1 files changed, 0 insertions, 115 deletions
diff --git a/Documentation/networking/device_drivers/ethernet/neterion/vxge.rst b/Documentation/networking/device_drivers/ethernet/neterion/vxge.rst
deleted file mode 100644
index 589c6b15c63d..000000000000
--- a/Documentation/networking/device_drivers/ethernet/neterion/vxge.rst
+++ /dev/null
@@ -1,115 +0,0 @@
-.. SPDX-License-Identifier: GPL-2.0
-
-==============================================================================
-Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
-==============================================================================
-
-.. Contents
-
-  1) Introduction
-  2) Features supported
-  3) Configurable driver parameters
-  4) Troubleshooting
-
-1. Introduction
-===============
-
-This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
-Virtualized Server adapters.
-
-The X3100 series supports four modes of operation, configurable via
-firmware:
-
-	- Single function mode
-	- Multi function mode
-	- SRIOV mode
-	- MRIOV mode
-
-The functions share a 10GbE link and the pci-e bus, but hardly anything else
-inside the ASIC. Features like independent hw reset, statistics, bandwidth/
-priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
-supported independently on each function.
-
-(See below for a complete list of features supported for both IPv4 and IPv6)
-
-2. Features supported
-=====================
-
-i)   Single function mode (up to 17 queues)
-
-ii)  Multi function mode (up to 17 functions)
-
-iii) PCI-SIG's I/O Virtualization
-
-       - Single Root mode: v1.0 (up to 17 functions)
-       - Multi-Root mode: v1.0 (up to 17 functions)
-
-iv)  Jumbo frames
-
-       X3100 Series supports MTU up to 9600 bytes, modifiable using
-       ip command.
-
-v)   Offloads supported: (Enabled by default)
-
-       - Checksum offload (TCP/UDP/IP) on transmit and receive paths
-       - TCP Segmentation Offload (TSO) on transmit path
-       - Generic Receive Offload (GRO) on receive path
-
-vi)  MSI-X: (Enabled by default)
-
-       Resulting in noticeable performance improvement (up to 7% on certain
-       platforms).
-
-vii) NAPI: (Enabled by default)
-
-       For better Rx interrupt moderation.
-
-viii)RTH (Receive Traffic Hash): (Enabled by default)
-
-       Receive side steering for better scaling.
-
-ix)  Statistics
-
-       Comprehensive MAC-level and software statistics displayed using
-       "ethtool -S" option.
-
-x)   Multiple hardware queues: (Enabled by default)
-
-       Up to 17 hardware based transmit and receive data channels, with
-       multiple steering options (transmit multiqueue enabled by default).
-
-3) Configurable driver parameters:
-----------------------------------
-
-i)  max_config_dev
-       Specifies maximum device functions to be enabled.
-
-       Valid range: 1-8
-
-ii) max_config_port
-       Specifies number of ports to be enabled.
-
-       Valid range: 1,2
-
-       Default: 1
-
-iii) max_config_vpath
-       Specifies maximum VPATH(s) configured for each device function.
-
-       Valid range: 1-17
-
-iv) vlan_tag_strip
-       Enables/disables vlan tag stripping from all received tagged frames that
-       are not replicated at the internal L2 switch.
-
-       Valid range: 0,1 (disabled, enabled respectively)
-
-       Default: 1
-
-v)  addr_learn_en
-       Enable learning the mac address of the guest OS interface in
-       virtualization environment.
-
-       Valid range: 0,1 (disabled, enabled respectively)
-
-       Default: 0