blob: 313a60ba61d8e61667bad2f627d738433f7854c8 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
TPS65090 regulators
Required properties:
- compatible: "ti,tps65090"
- reg: I2C slave address
- interrupts: the interrupt outputs of the controller
- regulators: A node that houses a sub-node for each regulator within the
device. Each sub-node is identified using the node's name, with valid
values listed below. The content of each sub-node is defined by the
standard binding for regulators; see regulator.txt.
dcdc[1-3], fet[1-7] and ldo[1-2] respectively.
- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively.
- infet[1-7]-supply: The input supply for FET[1-7] respectively.
- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively.
Optional properties:
- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
If DCDCs are externally controlled then this property should be there.
- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
If DCDCs are externally controlled and if it is from GPIO then GPIO
number should be provided. If it is externally controlled and no GPIO
entry then driver will just configure this rails as external control
and will not provide any enable/disable APIs.
Each regulator is defined using the standard binding for regulators.
Example:
tps65090@48 {
compatible = "ti,tps65090";
reg = <0x48>;
interrupts = <0 88 0x4>;
vsys1-supply = <&some_reg>;
vsys2-supply = <&some_reg>;
vsys3-supply = <&some_reg>;
infet1-supply = <&some_reg>;
infet2-supply = <&some_reg>;
infet3-supply = <&some_reg>;
infet4-supply = <&some_reg>;
infet5-supply = <&some_reg>;
infet6-supply = <&some_reg>;
infet7-supply = <&some_reg>;
vsys_l1-supply = <&some_reg>;
vsys_l2-supply = <&some_reg>;
regulators {
dcdc1 {
regulator-name = "dcdc1";
regulator-boot-on;
regulator-always-on;
ti,enable-ext-control;
dcdc-ext-control-gpios = <&gpio 10 0>;
};
dcdc2 {
regulator-name = "dcdc2";
regulator-boot-on;
regulator-always-on;
};
dcdc3 {
regulator-name = "dcdc3";
regulator-boot-on;
regulator-always-on;
};
fet1 {
regulator-name = "fet1";
regulator-boot-on;
regulator-always-on;
};
fet2 {
regulator-name = "fet2";
regulator-boot-on;
regulator-always-on;
};
fet3 {
regulator-name = "fet3";
regulator-boot-on;
regulator-always-on;
};
fet4 {
regulator-name = "fet4";
regulator-boot-on;
regulator-always-on;
};
fet5 {
regulator-name = "fet5";
regulator-boot-on;
regulator-always-on;
};
fet6 {
regulator-name = "fet6";
regulator-boot-on;
regulator-always-on;
};
fet7 {
regulator-name = "fet7";
regulator-boot-on;
regulator-always-on;
};
ldo1 {
regulator-name = "ldo1";
regulator-boot-on;
regulator-always-on;
};
ldo2 {
regulator-name = "ldo2";
regulator-boot-on;
regulator-always-on;
};
};
};
|
