summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2012-03-27mtd: nand/fsmc: Initialize the badblockbits to 7Vipin Kumar1-0/+1
Ideally, the block should have 0xff written on the bad block position. Any value other than 0xff implies a bad block. In practical situations, there can be bit flips in the oob area as well which means that a block with 0x7f being read at bad block position may imply a bad block but it is infact only a bit flip in the bad block byte. To resolve this problem, the block is marked as good if number of high bits is greater than or equal to badblockbits (initialized to 7) Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: nand/fsmc: Flip the bit only if the error index is < 4096Vipin Kumar1-1/+1
ECC can correct up to 8 bits in 512 bytes data + 13 bytes ecc. This means that the algorithm can correct a max of 8 bits in 4200 bits ie the error indices can be from 0 to 4199. Of these 0 to 4095 are for data and 4096 to 4199 for ecc. The driver flips the bit only if the index is <= 4096. This is a bug since the data bits are only from 0 to 4095. This patch modifies the check as < 4096 Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: nand/fsmc: Read only 512 + 13 bytes for 8bit NAND devicesVipin Kumar1-1/+3
The ECC logic of FSMC works on 512 bytes data + 13 bytes ECC to generate error indices of up to 8 incorrect bits. The FSMC driver reads 14 instead of 13 oob bytes to accommodate for 16 bit device as well. Unfortunately, the internal ecc state machine gets corrupted for 8 bit devices reading 512 + 14 bytes of data resulting in error indices not getting reported. Fix this by reading 14 bytes only for 16 bit devices Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: nand/fsmc: Correct the multiline comment formatVipin Kumar1-4/+4
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: nand/fsmc: Remove default partition information from driverArmando Visconti1-58/+0
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: nand/fsmc: Pass partition information through platform dataVipin Kumar1-6/+7
This patch reimplements the passing of partition information through platform data. This was unintentionally deleted in commit 0d04eda1430e9a796214bee644b7e05d99cfe613 "mtd: fsmc_nand.c: use mtd_device_parse_register" Artem: fix gcc warning about passin 0 instead of NULL. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@kernel.org [3.2+] Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: phram: dot not crash when built-in and passing boot paramHervé Fache1-3/+30
This patch is based on Ville Herva's similar patch to block2mtd. Trying to pass a parameter through the kernel command line when built-in would crash the kernel, as phram_setup() was called so early that kmalloc() was not functional yet. This patch only saves the parameter string at the early boot stage, and parses it later when init_phram() is called. The same happens in both module and built-in cases. With this patch, I can boot with a statically-compiled phram, and mount a ext2 root fs from physical RAM, without the need for a initrd. This has been tested in built-in and module cases, with and without a parameter string. Artem: amended comments a bit Signed-off-by: Hervé Fache <h-fache@ti.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: gpmi: fix the wrong DMA command.Huang Shijie1-1/+2
The last DMA command of ECC read page is used to disable the BCH module. But the original code missed to set the pio[2] which is used to set the GPMI_HW_GPMI_ECCCTRL register. fix it now. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: flash drivers set ecc strengthMike Dunn31-1/+63
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the maximum number of bit errors that can be corrected in one writesize region. Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl, which is the maximum number of bit errors that can be corrected in one ecc step. Nand infrastructure code translates this to 'ecc_strength'. Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the driver for all other modes. Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: add ecc_strength fields to mtd structsMike Dunn2-0/+5
This adds 'ecc_strength' to struct mtd_info. This stores the maximum number of bit errors that can be corrected in one writesize region. For consistency with the nand code, 'strength' is similiarly added to struct nand_ecc_ctrl. This stores the maximum number of bit errors that can be corrected in one ecc step. Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: docg3 reduce read alignment burdenRobert Jarzmik1-8/+13
The read function was so far requiring the reads to be aligned on page boundaries, and be page length multiples in size. Relieve these constraints to ease the userspace ubifs programs runs, which read ubifs headers of 64 bytes. Artem: squashed a later fix from Robert Jarzmik into this patch. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Add power management with QoS requestBastian Hecht2-9/+45
Adds power management code with fine granularity. Every flash control command is enclosed by runtime_put()/get()s. To make sure that no overhead is generated by too frequent power state switches, a quality of service request is issued. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: do not use plain 0 as NULLArtem Bityutskiy41-85/+89
The first 3 arguments of 'mtd_device_parse_register()' are pointers, but many callers pass '0' instead of 'NULL'. Fix this globally. Thanks to coccinelle for making it easy to do with the following semantic patch: @@ expression mtd, types, parser_data, parts, nr_parts; @@ ( -mtd_device_parse_register(mtd, 0, parser_data, parts, nr_parts) +mtd_device_parse_register(mtd, NULL, parser_data, parts, nr_parts) | -mtd_device_parse_register(mtd, types, 0, parts, nr_parts) +mtd_device_parse_register(mtd, types, NULL, parts, nr_parts) | -mtd_device_parse_register(mtd, types, parser_data, 0, nr_parts) +mtd_device_parse_register(mtd, types, parser_data, NULL, nr_parts) ) Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: maps: sa1100-flash: Add reference counter to set_vpp()Paul Parsons1-1/+13
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch allows sa1100_set_vpp() calls to be nested by adding a reference counter. Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: maps: pcmciamtd: Add reference counter to set_vpp()Paul Parsons1-1/+12
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch allows pcmciamtd_set_vpp() calls to be nested by adding a reference counter. Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: maps: l440gx: Add reference counter to set_vpp()Paul Parsons1-5/+9
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch allows l440gx_set_vpp() calls to be nested by adding a reference counter. Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: maps: physmap: Add reference counter to set_vpp()Paul Parsons3-19/+26
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch allows physmap_set_vpp() calls to be nested by adding a reference counter. omap1_set_vpp() already used a reference counter. Since it is called from physmap_set_vpp(), omap1_set_vpp() can now be simplified. simtec_nor_vpp() already disabled hard interrupts. Since it is called from physmap_set_vpp(), simtec_nor_vpp() can now be simplified. Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: chips: cfi_cmdset_0002: Match ENABLE_VPP()/DISABLE_VPP() callsPaul Parsons1-2/+4
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch ensures that only those flash operations which call ENABLE_VPP() can then call DISABLE_VPP(). Other operations should never call DISABLE_VPP(). Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: chips: cfi_cmdset_0001: Match ENABLE_VPP()/DISABLE_VPP() callsPaul Parsons1-6/+9
This patch is part of a set which fixes unnecessary flash erase and write errors resulting from the MTD CFI driver turning off vpp while an erase is in progress. This patch ensures that only those flash operations which call ENABLE_VPP() can then call DISABLE_VPP(). Other operations should never call DISABLE_VPP(). Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: Support of 224-bytes OOB area lengthArmando Visconti1-0/+40
The current patch is required to support EVALSPEAR1340CPU Revision 2 where a new (ONFI compliant) MT29F16G08 NAND flash from Micron is present. This NAND flash device defines a OOB area which is 224 bytes long (oobsize). Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: Improve the fsmc_correct_data() routineArmando Visconti1-21/+17
This patch improves the error correction routine for bch8 - Loop only up to number of errors detected - Improve the error index calculation procedure Additionally, it also renames the "correct" routine to indicate that it is bch8 specific Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: fixed data abort inside change_bit()Armando Visconti1-1/+1
Since change_bit() requires a (unsigned int *) as second arg, the correct definition of err_idx[] array declared as local variable of fsmc_correct_data() is the following: u32 err_idx[8]; Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: Move ALE, CLE defines to their respective platformShiraz Hashim3-13/+7
Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are platform specific and were wrongly put in driver specific fsmc.h file. Move such defines to their respective platform. Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly from individual platform. Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: use ALE and CLE offsets from platform dataShiraz Hashim2-4/+10
ALE and CLE offsets can be different on different devices. Let devices pass these offsets to the fsmc driver through platform data. Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc_nand: ECC1 & ECC4 layout separated for different page sizesBhavna Yadav1-17/+159
ECC1 & ECC4 layout for NAND of different pages sizes for e.g. 512bytes, 2KiB, 4KiB and 8KiB are separated. Previously there existed one ECC4 layout for 2KiB & 4KiB page size due to which oob test module available in drivers/mtd/nand/test was failing. Signed-off-by: Bhavna Yadav <bhavna.yadav@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fsmc: Newly erased page read algorithm implementedVipin Kumar1-4/+52
A newly erased page contains ff in data as well as spare area. While reading an erased page, the read out ecc from spare area does not match the ecc generated by fsmc ecc hardware accelerator. This is because ecc of data ff ff is not ff ff. This leads to errors when file system erases and reads back the pages to ensure consistency. This patch adds a software workaround to ensure that the ecc check is not performed for erased pages. This problem is solved by checking the number of bits (in 512 byte data + 13 byte ecc) which are 0. If these number of bits are less than 8, the page is considered erased and correction algorithm is not tried on that page Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fix partition wrapper functionsMike Dunn1-27/+33
This patch reverts a change that may have been mistakenly included with the set of patches that introduced the new mtd api entry functions. Or perhaps I am mistaken :) The problem is in the partition wrapper functions, where the calls to the driver methods were replaced with calls to the new mtd api functions. This causes the api function to be called a second time, further down the call stack. This is not only unnecessary and redundant - because the sanity checking code and (more restrictive) bounds checks for the partition were done in the first call - but is potentially problematic and confusing. For example, the call stack for a call to mtd_read() on a partitioned device currently looks like this: mtd_read() gets struct mtd_info for the partition | +-> part_read() via the pointer assigned when the partition was created | +->mtd_read() this time gets struct mtd_info for the master | +->xyz_driver_read() via the pointer asigned by the driver It seems that this can cause a variety of problems. For example, if you want to add code to the api function that tests a value in mtd_info that is relevant only to the partition. Or (in my case) you want the driver to return a value that may be different from that returned by the mtd api function. This patch eliminates the second call to the mtd api function. It was tested on the docg4 nand driver with a subset of the api functions, but I inspected the rest and don't see any problems. Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: docg3 trivial renamingRobert Jarzmik1-1/+1
Change the name of the mtd so that it is simpler, and is easier to cope with by mtdparts. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27ARM: mach-shmobile: mackerel: Add the flash controller flctlBastian Hecht2-1/+74
Add board and clock setup code for the SH Mobile flctl controller. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Add FLHOLDCR registerBastian Hecht2-0/+15
Add a register used in new FLCTL hardware and a feature flag for it. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Use cached register value for FLCMNCRBastian Hecht2-15/+8
Instead of reading out the register, use a cached value. This will make way for a proper runtime power management implementation. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Implement NAND_CMD_RNDOUT commandBastian Hecht1-0/+16
Implements the command to seek and read in pages. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Expand the READID command to 8 bytesBastian Hecht1-3/+9
The nand base code wants to read out 8 bytes in the READID command. Reflect this in the driver code. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Reorder empty_fifo() callsBastian Hecht1-3/+2
Reorders the calls to make it a bit shorter and match the calling procedure displayed in the datasheet. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: sh_flctl: Expand FLCMNCR register bit fieldBastian Hecht1-0/+24
Add support for a new hardware generation. The meaning of some bits of the FLCMNCR register changed, so some new defines are added parallel to the existing ones to keep backward compatibility. The defines allow to choose an appropriate clocking scheme. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: Standardize JFFS_<LEVEL> usesJoe Perches3-34/+13
Use pr_<level> to prefix KBUILD_MODNAME via pr_fmt. Remove obfuscating defines and use constants in pr_<level> No need for a do {} while (0) for single statements. Form of JFFS_<LEVEL> output changes from "JFFS2 notice: " to "jffs2: notice: " Added pr_fmt to xattr.c Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: Use pr_fmt and remove jffs: from formatsJoe Perches23-38/+80
Use pr_fmt to prefix KBUILD_MODNAME to appropriate logging messages. Remove now unnecessary internal prefixes from formats. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: Convert printks to pr_<level>Joe Perches17-264/+342
Use the more current logging style. Coalesce formats, align arguments. Convert uses of embedded function names to %s, __func__. A couple of long line checkpatch errors I don't care about exist. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: Convert most D1/D2 macros to jffs2_dbgJoe Perches16-360/+504
D1 and D2 macros are mostly uses to emit debugging messages. Convert the logging uses of D1 & D2 to jffs2_dbg(level, fmt, ...) to be a bit more consistent style with the rest of the kernel. All jffs2_dbg output is now at KERN_DEBUG where some of the previous uses were emitted at various KERN_<LEVEL>s. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: mips: lantiq: reintroduce support for cmdline partitionsDaniel Schwierzeck1-1/+2
Since commit ca97dec2ab5c87e9fbdf7e882e1820004a3966fa the command line parsing of MTD partitions does not work anymore. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@kernel.org [3.2+] Acked-by: John Crispin <blogic@openwrt.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: change the location of the ONFI detected logHuang Shijie1-1/+1
Some strange nand chip(such as Hynix H27UBG8T2A) can pass the `ONFI` signature check. So the log can be printed out even it is not an ONFI nand indeed. Change this log to the end of the function. Print out the log only when we really detect an ONFI nand. Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Florian Fainelli <ffainelli@freebox.fr> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()Huang Shijie3-15/+46
[1] Background : The GPMI does ECC read page operation with a DMA chain consist of three DMA Command Structures. The middle one of the chain is used to enable the BCH, and read out the NAND page. The WAIT4END(wait for command end) is a comunication signal between the GPMI and MXS-DMA. [2] The current DMA code sets the WAIT4END bit at the last one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ | | set WAIT4END here This chain works fine in the mx23/mx28. [3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should be set not only at the last DMA Command Structure, but also at the middle one, such as: +-----+ +-----+ +-----+ | cmd | ------------> | cmd | ------------------> | cmd | +-----+ +-----+ +-----+ ^ ^ | | | | set WAIT4END here too set WAIT4END here If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state. In the next ECC write page operation, a DMA-timeout occurs. This has been catched in the MX6Q board. [4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(), and use the dma_ctrl_flags: --------------------------------------------------------- DMA_PREP_INTERRUPT : append a new DMA Command Structrue. DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure. --------------------------------------------------------- [5] changes to the relative drivers: <1> For mxs-mmc driver, just use the new flags, do not change any logic. <2> For gpmi-nand driver, and use the new flags to set the DMA chain, especially for ecc read page. Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mxs-dma : move the mxs dma.h to a more common placeHuang Shijie7-6/+6
Move the header to a more common place. The mxs dma engine is not only used in mx23/mx28, but also used in mx50/mx6q. It will also be used in the future chips. Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to store the Freescale's header files. change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver to the new header file. Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Acked-by: Chris Ball <cjb@laptop.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: make jffs2_initxattrs() staticNikola Pajkovsky1-2/+2
Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: fix 'Flash device refused suspend due to active operation' messageRussell King1-1/+1
While debugging on SA11x0, the following message was observed: "Flash device refused suspend due to active operation (state 20)" Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: gpmi: fix compiler warningHuang Shijie1-1/+0
The gpmi driver selects the MTD_CMDLINE_PARTS directly. But we should not select a visible symbol. Just remove the select. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: simplify return logic in do_map_probe()Uwe Kleine-König1-4/+1
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27sfc: mtd: Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffffShmulik Ladkani1-1/+1
As of bb0eb217, MTD_FAIL_ADDR_UNKNOWN should be used to indicate mtd erase failure not specific to any particular block. Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff when setting 'erase->fail_addr' in 'efx_mtd_erase()'. Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27jffs2: Fix typo in compr.cMasanari Iida1-1/+1
Correct spelling "modul" to "module" in fs/hffs2/compr.c Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27mtd: ixp4xx: oops in ixp4xx_flash_probeMarc Kleine-Budde1-1/+4
In commit "c797533 mtd: abstract last MTD partition parser argument" the third argument of "mtd_device_parse_register()" changed from start address of the MTD device to a pointer to a struct. The "ixp4xx_flash_probe()" function was not converted properly, causing an oops during boot. This patch fixes the problem by filling the needed information into a "struct mtd_part_parser_data" and passing it to "mtd_device_parse_register()". Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@kernel.org [3.2+] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-23 08:55:55 +0000