| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This change add the regulator/clock configuration for MDP5 v1.3.
This config is close to the one already existing for 8x74, except
that one more regulator is needed (hpd-5v-en).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Instead of reporting BUG_ON when resources arrays are not
dimensioned correctly, this patch does a dynamic allocation of
these arrays. This is needed for the following patches that add a
regulator for a new target.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Resync from rnndb database, to pull in register defines for:
* eDP
* HDMI/HDCP
* mdp4/mdp5 YUV support
* mdp5 hw cursor support
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
3d3f8b1f8b ("drm/bridge: make bridge registration independent of drm
flow") resulted that the hdmi bridge object would be leaked at teardown.
Just switch over to devm_kzalloc() as the easy way to solve this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Disable the HPD interrupt when acking it, to avoid spurious
interrupt.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
|
|
HPD regulators need to be enabled before clocks, otherwise clock
driver will report warning.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
|
|
A left-over from prior to component framework. The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways. These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block. In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5. When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal. When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:
mdp: qcom,mdss_mdp@fd900000 {
compatible = "qcom,mdss_mdp";
interrupt-controller;
#interrupt-cells = <1>;
...
};
hdmi: qcom,hdmi_tx@fd922100 {
compatible = "qcom,hdmi-tx-8074";
interrupt-parent = <&mdp>;
interrupts = <8 0>; /* MDP5_HW_INTR_STATUS.INTR_HDMI */
...
};
There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block. So
you must not use threaded irq handlers in the child. I'm not sure
if there is a better way to deal with that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Split up hdmi_init() into hdmi_init() (done at hdmi sub-device
bind/probe time) and hdmi_modeset_init() done from master driver's
modeset_init().
Anything that can fail due to dependencies on other drivers which
may be missing or not probed yet should go in hdmi_init(), so that
devm error/cleanup paths work properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
|
|
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
There is currently a nested function in Russel King's tree
for the msm HDMI driver.
The last nested function was removed from the Linux kernel
when the Thinkpad driver was fixed.
I believe nested functions are not desired upstream, and it
also breaks compilation with clang so here is a patch to
change the nested function into static function. The patch
works with both clang and gcc.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
In particular, pick up the definitions for a handful of LVDS related
registers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
HDMI_MUX_EN gpio is requested. If an error occurs, the same name
should be printed (HDMI_MUX_EN) instead of HDMI_MUX_SEL (typo).
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
lpm-mux is programmed to enable HDMI connector
on the docking station for S805 chipset based
devices.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
On downstream kernel the clk driver directly bangs hdmi phy registers.
For upstream kernel, we need to model this as a clock and register with
the clock framework.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
|
|
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The hotplug detect and irq does not seem to be reliable on all devices
for some reason. For now it is more reliable to use polling, and give
preference to raw gpio status if it disagrees with the debounced hpd
status.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
resync to latest envytools db, add mdp5 registers
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
resync to latest envytools db, fixes a typo: s/mpd4/mdp4/
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
Drop the msm_connector base class, and special calls to base class
methods from the encoder, and use instead drm_bridge. This allows for a
cleaner division between the hdmi (and in future dsi) blocks, from the
mdp block.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Generated from rnndb files in:
https://github.com/freedreno/envytools
Keep this split out as a separate commit to make it easier to review the
actual driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
