summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-11-26regulator: qcom-rpmh: Add support for SDX55Vinod Koul1-0/+31
Add support from RPMH regulators found in SDX55 platform Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20201126093018.1085594-2-vkoul@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-26regulator: dt-bindings: Add PMX55 compatiblesVinod Koul1-0/+2
Add PMX55 compatibles for PMIC found in SDX55 platform Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20201126093018.1085594-1-vkoul@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-26regulator: core: return zero for selectors lower than linear_min_selClaudiu Beznea2-6/+9
Selectors lower than linear_min_sel should not be considered invalid. Thus return zero in case _regulator_list_voltage(), regulator_list_hardware_vsel() or regulator_list_voltage_table() receives such selectors as argument. Fixes: bdcd1177578c ("regulator: core: validate selector against linear_min_sel") Reported-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1606325147-606-1-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-25regulator: mcp16502-regulator: fix spelling mistakeMichael Klein1-1/+1
Signed-off-by: Michael Klein <michael@fossekall.de> Link: https://lore.kernel.org/r/20201124183730.2250690-2-michael@fossekall.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-23regulator: add SCMI driverCristian Marussi3-0/+427
Add a simple regulator based on SCMI Voltage Domain Protocol. Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> ---- v6 --> v7 - add proper blank lines between semantic blocks - fix return value on error path of scmi_reg_is_enabled() - use generic Failure message on err path of info_get() - fix comment containing apostrophe v3 --> v4 - using of_match_full_name core regulator flag - avoid coccinelle falde complaints about pointer-sized allocations v2 --> v3 - remove multiple linear mappings support - removed duplicated voltage name printout - added a few comments - simplified return path in scmi_reg_set_voltage_sel() v1 --> v2 - removed duplicate regulator naming - removed redundant .get/set_voltage ops: only _sel variants implemented - removed condexpr on fail path to increase readability v0 --> v1 - fixed init_data constraint parsing - fixes for v5.8 (linear_range.h) - fixed commit message content and subject line format - factored out SCMI core specific changes to distinct patch - reworked Kconfig and Makefile to keep proper alphabetic order - fixed SPDX comment style - removed unneeded inline functions - reworked conditionals for legibility - fixed some return paths to properly report SCMI original errors codes - added some more descriptive error messages when fw returns invalid ranges - removed unneeded explicit devm_regulator_unregister from .remove() Link: https://lore.kernel.org/r/20201123202336.46701-4-cristian.marussi@arm.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-23dt-bindings: arm: remove optional properties for SCMI RegulatorsCristian Marussi1-10/+1
Remove optional properties bindings descriptions for SCMI Regulators. Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20201123202336.46701-2-cristian.marussi@arm.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-23Merge series "Add support for SCMIv3.0 Voltage Domain Protocol and ↵Mark Brown2-2/+9
SCMI-Regulator" from Cristian Marussi <cristian.marussi@arm.com>: Hi, this series introduces the support for the new SCMI Voltage Domain Protocol defined by the upcoming SCMIv3.0 specification, whose BETA release is available at [1]. Afterwards, a new generic SCMI Regulator driver is developed on top of the new SCMI VD Protocol. In V4 Patch 3/5 introduced a needed fix in Regulator framework to cope with generic named nodes. The series is currently based on for-next/scmi [2] on top of: commit b141fca08207 ("firmware: arm_scmi: Fix missing destroy_workqueue()") Any feedback welcome, Thanks, Cristian --- v5 --> v6 - reordered dt bindings patch - removed single field struct - reviewed args to scmi_init_voltage_levels() - allocating scmi_voltage_info_array contiguously v4 --> v5 - rebased - VD Protocol - removed inline - moved segmented intervals defines - fixed some macros complaints by checkpatch v3 --> v4 - DT bindings - using generic node names - listing explicitly subset of supported regulators bindings - SCMI Regulator - using of_match_full_name core regulator flag - avoid coccinelle false flag complaints - VD Protocol - avoid coccinelle false flag complaints - avoiding fixed size typing v2 --> v3 - DT bindings - avoid awkard examples based on _cpu/_gpu regulators - SCMI Regulator - remove multiple linear mappings support - removed duplicated voltage name printout - added a few comments - simplified return path in scmi_reg_set_voltage_sel() - VD Protocol - restrict segmented voltage domain descriptors to one triplet - removed unneeded inline - free allocated resources for invalid voltage domain - added __must_check to info_get voltage operations - added a few comments - removed fixed size typing from struct voltage_info v1 --> v2 - rebased on for-next/scmi v5.10 - DT bindings - removed any reference to negative voltages - SCMI Regulator - removed duplicate regulator naming - removed redundant .get/set_voltage ops: only _sel variants implemented - removed condexpr on fail path to increase readability - VD Protocol - fix voltage levels query loop to reload full cmd description between iterations as reported by Etienne Carriere - ensure transport rx buffer is properly sized calli scmi_reset_rx_to_maxsz between transfers [1]:https://developer.arm.com/documentation/den0056/c/ [2]:https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux.git/log/?h=for-next/scmi Cristian Marussi (5): firmware: arm_scmi: Add Voltage Domain Support firmware: arm_scmi: add SCMI Voltage Domain devname regulator: core: add of_match_full_name boolean flag dt-bindings: arm: add support for SCMI Regulators regulator: add SCMI driver .../devicetree/bindings/arm/arm,scmi.txt | 43 ++ drivers/firmware/arm_scmi/Makefile | 2 +- drivers/firmware/arm_scmi/common.h | 1 + drivers/firmware/arm_scmi/driver.c | 3 + drivers/firmware/arm_scmi/voltage.c | 380 ++++++++++++++++ drivers/regulator/Kconfig | 9 + drivers/regulator/Makefile | 1 + drivers/regulator/of_regulator.c | 8 +- drivers/regulator/scmi-regulator.c | 409 ++++++++++++++++++ include/linux/regulator/driver.h | 3 + include/linux/scmi_protocol.h | 64 +++ 11 files changed, 920 insertions(+), 3 deletions(-) create mode 100644 drivers/firmware/arm_scmi/voltage.c create mode 100644 drivers/regulator/scmi-regulator.c -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
2020-11-23regulator: as3722: Fix fall-through warnings for ClangGustavo A. R. Silva1-1/+2
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a fallthrough pseudo-keyword instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/c0efb81064f71837f19408f65b52d155103ee514.1605896059.git.gustavoars@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-23regulator: core: add of_match_full_name boolean flagCristian Marussi2-2/+9
During regulators registration, if .of_match and .regulators_node are defined as non-null strings in struct regulator_desc the core searches the DT subtree rooted at .regulators_node trying to match, at first, .of_match against the 'regulator-compatible' property and, then, falling back to use the name of the node itself to determine a good match. Property 'regulator-compatible', though, is now deprecated and falling back to match against the node name, works fine only as long as the involved nodes are named in an unique way across the searched subtree; if that's not the case, like when using <common-name>@<unit> style naming for properties indexed via 'reg' property (as advised by the standard), the above matching mechanism based on the simple common name will lead to multiple matches and the only viable alternative would be to properly define the now deprecated 'regulator-compatible' as the node full name, i.e. <common-name>@<unit>. In order to address this case without using such deprecated binding, define a new boolean flag .of_match_full_name in struct regulator_desc to force the core to match against the node full-name instead of the plain name. Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20201119191051.46363-4-cristian.marussi@arm.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-23Merge tag 'scmi-voltage-5.11' of ↵Mark Brown6-1/+492
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into regulator-5.11 SCMI voltage domain management protocol support for v5.11 SCMI v3.0 voltage domain protocol support to discover the voltage levels supported by the domains and to set/get the configuration and voltage level of any given domain.
2020-11-20firmware: arm_scmi: Add support to enumerated SCMI voltage domain deviceCristian Marussi1-0/+1
Add SCMI voltage domain device name to the core list of supported protocol devices so that it can be enumerated if the firmware supports it. Link: https://lore.kernel.org/r/20201119191051.46363-3-cristian.marussi@arm.com Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2020-11-20firmware: arm_scmi: Add voltage domain management protocol supportCristian Marussi5-1/+448
SCMI v3.0 introduces voltage domain protocol which provides commands to: - Discover the voltage levels supported by a domain - Get the configuration and voltage level of a domain - Set the configuration and voltage level of a domain Let us add support for the same. Link: https://lore.kernel.org/r/20201119191051.46363-2-cristian.marussi@arm.com Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2020-11-20dt-bindings: arm: Add support for SCMI RegulatorsCristian Marussi1-0/+43
Add devicetree bindings to support regulators based on SCMI Voltage Domain Protocol. Link: https://lore.kernel.org/r/20201119191051.46363-5-cristian.marussi@arm.com Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2020-11-13regulator: core: do not continue if selector matchClaudiu Beznea1-0/+3
Do not continue if selector has already been located. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605290164-11556-1-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13Merge series "regulator: mcp16502: add support for ramp delay" from Claudiu ↵Mark Brown3-23/+124
Beznea <claudiu.beznea@microchip.com>: Hi, This series adds support for ramp delay on mcp16502. It also adds some cleanup on mcp16502. Apart from that patches 1/6 fixes the selector validation in case the regulator::desc::linear_min_sel is not zero. Thank you, Claudiu Beznea Changes in v3: - fix compilation error in patch 5/6 Reported-by: kernel test robot <lkp@intel.com> Changes in v2: - rebase on top of regulator/for-next - checked 1/6 and 3/6 applies on top of regulator/for-5.10 Claudiu Beznea (6): regulator: core: validate selector against linear_min_sel regulator: core: do not continue if selector match regulator: mcp16502: add linear_min_sel regulator: mcp16502: adapt for get/set on other registers regulator: mcp16502: add support for ramp delay regulator: mcp16502: remove void documentation of struct mcp16502 drivers/regulator/core.c | 12 +++- drivers/regulator/helpers.c | 3 +- drivers/regulator/mcp16502.c | 135 ++++++++++++++++++++++++++++++++++++------- 3 files changed, 127 insertions(+), 23 deletions(-) -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
2020-11-13regulator: core: validate selector against linear_min_selClaudiu Beznea2-3/+9
There are regulators who's min selector is not zero. Selectors loops (looping b/w zero and regulator::desc::n_voltages) might throw errors because invalid selectors are used (lower than regulator::desc::linear_min_sel). For this situations validate selectors against regulator::desc::linear_min_sel. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605280870-32432-2-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13regulator: mcp16502: remove void documentation of struct mcp16502Claudiu Beznea1-2/+0
struct mcp16502 has no members called rdev or rmap. Remove the documentation. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605280870-32432-7-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13regulator: mcp16502: add support for ramp delayClaudiu Beznea1-2/+87
MCP16502 have configurable ramp delay support (via DVSR bits in regulators' CFG register). Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605280870-32432-6-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13regulator: mcp16502: adapt for get/set on other registersClaudiu Beznea1-16/+27
MCP16502 have multiple registers for each regulator (as described in enum mcp16502_reg). Adapt the code to be able to get/set all these registers. This is necessary for the following commits. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605280870-32432-5-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13regulator: mcp16502: add linear_min_selClaudiu Beznea1-0/+1
Selectors b/w zero and VDD_LOW_SEL are not valid. Use linear_min_sel. Fixes: 919261c03e7ca ("regulator: mcp16502: add regulator driver for MCP16502") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/1605280870-32432-4-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-13regulator: debug early supply resolvingMichał Mirosław1-0/+2
Help debugging the case when set_machine_constraints() needs to be repeated. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1 Link: https://lore.kernel.org/r/f9cba575580369e46661a9278ee6c6a8d8564c2a.1605226675.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-11Merge branch 'for-5.10' of ↵Mark Brown1-2/+5
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-5.11
2020-11-10Merge series "regulator: bd718x7: support voltage scaling" from Matti ↵Mark Brown816-31296/+7968
Vaittinen <matti.vaittinen@fi.rohmeurope.com>: RFC for adding a support for typical voltage scaling connection In few occasions there has been a need to scale the voltage output from bucks on BD71837. Usually this is done when buck8 is used to power specific GPU which can utilize voltages down to 0.7V. As lowest the buck8 on BD71837 can go is 0.8V, and external connection is used to scale the voltages. The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the feedback pin using suitable voltage/resistors. |---------------| | buck 8 |-------+----->Vout | | | |---------------| | | | | | +-------+--R2----+ | R1 | V FB-pull-up This will scale the voltage as follows: - Vout_o = Vo - (Vpu - Vo)*R2/R1 - Linear_step = step_orig*(R1+R2)/R1 where: Vout_o is adjusted voltage output at vsel reg value 0 Vo is original voltage output at vsel reg value 0 Vpu is the pull-up voltage V FB-pull-up in the picture R1 and R2 are resistor values. >From HW point of view this does not need to be limited to buck 8. This connection can be used to adjust output from any of the bucks on BD71837/47/50. As this seems to be a 'de-facto' way to scale the voltages on BD71837 it might be a good idea to support computing the new voltage ranges for bucks based on the V-pull-up and resistor R1/R2 values given from device-tree. This allows describing the external HW connection using DT to correctly scale the voltages. This RFC uses "rohm,feedback-pull-up-r1-ohms" and "rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but these names (without the picture) might not be too descriptive. I am grateful for all suggestions as better and more descriptive names. This patch series is an RFC because this connection feels somewhat "hacky". OTOH - when hack becomes widely used, it is less of an hack and more of a standard - and occasionally supporting HW hacks using SW may benefit us all, right? :) The other thing some projects do is allowing the change of BD71837 buck8 voltages when buck8 is enabled. This however will introduce voltage spikes as buck8 was not originally designed for this. The specific HW platform must be evaluated to be able to tolerate these spikes. Thus this patch series does not support buck8 voltage changes when buck8 is enabled. I wonder if this should be allowed per some config option(?) I don't want to help people frying their boards... Opinions? Is there suggested way of allowing this type of features at own risk? Config or even Some #ifdef which is not listed in Kconfig? Device-tree property? If you have (good) suggestions I could add the optional (non default) DVS support for non DVS bucks on BD71837. Matti Vaittinen (3): dt-bindings: regulator: BD71837 support commonly used feedback connection dt-bindings: regulator: BD71847 support commonly used feedback connection regulator: bd718x7: Support external connection to scale voltages .../regulator/rohm,bd71837-regulator.yaml | 48 +++++ .../regulator/rohm,bd71847-regulator.yaml | 49 ++++++ drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++- 3 files changed, 254 insertions(+), 7 deletions(-) base-commit: 3cea11cd5e3b00d91caf0b4730194039b45c5891 -- 2.21.3 -- Matti Vaittinen, Linux device drivers ROHM Semiconductors, Finland SWDC Kiviharjunlenkki 1E 90220 OULU FINLAND ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~ Simon says - in Latin please. ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~ Thanks to Simon Glass for the translation =]
2020-11-10regulator: bd718x7: Support external connection to scale voltagesMatti Vaittinen1-7/+157
Setups where regulator (especially the buck8) output voltage is scaled by adding external connection where some other regulator output is connected to feedback-pin (over suitable resistors) is getting popular amongst users of BD71837. This allows for example scaling down the buck8 voltages to suit lover GPU voltages for projects where buck8 is (ab)used to supply power for GPU. As a note - some setups do allow DVS for buck8. This do produce voltage spikes and the HW must be evaluated to be able to survive them. Thus this commit still keep the DVS disabled for non DVS bucks by default. Let's not help you burn your proto board. Allow describing this external connection from DT and scale the voltages accordingly. This is what the connection should look like: |------------| | buck 8 |-------+----->Vout | | | |------------| | | FB pin | | | +-------+--R2---+ | R1 | V FB-pull-up Here the buck output is sifted according to formula: Vout_o = Vo - (Vpu - Vo)*R2/R1 Linear_step = step_orig*(R1+R2)/R1 where: Vout_o is adjusted voltage output at vsel reg value 0 Vo is original voltage output at vsel reg value 0 Vpu is the pull-up voltage V FB-pull-up in the picture R1 and R2 are resistor values. Bring support for specifying the Vpu, R1 and R2 from device tree and scale voltages if they are given. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Link: https://lore.kernel.org/r/89b2be87074f307a8823f15f34e1f662023cbf36.1604994184.git.matti.vaittinen@fi.rohmeurope.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-10regulator: BD71847 support commonly used feedback connectionMatti Vaittinen1-0/+49
The BD71847 buck output voltages are in a few cases scaled using external connection which adds a pull-up to regulator feedback pin. This connection will adjust output voltage from regulator in a deterministic way. Add support for describing this HW connection so that driver can adjust voltage ranges accordingly. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Link: https://lore.kernel.org/r/9b6b3d8233071d478f7d1e93b498f5a2141941e6.1604994184.git.matti.vaittinen@fi.rohmeurope.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-10regulator: BD71837 support commonly used feedback connectionMatti Vaittinen1-0/+48
The BD71837 buck output voltages are in a few cases scaled using external connection which adds a pull-up to regulator feedback pin. This connection will adjust output voltage from regulator in a deterministic way. Add support for describing this HW connection so that driver can adjust voltage ranges accordingly. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Link: https://lore.kernel.org/r/9959924313db7c7165598604f9a07bf227f471a8.1604994184.git.matti.vaittinen@fi.rohmeurope.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-10regulator: core: don't disable regulator if is_enabled return error.Pi-Hsun Shih1-2/+3
In regulator_late_cleanup when is_enabled failed, don't try to disable the regulator since it would likely to fail too and causing confusing error messages. Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Link: https://lore.kernel.org/r/20201106064817.3290927-1-pihsun@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-09regulator: da9121: Use additionalPropertiesVincent Whitchurch1-1/+1
There's no $ref at the top level so use additionalProperties instead of unevaluatedProperties. This fixes the following warning with the latest dtschema: Documentation/devicetree/bindings/regulator/dlg,da9121.yaml: 'additionalProperties' is a required property Reported-by: Rob Herring <robh@kernel.org> Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20201109085438.16230-1-vincent.whitchurch@axis.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-03regulator: Add DA9121Vincent Whitchurch1-0/+47
Add bindings for the Dialog Semiconductor DA9121 voltage regulator. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20201103100021.19603-2-vincent.whitchurch@axis.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-03regulator: Add support for DA9121 regulatorVincent Whitchurch3-0/+121
Add support for the Dialog Semiconductor DA9121, a single-channel dual-phase buck converter controlled via I2C. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20201103100021.19603-3-vincent.whitchurch@axis.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-03regulator: defer probe when trying to get voltage from unresolved supplyMichał Mirosław1-0/+2
regulator_get_voltage_rdev() is called in regulator probe() when applying machine constraints. The "fixed" commit exposed the problem that non-bypassed regulators can forward the request to its parent (like bypassed ones) supply. Return -EPROBE_DEFER when the supply is expected but not resolved yet. Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator") Cc: stable@vger.kernel.org Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reported-by: Ondřej Jirman <megous@megous.com> Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Ondřej Jirman <megous@megous.com> Link: https://lore.kernel.org/r/a9041d68b4d35e4a2dd71629c8a6422662acb5ee.1604351936.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org>
2020-11-01Linux 5.10-rc2Linus Torvalds1-1/+1
2020-11-01Merge tag 'x86-urgent-2020-11-01' of ↵Linus Torvalds1-13/+30
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "Three fixes all related to #DB: - Handle the BTF bit correctly so it doesn't get lost due to a kernel #DB - Only clear and set the virtual DR6 value used by ptrace on user space triggered #DB. A kernel #DB must leave it alone to ensure data consistency for ptrace. - Make the bitmasking of the virtual DR6 storage correct so it does not lose DR_STEP" * tag 'x86-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/debug: Fix DR_STEP vs ptrace_get_debugreg(6) x86/debug: Only clear/set ->virtual_dr6 for userspace #DB x86/debug: Fix BTF handling
2020-11-01Merge tag 'timers-urgent-2020-11-01' of ↵Linus Torvalds5-16/+6
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer fixes from Thomas Gleixner: "A few fixes for timers/timekeeping: - Prevent undefined behaviour in the timespec64_to_ns() conversion which is used for converting user supplied time input to nanoseconds. It lacked overflow protection. - Mark sched_clock_read_begin/retry() to prevent recursion in the tracer - Remove unused debug functions in the hrtimer and timerlist code" * tag 'timers-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: time: Prevent undefined behaviour in timespec64_to_ns() timers: Remove unused inline funtion debug_timer_free() hrtimer: Remove unused inline function debug_hrtimer_free() time/sched_clock: Mark sched_clock_read_begin/retry() as notrace
2020-11-01Merge tag 'smp-urgent-2020-11-01' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull smp fix from Thomas Gleixner: "A single fix for stop machine. Mark functions no trace to prevent a crash caused by recursion when enabling or disabling a tracer on RISC-V (probably all architectures which patch through stop machine)" * tag 'smp-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: stop_machine, rcu: Mark functions as notrace
2020-11-01Merge tag 'locking-urgent-2020-11-01' of ↵Linus Torvalds2-14/+10
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking fixes from Thomas Gleixner: "A couple of locking fixes: - Fix incorrect failure injection handling in the fuxtex code - Prevent a preemption warning in lockdep when tracking local_irq_enable() and interrupts are already enabled - Remove more raw_cpu_read() usage from lockdep which causes state corruption on !X86 architectures. - Make the nr_unused_locks accounting in lockdep correct again" * tag 'locking-urgent-2020-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: lockdep: Fix nr_unused_locks accounting locking/lockdep: Remove more raw_cpu_read() usage futex: Fix incorrect should_fail_futex() handling lockdep: Fix preemption WARN for spurious IRQ-enable
2020-11-01Merge tag 'char-misc-5.10-rc2' of ↵Linus Torvalds95-26793/+34
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc fixes/removals from Greg KH: "Here's some small fixes for 5.10-rc2 and a big driver removal. The fixes are for some reported issues in the interconnect and coresight drivers, nothing major. The "big" driver removal is the MIC drivers have been asked to be removed as the hardware never shipped and Intel no longer wants to maintain something that no one can use. This is welcomed by many as the DMA usage of these drivers was "interesting" and the security people were starting to question some issues that were starting to be found in the codebase. Note, one of the subsystems for this driver, the "VOP" code, will probably come back in future kernel versions as it was looking to potentially solve some PCIe virtualization issues that a number of other vendors were wanting to solve. But as-is, this codebase didn't work for anyone else so no actual functionality is being removed. All of these have been in linux-next with no reported issues" * tag 'char-misc-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: coresight: cti: Initialize dynamic sysfs attributes coresight: Fix uninitialised pointer bug in etm_setup_aux() coresight: add module license misc: mic: remove the MIC drivers interconnect: qcom: use icc_sync state for sm8[12]50 interconnect: qcom: Ensure that the floor bandwidth value is enforced interconnect: qcom: sc7180: Init BCMs before creating the nodes interconnect: qcom: sdm845: Init BCMs before creating the nodes interconnect: Aggregate before setting initial bandwidth interconnect: qcom: sdm845: Enable keepalive for the MM1 BCM
2020-11-01Merge tag 'driver-core-5.10-rc2' of ↵Linus Torvalds250-2493/+4134
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core and documentation fixes from Greg KH: "Here is one tiny debugfs change to fix up an API where the last user was successfully fixed up in 5.10-rc1 (so it couldn't be merged earlier), and a much larger Documentation/ABI/ update to the files so they can be automatically parsed by our tools. The Documentation/ABI/ updates are just formatting issues, small ones to bring the files into parsable format, and have been acked by numerous subsystem maintainers and the documentation maintainer. I figured it was good to get this into 5.10-rc2 to help wih the merge issues that would arise if these were to stick in linux-next until 5.11-rc1. The debugfs change has been in linux-next for a long time, and the Documentation updates only for the last linux-next release" * tag 'driver-core-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (40 commits) scripts: get_abi.pl: assume ReST format by default docs: ABI: sysfs-class-led-trigger-pattern: remove hw_pattern duplication docs: ABI: sysfs-class-backlight: unify ABI documentation docs: ABI: sysfs-c2port: remove a duplicated entry docs: ABI: sysfs-class-power: unify duplicated properties docs: ABI: unify /sys/class/leds/<led>/brightness documentation docs: ABI: stable: remove a duplicated documentation docs: ABI: change read/write attributes docs: ABI: cleanup several ABI documents docs: ABI: sysfs-bus-nvdimm: use the right format for ABI docs: ABI: vdso: use the right format for ABI docs: ABI: fix syntax to be parsed using ReST notation docs: ABI: convert testing/configfs-acpi to ReST docs: Kconfig/Makefile: add a check for broken ABI files docs: abi-testing.rst: enable --rst-sources when building docs docs: ABI: don't escape ReST-incompatible chars from obsolete and removed docs: ABI: create a 2-depth index for ABI docs: ABI: make it parse ABI/stable as ReST-compatible files docs: ABI: sysfs-uevent: make it compatible with ReST output docs: ABI: testing: make the files compatible with ReST output ...
2020-11-01Merge tag 'staging-5.10-rc2' of ↵Linus Torvalds8-30/+49
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver fixes from Greg KH: "Here are some small staging driver fixes for issues that have been reported in 5.10-rc1: - octeon driver fixes - wfx driver fixes - memory leak fix in vchiq driver - fieldbus driver bugfix - comedi driver bugfix All of these have been in linux-next with no reported issues" * tag 'staging-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: fieldbus: anybuss: jump to correct label in an error path staging: wfx: fix test on return value of gpiod_get_value() staging: wfx: fix use of uninitialized pointer staging: mmal-vchiq: Fix memory leak for vchiq_instance staging: comedi: cb_pcidas: Allow 2-channel commands for AO subdevice staging: octeon: Drop on uncorrectable alignment or FCS error staging: octeon: repair "fixed-link" support
2020-11-01Merge tag 'tty-5.10-rc2' of ↵Linus Torvalds4-38/+37
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are some small TTY and Serial driver fixes for reported issues for 5.10-rc2. They include: - vt ioctl bugfix for reported problems - fsl_lpuart serial driver fix - 21285 serial driver bugfix All have been in linux-next with no reported issues" * tag 'tty-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: vt_ioctl: fix GIO_UNIMAP regression vt: keyboard, extend func_buf_lock to readers vt: keyboard, simplify vt_kdgkbsent tty: serial: fsl_lpuart: LS1021A has a FIFO size of 16 words, like LS1028A tty: serial: 21285: fix lockup on open
2020-11-01Merge tag 'usb-5.10-rc2' of ↵Linus Torvalds22-138/+195
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB driver fixes from Greg KH: "Here are a number of small bugfixes for reported issues in some USB drivers. They include: - typec bugfixes - xhci bugfixes and lockdep warning fixes - cdc-acm driver regression fix - kernel doc fixes - cdns3 driver bugfixes for a bunch of reported issues - other tiny USB driver fixes All have been in linux-next with no reported issues" * tag 'usb-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: cdns3: gadget: own the lock wrongly at the suspend routine usb: cdns3: Fix on-chip memory overflow issue usb: cdns3: gadget: suspicious implicit sign extension xhci: Don't create stream debugfs files with spinlock held. usb: xhci: Workaround for S3 issue on AMD SNPS 3.0 xHC xhci: Fix sizeof() mismatch usb: typec: stusb160x: fix signedness comparison issue with enum variables usb: typec: add missing MODULE_DEVICE_TABLE() to stusb160x USB: apple-mfi-fastcharge: don't probe unhandled devices usbcore: Check both id_table and match() when both available usb: host: ehci-tegra: Fix error handling in tegra_ehci_probe() usb: typec: stusb160x: fix an IS_ERR() vs NULL check in probe usb: typec: tcpm: reset hard_reset_count for any disconnect usb: cdc-acm: fix cooldown mechanism usb: host: fsl-mph-dr-of: check return of dma_set_mask() usb: fix kernel-doc markups usb: typec: stusb160x: fix some signedness bugs usb: cdns3: Variable 'length' set but not used
2020-11-01Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds26-76/+306
Pull kvm fixes from Paolo Bonzini: "ARM: - selftest fix - force PTE mapping on device pages provided via VFIO - fix detection of cacheable mapping at S2 - fallback to PMD/PTE mappings for composite huge pages - fix accounting of Stage-2 PGD allocation - fix AArch32 handling of some of the debug registers - simplify host HYP entry - fix stray pointer conversion on nVHE TLB invalidation - fix initialization of the nVHE code - simplify handling of capabilities exposed to HYP - nuke VCPUs caught using a forbidden AArch32 EL0 x86: - new nested virtualization selftest - miscellaneous fixes - make W=1 fixes - reserve new CPUID bit in the KVM leaves" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: vmx: remove unused variable KVM: selftests: Don't require THP to run tests KVM: VMX: eVMCS: make evmcs_sanitize_exec_ctrls() work again KVM: selftests: test behavior of unmapped L2 APIC-access address KVM: x86: Fix NULL dereference at kvm_msr_ignored_check() KVM: x86: replace static const variables with macros KVM: arm64: Handle Asymmetric AArch32 systems arm64: cpufeature: upgrade hyp caps to final arm64: cpufeature: reorder cpus_have_{const, final}_cap() KVM: arm64: Factor out is_{vhe,nvhe}_hyp_code() KVM: arm64: Force PTE mapping on fault resulting in a device mapping KVM: arm64: Use fallback mapping sizes for contiguous huge page sizes KVM: arm64: Fix masks in stage2_pte_cacheable() KVM: arm64: Fix AArch32 handling of DBGD{CCINT,SCRext} and DBGVCR KVM: arm64: Allocate stage-2 pgd pages with GFP_KERNEL_ACCOUNT KVM: arm64: Drop useless PAN setting on host EL1 to EL2 transition KVM: arm64: Remove leftover kern_hyp_va() in nVHE TLB invalidation KVM: arm64: Don't corrupt tpidr_el2 on failed HVC call x86/kvm: Reserve KVM_FEATURE_MSI_EXT_DEST_ID
2020-10-31Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds6-82/+157
Pull vhost fixes from Michael Tsirkin: "Fixes all over the place. A new UAPI is borderline: can also be considered a new feature but also seems to be the only way we could come up with to fix addressing for userspace - and it seems important to switch to it now before userspace making assumptions about addressing ability of devices is set in stone" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: vdpasim: allow to assign a MAC address vdpasim: fix MAC address configuration vdpa: handle irq bypass register failure case vdpa_sim: Fix DMA mask Revert "vhost-vdpa: fix page pinning leakage in error path" vdpa/mlx5: Fix error return in map_direct_mr() vhost_vdpa: Return -EFAULT if copy_from_user() fails vdpa_sim: implement get_iova_range() vhost: vdpa: report iova range vdpa: introduce config op to get valid iova range
2020-10-31Merge tag 'flexible-array-conversions-5.10-rc2' of ↵Linus Torvalds23-40/+40
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux Pull more flexible-array member conversions from Gustavo A. R. Silva: "Replace zero-length arrays with flexible-array members" * tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: printk: ringbuffer: Replace zero-length array with flexible-array member net/smc: Replace zero-length array with flexible-array member net/mlx5: Replace zero-length array with flexible-array member mei: hw: Replace zero-length array with flexible-array member gve: Replace zero-length array with flexible-array member Bluetooth: btintel: Replace zero-length array with flexible-array member scsi: target: tcmu: Replace zero-length array with flexible-array member ima: Replace zero-length array with flexible-array member enetc: Replace zero-length array with flexible-array member fs: Replace zero-length array with flexible-array member Bluetooth: Replace zero-length array with flexible-array member params: Replace zero-length array with flexible-array member tracepoint: Replace zero-length array with flexible-array member platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
2020-10-31Merge tag 'dma-mapping-5.10-2' of git://git.infradead.org/users/hch/dma-mappingLinus Torvalds1-3/+3
Pull dma-mapping fix from Christoph Hellwig: "Fix an integer overflow on 32-bit platforms in the new DMA range code (Geert Uytterhoeven)" * tag 'dma-mapping-5.10-2' of git://git.infradead.org/users/hch/dma-mapping: dma-mapping: fix 32-bit overflow with CONFIG_ARM_LPAE=n
2020-10-31Merge tag 'scsi-fixes' of ↵Linus Torvalds5-21/+43
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Four driver fixes and one core fix. The core fix closes a race window where we could kick off a second asynchronous scan because the test and set of the variable preventing it isn't atomic" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: hisi_sas: Stop using queue #0 always for v2 hw scsi: ibmvscsi: Fix potential race after loss of transport scsi: mptfusion: Fix null pointer dereferences in mptscsih_remove() scsi: qla2xxx: Return EBUSY on fcport deletion scsi: core: Don't start concurrent async scan on same host
2020-10-31KVM: vmx: remove unused variablePaolo Bonzini1-2/+0
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-10-31KVM: selftests: Don't require THP to run testsAndrew Jones1-7/+16
Unless we want to test with THP, then we shouldn't require it to be configured by the host kernel. Unfortunately, even advising with MADV_NOHUGEPAGE does require it, so check for THP first in order to avoid madvise failing with EINVAL. Signed-off-by: Andrew Jones <drjones@redhat.com> Message-Id: <20201029201703.102716-2-drjones@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-10-31KVM: VMX: eVMCS: make evmcs_sanitize_exec_ctrls() work againVitaly Kuznetsov3-5/+5
It was noticed that evmcs_sanitize_exec_ctrls() is not being executed nowadays despite the code checking 'enable_evmcs' static key looking correct. Turns out, static key magic doesn't work in '__init' section (and it is unclear when things changed) but setup_vmcs_config() is called only once per CPU so we don't really need it to. Switch to checking 'enlightened_vmcs' instead, it is supposed to be in sync with 'enable_evmcs'. Opportunistically make evmcs_sanitize_exec_ctrls '__init' and drop unneeded extra newline from it. Reported-by: Yang Weijiang <weijiang.yang@intel.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Message-Id: <20201014143346.2430936-1-vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-10-31KVM: selftests: test behavior of unmapped L2 APIC-access addressJim Mattson5-0/+159
Add a regression test for commit 671ddc700fd0 ("KVM: nVMX: Don't leak L1 MMIO regions to L2"). First, check to see that an L2 guest can be launched with a valid APIC-access address that is backed by a page of L1 physical memory. Next, set the APIC-access address to a (valid) L1 physical address that is not backed by memory. KVM can't handle this situation, so resuming L2 should result in a KVM exit for internal error (emulation). Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Ricardo Koller <ricarkol@google.com> Reviewed-by: Peter Shier <pshier@google.com> Message-Id: <20201026180922.3120555-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-14 06:52:25 +0000