| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Ensure HWMON devices are registered with valid names
- Fix device wakeup code
Drivers:
- bq25890_charger: Add BQ25895 support
- axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
- sc27xx: improve battery calibration
- misc small fixes all over drivers"
* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: supply: cpcap-charger: Enable vbus boost voltage
power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
power: supply: sc27xx: Optimize the battery capacity calibration
power: supply: sc27xx: Make sure the alarm capacity is larger than 0
power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
power: supply: sc27xx: Fix conditon to enable the FGU interrupt
power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
power: supply: max77650: add MODULE_ALIAS()
power: supply: isp1704: remove redundant assignment to variable ret
power: supply: bq25890_charger: Add the BQ25895 part
power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
power: supply: sc27xx: Introduce local variable 'struct device *dev'
power: reset: reboot-mode: Fix author email format
power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
power: supply: max17042_battery: Fix a typo in function names
power: reset: gpio-restart: Fix typo when gpio reset is not found
power: supply: Init device wakeup after device_add()
power: supply: ab8500_charger: Mark expected switch fall-through
power: supply: sbs-battery: only return health when battery present
MAINTAINERS: N900: Remove isp1704_charger.h record
...
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC / MFD Migration:
- Move cros_ec core driver from mfd into chrome platform.
Wilco EC:
- Add batt_ppid_info command to Wilco telemetry driver.
CrOS EC:
- cros_ec_rpmsg : Add support to inform EC of suspend/resume status
- cros_ec_rpmsg : Fix race condition on probe failed
- cros_ec_chardev : Add a poll handler to receive MKBP events
Misc:
- bugfixes in cros_usbpd_logger and cros_ec_ishtp"
* tag 'tag-chrome-platform-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_usbpd_logger: null check create_singlethread_workqueue
platform/chrome: cros_ec_chardev: Add a poll handler to receive MKBP events
platform/chrome: cros_ec_rpmsg: Fix race with host command when probe failed
platform/chrome: chromeos_tbmc: Report wake events
mfd: cros_ec: Use mfd_add_hotplug_devices() helper
mfd: cros_ec: Add convenience struct to define autodetectable CrOS EC subdevices
mfd: cros_ec: Add convenience struct to define dedicated CrOS EC MCUs
mfd: cros_ec: Use kzalloc and cros_ec_cmd_xfer_status helper
mfd / platform: cros_ec: Reorganize platform and mfd includes
mfd / platform: cros_ec: Rename config to a better name
mfd: cros_ec: Switch to use the new cros-ec-chardev driver
mfd / platform: cros_ec: Miscellaneous character device to talk with the EC
mfd / platform: cros_ec: Move cros-ec core driver out from MFD
mfd / platform: cros_ec: Handle chained ECs as platform devices
platform/chrome: cros_ec_rpmsg: Add host command AP sleep state support
platform/chrome: chromeos_laptop: drop checks of NULL-safe functions
platform/chrome: wilco_ec: Add batt_ppid_info command to telemetry driver
|
|
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add the 'POWER_SUPPLY_PROP_CALIBRATE' attribute to allow chareger manager
to calibrate the battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This patch factors out the capacity calibration into one single function
to calibrate the battery capacity, and adding more abnormal cases to
calibrate the capacity when the OCV value is not matchable with current
capacity.
Moreover we also allow to calibrate the capacity when charger magager
tries to get current capacity to make sure we give a correct capacity
for userspace.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We must make sure the alarm capacity is larger than 0, to help to
calibrate the low battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Spreadtrum fuel gauge will multiply by 2 for counting the coulomb
counter to improve the accuracy, which means the value saved in fuel
gauge is: coulomb counter * 2 * 1000ma_adc. Thus fix the conversion
formular to improve the accuracy of calculating the battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We should allow to enable FGU interrupt to adjust the battery capacity,
when charging status is POWER_SUPPLY_STATUS_DISCHARGING.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute to provide the battery's
design capacity for charger manager to calculate the charging counter.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Define a MODULE_ALIAS() in the charger sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The variable ret is being assigned with a value that is never
read and it is being updated later with a new value. The
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The BQ25895 is almost identical to the BQ25890.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
with devm_add_action_or_reset()
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Introduce local variable 'struct device *dev' and use it instead of
dereferencing it repeatly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Closing angle bracket was missing.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
'bup_vch_range'
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/power/supply/ab8500_charger.c:
In function ab8500_charger_init_hw_registers:
drivers/power/supply/ab8500_charger.c:3013:24: warning:
variable vbup33_vrtcn set but not used [-Wunused-but-set-variable]
drivers/power/supply/ab8500_charger.c:3013:5: warning:
variable bup_vch_range set but not used [-Wunused-but-set-variable]
Fixes: 4c4268dc97c4 ("power: supply: ab8500: Drop AB8540/9540 support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
It is likely that 'max10742_[un]lock_model()' functions should be
'max17042_[un]lock_model()'
(0 and 7 switched in 10742)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Trivial patch which just corrects error message.
Fixes: 371bb20d6927 ("power: Add simple gpio-restart driver")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We may want to use the device pointer in device_init_wakeup() with
functions that expect the device to already be added with device_add().
For example, if we were to link the device initializing wakeup to
something in sysfs such as a class for wakeups we'll run into an error.
It looks like this code was written with the assumption that the device
would be added before initializing wakeup due to the order of operations
in power_supply_unregister().
Let's change the order of operations so we don't run into problems here.
Fixes: 948dcf966228 ("power_supply: Prevent suspend until power supply events are processed")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tri Vo <trong@android.com>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: allmodconfig arm):
drivers/power/supply/ab8500_charger.c:738:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
when the battery is set to sbs-mode and no gpio detection is enabled
"health" is always returning a value even when the battery is not present.
All other fields return "not present".
This leads to a scenario where the driver is constantly switching between
"present" and "not present" state. This generates a lot of constant
traffic on the i2c.
This commit changes the response of "health" to an error when the battery
is not responding leading to a consistent "not present" state.
Fixes: 76b16f4cdfb8 ("power: supply: sbs-battery: don't assume MANUFACTURER_DATA formats")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Nosthoff <committed@heine.so>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
the type flag is stored in the chip->flags field not in the
client->flags field. This currently leads to never using the ti
specific health function as client->flags doesn't use that bit.
So it's always falling back to the general one.
Fixes: 76b16f4cdfb8 ("power: supply: sbs-battery: don't assume MANUFACTURER_DATA formats")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Nosthoff <committed@heine.so>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Minix Neo Z83-4 is another mini PC using the AXP288 PMIC where the
EFI code does not disable the charger part of the PMIC causing us to report
battery readings (of always 100%) to userspace even though there is no
battery in this wall-outlet powered device.
Add it to the blacklist to avoid the bogus battery status reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The blacklist is getting big enough that it is good to have some sort
of fixed order for it, sort it alphabetically.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
With the introduction of the HWMON compatibility layer to the power
supply framework in Linux 5.3, all power supply devices' names can be
used directly to create HWMON devices with the same names.
But HWMON has rules on allowable names that are different from those
used in the power supply framework. The dash character is forbidden, as
it is used by the libsensors library in userspace as a separator,
whereas this character is used in the device names in more than half of
the existing power supply drivers. This last case is consistent with the
typical naming usage with MFD and Device Tree.
This leads to warnings in the kernel log, with the format:
power_supply gpio-charger: hwmon: \
'gpio-charger' is not a valid name attribute, please fix
Add a protection to power_supply_add_hwmon_sysfs() that replaces any
dash in the device name with an underscore when registering with the
HWMON framework. Other forbidden characters (star, slash, space, tab,
newline) are not replaced, as they are not in common use.
Fixes: e67d4dfc9ff1 ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: allmodconfig arm):
drivers/power/supply/ab8500_charger.c: In function ‘ab8500_charger_max_usb_curr’:
drivers/power/supply/ab8500_charger.c:738:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (di->vbus_detected) {
^
drivers/power/supply/ab8500_charger.c:745:2: note: here
case USB_STAT_HM_IDGND:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
It has been replaced with the more mature ingenic-battery driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- add HWMON compat layer
- new properties:
- input power limit
- input voltage limit
Drivers:
- qcom-pon: add gen2 support
- new driver for storing reboot move in NVMEM
- new driver for Wilco EC charger configuration
- simplify getting the adapter of a client"
* tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: nvmem-reboot-mode: add CONFIG_OF dependency
power_supply: wilco_ec: Add charging config driver
power: supply: cros: allow to set input voltage and current limit
power: supply: add input power and voltage limit properties
power: supply: fix semicolon.cocci warnings
power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface
dt-bindings: power: reset: add document for NVMEM based reboot-mode
reset: qcom-pon: Add support for gen2 pon
dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line
power: supply: Add HWMON compatibility layer
power: supply: sbs-manager: simplify getting the adapter of a client
power: supply: rt9455_charger: simplify getting the adapter of a client
power: supply: rt5033_battery: simplify getting the adapter of a client
power: supply: max17042_battery: simplify getting the adapter of a client
power: supply: max17040_battery: simplify getting the adapter of a client
power: supply: max14656_charger_detector: simplify getting the adapter of a client
power: supply: bq25890_charger: simplify getting the adapter of a client
power: supply: bq24257_charger: simplify getting the adapter of a client
power: supply: bq24190_charger: simplify getting the adapter of a client
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration changes:
- Evaluate PCI Boot Configuration _DSM to learn if firmware wants us
to preserve its resource assignments (Benjamin Herrenschmidt)
- Simplify resource distribution (Nicholas Johnson)
- Decode 32 GT/s link speed (Gustavo Pimentel)
Virtualization:
- Fix incorrect caching of VF config space size (Alex Williamson)
- Fix VF driver probing sysfs knobs (Alex Williamson)
Peer-to-peer DMA:
- Fix dma_virt_ops check (Logan Gunthorpe)
Altera host bridge driver:
- Allow building as module (Ley Foon Tan)
Armada 8K host bridge driver:
- add PHYs support (Miquel Raynal)
DesignWare host bridge driver:
- Export APIs to support removable loadable module (Vidya Sagar)
- Enable Relaxed Ordering erratum workaround only on Tegra20 &
Tegra30 (Vidya Sagar)
Hyper-V host bridge driver:
- Fix use-after-free in eject (Dexuan Cui)
Mobiveil host bridge driver:
- Clean up and fix many issues, including non-identify mapped
windows, 64-bit windows, multi-MSI, class code, INTx clearing (Hou
Zhiqiang)
Qualcomm host bridge driver:
- Use clk bulk API for 2.4.0 controllers (Bjorn Andersson)
- Add QCS404 support (Bjorn Andersson)
- Assert PERST for at least 100ms (Niklas Cassel)
R-Car host bridge driver:
- Add r8a774a1 DT support (Biju Das)
Tegra host bridge driver:
- Add support for Gen2, opportunistic UpdateFC and ACK (PCIe protocol
details) AER, GPIO-based PERST# (Manikanta Maddireddy)
- Fix many issues, including power-on failure cases, interrupt
masking in suspend, UPHY settings, AFI dynamic clock gating,
pending DLL transactions (Manikanta Maddireddy)
Xilinx host bridge driver:
- Fix NWL Multi-MSI programming (Bharat Kumar Gogada)
Endpoint support:
- Fix 64bit BAR support (Alan Mikhak)
- Fix pcitest build issues (Alan Mikhak, Andy Shevchenko)
Bug fixes:
- Fix NVIDIA GPU multi-function power dependencies (Abhishek Sahu)
- Fix NVIDIA GPU HDA enablement issue (Lukas Wunner)
- Ignore lockdep for sysfs "remove" (Marek Vasut)
Misc:
- Convert docs to reST (Changbin Du, Mauro Carvalho Chehab)"
* tag 'pci-v5.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (107 commits)
PCI: Enable NVIDIA HDA controllers
tools: PCI: Fix installation when `make tools/pci_install`
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: Fix typos and whitespace errors
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
"Gathered a bunch of x86 platform driver changes. It's rather big,
since includes two big refactors and completely new driver:
- ASUS WMI driver got a big refactoring in order to support the TUF
Gaming laptops. Besides that, the regression with backlight being
permanently off on various EeePC laptops has been fixed.
- Accelerometer on HP ProBook 450 G0 shows wrong measurements due to
X axis being inverted. This has been fixed.
- Intel PMC core driver has been extended to be ACPI enumerated if
the DSDT provides device with _HID "INT33A1". This allows to
convert the driver to be pure platform and support new hardware
purely based on ACPI DSDT.
- From now on the Intel Speed Select Technology is supported thru a
corresponding driver. This driver provides an access to the
features of the ISST, such as Performance Profile, Core Power, Base
frequency and Turbo Frequency.
- Mellanox platform drivers has been refactored and now extended to
support more systems, including new coming ones.
- The OLPC XO-1.75 platform is now supported.
- CB4063 Beckhoff Automation board is using PMC clocks, provided via
pmc_atom driver, for ethernet controllers in a way that they can't
be managed by the clock driver. The quirk has been extended to
cover this case.
- Touchscreen on Chuwi Hi10 Plus tablet has been enabled. Meanwhile
the information of Chuwi Hi10 Air has been fixed to cover more
models based on the same platform.
- Xiaomi notebooks have WMI interface enabled. Thus, the driver to
support it has been provided. It required some extension of the
generic WMI library, which allows to propagate opaque context to
the ->probe() of the individual drivers.
This release includes debugfs clean up from Greg KH for several
drivers that drop return code check and make debugfs absence or
failure non-fatal.
Also miscellaneous fixes here and there, mostly for Acer WMI and
various Intel drivers"
* tag 'platform-drivers-x86-v5.3-1' of git://git.infradead.org/linux-platform-drivers-x86: (74 commits)
platform/x86: Fix PCENGINES_APU2 Kconfig warning
tools/power/x86/intel-speed-select: Add .gitignore file
platform/x86: mlx-platform: Fix error handling in mlxplat_init()
platform/x86: intel_pmc_core: Attach using APCI HID "INT33A1"
platform/x86: intel_pmc_core: transform Pkg C-state residency from TSC ticks into microseconds
platform/x86: asus-wmi: Use dev_get_drvdata()
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Add more reset cause attributes
platform/x86: mlx-platform: Modify DMI matching order
platform/x86: mlx-platform: Add regmap structure for the next generation systems
platform/x86: mlx-platform: Change API for i2c-mlxcpld driver activation
platform/x86: mlx-platform: Move regmap initialization before all drivers activation
MAINTAINERS: Update for Intel Speed Select Technology
tools/power/x86: A tool to validate Intel Speed Select commands
platform/x86: ISST: Restore state on resume
platform/x86: ISST: Add Intel Speed Select PUNIT MSR interface
platform/x86: ISST: Add Intel Speed Select mailbox interface via MSRs
platform/x86: ISST: Add Intel Speed Select mailbox interface via PCI
platform/x86: ISST: Add Intel Speed Select mmio interface
platform/x86: ISST: Add IOCTL to Translate Linux logical CPU to PUNIT CPU number
...
|
|
Without CONFIG_OF, we get a build failure in the reboot-mode
implementation:
drivers/power/reset/reboot-mode.c: In function 'reboot_mode_register':
drivers/power/reset/reboot-mode.c:72:2: error: implicit declaration of function 'for_each_property_of_node'; did you mean 'for_each_child_of_node'? [-Werror=implicit-function-declaration]
for_each_property_of_node(np, prop) {
Add a Kconfig dependency like we have for the other users of
CONFIG_REBOOT_MODE.
Fixes: 7a78a7f7695b ("power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
* pm-opp:
opp: Don't use IS_ERR on invalid supplies
opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes
opp: Don't overwrite rounded clk rate
opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()
opp: Attach genpds to devices from within OPP core
* pm-misc:
PM / clk: Remove error message on out-of-memory condition
drivers: base: power: clock_ops: Use of_clk_get_parent_count()
* pm-avs:
power: avs: smartreflex: no need to check return value of debugfs_create functions
* pm-tools:
cpupower : frequency-set -r option misses the last cpu in related cpu list
cpupower: correct spelling of interval
Add README and update pm-graph and sleepgraph docs
Update to pm-graph 5.4
Update to pm-graph 5.3
|
|
Add a driver to control the charging algorithm used on Wilco
devices. See Documentation/ABI/testing/sysfs-class-power-wilco
for the userspace interface and other info.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This patch allows reading and writing the input voltage and current
limit through the POWER_SUPPLY_PROP_INPUT_VOLTAGE_LIMIT and
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT sysfs properties. This allows
userspace to see current values and to re-configure these values at
runtime based on system-level knowledge or user input.
By default there is no limit, this is reported as a -1 when reading from
userspace. Writing a value will set the current or voltage limit in uA
or uV, and writing any negative value will remove that limit.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
For thermal management strategy you might be interested on limit the
input power for a power supply. We already have current limit but
basically what we probably want is to limit power. So, introduce the
input_power_limit property.
Although the common use case is limit the input power, in some
specific cases it is the voltage that is problematic (i.e some regulators
have different efficiencies at higher voltage resulting in more heat).
So introduce also the input_voltage_limit property.
This happens in one Chromebook and is used on the Pixel C's thermal
management strategy to effectively limit the input power to 5V 3A when
the screen is on. When the screen is on, the display, the CPU, and the GPU
all contribute more heat to the system than while the screen is off, and
we made a tradeoff to throttle the charger in order to give more of the
thermal budget to those other components.
So there's nothing fundamentally broken about the hardware that would
cause the Pixel C to malfunction if we were charging at 9V or 12V instead
of 5V when the screen is on, i.e. if userspace doesn't change this.
What would happen is that you wouldn't meet Google's skin temperature
targets on the system if the charger was allowed to run at 9V or 12V with
the screen on.
For folks hacking on Pixel Cs (which is now outside of Google's official
support window for Android) and customizing their own kernel and userspace
this would be acceptable, but we wanted to expose this feature in the
power supply properties because the feature does exist in the Emedded
Controller firmware of the Pixel C and all of Google's Chromebooks with
USB-C made since 2015 in case someone running an up to date kernel wanted
to limit the charging power for thermal or other reasons.
This patch exposes a new property, similar to input current limit, to
re-configure the maximum voltage from the external supply at runtime
based on system-level knowledge or user input.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
ROHM BD70528 PMIC includes battery charger block. Support charger
staus queries and doing few basic settings like input current limit
and charging current.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
drivers/power/supply/ucs1002_power.c:339:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Fixes: 9a2688e42638 ("power: supply: Add driver for Microchip UCS1002")
CC: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add a new reboot mode write interface that is using an NVMEM cell
to store the reboot mode magic.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for gen2 pon register so "reboot bootloader" can
work on pixel3 and db845.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
v2:
* Split out dts changes into separate path
* Minor cleanups and remove unused variables
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add code implementing HWMON adapter/compatibility layer to allow
expositing various sensors present on power supply devices via HWMON
subsystem. This is done in order to allow userspace to use single
ABI/library(libsensors) to access/manipulate all of the sensors of the
system.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
client
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
