summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2019-08-29usb: cdns3: Add Cadence USB3 DRD DriverPawel Laszczak18-0/+6992
This patch introduce new Cadence USBSS DRD driver to Linux kernel. The Cadence USBSS DRD Controller is a highly configurable IP Core which can be instantiated as Dual-Role Device (DRD), Peripheral Only and Host Only (XHCI)configurations. The current driver has been validated with FPGA platform. We have support for PCIe bus, which is used on FPGA prototyping. The host side of USBSS-DRD controller is compliant with XHCI specification, so it works with standard XHCI Linux driver. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-29usb: common: Simplify usb_decode_get_set_descriptor function.Pawel Laszczak1-55/+58
Patch moves switch responsible for decoding descriptor type outside snprintf. It improves code readability a little. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-29usb: common: Patch simplify usb_decode_set_clear_feature function.Pawel Laszczak1-46/+43
Patch adds usb_decode_test_mode and usb_decode_device_feature functions, which allow to make more readable and simplify the usb_decode_set_clear_feature function. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-29usb: common: Separated decoding functions from dwc3 driver.Pawel Laszczak5-253/+297
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver to driver/usb/common/debug.c file. These moved functions include: dwc3_decode_get_status dwc3_decode_set_clear_feature dwc3_decode_set_address dwc3_decode_get_set_descriptor dwc3_decode_get_configuration dwc3_decode_set_configuration dwc3_decode_get_intf dwc3_decode_set_intf dwc3_decode_synch_frame dwc3_decode_set_sel dwc3_decode_set_isoch_delay dwc3_decode_ctrl These functions are used also in inroduced cdns3 driver. All functions prefixes were changed from dwc3 to usb. Also, function's parameters has been extended according to the name of fields in standard SETUP packet. Additionally, patch adds usb_decode_ctrl function to include/linux/usb/ch9.h file. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-29dt-bindings: add binding for USBSS-DRD controller.Pawel Laszczak1-0/+45
This patch aim at documenting USB related dt-bindings for the Cadence USBSS-DRD controller. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: gadget: composite: Set recommended BESL valuesThinh Nguyen2-12/+28
Set the recommended BESL deep and baseline values based on the gadget's configuration parameters to the extended BOS descriptor. This feature helps to optimize power savings by maximizing the opportunity for longer L1 residency time. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: gadget: Set BESL config parameterThinh Nguyen1-0/+10
When operating with LPM signals, the controller asserts the deep low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal (utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL to 0 for the shallow low-power signal. This maximizes the opportunity for L1 residency and optimizes power savings. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: Separate field holding multiple propertiesThinh Nguyen2-3/+3
dwc->hird_threshold field should store "snps,hird_threshold" property only and not a combination of multiple properties. Remove the value of "snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: gadget: Export recommended BESL valuesThinh Nguyen1-0/+3
Currently there's no option for the controller driver to report the recommended Best Effort Service Latency (BESL) when operating with LPM support. Add new fields in usb_dcd_config_params to export the recommended baseline and deep BESL values for the function drivers to set the proper BESL value in the BOS descriptor. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constantNishka Dasgupta1-1/+1
Static structure fsl_otg_initdata, of type fsl_otg_config, is used only once, when the value of its field otg_port is assigned to another variable. As fsl_otg_initdata.otg_port is of type u8, any changes to its copy do not affect the original, and fsl_otg_initdata itself is never modified. Hence make fsl_otg_initdata constant to protect it from unintended modification. Issue found with Coccinelle. Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: udc: lpc32xx: silence fall-through warningGustavo A. R. Silva1-1/+1
Silence the following fall-through warning by adding a break statement: drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disablesNeil Armstrong1-1/+13
When going in suspend, in Device mode, then resuming back leads to the following: unbalanced disables for USB_PWR_EN WARNING: CPU: 0 PID: 163 at ../drivers/regulator/core.c:2590 _regulator_disable+0x104/0x180 Hardware name: Amlogic Meson G12A U200 Development Board (DT) [...] pc : _regulator_disable+0x104/0x180 lr : _regulator_disable+0x104/0x180 [...] Call trace: _regulator_disable+0x104/0x180 regulator_disable+0x40/0x78 dwc3_meson_g12a_otg_mode_set+0x84/0xb0 dwc3_meson_g12a_irq_thread+0x58/0xb8 irq_thread_fn+0x28/0x80 irq_thread+0x118/0x1b8 kthread+0xf4/0x120 ret_from_fork+0x10/0x18 This disables the regulator if enabled on suspend, and the reverse on resume. Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Tested-by: Kevin Hilman <khilman@baylibre.com> Reported-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: udc: lpc32xx: remove set but not used 3 variablesMao Wenan1-6/+3
Fixes gcc '-Wunused-but-set-variable' warning: drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_protocol_cmd_r’: drivers/usb/gadget/udc/lpc32xx_udc.c:744:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable] drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_dma_ep’: drivers/usb/gadget/udc/lpc32xx_udc.c:1994:14: warning: variable ‘epstatus’ set but not used [-Wunused-but-set-variable] drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_ep0_setup’: drivers/usb/gadget/udc/lpc32xx_udc.c:2200:22: warning: variable ‘wLength’ set but not used [-Wunused-but-set-variable] It is not used since commit 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending ↵Roger Quadros1-1/+1
driver fails If a gadget driver is in the pending drivers list, a UDC becomes available and udc_bind_to_driver() fails, then it gets deleted from the pending list. i.e. list_del(&driver->pending) in check_pending_gadget_drivers(). Then if that gadget driver is unregistered, usb_gadget_unregister_driver() does a list_del(&driver->pending) again thus causing a page fault as that list entry has been poisoned by the previous list_del(). Fix this by using list_del_init() instead of list_del() in check_pending_gadget_drivers(). Test case: - Make sure no UDC is available - modprobe g_mass_storage file=wrongfile - Load UDC driver so it becomes available lun0: unable to open backing file: wrongfile - modprobe -r g_mass_storage [ 60.900431] Unable to handle kernel paging request at virtual address dead000000000108 [ 60.908346] Mem abort info: [ 60.911145] ESR = 0x96000044 [ 60.914227] Exception class = DABT (current EL), IL = 32 bits [ 60.920162] SET = 0, FnV = 0 [ 60.923217] EA = 0, S1PTW = 0 [ 60.926354] Data abort info: [ 60.929228] ISV = 0, ISS = 0x00000044 [ 60.933058] CM = 0, WnR = 1 [ 60.936011] [dead000000000108] address between user and kernel address ranges [ 60.943136] Internal error: Oops: 96000044 [#1] PREEMPT SMP [ 60.948691] Modules linked in: g_mass_storage(-) usb_f_mass_storage libcomposite xhci_plat_hcd xhci_hcd usbcore ti_am335x_adc kfifo_buf omap_rng cdns3 rng_core udc_core crc32_ce xfrm_user crct10dif_ce snd_so6 [ 60.993995] Process modprobe (pid: 834, stack limit = 0x00000000c2aebc69) [ 61.000765] CPU: 0 PID: 834 Comm: modprobe Not tainted 4.19.59-01963-g065f42a60499 #92 [ 61.008658] Hardware name: Texas Instruments SoC (DT) [ 61.014472] pstate: 60000005 (nZCv daif -PAN -UAO) [ 61.019253] pc : usb_gadget_unregister_driver+0x7c/0x108 [udc_core] [ 61.025503] lr : usb_gadget_unregister_driver+0x30/0x108 [udc_core] [ 61.031750] sp : ffff00001338fda0 [ 61.035049] x29: ffff00001338fda0 x28: ffff800846d40000 [ 61.040346] x27: 0000000000000000 x26: 0000000000000000 [ 61.045642] x25: 0000000056000000 x24: 0000000000000800 [ 61.050938] x23: ffff000008d7b0d0 x22: ffff0000088b07c8 [ 61.056234] x21: ffff000001100000 x20: ffff000002020260 [ 61.061530] x19: ffff0000010ffd28 x18: 0000000000000000 [ 61.066825] x17: 0000000000000000 x16: 0000000000000000 [ 61.072121] x15: 0000000000000000 x14: 0000000000000000 [ 61.077417] x13: ffff000000000000 x12: ffffffffffffffff [ 61.082712] x11: 0000000000000030 x10: 7f7f7f7f7f7f7f7f [ 61.088008] x9 : fefefefefefefeff x8 : 0000000000000000 [ 61.093304] x7 : ffffffffffffffff x6 : 000000000000ffff [ 61.098599] x5 : 8080000000000000 x4 : 0000000000000000 [ 61.103895] x3 : ffff000001100020 x2 : ffff800846d40000 [ 61.109190] x1 : dead000000000100 x0 : dead000000000200 [ 61.114486] Call trace: [ 61.116922] usb_gadget_unregister_driver+0x7c/0x108 [udc_core] [ 61.122828] usb_composite_unregister+0x10/0x18 [libcomposite] [ 61.128643] msg_cleanup+0x18/0xfce0 [g_mass_storage] [ 61.133682] __arm64_sys_delete_module+0x17c/0x1f0 [ 61.138458] el0_svc_common+0x90/0x158 [ 61.142192] el0_svc_handler+0x2c/0x80 [ 61.145926] el0_svc+0x8/0xc [ 61.148794] Code: eb03003f d10be033 54ffff21 a94d0281 (f9000420) [ 61.154869] ---[ end trace afb22e9b637bd9a7 ]--- Segmentation fault Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: st: Add of_dev_put() in probe functionNishka Dasgupta1-0/+1
In function st_dwc3_probe, variable child_pdev takes the value returned by of_find_device_by_node, which gets a device pointer but does not put it. If child_pdev is not put before the probe function returns, it may cause a reference leak. Hence put child_pdev after its last usage. Issue found with Coccinelle. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: st: Add of_node_put() before return in probe functionNishka Dasgupta1-3/+6
The local variable child in the function st_dwc3_probe takes the return value of of_get_child_by_name, which gets a node and does not put it. If the function returns without releasing child, this could cause a memory error. Hence put child as soon as there is no more use for it. Also create a new label, err_node_put, just before label undo_softreset; so that err_node_put puts child. In between initialisation of child and its first put, modify all statements that go to undo_softreset to now go to err_node_put instead, from where they can fall through to undo_softreset. Issue found with Coccinelle. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-28usb: dwc3: don't set gadget->is_otg flagRoger Quadros1-1/+0
This reverts commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.") We don't yet support any of the OTG mechanisms (HNP/SRP/ADP) and are not setting gadget->otg_caps, so don't set gadget->is_otg flag. If we do then we end up publishing a OTG1.0 descriptor in the gadget descriptor which causes device enumeration to fail if we are connected to a host with CONFIG_USB_OTG enabled. Host side log without this patch [ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port [ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32 [ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd [ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port [ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32 [ 97.253606] usb usb1-port1: attempt power cycle [ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd [ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port [ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32 [ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd [ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port [ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32 [ 98.493532] usb usb1-port1: unable to enumerate USB device Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Implement dummy hub TT requestsBenjamin Herrenschmidt1-0/+6
We just accept them instead of stalling and return zeros on GetTTState. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: Add definitions for the USB2.0 hub TT requestsBenjamin Herrenschmidt1-0/+4
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Improve debugging when nukingBenjamin Herrenschmidt1-2/+4
When nuking requests, it's useful to display how many were actually nuked. It has proven handy when debugging issues where EP0 went in a wrong state. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Remove unused "suspended" flagBenjamin Herrenschmidt2-5/+0
The state bit in the hub is sufficient Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Rework the reset logicBenjamin Herrenschmidt1-31/+27
We had some dodgy code using the speed setting to decide whether a port reset would reset the device or just enable it. Instead, if the device is disabled and has a gadget attached, a reset will enable it. If it's already enabled, a reset will reset it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Check suspend/resume callback existenceBenjamin Herrenschmidt1-2/+2
.. before calling them Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Don't reject requests on suspended devicesBenjamin Herrenschmidt3-6/+11
A disconnect may just suspend the hub in absence of a physical disconnect detection. If we start rejecting requests, the mass storage function gets into a spin trying to requeue the same request for ever and hangs. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Fix EP0 stall handlingBenjamin Herrenschmidt2-16/+33
When stalling EP0, we need to wait for an ACK interrupt, otherwise we may get out of sync on the next setup packet data phase. Also we need to ignore the direction when processing that interrupt as the HW reports a potential mismatch. Implement this by adding a stall state to EP0. This fixes some reported issues with mass storage and some hosts. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Cleanup EP0 state on port resetBenjamin Herrenschmidt3-0/+13
Otherwise, we can have a stale state after a disconnect and reconnect causing errors on the first SETUP packet to the device. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-12usb: gadget: aspeed: Don't set port enable change bit on resetBenjamin Herrenschmidt1-1/+8
This bit should be only set when the port enable goes down, for example, on errors. Not when it gets set after a port reset. Some USB stacks seem to be sensitive to this and fails enumeration. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: Use clk_bulk_prepare_enable()Andrey Smirnov1-18/+5
Use clk_bulk_prepare_enable() and clk_bulk_disable_unprepare() to simplify code a bit. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Felipe Balbi <balbi@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: Use devres to get clocksAndrey Smirnov1-5/+2
Use devres to get clocks and drop explicit clock freeing. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Felipe Balbi <balbi@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: remove generic PHYs forwarding for XHCI deviceMarek Szyprowski1-18/+4
Commit 08f871a3aca2 ("usb: dwc3: host: convey the PHYs to xhci") added forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat device. However XHCI(-plat) driver never gained support for generic PHYs, thus the lookup added by that commit is never used. In meantime the commit d64ff406e51e ("usb: dwc3: use bus->sysdev for DMA configuration") incorrectly changed the device used for creating lookup, making the lookup useless and generic PHYs inaccessible from XHCI device. However since commit 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core") USB HCD already handles generic PHYs acquired from the HCD's 'sysdev', which in this case is DWC3 core device. This means that creating any custom lookup entries for XHCI driver is no longer needed and can be simply removed. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: Update soft-reset wait polling rateThinh Nguyen2-5/+20
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit will not be cleared until after all the internal clocks are synchronized during soft-reset. This may take a little more than 50ms. Set the polling rate at 20ms instead. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: omap: squash include/linux/platform_data/dwc3-omap.hMasahiro Yamada2-44/+6
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: Switch to use device_property_count_u32()Andy Shevchenko1-2/+1
Use use device_property_count_u32() directly, that makes code neater. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: gadget: pch_udc: Use dev_get_drvdataChuhong Yuan1-2/+1
Instead of using to_pci_dev + pci_get_drvdata, use dev_get_drvdata to make code simpler. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc2: Switch to use device_property_count_u32()Andy Shevchenko1-4/+1
Use use device_property_count_u32() directly, that makes code neater. Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: keystone: use devm_platform_ioremap_resource() to simplify codeYueHaibing1-3/+1
Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: omap: use devm_platform_ioremap_resource() to simplify codeYueHaibing1-3/+1
Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc3: meson-g12a: use devm_platform_ioremap_resource() to simplify codeYueHaibing1-3/+1
Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: dwc2: gadget: Fix kill_all_requests raceJohn Keeping1-4/+5
When a gadget is disabled, kill_all_requests() can be called simultaneously from both a user process via dwc2_hsotg_pullup() and from the interrupt handler if the hardware detects disconnection. Since we drop the lock in dwc2_hsotg_complete_request() in order to call the completion handler, this means that the list is modified concurrently and leads to an infinite loop in kill_all_requests(). Replace the foreach loop with a while-not-empty loop in order to remove the danger of this concurrent modification. Note: I observed this with threadirqs, I'm not sure if it can be triggered without threaded interrupts. Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09usb: gadget: atmel_usba_udc: Mark expected switch fall-throughGustavo A. R. Silva1-0/+1
Mark switch cases where we are expecting to fall through. This patch fixes the following warning (Building: at91_dt_defconfig arm): drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-09USB: gadget: udc: s3c2410_udc: Mark expected switch fall-throughsGustavo A. R. Silva1-0/+2
Mark switch cases where we are expecting to fall through. This patch fixes the following warning (Building: tct_hammer_defconfig arm): drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=] drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-08-04Linux 5.3-rc3Linus Torvalds1-1/+1
2019-08-04Merge tag 'tpmdd-next-20190805' of git://git.infradead.org/users/jjs/linux-tpmddLinus Torvalds4-24/+63
Pull tpm fixes from Jarkko Sakkinen: "Two bug fixes that did not make into my first pull request" * tag 'tpmdd-next-20190805' of git://git.infradead.org/users/jjs/linux-tpmdd: tpm: tpm_ibm_vtpm: Fix unallocated banks tpm: Fix null pointer dereference on chip register error path
2019-08-04Merge tag 'mtd/fixes-for-5.3-rc3' of ↵Linus Torvalds2-4/+13
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux Pull MTD fixes from Miquel Raynal: "NAND: - Fix Micron driver as some chips enable internal ECC correction during their discovery while they advertize they do not have any. Hyperbus: - Restrict the build to only ARM64 SoCs (and compile testing) which is what should have been done since the beginning. - Fix Kconfig issue by selection something instead of implying it" * tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: mtd: hyperbus: Add hardware dependency to AM654 driver mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies mtd: rawnand: micron: handle on-die "ECC-off" devices correctly
2019-08-05tpm: tpm_ibm_vtpm: Fix unallocated banksNayna Jain4-17/+47
The nr_allocated_banks and allocated banks are initialized as part of tpm_chip_register. Currently, this is done as part of auto startup function. However, some drivers, like the ibm vtpm driver, do not run auto startup during initialization. This results in uninitialized memory issue and causes a kernel panic during boot. This patch moves the pcr allocation outside the auto startup function into tpm_chip_register. This ensures that allocated banks are initialized in any case. Fixes: 879b589210a9 ("tpm: retrieve digest size of unknown algorithms with PCR read") Reported-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Nayna Jain <nayna@linux.ibm.com> Reviewed-by: Mimi Zohar <zohar@linux.ibm.com> Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Tested-by: Michal Suchánek <msuchanek@suse.de> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2019-08-05tpm: Fix null pointer dereference on chip register error pathMilan Broz1-7/+16
If clk_enable is not defined and chip initialization is canceled code hits null dereference. Easily reproducible with vTPM init fail: swtpm chardev --tpmstate dir=nonexistent_dir --tpm2 --vtpm-proxy BUG: kernel NULL pointer dereference, address: 00000000 ... Call Trace: tpm_chip_start+0x9d/0xa0 [tpm] tpm_chip_register+0x10/0x1a0 [tpm] vtpm_proxy_work+0x11/0x30 [tpm_vtpm_proxy] process_one_work+0x214/0x5a0 worker_thread+0x134/0x3e0 ? process_one_work+0x5a0/0x5a0 kthread+0xd4/0x100 ? process_one_work+0x5a0/0x5a0 ? kthread_park+0x90/0x90 ret_from_fork+0x19/0x24 Fixes: 719b7d81f204 ("tpm: introduce tpm_chip_start() and tpm_chip_stop()") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Milan Broz <gmazyland@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2019-08-04Merge tag 'powerpc-5.3-3' of ↵Linus Torvalds9-5/+53
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "Some more powerpc fixes for 5.3: - Wire up the new clone3 syscall. - A fix for the PAPR SCM nvdimm driver, to fix a crash when firmware gives us a device that's attached to a non-online NUMA node. - A fix for a boot failure on 32-bit with KASAN enabled. - Three fixes for implicit fall through warnings, some of which are errors for us due to -Werror. Thanks to: Aneesh Kumar K.V, Christophe Leroy, Kees Cook, Santosh Sivaraj, Stephen Rothwell" * tag 'powerpc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kasan: fix early boot failure on PPC32 drivers/macintosh/smu.c: Mark expected switch fall-through powerpc/spe: Mark expected switch fall-throughs powerpc/nvdimm: Pick nearby online node if the device node is not online powerpc/kvm: Fall through switch case explicitly powerpc: Wire up clone3 syscall
2019-08-04MAINTAINERS: Add Geert as Renesas SoC Co-MaintainerGeert Uytterhoeven1-0/+4
At the end of the v5.3 upstream kernel development cycle, Simon will be stepping down from his role as Renesas SoC maintainer. Starting with the v5.4 development cycle, Geert is taking over this role. Add Geert as a co-maintainer, and add his git repository and branch. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-08-04Merge tag 'kbuild-fixes-v5.3-2' of ↵Linus Torvalds7-43/+58
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - detect missing missing "WITH Linux-syscall-note" for uapi headers - fix needless rebuild when using Clang - fix false-positive cc-option in Kconfig when using Clang - avoid including corrupted .*.cmd files in the modpost stage - fix warning of 'make vmlinux' - fix {m,n,x,g}config to not generate the broken .config on the second save operation. - some trivial Makefile fixes * tag 'kbuild-fixes-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kconfig: Clear "written" flag to avoid data loss kbuild: Check for unknown options with cc-option usage in Kconfig and clang lib/raid6: fix unnecessary rebuild of vpermxor*.c kbuild: modpost: do not parse unnecessary rules for vmlinux modpost kbuild: modpost: remove unnecessary dependency for __modpost kbuild: modpost: handle KBUILD_EXTRA_SYMBOLS only for external modules kbuild: modpost: include .*.cmd files only when targets exist kbuild: initialize CLANG_FLAGS correctly in the top Makefile kbuild: detect missing "WITH Linux-syscall-note" for uapi headers
2019-08-04Merge tag 'safesetid-maintainers-correction-5.3-rc2' of ↵Linus Torvalds1-0/+6
git://github.com/micah-morton/linux Pull SafeSetID maintainer update from Micah Morton: "Add entry in MAINTAINERS file for SafeSetID LSM" * tag 'safesetid-maintainers-correction-5.3-rc2' of git://github.com/micah-morton/linux: Add entry in MAINTAINERS file for SafeSetID LSM
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-13 09:44:10 +0000