diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/devicetree/bindings/pci/uniphier-pcie.txt | 81 |
1 files changed, 81 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt new file mode 100644 index 000000000000..1fa2c5906d4d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt @@ -0,0 +1,81 @@ +Socionext UniPhier PCIe host controller bindings + +This describes the devicetree bindings for PCIe host controller implemented +on Socionext UniPhier SoCs. + +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Required properties: +- compatible: Should be "socionext,uniphier-pcie". +- reg: Specifies offset and length of the register set for the device. + According to the reg-names, appropriate register sets are required. +- reg-names: Must include the following entries: + "dbi" - controller configuration registers + "link" - SoC-specific glue layer registers + "config" - PCIe configuration space +- clocks: A phandle to the clock gate for PCIe glue layer including + the host controller. +- resets: A phandle to the reset line for PCIe glue layer including + the host controller. +- interrupts: A list of interrupt specifiers. According to the + interrupt-names, appropriate interrupts are required. +- interrupt-names: Must include the following entries: + "dma" - DMA interrupt + "msi" - MSI interrupt + +Optional properties: +- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate + phys are required. +- phy-names: Must be "pcie-phy". + +Required sub-node: +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI + interrupts. + +Required properties for legacy-interrupt-controller: +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-parent: Phandle to the parent interrupt controller. +- interrupts: An interrupt specifier for legacy interrupt. + +Example: + + pcie: pcie@66000000 { + compatible = "socionext,uniphier-pcie", "snps,dw-pcie"; + status = "disabled"; + reg-names = "dbi", "link", "config"; + reg = <0x66000000 0x1000>, <0x66010000 0x10000>, + <0x2fff0000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + num-lanes = <1>; + num-viewport = <1>; + bus-range = <0x0 0xff>; + device_type = "pci"; + ranges = + /* downstream I/O */ + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>; + #interrupt-cells = <1>; + interrupt-names = "dma", "msi"; + interrupts = <0 224 4>, <0 225 4>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */ + <0 0 0 2 &pcie_intc 1>, /* INTB */ + <0 0 0 3 &pcie_intc 2>, /* INTC */ + <0 0 0 4 &pcie_intc 3>; /* INTD */ + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <0 226 4>; + }; + }; |