diff options
Diffstat (limited to 'Documentation/devicetree')
240 files changed, 5210 insertions, 810 deletions
diff --git a/Documentation/devicetree/00-INDEX b/Documentation/devicetree/00-INDEX deleted file mode 100644 index 8c4102c6a5e7..000000000000 --- a/Documentation/devicetree/00-INDEX +++ /dev/null @@ -1,12 +0,0 @@ -Documentation for device trees, a data structure by which bootloaders pass -hardware layout to Linux in a device-independent manner, simplifying hardware -probing. This subsystem is maintained by Grant Likely -<grant.likely@secretlab.ca> and has a mailing list at -https://lists.ozlabs.org/listinfo/devicetree-discuss - -00-INDEX - - this file -booting-without-of.txt - - Booting Linux without Open Firmware, describes history and format of device trees. -usage-model.txt - - How Linux uses DT and what DT aims to solve.
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/arm/al,alpine.txt b/Documentation/devicetree/bindings/arm/al,alpine.txt index f404a4f9b165..d00debe2e86f 100644 --- a/Documentation/devicetree/bindings/arm/al,alpine.txt +++ b/Documentation/devicetree/bindings/arm/al,alpine.txt @@ -14,75 +14,3 @@ compatible: must contain "al,alpine" ... } - -* CPU node: - -The Alpine platform includes cortex-a15 cores. -enable-method: must be "al,alpine-smp" to allow smp [1] - -Example: - -cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "al,alpine-smp"; - - cpu@0 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <0>; - }; - - cpu@1 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <1>; - }; - - cpu@2 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <2>; - }; - - cpu@3 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <3>; - }; -}; - - -* Alpine CPU resume registers - -The CPU resume register are used to define required resume address after -reset. - -Properties: -- compatible : Should contain "al,alpine-cpu-resume". -- reg : Offset and length of the register set for the device - -Example: - -cpu_resume { - compatible = "al,alpine-cpu-resume"; - reg = <0xfbff5ed0 0x30>; -}; - -* Alpine System-Fabric Service Registers - -The System-Fabric Service Registers allow various operation on CPU and -system fabric, like powering CPUs off. - -Properties: -- compatible : Should contain "al,alpine-sysfabric-service" and "syscon". -- reg : Offset and length of the register set for the device - -Example: - -nb_service { - compatible = "al,alpine-sysfabric-service", "syscon"; - reg = <0xfb070000 0x10000>; -}; - -[1] arm/cpu-enable-method/al,alpine-smp diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index b5c2b5c35766..4498292b833d 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -57,12 +57,17 @@ Boards with the Amlogic Meson AXG A113D SoC shall have the following properties: Required root node property: compatible: "amlogic,a113d", "amlogic,meson-axg"; +Boards with the Amlogic Meson G12A S905D2 SoC shall have the following properties: + Required root node property: + compatible: "amlogic,g12a"; + Board compatible values (alphabetically, grouped by SoC): - "geniatech,atv1200" (Meson6) - "minix,neo-x8" (Meson8) + - "endless,ec100" (Meson8b) - "hardkernel,odroid-c1" (Meson8b) - "tronfy,mxq" (Meson8b) @@ -101,6 +106,8 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,s400" (Meson axg a113d) + - "amlogic,u200" (Meson g12a s905d2) + Amlogic Meson Firmware registers Interface ------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 31220b54d85d..4bf1b4da7659 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -70,173 +70,3 @@ compatible: must be one of: - "atmel,samv71q19" - "atmel,samv71q20" - "atmel,samv71q21" - -Chipid required properties: -- compatible: Should be "atmel,sama5d2-chipid" -- reg : Should contain registers location and length - -PIT Timer required properties: -- compatible: Should be "atmel,at91sam9260-pit" -- reg: Should contain registers location and length -- interrupts: Should contain interrupt for the PIT which is the IRQ line - shared across all System Controller members. - -System Timer (ST) required properties: -- compatible: Should be "atmel,at91rm9200-st", "syscon", "simple-mfd" -- reg: Should contain registers location and length -- interrupts: Should contain interrupt for the ST which is the IRQ line - shared across all System Controller members. -- clocks: phandle to input clock. -Its subnodes can be: -- watchdog: compatible should be "atmel,at91rm9200-wdt" - -RSTC Reset Controller required properties: -- compatible: Should be "atmel,<chip>-rstc". - <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" -- reg: Should contain registers location and length -- clocks: phandle to input clock. - -Example: - - rstc@fffffd00 { - compatible = "atmel,at91sam9260-rstc"; - reg = <0xfffffd00 0x10>; - clocks = <&clk32k>; - }; - -RAMC SDRAM/DDR Controller required properties: -- compatible: Should be "atmel,at91rm9200-sdramc", "syscon" - "atmel,at91sam9260-sdramc", - "atmel,at91sam9g45-ddramc", - "atmel,sama5d3-ddramc", -- reg: Should contain registers location and length - -Examples: - - ramc0: ramc@ffffe800 { - compatible = "atmel,at91sam9g45-ddramc"; - reg = <0xffffe800 0x200>; - }; - -SHDWC Shutdown Controller - -required properties: -- compatible: Should be "atmel,<chip>-shdwc". - <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". -- reg: Should contain registers location and length -- clocks: phandle to input clock. - -optional properties: -- atmel,wakeup-mode: String, operation mode of the wakeup mode. - Supported values are: "none", "high", "low", "any". -- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf). - -optional at91sam9260 properties: -- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. - -optional at91sam9rl properties: -- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. -- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. - -optional at91sam9x5 properties: -- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. - -Example: - - shdwc@fffffd10 { - compatible = "atmel,at91sam9260-shdwc"; - reg = <0xfffffd10 0x10>; - clocks = <&clk32k>; - }; - -SHDWC SAMA5D2-Compatible Shutdown Controller - -1) shdwc node - -required properties: -- compatible: should be "atmel,sama5d2-shdwc". -- reg: should contain registers location and length -- clocks: phandle to input clock. -- #address-cells: should be one. The cell is the wake-up input index. -- #size-cells: should be zero. - -optional properties: - -- debounce-delay-us: minimum wake-up inputs debouncer period in - microseconds. It's usually a board-related property. -- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up. - -The node contains child nodes for each wake-up input that the platform uses. - -2) input nodes - -Wake-up input nodes are usually described in the "board" part of the Device -Tree. Note also that input 0 is linked to the wake-up pin and is frequently -used. - -Required properties: -- reg: should contain the wake-up input index [0 - 15]. - -Optional properties: -- atmel,wakeup-active-high: boolean, the corresponding wake-up input described - by the child, forces the wake-up of the core power supply on a high level. - The default is to be active low. - -Example: - -On the SoC side: - shdwc@f8048010 { - compatible = "atmel,sama5d2-shdwc"; - reg = <0xf8048010 0x10>; - clocks = <&clk32k>; - #address-cells = <1>; - #size-cells = <0>; - atmel,wakeup-rtc-timer; - }; - -On the board side: - shdwc@f8048010 { - debounce-delay-us = <976>; - - input@0 { - reg = <0>; - }; - - input@1 { - reg = <1>; - atmel,wakeup-active-high; - }; - }; - -Special Function Registers (SFR) - -Special Function Registers (SFR) manage specific aspects of the integrated -memory, bridge implementations, processor and other functionality not controlled -elsewhere. - -required properties: -- compatible: Should be "atmel,<chip>-sfr", "syscon" or - "atmel,<chip>-sfrbu", "syscon" - <chip> can be "sama5d3", "sama5d4" or "sama5d2". -- reg: Should contain registers location and length - - sfr@f0038000 { - compatible = "atmel,sama5d3-sfr", "syscon"; - reg = <0xf0038000 0x60>; - }; - -Security Module (SECUMOD) - -The Security Module macrocell provides all necessary secure functions to avoid -voltage, temperature, frequency and mechanical attacks on the chip. It also -embeds secure memories that can be scrambled - -required properties: -- compatible: Should be "atmel,<chip>-secumod", "syscon". - <chip> can be "sama5d2". -- reg: Should contain registers location and length - - secumod@fc040000 { - compatible = "atmel,sama5d2-secumod", "syscon"; - reg = <0xfc040000 0x100>; - }; diff --git a/Documentation/devicetree/bindings/arm/atmel-sysregs.txt b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt new file mode 100644 index 000000000000..4b96608ad692 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt @@ -0,0 +1,171 @@ +Atmel system registers + +Chipid required properties: +- compatible: Should be "atmel,sama5d2-chipid" +- reg : Should contain registers location and length + +PIT Timer required properties: +- compatible: Should be "atmel,at91sam9260-pit" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the PIT which is the IRQ line + shared across all System Controller members. + +System Timer (ST) required properties: +- compatible: Should be "atmel,at91rm9200-st", "syscon", "simple-mfd" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the ST which is the IRQ line + shared across all System Controller members. +- clocks: phandle to input clock. +Its subnodes can be: +- watchdog: compatible should be "atmel,at91rm9200-wdt" + +RSTC Reset Controller required properties: +- compatible: Should be "atmel,<chip>-rstc". + <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" +- reg: Should contain registers location and length +- clocks: phandle to input clock. + +Example: + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + clocks = <&clk32k>; + }; + +RAMC SDRAM/DDR Controller required properties: +- compatible: Should be "atmel,at91rm9200-sdramc", "syscon" + "atmel,at91sam9260-sdramc", + "atmel,at91sam9g45-ddramc", + "atmel,sama5d3-ddramc", +- reg: Should contain registers location and length + +Examples: + + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + +SHDWC Shutdown Controller + +required properties: +- compatible: Should be "atmel,<chip>-shdwc". + <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". +- reg: Should contain registers location and length +- clocks: phandle to input clock. + +optional properties: +- atmel,wakeup-mode: String, operation mode of the wakeup mode. + Supported values are: "none", "high", "low", "any". +- atmel,wakeup-counter: Counter on Wake-up 0 (between 0x0 and 0xf). + +optional at91sam9260 properties: +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9rl properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. +- atmel,wakeup-rtt-timer: boolean to enable Real-time Timer Wake-up. + +optional at91sam9x5 properties: +- atmel,wakeup-rtc-timer: boolean to enable Real-time Clock Wake-up. + +Example: + + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + clocks = <&clk32k>; + }; + +SHDWC SAMA5D2-Compatible Shutdown Controller + +1) shdwc node + +required properties: +- compatible: should be "atmel,sama5d2-shdwc". +- reg: should contain registers location and length +- clocks: phandle to input clock. +- #address-cells: should be one. The cell is the wake-up input index. +- #size-cells: should be zero. + +optional properties: + +- debounce-delay-us: minimum wake-up inputs debouncer period in + microseconds. It's usually a board-related property. +- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up. + +The node contains child nodes for each wake-up input that the platform uses. + +2) input nodes + +Wake-up input nodes are usually described in the "board" part of the Device +Tree. Note also that input 0 is linked to the wake-up pin and is frequently +used. + +Required properties: +- reg: should contain the wake-up input index [0 - 15]. + +Optional properties: +- atmel,wakeup-active-high: boolean, the corresponding wake-up input described + by the child, forces the wake-up of the core power supply on a high level. + The default is to be active low. + +Example: + +On the SoC side: + shdwc@f8048010 { + compatible = "atmel,sama5d2-shdwc"; + reg = <0xf8048010 0x10>; + clocks = <&clk32k>; + #address-cells = <1>; + #size-cells = <0>; + atmel,wakeup-rtc-timer; + }; + +On the board side: + shdwc@f8048010 { + debounce-delay-us = <976>; + + input@0 { + reg = <0>; + }; + + input@1 { + reg = <1>; + atmel,wakeup-active-high; + }; + }; + +Special Function Registers (SFR) + +Special Function Registers (SFR) manage specific aspects of the integrated +memory, bridge implementations, processor and other functionality not controlled +elsewhere. + +required properties: +- compatible: Should be "atmel,<chip>-sfr", "syscon" or + "atmel,<chip>-sfrbu", "syscon" + <chip> can be "sama5d3", "sama5d4" or "sama5d2". +- reg: Should contain registers location and length + + sfr@f0038000 { + compatible = "atmel,sama5d3-sfr", "syscon"; + reg = <0xf0038000 0x60>; + }; + +Security Module (SECUMOD) + +The Security Module macrocell provides all necessary secure functions to avoid +voltage, temperature, frequency and mechanical attacks on the chip. It also +embeds secure memories that can be scrambled + +required properties: +- compatible: Should be "atmel,<chip>-secumod", "syscon". + <chip> can be "sama5d2". +- reg: Should contain registers location and length + + secumod@fc040000 { + compatible = "atmel,sama5d2-secumod", "syscon"; + reg = <0xfc040000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt index 1e3e29a545e2..0dcc3ea5adff 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt @@ -42,6 +42,14 @@ Raspberry Pi Compute Module Required root node properties: compatible = "raspberrypi,compute-module", "brcm,bcm2835"; +Raspberry Pi Compute Module 3 +Required root node properties: +compatible = "raspberrypi,3-compute-module", "brcm,bcm2837"; + +Raspberry Pi Compute Module 3 Lite +Required root node properties: +compatible = "raspberrypi,3-compute-module-lite", "brcm,bcm2837"; + Raspberry Pi Zero Required root node properties: compatible = "raspberrypi,model-zero", "brcm,bcm2835"; diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 5d1ad09bafb4..f8aff65ab921 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -54,9 +54,7 @@ its hardware characteristcs. clocks the core of that coresight component. The latter clock is optional. - * port or ports: The representation of the component's port - layout using the generic DT graph presentation found in - "bindings/graph.txt". + * port or ports: see "Graph bindings for Coresight" below. * Additional required properties for System Trace Macrocells (STM): * reg: along with the physical base address and length of the register @@ -73,7 +71,7 @@ its hardware characteristcs. AMBA markee): - "arm,coresight-replicator" - * port or ports: same as above. + * port or ports: see "Graph bindings for Coresight" below. * Optional properties for ETM/PTMs: @@ -96,6 +94,20 @@ its hardware characteristcs. * interrupts : Exactly one SPI may be listed for reporting the address error +Graph bindings for Coresight +------------------------------- + +Coresight components are interconnected to create a data path for the flow of +trace data generated from the "sources" to their collection points "sink". +Each coresight component must describe the "input" and "output" connections. +The connections must be described via generic DT graph bindings as described +by the "bindings/graph.txt", where each "port" along with an "endpoint" +component represents a hardware port and the connection. + + * All output ports must be listed inside a child node named "out-ports" + * All input ports must be listed inside a child node named "in-ports". + * Port address must match the hardware port number. + Example: 1. Sinks @@ -105,10 +117,11 @@ Example: clocks = <&oscclk6a>; clock-names = "apb_pclk"; - port { - etb_in_port: endpoint@0 { - slave-mode; - remote-endpoint = <&replicator_out_port0>; + in-ports { + port { + etb_in_port: endpoint@0 { + remote-endpoint = <&replicator_out_port0>; + }; }; }; }; @@ -119,10 +132,11 @@ Example: clocks = <&oscclk6a>; clock-names = "apb_pclk"; - port { - tpiu_in_port: endpoint@0 { - slave-mode; - remote-endpoint = <&replicator_out_port1>; + in-ports { + port { + tpiu_in_port: endpoint@0 { + remote-endpoint = <&replicator_out_port1>; + }; }; }; }; @@ -133,22 +147,16 @@ Example: clocks = <&oscclk6a>; clock-names = "apb_pclk"; - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* input port */ - port@0 { - reg = <0>; + in-ports { + port { etr_in_port: endpoint { - slave-mode; remote-endpoint = <&replicator2_out_port0>; }; }; + }; - /* CATU link represented by output port */ - port@1 { - reg = <1>; + out-ports { + port { etr_out_port: endpoint { remote-endpoint = <&catu_in_port>; }; @@ -163,7 +171,7 @@ Example: */ compatible = "arm,coresight-replicator"; - ports { + out-ports { #address-cells = <1>; #size-cells = <0>; @@ -181,12 +189,11 @@ Example: remote-endpoint = <&tpiu_in_port>; }; }; + }; - /* replicator input port */ - port@2 { - reg = <0>; + in-ports { + port { replicator_in_port0: endpoint { - slave-mode; remote-endpoint = <&funnel_out_port0>; }; }; @@ -199,40 +206,36 @@ Example: clocks = <&oscclk6a>; clock-names = "apb_pclk"; - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* funnel output port */ - port@0 { - reg = <0>; + out-ports { + port { funnel_out_port0: endpoint { remote-endpoint = <&replicator_in_port0>; }; }; + }; - /* funnel input ports */ - port@1 { + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { reg = <0>; funnel_in_port0: endpoint { - slave-mode; remote-endpoint = <&ptm0_out_port>; }; }; - port@2 { + port@1 { reg = <1>; funnel_in_port1: endpoint { - slave-mode; remote-endpoint = <&ptm1_out_port>; }; }; - port@3 { + port@2 { reg = <2>; funnel_in_port2: endpoint { - slave-mode; remote-endpoint = <&etm0_out_port>; }; }; @@ -248,9 +251,11 @@ Example: cpu = <&cpu0>; clocks = <&oscclk6a>; clock-names = "apb_pclk"; - port { - ptm0_out_port: endpoint { - remote-endpoint = <&funnel_in_port0>; + out-ports { + port { + ptm0_out_port: endpoint { + remote-endpoint = <&funnel_in_port0>; + }; }; }; }; @@ -262,9 +267,11 @@ Example: cpu = <&cpu1>; clocks = <&oscclk6a>; clock-names = "apb_pclk"; - port { - ptm1_out_port: endpoint { - remote-endpoint = <&funnel_in_port1>; + out-ports { + port { + ptm1_out_port: endpoint { + remote-endpoint = <&funnel_in_port1>; + }; }; }; }; @@ -278,9 +285,11 @@ Example: clocks = <&soc_smc50mhz>; clock-names = "apb_pclk"; - port { - stm_out_port: endpoint { - remote-endpoint = <&main_funnel_in_port2>; + out-ports { + port { + stm_out_port: endpoint { + remote-endpoint = <&main_funnel_in_port2>; + }; }; }; }; @@ -295,10 +304,11 @@ Example: clock-names = "apb_pclk"; interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; - port { - catu_in_port: endpoint { - slave-mode; - remote-endpoint = <&etr_out_port>; + in-ports { + port { + catu_in_port: endpoint { + remote-endpoint = <&etr_out_port>; + }; }; }; }; diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp index c2e0cc5e4cfd..35e5afb6d9ad 100644 --- a/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp @@ -14,7 +14,28 @@ Related properties: (none) Note: This enable method requires valid nodes compatible with -"al,alpine-cpu-resume" and "al,alpine-nb-service"[1]. +"al,alpine-cpu-resume" and "al,alpine-nb-service". + + +* Alpine CPU resume registers + +The CPU resume register are used to define required resume address after +reset. + +Properties: +- compatible : Should contain "al,alpine-cpu-resume". +- reg : Offset and length of the register set for the device + + +* Alpine System-Fabric Service Registers + +The System-Fabric Service Registers allow various operation on CPU and +system fabric, like powering CPUs off. + +Properties: +- compatible : Should contain "al,alpine-sysfabric-service" and "syscon". +- reg : Offset and length of the register set for the device + Example: @@ -48,5 +69,12 @@ cpus { }; }; --- -[1] arm/al,alpine.txt +cpu_resume { + compatible = "al,alpine-cpu-resume"; + reg = <0xfbff5ed0 0x30>; +}; + +nb_service { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0xfb070000 0x10000>; +}; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 96dfccc0faa8..b0198a1cf403 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -276,7 +276,7 @@ described below. Usage: optional Value type: <prop-encoded-array> Definition: A u32 value that represents the running time dynamic - power coefficient in units of mW/MHz/uV^2. The + power coefficient in units of uW/MHz/V^2. The coefficient can either be calculated from power measurements or derived by analysis. @@ -287,7 +287,7 @@ described below. Pdyn = dynamic-power-coefficient * V^2 * f - where voltage is in uV, frequency is in MHz. + where voltage is in V, frequency is in MHz. Example 1 (dual-cluster big.LITTLE system 32-bit): diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-dcfg.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-dcfg.txt new file mode 100644 index 000000000000..b5cb374dc47d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-dcfg.txt @@ -0,0 +1,19 @@ +Freescale DCFG + +DCFG is the device configuration unit, that provides general purpose +configuration and status for the device. Such as setting the secondary +core start address and release the secondary core from holdoff and startup. + +Required properties: + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-dcfg", + The following <chip>s are known to be supported: + ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. + + - reg : should contain base address and length of DCFG memory-mapped registers + +Example: + dcfg: dcfg@1ee0000 { + compatible = "fsl,ls1021a-dcfg"; + reg = <0x0 0x1ee0000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-scfg.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-scfg.txt new file mode 100644 index 000000000000..0ab67b0b216d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,layerscape-scfg.txt @@ -0,0 +1,19 @@ +Freescale SCFG + +SCFG is the supplemental configuration unit, that provides SoC specific +configuration and status registers for the chip. Such as getting PEX port +status. + +Required properties: + - compatible: Should contain a chip-specific compatible string, + Chip-specific strings are of the form "fsl,<chip>-scfg", + The following <chip>s are known to be supported: + ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. + + - reg: should contain base address and length of SCFG memory-mapped registers + +Example: + scfg: scfg@1570000 { + compatible = "fsl,ls1021a-scfg"; + reg = <0x0 0x1570000 0x0 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt new file mode 100644 index 000000000000..46d0af1f0872 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -0,0 +1,183 @@ +NXP i.MX System Controller Firmware (SCFW) +-------------------------------------------------------------------- + +The System Controller Firmware (SCFW) is a low-level system function +which runs on a dedicated Cortex-M core to provide power, clock, and +resource management. It exists on some i.MX8 processors. e.g. i.MX8QM +(QM, QP), and i.MX8QX (QXP, DX). + +The AP communicates with the SC using a multi-ported MU module found +in the LSIO subsystem. The current definition of this MU module provides +5 remote AP connections to the SC to support up to 5 execution environments +(TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces +with the LSIO DSC IP bus. The SC firmware will communicate with this MU +using the MSI bus. + +System Controller Device Node: +============================================================ + +The scu node with the following properties shall be under the /firmware/ node. + +Required properties: +------------------- +- compatible: should be "fsl,imx-scu". +- mbox-names: should include "tx0", "tx1", "tx2", "tx3", + "rx0", "rx1", "rx2", "rx3". +- mboxes: List of phandle of 4 MU channels for tx and 4 MU channels + for rx. All 8 MU channels must be in the same MU instance. + Cross instances are not allowed. The MU instance can only + be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need + to make sure use the one which is not conflict with other + execution environments. e.g. ATF. + Note: + Channel 0 must be "tx0" or "rx0". + Channel 1 must be "tx1" or "rx1". + Channel 2 must be "tx2" or "rx2". + Channel 3 must be "tx3" or "rx3". + e.g. + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 0 1 + &lsio_mu1 0 2 + &lsio_mu1 0 3 + &lsio_mu1 1 0 + &lsio_mu1 1 1 + &lsio_mu1 1 2 + &lsio_mu1 1 3>; + See Documentation/devicetree/bindings/mailbox/fsl,mu.txt + for detailed mailbox binding. + +i.MX SCU Client Device Node: +============================================================ + +Client nodes are maintained as children of the relevant IMX-SCU device node. + +Power domain bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding for the SCU power domain providers uses the generic power +domain binding[2]. + +Required properties: +- compatible: Should be "fsl,scu-pd". +- #address-cells: Should be 1. +- #size-cells: Should be 0. + +Required properties for power domain sub nodes: +- #power-domain-cells: Must be 0. + +Optional Properties: +- reg: Resource ID of this power domain. + No exist means uncontrollable by user. + See detailed Resource ID list from: + include/dt-bindings/power/imx-rsrc.h +- power-domains: phandle pointing to the parent power domain. + +Clock bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Required properties: +- compatible: Should be "fsl,imx8qxp-clock". +- #clock-cells: Should be 1. Contains the Clock ID value. +- clocks: List of clock specifiers, must contain an entry for + each required entry in clock-names +- clock-names: Should include entries "xtal_32KHz", "xtal_24MHz" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. + +See the full list of clock IDs from: +include/dt-bindings/clock/imx8qxp-clock.h + +Pinctrl bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding uses the i.MX common pinctrl binding[3]. + +Required properties: +- compatible: Should be "fsl,imx8qxp-iomuxc". + +Required properties for Pinctrl sub nodes: +- fsl,pins: Each entry consists of 3 integers which represents + the mux and config setting for one pin. The first 2 + integers <pin_id mux_mode> are specified using a + PIN_FUNC_ID macro, which can be found in + <dt-bindings/pinctrl/pads-imx8qxp.h>. + The last integer CONFIG is the pad setting value like + pull-up on this pin. + + Please refer to i.MX8QXP Reference Manual for detailed + CONFIG settings. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/power/power_domain.txt +[3] Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt + +Example (imx8qxp): +------------- +lsio_mu1: mailbox@5d1c0000 { + ... + #mbox-cells = <2>; +}; + +firmware { + scu { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", "tx1", "tx2", "tx3", + "rx0", "rx1", "rx2", "rx3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 0 1 + &lsio_mu1 0 2 + &lsio_mu1 0 3 + &lsio_mu1 1 0 + &lsio_mu1 1 1 + &lsio_mu1 1 2 + &lsio_mu1 1 3>; + + clk: clk { + compatible = "fsl,imx8qxp-clk"; + #clock-cells = <1>; + }; + + iomuxc { + compatible = "fsl,imx8qxp-iomuxc"; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + SC_P_UART0_RX_ADMA_UART0_RX 0x06000020 + SC_P_UART0_TX_ADMA_UART0_TX 0x06000020 + >; + }; + ... + }; + + imx8qx-pm { + compatible = "fsl,scu-pd"; + #address-cells = <1>; + #size-cells = <0>; + + pd_dma: dma-power-domain { + #power-domain-cells = <0>; + + pd_dma_lpuart0: dma-lpuart0@57 { + reg = <SC_R_UART_0>; + #power-domain-cells = <0>; + power-domains = <&pd_dma>; + }; + ... + }; + ... + }; + }; +}; + +serial@5a060000 { + ... + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + clocks = <&clk IMX8QXP_UART0_CLK>, + <&clk IMX8QXP_UART0_IPG_CLK>; + clock-names = "per", "ipg"; + power-domains = <&pd_dma_lpuart0>; +}; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index 8a1baa2b9723..5074aeecd327 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -57,6 +57,50 @@ i.MX6SLL EVK board Required root node properties: - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; +i.MX6 Quad Plus SABRE Smart Device Board +Required root node properties: + - compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp"; + +i.MX6 Quad Plus SABRE Automotive Board +Required root node properties: + - compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp"; + +i.MX6 DualLite SABRE Smart Device Board +Required root node properties: + - compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl"; + +i.MX6 DualLite/Solo SABRE Automotive Board +Required root node properties: + - compatible = "fsl,imx6dl-sabreauto", "fsl,imx6dl"; + +i.MX6 SoloLite EVK Board +Required root node properties: + - compatible = "fsl,imx6sl-evk", "fsl,imx6sl"; + +i.MX6 UltraLite 14x14 EVK Board +Required root node properties: + - compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul"; + +i.MX6 UltraLiteLite 14x14 EVK Board +Required root node properties: + - compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull"; + +i.MX6 ULZ 14x14 EVK Board +Required root node properties: + - compatible = "fsl,imx6ulz-14x14-evk", "fsl,imx6ull", "fsl,imx6ulz"; + +i.MX6 SoloX SDB Board +Required root node properties: + - compatible = "fsl,imx6sx-sdb", "fsl,imx6sx"; + +i.MX6 SoloX Sabre Auto Board +Required root node properties: + - compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx"; + +i.MX7 SabreSD Board +Required root node properties: + - compatible = "fsl,imx7d-sdb", "fsl,imx7d"; + Generic i.MX boards ------------------- @@ -101,45 +145,6 @@ Freescale LS1021A Platform Device Tree Bindings Required root node compatible properties: - compatible = "fsl,ls1021a"; -Freescale SoC-specific Device Tree Bindings -------------------------------------------- - -Freescale SCFG - SCFG is the supplemental configuration unit, that provides SoC specific -configuration and status registers for the chip. Such as getting PEX port -status. - Required properties: - - compatible: Should contain a chip-specific compatible string, - Chip-specific strings are of the form "fsl,<chip>-scfg", - The following <chip>s are known to be supported: - ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. - - - reg: should contain base address and length of SCFG memory-mapped registers - -Example: - scfg: scfg@1570000 { - compatible = "fsl,ls1021a-scfg"; - reg = <0x0 0x1570000 0x0 0x10000>; - }; - -Freescale DCFG - DCFG is the device configuration unit, that provides general purpose -configuration and status for the device. Such as setting the secondary -core start address and release the secondary core from holdoff and startup. - Required properties: - - compatible: Should contain a chip-specific compatible string, - Chip-specific strings are of the form "fsl,<chip>-dcfg", - The following <chip>s are known to be supported: - ls1012a, ls1021a, ls1043a, ls1046a, ls2080a. - - - reg : should contain base address and length of DCFG memory-mapped registers - -Example: - dcfg: dcfg@1ee0000 { - compatible = "fsl,ls1021a-dcfg"; - reg = <0x0 0x1ee0000 0x0 0x10000>; - }; - Freescale ARMv8 based Layerscape SoC family Device Tree Bindings ---------------------------------------------------------------- diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index 199cd36fe1ba..a97f643e7d1c 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -8,6 +8,14 @@ HiKey960 Board Required root node properties: - compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660"; +Hi3670 SoC +Required root node properties: + - compatible = "hisilicon,hi3670"; + +HiKey970 Board +Required root node properties: + - compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670"; + Hi3798cv200 SoC Required root node properties: - compatible = "hisilicon,hi3798cv200"; diff --git a/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt index 31f5f9a104cc..b56a02c10ae6 100644 --- a/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt +++ b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt @@ -45,11 +45,15 @@ Optional Properties: debug_messages - Map the Debug message region - reg: register space corresponding to the debug_messages - ti,system-reboot-controller: If system reboot can be triggered by SoC reboot +- ti,host-id: Integer value corresponding to the host ID assigned by Firmware + for identification of host processing entities such as virtual + machines Example (K2G): ------------- pmmc: pmmc { compatible = "ti,k2g-sci"; + ti,host-id = <2>; mbox-names = "rx", "tx"; mboxes= <&msgmgr &msgmgr_proxy_pmmc_rx>, <&msgmgr &msgmgr_proxy_pmmc_tx>; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt index b404d592ce58..4e4a3c0ab9ab 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt @@ -10,6 +10,7 @@ Required Properties: - "mediatek,mt2712-apmixedsys", "syscon" - "mediatek,mt6797-apmixedsys" - "mediatek,mt7622-apmixedsys" + - "mediatek,mt7623-apmixedsys", "mediatek,mt2701-apmixedsys" - "mediatek,mt8135-apmixedsys" - "mediatek,mt8173-apmixedsys" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index 34a69ba67f13..d1606b2c3e63 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2701-audsys", "syscon" - "mediatek,mt7622-audsys", "syscon" + - "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon" - #clock-cells: Must be 1 The AUDSYS controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt index 4010e37c53a0..149567a38215 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt2701-bdpsys", "syscon" - "mediatek,mt2712-bdpsys", "syscon" + - "mediatek,mt7623-bdpsys", "mediatek,mt2701-bdpsys", "syscon" - #clock-cells: Must be 1 The bdpsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt index 8f5335b480ac..f17cfe64255d 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt @@ -8,6 +8,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt2701-ethsys", "syscon" - "mediatek,mt7622-ethsys", "syscon" + - "mediatek,mt7623-ethsys", "mediatek,mt2701-ethsys", "syscon" - #clock-cells: Must be 1 - #reset-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt index f5629d64cef2..323905af82c3 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt @@ -9,6 +9,7 @@ Required Properties: - compatible: Should be: - "mediatek,mt2701-hifsys", "syscon" - "mediatek,mt7622-hifsys", "syscon" + - "mediatek,mt7623-hifsys", "mediatek,mt2701-hifsys", "syscon" - #clock-cells: Must be 1 The hifsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt index 868bd51a98be..3f99672163e3 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt2712-imgsys", "syscon" - "mediatek,mt6797-imgsys", "syscon" + - "mediatek,mt7623-imgsys", "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt8173-imgsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index 566f153f9f83..89f4272a1441 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -11,6 +11,7 @@ Required Properties: - "mediatek,mt2712-infracfg", "syscon" - "mediatek,mt6797-infracfg", "syscon" - "mediatek,mt7622-infracfg", "syscon" + - "mediatek,mt7623-infracfg", "mediatek,mt2701-infracfg", "syscon" - "mediatek,mt8135-infracfg", "syscon" - "mediatek,mt8173-infracfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt index 4eb8bbe15c01..15d977afad31 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt2712-mmsys", "syscon" - "mediatek,mt6797-mmsys", "syscon" + - "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt8173-mmsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt index fb58ca8c2770..6755514deb80 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt @@ -10,6 +10,7 @@ Required Properties: - "mediatek,mt2701-pericfg", "syscon" - "mediatek,mt2712-pericfg", "syscon" - "mediatek,mt7622-pericfg", "syscon" + - "mediatek,mt7623-pericfg", "mediatek,mt2701-pericfg", "syscon" - "mediatek,mt8135-pericfg", "syscon" - "mediatek,mt8173-pericfg", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt index 24014a7e2332..d849465b8c99 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt @@ -10,6 +10,7 @@ Required Properties: - "mediatek,mt2712-topckgen", "syscon" - "mediatek,mt6797-topckgen" - "mediatek,mt7622-topckgen" + - "mediatek,mt7623-topckgen", "mediatek,mt2701-topckgen" - "mediatek,mt8135-topckgen" - "mediatek,mt8173-topckgen" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt index ea40d05089f8..3212afc753c8 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt2712-vdecsys", "syscon" - "mediatek,mt6797-vdecsys", "syscon" + - "mediatek,mt7623-vdecsys", "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt8173-vdecsys", "syscon" - #clock-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.txt index 5e85749262ae..eaee06b2d8f2 100644 --- a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.txt +++ b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.txt @@ -16,11 +16,26 @@ Properties: - reg: Usage: required Value Type: <prop-encoded-array> - Definition: Start address and the the size of the register region. + Definition: The first element specifies the llcc base start address and + the size of the register region. The second element specifies + the llcc broadcast base address and size of the register region. + +- reg-names: + Usage: required + Value Type: <stringlist> + Definition: Register region names. Must be "llcc_base", "llcc_broadcast_base". + +- interrupts: + Usage: required + Definition: The interrupt is associated with the llcc edac device. + It's used for llcc cache single and double bit error detection + and reporting. Example: cache-controller@1100000 { compatible = "qcom,sdm845-llcc"; - reg = <0x1100000 0x250000>; + reg = <0x1100000 0x200000>, <0x1300000 0x50000> ; + reg-names = "llcc_base", "llcc_broadcast_base"; + interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index acfd3c773dd0..0cc71236d639 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -5,6 +5,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "vamrs,ficus", "rockchip,rk3399"; +- 96boards RK3399 Rock960 (ROCK960 Consumer Edition) + Required root node properties: + - compatible = "vamrs,rock960", "rockchip,rk3399"; + - Amarula Vyasa RK3288 board Required root node properties: - compatible = "amarula,vyasa-rk3288", "rockchip,rk3288"; @@ -13,6 +17,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "asus,rk3288-tinker", "rockchip,rk3288"; +- Asus Tinker board S + Required root node properties: + - compatible = "asus,rk3288-tinker-s", "rockchip,rk3288"; + - Kylin RK3036 board: Required root node properties: - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036"; @@ -59,6 +67,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328"; +- Firefly ROC-RK3399-PC board: + Required root node properties: + - compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399"; + - ChipSPARK PopMetal-RK3288 board: Required root node properties: - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; @@ -160,6 +172,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "pine64,rock64", "rockchip,rk3328"; +- Pine64 RockPro64 board: + Required root node properties: + - compatible = "pine64,rockpro64", "rockchip,rk3399"; + - Rockchip PX3 Evaluation board: Required root node properties: - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188"; @@ -168,6 +184,10 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368"; +- Rockchip PX30 Evaluation board: + Required root node properties: + - compatible = "rockchip,px30-evb", "rockchip,px30"; + - Rockchip RV1108 Evaluation board Required root node properties: - compatible = "rockchip,rv1108-evb", "rockchip,rv1108"; diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt index 08a587875996..74d0a780ce51 100644 --- a/Documentation/devicetree/bindings/arm/scu.txt +++ b/Documentation/devicetree/bindings/arm/scu.txt @@ -22,7 +22,7 @@ References: Example: -scu@a04100000 { +scu@a0410000 { compatible = "arm,cortex-a9-scu"; reg = <0xa0410000 0x100>; }; diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt index e31303fb233a..f27bbff2c780 100644 --- a/Documentation/devicetree/bindings/arm/secure.txt +++ b/Documentation/devicetree/bindings/arm/secure.txt @@ -32,7 +32,8 @@ describe the view of Secure world using the standard bindings. These secure- bindings only need to be used where both the Secure and Normal world views need to be described in a single device tree. -Valid Secure world properties: +Valid Secure world properties +----------------------------- - secure-status : specifies whether the device is present and usable in the secure world. The combination of this with "status" allows @@ -51,3 +52,19 @@ Valid Secure world properties: status = "disabled"; secure-status = "okay"; /* S-only */ status = "disabled"; /* disabled in both */ status = "disabled"; secure-status = "disabled"; /* disabled in both */ + +The secure-chosen node +---------------------- + +Similar to the /chosen node which serves as a place for passing data +between firmware and the operating system, the /secure-chosen node may +be used to pass data to the Secure OS. Only the properties defined +below may appear in the /secure-chosen node. + +- stdout-path : specifies the device to be used by the Secure OS for + its console output. The syntax is the same as for /chosen/stdout-path. + If the /secure-chosen node exists but the stdout-path property is not + present, the Secure OS should not perform any console output. If + /secure-chosen does not exist, the Secure OS should use the value of + /chosen/stdout-path instead (that is, use the same device as the + Normal world OS). diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 89b4a389fbc7..f5e0f82fd503 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -7,6 +7,8 @@ SoCs: compatible = "renesas,emev2" - RZ/A1H (R7S72100) compatible = "renesas,r7s72100" + - RZ/A2 (R7S9210) + compatible = "renesas,r7s9210" - SH-Mobile AG5 (R8A73A00/SH73A0) compatible = "renesas,sh73a0" - R-Mobile APE6 (R8A73A40) @@ -23,6 +25,10 @@ SoCs: compatible = "renesas,r8a7745" - RZ/G1C (R8A77470) compatible = "renesas,r8a77470" + - RZ/G2M (R8A774A1) + compatible = "renesas,r8a774a1" + - RZ/G2E (RA8774C0) + compatible = "renesas,r8a774c0" - R-Car M1A (R8A77781) compatible = "renesas,r8a7778" - R-Car H1 (R8A77790) @@ -107,6 +113,8 @@ Boards: compatible = "renesas,lager", "renesas,r8a7790" - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0)) compatible = "renesas,m3ulcb", "renesas,r8a7796" + - M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1)) + compatible = "renesas,m3nulcb", "renesas,r8a77965" - Marzen (R0P7779A00010S) compatible = "renesas,marzen", "renesas,r8a7779" - Porter (M2-LCDP) @@ -143,12 +151,12 @@ Boards: compatible = "renesas,wheat", "renesas,r8a7792" -Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC -product and revision information. If present, a device node for this register -should be added. +Most Renesas ARM SoCs have a Product Register or Boundary Scan ID Register that +allows to retrieve SoC product and revision information. If present, a device +node for this register should be added. Required properties: - - compatible: Must be "renesas,prr". + - compatible: Must be "renesas,prr" or "renesas,bsid" - reg: Base address and length of the register block. diff --git a/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/syna.txt index 3bab18409b7a..2face46a5f64 100644 --- a/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt +++ b/Documentation/devicetree/bindings/arm/syna.txt @@ -1,4 +1,9 @@ -Marvell Berlin SoC Family Device Tree Bindings +Synaptics SoC Device Tree Bindings + +According to https://www.synaptics.com/company/news/conexant-marvell +Synaptics has acquired the Multimedia Solutions Business of Marvell, so +berlin SoCs are now Synaptics' SoCs now. + --------------------------------------------------------------- Work in progress statement: @@ -13,6 +18,10 @@ stable binding/ABI. --------------------------------------------------------------- +Boards with the Synaptics AS370 SoC shall have the following properties: + Required root node property: + compatible: "syna,as370" + Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500 shall have the following properties: diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index 32f62bb7006d..c59b15f64346 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -47,12 +47,17 @@ board-specific compatible values: nvidia,ventana toradex,apalis_t30 toradex,apalis_t30-eval + toradex,apalis_t30-v1.1 + toradex,apalis_t30-v1.1-eval toradex,apalis-tk1 toradex,apalis-tk1-eval - toradex,colibri_t20-512 + toradex,apalis-tk1-v1.2 + toradex,apalis-tk1-v1.2-eval + toradex,colibri_t20 + toradex,colibri_t20-eval-v3 + toradex,colibri_t20-iris toradex,colibri_t30 toradex,colibri_t30-eval-v3 - toradex,iris Trusted Foundations ------------------------------------------- diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt index 5a3bf7c5a7a0..c9fd6d1de57e 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt @@ -34,3 +34,96 @@ Board DTS: pmc@c360000 { nvidia,invert-interrupt; }; + +== Pad Control == + +On Tegra SoCs a pad is a set of pins which are configured as a group. +The pin grouping is a fixed attribute of the hardware. The PMC can be +used to set pad power state and signaling voltage. A pad can be either +in active or power down mode. The support for power state and signaling +voltage configuration varies depending on the pad in question. 3.3 V and +1.8 V signaling voltages are supported on pins where software +controllable signaling voltage switching is available. + +Pad configurations are described with pin configuration nodes which +are placed under the pmc node and they are referred to by the pinctrl +client properties. For more information see +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt. + +The following pads are present on Tegra186: +csia csib dsi mipi-bias +pex-clk-bias pex-clk3 pex-clk2 pex-clk1 +usb0 usb1 usb2 usb-bias +uart audio hsic dbg +hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv +sdmmc4 cam dsib dsic +dsid csic csid csie +dsif spi ufs dmic-hv +edp sdmmc1-hv sdmmc3-hv conn +audio-hv ao-hv + +Required pin configuration properties: + - pins: A list of strings, each of which contains the name of a pad + to be configured. + +Optional pin configuration properties: + - low-power-enable: Configure the pad into power down mode + - low-power-disable: Configure the pad into active mode + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + +Note: The power state can be configured on all of the above pads except + for ao-hv. Following pads have software configurable signaling + voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv, + ao-hv. + +Pad configuration state example: + pmc: pmc@7000e400 { + compatible = "nvidia,tegra186-pmc"; + reg = <0 0x0c360000 0 0x10000>, + <0 0x0c370000 0 0x10000>, + <0 0x0c380000 0 0x10000>, + <0 0x0c390000 0 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + + ... + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + hdmi_off: hdmi-off { + pins = "hdmi"; + low-power-enable; + } + + hdmi_on: hdmi-on { + pins = "hdmi"; + low-power-disable; + } + }; + +Pinctrl client example: + sdmmc1: sdhci@3400000 { + ... + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; + + ... + + sor0: sor@15540000 { + ... + pinctrl-0 = <&hdmi_off>; + pinctrl-1 = <&hdmi_on>; + pinctrl-names = "hdmi-on", "hdmi-off"; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index a74b37b07e5c..cb12f33a247f 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -195,3 +195,106 @@ Example: power-domains = <&pd_audio>; ... }; + +== Pad Control == + +On Tegra SoCs a pad is a set of pins which are configured as a group. +The pin grouping is a fixed attribute of the hardware. The PMC can be +used to set pad power state and signaling voltage. A pad can be either +in active or power down mode. The support for power state and signaling +voltage configuration varies depending on the pad in question. 3.3 V and +1.8 V signaling voltages are supported on pins where software +controllable signaling voltage switching is available. + +The pad configuration state nodes are placed under the pmc node and they +are referred to by the pinctrl client properties. For more information +see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt. +The pad name should be used as the value of the pins property in pin +configuration nodes. + +The following pads are present on Tegra124 and Tegra132: +audio bb cam comp +csia csb cse dsi +dsib dsic dsid hdmi +hsic hv lvds mipi-bias +nand pex-bias pex-clk1 pex-clk2 +pex-cntrl sdmmc1 sdmmc3 sdmmc4 +sys_ddc uart usb0 usb1 +usb2 usb_bias + +The following pads are present on Tegra210: +audio audio-hv cam csia +csib csic csid csie +csif dbg debug-nonao dmic +dp dsi dsib dsic +dsid emmc emmc2 gpio +hdmi hsic lvds mipi-bias +pex-bias pex-clk1 pex-clk2 pex-cntrl +sdmmc1 sdmmc3 spi spi-hv +uart usb0 usb1 usb2 +usb3 usb-bias + +Required pin configuration properties: + - pins: Must contain name of the pad(s) to be configured. + +Optional pin configuration properties: + - low-power-enable: Configure the pad into power down mode + - low-power-disable: Configure the pad into active mode + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 + or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + +Note: The power state can be configured on all of the Tegra124 and + Tegra132 pads. None of the Tegra124 or Tegra132 pads support + signaling voltage switching. + +Note: All of the listed Tegra210 pads except pex-cntrl support power + state configuration. Signaling voltage switching is supported on + following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio, + pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart. + +Pad configuration state example: + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + + ... + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + hdmi_off: hdmi-off { + pins = "hdmi"; + low-power-enable; + } + + hdmi_on: hdmi-on { + pins = "hdmi"; + low-power-disable; + } + }; + +Pinctrl client example: + sdmmc1: sdhci@700b0000 { + ... + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; + ... + sor@54540000 { + ... + pinctrl-0 = <&hdmi_off>; + pinctrl-1 = <&hdmi_on>; + pinctrl-names = "hdmi-on", "hdmi-off"; + }; diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt index 0fa429534f49..89408de55bfd 100644 --- a/Documentation/devicetree/bindings/arm/ux500/boards.txt +++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt @@ -60,7 +60,7 @@ Example: <0xa0410100 0x100>; }; - scu@a04100000 { + scu@a0410000 { compatible = "arm,cortex-a9-scu"; reg = <0xa0410000 0x100>; }; diff --git a/Documentation/devicetree/bindings/arm/zte,sysctrl.txt b/Documentation/devicetree/bindings/arm/zte,sysctrl.txt new file mode 100644 index 000000000000..7e66b7f7ba96 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/zte,sysctrl.txt @@ -0,0 +1,30 @@ +ZTE sysctrl Registers + +Registers for 'zte,zx296702' SoC: + +System management required properties: + - compatible = "zte,sysctrl" + +Low power management required properties: + - compatible = "zte,zx296702-pcu" + +Bus matrix required properties: + - compatible = "zte,zx-bus-matrix" + + +Registers for 'zte,zx296718' SoC: + +System management required properties: + - compatible = "zte,zx296718-aon-sysctrl" + - compatible = "zte,zx296718-sysctrl" + +Example: +aon_sysctrl: aon-sysctrl@116000 { + compatible = "zte,zx296718-aon-sysctrl", "syscon"; + reg = <0x116000 0x1000>; +}; + +sysctrl: sysctrl@1463000 { + compatible = "zte,zx296718-sysctrl", "syscon"; + reg = <0x1463000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/arm/zte.txt b/Documentation/devicetree/bindings/arm/zte.txt index 83369785d29c..340612794a37 100644 --- a/Documentation/devicetree/bindings/arm/zte.txt +++ b/Documentation/devicetree/bindings/arm/zte.txt @@ -1,20 +1,10 @@ ZTE platforms device tree bindings ---------------------------------------- +--------------------------------------- - ZX296702 board: Required root node properties: - compatible = "zte,zx296702-ad1", "zte,zx296702" -System management required properties: - - compatible = "zte,sysctrl" - -Low power management required properties: - - compatible = "zte,zx296702-pcu" - -Bus matrix required properties: - - compatible = "zte,zx-bus-matrix" - - --------------------------------------- - ZX296718 SoC: Required root node properties: @@ -22,18 +12,3 @@ Bus matrix required properties: ZX296718 EVB board: - "zte,zx296718-evb" - -System management required properties: - - compatible = "zte,zx296718-aon-sysctrl" - - compatible = "zte,zx296718-sysctrl" - -Example: -aon_sysctrl: aon-sysctrl@116000 { - compatible = "zte,zx296718-aon-sysctrl", "syscon"; - reg = <0x116000 0x1000>; -}; - -sysctrl: sysctrl@1463000 { - compatible = "zte,zx296718-sysctrl", "syscon"; - reg = <0x1463000 0x1000>; -}; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 5d5bd456d9d9..e30fd106df4f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -10,6 +10,7 @@ PHYs. Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" + - "allwinner,sun8i-r40-ahci" - "brcm,iproc-ahci" - "hisilicon,hisi-ahci" - "cavium,octeon-7130-ahci" @@ -31,8 +32,10 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power +- phy-supply : regulator for PHY power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" +- ahci-supply : regulator for AHCI controller - ports-implemented : Mask that indicates which ports that the HBA supports are available for software to use. Useful if PORTS_IMPL is not programmed by the BIOS, which is true with @@ -42,12 +45,13 @@ Required properties when using sub-nodes: - #address-cells : number of cells to encode an address - #size-cells : number of cells representing the size of an address +For allwinner,sun8i-r40-ahci, the reset propertie must be present. Sub-nodes required properties: - reg : the port number And at least one of the following properties: - phys : reference to the SATA PHY node -- target-supply : regulator for SATA target power +- target-supply : regulator for SATA target power Examples: sata@ffe08000 { diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 0a5b3b47f217..7713a413c6a7 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -9,6 +9,7 @@ Required properties: "brcm,bcm7445-ahci" "brcm,bcm-nsp-ahci" "brcm,sata3-ahci" + "brcm,bcm63138-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index a45ca67a9d5f..e1308346e00d 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -6,6 +6,14 @@ Required properties: - interrupts: Should contain CCM interrupt - #clock-cells: Should be <1> +Optional properties: +- fsl,pmic-stby-poweroff: Configure CCM to assert PMIC_STBY_REQ signal + on power off. + Use this property if the SoC should be powered off by external power + management IC (PMIC) triggered via PMIC_STBY_REQ signal. + Boards that are designed to initiate poweroff on PMIC_ON_REQ signal should + be using "syscon-poweroff" driver instead. + The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6qdl-clock.h for the full list of i.MX6 Quad and DualLite clock IDs. diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt index 8855bfcfd778..d90e17e2428b 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.txt +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt @@ -29,15 +29,15 @@ Required properties for usb-c-connector with power delivery support: in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 Source_Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power source and power dual role. - User can specify the source PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() + defined in dt-bindings/usb/pd.h. - sink-pdos: An array of u32 with each entry providing supported power sink data object(PDO), the detailed bit definitions of PDO can be found in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 Sink Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power sink and power dual role. - User can specify the sink PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined + in dt-bindings/usb/pd.h. - op-sink-microwatt: Sink required operating power in microwatt, if source can't offer the power, Capability Mismatch is set. Required for power sink and power dual role. diff --git a/Documentation/devicetree/bindings/crypto/hisilicon,hip07-sec.txt b/Documentation/devicetree/bindings/crypto/hisilicon,hip07-sec.txt index 78d2db9d4de5..d28fd1af01b4 100644 --- a/Documentation/devicetree/bindings/crypto/hisilicon,hip07-sec.txt +++ b/Documentation/devicetree/bindings/crypto/hisilicon,hip07-sec.txt @@ -24,7 +24,7 @@ Optional properties: Example: -p1_sec_a: crypto@400,d2000000 { +p1_sec_a: crypto@400d2000000 { compatible = "hisilicon,hip07-sec"; reg = <0x400 0xd0000000 0x0 0x10000 0x400 0xd2000000 0x0 0x10000 diff --git a/Documentation/devicetree/bindings/csky/cpus.txt b/Documentation/devicetree/bindings/csky/cpus.txt new file mode 100644 index 000000000000..ae79412f2680 --- /dev/null +++ b/Documentation/devicetree/bindings/csky/cpus.txt @@ -0,0 +1,73 @@ +================== +C-SKY CPU Bindings +================== + +The device tree allows to describe the layout of CPUs in a system through +the "cpus" node, which in turn contains a number of subnodes (ie "cpu") +defining properties for every cpu. + +Only SMP system need to care about the cpus node and single processor +needn't define cpus node at all. + +===================================== +cpus and cpu node bindings definition +===================================== + +- cpus node + + Description: Container of cpu nodes + + The node name must be "cpus". + + A cpus node must define the following properties: + + - #address-cells + Usage: required + Value type: <u32> + Definition: must be set to 1 + - #size-cells + Usage: required + Value type: <u32> + Definition: must be set to 0 + +- cpu node + + Description: Describes one of SMP cores + + PROPERTIES + + - device_type + Usage: required + Value type: <string> + Definition: must be "cpu" + - reg + Usage: required + Value type: <u32> + Definition: CPU index + - compatible: + Usage: required + Value type: <string> + Definition: must contain "csky", eg: + "csky,610" + "csky,807" + "csky,810" + "csky,860" + +Example: +-------- + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + reg = <0>; + status = "ok"; + }; + + cpu@1 { + device_type = "cpu"; + reg = <1>; + status = "ok"; + }; + }; diff --git a/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt index 82f2acb3d374..0398aec488ac 100644 --- a/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt +++ b/Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt @@ -15,6 +15,13 @@ Required children nodes: to external devices using the OF graph reprensentation (see ../graph.txt). At least one port node is required. +Optional properties in grandchild nodes: + Any endpoint grandchild node may specify a desired video interface + according to ../../media/video-interfaces.txt, specifically + - bus-width: recognized values are <12>, <16>, <18> and <24>, and + override any output mode selection heuristic, forcing "rgb444", + "rgb565", "rgb666" and "rgb888" respectively. + Example: hlcdc: hlcdc@f0030000 { @@ -50,3 +57,19 @@ Example: #pwm-cells = <3>; }; }; + +Example 2: With a video interface override to force rgb565; as above +but with these changes/additions: + + &hlcdc { + hlcdc-display-controller { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb565>; + + port@0 { + hlcdc_panel_output: endpoint@0 { + bus-width = <16>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt index fd39ad34c383..50220190c203 100644 --- a/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt +++ b/Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt @@ -22,7 +22,13 @@ among others. Required properties: -- compatible: Must be "lvds-encoder" +- compatible: Must be one or more of the following + - "ti,ds90c185" for the TI DS90C185 FPD-Link Serializer + - "lvds-encoder" for a generic LVDS encoder device + + When compatible with the generic version, nodes must list the + device-specific version corresponding to the device first + followed by the generic version. Required nodes: diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt index 4f0ab3ed3b6f..3aeb0ec06fd0 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt @@ -14,10 +14,22 @@ Required properties: - "renesas,r8a7795-lvds" for R8A7795 (R-Car H3) compatible LVDS encoders - "renesas,r8a7796-lvds" for R8A7796 (R-Car M3-W) compatible LVDS encoders - "renesas,r8a77970-lvds" for R8A77970 (R-Car V3M) compatible LVDS encoders + - "renesas,r8a77980-lvds" for R8A77980 (R-Car V3H) compatible LVDS encoders + - "renesas,r8a77990-lvds" for R8A77990 (R-Car E3) compatible LVDS encoders - "renesas,r8a77995-lvds" for R8A77995 (R-Car D3) compatible LVDS encoders - reg: Base address and length for the memory-mapped registers -- clocks: A phandle + clock-specifier pair for the functional clock +- clocks: A list of phandles + clock-specifier pairs, one for each entry in + the clock-names property. +- clock-names: Name of the clocks. This property is model-dependent. + - The functional clock, which mandatory for all models, shall be listed + first, and shall be named "fck". + - On R8A77990 and R8A77995, the LVDS encoder can use the EXTAL or + DU_DOTCLKINx clocks. Those clocks are optional. When supplied they must be + named "extal" and "dclkin.x" respectively, with "x" being the DU_DOTCLKIN + numerical index. + - When the clocks property only contains the functional clock, the + clock-names property may be omitted. - resets: A phandle + reset specifier for the module reset Required nodes: diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt new file mode 100644 index 000000000000..0a3fbb53a16e --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt @@ -0,0 +1,87 @@ +SN65DSI86 DSI to eDP bridge chip +-------------------------------- + +This is the binding for Texas Instruments SN65DSI86 bridge. +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +Required properties: +- compatible: Must be "ti,sn65dsi86" +- reg: i2c address of the chip, 0x2d as per datasheet +- enable-gpios: gpio specification for bridge_en pin (active high) + +- vccio-supply: A 1.8V supply that powers up the digital IOs. +- vpll-supply: A 1.8V supply that powers up the displayport PLL. +- vcca-supply: A 1.2V supply that powers up the analog circuits. +- vcc-supply: A 1.2V supply that powers up the digital core. + +Optional properties: +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. + +- gpio-controller: Marks the device has a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../../gpio/gpio.txt for more information. +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of + the cell formats. + +- clock-names: should be "refclk" +- clocks: Specification for input reference clock. The reference + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. + +- data-lanes: See ../../media/video-interface.txt +- lane-polarities: See ../../media/video-interface.txt + +- suspend-gpios: specification for GPIO1 pin on bridge (active low) + +Required nodes: +This device has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DSI input +- Video port 1 for eDP output + +Example +------- + +edp-bridge@2d { + compatible = "ti,sn65dsi86"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2d>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; + + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; + + vccio-supply = <&pm8916_l17>; + vcca-supply = <&pm8916_l6>; + vpll-supply = <&pm8916_l17>; + vcc-supply = <&pm8916_l6>; + + clock-names = "refclk"; + clocks = <&input_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + data-lanes = <2 1 3 0>; + lane-polarities = <0 1 0 1>; + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +} diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new file mode 100644 index 000000000000..8f9abf28a8fa --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt @@ -0,0 +1,35 @@ +TC358764 MIPI-DSI to LVDS panel bridge + +Required properties: + - compatible: "toshiba,tc358764" + - reg: the virtual channel number of a DSI peripheral + - vddc-supply: core voltage supply, 1.2V + - vddio-supply: I/O voltage supply, 1.8V or 3.3V + - vddlvds-supply: LVDS1/2 voltage supply, 3.3V + - reset-gpios: a GPIO spec for the reset pin + +The device node can contain following 'port' child nodes, +according to the OF graph bindings defined in [1]: + 0: DSI Input, not required, if the bridge is DSI controlled + 1: LVDS Output, mandatory + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + bridge@0 { + reg = <0>; + compatible = "toshiba,tc358764"; + vddc-supply = <&vcc_1v2_reg>; + vddio-supply = <&vcc_1v8_reg>; + vddlvds-supply = <&vcc_3v3_reg>; + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + port@1 { + reg = <1>; + lvds_ep: endpoint { + remote-endpoint = <&panel_ep>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 2fff8b406f4c..be377786e8cd 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -21,6 +21,9 @@ Required properties: - samsung,pll-clock-frequency: specifies frequency of the oscillator clock - #address-cells, #size-cells: should be set respectively to <1> and <0> according to DSI host bindings (see MIPI DSI bindings [1]) + - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst + mode + - samsung,esc-clock-frequency: specifies DSI frequency in escape mode Optional properties: - power-domains: a phandle to DSIM power domain node @@ -29,25 +32,9 @@ Child nodes: Should contain DSI peripheral nodes (see MIPI DSI bindings [1]). Video interfaces: - Device node can contain video interface port nodes according to [2]. - The following are properties specific to those nodes: - - port node inbound: - - reg: (required) must be 0. - port node outbound: - - reg: (required) must be 1. - - endpoint node connected from mic node (reg = 0): - - remote-endpoint: specifies the endpoint in mic node. This node is required - for Exynos5433 mipi dsi. So mic can access to panel node - throughout this dsi node. - endpoint node connected to panel node (reg = 1): - - remote-endpoint: specifies the endpoint in panel node. This node is - required in all kinds of exynos mipi dsi to represent - the connection between mipi dsi and panel. - - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst - mode - - samsung,esc-clock-frequency: specifies DSI frequency in escape mode + Device node can contain following video interface port nodes according to [2]: + 0: RGB input, + 1: DSI output [1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt [2]: Documentation/devicetree/bindings/media/video-interfaces.txt diff --git a/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt index 973c27273772..a336599f6c03 100644 --- a/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt +++ b/Documentation/devicetree/bindings/display/mipi-dsi-bus.txt @@ -16,7 +16,7 @@ The following assumes that only a single peripheral is connected to a DSI host. Experience shows that this is true for the large majority of setups. DSI host --------- +======== In addition to the standard properties and those defined by the parent bus of a DSI host, the following properties apply to a node representing a DSI host. @@ -29,12 +29,24 @@ Required properties: - #size-cells: Should be 0. There are cases where it makes sense to use a different value here. See below. +Optional properties: +- clock-master: boolean. Should be enabled if the host is being used in + conjunction with another DSI host to drive the same peripheral. Hardware + supporting such a configuration generally requires the data on both the busses + to be driven by the same clock. Only the DSI host instance controlling this + clock should contain this property. + DSI peripheral --------------- +============== + +Peripherals with DSI as control bus, or no control bus +------------------------------------------------------ -Peripherals are represented as child nodes of the DSI host's node. Properties -described here apply to all DSI peripherals, but individual bindings may want -to define additional, device-specific properties. +Peripherals with the DSI bus as the primary control bus, or peripherals with +no control bus but use the DSI bus to transmit pixel data are represented +as child nodes of the DSI host's node. Properties described here apply to all +DSI peripherals, but individual bindings may want to define additional, +device-specific properties. Required properties: - reg: The virtual channel number of a DSI peripheral. Must be in the range @@ -49,9 +61,37 @@ case two alternative representations can be chosen: property is the number of the first virtual channel and the second cell is the number of consecutive virtual channels. -Example -------- - +Peripherals with a different control bus +---------------------------------------- + +There are peripherals that have I2C/SPI (or some other non-DSI bus) as the +primary control bus, but are also connected to a DSI bus (mostly for the data +path). Connections between such peripherals and a DSI host can be represented +using the graph bindings [1], [2]. + +Peripherals that support dual channel DSI +----------------------------------------- + +Peripherals with higher bandwidth requirements can be connected to 2 DSI +busses. Each DSI bus/channel drives some portion of the pixel data (generally +left/right half of each line of the display, or even/odd lines of the display). +The graph bindings should be used to represent the multiple DSI busses that are +connected to this peripheral. Each DSI host's output endpoint can be linked to +an input endpoint of the DSI peripheral. + +[1] Documentation/devicetree/bindings/graph.txt +[2] Documentation/devicetree/bindings/media/video-interfaces.txt + +Examples +======== +- (1), (2) and (3) are examples of a DSI host and peripheral on the DSI bus + with different virtual channel configurations. +- (4) is an example of a peripheral on a I2C control bus connected to a + DSI host using of-graph bindings. +- (5) is an example of 2 DSI hosts driving a dual-channel DSI peripheral, + which uses I2C as its primary control bus. + +1) dsi-host { ... @@ -67,6 +107,7 @@ Example ... }; +2) dsi-host { ... @@ -82,6 +123,7 @@ Example ... }; +3) dsi-host { ... @@ -96,3 +138,98 @@ Example ... }; + +4) + i2c-host { + ... + + dsi-bridge@35 { + compatible = "..."; + reg = <0x35>; + + ports { + ... + + port { + bridge_mipi_in: endpoint { + remote-endpoint = <&host_mipi_out>; + }; + }; + }; + }; + }; + + dsi-host { + ... + + ports { + ... + + port { + host_mipi_out: endpoint { + remote-endpoint = <&bridge_mipi_in>; + }; + }; + }; + }; + +5) + i2c-host { + dsi-bridge@35 { + compatible = "..."; + reg = <0x35>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + dsi1_in: endpoint { + remote-endpoint = <&dsi1_out>; + }; + }; + }; + }; + }; + + dsi0-host { + ... + + /* + * this DSI instance drives the clock for both the host + * controllers + */ + clock-master; + + ports { + ... + + port { + dsi0_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi1-host { + ... + + ports { + ... + + port { + dsi1_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index ec9d34be2ff7..9de67be632d1 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -15,6 +15,8 @@ Required Properties: - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU - "renesas,du-r8a77965" for R8A77965 (R-Car M3-N) compatible DU - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU + - "renesas,du-r8a77980" for R8A77980 (R-Car V3H) compatible DU + - "renesas,du-r8a77990" for R8A77990 (R-Car E3) compatible DU - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU - reg: the memory-mapped I/O registers base address and length @@ -61,6 +63,8 @@ corresponding to each DU output. R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - R8A77965 (R-Car M3-N) DPAD 0 HDMI 0 LVDS 0 - R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - + R8A77980 (R-Car V3H) DPAD 0 LVDS 0 - - + R8A77990 (R-Car E3) DPAD 0 LVDS 0 LVDS 1 - R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt index eeda3597011e..b79e5769f0ae 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt @@ -8,6 +8,9 @@ Required properties: - compatible: value should be one of the following "rockchip,rk3036-vop"; "rockchip,rk3126-vop"; + "rockchip,px30-vop-lit"; + "rockchip,px30-vop-big"; + "rockchip,rk3188-vop"; "rockchip,rk3288-vop"; "rockchip,rk3368-vop"; "rockchip,rk3366-vop"; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index f8773ecb7525..7854fff4fc16 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -78,6 +78,7 @@ Required properties: - compatible: value must be one of: * "allwinner,sun8i-a83t-dw-hdmi" + * "allwinner,sun50i-a64-dw-hdmi", "allwinner,sun8i-a83t-dw-hdmi" - reg: base address and size of memory-mapped region - reg-io-width: See dw_hdmi.txt. Shall be 1. - interrupts: HDMI interrupt number @@ -96,6 +97,9 @@ Required properties: first port should be the input endpoint. The second should be the output, usually to an HDMI connector. +Optional properties: + - hvcc-supply: the VCC power supply of the controller + DWC HDMI PHY ------------ @@ -103,6 +107,7 @@ Required properties: - compatible: value must be one of: * allwinner,sun8i-a83t-hdmi-phy * allwinner,sun8i-h3-hdmi-phy + * allwinner,sun8i-r40-hdmi-phy * allwinner,sun50i-a64-hdmi-phy - reg: base address and size of memory-mapped region - clocks: phandles to the clocks feeding the HDMI PHY @@ -112,9 +117,9 @@ Required properties: - resets: phandle to the reset controller driving the PHY - reset-names: must be "phy" -H3 and A64 HDMI PHY require additional clocks: +H3, A64 and R40 HDMI PHY require additional clocks: - pll-0: parent of phy clock - - pll-1: second possible phy clock parent (A64 only) + - pll-1: second possible phy clock parent (A64/R40 only) TV Encoder ---------- @@ -151,6 +156,8 @@ Required properties: * allwinner,sun8i-v3s-tcon * allwinner,sun9i-a80-tcon-lcd * allwinner,sun9i-a80-tcon-tv + * "allwinner,sun50i-a64-tcon-lcd", "allwinner,sun8i-a83t-tcon-lcd" + * "allwinner,sun50i-a64-tcon-tv", "allwinner,sun8i-a83t-tcon-tv" - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the TCON. @@ -369,7 +376,11 @@ Required properties: * allwinner,sun8i-a83t-de2-mixer-0 * allwinner,sun8i-a83t-de2-mixer-1 * allwinner,sun8i-h3-de2-mixer-0 + * allwinner,sun8i-r40-de2-mixer-0 + * allwinner,sun8i-r40-de2-mixer-1 * allwinner,sun8i-v3s-de2-mixer + * allwinner,sun50i-a64-de2-mixer-0 + * allwinner,sun50i-a64-de2-mixer-1 - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the mixer * bus: the mixer interface clock @@ -403,6 +414,7 @@ Required properties: * allwinner,sun8i-r40-display-engine * allwinner,sun8i-v3s-display-engine * allwinner,sun9i-a80-display-engine + * allwinner,sun50i-a64-display-engine - allwinner,pipelines: list of phandle to the display engine frontends (DE 1.0) or mixers (DE 2.0) available. diff --git a/Documentation/devicetree/bindings/dma/jz4780-dma.txt b/Documentation/devicetree/bindings/dma/jz4780-dma.txt index 03e9cf7b42e0..636fcb26b164 100644 --- a/Documentation/devicetree/bindings/dma/jz4780-dma.txt +++ b/Documentation/devicetree/bindings/dma/jz4780-dma.txt @@ -2,8 +2,13 @@ Required properties: -- compatible: Should be "ingenic,jz4780-dma" -- reg: Should contain the DMA controller registers location and length. +- compatible: Should be one of: + * ingenic,jz4740-dma + * ingenic,jz4725b-dma + * ingenic,jz4770-dma + * ingenic,jz4780-dma +- reg: Should contain the DMA channel registers location and length, followed + by the DMA controller registers location and length. - interrupts: Should contain the interrupt specifier of the DMA controller. - clocks: Should contain a clock specifier for the JZ4780 PDMA clock. - #dma-cells: Must be <2>. Number of integer cells in the dmas property of @@ -19,9 +24,10 @@ Optional properties: Example: -dma: dma@13420000 { +dma: dma-controller@13420000 { compatible = "ingenic,jz4780-dma"; - reg = <0x13420000 0x10000>; + reg = <0x13420000 0x400 + 0x13421000 0x40>; interrupt-parent = <&intc>; interrupts = <10>; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index 946229c48657..a5a7c3f5a1e3 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -17,6 +17,7 @@ Required Properties: - compatible: "renesas,dmac-<soctype>", "renesas,rcar-dmac" as fallback. Examples with soctypes are: - "renesas,dmac-r8a7743" (RZ/G1M) + - "renesas,dmac-r8a7744" (RZ/G1N) - "renesas,dmac-r8a7745" (RZ/G1E) - "renesas,dmac-r8a77470" (RZ/G1C) - "renesas,dmac-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index 482e54362d3e..1743017bd948 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -4,6 +4,7 @@ Required Properties: -compatible: "renesas,<soctype>-usb-dmac", "renesas,usb-dmac" as fallback. Examples with soctypes are: - "renesas,r8a7743-usb-dmac" (RZ/G1M) + - "renesas,r8a7744-usb-dmac" (RZ/G1N) - "renesas,r8a7745-usb-dmac" (RZ/G1E) - "renesas,r8a7790-usb-dmac" (R-Car H2) - "renesas,r8a7791-usb-dmac" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index fcf6979c0b6d..41f133a4e2fa 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -7,16 +7,23 @@ assorted actions. Required properties: - compatible: must contain one of the following: - * "qcom,scm-apq8064" for APQ8064 platforms - * "qcom,scm-msm8660" for MSM8660 platforms - * "qcom,scm-msm8690" for MSM8690 platforms - * "qcom,scm-msm8996" for MSM8996 platforms - * "qcom,scm-ipq4019" for IPQ4019 platforms - * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc) -- clocks: One to three clocks may be required based on compatible. - * No clock required for "qcom,scm-msm8996", "qcom,scm-ipq4019" - * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960" - * Core, iface, and bus clocks required for "qcom,scm" + * "qcom,scm-apq8064" + * "qcom,scm-apq8084" + * "qcom,scm-msm8660" + * "qcom,scm-msm8916" + * "qcom,scm-msm8960" + * "qcom,scm-msm8974" + * "qcom,scm-msm8996" + * "qcom,scm-msm8998" + * "qcom,scm-ipq4019" + * "qcom,scm-sdm845" + and: + * "qcom,scm" +- clocks: Specifies clocks needed by the SCM interface, if any: + * core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660" and + "qcom,scm-msm8960" + * core, iface and bus clocks required for "qcom,scm-apq8084", + "qcom,scm-msm8916" and "qcom,scm-msm8974" - clock-names: Must contain "core" for the core clock, "iface" for the interface clock and "bus" for the bus clock per the requirements of the compatible. - qcom,dload-mode: phandle to the TCSR hardware block and offset of the @@ -26,8 +33,10 @@ Example for MSM8916: firmware { scm { - compatible = "qcom,scm"; - clocks = <&gcc GCC_CRYPTO_CLK> , <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>; + compatible = "qcom,msm8916", "qcom,scm"; + clocks = <&gcc GCC_CRYPTO_CLK> , + <&gcc GCC_CRYPTO_AXI_CLK>, + <&gcc GCC_CRYPTO_AHB_CLK>; clock-names = "core", "bus", "iface"; }; }; diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt new file mode 100644 index 000000000000..614bac55df86 --- /dev/null +++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt @@ -0,0 +1,82 @@ +----------------------------------------------------------------- +Device Tree Bindings for the Xilinx Zynq MPSoC Firmware Interface +----------------------------------------------------------------- + +The zynqmp-firmware node describes the interface to platform firmware. +ZynqMP has an interface to communicate with secure firmware. Firmware +driver provides an interface to firmware APIs. Interface APIs can be +used by any driver to communicate to PMUFW(Platform Management Unit). +These requests include clock management, pin control, device control, +power management service, FPGA service and other platform management +services. + +Required properties: + - compatible: Must contain: "xlnx,zynqmp-firmware" + - method: The method of calling the PM-API firmware layer. + Permitted values are: + - "smc" : SMC #0, following the SMCCC + - "hvc" : HVC #0, following the SMCCC + +-------------------------------------------------------------------------- +Device Tree Clock bindings for the Zynq Ultrascale+ MPSoC controlled using +Zynq MPSoC firmware interface +-------------------------------------------------------------------------- +The clock controller is a h/w block of Zynq Ultrascale+ MPSoC clock +tree. It reads required input clock frequencies from the devicetree and acts +as clock provider for all clock consumers of PS clocks. + +See clock_bindings.txt for more information on the generic clock bindings. + +Required properties: + - #clock-cells: Must be 1 + - compatible: Must contain: "xlnx,zynqmp-clk" + - clocks: List of clock specifiers which are external input + clocks to the given clock controller. Please refer + the next section to find the input clocks for a + given controller. + - clock-names: List of clock names which are exteral input clocks + to the given clock controller. Please refer to the + clock bindings for more details. + +Input clocks for zynqmp Ultrascale+ clock controller: + +The Zynq UltraScale+ MPSoC has one primary and four alternative reference clock +inputs. These required clock inputs are: + - pss_ref_clk (PS reference clock) + - video_clk (reference clock for video system ) + - pss_alt_ref_clk (alternative PS reference clock) + - aux_ref_clk + - gt_crx_ref_clk (transceiver reference clock) + +The following strings are optional parameters to the 'clock-names' property in +order to provide an optional (E)MIO clock source: + - swdt0_ext_clk + - swdt1_ext_clk + - gem0_emio_clk + - gem1_emio_clk + - gem2_emio_clk + - gem3_emio_clk + - mio_clk_XX # with XX = 00..77 + - mio_clk_50_or_51 #for the mux clock to gem tsu from 50 or 51 + + +Output clocks are registered based on clock information received +from firmware. Output clocks indexes are mentioned in +include/dt-bindings/clock/xlnx,zynqmp-clk.h. + +------- +Example +------- + +firmware { + zynqmp_firmware: zynqmp-firmware { + compatible = "xlnx,zynqmp-firmware"; + method = "smc"; + zynqmp_clk: clock-controller { + #clock-cells = <1>; + compatible = "xlnx,zynqmp-clk"; + clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>, <&aux_ref_clk>, <>_crx_ref_clk>; + clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/fpga/fpga-region.txt b/Documentation/devicetree/bindings/fpga/fpga-region.txt index 6db8aeda461a..90c44694a30b 100644 --- a/Documentation/devicetree/bindings/fpga/fpga-region.txt +++ b/Documentation/devicetree/bindings/fpga/fpga-region.txt @@ -415,7 +415,7 @@ DT Overlay contains: firmware-name = "base.rbf"; fpga-bridge@4400 { - compatible = "altr,freeze-bridge"; + compatible = "altr,freeze-bridge-controller"; reg = <0x4400 0x10>; fpga_region1: fpga-region1 { @@ -427,7 +427,7 @@ DT Overlay contains: }; fpga-bridge@4420 { - compatible = "altr,freeze-bridge"; + compatible = "altr,freeze-bridge-controller"; reg = <0x4420 0x10>; fpga_region2: fpga-region2 { diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index a7c31de29362..f0ba154b5723 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -1,18 +1,9 @@ Specifying GPIO information for devices -============================================ +======================================= 1) gpios property ----------------- -Nodes that makes use of GPIOs should specify them using one or more -properties, each containing a 'gpio-list': - - gpio-list ::= <single-gpio> [gpio-list] - single-gpio ::= <gpio-phandle> <gpio-specifier> - gpio-phandle : phandle to gpio controller node - gpio-specifier : Array of #gpio-cells specifying specific gpio - (controller specific) - GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed @@ -33,33 +24,27 @@ The following example could be used to describe GPIO pins used as device enable and bit-banged data signals: gpio1: gpio1 { - gpio-controller - #gpio-cells = <2>; - }; - gpio2: gpio2 { - gpio-controller - #gpio-cells = <1>; + gpio-controller; + #gpio-cells = <2>; }; [...] - enable-gpios = <&gpio2 2>; data-gpios = <&gpio1 12 0>, <&gpio1 13 0>, <&gpio1 14 0>, <&gpio1 15 0>; -Note that gpio-specifier length is controller dependent. In the -above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 -only uses one. +In the above example, &gpio1 uses 2 cells to specify a gpio. The first cell is +a local offset to the GPIO line and the second cell represent consumer flags, +such as if the consumer desire the line to be active low (inverted) or open +drain. This is the recommended practice. -gpio-specifier may encode: bank, pin position inside the bank, -whether pin is open-drain and whether pin is logically inverted. +The exact meaning of each specifier cell is controller specific, and must be +documented in the device tree binding for the device, but it is strongly +recommended to use the two-cell approach. -Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. - -Most controllers are however specifying a generic flag bitfield -in the last cell, so for these, use the macros defined in +Most controllers are specifying a generic flag bitfield in the last cell, so +for these, use the macros defined in include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -236,46 +221,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: Some or all of the GPIOs provided by a GPIO controller may be routed to pins on the package via a pin controller. This allows muxing those pins between -GPIO and other functions. +GPIO and other functions. It is a fairly common practice among silicon +engineers. + +2.2) Ordinary (numerical) GPIO ranges +------------------------------------- It is useful to represent which GPIOs correspond to which pins on which pin -controllers. The gpio-ranges property described below represents this, and -contains information structures as follows: - - gpio-range-list ::= <single-gpio-range> [gpio-range-list] - single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range> - numeric-gpio-range ::= - <pinctrl-phandle> <gpio-base> <pinctrl-base> <count> - named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>' - pinctrl-phandle : phandle to pin controller node - gpio-base : Base GPIO ID in the GPIO controller - pinctrl-base : Base pinctrl pin ID in the pin controller - count : The number of GPIOs/pins in this range - -The "pin controller node" mentioned above must conform to the bindings -described in ../pinctrl/pinctrl-bindings.txt. - -In case named gpio ranges are used (ranges with both <pinctrl-base> and -<count> set to 0), the property gpio-ranges-group-names contains one string -for every single-gpio-range in gpio-ranges: - gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list] - gpiorange-name : Name of the pingroup associated to the GPIO range in - the respective pin controller. - -Elements of gpiorange-names-list corresponding to numeric ranges contain -the empty string. Elements of gpiorange-names-list corresponding to named -ranges contain the name of a pin group defined in the respective pin -controller. The number of pins/GPIOs in the range is the number of pins in -that pin group. +controllers. The gpio-ranges property described below represents this with +a discrete set of ranges mapping pins from the pin controller local number space +to pins in the GPIO controller local number space. -Previous versions of this binding required all pin controller nodes that -were referenced by any gpio-ranges property to contain a property named -#gpio-range-cells with value <3>. This requirement is now deprecated. -However, that property may still exist in older device trees for -compatibility reasons, and would still be required even in new device -trees that need to be compatible with older software. +The format is: <[pin controller phandle], [GPIO controller offset], + [pin controller offset], [number of pins]>; + +The GPIO controller offset pertains to the GPIO controller node containing the +range definition. + +The pin controller node referenced by the phandle must conform to the bindings +described in pinctrl/pinctrl-bindings.txt. + +Each offset runs from 0 to N. It is perfectly fine to pile any number of +ranges with just one pin-to-GPIO line mapping if the ranges are concocted, but +in practice these ranges are often lumped in discrete sets. + +Example: + + gpio-ranges = <&foo 0 20 10>, <&bar 10 50 20>; -Example 1: +This means: +- pins 20..29 on pin controller "foo" is mapped to GPIO line 0..9 and +- pins 50..69 on pin controller "bar" is mapped to GPIO line 10..29 + + +Verbose example: qe_pio_e: gpio-controller@1460 { #gpio-cells = <2>; @@ -289,7 +268,28 @@ Here, a single GPIO controller has GPIOs 0..9 routed to pin controller pinctrl1's pins 20..29, and GPIOs 10..29 routed to pin controller pinctrl2's pins 50..69. -Example 2: + +2.3) GPIO ranges from named pin groups +-------------------------------------- + +It is also possible to use pin groups for gpio ranges when pin groups are the +easiest and most convenient mapping. + +Both both <pinctrl-base> and <count> must set to 0 when using named pin groups +names. + +The property gpio-ranges-group-names must contain exactly one string for each +range. + +Elements of gpio-ranges-group-names must contain the name of a pin group +defined in the respective pin controller. The number of pins/GPIO lines in the +range is the number of pins in that pin group. The number of pins of that +group is defined int the implementation and not in the device tree. + +If numerical and named pin groups are mixed, the string corresponding to a +numerical pin range in gpio-ranges-group-names must be empty. + +Example: gpio_pio_i: gpio-controller@14b0 { #gpio-cells = <2>; @@ -306,6 +306,14 @@ Example 2: "bar"; }; -Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO -ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 -are named "foo" and "bar". +Here, three GPIO ranges are defined referring to two pin controllers. + +pinctrl1 GPIO ranges are defined using pin numbers whereas the GPIO ranges +in pinctrl2 are defined using the pin groups named "foo" and "bar". + +Previous versions of this binding required all pin controller nodes that +were referenced by any gpio-ranges property to contain a property named +#gpio-range-cells with value <3>. This requirement is now deprecated. +However, that property may still exist in older device trees for +compatibility reasons, and would still be required even in new device +trees that need to be compatible with older software. diff --git a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt deleted file mode 100644 index 7988aeb725f4..000000000000 --- a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt +++ /dev/null @@ -1,46 +0,0 @@ -Ingenic jz47xx GPIO controller - -That the Ingenic GPIO driver node must be a sub-node of the Ingenic pinctrl -driver node. - -Required properties: --------------------- - - - compatible: Must contain one of: - - "ingenic,jz4740-gpio" - - "ingenic,jz4770-gpio" - - "ingenic,jz4780-gpio" - - reg: The GPIO bank number. - - interrupt-controller: Marks the device node as an interrupt controller. - - interrupts: Interrupt specifier for the controllers interrupt. - - #interrupt-cells: Should be 2. Refer to - ../interrupt-controller/interrupts.txt for more details. - - gpio-controller: Marks the device node as a GPIO controller. - - #gpio-cells: Should be 2. The first cell is the GPIO number and the second - cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the - GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. Refer to - 'gpio.txt' in this directory for more details. - -Example: --------- - -&pinctrl { - #address-cells = <1>; - #size-cells = <0>; - - gpa: gpio@0 { - compatible = "ingenic,jz4740-gpio"; - reg = <0>; - - gpio-controller; - gpio-ranges = <&pinctrl 0 0 32>; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - - interrupt-parent = <&intc>; - interrupts = <28>; - }; -}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 4018ee57a6af..2889bbcd7416 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -4,8 +4,10 @@ Required Properties: - compatible: should contain one or more of the following: - "renesas,gpio-r8a7743": for R8A7743 (RZ/G1M) compatible GPIO controller. + - "renesas,gpio-r8a7744": for R8A7744 (RZ/G1N) compatible GPIO controller. - "renesas,gpio-r8a7745": for R8A7745 (RZ/G1E) compatible GPIO controller. - "renesas,gpio-r8a77470": for R8A77470 (RZ/G1C) compatible GPIO controller. + - "renesas,gpio-r8a774a1": for R8A774A1 (RZ/G2M) compatible GPIO controller. - "renesas,gpio-r8a7778": for R8A7778 (R-Car M1) compatible GPIO controller. - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. @@ -22,7 +24,7 @@ Required Properties: - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. - "renesas,rcar-gen2-gpio": for a generic R-Car Gen2 or RZ/G1 GPIO controller. - - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 GPIO controller. + - "renesas,rcar-gen3-gpio": for a generic R-Car Gen3 or RZ/G2 GPIO controller. - "renesas,gpio-rcar": deprecated. When compatible with the generic version nodes must list the @@ -38,7 +40,7 @@ Required Properties: - #gpio-cells: Should be 2. The first cell is the GPIO number and the second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. - - gpio-ranges: Range of pins managed by the GPIO controller. + - gpio-ranges: See gpio.txt. Optional properties: @@ -46,35 +48,44 @@ Optional properties: mandatory if the hardware implements a controllable functional clock for the GPIO instance. -Please refer to gpio.txt in this directory for details of gpio-ranges property -and the common GPIO bindings used by client devices. + - gpio-reserved-ranges: See gpio.txt. + +Please refer to gpio.txt in this directory for the common GPIO bindings used by +client devices. The GPIO controller also acts as an interrupt controller. It uses the default two cells specifier as described in Documentation/devicetree/bindings/ interrupt-controller/interrupts.txt. -Example: R8A7779 (R-Car H1) GPIO controller nodes +Example: R8A77470 (RZ/G1C) GPIO controller nodes - gpio0: gpio@ffc40000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc40000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 141 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 0 32>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio0: gpio@e6050000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6050000 0 0x50>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 23>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 912>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 912>; + }; ... - gpio6: gpio@ffc46000 { - compatible = "renesas,gpio-r8a7779", "renesas,rcar-gen1-gpio"; - reg = <0xffc46000 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 147 0x4>; - #gpio-cells = <2>; - gpio-controller; - gpio-ranges = <&pfc 0 192 9>; - interrupt-controller; - #interrupt-cells = <2>; - }; + gpio3: gpio@e6053000 { + compatible = "renesas,gpio-r8a77470", + "renesas,rcar-gen2-gpio"; + reg = <0 0xe6053000 0 0x50>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 30>; + gpio-reserved-ranges = <17 10>; + #interrupt-cells = <2>; + interrupt-controller; + clocks = <&cpg CPG_MOD 909>; + power-domains = <&sysc R8A77470_PD_ALWAYS_ON>; + resets = <&cpg 909>; + }; diff --git a/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt new file mode 100644 index 000000000000..1b30812b015b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/snps,creg-gpio.txt @@ -0,0 +1,21 @@ +Synopsys GPIO via CREG (Control REGisters) driver + +Required properties: +- compatible : "snps,creg-gpio-hsdk" or "snps,creg-gpio-axs10x". +- reg : Exactly one register range with length 0x4. +- #gpio-cells : Since the generic GPIO binding is used, the + amount of cells must be specified as 2. The first cell is the + pin number, the second cell is used to specify optional parameters: + See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- gpio-controller : Marks the device node as a GPIO controller. +- ngpios: Number of GPIO pins. + +Example: + +gpio: gpio@f00014b0 { + compatible = "snps,creg-gpio-hsdk"; + reg = <0xf00014b0 0x4>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <2>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ina3221.txt b/Documentation/devicetree/bindings/hwmon/ina3221.txt new file mode 100644 index 000000000000..a7b25caa2b8e --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ina3221.txt @@ -0,0 +1,44 @@ +Texas Instruments INA3221 Device Tree Bindings + +1) ina3221 node + Required properties: + - compatible: Must be "ti,ina3221" + - reg: I2C address + + Optional properties: + = The node contains optional child nodes for three channels = + = Each child node describes the information of input source = + + - #address-cells: Required only if a child node is present. Must be 1. + - #size-cells: Required only if a child node is present. Must be 0. + +2) child nodes + Required properties: + - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221 + + Optional properties: + - label: Name of the input source + - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm + +Example: + +ina3221@40 { + compatible = "ti,ina3221"; + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + + input@0 { + reg = <0x0>; + status = "disabled"; + }; + input@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <5000>; + }; + input@2 { + reg = <0x2>; + label = "VDD_5V"; + shunt-resistor-micro-ohms = <5000>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt index bf2a47bbdc58..b428a70a7cc0 100644 --- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -15,6 +15,7 @@ Required properties: * "lltc,ltm2987" * "lltc,ltm4675" * "lltc,ltm4676" + * "lltc,ltm4686" - reg: I2C slave address Optional properties: @@ -30,6 +31,7 @@ Valid names of regulators depend on number of supplies supported per device: * ltc3880, ltc3882, ltc3886 : vout0 - vout1 * ltc3883 : vout0 * ltm4676 : vout0 - vout1 + * ltm4686 : vout0 - vout1 Example: ltc2978@5e { diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index fbb0a6d8b964..3e4bcc2fb6f7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -3,6 +3,7 @@ Required properties : - compatible : should be "snps,designware-i2c" + or "mscc,ocelot-i2c" with "snps,designware-i2c" for fallback - reg : Offset and length of the register set for the device - interrupts : <IRQ> where IRQ is the interrupt number. @@ -11,8 +12,12 @@ Recommended properties : - clock-frequency : desired I2C bus clock frequency in Hz. Optional properties : + - reg : for "mscc,ocelot-i2c", a second register set to configure the SDA hold + time, named ICPU_CFG:TWI_DELAY in the datasheet. + - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. - This option is only supported in hardware blocks version 1.11a or newer. + This option is only supported in hardware blocks version 1.11a or newer and + on Microsemi SoCs ("mscc,ocelot-i2c" compatible). - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds. This value which is by default 300ns is used to compute the tLOW period. diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt index 00e4365d7206..091c8dfd3229 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -3,7 +3,6 @@ Required properties: - compatible : - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc - - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc - reg : address and length of the lpi2c master registers - interrupts : lpi2c interrupt - clocks : lpi2c clock specifier @@ -11,7 +10,7 @@ Required properties: Examples: lpi2c7: lpi2c7@40a50000 { - compatible = "fsl,imx8dv-lpi2c"; + compatible = "fsl,imx7ulp-lpi2c"; reg = <0x40A50000 0x10000>; interrupt-parent = <&intc>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 39cd21d95810..30c0485b167b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -3,7 +3,9 @@ I2C for R-Car platforms Required properties: - compatible: "renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC. + "renesas,i2c-r8a7744" if the device is a part of a R8A7744 SoC. "renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC. + "renesas,i2c-r8a77470" if the device is a part of a R8A77470 SoC. "renesas,i2c-r8a774a1" if the device is a part of a R8A774A1 SoC. "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 872673adff5a..d81b62643655 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) - "renesas,iic-r8a7743" (RZ/G1M) + - "renesas,iic-r8a7744" (RZ/G1N) - "renesas,iic-r8a7745" (RZ/G1E) - "renesas,iic-r8a774a1" (RZ/G2M) - "renesas,iic-r8a7790" (R-Car H2) diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index 11263982470e..44efafdfd7f5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -84,7 +84,7 @@ Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first interrupt if not using interrupt names) as primary interrupt for the slave. -Alternatively, devices supporting SMbus Host Notify, and connected to +Alternatively, devices supporting SMBus Host Notify, and connected to adapters that support this feature, may use "host-notify" property. I2C core will create a virtual interrupt for Host Notify and assign it as primary interrupt for the slave. diff --git a/Documentation/devicetree/bindings/iio/accel/adxl372.txt b/Documentation/devicetree/bindings/iio/accel/adxl372.txt new file mode 100644 index 000000000000..a289964756a7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adxl372.txt @@ -0,0 +1,33 @@ +Analog Devices ADXL372 3-Axis, +/-(200g) Digital Accelerometer + +http://www.analog.com/media/en/technical-documentation/data-sheets/adxl372.pdf + +Required properties: + - compatible : should be "adi,adxl372" + - reg: the I2C address or SPI chip select number for the device + +Required properties for SPI bus usage: + - spi-max-frequency: Max SPI frequency to use + +Optional properties: + - interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example for a I2C device node: + + accelerometer@53 { + compatible = "adi,adxl372"; + reg = <0x53>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; + +Example for a SPI device node: + + accelerometer@0 { + compatible = "adi,adxl372"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3911.txt b/Documentation/devicetree/bindings/iio/adc/mcp3911.txt new file mode 100644 index 000000000000..3071f48fb30b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mcp3911.txt @@ -0,0 +1,30 @@ +* Microchip MCP3911 Dual channel analog front end (ADC) + +Required properties: + - compatible: Should be "microchip,mcp3911" + - reg: SPI chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt. + Max frequency for this chip is 20MHz. + +Optional properties: + - clocks: Phandle and clock identifier for sampling clock + - interrupt-parent: Phandle to the parent interrupt controller + - interrupts: IRQ line for the ADC + - microchip,device-addr: Device address when multiple MCP3911 chips are present on the + same SPI bus. Valid values are 0-3. Defaults to 0. + - vref-supply: Phandle to the external reference voltage supply. + +Example: +adc@0 { + compatible = "microchip,mcp3911"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <20000000>; + microchip,device-addr = <0>; + vref-supply = <&vref_reg>; + clocks = <&xtal>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt index 0fb46137f936..b3c86f4ac7cd 100644 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt @@ -1,7 +1,9 @@ -Qualcomm's SPMI PMIC voltage ADC +Qualcomm's SPMI PMIC ADC -SPMI PMIC voltage ADC (VADC) provides interface to clients to read -voltage. The VADC is a 15-bit sigma-delta ADC. +- SPMI PMIC voltage ADC (VADC) provides interface to clients to read + voltage. The VADC is a 15-bit sigma-delta ADC. +- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read + voltage. The VADC is a 16-bit sigma-delta ADC. VADC node: @@ -9,11 +11,13 @@ VADC node: Usage: required Value type: <string> Definition: Should contain "qcom,spmi-vadc". + Should contain "qcom,spmi-adc5" for PMIC5 ADC driver. + Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver. - reg: Usage: required Value type: <prop-encoded-array> - Definition: VADC base address and length in the SPMI PMIC register map. + Definition: VADC base address in the SPMI PMIC register map. - #address-cells: Usage: required @@ -45,13 +49,26 @@ Channel node properties: Definition: ADC channel number. See include/dt-bindings/iio/qcom,spmi-vadc.h +- label: + Usage: required for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2" + Value type: <empty> + Definition: ADC input of the platform as seen in the schematics. + For thermistor inputs connected to generic AMUX or GPIO inputs + these can vary across platform for the same pins. Hence select + the platform schematics name for this channel. + - qcom,decimation: Usage: optional Value type: <u32> Definition: This parameter is used to decrease ADC sampling rate. Quicker measurements can be made by reducing decimation ratio. - Valid values are 512, 1024, 2048, 4096. - If property is not found, default value of 512 will be used. + - For compatible property "qcom,spmi-vadc", valid values are + 512, 1024, 2048, 4096. If property is not found, default value + of 512 will be used. + - For compatible property "qcom,spmi-adc5", valid values are 250, 420 + and 840. If property is not found, default value of 840 is used. + - For compatible property "qcom,spmi-adc-rev2", valid values are 256, + 512 and 1024. If property is not present, default value is 1024. - qcom,pre-scaling: Usage: optional @@ -66,21 +83,38 @@ Channel node properties: - qcom,ratiometric: Usage: optional Value type: <empty> - Definition: Channel calibration type. If this property is specified - VADC will use the VDD reference (1.8V) and GND for channel - calibration. If property is not found, channel will be - calibrated with 0.625V and 1.25V reference channels, also - known as absolute calibration. + Definition: Channel calibration type. + - For compatible property "qcom,spmi-vadc", if this property is + specified VADC will use the VDD reference (1.8V) and GND for + channel calibration. If property is not found, channel will be + calibrated with 0.625V and 1.25V reference channels, also + known as absolute calibration. + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2", + if this property is specified VADC will use the VDD reference + (1.875V) and GND for channel calibration. If property is not found, + channel will be calibrated with 0V and 1.25V reference channels, + also known as absolute calibration. - qcom,hw-settle-time: Usage: optional Value type: <u32> Definition: Time between AMUX getting configured and the ADC starting - conversion. Delay = 100us * (value) for value < 11, and - 2ms * (value - 10) otherwise. - Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800, - 900 us and 1, 2, 4, 6, 8, 10 ms - If property is not found, channel will use 0us. + conversion. The 'hw_settle_time' is an index used from valid values + and programmed in hardware to achieve the hardware settling delay. + - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2", + Delay = 100us * (hw_settle_time) for hw_settle_time < 11, + and 2ms * (hw_settle_time - 10) otherwise. + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800, + 900 us and 1, 2, 4, 6, 8, 10 ms. + If property is not found, channel will use 0us. + - For compatible property "qcom,spmi-adc5", delay = 15us for + value 0, 100us * (value) for values < 11, + and 2ms * (value - 10) otherwise. + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800, + 900 us and 1, 2, 4, 6, 8, 10 ms + Certain controller digital versions have valid values of + 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms + If property is not found, channel will use 15us. - qcom,avg-samples: Usage: optional @@ -89,13 +123,18 @@ Channel node properties: Averaging provides the option to obtain a single measurement from the ADC that is an average of multiple samples. The value selected is 2^(value). - Valid values are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512 - If property is not found, 1 sample will be used. + - For compatible property "qcom,spmi-vadc", valid values + are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512 + If property is not found, 1 sample will be used. + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2", + valid values are: 1, 2, 4, 8, 16 + If property is not found, 1 sample will be used. NOTE: -Following channels, also known as reference point channels, are used for -result calibration and their channel configuration nodes should be defined: +For compatible property "qcom,spmi-vadc" following channels, also known as +reference point channels, are used for result calibration and their channel +configuration nodes should be defined: VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV, VADC_GND_REF and VADC_VDD_VADC. @@ -104,7 +143,7 @@ Example: /* VADC node */ pmic_vadc: vadc@3100 { compatible = "qcom,spmi-vadc"; - reg = <0x3100 0x100>; + reg = <0x3100>; interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt index 8aad960de50b..b4daa15dcf15 100644 --- a/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt @@ -12,6 +12,8 @@ Required properties: - interrupts: The interrupt number for the ADC device. - #io-channel-cells: Number of cells in an IIO specifier. - hwlocks: Reference to a phandle of a hwlock provider node. +- nvmem-cells: A phandle to the calibration cells provided by eFuse device. +- nvmem-cell-names: Should be "big_scale_calib", "small_scale_calib". Example: @@ -32,5 +34,7 @@ Example: interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; #io-channel-cells = <1>; hwlocks = <&hwlock 4>; + nvmem-cells = <&adc_big_scale>, <&adc_small_scale>; + nvmem-cell-names = "big_scale_calib", "small_scale_calib"; }; }; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5758.txt b/Documentation/devicetree/bindings/iio/dac/ad5758.txt index bba01a5cab1b..2f607f41f9d3 100644 --- a/Documentation/devicetree/bindings/iio/dac/ad5758.txt +++ b/Documentation/devicetree/bindings/iio/dac/ad5758.txt @@ -50,6 +50,9 @@ Required properties: Optional properties: + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be + asserted during driver probe. + - adi,dc-dc-ilim-microamp: The dc-to-dc converter current limit The following values are currently supported [uA]: * 150000 @@ -71,6 +74,8 @@ AD5758 Example: spi-max-frequency = <1000000>; spi-cpha; + reset-gpios = <&gpio 22 0>; + adi,dc-dc-mode = <2>; adi,range-microvolt = <0 10000000>; adi,dc-dc-ilim-microamp = <200000>; diff --git a/Documentation/devicetree/bindings/iio/dac/ltc1660.txt b/Documentation/devicetree/bindings/iio/dac/ltc1660.txt new file mode 100644 index 000000000000..c5b5f22d6c64 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ltc1660.txt @@ -0,0 +1,21 @@ +* Linear Technology Micropower octal 8-Bit and 10-Bit DACs + +Required properties: + - compatible: Must be one of the following: + "lltc,ltc1660" + "lltc,ltc1665" + - reg: SPI chip select number for the device + - vref-supply: Phandle to the voltage reference supply + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt. + Max frequency for this chip is 5 MHz. + +Example: +dac@0 { + compatible = "lltc,ltc1660"; + reg = <0>; + spi-max-frequency = <5000000>; + vref-supply = <&vref_reg>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index b2f27da847b8..6ab9a9d196b0 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -20,6 +20,7 @@ Required properties: bindings. Optional properties: + - vddio-supply: regulator phandle for VDDIO supply - mount-matrix: an optional 3x3 mounting rotation matrix - i2c-gate node. These devices also support an auxiliary i2c bus. This is simple enough to be described using the i2c-gate binding. See diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index ea2d6e0ae4c5..879322ad50fd 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -7,6 +7,7 @@ Required properties: "st,lsm6dsl" "st,lsm6dsm" "st,ism330dlc" + "st,lsm6dso" - reg: i2c address of the sensor / spi cs line Optional properties: diff --git a/Documentation/devicetree/bindings/iio/light/bh1750.txt b/Documentation/devicetree/bindings/iio/light/bh1750.txt new file mode 100644 index 000000000000..1e7685797d7a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/bh1750.txt @@ -0,0 +1,18 @@ +ROHM BH1750 - ALS, Ambient light sensor + +Required properties: + +- compatible: Must be one of: + "rohm,bh1710" + "rohm,bh1715" + "rohm,bh1721" + "rohm,bh1750" + "rohm,bh1751" +- reg: the I2C address of the sensor + +Example: + +light-sensor@23 { + compatible = "rohm,bh1750"; + reg = <0x23>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2772.txt b/Documentation/devicetree/bindings/iio/light/tsl2772.txt new file mode 100644 index 000000000000..1c5e6f17a1df --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2772.txt @@ -0,0 +1,42 @@ +* AMS/TAOS ALS and proximity sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2571" + "amstaos,tsl2671" + "amstaos,tmd2671" + "amstaos,tsl2771" + "amstaos,tmd2771" + "amstaos,tsl2572" + "amstaos,tsl2672" + "amstaos,tmd2672" + "amstaos,tsl2772" + "amstaos,tmd2772" + "avago,apds9930" + - reg: the I2C address of the device + +Optional properties: + + - amstaos,proximity-diodes - proximity diodes to enable. <0>, <1>, or <0 1> + are the only valid values. + - led-max-microamp - current for the proximity LED. Must be 100000, 50000, + 25000, or 13000. + - vdd-supply: phandle to the regulator that provides power to the sensor. + - vddio-supply: phandle to the regulator that provides power to the bus. + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +tsl2772@39 { + compatible = "amstaos,tsl2772"; + reg = <0x39>; + interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pm8941_l17>; + vddio-supply = <&pm8941_lvs1>; + amstaos,proximity-diodes = <0>; + led-max-microamp = <100000>; +}; diff --git a/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt b/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt new file mode 100644 index 000000000000..aac5f621f8dc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt @@ -0,0 +1,12 @@ +ST VL53L0X ToF ranging sensor + +Required properties: + - compatible: must be "st,vl53l0x" + - reg: i2c address where to find the device + +Example: + +vl53l0x@29 { + compatible = "st,vl53l0x"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 996ce84352cb..7cccc49b6bea 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -1,4 +1,4 @@ -Device-Tree bindings for input/gpio_keys.c keyboard driver +Device-Tree bindings for input/keyboard/gpio_keys.c keyboard driver Required properties: - compatible = "gpio-keys"; diff --git a/Documentation/devicetree/bindings/input/pwm-vibrator.txt b/Documentation/devicetree/bindings/input/pwm-vibrator.txt index 09145d18491d..88c775a3fe21 100644 --- a/Documentation/devicetree/bindings/input/pwm-vibrator.txt +++ b/Documentation/devicetree/bindings/input/pwm-vibrator.txt @@ -58,8 +58,8 @@ Example from Motorola Droid 4: vibrator { compatible = "pwm-vibrator"; - pwms = <&pwm8 0 1000000000 0>, - <&pwm9 0 1000000000 0>; + pwms = <&pwm9 0 1000000000 0>, + <&pwm8 0 1000000000 0>; pwm-names = "enable", "direction"; direction-duty-cycle-ns = <1000000000>; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt index d092d5d033a0..8641a2d70851 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -1,10 +1,12 @@ General Touchscreen Properties: Optional properties for Touchscreens: + - touchscreen-min-x : minimum x coordinate reported (0 if not set) + - touchscreen-min-y : minimum y coordinate reported (0 if not set) - touchscreen-size-x : horizontal resolution of touchscreen - (in pixels) + (maximum x coordinate reported + 1) - touchscreen-size-y : vertical resolution of touchscreen - (in pixels) + (maximum y coordinate reported + 1) - touchscreen-max-pressure : maximum reported pressure (arbitrary range dependent on the controller) - touchscreen-min-pressure : minimum pressure on the touchscreen to be diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt new file mode 100644 index 000000000000..44286dcbac62 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt @@ -0,0 +1,62 @@ +============================== +C-SKY APB Interrupt Controller +============================== + +C-SKY APB Interrupt Controller is a simple soc interrupt controller +on the apb bus and we only use it as root irq controller. + + - csky,apb-intc is used in a lot of csky fpgas and socs, it support 64 irq nums. + - csky,dual-apb-intc consists of 2 apb-intc and 128 irq nums supported. + - csky,gx6605s-intc is gx6605s soc internal irq interrupt controller, 64 irq nums. + +============================= +intc node bindings definition +============================= + + Description: Describes APB interrupt controller + + PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: must be "csky,apb-intc" + "csky,dual-apb-intc" + "csky,gx6605s-intc" + - #interrupt-cells + Usage: required + Value type: <u32> + Definition: must be <1> + - reg + Usage: required + Value type: <u32 u32> + Definition: <phyaddr size> in soc from cpu view + - interrupt-controller: + Usage: required + - csky,support-pulse-signal: + Usage: select + Description: to support pulse signal flag + +Examples: +--------- + + intc: interrupt-controller@500000 { + compatible = "csky,apb-intc"; + #interrupt-cells = <1>; + reg = <0x00500000 0x400>; + interrupt-controller; + }; + + intc: interrupt-controller@500000 { + compatible = "csky,dual-apb-intc"; + #interrupt-cells = <1>; + reg = <0x00500000 0x400>; + interrupt-controller; + }; + + intc: interrupt-controller@500000 { + compatible = "csky,gx6605s-intc"; + #interrupt-cells = <1>; + reg = <0x00500000 0x400>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt new file mode 100644 index 000000000000..ab921f1698fb --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt @@ -0,0 +1,40 @@ +=========================================== +C-SKY Multi-processors Interrupt Controller +=========================================== + +C-SKY Multi-processors Interrupt Controller is designed for ck807/ck810/ck860 +SMP soc, and it also could be used in non-SMP system. + +Interrupt number definition: + + 0-15 : software irq, and we use 15 as our IPI_IRQ. + 16-31 : private irq, and we use 16 as the co-processor timer. + 31-1024: common irq for soc ip. + +============================= +intc node bindings definition +============================= + + Description: Describes SMP interrupt controller + + PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: must be "csky,mpintc" + - #interrupt-cells + Usage: required + Value type: <u32> + Definition: must be <1> + - interrupt-controller: + Usage: required + +Examples: +--------- + + intc: interrupt-controller { + compatible = "csky,mpintc"; + #interrupt-cells = <1>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt index aa8bf2ec8905..1c94a57a661e 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt @@ -5,6 +5,8 @@ The Marvell ICU (Interrupt Consolidation Unit) controller is responsible for collecting all wired-interrupt sources in the CP and communicating them to the GIC in the AP, the unit translates interrupt requests on input wires to MSG memory mapped transactions to the GIC. +These messages will access a different GIC memory area depending on +their type (NSR, SR, SEI, REI, etc). Required properties: @@ -12,20 +14,23 @@ Required properties: - reg: Should contain ICU registers location and length. -- #interrupt-cells: Specifies the number of cells needed to encode an - interrupt source. The value shall be 3. +Subnodes: Each group of interrupt is declared as a subnode of the ICU, +with their own compatible. + +Required properties for the icu_nsr/icu_sei subnodes: - The 1st cell is the group type of the ICU interrupt. Possible group - types are: +- compatible: Should be one of: + * "marvell,cp110-icu-nsr" + * "marvell,cp110-icu-sr" + * "marvell,cp110-icu-sei" + * "marvell,cp110-icu-rei" - ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure - ICU_GRP_SR (0x1) : Shared peripheral interrupt, secure - ICU_GRP_SEI (0x4) : System error interrupt - ICU_GRP_REI (0x5) : RAM error interrupt +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. - The 2nd cell is the index of the interrupt in the ICU unit. + The 1st cell is the index of the interrupt in the ICU unit. - The 3rd cell is the type of the interrupt. See arm,gic.txt for + The 2nd cell is the type of the interrupt. See arm,gic.txt for details. - interrupt-controller: Identifies the node as an interrupt @@ -35,17 +40,73 @@ Required properties: that allows to trigger interrupts using MSG memory mapped transactions. +Note: each 'interrupts' property referring to any 'icu_xxx' node shall + have a different number within [0:206]. + Example: icu: interrupt-controller@1e0000 { compatible = "marvell,cp110-icu"; - reg = <0x1e0000 0x10>; + reg = <0x1e0000 0x440>; + + CP110_LABEL(icu_nsr): interrupt-controller@10 { + compatible = "marvell,cp110-icu-nsr"; + reg = <0x10 0x20>; + #interrupt-cells = <2>; + interrupt-controller; + msi-parent = <&gicp>; + }; + + CP110_LABEL(icu_sei): interrupt-controller@50 { + compatible = "marvell,cp110-icu-sei"; + reg = <0x50 0x10>; + #interrupt-cells = <2>; + interrupt-controller; + msi-parent = <&sei>; + }; +}; + +node1 { + interrupt-parent = <&icu_nsr>; + interrupts = <106 IRQ_TYPE_LEVEL_HIGH>; +}; + +node2 { + interrupt-parent = <&icu_sei>; + interrupts = <107 IRQ_TYPE_LEVEL_HIGH>; +}; + +/* Would not work with the above nodes */ +node3 { + interrupt-parent = <&icu_nsr>; + interrupts = <107 IRQ_TYPE_LEVEL_HIGH>; +}; + +The legacy bindings were different in this way: + +- #interrupt-cells: The value was 3. + The 1st cell was the group type of the ICU interrupt. Possible + group types were: + ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure + ICU_GRP_SR (0x1) : Shared peripheral interrupt, secure + ICU_GRP_SEI (0x4) : System error interrupt + ICU_GRP_REI (0x5) : RAM error interrupt + The 2nd cell was the index of the interrupt in the ICU unit. + The 3rd cell was the type of the interrupt. See arm,gic.txt for + details. + +Example: + +icu: interrupt-controller@1e0000 { + compatible = "marvell,cp110-icu"; + reg = <0x1e0000 0x440>; + #interrupt-cells = <3>; interrupt-controller; msi-parent = <&gicp>; }; -usb3h0: usb3@500000 { +node1 { interrupt-parent = <&icu>; interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt new file mode 100644 index 000000000000..0beafed502f5 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,sei.txt @@ -0,0 +1,36 @@ +Marvell SEI (System Error Interrupt) Controller +----------------------------------------------- + +Marvell SEI (System Error Interrupt) controller is an interrupt +aggregator. It receives interrupts from several sources and aggregates +them to a single interrupt line (an SPI) on the parent interrupt +controller. + +This interrupt controller can handle up to 64 SEIs, a set comes from the +AP and is wired while a second set comes from the CPs by the mean of +MSIs. + +Required properties: + +- compatible: should be one of: + * "marvell,ap806-sei" +- reg: SEI registers location and length. +- interrupts: identifies the parent IRQ that will be triggered. +- #interrupt-cells: number of cells to define an SEI wired interrupt + coming from the AP, should be 1. The cell is the IRQ + number. +- interrupt-controller: identifies the node as an interrupt controller + for AP interrupts. +- msi-controller: identifies the node as an MSI controller for the CPs + interrupts. + +Example: + + sei: interrupt-controller@3f0200 { + compatible = "marvell,ap806-sei"; + reg = <0x3f0200 0x40>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + interrupt-controller; + msi-controller; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index a046ed374d80..8de96a4fb2d5 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -2,10 +2,12 @@ DT bindings for the R-Mobile/R-Car/RZ/G interrupt controller Required properties: -- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback. +- compatible: must be "renesas,irqc-<soctype>" or "renesas,intc-ex-<soctype>", + and "renesas,irqc" as fallback. Examples with soctypes are: - "renesas,irqc-r8a73a4" (R-Mobile APE6) - "renesas,irqc-r8a7743" (RZ/G1M) + - "renesas,irqc-r8a7744" (RZ/G1N) - "renesas,irqc-r8a7745" (RZ/G1E) - "renesas,irqc-r8a77470" (RZ/G1C) - "renesas,irqc-r8a7790" (R-Car H2) @@ -19,6 +21,7 @@ Required properties: - "renesas,intc-ex-r8a77965" (R-Car M3-N) - "renesas,intc-ex-r8a77970" (R-Car V3M) - "renesas,intc-ex-r8a77980" (R-Car V3H) + - "renesas,intc-ex-r8a77990" (R-Car E3) - "renesas,intc-ex-r8a77995" (R-Car D3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory diff --git a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt index b0a8af51c388..265b223cd978 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt @@ -11,7 +11,7 @@ The RISC-V supervisor ISA manual specifies three interrupt sources that are attached to every HLIC: software interrupts, the timer interrupt, and external interrupts. Software interrupts are used to send IPIs between cores. The timer interrupt comes from an architecturally mandated real-time timer that is -controller via Supervisor Binary Interface (SBI) calls and CSR reads. External +controlled via Supervisor Binary Interface (SBI) calls and CSR reads. External interrupts connect all other device interrupts to the HLIC, which are routed via the platform-level interrupt controller (PLIC). @@ -25,7 +25,15 @@ in the system. Required properties: - compatible : "riscv,cpu-intc" -- #interrupt-cells : should be <1> +- #interrupt-cells : should be <1>. The interrupt sources are defined by the + RISC-V supervisor ISA manual, with only the following three interrupts being + defined for supervisor mode: + - Source 1 is the supervisor software interrupt, which can be sent by an SBI + call and is reserved for use by software. + - Source 5 is the supervisor timer interrupt, which can be configured by + SBI calls and implements a one-shot timer. + - Source 9 is the supervisor external interrupt, which chains to all other + device interrupts. - interrupt-controller : Identifies the node as an interrupt controller Furthermore, this interrupt-controller MUST be embedded inside the cpu @@ -38,7 +46,7 @@ An example device tree entry for a HLIC is show below. ... cpu1-intc: interrupt-controller { #interrupt-cells = <1>; - compatible = "riscv,cpu-intc", "sifive,fu540-c000-cpu-intc"; + compatible = "sifive,fu540-c000-cpu-intc", "riscv,cpu-intc"; interrupt-controller; }; }; diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index df5db732138d..6922db598def 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -41,6 +41,8 @@ Required properties: - compatible : must be one of the following string: "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW. "mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW. + "mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses + generation one m4u HW. "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. @@ -51,7 +53,7 @@ Required properties: according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in - dt-binding/memory/mt2701-larb-port.h for mt2701, + dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623 dt-binding/memory/mt2712-larb-port.h for mt2712, and dt-binding/memory/mt8173-larb-port.h for mt8173. diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index c6e2d855fe13..377ee639d103 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -12,6 +12,7 @@ Required Properties: - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. - "renesas,ipmmu-r8a7743" for the R8A7743 (RZ/G1M) IPMMU. + - "renesas,ipmmu-r8a7744" for the R8A7744 (RZ/G1N) IPMMU. - "renesas,ipmmu-r8a7745" for the R8A7745 (RZ/G1E) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. diff --git a/Documentation/devicetree/bindings/leds/leds-an30259a.txt b/Documentation/devicetree/bindings/leds/leds-an30259a.txt new file mode 100644 index 000000000000..6ffb861083c0 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-an30259a.txt @@ -0,0 +1,43 @@ +* Panasonic AN30259A 3-channel LED driver + +The AN30259A is a LED controller capable of driving three LEDs independently. It supports +constant current output and sloping current output modes. The chip is connected over I2C. + +Required properties: + - compatible: Must be "panasonic,an30259a". + - reg: I2C slave address. + - #address-cells: Must be 1. + - #size-cells: Must be 0. + +Each LED is represented as a sub-node of the panasonic,an30259a node. + +Required sub-node properties: + - reg: Pin that the LED is connected to. Must be 1, 2, or 3. + +Optional sub-node properties: + - label: see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@30 { + compatible = "panasonic,an30259a"; + reg = <0x30>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + linux,default-trigger = "heartbeat"; + label = "red:indicator"; + }; + + led@2 { + reg = <2>; + label = "green:indicator"; + }; + + led@3 { + reg = <3>; + label = "blue:indicator"; + }; +}; diff --git a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt index 6e8a9ab0fdae..1232fc9fc709 100644 --- a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt +++ b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt @@ -11,6 +11,7 @@ platforms. "qcom,msm8916-apcs-kpss-global", "qcom,msm8996-apcs-hmss-global" "qcom,msm8998-apcs-hmss-global" + "qcom,qcs404-apcs-apps-global" "qcom,sdm845-apss-shared" - reg: diff --git a/Documentation/devicetree/bindings/media/cedrus.txt b/Documentation/devicetree/bindings/media/cedrus.txt new file mode 100644 index 000000000000..a089a0c1ff05 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cedrus.txt @@ -0,0 +1,54 @@ +Device-tree bindings for the VPU found in Allwinner SoCs, referred to as the +Video Engine (VE) in Allwinner literature. + +The VPU can only access the first 256 MiB of DRAM, that are DMA-mapped starting +from the DRAM base. This requires specific memory allocation and handling. + +Required properties: +- compatible : must be one of the following compatibles: + - "allwinner,sun4i-a10-video-engine" + - "allwinner,sun5i-a13-video-engine" + - "allwinner,sun7i-a20-video-engine" + - "allwinner,sun8i-a33-video-engine" + - "allwinner,sun8i-h3-video-engine" +- reg : register base and length of VE; +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names : should contain "ahb", "mod" and "ram" entries; +- resets : phandle for reset; +- interrupts : VE interrupt number; +- allwinner,sram : SRAM region to use with the VE. + +Optional properties: +- memory-region : CMA pool to use for buffers allocation instead of the + default CMA pool. + +Example: + +reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* Address must be kept in the lower 256 MiBs of DRAM for VE. */ + cma_pool: cma@4a000000 { + compatible = "shared-dma-pool"; + size = <0x6000000>; + alloc-ranges = <0x4a000000 0x6000000>; + reusable; + linux,cma-default; + }; +}; + +video-codec@1c0e000 { + compatible = "allwinner,sun7i-a20-video-engine"; + reg = <0x01c0e000 0x1000>; + + clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>, + <&ccu CLK_DRAM_VE>; + clock-names = "ahb", "mod", "ram"; + + resets = <&ccu RST_VE>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + allwinner,sram = <&ve_sram 1>; +}; diff --git a/Documentation/devicetree/bindings/media/fsl-pxp.txt b/Documentation/devicetree/bindings/media/fsl-pxp.txt new file mode 100644 index 000000000000..2477e7f87381 --- /dev/null +++ b/Documentation/devicetree/bindings/media/fsl-pxp.txt @@ -0,0 +1,26 @@ +Freescale Pixel Pipeline +======================== + +The Pixel Pipeline (PXP) is a memory-to-memory graphics processing engine +that supports scaling, colorspace conversion, alpha blending, rotation, and +pixel conversion via lookup table. Different versions are present on various +i.MX SoCs from i.MX23 to i.MX7. + +Required properties: +- compatible: should be "fsl,<soc>-pxp", where SoC can be one of imx23, imx28, + imx6dl, imx6sl, imx6ul, imx6sx, imx6ull, or imx7d. +- reg: the register base and size for the device registers +- interrupts: the PXP interrupt, two interrupts for imx6ull and imx7d. +- clock-names: should be "axi" +- clocks: the PXP AXI clock + +Example: + +pxp@21cc000 { + compatible = "fsl,imx6ull-pxp"; + reg = <0x021cc000 0x4000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "axi"; + clocks = <&clks IMX6UL_CLK_PXP>; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt index 21ffb5ed8183..5dddc95f9cc4 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv748x.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -10,7 +10,11 @@ Required Properties: - "adi,adv7481" for the ADV7481 - "adi,adv7482" for the ADV7482 - - reg: I2C slave address + - reg: I2C slave addresses + The ADV748x has up to twelve 256-byte maps that can be accessed via the + main I2C ports. Each map has it own I2C address and acts as a standard + slave device on the I2C bus. The main address is mandatory, others are + optional and remain at default values if not specified. Optional Properties: @@ -18,6 +22,11 @@ Optional Properties: "intrq3". All interrupts are optional. The "intrq3" interrupt is only available on the adv7481 - interrupts: Specify the interrupt lines for the ADV748x + - reg-names : Names of maps with programmable addresses. + It shall contain all maps needing a non-default address. + Possible map names are: + "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb" The device node must contain one 'port' child node per device input and output port, in accordance with the video interface bindings defined in @@ -47,7 +56,10 @@ Example: video-receiver@70 { compatible = "adi,adv7482"; - reg = <0x70>; + reg = <0x70 0x71 0x72 0x73 0x74 0x75 + 0x60 0x61 0x62 0x63 0x64 0x65>; + reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater", + "infoframe", "cbus", "cec", "sdp", "txa", "txb"; #address-cells = <1>; #size-cells = <0>; @@ -73,7 +85,7 @@ Example: }; }; - port@10 { + port@a { reg = <10>; adv7482_txa: endpoint { @@ -83,7 +95,7 @@ Example: }; }; - port@11 { + port@b { reg = <11>; adv7482_txb: endpoint { diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index dcf57e7c60eb..b3e688b77a38 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -66,7 +66,7 @@ Example: * other maps will retain their default addresses. */ reg = <0x4c>, <0x66>; - reg-names "main", "edid"; + reg-names = "main", "edid"; reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt index c4701f1eaaf6..c4701f1eaaf6 100644 --- a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt +++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807-vcm.txt diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt index 3813947b4d4f..044b11913c49 100644 --- a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt +++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt @@ -5,6 +5,7 @@ Mediatek JPEG Decoder is the JPEG decode hardware present in Mediatek SoCs Required properties: - compatible : must be one of the following string: "mediatek,mt8173-jpgdec" + "mediatek,mt7623-jpgdec", "mediatek,mt2701-jpgdec" "mediatek,mt2701-jpgdec" - reg : physical base address of the jpeg decoder registers and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 2f420050d57f..d329a4e8ac58 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -11,6 +11,7 @@ on Gen3 platforms to a CSI-2 receiver. - compatible: Must be one or more of the following - "renesas,vin-r8a7743" for the R8A7743 device + - "renesas,vin-r8a7744" for the R8A7744 device - "renesas,vin-r8a7745" for the R8A7745 device - "renesas,vin-r8a7778" for the R8A7778 device - "renesas,vin-r8a7779" for the R8A7779 device diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt index 8a7a616e9019..3e2a2652eb19 100644 --- a/Documentation/devicetree/bindings/media/renesas,ceu.txt +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt @@ -17,15 +17,19 @@ Required properties: The CEU supports a single parallel input and should contain a single 'port' subnode with a single 'endpoint'. Connection to input devices are modeled according to the video interfaces OF bindings specified in: -Documentation/devicetree/bindings/media/video-interfaces.txt +[1] Documentation/devicetree/bindings/media/video-interfaces.txt Optional endpoint properties applicable to parallel input bus described in the above mentioned "video-interfaces.txt" file are supported. -- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. - If property is not present, default is active high. -- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. - If property is not present, default is active high. +- hsync-active: See [1] for description. If property is not present, + default is active high. +- vsync-active: See [1] for description. If property is not present, + default is active high. +- bus-width: See [1] for description. Accepted values are '8' and '16'. + If property is not present, default is '8'. +- field-even-active: See [1] for description. If property is not present, + an even field is identified by a logic 0 (active-low signal). Example: diff --git a/Documentation/devicetree/bindings/media/rockchip-vpu.txt b/Documentation/devicetree/bindings/media/rockchip-vpu.txt new file mode 100644 index 000000000000..35dc464ad7c8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-vpu.txt @@ -0,0 +1,29 @@ +device-tree bindings for rockchip VPU codec + +Rockchip (Video Processing Unit) present in various Rockchip platforms, +such as RK3288 and RK3399. + +Required properties: +- compatible: value should be one of the following + "rockchip,rk3288-vpu"; + "rockchip,rk3399-vpu"; +- interrupts: encoding and decoding interrupt specifiers +- interrupt-names: should be "vepu" and "vdpu" +- clocks: phandle to VPU aclk, hclk clocks +- clock-names: should be "aclk" and "hclk" +- power-domains: phandle to power domain node +- iommus: phandle to a iommu node + +Example: +SoC-specific DT entry: + vpu: video-codec@ff9a0000 { + compatible = "rockchip,rk3288-vpu"; + reg = <0x0 0xff9a0000 0x0 0x800>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "vepu", "vdpu"; + clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>; + clock-names = "aclk", "hclk"; + power-domains = <&power RK3288_PD_VIDEO>; + iommus = <&vpu_mmu>; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index baf9d9756b3c..f884ada0bffc 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -100,10 +100,12 @@ Optional endpoint properties slave device (data source) by the master device (data sink). In the master mode the data source device is also the source of the synchronization signals. - bus-type: data bus type. Possible values are: - 0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656) 1 - MIPI CSI-2 C-PHY 2 - MIPI CSI1 3 - CCP2 + 4 - MIPI CSI-2 D-PHY + 5 - Parallel + 6 - Bt.656 - bus-width: number of data lines actively used, valid for the parallel busses. - data-shift: on the parallel data busses, if bus-width is used to specify the number of data lines, data-shift can be used to specify which data lines are diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index 615abdd0eb0d..e937ddd871a6 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -17,6 +17,7 @@ Required properties: - compatible : must be one of : "mediatek,mt2701-smi-common" "mediatek,mt2712-smi-common" + "mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common" "mediatek,mt8173-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 083155cdc2a0..94eddcae77ab 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -6,6 +6,7 @@ Required properties: - compatible : must be one of : "mediatek,mt2701-smi-larb" "mediatek,mt2712-smi-larb" + "mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb" "mediatek,mt8173-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. @@ -16,7 +17,7 @@ Required properties: the register. - "smi" : It's the clock for transfer data and command. -Required property for mt2701 and mt2712: +Required property for mt2701, mt2712 and mt7623: - mediatek,larb-id :the hardware id of this larb. Example: diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 9b62831fdf3e..148ef621a5e5 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -76,7 +76,7 @@ Deprecated properties: Also see child specific device properties: Regulator - ../regulator/arizona-regulator.txt Extcon - ../extcon/extcon-arizona.txt - Sound - ../sound/arizona.txt + Sound - ../sound/wlf,arizona.txt Example: diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt index 7c0d6b2f53e4..7f0cd72f47d2 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt @@ -1,6 +1,6 @@ * Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) -Required properties: +Required properties for USART: - compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu" The compatible <chip> indicated will be the first SoC to support an additional mode or an USART new feature. @@ -11,7 +11,13 @@ Required properties: Required elements: "usart" - clocks: phandles to input clocks. -Optional properties: +Required properties for USART in SPI mode: +- #size-cells : Must be <0> +- #address-cells : Must be <1> +- cs-gpios: chipselects (internal cs not supported) +- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h) + +Optional properties in serial mode: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. @@ -62,3 +68,18 @@ Example: dma-names = "tx", "rx"; atmel,fifo-size = <32>; }; + +- SPI mode: + #include <dt-bindings/mfd/at91-usart.h> + + spi0: spi@f001c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart"; + atmel,usart-mode = <AT91_USART_MODE_SPI>; + reg = <0xf001c000 0x100>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&usart0_clk>; + clock-names = "usart"; + cs-gpios = <&pioB 3 0>; + }; diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index 3ca56fdb5ffe..a4b056761eaa 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -1,16 +1,17 @@ -* ROHM BD71837 Power Management Integrated Circuit bindings +* ROHM BD71837 and BD71847 Power Management Integrated Circuit bindings -BD71837MWV is a programmable Power Management IC for powering single-core, -dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for -low BOM cost and compact solution footprint. It integrates 8 Buck -egulators and 7 LDOs to provide all the power rails required by the SoC and -the commonly used peripherals. +BD71837MWV and BD71847MWV are programmable Power Management ICs for powering +single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. They are +optimized for low BOM cost and compact solution footprint. BD71837MWV +integrates 8 Buck regulators and 7 LDOs. BD71847MWV contains 6 Buck regulators +and 6 LDOs. -Datasheet for PMIC is available at: +Datasheet for BD71837 is available at: https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e Required properties: - - compatible : Should be "rohm,bd71837". + - compatible : Should be "rohm,bd71837" for bd71837 + "rohm,bd71847" for bd71847. - reg : I2C slave address. - interrupt-parent : Phandle to the parent interrupt controller. - interrupts : The interrupt line the device is connected to. diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt index ae15ec333542..bc817e984628 100644 --- a/Documentation/devicetree/bindings/mips/mscc.txt +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -41,3 +41,19 @@ Example: compatible = "mscc,ocelot-cpu-syscon", "syscon"; reg = <0x70000000 0x2c>; }; + +o HSIO regs: + +The SoC has a few registers (HSIO) handling miscellaneous functionalities: +configuration and status of PLL5, RCOMP, SyncE, SerDes configurations and +status, SerDes muxing and a thermal sensor. + +Required properties: +- compatible: Should be "mscc,ocelot-hsio", "syscon", "simple-mfd" +- reg : Should contain registers location and length + +Example: + syscon@10d0000 { + compatible = "mscc,ocelot-hsio", "syscon", "simple-mfd"; + reg = <0x10d0000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt index 6611a7c2053a..01fdc33a41d0 100644 --- a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt +++ b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt @@ -9,6 +9,25 @@ blocks that can be used to create functional hardware objects/devices such as network interfaces, crypto accelerator instances, L2 switches, etc. +For an overview of the DPAA2 architecture and fsl-mc bus see: +Documentation/networking/dpaa2/overview.rst + +As described in the above overview, all DPAA2 objects in a DPRC share the +same hardware "isolation context" and a 10-bit value called an ICID +(isolation context id) is expressed by the hardware to identify +the requester. + +The generic 'iommus' property is insufficient to describe the relationship +between ICIDs and IOMMUs, so an iommu-map property is used to define +the set of possible ICIDs under a root DPRC and how they map to +an IOMMU. + +For generic IOMMU bindings, see +Documentation/devicetree/bindings/iommu/iommu.txt. + +For arm-smmu binding, see: +Documentation/devicetree/bindings/iommu/arm,smmu.txt. + Required properties: - compatible @@ -88,14 +107,34 @@ Sub-nodes: Value type: <phandle> Definition: Specifies the phandle to the PHY device node associated with the this dpmac. +Optional properties: + +- iommu-map: Maps an ICID to an IOMMU and associated iommu-specifier + data. + + The property is an arbitrary number of tuples of + (icid-base,iommu,iommu-base,length). + + Any ICID i in the interval [icid-base, icid-base + length) is + associated with the listed IOMMU, with the iommu-specifier + (i - icid-base + iommu-base). Example: + smmu: iommu@5000000 { + compatible = "arm,mmu-500"; + #iommu-cells = <1>; + stream-match-mask = <0x7C00>; + ... + }; + fsl_mc: fsl-mc@80c000000 { compatible = "fsl,qoriq-mc"; reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ msi-parent = <&its>; + /* define map for ICIDs 23-64 */ + iommu-map = <23 &smmu 23 41>; #address-cells = <3>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/misc/lwn-bk4.txt b/Documentation/devicetree/bindings/misc/lwn-bk4.txt new file mode 100644 index 000000000000..d6a8c188c087 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/lwn-bk4.txt @@ -0,0 +1,26 @@ +* Liebherr's BK4 controller external SPI + +A device which handles data acquisition from compatible industrial +peripherals. +The SPI is used for data and management purposes in both master and +slave modes. + +Required properties: + +- compatible : Should be "lwn,bk4" + +Required SPI properties: + +- reg : Should be address of the device chip select within + the controller. + +- spi-max-frequency : Maximum SPI clocking speed of device in Hz, should be + 30MHz at most for the Liebherr's BK4 external bus. + +Example: + +spidev0: spi@0 { + compatible = "lwn,bk4"; + spi-max-frequency = <30000000>; + reg = <0>; +}; diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index f6ddba31cb73..e2effe17f05e 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -15,6 +15,7 @@ Required Properties: - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY For this device it is strongly suggested to include arasan,soc-ctl-syscon. + - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY - reg: From mmc bindings: Register location and length. - clocks: From clock bindings: Handles to clock inputs. - clock-names: From clock bindings: Tuple including "clk_xin" and "clk_ahb" diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt index 7cd8c432d7c8..8a6f87f13114 100644 --- a/Documentation/devicetree/bindings/mmc/jz4740.txt +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -7,6 +7,7 @@ described in mmc.txt. Required properties: - compatible: Should be one of the following: - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4725b-mmc" for the JZ4725B - "ingenic,jz4780-mmc" for the JZ4780 - reg: Should contain the MMC controller registers location and length. - interrupts: Should contain the interrupt specifier of the MMC controller. diff --git a/Documentation/devicetree/bindings/mmc/mmci.txt b/Documentation/devicetree/bindings/mmc/mmci.txt index 03796cf2d3e7..6d3c626e017d 100644 --- a/Documentation/devicetree/bindings/mmc/mmci.txt +++ b/Documentation/devicetree/bindings/mmc/mmci.txt @@ -15,8 +15,11 @@ Required properties: Optional properties: - arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides the ID provided by the HW +- resets : phandle to internal reset line. + Should be defined for sdmmc variant. - vqmmc-supply : phandle to the regulator device tree node, mentioned as the VCCQ/VDD_IO supply in the eMMC/SD specs. +specific for ux500 variant: - st,sig-dir-dat0 : bus signal direction pin used for DAT[0]. - st,sig-dir-dat2 : bus signal direction pin used for DAT[2]. - st,sig-dir-dat31 : bus signal direction pin used for DAT[3] and DAT[1]. @@ -24,6 +27,14 @@ Optional properties: - st,sig-dir-cmd : cmd signal direction pin used for CMD. - st,sig-pin-fbclk : feedback clock signal pin used. +specific for sdmmc variant: +- st,sig-dir : signal direction polarity used for cmd, dat0 dat123. +- st,neg-edge : data & command phase relation, generated on + sd clock falling edge. +- st,use-ckin : use ckin pin from an external driver to sample + the receive data (example: with voltage + switch transceiver). + Deprecated properties: - mmc-cap-mmc-highspeed : indicates whether MMC is high speed capable. - mmc-cap-sd-highspeed : indicates whether SD is high speed capable. diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index f33467a54a05..f5bcda3980cc 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -10,6 +10,7 @@ Required properties: - compatible: value should be either of the following. "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135 "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173 + "mediatek,mt8183-mmc": for mmc host ip compatible with mt8183 "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701 "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712 "mediatek,mt7622-mmc": for MT7622 SoC @@ -22,6 +23,7 @@ Required properties: "source" - source clock (required) "hclk" - HCLK which used for host (required) "source_cg" - independent source clock gate (required for MT2712) + "bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3) - pinctrl-names: should be "default", "state_uhs" - pinctrl-0: should contain default/high speed pin ctrl - pinctrl-1: should contain uhs mode pin ctrl diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index 9bce57862ed6..32b4b4e41923 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -38,3 +38,75 @@ sdhci@c8000200 { power-gpios = <&gpio 155 0>; /* gpio PT3 */ bus-width = <8>; }; + +Optional properties for Tegra210 and Tegra186: +- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage + configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" + for controllers supporting multiple voltage levels. The order of names + should correspond to the pin configuration states in pinctrl-0 and + pinctrl-1. +- nvidia,only-1-8-v : The presence of this property indicates that the + controller operates at a 1.8 V fixed I/O voltage. +- nvidia,pad-autocal-pull-up-offset-3v3, + nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength + calibration offsets for 3.3 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-1v8, + nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength + calibration offsets for 1.8 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-3v3-timeout, + nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 3.3 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-1v8-timeout, + nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 1.8 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-sdr104, + nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength + calibration offsets for SDR104 mode. +- nvidia,pad-autocal-pull-up-offset-hs400, + nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength + calibration offsets for HS400 mode. +- nvidia,default-tap : Specify the default inbound sampling clock + trimmer value for non-tunable modes. +- nvidia,default-trim : Specify the default outbound clock trimmer + value. +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing + + Notes on the pad calibration pull up and pulldown offset values: + - The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the + SDHCI_TEGRA_AUTO_CAL_CONFIG register. + - A higher value corresponds to higher drive strength. Please refer + to the reference manual of the SoC for correct values. + - The SDR104 and HS400 timing specific values are used in + corresponding modes if specified. + + Notes on tap and trim values: + - The values are used for compensating trace length differences + by adjusting the sampling point. + - The values are programmed to the Vendor Clock Control Register. + Please refer to the reference manual of the SoC for correct + values. + - The DQS trim values are only used on controllers which support + HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports + HS400. + +Example: +sdhci@700b0000 { + compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; + clock-names = "sdhci"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index 5ff1e12c655a..c064af5838aa 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -12,6 +12,7 @@ Required properties: - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs + - "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs - "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs @@ -23,7 +24,8 @@ Required properties: - interrupts: Some SoCs have only 1 shared interrupt, while others have either 2 or 3 individual interrupts (error, int, card detect). Below is the number of interrupts for each SoC: - 1: r8a73a4, r8a7743, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, r8a7794 + 1: r8a73a4, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, r8a7793, + r8a7794 2: r8a7740, sh73a0 3: r7s72100 diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt new file mode 100644 index 000000000000..45c9978aad7b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt @@ -0,0 +1,41 @@ +* Spreadtrum SDHCI controller (sdhci-sprd) + +The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface +for MMC, SD and SDIO types of cards. + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-sprd driver. + +Required properties: +- compatible: Should contain "sprd,sdhci-r11". +- reg: physical base address of the controller and length. +- interrupts: Interrupts used by the SDHCI controller. +- clocks: Should contain phandle for the clock feeding the SDHCI controller +- clock-names: Should contain the following: + "sdio" - SDIO source clock (required) + "enable" - gate clock which used for enabling/disabling the device (required) + +Optional properties: +- assigned-clocks: the same with "sdio" clock +- assigned-clock-parents: the default parent of "sdio" clock + +Examples: + +sdio0: sdio@20600000 { + compatible = "sprd,sdhci-r11"; + reg = <0 0x20600000 0 0x1000>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + + clock-names = "sdio", "enable"; + clocks = <&ap_clk CLK_EMMC_2X>, + <&apahb_gate CLK_EMMC_EB>; + assigned-clocks = <&ap_clk CLK_EMMC_2X>; + assigned-clock-parents = <&rpll CLK_RPLL_390M>; + + bus-width = <8>; + non-removable; + no-sdio; + no-sd; + cap-mmc-hw-reset; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index c434200d19d5..27f2eab2981d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -16,7 +16,11 @@ Required properties: "renesas,sdhi-r8a73a4" - SDHI IP on R8A73A4 SoC "renesas,sdhi-r8a7740" - SDHI IP on R8A7740 SoC "renesas,sdhi-r8a7743" - SDHI IP on R8A7743 SoC + "renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC "renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC + "renesas,sdhi-r8a774a1" - SDHI IP on R8A774A1 SoC + "renesas,sdhi-r8a77470" - SDHI IP on R8A77470 SoC + "renesas,sdhi-mmc-r8a77470" - SDHI/MMC IP on R8A77470 SoC "renesas,sdhi-r8a7778" - SDHI IP on R8A7778 SoC "renesas,sdhi-r8a7779" - SDHI IP on R8A7779 SoC "renesas,sdhi-r8a7790" - SDHI IP on R8A7790 SoC @@ -27,14 +31,16 @@ Required properties: "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77970" - SDHI IP on R8A77970 SoC "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77990" - SDHI IP on R8A77990 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller - "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 or RZ/G1 + "renesas,rcar-gen2-sdhi" - a generic R-Car Gen2 and RZ/G1 SDHI + (not SDHI/MMC) controller + "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 or RZ/G2 SDHI controller - "renesas,rcar-gen3-sdhi" - a generic R-Car Gen3 SDHI controller When compatible with the generic version, nodes must list diff --git a/Documentation/devicetree/bindings/mmc/uniphier-sd.txt b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt new file mode 100644 index 000000000000..e1d658755722 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/uniphier-sd.txt @@ -0,0 +1,55 @@ +UniPhier SD/eMMC controller + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-sd-v2.91" - IP version 2.91 + "socionext,uniphier-sd-v3.1" - IP version 3.1 + "socionext,uniphier-sd-v3.1.1" - IP version 3.1.1 +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: a single clock specifier of the controller clock. +- reset-names: should contain the following: + "host" - mandatory for all versions + "bridge" - should exist only for "socionext,uniphier-sd-v2.91" + "hw" - should exist if eMMC hw reset line is available +- resets: a list of reset specifiers, corresponding to the reset-names + +Optional properties: +- pinctrl-names: if present, should contain the following: + "default" - should exist for all instances + "uhs" - should exist for SD instance with UHS support +- pinctrl-0: pin control state for the default mode +- pinctrl-1: pin control state for the UHS mode +- dma-names: should be "rx-tx" if present. + This property can exist only for "socionext,uniphier-sd-v2.91". +- dmas: a single DMA channel specifier + This property can exist only for "socionext,uniphier-sd-v2.91". +- bus-width: see mmc.txt +- cap-sd-highspeed: see mmc.txt +- cap-mmc-highspeed: see mmc.txt +- sd-uhs-sdr12: see mmc.txt +- sd-uhs-sdr25: see mmc.txt +- sd-uhs-sdr50: see mmc.txt +- cap-mmc-hw-reset: should exist if reset-names contains "hw". see mmc.txt +- non-removable: see mmc.txt + +Example: + + sd: sdhc@5a400000 { + compatible = "socionext,uniphier-sd-v2.91"; + reg = <0x5a400000 0x200>; + interrupts = <0 76 4>; + pinctrl-names = "default", "uhs"; + pinctrl-0 = <&pinctrl_sd>; + pinctrl-1 = <&pinctrl_sd_uhs>; + clocks = <&mio_clk 0>; + reset-names = "host", "bridge"; + resets = <&mio_rst 0>, <&mio_rst 3>; + dma-names = "rx-tx"; + dmas = <&dmac 4>; + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt index 4648948f7c3b..e15589f47787 100644 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -19,6 +19,9 @@ Optional properties: - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed to this hardware block, or must be "mdio_done" for the first interrupt and "mdio_error" for the second when there are separate interrupts +- clocks: A reference to the clock supplying the MDIO bus controller +- clock-frequency: the MDIO bus clock that must be output by the MDIO bus + hardware, if absent, the default hardware values are used Child nodes of this MDIO bus controller node are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt index 94a7f33ac5e9..cc4372842bf3 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_can.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -3,6 +3,7 @@ Renesas R-Car CAN controller Device Tree Bindings Required properties: - compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC. + "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC. "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 41089369f891..b3acebe08eb0 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -19,6 +19,10 @@ Required properties: - slaves : Specifies number for slaves - active_slave : Specifies the slave to use for time stamping, ethtool and SIOCGMIIPHY +- cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection + device. See also cpsw-phy-sel.txt for it's binding. + Note that in legacy cases cpsw-phy-sel may be + a child device instead of a phandle. Optional properties: - ti,hwmods : Must be "cpgmac0" @@ -75,6 +79,7 @@ Examples: cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; @@ -103,6 +108,7 @@ Examples: cpts_clock_mult = <0x80000000>; cpts_clock_shift = <29>; syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 1811e1972a7a..5201bc15fdd6 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -46,6 +46,42 @@ Required properties: "brcm,bcm6328-switch" "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" +Required properties for BCM585xx/586xx/88312 SoCs: + + - reg: a total of 3 register base addresses, the first one must be the + Switch Register Access block base, the second is the port 5/4 mux + configuration register and the third one is the SGMII configuration + and status register base address. + + - interrupts: a total of 13 interrupts must be specified, in the following + order: port 0-5, 7-8 link status change, then the integrated PHY interrupt, + then the timestamping interrupt and the sleep timer interrupts for ports + 5,7,8. + +Optional properties for BCM585xx/586xx/88312 SoCs: + + - reg-names: a total of 3 names matching the 3 base register address, must + be in the following order: + "srab" + "mux_config" + "sgmii_config" + + - interrupt-names: a total of 13 names matching the 13 interrupts specified + must be in the following order: + "link_state_p0" + "link_state_p1" + "link_state_p2" + "link_state_p3" + "link_state_p4" + "link_state_p5" + "link_state_p7" + "link_state_p8" + "phy" + "ts" + "imp_sleep_timer_p5" + "imp_sleep_timer_p7" + "imp_sleep_timer_p8" + See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt new file mode 100644 index 000000000000..886cbe8ffb38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt @@ -0,0 +1,143 @@ +Lantiq GSWIP Ethernet switches +================================== + +Required properties for GSWIP core: + +- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the + xRX200 SoC +- reg : memory range of the GSWIP core registers + : memory range of the GSWIP MDIO registers + : memory range of the GSWIP MII registers + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of +additional required and optional properties. + + +Required properties for MDIO bus: +- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP + core of the xRX200 SoC and the PHYs connected to it. + +See Documentation/devicetree/bindings/net/mdio.txt for a list of additional +required and optional properties. + + +Required properties for GPHY firmware loading: +- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw" + "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw" + for the loading of the firmware into the embedded + GPHY core of the SoC. +- lantiq,rcu : reference to the rcu syscon + +The GPHY firmware loader has a list of GPHY entries, one for each +embedded GPHY + +- reg : Offset of the GPHY firmware register in the RCU + register range +- resets : list of resets of the embedded GPHY +- reset-names : list of names of the resets + +Example: + +Ethernet switch on the VRX200 SoC: + +switch@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-gswip"; + reg = < 0xe108000 0x3100 /* switch */ + 0xe10b100 0xd8 /* mdio */ + 0xe10b1d8 0x130 /* mii */ + >; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + + port@4 { + reg = <4>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&phy13>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + + port@6 { + reg = <0x6>; + label = "cpu"; + ethernet = <ð0>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + }; + }; + + gphy-fw { + compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"; + lantiq,rcu = <&rcu0>; + #address-cells = <1>; + #size-cells = <0>; + + gphy@20 { + reg = <0x20>; + + resets = <&reset0 31 30>; + reset-names = "gphy"; + }; + + gphy@68 { + reg = <0x68>; + + resets = <&reset0 29 28>; + reset-names = "gphy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt new file mode 100644 index 000000000000..5ff5e68bbbb6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt @@ -0,0 +1,21 @@ +Lantiq xRX200 GSWIP PMAC Ethernet driver +================================== + +Required properties: + +- compatible : "lantiq,xrx200-net" for the PMAC of the embedded + : GSWIP in the xXR200 +- reg : memory range of the PMAC core inside of the GSWIP core +- interrupts : TX and RX DMA interrupts. Use interrupt-names "tx" for + : the TX interrupt and "rx" for the RX interrupt. + +Example: + +ethernet@e10b308 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = <0xe10b308 0xcf8>; + interrupts = <73>, <72>; + interrupt-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 457d5ae16f23..3e17ac1d5d58 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -10,6 +10,7 @@ Required properties: Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. + Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt index c329608fa887..83370ebf5b89 100644 --- a/Documentation/devicetree/bindings/net/marvell,prestera.txt +++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt @@ -2,7 +2,7 @@ Marvell Prestera Switch Chip bindings ------------------------------------- Required properties: -- compatible: one of the following +- compatible: must be "marvell,prestera" and one of the following "marvell,prestera-98dx3236", "marvell,prestera-98dx3336", "marvell,prestera-98dx4251", @@ -21,7 +21,7 @@ switch { ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>; packet-processor@0 { - compatible = "marvell,prestera-98dx3236"; + compatible = "marvell,prestera-98dx3236", "marvell,prestera"; reg = <0 0x4000000>; interrupts = <33>, <34>, <35>; dfx = <&dfx>; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index fc019df0d863..b78397669320 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -31,7 +31,7 @@ required. Required properties (port): -- interrupts: interrupt for the port +- interrupts: interrupt(s) for the port - port-id: ID of the port from the MAC point of view - gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the GOP (Group Of Ports) point of view. This ID is used to index the @@ -43,10 +43,12 @@ Optional properties (port): - marvell,loopback: port is loopback mode - phy: a phandle to a phy node defining the PHY address (as the reg property, a single integer). -- interrupt-names: if more than a single interrupt for rx is given, must - be the name associated to the interrupts listed. Valid - names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", - "rx-shared", "link". +- interrupt-names: if more than a single interrupt for is given, must be the + name associated to the interrupts listed. Valid names are: + "hifX", with X in [0..8], and "link". The names "tx-cpu0", + "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported + for backward compatibility but shouldn't be used for new + additions. - marvell,system-controller: a phandle to the system controller. Example for marvell,armada-375-pp2: @@ -89,9 +91,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <0>; gop-port-id = <0>; }; @@ -101,9 +108,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <1>; gop-port-id = <2>; }; @@ -113,9 +125,14 @@ cpm_ethernet: ethernet@0 { <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, - <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared"; + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4", + "hif5", "hif6", "hif7", "hif8", "link"; port-id = <2>; gop-port-id = <3>; }; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index e22d8cfea687..5100358177c9 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -1,4 +1,4 @@ -Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY +Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY Some boards require special tuning values, particularly when it comes to clock delays. You can specify clock delay values in the PHY OF @@ -64,6 +64,32 @@ KSZ9031: Attention: The link partner must be configurable as slave otherwise no link will be established. +KSZ9131: + + All skew control options are specified in picoseconds. The increment + step is 100ps. Unlike KSZ9031, the values represent picoseccond delays. + A negative value can be assigned as rxc-skew-psec = <(-100)>;. + + Optional properties: + + Range of the value -700 to 2400, default value 0: + + - rxc-skew-psec : Skew control of RX clock pad + - txc-skew-psec : Skew control of TX clock pad + + Range of the value -700 to 800, default value 0: + + - rxdv-skew-psec : Skew control of RX CTL pad + - txen-skew-psec : Skew control of TX CTL pad + - rxd0-skew-psec : Skew control of RX data 0 pad + - rxd1-skew-psec : Skew control of RX data 1 pad + - rxd2-skew-psec : Skew control of RX data 2 pad + - rxd3-skew-psec : Skew control of RX data 3 pad + - txd0-skew-psec : Skew control of TX data 0 pad + - txd1-skew-psec : Skew control of TX data 1 pad + - txd2-skew-psec : Skew control of TX data 2 pad + - txd3-skew-psec : Skew control of TX data 3 pad + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt index 0a84711abece..9e5c17d426ce 100644 --- a/Documentation/devicetree/bindings/net/mscc-ocelot.txt +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -12,7 +12,6 @@ Required properties: - "sys" - "rew" - "qs" - - "hsio" - "qsys" - "ana" - "portX" with X from 0 to the number of last port index available on that @@ -45,7 +44,6 @@ Example: reg = <0x1010000 0x10000>, <0x1030000 0x10000>, <0x1080000 0x100>, - <0x10d0000 0x10000>, <0x11e0000 0x100>, <0x11f0000 0x100>, <0x1200000 0x100>, @@ -59,10 +57,9 @@ Example: <0x1280000 0x100>, <0x1800000 0x80000>, <0x1880000 0x10000>; - reg-names = "sys", "rew", "qs", "hsio", "port0", - "port1", "port2", "port3", "port4", "port5", - "port6", "port7", "port8", "port9", "port10", - "qsys", "ana"; + reg-names = "sys", "rew", "qs", "port0", "port1", "port2", + "port3", "port4", "port5", "port6", "port7", + "port8", "port9", "port10", "qsys", "ana"; interrupts = <21 22>; interrupt-names = "xtr", "inj"; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 0eedabe22cc3..5ff37c68c941 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -1,10 +1,5 @@ * Microsemi - vsc8531 Giga bit ethernet phy -Required properties: -- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" - The PHY device uses the binding described in - Documentation/devicetree/bindings/net/phy.txt - Optional properties: - vsc8531,vddmac : The vddmac in mV. Allowed values is listed in the first row of Table 1 (below). @@ -27,14 +22,16 @@ Optional properties: 'vddmac'. Default value is 0%. Ref: Table:1 - Edge rate change (below). -- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. - Allowed values are define in - "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_1000_ACTIVITY (1). -- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. - Allowed values are define in +- vsc8531,led-[N]-mode : LED mode. Specify how the LED[N] should behave. + N depends on the number of LEDs supported by a + PHY. + Allowed values are defined in "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_100_ACTIVITY (2). + Default values are VSC8531_LINK_1000_ACTIVITY (1), + VSC8531_LINK_100_ACTIVITY (2), + VSC8531_LINK_ACTIVITY (0) and + VSC8531_DUPLEX_COLLISION (8). + Table: 1 - Edge rate change ----------------------------------------------------------------| diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index da249b7c406c..3530256a879c 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,6 +6,7 @@ interface contains. Required properties: - compatible: Must contain one or more of the following: - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7744" for the R8A7744 SoC. - "renesas,etheravb-r8a7745" for the R8A7745 SoC. - "renesas,etheravb-r8a77470" for the R8A77470 SoC. - "renesas,etheravb-r8a7790" for the R8A7790 SoC. diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 76db9f13ad96..abc36274227c 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -16,6 +16,7 @@ Required properties: "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. + "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC. "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 device. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 7fd4e8ce4149..2196d1ab3c8c 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -56,6 +56,11 @@ Optional properties: the length can vary between hw versions. - <supply-name>-supply: handle to the regulator device tree node optional "supply-name" is "vdd-0.8-cx-mx". +- memory-region: + Usage: optional + Value type: <phandle> + Definition: reference to the reserved-memory for the msa region + used by the wifi firmware running in Q6. Example (to supply the calibration data alone): @@ -149,4 +154,5 @@ wifi@18000000 { <0 140 0 /* CE10 */ >, <0 141 0 /* CE11 */ >; vdd-0.8-cx-mx-supply = <&pm8998_l5>; + memory-region = <&wifi_msa_mem>; }; diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt index e319fe5e205a..99c4ba6a3f61 100644 --- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt +++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt @@ -7,6 +7,7 @@ Required properties: "allwinner,sun8i-a83t-sid" "allwinner,sun8i-h3-sid" "allwinner,sun50i-a64-sid" + "allwinner,sun50i-h5-sid" - reg: Should contain registers location and length diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index cb33421184a0..f37494d5a7be 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -50,6 +50,7 @@ Additional required properties for imx7d-pcie: - reset-names: Must contain the following entires: - "pciephy" - "apps" + - "turnoff" Example: diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 4dd17de549a7..2030ee0dc4f9 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -19,6 +19,9 @@ pcie_msi_intc : Interrupt controller device node for MSI IRQ chip interrupt-cells: should be set to 1 interrupts: GIC interrupt lines connected to PCI MSI interrupt lines +ti,syscon-pcie-id : phandle to the device control module required to set device + id and vendor id. + Example: pcie_msi_intc: msi-interrupt-controller { interrupt-controller; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 9fe7e12a7bf3..b94078f58d8e 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -7,6 +7,7 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7743" for the R8A7743 SoC; + "renesas,pci-r8a7744" for the R8A7744 SoC; "renesas,pci-r8a7745" for the R8A7745 SoC; "renesas,pci-r8a7790" for the R8A7790 SoC; "renesas,pci-r8a7791" for the R8A7791 SoC; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index a5f7fc62d10e..976ef7bfff93 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -2,6 +2,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; + "renesas,pcie-r8a7744" for the R8A7744 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; @@ -9,6 +10,7 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7795" for the R8A7795 SoC; "renesas,pcie-r8a7796" for the R8A7796 SoC; "renesas,pcie-r8a77980" for the R8A77980 SoC; + "renesas,pcie-r8a77990" for the R8A77990 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 7f7af3044016..452fe48c4fdd 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -26,6 +26,11 @@ HOST MODE ranges, interrupt-map-mask, interrupt-map : as specified in ../designware-pcie.txt + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. DEVICE MODE =========== diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 0aced97d8092..b640845fec67 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -8,6 +8,7 @@ Required properties: "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" "brcm,iproc-sr-sata-phy" + "brcm,bcm63138-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - reg: register ranges for the PHY PCB interface diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt new file mode 100644 index 000000000000..7f49fd54ebc1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt @@ -0,0 +1,30 @@ +Cadence MHDP DisplayPort SD0801 PHY binding +=========================================== + +This binding describes the Cadence SD0801 PHY hardware included with +the Cadence MHDP DisplayPort controller. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be "cdns,dp-phy" +- reg : Defines the following sets of registers in the parent + mhdp device: + - Offset of the DPTX PHY configuration registers + - Offset of the SD0801 PHY configuration registers +- #phy-cells : from the generic PHY bindings, must be 0. + +Optional properties: +- num_lanes : Number of DisplayPort lanes to use (1, 2 or 4) +- max_bit_rate : Maximum DisplayPort link bit rate to use, in Mbps (2160, + 2430, 2700, 3240, 4320, 5400 or 8100) +------------------------------------------------------------------------------- + +Example: + dp_phy: phy@f0fb030a00 { + compatible = "cdns,dp-phy"; + reg = <0xf0 0xfb030a00 0x0 0x00000040>, + <0xf0 0xfb500000 0x0 0x00100000>; + num_lanes = <4>; + max_bit_rate = <8100>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt new file mode 100644 index 000000000000..332219860187 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ocelot-serdes.txt @@ -0,0 +1,43 @@ +Microsemi Ocelot SerDes muxing driver +------------------------------------- + +On Microsemi Ocelot, there is a handful of registers in HSIO address +space for setting up the SerDes to switch port muxing. + +A SerDes X can be "muxed" to work with switch port Y or Z for example. +One specific SerDes can also be used as a PCIe interface. + +Hence, a SerDes represents an interface, be it an Ethernet or a PCIe one. + +There are two kinds of SerDes: SERDES1G supports 10/100Mbps in +half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports +10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode. + +Also, SERDES6G number (aka "macro") 0 is the only interface supporting +QSGMII. + +This is a child of the HSIO syscon ("mscc,ocelot-hsio", see +Documentation/devicetree/bindings/mips/mscc.txt) on the Microsemi Ocelot. + +Required properties: + +- compatible: should be "mscc,vsc7514-serdes" +- #phy-cells : from the generic phy bindings, must be 2. + The first number defines the input port to use for a given + SerDes macro. The second defines the macro to use. They are + defined in dt-bindings/phy/phy-ocelot-serdes.h + +Example: + + serdes: serdes { + compatible = "mscc,vsc7514-serdes"; + #phy-cells = <2>; + }; + + ethernet { + port1 { + phy-handle = <&phy_foo>; + /* Link SERDES1G_5 to port1 */ + phys = <&serdes 1 SERDES1G_5>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt new file mode 100644 index 000000000000..710cccd5ee56 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt @@ -0,0 +1,43 @@ +ROCKCHIP HDMI PHY WITH INNO IP BLOCK + +Required properties: + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-hdmi-phy", + * "rockchip,rk3328-hdmi-phy"; + - reg : Address and length of the hdmi phy control register set + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must contain "sysclk" for system + control and register configuration, "refoclk" for crystal- + oscillator reference PLL clock input and "refpclk" for pclk- + based refeference PLL clock input. + - #clock-cells: should be 0. + - clock-output-names : shall be the name for the output clock. + - interrupts : phandle + interrupt specified for the hdmiphy interrupt + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + +Optional properties for rk3328-hdmi-phy: + - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse + - nvmem-cell-names : "cpu-version" to read the chip version, required + for adjustment to some frequency settings + +Example: + hdmi_phy: hdmi-phy@12030000 { + compatible = "rockchip,rk3228-hdmi-phy"; + reg = <0x12030000 0x10000>; + #phy-cells = <0>; + clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>; + clock-names = "sysclk", "refoclk", "refpclk"; + #clock-cells = <0>; + clock-output-names = "hdmi_phy"; + status = "disabled"; + }; + +Then the PHY can be used in other nodes such as: + + hdmi: hdmi@200a0000 { + compatible = "rockchip,rk3228-dw-hdmi"; + ... + phys = <&hdmi_phy>; + phy-names = "hdmi"; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index 0c7629e88bf3..adf20b2bdf71 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -10,16 +10,20 @@ Required properties: "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, - "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845, + "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845. - - reg: - - For "qcom,sdm845-qmp-usb3-phy": - - index 0: address and length of register set for PHY's common serdes - block. - - named register "dp_com" (using reg-names): address and length of the - DP_COM control block. - - For all others: - - offset and length of register set for PHY's common serdes block. +- reg: + - index 0: address and length of register set for PHY's common + serdes block. + - index 1: address and length of the DP_COM control block (for + "qcom,sdm845-qmp-usb3-phy" only). + +- reg-names: + - For "qcom,sdm845-qmp-usb3-phy": + - Should be: "reg-base", "dp_com" + - For all others: + - The reg-names property shouldn't be defined. - #clock-cells: must be 1 - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe @@ -35,6 +39,7 @@ Required properties: "aux" for phy aux clock, "ref" for 19.2 MHz ref clk, "com_aux" for phy common block aux clock, + "ref_aux" for phy reference aux clock, For "qcom,msm8996-qmp-pcie-phy" must contain: "aux", "cfg_ahb", "ref". For "qcom,msm8996-qmp-usb3-phy" must contain: diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index eeb9e1874ea6..4f0879a0ca12 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -5,6 +5,7 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743 SoC. + "renesas,usb-phy-r8a7744" if the device is a part of R8A7744 SoC. "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC. "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index fb4a204da2bf..de7b5393c163 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -1,10 +1,12 @@ * Renesas R-Car generation 3 USB 2.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 2.0 PHY contains. +3 and RZ/G2 USB 2.0 PHY contain. Required properties: -- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 +- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1 + SoC. + "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 SoC. @@ -14,7 +16,8 @@ Required properties: R8A77990 SoC. "renesas,usb2-phy-r8a77995" if the device is a part of an R8A77995 SoC. - "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first @@ -31,6 +34,8 @@ channel as USB OTG: - interrupts: interrupt specifier for the PHY. - vbus-supply: Phandle to a regulator that provides power to the VBUS. This regulator will be managed during the PHY power on/off sequence. +- renesas,no-otg-pins: boolean, specify when a board does not provide proper + otg pins. Example (R-Car H3): diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt index 47dd296ecead..9d9826609c2f 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -1,20 +1,22 @@ * Renesas R-Car generation 3 USB 3.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 3.0 PHY contains. +3 and RZ/G2 USB 3.0 PHY contain. If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL instead of USB3_CLK. However, if you don't want to these features, you don't need this driver. Required properties: -- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 +- compatible: "renesas,r8a774a1-usb3-phy" if the device is a part of an R8A774A1 + SoC. + "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 SoC. "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 SoC. "renesas,r8a77965-usb3-phy" if the device is a part of an R8A77965 SoC. - "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible - device. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt new file mode 100644 index 000000000000..1889d3b89d68 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt @@ -0,0 +1,31 @@ +Socionext UniPhier PCIe PHY bindings + +This describes the devicetree bindings for PHY interface built into +PCIe controller implemented on Socionext UniPhier SoCs. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY + "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Must be zero. +- clocks: A phandle to the clock gate for PCIe glue layer including + this phy. +- resets: A phandle to the reset line for PCIe glue layer including + this phy. + +Optional properties: +- socionext,syscon: A phandle to system control to set configurations + for phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + pcie_phy: phy@66038000 { + compatible = "socionext,uniphier-ld20-pcie-phy"; + reg = <0x66038000 0x4000>; + #phy-cells = <0>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + socionext,syscon = <&soc_glue>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt new file mode 100644 index 000000000000..b43b28250cc0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt @@ -0,0 +1,45 @@ +Socionext UniPhier USB2 PHY + +This describes the devicetree bindings for PHY interface built into +USB2 controller implemented on Socionext UniPhier SoCs. + +Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3 +controller doesn't include its own High-Speed PHY. This needs to specify +USB2 PHY instead of USB3 HS-PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb2-phy" - for Pro4 SoC + "socionext,uniphier-ld11-usb2-phy" - for LD11 SoC + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- #phy-cells: Should be 0. +- reg: The number of the PHY. + +Sub-nodes optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + soc-glue@5f800000 { + ... + usb-phy { + compatible = "socionext,uniphier-ld11-usb2-phy"; + usb_phy0: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + ... + }; + }; + + usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + ... + phy-names = "usb"; + phys = <&usb_phy0>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt new file mode 100644 index 000000000000..e8d8086a7ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt @@ -0,0 +1,69 @@ +Socionext UniPhier USB3 High-Speed (HS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about High-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. +- nvmem-cells: Phandles to nvmem cell that contains the trimming data. + Available only for HS-PHY implemented on LD20 and PXs3, and + if unspecified, default value is used. +- nvmem-cell-names: Should be the following names, which correspond to + each nvmem-cells. + All of the 3 parameters associated with the following names are + required for each port, if any one is omitted, the trimming data + of the port will not be set at all. + "rterm", "sel_t", "hs_i" - Each cell name for phy parameters + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_hsphy0: hs-phy@200 { + compatible = "socionext,uniphier-ld20-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + nvmem-cell-names = "rterm", "sel_t", "hs_i"; + nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, + <&usb_hs_i0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt new file mode 100644 index 000000000000..490b815445e8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt @@ -0,0 +1,57 @@ +Socionext UniPhier USB3 Super-Speed (SS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about Super-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_ssphy0: ss-phy@300 { + compatible = "socionext,uniphier-ld20-usb3-ssphy"; + reg = <0x300 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt new file mode 100644 index 000000000000..4fa9539070cb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm4708-pinmux.txt @@ -0,0 +1,57 @@ +Broadcom Northstar pins mux controller + +Some of Northstar SoCs's pins can be used for various purposes thanks to the mux +controller. This binding allows describing mux controller and listing available +functions. They can be referenced later by other bindings to let system +configure controller correctly. + +A list of pins varies across chipsets so few bindings are available. + +Required properties: +- compatible: must be one of: + "brcm,bcm4708-pinmux" + "brcm,bcm4709-pinmux" + "brcm,bcm53012-pinmux" +- reg: iomem address range of CRU (Central Resource Unit) pin registers +- reg-names: "cru_gpio_control" - the only needed & supported reg right now + +Functions and their groups available for all chipsets: +- "spi": "spi_grp" +- "i2c": "i2c_grp" +- "pwm": "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp" +- "uart1": "uart1_grp" + +Additionally available on BCM4709 and BCM53012: +- "mdio": "mdio_grp" +- "uart2": "uart2_grp" +- "sdio": "sdio_pwr_grp", "sdio_1p8v_grp" + +For documentation of subnodes see: +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + dmu@1800c000 { + compatible = "simple-bus"; + ranges = <0 0x1800c000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + cru@100 { + compatible = "simple-bus"; + reg = <0x100 0x1a4>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + + pin-controller@1c0 { + compatible = "brcm,bcm4708-pinmux"; + reg = <0x1c0 0x24>; + reg-names = "cru_gpio_control"; + + spi-pins { + function = "spi"; + groups = "spi_grp"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt index ca313a7aeaff..af20b0ec715c 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt @@ -20,16 +20,30 @@ Required properties: - compatible: One of: - "ingenic,jz4740-pinctrl" + - "ingenic,jz4725b-pinctrl" - "ingenic,jz4770-pinctrl" - "ingenic,jz4780-pinctrl" - reg: Address range of the pinctrl registers. -GPIO sub-nodes --------------- +Required properties for sub-nodes (GPIO chips): +----------------------------------------------- -The pinctrl node can have optional sub-nodes for the Ingenic GPIO driver; -please refer to ../gpio/ingenic,gpio.txt. + - compatible: Must contain one of: + - "ingenic,jz4740-gpio" + - "ingenic,jz4770-gpio" + - "ingenic,jz4780-gpio" + - reg: The GPIO bank number. + - interrupt-controller: Marks the device node as an interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + - #interrupt-cells: Should be 2. Refer to + ../interrupt-controller/interrupts.txt for more details. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. Refer to + ../gpio/gpio.txt for more details. Example: @@ -38,4 +52,21 @@ Example: pinctrl: pin-controller@10010000 { compatible = "ingenic,jz4740-pinctrl"; reg = <0x10010000 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + gpa: gpio@0 { + compatible = "ingenic,jz4740-gpio"; + reg = <0>; + + gpio-controller; + gpio-ranges = <&pinctrl 0 0 32>; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&intc>; + interrupts = <28>; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 54ecb8ab7788..82ead40311f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -13,6 +13,8 @@ Required properties for the root node: "amlogic,meson-gxl-aobus-pinctrl" "amlogic,meson-axg-periphs-pinctrl" "amlogic,meson-axg-aobus-pinctrl" + "amlogic,meson-g12a-periphs-pinctrl" + "amlogic,meson-g12a-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt new file mode 100644 index 000000000000..83f4bbac94bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,npcm7xx-pinctrl.txt @@ -0,0 +1,216 @@ +Nuvoton NPCM7XX Pin Controllers + +The Nuvoton BMC NPCM7XX Pin Controller multi-function routed through +the multiplexing block, Each pin supports GPIO functionality (GPIOx) +and multiple functions that directly connect the pin to different +hardware blocks. + +Required properties: +- #address-cells : should be 1. +- #size-cells : should be 1. +- compatible : "nuvoton,npcm750-pinctrl" for Poleg NPCM7XX. +- ranges : defines mapping ranges between pin controller node (parent) + to GPIO bank node (children). + +=== GPIO Bank Subnode === + +The NPCM7XX has 8 GPIO Banks each GPIO bank supports 32 GPIO. + +Required GPIO Bank subnode-properties: +- reg : specifies physical base address and size of the GPIO + bank registers. +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Must be <2>. The first cell is the gpio pin number + and the second cell is used for optional parameters. +- interrupts : contain the GPIO bank interrupt with flags for falling edge. +- gpio-ranges : defines the range of pins managed by the GPIO bank controller. + +For example, GPIO bank subnodes like the following: + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + +=== Pin Mux Subnode === + +- pin: A string containing the name of the pin + An array of strings, each string containing the name of a pin. + These pin are used for selecting pin configuration. + +The following are the list of pins available: + "GPIO0/IOX1DI", "GPIO1/IOX1LD", "GPIO2/IOX1CK", "GPIO3/IOX1D0", + "GPIO4/IOX2DI/SMB1DSDA", "GPIO5/IOX2LD/SMB1DSCL", "GPIO6/IOX2CK/SMB2DSDA", + "GPIO7/IOX2D0/SMB2DSCL", "GPIO8/LKGPO1", "GPIO9/LKGPO2", "GPIO10/IOXHLD", + "GPIO11/IOXHCK", "GPIO12/GSPICK/SMB5BSCL", "GPIO13/GSPIDO/SMB5BSDA", + "GPIO14/GSPIDI/SMB5CSCL", "GPIO15/GSPICS/SMB5CSDA", "GPIO16/LKGPO0", + "GPIO17/PSPI2DI/SMB4DEN","GPIO18/PSPI2D0/SMB4BSDA", "GPIO19/PSPI2CK/SMB4BSCL", + "GPIO20/SMB4CSDA/SMB15SDA", "GPIO21/SMB4CSCL/SMB15SCL", "GPIO22/SMB4DSDA/SMB14SDA", + "GPIO23/SMB4DSCL/SMB14SCL", "GPIO24/IOXHDO", "GPIO25/IOXHDI", "GPIO26/SMB5SDA", + "GPIO27/SMB5SCL", "GPIO28/SMB4SDA", "GPIO29/SMB4SCL", "GPIO30/SMB3SDA", + "GPIO31/SMB3SCL", "GPIO32/nSPI0CS1","SPI0D2", "SPI0D3", "GPIO37/SMB3CSDA", + "GPIO38/SMB3CSCL", "GPIO39/SMB3BSDA", "GPIO40/SMB3BSCL", "GPIO41/BSPRXD", + "GPO42/BSPTXD/STRAP11", "GPIO43/RXD1/JTMS2/BU1RXD", "GPIO44/nCTS1/JTDI2/BU1CTS", + "GPIO45/nDCD1/JTDO2", "GPIO46/nDSR1/JTCK2", "GPIO47/nRI1/JCP_RDY2", + "GPIO48/TXD2/BSPTXD", "GPIO49/RXD2/BSPRXD", "GPIO50/nCTS2", "GPO51/nRTS2/STRAP2", + "GPIO52/nDCD2", "GPO53/nDTR2_BOUT2/STRAP1", "GPIO54/nDSR2", "GPIO55/nRI2", + "GPIO56/R1RXERR", "GPIO57/R1MDC", "GPIO58/R1MDIO", "GPIO59/SMB3DSDA", + "GPIO60/SMB3DSCL", "GPO61/nDTR1_BOUT1/STRAP6", "GPO62/nRTST1/STRAP5", + "GPO63/TXD1/STRAP4", "GPIO64/FANIN0", "GPIO65/FANIN1", "GPIO66/FANIN2", + "GPIO67/FANIN3", "GPIO68/FANIN4", "GPIO69/FANIN5", "GPIO70/FANIN6", "GPIO71/FANIN7", + "GPIO72/FANIN8", "GPIO73/FANIN9", "GPIO74/FANIN10", "GPIO75/FANIN11", + "GPIO76/FANIN12", "GPIO77/FANIN13","GPIO78/FANIN14", "GPIO79/FANIN15", + "GPIO80/PWM0", "GPIO81/PWM1", "GPIO82/PWM2", "GPIO83/PWM3", "GPIO84/R2TXD0", + "GPIO85/R2TXD1", "GPIO86/R2TXEN", "GPIO87/R2RXD0", "GPIO88/R2RXD1", "GPIO89/R2CRSDV", + "GPIO90/R2RXERR", "GPIO91/R2MDC", "GPIO92/R2MDIO", "GPIO93/GA20/SMB5DSCL", + "GPIO94/nKBRST/SMB5DSDA", "GPIO95/nLRESET/nESPIRST", "GPIO96/RG1TXD0", + "GPIO97/RG1TXD1", "GPIO98/RG1TXD2", "GPIO99/RG1TXD3","GPIO100/RG1TXC", + "GPIO101/RG1TXCTL", "GPIO102/RG1RXD0", "GPIO103/RG1RXD1", "GPIO104/RG1RXD2", + "GPIO105/RG1RXD3", "GPIO106/RG1RXC", "GPIO107/RG1RXCTL", "GPIO108/RG1MDC", + "GPIO109/RG1MDIO", "GPIO110/RG2TXD0/DDRV0", "GPIO111/RG2TXD1/DDRV1", + "GPIO112/RG2TXD2/DDRV2", "GPIO113/RG2TXD3/DDRV3", "GPIO114/SMB0SCL", + "GPIO115/SMB0SDA", "GPIO116/SMB1SCL", "GPIO117/SMB1SDA", "GPIO118/SMB2SCL", + "GPIO119/SMB2SDA", "GPIO120/SMB2CSDA", "GPIO121/SMB2CSCL", "GPIO122/SMB2BSDA", + "GPIO123/SMB2BSCL", "GPIO124/SMB1CSDA", "GPIO125/SMB1CSCL","GPIO126/SMB1BSDA", + "GPIO127/SMB1BSCL", "GPIO128/SMB8SCL", "GPIO129/SMB8SDA", "GPIO130/SMB9SCL", + "GPIO131/SMB9SDA", "GPIO132/SMB10SCL", "GPIO133/SMB10SDA","GPIO134/SMB11SCL", + "GPIO135/SMB11SDA", "GPIO136/SD1DT0", "GPIO137/SD1DT1", "GPIO138/SD1DT2", + "GPIO139/SD1DT3", "GPIO140/SD1CLK", "GPIO141/SD1WP", "GPIO142/SD1CMD", + "GPIO143/SD1CD/SD1PWR", "GPIO144/PWM4", "GPIO145/PWM5", "GPIO146/PWM6", + "GPIO147/PWM7", "GPIO148/MMCDT4", "GPIO149/MMCDT5", "GPIO150/MMCDT6", + "GPIO151/MMCDT7", "GPIO152/MMCCLK", "GPIO153/MMCWP", "GPIO154/MMCCMD", + "GPIO155/nMMCCD/nMMCRST", "GPIO156/MMCDT0", "GPIO157/MMCDT1", "GPIO158/MMCDT2", + "GPIO159/MMCDT3", "GPIO160/CLKOUT/RNGOSCOUT", "GPIO161/nLFRAME/nESPICS", + "GPIO162/SERIRQ", "GPIO163/LCLK/ESPICLK", "GPIO164/LAD0/ESPI_IO0", + "GPIO165/LAD1/ESPI_IO1", "GPIO166/LAD2/ESPI_IO2", "GPIO167/LAD3/ESPI_IO3", + "GPIO168/nCLKRUN/nESPIALERT", "GPIO169/nSCIPME", "GPIO170/nSMI", "GPIO171/SMB6SCL", + "GPIO172/SMB6SDA", "GPIO173/SMB7SCL", "GPIO174/SMB7SDA", "GPIO175/PSPI1CK/FANIN19", + "GPIO176/PSPI1DO/FANIN18", "GPIO177/PSPI1DI/FANIN17", "GPIO178/R1TXD0", + "GPIO179/R1TXD1", "GPIO180/R1TXEN", "GPIO181/R1RXD0", "GPIO182/R1RXD1", + "GPIO183/SPI3CK", "GPO184/SPI3D0/STRAP9", "GPO185/SPI3D1/STRAP10", + "GPIO186/nSPI3CS0", "GPIO187/nSPI3CS1", "GPIO188/SPI3D2/nSPI3CS2", + "GPIO189/SPI3D3/nSPI3CS3", "GPIO190/nPRD_SMI", "GPIO191", "GPIO192", "GPIO193/R1CRSDV", + "GPIO194/SMB0BSCL", "GPIO195/SMB0BSDA", "GPIO196/SMB0CSCL", "GPIO197/SMB0DEN", + "GPIO198/SMB0DSDA", "GPIO199/SMB0DSCL", "GPIO200/R2CK", "GPIO201/R1CK", + "GPIO202/SMB0CSDA", "GPIO203/FANIN16", "GPIO204/DDC2SCL", "GPIO205/DDC2SDA", + "GPIO206/HSYNC2", "GPIO207/VSYNC2", "GPIO208/RG2TXC/DVCK", "GPIO209/RG2TXCTL/DDRV4", + "GPIO210/RG2RXD0/DDRV5", "GPIO211/RG2RXD1/DDRV6", "GPIO212/RG2RXD2/DDRV7", + "GPIO213/RG2RXD3/DDRV8", "GPIO214/RG2RXC/DDRV9", "GPIO215/RG2RXCTL/DDRV10", + "GPIO216/RG2MDC/DDRV11", "GPIO217/RG2MDIO/DVHSYNC", "GPIO218/nWDO1", + "GPIO219/nWDO2", "GPIO220/SMB12SCL", "GPIO221/SMB12SDA", "GPIO222/SMB13SCL", + "GPIO223/SMB13SDA", "GPIO224/SPIXCK", "GPO225/SPIXD0/STRAP12", "GPO226/SPIXD1/STRAP13", + "GPIO227/nSPIXCS0", "GPIO228/nSPIXCS1", "GPO229/SPIXD2/STRAP3", "GPIO230/SPIXD3", + "GPIO231/nCLKREQ", "GPI255/DACOSEL" + +Optional Properties: + bias-disable, bias-pull-down, bias-pull-up, input-enable, + input-disable, output-high, output-low, drive-push-pull, + drive-open-drain, input-debounce, slew-rate, drive-strength + + slew-rate valid arguments are: + <0> - slow + <1> - fast + drive-strength valid arguments are: + <2> - 2mA + <4> - 4mA + <8> - 8mA + <12> - 12mA + <16> - 16mA + <24> - 24mA + +For example, pinctrl might have pinmux subnodes like the following: + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + gpio0_iox1ck_pin: gpio0-iox1ck-pin { + pins = "GPIO2/IOX1CK"; + output_high; + }; + +=== Pin Group Subnode === + +Required pin group subnode-properties: +- groups : A string containing the name of the group to mux. +- function: A string containing the name of the function to mux to the + group. + +The following are the list of the available groups and functions : + smb0, smb0b, smb0c, smb0d, smb0den, smb1, smb1b, smb1c, smb1d, + smb2, smb2b, smb2c, smb2d, smb3, smb3b, smb3c, smb3d, smb4, smb4b, + smb4c, smb4d, smb4den, smb5, smb5b, smb5c, smb5d, ga20kbc, smb6, + smb7, smb8, smb9, smb10, smb11, smb12, smb13, smb14, smb15, fanin0, + fanin1, fanin2, fanin3, fanin4, fanin5, fanin6, fanin7, fanin8, + fanin9, fanin10, fanin11 fanin12 fanin13, fanin14, fanin15, faninx, + pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, rg1, rg1mdio, rg2, + rg2mdio, ddr, uart1, uart2, bmcuart0a, bmcuart0b, bmcuart1, iox1, + iox2, ioxh, gspi, mmc, mmcwp, mmccd, mmcrst, mmc8, r1, r1err, r1md, + r2, r2err, r2md, sd1, sd1pwr, wdog1, wdog2, scipme, sci, serirq, + jtag2, spix, spixcs1, pspi1, pspi2, ddc, clkreq, clkout, spi3, spi3cs1, + spi3quad, spi3cs2, spi3cs3, spi0cs1, lpc, lpcclk, espi, lkgpo0, lkgpo1, + lkgpo2, nprd_smi + +For example, pinctrl might have group subnodes like the following: + r1err_pins: r1err-pins { + groups = "r1err"; + function = "r1err"; + }; + r1md_pins: r1md-pins { + groups = "r1md"; + function = "r1md"; + }; + r1_pins: r1-pins { + groups = "r1"; + function = "r1"; + }; + +Examples +======== +pinctrl: pinctrl@f0800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "nuvoton,npcm750-pinctrl"; + ranges = <0 0xf0010000 0x8000>; + + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x80>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + + .... + + gpio7: gpio@f0017000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x7000 0x80>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 224 32>; + }; + + gpio0_iox1d1_pin: gpio0-iox1d1-pin { + pins = "GPIO0/IOX1DI"; + output-high; + }; + + iox1_pins: iox1-pins { + groups = "iox1"; + function = "iox1"; + }; + iox2_pins: iox2-pins { + groups = "iox2"; + function = "iox2"; + }; + + .... + + clkreq_pins: clkreq-pins { + groups = "clkreq"; + function = "clkreq"; + }; +};
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index ffd4345415f3..ab4000eab07d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" if the device is on an spmi bus or an ssbi bus respectively @@ -91,6 +92,7 @@ to specify in a pin configuration subnode: gpio1-gpio26 for pm8998 gpio1-gpio22 for pma8084 gpio1-gpio10 for pmi8994 + gpio1-gpio11 for pms405 - function: Usage: required diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt new file mode 100644 index 000000000000..2b8f77762edc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.txt @@ -0,0 +1,199 @@ +Qualcomm QCS404 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +QCS404 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,qcs404-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, south and east TLMM + tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Defintiion: names for the cells of reg, must contain "north", "south" + and "east". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +- gpio-ranges: + Usage: required + Definition: see ../gpio/gpio.txt + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio119 + Supports mux, bias and drive-strength + + sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, + sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, hdmi_tx, hdmi_ddc, blsp_uart_tx_a2, blsp_spi2, m_voc, + qdss_cti_trig_in_a0, blsp_uart_rx_a2, qdss_tracectl_a, + blsp_uart2, aud_cdc, blsp_i2c_sda_a2, qdss_tracedata_a, + blsp_i2c_scl_a2, qdss_tracectl_b, qdss_cti_trig_in_b0, + blsp_uart1, blsp_spi_mosi_a1, blsp_spi_miso_a1, + qdss_tracedata_b, blsp_i2c1, blsp_spi_cs_n_a1, gcc_plltest, + blsp_spi_clk_a1, rgb_data0, blsp_uart5, blsp_spi5, + adsp_ext, rgb_data1, prng_rosc, rgb_data2, blsp_i2c5, + gcc_gp1_clk_b, rgb_data3, gcc_gp2_clk_b, blsp_spi0, + blsp_uart0, gcc_gp3_clk_b, blsp_i2c0, qdss_traceclk_b, + pcie_clk, nfc_irq, blsp_spi4, nfc_dwl, audio_ts, rgb_data4, + spi_lcd, blsp_uart_tx_b2, gcc_gp3_clk_a, rgb_data5, + blsp_uart_rx_b2, blsp_i2c_sda_b2, blsp_i2c_scl_b2, + pwm_led11, i2s_3_data0_a, ebi2_lcd, i2s_3_data1_a, + i2s_3_data2_a, atest_char, pwm_led3, i2s_3_data3_a, + pwm_led4, i2s_4, ebi2_a, dsd_clk_b, pwm_led5, pwm_led6, + pwm_led7, pwm_led8, pwm_led24, spkr_dac0, blsp_i2c4, + pwm_led9, pwm_led10, spdifrx_opt, pwm_led12, pwm_led13, + pwm_led14, wlan1_adc1, rgb_data_b0, pwm_led15, + blsp_spi_mosi_b1, wlan1_adc0, rgb_data_b1, pwm_led16, + blsp_spi_miso_b1, qdss_cti_trig_out_b0, wlan2_adc1, + rgb_data_b2, pwm_led17, blsp_spi_cs_n_b1, wlan2_adc0, + rgb_data_b3, pwm_led18, blsp_spi_clk_b1, rgb_data_b4, + pwm_led19, ext_mclk1_b, qdss_traceclk_a, rgb_data_b5, + pwm_led20, atest_char3, i2s_3_sck_b, ldo_update, bimc_dte0, + rgb_hsync, pwm_led21, i2s_3_ws_b, dbg_out, rgb_vsync, + i2s_3_data0_b, ldo_en, hdmi_dtest, rgb_de, i2s_3_data1_b, + hdmi_lbk9, rgb_clk, atest_char1, i2s_3_data2_b, ebi_cdc, + hdmi_lbk8, rgb_mdp, atest_char0, i2s_3_data3_b, hdmi_lbk7, + rgb_data_b6, rgb_data_b7, hdmi_lbk6, rgmii_int, cri_trng1, + rgmii_wol, cri_trng0, gcc_tlmm, rgmii_ck, rgmii_tx, + hdmi_lbk5, hdmi_pixel, hdmi_rcv, hdmi_lbk4, rgmii_ctl, + ext_lpass, rgmii_rx, cri_trng, hdmi_lbk3, hdmi_lbk2, + qdss_cti_trig_out_b1, rgmii_mdio, hdmi_lbk1, rgmii_mdc, + hdmi_lbk0, ir_in, wsa_en, rgb_data6, rgb_data7, + atest_char2, ebi_ch0, blsp_uart3, blsp_spi3, sd_write, + blsp_i2c3, gcc_gp1_clk_a, qdss_cti_trig_in_b1, + gcc_gp2_clk_a, ext_mclk0, mclk_in1, i2s_1, dsd_clk_a, + qdss_cti_trig_in_a1, rgmi_dll1, pwm_led22, pwm_led23, + qdss_cti_trig_out_a0, rgmi_dll2, pwm_led1, + qdss_cti_trig_out_a1, pwm_led2, i2s_2, pll_bist, + ext_mclk1_a, mclk_in2, bimc_dte1, i2s_3_sck_a, i2s_3_ws_a + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,qcs404-pinctrl"; + reg = <0x01000000 0x200000>, + <0x01300000 0x200000>, + <0x07b00000 0x200000>; + reg-names = "south", "north", "east"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 120>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt new file mode 100644 index 000000000000..769ca83bb40d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm660-pinctrl.txt @@ -0,0 +1,191 @@ +Qualcomm Technologies, Inc. SDM660 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +SDM660 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,sdm660-pinctrl" or + "qcom,sdm630-pinctrl". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the north, center and south + TLMM tiles. + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: names for the cells of reg, must contain "north", "center" + and "south". + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- gpio-ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies the mapping between gpio controller and + pin-controller pins. + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio113, + Supports mux, bias and drive-strength + sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd, sdc2_data sdc1_rclk, + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, agera_pll, atest_char, atest_char0, atest_char1, + atest_char2, atest_char3, atest_gpsadc0, atest_gpsadc1, + atest_tsens, atest_tsens2, atest_usb1, atest_usb10, + atest_usb11, atest_usb12, atest_usb13, atest_usb2, + atest_usb20, atest_usb21, atest_usb22, atest_usb23, + audio_ref, bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2, + blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, + blsp_i2c8_a, blsp_i2c8_b, blsp_spi1, blsp_spi2, blsp_spi3, + blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8_a, blsp_spi8_b, + blsp_spi8_cs1, blsp_spi8_cs2, blsp_uart1, blsp_uart2, + blsp_uart5, blsp_uart6_a, blsp_uart6_b, blsp_uim1, + blsp_uim2, blsp_uim5, blsp_uim6, cam_mclk, cci_async, + cci_i2c, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, + gcc_gp1, gcc_gp2, gcc_gp3, gpio, gps_tx_a, gps_tx_b, gps_tx_c, + isense_dbg, jitter_bist, ldo_en, ldo_update, m_voc, mdp_vsync, + mdss_vsync0, mdss_vsync1, mdss_vsync2, mdss_vsync3, mss_lte, + nav_pps_a, nav_pps_b, nav_pps_c, pa_indicator, phase_flag0, + phase_flag1, phase_flag10, phase_flag11, phase_flag12, + phase_flag13, phase_flag14, phase_flag15, phase_flag16, + phase_flag17, phase_flag18, phase_flag19, phase_flag2, + phase_flag20, phase_flag21, phase_flag22, phase_flag23, + phase_flag24, phase_flag25, phase_flag26, phase_flag27, + phase_flag28, phase_flag29, phase_flag3, phase_flag30, + phase_flag31, phase_flag4, phase_flag5, phase_flag6, + phase_flag7, phase_flag8, phase_flag9, pll_bypassnl, + pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, pwr_crypto, + pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, qdss_cti1_a, + qdss_cti1_b, qdss_gpio, qdss_gpio0, qdss_gpio1, qdss_gpio10, + qdss_gpio11, qdss_gpio12, qdss_gpio13, qdss_gpio14, qdss_gpio15, + qdss_gpio2, qdss_gpio3, qdss_gpio4, qdss_gpio5, qdss_gpio6, + qdss_gpio7, qdss_gpio8, qdss_gpio9, qlink_enable, qlink_request, + qspi_clk, qspi_cs, qspi_data0, qspi_data1, qspi_data2, + qspi_data3, qspi_resetn, sec_mi2s, sndwire_clk, sndwire_data, + sp_cmu, ssc_irq, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, + uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, + uim2_data, uim2_present, uim2_reset, uim_batt, vfr_1, + vsense_clkout, vsense_data0, vsense_data1, vsense_mode, + wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@3100000 { + compatible = "qcom,sdm660-pinctrl"; + reg = <0x3100000 0x200000>, + <0x3500000 0x200000>, + <0x3900000 0x200000>; + reg-names = "south", "center", "north"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 114>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index abd8fbcf1e62..3902efa18fd0 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -14,8 +14,11 @@ Required Properties: - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller. + - "renesas,pfc-r8a7744": for R8A7744 (RZ/G1N) compatible pin-controller. - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller. - "renesas,pfc-r8a77470": for R8A77470 (RZ/G1C) compatible pin-controller. + - "renesas,pfc-r8a774a1": for R8A774A1 (RZ/G2M) compatible pin-controller. + - "renesas,pfc-r8a774c0": for R8A774C0 (RZ/G2E) compatible pin-controller. - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt new file mode 100644 index 000000000000..25e53acd523e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.txt @@ -0,0 +1,153 @@ +Renesas RZ/N1 SoC Pinctrl node description. + +Pin controller node +------------------- +Required properties: +- compatible: SoC-specific compatible string "renesas,<soc-specific>-pinctrl" + followed by "renesas,rzn1-pinctrl" as fallback. The SoC-specific compatible + strings must be one of: + "renesas,r9a06g032-pinctrl" for RZ/N1D + "renesas,r9a06g033-pinctrl" for RZ/N1S +- reg: Address base and length of the memory area where the pin controller + hardware is mapped to. +- clocks: phandle for the clock, see the description of clock-names below. +- clock-names: Contains the name of the clock: + "bus", the bus clock, sometimes described as pclk, for register accesses. + +Example: + pinctrl: pin-controller@40067000 { + compatible = "renesas,r9a06g032-pinctrl", "renesas,rzn1-pinctrl"; + reg = <0x40067000 0x1000>, <0x51000000 0x480>; + clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>; + clock-names = "bus"; + }; + +Sub-nodes +--------- + +The child nodes of the pin controller node describe a pin multiplexing +function. + +- Pin multiplexing sub-nodes: + A pin multiplexing sub-node describes how to configure a set of + (or a single) pin in some desired alternate function mode. + A single sub-node may define several pin configurations. + Please refer to pinctrl-bindings.txt to get to know more on generic + pin properties usage. + + The allowed generic formats for a pin multiplexing sub-node are the + following ones: + + node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + node-2 { + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + sub-node-2 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + node-3 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + + sub-node-1 { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + + ... + + sub-node-n { + pinmux = <PIN_ID_AND_MUX>, <PIN_ID_AND_MUX>, ... ; + GENERIC_PINCONFIG; + }; + }; + + Use the latter two formats when pins part of the same logical group need to + have different generic pin configuration flags applied. Note that the generic + pinconfig in node-3 does not apply to the sub-nodes. + + Client sub-nodes shall refer to pin multiplexing sub-nodes using the phandle + of the most external one. + + Eg. + + client-1 { + ... + pinctrl-0 = <&node-1>; + ... + }; + + client-2 { + ... + pinctrl-0 = <&node-2>; + ... + }; + + Required properties: + - pinmux: + integer array representing pin number and pin multiplexing configuration. + When a pin has to be configured in alternate function mode, use this + property to identify the pin by its global index, and provide its + alternate function configuration number along with it. + When multiple pins are required to be configured as part of the same + alternate function they shall be specified as members of the same + argument list of a single "pinmux" property. + Integers values in the "pinmux" argument list are assembled as: + (PIN | MUX_FUNC << 8) + where PIN directly corresponds to the pl_gpio pin number and MUX_FUNC is + one of the alternate function identifiers defined in: + <include/dt-bindings/pinctrl/rzn1-pinctrl.h> + These identifiers collapse the IO Multiplex Configuration Level 1 and + Level 2 numbers that are detailed in the hardware reference manual into a + single number. The identifiers for Level 2 are simply offset by 10. + Additional identifiers are provided to specify the MDIO source peripheral. + + Optional generic pinconf properties: + - bias-disable - disable any pin bias + - bias-pull-up - pull up the pin with 50 KOhm + - bias-pull-down - pull down the pin with 50 KOhm + - bias-high-impedance - high impedance mode + - drive-strength - sink or source at most 4, 6, 8 or 12 mA + + Example: + A serial communication interface with a TX output pin and an RX input pin. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = < + RZN1_PINMUX(103, RZN1_FUNC_UART0_I) /* UART0_TXD */ + RZN1_PINMUX(104, RZN1_FUNC_UART0_I) /* UART0_RXD */ + >; + }; + }; + + Example 2: + Here we set the pull up on the RXD pin of the UART. + + &pinctrl { + pins_uart0: pins_uart0 { + pinmux = <RZN1_PINMUX(103, RZN1_FUNC_UART0_I)>; /* TXD */ + + pins_uart6_rx { + pinmux = <RZN1_PINMUX(104, RZN1_FUNC_UART0_I)>; /* RXD */ + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/actions,owl-sps.txt b/Documentation/devicetree/bindings/power/actions,owl-sps.txt index 78edd63641e8..a3571937b019 100644 --- a/Documentation/devicetree/bindings/power/actions,owl-sps.txt +++ b/Documentation/devicetree/bindings/power/actions,owl-sps.txt @@ -3,11 +3,13 @@ Actions Semi Owl Smart Power System (SPS) Required properties: - compatible : "actions,s500-sps" for S500 "actions,s700-sps" for S700 + "actions,s900-sps" for S900 - reg : Offset and length of the register set for the device. - #power-domain-cells : Must be 1. See macros in: include/dt-bindings/power/owl-s500-powergate.h for S500 include/dt-bindings/power/owl-s700-powergate.h for S700 + include/dt-bindings/power/owl-s900-powergate.h for S900 Example: diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt index f747f95eee58..5f24586c8cf3 100644 --- a/Documentation/devicetree/bindings/power/renesas,apmu.txt +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -8,7 +8,9 @@ Required properties: - compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. Examples with soctypes are: - "renesas,r8a7743-apmu" (RZ/G1M) + - "renesas,r8a7744-apmu" (RZ/G1N) - "renesas,r8a7745-apmu" (RZ/G1E) + - "renesas,r8a77470-apmu" (RZ/G1C) - "renesas,r8a7790-apmu" (R-Car H2) - "renesas,r8a7791-apmu" (R-Car M2-W) - "renesas,r8a7792-apmu" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 180ae65be753..eae2a880155a 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -8,8 +8,11 @@ and various coprocessors. Required properties: - compatible: Must contain exactly one of the following: - "renesas,r8a7743-sysc" (RZ/G1M) + - "renesas,r8a7744-sysc" (RZ/G1N) - "renesas,r8a7745-sysc" (RZ/G1E) - "renesas,r8a77470-sysc" (RZ/G1C) + - "renesas,r8a774a1-sysc" (RZ/G2M) + - "renesas,r8a774c0-sysc" (RZ/G2E) - "renesas,r8a7779-sysc" (R-Car H1) - "renesas,r8a7790-sysc" (R-Car H2) - "renesas,r8a7791-sysc" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt index 651491bb63b7..5705f575862d 100644 --- a/Documentation/devicetree/bindings/power/reset/qcom,pon.txt +++ b/Documentation/devicetree/bindings/power/reset/qcom,pon.txt @@ -6,7 +6,10 @@ and resin along with the Android reboot-mode. This DT node has pwrkey and resin as sub nodes. Required Properties: --compatible: "qcom,pm8916-pon" +-compatible: Must be one of: + "qcom,pm8916-pon" + "qcom,pms405-pon" + -reg: Specifies the physical address of the pon register Optional subnode: diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt index c9dd17d142ad..dc0568933359 100644 --- a/Documentation/devicetree/bindings/power/supply/bq25890.txt +++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt @@ -1,5 +1,8 @@ Binding for TI bq25890 Li-Ion Charger +This driver will support the bq25896 and the bq25890. There are other ICs +in the same family but those have not been tested. + Required properties: - compatible: Should contain one of the following: * "ti,bq25890" diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index 37994fdb18ca..4fa8e08df2b6 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -23,6 +23,7 @@ Required properties: * "ti,bq27546" - BQ27546 * "ti,bq27742" - BQ27742 * "ti,bq27545" - BQ27545 + * "ti,bq27411" - BQ27411 * "ti,bq27421" - BQ27421 * "ti,bq27425" - BQ27425 * "ti,bq27426" - BQ27426 diff --git a/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt new file mode 100644 index 000000000000..5266fab16575 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/sc2731_charger.txt @@ -0,0 +1,40 @@ +Spreadtrum SC2731 PMIC battery charger binding + +Required properties: + - compatible: Should be "sprd,sc2731-charger". + - reg: Address offset of charger register. + - phys: Contains a phandle to the USB phy. + +Optional Properties: +- monitored-battery: phandle of battery characteristics devicetree node. + The charger uses the following battery properties: +- charge-term-current-microamp: current for charge termination phase. +- constant-charge-voltage-max-microvolt: maximum constant input voltage. + See Documentation/devicetree/bindings/power/supply/battery.txt + +Example: + + bat: battery { + compatible = "simple-battery"; + charge-term-current-microamp = <120000>; + constant-charge-voltage-max-microvolt = <4350000>; + ...... + }; + + sc2731_pmic: pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + + charger@0 { + compatible = "sprd,sc2731-charger"; + reg = <0x0>; + phys = <&ssphy>; + monitored-battery = <&bat>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index c7610718adff..f9be1acf891c 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -12,6 +12,11 @@ Optional properties: disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". +- fsl,pmic-stby-poweroff: if present, configure the PMIC to shutdown all + power rails when PMIC_STBY_REQ line is asserted during the power off sequence. + Use this option if the SoC should be powered off by external power + management IC (PMIC) on PMIC_STBY_REQ signal. + As opposite to PMIC_STBY_REQ boards can implement PMIC_ON_REQ signal. Required child node: - regulators: This is the list of child nodes that specify the regulator diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index 58a1d97972f5..45025b5b67f6 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible: "qcom,rpm-pm8998-regulators" "qcom,rpm-pma8084-regulators" "qcom,rpm-pmi8998-regulators" + "qcom,rpm-pms405-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -188,6 +189,24 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l7-supply: +- vdd_l3_l8-supply: +- vdd_l9-supply: +- vdd_l10_l11_l12_l13-supply: + Usage: optional (pms405 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -222,6 +241,10 @@ pma8084: pmi8998: bob +pms405: + s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, + l13 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 76ead07072b1..4b98ca26e61a 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -1,7 +1,9 @@ -ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings +ROHM BD71837 and BD71847 Power Management Integrated Circuit regulator bindings Required properties: - - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" + - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for + BD71837. For BD71847 names should be "buck1", ..., "buck6" + and "ldo1", ..., "ldo6" List of regulators provided by this controller. BD71837 regulators node should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at @@ -16,10 +18,14 @@ disabled by driver at startup. LDO5 and LDO6 are supplied by those and if they are disabled at startup the voltage monitoring for LDO5/LDO6 will cause PMIC to reset. -The valid names for regulator nodes are: +The valid names for BD71837 regulator nodes are: BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7 +The valid names for BD71847 regulator nodes are: +BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + Optional properties: - Any optional property defined in bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt new file mode 100644 index 000000000000..a3f476240565 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -0,0 +1,68 @@ +STMicroelectronics STPMIC1 Voltage regulators + +Regulator Nodes are optional depending on needs. + +Available Regulators in STPMIC1 device are: + - buck1 for Buck BUCK1 + - buck2 for Buck BUCK2 + - buck3 for Buck BUCK3 + - buck4 for Buck BUCK4 + - ldo1 for LDO LDO1 + - ldo2 for LDO LDO2 + - ldo3 for LDO LDO3 + - ldo4 for LDO LDO4 + - ldo5 for LDO LDO5 + - ldo6 for LDO LDO6 + - vref_ddr for LDO Vref DDR + - boost for Buck BOOST + - pwr_sw1 for VBUS_OTG switch + - pwr_sw2 for SW_OUT switch + +Switches are fixed voltage regulators with only enable/disable capability. + +Optional properties: +- st,mask-reset: mask reset for this regulator: the regulator configuration + is maintained during pmic reset. +- regulator-pull-down: enable high pull down + if not specified light pull down is used +- regulator-over-current-protection: + if set, all regulators are switched off in case of over-current detection + on this regulator, + if not set, the driver only sends an over-current event. +- interrupt-parent: phandle to the parent interrupt controller +- interrupts: index of current limit detection interrupt +- <regulator>-supply: phandle to the parent supply/regulator node + each regulator supply can be described except vref_ddr. + +Example: +regulators { + compatible = "st,stpmic1-regulators"; + + ldo6-supply = <&v3v3>; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + interrupts = <IT_CURLIM_BUCK1 0>; + interrupt-parent = <&pmic>; + st,mask-reset; + regulator-pull-down; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + interrupts = <IT_CURLIM_BUCK4 0>; + interrupt-parent = <&mypmic>; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-over-current-protection; + }; +}; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt new file mode 100644 index 000000000000..a842a782b557 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt @@ -0,0 +1,126 @@ +Qualcomm Technology Inc. ADSP Peripheral Image Loader + +This document defines the binding for a component that loads and boots firmware +on the Qualcomm Technology Inc. ADSP Hexagon core. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,sdm845-adsp-pil" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the qdsp6ss register + +- interrupts-extended: + Usage: required + Value type: <prop-encoded-array> + Definition: must list the watchdog, fatal IRQs ready, handover and + stop-ack IRQs + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: List of 8 phandle and clock specifier pairs for the adsp. + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: List of clock input name strings sorted in the same + order as the clocks property. Definition must have + "xo", "sway_cbcr", "lpass_aon", "lpass_ahbs_aon_cbcr", + "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", "qdsp6ss_sleep" + and "qdsp6ss_core". + +- power-domains: + Usage: required + Value type: <phandle> + Definition: reference to cx power domain node. + +- resets: + Usage: required + Value type: <phandle> + Definition: reference to the list of 2 reset-controller for the adsp. + +- reset-names: + Usage: required + Value type: <stringlist> + Definition: must be "pdc_sync" and "cc_lpass" + +- qcom,halt-regs: + Usage: required + Value type: <prop-encoded-array> + Definition: a phandle reference to a syscon representing TCSR followed + by the offset within syscon for lpass halt register. + +- memory-region: + Usage: required + Value type: <phandle> + Definition: reference to the reserved-memory for the ADSP + +- qcom,smem-states: + Usage: required + Value type: <phandle> + Definition: reference to the smem state for requesting the ADSP to + shut down + +- qcom,smem-state-names: + Usage: required + Value type: <stringlist> + Definition: must be "stop" + + += SUBNODES +The adsp node may have an subnode named "glink-edge" that describes the +communication edge, channels and devices related to the ADSP. +See ../soc/qcom/qcom,glink.txt for details on how to describe these. + += EXAMPLE +The following example describes the resources needed to boot control the +ADSP, as it is found on SDM845 boards. + + remoteproc@17300000 { + compatible = "qcom,sdm845-adsp-pil"; + reg = <0x17300000 0x40c>; + + interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_LPASS_SWAY_CLK>, + <&lpasscc LPASS_AUDIO_WRAPPER_AON_CLK>, + <&lpasscc LPASS_Q6SS_AHBS_AON_CLK>, + <&lpasscc LPASS_Q6SS_AHBM_AON_CLK>, + <&lpasscc LPASS_QDSP6SS_XO_CLK>, + <&lpasscc LPASS_QDSP6SS_SLEEP_CLK>, + <&lpasscc LPASS_QDSP6SS_CORE_CLK>; + clock-names = "xo", "sway_cbcr", "lpass_aon", + "lpass_ahbs_aon_cbcr", + "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", + "qdsp6ss_sleep", "qdsp6ss_core"; + + power-domains = <&rpmhpd SDM845_CX>; + + resets = <&pdc_reset PDC_AUDIO_SYNC_RESET>, + <&aoss_reset AOSS_CC_LPASS_RESTART>; + reset-names = "pdc_sync", "cc_lpass"; + + qcom,halt-regs = <&tcsr_mutex_regs 0x22000>; + + memory-region = <&pil_adsp_mem>; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + }; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt index 728e4193f7a6..9c0cff3a5ed8 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -10,6 +10,11 @@ on the Qualcomm ADSP Hexagon core. "qcom,msm8974-adsp-pil" "qcom,msm8996-adsp-pil" "qcom,msm8996-slpi-pil" + "qcom,qcs404-adsp-pas" + "qcom,qcs404-cdsp-pas" + "qcom,qcs404-wcss-pas" + "qcom,sdm845-adsp-pas" + "qcom,sdm845-cdsp-pas" - interrupts-extended: Usage: required diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 601dd9f389aa..9ff5b0309417 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -53,13 +53,17 @@ on the Qualcomm Hexagon core. Definition: reference to the reset-controller for the modem sub-system reference to the list of 3 reset-controllers for the wcss sub-system + reference to the list of 2 reset-controllers for the modem + sub-system on SDM845 SoCs - reset-names: Usage: required Value type: <stringlist> Definition: must be "mss_restart" for the modem sub-system - Definition: must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset" - for the wcss syb-system + must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset" + for the wcss sub-system + must be "mss_restart", "pdc_reset" for the modem + sub-system on SDM845 SoCs - cx-supply: - mss-supply: diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt index 5e1afc3d8480..1ab1d109318e 100644 --- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt +++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt @@ -5,7 +5,7 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. Required properties: -- compatible: Should be "fsl,imx7-src", "syscon" +- compatible: Should be "fsl,imx7d-src", "syscon" - reg: should be register base and length as documented in the datasheet - interrupts: Should contain SRC interrupt diff --git a/Documentation/devicetree/bindings/reset/qcom,pdc-global.txt b/Documentation/devicetree/bindings/reset/qcom,pdc-global.txt new file mode 100644 index 000000000000..a62a492843e7 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/qcom,pdc-global.txt @@ -0,0 +1,52 @@ +PDC Global +====================================== + +This binding describes a reset-controller found on PDC-Global (Power Domain +Controller) block for Qualcomm Technologies Inc SDM845 SoCs. + +Required properties: +- compatible: + Usage: required + Value type: <string> + Definition: must be: + "qcom,sdm845-pdc-global" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the register + space. + +- #reset-cells: + Usage: required + Value type: <uint> + Definition: must be 1; cell entry represents the reset index. + +Example: + +pdc_reset: reset-controller@b2e0000 { + compatible = "qcom,sdm845-pdc-global"; + reg = <0xb2e0000 0x20000>; + #reset-cells = <1>; +}; + +PDC reset clients +====================================== + +Device nodes that need access to reset lines should +specify them as a reset phandle in their corresponding node as +specified in reset.txt. + +For a list of all valid reset indices see +<dt-bindings/reset/qcom,sdm845-pdc.h> + +Example: + +modem-pil@4080000 { + ... + + resets = <&pdc_reset PDC_MODEM_SYNC_RESET>; + reset-names = "pdc_reset"; + + ... +}; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index 67e83b02e10b..b03c48a1150e 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -16,8 +16,11 @@ Required properties: - "renesas,<soctype>-rst" for R-Car Gen2 and Gen3, and RZ/G Examples with soctypes are: - "renesas,r8a7743-rst" (RZ/G1M) + - "renesas,r8a7744-rst" (RZ/G1N) - "renesas,r8a7745-rst" (RZ/G1E) - "renesas,r8a77470-rst" (RZ/G1C) + - "renesas,r8a774a1-rst" (RZ/G2M) + - "renesas,r8a774c0-rst" (RZ/G2E) - "renesas,r8a7778-reset-wdt" (R-Car M1A) - "renesas,r8a7779-reset-wdt" (R-Car H1) - "renesas,r8a7790-rst" (R-Car H2) diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index eaca9da79d83..e52e16c6bc57 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -14,6 +14,10 @@ Required properties: - "renesas,scifa-r8a7743" for R8A7743 (RZ/G1M) SCIFA compatible UART. - "renesas,scifb-r8a7743" for R8A7743 (RZ/G1M) SCIFB compatible UART. - "renesas,hscif-r8a7743" for R8A7743 (RZ/G1M) HSCIF compatible UART. + - "renesas,scif-r8a7744" for R8A7744 (RZ/G1N) SCIF compatible UART. + - "renesas,scifa-r8a7744" for R8A7744 (RZ/G1N) SCIFA compatible UART. + - "renesas,scifb-r8a7744" for R8A7744 (RZ/G1N) SCIFB compatible UART. + - "renesas,hscif-r8a7744" for R8A7744 (RZ/G1N) HSCIF compatible UART. - "renesas,scif-r8a7745" for R8A7745 (RZ/G1E) SCIF compatible UART. - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. @@ -50,6 +54,8 @@ Required properties: - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART. - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART. - "renesas,hscif-r8a77980" for R8A77980 (R-Car V3H) HSCIF compatible UART. + - "renesas,scif-r8a77990" for R8A77990 (R-Car E3) SCIF compatible UART. + - "renesas,hscif-r8a77990" for R8A77990 (R-Car E3) HSCIF compatible UART. - "renesas,scif-r8a77995" for R8A77995 (R-Car D3) SCIF compatible UART. - "renesas,hscif-r8a77995" for R8A77995 (R-Car D3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. diff --git a/Documentation/devicetree/bindings/serial/uniphier-uart.txt b/Documentation/devicetree/bindings/serial/uniphier-uart.txt index 0b3892a7a528..7a1bf02bb869 100644 --- a/Documentation/devicetree/bindings/serial/uniphier-uart.txt +++ b/Documentation/devicetree/bindings/serial/uniphier-uart.txt @@ -7,7 +7,7 @@ Required properties: - clocks: phandle to the input clock. Optional properties: -- fifo-size: the RX/TX FIFO size. Defaults to 64 if not specified. +-auto-flow-control: enable automatic flow control support. Example: aliases { @@ -19,5 +19,4 @@ Example: reg = <0x54006800 0x40>; interrupts = <0 33 4>; clocks = <&uart_clk>; - fifo-size = <64>; }; diff --git a/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt new file mode 100644 index 000000000000..436d2106e80d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/amlogic/amlogic,canvas.txt @@ -0,0 +1,29 @@ +Amlogic Canvas +================================ + +A canvas is a collection of metadata that describes a pixel buffer. +Those metadata include: width, height, phyaddr, wrapping, block mode +and endianness. + +Many IPs within Amlogic SoCs rely on canvas indexes to read/write pixel data +rather than use the phy addresses directly. For instance, this is the case for +the video decoders and the display. + +Amlogic SoCs have 256 canvas. + +Device Tree Bindings: +--------------------- + +Video Lookup Table +-------------------------- + +Required properties: +- compatible: "amlogic,canvas" +- reg: Base physical address and size of the canvas registers. + +Example: + +canvas: video-lut@48 { + compatible = "amlogic,canvas"; + reg = <0x0 0x48 0x0 0x14>; +}; diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt index 03c741602c6d..6d2dd8a31482 100644 --- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/network.txt @@ -98,6 +98,12 @@ The property below is dependent on fsl,tdm-interface: usage: optional for tdm interface value type: <empty> Definition : Internal loopback connecting on TDM layer. +- fsl,hmask + usage: optional + Value type: <u16> + Definition: HDLC address recognition. Set to zero to disable + address filtering of packets: + fsl,hmask = /bits/ 16 <0x0000>; Example for tdm interface: diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt index f9987c30f0d5..5a2ef1726e2a 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -19,10 +19,12 @@ IP Pairing Required properties in pwrap device node. - compatible: "mediatek,mt2701-pwrap" for MT2701/7623 SoCs + "mediatek,mt6765-pwrap" for MT6765 SoCs "mediatek,mt6797-pwrap" for MT6797 SoCs "mediatek,mt7622-pwrap" for MT7622 SoCs "mediatek,mt8135-pwrap" for MT8135 SoCs "mediatek,mt8173-pwrap" for MT8173 SoCs + "mediatek,mt8183-pwrap" for MT8183 SoCs - interrupts: IRQ for pwrap in SOC - reg-names: Must include the following entries: "pwrap": Main registers base diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt index ff92e5a41bed..dab7ca9f250c 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt @@ -53,20 +53,8 @@ Required properties: - clocks: Serial engine core clock needed by the device. Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller - -Required properties: -- compatible: Must contain "qcom,geni-spi". -- reg: Must contain SPI register location and length. -- interrupts: Must contain SPI controller interrupts. -- clock-names: Must contain "se". -- clocks: Serial engine core clock needed by the device. -- spi-max-frequency: Specifies maximum SPI clock frequency, units - Hz. -- #address-cells: Must be <1> to define a chip select address on - the SPI bus. -- #size-cells: Must be <0>. - -SPI slave nodes must be children of the SPI master node and conform to SPI bus -binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. +node binding is described in +Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt. Example: geniqup@8c0000 { @@ -103,17 +91,4 @@ Example: pinctrl-1 = <&qup_1_uart_3_sleep>; }; - spi0: spi@a84000 { - compatible = "qcom,geni-spi"; - reg = <0xa84000 0x4000>; - interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "se"; - clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qup_1_spi_2_active>; - pinctrl-1 = <&qup_1_spi_2_sleep>; - spi-max-frequency = <19200000>; - #address-cells = <1>; - #size-cells = <0>; - }; } diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt index 7dc5ce858a0e..46e27cd69f18 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -13,6 +13,7 @@ On RK3328 SoCs, the GRF adds a section for USB2PHYGRF, Required Properties: - compatible: GRF should be one of the following: + - "rockchip,px30-grf", "syscon": for px30 - "rockchip,rk3036-grf", "syscon": for rk3036 - "rockchip,rk3066-grf", "syscon": for rk3066 - "rockchip,rk3188-grf", "syscon": for rk3188 @@ -23,6 +24,7 @@ Required Properties: - "rockchip,rk3399-grf", "syscon": for rk3399 - "rockchip,rv1108-grf", "syscon": for rv1108 - compatible: PMUGRF should be one of the following: + - "rockchip,px30-pmugrf", "syscon": for px30 - "rockchip,rk3368-pmugrf", "syscon": for rk3368 - "rockchip,rk3399-pmugrf", "syscon": for rk3399 - compatible: SGRF should be one of the following diff --git a/Documentation/devicetree/bindings/sound/adi,adau1977.txt b/Documentation/devicetree/bindings/sound/adi,adau1977.txt new file mode 100644 index 000000000000..e79aeef73f28 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1977.txt @@ -0,0 +1,54 @@ +Analog Devices ADAU1977/ADAU1978/ADAU1979 + +Datasheets: +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1977.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1978.pdf +http://www.analog.com/media/en/technical-documentation/data-sheets/ADAU1979.pdf + +This driver supports both the I2C and SPI bus. + +Required properties: + - compatible: Should contain one of the following: + "adi,adau1977" + "adi,adau1978" + "adi,adau1979" + + - AVDD-supply: analog power supply for the device, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + - reset-gpio: the reset pin for the chip, for more details consult + Documentation/devicetree/bindings/gpio/gpio.txt + + - DVDD-supply: supply voltage for the digital core, please consult + Documentation/devicetree/bindings/regulator/regulator.txt + +For required properties on SPI, please consult +Documentation/devicetree/bindings/spi/spi-bus.txt + +Required properties on I2C: + + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Examples: + + adau1977_spi: adau1977@0 { + compatible = "adi,adau1977"; + spi-max-frequency = <600000>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + adau1977_i2c: adau1977@11 { + compatible = "adi,adau1977"; + reg = <0x11>; + + AVDD-supply = <®ulator>; + DVDD-supply = <®ulator_digital>; + + reset_gpio = <&gpio 10 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt new file mode 100644 index 000000000000..5672d0bc5b16 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt @@ -0,0 +1,24 @@ +* Amlogic Audio PDM input + +Required properties: +- compatible: 'amlogic,axg-pdm' +- reg: physical base address of the controller and length of memory + mapped region. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "dclk" : pdm digital clock + * "sysclk" : dsp system clock +- #sound-dai-cells: must be 0. + +Example of PDM on the A113 SoC: + +pdm: audio-controller@ff632000 { + compatible = "amlogic,axg-pdm"; + reg = <0x0 0xff632000 0x0 0x34>; + #sound-dai-cells = <0>; + clocks = <&clkc_audio AUD_CLKID_PDM>, + <&clkc_audio AUD_CLKID_PDM_DCLK>, + <&clkc_audio AUD_CLKID_PDM_SYSCLK>; + clock-names = "pclk", "dclk", "sysclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l51.txt b/Documentation/devicetree/bindings/sound/cs42l51.txt new file mode 100644 index 000000000000..4b5de33ce377 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs42l51.txt @@ -0,0 +1,17 @@ +CS42L51 audio CODEC + +Optional properties: + + - clocks : a list of phandles + clock-specifiers, one for each entry in + clock-names + + - clock-names : must contain "MCLK" + +Example: + +cs42l51: cs42l51@4a { + compatible = "cirrus,cs42l51"; + reg = <0x4a>; + clocks = <&mclk_prov>; + clock-names = "MCLK"; +}; diff --git a/Documentation/devicetree/bindings/sound/maxim,max98088.txt b/Documentation/devicetree/bindings/sound/maxim,max98088.txt new file mode 100644 index 000000000000..da764d913319 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/maxim,max98088.txt @@ -0,0 +1,23 @@ +MAX98088 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible: "maxim,max98088" or "maxim,max98089". +- reg: The I2C address of the device. + +Optional properties: + +- clocks: the clock provider of MCLK, see ../clock/clock-bindings.txt section + "consumer" for more information. +- clock-names: must be set to "mclk" + +Example: + +max98089: codec@10 { + compatible = "maxim,max98089"; + reg = <0x10>; + clocks = <&clks IMX6QDL_CLK_CKO2>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt new file mode 100644 index 000000000000..912f8fae11c5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt @@ -0,0 +1,23 @@ +Mikroe-PROTO audio board + +Required properties: + - compatible: "mikroe,mikroe-proto" + - dai-format: Must be "i2s". + - i2s-controller: The phandle of the I2S controller. + - audio-codec: The phandle of the WM8731 audio codec. +Optional properties: + - model: The user-visible name of this sound complex. + - bitclock-master: Indicates dai-link bit clock master; for details see simple-card.txt (1). + - frame-master: Indicates dai-link frame master; for details see simple-card.txt (1). + +(1) : There must be the same master for both bit and frame clocks. + +Example: + sound { + compatible = "mikroe,mikroe-proto"; + model = "wm8731 @ sama5d2_xplained"; + i2s-controller = <&i2s0>; + audio-codec = <&wm8731>; + dai-format = "i2s"; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/nau8822.txt b/Documentation/devicetree/bindings/sound/nau8822.txt new file mode 100644 index 000000000000..a471d162d4e5 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8822.txt @@ -0,0 +1,16 @@ +NAU8822 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "nuvoton,nau8822" + + - reg : the I2C address of the device. + +Example: + +codec: nau8822@1a { + compatible = "nuvoton,nau8822"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/pcm3060.txt b/Documentation/devicetree/bindings/sound/pcm3060.txt new file mode 100644 index 000000000000..90fcb8523099 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm3060.txt @@ -0,0 +1,17 @@ +PCM3060 audio CODEC + +This driver supports both I2C and SPI. + +Required properties: + +- compatible: "ti,pcm3060" + +- reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Examples: + + pcm3060: pcm3060@46 { + compatible = "ti,pcm3060"; + reg = <0x46>; + }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt index a8179409c194..d74888b9f1bb 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -49,7 +49,7 @@ configuration of each dai. Must contain the following properties. Usage: required for mi2s interface Value type: <prop-encoded-array> Definition: Must be list of serial data lines used by this dai. - should be one or more of the 1-4 sd lines. + should be one or more of the 0-3 sd lines. - qcom,tdm-sync-mode: Usage: required for tdm interface @@ -137,42 +137,42 @@ q6afe@4 { prim-mi2s-rx@16 { reg = <16>; - qcom,sd-lines = <1 3>; + qcom,sd-lines = <0 2>; }; prim-mi2s-tx@17 { reg = <17>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; sec-mi2s-rx@18 { reg = <18>; - qcom,sd-lines = <1 4>; + qcom,sd-lines = <0 3>; }; sec-mi2s-tx@19 { reg = <19>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; tert-mi2s-rx@20 { reg = <20>; - qcom,sd-lines = <2 4>; + qcom,sd-lines = <1 3>; }; tert-mi2s-tx@21 { reg = <21>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-rx@22 { reg = <22>; - qcom,sd-lines = <1>; + qcom,sd-lines = <0>; }; quat-mi2s-tx@23 { reg = <23>; - qcom,sd-lines = <2>; + qcom,sd-lines = <1>; }; }; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 9e764270c36b..d92b705e7917 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -340,10 +340,12 @@ Required properties: - compatible : "renesas,rcar_sound-<soctype>", fallbacks "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) - "renesas,rcar_sound-gen3" if generation3 + "renesas,rcar_sound-gen3" if generation3 (or RZ/G2) Examples with soctypes are: - "renesas,rcar_sound-r8a7743" (RZ/G1M) + - "renesas,rcar_sound-r8a7744" (RZ/G1N) - "renesas,rcar_sound-r8a7745" (RZ/G1E) + - "renesas,rcar_sound-r8a774a1" (RZ/G2M) - "renesas,rcar_sound-r8a7778" (R-Car M1A) - "renesas,rcar_sound-r8a7779" (R-Car H1) - "renesas,rcar_sound-r8a7790" (R-Car H2) @@ -353,6 +355,7 @@ Required properties: - "renesas,rcar_sound-r8a7795" (R-Car H3) - "renesas,rcar_sound-r8a7796" (R-Car M3-W) - "renesas,rcar_sound-r8a77965" (R-Car M3-N) + - "renesas,rcar_sound-r8a77990" (R-Car E3) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 diff --git a/Documentation/devicetree/bindings/sound/st,sta32x.txt b/Documentation/devicetree/bindings/sound/st,sta32x.txt index 255de3ae5b2f..52265fb757c5 100644 --- a/Documentation/devicetree/bindings/sound/st,sta32x.txt +++ b/Documentation/devicetree/bindings/sound/st,sta32x.txt @@ -19,6 +19,10 @@ Required properties: Optional properties: + - clocks, clock-names: Clock specifier for XTI input clock. + If specified, the clock will be enabled when the codec is probed, + and disabled when it is removed. The 'clock-names' must be set to 'xti'. + - st,output-conf: number, Selects the output configuration: 0: 2-channel (full-bridge) power, 2-channel data-out 1: 2 (half-bridge). 1 (full-bridge) on-board power @@ -39,6 +43,9 @@ Optional properties: - st,thermal-warning-recover: If present, thermal warning recovery is enabled. + - st,fault-detect-recovery: + If present, fault detect recovery is enabled. + - st,thermal-warning-adjustment: If present, thermal warning adjustment is enabled. @@ -76,6 +83,8 @@ Example: codec: sta32x@38 { compatible = "st,sta32x"; reg = <0x1c>; + clocks = <&clock>; + clock-names = "xti"; reset-gpios = <&gpio1 19 0>; power-down-gpios = <&gpio1 16 0>; st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt index 3a3fc506e43a..3f4467ff0aa2 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt @@ -31,7 +31,11 @@ SAI subnodes required properties: - reg: Base address and size of SAI sub-block register set. - clocks: Must contain one phandle and clock specifier pair for sai_ck which feeds the internal clock generator. + If the SAI shares a master clock, with another SAI set as MCLK + clock provider, SAI provider phandle must be specified here. - clock-names: Must contain "sai_ck". + Must also contain "MCLK", if SAI shares a master clock, + with a SAI set as MCLK clock provider. - dmas: see Documentation/devicetree/bindings/dma/stm32-dma.txt - dma-names: identifier string for each DMA request line "tx": if sai sub-block is configured as playback DAI @@ -51,6 +55,9 @@ SAI subnodes Optional properties: configured according to protocol defined in related DAI link node, such as i2s, left justified, right justified, dsp and pdm protocols. Note: ac97 protocol is not supported by SAI driver + - #clock-cells: should be 0. This property must be present if the SAI device + is a master clock provider, according to clocks bindings, described in + Documentation/devicetree/bindings/clock/clock-bindings.txt. The device node should contain one 'port' child node with one child 'endpoint' node, according to the bindings defined in Documentation/devicetree/bindings/ diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index b9d50d6cdef3..61e71c1729e0 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -10,6 +10,7 @@ Required properties: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - reg: physical base address of the controller and length of memory mapped region. - interrupts: should contain the I2S interrupt. @@ -26,6 +27,7 @@ Required properties for the following compatibles: - "allwinner,sun6i-a31-i2s" - "allwinner,sun8i-a83t-i2s" - "allwinner,sun8i-h3-i2s" + - "allwinner,sun50i-a64-codec-i2s" - resets: phandle to the reset line for this codec Example: diff --git a/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt new file mode 100644 index 000000000000..4f8ad0e04d20 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sun50i-codec-analog.txt @@ -0,0 +1,12 @@ +* Allwinner A64 Codec Analog Controls + +Required properties: +- compatible: must be one of the following compatibles: + - "allwinner,sun50i-a64-codec-analog" +- reg: must contain the registers location and length + +Example: + codec_analog: codec-analog@1f015c0 { + compatible = "allwinner,sun50i-a64-codec-analog"; + reg = <0x01f015c0 0x4>; + }; diff --git a/Documentation/devicetree/bindings/sound/ts3a227e.txt b/Documentation/devicetree/bindings/sound/ts3a227e.txt index 3ed8359144d3..21ab45bc7e8f 100644 --- a/Documentation/devicetree/bindings/sound/ts3a227e.txt +++ b/Documentation/devicetree/bindings/sound/ts3a227e.txt @@ -14,7 +14,7 @@ Required properties: Optional properies: - ti,micbias: Intended MICBIAS voltage (datasheet section 9.6.7). - Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage + Select 0/1/2/3/4/5/6/7 to specify MICBIAS voltage 2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V Default value is "1" (2.2V). diff --git a/Documentation/devicetree/bindings/sound/wm8782.txt b/Documentation/devicetree/bindings/sound/wm8782.txt new file mode 100644 index 000000000000..256cdec6ec4d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8782.txt @@ -0,0 +1,17 @@ +WM8782 stereo ADC + +This device does not have any control interface or reset pins. + +Required properties: + + - compatible : "wlf,wm8782" + - Vdda-supply : phandle to a regulator for the analog power supply (2.7V - 5.5V) + - Vdd-supply : phandle to a regulator for the digital power supply (2.7V - 3.6V) + +Example: + +wm8782: stereo-adc { + compatible = "wlf,wm8782"; + Vdda-supply = <&vdda_supply>; + Vdd-supply = <&vdd_supply>; +}; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt new file mode 100644 index 000000000000..790311a42bf1 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt @@ -0,0 +1,39 @@ +GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP v3 core is a GENI based AHB slave that provides a common data path +(an output FIFO and an input FIFO) for serial peripheral interface (SPI) +mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Must contain "qcom,geni-spi". +- reg: Must contain SPI register location and length. +- interrupts: Must contain SPI controller interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- #address-cells: Must be <1> to define a chip select address on + the SPI bus. +- #size-cells: Must be <0>. + +SPI Controller nodes must be child of GENI based Qualcomm Universal +Peripharal. Please refer GENI based QUP wrapper controller node bindings +described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt. + +SPI slave nodes must be children of the SPI master node and conform to SPI bus +binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + spi0: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0xa84000 0x4000>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_spi_2_active>; + pinctrl-1 = <&qup_1_spi_2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt new file mode 100644 index 000000000000..1d64b61f5171 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt @@ -0,0 +1,36 @@ +Qualcomm Quad Serial Peripheral Interface (QSPI) + +The QSPI controller allows SPI protocol communication in single, dual, or quad +wire transmission modes for read/write access to slaves such as NOR flash. + +Required properties: +- compatible: An SoC specific identifier followed by "qcom,qspi-v1", such as + "qcom,sdm845-qspi", "qcom,qspi-v1" +- reg: Should contain the base register location and length. +- interrupts: Interrupt number used by the controller. +- clocks: Should contain the core and AHB clock. +- clock-names: Should be "core" for core clock and "iface" for AHB clock. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + qspi: spi@88df000 { + compatible = "qcom,sdm845-qspi", "qcom,qspi-v1"; + reg = <0x88df000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "iface", "core"; + clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <&gcc GCC_QSPI_CORE_CLK>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bfbc2035fb6b..4b836ad17b19 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -2,7 +2,9 @@ Renesas MSIOF spi controller Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) @@ -11,10 +13,14 @@ Required properties: "renesas,msiof-r8a7795" (R-Car H3) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-r8a77965" (R-Car M3-N) + "renesas,msiof-r8a77970" (R-Car V3M) + "renesas,msiof-r8a77980" (R-Car V3H) + "renesas,msiof-r8a77990" (R-Car E3) + "renesas,msiof-r8a77995" (R-Car D3) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) - "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device) "renesas,sh-msiof" (deprecated) When compatible with the generic version, nodes diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 642d3fb1ef85..2864bc6b659c 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. Required properties: - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or - "jaguar2" + "jaguar2", or "amazon,alpine-dw-apb-ssi" - reg : The register base for the controller. For "mscc,<soc>-spi", a second register set is required (named ICPU_CFG:SPI_MST) - interrupts : One interrupt, used by the controller. diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 4af132606b37..8d178a4503cf 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -3,6 +3,7 @@ Required properties: - compatible : - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc - reg : address and length of the lpspi master registers - interrupts : lpspi interrupt - clocks : lpspi clock specifier diff --git a/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt new file mode 100644 index 000000000000..0335a9bd2e8a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt @@ -0,0 +1,24 @@ +PXA2xx SSP SPI Controller + +Required properties: +- compatible: Must be "marvell,mmp2-ssp". +- reg: Offset and length of the device's register set. +- interrupts: Should be the interrupt number. +- clocks: Should contain a single entry describing the clock input. +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + ssp1: spi@d4035000 { + compatible = "marvell,mmp2-ssp"; + reg = <0xd4035000 0x1000>; + clocks = <&soc_clocks MMP2_CLK_SSP0>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 96fd58548f69..fc97ad64fbf2 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver Required properties: - compatible : For Renesas Serial Peripheral Interface on legacy SH: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. - For Renesas Serial Peripheral Interface on RZ/A1H: + For Renesas Serial Peripheral Interface on RZ/A: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. For Quad Serial Peripheral Interface on R-Car Gen2 and RZ/G1 devices: @@ -11,7 +11,9 @@ Required properties: Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,rspi-r7s9210" (RZ/A2) - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7744" (RZ/G1N) - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt new file mode 100644 index 000000000000..c37e5a179b21 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt @@ -0,0 +1,32 @@ +Binding for MTK SPI Slave controller + +Required properties: +- compatible: should be one of the following. + - mediatek,mt2712-spi-slave: for mt2712 platforms +- reg: Address and length of the register set for the device. +- interrupts: Should contain spi interrupt. +- clocks: phandles to input clocks. + It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>. +- clock-names: should be "spi" for the clock gate. + +Optional properties: +- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>. +- assigned-clock-parents: parent of mux clock. + It's PLL, and should be one of the following. + - <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ. + It's the default one. + - <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ. + - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. + - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + +Example: +- SoC Specific Portion: +spis1: spi@10013000 { + compatible = "mediatek,mt2712-spi-slave"; + reg = <0 0x10013000 0 0x100>; + interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AO_SPI1>; + clock-names = "spi"; + assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt new file mode 100644 index 000000000000..bad211a19da4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -0,0 +1,26 @@ +Spreadtrum SPI Controller + +Required properties: +- compatible: Should be "sprd,sc9860-spi". +- reg: Offset and length of SPI controller register space. +- interrupts: Should contain SPI interrupt. +- clock-names: Should contain following entries: + "spi" for SPI clock, + "source" for SPI source (parent) clock, + "enable" for SPI module enable clock. +- clocks: List of clock input name strings sorted in the same order + as the clock-names property. +- #address-cells: The number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be set to 0. + +Example: +spi0: spi@70a00000{ + compatible = "sprd,sc9860-spi"; + reg = <0 0x70a00000 0 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "spi", "source","enable"; + clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt new file mode 100644 index 000000000000..adeeb63e84b9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -0,0 +1,44 @@ +* STMicroelectronics Quad Serial Peripheral Interface(QSPI) + +Required properties: +- compatible: should be "st,stm32f469-qspi" +- reg: the first contains the register location and length. + the second contains the memory mapping address and length +- reg-names: should contain the reg names "qspi" "qspi_mm" +- interrupts: should contain the interrupt for the device +- clocks: the phandle of the clock needed by the QSPI controller +- A pinctrl must be defined to set pins in mode of operation for QSPI transfer + +Optional properties: +- resets: must contain the phandle to the reset controller. + +A spi flash (NOR/NAND) must be a child of spi node and could have some +properties. Also see jedec,spi-nor.txt. + +Required properties: +- reg: chip-Select number (QSPI controller may connect 2 flashes) +- spi-max-frequency: max frequency of spi bus + +Optional property: +- spi-rx-bus-width: see ./spi-bus.txt for the description + +Example: + +qspi: spi@a0001000 { + compatible = "st,stm32f469-qspi"; + reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <91>; + resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; + clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/sram/sunxi-sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index c51ade86578c..62dd0748f0ef 100644 --- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -18,6 +18,7 @@ Required properties: - "allwinner,sun8i-h3-system-control" - "allwinner,sun50i-a64-sram-controller" (deprecated) - "allwinner,sun50i-a64-system-control" + - "allwinner,sun50i-h6-system-control", "allwinner,sun50i-a64-system-control" - reg : sram controller register offset + length SRAM nodes @@ -54,6 +55,9 @@ The valid sections compatible for H3 are: The valid sections compatible for A64 are: - allwinner,sun50i-a64-sram-c +The valid sections compatible for H6 are: + - allwinner,sun50i-h6-sram-c, allwinner,sun50i-a64-sram-c + Devices using SRAM sections --------------------------- diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt index 290ec06fa33a..0273a92a2a84 100644 --- a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt +++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt @@ -6,8 +6,7 @@ interrupt signal and status register to identify high PMIC die temperature. Required properties: - compatible: Should contain "qcom,spmi-temp-alarm". -- reg: Specifies the SPMI address and length of the controller's - registers. +- reg: Specifies the SPMI address. - interrupts: PMIC temperature alarm interrupt. - #thermal-sensor-cells: Should be 0. See thermal.txt for a description. @@ -20,7 +19,7 @@ Example: pm8941_temp: thermal-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; - reg = <0x2400 0x100>; + reg = <0x2400>; interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; #thermal-sensor-cells = <0>; @@ -36,19 +35,14 @@ Example: thermal-sensors = <&pm8941_temp>; trips { - passive { - temperature = <1050000>; + stage1 { + temperature = <105000>; hysteresis = <2000>; type = "passive"; }; - alert { + stage2 { temperature = <125000>; hysteresis = <2000>; - type = "hot"; - }; - crit { - temperature = <145000>; - hysteresis = <2000>; type = "critical"; }; }; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt index 20ca4ef9d776..04cbb90a5d3e 100644 --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -1,9 +1,9 @@ * Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs Required properties: -- compatible : Must include "fsl,qoriq-tmu". The version of the device is - determined by the TMU IP Block Revision Register (IPBRR0) at - offset 0x0BF8. +- compatible : Must include "fsl,qoriq-tmu" or "fsl,imx8mq-tmu". The + version of the device is determined by the TMU IP Block Revision + Register (IPBRR0) at offset 0x0BF8. Table of correspondences between IPBRR0 values and example chips: Value Device ---------- ----- diff --git a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt index cfa154bb0fa7..ad9a435afef4 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt @@ -7,9 +7,11 @@ inside the LSI. Required properties: - compatible : "renesas,<soctype>-thermal", Examples with soctypes are: + - "renesas,r8a774a1-thermal" (RZ/G2M) - "renesas,r8a7795-thermal" (R-Car H3) - "renesas,r8a7796-thermal" (R-Car M3-W) - "renesas,r8a77965-thermal" (R-Car M3-N) + - "renesas,r8a77980-thermal" (R-Car V3H) - reg : Address ranges of the thermal registers. Each sensor needs one address range. Sorting must be done in increasing order according to datasheet, i.e. @@ -19,7 +21,8 @@ Required properties: Optional properties: -- interrupts : interrupts routed to the TSC (3 for H3, M3-W and M3-N) +- interrupts : interrupts routed to the TSC (3 for H3, M3-W, M3-N, + and V3H) - power-domain : Must contain a reference to the power domain. This property is mandatory if the thermal sensor instance is part of a controllable power domain. diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 67c563f1b4c4..73e1613d2cb0 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -4,15 +4,17 @@ Required properties: - compatible : "renesas,thermal-<soctype>", "renesas,rcar-gen2-thermal" (with thermal-zone) or "renesas,rcar-thermal" (without thermal-zone) as - fallback except R-Car D3. + fallback except R-Car V3M/D3. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) - "renesas,thermal-r8a7743" (RZ/G1M) + - "renesas,thermal-r8a7744" (RZ/G1N) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - "renesas,thermal-r8a7791" (R-Car M2-W) - "renesas,thermal-r8a7792" (R-Car V2H) - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a77970" (R-Car V3M) - "renesas,thermal-r8a77995" (R-Car D3) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register @@ -21,7 +23,7 @@ Required properties: Option properties: - interrupts : If present should contain 3 interrupts for - R-Car D3 or 1 interrupt otherwise. + R-Car V3M/D3 or 1 interrupt otherwise. Example (non interrupt support): diff --git a/Documentation/devicetree/bindings/thermal/stm32-thermal.txt b/Documentation/devicetree/bindings/thermal/stm32-thermal.txt new file mode 100644 index 000000000000..8c0d5a4d8031 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/stm32-thermal.txt @@ -0,0 +1,61 @@ +Binding for Thermal Sensor for STMicroelectronics STM32 series of SoCs. + +On STM32 SoCs, the Digital Temperature Sensor (DTS) is in charge of managing an +analog block which delivers a frequency depending on the internal SoC's +temperature. By using a reference frequency, DTS is able to provide a sample +number which can be translated into a temperature by the user. + +DTS provides interrupt notification mechanism by threshold. This mechanism +offers two temperature trip points: passive and critical. The first is intended +for passive cooling notification while the second is used for over-temperature +reset. + +Required parameters: +------------------- + +compatible: Should be "st,stm32-thermal" +reg: This should be the physical base address and length of the + sensor's registers. +clocks: Phandle of the clock used by the thermal sensor. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +clock-names: Should be "pclk" for register access clock and reference clock. + See: Documentation/devicetree/bindings/resource-names.txt +#thermal-sensor-cells: Should be 0. See ./thermal.txt for a description. +interrupts: Standard way to define interrupt number. + +Example: + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&thermal>; + + trips { + cpu_alert1: cpu-alert1 { + temperature = <85000>; + hysteresis = <0>; + type = "passive"; + }; + + cpu-crit: cpu-crit { + temperature = <120000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + }; + }; + }; + + thermal: thermal@50028000 { + compatible = "st,stm32-thermal"; + reg = <0x50028000 0x100>; + clocks = <&rcc TMPSENS>; + clock-names = "pclk"; + #thermal-sensor-cells = <0>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index eb7ee91556a5..ca14ba959e0d 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -152,7 +152,7 @@ Optional property: Elem size: one cell the sensors listed in the thermal-sensors property. Elem type: signed Coefficients defaults to 1, in case this property is not specified. A simple linear polynomial is used: - Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn. + Z = c0 * x0 + c1 * x1 + ... + c(n-1) * x(n-1) + cn. The coefficients are ordered and they match with sensors by means of sensor ID. Additional coefficients are diff --git a/Documentation/devicetree/bindings/timer/renesas,cmt.txt b/Documentation/devicetree/bindings/timer/renesas,cmt.txt index b40add2d9bb4..33992679a8bd 100644 --- a/Documentation/devicetree/bindings/timer/renesas,cmt.txt +++ b/Documentation/devicetree/bindings/timer/renesas,cmt.txt @@ -24,6 +24,8 @@ Required Properties: - "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4. - "renesas,r8a7743-cmt0" for the 32-bit CMT0 device included in r8a7743. - "renesas,r8a7743-cmt1" for the 48-bit CMT1 device included in r8a7743. + - "renesas,r8a7744-cmt0" for the 32-bit CMT0 device included in r8a7744. + - "renesas,r8a7744-cmt1" for the 48-bit CMT1 device included in r8a7744. - "renesas,r8a7745-cmt0" for the 32-bit CMT0 device included in r8a7745. - "renesas,r8a7745-cmt1" for the 48-bit CMT1 device included in r8a7745. - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790. @@ -34,6 +36,10 @@ Required Properties: - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793. - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794. - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794. + - "renesas,r8a77970-cmt0" for the 32-bit CMT0 device included in r8a77970. + - "renesas,r8a77970-cmt1" for the 48-bit CMT1 device included in r8a77970. + - "renesas,r8a77980-cmt0" for the 32-bit CMT0 device included in r8a77980. + - "renesas,r8a77980-cmt1" for the 48-bit CMT1 device included in r8a77980. - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2 and RZ/G1. @@ -41,6 +47,9 @@ Required Properties: and RZ/G1. These are fallbacks for r8a73a4, R-Car Gen2 and RZ/G1 entries listed above. + - "renesas,rcar-gen3-cmt0" for 32-bit CMT0 devices included in R-Car Gen3. + - "renesas,rcar-gen3-cmt1" for 48-bit CMT1 devices included in R-Car Gen3. + These are fallbacks for R-Car Gen3 entries listed above. - reg: base address and length of the registers block for the timer module. - interrupts: interrupt-specifier for the timer, one per channel. diff --git a/Documentation/devicetree/bindings/timer/renesas,ostm.txt b/Documentation/devicetree/bindings/timer/renesas,ostm.txt index be3ae0fdf775..81a78f8bcf17 100644 --- a/Documentation/devicetree/bindings/timer/renesas,ostm.txt +++ b/Documentation/devicetree/bindings/timer/renesas,ostm.txt @@ -9,7 +9,8 @@ Channels are independent from each other. Required Properties: - compatible: must be one or more of the following: - - "renesas,r7s72100-ostm" for the r7s72100 OSTM + - "renesas,r7s72100-ostm" for the R7S72100 (RZ/A1) OSTM + - "renesas,r7s9210-ostm" for the R7S9210 (RZ/A2) OSTM - "renesas,ostm" for any OSTM This is a fallback for the above renesas,*-ostm entries diff --git a/Documentation/devicetree/bindings/timer/renesas,tmu.txt b/Documentation/devicetree/bindings/timer/renesas,tmu.txt index cd5f20bf2582..4ddff85837da 100644 --- a/Documentation/devicetree/bindings/timer/renesas,tmu.txt +++ b/Documentation/devicetree/bindings/timer/renesas,tmu.txt @@ -12,6 +12,8 @@ Required Properties: - "renesas,tmu-r8a7740" for the r8a7740 TMU - "renesas,tmu-r8a7778" for the r8a7778 TMU - "renesas,tmu-r8a7779" for the r8a7779 TMU + - "renesas,tmu-r8a77970" for the r8a77970 TMU + - "renesas,tmu-r8a77980" for the r8a77980 TMU - "renesas,tmu" for any TMU. This is a fallback for the above renesas,tmu-* entries diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 763a2808a95c..6ab001fa1ed4 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -21,21 +21,10 @@ adi,adt7490 +/-1C TDM Extended Temp Range I.C adi,adxl345 Three-Axis Digital Accelerometer adi,adxl346 Three-Axis Digital Accelerometer (backward-compatibility value "adi,adxl345" must be listed too) ams,iaq-core AMS iAQ-Core VOC Sensor -amstaos,tsl2571 AMS/TAOS ALS and proximity sensor -amstaos,tsl2671 AMS/TAOS ALS and proximity sensor -amstaos,tmd2671 AMS/TAOS ALS and proximity sensor -amstaos,tsl2771 AMS/TAOS ALS and proximity sensor -amstaos,tmd2771 AMS/TAOS ALS and proximity sensor -amstaos,tsl2572 AMS/TAOS ALS and proximity sensor -amstaos,tsl2672 AMS/TAOS ALS and proximity sensor -amstaos,tmd2672 AMS/TAOS ALS and proximity sensor -amstaos,tsl2772 AMS/TAOS ALS and proximity sensor -amstaos,tmd2772 AMS/TAOS ALS and proximity sensor at,24c08 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor capella,cm3232 CM3232: Ambient Light Sensor -cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1631 High-Precision Digital Thermometer dallas,ds1672 Dallas DS1672 Real-time Clock diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 2e9318151df7..529e51879fb2 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -80,6 +80,8 @@ Optional properties: controller. It's expected that a mux state of 0 indicates device mode and a mux state of 1 indicates host mode. - mux-control-names: Shall be "usb_switch" if mux-controls is specified. +- pinctrl-names: Names for optional pin modes in "default", "host", "device" +- pinctrl-n: alternate pin modes i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 46da5f184460..6dc3c4a34483 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -6,6 +6,7 @@ Required properties: - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC. - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; + - "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 3e4c38b806ac..636630fb92d7 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -19,6 +19,7 @@ Exception for clocks: "cavium,octeon-7130-usb-uctl" "qcom,dwc3" "samsung,exynos5250-dwusb3" + "samsung,exynos5433-dwusb3" "samsung,exynos7-dwusb3" "sprd,sc9860-dwc3" "st,stih407-dwc3" diff --git a/Documentation/devicetree/bindings/usb/ehci-mv.txt b/Documentation/devicetree/bindings/usb/ehci-mv.txt new file mode 100644 index 000000000000..335589895763 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-mv.txt @@ -0,0 +1,23 @@ +* Marvell PXA/MMP EHCI controller. + +Required properties: + +- compatible: must be "marvell,pxau2o-ehci" +- reg: physical base addresses of the controller and length of memory mapped region +- interrupts: one EHCI controller interrupt should be described here +- clocks: phandle list of usb clocks +- clock-names: should be "USBCLK" +- phys: phandle for the PHY device +- phy-names: should be "usb" + +Example: + + ehci0: usb-ehci@d4208000 { + compatible = "marvell,pxau2o-ehci"; + reg = <0xd4208000 0x200>; + interrupts = <44>; + clocks = <&soc_clocks MMP2_CLK_USB>; + clock-names = "USBCLK"; + phys = <&usb_otg_phy>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index c97374315049..b7111f43fa59 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -83,6 +83,8 @@ Required properties: - compatible: should be one of the following - "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on Exynos5250/5420. + "samsung,exynos5433-dwusb3": for USB 3.0 DWC3 controller on + Exynos5433. "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. - #address-cells, #size-cells : should be '1' if the device has sub-nodes with 'reg' property. diff --git a/Documentation/devicetree/bindings/usb/faraday,fotg210.txt b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt new file mode 100644 index 000000000000..06a2286e2054 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt @@ -0,0 +1,35 @@ +Faraday FOTG Host controller + +This OTG-capable USB host controller is found in Cortina Systems +Gemini and other SoC products. + +Required properties: +- compatible: should be one of: + "faraday,fotg210" + "cortina,gemini-usb", "faraday,fotg210" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: +- clocks: should contain the IP block clock +- clock-names: should be "PCLK" for the IP block clock + +Required properties for "cortina,gemini-usb" compatible: +- syscon: a phandle to the system controller to access PHY registers + +Optional properties for "cortina,gemini-usb" compatible: +- cortina,gemini-mini-b: boolean property that indicates that a Mini-B + OTG connector is in use +- wakeup-source: see power/wakeup-source.txt + +Example for Gemini: + +usb@68000000 { + compatible = "cortina,gemini-usb", "faraday,fotg210"; + reg = <0x68000000 0x1000>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cc 12>; + clock-names = "PCLK"; + syscon = <&syscon>; + wakeup-source; +}; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 6087dc7f209e..a5d011d2efc8 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -5,10 +5,19 @@ Required properties : - reg : I2C slave address - interrupts : Interrupt specifier -Optional properties : -- fcs,operating-sink-microwatt : - Minimum amount of power accepted from a sink - when negotiating +Required sub-node: +- connector : The "usb-c-connector" attached to the FUSB302 IC. The bindings + of the connector node are specified in: + + Documentation/devicetree/bindings/connector/usb-connector.txt + +Deprecated properties : +- fcs,max-sink-microvolt : Maximum sink voltage accepted by port controller +- fcs,max-sink-microamp : Maximum sink current accepted by port controller +- fcs,max-sink-microwatt : Maximum sink power accepted by port controller +- fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink + when negotiating + Example: @@ -17,7 +26,16 @@ fusb302: typec-portc@54 { reg = <0x54>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - fcs,max-sink-microvolt = <12000000>; - fcs,max-sink-microamp = <3000000>; - fcs,max-sink-microwatt = <36000000>; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(3000, 12000, 3000) + PDO_PPS_APDO(3000, 11000, 3000)>; + op-sink-microwatt = <10000000>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index 2c071bb5801e..d366555166d0 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -2,11 +2,13 @@ Renesas Electronics USB3.0 Peripheral driver Required properties: - compatible: Must contain one of the following: + - "renesas,r8a774a1-usb3-peri" - "renesas,r8a7795-usb3-peri" - "renesas,r8a7796-usb3-peri" - "renesas,r8a77965-usb3-peri" - - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 compatible - device + - "renesas,r8a77990-usb3-peri" + - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 or RZ/G2 + compatible device When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 43960faf5a88..90719f501852 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -4,7 +4,9 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device + - "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device + - "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device @@ -13,10 +15,11 @@ Required properties: - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device + - "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device - "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices - - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device + - "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices - "renesas,rza1-usbhs" for RZ/A1 compatible device When compatible with the generic version, nodes must list the @@ -25,7 +28,11 @@ Required properties: - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - - clocks: A list of phandle + clock specifier pairs + - clocks: A list of phandle + clock specifier pairs. + - In case of "renesas,rcar-gen3-usbhs", two clocks are required. + First clock should be peripheral and second one should be host. + - In case of except above, one clock is required. First clock + should be peripheral. Optional properties: - renesas,buswait: Integer to use BUSWAIT register diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index 0f1b75386207..406252d14c6b 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,7 +15,11 @@ Optional properties: - needs-reset-on-resume : boolean, set this to force EHCI reset after resume - has-transaction-translator : boolean, set this if EHCI have a Transaction Translator built into the root hub. - - clocks : a list of phandle + clock specifier pairs + - clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : phandle + reset specifier pair diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index a8d2103d1f3d..aaaa5255c972 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,7 +12,11 @@ Optional properties: - no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA - remote-wakeup-connected: remote wakeup is wired on the platform - num-ports : u32, to override the detected port count -- clocks : a list of phandle + clock specifier pairs +- clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : a list of phandle + reset specifier pairs diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index ac4cd0d6195a..fea8b1545751 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -8,6 +8,8 @@ Required properties: - "marvell,armada-375-xhci" for Armada 375 SoCs - "marvell,armada-380-xhci" for Armada 38x SoCs - "renesas,xhci-r8a7743" for r8a7743 SoC + - "renesas,xhci-r8a7744" for r8a7744 SoC + - "renesas,xhci-r8a774a1" for r8a774a1 SoC - "renesas,xhci-r8a7790" for r8a7790 SoC - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC @@ -17,7 +19,8 @@ Required properties: - "renesas,xhci-r8a77990" for r8a77990 SoC - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 or RZ/G1 compatible device - - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 or RZ/G2 compatible + device - "xhci-platform" (deprecated) When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2c3fc512e746..4b1a2a8fcc16 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -84,6 +84,7 @@ cosmic Cosmic Circuits crane Crane Connectivity Solutions creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. +csky Hangzhou C-SKY Microsystems Co., Ltd cubietech Cubietech, Ltd. cypress Cypress Semiconductor Corporation cznic CZ.NIC, z.s.p.o. @@ -114,6 +115,7 @@ elan Elan Microelectronic Corp. embest Shenzhen Embest Technology Co., Ltd. emmicro EM Microelectronic emtrion emtrion GmbH +endless Endless Mobile, Inc. energymicro Silicon Laboratories (formerly Energy Micro AS) engicam Engicam S.r.l. epcos EPCOS AG @@ -127,6 +129,7 @@ everspin Everspin Technologies, Inc. exar Exar Corporation excito Excito ezchip EZchip Semiconductor +facebook Facebook fairphone Fairphone B.V. faraday Faraday Technology Corporation fastrax Fastrax Oy @@ -235,6 +238,7 @@ micrel Micrel Inc. microchip Microchip Technology Inc. microcrystal Micro Crystal AG micron Micron Technology Inc. +mikroe MikroElektronika d.o.o. minix MINIX Technology Ltd. miramems MiraMEMS Sensing Technology Co., Ltd. mitsubishi Mitsubishi Electric Corporation @@ -274,6 +278,7 @@ nxp NXP Semiconductors okaya Okaya Electric America, Inc. oki Oki Electric Industry Co., Ltd. olimex OLIMEX Ltd. +olpc One Laptop Per Child onion Onion Corporation onnn ON Semiconductor Corp. ontat On Tat Industrial Company @@ -297,6 +302,7 @@ pine64 Pine64 pixcir PIXCIR MICROELECTRONICS Co., Ltd plathome Plat'Home Co., Ltd. plda PLDA +plx Broadcom Corporation (formerly PLX Technology) portwell Portwell Inc. poslab Poslab Technology Co., Ltd. powervr PowerVR (deprecated, use img) diff --git a/Documentation/devicetree/bindings/watchdog/armada-37xx-wdt.txt b/Documentation/devicetree/bindings/watchdog/armada-37xx-wdt.txt new file mode 100644 index 000000000000..a8d00c31a1d8 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/armada-37xx-wdt.txt @@ -0,0 +1,23 @@ +* Armada 37xx CPU Watchdog Timer Controller + +Required properties: +- compatible : must be "marvell,armada-3700-wdt" +- reg : base physical address of the controller and length of memory mapped + region. +- clocks : the clock feeding the watchdog timer. See clock-bindings.txt +- marvell,system-controller : reference to syscon node for the CPU Miscellaneous + Registers + +Example: + + cpu_misc: system-controller@d000 { + compatible = "marvell,armada-3700-cpu-misc", "syscon"; + reg = <0xd000 0x1000>; + }; + + wdt: watchdog@8300 { + compatible = "marvell,armada-3700-wdt"; + reg = <0x8300 0x40>; + marvell,system-controller = <&cpu_misc>; + clocks = <&xtalclk>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/mpc8xxx-wdt.txt b/Documentation/devicetree/bindings/watchdog/mpc8xxx-wdt.txt new file mode 100644 index 000000000000..a384ff5b3ce8 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/mpc8xxx-wdt.txt @@ -0,0 +1,25 @@ +* Freescale mpc8xxx watchdog driver (For 83xx, 86xx and 8xx) + +Required properties: +- compatible: Shall contain one of the following: + "mpc83xx_wdt" for an mpc83xx + "fsl,mpc8610-wdt" for an mpc86xx + "fsl,mpc823-wdt" for an mpc8xx +- reg: base physical address and length of the area hosting the + watchdog registers. + On the 83xx, "Watchdog Timer Registers" area: <0x200 0x100> + On the 86xx, "Watchdog Timer Registers" area: <0xe4000 0x100> + On the 8xx, "General System Interface Unit" area: <0x0 0x10> + +Optional properties: +- reg: additional physical address and length (4) of location of the + Reset Status Register (called RSTRSCR on the mpc86xx) + On the 83xx, it is located at offset 0x910 + On the 86xx, it is located at offset 0xe0094 + On the 8xx, it is located at offset 0x288 + +Example: + WDT: watchdog@0 { + compatible = "fsl,mpc823-wdt"; + reg = <0x0 0x10 0x288 0x4>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index 5d47a262474c..a8ee29fd9ac8 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -6,7 +6,9 @@ Required properties: version. Examples with soctypes are: - "renesas,r8a7743-wdt" (RZ/G1M) + - "renesas,r8a7744-wdt" (RZ/G1N) - "renesas,r8a7745-wdt" (RZ/G1E) + - "renesas,r8a774a1-wdt" (RZ/G2M) - "renesas,r8a7790-wdt" (R-Car H2) - "renesas,r8a7791-wdt" (R-Car M2-W) - "renesas,r8a7792-wdt" (R-Car V2H) @@ -19,10 +21,11 @@ Required properties: - "renesas,r8a77990-wdt" (R-Car E3) - "renesas,r8a77995-wdt" (R-Car D3) - "renesas,r7s72100-wdt" (RZ/A1) + - "renesas,r7s9210-wdt" (RZ/A2) The generic compatible string must be: - "renesas,rza-wdt" for RZ/A - - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G - - "renesas,rcar-gen3-wdt" for R-Car Gen3 + - "renesas,rcar-gen2-wdt" for R-Car Gen2 and RZ/G1 + - "renesas,rcar-gen3-wdt" for R-Car Gen3 and RZ/G2 - reg : Should contain WDT registers location and length - clocks : the clock feeding the watchdog timer. |