From 88c23c05ef18f543fad7b26c95a3acc0ffb378cc Mon Sep 17 00:00:00 2001 From: Jelle van der Waa Date: Tue, 23 Jan 2018 15:58:44 -0800 Subject: ARM: dts: nanopi-neo-air: Add WiFi / eMMC Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air. This patch was originally submitted by Jelle van der Waa. Martin Kelly modified it to compile on the latest kernel, fixed up some review comments from Maxime Ripard, and re-tested the patch. Cc: Maxime Ripard Cc: linux-sunxi@googlegroups.com Cc: devicetree@vger.kernel.org Signed-off-by: Jelle van der Waa Signed-off-by: Martin Kelly Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 03ff6f8b93ff..920849092cc8 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -72,6 +72,11 @@ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ }; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; }; &mmc0 { @@ -84,6 +89,25 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- cgit v1.2.3 From 45e01f401a2a16a8d7ca910fe01c124451980bd8 Mon Sep 17 00:00:00 2001 From: Tuomas Tynkkynen Date: Fri, 22 Dec 2017 22:57:37 +0200 Subject: ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property Using the cd-inverted property is not useful when GPIOs are used as card detects since the polarity can be specified with the usual GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for U-Boot developers, so migrate all sunxi boards away from cd-inverted. Signed-off-by: Tuomas Tynkkynen Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun4i-a10-a1000.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-gemei-g9.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-hackberry.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-inet1.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-inet97fv2.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-marsboard.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-mini-xplus.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-mk802.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-mk802ii.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-pcduino.dts | 3 +-- arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts | 3 +-- arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts | 3 +-- arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts | 3 +-- arch/arm/boot/dts/sun5i-a10s-mk802.dts | 3 +-- arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 6 ++---- arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts | 3 +-- arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts | 3 +-- arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts | 3 +-- arch/arm/boot/dts/sun5i-a13-hsg-h702.dts | 3 +-- arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts | 3 +-- arch/arm/boot/dts/sun5i-a13-olinuxino.dts | 3 +-- arch/arm/boot/dts/sun5i-gr8-evb.dts | 3 +-- arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi | 3 +-- arch/arm/boot/dts/sun6i-a31-colombus.dts | 3 +-- arch/arm/boot/dts/sun6i-a31-hummingbird.dts | 3 +-- arch/arm/boot/dts/sun6i-a31-i7.dts | 3 +-- arch/arm/boot/dts/sun6i-a31-m9.dts | 3 +-- arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts | 3 +-- arch/arm/boot/dts/sun6i-a31s-primo81.dts | 3 +-- arch/arm/boot/dts/sun6i-a31s-sina31s.dts | 3 +-- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 3 +-- arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts | 3 +-- arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi | 3 +-- arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-bananapi.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-bananapro.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-hummingbird.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-icnova-swac.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-itead-ibox.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-m3.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-mk808c.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts | 6 ++---- arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 6 ++---- arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts | 6 ++---- arch/arm/boot/dts/sun7i-a20-orangepi.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-pcduino3.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 3 +-- arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts | 3 +-- arch/arm/boot/dts/sun8i-a23-evb.dts | 3 +-- arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 3 +-- arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts | 3 +-- arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts | 3 +-- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 3 +-- arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 3 +-- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 3 +-- arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 3 +-- arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 3 +-- arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 3 +-- arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 3 +-- arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi | 3 +-- arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 3 +-- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 3 +-- arch/arm/boot/dts/sun9i-a80-optimus.dts | 3 +-- 86 files changed, 90 insertions(+), 180 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts index 09e909576c61..6c254ec4c85b 100644 --- a/arch/arm/boot/dts/sun4i-a10-a1000.dts +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts @@ -164,8 +164,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts index 39ba4ccb9e2e..38a2c4134952 100644 --- a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts +++ b/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts @@ -106,8 +106,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts index dfc88aee4fe3..cf7b392dff31 100644 --- a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts +++ b/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts @@ -123,8 +123,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts index 1982c8c238c5..197a1f2b75ff 100644 --- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts @@ -162,8 +162,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts b/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts index 147cbc5e08ac..896e27a08727 100644 --- a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts +++ b/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts @@ -150,8 +150,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts index 41ca8bded89f..ea7a59dcf8f9 100644 --- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts +++ b/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts @@ -141,8 +141,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH01 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-hackberry.dts b/arch/arm/boot/dts/sun4i-a10-hackberry.dts index f33e42d6ce8b..cc988ccd5ca7 100644 --- a/arch/arm/boot/dts/sun4i-a10-hackberry.dts +++ b/arch/arm/boot/dts/sun4i-a10-hackberry.dts @@ -106,8 +106,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts b/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts index 35c57d065dd8..f63767cddd8e 100644 --- a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts +++ b/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts @@ -78,8 +78,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts index 9482e831a9a1..26d0c1d6a02b 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet1.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -152,8 +152,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts index 4b5c91c8e85b..5d096528e75a 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts @@ -142,8 +142,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts index 13224f5ac166..221acd10f6c8 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts @@ -300,8 +300,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts index d22bd79562d8..80ecd78247ac 100644 --- a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts +++ b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts @@ -106,8 +106,7 @@ pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts index 879141ca6027..247fa27ef717 100644 --- a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts +++ b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts @@ -133,8 +133,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-marsboard.dts b/arch/arm/boot/dts/sun4i-a10-marsboard.dts index 435c551aef0f..0dbf69576512 100644 --- a/arch/arm/boot/dts/sun4i-a10-marsboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-marsboard.dts @@ -132,8 +132,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts b/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts index 1b639e5f9172..f9d74e21031d 100644 --- a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts +++ b/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts @@ -96,8 +96,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-mk802.dts b/arch/arm/boot/dts/sun4i-a10-mk802.dts index 7198b34e2e50..face1925ee5b 100644 --- a/arch/arm/boot/dts/sun4i-a10-mk802.dts +++ b/arch/arm/boot/dts/sun4i-a10-mk802.dts @@ -73,8 +73,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts b/arch/arm/boot/dts/sun4i-a10-mk802ii.dts index e460da2eb139..17dcdf031118 100644 --- a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts +++ b/arch/arm/boot/dts/sun4i-a10-mk802ii.dts @@ -82,8 +82,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts index 49247fbe6acd..f15f01955fdf 100644 --- a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts @@ -165,8 +165,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts index 6e140547b638..b97a0f2f20b9 100644 --- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts +++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts @@ -140,8 +140,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts index 5081303f79e7..84b25be1ac94 100644 --- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -138,8 +138,7 @@ &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts index d2dee8d434bf..39504d720efc 100644 --- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts @@ -93,8 +93,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - cd-inverted; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts index 16f839df4227..8d4fb9331212 100644 --- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts @@ -104,8 +104,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - cd-inverted; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-mk802.dts b/arch/arm/boot/dts/sun5i-a10s-mk802.dts index 020aa9d6c31d..dd7fd5c3d76f 100644 --- a/arch/arm/boot/dts/sun5i-a10s-mk802.dts +++ b/arch/arm/boot/dts/sun5i-a10s-mk802.dts @@ -92,8 +92,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - cd-inverted; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts index da95118af4dc..2c902ed2c87a 100644 --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts @@ -201,8 +201,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - cd-inverted; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */ status = "okay"; }; @@ -211,8 +210,7 @@ pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ - cd-inverted; + cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts index 262b3669f04d..034853d1c08f 100644 --- a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts +++ b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts @@ -80,8 +80,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ - cd-inverted; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts index 5482be174e12..3f68ef5d92a0 100644 --- a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts +++ b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts @@ -130,8 +130,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ - cd-inverted; + cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts index 3dbb0d7c2f8c..378214d8316e 100644 --- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts +++ b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts @@ -125,8 +125,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts index 584fa579ded2..7ee0c3f6d7a1 100644 --- a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts +++ b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts @@ -120,8 +120,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts index 3a831eaf1dfc..aa4b34fd9126 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts @@ -99,8 +99,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts index 4b9af423c6d5..437ad913a373 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts @@ -194,8 +194,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-gr8-evb.dts b/arch/arm/boot/dts/sun5i-gr8-evb.dts index 558c16a30543..5f0adc0f7bb4 100644 --- a/arch/arm/boot/dts/sun5i-gr8-evb.dts +++ b/arch/arm/boot/dts/sun5i-gr8-evb.dts @@ -236,8 +236,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gr8_evb>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi index 49229b3d5492..8acbaab14fe5 100644 --- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi @@ -127,8 +127,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */ - cd-inverted; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/sun6i-a31-colombus.dts index 85eff0307ca4..939c497a6f70 100644 --- a/arch/arm/boot/dts/sun6i-a31-colombus.dts +++ b/arch/arm/boot/dts/sun6i-a31-colombus.dts @@ -117,8 +117,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts index 19e382a11297..ce4f9e9834bf 100644 --- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts +++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts @@ -218,8 +218,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-i7.dts b/arch/arm/boot/dts/sun6i-a31-i7.dts index 010a84c7c012..2e0a672c8031 100644 --- a/arch/arm/boot/dts/sun6i-a31-i7.dts +++ b/arch/arm/boot/dts/sun6i-a31-i7.dts @@ -124,8 +124,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_i7>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ - cd-inverted; + cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts index 50605fd4449e..9698f6d38d03 100644 --- a/arch/arm/boot/dts/sun6i-a31-m9.dts +++ b/arch/arm/boot/dts/sun6i-a31-m9.dts @@ -107,8 +107,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ - cd-inverted; + cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts index 5219556e9f73..bb14b171b160 100644 --- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts +++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts @@ -107,8 +107,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ - cd-inverted; + cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts index 0cdb38ab3377..4cb9664cdb29 100644 --- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -151,8 +151,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts b/arch/arm/boot/dts/sun6i-a31s-sina31s.dts index 298476485bb4..da0ccf5a2c44 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s.dts @@ -167,8 +167,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina31s>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */ - cd-inverted; + cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts index 51e6f1d21c32..3077e8ec9cd9 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -120,8 +120,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m2>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 0 4 GPIO_ACTIVE_HIGH>; /* PA4 */ - cd-inverted; + cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts index f3edf9ca435c..aab6c1720ef7 100644 --- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts @@ -102,8 +102,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bs1078v2>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi index 3cc4046b904a..4e72e4f3ef96 100644 --- a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi @@ -69,8 +69,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */ - cd-inverted; + cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts index 4ed3162e3e5a..763cb03033c4 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts @@ -184,8 +184,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m1p>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index 88a1c2363c6c..6f744f8931f0 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -159,8 +159,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts index e7af1b7c33d5..0898eb6162f5 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts @@ -158,8 +158,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index 39f43e4eb742..942ac9dfd4a5 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -165,8 +165,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts index 8c9bedc602ec..5649161de1d7 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -206,8 +206,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts index 6e6264cd69f8..1f0e5ecbf0c4 100644 --- a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts +++ b/arch/arm/boot/dts/sun7i-a20-hummingbird.dts @@ -163,8 +163,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts index 55809973a568..2e3f2f29d124 100644 --- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts +++ b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts @@ -160,8 +160,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts b/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts index 794e7617f545..926fa194eb1b 100644 --- a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts +++ b/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts @@ -107,8 +107,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 8 5 GPIO_ACTIVE_HIGH>; /* PI5 */ - cd-inverted; + cd-gpios = <&pio 8 5 GPIO_ACTIVE_LOW>; /* PI5 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts index 8a8a6dbcd414..1b05ba466e7d 100644 --- a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts +++ b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts @@ -124,8 +124,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts b/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts index 442f3c755f36..b1ab7c1c33e3 100644 --- a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts +++ b/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts @@ -227,8 +227,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_lamobo_r1>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-m3.dts b/arch/arm/boot/dts/sun7i-a20-m3.dts index 43c94787ef07..e91a209850bc 100644 --- a/arch/arm/boot/dts/sun7i-a20-m3.dts +++ b/arch/arm/boot/dts/sun7i-a20-m3.dts @@ -120,8 +120,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-mk808c.dts b/arch/arm/boot/dts/sun7i-a20-mk808c.dts index f7413094183c..ce3f09aaeed2 100644 --- a/arch/arm/boot/dts/sun7i-a20-mk808c.dts +++ b/arch/arm/boot/dts/sun7i-a20-mk808c.dts @@ -112,8 +112,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts index 64c8ef9a2756..8f34731dee34 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -190,8 +190,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; @@ -200,8 +199,7 @@ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olimex_som_evb>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */ - cd-inverted; + cd-gpios = <&pio 7 0 GPIO_ACTIVE_LOW>; /* PH0 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts index edf9c3c6c0d7..d20fd03596e9 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts @@ -158,8 +158,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts index ba250189d07f..b828677f331d 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts @@ -159,8 +159,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index dffbaa24b3ee..866d230593be 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -226,8 +226,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; @@ -236,8 +235,7 @@ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ - cd-inverted; + cd-gpios = <&pio 7 11 GPIO_ACTIVE_LOW>; /* PH11 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts index 7af4c8fc1865..a5ae0c55bf5b 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts @@ -144,8 +144,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; @@ -154,8 +153,7 @@ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_orangepi>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ - cd-inverted; + cd-gpios = <&pio 7 11 GPIO_ACTIVE_LOW>; /* PH11 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi.dts b/arch/arm/boot/dts/sun7i-a20-orangepi.dts index 0a8d4a05e8a0..7a4244e57589 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi.dts @@ -135,8 +135,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ - cd-inverted; + cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts index fb591f32252c..bfca960b03e0 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts @@ -158,8 +158,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts index 777152a3df0f..c576f101fbde 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts @@ -159,8 +159,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index f8d0aafb9f88..8202c87ca6a3 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -154,8 +154,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts index 7f8405a0dd0f..ff5c1086585c 100644 --- a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts +++ b/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts @@ -123,8 +123,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ - cd-inverted; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a23-evb.dts b/arch/arm/boot/dts/sun8i-a23-evb.dts index 87289a60c520..8a93697df3a5 100644 --- a/arch/arm/boot/dts/sun8i-a23-evb.dts +++ b/arch/arm/boot/dts/sun8i-a23-evb.dts @@ -107,8 +107,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_evb>; vmmc-supply = <®_vcc3v0>; bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts index be9a6b8d7a1e..9757265c58d4 100644 --- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts @@ -81,8 +81,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts index 433cf2a2a9a2..541acb4d2b91 100644 --- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts @@ -144,8 +144,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts index 5091cecbcd1e..36ecebaff3c0 100644 --- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts +++ b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts @@ -87,9 +87,8 @@ pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ bus-width = <4>; - cd-inverted; status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts index 6550bf0e594b..1890d41b7fae 100644 --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts @@ -112,8 +112,7 @@ pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts index 6da08cd0e107..88decb0747ac 100644 --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts @@ -176,8 +176,7 @@ pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index 6713d0f2b3f4..9a5017bb1440 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -116,8 +116,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index f1c3f1cc4d97..3a196a86a984 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -140,8 +140,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 10da56e86ab8..7824f0dbf022 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -119,8 +119,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index d406571a0dd6..d9dc14fe2aa3 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -154,8 +154,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc_io>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 920849092cc8..48563adc7430 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -84,8 +84,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi index 7646e331bd29..e9af61394f5d 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi +++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi @@ -95,8 +95,7 @@ &mmc0 { bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; status = "okay"; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index b20be95b49d5..629f76b85005 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -136,8 +136,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts index a70a1daf4e2c..398f975b380d 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -110,8 +110,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 82e5d28cd698..40941fef4ff3 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -110,8 +110,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index d22546df1b82..c4769def8cd6 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -132,8 +132,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - cd-inverted; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts index eaf09666720d..0dbdb29a8fff 100644 --- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts +++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts @@ -150,8 +150,7 @@ pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts index 8c5efe2a9881..27d9ccd0ef2f 100644 --- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -164,8 +164,7 @@ &mmc0 { vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ - cd-inverted; + cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index d6bd15898db6..f51f37cc721d 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -85,8 +85,7 @@ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ - cd-inverted; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts index fe16fc0eb518..a26d72c3f9b5 100644 --- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts +++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts @@ -150,8 +150,7 @@ &mmc0 { vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ - cd-inverted; + cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 4024639aa005..31b06ecbc306 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -88,8 +88,7 @@ pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */ - cd-inverted; + cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH18 */ status = "okay"; }; diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts index a9b807be99a0..58a199b0e494 100644 --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts @@ -125,8 +125,7 @@ pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; bus-width = <4>; - cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */ - cd-inverted; + cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH8 */ status = "okay"; }; -- cgit v1.2.3 From 8b8061fcbfaecd4b15deb01819ddd2cb3c4d40c6 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 8 Feb 2018 18:06:13 +0800 Subject: ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form factor and GPIO holes similar to Raspberry Pi Zero. It features: - Allwinner H2+ SoC - Single-chip (16-bit) 512MiB DDR3 DRAM - Ampak AP6212 Wi-Fi/Bluetooth module - MicroSD slot - Two MicroUSB Type-B ports (one can only be used to power the board and the other features OTG functionality) - Two keys, a reset and a GPIO-connected key. - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+. - CSI connector to connect the camera sensor provided by Sinovoip. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 125 +++++++++++++++++++++ 2 files changed, 126 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ade7a38543dc..d5a17e6e8b0f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-a83t-tbs-a711.dtb \ sun8i-h2-plus-orangepi-r1.dtb \ + sun8i-h2-plus-bananapi-m2-zero.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ sun8i-h3-beelink-x2.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts new file mode 100644 index 000000000000..1cdbd9a3ef57 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -0,0 +1,125 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Icenowy Zheng + * + * Based on sun8i-h3-bananapi-m2-plus.dts, which is: + * Copyright (C) 2016 Chen-Yu Tsai + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include + +/ { + model = "Banana Pi BPI-M2-Zero"; + compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + + pwr_led { + label = "bananapi-m2-zero:red:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ + default-state = "on"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + + sw4 { + label = "power"; + linux,code = ; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; +}; + +&ehci0 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + /* + * On the production batch of this board the card detect GPIO is + * high active (card inserted), although on the early samples it's + * low active. + */ + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + vqmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + /* + * There're two micro-USB connectors, one is power-only and another is + * OTG. The Vbus of these two connectors are connected together, so + * the external USB device will be powered just by the power input + * from the power-only USB port. + */ + status = "okay"; +}; -- cgit v1.2.3 From f8d5fe8fc31ad96f5d67a8c5250b101bb83116c4 Mon Sep 17 00:00:00 2001 From: Joonas Kylmälä Date: Thu, 8 Feb 2018 14:01:38 +0200 Subject: ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The GPIO card detection pin (mmc0_cd_pin) is already requested and configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c so pinctrl is not needed. Signed-off-by: Joonas Kylmälä Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 2 +- arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 2 +- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 2 +- arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 2 +- arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 2 +- arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 2 +- arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 2 +- arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 2 +- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 6 ------ 9 files changed, 8 insertions(+), 14 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index 3a196a86a984..781270fb79c3 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -137,7 +137,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 7824f0dbf022..20bbe2d712d0 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -116,7 +116,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 48563adc7430..1e2aa6bc7a7f 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -81,7 +81,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi index e9af61394f5d..32bf624dc59d 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi +++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi @@ -97,7 +97,7 @@ bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; status = "okay"; vmmc-supply = <®_vcc3v3>; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index 629f76b85005..99bce9822cad 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -133,7 +133,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts index 398f975b380d..df444056001a 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -107,7 +107,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 40941fef4ff3..4a4236b13220 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -107,7 +107,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index c4769def8cd6..583aae37694d 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -129,7 +129,7 @@ &mmc0 { pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 7a83b15225c7..6521d0f6a282 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -356,12 +356,6 @@ bias-pull-up; }; - mmc0_cd_pin: mmc0_cd_pin { - pins = "PF6"; - function = "gpio_in"; - bias-pull-up; - }; - mmc1_pins_a: mmc1 { pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; -- cgit v1.2.3 From 50caa75681357737b6c44b7c212964217ffc00de Mon Sep 17 00:00:00 2001 From: Joonas Kylmälä Date: Thu, 8 Feb 2018 14:01:39 +0200 Subject: ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Most of the boards use the mmc0 pins and their attributes defined in mmc0_pins_a. Let's default to those by moving the pinctrl attributes to the dtsi file. This makes it easier to modify device trees in the future as there is only one place to change the pinctrl attributes. Signed-off-by: Joonas Kylmälä Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 2 -- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 2 -- arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 2 -- arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 2 -- arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts | 2 -- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 2 -- arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 2 -- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 ++ arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts | 2 -- 17 files changed, 2 insertions(+), 32 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index 1cdbd9a3ef57..29a85eb14927 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -60,8 +60,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; /* diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index 9a5017bb1440..f3b066ff63cb 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -112,8 +112,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index 781270fb79c3..bea49ed89cc7 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -136,8 +136,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 20bbe2d712d0..9fc07593e907 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -115,8 +115,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index d9dc14fe2aa3..d0d41eb86cb4 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -150,8 +150,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc_io>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 1e2aa6bc7a7f..07e2e6180792 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -80,8 +80,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi index 32bf624dc59d..f110ee382239 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi +++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi @@ -96,8 +96,6 @@ &mmc0 { bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; status = "okay"; vmmc-supply = <®_vcc3v3>; }; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index 99bce9822cad..ac6f52f3fa62 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -132,8 +132,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts index df444056001a..82ab5b6b730b 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -106,8 +106,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index 4a4236b13220..c1a8cd93c463 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -106,8 +106,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index 583aae37694d..537227b85935 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -128,8 +128,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 6521d0f6a282..3a0854a96a04 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -141,6 +141,8 @@ mmc0: mmc@1c0f000 { /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c0f000 0x1000>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>; resets = <&ccu RST_BUS_MMC0>; reset-names = "ahb"; interrupts = ; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts index 1ed9f219deaf..1ef70cb4c9bc 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts @@ -151,8 +151,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts index f1447003ea3c..cc268a69786c 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts @@ -126,8 +126,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index 9e51d3a5f4e6..58505fbc2667 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -160,8 +160,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts index 0f25c4a6f15d..586ec67f4101 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts @@ -167,8 +167,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts index af43533c7134..feee125a4e9a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts @@ -74,8 +74,6 @@ }; &mmc0 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; -- cgit v1.2.3 From e607b605be46a44f50e3b48597188477e52eeff8 Mon Sep 17 00:00:00 2001 From: Joonas Kylmälä Date: Thu, 8 Feb 2018 14:01:40 +0200 Subject: ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Most of the boards use the mmc1 pins and their attributes defined in mmc1_pins_a. Let's default to that by moving the pinctrl attributes to the dtsi file. This makes it easier to modify device trees in the future as there is only one place to change the pinctrl attributes. Signed-off-by: Joonas Kylmälä Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 2 -- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 2 -- arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 2 -- arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 2 -- arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 2 -- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 2 -- arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts | 2 -- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 ++ arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 2 -- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts | 2 -- 13 files changed, 2 insertions(+), 24 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index 29a85eb14927..7d01f9322658 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -72,8 +72,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index f3b066ff63cb..73978853bb4c 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -119,8 +119,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc_wifi>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index bea49ed89cc7..9c1bc472fb1c 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -143,8 +143,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 9fc07593e907..870aabcbb2d8 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -122,8 +122,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; non-removable; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts index a6e61915d648..07b51a2f14c6 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts @@ -101,8 +101,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 07e2e6180792..6246d3eff39d 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -87,8 +87,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index ac6f52f3fa62..7569bd05e249 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -139,8 +139,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts index 82ab5b6b730b..2e59fd296717 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -113,8 +113,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; non-removable; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts index a10281b455f5..71fb73208939 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts @@ -59,8 +59,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; bus-width = <4>; non-removable; diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 3a0854a96a04..b4a4b3cb6c4e 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -154,6 +154,8 @@ mmc1: mmc@1c10000 { /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c10000 0x1000>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = ; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts index 1ef70cb4c9bc..506e25ba028a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts @@ -158,8 +158,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts index 586ec67f4101..803566608ed8 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts @@ -174,8 +174,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts index feee125a4e9a..eda24d813282 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts @@ -81,8 +81,6 @@ }; &mmc1 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; vmmc-supply = <®_vcc3v3>; vqmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; -- cgit v1.2.3 From 8566df712b5bb7b35d292f3b6b9216f511607e1f Mon Sep 17 00:00:00 2001 From: Joonas Kylmälä Date: Thu, 8 Feb 2018 14:01:41 +0200 Subject: ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit There is only one pinctrl configuration for mmc0 and mmc1 so let's drop the _a suffix from both of them. Signed-off-by: Joonas Kylmälä Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 2 +- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 8 ++++---- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index 73978853bb4c..f868cf197c8e 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -134,7 +134,7 @@ }; }; -&mmc1_pins_a { +&mmc1_pins { bias-pull-up; }; diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index b4a4b3cb6c4e..7741166d34d8 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -142,7 +142,7 @@ /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c0f000 0x1000>; pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins_a>; + pinctrl-0 = <&mmc0_pins>; resets = <&ccu RST_BUS_MMC0>; reset-names = "ahb"; interrupts = ; @@ -155,7 +155,7 @@ /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c10000 0x1000>; pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins_a>; + pinctrl-0 = <&mmc1_pins>; resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = ; @@ -352,7 +352,7 @@ function = "i2c2"; }; - mmc0_pins_a: mmc0 { + mmc0_pins: mmc0 { pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; function = "mmc0"; @@ -360,7 +360,7 @@ bias-pull-up; }; - mmc1_pins_a: mmc1 { + mmc1_pins: mmc1 { pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; function = "mmc1"; -- cgit v1.2.3 From 5f49ddb1a7bc265fdade9317842da7e7a9a6bcac Mon Sep 17 00:00:00 2001 From: Joonas Kylmälä Date: Mon, 12 Feb 2018 18:29:45 +0200 Subject: ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The mmc1_pins node with bias-pull-up attribute is already defined in the sunxi-h3-h5.dtsi file. Thus, we can remove it from here. Signed-off-by: Joonas Kylmälä Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 4 ---- 1 file changed, 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index f868cf197c8e..0bc031fe4c56 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -134,10 +134,6 @@ }; }; -&mmc1_pins { - bias-pull-up; -}; - &ohci0 { status = "okay"; }; -- cgit v1.2.3 From cb34d8256e0155f12b1c55b198d392a10131493f Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Thu, 1 Mar 2018 22:34:40 +0100 Subject: ARM: dts: sunxi: h3/h5: Add HDMI pipeline This commit adds all entries needed for HDMI to function properly. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 108 +++++++++++++++++++++++++++++++++++++ 1 file changed, 108 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 7741166d34d8..1be1a02d6df2 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -105,6 +105,12 @@ }; }; + de: display-engine { + compatible = "allwinner,sun8i-h3-display-engine"; + allwinner,pipelines = <&mixer0>; + status = "disabled"; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; @@ -123,6 +129,29 @@ #reset-cells = <1>; }; + mixer0: mixer@1100000 { + compatible = "allwinner,sun8i-h3-de2-mixer-0"; + reg = <0x01100000 0x100000>; + clocks = <&display_clocks CLK_BUS_MIXER0>, + <&display_clocks CLK_MIXER0>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_MIXER0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer0_out: port@1 { + reg = <1>; + + mixer0_out_tcon0: endpoint { + remote-endpoint = <&tcon0_in_mixer0>; + }; + }; + }; + }; + syscon: syscon@1c00000 { compatible = "allwinner,sun8i-h3-system-controller", "syscon"; @@ -138,6 +167,41 @@ #dma-cells = <1>; }; + tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun8i-h3-tcon-tv", + "allwinner,sun8i-a83t-tcon-tv"; + reg = <0x01c0c000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>; + clock-names = "ahb", "tcon-ch1"; + resets = <&ccu RST_BUS_TCON0>; + reset-names = "lcd"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + reg = <0>; + + tcon0_in_mixer0: endpoint { + remote-endpoint = <&mixer0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon0_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint = <&hdmi_in_tcon0>; + }; + }; + }; + }; + mmc0: mmc@1c0f000 { /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c0f000 0x1000>; @@ -682,6 +746,50 @@ interrupts = ; }; + hdmi: hdmi@1ee0000 { + compatible = "allwinner,sun8i-h3-dw-hdmi", + "allwinner,sun8i-a83t-dw-hdmi"; + reg = <0x01ee0000 0x10000>; + reg-io-width = <1>; + interrupts = ; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>, + <&ccu CLK_HDMI>; + clock-names = "iahb", "isfr", "tmds"; + resets = <&ccu RST_BUS_HDMI1>; + reset-names = "ctrl"; + phys = <&hdmi_phy>; + phy-names = "hdmi-phy"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + hdmi_in: port@0 { + reg = <0>; + + hdmi_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_hdmi>; + }; + }; + + hdmi_out: port@1 { + reg = <1>; + }; + }; + }; + + hdmi_phy: hdmi-phy@1ef0000 { + compatible = "allwinner,sun8i-h3-hdmi-phy"; + reg = <0x01ef0000 0x10000>; + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>, + <&ccu 6>; + clock-names = "bus", "mod", "pll-0"; + resets = <&ccu RST_BUS_HDMI0>; + reset-names = "phy"; + #phy-cells = <0>; + }; + rtc: rtc@1f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; -- cgit v1.2.3 From f0842bc5637c45dec92b0c911d586279267559bf Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Thu, 1 Mar 2018 22:34:41 +0100 Subject: ARM: dts: sun8i: h3: Enable HDMI output on H3 boards Enable HDMI output on all boards which have HDMI connector. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 25 ++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 24 +++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 25 ++++++++++++++++++++++ 8 files changed, 199 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index 9c1bc472fb1c..30540dc8e0c5 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -61,6 +61,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -100,6 +111,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -129,6 +144,16 @@ }; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 870aabcbb2d8..cf1f970b0c6f 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -61,6 +61,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -100,6 +111,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -108,6 +123,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts index d0d41eb86cb4..b20a710da7bc 100644 --- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts +++ b/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts @@ -23,6 +23,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -120,6 +131,10 @@ status = "okay"; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -143,6 +158,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts index c77fbca4f227..9412668bb888 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts @@ -49,6 +49,21 @@ aliases { ethernet0 = &emac; }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; +}; + +&de { + status = "okay"; }; &ehci1 { @@ -66,6 +81,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index 7569bd05e249..f1fc6bdca8be 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -62,6 +62,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -114,6 +125,10 @@ status = "okay"; }; +&de { + status = "okay"; +}; + &ehci1 { status = "okay"; }; @@ -125,6 +140,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts index 2e59fd296717..476ae8e387ca 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -61,6 +61,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -91,6 +102,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci1 { status = "okay"; }; @@ -99,6 +114,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index c1a8cd93c463..3328fe583c9b 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -60,6 +60,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -90,6 +101,10 @@ }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -102,9 +117,18 @@ phy-handle = <&int_mii_phy>; phy-mode = "mii"; allwinner,leds-active-low; +}; + +&hdmi { status = "okay"; }; +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index 537227b85935..cea4d647ecbf 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -60,6 +60,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -98,6 +109,10 @@ status = "okay"; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -121,6 +136,16 @@ status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; -- cgit v1.2.3 From c235edcb34651023c9eb1c5c4a7cdcaf7250d02c Mon Sep 17 00:00:00 2001 From: Giulio Benetti Date: Tue, 13 Mar 2018 11:16:45 +0100 Subject: ARM: dts: sun8i-h3: Add Mali node The H3 has an ARM Mali 400 GPU, so add binding to our DT. Signed-off-by: Giulio Benetti Reviewed-by: Rob Herring Signed-off-by: Maxime Ripard --- .../devicetree/bindings/gpu/arm,mali-utgard.txt | 1 + arch/arm/boot/dts/sun8i-h3.dtsi | 27 ++++++++++++++++++++++ 2 files changed, 28 insertions(+) (limited to 'arch/arm') diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index ad876548ab5d..c1f65d1dac1d 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -10,6 +10,7 @@ Required properties: * And, optionally, one of the vendor specific compatible: + allwinner,sun4i-a10-mali + allwinner,sun7i-a20-mali + + allwinner,sun8i-h3-mali + allwinner,sun50i-h5-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index 8495deecedad..10da8ed7db81 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -79,6 +79,33 @@ , ; }; + + soc { + mali: gpu@1c40000 { + compatible = "allwinner,sun8i-h3-mali", "arm,mali-400"; + reg = <0x01c40000 0x10000>; + interrupts = , + , + , + , + , + , + ; + interrupt-names = "gp", + "gpmmu", + "pp0", + "ppmmu0", + "pp1", + "ppmmu1", + "pmu"; + clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>; + clock-names = "bus", "core"; + resets = <&ccu RST_BUS_GPU>; + + assigned-clocks = <&ccu CLK_GPU>; + assigned-clock-rates = <384000000>; + }; + }; }; &ccu { -- cgit v1.2.3