diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
10 files changed, 213 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt new file mode 100644 index 000000000000..790311a42bf1 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt @@ -0,0 +1,39 @@ +GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP v3 core is a GENI based AHB slave that provides a common data path +(an output FIFO and an input FIFO) for serial peripheral interface (SPI) +mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Must contain "qcom,geni-spi". +- reg: Must contain SPI register location and length. +- interrupts: Must contain SPI controller interrupts. +- clock-names: Must contain "se". +- clocks: Serial engine core clock needed by the device. +- #address-cells: Must be <1> to define a chip select address on + the SPI bus. +- #size-cells: Must be <0>. + +SPI Controller nodes must be child of GENI based Qualcomm Universal +Peripharal. Please refer GENI based QUP wrapper controller node bindings +described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt. + +SPI slave nodes must be children of the SPI master node and conform to SPI bus +binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + spi0: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0xa84000 0x4000>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "se"; + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qup_1_spi_2_active>; + pinctrl-1 = <&qup_1_spi_2_sleep>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt new file mode 100644 index 000000000000..1d64b61f5171 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt @@ -0,0 +1,36 @@ +Qualcomm Quad Serial Peripheral Interface (QSPI) + +The QSPI controller allows SPI protocol communication in single, dual, or quad +wire transmission modes for read/write access to slaves such as NOR flash. + +Required properties: +- compatible: An SoC specific identifier followed by "qcom,qspi-v1", such as + "qcom,sdm845-qspi", "qcom,qspi-v1" +- reg: Should contain the base register location and length. +- interrupts: Interrupt number used by the controller. +- clocks: Should contain the core and AHB clock. +- clock-names: Should be "core" for core clock and "iface" for AHB clock. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + qspi: spi@88df000 { + compatible = "qcom,sdm845-qspi", "qcom,qspi-v1"; + reg = <0x88df000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "iface", "core"; + clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <&gcc GCC_QSPI_CORE_CLK>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index bfbc2035fb6b..4b836ad17b19 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -2,7 +2,9 @@ Renesas MSIOF spi controller Required properties: - compatible : "renesas,msiof-r8a7743" (RZ/G1M) + "renesas,msiof-r8a7744" (RZ/G1N) "renesas,msiof-r8a7745" (RZ/G1E) + "renesas,msiof-r8a774a1" (RZ/G2M) "renesas,msiof-r8a7790" (R-Car H2) "renesas,msiof-r8a7791" (R-Car M2-W) "renesas,msiof-r8a7792" (R-Car V2H) @@ -11,10 +13,14 @@ Required properties: "renesas,msiof-r8a7795" (R-Car H3) "renesas,msiof-r8a7796" (R-Car M3-W) "renesas,msiof-r8a77965" (R-Car M3-N) + "renesas,msiof-r8a77970" (R-Car V3M) + "renesas,msiof-r8a77980" (R-Car V3H) + "renesas,msiof-r8a77990" (R-Car E3) + "renesas,msiof-r8a77995" (R-Car D3) "renesas,msiof-sh73a0" (SH-Mobile AG5) "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device) "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device) - "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device) + "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device) "renesas,sh-msiof" (deprecated) When compatible with the generic version, nodes diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index 642d3fb1ef85..2864bc6b659c 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. Required properties: - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or - "jaguar2" + "jaguar2", or "amazon,alpine-dw-apb-ssi" - reg : The register base for the controller. For "mscc,<soc>-spi", a second register set is required (named ICPU_CFG:SPI_MST) - interrupts : One interrupt, used by the controller. diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt index 4af132606b37..8d178a4503cf 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt @@ -3,6 +3,7 @@ Required properties: - compatible : - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc - reg : address and length of the lpspi master registers - interrupts : lpspi interrupt - clocks : lpspi clock specifier diff --git a/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt new file mode 100644 index 000000000000..0335a9bd2e8a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pxa2xx.txt @@ -0,0 +1,24 @@ +PXA2xx SSP SPI Controller + +Required properties: +- compatible: Must be "marvell,mmp2-ssp". +- reg: Offset and length of the device's register set. +- interrupts: Should be the interrupt number. +- clocks: Should contain a single entry describing the clock input. +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + ssp1: spi@d4035000 { + compatible = "marvell,mmp2-ssp"; + reg = <0xd4035000 0x1000>; + clocks = <&soc_clocks MMP2_CLK_SSP0>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt index 96fd58548f69..fc97ad64fbf2 100644 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver Required properties: - compatible : For Renesas Serial Peripheral Interface on legacy SH: "renesas,rspi-<soctype>", "renesas,rspi" as fallback. - For Renesas Serial Peripheral Interface on RZ/A1H: + For Renesas Serial Peripheral Interface on RZ/A: "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. For Quad Serial Peripheral Interface on R-Car Gen2 and RZ/G1 devices: @@ -11,7 +11,9 @@ Required properties: Examples with soctypes are: - "renesas,rspi-sh7757" (SH) - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,rspi-r7s9210" (RZ/A2) - "renesas,qspi-r8a7743" (RZ/G1M) + - "renesas,qspi-r8a7744" (RZ/G1N) - "renesas,qspi-r8a7745" (RZ/G1E) - "renesas,qspi-r8a7790" (R-Car H2) - "renesas,qspi-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt new file mode 100644 index 000000000000..c37e5a179b21 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt @@ -0,0 +1,32 @@ +Binding for MTK SPI Slave controller + +Required properties: +- compatible: should be one of the following. + - mediatek,mt2712-spi-slave: for mt2712 platforms +- reg: Address and length of the register set for the device. +- interrupts: Should contain spi interrupt. +- clocks: phandles to input clocks. + It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>. +- clock-names: should be "spi" for the clock gate. + +Optional properties: +- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>. +- assigned-clock-parents: parent of mux clock. + It's PLL, and should be one of the following. + - <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ. + It's the default one. + - <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ. + - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. + - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + +Example: +- SoC Specific Portion: +spis1: spi@10013000 { + compatible = "mediatek,mt2712-spi-slave"; + reg = <0 0x10013000 0 0x100>; + interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_AO_SPI1>; + clock-names = "spi"; + assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt new file mode 100644 index 000000000000..bad211a19da4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt @@ -0,0 +1,26 @@ +Spreadtrum SPI Controller + +Required properties: +- compatible: Should be "sprd,sc9860-spi". +- reg: Offset and length of SPI controller register space. +- interrupts: Should contain SPI interrupt. +- clock-names: Should contain following entries: + "spi" for SPI clock, + "source" for SPI source (parent) clock, + "enable" for SPI module enable clock. +- clocks: List of clock input name strings sorted in the same order + as the clock-names property. +- #address-cells: The number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be set to 0. + +Example: +spi0: spi@70a00000{ + compatible = "sprd,sc9860-spi"; + reg = <0 0x70a00000 0 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "spi", "source","enable"; + clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt new file mode 100644 index 000000000000..adeeb63e84b9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -0,0 +1,44 @@ +* STMicroelectronics Quad Serial Peripheral Interface(QSPI) + +Required properties: +- compatible: should be "st,stm32f469-qspi" +- reg: the first contains the register location and length. + the second contains the memory mapping address and length +- reg-names: should contain the reg names "qspi" "qspi_mm" +- interrupts: should contain the interrupt for the device +- clocks: the phandle of the clock needed by the QSPI controller +- A pinctrl must be defined to set pins in mode of operation for QSPI transfer + +Optional properties: +- resets: must contain the phandle to the reset controller. + +A spi flash (NOR/NAND) must be a child of spi node and could have some +properties. Also see jedec,spi-nor.txt. + +Required properties: +- reg: chip-Select number (QSPI controller may connect 2 flashes) +- spi-max-frequency: max frequency of spi bus + +Optional property: +- spi-rx-bus-width: see ./spi-bus.txt for the description + +Example: + +qspi: spi@a0001000 { + compatible = "st,stm32f469-qspi"; + reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <91>; + resets = <&rcc STM32F4_AHB3_RESET(QSPI)>; + clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi0>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + ... + }; +}; |