diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c | 16 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/norm_desc.c | 16 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 32 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 10 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 91 |
5 files changed, 100 insertions, 65 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c index f0d797ab74d8..44022b1845ce 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c @@ -34,6 +34,9 @@ #define SYSMGR_EMACGRP_CTRL_PHYSEL_MASK 0x00000003 #define SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK 0x00000010 +#define SYSMGR_FPGAGRP_MODULE_REG 0x00000028 +#define SYSMGR_FPGAGRP_MODULE_EMAC 0x00000004 + #define EMAC_SPLITTER_CTRL_REG 0x0 #define EMAC_SPLITTER_CTRL_SPEED_MASK 0x3 #define EMAC_SPLITTER_CTRL_SPEED_10 0x2 @@ -148,7 +151,7 @@ static int socfpga_dwmac_setup(struct socfpga_dwmac *dwmac) int phymode = dwmac->interface; u32 reg_offset = dwmac->reg_offset; u32 reg_shift = dwmac->reg_shift; - u32 ctrl, val; + u32 ctrl, val, module; switch (phymode) { case PHY_INTERFACE_MODE_RGMII: @@ -175,12 +178,19 @@ static int socfpga_dwmac_setup(struct socfpga_dwmac *dwmac) ctrl &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << reg_shift); ctrl |= val << reg_shift; - if (dwmac->f2h_ptp_ref_clk) + if (dwmac->f2h_ptp_ref_clk) { ctrl |= SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK << (reg_shift / 2); - else + regmap_read(sys_mgr_base_addr, SYSMGR_FPGAGRP_MODULE_REG, + &module); + module |= (SYSMGR_FPGAGRP_MODULE_EMAC << (reg_shift / 2)); + regmap_write(sys_mgr_base_addr, SYSMGR_FPGAGRP_MODULE_REG, + module); + } else { ctrl &= ~(SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK << (reg_shift / 2)); + } regmap_write(sys_mgr_base_addr, reg_offset, ctrl); + return 0; } diff --git a/drivers/net/ethernet/stmicro/stmmac/norm_desc.c b/drivers/net/ethernet/stmicro/stmmac/norm_desc.c index e13228f115f0..011386f6f24d 100644 --- a/drivers/net/ethernet/stmicro/stmmac/norm_desc.c +++ b/drivers/net/ethernet/stmicro/stmmac/norm_desc.c @@ -199,11 +199,6 @@ static void ndesc_prepare_tx_desc(struct dma_desc *p, int is_fs, int len, { unsigned int tdes1 = p->des1; - if (mode == STMMAC_CHAIN_MODE) - norm_set_tx_desc_len_on_chain(p, len); - else - norm_set_tx_desc_len_on_ring(p, len); - if (is_fs) tdes1 |= TDES1_FIRST_SEGMENT; else @@ -217,10 +212,15 @@ static void ndesc_prepare_tx_desc(struct dma_desc *p, int is_fs, int len, if (ls) tdes1 |= TDES1_LAST_SEGMENT; - if (tx_own) - tdes1 |= TDES0_OWN; - p->des1 = tdes1; + + if (mode == STMMAC_CHAIN_MODE) + norm_set_tx_desc_len_on_chain(p, len); + else + norm_set_tx_desc_len_on_ring(p, len); + + if (tx_own) + p->des0 |= TDES0_OWN; } static void ndesc_set_tx_ic(struct dma_desc *p) diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 4c5ce9848ca9..fcbd4be562e2 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -278,7 +278,6 @@ static void stmmac_eee_ctrl_timer(unsigned long arg) */ bool stmmac_eee_init(struct stmmac_priv *priv) { - char *phy_bus_name = priv->plat->phy_bus_name; unsigned long flags; bool ret = false; @@ -289,10 +288,6 @@ bool stmmac_eee_init(struct stmmac_priv *priv) (priv->pcs == STMMAC_PCS_RTBI)) goto out; - /* Never init EEE in case of a switch is attached */ - if (phy_bus_name && (!strcmp(phy_bus_name, "fixed"))) - goto out; - /* MAC core supports the EEE feature. */ if (priv->dma_cap.eee) { int tx_lpi_timer = priv->tx_lpi_timer; @@ -772,10 +767,16 @@ static void stmmac_adjust_link(struct net_device *dev) spin_unlock_irqrestore(&priv->lock, flags); - /* At this stage, it could be needed to setup the EEE or adjust some - * MAC related HW registers. - */ - priv->eee_enabled = stmmac_eee_init(priv); + if (phydev->is_pseudo_fixed_link) + /* Stop PHY layer to call the hook to adjust the link in case + * of a switch is attached to the stmmac driver. + */ + phydev->irq = PHY_IGNORE_INTERRUPT; + else + /* At this stage, init the EEE if supported. + * Never called in case of fixed_link. + */ + priv->eee_enabled = stmmac_eee_init(priv); } /** @@ -827,12 +828,8 @@ static int stmmac_init_phy(struct net_device *dev) phydev = of_phy_connect(dev, priv->plat->phy_node, &stmmac_adjust_link, 0, interface); } else { - if (priv->plat->phy_bus_name) - snprintf(bus_id, MII_BUS_ID_SIZE, "%s-%x", - priv->plat->phy_bus_name, priv->plat->bus_id); - else - snprintf(bus_id, MII_BUS_ID_SIZE, "stmmac-%x", - priv->plat->bus_id); + snprintf(bus_id, MII_BUS_ID_SIZE, "stmmac-%x", + priv->plat->bus_id); snprintf(phy_id_fmt, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, bus_id, priv->plat->phy_addr); @@ -870,11 +867,6 @@ static int stmmac_init_phy(struct net_device *dev) return -ENODEV; } - /* If attached to a switch, there is no reason to poll phy handler */ - if (priv->plat->phy_bus_name) - if (!strcmp(priv->plat->phy_bus_name, "fixed")) - phydev->irq = PHY_IGNORE_INTERRUPT; - pr_debug("stmmac_init_phy: %s: attached to PHY (UID 0x%x)" " Link = %d\n", dev->name, phydev->phy_id, phydev->link); diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c index ea76129dafc2..06704ca6f9ca 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c @@ -198,20 +198,12 @@ int stmmac_mdio_register(struct net_device *ndev) struct mii_bus *new_bus; struct stmmac_priv *priv = netdev_priv(ndev); struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data; - int addr, found; struct device_node *mdio_node = priv->plat->mdio_node; + int addr, found; if (!mdio_bus_data) return 0; - if (IS_ENABLED(CONFIG_OF)) { - if (mdio_node) { - netdev_dbg(ndev, "FOUND MDIO subnode\n"); - } else { - netdev_warn(ndev, "No MDIO subnode found\n"); - } - } - new_bus = mdiobus_alloc(); if (new_bus == NULL) return -ENOMEM; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c index dcbd2a1601e8..cf37ea558ecc 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c @@ -132,6 +132,69 @@ static struct stmmac_axi *stmmac_axi_setup(struct platform_device *pdev) } /** + * stmmac_dt_phy - parse device-tree driver parameters to allocate PHY resources + * @plat: driver data platform structure + * @np: device tree node + * @dev: device pointer + * Description: + * The mdio bus will be allocated in case of a phy transceiver is on board; + * it will be NULL if the fixed-link is configured. + * If there is the "snps,dwmac-mdio" sub-node the mdio will be allocated + * in any case (for DSA, mdio must be registered even if fixed-link). + * The table below sums the supported configurations: + * ------------------------------- + * snps,phy-addr | Y + * ------------------------------- + * phy-handle | Y + * ------------------------------- + * fixed-link | N + * ------------------------------- + * snps,dwmac-mdio | + * even if | Y + * fixed-link | + * ------------------------------- + * + * It returns 0 in case of success otherwise -ENODEV. + */ +static int stmmac_dt_phy(struct plat_stmmacenet_data *plat, + struct device_node *np, struct device *dev) +{ + bool mdio = true; + + /* If phy-handle property is passed from DT, use it as the PHY */ + plat->phy_node = of_parse_phandle(np, "phy-handle", 0); + if (plat->phy_node) + dev_dbg(dev, "Found phy-handle subnode\n"); + + /* If phy-handle is not specified, check if we have a fixed-phy */ + if (!plat->phy_node && of_phy_is_fixed_link(np)) { + if ((of_phy_register_fixed_link(np) < 0)) + return -ENODEV; + + dev_dbg(dev, "Found fixed-link subnode\n"); + plat->phy_node = of_node_get(np); + mdio = false; + } + + /* If snps,dwmac-mdio is passed from DT, always register the MDIO */ + for_each_child_of_node(np, plat->mdio_node) { + if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio")) + break; + } + + if (plat->mdio_node) { + dev_dbg(dev, "Found MDIO subnode\n"); + mdio = true; + } + + if (mdio) + plat->mdio_bus_data = + devm_kzalloc(dev, sizeof(struct stmmac_mdio_bus_data), + GFP_KERNEL); + return 0; +} + +/** * stmmac_probe_config_dt - parse device-tree driver parameters * @pdev: platform_device structure * @plat: driver data platform structure @@ -146,7 +209,6 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) struct device_node *np = pdev->dev.of_node; struct plat_stmmacenet_data *plat; struct stmmac_dma_cfg *dma_cfg; - struct device_node *child_node = NULL; plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL); if (!plat) @@ -166,36 +228,15 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) /* Default to phy auto-detection */ plat->phy_addr = -1; - /* If we find a phy-handle property, use it as the PHY */ - plat->phy_node = of_parse_phandle(np, "phy-handle", 0); - - /* If phy-handle is not specified, check if we have a fixed-phy */ - if (!plat->phy_node && of_phy_is_fixed_link(np)) { - if ((of_phy_register_fixed_link(np) < 0)) - return ERR_PTR(-ENODEV); - - plat->phy_node = of_node_get(np); - } - - for_each_child_of_node(np, child_node) - if (of_device_is_compatible(child_node, "snps,dwmac-mdio")) { - plat->mdio_node = child_node; - break; - } - /* "snps,phy-addr" is not a standard property. Mark it as deprecated * and warn of its use. Remove this when phy node support is added. */ if (of_property_read_u32(np, "snps,phy-addr", &plat->phy_addr) == 0) dev_warn(&pdev->dev, "snps,phy-addr property is deprecated\n"); - if ((plat->phy_node && !of_phy_is_fixed_link(np)) || !plat->mdio_node) - plat->mdio_bus_data = NULL; - else - plat->mdio_bus_data = - devm_kzalloc(&pdev->dev, - sizeof(struct stmmac_mdio_bus_data), - GFP_KERNEL); + /* To Configure PHY by using all device-tree supported properties */ + if (stmmac_dt_phy(plat, np, &pdev->dev)) + return ERR_PTR(-ENODEV); of_property_read_u32(np, "tx-fifo-depth", &plat->tx_fifo_size); |