3 packets) so the size max for one USB 3 isocronous transfer is 1024 byte * 16 * 3 = 49152 byte Acked-by: Alan Stern Signed-off-by: Federico Manzan Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index caefc800f298..c88c4fb9459d 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -1287,9 +1287,13 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb, goto error; } for (totlen = u = 0; u < uurb->number_of_packets; u++) { - /* arbitrary limit, - * sufficient for USB 2.0 high-bandwidth iso */ - if (isopkt[u].length > 8192) { + /* + * arbitrary limit need for USB 3.0 + * bMaxBurst (0~15 allowed, 1~16 packets) + * bmAttributes (bit 1:0, mult 0~2, 1~3 packets) + * sizemax: 1024 * 16 * 3 = 49152 + */ + if (isopkt[u].length > 49152) { ret = -EINVAL; goto error; } -- cgit v1.2.3 From 077f5f1c23b3cf1134c031677497dfb6077e6bdd Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Wed, 29 May 2013 11:33:52 -0400 Subject: USB: EHCI: fix regression related to qh_refresh() This patch adds some code that inadvertently got left out of commit c1fdb68e3d73741630ca16695cf9176c233be7ed (USB: EHCI: changes related to qh_refresh()). The calls to qh_refresh() and qh_link_periodic() were taken out of qh_schedule(); therefore it is necessary to call these routines manually after calling qh_schedule(). Signed-off-by: Alan Stern Reported-and-tested-by: Oleksij Rempel Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-sched.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index f3c1028a54fc..f80d0330d548 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -646,6 +646,10 @@ static void end_unlink_intr(struct ehci_hcd *ehci, struct ehci_qh *qh) /* reschedule QH iff another request is queued */ if (!list_empty(&qh->qtd_list) && ehci->rh_state == EHCI_RH_RUNNING) { rc = qh_schedule(ehci, qh); + if (rc == 0) { + qh_refresh(ehci, qh); + qh_link_periodic(ehci, qh); + } /* An error here likely indicates handshake failure * or no space left in the schedule. Neither fault @@ -653,9 +657,10 @@ static void end_unlink_intr(struct ehci_hcd *ehci, struct ehci_qh *qh) * * FIXME kill the now-dysfunctional queued urbs */ - if (rc != 0) + else { ehci_err(ehci, "can't reschedule qh %p, err %d\n", qh, rc); + } } /* maybe turn off periodic schedule */ -- cgit v1.2.3 From 6529591e3eef65f0f528a81ac169f6e294b947a7 Mon Sep 17 00:00:00 2001 From: Robert Butora Date: Fri, 31 May 2013 18:09:51 +0300 Subject: USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device The patch adds a new HIDCOM device and does not affect other devices driven by the cypress_M8 module. Changes are: - add VendorID ProductID to device tables - skip unstable speed check because FRWD uses 115200bps - skip reset at probe which is an issue workaround for this particular device. Signed-off-by: Robert Butora Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cypress_m8.c | 18 +++++++++++++++++- drivers/usb/serial/cypress_m8.h | 4 ++++ 2 files changed, 21 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index d341555d37d8..082120198f87 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -65,6 +65,7 @@ static const struct usb_device_id id_table_earthmate[] = { static const struct usb_device_id id_table_cyphidcomrs232[] = { { USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) }, { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) }, + { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) }, { } /* Terminating entry */ }; @@ -78,6 +79,7 @@ static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(VENDOR_ID_DELORME, PRODUCT_ID_EARTHMATEUSB_LT20) }, { USB_DEVICE(VENDOR_ID_CYPRESS, PRODUCT_ID_CYPHIDCOM) }, { USB_DEVICE(VENDOR_ID_POWERCOM, PRODUCT_ID_UPS) }, + { USB_DEVICE(VENDOR_ID_FRWD, PRODUCT_ID_CYPHIDCOM_FRWD) }, { USB_DEVICE(VENDOR_ID_DAZZLE, PRODUCT_ID_CA42) }, { } /* Terminating entry */ }; @@ -229,6 +231,12 @@ static struct usb_serial_driver * const serial_drivers[] = { * Cypress serial helper functions *****************************************************************************/ +/* FRWD Dongle hidcom needs to skip reset and speed checks */ +static inline bool is_frwd(struct usb_device *dev) +{ + return ((le16_to_cpu(dev->descriptor.idVendor) == VENDOR_ID_FRWD) && + (le16_to_cpu(dev->descriptor.idProduct) == PRODUCT_ID_CYPHIDCOM_FRWD)); +} static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate) { @@ -238,6 +246,10 @@ static int analyze_baud_rate(struct usb_serial_port *port, speed_t new_rate) if (unstable_bauds) return new_rate; + /* FRWD Dongle uses 115200 bps */ + if (is_frwd(port->serial->dev)) + return new_rate; + /* * The general purpose firmware for the Cypress M8 allows for * a maximum speed of 57600bps (I have no idea whether DeLorme @@ -448,7 +460,11 @@ static int cypress_generic_port_probe(struct usb_serial_port *port) return -ENOMEM; } - usb_reset_configuration(serial->dev); + /* Skip reset for FRWD device. It is a workaound: + device hangs if it receives SET_CONFIGURE in Configured + state. */ + if (!is_frwd(serial->dev)) + usb_reset_configuration(serial->dev); priv->cmd_ctrl = 0; priv->line_control = 0; diff --git a/drivers/usb/serial/cypress_m8.h b/drivers/usb/serial/cypress_m8.h index 67cf60826884..b461311a2ae7 100644 --- a/drivers/usb/serial/cypress_m8.h +++ b/drivers/usb/serial/cypress_m8.h @@ -24,6 +24,10 @@ #define VENDOR_ID_CYPRESS 0x04b4 #define PRODUCT_ID_CYPHIDCOM 0x5500 +/* FRWD Dongle - a GPS sports watch */ +#define VENDOR_ID_FRWD 0x6737 +#define PRODUCT_ID_CYPHIDCOM_FRWD 0x0001 + /* Powercom UPS, chip CY7C63723 */ #define VENDOR_ID_POWERCOM 0x0d9f #define PRODUCT_ID_UPS 0x0002 -- cgit v1.2.3 From 8a2f132a01c2dd4c3905fa560f92019761ed72b1 Mon Sep 17 00:00:00 2001 From: Richard Weinberger Date: Fri, 24 May 2013 12:01:51 +0200 Subject: USB: serial: Add Option GTM681W to qcserial device table. The Option GTM681W uses a qualcomm chip and can be served by the qcserial device driver. Signed-off-by: Richard Weinberger Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/qcserial.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/usb/serial/qcserial.c b/drivers/usb/serial/qcserial.c index 59b32b782126..bd794b43898c 100644 --- a/drivers/usb/serial/qcserial.c +++ b/drivers/usb/serial/qcserial.c @@ -118,6 +118,7 @@ static const struct usb_device_id id_table[] = { {USB_DEVICE(0x1199, 0x901b)}, /* Sierra Wireless MC7770 */ {USB_DEVICE(0x12D1, 0x14F0)}, /* Sony Gobi 3000 QDL */ {USB_DEVICE(0x12D1, 0x14F1)}, /* Sony Gobi 3000 Composite */ + {USB_DEVICE(0x0AF0, 0x8120)}, /* Option GTM681W */ /* non Gobi Qualcomm serial devices */ {USB_DEVICE_INTERFACE_NUMBER(0x0f3d, 0x68a2, 0)}, /* Sierra Wireless MC7700 Device Management */ -- cgit v1.2.3 From d8a1d0d54d5fdac0347b75e9afd554b3dfaa465f Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Tue, 4 Jun 2013 18:50:28 +0200 Subject: USB: zte_ev: fix broken open Remove bogus port-number check in open and close, which prevented this driver from being used with a minor number different from zero. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/zte_ev.c | 6 ------ 1 file changed, 6 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/zte_ev.c b/drivers/usb/serial/zte_ev.c index b9a88f253636..870e01e24481 100644 --- a/drivers/usb/serial/zte_ev.c +++ b/drivers/usb/serial/zte_ev.c @@ -41,9 +41,6 @@ static int zte_ev_usb_serial_open(struct tty_struct *tty, int len; unsigned char *buf; - if (port->number != 0) - return -ENODEV; - buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL); if (!buf) return -ENOMEM; @@ -166,9 +163,6 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) int len; unsigned char *buf; - if (port->number != 0) - return; - buf = kmalloc(MAX_SETUP_DATA_SIZE, GFP_KERNEL); if (!buf) return; -- cgit v1.2.3 From a07088098a650267b2eda689538133a324b9523f Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Tue, 4 Jun 2013 18:50:29 +0200 Subject: USB: keyspan: fix bogus array index The outcont_endpoints array was indexed using the port minor number (which can be greater than the array size) rather than the device port number. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/keyspan.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c index eb30d7b01f36..d85a3e037490 100644 --- a/drivers/usb/serial/keyspan.c +++ b/drivers/usb/serial/keyspan.c @@ -1559,7 +1559,7 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, d_details = s_priv->device_details; device_port = port->number - port->serial->minor; - outcont_urb = d_details->outcont_endpoints[port->number]; + outcont_urb = d_details->outcont_endpoints[device_port]; this_urb = p_priv->outcont_urb; dev_dbg(&port->dev, "%s - endpoint %d\n", __func__, usb_pipeendpoint(this_urb->pipe)); -- cgit v1.2.3 From c1ec1bcf0c97cdd4e25f16524c962fae9a4a39f9 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Tue, 4 Jun 2013 18:50:30 +0200 Subject: USB: keyspan: remove unused endpoint-array access Remove the no longer used endpoint-array access completely. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/keyspan.c | 10 ---------- 1 file changed, 10 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c index d85a3e037490..3549d073df22 100644 --- a/drivers/usb/serial/keyspan.c +++ b/drivers/usb/serial/keyspan.c @@ -1548,7 +1548,6 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, struct keyspan_serial_private *s_priv; struct keyspan_port_private *p_priv; const struct keyspan_device_details *d_details; - int outcont_urb; struct urb *this_urb; int device_port, err; @@ -1559,7 +1558,6 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, d_details = s_priv->device_details; device_port = port->number - port->serial->minor; - outcont_urb = d_details->outcont_endpoints[device_port]; this_urb = p_priv->outcont_urb; dev_dbg(&port->dev, "%s - endpoint %d\n", __func__, usb_pipeendpoint(this_urb->pipe)); @@ -1685,14 +1683,6 @@ static int keyspan_usa26_send_setup(struct usb_serial *serial, err = usb_submit_urb(this_urb, GFP_ATOMIC); if (err != 0) dev_dbg(&port->dev, "%s - usb_submit_urb(setup) failed (%d)\n", __func__, err); -#if 0 - else { - dev_dbg(&port->dev, "%s - usb_submit_urb(%d) OK %d bytes (end %d)\n", __func__ - outcont_urb, this_urb->transfer_buffer_length, - usb_pipeendpoint(this_urb->pipe)); - } -#endif - return 0; } -- cgit v1.2.3 From a26f009a070e840fadacb91013b2391ba7ab6cc2 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Tue, 4 Jun 2013 18:50:31 +0200 Subject: USB: mos7720: fix hardware flow control The register access to enable hardware flow control depends on the device port number and not the port minor number. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7720.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index 6eac26649009..f27c621a9297 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -1629,7 +1629,7 @@ static void change_port_settings(struct tty_struct *tty, mos7720_port->shadowMCR |= (UART_MCR_XONANY); /* To set hardware flow control to the specified * * serial port, in SP1/2_CONTROL_REG */ - if (port->number) + if (port_number) write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x01); else write_mos_reg(serial, dummy, SP_CONTROL_REG, 0x02); -- cgit v1.2.3 From f4488035abdac56682153aa0cff3d1dce84e1c54 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 5 Jun 2013 12:21:11 +0200 Subject: USB: serial: fix TIOCMIWAIT return value Fix regression introduced by commit 143d9d9616 ("USB: serial: add tiocmiwait subdriver operation") which made the ioctl operation return ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT implementation is missing. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/usb-serial.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 4753c005cfb6..5f6b1ff9d29e 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -408,7 +408,7 @@ static int serial_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) { struct usb_serial_port *port = tty->driver_data; - int retval = -ENODEV; + int retval = -ENOIOCTLCMD; dev_dbg(tty->dev, "%s - cmd 0x%.4x\n", __func__, cmd); @@ -420,8 +420,6 @@ static int serial_ioctl(struct tty_struct *tty, default: if (port->serial->type->ioctl) retval = port->serial->type->ioctl(tty, cmd, arg); - else - retval = -ENOIOCTLCMD; } return retval; -- cgit v1.2.3 From 9eecf22d2b375b9064a20421c6c307b760b03d46 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Thu, 6 Jun 2013 13:32:47 +0200 Subject: USB: whiteheat: fix broken port configuration When configuring the port (e.g. set_termios) the port minor number rather than the port number was used in the request (and they only coincide for minor number 0). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/whiteheat.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c index b9fca3586d74..347caad47a12 100644 --- a/drivers/usb/serial/whiteheat.c +++ b/drivers/usb/serial/whiteheat.c @@ -649,7 +649,7 @@ static void firm_setup_port(struct tty_struct *tty) struct whiteheat_port_settings port_settings; unsigned int cflag = tty->termios.c_cflag; - port_settings.port = port->number + 1; + port_settings.port = port->number - port->serial->minor + 1; /* get the byte size */ switch (cflag & CSIZE) { -- cgit v1.2.3 From b8a24e6281d37243c06b9497dcbfaa98c1e2ad35 Mon Sep 17 00:00:00 2001 From: Bjørn Mork Date: Thu, 6 Jun 2013 12:57:24 +0200 Subject: USB: option: blacklist network interface on Huawei E1820 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The mode used by Windows for the Huawei E1820 will use the same ff/ff/ff class codes for both serial and network functions. Reported-by: Graham Inggs Signed-off-by: Bjørn Mork Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 93d02bc4eb52..66314c3b6d1a 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -593,6 +593,8 @@ static const struct usb_device_id option_ids[] = { .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, + { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0x14ac, 0xff, 0xff, 0xff), /* Huawei E1820 */ + .driver_info = (kernel_ulong_t) &net_intf1_blacklist }, { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4605, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t) &huawei_cdc12_blacklist }, { USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, 0xff, 0xff, 0xff) }, -- cgit v1.2.3 From 73228a0538a70ebc4547bd09dee8971360dc1d87 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 5 Jun 2013 15:26:27 -0500 Subject: USB: option,zte_ev: move most ZTE CDMA devices to zte_ev Per some ZTE Linux drivers I found for the AC2716, the following patch moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff that option does is not required with zte_ev, because it doesn't implement any of the send_setup hooks which the blacklist suppressed. I did not move the 2718 over because I could not find any ZTE Linux drivers for that device, nor even any Windows drivers. Signed-off-by: Dan Williams Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 24 +----------------------- drivers/usb/serial/zte_ev.c | 24 +++++++++++++++++++++--- 2 files changed, 22 insertions(+), 26 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 66314c3b6d1a..bd4323ddae1a 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -250,13 +250,7 @@ static void option_instat_callback(struct urb *urb); #define ZTE_PRODUCT_MF622 0x0001 #define ZTE_PRODUCT_MF628 0x0015 #define ZTE_PRODUCT_MF626 0x0031 -#define ZTE_PRODUCT_CDMA_TECH 0xfffe -#define ZTE_PRODUCT_AC8710 0xfff1 -#define ZTE_PRODUCT_AC2726 0xfff5 -#define ZTE_PRODUCT_AC8710T 0xffff #define ZTE_PRODUCT_MC2718 0xffe8 -#define ZTE_PRODUCT_AD3812 0xffeb -#define ZTE_PRODUCT_MC2716 0xffed #define BENQ_VENDOR_ID 0x04a5 #define BENQ_PRODUCT_H10 0x4068 @@ -495,18 +489,10 @@ static const struct option_blacklist_info zte_k3765_z_blacklist = { .reserved = BIT(4), }; -static const struct option_blacklist_info zte_ad3812_z_blacklist = { - .sendsetup = BIT(0) | BIT(1) | BIT(2), -}; - static const struct option_blacklist_info zte_mc2718_z_blacklist = { .sendsetup = BIT(1) | BIT(2) | BIT(3) | BIT(4), }; -static const struct option_blacklist_info zte_mc2716_z_blacklist = { - .sendsetup = BIT(1) | BIT(2) | BIT(3), -}; - static const struct option_blacklist_info huawei_cdc12_blacklist = { .reserved = BIT(1) | BIT(2), }; @@ -799,7 +785,6 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_1012, 0xff) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC650) }, { USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) }, - { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */ { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6280) }, /* BP3-USB & BP3-EXT HSDPA */ @@ -1201,16 +1186,9 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0178, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&net_intf3_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC2726, 0xff, 0xff, 0xff) }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710T, 0xff, 0xff, 0xff) }, + /* NOTE: most ZTE CDMA devices should be driven by zte_ev, not option */ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2718, 0xff, 0xff, 0xff), .driver_info = (kernel_ulong_t)&zte_mc2718_z_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AD3812, 0xff, 0xff, 0xff), - .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist }, - { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff), - .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) }, { USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) }, diff --git a/drivers/usb/serial/zte_ev.c b/drivers/usb/serial/zte_ev.c index 870e01e24481..fca4c752a4ed 100644 --- a/drivers/usb/serial/zte_ev.c +++ b/drivers/usb/serial/zte_ev.c @@ -273,11 +273,29 @@ static void zte_ev_usb_serial_close(struct usb_serial_port *port) } static const struct usb_device_id id_table[] = { - { USB_DEVICE(0x19d2, 0xffff) }, /* AC8700 */ - { USB_DEVICE(0x19d2, 0xfffe) }, - { USB_DEVICE(0x19d2, 0xfffd) }, /* MG880 */ + /* AC8710, AC8710T */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffff, 0xff, 0xff, 0xff) }, + /* AC8700 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfffe, 0xff, 0xff, 0xff) }, + /* MG880 */ + { USB_DEVICE(0x19d2, 0xfffd) }, + { USB_DEVICE(0x19d2, 0xfffc) }, + { USB_DEVICE(0x19d2, 0xfffb) }, + /* AC2726, AC8710_V3 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xfff1, 0xff, 0xff, 0xff) }, + { USB_DEVICE(0x19d2, 0xfff6) }, + { USB_DEVICE(0x19d2, 0xfff7) }, + { USB_DEVICE(0x19d2, 0xfff8) }, + { USB_DEVICE(0x19d2, 0xfff9) }, + { USB_DEVICE(0x19d2, 0xffee) }, + /* AC2716, MC2716 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffed, 0xff, 0xff, 0xff) }, + /* AD3812 */ + { USB_DEVICE_AND_INTERFACE_INFO(0x19d2, 0xffeb, 0xff, 0xff, 0xff) }, + { USB_DEVICE(0x19d2, 0xffec) }, { USB_DEVICE(0x05C6, 0x3197) }, { USB_DEVICE(0x05C6, 0x6000) }, + { USB_DEVICE(0x05C6, 0x9008) }, { }, }; MODULE_DEVICE_TABLE(usb, id_table); -- cgit v1.2.3