| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add description for 'data' parameter and drop unused 'irq' memeber.
Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch try to add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add runtime pm support to dynamically manage the clock to avoid enable/disable
clock in frequently that can improve the i2c bus transfer performance.
And use pm_runtime_force_suspend/resume() instead of lpi2c_imx_suspend/resume().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Nothing big, but they get annoying after a while ;)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2c_davinci_cpufreq_transition() is implemented in a way that will
block if it ever gets called while no transfer is in progress.
Not only that, but reinit_completion() is never called for xfr_complete.
Use the fact that cpufreq uses an srcu_notifier (running in process
context) for transitions and that the bus_lock is taken during the call
to master_xfer() and simplify the code by removing the transfer
completion entirely and protecting i2c_davinci_cpufreq_transition()
with i2c_lock/unlock_adapter().
Reported-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
* pm-core: (29 commits)
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
PM: i2c-designware-platdrv: Optimize power management
PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
PM / core: Assign the wakeup_path status flag in __device_prepare()
PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
PM / core: Add helpers for subsystem callback selection
PM / wakeup: Drop redundant check from device_init_wakeup()
PM / wakeup: Drop redundant check from device_set_wakeup_enable()
PM / wakeup: only recommend "call"ing device_init_wakeup() once
...
|
|
gcc noticed the kerneldoc was wrongly formatted. Fix it!
drivers/i2c/busses/i2c-rk3x.c:164: warning:
Cannot understand * @grf_offset: ...
on line 164 - I thought it was a doc line
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
|
|
This driver creates a number of const structures that it stores in
the data field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified. The
const-discarding cast on the extraction from the data field is thus
no longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
That path has gone away for a long time. Move the HW name upwards for a
proper header.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As of v4.15, Kbuild warns about missing MODULE_LICENSE tags:
WARNING: modpost: missing MODULE_LICENSE() in drivers/i2c/busses/i2c-acorn.o
This adds a license, author and description tag, matching the
comment at the start of the acorn i2c driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.
It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.
This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.
Call Trace:
[<ffffffff8139f695>] dump_stack+0x67/0x92
[<ffffffff811802a4>] panic+0xc5/0x1eb
[<ffffffff810ecb5f>] ? vprintk_default+0x1f/0x30
[<ffffffff817456d3>] ? i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff8109a68b>] __stack_chk_fail+0x1b/0x20
[<ffffffff817456d3>] i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff81745aed>] i2cdev_ioctl+0x4d/0x1e0
[<ffffffff811f761a>] do_vfs_ioctl+0x2ba/0x490
[<ffffffff81336e43>] ? security_file_ioctl+0x43/0x60
[<ffffffff811f7869>] SyS_ioctl+0x79/0x90
[<ffffffff81a22e97>] entry_SYSCALL_64_fastpath+0x12/0x6a
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Reference count of device node was increased in of_i2c_register_device,
but without decreasing it in i2c_unregister_device. Then the added
device node will never be released. Fix this by adding the of_node_put.
Signed-off-by: Lixin Wang <alan.1.wang@nokia-sbell.com>
Tested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
We can force levels of SCL and SDA, so we can use that for bus recovery.
Note that we cannot read SDA back, because we will only get the internal
state of the bus free detection.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we managed to get a client release SDA again, send a STOP afterwards
to make sure we have a consistent state on the bus again.
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we have a function to control SDA, we should ensure that SDA is not
held down by us. So, release the GPIO in this case.
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This will be needed when we want to create STOP conditions, too, later.
Create the needed fields and populate them for the GPIO case if the GPIO
is set to output.
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Exynos-I2C uses default timeout of 1 second for the whole transaction,
including re-transmissions due to arbitration lost errors (-EAGAIN).
To allow re-transmissions driver's internal timeout should be significantly
lower, 100ms seems to be good candidate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use only a portion of the data buffer for DMA transfers, which is always
16-byte aligned. This makes the DMA buffer address 16-byte aligned and
compensates for spurious hardware parity errors that may appear when the
DMA buffer address is not 16-byte aligned.
The data buffer is enlarged in order to accommodate any possible 16-byte
alignment offset and changes the DMA code to only use a portion of the
data buffer, which is 16-byte aligned.
The symptom of the hardware issue is the same as the one addressed in
v3.12-rc2-5-gbf41691 and manifests by transfers failing with EIO, with
bit 9 being set in the ERRSTS register.
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Remove the facility for setting the prescaler value at compile time
entirely. It was only used for two SoCs, duplicating the actual value
for one of them and setting sometimes bogus value for another. Make all
MPC8xxx SoCs obtain their actual I2C clock prescaler from a single place
in the code.
Changes from v2:
- left Device Tree compatibles in place
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to the reference manuals for the corresponding SoCs, SEC
frequency ratio configuration is indicated by bit 26 of the POR Device
Status Register 2. Consequently, SEC_CFG bit should be tested by mask 0x20,
not 0x80. Testing the wrong bit leads to selection of wrong I2C clock
prescaler on those SoCs.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit 8ce795cb0c6b ("i2c: mpc: assign the correct prescaler from SVR")
introduced the common helper function for obtaining the actual clock
prescaler value for MPC85xx. However, getting the prescaler for MPC8544
which depends on the SEC frequency ratio on this platform, has been always
performed separately based on the corresponding Device Tree configuration.
Move special handling of MPC8544 into that common helper. Make it dependent
on the SoC version and not on Device Tree compatible node, as is the case
with all other SoCs. Handle MPC8533 the same way which is similar
to MPC8544 in this regard, according to AN2919 "Determining the I2C
Frequency Divider Ratio for SCL".
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Obtaining the actual I2C clock prescaler value in mpc_i2c_setup_8xxx() only
happens when the clock parameter is set to something other than
MPC_I2C_CLOCK_LEGACY. When the clock parameter is exactly
MPC_I2C_CLOCK_LEGACY, the prescaler parameter is used in arithmetic
division as provided by the caller, resulting in a division by zero
for the majority of processors supported by the module.
Avoid division by zero by obtaining the actual I2C clock prescaler
in mpc_i2c_setup_8xxx() unconditionally regardless of the passed clock
value.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch dumps general and master registers at the end of transactions
when debugging is enabled. Previously, registers were only dumped before
submitting new descriptors (at the beginning of transactions).
This helps debugging if some registers change as result of a failed
transaction (e.g. bits are set in the ERRSTS general register).
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make use of the new formula for more precise bus frequencies.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The formula to generate the desired bus speeds has changed a little over
time. Implement the new formula and allow drivers to opt-in by changing
to this new config set. Ensure in probe that we don't divide by zero.
The returned values on a R-Car H2 (r8a7790/Lager board) match the
suggested values in the datasheet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Because we will add a second formula soon, put the sanity checks for the
computed results into a separate function.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Start RuntimePM a bit earlier, so we can use it to enable the clock
during probe for frequency calculations. Make sure it is enabled before
calling setup().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Require the setup callback and move the frequency calculation into it.
This is in preparation for supporting multiple formulas.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The setup callback will be more generic and, thus, need to be able to
return error codes. Change the return type to 'int' for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
For refactoring reasons, we will need this information before the setup
callback. Also, simplify the comment to a oneliner.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Optimize the power management in i2c-designware-platdrv by making it
set the DPM_FLAG_SMART_SUSPEND and DPM_FLAG_LEAVE_SUSPENDED which
allows some code to be dropped from its PM callbacks.
First, setting DPM_FLAG_SMART_SUSPEND causes the intel-lpss driver
to avoid resuming i2c-designware-platdrv devices in its ->prepare
callback, so they can stay in runtime suspend after that point even
if the direct-complete feature is not used for them.
It also causes the ACPI PM domain and the PM core to avoid invoking
"late" and "noirq" suspend callbacks for these devices if they are
in runtime suspend at the beginning of the "late" phase of device
suspend during system suspend. That guarantees dw_i2c_plat_suspend()
to be called for a device only if it is not in runtime suspend.
Moreover, it causes the device's runtime PM status to be set to
"active" after calling dw_i2c_plat_resume() for it, so the
driver doesn't need internal flags to avoid invoking either
dw_i2c_plat_suspend() or dw_i2c_plat_resume() twice in a row.
Second, setting DPM_FLAG_LEAVE_SUSPENDED enables the optimization
allowing the device to stay suspended after system resume under
suitable conditions, so again the driver doesn't need to take
care of that by itself.
Accordingly, the internal "suspended" and "skip_resume" flags
used by the driver are not necessary any more, so drop them and
simplify the driver's PM callbacks.
Additionally, notice that dw_i2c_plat_complete() only needs to
schedule runtime PM resume for the device if platform firmware
has been involved in resuming the system, so make it call
pm_resume_via_firmware() to check that. Also make it check the
runtime PM status of the device instead of its direct_complete
flag which also works if the device remained suspended due to
the DPM_FLAG_LEAVE_SUSPENDED driver flag.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
|
|
Modify i2c-designware-platdrv to set DPM_FLAG_SMART_PREPARE for its
devices and return 0 from the system suspend ->prepare callback
if the device has an ACPI companion object in order to tell the PM
core and middle layers to avoid skipping system suspend/resume
callbacks for the device in that case (which may be problematic,
because the device may be accessed during suspend and resume of
other devices via I2C operation regions then).
Also the pm_runtime_suspended() check in dw_i2c_plat_prepare()
is not necessary any more, because the core does it when setting
power.direct_complete for the device, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
|
|
This is the pxa changes for v4.16 cycle.
It is :
- the conversion to the new parser sharpslpart parser
for the Sharp variants
- an I2C platform data cleanup for PXA
- a gpioreg switch of one register for lubbock
* tag 'pxa-for-4.16' of https://github.com/rjarzmik/linux:
ARM: pxa/lubbock: add GPIO driver for LUB_MISC_WR register
ARM: pxa/poodle: Remove hardcoded partitioning, use sharpslpart parser
ARM: pxa/spitz: Remove hardcoded partitioning, use sharpslpart parser
ARM: pxa/tosa: Remove hardcoded partitioning, use sharpslpart parser
ARM: pxa/corgi: Remove hardcoded partitioning, use sharpslpart parser
ARM: pxa: move header file out of I2C realm
ARM: pxa: move declarations to proper place
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"Slow" GPIOs (usually those connected over an SPI or an I2C bus) are,
well, slow in their operation. It is generally a good idea to avoid
using them for time-critical operation, but sometimes the hardware just
sucks, and the software has to cope. In addition to that, the I2C bus
itself does not actually define any strict timing limits; the bus is
free to go all the way down to DC. The timeouts (and therefore the
slowest acceptable frequency) are present only in SMBus.
The `can_sleep` is IMHO a wrong concept to use here. My SPI-to-quad-UART
chip (MAX14830) is connected via a 26MHz SPI bus, and it happily drives
SCL at 200kHz (5µs pulses) during my benchmarks. That's faster than the
maximal allowed speed of the traditional I2C.
The previous version of this code did not really block operation over
slow GPIO pins, anyway. Instead, it just resorted to printing a warning
with a backtrace each time a GPIO pin was accessed, thereby slowing
things down even more.
Finally, it's not just me. A similar patch was originally submitted in
2015 [1].
[1] https://patchwork.ozlabs.org/patch/450956/
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make sure i2c module clock has been enabled before i2c registers
access.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add i2c compatible for MT2712. Compare to MT8173 i2c controller,
internal divider of i2c source clock need to be configured for
MT2712 i2c speed calculation.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.16
"AT24 updates for 4.16 merge window
The driver has been converted to using regmap instead of raw i2c and
smbus calls which shrank the code significantly.
Device tree binding document has been cleaned up. Device tree support in
the driver has been improved and we now support all at24 models as well
as two new DT properties (no-read-rollover and wp-gpios).
We no longer user unreadable magic values for driver data as the way it
was implemented caused problems for some EEPROM models - we switched to
regular structs.
Aside from that, there's a bunch of coding style fixes and minor
improvements all over the place."
|
|
i2c/for-4.16
"A couple of patches this time. Just some more compatibles for the
pca954x driver and an error handling tweak for the reg driver."
|
|
...which takes care of proper format and size of the value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Ensure the bus is free when we register the adapter. Before the SCL/SDA
wires were in an unknown state. It used to work because sending a byte
has a retry mechanism which was triggered if the bus was initially in a
non-free state. But the graceful way to do it is to initialize
correctly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Alter the DaVinci GPIO recovery fetch to use descriptors
all the way down into the board files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
It's possible that i2c_mux_reg_probe_dt() could return -EPROBE_DEFER.
In that case, driver will request a probe deferral and an error
suggesting device tree parsing problem will be reported. This is
a pretty confusing information. Let's change the error handling,
so driver will be able to request probe deferral without logging
not related errors.
Signed-off-by: Tomasz Bachorski <tomasz.bachorski@nokia.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
This patch extends the current i2c-mux-pca954x driver and adds support for
a newer PCA984x family of the I2C switches and multiplexers from NXP.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
<linux/of_gpio.h> is not used in this file, by
<linux/gpio/consumer.h> is.
Someone is just lucky with their implicit includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
