diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt | 14 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt | 1 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/i2c-stm32.txt | 33 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt | 42 | ||||
| -rw-r--r-- | Documentation/i2c/busses/i2c-i801 | 1 | ||||
| -rw-r--r-- | Documentation/i2c/muxes/i2c-mux-gpio | 20 |
6 files changed, 100 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt index cf53d5fba20a..aa097045a10e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -19,7 +19,14 @@ Optional Properties: - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all children in idle state. This is necessary for example, if there are several multiplexers on the bus and the devices behind them use same I2C addresses. - + - interrupt-parent: Phandle for the interrupt controller that services + interrupts for this device. + - interrupts: Interrupt mapping for IRQ. + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Example: @@ -29,6 +36,11 @@ Example: #size-cells = <0>; reg = <0x74>; + interrupt-parent = <&ipic>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + i2c@2 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 7716acc55dec..ae9c2a735f39 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,iic-r8a7793" (R-Car M2-N) - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) + - "renesas,iic-r8a7796" (R-Car M3-W) - "renesas,iic-sh73a0" (SH-Mobile AG5) - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt new file mode 100644 index 000000000000..78eaf7b718ed --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -0,0 +1,33 @@ +* I2C controller embedded in STMicroelectronics STM32 I2C platform + +Required properties : +- compatible : Must be "st,stm32f4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : Must contain the interrupt id for I2C event and then the + interrupt id for I2C error. +- resets: Must contain the phandle to the reset controller. +- clocks: Must contain the input clock of the I2C instance. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + + i2c@40005400 { + compatible = "st,stm32f4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc 277>; + clocks = <&rcc 0 149>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt new file mode 100644 index 000000000000..ab240e10debc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra186 BPMP I2C controller + +In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW +devices, such as the I2C controller for the power management I2C bus. Software +running on other CPUs must perform IPC to the BPMP in order to execute +transactions on that I2C bus. This binding describes an I2C bus that is +accessed in such a fashion. + +The BPMP I2C node must be located directly inside the main BPMP node. See +../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding. + +This node represents an I2C controller. See ../i2c/i2c.txt for details of the +core I2C binding. + +Required properties: +- compatible: + Array of strings. + One of: + - "nvidia,tegra186-bpmp-i2c". +- #address-cells: Address cells for I2C device address. + Single-cell integer. + Must be <1>. +- #size-cells: + Single-cell integer. + Must be <0>. +- nvidia,bpmp-bus-id: + Single-cell integer. + Indicates the I2C bus number this DT node represent, as defined by the + BPMP firmware. + +Example: + +bpmp { + ... + + i2c { + compatible = "nvidia,tegra186-bpmp-i2c"; + #address-cells = <1>; + #size-cells = <0>; + nvidia,bpmp-bus-id = <5>; + }; +}; diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index 1bba38dd2637..820d9040de16 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -33,6 +33,7 @@ Supported adapters: * Intel DNV (SOC) * Intel Broxton (SOC) * Intel Lewisburg (PCH) + * Intel Gemini Lake (SOC) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/i2c/muxes/i2c-mux-gpio b/Documentation/i2c/muxes/i2c-mux-gpio index d4d91a53fc39..7a8d7d261632 100644 --- a/Documentation/i2c/muxes/i2c-mux-gpio +++ b/Documentation/i2c/muxes/i2c-mux-gpio @@ -1,11 +1,11 @@ -Kernel driver i2c-gpio-mux +Kernel driver i2c-mux-gpio Author: Peter Korsgaard <peter.korsgaard@barco.com> Description ----------- -i2c-gpio-mux is an i2c mux driver providing access to I2C bus segments +i2c-mux-gpio is an i2c mux driver providing access to I2C bus segments from a master I2C bus and a hardware MUX controlled through GPIO pins. E.G.: @@ -26,16 +26,16 @@ according to the settings of the GPIO pins 1..N. Usage ----- -i2c-gpio-mux uses the platform bus, so you need to provide a struct +i2c-mux-gpio uses the platform bus, so you need to provide a struct platform_device with the platform_data pointing to a struct -gpio_i2cmux_platform_data with the I2C adapter number of the master +i2c_mux_gpio_platform_data with the I2C adapter number of the master bus, the number of bus segments to create and the GPIO pins used -to control it. See include/linux/i2c-gpio-mux.h for details. +to control it. See include/linux/i2c-mux-gpio.h for details. E.G. something like this for a MUX providing 4 bus segments controlled through 3 GPIO pins: -#include <linux/i2c-gpio-mux.h> +#include <linux/i2c-mux-gpio.h> #include <linux/platform_device.h> static const unsigned myboard_gpiomux_gpios[] = { @@ -46,7 +46,7 @@ static const unsigned myboard_gpiomux_values[] = { 0, 1, 2, 3 }; -static struct gpio_i2cmux_platform_data myboard_i2cmux_data = { +static struct i2c_mux_gpio_platform_data myboard_i2cmux_data = { .parent = 1, .base_nr = 2, /* optional */ .values = myboard_gpiomux_values, @@ -57,7 +57,7 @@ static struct gpio_i2cmux_platform_data myboard_i2cmux_data = { }; static struct platform_device myboard_i2cmux = { - .name = "i2c-gpio-mux", + .name = "i2c-mux-gpio", .id = 0, .dev = { .platform_data = &myboard_i2cmux_data, @@ -66,14 +66,14 @@ static struct platform_device myboard_i2cmux = { If you don't know the absolute GPIO pin numbers at registration time, you can instead provide a chip name (.chip_name) and relative GPIO pin -numbers, and the i2c-gpio-mux driver will do the work for you, +numbers, and the i2c-mux-gpio driver will do the work for you, including deferred probing if the GPIO chip isn't immediately available. Device Registration ------------------- -When registering your i2c-gpio-mux device, you should pass the number +When registering your i2c-mux-gpio device, you should pass the number of any GPIO pin it uses as the device ID. This guarantees that every instance has a different ID. |