summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc3
AgeCommit message (Collapse)AuthorFilesLines
2018-03-26usb: dwc3: gadget: never call ->complete() from ->ep_queue()Felipe Balbi1-18/+25
This is a requirement which has always existed but, somehow, wasn't reflected in the documentation and problems weren't found until now when Tuba Yavuz found a possible deadlock happening between dwc3 and f_hid. She described the situation as follows: spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire /* we our function has been disabled by host */ if (!hidg->req) { free_ep_req(hidg->in_ep, hidg->req); goto try_again; } [...] status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC); => [...] => usb_gadget_giveback_request => f_hidg_req_complete => spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire Note that this happens because dwc3 would call ->complete() on a failed usb_ep_queue() due to failed Start Transfer command. This is, anyway, a theoretical situation because dwc3 currently uses "No Response Update Transfer" command for Bulk and Interrupt endpoints. It's still good to make this case impossible to happen even if the "No Reponse Update Transfer" command is changed. Reported-by: Tuba Yavuz <tuba@ece.ufl.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-23Merge tag 'usb-for-v4.17' of ↵Greg Kroah-Hartman9-90/+839
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing Felipe writes: usb: changes for v4.17 merge window Quite a lot happened in this cycle, with a total of 95 non-merge commits. The most interesting parts are listed below: Synopsys has been adding better support for USB 3.1 to dwc3. The same series also sets g_mass_storage's max speed to SSP. Roger Quadros (TI) added support for dual-role using the OTG block available in some dwc3 implementations, this makes sure that AM437x can swap roles in runtime. We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to the work of Martin Blumenstingl. We also have a ton of changes in dwc2 (51% of all changes, in fact). The most interesting part there is the support for Hibernation (a Synopsys PM feature). Apart from these, we have our regular set of non-critical fixes all over the place.
2018-03-22usb: dwc3: core: Fix broken system suspend/resume on AM437xRoger Quadros1-0/+2
On TI's AM437x, the DWC3 controller looses state after a system suspend/resume. We are re-initializing the controller but we miss restoring the PRTCAP register. This causes USB host to break on AM437x after a system suspend/resume. Fix this by restoring the PRTCAP register on system resume. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Check controller type before setting speedThinh Nguyen1-1/+4
DWC_usb3 speed can only be set up to SuperSpeed. Limit the setting to SuperSpeed only should the value be higher. Otherwise, the controller will read an invalid speed value and set the device to an incorrect speed. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Dump LSP and BMU debug infoThinh Nguyen2-0/+10
Dump LSP and BMU debug info. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Check for ESS TX/RX threshold configThinh Nguyen2-0/+63
Check and configure TX/RX threshold for DWC_usb31. Update dwc3 structure with new fields to store these threshold configurations. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Add DWC_usb31 GTXTHRCFG reg fieldsThinh Nguyen1-0/+10
Add new GTXTHRCFG bit field macros for DWC_usb31. The GTXTHRCFG register fields for DWC_usb31 is as follows: +-------+--------------------------+-----------------------------------+ | BITS | Name | Description | +=======+==========================+===================================+ | 31:27 | reserved | | | 26 | UsbTxPktCntSel | Async ESS transmit packet | | | | threshold enable | | 25:21 | UsbTxPktCnt | Async ESS transmit packet | | | | threshold count | | 20:16 | UsbMaxTxBurstSize | Async ESS Max transmit burst size | | 15 | UsbTxThrNumPktSel_HS_Prd | HS high bandwidth periodic | | | | transmit packet threshold enable | | 14:13 | UsbTxThrNumPkt_HS_Prd | HS high bandwidth periodic | | | | transmit packet threshold count | | 12:11 | reserved | | | 10 | UsbTxThrNumPktSel_Prd | Periodic ESS transmit packet | | | | threshold enable | | 9:5 | UsbTxThrNumPkt_Prd | Periodic ESS transmit packet | | | | threshold count | | 4:0 | UsbMaxTxBurstSize_Prd | Max periodic ESS TX burst size | +-------+--------------------------+-----------------------------------+ Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: gadget: Check IP revision for GRXTHRCFGThinh Nguyen1-1/+5
DWC_usb31 controller has a different UsbRxPktCnt bit fields from GRXTHRCFG register. Check for DWC_usb31 IP revision to read the appropriate value. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Add DWC_usb31 GRXTHRCFG bit fieldsThinh Nguyen1-0/+10
Add new GRXTHRCFG bit field macros for DWC_usb31. The GRXTHRCFG register fields for DWC_usb31 is as follows: +-------+--------------------------+----------------------------------+ | BITS | Name | Description | +=======+==========================+==================================+ | 31:27 | reserved | | | 26 | UsbRxPktCntSel | Async ESS receive packet | | | | threshold enable | | 25:21 | UsbRxPktCnt | Async ESS receive packet | | | | threshold count | | 20:16 | UsbMaxRxBurstSize | Async ESS Max receive burst size | | 15 | UsbRxThrNumPktSel_HS_Prd | HS high bandwidth periodic | | | | receive packet threshold enable | | 14:13 | UsbRxThrNumPkt_HS_Prd | HS high bandwidth periodic | | | | receive packet threshold count | | 12:11 | reserved | | | 10 | UsbRxThrNumPktSel_Prd | Periodic ESS receive packet | | | | threshold enable | | 9:5 | UsbRxThrNumPkt_Prd | Periodic ESS receive packet | | | | threshold count | | 4:0 | UsbMaxRxBurstSize_Prd | Max periodic ESS RX burst size | +-------+--------------------------+----------------------------------+ Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Check IP revision for GTXFIFOSIZThinh Nguyen1-1/+4
DWC_usb31 controller has different GTXFIFOSIZE bit field for TXFDEF. Check for DWC_usb31 IP revision to read the appropriate bit fields. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fieldsThinh Nguyen1-0/+2
Update two GTXFIFOSIZ bit fields for the DWC_usb31 controller. TXFDEP is a 15-bit value instead of 16-bit value, and bit 15 is TXFRAMNUM. The GTXFIFOSIZ register for DWC_usb31 is as follows: +-------+-----------+----------------------------------+ | BITS | Name | Description | +=======+===========+==================================+ | 31:16 | TXFSTADDR | Transmit FIFOn RAM Start Address | | 15 | TXFRAMNUM | Asynchronous/Periodic TXFIFO | | 14:0 | TXFDEP | TXFIFO Depth | +-------+-----------+----------------------------------+ Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Add SoftReset PHY synchonization delayThinh Nguyen1-1/+12
From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST bit is cleared, we must wait at least 50ms before accessing the PHY domain (synchronization delay). Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: pci: Properly cleanup resourceThinh Nguyen1-1/+1
Platform device is allocated before adding resources. Make sure to properly cleanup on error case. Cc: <stable@vger.kernel.org> Fixes: f1c7e7108109 ("usb: dwc3: convert to pcim_enable_device()") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22usb: dwc3: Makefile: fix link error on randconfigFelipe Balbi1-1/+1
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to link due to missing trace events. Fix this by using the correct Kconfig symbol on Makefile. Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-19usb: dwc3: ep0: remove redundant assignmentHeinrich Schuchardt1-1/+1
In dwc3_request *r = NULL; r = A; the first assignment has no effect. Remove it. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: Prevent indefinite sleep in _dwc3_set_mode during suspend/resumeRoger Quadros1-3/+20
In the following test we get stuck by sleeping forever in _dwc3_set_mode() after which dual-role switching doesn't work. On dra7-evm's dual-role port, - Load g_zero gadget driver and enumerate to host - suspend to mem - disconnect USB cable to host and connect otg cable with Pen drive in it. - resume system - we sleep indefinitely in _dwc3_set_mode due to. dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()-> dwc3_gadget_stop()->wait_event_lock_irq() To fix this instead of waiting indefinitely with wait_event_lock_irq() we use wait_event_interruptible_lock_irq_timeout() and print and error message if there was a timeout. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: add dual role support using OTG blockRoger Quadros3-28/+557
This is useful on platforms (e.g. TI AM437x) that don't have ID available on a GPIO but do have the OTG block. We can obtain the ID state via the OTG block and use it for dual-role switching. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: prevent setting PRTCAP to OTG from debugfsRoger Quadros1-0/+3
We don't support PRTCAP == OTG yet, so prevent user from setting it via debugfs. Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: core.h: add some register definitionsRoger Quadros1-0/+82
Add OTG and GHWPARAMS6 register definitions Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG SoCsMartin Blumenstingl1-0/+8
Amlogic Meson GXL and AXG SoCs come with a (host-only) dwc3 USB controller. To use this controller a clock has to be enabled and a reset line has to be pulsed. Enabling the clock works identical to other SoCs. However, the reset line has to be pulsed (using reset_control_reset) instead of using a level reset (reset_control_{assert,deassert}). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13usb: dwc3: of-simple: add support for shared and pulsed reset linesMartin Blumenstingl1-6/+17
Some SoCs (such as Amlogic Meson GXL for example) share the reset line with other components (in case of the Meson GXL example there's a shared reset line between the USB2 PHYs, USB3 PHYs and the dwc3 controller). Additionally SoC implementations may prefer a reset pulse over level resets. For now this falls back to the old defaults, which are: - reset lines are exclusive - level resets are being used Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Yixun Lan <yixun.lan@amlogic.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-08usb: dwc3: debugfs: Re-use DEFINE_SHOW_ATTRIBUTE() macroFelipe Balbi1-49/+30
...instead of open coding file operations followed by custom ->open() callbacks per each attribute. Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-28usb: dwc3: Fix lock-up on ID change during system suspend/resumeRoger Quadros1-1/+1
To reproduce the lock up do the following - connect otg host adapter and a USB device to the dual-role port so that it is in host mode. - suspend to mem. - disconnect otg adapter. - resume the system. If we call dwc3_host_exit() before tasks are thawed xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call. To work around this we queue the _dwc3_set_mode() work on the system_freezable_wq. Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly") Cc: <stable@vger.kernel.org> # v4.12+ Suggested-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-15usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during ↵Roger Quadros2-11/+41
suspend/resume In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init() must be doene before dwc3_core_get_phy(). commit 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys") broke this. The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should be called only once during the life cycle of the driver. However, as dwc3_core_init() is called during system suspend/resume it will result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init() which is wrong. Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup() into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that dwc3_core_ulpi_init() is called only once from dwc3_core_init(). Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from dwc3_core_init(). Fixes: 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys") Fixes: f54edb539c11 ("usb: dwc3: core: initialize ULPI before trying to get the PHY") Cc: linux-stable <stable@vger.kernel.org> # >= v4.13 Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: Fix GDBGFIFOSPACE_TYPE valuesThinh Nguyen1-7/+9
The FIFO/Queue type values are incorrect. Correct them according to DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25). Additionally, this patch includes ProtocolStatusQ and AuxEventQ types. Fixes: cf6d867d3b57 ("usb: dwc3: core: add fifo space helper") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: omap: don't miss events during suspend/resumeRoger Quadros1-0/+16
The USB cable state can change during suspend/resume so be sure to check and update the extcon state. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: core: Power-off core/PHYs on system_suspend in host modeManu Gautam1-14/+22
Commit 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume") updated suspend/resume routines to not power_off and reinit PHYs/core for host mode. It broke platforms that rely on DWC3 core to power_off PHYs to enter low power state on system suspend. Perform dwc3_core_exit/init only during host mode system_suspend/ resume to addresses power regression from above mentioned patch and also allow USB session to stay connected across runtime_suspend/resume in host mode. While at it also replace existing checks for HOST only dr_mode with current_dr_role to have similar core driver behavior for both Host-only and DRD+Host configurations. Fixes: 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume") Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: Undo PHY init if soft reset failsBrian Norris1-0/+3
In this function, we init the USB2 and USB3 PHYs, but if soft reset times out, we don't unwind this. Noticed by inspection. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: ep0: Reset TRB counter for ep0 INThinh Nguyen1-1/+6
DWC3 tracks TRB counter for each ep0 direction separately. In control read transfer completion handler, the driver needs to reset the TRB enqueue counter for ep0 IN direction. Currently the driver only resets the TRB counter for control OUT endpoint. Check for the data direction and properly reset the TRB counter from correct control endpoint. Cc: stable@vger.kernel.org Fixes: c2da2ff00606 ("usb: dwc3: ep0: don't use ep0in for transfers") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: gadget: Set maxpacket size for ep0 INThinh Nguyen1-0/+2
There are 2 control endpoint structures for DWC3. However, the driver only updates the OUT direction control endpoint structure during ConnectDone event. DWC3 driver needs to update the endpoint max packet size for control IN endpoint as well. If the max packet size is not properly set, then the driver will incorrectly calculate the data transfer size and fail to send ZLP for HS/FS 3-stage control read transfer. The fix is simply to update the max packet size for the ep0 IN direction during ConnectDone event. Cc: stable@vger.kernel.org Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12usb: dwc3: of-simple: fix oops by unbalanced clk disable callEnric Balletbo i Serra1-0/+1
dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf31 ("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought and oops when unbind the device due this sequence: dwc3_of_simple_remove -> clk_disable ... -> pm_runtime_put_sync -> dwc3_of_simple_runtime_suspend -> clk_disable (again) This double call to clk_core_disable causes a kernel oops like this: WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80 CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44 Hardware name: Google Kevin (DT) pstate: 80000085 (Nzcv daIf -PAN -UAO) pc : clk_core_disable+0x78/0x80 lr : clk_core_disable_lock+0x20/0x38 sp : ffff00000bbf3a90 ... Call trace: clk_core_disable+0x78/0x80 clk_disable+0x1c/0x30 dwc3_of_simple_runtime_suspend+0x30/0x50 pm_generic_runtime_suspend+0x28/0x40 This patch fixes the unbalanced clk disable call by setting the num_clocks variable to zero once the clocks were disabled. Fixes: a0d8c4cfdf31 ("usb: dwc3: of-simple: set dev_pm_ops") Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-01-08Merge tag 'phy-for-4.16' of ↵Greg Kroah-Hartman1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next Kishon writes: phy: for 4.16 *) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3 *) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working *) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled to save power *) Fix in Broadcom USB PHY to prevent abort in DRD mode *) Fix in Broadcom USB PHY to use the correct dt properties *) Fix in Mediatek PHY to detect device connection *) Make getting resource optional for Mediatek V1 TPHY *) Cleanup in Mediatek PHY Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-01-08Merge tag 'usb-for-v4.16' of ↵Greg Kroah-Hartman6-11/+22
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: changes for v4.16 merge window Not many changes here, the most important being an improvement for TI's AM57xx and DRA7xx devices which allows them to disable a metastability workaround in situations where we know what's going on. Other than that, we have a set of changes on Renesas UDC to make the code a little easier to read and maintain while also better supporting extcon framework. The u_serial adaptation layer learned to use kfifo instead of cooking its own FIFO implementation. DWC3 learned to decode a few more USB requests on the trace output.
2017-12-29phy: exynos5-usbdrd: Calibrate LOS levels for exynos5420/5800Vivek Gautam1-0/+2
Adding phy calibration sequence for USB 3.0 DRD PHY present on Exynos5420/5800 systems. This calibration facilitates setting certain PHY parameters viz. the Loss-of-Signal (LOS) Detector Threshold Level, as well as Tx-Vboost-Level for Super-Speed operations. Additionally we also set proper time to wait for RxDetect measurement, for desired PHY reference clock, so as to solve issue with enumeration of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive on the controller. We are using CR_port for this purpose to send required data to override the LOS values. On testing with USB 3.0 devices on USB 3.0 port present on SMDK5420, and peach-pit boards should see following message: usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd and without this patch, should see below shown message: usb 1-1: new high-speed USB device number 2 using xhci-hcd [Also removed unnecessary extra lines in the register macro definitions] Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> [adapted to use phy_calibrate as entry point] Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-12-11usb: dwc3: Allow disabling of metastability workaroundRoger Quadros3-2/+10
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble with the metastability workaround as it supports only a High-Speed PHY and the PHY can enter into an Erratic state [1] when the controller is set in SuperSpeed mode as part of the metastability workaround. This causes upto 2 seconds delay in enumeration on DRA7's USB2 instance in gadget mode. If these platforms can be better off without the workaround, provide a device tree property to suggest that so the workaround is avoided. [1] Device mode enumeration trace showing PHY Erratic Error. irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0] irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0] irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0] Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: Make sparse a bit happierVincent Pelletier1-2/+2
Fixes the following warnings: drivers/usb/dwc3/io.h:43:31: warning: incorrect type in argument 1 (different address spaces) drivers/usb/dwc3/io.h:43:31: expected void *base drivers/usb/dwc3/io.h:43:31: got void [noderef] <asn:2>* drivers/usb/dwc3/io.h:62:32: warning: incorrect type in argument 1 (different address spaces) drivers/usb/dwc3/io.h:62:32: expected void *base drivers/usb/dwc3/io.h:62:32: got void [noderef] <asn:2>* This fixes the noisiest ones as they get emitted multiple times. A few warnings remain, for which the proper fix is less clear. No behaviour change is expected. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: ep0: use gadget->isoch_delay for isoch_delay valueFelipe Balbi2-7/+1
Instead of keeping our own isoch_delay, let's make use of the newly introduced isoch_delay member in struct usb_gadget. The benefit here is that we would be using a generic "API" which other UDCs can use, resulting in a common setup for gadget drivers who may be interested in Isoch Delay value. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: debug: decode a few more featuresFelipe Balbi1-0/+9
We were missing U1, U2 and LTM Enable features. Let's decode them. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3Manu Gautam1-1/+1
For isochronous endpoints with ep->mult less than 3, PCM1 value of trb->size in set incorrectly. For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is set to -2. This is because the initial mult is set to ep->mult - 1 instead of 2. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: of-simple: set dev_pm_opsMasahiro Yamada1-0/+1
dwc3_of_simple_dev_pm_ops has never been used since the initial support by commit 16adc674d0d6 ("usb: dwc3: add generic OF glue layer"). I guess it just missed to set .pm struct member. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: of-simple: fix missing clk_disable_unprepareAndreas Platschek1-1/+3
If of_clk_get() fails, the clean-up of already initialized clocks should be the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare() for each clock should be called before the clk_put(). Found by Linux Driver Verification project (linuxtesting.org). Fixes: 16adc674d0d6 ("usb: dwc3: ep0: fix setup_packet_pending initialization") Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11usb: dwc3: gadget: Wait longer for controller to end command processingVincent Pelletier1-1/+1
DWC3_DEPCMD_ENDTRANSFER has been witnessed to require around 600 iterations before controller would become idle again after unplugging the USB cable with AIO reads submitted. Bump timeout from 500 iterations to 1000 so dwc3_stop_active_transfer does not receive -ETIMEDOUT and does not WARN: [ 81.326273] ------------[ cut here ]------------ [ 81.335341] WARNING: CPU: 0 PID: 1874 at drivers/usb/dwc3/gadget.c:2627 dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3] [ 81.347094] Modules linked in: usb_f_fs libcomposite configfs bnep btsdio bluetooth ecdh_generic brcmfmac brcmutil dwc3 intel_powerclamp coretemp ulpi kvm_intel udc_core kvm irqbypass crc32_pclmul crc32c_intel pcbc dwc3_pci aesni_intel aes_i586 crypto_simd cryptd ehci_pci ehci_hcd basincove_gpadc industrialio gpio_keys usbcore usb_common [ 81.378142] CPU: 0 PID: 1874 Comm: irq/34-dwc3 Not tainted 4.14.0-edison+ #119 [ 81.385545] Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48 [ 81.394548] task: f5b1be00 task.stack: f420a000 [ 81.399219] EIP: dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3] [ 81.406086] EFLAGS: 00010086 CPU: 0 [ 81.409672] EAX: 0000001f EBX: f5729800 ECX: c132a2a2 EDX: 00000000 [ 81.416096] ESI: f4054014 EDI: f41cf400 EBP: f420be10 ESP: f420bdf4 [ 81.422521] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 [ 81.428061] CR0: 80050033 CR2: b7a3f000 CR3: 01d94000 CR4: 001006d0 [ 81.434483] Call Trace: [ 81.437063] __dwc3_gadget_ep_disable+0xa3/0x2b0 [dwc3] [ 81.442438] ? _raw_spin_lock_irqsave+0x32/0x40 [ 81.447135] dwc3_gadget_ep_disable+0xbf/0xe0 [dwc3] [ 81.452269] usb_ep_disable+0x1c/0xd0 [udc_core] [ 81.457048] ffs_func_eps_disable.isra.15+0x3b/0x90 [usb_f_fs] [ 81.463070] ffs_func_set_alt+0x7d/0x310 [usb_f_fs] [ 81.468132] ffs_func_disable+0x14/0x20 [usb_f_fs] [ 81.473075] reset_config+0x5b/0x90 [libcomposite] [ 81.478023] composite_disconnect+0x2b/0x50 [libcomposite] [ 81.483685] dwc3_disconnect_gadget+0x39/0x50 [dwc3] [ 81.488808] dwc3_gadget_disconnect_interrupt+0x21b/0x250 [dwc3] [ 81.495014] dwc3_thread_interrupt+0x2a8/0xf70 [dwc3] [ 81.500219] ? __schedule+0x78c/0x7e0 [ 81.504027] irq_thread_fn+0x18/0x30 [ 81.507715] ? irq_thread+0xb7/0x180 [ 81.511400] irq_thread+0x111/0x180 [ 81.515000] ? irq_finalize_oneshot+0xe0/0xe0 [ 81.519490] ? wake_threads_waitq+0x30/0x30 [ 81.523806] kthread+0x107/0x110 [ 81.527131] ? disable_percpu_irq+0x50/0x50 [ 81.531439] ? kthread_stop+0x150/0x150 [ 81.535397] ret_from_fork+0x19/0x24 [ 81.539136] Code: 89 d8 c7 45 ec 00 00 00 00 c7 45 f0 00 00 00 00 c7 45 f4 00 00 00 00 e8 56 ef ff ff 85 c0 74 12 50 68 b9 1c 14 f8 e8 64 0f f7 c8 <0f> ff 58 5a 8d 76 00 8b 83 98 00 00 00 c6 83 a0 00 00 00 00 83 [ 81.559295] ---[ end trace f3133eec81a473b8 ]--- Number of iterations measured on 4 consecutive unplugs: [ 1088.799777] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 605 times [ 1222.024986] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 580 times [ 1317.590452] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 598 times [ 1453.218314] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 594 times Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-11-13Merge tag 'usb-4.15-rc1' of ↵Linus Torvalds19-268/+122
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver updates for 4.15-rc1. There is the usual amount of gadget and xhci driver updates, along with phy and chipidea enhancements. There's also a lot of SPDX tags and license boilerplate cleanups as well, which provide some churn in the diffstat. Other major thing is the typec code that moved out of staging and into the "real" part of the drivers/usb/ tree, which was nice to see happen. All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits) usb: gadget: f_fs: Fix use-after-free in ffs_free_inst USB: usbfs: compute urb->actual_length for isochronous usb: core: message: remember to reset 'ret' to 0 when necessary USB: typec: Remove remaining redundant license text USB: typec: add SPDX identifiers to some files USB: renesas_usbhs: rcar?.h: add SPDX tags USB: chipidea: ci_hdrc_tegra.c: add SPDX line USB: host: xhci-debugfs: add SPDX lines USB: add SPDX identifiers to all remaining Makefiles usb: host: isp1362-hcd: remove a couple of redundant assignments USB: adutux: remove redundant variable minor usb: core: add a new usb_get_ptm_status() helper usb: core: add a 'type' parameter to usb_get_status() usb: core: introduce a new usb_get_std_status() helper usb: core: rename usb_get_status() 'type' argument to 'recip' usb: core: add Status Type definitions USB: gadget: Remove redundant license text USB: gadget: function: Remove redundant license text USB: gadget: udc: Remove redundant license text USB: gadget: legacy: Remove redundant license text ...
2017-11-07USB: dwc3: Remove redundant license textGreg Kroah-Hartman19-168/+0
Now that the SPDX tag is in all USB files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04USB: add SPDX identifiers to all remaining files in drivers/usb/Greg Kroah-Hartman19-0/+19
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/usb/ and include/linux/usb* files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-24usb: dwc3: core: Notify current USB mode to USB3 PHY as wellManu Gautam1-9/+8
Driver currently notifies only USB2 PHY on USB mode change. Extend this to USB3 PHY so that PHY drivers based on the mode can release system resources - clocks, regulators etc. Additionally Qualcomm QMP and QUSB2 PHY drivers need to override VBUS signal in PHY wrapper in device mode as USB VBUS line is not connected to PHYs. Also, remove NULL checks for PHY when calling phy_set_mode as PHY ops already check this. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-24usb: dwc3: pci: Runtime resume child device from wqManu Gautam2-3/+27
Driver currently resumes and increments pm usage_count of its child device (dwc3 main) from its runtime_resume handler. This requires dwc3 runtime_resume to perform pm_runtime_put to decrement the pm usage_count. However runtime_put from dwc3 happens for non pci drivers (e.g. dwc3-if-simple.c) as well which results in dwc3 pm usage_count becoming negative after couple of runtime suspend resume iterations. Fix this by performing runtime_get/put from dwc3-pci driver only using workqueue. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-24usb: dwc3: Don't reinitialize core during host bus-suspend/resumeManu Gautam1-23/+20
Driver powers-off PHYs and reinitializes DWC3 core and gadget on resume. While this works fine for gadget mode but in host mode there is not re-initialization of host stack. Also, resetting bus as part of bus_suspend/resume is not correct which could affect (or disconnect) connected devices. Fix this by not reinitializing core on suspend/resume in host mode for HOST only and OTG/drd configurations. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19usb: dwc3: of-simple: Add support to get resets for the deviceVivek Gautam1-2/+25
Add support to get a list of resets available for the device. These resets must be kept de-asserted until the device is in use. Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> [p.zabel@pengutronix.de: switch to hidden reset control array] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 13:03:54 +0000