summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2017-06-07ibmvnic: Return failure on attempted mtu changeJohn Allen1-0/+6
Changing the mtu is currently not supported in the ibmvnic driver. Implement .ndo_change_mtu in the driver so that attempting to use ifconfig to change the mtu will fail and present the user with an error message. Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-07bnx2x: fix pf2vf bulletin DMA mapping leakMichal Schmidt1-1/+1
When freeing VF's DMA mappings, an already NULLed pointer was checked again due to an apparent copy&paste error. Consequently, the pf2vf bulletin DMA mapping was not freed. Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06net: stmmac: fix a broken u32 less than zero checkColin Ian King1-1/+1
The check that queue is less or equal to zero is always true because queue is a u32; queue is decremented and will wrap around and never go -ve. Fix this by making queue an int. Detected by CoverityScan, CID#1428988 ("Unsigned compared against 0") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06net: stmmac: fix completely hung TX when using TSONiklas Cassel1-1/+1
stmmac_tso_allocator can fail to set the Last Descriptor bit on a descriptor that actually was the last descriptor. This happens when the buffer of the last descriptor ends up having a size of exactly TSO_MAX_BUFF_SIZE. When the IP eventually reaches the next last descriptor, which actually has the bit set, the DMA will hang. When the DMA hangs, we get a tx timeout, however, since stmmac does not do a complete reset of the IP in stmmac_tx_timeout, we end up in a state with completely hung TX. Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06net: ethoc: enable NAPI before poll may be scheduledMax Filippov1-1/+2
ethoc_reset enables device interrupts, ethoc_interrupt may schedule a NAPI poll before NAPI is enabled in the ethoc_open, which results in device being unable to send or receive anything until it's closed and reopened. In case the device is flooded with ingress packets it may be unable to recover at all. Move napi_enable above ethoc_reset in the ethoc_open to fix that. Fixes: a1702857724f ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Tobias Klauser <tklauser@distanz.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06ravb: Fix use-after-free on `ifconfig eth0 down`Eugeniu Rosca1-12/+12
Commit a47b70ea86bd ("ravb: unmap descriptors when freeing rings") has introduced the issue seen in [1] reproduced on H3ULCB board. Fix this by relocating the RX skb ringbuffer free operation, so that swiotlb page unmapping can be done first. Freeing of aligned TX buffers is not relevant to the issue seen in [1]. Still, reposition TX free calls as well, to have all kfree() operations performed consistently _after_ dma_unmap_*()/dma_free_*(). [1] Console screenshot with the problem reproduced: salvator-x login: root root@salvator-x:~# ifconfig eth0 up Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: \ attached PHY driver [Micrel KSZ9031 Gigabit PHY] \ (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=235) IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready root@salvator-x:~# root@salvator-x:~# ifconfig eth0 down ================================================================== BUG: KASAN: use-after-free in swiotlb_tbl_unmap_single+0xc4/0x35c Write of size 1538 at addr ffff8006d884f780 by task ifconfig/1649 CPU: 0 PID: 1649 Comm: ifconfig Not tainted 4.12.0-rc4-00004-g112eb07287d1 #32 Hardware name: Renesas H3ULCB board based on r8a7795 (DT) Call trace: [<ffff20000808f11c>] dump_backtrace+0x0/0x3a4 [<ffff20000808f4d4>] show_stack+0x14/0x1c [<ffff20000865970c>] dump_stack+0xf8/0x150 [<ffff20000831f8b0>] print_address_description+0x7c/0x330 [<ffff200008320010>] kasan_report+0x2e0/0x2f4 [<ffff20000831eac0>] check_memory_region+0x20/0x14c [<ffff20000831f054>] memcpy+0x48/0x68 [<ffff20000869ed50>] swiotlb_tbl_unmap_single+0xc4/0x35c [<ffff20000869fcf4>] unmap_single+0x90/0xa4 [<ffff20000869fd14>] swiotlb_unmap_page+0xc/0x14 [<ffff2000080a2974>] __swiotlb_unmap_page+0xcc/0xe4 [<ffff2000088acdb8>] ravb_ring_free+0x514/0x870 [<ffff2000088b25dc>] ravb_close+0x288/0x36c [<ffff200008aaf8c4>] __dev_close_many+0x14c/0x174 [<ffff200008aaf9b4>] __dev_close+0xc8/0x144 [<ffff200008ac2100>] __dev_change_flags+0xd8/0x194 [<ffff200008ac221c>] dev_change_flags+0x60/0xb0 [<ffff200008ba2dec>] devinet_ioctl+0x484/0x9d4 [<ffff200008ba7b78>] inet_ioctl+0x190/0x194 [<ffff200008a78c44>] sock_do_ioctl+0x78/0xa8 [<ffff200008a7a128>] sock_ioctl+0x110/0x3c4 [<ffff200008365a70>] vfs_ioctl+0x90/0xa0 [<ffff200008365dbc>] do_vfs_ioctl+0x148/0xc38 [<ffff2000083668f0>] SyS_ioctl+0x44/0x74 [<ffff200008083770>] el0_svc_naked+0x24/0x28 The buggy address belongs to the page: page:ffff7e001b6213c0 count:0 mapcount:0 mapping: (null) index:0x0 flags: 0x4000000000000000() raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff raw: 0000000000000000 ffff7e001b6213e0 0000000000000000 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8006d884f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff8006d884f700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff8006d884f780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff8006d884f800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff8006d884f880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ================================================================== Disabling lock debugging due to kernel taint root@salvator-x:~# Fixes: a47b70ea86bd ("ravb: unmap descriptors when freeing rings") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06net: stmmac: ensure jumbo_frm error return is correctly checked for -ve valueColin Ian King1-1/+2
The current comparison of entry < 0 will never be true since entry is an unsigned integer. Make entry an int to ensure -ve error return values from the call to jumbo_frm are correctly being caught. Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06Merge tag 'wireless-drivers-for-davem-2017-06-06' of ↵David S. Miller19-79/+118
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.12 It has been a slow start of cycle and this the first set of fixes for 4.12. Nothing really major here. wcn36xx * fix an issue with module reload brcmfmac * fix aligment regression on 64 bit systems iwlwifi * fixes for memory leaks, runtime PM, memory initialisation and other smaller problems * fix IBSS on devices using DQA mode (7260 and up) * fix the minimum firmware API requirement for 7265D, 3168, 8000 and 8265 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06i40e/i40evf: proper update of the page_offset fieldBjörn Töpel2-2/+4
In f8b45b74cc62 ("i40e/i40evf: Use build_skb to build frames") i40e_build_skb updates the page_offset field with an incorrect offset, which can lead to data corruption. This patch updates page_offset correctly, by properly setting truesize. Note that the bug only appears on architectures where PAGE_SIZE is 8192 or larger. Fixes: f8b45b74cc62 ("i40e/i40evf: Use build_skb to build frames") Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-06-06i40e: Fix state flags for bit set and clean operations of PFMauro S. M. Rodrigues1-18/+18
Commit 0da36b9774cc ("i40e: use DECLARE_BITMAP for state fields") introduced changes in the way i40e works with state flags converting them to bitmaps using kernel bitmap API. This change introduced a regression due to a mistaken substitution using __I40E_VSI_DOWN instead of __I40E_DOWN when testing state of a PF at i40e_reset_subtask() function. This caused a flood in the kernel log with the follow message: [49.013] i40e 0002:01:00.0: bad reset request 0x00000020 Commit d19cb64b9222 ("i40e: separate PF and VSI state flags") also introduced some misuse of the VSI and PF flags, so both could be considered as the offenders. This patch simply fixes the flags where it makes sense by changing __I40E_VSI_DOWN to __I40E_DOWN. Fixes: 0da36b9774cc ("i40e: use DECLARE_BITMAP for state fields") Fixes: d19cb64b9222 ("i40e: separate PF and VSI state flags") Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2017-06-05Merge tag 'iwlwifi-for-kalle-2017-06-05' of ↵Kalle Valo17-78/+115
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes Fixes for 4.12: * Some memory leaks; * IBSS support; * Some bugzilla bugs; * Some runtime PM fixes; * Rate-scaling issues; * Some locking problems;
2017-06-05iwlwifi: fix host command memory leaksShahar S Matityahu1-3/+6
Sending host command with CMD_WANT_SKB flag demands the release of the response buffer with iwl_free_resp function. The patch adds the memory release in all the relevant places Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: fix min API version for 7265D, 3168, 8000 and 8265Luca Coelho2-4/+4
In a previous commit, we removed support for API versions earlier than 22 for these NICs. By mistake, the *_UCODE_API_MIN definitions were set to 17. Fix that. Fixes: 4b87e5af638b ("iwlwifi: remove support for fw older than -17 and -22") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: clear new beacon command template structJohannes Berg1-1/+1
Clear the struct so that all reserved fields are zero when we send the struct down to the device. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: don't fail when removing a key from an inexisting staLuca Coelho1-8/+5
The iwl_mvm_remove_sta_key() function handles removing a key when the sta doesn't exist anymore. Mistakenly, this was changed to return an error while fixing another bug. If the mvm_sta doesn't exist, we continue normally, but just don't try to remove the igtk key. Fixes: cd4d23c1ea9b ("iwlwifi: mvm: Fix removal of IGTK") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: pcie: only use d0i3 in suspend/resume if system_pm is set to d0i3Luca Coelho1-2/+4
We only need to handle d0i3 entry and exit during suspend resume if system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry failures will cause suspend to fail. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791 Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: fix firmware debug restart recordingEmmanuel Grumbach4-19/+27
When we want to stop the recording of the firmware debug and restart it later without reloading the firmware we don't need to resend the configuration that comes with host commands. Sending those commands confused the hardware and led to an NMI 0x66. Change the flow as following: * read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL) * clear those registers * wait for the hardware to complete its write to the buffer * get the data * restore the value of those registers (to restart the recording) For early start (where the configuration is already compiled in the firmware), we don't need to set those registers after the firmware has been loaded, but only when we want to restart the recording without having restarted the firmware. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: tt: move ucode_loaded check under mutexJohannes Berg1-3/+5
The ucode_loaded check should be under the mutex, since it can otherwise change state after we looked at it and before we got the mutex. Fix that. Fixes: 5c89e7bc557e ("iwlwifi: mvm: add registration to cooling device") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: support ibss in dqa modeLiad Kaufman1-1/+12
Allow working IBSS also when working in DQA mode. This is done by setting it to treat the queues the same as a BSS AP treats the queues. Fixes: 7948b87308a4 ("iwlwifi: mvm: enable dynamic queue allocation mode") Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: Fix command queue number on d0i3 flowHaim Dreyfuss1-1/+4
During d0i3 flow we flush all the queue except from the command queue. Currently, in this flow the command queue is hard coded to 9. In DQA the command queue number has changed from 9 to 0. Fix that. This fixes a problem in runtime PM resume flow. Fixes: 097129c9e625 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode") Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05iwlwifi: mvm: rs: start using LQ command colorGregory Greenman6-36/+47
Up until now, the driver was comparing the rate reported by the FW and the rate of the latest LQ command to avoid processing data belonging to the old LQ command. Recently, FW changed the meaning of the initial rate field in tx response and it holds the actual rate (which is not necessarily the initial rate of LQ's rate table). Use instead LQ cmd color to be able to filter out tx responses/BA notifications which where sent during earlier LQ commands' time frame. This fixes some throughput degradation in noisy environments. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2017-06-05net/mlx4: Check if Granular QoS per VF has been enabled before updating QP ↵Ido Shamay2-5/+17
qos_vport The Granular QoS per VF feature must be enabled in FW before it can be used. Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW command) if the feature has not been enabled -- the FW returns an error if this is attempted. Fixes: 08068cd5683f ("net/mlx4: Added qos_vport QP configuration in VST mode") Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-05net: phy: fix kernel-doc warningsRandy Dunlap1-1/+1
Fix kernel-doc warnings (typo) in drivers/net/phy/phy.c: ..//drivers/net/phy/phy.c:259: warning: No description found for parameter 'features' ..//drivers/net/phy/phy.c:259: warning: Excess function parameter 'feature' description in 'phy_lookup_setting' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-04net/mlx4: Fix the check in attaching steering rulesTalat Batheesh3-9/+24
Our previous patch (cited below) introduced a regression for RAW Eth QPs. Fix it by checking if the QP number provided by user-space exists, hence allowing steering rules to be added for valid QPs only. Fixes: 89c557687a32 ("net/mlx4_en: Avoid adding steering rules with invalid ring") Reported-by: Or Gerlitz <gerlitz.or@gmail.com> Signed-off-by: Talat Batheesh <talatb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-04geneve: fix needed_headroom and max_mtu for collect_metadataEric Garver1-1/+1
Since commit 9b4437a5b870 ("geneve: Unify LWT and netdev handling.") when using COLLECT_METADATA geneve devices are created with too small of a needed_headroom and too large of a max_mtu. This is because ip_tunnel_info_af() is not valid with the device level info when using COLLECT_METADATA and we mistakenly fall into the IPv4 case. For COLLECT_METADATA, always use the worst case of ipv6 since both sockets are created. Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.") Signed-off-by: Eric Garver <e@erig.me> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-04amd-xgbe: use PAGE_ALLOC_COSTLY_ORDER in xgbe_map_rx_bufferMichal Hocko1-3/+2
xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case actually because orders larger than that are costly. And even that applies only to sleeping allocations which is not the case here. We simply do not perform any costly operations like reclaim or compaction for those. Simplify the code by dropping the order calculation and use PAGE_ALLOC_COSTLY_ORDER directly. Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-04net: qcom/emac: do not use hardware mdio automatic pollingTimur Tabi3-93/+6
Use software polling (PHY_POLL) to check for link state changes instead of relying on the EMAC's hardware polling feature. Some PHY drivers are unable to get a functioning link because the HW polling is not robust enough. The EMAC is able to poll the PHY on the MDIO bus looking for link state changes (via the Link Status bit in the Status Register at address 0x1). When the link state changes, the EMAC triggers an interrupt and tells the driver what the new state is. The feature eliminates the need for software to poll the MDIO bus. Unfortunately, this feature is incompatible with phylib, because it ignores everything that the PHY core and PHY drivers are trying to do. In particular: 1. It assumes a compatible register set, so PHYs with different registers may not work. 2. It doesn't allow for hardware errata that have work-arounds implemented in the PHY driver. 3. It doesn't support multiple register pages. If the PHY core switches the register set to another page, the EMAC won't know the page has changed and will still attempt to read the same PHY register. 4. It only checks the copper side of the link, not the SGMII side. Some PHY drivers (e.g. at803x) may also check the SGMII side, and report the link as not ready during autonegotiation if the SGMII link is still down. Phylib then waits for another interrupt to query the PHY again, but the EMAC won't send another interrupt because it thinks the link is up. Cc: stable@vger.kernel.org # 4.11.x Tested-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02virtio_net: lower limit on buffer sizeMichael S. Tsirkin1-2/+3
commit d85b758f72b0 ("virtio_net: fix support for small rings") was supposed to increase the buffer size for small rings but had an unintentional side effect of decreasing it for large rings. This seems to break some setups - it's not yet clear why, but increasing buffer size back to what it was before helps. Fixes: d85b758f72b0 ("virtio_net: fix support for small rings") Reported-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: "J. Bruce Fields" <bfields@fieldses.org> Tested-by: Mikulas Patocka <mpatocka@redhat.com> Tested-by: "J. Bruce Fields" <bfields@fieldses.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02qlcnic: Fix tunnel offload for 82xx adaptersChopra, Manish4-2/+30
Qlogic's 82xx series adapter doesn't support tunnel offloads, driver incorrectly assumes that it is supported and causes firmware hang while running tunnel IO. This patch fixes this by not advertising tunnel offloads for 82xx adapters. Signed-off-by: Manish Chopra <manish.chopra@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02vxlan: fix use-after-free on deletionMark Bloch1-6/+13
Adding a vxlan interface to a socket isn't symmetrical, while adding is done in vxlan_open() the deletion is done in vxlan_dellink(). This can cause a use-after-free error when we close the vxlan interface before deleting it. We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call it from vxlan_stop() to match the call from vxlan_open(). Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope") Acked-by: Jiri Benc <jbenc@redhat.com> Tested-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Mark Bloch <markb@mellanox.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02ibmvnic: Remove module author mailing addressThomas Falcon1-1/+1
The original author left the project and so far has not responded to emails sent to the listed address. Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02net: ethernet: stmmac: Fix altr_tse_pcs SGMII InitializationThor Thayer1-1/+5
Fix NETDEV WATCHDOG timeout on startup by adding missing register writes that properly setup SGMII. Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02cxgb4: avoid enabling napi twice to the same queueGanesh Goudar1-0/+4
Take uld mutex to avoid race between cxgb_up() and cxgb4_register_uld() to enable napi for the same uld queue. Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02net: systemport: Fix missing Wake-on-LAN interrupt for SYSTEMPORT LiteFlorian Fainelli1-2/+5
On SYSTEMPORT Lite, since we have the main interrupt source in the first cell, the second cell is the Wake-on-LAN interrupt, yet the code was not properly updated to fetch the second cell, and instead looked at the third and non-existing cell for Wake-on-LAN. Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01net: phy: micrel: Restore led_mode and clk_sel on resumeLeonard Crestez1-14/+28
These bits seem to be lost after a suspend/resume cycle so just set them again. Do this by splitting the handling of these bits into a function that is also called on resume. This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01vxlan: eliminate cached dst leakLance Richardson1-3/+17
After commit 0c1d70af924b ("net: use dst_cache for vxlan device"), cached dst entries could be leaked when more than one remote was present for a given vxlan_fdb entry, causing subsequent netns operations to block indefinitely and "unregister_netdevice: waiting for lo to become free." messages to appear in the kernel log. Fix by properly releasing cached dst and freeing resources in this case. Fixes: 0c1d70af924b ("net: use dst_cache for vxlan device") Signed-off-by: Lance Richardson <lrichard@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01bnx2x: Fix Multi-CosMintz, Yuval1-1/+1
Apparently multi-cos isn't working for bnx2x quite some time - driver implements ndo_select_queue() to allow queue-selection for FCoE, but the regular L2 flow would cause it to modulo the fallback's result by the number of queues. The fallback would return a queue matching the needed tc [via __skb_tx_hash()], but since the modulo is by the number of TSS queues where number of TCs is not accounted, transmission would always be done by a queue configured into using TC0. Fixes: ada7c19e6d27 ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash") Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01cxgb4: update latest firmware version supportedGanesh Goudar1-3/+3
Change t4fw_version.h to update latest firmware version number to 1.16.45.0. Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01qlcnic: Fix a sleep-in-atomic bug in qlcnic_82xx_hw_write_wx_2M and ↵Jia-Ju Bai1-1/+1
qlcnic_82xx_hw_read_wx_2M The driver may sleep under a write spin lock, and the function call path is: qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave) crb_win_lock qlcnic_pcie_sem_lock usleep_range qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave) crb_win_lock qlcnic_pcie_sem_lock usleep_range To fix it, the usleep_range is replaced with udelay. Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-01brcmfmac: fix alignment configuration on host using 64-bit DMAArend Van Spriel1-1/+1
For SDIO the alignment requirement for transfers from device to host is configured in firmware. This configuration is limited to minimum of 4-byte alignment. However, this is not correct for platforms using 64-bit DMA when the minimum alignment should be 8 bytes. This issue appeared when the ALIGNMENT definition was set according the DMA configuration. The configuration in firmware was not using that macro defintion, but a hardcoded value of 4. Hence the driver reported alignment failures for data coming from the device and causing transfers to fail. Fixes: 6e84ab604bde ("brcmfmac: properly align buffers on certain platforms Reported-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-05-31net: freescale: fix potential null pointer dereferenceGustavo A. R. Silva1-1/+8
Add NULL check before dereferencing pointer _id_ in order to avoid a potential NULL pointer dereference. Addresses-Coverity-ID: 1397995 Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-31net: fix auto-loading of Marvell DSA driverRussell King1-0/+13
Auto-loading of the Marvell DSA driver has stopped working with recent kernels. This seems to be due to the change of binding for DSA devices, moving them from the platform bus to the MDIO bus. In order for module auto-loading to work, we need to provide a MODALIAS string in the uevent file for the device. However, the device core does not automatically provide this, and needs each bus_type to implement a uevent method to generate these strings. The MDIO bus does not provide such a method, so no MODALIAS string is provided: .# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent DRIVER=mv88e6085 OF_NAME=switch OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4 OF_COMPATIBLE_0=marvell,mv88e6085 OF_COMPATIBLE_N=1 In the case of OF-based devices, the solution is easy - of_device_uevent_modalias() does the work for us. After this is done, the uevent file looks like this: .# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent DRIVER=mv88e6085 OF_NAME=switch OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4 OF_COMPATIBLE_0=marvell,mv88e6085 OF_COMPATIBLE_N=1 MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085 which results in auto-loading of the Marvell DSA driver on Clearfog platforms. Fixes: c0405563a613 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-31net: phy: fix marvell phy status readingRussell King1-2/+0
The Marvell driver incorrectly provides phydev->lp_advertising as the logical and of the link partner's advert and our advert. This is incorrect - this field is supposed to store the link parter's unmodified advertisment. This allows ethtool to report the correct link partner auto-negotiation status. Fixes: be937f1f89ca ("Marvell PHY m88e1111 driver fix") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-30net/mlx5: avoid build warning for uniprocessorArnd Bergmann1-3/+2
Building the driver with CONFIG_SMP disabled results in a harmless warning: ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint': ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable] It's better to express the conditional compilation using IS_ENABLED() here, as that lets the compiler see what the intented use for the variable is, and that it can be silently discarded. Fixes: b665d98edc9a ("net/mlx5: Tolerate irq_set_affinity_hint() failures") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-30net: dsa: mv88e6xxx: Add missing static to stub functionsArnd Bergmann1-3/+3
'static' was not enough, the helpers must be 'static inline' net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function] net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function] Fixes: c21fbe29f858 ("net: dsa: mv88e6xxx: Add missing static to stub functions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-30qed: Don't log missing periodic stats by defaultMintz, Yuval1-1/+2
Current implementation lacks the logic for providing management firmware with RDMA-related statistics; [much] worse than that - it logs such events by default to system logs. Since the statistics' gathering is done periodically, using sufficiently new management firmware the system logs would get filled with these unnecessary prints. For now, reduce the verbosity of the log so that it would not be logged by default. Fixes: 6c75424612a7 ("qed: Add support for NCSI statistics") Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-30cxgb4: avoid crash on PCI error recovery pathGuilherme G. Piccoli2-10/+20
During PCI error recovery process, specifically on eeh_err_detected() we might have a NULL netdev struct, hence a direct dereference will lead to a kernel oops. This was observed with latest upstream kernel (v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines. This patch checks for NULL pointer and avoids the crash, both in eeh_err_detected() and eeh_resume(). Also, we avoid to trigger a fatal error or to try disabling interrupts on FW during PCI error recovery, because: (a) driver might not be able to accurately access PCI regions in this case, and (b) trigger a fatal error _during_ the recovery steps is a mistake that could prevent the recovery path to complete successfully. Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-28net: dsa: mv88e6xxx: Add missing static to stub functionsAndrew Lunn1-3/+3
Stub functions in header files need to be static, or we can have multiple definitions errors. Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 6335e9f2446b ("net: dsa: mv88e6xxx: mv88e6390X SERDES support") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-27hdlcdrv: Fix divide by zero in hdlcdrv_ioctlFiro Yang1-0/+2
syszkaller fuzzer triggered a divide by zero, when set calibration through ioctl(). To fix it, test 'bitrate' if it is negative or 0, just return -EINVAL. Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Firo Yang <firogm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-26net: ethernet: ax88796: don't call free_irq without request_irq firstUwe Kleine-König1-5/+2
The function ax_init_dev (which is called only from the driver's .probe function) calls free_irq in the error path without having requested the irq in the first place. So drop the free_irq call in the error path. Fixes: 825a2ff1896e ("AX88796 network driver") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 20:44:41 +0000