From 3d35ac346e981162eeba391e496faceed4753e7b Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Mon, 14 Feb 2011 18:36:03 -0800 Subject: x86, reboot: Move the real-mode reboot code to an assembly file Move the real-mode reboot code out to an assembly file (reboot_32.S) which is allocated using the common lowmem trampoline allocator. Signed-off-by: H. Peter Anvin LKML-Reference: <4D5DFBE4.7090104@intel.com> Cc: Stephen Rothwell Cc: Rafael J. Wysocki Cc: Matthieu Castet --- arch/x86/kernel/reboot_32.S | 131 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 131 insertions(+) create mode 100644 arch/x86/kernel/reboot_32.S (limited to 'arch/x86/kernel/reboot_32.S') diff --git a/arch/x86/kernel/reboot_32.S b/arch/x86/kernel/reboot_32.S new file mode 100644 index 000000000000..f242356a096e --- /dev/null +++ b/arch/x86/kernel/reboot_32.S @@ -0,0 +1,131 @@ +#include +#include +#include +#include + +/* + * The following code and data reboots the machine by switching to real + * mode and jumping to the BIOS reset entry point, as if the CPU has + * really been reset. The previous version asked the keyboard + * controller to pulse the CPU reset line, which is more thorough, but + * doesn't work with at least one type of 486 motherboard. It is easy + * to stop this code working; hence the copious comments. + * + * This code is called with the restart type (0 = BIOS, 1 = APM) in %eax. + */ + .section ".x86_trampoline","a" + .balign 16 + .code32 +ENTRY(machine_real_restart_asm) +r_base = . + /* Get our own relocated address */ + call 1f +1: popl %ebx + subl $1b, %ebx + + /* Patch post-real-mode segment jump */ + movw dispatch_table(%ebx,%ecx,2),%cx + movw %cx, 101f(%ebx) + movw %ax, 102f(%ebx) + + /* Set up the IDT for real mode. */ + lidtl machine_real_restart_idt(%ebx) + + /* + * Set up a GDT from which we can load segment descriptors for real + * mode. The GDT is not used in real mode; it is just needed here to + * prepare the descriptors. + */ + lgdtl machine_real_restart_gdt(%ebx) + + /* + * Load the data segment registers with 16-bit compatible values + */ + movl $16, %ecx + movl %ecx, %ds + movl %ecx, %es + movl %ecx, %fs + movl %ecx, %gs + movl %ecx, %ss + ljmpl $8, $1f - r_base + +/* + * This is 16-bit protected mode code to disable paging and the cache, + * switch to real mode and jump to the BIOS reset code. + * + * The instruction that switches to real mode by writing to CR0 must be + * followed immediately by a far jump instruction, which set CS to a + * valid value for real mode, and flushes the prefetch queue to avoid + * running instructions that have already been decoded in protected + * mode. + * + * Clears all the flags except ET, especially PG (paging), PE + * (protected-mode enable) and TS (task switch for coprocessor state + * save). Flushes the TLB after paging has been disabled. Sets CD and + * NW, to disable the cache on a 486, and invalidates the cache. This + * is more like the state of a 486 after reset. I don't know if + * something else should be done for other chips. + * + * More could be done here to set up the registers as if a CPU reset had + * occurred; hopefully real BIOSs don't assume much. This is not the + * actual BIOS entry point, anyway (that is at 0xfffffff0). + * + * Most of this work is probably excessive, but it is what is tested. + */ + .code16 +1: + xorl %ecx, %ecx + movl %cr0, %eax + andl $0x00000011, %eax + orl $0x60000000, %eax + movl %eax, %cr0 + movl %ecx, %cr3 + movl %cr0, %edx + andl $0x60000000, %edx /* If no cache bits -> no wbinvd */ + jz 2f + wbinvd +2: + andb $0x10, %al + movl %eax, %cr0 + .byte 0xea /* ljmpw */ +101: .word 0 /* Offset */ +102: .word 0 /* Segment */ + +bios: + ljmpw $0xf000, $0xfff0 + +apm: + movw $0x1000, %ax + movw %ax, %ss + movw $0xf000, %sp + movw $0x5307, %ax + movw $0x0001, %bx + movw $0x0003, %cx + int $0x15 + +END(machine_real_restart_asm) + + .balign 16 + /* These must match