summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2013-06-13macvlan: don't touch promisc without passthroughMichael S. Tsirkin1-7/+13
commit df8ef8f3aaa6692970a436204c4429210addb23a "macvlan: add FDB bridge ops and macvlan flags" added a way to control NOPROMISC macvlan flag through netlink. However, with a non passthrough device we never set promisc on open, even if NOPROMISC is off. As a result: If userspace clears NOPROMISC on open, then does not clear it on a netlink command, promisc counter is not decremented on stop and there will be no way to clear it once macvlan is detached. If userspace does not clear NOPROMISC on open, then sets NOPROMISC on a netlink command, promisc counter will be decremented from 0 and overflow to fffffffff with no way to clear promisc. To fix, simply ignore NOPROMISC flag in a netlink command for non-passthrough devices, same as we do at open/close. Since we touch this code anyway - check dev_set_promiscuity return code and pass it to users (though an error here is unlikely). Cc: "David S. Miller" <davem@davemloft.net> Reviewed-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-13md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in placeH. Peter Anvin3-5/+6
There are cases where the kernel will believe that the WRITE SAME command is supported by a block device which does not, in fact, support WRITE SAME. This currently happens for SATA drivers behind a SAS controller, but there are probably a hundred other ways that can happen, including drive firmware bugs. After receiving an error for WRITE SAME the block layer will retry the request as a plain write of zeroes, but mdraid will consider the failure as fatal and consider the drive failed. This has the effect that all the mirrors containing a specific set of data are each offlined in very rapid succession resulting in data loss. However, just bouncing the request back up to the block layer isn't ideal either, because the whole initial request-retry sequence should be inside the write bitmap fence, which probably means that md needs to do its own conversion of WRITE SAME to write zero. Until the failure scenario has been sorted out, disable WRITE SAME for raid1, raid5, and raid10. [neilb: added raid5] This patch is appropriate for any -stable since 3.7 when write_same support was added. Cc: stable@vger.kernel.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-06-13md/raid1,raid10: use freeze_array in place of raise_barrier in various places.NeilBrown2-18/+18
Various places in raid1 and raid10 are calling raise_barrier when they really should call freeze_array. The former is only intended to be called from "make_request". The later has extra checks for 'nr_queued' and makes a call to flush_pending_writes(), so it is safe to call it from within the management thread. Using raise_barrier will sometimes deadlock. Using freeze_array should not. As 'freeze_array' currently expects one request to be pending (in handle_read_error - the only previous caller), we need to pass it the number of pending requests (extra) to ignore. The deadlock was made particularly noticeable by commits 050b66152f87c7 (raid10) and 6b740b8d79252f13 (raid1) which appeared in 3.4, so the fix is appropriate for any -stable kernel since then. This patch probably won't apply directly to some early kernels and will need to be applied by hand. Cc: stable@vger.kernel.org Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-06-13md/raid1: consider WRITE as successful only if at least one non-Faulty and ↵Alex Lyakas2-2/+22
non-rebuilding drive completed it. Without that fix, the following scenario could happen: - RAID1 with drives A and B; drive B was freshly-added and is rebuilding - Drive A fails - WRITE request arrives to the array. It is failed by drive A, so r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B succeeds in writing it, so the same r1_bio is marked as R1BIO_Uptodate. - r1_bio arrives to handle_write_finished, badblocks are disabled, md_error()->error() does nothing because we don't fail the last drive of raid1 - raid_end_bio_io() calls call_bio_endio() - As a result, in call_bio_endio(): if (!test_bit(R1BIO_Uptodate, &r1_bio->state)) clear_bit(BIO_UPTODATE, &bio->bi_flags); this code doesn't clear the BIO_UPTODATE flag, and the whole master WRITE succeeds, back to the upper layer. So we returned success to the upper layer, even though we had written the data onto the rebuilding drive only. But when we want to read the data back, we would not read from the rebuilding drive, so this data is lost. [neilb - applied identical change to raid10 as well] This bug can result in lost data, so it is suitable for any -stable kernel. Cc: stable@vger.kernel.org Signed-off-by: Alex Lyakas <alex@zadarastorage.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-06-13md: md_stop_writes() should always freeze recovery.NeilBrown1-1/+1
__md_stop_writes() will currently sometimes freeze recovery. So any caller must be ready for that to happen, and indeed they are. However if __md_stop_writes() doesn't freeze_recovery, then a recovery could start before mddev_suspend() is called, which could be awkward. This can particularly cause problems or dm-raid. So change __md_stop_writes() to always freeze recovery. This is safe and more predicatable. Reported-by: Brassow Jonathan <jbrassow@redhat.com> Tested-by: Brassow Jonathan <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
2013-06-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds32-97/+251
Pull networking update from David Miller: 1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to dump all objects properly, from Pablo Neira Ayuso. 2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is present. Fix from Phil Oester. 3) qdisc_get_rtab() looks for an existing matching rate table and uses that instead of creating a new one. However, it's key matching is incomplete, it fails to check to make sure the ->data[] array is identical too. Fix from Eric Dumazet. 4) ip_vs_dest_entry isn't fully initialized before copying back to userspace, fix from Dan Carpenter. 5) Fix ubuf reference counting regression in vhost_net, from Jason Wang. 6) When sock_diag dumps a socket filter back to userspace, we have to translate it out of the kernel's internal representation first. From Nicolas Dichtel. 7) davinci_mdio holds a spinlock while calling pm_runtime, which sleeps. Fix from Sebastian Siewior. 8) Timeout check in sh_eth_check_reset is off by one, from Sergei Shtylyov. 9) If sctp socket init fails, we can NULL deref during cleanup. Fix from Daniel Borkmann. 10) netlink_mmap() does not propagate errors properly, from Patrick McHardy. 11) Disable powersave and use minstrel by default in ath9k. From Sujith Manoharan. 12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets which prevents vhost from being able to use zerocopy. From Jason Wang. 13) Fix race between port lookup and TX path in team driver, from Jiri Pirko. 14) Missing length checks in bluetooth L2CAP packet parsing, from Johan Hedberg. 15) rtlwifi fails to connect to networking using any encryption method other than WPA2. Fix from Larry Finger. 16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power management stuff. From Yijing Wang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits) b43: stop format string leaking into error msgs ath9k: Use minstrel rate control by default Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity" ath9k: Disable PowerSave by default net: wireless: iwlegacy: fix build error for il_pm_ops rtlwifi: Fix a false leak indication for PCI devices wl12xx/wl18xx: scan all 5ghz channels wl12xx: increase minimum singlerole firmware version required wl12xx: fix minimum required firmware version for wl127x multirole rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks mwifiex: debugfs: Fix out of bounds array access Bluetooth: Fix mgmt handling of power on failures Bluetooth: Fix missing length checks for L2CAP signalling PDUs Bluetooth: btmrvl: support Marvell Bluetooth device SD8897 Bluetooth: Fix checks for LE support on LE-only controllers team: fix checks in team_get_first_port_txable_rcu() team: move add to port list before port enablement team: check return value of team_get_port_by_index_rcu() for NULL tuntap: set SOCK_ZEROCOPY flag during open netlink: fix error propagation in netlink_mmap() ...
2013-06-12Merge branch 'for-linus' of ↵Linus Torvalds1-4/+7
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid Pull input layer bugfix from Jiri Kosina: "Memory leak regression fix from Benjamin Tissoires" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: multitouch: prevent memleak with the allocated name
2013-06-12Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds8-128/+109
Pull block layer fixes from Jens Axboe: "Outside of bcache (which really isn't super big), these are all few-liners. There are a few important fixes in here: - Fix blk pm sleeping when holding the queue lock - A small collection of bcache fixes that have been done and tested since bcache was included in this merge window. - A fix for a raid5 regression introduced with the bio changes. - Two important fixes for mtip32xx, fixing an oops and potential data corruption (or hang) due to wrong bio iteration on stacked devices." * 'for-linus' of git://git.kernel.dk/linux-block: scatterlist: sg_set_buf() argument must be in linear mapping raid5: Initialize bi_vcnt pktcdvd: silence static checker warning block: remove refs to XD disks from documentation blkpm: avoid sleep when holding queue lock mtip32xx: Correctly handle bio->bi_idx != 0 conditions mtip32xx: Fix NULL pointer dereference during module unload bcache: Fix error handling in init code bcache: clarify free/available/unused space bcache: drop "select CLOSURES" bcache: Fix incompatible pointer type warning
2013-06-12Merge branch 'akpm' (updates from Andrew Morton)Linus Torvalds6-38/+134
Merge misc fixes from Andrew Morton: "Bunch of fixes and one little addition to math64.h" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits) include/linux/math64.h: add div64_ul() mm: memcontrol: fix lockless reclaim hierarchy iterator frontswap: fix incorrect zeroing and allocation size for frontswap_map kernel/audit_tree.c:audit_add_tree_rule(): protect `rule' from kill_rules() mm: migration: add migrate_entry_wait_huge() ocfs2: add missing lockres put in dlm_mig_lockres_handler mm/page_alloc.c: fix watermark check in __zone_watermark_ok() drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info() aio: fix io_destroy() regression by using call_rcu() rtc-at91rm9200: use shadow IMR on at91sam9x5 rtc-at91rm9200: add shadow interrupt mask rtc-at91rm9200: refactor interrupt-register handling rtc-at91rm9200: add configuration support rtc-at91rm9200: add match-table compile guard fs/ocfs2/namei.c: remove unecessary ERROR when removing non-empty directory swap: avoid read_swap_cache_async() race to deadlock while waiting on discard I/O completion drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with device tree cciss: fix broken mutex usage in ioctl audit: wait_for_auditd() should use TASK_UNINTERRUPTIBLE drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel ...
2013-06-12drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info()Dan Carpenter1-0/+1
The "info.fill" array isn't initialized so it can leak uninitialized stack information to user space. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Robin Holt <holt@sgi.com> Acked-by: Dimitri Sivanich <sivanich@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12rtc-at91rm9200: use shadow IMR on at91sam9x5Johan Hovold1-0/+7
Add support for the at91sam9x5-family which must use the shadow interrupt mask due to a hardware issue (causing RTC_IMR to always be zero). Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Robert Nelson <Robert.Nelson@digikey.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12rtc-at91rm9200: add shadow interrupt maskJohan Hovold1-1/+38
Add shadow interrupt-mask register which can be used on SoCs where the actual hardware register is broken. Note that some care needs to be taken to make sure the shadow mask corresponds to the actual hardware state. The added overhead is not an issue for the non-broken SoCs due to the relatively infrequent interrupt-mask updates. We do, however, only use the shadow mask value as a fall-back when it actually needed as there is still a theoretical possibility that the mask is incorrect (see the code for details). Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Robert Nelson <Robert.Nelson@digikey.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12rtc-at91rm9200: refactor interrupt-register handlingJohan Hovold1-14/+29
Add accessors for the interrupt register. This will allow us to easily add a shadow interrupt-mask register to use on SoCs where the interrupt-mask register cannot be used. Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Robert Nelson <Robert.Nelson@digikey.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12rtc-at91rm9200: add configuration supportJohan Hovold1-8/+38
Add configuration support which can be used to implement SoC-specific workarounds for broken hardware. Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Robert Nelson <Robert.Nelson@digikey.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12rtc-at91rm9200: add match-table compile guardJohan Hovold1-0/+2
The members of Atmel's at91sam9x5 family (9x5) have a broken RTC interrupt mask register (AT91_RTC_IMR). It does not reflect enabled interrupts but instead always returns zero. The kernel's rtc-at91rm9200 driver handles the RTC for the 9x5 family. Currently when the date/time is set, an interrupt is generated and this driver neglects to handle the interrupt. The kernel complains about the un-handled interrupt and disables it henceforth. This not only breaks the RTC function, but since that interrupt is shared (Atmel's SYS interrupt) then other things break as well (e.g. the debug port no longer accepts characters). Tested on the at91sam9g25. Bug confirmed by Atmel. This patch (of 5): Add missing match-table compile guard. Signed-off-by: Johan Hovold <jhovold@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: Robert Nelson <Robert.Nelson@digikey.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with ↵Tony Lindgren1-0/+1
device tree When booted in legacy mode device_init_wakeup() gets called by drivers/mfd/twl-core.c when the children are initialized. However, when booted using device tree, the children are created with of_platform_populate() instead add_children(). This means that the RTC driver will not have device_init_wakeup() set, and we need to call it from the driver probe like RTC drivers typically do. Without this we cannot test PM wake-up events on omaps for cases where there may not be any physical wake-up event. Signed-off-by: Tony Lindgren <tony@atomide.com> Reported-by: Kevin Hilman <khilman@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jingoo Han <jg1.han@samsung.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12cciss: fix broken mutex usage in ioctlStephen M. Cameron1-16/+16
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked (as is normal with the Array Configuration Utility) the process will hang as below. It attempts to acquire the same mutex twice, once in do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive, the mutex isn't. Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013 [...] acu D 0000000000000001 0 3246 3191 0x00000080 Call Trace: schedule+0x29/0x70 schedule_preempt_disabled+0xe/0x10 __mutex_lock_slowpath+0x17b/0x220 mutex_lock+0x2b/0x50 cciss_unlocked_open+0x2f/0x110 [cciss] __blkdev_get+0xd3/0x470 blkdev_get+0x5c/0x1e0 register_disk+0x182/0x1a0 add_disk+0x17c/0x310 cciss_add_disk+0x13a/0x170 [cciss] cciss_update_drive_info+0x39b/0x480 [cciss] rebuild_lun_table+0x258/0x370 [cciss] cciss_ioctl+0x34f/0x470 [cciss] do_ioctl+0x49/0x70 [cciss] __blkdev_driver_ioctl+0x28/0x30 blkdev_ioctl+0x200/0x7b0 block_ioctl+0x3c/0x40 do_vfs_ioctl+0x89/0x350 SyS_ioctl+0xa1/0xb0 system_call_fastpath+0x16/0x1b This mutex usage was added into the ioctl path when the big kernel lock was removed. As it turns out, these paths are all thread safe anyway (or can easily be made so) and we don't want ioctl() to be single threaded in any case. Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mike Miller <mike.miller@hp.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channelDerek Basehore1-1/+3
During resume, we call hpet_rtc_timer_init after masking an irq bit in hpet. This will cause the call to hpet_disable_rtc_channel to be undone if RTC_AIE is the only bit not masked. Allowing the cmos interrupt handler to run before resuming caused some issues where the timer for the alarm was not removed. This would cause other, later timers to not be cleared, so utilities such as hwclock would time out when waiting for the update interrupt. [akpm@linux-foundation.org: coding-style tweak] Signed-off-by: Derek Basehore <dbasehore@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12drivers/rtc/rtc-tps6586x.c: device wakeup flags correctionDmitry Osipenko1-1/+2
Use device_init_wakeup() instead of device_set_wakeup_capable() and move it before rtc dev registering. This fixes alarmtimer not registered when tps6586x rtc is the only wakeup compatible rtc in the system. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-06-12tun: Turn tun_flow_init() into void fnPavel Emelyanov1-7/+2
This routine doesn't fail since 9fdc6bef (tuntap: dont use a private kmem_cache) so it makes sense to compact the code a little bit. Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12tun: Report "persist" flag to userspacePavel Emelyanov1-0/+3
The TUN_PERSIST flag is not reported at all -- both TUNGETIFF, and sysfs "flags" attribute skip one. Knowing whether a device is persistent or not is critical for checkpoint-restore, thus I propose to add the read-only IFF_PERSIST one for this. Setting this new IFF_PERSIST is hardly possible, as TUNSETIFF doesn't check for unknown flags being zero and thus there can be trash. Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12Merge branch 'for-davem' of ↵David S. Miller161-2070/+18914
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next John W. Linville says: ==================== This pull request is intended for the 3.11 stream... One big highlight is the cw1200 driver the ST-E CW1100 & CW1200 WLAN chipsets. This one has been lingering for a while, lacking some review comments. Once started getting pulled into linux-next, it got a bit more attention and a number of improvements were made over the initial cut. No doubt there will be more changes ahead, but I think it is looking alright at this point. Along with that, there is the usual flurry of updates to the mac80211 core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other drivers. A few of the highlights are some rt2x00 refactoring/cleanup by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw Gruszka, some iwlwifi power management updates from Alexander Bondar, some enhanced bcma SPROM support from Rafał Miłecki, and a variety of other things here and there. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12sh_eth: split 'sh_eth_netdev_ops'Sergei Shtylyov1-9/+20
Commit 9f86134155047720a3685cda21467f68695152d2 (sh_eth: remove SH_ETH_HAS_TSU) removes 'const' from 'sh_eth_netdev_ops' and modifies it in case TSU registers are present. I've originally suggested to Iwamatsu-san to split this structure in two instead and afterwards Dave M. suggested doing the same. Split 'sh_eth_netdev_ops_tsu' from 'sh_eth_netdev_ops', making both 'const', and assigning 'ndev->detdev_ops' depending on the presence of TSU registers. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds4-23/+68
Pull drm fixes from Dave Airlie: "Just some GMA500 memory leaks and i915 regression fix due to a regression fix" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/i915: prefer VBT modes for SVDO-LVDS over EDID drm/i915: Enable hotplug interrupts after querying hw capabilities. drm/i915: Fix hotplug interrupt enabling for SDVOC drm/gma500/cdv: Fix cursor gem obj referencing on cdv drm/gma500/psb: Fix cursor gem obj referencing on psb drm/gma500/cdv: Unpin framebuffer on crtc disable drm/gma500/psb: Unpin framebuffer on crtc disable drm/gma500: Add fb gtt offset to fb base
2013-06-12Merge branch 'for-john' of ↵John W. Linville5-3/+7
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
2013-06-12rt2800: fix RT5390 & RT3290 TX power settings regressionStanislaw Gruszka1-11/+18
My change: commit cee2c7315f60beeff6137ee59e99acc77d636eeb Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Oct 5 13:44:09 2012 +0200 rt2800: use BBP_R1 for setting tx power unfortunately does not work well with RT5390 and RT3290 chips as they require different temperature compensation TX power settings (TSSI tuning). Since that commit make wireless connection very unstable on those chips, restore previous behavior to fix regression. Once we implement proper TSSI tuning on 5390/3290 we can restore back setting TX power by BBP_R1 register for those chips. Reported-and-tested-by: Mike Romberg <mike-romberg@comcast.net> Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12brcmsmac: disable power-save related functionsArend van Spriel1-15/+2
This patch fixes a regression introduced by: commit 6da3b6c48d79da96a36c2632053cf4f53bf48fb2 Author: Hauke Mehrtens <hauke@hauke-m.de> Date: Sun Mar 24 01:45:52 2013 +0100 brcmsmac: remove brcms_bss_cfg->associated The regression behaviour was described on mailing list. http://mid.gmane.org/5197DC4F.7030503@broadcom.com: "On laptop I installed kernel with brcmsmac compiled as module. It comes up and associates during boot, but after logging in there is no connectivity. Triggering reassoc gives connectivity for some time, but after a while (1-2 min) it stops." Before the mentioned commit the return value of the function brcms_c_ps_allowed() was always false, which is desired behaviour as power-save is not supported at the moment. Therefor, the function is changed to just return false instead of simply reverting the mentioned commit. Bug: 58471 <https://bugzilla.kernel.org/show_bug.cgi?id=58471> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12iwlegacy: fix rate control regressionStanislaw Gruszka2-1/+2
Since driver does not use control.rates[0].count, we have never set that variable. But currently, after rate control API rewrite, this is required by mac80211. Otherwise legacy rates control does not work and we transmit always at 1Mbit/s on pre 11n networks. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12Merge branch 'for-linus' of ↵Linus Torvalds1-15/+18
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client Pull ceph fixes from Sage Weil: "There is a pair of fixes for double-frees in the recent bundle for 3.10, a couple of fixes for long-standing bugs (sleep while atomic and an endianness fix), and a locking fix that can be triggered when osds are going down" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: rbd: fix cleanup in rbd_add() rbd: don't destroy ceph_opts in rbd_add() ceph: ceph_pagelist_append might sleep while atomic ceph: add cpu_to_le32() calls when encoding a reconnect capability libceph: must hold mutex for reset_changed_osds()
2013-06-12Merge branch 'master' of ↵John W. Linville21-73/+211
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-06-12b43: stop format string leaking into error msgsKees Cook1-1/+1
The module parameter "fwpostfix" is userspace controllable, unfiltered, and is used to define the firmware filename. b43_do_request_fw() populates ctx->errors[] on error, containing the firmware filename. b43err() parses its arguments as a format string. For systems with b43 hardware, this could lead to a uid-0 to ring-0 escalation. CVE-2013-2852 Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12ath9k: Use minstrel rate control by defaultSujith Manoharan4-9/+9
The ath9k rate control algorithm has various architectural issues that make it a poor fit in scenarios like congested environments etc. An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191 Change the default to minstrel which is more robust in such cases. The ath9k RC code is left in the driver for now, maybe it can be removed altogether later on. Cc: stable@vger.kernel.org Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"Felix Fietkau1-5/+5
This reverts commit 68d9e1fa24d9c7c2e527f49df8d18fb8cf0ec943 This change reduces rx sensitivity with no apparent extra benefit. It looks like it was meant for testing in a specific scenario, but it was never properly validated. Cc: rmanohar@qca.qualcomm.com Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12ath9k: Disable PowerSave by defaultSujith Manoharan1-2/+1
Almost all the DMA issues which have plagued ath9k (in station mode) for years are related to PS. Disabling PS usually "fixes" the user's connection stablility. Reports of DMA problems are still trickling in and are sitting in the kernel bugzilla. Until the PS code in ath9k is given a thorough review, disbale it by default. The slight increase in chip power consumption is a small price to pay for improved link stability. Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12net: wireless: iwlegacy: fix build error for il_pm_opsYijing Wang1-3/+3
Fix build error for il_pm_ops if CONFIG_PM is set but CONFIG_PM_SLEEP is not set. ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined! ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 Signed-off-by: Yijing Wang <wangyijing@huawei.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: netdev@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: Jingoo Han <jg1.han@samsung.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12rtlwifi: Fix a false leak indication for PCI devicesLarry Finger1-0/+1
This false leak indication is avoided with a no-leak annotation to kmemleak. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12wl12xx/wl18xx: scan all 5ghz channelsEliad Peller2-2/+2
Due to a typo, the current code copies only sizeof(cmd->channels_2) bytes, which is smaller than the correct sizeof(cmd->channels_5) size, resulting in a partial scan (some channels are skipped). Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12wl12xx: increase minimum singlerole firmware version requiredLuciano Coelho1-2/+2
The minimum firmware version required for singlerole after recent driver changes is 6/7.3.10.0.133. Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12wl12xx: fix minimum required firmware version for wl127x multiroleLuciano Coelho1-1/+1
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify multi-role and single-role fw versions), which was causing the multirole firmware for wl127x (WiLink6) to be rejected. The actual minimum version needed for wl127x multirole is 6.5.7.0.42. Reported-by: Levi Pearson <levipearson@gmail.com> Reported-by: Michael Scott <hashcode0f@gmail.com> Cc: stable@kernel.org # 3.9+ Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networksLarry Finger7-41/+139
Driver rtl8192cu can connect to WPA2 networks, but fails for any other encryption method. The cause is a failure to set the rate control data blocks. These changes fix https://bugzilla.redhat.com/show_bug.cgi?id=952793 and https://bugzilla.redhat.com/show_bug.cgi?id=761525. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12mwifiex: debugfs: Fix out of bounds array accessMark A. Greer1-5/+17
When reading the contents of '/sys/kernel/debug/mwifiex/p2p0/info', the following panic occurs: $ cat /sys/kernel/debug/mwifiex/p2p0/info Unable to handle kernel paging request at virtual address 74706164 pgd = de530000 [74706164] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: phy_twl4030_usb omap2430 musb_hdrc mwifiex_sdio mwifiex CPU: 0 PID: 1635 Comm: cat Not tainted 3.10.0-rc1-00010-g1268390 #1 task: de16b6c0 ti: de048000 task.ti: de048000 PC is at strnlen+0xc/0x4c LR is at string+0x3c/0xf8 pc : [<c02c123c>] lr : [<c02c2d1c>] psr: a0000013 sp : de049e10 ip : c06efba0 fp : de6d2092 r10: bf01a260 r9 : ffffffff r8 : 74706164 r7 : 0000ffff r6 : ffffffff r5 : de6d209c r4 : 00000000 r3 : ff0a0004 r2 : 74706164 r1 : ffffffff r0 : 74706164 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c5387d Table: 9e530019 DAC: 00000015 Process cat (pid: 1635, stack limit = 0xde048240) Stack: (0xde049e10 to 0xde04a000) 9e00: de6d2092 00000002 bf01a25e de6d209c 9e20: de049e80 c02c438c 0000000a ff0a0004 ffffffff 00000000 00000000 de049e48 9e40: 00000000 2192df6d ff0a0004 ffffffff 00000000 de6d2092 de049ef8 bef3cc00 9e60: de6b0000 dc358000 de6d2000 00000000 00000003 c02c45a4 bf01790c bf01a254 9e80: 74706164 bf018698 00000000 de59c3c0 de048000 de049f80 00001000 bef3cc00 9ea0: 00000008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9ee0: 00000000 00000000 00000000 00000001 00000000 00000000 6669776d 20786569 9f00: 20302e31 2e343128 392e3636 3231702e 00202933 00000000 00000003 c0294898 9f20: 00000000 00000000 00000000 00000000 de59c3c0 c0107c04 de554000 de59c3c0 9f40: 00001000 bef3cc00 de049f80 bef3cc00 de049f80 00000000 00000003 c0108a00 9f60: de048000 de59c3c0 00000000 00000000 de59c3c0 00001000 bef3cc00 c0108b60 9f80: 00000000 00000000 00001000 bef3cc00 00000003 00000003 c0014128 de048000 9fa0: 00000000 c0013f80 00001000 bef3cc00 00000003 bef3cc00 00001000 00000000 9fc0: 00001000 bef3cc00 00000003 00000003 00000001 00000001 00000001 00000003 9fe0: 00000000 bef3cbdc 00011984 b6f1127c 60000010 00000003 18dbdd2c 7f7bfffd [<c02c123c>] (strnlen+0xc/0x4c) from [<c02c2d1c>] (string+0x3c/0xf8) [<c02c2d1c>] (string+0x3c/0xf8) from [<c02c438c>] (vsnprintf+0x1e8/0x3e8) [<c02c438c>] (vsnprintf+0x1e8/0x3e8) from [<c02c45a4>] (sprintf+0x18/0x24) [<c02c45a4>] (sprintf+0x18/0x24) from [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) from [<c0108a00>] (vfs_read+0xb0/0x144) [<c0108a00>] (vfs_read+0xb0/0x144) from [<c0108b60>] (SyS_read+0x44/0x70) [<c0108b60>] (SyS_read+0x44/0x70) from [<c0013f80>] (ret_fast_syscall+0x0/0x30) Code: e12fff1e e3510000 e1a02000 0a00000d (e5d03000) ---[ end trace ca98273dc605a04f ]--- The panic is caused by the mwifiex_info_read() routine assuming that there can only be four modes (0-3) which is an invalid assumption. For example, when testing P2P, the mode is '8' (P2P_CLIENT) so the code accesses data beyond the bounds of the bss_modes[] array which causes the panic. Fix this by updating bss_modes[] to support the current list of modes and adding a check to prevent the out-of-bounds access from occuring in the future when more modes are added. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12Bluetooth: btmrvl: support Marvell Bluetooth device SD8897Bing Zhao2-2/+30
The register offsets have been changed in SD8897 and newer chips. Define a new btmrvl_sdio_card_reg map for SD88xx. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12iwlwifi: fix rate control regressionMoshe Benji2-1/+2
Since driver does not use control.rates[0].count, we have never set that variable. But currently, after rate control API rewrite, this is required by mac80211. Otherwise legacy rates control does not work and we transmit always at 1Mbit/s on pre 11n networks. [same fix as for iwlegacy, thanks Stanislaw!] Signed-off-by: Moshe Benji <Moshe.Benji@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-12gianfar: Add backwards compatible Single Queue mode pollingClaudiu Manoil1-2/+49
Older Single Queue (SQ_SG_MODE) devices like TSEC (i.e. mpc83xx) don't feature the frame receive indication bits (RXF) in RSTAT. For these and for the rest of the SQ_SG_MODE devices, provide the appropiate polling routine that handles a single pair of Rx/Tx BD rings, removing the overhead incurred by the multiple queues/ multiple interrupt group devices (veTSEC/ eTSEC2.0 devices). So this is primarily a fix for the TSEC devices. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12sfc: Store port number in private data, not net_device::dev_idBen Hutchings2-2/+3
We should not use net_device::dev_id to indicate the port number, as this affects the way the local part of IPv6 addresses is normally generated. This field was intended for use where multiple devices may share a single assigned MAC address and need to have different IPv6 addresses. Siena's two ports each have their own MAC addresses. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12team: remove synchronize_rcu() called during port disableJiri Pirko3-18/+8
Check the unlikely case of team->en_port_count == 0 before modulo operation. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12team: use kfree_rcu instead of synchronize_rcu in team_port_devJiri Pirko1-2/+1
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12team: remove synchronize_rcu() called during queue override changeJiri Pirko1-16/+47
This patch removes synchronize_rcu() from function __team_queue_override_port_del(). That can be done because it is ok to do list_del_rcu() and list_add_tail_rcu() on the same list_head member without calling synchronize_rcu() in between. A bit of refactoring needed to be done because INIT_LIST_HEAD needed to be removed (to not kill the forward pointer) as well. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12net: can: Convert to use devm_ioremap_resourceTushar Behera1-2/+2
Commit 75096579c3ac ("lib: devres: Introduce devm_ioremap_resource()") introduced devm_ioremap_resource() and deprecated the use of devm_request_and_ioremap(). Signed-off-by: Tushar Behera <tushar.behera@linaro.org> CC: netdev@vger.kernel.org CC: linux-can@vger.kernel.org CC: Marc Kleine-Budde <mkl@pengutronix.de> CC: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-12net: emaclite: Convert to use devm_ioremap_resourceTushar Behera1-2/+4
Commit 75096579c3ac ("lib: devres: Introduce devm_ioremap_resource()") introduced devm_ioremap_resource() and deprecated the use of devm_request_and_ioremap(). Signed-off-by: Tushar Behera <tushar.behera@linaro.org> CC: netdev@vger.kernel.org CC: "David S. Miller" <davem@davemloft.net> CC: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-24 22:19:34 +0000