1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
* Allwinner A1X Pin Controller
The pins controlled by sunXi pin controller are organized in banks,
each bank has 32 pins. Each pin has 7 multiplexing functions, with
the first two functions being GPIO in and out. The configuration on
the pins includes drive strength and pull-up.
Required properties:
- compatible: Should be one of the following (depending on your SoC):
"allwinner,sun4i-a10-pinctrl"
"allwinner,sun5i-a10s-pinctrl"
"allwinner,sun5i-a13-pinctrl"
"allwinner,sun6i-a31-pinctrl"
"allwinner,sun6i-a31s-pinctrl"
"allwinner,sun6i-a31-r-pinctrl"
"allwinner,sun7i-a20-pinctrl"
"allwinner,sun8i-a23-pinctrl"
"allwinner,sun8i-a23-r-pinctrl"
"allwinner,sun8i-a33-pinctrl"
"allwinner,sun9i-a80-pinctrl"
"allwinner,sun9i-a80-r-pinctrl"
"allwinner,sun8i-a83t-pinctrl"
"allwinner,sun8i-a83t-r-pinctrl"
"allwinner,sun8i-h3-pinctrl"
"allwinner,sun8i-h3-r-pinctrl"
"allwinner,sun8i-r40-pinctrl"
"allwinner,sun50i-a64-pinctrl"
"allwinner,sun50i-a64-r-pinctrl"
"allwinner,sun50i-h5-pinctrl"
"allwinner,sun50i-h6-pinctrl"
"allwinner,sun50i-h6-r-pinctrl"
"allwinner,suniv-f1c100s-pinctrl"
"nextthing,gr8-pinctrl"
- reg: Should contain the register physical address and length for the
pin controller.
- clocks: phandle to the clocks feeding the pin controller:
- "apb": the gated APB parent clock
- "hosc": the high frequency oscillator in the system
- "losc": the low frequency oscillator in the system
Note: For backward compatibility reasons, the hosc and losc clocks are only
required if you need to use the optional input-debounce property. Any new
device tree should set them.
Each pin bank, depending on the SoC, can have an associated regulator:
- vcc-pa-supply: for the A10, A20, A31, A31s, A80 and R40 SoCs
- vcc-pb-supply: for the A31, A31s, A80 and V3s SoCs
- vcc-pc-supply: for the A10, A20, A31, A31s, A64, A80, H5, R40 and V3s SoCs
- vcc-pd-supply: for the A23, A31, A31s, A64, A80, A83t, H3, H5 and R40 SoCs
- vcc-pe-supply: for the A10, A20, A31, A31s, A64, A80, R40 and V3s SoCs
- vcc-pf-supply: for the A10, A20, A31, A31s, A80, R40 and V3s SoCs
- vcc-pg-supply: for the A10, A20, A31, A31s, A64, A80, H3, H5, R40 and V3s SoCs
- vcc-ph-supply: for the A31, A31s and A80 SoCs
- vcc-pl-supply: for the r-pinctrl of the A64, A80 and A83t SoCs
- vcc-pm-supply: for the r-pinctrl of the A31, A31s and A80 SoCs
Optional properties:
- input-debounce: Array of debouncing periods in microseconds. One period per
irq bank found in the controller. 0 if no setup required.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices.
A pinctrl node should contain at least one subnodes representing the
pinctrl groups available on the machine. Each subnode will list the
pins it needs, and how they should be configured, with regard to muxer
configuration, drive strength and pullups. If one of these options is
not set, its actual value will be unspecified.
Allwinner A1X Pin Controller supports the generic pin multiplexing and
configuration bindings. For details on each properties, you can refer to
./pinctrl-bindings.txt.
Required sub-node properties:
- pins
- function
Optional sub-node properties:
- bias-disable
- bias-pull-up
- bias-pull-down
- drive-strength
*** Deprecated pin configuration and multiplexing binding
Required subnode-properties:
- allwinner,pins: List of strings containing the pin name.
- allwinner,function: Function to mux the pins listed above to.
Optional subnode-properties:
- allwinner,drive: Integer. Represents the current sent to the pin
0: 10 mA
1: 20 mA
2: 30 mA
3: 40 mA
- allwinner,pull: Integer.
0: No resistor
1: Pull-up resistor
2: Pull-down resistor
Examples:
pio: pinctrl@1c20800 {
compatible = "allwinner,sun5i-a13-pinctrl";
reg = <0x01c20800 0x400>;
#address-cells = <1>;
#size-cells = <0>;
uart1_pins_a: uart1@0 {
allwinner,pins = "PE10", "PE11";
allwinner,function = "uart1";
allwinner,drive = <0>;
allwinner,pull = <0>;
};
uart1_pins_b: uart1@1 {
allwinner,pins = "PG3", "PG4";
allwinner,function = "uart1";
allwinner,drive = <0>;
allwinner,pull = <0>;
};
};
GPIO and interrupt controller
-----------------------------
This hardware also acts as a GPIO controller and an interrupt
controller.
Consumers that would want to refer to one or the other (or both)
should provide through the usual *-gpios and interrupts properties a
cell with 3 arguments, first the number of the bank, then the pin
inside that bank, and finally the flags for the GPIO/interrupts.
Example:
xio: gpio@38 {
compatible = "nxp,pcf8574a";
reg = <0x38>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&pio>;
interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
};
reg_usb1_vbus: usb1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>;
};
|
