diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-class-mtd | 17 | ||||
| -rw-r--r-- | Documentation/DocBook/mtdnand.tmpl | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/atmel-nand.txt | 28 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/fsmc-nand.txt | 25 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/partition.txt | 1 |
5 files changed, 67 insertions, 6 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index 3105644b3bfc..bfd119ace6ad 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -128,9 +128,8 @@ KernelVersion: 3.4 Contact: linux-mtd@lists.infradead.org Description: Maximum number of bit errors that the device is capable of - correcting within each region covering an ecc step. This will - always be a non-negative integer. Note that some devices will - have multiple ecc steps within each writesize region. + correcting within each region covering an ECC step (see + ecc_step_size). This will always be a non-negative integer. In the case of devices lacking any ECC capability, it is 0. @@ -173,3 +172,15 @@ Description: This is generally applicable only to NAND flash devices with ECC capability. It is ignored on devices lacking ECC capability; i.e., devices for which ecc_strength is zero. + +What: /sys/class/mtd/mtdX/ecc_step_size +Date: May 2013 +KernelVersion: 3.10 +Contact: linux-mtd@lists.infradead.org +Description: + The size of a single region covered by ECC, known as the ECC + step. Devices may have several equally sized ECC steps within + each writesize region. + + It will always be a non-negative integer. In the case of + devices lacking any ECC capability, it is 0. diff --git a/Documentation/DocBook/mtdnand.tmpl b/Documentation/DocBook/mtdnand.tmpl index fe122d6e686f..a248f42a121e 100644 --- a/Documentation/DocBook/mtdnand.tmpl +++ b/Documentation/DocBook/mtdnand.tmpl @@ -1224,8 +1224,6 @@ in this page</entry> #define NAND_BBT_CREATE 0x00000200 /* Search good / bad pattern through all pages of a block */ #define NAND_BBT_SCANALLPAGES 0x00000400 -/* Scan block empty during good / bad block scan */ -#define NAND_BBT_SCANEMPTY 0x00000800 /* Write bbt if neccecary */ #define NAND_BBT_WRITE 0x00001000 /* Read and write back block contents when writing bbt */ diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index d555421ea49f..c4728839d0c1 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -15,6 +15,7 @@ Required properties: optional gpio and may be set to 0 if not present. Optional properties: +- atmel,nand-has-dma : boolean to support dma transfer for nand read/write. - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". @@ -29,6 +30,14 @@ Optional properties: sector size 1024. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false +- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash + - Required properties: + - compatible : "atmel,sama5d3-nfc". + - reg : should specify the address and size used for NFC command registers, + NFC registers and NFC Sram. NFC Sram address and size can be absent + if don't want to use it. + - Optional properties: + - atmel,write-by-sram: boolean to enable NFC write by sram. Examples: nand0: nand@40000000,0 { @@ -77,3 +86,22 @@ nand0: nand@40000000 { ... }; }; + +/* for NFC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ... + nfc@70000000 { + compatible = "atmel,sama5d3-nfc"; + #address-cells = <1>; + #size-cells = <1>; + reg = < + 0x70000000 0x10000000 /* NFC Command Registers */ + 0xffffc000 0x00000070 /* NFC HSMC regs */ + 0x00200000 0x00100000 /* NFC SRAM banks */ + >; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index 2240ac09f6ba..ec42935f3908 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -1,4 +1,5 @@ -* FSMC NAND +ST Microelectronics Flexible Static Memory Controller (FSMC) +NAND Interface Required properties: - compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" @@ -9,6 +10,26 @@ Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width defaults to 1 byte - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped +- timings: array of 6 bytes for NAND timings. The meanings of these bytes + are: + byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits + are valid. Zero means one clockcycle, 15 means 16 clock + cycles. + byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR. + byte 2 THIZ : number of HCLK clock cycles during which the data bus is + kept in Hi-Z (tristate) after the start of a write access. + Only valid for write transactions. Zero means zero cycles, + 255 means 255 cycles. + byte 3 THOLD : number of HCLK clock cycles to hold the address (and data + when writing) after the command deassertation. Zero means + one cycle, 255 means 256 cycles. + byte 4 TWAIT : number of HCLK clock cycles to assert the command to the + NAND flash in response to SMWAITn. Zero means 1 cycle, + 255 means 256 cycles. + byte 5 TSET : number of HCLK clock cycles to assert the address before the + command is asserted. Zero means one cycle, 255 means 256 + cycles. +- bank: default NAND bank to use (0-3 are valid, 0 is the default). Example: @@ -24,6 +45,8 @@ Example: bank-width = <1>; nand-skip-bbtscan; + timings = /bits/ 8 <0 0 0 2 3 0>; + bank = <1>; partition@0 { ... diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 9315ac96b49b..8e5557da1955 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -4,6 +4,7 @@ Partitions can be represented by sub-nodes of an mtd device. This can be used on platforms which have strong conventions about which portions of a flash are used for what purposes, but which don't use an on-flash partition table such as RedBoot. +NOTE: if the sub-node has a compatible string, then it is not a partition. #address-cells & #size-cells must both be present in the mtd device. There are two valid values for both: |