| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When registering more than one platform device, it is
useful to set the gpio chip label in the platform data.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no general support for 64-bit big endian accesses, so that is
left unsupported.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It fixes the issue in gpio-generic that commit fb14921 (gpio/mxc: add
missing initialization of basic_mmio_gpio shadow variables) manged to
fix in gpio-mxc driver, so that other platform specific drivers do not
suffer from the same problem over and over again.
Changes since v1:
* Turn the last parameter of bgpio_init() "bool big_endian" into
"unsigned long flags" and give those really quirky hardwares a
chance to tell that reg_set and reg_dir are unreadable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: Fix big-endian usage to explicitly set BBGPIOF_BIG_ENDIAN]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Building a kernel with hotplug disabled results in a link failure:
`bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
This is because of bgpio_remove() is exported. It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.
Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
include/linux/basic_mmio_gpio.h uses a spinlock_t without including any
of the spinlock headers resulting in this compiler warning.
include/linux/basic_mmio_gpio.h:51:2: error: expected specifier-qualifier-list before 'spinlock_t'
Explicitly include linux/spinlock_types.h to fix it.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail. Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.
Changes since v1:
- Register the gpio_chip in the platform device probe
1. https://lkml.org/lkml/2011/4/19/401
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
