| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Ever since v2.6.19 the code contains a check for CONFIG_NO_ATA_LEGACY.
But that macro has never been defined. Apparently no one ran into
problems on platforms that do not support compatibility mode. So remove
this code that has been dead for over seven years.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The SCSI-to-ATA Translation standard says to use data words 25 and 26
unless they are spaces. For devices that use these words in the firmware
field, they are generally more useful anyway.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
|
|
On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In multiple MSI mode all AHCI ports (including dummy) get assigned
separate MSI vectors and (as result of execution
pci_enable_msi_exact() function) separate IRQ numbers, (mapped to the
MSI vectors).
Therefore, although interrupts from dummy ports are not desired they
are still enabled. We do not request IRQs for dummy ports, but that
only means we do not assign AHCI-specific ISRs to corresponding IRQ
numbers.
As result, dummy port interrupts still could come and traverse all the
way from the PCI device to the kernel, causing unnecessary overhead.
This update disables IRQs for dummy ports and prevents the described
issue.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: David Milburn <dmilburn@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 5ca72c4f7c41 ("AHCI: Support multiple MSIs")
|
|
The driver calls pci_enable_msi_range() function with the range of
[nvec..nvec] which is what pci_enable_msi_exact() function is for.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The AHCI specification allows hardware to choose to revert to
single MSI mode when fewer messages are allocated than requested.
Yet, at least ICH10 chipset reverts to single MSI mode even when
enough messages are allocated in some cases (see below).
This update forces the driver to not rely on initialization of
multiple MSIs mode alone and always check if "MSI Revert to
Single Message" (MRSM) mode was enforced by the controller and
fallback to the single MSI mode in case it did.
That prevents a situation when the driver configured multiple
per-port IRQ handlers, but the controller sends all port's
interrupts to a single IRQ, which could easily screw up the
interrupt handling and lead to delays and possibly crashes.
The fix was tested on a 6-port controller that successfully
reverted to the single MSI mode:
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device 10a7
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101
I/O ports at f110 [size=8]
I/O ports at f100 [size=4]
I/O ports at f0f0 [size=8]
I/O ports at f0e0 [size=4]
I/O ports at f020 [size=32]
Memory at fbf00000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Capabilities: [b0] PCI Advanced Features
Kernel driver in use: ahci
With 6 ports just 8 MSI vectors should be enough, but the adapter
enforces the MRSM mode when less than 16 vectors are written to
the Multiple Messages Enable PCI register. I instigated MRSM mode
by forcing @nvec to 8 in ahci_init_interrupts().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
System may crash in ahci_hw_interrupt() or ahci_thread_fn() when
accessing the interrupt status in a port's private_data if the port is
actually a DUMMY port.
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller
<snip console output for linux-3.15-rc1>
[ 9.352080] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x1 impl SATA mode
[ 9.352084] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
[ 9.368155] Console: switching to colour frame buffer device 128x48
[ 9.439759] mgag200 0000:11:00.0: fb0: mgadrmfb frame buffer device
[ 9.446765] mgag200 0000:11:00.0: registered panic notifier
[ 9.470166] scsi1 : ahci
[ 9.479166] scsi2 : ahci
[ 9.488172] scsi3 : ahci
[ 9.497174] scsi4 : ahci
[ 9.506175] scsi5 : ahci
[ 9.515174] scsi6 : ahci
[ 9.518181] ata1: SATA max UDMA/133 abar m2048@0x95c00000 port 0x95c00100 irq 91
[ 9.526448] ata2: DUMMY
[ 9.529182] ata3: DUMMY
[ 9.531916] ata4: DUMMY
[ 9.534650] ata5: DUMMY
[ 9.537382] ata6: DUMMY
[ 9.576196] [drm] Initialized mgag200 1.0.0 20110418 for 0000:11:00.0 on minor 0
[ 9.845257] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9.865161] ata1.00: ATAPI: Optiarc DVD RW AD-7580S, FX04, max UDMA/100
[ 9.891407] ata1.00: configured for UDMA/100
[ 9.900525] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7580S FX04 PQ: 0 ANSI: 5
[ 10.247399] iTCO_vendor_support: vendor-support=0
[ 10.261572] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 10.269764] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 10.301932] sd 0:2:0:0: [sda] 570310656 512-byte logical blocks: (291 GB/271 GiB)
[ 10.317085] sd 0:2:0:0: [sda] Write Protect is off
[ 10.328326] sd 0:2:0:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
[ 10.375452] BUG: unable to handle kernel NULL pointer dereference at 000000000000003c
[ 10.384217] IP: [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[ 10.392101] PGD 0
[ 10.394353] Oops: 0000 [#1] SMP
[ 10.397978] Modules linked in: sr_mod(+) cdrom sd_mod iTCO_wdt crc_t10dif iTCO_vendor_support crct10dif_common ahci libahci libata lpc_ich mfd_core mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm drm i2c_core megaraid_sas dm_mirror dm_region_hash
dm_log dm_mod
[ 10.426499] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.15.0-rc1 #1
[ 10.433495] Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.S013.032920111005 03/29/2011
[ 10.443886] task: ffffffff81906460 ti: ffffffff818f0000 task.ti: ffffffff818f0000
[ 10.452239] RIP: 0010:[<ffffffffa0133df0>] [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[ 10.462838] RSP: 0018:ffff880033c03d98 EFLAGS: 00010046
[ 10.468767] RAX: 0000000000a400a4 RBX: ffff880029a6bc18 RCX: 00000000fffffffa
[ 10.476731] RDX: 00000000000000a4 RSI: ffff880029bb0000 RDI: ffff880029a6bc18
[ 10.484696] RBP: ffff880033c03dc8 R08: 0000000000000000 R09: ffff88002f800490
[ 10.492661] R10: 0000000000000000 R11: 0000000000000005 R12: 0000000000000000
[ 10.500625] R13: ffff880029a6bd98 R14: 0000000000000000 R15: ffffc90000194000
[ 10.508590] FS: 0000000000000000(0000) GS:ffff880033c00000(0000) knlGS:0000000000000000
[ 10.517623] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 10.524035] CR2: 000000000000003c CR3: 00000000328ff000 CR4: 00000000000007b0
[ 10.531999] Stack:
[ 10.534241] 0000000000000017 ffff880031ba7d00 000000000000005c ffff880031ba7d00
[ 10.542535] 0000000000000000 000000000000005c ffff880033c03e10 ffffffff810c2a1e
[ 10.550827] ffff880031ae2900 000000008108fb4f ffff880031ae2900 ffff880031ae2984
[ 10.559121] Call Trace:
[ 10.561849] <IRQ>
[ 10.563994] [<ffffffff810c2a1e>] handle_irq_event_percpu+0x3e/0x1a0
[ 10.571309] [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60
[ 10.577631] [<ffffffff810c4fdd>] try_one_irq.isra.6+0x8d/0xf0
[ 10.584142] [<ffffffff810c5313>] note_interrupt+0x173/0x1f0
[ 10.590460] [<ffffffff810c2a8e>] handle_irq_event_percpu+0xae/0x1a0
[ 10.597554] [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60
[ 10.603872] [<ffffffff810c5727>] handle_edge_irq+0x77/0x130
[ 10.610199] [<ffffffff81014b8f>] handle_irq+0xbf/0x150
[ 10.616040] [<ffffffff8109ff4e>] ? vtime_account_idle+0xe/0x50
[ 10.622654] [<ffffffff815fca1a>] ? atomic_notifier_call_chain+0x1a/0x20
[ 10.630140] [<ffffffff816038cf>] do_IRQ+0x4f/0xf0
[ 10.635490] [<ffffffff815f8aed>] common_interrupt+0x6d/0x6d
[ 10.641805] <EOI>
[ 10.643950] [<ffffffff8149ca9f>] ? cpuidle_enter_state+0x4f/0xc0
[ 10.650972] [<ffffffff8149ca98>] ? cpuidle_enter_state+0x48/0xc0
[ 10.657775] [<ffffffff8149cb47>] cpuidle_enter+0x17/0x20
[ 10.663807] [<ffffffff810b0070>] cpu_startup_entry+0x2c0/0x3d0
[ 10.670423] [<ffffffff815dfcc7>] rest_init+0x77/0x80
[ 10.676065] [<ffffffff81a60f47>] start_kernel+0x40f/0x41a
[ 10.682190] [<ffffffff81a60941>] ? repair_env_string+0x5c/0x5c
[ 10.688799] [<ffffffff81a60120>] ? early_idt_handlers+0x120/0x120
[ 10.695699] [<ffffffff81a605ee>] x86_64_start_reservations+0x2a/0x2c
[ 10.702889] [<ffffffff81a60733>] x86_64_start_kernel+0x143/0x152
[ 10.709689] Code: a0 fc ff 85 c0 8b 4d d4 74 c3 48 8b 7b 08 89 ca 48 c7 c6 60 66 13 a0 31 c0 e8 9d 70 28 e1 8b 4d d4 eb aa 0f 1f 84 00 00 00 00 00 <45> 8b 64 24 3c 48 89 df e8 23 47 4c e1 41 83 fc 01 19 c0 48 83
[ 10.731470] RIP [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[ 10.739441] RSP <ffff880033c03d98>
[ 10.743333] CR2: 000000000000003c
[ 10.747032] ---[ end trace b6e82636970e2690 ]---
[ 10.760190] Kernel panic - not syncing: Fatal exception in interrupt
[ 10.767291] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-of-by: David Milburn <dmilburn@redhat.com>
Fixes: 5ca72c4f7c41 ("AHCI: Support multiple MSIs")
|
|
Add missing clk_disable() call to ata_host_activate() failure path.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add missing cf_exit() and clk_put() calls to ata_host_activate()
failure path.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
As a nice side effect this fixes the cf_port leak on
dma_coerce_mask_and_coherent() or ata_host_activate()
failure.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The ahci_imx driver is only needed on Freescale i.MX platforms so
don't let it be built on other platforms, except for build test
purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
|
|
Add missing clk_put() call to ata_host_activate() failure path.
Sergei says,
"Hm, I have once fixed that (see that *if* (!ret)) but looks like a
later commit 477c87e90853d136b188c50c0e4a93d01cad872e (ARM:
at91/pata: use gpio_is_valid to check the gpio) broke it again. :-(
Would be good if the changelog did mention that..."
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Crucial/Micron M500 drives properly support queued DSM TRIM starting
with firmware MU05. Update the blacklist so we only disable queued trim
for older firmware releases.
Early M550 series drives suffer from the same issue as M500. A bugfix
firmware is in the pipeline but not ready yet. Until then, blacklist
queued trim for M550.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Chris Samuel <chris@csamuel.org>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
AHCI_XGENE is only applicable on ARM64 but it can also be enabled for
compile testing; however, AHCI_XGENE selects PHY_XGENE which has other
arch specific dependencies. This leads to the following warning when
enabling it on other archs for compile testing.
warning: (AHCI_XGENE) selects PHY_XGENE which has unmet direct
dependencies (HAS_IOMEM && OF && (ARM64 || COMPILE_TEST))
Selecting a config option which itself has dependencies can easily
lead to broken configurations. For now, let's just make AHCI_XGENE
depend on PHY_XGENE which has all the necessary dependencies already.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Loc Ho <lho@apm.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"A lot of activities on libata side this time.
- A lot of changes around ahci. Various embedded platforms are
implementing ahci controllers. Some were built atop ahci_platform,
others were doing their own things. Hans made some structural
changes to libahci and librarized ahci_platform so that ahci
platform drivers can share more common code. A couple platform
drivers are added on top of that and several are added to replace
older drivers which were doing their own things (older ones are
scheduled to be removed).
- Dan finishes the patchset to make libata PM operations
asynchronous. Combined with one patch being routed through scsi,
this should speed resume measurably.
- Various fixes and cleanups from Bartlomiej and others"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (61 commits)
ata: fix Marvell SATA driver dependencies
ata: fix ARASAN CompactFlash PATA driver dependencies
ata: remove superfluous casts
ata: sata_highbank: remove superfluous cast
ata: fix Calxeda Highbank SATA driver dependencies
ata: fix R-Car SATA driver dependencies
ARM: davinci: da850: update SATA AHCI support
ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller
ata: move library code from ahci_platform.c to libahci_platform.c
ata: ahci_platform: fix ahci_platform_data->suspend method handling
libata: remove unused ata_sas_port_async_resume() stub
libata.h: add stub for ata_sas_port_resume
libata: async resume
libata, libsas: kill pm_result and related cleanup
ata: Fix compiler warning with APM X-Gene host controller driver
arm64: Add APM X-Gene SoC AHCI SATA host controller DTS entries
ata: Add APM X-Gene SoC AHCI SATA host controller driver
Documentation: Add documentation for the APM X-Gene SoC SATA host controller DTS binding
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
ata: ahci_sunxi: fix code formatting
...
|
|
Make sata_mv host driver depend on PCI || ARCH_DOVE || ARCH_KIRKWOOD ||
ARCH_MV78XX0 || ARCH_MVEBU || ARCH_ORION5X config options as Marvell
SATA support covers both Marvell PCI devices and Marvell Dove, Kirkwood,
MV78xx0, Armada 370/XP and Orion5x SoCs (for non-PCI devices the driver
to work requires suitable device tree node or platform device to be
defined). Additionally allow the driver build if COMPILE_TEST config
option is set.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Make pata_arasan_cf host driver depend on ARCH_SPEAR13XX config
option as ARASAN CompactFlash PATA support is specific to ST
SPEAr13xx SoCs and the driver to work requires suitable device
tree node (or platform device) to be defined. Additionally
allow the driver build if COMPILE_TEST config option is set.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Unreferenced casts of void * types are unnecessary so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
hpriv->plat_data is 'void *' so there is no need to cast it to
'struct ecx_plat_data *'.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Make sata_highbank host driver depend on ARCH_HIGHBANK config option
as Calxeda Highbank SATA support is specific to Calxeda Highbank
SoCs and the driver to work requires suitable device tree node to
be defined. Additionally allow the driver build if COMPILE_TEST
config option is set.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Make sata_rcar host driver depend on ARCH_SHMOBILE config option as
Renesas R-Car SATA support is specific to Renesas SoCs and the driver
to work requires suitable device tree node (or platform device) to be
defined. Additionally allow the driver build if COMPILE_TEST config
option is set.
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add the new ahci_da850 host driver.
Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.
Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value. The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support"). Fix it.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Improve overall system resume time by making libata link recovery
actions asynchronous relative to other resume events.
Link resume operations are performed using the scsi_eh thread, so
commands, particularly the sd resume start/stop command, will be held
off until the device exits error handling. Libata already flushes eh
with ata_port_wait_eh() in the port teardown paths, so there are no
concerns with async operation colliding with the end-of-life of the
ata_port object. Also, libata-core is already careful to flush
in-flight pm operations before another round of pm starts on the given
ata_port.
Reference: https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach
Cc: Len Brown <len.brown@intel.com>
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
[djbw: rebase on cleanup patch, changelog wordsmithing]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Tejun says:
"At least for libata, worrying about suspend/resume failures don't make
whole lot of sense. If suspend failed, just proceed with suspend. If
the device can't be woken up afterwards, that's that. There isn't
anything we could have done differently anyway. The same for resume, if
spinup fails, the device is dud and the following commands will invoke
EH actions and will eventually fail. Again, there really isn't any
*choice* to make. Just making sure the errors are handled gracefully
(ie. don't crash) and the following commands are handled correctly
should be enough."
The only libata user that actually cares about the result from a suspend
operation is libsas. However, it only cares about whether queuing a new
operation collides with an in-flight one. All libsas does with the
error is retry, but we can just let libata wait for the previous
operation before continuing.
Other cleanups include:
1/ Unifying all ata port pm operations on an ata_port_pm_ prefix
2/ Marking all ata port pm helper routines as returning void, only
ata_port_pm_ entry points need to fake a 0 return value.
3/ Killing ata_port_{suspend|resume}_common() in favor of calling
ata_port_request_pm() directly
4/ Killing the wrappers that just do a to_ata_port() conversion
5/ Clearly marking the entry points that do async operations with an
_async suffix.
Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch fixes an compiler warning with APM X-Gene host controller
driver when compiled with DEBUG enabled.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch adds support for the APM X-Gene SoC AHCI SATA host controller
driver. It requires the corresponding APM X-Gene SoC PHY driver. This
initial version only supports Gen3 speed.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
* acpi-hotplug:
ACPI / hotplug: Rework deferred execution of acpi_device_hotplug()
ACPI / dock: Update copyright notice
ACPI / dock: Drop remove_dock_dependent_devices()
ACPI / dock: Drop struct acpi_dock_ops and all code related to it
ACPI / ATA: Add hotplug contexts to ACPI companions of SATA devices
ACPI / dock: Add .uevent() callback to struct acpi_hotplug_context
ACPI / dock: Use callback pointers from devices' ACPI hotplug contexts
ACPI / dock: Use ACPI device object pointers instead of ACPI handles
ACPI / hotplug: Add .fixup() callback to struct acpi_hotplug_context
ACPI / hotplug / PCI: Do not clear event callback pointer for docks
ACPI / dock: Associate dock platform devices with ACPI device objects
ACPI / dock: Pass ACPI device pointer to acpi_device_is_battery()
ACPI / dock: Dispatch dock notifications from the global notify handler
|
|
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the check inside
ahci_platform_get_resources() accordingly.
Also while at it remove a needless line break.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the check inside
pata_imx_probe() accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
struct ahci_platform_data is deprecated (please see comments in
<linux/ahci_platform.h> for details). Convert ahci_st driver to
use custom ->host_stop method instead.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
* The config option for ahci_st driver was renamed from
CONFIG_SATA_AHCI_ST to CONFIG_AHCI_ST but Makefile was
not updated. Fix it (also while at it move the ahci_st
driver entry below ahci_imx and ahci_sunxi ones).
* Fix a few build issues in the ahci_st driver itself.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Now that we can directly get the ACPI device conterpart of the physical
ATA transport device, the odd_can_poweroff can be eliminated.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If ACPI handle for an ATA device is NULL, we shouldn't call
ata_dev_get_GTF as that function will use handle to do some ACPI
evaluation.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ZPODD is built on top of runtime PM functionality, it doesn't make sense
to have it in a kernel that doesn't have CONFIG_PM_RUNTIME set.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The SC1200 is a SoC based on the Geode GX1 32-bit x86 processor, so
its drivers are only needed on this architecture, except for build
testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This is where we disable IRQs on suspend and update the internal
power state during suspend/resume.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This device is designed specifically to run on ST-Microelectronics'
hardware. To ensure no attempts are made to run on anything incompatible
we add a dependency on ST architecture
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ata_platform_remove_one() allows us to specify our own exit function
via platform data then goes off and removes ATA Host and Port in
preparation for device removal.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Other devices have adopted similar naming conventions which have been
accepted as the standard. This patch brings any mention of the the ST
AHCI driver into line with them.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
