summaryrefslogtreecommitdiff
path: root/drivers/lightnvm/Makefile
AgeCommit message (Collapse)AuthorFilesLines
2018-01-05lightnvm: remove rrpcMatias Bjørling1-1/+0
The hybrid mode for 1.2 revision was deprecated, and have no users. Remove to make it easier to move to the 2.0 revision. Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-16lightnvm: physical block device (pblk) targetJavier González1-0/+5
This patch introduces pblk, a host-side translation layer for Open-Channel SSDs to expose them like block devices. The translation layer allows data placement decisions, and I/O scheduling to be managed by the host, enabling users to optimize the SSD for their specific workloads. An open-channel SSD has a set of LUNs (parallel units) and a collection of blocks. Each block can be read in any order, but writes must be sequential. Writes may also fail, and if a block requires it, must also be reset before new writes can be applied. To manage the constraints, pblk maintains a logical to physical address (L2P) table, write cache, garbage collection logic, recovery scheme, and logic to rate-limit user I/Os versus garbage collection I/Os. The L2P table is fully-associative and manages sectors at a 4KB granularity. Pblk stores the L2P table in two places, in the out-of-band area of the media and on the last page of a line. In the cause of a power failure, pblk will perform a scan to recover the L2P table. The user data is organized into lines. A line is data striped across blocks and LUNs. The lines enable the host to reduce the amount of metadata to maintain besides the user data and makes it easier to implement RAID or erasure coding in the future. pblk implements multi-tenant support and can be instantiated multiple times on the same drive. Each instance owns a portion of the SSD - both regarding I/O bandwidth and capacity - providing I/O isolation for each case. Finally, pblk also exposes a sysfs interface that allows user-space to peek into the internals of pblk. The interface is available at /dev/block/*/pblk/ where * is the block device name exposed. This work also contains contributions from: Matias Bjørling <matias@cnexlabs.com> Simon A. F. Lund <slund@cnexlabs.com> Young Tack Jin <youngtack.jin@gmail.com> Huaicheng Li <huaicheng@cs.uchicago.edu> Signed-off-by: Javier González <javier@cnexlabs.com> Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-01-31lightnvm: merge gennvm with coreMatias Bjørling1-2/+1
For the first iteration of Open-Channel SSDs, it was anticipated that there could be various media managers on top of an open-channel SSD, such to allow vendors to plug in their own host-side FTLs, without the media manager in between. Now that an Open-Channel SSD is exposed as a traditional block device, there is no longer a need for this. Therefore lets merge the gennvm code with core and simplify the stack. Signed-off-by: Matias Bjørling <matias@cnexlabs.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-29nvme: lightnvm: attach lightnvm sysfs to nvme block deviceMatias Bjørling1-1/+1
Previously, LBA read and write were not supported in the lightnvm specification. Now that it supports it, lets use the traditional NVMe gendisk, and attach the lightnvm sysfs geometry export. Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-09-21lightnvm: expose device geometry through sysfsSimon A. F. Lund1-1/+1
For a host to access an Open-Channel SSD, it has to know its geometry, so that it writes and reads at the appropriate device bounds. Currently, the geometry information is kept within the kernel, and not exported to user-space for consumption. This patch exposes the configuration through sysfs and enables user-space libraries, such as liblightnvm, to use the sysfs implementation to get the geometry of an Open-Channel SSD. The sysfs entries are stored within the device hierarchy, and can be found using the "lightnvm" device type. An example configuration looks like this: /sys/class/nvme/ └── nvme0n1 ├── capabilities: 3 ├── device_mode: 1 ├── erase_max: 1000000 ├── erase_typ: 1000000 ├── flash_media_type: 0 ├── media_capabilities: 0x00000001 ├── media_type: 0 ├── multiplane: 0x00010101 ├── num_blocks: 1022 ├── num_channels: 1 ├── num_luns: 4 ├── num_pages: 64 ├── num_planes: 1 ├── page_size: 4096 ├── prog_max: 100000 ├── prog_typ: 100000 ├── read_max: 10000 ├── read_typ: 10000 ├── sector_oob_size: 0 ├── sector_size: 4096 ├── media_manager: gennvm ├── ppa_format: 0x380830082808001010102008 ├── vendor_opcode: 0 ├── max_phys_secs: 64 └── version: 1 Signed-off-by: Simon A. F. Lund <slund@cnexlabs.com> Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-01-12lightnvm: core on-disk initializationMatias Bjørling1-1/+1
An Open-Channel SSD shall be initialized before use. To initialize, we define an on-disk format, that keeps a small set of metadata to bring up the media manager on top of the device. The initial step is introduced to allow a user to format the disks for a given media manager. During format, a system block is stored on one to three separate luns on the device. Each lun has the system block duplicated. During initialization, the system block can be retrieved and the appropriate media manager can initialized. The on-disk format currently covers (struct nvm_system_block): - Magic value "NVMS". - Monotonic increasing sequence number. - The physical block erase count. - Version of the system block format. - Media manager type. - Media manager superblock physical address. The interface provides three functions to manage the system block: int nvm_init_sysblock(struct nvm_dev *, struct nvm_sb_info *) int nvm_get_sysblock(struct nvm *dev, struct nvm_sb_info *) int nvm_update_sysblock(struct nvm *dev, struct nvm_sb_info *) Each implement a part of the logic to manage the system block. The initialization creates the first system blocks and mark them on the device. Get retrieves the latest system block by scanning all pages in the associated system blocks. The update sysblock writes new metadata and allocates new block if necessary. Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-10-29rrpc: Round-robin sector target with cost-based gcMatias Bjørling1-0/+1
This target allows an Open-Channel SSD to be exposed asas a block device. It implements a round-robin approach for sector allocation, together with a greedy cost-based garbage collector. Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-10-29gennvm: Generic NVM managerMatias Bjørling1-0/+1
The implementation for Open-Channel SSDs is divided into media management and targets. This patch implements a generic media manager for open-channel SSDs. After a media manager has been initialized, single or multiple targets can be instantiated with the media managed as the backend. Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-10-29lightnvm: Support for Open-Channel SSDsMatias Bjørling1-0/+5
Open-channel SSDs are devices that share responsibilities with the host in order to implement and maintain features that typical SSDs keep strictly in firmware. These include (i) the Flash Translation Layer (FTL), (ii) bad block management, and (iii) hardware units such as the flash controller, the interface controller, and large amounts of flash chips. In this way, Open-channels SSDs exposes direct access to their physical flash storage, while keeping a subset of the internal features of SSDs. LightNVM is a specification that gives support to Open-channel SSDs LightNVM allows the host to manage data placement, garbage collection, and parallelism. Device specific responsibilities such as bad block management, FTL extensions to support atomic IOs, or metadata persistence are still handled by the device. The implementation of LightNVM consists of two parts: core and (multiple) targets. The core implements functionality shared across targets. This is initialization, teardown and statistics. The targets implement the interface that exposes physical flash to user-space applications. Examples of such targets include key-value store, object-store, as well as traditional block devices, which can be application-specific. Contributions in this patch from: Javier Gonzalez <jg@lightnvm.io> Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Jesper Madsen <jmad@itu.dk> Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>