From a7aea373b4ca428f1be2c1fedd2f26c8e3f2864d Mon Sep 17 00:00:00 2001 From: "Ira W. Snyder" Date: Thu, 23 Apr 2009 16:17:54 -0700 Subject: fsldma: use PCI Read Multiple command By default, the Freescale 83xx DMA controller uses the PCI Read Line command when reading data over the PCI bus. Setting the controller to use the PCI Read Multiple command instead allows the controller to read much larger bursts of data, which provides a drastic speed increase. The slowdown due to using PCI Read Line was only observed when a PCI-to-PCI bridge was between the devices trying to communicate. A simple test driver showed an increase from 4MB/sec to 116MB/sec when performing DMA over the PCI bus. Using DMA to transfer between blocks of local SDRAM showed no change in performance with this patch. The dmatest driver was also used to verify the correctness of the transfers, and showed no errors. Signed-off-by: Ira W. Snyder Acked-by: Timur Tabi Acked-by: Kumar Gala Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 10 ++++++++-- drivers/dma/fsldma.h | 1 + 2 files changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index f18d1bde0439..a1cb25e277b5 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -12,6 +12,11 @@ * also fit for MPC8560, MPC8555, MPC8548, MPC8641, and etc. * The support for MPC8349 DMA contorller is also added. * + * This driver instructs the DMA controller to issue the PCI Read Multiple + * command for PCI read operations, instead of using the default PCI Read Line + * command. Please be aware that this setting may result in read pre-fetching + * on some platforms. + * * This is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -49,9 +54,10 @@ static void dma_init(struct fsl_dma_chan *fsl_chan) case FSL_DMA_IP_83XX: /* Set the channel to below modes: * EOTIE - End-of-transfer interrupt enable + * PRC_RM - PCI read multiple */ - DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE, - 32); + DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE + | FSL_DMA_MR_PRC_RM, 32); break; } diff --git a/drivers/dma/fsldma.h b/drivers/dma/fsldma.h index 4f21a512d848..dc7f26865797 100644 --- a/drivers/dma/fsldma.h +++ b/drivers/dma/fsldma.h @@ -38,6 +38,7 @@ /* Special MR definition for MPC8349 */ #define FSL_DMA_MR_EOTIE 0x00000080 +#define FSL_DMA_MR_PRC_RM 0x00000800 #define FSL_DMA_SR_CH 0x00000020 #define FSL_DMA_SR_PE 0x00000010 -- cgit v1.2.3 From be30b226f2ae618cd719e40267d9923db1db9001 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:20:42 +0000 Subject: fsldma: enable external start for the 83xx controller The 83xx controller has external start capability, but lacks external pause capability. Hook up the external start function pointer for the 83xx controller. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index a1cb25e277b5..10bcf0cb0efc 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -877,9 +877,9 @@ static int __devinit fsl_dma_chan_probe(struct fsl_dma_device *fdev, switch (new_fsl_chan->feature & FSL_DMA_IP_MASK) { case FSL_DMA_IP_85XX: - new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->toggle_ext_pause = fsl_chan_toggle_ext_pause; case FSL_DMA_IP_83XX: + new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start; new_fsl_chan->set_src_loop_size = fsl_chan_set_src_loop_size; new_fsl_chan->set_dest_loop_size = fsl_chan_set_dest_loop_size; } -- cgit v1.2.3 From 43a1a3ed6bf5a1b9ae197b4f5f20033baf19db61 Mon Sep 17 00:00:00 2001 From: Ira Snyder Date: Thu, 28 May 2009 09:26:40 +0000 Subject: fsldma: do not clear bandwidth control bits on the 83xx controller The 83xx controller does not support the external pause feature. The bit in the mode register that controls external pause on the 85xx controller happens to be part of the bandwidth control settings for the 83xx controller. This patch fixes the driver so that it only clears the external pause bit if the hardware is the 85xx controller. When driving the 83xx controller, the bit is left untouched. This follows the existing convention that mode registers settings are not touched unless necessary. Signed-off-by: Ira W. Snyder Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 10bcf0cb0efc..6e60c77a145c 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -147,10 +147,11 @@ static void dma_start(struct fsl_dma_chan *fsl_chan) if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); mr_set |= FSL_DMA_MR_EMP_EN; - } else + } else if ((fsl_chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) & ~FSL_DMA_MR_EMP_EN, 32); + } if (fsl_chan->feature & FSL_DMA_CHAN_START_EXT) mr_set |= FSL_DMA_MR_EMS_EN; -- cgit v1.2.3 From 4859484b0957ddc7fe3e0fa349d98b0f1c7876bd Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Fri, 19 Jun 2009 23:24:11 +0200 Subject: HID: hiddev, fix lock imbalance Add omitted BKL to one switch/case. Cc: Stable Signed-off-by: Jiri Slaby Signed-off-by: Jiri Kosina --- drivers/hid/usbhid/hiddev.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/hid/usbhid/hiddev.c b/drivers/hid/usbhid/hiddev.c index e9b436d2d944..39e27f4be4ac 100644 --- a/drivers/hid/usbhid/hiddev.c +++ b/drivers/hid/usbhid/hiddev.c @@ -527,8 +527,10 @@ static noinline int hiddev_ioctl_usage(struct hiddev *hiddev, unsigned int cmd, goto goodreturn; case HIDIOCGCOLLECTIONINDEX: + i = field->usage[uref->usage_index].collection_index; + unlock_kernel(); kfree(uref_multi); - return field->usage[uref->usage_index].collection_index; + return i; case HIDIOCGUSAGES: for (i = 0; i < uref_multi->num_values; i++) uref_multi->values[i] = -- cgit v1.2.3 From 04a820ead0838c76e9c1242feb5e71048bf3e9dc Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Tue, 30 Jun 2009 02:14:00 -0400 Subject: olpc_battery: Fix up eeprom read function The eeprom read function was placing values into the wrong place in 'buf'; we were starting from buf[off], rather than buf[0]. Also, the for loop that we were using was much uglier than it needed to be. This cleans it up a bit. Signed-off-by: Andres Salomon Signed-off-by: Anton Vorontsov --- drivers/power/olpc_battery.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c index 5fbca2681baa..9c216dd41550 100644 --- a/drivers/power/olpc_battery.c +++ b/drivers/power/olpc_battery.c @@ -8,6 +8,7 @@ * published by the Free Software Foundation. */ +#include #include #include #include @@ -334,21 +335,21 @@ static ssize_t olpc_bat_eeprom_read(struct kobject *kobj, struct bin_attribute *attr, char *buf, loff_t off, size_t count) { uint8_t ec_byte; - int ret, end; + int ret; + int i; if (off >= EEPROM_SIZE) return 0; if (off + count > EEPROM_SIZE) count = EEPROM_SIZE - off; - end = EEPROM_START + off + count; - for (ec_byte = EEPROM_START + off; ec_byte < end; ec_byte++) { - ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, - &buf[ec_byte - EEPROM_START], 1); + for (i = 0; i < count; i++) { + ec_byte = EEPROM_START + off + i; + ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &buf[i], 1); if (ret) { - printk(KERN_ERR "olpc-battery: EC command " - "EC_BAT_EEPROM @ 0x%x failed -" - " %d!\n", ec_byte, ret); + pr_err("olpc-battery: " + "EC_BAT_EEPROM cmd @ 0x%x failed - %d!\n", + ec_byte, ret); return -EIO; } } -- cgit v1.2.3 From 8f7e57985fa794ab6afdcd3642581d9e1fe6de31 Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Tue, 30 Jun 2009 02:16:17 -0400 Subject: olpc_battery: Ensure that the TRICKLE bit is checked There are times when the battery is present but trickle charging, and the EC sets only the TRICKLE bit. So we must check for the bit when we're checking the charging/present status. Signed-off-by: Andres Salomon Signed-off-by: Anton Vorontsov --- drivers/power/olpc_battery.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c index 9c216dd41550..58e419299cd6 100644 --- a/drivers/power/olpc_battery.c +++ b/drivers/power/olpc_battery.c @@ -36,6 +36,7 @@ #define BAT_STAT_AC 0x10 #define BAT_STAT_CHARGING 0x20 #define BAT_STAT_DISCHARGING 0x40 +#define BAT_STAT_TRICKLE 0x80 #define BAT_ERR_INFOFAIL 0x02 #define BAT_ERR_OVERVOLTAGE 0x04 @@ -90,7 +91,7 @@ static char bat_serial[17]; /* Ick */ static int olpc_bat_get_status(union power_supply_propval *val, uint8_t ec_byte) { if (olpc_platform_info.ecver > 0x44) { - if (ec_byte & BAT_STAT_CHARGING) + if (ec_byte & (BAT_STAT_CHARGING | BAT_STAT_TRICKLE)) val->intval = POWER_SUPPLY_STATUS_CHARGING; else if (ec_byte & BAT_STAT_DISCHARGING) val->intval = POWER_SUPPLY_STATUS_DISCHARGING; @@ -220,7 +221,8 @@ static int olpc_bat_get_property(struct power_supply *psy, It doesn't matter though -- the EC will return the last-known information, and it's as if we just ran that _little_ bit faster and managed to read it out before the battery went away. */ - if (!(ec_byte & BAT_STAT_PRESENT) && psp != POWER_SUPPLY_PROP_PRESENT) + if (!(ec_byte & (BAT_STAT_PRESENT | BAT_STAT_TRICKLE)) && + psp != POWER_SUPPLY_PROP_PRESENT) return -ENODEV; switch (psp) { @@ -230,7 +232,8 @@ static int olpc_bat_get_property(struct power_supply *psy, return ret; break; case POWER_SUPPLY_PROP_PRESENT: - val->intval = !!(ec_byte & BAT_STAT_PRESENT); + val->intval = !!(ec_byte & (BAT_STAT_PRESENT | + BAT_STAT_TRICKLE)); break; case POWER_SUPPLY_PROP_HEALTH: -- cgit v1.2.3 From bfdb46ce8494eae30dbaae65c81e684e6db6228b Mon Sep 17 00:00:00 2001 From: Ryan Mallon Date: Thu, 18 Jun 2009 11:26:26 +1200 Subject: Add ds2782 battery gas gauge driver This patch adds a driver for ds2782 battery devices. Signed-off-by: Ryan Mallon Signed-off-by: Anton Vorontsov --- drivers/power/Kconfig | 7 + drivers/power/Makefile | 1 + drivers/power/ds2782_battery.c | 330 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 338 insertions(+) create mode 100644 drivers/power/ds2782_battery.c (limited to 'drivers') diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 7eda34838bfe..bdbc4f73fcdc 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -43,6 +43,13 @@ config BATTERY_DS2760 help Say Y here to enable support for batteries with ds2760 chip. +config BATTERY_DS2782 + tristate "DS2782 standalone gas-gauge" + depends on I2C + help + Say Y here to enable support for the DS2782 standalone battery + gas-gauge. + config BATTERY_PMU tristate "Apple PMU battery" depends on PPC32 && ADB_PMU diff --git a/drivers/power/Makefile b/drivers/power/Makefile index daf3179689aa..380d17c9ae29 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -19,6 +19,7 @@ obj-$(CONFIG_APM_POWER) += apm_power.o obj-$(CONFIG_WM8350_POWER) += wm8350_power.o obj-$(CONFIG_BATTERY_DS2760) += ds2760_battery.o +obj-$(CONFIG_BATTERY_DS2782) += ds2782_battery.o obj-$(CONFIG_BATTERY_PMU) += pmu_battery.o obj-$(CONFIG_BATTERY_OLPC) += olpc_battery.o obj-$(CONFIG_BATTERY_TOSA) += tosa_battery.o diff --git a/drivers/power/ds2782_battery.c b/drivers/power/ds2782_battery.c new file mode 100644 index 000000000000..da14f374cb60 --- /dev/null +++ b/drivers/power/ds2782_battery.c @@ -0,0 +1,330 @@ +/* + * I2C client/driver for the Maxim/Dallas DS2782 Stand-Alone Fuel Gauge IC + * + * Copyright (C) 2009 Bluewater Systems Ltd + * + * Author: Ryan Mallon + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define DS2782_REG_RARC 0x06 /* Remaining active relative capacity */ + +#define DS2782_REG_VOLT_MSB 0x0c +#define DS2782_REG_TEMP_MSB 0x0a +#define DS2782_REG_CURRENT_MSB 0x0e + +/* EEPROM Block */ +#define DS2782_REG_RSNSP 0x69 /* Sense resistor value */ + +/* Current unit measurement in uA for a 1 milli-ohm sense resistor */ +#define DS2782_CURRENT_UNITS 1563 + +#define to_ds2782_info(x) container_of(x, struct ds2782_info, battery) + +struct ds2782_info { + struct i2c_client *client; + struct power_supply battery; + int id; +}; + +static DEFINE_IDR(battery_id); +static DEFINE_MUTEX(battery_lock); + +static inline int ds2782_read_reg(struct ds2782_info *info, int reg, u8 *val) +{ + int ret; + + ret = i2c_smbus_read_byte_data(info->client, reg); + if (ret < 0) { + dev_err(&info->client->dev, "register read failed\n"); + return ret; + } + + *val = ret; + return 0; +} + +static inline int ds2782_read_reg16(struct ds2782_info *info, int reg_msb, + s16 *val) +{ + int ret; + + ret = swab16(i2c_smbus_read_word_data(info->client, reg_msb)); + if (ret < 0) { + dev_err(&info->client->dev, "register read failed\n"); + return ret; + } + + *val = ret; + return 0; +} + +static int ds2782_get_temp(struct ds2782_info *info, int *temp) +{ + s16 raw; + int err; + + /* + * Temperature is measured in units of 0.125 degrees celcius, the + * power_supply class measures temperature in tenths of degrees + * celsius. The temperature value is stored as a 10 bit number, plus + * sign in the upper bits of a 16 bit register. + */ + err = ds2782_read_reg16(info, DS2782_REG_TEMP_MSB, &raw); + if (err) + return err; + *temp = ((raw / 32) * 125) / 100; + return 0; +} + +static int ds2782_get_current(struct ds2782_info *info, int *current_uA) +{ + int sense_res; + int err; + u8 sense_res_raw; + s16 raw; + + /* + * The units of measurement for current are dependent on the value of + * the sense resistor. + */ + err = ds2782_read_reg(info, DS2782_REG_RSNSP, &sense_res_raw); + if (err) + return err; + if (sense_res_raw == 0) { + dev_err(&info->client->dev, "sense resistor value is 0\n"); + return -ENXIO; + } + sense_res = 1000 / sense_res_raw; + + dev_dbg(&info->client->dev, "sense resistor = %d milli-ohms\n", + sense_res); + err = ds2782_read_reg16(info, DS2782_REG_CURRENT_MSB, &raw); + if (err) + return err; + *current_uA = raw * (DS2782_CURRENT_UNITS / sense_res); + return 0; +} + +static int ds2782_get_voltage(struct ds2782_info *info, int *voltage_uA) +{ + s16 raw; + int err; + + /* + * Voltage is measured in units of 4.88mV. The voltage is stored as + * a 10-bit number plus sign, in the upper bits of a 16-bit register + */ + err = ds2782_read_reg16(info, DS2782_REG_VOLT_MSB, &raw); + if (err) + return err; + *voltage_uA = (raw / 32) * 4800; + return 0; +} + +static int ds2782_get_capacity(struct ds2782_info *info, int *capacity) +{ + int err; + u8 raw; + + err = ds2782_read_reg(info, DS2782_REG_RARC, &raw); + if (err) + return err; + *capacity = raw; + return raw; +} + +static int ds2782_get_status(struct ds2782_info *info, int *status) +{ + int err; + int current_uA; + int capacity; + + err = ds2782_get_current(info, ¤t_uA); + if (err) + return err; + + err = ds2782_get_capacity(info, &capacity); + if (err) + return err; + + if (capacity == 100) + *status = POWER_SUPPLY_STATUS_FULL; + else if (current_uA == 0) + *status = POWER_SUPPLY_STATUS_NOT_CHARGING; + else if (current_uA < 0) + *status = POWER_SUPPLY_STATUS_DISCHARGING; + else + *status = POWER_SUPPLY_STATUS_CHARGING; + + return 0; +} + +static int ds2782_battery_get_property(struct power_supply *psy, + enum power_supply_property prop, + union power_supply_propval *val) +{ + struct ds2782_info *info = to_ds2782_info(psy); + int ret; + + switch (prop) { + case POWER_SUPPLY_PROP_STATUS: + ret = ds2782_get_status(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_CAPACITY: + ret = ds2782_get_capacity(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + ret = ds2782_get_voltage(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_CURRENT_NOW: + ret = ds2782_get_current(info, &val->intval); + break; + + case POWER_SUPPLY_PROP_TEMP: + ret = ds2782_get_temp(info, &val->intval); + break; + + default: + ret = -EINVAL; + } + + return ret; +} + +static enum power_supply_property ds2782_battery_props[] = { + POWER_SUPPLY_PROP_STATUS, + POWER_SUPPLY_PROP_CAPACITY, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_TEMP, +}; + +static void ds2782_power_supply_init(struct power_supply *battery) +{ + battery->type = POWER_SUPPLY_TYPE_BATTERY; + battery->properties = ds2782_battery_props; + battery->num_properties = ARRAY_SIZE(ds2782_battery_props); + battery->get_property = ds2782_battery_get_property; + battery->external_power_changed = NULL; +} + +static int ds2782_battery_remove(struct i2c_client *client) +{ + struct ds2782_info *info = i2c_get_clientdata(client); + + power_supply_unregister(&info->battery); + kfree(info->battery.name); + + mutex_lock(&battery_lock); + idr_remove(&battery_id, info->id); + mutex_unlock(&battery_lock); + + i2c_set_clientdata(client, info); + + kfree(info); + return 0; +} + +static int ds2782_battery_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct ds2782_info *info; + int ret; + int num; + + /* Get an ID for this battery */ + ret = idr_pre_get(&battery_id, GFP_KERNEL); + if (ret == 0) { + ret = -ENOMEM; + goto fail_id; + } + + mutex_lock(&battery_lock); + ret = idr_get_new(&battery_id, client, &num); + mutex_unlock(&battery_lock); + if (ret < 0) + goto fail_id; + + info = kzalloc(sizeof(*info), GFP_KERNEL); + if (!info) { + ret = -ENOMEM; + goto fail_info; + } + + info->battery.name = kasprintf(GFP_KERNEL, "ds2782-%d", num); + if (!info->battery.name) { + ret = -ENOMEM; + goto fail_name; + } + + i2c_set_clientdata(client, info); + info->client = client; + ds2782_power_supply_init(&info->battery); + + ret = power_supply_register(&client->dev, &info->battery); + if (ret) { + dev_err(&client->dev, "failed to register battery\n"); + goto fail_register; + } + + return 0; + +fail_register: + kfree(info->battery.name); +fail_name: + i2c_set_clientdata(client, info); + kfree(info); +fail_info: + mutex_lock(&battery_lock); + idr_remove(&battery_id, num); + mutex_unlock(&battery_lock); +fail_id: + return ret; +} + +static const struct i2c_device_id ds2782_id[] = { + {"ds2782", 0}, + {}, +}; + +static struct i2c_driver ds2782_battery_driver = { + .driver = { + .name = "ds2782-battery", + }, + .probe = ds2782_battery_probe, + .remove = ds2782_battery_remove, + .id_table = ds2782_id, +}; + +static int __init ds2782_init(void) +{ + return i2c_add_driver(&ds2782_battery_driver); +} +module_init(ds2782_init); + +static void __exit ds2782_exit(void) +{ + i2c_del_driver(&ds2782_battery_driver); +} +module_exit(ds2782_exit); + +MODULE_AUTHOR("Ryan Mallon "); +MODULE_DESCRIPTION("Maxim/Dallas DS2782 Stand-Alone Fuel Gauage IC driver"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From daf4219dbcbb2efcd638fcd3c29a622e1c18cc38 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 1 Jul 2009 16:12:53 -0700 Subject: dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA On HIGHMEM64G systems dma_addr_t is known to be larger than (void *) which precludes async_xor from performing dma address conversions by reusing the input parameter address list. However, other parts of the dmaengine infrastructure do not suffer this constraint, so the HIGHMEM64G restriction can be down-levelled. Signed-off-by: Dan Williams --- crypto/async_tx/async_xor.c | 2 +- drivers/dma/Kconfig | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/crypto/async_tx/async_xor.c b/crypto/async_tx/async_xor.c index 95fe2c8d6c51..90dd3f8bd283 100644 --- a/crypto/async_tx/async_xor.c +++ b/crypto/async_tx/async_xor.c @@ -300,7 +300,7 @@ EXPORT_SYMBOL_GPL(async_xor_zero_sum); static int __init async_xor_init(void) { - #ifdef CONFIG_DMA_ENGINE + #ifdef CONFIG_ASYNC_TX_DMA /* To conserve stack space the input src_list (array of page pointers) * is reused to hold the array of dma addresses passed to the driver. * This conversion is only possible when dma_addr_t is less than the diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index 3b3c01b6f1ee..babf214a509b 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -4,7 +4,7 @@ menuconfig DMADEVICES bool "DMA Engine support" - depends on !HIGHMEM64G && HAS_DMA + depends on HAS_DMA help DMA engines can do asynchronous data transfers without involving the host CPU. Currently, this framework can be @@ -100,7 +100,7 @@ config NET_DMA config ASYNC_TX_DMA bool "Async_tx: Offload support for the async_tx api" - depends on DMA_ENGINE + depends on DMA_ENGINE && !HIGHMEM64G help This allows the async_tx api to take advantage of offload engines for memcpy, memset, xor, and raid6 p+q operations. If your platform has -- cgit v1.2.3 From 7eeff4814224646c896303ba2c2b7ac3c4240cd2 Mon Sep 17 00:00:00 2001 From: Matt Reimer Date: Mon, 15 Jun 2009 13:21:25 -0700 Subject: pxamci: correct DMA flow control The DMA flow control in pxamci_setup_data() is backwards; fix it. Signed-off-by: Matt Reimer Acked-by: Robert Jarzmik Signed-off-by: Eric Miao --- drivers/mmc/host/pxamci.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index d7d7109ef47e..e55ac792d68c 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -168,12 +168,12 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data) if (data->flags & MMC_DATA_READ) { host->dma_dir = DMA_FROM_DEVICE; - dcmd = DCMD_INCTRGADDR | DCMD_FLOWTRG; + dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC; DRCMR(host->dma_drcmrtx) = 0; DRCMR(host->dma_drcmrrx) = host->dma | DRCMR_MAPVLD; } else { host->dma_dir = DMA_TO_DEVICE; - dcmd = DCMD_INCSRCADDR | DCMD_FLOWSRC; + dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG; DRCMR(host->dma_drcmrrx) = 0; DRCMR(host->dma_drcmrtx) = host->dma | DRCMR_MAPVLD; } -- cgit v1.2.3 From 82e8b54229fb121946151b82e8ff3c3284bd723f Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Fri, 19 Jun 2009 10:50:54 +0200 Subject: backlight: fix pwm_bl.c to notify platform code when suspending When suspending, pwm-bl sets duty cycle to 0, and shuts down the pwm device. This patch ensure that the platform code is called before that (through the notify callback_, leaving a chance for the platform code to configure GPIOs (shutting off the backlight, for example), much like it is done during normal operations. Signed-off-by: Marc Zyngier Signed-off-by: Eric Miao --- drivers/video/backlight/pwm_bl.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c index e641584e212e..887166267443 100644 --- a/drivers/video/backlight/pwm_bl.c +++ b/drivers/video/backlight/pwm_bl.c @@ -145,6 +145,8 @@ static int pwm_backlight_suspend(struct platform_device *pdev, struct backlight_device *bl = platform_get_drvdata(pdev); struct pwm_bl_data *pb = dev_get_drvdata(&bl->dev); + if (pb->notify) + pb->notify(0); pwm_config(pb->pwm, 0, pb->period); pwm_disable(pb->pwm); return 0; -- cgit v1.2.3 From e705cee427e319665969ef7ac664f3612dec8899 Mon Sep 17 00:00:00 2001 From: Giuseppe Mazzotta Date: Sun, 12 Jul 2009 21:02:27 -0700 Subject: Input: wistron_btns - recognize Maxdata Pro 7000 notebooks This patch adds DMI information to automatically load the correct layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks are clones of Fujitsu Amilo V2000, the hook for the v2000 is being used and I have tested that perfectly works. The immediate result of integrating this patch is that the five special buttons will work on these specific notebook models and that the RF killswitch will not be activated after suspend. This patch definitively obsoletes the fsam7400 module which I was still needing to enable wifi and to fix the RF killswitch suspend problem; in the current 2.6.30 kernel it is necessary to load the wistron_btns module with options 'force=1 keymap=1557/MS2141', which was not anyway a complete workaround. Signed-off-by: Giuseppe Mazzotta Signed-off-by: Dmitry Torokhov --- drivers/input/misc/wistron_btns.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'drivers') diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c index 7c8957dd22c0..26e17a9a22eb 100644 --- a/drivers/input/misc/wistron_btns.c +++ b/drivers/input/misc/wistron_btns.c @@ -644,6 +644,15 @@ static struct dmi_system_id dmi_ids[] __initdata = { }, .driver_data = keymap_fs_amilo_pro_v2000 }, + { + .callback = dmi_matched, + .ident = "Maxdata Pro 7000 DX", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "MAXDATA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Pro 7000"), + }, + .driver_data = keymap_fs_amilo_pro_v2000 + }, { .callback = dmi_matched, .ident = "Fujitsu N3510", -- cgit v1.2.3 From 70a6f2e6d6b8653d394b63210ec57b4c78f3dcd8 Mon Sep 17 00:00:00 2001 From: Michael Gruber Date: Sun, 12 Jul 2009 20:51:36 -0700 Subject: Input: xpad - don't resend successfully sent outgoing requests This avoids an infinite loop. Signed-off-by: Michael Gruber Signed-off-by: Dmitry Torokhov --- drivers/input/joystick/xpad.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c index b868b8d5fbb3..f155ad8cdae7 100644 --- a/drivers/input/joystick/xpad.c +++ b/drivers/input/joystick/xpad.c @@ -470,20 +470,20 @@ static void xpad_irq_out(struct urb *urb) status = urb->status; switch (status) { - case 0: + case 0: /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", - __func__, status); - return; - default: - dbg("%s - nonzero urb status received: %d", - __func__, status); - goto exit; + return; + + case -ECONNRESET: + case -ENOENT: + case -ESHUTDOWN: + /* this urb is terminated, clean up */ + dbg("%s - urb shutting down with status: %d", __func__, status); + return; + + default: + dbg("%s - nonzero urb status received: %d", __func__, status); + goto exit; } exit: -- cgit v1.2.3 From 35db715bfd3805b04aa233b9933b9facfa9a3290 Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Sun, 12 Jul 2009 20:51:32 -0700 Subject: Input: pcspkr - switch driver to dev_pm_ops Gets rid of the following warning: Platform driver 'pcspkr' needs updating - please use dev_pm_ops Signed-off-by: Frans Pop Signed-off-by: Dmitry Torokhov --- drivers/input/misc/pcspkr.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/input/misc/pcspkr.c b/drivers/input/misc/pcspkr.c index d6a30cee7bc7..663bbc7ae2f5 100644 --- a/drivers/input/misc/pcspkr.c +++ b/drivers/input/misc/pcspkr.c @@ -113,7 +113,7 @@ static int __devexit pcspkr_remove(struct platform_device *dev) return 0; } -static int pcspkr_suspend(struct platform_device *dev, pm_message_t state) +static int pcspkr_suspend(struct device *dev) { pcspkr_event(NULL, EV_SND, SND_BELL, 0); @@ -126,14 +126,18 @@ static void pcspkr_shutdown(struct platform_device *dev) pcspkr_event(NULL, EV_SND, SND_BELL, 0); } +static struct dev_pm_ops pcspkr_pm_ops = { + .suspend = pcspkr_suspend, +}; + static struct platform_driver pcspkr_platform_driver = { .driver = { .name = "pcspkr", .owner = THIS_MODULE, + .pm = &pcspkr_pm_ops, }, .probe = pcspkr_probe, .remove = __devexit_p(pcspkr_remove), - .suspend = pcspkr_suspend, .shutdown = pcspkr_shutdown, }; -- cgit v1.2.3 From f0a14de2f82dd6aa13e04816da2091c7ed0f77cf Mon Sep 17 00:00:00 2001 From: Simon Davie Date: Sun, 12 Jul 2009 20:44:09 -0700 Subject: Input: atkbd - add forced release keys quirk for FSC Amilo Pi 3525 This patch enables forced releasing of the Fn+Volume hotkeys on the Fujitsu Siemens Amilo Pi 3525 notebook. Signed-off-by: Simon Davie Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/atkbd.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'drivers') diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c index df3f8aa68115..809a7ddbe3af 100644 --- a/drivers/input/keyboard/atkbd.c +++ b/drivers/input/keyboard/atkbd.c @@ -894,6 +894,13 @@ static unsigned int atkbd_amilo_pa1510_forced_release_keys[] = { 0xb0, 0xae, -1U }; +/* + * Amilo Pi 3525 key release for Fn+Volume keys not working + */ +static unsigned int atkbd_amilo_pi3525_forced_release_keys[] = { + 0x20, 0xa0, 0x2e, 0xae, 0x30, 0xb0, -1U +}; + /* * Amilo Xi 3650 key release for light touch bar not working */ @@ -1567,6 +1574,15 @@ static struct dmi_system_id atkbd_dmi_quirk_table[] __initdata = { .callback = atkbd_setup_forced_release, .driver_data = atkbd_amilo_pa1510_forced_release_keys, }, + { + .ident = "Fujitsu Amilo Pi 3525", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU SIEMENS"), + DMI_MATCH(DMI_PRODUCT_NAME, "AMILO Pi 3525"), + }, + .callback = atkbd_setup_forced_release, + .driver_data = atkbd_amilo_pi3525_forced_release_keys, + }, { .ident = "Fujitsu Amilo Xi 3650", .matches = { -- cgit v1.2.3 From 832cc28d5bc676331e6376d940ae45d5937aa688 Mon Sep 17 00:00:00 2001 From: Florian Mickler Date: Mon, 13 Jul 2009 18:40:32 +0800 Subject: drm/i915: Set lvds dual channel according to register from vbios Vbios will set lvds register correctly based on current algorithm for lingle/dual Channel LVDS when system boot, so we can accept this configuration directly, regardless of LVDS enable status. It fixed freedesktop.org bug #22262 Signed-off-by: Florian Mickler Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 508838ee31e0..3371cb0ba81b 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -645,7 +645,7 @@ intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err = target; if (IS_I9XX(dev) && intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) && - (I915_READ(LVDS) & LVDS_PORT_EN) != 0) { + (I915_READ(LVDS)) != 0) { /* * For LVDS, if the panel is on, just rely on its current * settings for dual-channel. We haven't figured out how to -- cgit v1.2.3 From 8a90523639f49dc4b4fa7ae47bb9c8ed73ea8577 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Sat, 11 Jul 2009 16:48:03 -0400 Subject: drm/i915: refactor error detection & collection This patch refactors the existing error detection and collection code, placing most of it in i915_handle_error(). Additionally, we introduce a work queue for scheduling post-crash tasks such as generating a uevent. Using the uevent facility, userspace should be able to capture a post-mortem dump for diagnostics. Signed-off-by: Jesse Barnes Signed-off-by: Ben Gamari Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/i915_gem_debugfs.c | 2 + drivers/gpu/drm/i915/i915_irq.c | 232 ++++++++++++++++++++++---------- 3 files changed, 161 insertions(+), 74 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index d08752875885..b05b44dd3bf6 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -229,6 +229,7 @@ typedef struct drm_i915_private { spinlock_t error_lock; struct drm_i915_error_state *first_error; + struct work_struct error_work; /* Register state */ u8 saveLBB; diff --git a/drivers/gpu/drm/i915/i915_gem_debugfs.c b/drivers/gpu/drm/i915/i915_gem_debugfs.c index 9a44bfcb8139..cb3b97405fbf 100644 --- a/drivers/gpu/drm/i915/i915_gem_debugfs.c +++ b/drivers/gpu/drm/i915/i915_gem_debugfs.c @@ -343,6 +343,8 @@ static int i915_error_state(struct seq_file *m, void *unused) error = dev_priv->first_error; + seq_printf(m, "Time: %ld s %ld us\n", error->time.tv_sec, + error->time.tv_usec); seq_printf(m, "EIR: 0x%08x\n", error->eir); seq_printf(m, " PGTBL_ER: 0x%08x\n", error->pgtbl_er); seq_printf(m, " INSTPM: 0x%08x\n", error->instpm); diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 7ba23a69a0c0..f340b3fd54e6 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -290,6 +290,35 @@ irqreturn_t igdng_irq_handler(struct drm_device *dev) return ret; } +/** + * i915_error_work_func - do process context error handling work + * @work: work struct + * + * Fire an error uevent so userspace can see that a hang or error + * was detected. + */ +static void i915_error_work_func(struct work_struct *work) +{ + drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t, + error_work); + struct drm_device *dev = dev_priv->dev; + char *event_string = "ERROR=1"; + char *envp[] = { event_string, NULL }; + + DRM_DEBUG("generating error event\n"); + + kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, envp); +} + +/** + * i915_capture_error_state - capture an error record for later analysis + * @dev: drm device + * + * Should be called when an error is detected (either a hang or an error + * interrupt) to capture error state from the time of the error. Fills + * out a structure which becomes available in debugfs for user level tools + * to pick up. + */ static void i915_capture_error_state(struct drm_device *dev) { struct drm_i915_private *dev_priv = dev->dev_private; @@ -325,12 +354,137 @@ static void i915_capture_error_state(struct drm_device *dev) error->acthd = I915_READ(ACTHD_I965); } + do_gettimeofday(&error->time); + dev_priv->first_error = error; out: spin_unlock_irqrestore(&dev_priv->error_lock, flags); } +/** + * i915_handle_error - handle an error interrupt + * @dev: drm device + * + * Do some basic checking of regsiter state at error interrupt time and + * dump it to the syslog. Also call i915_capture_error_state() to make + * sure we get a record and make it available in debugfs. Fire a uevent + * so userspace knows something bad happened (should trigger collection + * of a ring dump etc.). + */ +static void i915_handle_error(struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 eir = I915_READ(EIR); + u32 pipea_stats = I915_READ(PIPEASTAT); + u32 pipeb_stats = I915_READ(PIPEBSTAT); + + i915_capture_error_state(dev); + + printk(KERN_ERR "render error detected, EIR: 0x%08x\n", + eir); + + if (IS_G4X(dev)) { + if (eir & (GM45_ERROR_MEM_PRIV | GM45_ERROR_CP_PRIV)) { + u32 ipeir = I915_READ(IPEIR_I965); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR_I965)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR_I965)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE_I965)); + printk(KERN_ERR " INSTPS: 0x%08x\n", + I915_READ(INSTPS)); + printk(KERN_ERR " INSTDONE1: 0x%08x\n", + I915_READ(INSTDONE1)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD_I965)); + I915_WRITE(IPEIR_I965, ipeir); + (void)I915_READ(IPEIR_I965); + } + if (eir & GM45_ERROR_PAGE_TABLE) { + u32 pgtbl_err = I915_READ(PGTBL_ER); + printk(KERN_ERR "page table error\n"); + printk(KERN_ERR " PGTBL_ER: 0x%08x\n", + pgtbl_err); + I915_WRITE(PGTBL_ER, pgtbl_err); + (void)I915_READ(PGTBL_ER); + } + } + + if (IS_I9XX(dev)) { + if (eir & I915_ERROR_PAGE_TABLE) { + u32 pgtbl_err = I915_READ(PGTBL_ER); + printk(KERN_ERR "page table error\n"); + printk(KERN_ERR " PGTBL_ER: 0x%08x\n", + pgtbl_err); + I915_WRITE(PGTBL_ER, pgtbl_err); + (void)I915_READ(PGTBL_ER); + } + } + + if (eir & I915_ERROR_MEMORY_REFRESH) { + printk(KERN_ERR "memory refresh error\n"); + printk(KERN_ERR "PIPEASTAT: 0x%08x\n", + pipea_stats); + printk(KERN_ERR "PIPEBSTAT: 0x%08x\n", + pipeb_stats); + /* pipestat has already been acked */ + } + if (eir & I915_ERROR_INSTRUCTION) { + printk(KERN_ERR "instruction error\n"); + printk(KERN_ERR " INSTPM: 0x%08x\n", + I915_READ(INSTPM)); + if (!IS_I965G(dev)) { + u32 ipeir = I915_READ(IPEIR); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD)); + I915_WRITE(IPEIR, ipeir); + (void)I915_READ(IPEIR); + } else { + u32 ipeir = I915_READ(IPEIR_I965); + + printk(KERN_ERR " IPEIR: 0x%08x\n", + I915_READ(IPEIR_I965)); + printk(KERN_ERR " IPEHR: 0x%08x\n", + I915_READ(IPEHR_I965)); + printk(KERN_ERR " INSTDONE: 0x%08x\n", + I915_READ(INSTDONE_I965)); + printk(KERN_ERR " INSTPS: 0x%08x\n", + I915_READ(INSTPS)); + printk(KERN_ERR " INSTDONE1: 0x%08x\n", + I915_READ(INSTDONE1)); + printk(KERN_ERR " ACTHD: 0x%08x\n", + I915_READ(ACTHD_I965)); + I915_WRITE(IPEIR_I965, ipeir); + (void)I915_READ(IPEIR_I965); + } + } + + I915_WRITE(EIR, eir); + (void)I915_READ(EIR); + eir = I915_READ(EIR); + if (eir) { + /* + * some errors might have become stuck, + * mask them. + */ + DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir); + I915_WRITE(EMR, I915_READ(EMR) | eir); + I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); + } + + schedule_work(&dev_priv->error_work); +} + irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) { struct drm_device *dev = (struct drm_device *) arg; @@ -372,6 +526,9 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) pipea_stats = I915_READ(PIPEASTAT); pipeb_stats = I915_READ(PIPEBSTAT); + if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT) + i915_handle_error(dev); + /* * Clear the PIPE(A|B)STAT regs before the IIR */ @@ -409,80 +566,6 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) I915_READ(PORT_HOTPLUG_STAT); } - if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT) { - u32 eir = I915_READ(EIR); - - i915_capture_error_state(dev); - - printk(KERN_ERR "render error detected, EIR: 0x%08x\n", - eir); - if (eir & I915_ERROR_PAGE_TABLE) { - u32 pgtbl_err = I915_READ(PGTBL_ER); - printk(KERN_ERR "page table error\n"); - printk(KERN_ERR " PGTBL_ER: 0x%08x\n", - pgtbl_err); - I915_WRITE(PGTBL_ER, pgtbl_err); - (void)I915_READ(PGTBL_ER); - } - if (eir & I915_ERROR_MEMORY_REFRESH) { - printk(KERN_ERR "memory refresh error\n"); - printk(KERN_ERR "PIPEASTAT: 0x%08x\n", - pipea_stats); - printk(KERN_ERR "PIPEBSTAT: 0x%08x\n", - pipeb_stats); - /* pipestat has already been acked */ - } - if (eir & I915_ERROR_INSTRUCTION) { - printk(KERN_ERR "instruction error\n"); - printk(KERN_ERR " INSTPM: 0x%08x\n", - I915_READ(INSTPM)); - if (!IS_I965G(dev)) { - u32 ipeir = I915_READ(IPEIR); - - printk(KERN_ERR " IPEIR: 0x%08x\n", - I915_READ(IPEIR)); - printk(KERN_ERR " IPEHR: 0x%08x\n", - I915_READ(IPEHR)); - printk(KERN_ERR " INSTDONE: 0x%08x\n", - I915_READ(INSTDONE)); - printk(KERN_ERR " ACTHD: 0x%08x\n", - I915_READ(ACTHD)); - I915_WRITE(IPEIR, ipeir); - (void)I915_READ(IPEIR); - } else { - u32 ipeir = I915_READ(IPEIR_I965); - - printk(KERN_ERR " IPEIR: 0x%08x\n", - I915_READ(IPEIR_I965)); - printk(KERN_ERR " IPEHR: 0x%08x\n", - I915_READ(IPEHR_I965)); - printk(KERN_ERR " INSTDONE: 0x%08x\n", - I915_READ(INSTDONE_I965)); - printk(KERN_ERR " INSTPS: 0x%08x\n", - I915_READ(INSTPS)); - printk(KERN_ERR " INSTDONE1: 0x%08x\n", - I915_READ(INSTDONE1)); - printk(KERN_ERR " ACTHD: 0x%08x\n", - I915_READ(ACTHD_I965)); - I915_WRITE(IPEIR_I965, ipeir); - (void)I915_READ(IPEIR_I965); - } - } - - I915_WRITE(EIR, eir); - (void)I915_READ(EIR); - eir = I915_READ(EIR); - if (eir) { - /* - * some errors might have become stuck, - * mask them. - */ - DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir); - I915_WRITE(EMR, I915_READ(EMR) | eir); - I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); - } - } - I915_WRITE(IIR, iir); new_iir = I915_READ(IIR); /* Flush posted writes */ @@ -830,6 +913,7 @@ void i915_driver_irq_preinstall(struct drm_device * dev) atomic_set(&dev_priv->irq_received, 0); INIT_WORK(&dev_priv->hotplug_work, i915_hotplug_work_func); + INIT_WORK(&dev_priv->error_work, i915_error_work_func); if (IS_IGDNG(dev)) { igdng_irq_preinstall(dev); -- cgit v1.2.3 From 5e4d6fa72619aeea271d2ad704757717b06e291a Mon Sep 17 00:00:00 2001 From: Keith Packard Date: Sun, 12 Jul 2009 23:53:17 -0700 Subject: drm/i915: Allow frame buffers up to 4096x4096 on 915/945 class hardware The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the existing 2048 max in place. I'm not sure why we limit the height to the same value; there's no intrinsic hardware limit in the scanout engine. Signed-off-by: Keith Packard Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3371cb0ba81b..984645e26a2d 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -3148,6 +3148,9 @@ void intel_modeset_init(struct drm_device *dev) if (IS_I965G(dev)) { dev->mode_config.max_width = 8192; dev->mode_config.max_height = 8192; + } else if (IS_I9XX(dev)) { + dev->mode_config.max_width = 4096; + dev->mode_config.max_height = 4096; } else { dev->mode_config.max_width = 2048; dev->mode_config.max_height = 2048; -- cgit v1.2.3 From ed8c754b292f02d0550596481527b7bf2b52d024 Mon Sep 17 00:00:00 2001 From: Tormod Volden Date: Mon, 13 Jul 2009 22:26:48 +0200 Subject: drm/i915: ignore lvds on AOpen Mini PC MP-915 This motherboard thinks it has an LVDS connected, so without this patch the screen goes blank on the connected VGA monitor. More information (for the non-KMS case) in fd.o bug #18004. Signed-off-by: Tormod Volden Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_lvds.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 9ab38efffecf..43c7d9aa59ce 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -778,6 +778,14 @@ static const struct dmi_system_id intel_no_lvds[] = { DMI_MATCH(DMI_PRODUCT_NAME, "i965GMx-IF"), }, }, + { + .callback = intel_no_lvds_dmi_callback, + .ident = "AOpen Mini PC MP915", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"), + DMI_MATCH(DMI_BOARD_NAME, "i915GMx-F"), + }, + }, { .callback = intel_no_lvds_dmi_callback, .ident = "Aopen i945GTt-VFA", -- cgit v1.2.3 From f936601471d1454dacbd3b2a961fd4d883090aeb Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Mon, 13 Jul 2009 22:22:49 -0700 Subject: Input: fix EVIOCGNAME/JSIOCGNAME regression Commit 3d5cb60e ("Input: simplify name handling for certain input handles") introduced a regression for the EVIOCGNAME/JSIOCGNAME ioctl. Before this, patch, the platform device's name was given back to userspace which was good to identify devices. After this patch, the device is ("event%d", minor) which is not descriptive at all. This fixes the behaviour by taking dev->name. Reported-by: Sven Neumann Signed-off-by: Daniel Mack Reviewed-by: Thadeu Lima de Souza Cascardo Signed-off-by: Dmitry Torokhov --- drivers/input/evdev.c | 3 +-- drivers/input/joydev.c | 2 +- 2 files changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c index 114efd8dc8f5..1148140d08a1 100644 --- a/drivers/input/evdev.c +++ b/drivers/input/evdev.c @@ -608,8 +608,7 @@ static long evdev_do_ioctl(struct file *file, unsigned int cmd, p, compat_mode); if (_IOC_NR(cmd) == _IOC_NR(EVIOCGNAME(0))) - return str_to_user(dev_name(&evdev->dev), - _IOC_SIZE(cmd), p); + return str_to_user(dev->name, _IOC_SIZE(cmd), p); if (_IOC_NR(cmd) == _IOC_NR(EVIOCGPHYS(0))) return str_to_user(dev->phys, _IOC_SIZE(cmd), p); diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c index 0e12f89276a3..4cfd084fa897 100644 --- a/drivers/input/joydev.c +++ b/drivers/input/joydev.c @@ -536,7 +536,7 @@ static int joydev_ioctl_common(struct joydev *joydev, default: if ((cmd & ~IOCSIZE_MASK) == JSIOCGNAME(0)) { int len; - const char *name = dev_name(&dev->dev); + const char *name = dev->name; if (!name) return 0; -- cgit v1.2.3 From dff33cfcefa31c30b72c57f44586754ea9e8f3e2 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Tue, 14 Jul 2009 10:15:56 -0700 Subject: drm/i915: FIFO watermark calculation fixes I discovered several bugs in the FIFO code that was recently applied. Some of them fell into the "how did this ever work" category, since in some cases we were using the wrong FIFO size values, and the calculations ended up being way off. This patch fixes all the bugs I found, and works well on my GM45, 915GM and 855GM test machines; but as usual with these sorts of patches broader testing is definitely requested (in particular this patch affects 830, 845 and 865 for which I don't have test hardware). Overall, the patch clarifies the watermark calculation function by adding some comments and debug info, and making the variable names a bit clearer. The "get FIFO size" portion of the code has also been corrected, so we should be able to properly detect the FIFO allocations for each pipe, for use in the watermark calculation. Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 2 +- drivers/gpu/drm/i915/intel_display.c | 186 +++++++++++++++++++++-------------- 2 files changed, 113 insertions(+), 75 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 6c0858484094..897a116cad14 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1618,7 +1618,7 @@ #define I830_FIFO_LINE_SIZE 32 #define I945_FIFO_SIZE 127 /* 945 & 965 */ #define I915_FIFO_SIZE 95 -#define I855GM_FIFO_SIZE 255 +#define I855GM_FIFO_SIZE 127 /* In cachelines */ #define I830_FIFO_SIZE 95 #define I915_MAX_WM 0x3f diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 984645e26a2d..3fa0d63c83b9 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1623,44 +1623,67 @@ static struct intel_watermark_params igd_cursor_hplloff_wm = { IGD_FIFO_LINE_SIZE }; static struct intel_watermark_params i945_wm_info = { - I915_FIFO_LINE_SIZE, + I945_FIFO_SIZE, I915_MAX_WM, 1, - 0, - IGD_FIFO_LINE_SIZE + 2, + I915_FIFO_LINE_SIZE }; static struct intel_watermark_params i915_wm_info = { - I945_FIFO_SIZE, + I915_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I915_FIFO_LINE_SIZE }; static struct intel_watermark_params i855_wm_info = { I855GM_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I830_FIFO_LINE_SIZE }; static struct intel_watermark_params i830_wm_info = { I830_FIFO_SIZE, I915_MAX_WM, 1, - 0, + 2, I830_FIFO_LINE_SIZE }; +/** + * intel_calculate_wm - calculate watermark level + * @clock_in_khz: pixel clock + * @wm: chip FIFO params + * @pixel_size: display pixel size + * @latency_ns: memory latency for the platform + * + * Calculate the watermark level (the level at which the display plane will + * start fetching from memory again). Each chip has a different display + * FIFO size and allocation, so the caller needs to figure that out and pass + * in the correct intel_watermark_params structure. + * + * As the pixel clock runs, the FIFO will be drained at a rate that depends + * on the pixel size. When it reaches the watermark level, it'll start + * fetching FIFO line sized based chunks from memory until the FIFO fills + * past the watermark point. If the FIFO drains completely, a FIFO underrun + * will occur, and a display engine hang could result. + */ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, struct intel_watermark_params *wm, int pixel_size, unsigned long latency_ns) { - unsigned long bytes_required, wm_size; + unsigned long entries_required, wm_size; + + entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; + entries_required /= wm->cacheline_size; + + DRM_DEBUG("FIFO entries required for mode: %d\n", entries_required); - bytes_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; - bytes_required /= wm->cacheline_size; - wm_size = wm->fifo_size - bytes_required - wm->guard_size; + wm_size = wm->fifo_size - (entries_required + wm->guard_size); + + DRM_DEBUG("FIFO watermark level: %d\n", wm_size); if (wm_size > wm->max_wm) wm_size = wm->max_wm; @@ -1799,8 +1822,37 @@ static void igd_enable_cxsr(struct drm_device *dev, unsigned long clock, return; } -const static int latency_ns = 5000; /* default for non-igd platforms */ +const static int latency_ns = 3000; /* default for non-igd platforms */ + +static int intel_get_fifo_size(struct drm_device *dev, int plane) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + uint32_t dsparb = I915_READ(DSPARB); + int size; + + if (IS_I9XX(dev)) { + if (plane == 0) + size = dsparb & 0x7f; + else + size = ((dsparb >> DSPARB_CSTART_SHIFT) & 0x7f) - + (dsparb & 0x7f); + } else if (IS_I85X(dev)) { + if (plane == 0) + size = dsparb & 0x1ff; + else + size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) - + (dsparb & 0x1ff); + size >>= 1; /* Convert to cachelines */ + } else { + size = dsparb & 0x7f; + size >>= 1; /* Convert to cachelines */ + } + + DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A", + size); + return size; +} static void i965_update_wm(struct drm_device *dev) { @@ -1817,101 +1869,87 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, int planeb_clock, int sr_hdisplay, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; - uint32_t fwater_hi = I915_READ(FW_BLC2) & LM_FIFO_WATERMARK; - int bsize, asize, cwm, bwm = 1, awm = 1, srwm = 1; - uint32_t dsparb = I915_READ(DSPARB); - int planea_entries, planeb_entries; - struct intel_watermark_params *wm_params; + uint32_t fwater_lo; + uint32_t fwater_hi; + int total_size, cacheline_size, cwm, srwm = 1; + int planea_wm, planeb_wm; + struct intel_watermark_params planea_params, planeb_params; unsigned long line_time_us; int sr_clock, sr_entries = 0; + /* Create copies of the base settings for each pipe */ if (IS_I965GM(dev) || IS_I945GM(dev)) - wm_params = &i945_wm_info; + planea_params = planeb_params = i945_wm_info; else if (IS_I9XX(dev)) - wm_params = &i915_wm_info; + planea_params = planeb_params = i915_wm_info; else - wm_params = &i855_wm_info; - - planea_entries = intel_calculate_wm(planea_clock, wm_params, - pixel_size, latency_ns); - planeb_entries = intel_calculate_wm(planeb_clock, wm_params, - pixel_size, latency_ns); + planea_params = planeb_params = i855_wm_info; - DRM_DEBUG("FIFO entries - A: %d, B: %d\n", planea_entries, - planeb_entries); + /* Grab a couple of global values before we overwrite them */ + total_size = planea_params.fifo_size; + cacheline_size = planea_params.cacheline_size; - if (IS_I9XX(dev)) { - asize = dsparb & 0x7f; - bsize = (dsparb >> DSPARB_CSTART_SHIFT) & 0x7f; - } else { - asize = dsparb & 0x1ff; - bsize = (dsparb >> DSPARB_BEND_SHIFT) & 0x1ff; - } - DRM_DEBUG("FIFO size - A: %d, B: %d\n", asize, bsize); + /* Update per-plane FIFO sizes */ + planea_params.fifo_size = intel_get_fifo_size(dev, 0); + planeb_params.fifo_size = intel_get_fifo_size(dev, 1); - /* Two extra entries for padding */ - awm = asize - (planea_entries + 2); - bwm = bsize - (planeb_entries + 2); - - /* Sanity check against potentially bad FIFO allocations */ - if (awm <= 0) { - /* pipe is on but has too few FIFO entries */ - if (planea_entries != 0) - DRM_DEBUG("plane A needs more FIFO entries\n"); - awm = 1; - } - if (bwm <= 0) { - if (planeb_entries != 0) - DRM_DEBUG("plane B needs more FIFO entries\n"); - bwm = 1; - } + planea_wm = intel_calculate_wm(planea_clock, &planea_params, + pixel_size, latency_ns); + planeb_wm = intel_calculate_wm(planeb_clock, &planeb_params, + pixel_size, latency_ns); + DRM_DEBUG("FIFO watermarks - A: %d, B: %d\n", planea_wm, planeb_wm); /* * Overlay gets an aggressive default since video jitter is bad. */ cwm = 2; - /* Calc sr entries for one pipe configs */ + /* Calc sr entries for one plane configs */ if (!planea_clock || !planeb_clock) { + /* self-refresh has much higher latency */ + const static int sr_latency_ns = 6000; + sr_clock = planea_clock ? planea_clock : planeb_clock; - line_time_us = (sr_hdisplay * 1000) / sr_clock; - sr_entries = (((latency_ns / line_time_us) + 1) * pixel_size * - sr_hdisplay) / 1000; - sr_entries = roundup(sr_entries / wm_params->cacheline_size, 1); - if (sr_entries < wm_params->fifo_size) - srwm = wm_params->fifo_size - sr_entries; + line_time_us = ((sr_hdisplay * 1000) / sr_clock); + + /* Use ns/us then divide to preserve precision */ + sr_entries = (((sr_latency_ns / line_time_us) + 1) * + pixel_size * sr_hdisplay) / 1000; + sr_entries = roundup(sr_entries / cacheline_size, 1); + DRM_DEBUG("self-refresh entries: %d\n", sr_entries); + srwm = total_size - sr_entries; + if (srwm < 0) + srwm = 1; } DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n", - awm, bwm, cwm, srwm); + planea_wm, planeb_wm, cwm, srwm); - fwater_lo = fwater_lo | ((bwm & 0x3f) << 16) | (awm & 0x3f); - fwater_hi = fwater_hi | (cwm & 0x1f); + fwater_lo = ((planeb_wm & 0x3f) << 16) | (planea_wm & 0x3f); + fwater_hi = (cwm & 0x1f); + + /* Set request length to 8 cachelines per fetch */ + fwater_lo = fwater_lo | (1 << 24) | (1 << 8); + fwater_hi = fwater_hi | (1 << 8); I915_WRITE(FW_BLC, fwater_lo); I915_WRITE(FW_BLC2, fwater_hi); if (IS_I9XX(dev)) - I915_WRITE(FW_BLC_SELF, FW_BLC_SELF_EN | (srwm & 0x3f)); + I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } static void i830_update_wm(struct drm_device *dev, int planea_clock, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t dsparb = I915_READ(DSPARB); uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; - unsigned int asize, awm; - int planea_entries; - - planea_entries = intel_calculate_wm(planea_clock, &i830_wm_info, - pixel_size, latency_ns); - - asize = dsparb & 0x7f; + int planea_wm; - awm = asize - planea_entries; + i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0); - fwater_lo = fwater_lo | awm; + planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info, + pixel_size, latency_ns); + fwater_lo = fwater_lo | planea_wm; I915_WRITE(FW_BLC, fwater_lo); } @@ -1984,7 +2022,7 @@ static void intel_update_watermarks(struct drm_device *dev) if (enabled <= 0) return; - /* Single pipe configs can enable self refresh */ + /* Single plane configs can enable self refresh */ if (enabled == 1 && IS_IGD(dev)) igd_enable_cxsr(dev, sr_clock, pixel_size); else if (IS_IGD(dev)) -- cgit v1.2.3 From c9d4bc289cd1cd43c3cff97b73efe2b0b5098a92 Mon Sep 17 00:00:00 2001 From: Zhaolei Date: Tue, 14 Jul 2009 17:59:05 +0800 Subject: z2ram: Small cleanup for z2ram.c We should use Z2MINOR_COUNT as range argument in blk_unregister_region() Signed-off-by: Zhao Lei Signed-off-by: Tejun Heo --- drivers/block/z2ram.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/block/z2ram.c b/drivers/block/z2ram.c index 4575171e5beb..b2590409f25e 100644 --- a/drivers/block/z2ram.c +++ b/drivers/block/z2ram.c @@ -374,7 +374,7 @@ err: static void __exit z2_exit(void) { int i, j; - blk_unregister_region(MKDEV(Z2RAM_MAJOR, 0), 256); + blk_unregister_region(MKDEV(Z2RAM_MAJOR, 0), Z2MINOR_COUNT); unregister_blkdev(Z2RAM_MAJOR, DEVICE_NAME); del_gendisk(z2ram_gendisk); put_disk(z2ram_gendisk); -- cgit v1.2.3 From fe2c4d018fc6127610fef677e020b3bb41cfaaaf Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 8 Jul 2009 12:16:37 +0900 Subject: libata: fix follow-up SRST failure path ata_eh_reset() was missing error return handling after follow-up SRST allowing EH to continue the normal probing path after reset failure. This was discovered while testing new WD 2TB drives which take longer than 10 secs to spin up and cause the first follow-up SRST to time out. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index fa22f94ca415..1a07c061f644 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2517,6 +2517,10 @@ int ata_eh_reset(struct ata_link *link, int classify, ata_eh_about_to_do(link, NULL, ATA_EH_RESET); rc = ata_do_reset(link, reset, classes, deadline, true); + if (rc) { + failed_link = link; + goto fail; + } } } else { if (verbose) -- cgit v1.2.3 From d0cb43b35d64877b2944bd37719708be5d7bbf99 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Thu, 9 Jul 2009 09:27:50 +0900 Subject: libata: implement and use HORKAGE_NOSETXFER, take#2 PIONEER DVD-RW DVRTD08 times out SETXFER if no media is present. The device is SATA and simply skipping SETXFER works around the problem. Implement ATA_HORKAGE_NOSETXFER and apply it to the device. Reported by Moritz Rigler in the following thread. http://thread.gmane.org/gmane.linux.ide/36790 and by Lars in bko#9540. Updated to whine and ignore NOSETXFER if PATA component is detected as suggested by Alan Cox. Signed-off-by: Tejun Heo Reported-by: Moritz Rigler Reported-by: Lars Cc: Alan Cox Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 20 ++++++++++++++++++-- include/linux/libata.h | 1 + 2 files changed, 19 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 045a486a09ea..2c6aedaef718 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -3392,17 +3392,27 @@ int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel) static int ata_dev_set_mode(struct ata_device *dev) { + struct ata_port *ap = dev->link->ap; struct ata_eh_context *ehc = &dev->link->eh_context; + const bool nosetxfer = dev->horkage & ATA_HORKAGE_NOSETXFER; const char *dev_err_whine = ""; int ign_dev_err = 0; - unsigned int err_mask; + unsigned int err_mask = 0; int rc; dev->flags &= ~ATA_DFLAG_PIO; if (dev->xfer_shift == ATA_SHIFT_PIO) dev->flags |= ATA_DFLAG_PIO; - err_mask = ata_dev_set_xfermode(dev); + if (nosetxfer && ap->flags & ATA_FLAG_SATA && ata_id_is_sata(dev->id)) + dev_err_whine = " (SET_XFERMODE skipped)"; + else { + if (nosetxfer) + ata_dev_printk(dev, KERN_WARNING, + "NOSETXFER but PATA detected - can't " + "skip SETXFER, might malfunction\n"); + err_mask = ata_dev_set_xfermode(dev); + } if (err_mask & ~AC_ERR_DEV) goto fail; @@ -4297,6 +4307,12 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { /* Devices which aren't very happy with higher link speeds */ { "WD My Book", NULL, ATA_HORKAGE_1_5_GBPS, }, + /* + * Devices which choke on SETXFER. Applies only if both the + * device and controller are SATA. + */ + { "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER }, + /* End Marker */ { } }; diff --git a/include/linux/libata.h b/include/linux/libata.h index 3d501db36a26..79b6d7fd4ac2 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -385,6 +385,7 @@ enum { not multiple of 16 bytes */ ATA_HORKAGE_FIRMWARE_WARN = (1 << 12), /* firmware update warning */ ATA_HORKAGE_1_5_GBPS = (1 << 13), /* force 1.5 Gbps */ + ATA_HORKAGE_NOSETXFER = (1 << 14), /* skip SETXFER, SATA only */ /* DMA mask for user DMA control: User visible values; DO NOT renumber */ -- cgit v1.2.3 From 1e1f421a8137824127a41303a30493356b5da638 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 11 Jul 2009 09:49:48 +0200 Subject: drivers/ata: Move a dereference below a NULL test If the NULL test is necessary, then the dereference should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E when != i if (E == NULL) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: Jeff Garzik --- drivers/ata/pata_at91.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 4b27617be26d..8561a9f195c1 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -312,11 +312,12 @@ err_ide_ioremap: static int __devexit pata_at91_remove(struct platform_device *pdev) { struct ata_host *host = dev_get_drvdata(&pdev->dev); - struct at91_ide_info *info = host->private_data; + struct at91_ide_info *info; struct device *dev = &pdev->dev; if (!host) return 0; + info = host->private_data; ata_host_detach(host); -- cgit v1.2.3 From b2dde6afe5d29212d521e69492ebc299db235001 Mon Sep 17 00:00:00 2001 From: Mark Goodwin Date: Fri, 26 Jun 2009 10:44:11 -0500 Subject: ahci: add device ID for 82801JI sata controller Add device ID for Intel 82801JI SATA AHCI controller. Signed-off-by: David Milburn Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 15a23031833f..336eb1ed73cc 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -513,6 +513,7 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x502a), board_ahci }, /* Tolapai */ { PCI_VDEVICE(INTEL, 0x502b), board_ahci }, /* Tolapai */ { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */ + { PCI_VDEVICE(INTEL, 0x3a22), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */ { PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */ -- cgit v1.2.3 From d25e3a6faa82eeaa6e5487c2d2e27cfd938ed108 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Mon, 13 Jul 2009 23:20:20 +0200 Subject: drm: drm_debugfs, check kmalloc retval Check kmalloc return value in drm_debugfs_create_files and bail out appropriately if the pointer is NULL. Signed-off-by: Jiri Slaby Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_debugfs.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_debugfs.c b/drivers/gpu/drm/drm_debugfs.c index 2960b6d73456..9903f270e440 100644 --- a/drivers/gpu/drm/drm_debugfs.c +++ b/drivers/gpu/drm/drm_debugfs.c @@ -101,6 +101,10 @@ int drm_debugfs_create_files(struct drm_info_list *files, int count, continue; tmp = kmalloc(sizeof(struct drm_info_node), GFP_KERNEL); + if (tmp == NULL) { + ret = -1; + goto fail; + } ent = debugfs_create_file(files[i].name, S_IFREG | S_IRUGO, root, tmp, &drm_debugfs_fops); if (!ent) { -- cgit v1.2.3 From 845792d940f5755b7a7837c450a71d9e831a13e2 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Mon, 13 Jul 2009 23:20:21 +0200 Subject: drm: drm_gem, check kzalloc retval Check kzalloc retval against NULL in drm_gem_object_alloc and bail out appropriately. While at it merge the fail paths and jump to them by gotos at the end of the function. Signed-off-by: Jiri Slaby Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_gem.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_gem.c b/drivers/gpu/drm/drm_gem.c index 8104ecaea26f..ffe8f4394d50 100644 --- a/drivers/gpu/drm/drm_gem.c +++ b/drivers/gpu/drm/drm_gem.c @@ -134,26 +134,29 @@ drm_gem_object_alloc(struct drm_device *dev, size_t size) BUG_ON((size & (PAGE_SIZE - 1)) != 0); obj = kzalloc(sizeof(*obj), GFP_KERNEL); + if (!obj) + goto free; obj->dev = dev; obj->filp = shmem_file_setup("drm mm object", size, VM_NORESERVE); - if (IS_ERR(obj->filp)) { - kfree(obj); - return NULL; - } + if (IS_ERR(obj->filp)) + goto free; kref_init(&obj->refcount); kref_init(&obj->handlecount); obj->size = size; if (dev->driver->gem_init_object != NULL && dev->driver->gem_init_object(obj) != 0) { - fput(obj->filp); - kfree(obj); - return NULL; + goto fput; } atomic_inc(&dev->object_count); atomic_add(obj->size, &dev->object_memory); return obj; +fput: + fput(obj->filp); +free: + kfree(obj); + return NULL; } EXPORT_SYMBOL(drm_gem_object_alloc); -- cgit v1.2.3 From 42dd8619940a153e950c4d2301cd5e49f7342f99 Mon Sep 17 00:00:00 2001 From: Simon Farnsworth Date: Fri, 10 Jul 2009 11:25:16 +0100 Subject: drm/via: Fix vblank IRQ on VIA hardware. via_enable_vblank wasn't setting the VBlank enable bit - instead, it was masking out the rest of the register. At the same time, fix via_disable_vblank to clear the VBlank enable bit. Signed-off-by: Dave Airlie --- drivers/gpu/drm/via/via_irq.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/via/via_irq.c b/drivers/gpu/drm/via/via_irq.c index c248c1d37268..5935b8842e86 100644 --- a/drivers/gpu/drm/via/via_irq.c +++ b/drivers/gpu/drm/via/via_irq.c @@ -183,7 +183,7 @@ int via_enable_vblank(struct drm_device *dev, int crtc) } status = VIA_READ(VIA_REG_INTERRUPT); - VIA_WRITE(VIA_REG_INTERRUPT, status & VIA_IRQ_VBLANK_ENABLE); + VIA_WRITE(VIA_REG_INTERRUPT, status | VIA_IRQ_VBLANK_ENABLE); VIA_WRITE8(0x83d4, 0x11); VIA_WRITE8(0x83d5, VIA_READ8(0x83d5) | 0x30); @@ -194,6 +194,10 @@ int via_enable_vblank(struct drm_device *dev, int crtc) void via_disable_vblank(struct drm_device *dev, int crtc) { drm_via_private_t *dev_priv = dev->dev_private; + u32 status; + + status = VIA_READ(VIA_REG_INTERRUPT); + VIA_WRITE(VIA_REG_INTERRUPT, status & ~VIA_IRQ_VBLANK_ENABLE); VIA_WRITE8(0x83d4, 0x11); VIA_WRITE8(0x83d5, VIA_READ8(0x83d5) & ~0x30); -- cgit v1.2.3 From 916635bfcae5fec170ccd36f4b451cf7c5d23b9d Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 15 Jul 2009 16:00:37 +1000 Subject: drm/ttm: fix misplaced parentheses Signed-off-by: Roel Kluin Signed-off-by: Andrew Morton Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_vm.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo_vm.c b/drivers/gpu/drm/ttm/ttm_bo_vm.c index 40b75032ea47..fe949a12fe40 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_vm.c +++ b/drivers/gpu/drm/ttm/ttm_bo_vm.c @@ -327,7 +327,7 @@ ssize_t ttm_bo_io(struct ttm_bo_device *bdev, struct file *filp, goto out_unref; kmap_offset = dev_offset - bo->vm_node->start; - if (unlikely(kmap_offset) >= bo->num_pages) { + if (unlikely(kmap_offset >= bo->num_pages)) { ret = -EFBIG; goto out_unref; } @@ -401,7 +401,7 @@ ssize_t ttm_bo_fbdev_io(struct ttm_buffer_object *bo, const char __user *wbuf, bool dummy; kmap_offset = (*f_pos >> PAGE_SHIFT); - if (unlikely(kmap_offset) >= bo->num_pages) + if (unlikely(kmap_offset >= bo->num_pages)) return -EFBIG; page_offset = *f_pos & ~PAGE_MASK; -- cgit v1.2.3 From ba0ab82358a12e7a7f2872d6b65c437157c6888f Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Fri, 3 Jul 2009 11:24:46 -0700 Subject: fb/intelfb: conflict with DRM_I915 and hide by default Users get confused by this driver. It's really a special purpose embedded driver, and causes a lot of problems if enabled. So hide it under EMBEDDED by default, and make sure it doesn't get enabled with the i915 DRM driver. Dave, I'm hoping you can feed this to Linus through your tree. It's appropriate for 2.6.31 I think. Signed-off-by: Jesse Barnes Signed-off-by: Dave Airlie --- drivers/video/Kconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 8afcf08eba98..3b54b3940178 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -1119,12 +1119,13 @@ config FB_CARILLO_RANCH config FB_INTEL tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)" - depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL + depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL && EMBEDDED select FB_MODE_HELPERS select FB_CFB_FILLRECT select FB_CFB_COPYAREA select FB_CFB_IMAGEBLIT select FB_BOOT_VESA_SUPPORT if FB_INTEL = y + depends on !DRM_I915 help This driver supports the on-board graphics built in to the Intel 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets. -- cgit v1.2.3 From ecca0683230b83e8f830ff157911fad20bc43015 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 11 Jul 2009 09:50:09 +0200 Subject: drm: Move a dereference below a NULL test If the NULL test is necessary, then the dereference should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E when != i if (E == NULL) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_stub.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_stub.c b/drivers/gpu/drm/drm_stub.c index 155a5bbce680..55bb8a82d612 100644 --- a/drivers/gpu/drm/drm_stub.c +++ b/drivers/gpu/drm/drm_stub.c @@ -489,7 +489,7 @@ int drm_put_minor(struct drm_minor **minor_p) */ void drm_put_dev(struct drm_device *dev) { - struct drm_driver *driver = dev->driver; + struct drm_driver *driver; struct drm_map_list *r_list, *list_temp; DRM_DEBUG("\n"); @@ -498,6 +498,7 @@ void drm_put_dev(struct drm_device *dev) DRM_ERROR("cleanup called no dev\n"); return; } + driver = dev->driver; drm_vblank_cleanup(dev); -- cgit v1.2.3 From ed10f95d60d41033d356fdcf88c240d7065bd5b4 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:11 +1000 Subject: drm/radeon/kms: fix some GART table entry bugs. 1. rv370 can accept 40-bit addresses - also at 24-bit shift not 4 bits 2. rs480 table can be in 40-bit space. - 4 bit shift for top 8 bits 3. rs480 table entries can be in 40-bit space. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 2 +- drivers/gpu/drm/radeon/r300.c | 4 +++- drivers/gpu/drm/radeon/radeon_gart.c | 2 +- drivers/gpu/drm/radeon/rs400.c | 13 +++++++++++-- 4 files changed, 16 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index c550932a108f..1b23106f9552 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -110,7 +110,7 @@ int r100_pci_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - rdev->gart.table.ram.ptr[i] = cpu_to_le32((uint32_t)addr); + rdev->gart.table.ram.ptr[i] = cpu_to_le32(lower_32_bits(addr)); return 0; } diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index e2ed5bc08170..cd9ea98e9c6f 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -150,7 +150,9 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - addr = (((u32)addr) >> 8) | ((upper_32_bits(addr) & 0xff) << 4) | 0xC; + addr = (lower_32_bits(addr) >> 8) | + ((upper_32_bits(addr) & 0xff) << 24) | + 0xc; writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4)); return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_gart.c b/drivers/gpu/drm/radeon/radeon_gart.c index d343a15316ec..2977539880fb 100644 --- a/drivers/gpu/drm/radeon/radeon_gart.c +++ b/drivers/gpu/drm/radeon/radeon_gart.c @@ -177,7 +177,7 @@ int radeon_gart_bind(struct radeon_device *rdev, unsigned offset, return -ENOMEM; } rdev->gart.pages[p] = pagelist[i]; - page_base = (uint32_t)rdev->gart.pages_addr[p]; + page_base = rdev->gart.pages_addr[p]; for (j = 0; j < (PAGE_SIZE / 4096); j++, t++) { radeon_gart_set_page(rdev, t, page_base); page_base += 4096; diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index cc074b5a8f74..3275de4b6e3b 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -164,7 +164,9 @@ int rs400_gart_enable(struct radeon_device *rdev) WREG32(RADEON_BUS_CNTL, tmp); } /* Table should be in 32bits address space so ignore bits above. */ - tmp = rdev->gart.table_addr & 0xfffff000; + tmp = (u32)rdev->gart.table_addr & 0xfffff000; + tmp |= (upper_32_bits(rdev->gart.table_addr) & 0xff) << 4; + WREG32_MC(RS480_GART_BASE, tmp); /* TODO: more tweaking here */ WREG32_MC(RS480_GART_FEATURE_ID, @@ -201,10 +203,17 @@ void rs400_gart_disable(struct radeon_device *rdev) int rs400_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) { + uint32_t entry; + if (i < 0 || i > rdev->gart.num_gpu_pages) { return -EINVAL; } - rdev->gart.table.ram.ptr[i] = cpu_to_le32(((uint32_t)addr) | 0xC); + + entry = (lower_32_bits(addr) & PAGE_MASK) | + ((upper_32_bits(addr) & 0xff) << 4) | + 0xc; + entry = cpu_to_le32(entry); + rdev->gart.table.ram.ptr[i] = entry; return 0; } -- cgit v1.2.3 From 4c9bc75cbc6f2f447a38a123aa6e0605fab3cb7a Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:12 +1000 Subject: drm/radeon/kms: mmio base/size should be resource_size_t. Unsigned long is incorrect for 64-bit resources on 32-bit hw. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index d61f2fc61df5..e7662ba9abfb 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -594,8 +594,8 @@ struct radeon_device { struct radeon_object *fbdev_robj; struct radeon_framebuffer *fbdev_rfb; /* Register mmio */ - unsigned long rmmio_base; - unsigned long rmmio_size; + resource_size_t rmmio_base; + resource_size_t rmmio_size; void *rmmio; radeon_rreg_t mm_rreg; radeon_wreg_t mm_wreg; -- cgit v1.2.3 From 6cdf65855cf884712532fc72770baaef7bdf1b9a Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 18:29:13 +1000 Subject: drm/radeon/kms: remove IB flushing trick. If there is a problem then this is hiding it, we shouldn't ever need to flush the IB. Either the buffers are: WB - caching just works. WC - no need to do explicit flush, the MB + readback will do it Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_ring.c | 15 +-------------- 1 file changed, 1 insertion(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_ring.c b/drivers/gpu/drm/radeon/radeon_ring.c index a853261d1881..60d159308b88 100644 --- a/drivers/gpu/drm/radeon/radeon_ring.c +++ b/drivers/gpu/drm/radeon/radeon_ring.c @@ -126,32 +126,19 @@ static void radeon_ib_align(struct radeon_device *rdev, struct radeon_ib *ib) } } -static void radeon_ib_cpu_flush(struct radeon_device *rdev, - struct radeon_ib *ib) -{ - unsigned long tmp; - unsigned i; - - /* To force CPU cache flush ugly but seems reliable */ - for (i = 0; i < ib->length_dw; i += (rdev->cp.align_mask + 1)) { - tmp = readl(&ib->ptr[i]); - } -} - int radeon_ib_schedule(struct radeon_device *rdev, struct radeon_ib *ib) { int r = 0; mutex_lock(&rdev->ib_pool.mutex); radeon_ib_align(rdev, ib); - radeon_ib_cpu_flush(rdev, ib); if (!ib->length_dw || !rdev->cp.ready) { /* TODO: Nothings in the ib we should report. */ mutex_unlock(&rdev->ib_pool.mutex); DRM_ERROR("radeon: couldn't schedule IB(%lu).\n", ib->idx); return -EINVAL; } - /* 64 dwords should be enought for fence too */ + /* 64 dwords should be enough for fence too */ r = radeon_ring_lock(rdev, 64); if (r) { DRM_ERROR("radeon: scheduling IB failled (%d).\n", r); -- cgit v1.2.3 From 4162338a1dab388474d4115289d1d7071623f04d Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 15:04:19 +1000 Subject: drm/radeon/kms: set crtc and cursor offsets correctly on legacy chips. The crtc and cursor offsets on the legacy chips are offset from DISPLAY_BASE_ADDR. The code worked if display base addr was at 0, but otherwise falls to pieces. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cursor.c | 2 +- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 11 +++++++---- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 3 files changed, 9 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c index 5232441f119b..5f8ce370c4f8 100644 --- a/drivers/gpu/drm/radeon/radeon_cursor.c +++ b/drivers/gpu/drm/radeon/radeon_cursor.c @@ -113,7 +113,7 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj, WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr); else /* offset is from DISP(2)_BASE_ADDRESS */ - WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, gpu_addr); + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr)); } int radeon_crtc_cursor_set(struct drm_crtc *crtc, diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 8086ecf7f03d..14c1a5107fc9 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -244,7 +244,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, if (radeon_gem_object_pin(obj, RADEON_GEM_DOMAIN_VRAM, &base)) { return -EINVAL; } - crtc_offset = (u32)base; + /* if scanout was in GTT this really wouldn't work */ + /* crtc offset is from display base addr not FB location */ + radeon_crtc->legacy_display_base_addr = rdev->mc.vram_location; + + base -= radeon_crtc->legacy_display_base_addr; + crtc_offset_cntl = 0; pitch_pixels = crtc->fb->pitch / (crtc->fb->bits_per_pixel / 8); @@ -303,11 +308,9 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, base &= ~7; - /* update sarea TODO */ - crtc_offset = (u32)base; - WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, rdev->mc.vram_location); + WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, radeon_crtc->legacy_display_base_addr); if (ASIC_IS_R300(rdev)) { if (radeon_crtc->crtc_id) diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 9173b687462b..86f766e868e7 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -185,6 +185,7 @@ struct radeon_crtc { uint64_t cursor_addr; int cursor_width; int cursor_height; + uint32_t legacy_display_base_addr; }; #define RADEON_USE_RMX 1 -- cgit v1.2.3 From 3e43d82125952826202a8cd20ba84a66f3ff8808 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 15:04:18 +1000 Subject: drm/radeon/kms: respect TOM on rs100->rs480 IGP variants. Normally we are free to place VRAM where we want in the GPUs memory address space, however on IGP chips the VRAM is actual RAM, and no special translation or aperture is used inside the GPU MC. So when you move the VRAM aperture away from the TOM register, you actually move it into main memory and can trash things quite badly. This commit makes the code respect the TOM location for MC_FB_LOCATION. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 5 ++++- drivers/gpu/drm/radeon/rs400.c | 6 ++++-- 2 files changed, 8 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 1b23106f9552..a3db56bb013d 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -215,7 +215,6 @@ int r100_mc_init(struct radeon_device *rdev) r100_pci_gart_disable(rdev); /* Setup GPU memory space */ - rdev->mc.vram_location = 0xFFFFFFFFUL; rdev->mc.gtt_location = 0xFFFFFFFFUL; if (rdev->flags & RADEON_IS_AGP) { r = radeon_agp_init(rdev); @@ -1265,6 +1264,8 @@ void r100_vram_info(struct radeon_device *rdev) /* read NB_TOM to get the amount of ram stolen for the GPU */ tom = RREG32(RADEON_NB_TOM); rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); + /* for IGPs we need to keep VRAM where it was put by the BIOS */ + rdev->mc.vram_location = (tom & 0xffff) << 16; WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); } else { rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); @@ -1275,6 +1276,8 @@ void r100_vram_info(struct radeon_device *rdev) rdev->mc.vram_size = 8192 * 1024; WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); } + /* let driver place VRAM */ + rdev->mc.vram_location = 0xFFFFFFFFUL; } rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index 3275de4b6e3b..a18d053065c0 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -235,7 +235,6 @@ int rs400_mc_init(struct radeon_device *rdev) rdev->mc.gtt_location = rdev->mc.vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); - rdev->mc.vram_location = 0xFFFFFFFFUL; r = radeon_mc_setup(rdev); if (r) { return r; @@ -305,7 +304,10 @@ void rs400_vram_info(struct radeon_device *rdev) rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - /* Could aper size report 0 ? */ + /* RS480 IGPs don't seem to translate to main RAM, they + * just reserve and scan out of it. So setting VRAM location + * to say 0, will actually trash the OS. */ + rdev->mc.vram_location = (tom & 0xffff) << 16; rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); } -- cgit v1.2.3 From 531369e62649bb8f31217cc0bf33ee6f89f1dff6 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 29 Jun 2009 11:21:25 +1000 Subject: drm/radeon: fix support for vline relocations. Userspace sends us a special relocation type to sync video/exa to vlines to avoid tearing, this deals with the relocation in the kernel, it picks the correct crtc and avoids issues where crtcs are disabled. This version also parses the wait until to make sure it isn't trying to do anything evil. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 105 ++++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/radeon/r300.c | 13 ++++- drivers/gpu/drm/radeon/r500_reg.h | 2 + drivers/gpu/drm/radeon/rv515.c | 23 +++++++-- 4 files changed, 137 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index a3db56bb013d..154648a2c027 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -751,6 +751,102 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p, return 0; } +/** + * r100_cs_packet_next_vline() - parse userspace VLINE packet + * @parser: parser structure holding parsing context. + * + * Userspace sends a special sequence for VLINE waits. + * PACKET0 - VLINE_START_END + value + * PACKET0 - WAIT_UNTIL +_value + * RELOC (P3) - crtc_id in reloc. + * + * This function parses this and relocates the VLINE START END + * and WAIT UNTIL packets to the correct crtc. + * It also detects a switched off crtc and nulls out the + * wait in that case. + */ +int r100_cs_packet_parse_vline(struct radeon_cs_parser *p) +{ + struct radeon_cs_chunk *ib_chunk; + struct drm_mode_object *obj; + struct drm_crtc *crtc; + struct radeon_crtc *radeon_crtc; + struct radeon_cs_packet p3reloc, waitreloc; + int crtc_id; + int r; + uint32_t header, h_idx, reg; + + ib_chunk = &p->chunks[p->chunk_ib_idx]; + + /* parse the wait until */ + r = r100_cs_packet_parse(p, &waitreloc, p->idx); + if (r) + return r; + + /* check its a wait until and only 1 count */ + if (waitreloc.reg != RADEON_WAIT_UNTIL || + waitreloc.count != 0) { + DRM_ERROR("vline wait had illegal wait until segment\n"); + r = -EINVAL; + return r; + } + + if (ib_chunk->kdata[waitreloc.idx + 1] != RADEON_WAIT_CRTC_VLINE) { + DRM_ERROR("vline wait had illegal wait until\n"); + r = -EINVAL; + return r; + } + + /* jump over the NOP */ + r = r100_cs_packet_parse(p, &p3reloc, p->idx); + if (r) + return r; + + h_idx = p->idx - 2; + p->idx += waitreloc.count; + p->idx += p3reloc.count; + + header = ib_chunk->kdata[h_idx]; + crtc_id = ib_chunk->kdata[h_idx + 5]; + reg = ib_chunk->kdata[h_idx] >> 2; + mutex_lock(&p->rdev->ddev->mode_config.mutex); + obj = drm_mode_object_find(p->rdev->ddev, crtc_id, DRM_MODE_OBJECT_CRTC); + if (!obj) { + DRM_ERROR("cannot find crtc %d\n", crtc_id); + r = -EINVAL; + goto out; + } + crtc = obj_to_crtc(obj); + radeon_crtc = to_radeon_crtc(crtc); + crtc_id = radeon_crtc->crtc_id; + + if (!crtc->enabled) { + /* if the CRTC isn't enabled - we need to nop out the wait until */ + ib_chunk->kdata[h_idx + 2] = PACKET2(0); + ib_chunk->kdata[h_idx + 3] = PACKET2(0); + } else if (crtc_id == 1) { + switch (reg) { + case AVIVO_D1MODE_VLINE_START_END: + header &= R300_CP_PACKET0_REG_MASK; + header |= AVIVO_D2MODE_VLINE_START_END >> 2; + break; + case RADEON_CRTC_GUI_TRIG_VLINE: + header &= R300_CP_PACKET0_REG_MASK; + header |= RADEON_CRTC2_GUI_TRIG_VLINE >> 2; + break; + default: + DRM_ERROR("unknown crtc reloc\n"); + r = -EINVAL; + goto out; + } + ib_chunk->kdata[h_idx] = header; + ib_chunk->kdata[h_idx + 3] |= RADEON_ENG_DISPLAY_SELECT_CRTC1; + } +out: + mutex_unlock(&p->rdev->ddev->mode_config.mutex); + return r; +} + /** * r100_cs_packet_next_reloc() - parse next packet which should be reloc packet3 * @parser: parser structure holding parsing context. @@ -824,6 +920,15 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } for (i = 0; i <= pkt->count; i++, idx++, reg += 4) { switch (reg) { + case RADEON_CRTC_GUI_TRIG_VLINE: + r = r100_cs_packet_parse_vline(p); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + break; /* FIXME: only allow PACKET3 blit? easier to check for out of * range access */ case RADEON_DST_PITCH_OFFSET: diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index cd9ea98e9c6f..656d9238bb06 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -44,6 +44,7 @@ int r100_gui_wait_for_idle(struct radeon_device *rdev); int r100_cs_packet_parse(struct radeon_cs_parser *p, struct radeon_cs_packet *pkt, unsigned idx); +int r100_cs_packet_parse_vline(struct radeon_cs_parser *p); int r100_cs_packet_next_reloc(struct radeon_cs_parser *p, struct radeon_cs_reloc **cs_reloc); int r100_cs_parse_packet0(struct radeon_cs_parser *p, @@ -972,7 +973,7 @@ static inline void r300_cs_track_clear(struct r300_cs_track *track) static const unsigned r300_reg_safe_bm[159] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, @@ -1029,6 +1030,16 @@ static int r300_packet0_check(struct radeon_cs_parser *p, ib_chunk = &p->chunks[p->chunk_ib_idx]; track = (struct r300_cs_track*)p->track; switch(reg) { + case AVIVO_D1MODE_VLINE_START_END: + case RADEON_CRTC_GUI_TRIG_VLINE: + r = r100_cs_packet_parse_vline(p); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + break; case RADEON_DST_PITCH_OFFSET: case RADEON_SRC_PITCH_OFFSET: r = r100_cs_packet_next_reloc(p, &reloc); diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h index 9070a1c2ce23..036691b38cb7 100644 --- a/drivers/gpu/drm/radeon/r500_reg.h +++ b/drivers/gpu/drm/radeon/r500_reg.h @@ -445,6 +445,7 @@ #define AVIVO_D1MODE_DATA_FORMAT 0x6528 # define AVIVO_D1MODE_INTERLEAVE_EN (1 << 0) #define AVIVO_D1MODE_DESKTOP_HEIGHT 0x652C +#define AVIVO_D1MODE_VLINE_START_END 0x6538 #define AVIVO_D1MODE_VIEWPORT_START 0x6580 #define AVIVO_D1MODE_VIEWPORT_SIZE 0x6584 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6588 @@ -496,6 +497,7 @@ #define AVIVO_D2CUR_SIZE 0x6c10 #define AVIVO_D2CUR_POSITION 0x6c14 +#define AVIVO_D2MODE_VLINE_START_END 0x6d38 #define AVIVO_D2MODE_VIEWPORT_START 0x6d80 #define AVIVO_D2MODE_VIEWPORT_SIZE 0x6d84 #define AVIVO_D2MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6d88 diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index ffea37b1b3e2..d1384d3991ad 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -509,9 +509,9 @@ int rv515_debugfs_ga_info_init(struct radeon_device *rdev) /* * Asic initialization */ -static const unsigned r500_reg_safe_bm[159] = { +static const unsigned r500_reg_safe_bm[219] = { + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, - 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, @@ -549,11 +549,24 @@ static const unsigned r500_reg_safe_bm[159] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFF80FFFF, 0x00000000, 0x00000000, 0x00000000, 0x00000000, - 0x0003FC01, 0x3FFFFCF8, 0xFE800B19, + 0x0003FC01, 0x3FFFFCF8, 0xFE800B19, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, }; - - int rv515_init(struct radeon_device *rdev) { rdev->config.r300.reg_safe_bm = r500_reg_safe_bm; -- cgit v1.2.3 From ae3e8122cbf8f9301369f276f4179aa6ec1b5b9c Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Wed, 24 Jun 2009 19:57:34 +0200 Subject: ttm: Fix caching mode selection. A bug caused a new caching state to be selected on each buffer object validation regardless of the current caching state. Moreover, a caching state could be selected that wasn't supported by the memory type. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 51 +++++++++++++++++++++++++++++++++----------- 1 file changed, 39 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index c1c407f7cca3..a753598a5e35 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -655,31 +655,52 @@ retry_pre_get: return 0; } +static uint32_t ttm_bo_select_caching(struct ttm_mem_type_manager *man, + uint32_t cur_placement, + uint32_t proposed_placement) +{ + uint32_t caching = proposed_placement & TTM_PL_MASK_CACHING; + uint32_t result = proposed_placement & ~TTM_PL_MASK_CACHING; + + /** + * Keep current caching if possible. + */ + + if ((cur_placement & caching) != 0) + result |= (cur_placement & caching); + else if ((man->default_caching & caching) != 0) + result |= man->default_caching; + else if ((TTM_PL_FLAG_CACHED & caching) != 0) + result |= TTM_PL_FLAG_CACHED; + else if ((TTM_PL_FLAG_WC & caching) != 0) + result |= TTM_PL_FLAG_WC; + else if ((TTM_PL_FLAG_UNCACHED & caching) != 0) + result |= TTM_PL_FLAG_UNCACHED; + + return result; +} + + static bool ttm_bo_mt_compatible(struct ttm_mem_type_manager *man, bool disallow_fixed, uint32_t mem_type, - uint32_t mask, uint32_t *res_mask) + uint32_t proposed_placement, + uint32_t *masked_placement) { uint32_t cur_flags = ttm_bo_type_flags(mem_type); if ((man->flags & TTM_MEMTYPE_FLAG_FIXED) && disallow_fixed) return false; - if ((cur_flags & mask & TTM_PL_MASK_MEM) == 0) + if ((cur_flags & proposed_placement & TTM_PL_MASK_MEM) == 0) return false; - if ((mask & man->available_caching) == 0) + if ((proposed_placement & man->available_caching) == 0) return false; - if (mask & man->default_caching) - cur_flags |= man->default_caching; - else if (mask & TTM_PL_FLAG_CACHED) - cur_flags |= TTM_PL_FLAG_CACHED; - else if (mask & TTM_PL_FLAG_WC) - cur_flags |= TTM_PL_FLAG_WC; - else - cur_flags |= TTM_PL_FLAG_UNCACHED; - *res_mask = cur_flags; + cur_flags |= (proposed_placement & man->available_caching); + + *masked_placement = cur_flags; return true; } @@ -723,6 +744,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo, if (!type_ok) continue; + cur_flags = ttm_bo_select_caching(man, bo->mem.placement, + cur_flags); + if (mem_type == TTM_PL_SYSTEM) break; @@ -779,6 +803,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo, proposed_placement, &cur_flags)) continue; + cur_flags = ttm_bo_select_caching(man, bo->mem.placement, + cur_flags); + ret = ttm_bo_mem_force_space(bdev, mem, mem_type, interruptible, no_wait); -- cgit v1.2.3 From 848577ee27f704231b1860ae987a1be78b88b06e Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 8 Jul 2009 16:15:30 -0400 Subject: drm/radeon/kms: fix quirk for MSI laptop The line mux for the connector in the bios tables is used for enumerating drm connectors. Since this laptop has a quirk where the same line much is listed for both VGA and LVDS, the connectors get combined. Setting the line mux on LVDS to an unused value prevents both encoders from being combined into the same connector. This should fix bko bug 13720. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_atombios.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_atombios.c b/drivers/gpu/drm/radeon/radeon_atombios.c index 1f5a1a490984..fcfe5c02d744 100644 --- a/drivers/gpu/drm/radeon/radeon_atombios.c +++ b/drivers/gpu/drm/radeon/radeon_atombios.c @@ -103,7 +103,8 @@ static inline struct radeon_i2c_bus_rec radeon_lookup_gpio(struct drm_device static bool radeon_atom_apply_quirks(struct drm_device *dev, uint32_t supported_device, int *connector_type, - struct radeon_i2c_bus_rec *i2c_bus) + struct radeon_i2c_bus_rec *i2c_bus, + uint8_t *line_mux) { /* Asus M2A-VM HDMI board lists the DVI port as HDMI */ @@ -127,8 +128,10 @@ static bool radeon_atom_apply_quirks(struct drm_device *dev, if ((dev->pdev->device == 0x5653) && (dev->pdev->subsystem_vendor == 0x1462) && (dev->pdev->subsystem_device == 0x0291)) { - if (*connector_type == DRM_MODE_CONNECTOR_LVDS) + if (*connector_type == DRM_MODE_CONNECTOR_LVDS) { i2c_bus->valid = false; + *line_mux = 53; + } } /* Funky macbooks */ @@ -526,7 +529,7 @@ bool radeon_get_atom_connector_info_from_supported_devices_table(struct if (!radeon_atom_apply_quirks (dev, (1 << i), &bios_connectors[i].connector_type, - &bios_connectors[i].ddc_bus)) + &bios_connectors[i].ddc_bus, &bios_connectors[i].line_mux)) continue; bios_connectors[i].valid = true; -- cgit v1.2.3 From 2007d633d639c896396e4c4b53b38068f3831307 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Wed, 8 Jul 2009 16:17:23 -0400 Subject: drm/radeon/kms: get lvds info for DIG LVTMA and UNIPHY encoders MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Noticed by Rafał Miłecki on dri-devel. On r6xx/r7xx hardware, laptop panels can be driven by KLDSCP_LVTMA or UNIPHY. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_encoders.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c index c8ef0d14ffab..ea15284e7580 100644 --- a/drivers/gpu/drm/radeon/radeon_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_encoders.c @@ -1700,8 +1700,14 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2: - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); - radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); + if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) { + radeon_encoder->rmx_type = RMX_FULL; + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS); + radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder); + } else { + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); + radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); + } drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs); break; } -- cgit v1.2.3 From e7168cab5bbac0a0e5413fd55ba0e92555bf860d Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Thu, 9 Jul 2009 16:01:42 +1000 Subject: drm/radeon/kms: fix vram vs aper size check. Fix this to be correct like the DDX code, looks like a typo on transfer to the kernel. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_device.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f97563db4e59..332911267ebe 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -552,7 +552,7 @@ int radeon_device_init(struct radeon_device *rdev, * for RN50/M6/M7 - Novell bug 204882 ? */ if (rdev->mc.vram_size < rdev->mc.aper_size) { - rdev->mc.aper_size = rdev->mc.vram_size; + rdev->mc.vram_size = rdev->mc.aper_size; } /* Add an MTRR for the VRAM */ rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, -- cgit v1.2.3 From 5176fdc4c5873e52f9cb6e166d80e843847e7eb4 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 30 Jun 2009 11:47:14 +1000 Subject: drm/radeon/kms: drop zero length CS indirect buffers. If userspace sends a zero length IB, it really shouldn't have bothered so EINVAL it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cs.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_cs.c b/drivers/gpu/drm/radeon/radeon_cs.c index b843f9bdfb14..a169067efc4e 100644 --- a/drivers/gpu/drm/radeon/radeon_cs.c +++ b/drivers/gpu/drm/radeon/radeon_cs.c @@ -127,17 +127,23 @@ int radeon_cs_parser_init(struct radeon_cs_parser *p, void *data) sizeof(struct drm_radeon_cs_chunk))) { return -EFAULT; } + p->chunks[i].length_dw = user_chunk.length_dw; + p->chunks[i].kdata = NULL; p->chunks[i].chunk_id = user_chunk.chunk_id; + if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_RELOCS) { p->chunk_relocs_idx = i; } if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_IB) { p->chunk_ib_idx = i; + /* zero length IB isn't useful */ + if (p->chunks[i].length_dw == 0) + return -EINVAL; } + p->chunks[i].length_dw = user_chunk.length_dw; cdata = (uint32_t *)(unsigned long)user_chunk.chunk_data; - p->chunks[i].kdata = NULL; size = p->chunks[i].length_dw * sizeof(uint32_t); p->chunks[i].kdata = kzalloc(size, GFP_KERNEL); if (p->chunks[i].kdata == NULL) { -- cgit v1.2.3 From 77bd36f014bc5a3f28507a4e86a81b2b3d2439c3 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 10 Jul 2009 09:33:00 +1000 Subject: drm/radeon/kms: don't swap PCIEGART PTEs in VRAM. On powerpc, since we aren't using any hw swappers, this will get flipped around by default in hw. tested on a G5 + rv515. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r300.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 656d9238bb06..6435d659cbd1 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -154,7 +154,10 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr) addr = (lower_32_bits(addr) >> 8) | ((upper_32_bits(addr) & 0xff) << 24) | 0xc; - writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4)); + /* on x86 we want this to be CPU endian, on powerpc + * on powerpc without HW swappers, it'll get swapped on way + * into VRAM - so no need for cpu_to_le32 on VRAM tables */ + writel(addr, ((void __iomem *)ptr) + (i * 4)); return 0; } -- cgit v1.2.3 From 61b576dbbe6a19d102c025ebc102a0749e2d3c80 Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Wed, 24 Jun 2009 00:12:55 +1000 Subject: drm/radeon: Endianness fixes for radeondrmfb. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit For now handle it via r/g/b offsets and disallow 16 bpp modes on big endian machines. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 53 +++++++++++++++++++++++++++++++++++--- 1 file changed, 50 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 9e8f191eb64a..260870a29d83 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -101,9 +101,10 @@ static int radeonfb_setcolreg(unsigned regno, break; case 24: case 32: - fb->pseudo_palette[regno] = ((red & 0xff00) << 8) | - (green & 0xff00) | - ((blue & 0xff00) >> 8); + fb->pseudo_palette[regno] = + (((red >> 8) & 0xff) << info->var.red.offset) | + (((green >> 8) & 0xff) << info->var.green.offset) | + (((blue >> 8) & 0xff) << info->var.blue.offset); break; } } @@ -154,6 +155,7 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var, var->transp.length = 0; var->transp.offset = 0; break; +#ifdef __LITTLE_ENDIAN case 15: var->red.offset = 10; var->green.offset = 5; @@ -194,6 +196,28 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var, var->transp.length = 8; var->transp.offset = 24; break; +#else + case 24: + var->red.offset = 8; + var->green.offset = 16; + var->blue.offset = 24; + var->red.length = 8; + var->green.length = 8; + var->blue.length = 8; + var->transp.length = 0; + var->transp.offset = 0; + break; + case 32: + var->red.offset = 8; + var->green.offset = 16; + var->blue.offset = 24; + var->red.length = 8; + var->green.length = 8; + var->blue.length = 8; + var->transp.length = 8; + var->transp.offset = 0; + break; +#endif default: return -EINVAL; } @@ -600,6 +624,7 @@ int radeonfb_create(struct radeon_device *rdev, info->var.transp.offset = 0; info->var.transp.length = 0; break; +#ifdef __LITTLE_ENDIAN case 15: info->var.red.offset = 10; info->var.green.offset = 5; @@ -639,7 +664,29 @@ int radeonfb_create(struct radeon_device *rdev, info->var.transp.offset = 24; info->var.transp.length = 8; break; +#else + case 24: + info->var.red.offset = 8; + info->var.green.offset = 16; + info->var.blue.offset = 24; + info->var.red.length = 8; + info->var.green.length = 8; + info->var.blue.length = 8; + info->var.transp.offset = 0; + info->var.transp.length = 0; + break; + case 32: + info->var.red.offset = 8; + info->var.green.offset = 16; + info->var.blue.offset = 24; + info->var.red.length = 8; + info->var.green.length = 8; + info->var.blue.length = 8; + info->var.transp.offset = 0; + info->var.transp.length = 8; + break; default: +#endif break; } -- cgit v1.2.3 From ad49f501867cba87e1e45e5ebae0b12435d68bf1 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 10 Jul 2009 22:36:26 +1000 Subject: drm/ttm/radeon: add dma32 support. This add support for using dma32 memory on gpus that really need it. Currently IGPs are left without DMA32 but we might need to change that unless we can fix rs690. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 1 + drivers/gpu/drm/radeon/radeon_device.c | 17 +++++++++++++++-- drivers/gpu/drm/radeon/radeon_ttm.c | 3 ++- drivers/gpu/drm/ttm/ttm_bo.c | 7 ++++++- drivers/gpu/drm/ttm/ttm_tt.c | 9 +++++++-- include/drm/ttm/ttm_bo_driver.h | 5 ++++- 6 files changed, 35 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index e7662ba9abfb..3060ce14071e 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -624,6 +624,7 @@ struct radeon_device { bool gpu_lockup; bool shutdown; bool suspend; + bool need_dma32; }; int radeon_device_init(struct radeon_device *rdev, diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 332911267ebe..27a5ac969953 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -450,6 +450,7 @@ int radeon_device_init(struct radeon_device *rdev, uint32_t flags) { int r, ret; + int dma_bits; DRM_INFO("radeon: Initializing kernel modesetting.\n"); rdev->shutdown = false; @@ -492,8 +493,20 @@ int radeon_device_init(struct radeon_device *rdev, return r; } - /* Report DMA addressing limitation */ - r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(32)); + /* set DMA mask + need_dma32 flags. + * PCIE - can handle 40-bits. + * IGP - can handle 40-bits (in theory) + * AGP - generally dma32 is safest + * PCI - only dma32 + */ + rdev->need_dma32 = false; + if (rdev->flags & RADEON_IS_AGP) + rdev->need_dma32 = true; + if (rdev->flags & RADEON_IS_PCI) + rdev->need_dma32 = true; + + dma_bits = rdev->need_dma32 ? 32 : 40; + r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(dma_bits)); if (r) { printk(KERN_WARNING "radeon: No suitable DMA available.\n"); } diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 1227a97f5169..4ca9aa9203d0 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -442,7 +442,8 @@ int radeon_ttm_init(struct radeon_device *rdev) /* No others user of address space so set it to 0 */ r = ttm_bo_device_init(&rdev->mman.bdev, rdev->mman.mem_global_ref.object, - &radeon_bo_driver, DRM_FILE_PAGE_OFFSET); + &radeon_bo_driver, DRM_FILE_PAGE_OFFSET, + rdev->need_dma32); if (r) { DRM_ERROR("failed initializing buffer object driver(%d).\n", r); return r; diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index a753598a5e35..e55e7972c897 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -224,6 +224,9 @@ static int ttm_bo_add_ttm(struct ttm_buffer_object *bo, bool zero_alloc) TTM_ASSERT_LOCKED(&bo->mutex); bo->ttm = NULL; + if (bdev->need_dma32) + page_flags |= TTM_PAGE_FLAG_DMA32; + switch (bo->type) { case ttm_bo_type_device: if (zero_alloc) @@ -1332,7 +1335,8 @@ EXPORT_SYMBOL(ttm_bo_device_release); int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_mem_global *mem_glob, - struct ttm_bo_driver *driver, uint64_t file_page_offset) + struct ttm_bo_driver *driver, uint64_t file_page_offset, + bool need_dma32) { int ret = -EINVAL; @@ -1369,6 +1373,7 @@ int ttm_bo_device_init(struct ttm_bo_device *bdev, INIT_LIST_HEAD(&bdev->ddestroy); INIT_LIST_HEAD(&bdev->swap_lru); bdev->dev_mapping = NULL; + bdev->need_dma32 = need_dma32; ttm_mem_init_shrink(&bdev->shrink, ttm_bo_swapout); ret = ttm_mem_register_shrink(mem_glob, &bdev->shrink); if (unlikely(ret != 0)) { diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 75dc8bd24592..81ab81f030a3 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -131,10 +131,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm) static struct page *ttm_tt_alloc_page(unsigned page_flags) { + gfp_t gfp_flags = GFP_HIGHUSER; + if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC) - return alloc_page(GFP_HIGHUSER | __GFP_ZERO); + gfp_flags |= __GFP_ZERO; + + if (page_flags & TTM_PAGE_FLAG_DMA32) + gfp_flags |= __GFP_DMA32; - return alloc_page(GFP_HIGHUSER); + return alloc_page(gfp_flags); } static void ttm_tt_free_user_pages(struct ttm_tt *ttm) diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index 62ed733c52a2..ea83dd23a4d7 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -121,6 +121,7 @@ struct ttm_backend { #define TTM_PAGE_FLAG_SWAPPED (1 << 4) #define TTM_PAGE_FLAG_PERSISTANT_SWAP (1 << 5) #define TTM_PAGE_FLAG_ZERO_ALLOC (1 << 6) +#define TTM_PAGE_FLAG_DMA32 (1 << 7) enum ttm_caching_state { tt_uncached, @@ -429,6 +430,8 @@ struct ttm_bo_device { */ struct delayed_work wq; + + bool need_dma32; }; /** @@ -648,7 +651,7 @@ extern int ttm_bo_device_release(struct ttm_bo_device *bdev); extern int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_mem_global *mem_glob, struct ttm_bo_driver *driver, - uint64_t file_page_offset); + uint64_t file_page_offset, bool need_dma32); /** * ttm_bo_reserve: -- cgit v1.2.3 From 2a0f8918fc34713ecaeb900ffb9afa61df4cb08e Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 11 Jul 2009 04:44:47 +1000 Subject: drm/radeon/kms: fix VRAM sizing like DDX does it. Doing this like the DDX seems like the most sure fire way to avoid having to reinvent it slowly and painfully. At the moment we keep getting things wrong with aper vs vram, so we know the DDX does it right. booted on PCI r100, PCIE rv370, IGP rs400. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 65 ++++++++++++++++++++++++++++++++-- drivers/gpu/drm/radeon/r300.c | 4 +-- drivers/gpu/drm/radeon/r520.c | 4 +-- drivers/gpu/drm/radeon/radeon.h | 2 ++ drivers/gpu/drm/radeon/radeon_device.c | 7 +--- drivers/gpu/drm/radeon/rs400.c | 14 +------- drivers/gpu/drm/radeon/rv515.c | 6 ++-- 7 files changed, 71 insertions(+), 31 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 154648a2c027..97c9229b9299 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1360,9 +1360,50 @@ static void r100_vram_get_type(struct radeon_device *rdev) } } -void r100_vram_info(struct radeon_device *rdev) +static u32 r100_get_accessible_vram(struct radeon_device *rdev) { - r100_vram_get_type(rdev); + u32 aper_size; + u8 byte; + + aper_size = RREG32(RADEON_CONFIG_APER_SIZE); + + /* Set HDP_APER_CNTL only on cards that are known not to be broken, + * that is has the 2nd generation multifunction PCI interface + */ + if (rdev->family == CHIP_RV280 || + rdev->family >= CHIP_RV350) { + WREG32_P(RADEON_HOST_PATH_CNTL, RADEON_HDP_APER_CNTL, + ~RADEON_HDP_APER_CNTL); + DRM_INFO("Generation 2 PCI interface, using max accessible memory\n"); + return aper_size * 2; + } + + /* Older cards have all sorts of funny issues to deal with. First + * check if it's a multifunction card by reading the PCI config + * header type... Limit those to one aperture size + */ + pci_read_config_byte(rdev->pdev, 0xe, &byte); + if (byte & 0x80) { + DRM_INFO("Generation 1 PCI interface in multifunction mode\n"); + DRM_INFO("Limiting VRAM to one aperture\n"); + return aper_size; + } + + /* Single function older card. We read HDP_APER_CNTL to see how the BIOS + * have set it up. We don't write this as it's broken on some ASICs but + * we expect the BIOS to have done the right thing (might be too optimistic...) + */ + if (RREG32(RADEON_HOST_PATH_CNTL) & RADEON_HDP_APER_CNTL) + return aper_size * 2; + return aper_size; +} + +void r100_vram_init_sizes(struct radeon_device *rdev) +{ + u64 config_aper_size; + u32 accessible; + + config_aper_size = RREG32(RADEON_CONFIG_APER_SIZE); if (rdev->flags & RADEON_IS_IGP) { uint32_t tom; @@ -1383,10 +1424,30 @@ void r100_vram_info(struct radeon_device *rdev) } /* let driver place VRAM */ rdev->mc.vram_location = 0xFFFFFFFFUL; + /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - + * Novell bug 204882 + along with lots of ubuntu ones */ + if (config_aper_size > rdev->mc.vram_size) + rdev->mc.vram_size = config_aper_size; } + /* work out accessible VRAM */ + accessible = r100_get_accessible_vram(rdev); + rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + + if (accessible > rdev->mc.aper_size) + accessible = rdev->mc.aper_size; + + if (rdev->mc.vram_size > rdev->mc.aper_size) + rdev->mc.vram_size = rdev->mc.aper_size; +} + +void r100_vram_info(struct radeon_device *rdev) +{ + r100_vram_get_type(rdev); + + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 6435d659cbd1..0e0e094da503 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -585,10 +585,8 @@ void r300_vram_info(struct radeon_device *rdev) } else { rdev->mc.vram_width = 64; } - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index 570a244bd88b..b6bd3758db6b 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -227,8 +227,6 @@ static void r520_vram_get_type(struct radeon_device *rdev) void r520_vram_info(struct radeon_device *rdev) { r520_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 3060ce14071e..248e3341a984 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -541,6 +541,8 @@ union radeon_asic_config { struct r300_asic r300; }; +/* r100 */ +void r100_vram_init_sizes(struct radeon_device *rdev); /* * IOCTL. diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 27a5ac969953..cdef6eb01baf 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -561,12 +561,7 @@ int radeon_device_init(struct radeon_device *rdev, } /* Get vram informations */ radeon_vram_info(rdev); - /* Device is severly broken if aper size > vram size. - * for RN50/M6/M7 - Novell bug 204882 ? - */ - if (rdev->mc.vram_size < rdev->mc.aper_size) { - rdev->mc.vram_size = rdev->mc.aper_size; - } + /* Add an MTRR for the VRAM */ rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, MTRR_TYPE_WRCOMB, 1); diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index a18d053065c0..daf24e85cba3 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -292,24 +292,12 @@ void rs400_gpu_init(struct radeon_device *rdev) */ void rs400_vram_info(struct radeon_device *rdev) { - uint32_t tom; - rs400_gart_adjust_size(rdev); /* DDR for all card after R300 & IGP */ rdev->mc.vram_is_ddr = true; rdev->mc.vram_width = 128; - /* read NB_TOM to get the amount of ram stolen for the GPU */ - tom = RREG32(RADEON_NB_TOM); - rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - - /* RS480 IGPs don't seem to translate to main RAM, they - * just reserve and scan out of it. So setting VRAM location - * to say 0, will actually trash the OS. */ - rdev->mc.vram_location = (tom & 0xffff) << 16; - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + r100_vram_init_sizes(rdev); } diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index d1384d3991ad..677929ed8ed3 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -395,10 +395,8 @@ static void rv515_vram_get_type(struct radeon_device *rdev) void rv515_vram_info(struct radeon_device *rdev) { rv515_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); - - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + + r100_vram_init_sizes(rdev); } -- cgit v1.2.3 From b995e4330de0d8b1b8b9e49ce10cc6dc78e2cbba Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 14 Jul 2009 02:02:32 +1000 Subject: drm/radeon/kms: block RN50 from using 3D engine. RN50/ES1000 is a cut-down rv100 chip used in the server market. The 3D engine on these is either not there or unverified so refuse any attempt to configure registers on it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 5 +++++ drivers/gpu/drm/radeon/radeon.h | 2 ++ 2 files changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 97c9229b9299..0d05909f03f6 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -973,6 +973,11 @@ static int r100_packet0_check(struct radeon_cs_parser *p, case R300_TX_OFFSET_0+52: case R300_TX_OFFSET_0+56: case R300_TX_OFFSET_0+60: + /* rn50 has no 3D engine so fail on any 3d setup */ + if (ASIC_IS_RN50(p->rdev)) { + DRM_ERROR("attempt to use RN50 3D engine failed\n"); + return -EINVAL; + } r = r100_cs_packet_next_reloc(p, &reloc); if (r) { DRM_ERROR("No reloc for ib[%d]=0x%04X\n", diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 248e3341a984..7f007185e7f7 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -673,6 +673,8 @@ void r100_pll_errata_after_index(struct radeon_device *rdev); /* * ASICs helpers. */ +#define ASIC_IS_RN50(rdev) ((rdev->pdev->device == 0x515e) || \ + (rdev->pdev->device == 0x5969)) #define ASIC_IS_RV100(rdev) ((rdev->family == CHIP_RV100) || \ (rdev->family == CHIP_RV200) || \ (rdev->family == CHIP_RS100) || \ -- cgit v1.2.3 From d0e275a90a81b37409a0cfbca77581e3d235f5cf Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 11:08:18 -0400 Subject: drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq This is needed when using fractional feedback dividers on some IGP chips. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_display.c | 6 +++++- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c index 3efcf1a526be..bc312f3d9a0a 100644 --- a/drivers/gpu/drm/radeon/radeon_display.c +++ b/drivers/gpu/drm/radeon/radeon_display.c @@ -491,7 +491,11 @@ void radeon_compute_pll(struct radeon_pll *pll, tmp += (uint64_t)pll->reference_freq * 1000 * frac_feedback_div; current_freq = radeon_div(tmp, ref_div * post_div); - error = abs(current_freq - freq); + if (flags & RADEON_PLL_PREFER_CLOSEST_LOWER) { + error = freq - current_freq; + error = error < 0 ? 0xffffffff : error; + } else + error = abs(current_freq - freq); vco_diff = abs(vco - best_vco); if ((best_vco == 0 && error < best_error) || diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 86f766e868e7..38c1dd082441 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -124,6 +124,7 @@ struct radeon_tmds_pll { #define RADEON_PLL_PREFER_LOW_POST_DIV (1 << 8) #define RADEON_PLL_PREFER_HIGH_POST_DIV (1 << 9) #define RADEON_PLL_USE_FRAC_FB_DIV (1 << 10) +#define RADEON_PLL_PREFER_CLOSEST_LOWER (1 << 11) struct radeon_pll { uint16_t reference_freq; -- cgit v1.2.3 From eb1300bcd70b3bffbefb6ae0eab13a571255ee93 Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 11:09:56 -0400 Subject: drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740 Allows us to hit dot clocks much closer, especially on chips with non-27 Mhz reference clocks like most IGP chips. This fixes most flickering and blanking problems with non-exact dot clocks on these chips. Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index c0080cc9bf8d..e64a199b5ee1 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -203,6 +203,12 @@ void atombios_crtc_set_pll(struct drm_crtc *crtc, struct drm_display_mode *mode) if (ASIC_IS_AVIVO(rdev)) { uint32_t ss_cntl; + if ((rdev->family == CHIP_RS600) || + (rdev->family == CHIP_RS690) || + (rdev->family == CHIP_RS740)) + pll_flags |= (RADEON_PLL_USE_FRAC_FB_DIV | + RADEON_PLL_PREFER_CLOSEST_LOWER); + if (ASIC_IS_DCE32(rdev) && mode->clock > 200000) /* range limits??? */ pll_flags |= RADEON_PLL_PREFER_HIGH_FB_DIV; else -- cgit v1.2.3 From c836e862803b2aa2bd9a354e151316d2b42c44ec Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Mon, 13 Jul 2009 13:51:03 -0400 Subject: drm/radeon/kms: fix hotspot handling on pre-avivo chips Need to adjust CUR_OFFSET for yorigin Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_cursor.c | 9 +++++++-- drivers/gpu/drm/radeon/radeon_mode.h | 1 + 2 files changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c index 5f8ce370c4f8..b13c79e38bc0 100644 --- a/drivers/gpu/drm/radeon/radeon_cursor.c +++ b/drivers/gpu/drm/radeon/radeon_cursor.c @@ -111,9 +111,11 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj, if (ASIC_IS_AVIVO(rdev)) WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr); - else + else { + radeon_crtc->legacy_cursor_offset = gpu_addr - radeon_crtc->legacy_display_base_addr; /* offset is from DISP(2)_BASE_ADDRESS */ - WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr)); + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, radeon_crtc->legacy_cursor_offset); + } } int radeon_crtc_cursor_set(struct drm_crtc *crtc, @@ -245,6 +247,9 @@ int radeon_crtc_cursor_move(struct drm_crtc *crtc, (RADEON_CUR_LOCK | ((xorigin ? 0 : x) << 16) | (yorigin ? 0 : y))); + /* offset is from DISP(2)_BASE_ADDRESS */ + WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (radeon_crtc->legacy_cursor_offset + + (yorigin * 256))); } radeon_lock_cursor(crtc, false); diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index 38c1dd082441..ba89b59f6e50 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -187,6 +187,7 @@ struct radeon_crtc { int cursor_width; int cursor_height; uint32_t legacy_display_base_addr; + uint32_t legacy_cursor_offset; }; #define RADEON_USE_RMX 1 -- cgit v1.2.3 From c8cc452501572d4a81331179b00a9bdd5d2bfada Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 10 Jul 2009 16:59:36 +0300 Subject: UBI: gluebi: initialize ubi_num field Do not forget to initialize 'gluebi->ubi_num' because otherwise it will stay 0 even for ubi1 device, and gluebi will open wrong UBI device when 'gluebi_get_device()' is called. Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/gluebi.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/mtd/ubi/gluebi.c b/drivers/mtd/ubi/gluebi.c index 95aaac03f938..b5e478fa2661 100644 --- a/drivers/mtd/ubi/gluebi.c +++ b/drivers/mtd/ubi/gluebi.c @@ -332,6 +332,7 @@ static int gluebi_create(struct ubi_device_info *di, } gluebi->vol_id = vi->vol_id; + gluebi->ubi_num = vi->ubi_num; mtd->type = MTD_UBIVOLUME; if (!di->ro_mode) mtd->flags = MTD_WRITEABLE; -- cgit v1.2.3 From 3dc948da783e713cd3dc8bbd8f293f8795af8f06 Mon Sep 17 00:00:00 2001 From: Holger Brunck Date: Mon, 13 Jul 2009 16:47:57 +0200 Subject: UBI: fix bug in image sequence number handling This patch fixes a bug in the image seq. number handling in the scanning level. The assignment of the image_seq was incorrect. Signed-off-by: Holger Brunck Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/scan.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c index f60895ee0aeb..a423131b6171 100644 --- a/drivers/mtd/ubi/scan.c +++ b/drivers/mtd/ubi/scan.c @@ -781,7 +781,7 @@ static int process_eb(struct ubi_device *ubi, struct ubi_scan_info *si, return -EINVAL; } - image_seq = be32_to_cpu(ech->ec); + image_seq = be32_to_cpu(ech->image_seq); if (!si->image_seq_set) { ubi->image_seq = image_seq; si->image_seq_set = 1; -- cgit v1.2.3 From 4a21b8cb3550f19f838f7c48345fbbf6a0e8536b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 16 Jul 2009 09:14:23 -0700 Subject: Revert "ppp: Fix throttling bugs" This reverts commit a6540f731d506d9e82444cf0020e716613d4c46c, as requested by Alan: "... as it was wrong, the pty code is now fixed and the fact this isn't reverted is breaking pptp setups." Requested-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/net/ppp_async.c | 1 + drivers/net/ppp_synctty.c | 1 + 2 files changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ppp_async.c b/drivers/net/ppp_async.c index 17c116bb332c..6de8399d6dd9 100644 --- a/drivers/net/ppp_async.c +++ b/drivers/net/ppp_async.c @@ -356,6 +356,7 @@ ppp_asynctty_receive(struct tty_struct *tty, const unsigned char *buf, if (!skb_queue_empty(&ap->rqueue)) tasklet_schedule(&ap->tsk); ap_put(ap); + tty_unthrottle(tty); } static void diff --git a/drivers/net/ppp_synctty.c b/drivers/net/ppp_synctty.c index aa3d39f38e22..d2fa2db13586 100644 --- a/drivers/net/ppp_synctty.c +++ b/drivers/net/ppp_synctty.c @@ -397,6 +397,7 @@ ppp_sync_receive(struct tty_struct *tty, const unsigned char *buf, if (!skb_queue_empty(&ap->rqueue)) tasklet_schedule(&ap->tsk); sp_put(ap); + tty_unthrottle(tty); } static void -- cgit v1.2.3 From c8d50041734534e0a4b0ea13df36ed5857fccd56 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Thu, 16 Jul 2009 16:05:08 +0100 Subject: tty: fix close/hangup race We can get a situation where a hangup occurs during or after a close. In that case the ldisc gets disposed of by the close and the hangup then explodes. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/tty_ldisc.c | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index 0ef0dc97ba20..acd76b767d4c 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -790,17 +790,20 @@ void tty_ldisc_hangup(struct tty_struct *tty) * N_TTY. */ if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) { - /* Avoid racing set_ldisc */ + /* Avoid racing set_ldisc or tty_ldisc_release */ mutex_lock(&tty->ldisc_mutex); - /* Switch back to N_TTY */ - tty_ldisc_halt(tty); - tty_ldisc_wait_idle(tty); - tty_ldisc_reinit(tty); - /* At this point we have a closed ldisc and we want to - reopen it. We could defer this to the next open but - it means auditing a lot of other paths so this is a FIXME */ - WARN_ON(tty_ldisc_open(tty, tty->ldisc)); - tty_ldisc_enable(tty); + if (tty->ldisc) { /* Not yet closed */ + /* Switch back to N_TTY */ + tty_ldisc_halt(tty); + tty_ldisc_wait_idle(tty); + tty_ldisc_reinit(tty); + /* At this point we have a closed ldisc and we want to + reopen it. We could defer this to the next open but + it means auditing a lot of other paths so this is + a FIXME */ + WARN_ON(tty_ldisc_open(tty, tty->ldisc)); + tty_ldisc_enable(tty); + } mutex_unlock(&tty->ldisc_mutex); tty_reset_termios(tty); } @@ -865,6 +868,7 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty) tty_ldisc_wait_idle(tty); + mutex_lock(&tty->ldisc_mutex); /* * Now kill off the ldisc */ @@ -875,6 +879,7 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty) /* Ensure the next open requests the N_TTY ldisc */ tty_set_termios_ldisc(tty, N_TTY); + mutex_unlock(&tty->ldisc_mutex); /* This will need doing differently if we need to lock */ if (o_tty) -- cgit v1.2.3 From 8f4256b22c554f713ffdd395c1f2bfd53746cfc9 Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Thu, 16 Jul 2009 16:05:43 +0100 Subject: serial: don't add msm_serial's probe function to the driver struct MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit msm_serial_driver is registered using platform_driver_probe which takes care for the probe function itself. So don't pass it in the driver struct, too. Signed-off-by: Uwe Kleine-König Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/serial/msm_serial.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/serial/msm_serial.c b/drivers/serial/msm_serial.c index 698048f64f5e..f7c24baa1416 100644 --- a/drivers/serial/msm_serial.c +++ b/drivers/serial/msm_serial.c @@ -730,7 +730,6 @@ static int __devexit msm_serial_remove(struct platform_device *pdev) } static struct platform_driver msm_platform_driver = { - .probe = msm_serial_probe, .remove = msm_serial_remove, .driver = { .name = "msm_serial", -- cgit v1.2.3 From ff5392d77bbb0746d1a034e955231f03ffc30b61 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Thu, 16 Jul 2009 16:05:53 +0100 Subject: drivers/serial/bfin_sport_uart.c: remove wrong and unneeded memset dcb314@hotmail.com notes that this memset has its args reversed. It's unneeded anyway, so remove it. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13587 Signed-off-by: Andrew Morton Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/serial/bfin_sport_uart.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/serial/bfin_sport_uart.c b/drivers/serial/bfin_sport_uart.c index 34b4ae0fe760..c108b1a0ce98 100644 --- a/drivers/serial/bfin_sport_uart.c +++ b/drivers/serial/bfin_sport_uart.c @@ -236,7 +236,6 @@ static int sport_startup(struct uart_port *port) int retval; pr_debug("%s enter\n", __func__); - memset(buffer, 20, '\0'); snprintf(buffer, 20, "%s rx", up->name); retval = request_irq(up->rx_irq, sport_uart_rx_irq, IRQF_SAMPLE_RANDOM, buffer, up); if (retval) { -- cgit v1.2.3 From 5c9228f0cfb09a098a8a380116b42ae099e967b6 Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Thu, 16 Jul 2009 16:06:09 +0100 Subject: vt: drop bootmem/slab memory distinction Bootmem is not used for the vt screen buffer anymore as slab is now available at the time the console is initialized. Get rid of the now superfluous distinction between slab and bootmem, it's always slab. This also fixes a kmalloc leak which Catalin described thusly: Commit a5f4f52e ("vt: use kzalloc() instead of the bootmem allocator") replaced the alloc_bootmem() with kzalloc() but didn't set vc_kmalloced to 1 and the memory block is later leaked. The corresponding kmemleak trace: unreferenced object 0xdf828000 (size 8192): comm "swapper", pid 0, jiffies 4294937296 backtrace: [] __save_stack_trace+0x17/0x1c [] log_early+0x55/0x84 [] kmemleak_alloc+0x33/0x3c [] __kmalloc+0xd7/0xe4 [] con_init+0xbf/0x1b8 [] console_init+0x11/0x20 [] start_kernel+0x137/0x1e4 Signed-off-by: Johannes Weiner Reviewed-by: Pekka Enberg Tested-by: Catalin Marinas Signed-off-by: Andrew Morton Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/vt.c | 12 +++--------- include/linux/console_struct.h | 1 - 2 files changed, 3 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/char/vt.c b/drivers/char/vt.c index 7947bd1b4cf7..404f4c1ee431 100644 --- a/drivers/char/vt.c +++ b/drivers/char/vt.c @@ -770,14 +770,12 @@ int vc_allocate(unsigned int currcons) /* return 0 on success */ visual_init(vc, currcons, 1); if (!*vc->vc_uni_pagedir_loc) con_set_default_unimap(vc); - if (!vc->vc_kmalloced) - vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL); + vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL); if (!vc->vc_screenbuf) { kfree(vc); vc_cons[currcons].d = NULL; return -ENOMEM; } - vc->vc_kmalloced = 1; vc_init(vc, vc->vc_rows, vc->vc_cols, 1); vcs_make_sysfs(currcons); atomic_notifier_call_chain(&vt_notifier_list, VT_ALLOCATE, ¶m); @@ -913,10 +911,8 @@ static int vc_do_resize(struct tty_struct *tty, struct vc_data *vc, if (new_scr_end > new_origin) scr_memsetw((void *)new_origin, vc->vc_video_erase_char, new_scr_end - new_origin); - if (vc->vc_kmalloced) - kfree(vc->vc_screenbuf); + kfree(vc->vc_screenbuf); vc->vc_screenbuf = newscreen; - vc->vc_kmalloced = 1; vc->vc_screenbuf_size = new_screen_size; set_origin(vc); @@ -995,8 +991,7 @@ void vc_deallocate(unsigned int currcons) vc->vc_sw->con_deinit(vc); put_pid(vc->vt_pid); module_put(vc->vc_sw->owner); - if (vc->vc_kmalloced) - kfree(vc->vc_screenbuf); + kfree(vc->vc_screenbuf); if (currcons >= MIN_NR_CONSOLES) kfree(vc); vc_cons[currcons].d = NULL; @@ -2881,7 +2876,6 @@ static int __init con_init(void) INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK); visual_init(vc, currcons, 1); vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_NOWAIT); - vc->vc_kmalloced = 0; vc_init(vc, vc->vc_rows, vc->vc_cols, currcons || !vc->vc_sw->con_save_screen); } diff --git a/include/linux/console_struct.h b/include/linux/console_struct.h index d71f7c0f931b..38fe59dc89ae 100644 --- a/include/linux/console_struct.h +++ b/include/linux/console_struct.h @@ -89,7 +89,6 @@ struct vc_data { unsigned int vc_need_wrap : 1; unsigned int vc_can_do_color : 1; unsigned int vc_report_mouse : 2; - unsigned int vc_kmalloced : 1; unsigned char vc_utf : 1; /* Unicode UTF-8 encoding */ unsigned char vc_utf_count; int vc_utf_char; -- cgit v1.2.3 From 9237a81a1468d0aca1cc4e244bba2362d6f81b35 Mon Sep 17 00:00:00 2001 From: Jiri Slaby Date: Thu, 16 Jul 2009 16:06:18 +0100 Subject: tty: nozomi, fix tty refcounting bug Don't forget to drop a tty refererence on fail paths in receive_data(). Signed-off-by: Jiri Slaby Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/nozomi.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/char/nozomi.c b/drivers/char/nozomi.c index 574f1c79b6e6..280b41c507a7 100644 --- a/drivers/char/nozomi.c +++ b/drivers/char/nozomi.c @@ -828,7 +828,7 @@ static int receive_data(enum port_type index, struct nozomi *dc) struct port *port = &dc->port[index]; void __iomem *addr = port->dl_addr[port->toggle_dl]; struct tty_struct *tty = tty_port_tty_get(&port->port); - int i; + int i, ret; if (unlikely(!tty)) { DBG1("tty not open for port: %d?", index); @@ -844,12 +844,14 @@ static int receive_data(enum port_type index, struct nozomi *dc) /* disable interrupt in downlink... */ disable_transmit_dl(index, dc); - return 0; + ret = 0; + goto put; } if (unlikely(size == 0)) { dev_err(&dc->pdev->dev, "size == 0?\n"); - return 1; + ret = 1; + goto put; } tty_buffer_request_room(tty, size); @@ -871,8 +873,10 @@ static int receive_data(enum port_type index, struct nozomi *dc) } set_bit(index, &dc->flip); + ret = 1; +put: tty_kref_put(tty); - return 1; + return ret; } /* Debug for interrupts */ -- cgit v1.2.3 From 807708844979ba8c6d5717345a8608454992696d Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Thu, 16 Jul 2009 16:07:03 +0100 Subject: n_tty: Fix echo race If a tty in N_TTY mode with echo enabled manages to get itself into a state where - echo characters are pending - FASYNC is enabled - tty_write_wakeup is called from either - a device write path (pty) - an IRQ (serial) then it either deadlocks or explodes taking a mutex in the IRQ path. On the serial side it is almost impossible to reproduce because you have to go from a full serial port to a near empty one with echo characters pending. The pty case happens to have become possible to trigger using emacs and ptys, the pty changes having created a scenario which shows up this bug. The code path is n_tty:process_echoes() (takes mutex) tty_io:tty_put_char() pty:pty_write (or serial paths) tty_wakeup (from pty_write or serial IRQ) n_tty_write_wakeup() process_echoes() *KABOOM* Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/n_tty.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'drivers') diff --git a/drivers/char/n_tty.c b/drivers/char/n_tty.c index 94a5d5020abc..ff47907ff1bf 100644 --- a/drivers/char/n_tty.c +++ b/drivers/char/n_tty.c @@ -1331,9 +1331,6 @@ handle_newline: static void n_tty_write_wakeup(struct tty_struct *tty) { - /* Write out any echoed characters that are still pending */ - process_echoes(tty); - if (tty->fasync && test_and_clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags)) kill_fasync(&tty->fasync, SIGIO, POLL_OUT); } -- cgit v1.2.3 From 5381837f125cc62ad703fbcdfcd7566fc81fd404 Mon Sep 17 00:00:00 2001 From: Tom Peng Date: Wed, 1 Jul 2009 20:37:26 +0800 Subject: [SCSI] libsas: reuse the original port when hotplugging phys in wide ports There's a hotplug problem in the way libsas allocates ports: it loops over the available ports first trying to add to an existing for a wide port and otherwise allocating the next free port. This scheme only works if the port array is packed from zero, which fails if a port gets hot unplugged and the array becomes sparse. In that case, a new port is formed even if there's a wide port it should be part of. Fix this by creating two loops over all the ports: the first to see if the phy should be part of a wide port and the second to form a new port in an empty port slot. Signed-off-by: Tom Peng Signed-off-by: Jack Wang Signed-off-by: Lindar Liu Cc: Stable Tree Signed-off-by: James Bottomley --- drivers/scsi/libsas/sas_port.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/libsas/sas_port.c b/drivers/scsi/libsas/sas_port.c index e6ac59c023f1..fe8b74c706d2 100644 --- a/drivers/scsi/libsas/sas_port.c +++ b/drivers/scsi/libsas/sas_port.c @@ -56,7 +56,7 @@ static void sas_form_port(struct asd_sas_phy *phy) } } - /* find a port */ + /* see if the phy should be part of a wide port */ spin_lock_irqsave(&sas_ha->phy_port_lock, flags); for (i = 0; i < sas_ha->num_phys; i++) { port = sas_ha->sas_port[i]; @@ -69,12 +69,23 @@ static void sas_form_port(struct asd_sas_phy *phy) SAS_DPRINTK("phy%d matched wide port%d\n", phy->id, port->id); break; - } else if (*(u64 *) port->sas_addr == 0 && port->num_phys==0) { - memcpy(port->sas_addr, phy->sas_addr, SAS_ADDR_SIZE); - break; } spin_unlock(&port->phy_list_lock); } + /* The phy does not match any existing port, create a new one */ + if (i == sas_ha->num_phys) { + for (i = 0; i < sas_ha->num_phys; i++) { + port = sas_ha->sas_port[i]; + spin_lock(&port->phy_list_lock); + if (*(u64 *)port->sas_addr == 0 + && port->num_phys == 0) { + memcpy(port->sas_addr, phy->sas_addr, + SAS_ADDR_SIZE); + break; + } + spin_unlock(&port->phy_list_lock); + } + } if (i >= sas_ha->num_phys) { printk(KERN_NOTICE "%s: couldn't find a free port, bug?\n", -- cgit v1.2.3 From 390c4dd448b1a5f04ea497c20f5ff664f8eeed01 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Thu, 16 Jul 2009 13:01:01 -0700 Subject: drm/i915: handle FIFO oversubsription correctly If you're pushing a plane hard (i.e. you need most or all of the FIFO entries just to cover your frame refresh latency), the watermark level may end up being negative. So fix up the signed vs. unsigned math in the calculation function to handle this correctly, giving all available FIFO entries to such a configuration. Reported-by: Eric Anholt Tested-by: Eric Anholt Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 3fa0d63c83b9..890f7108e723 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1674,7 +1674,7 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, int pixel_size, unsigned long latency_ns) { - unsigned long entries_required, wm_size; + long entries_required, wm_size; entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000; entries_required /= wm->cacheline_size; @@ -1685,9 +1685,10 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz, DRM_DEBUG("FIFO watermark level: %d\n", wm_size); - if (wm_size > wm->max_wm) + /* Don't promote wm_size to unsigned... */ + if (wm_size > (long)wm->max_wm) wm_size = wm->max_wm; - if (wm_size == 0) + if (wm_size <= 0) wm_size = wm->default_wm; return wm_size; } -- cgit v1.2.3 From 2a2430f4542467502d39660bfd66b0004fd8d6a9 Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Thu, 16 Jul 2009 13:01:02 -0700 Subject: drm/i915: correct self-refresh calculation in "everything off" case If no planes are enabled, the self-refresh calculation may end up doing a divide by zero. This patch should prevent that by making sure at least one of the CRTCs had a valid hdisplay value. Reported-by: Eric Anholt Tested-by: Eric Anholt Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 890f7108e723..a58bfadabd6f 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1906,7 +1906,7 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, cwm = 2; /* Calc sr entries for one plane configs */ - if (!planea_clock || !planeb_clock) { + if (sr_hdisplay && (!planea_clock || !planeb_clock)) { /* self-refresh has much higher latency */ const static int sr_latency_ns = 6000; @@ -1921,6 +1921,8 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, srwm = total_size - sr_entries; if (srwm < 0) srwm = 1; + if (IS_I9XX(dev)) + I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n", @@ -1935,8 +1937,6 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock, I915_WRITE(FW_BLC, fwater_lo); I915_WRITE(FW_BLC2, fwater_hi); - if (IS_I9XX(dev)) - I915_WRITE(FW_BLC_SELF, (srwm & 0x3f)); } static void i830_update_wm(struct drm_device *dev, int planea_clock, -- cgit v1.2.3 From c5ad4f592e27d782faea0a787d9181f192a69ef0 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 12 Jul 2009 11:40:34 +0000 Subject: atl1c: add missing parentheses Parentheses are required or the comparison occurs before the bitand. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/atl1c/atl1c.h b/drivers/net/atl1c/atl1c.h index e1658ef3fcdf..2a1120ad2e74 100644 --- a/drivers/net/atl1c/atl1c.h +++ b/drivers/net/atl1c/atl1c.h @@ -188,14 +188,14 @@ struct atl1c_tpd_ext_desc { #define RRS_HDS_TYPE_DATA 2 #define RRS_IS_NO_HDS_TYPE(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == 0) + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == 0) #define RRS_IS_HDS_HEAD(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == \ + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == \ RRS_HDS_TYPE_HEAD) #define RRS_IS_HDS_DATA(flag) \ - (((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK == \ + ((((flag) >> (RRS_HDS_TYPE_SHIFT)) & RRS_HDS_TYPE_MASK) == \ RRS_HDS_TYPE_DATA) /* rrs word 3 bit 0:31 */ @@ -245,7 +245,7 @@ struct atl1c_tpd_ext_desc { #define RRS_PACKET_TYPE_802_3 1 #define RRS_PACKET_TYPE_ETH 0 #define RRS_PACKET_IS_ETH(word) \ - (((word) >> RRS_PACKET_TYPE_SHIFT) & RRS_PACKET_TYPE_MASK == \ + ((((word) >> RRS_PACKET_TYPE_SHIFT) & RRS_PACKET_TYPE_MASK) == \ RRS_PACKET_TYPE_ETH) #define RRS_RXD_IS_VALID(word) \ ((((word) >> RRS_RXD_UPDATED_SHIFT) & RRS_RXD_UPDATED_MASK) == 1) -- cgit v1.2.3 From 37b76c697f4ac082e9923dfa8e8aecc8bc54a8e1 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 12 Jul 2009 12:57:38 +0000 Subject: atl1c: misplaced parenthesis Fix misplaced parenthesis Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/atl1c/atl1c_main.c b/drivers/net/atl1c/atl1c_main.c index cd547a205fb9..a383122679de 100644 --- a/drivers/net/atl1c/atl1c_main.c +++ b/drivers/net/atl1c/atl1c_main.c @@ -1689,7 +1689,7 @@ static void atl1c_clean_rx_irq(struct atl1c_adapter *adapter, u8 que, if (likely(RRS_RXD_IS_VALID(rrs->word3))) { rfd_num = (rrs->word0 >> RRS_RX_RFD_CNT_SHIFT) & RRS_RX_RFD_CNT_MASK; - if (unlikely(rfd_num) != 1) + if (unlikely(rfd_num != 1)) /* TODO support mul rfd*/ if (netif_msg_rx_err(adapter)) dev_warn(&pdev->dev, -- cgit v1.2.3 From e36b9d16c6a6d0f59803b3ef04ff3c22c3844c10 Mon Sep 17 00:00:00 2001 From: Moni Shoua Date: Wed, 15 Jul 2009 04:56:31 +0000 Subject: bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua Signed-off-by: Jay Vosburgh Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index d927f71af8a3..aa1be1feceed 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1459,8 +1459,16 @@ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev) * ether type (eg ARPHRD_ETHER and ARPHRD_INFINIBAND) share the same bond */ if (bond->slave_cnt == 0) { - if (slave_dev->type != ARPHRD_ETHER) - bond_setup_by_slave(bond_dev, slave_dev); + if (bond_dev->type != slave_dev->type) { + dev_close(bond_dev); + pr_debug("%s: change device type from %d to %d\n", + bond_dev->name, bond_dev->type, slave_dev->type); + if (slave_dev->type != ARPHRD_ETHER) + bond_setup_by_slave(bond_dev, slave_dev); + else + ether_setup(bond_dev); + dev_open(bond_dev); + } } else if (bond_dev->type != slave_dev->type) { pr_err(DRV_NAME ": %s ether type (%d) is different " "from other slaves (%d), can not enslave it.\n", -- cgit v1.2.3 From 303d67c288319768b19ed8dbed429fef7eb7c275 Mon Sep 17 00:00:00 2001 From: Krzysztof Halasa Date: Tue, 14 Jul 2009 11:01:54 +0000 Subject: E100: work around the driver using streaming DMA mapping for RX descriptors. E100 places it's RX packet descriptors inside skb->data and uses them with bidirectional streaming DMA mapping. Unfortunately it fails to transfer skb->data ownership to the device after it reads the descriptor's status, breaking on non-coherent (e.g., ARM) platforms. This have to be converted to use coherent memory for the descriptors. Signed-off-by: Krzysztof Halasa Acked-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e100.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/e100.c b/drivers/net/e100.c index efa680f4b8dd..41b648a67fec 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -1897,6 +1897,9 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx, if (ioread8(&nic->csr->scb.status) & rus_no_res) nic->ru_running = RU_SUSPENDED; + pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr, + sizeof(struct rfd), + PCI_DMA_BIDIRECTIONAL); return -ENODATA; } -- cgit v1.2.3 From 3d1454dd93e84ad1394b6b1646f13795e9f6928e Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Thu, 16 Jul 2009 13:20:57 +0000 Subject: sky2: revert shutdown changes The commit changes to shutdown path broke startup on some systems. revert commit c0bad0f2e4366d5bbfe0c4a7a80bca8f4b05272b Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/sky2.c | 9 +-------- 1 file changed, 1 insertion(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index daf961ab68bc..ba768dfa59e0 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1151,14 +1151,7 @@ stopped: /* reset the Rx prefetch unit */ sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); - - /* Reset the RAM Buffer receive queue */ - sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_RST_SET); - - /* Reset Rx MAC FIFO */ - sky2_write8(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), GMF_RST_SET); - - sky2_read8(hw, B0_CTST); + mmiowb(); } /* Clean out receive buffer area, assumes receiver hardware stopped */ -- cgit v1.2.3 From 86e713a06ab3e5b15a3189485ce33aa21b9e52ca Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 16 Jul 2009 13:43:10 +0000 Subject: ixgbe: clear mac address data block in DCB mode This change clears the address data block memory space, which is needed for the 82598 which does not have a SAN MAC. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_dcb_nl.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index 7c5978ad929a..5b8dab22c6da 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -175,6 +175,8 @@ static void ixgbe_dcbnl_get_perm_hw_addr(struct net_device *netdev, struct ixgbe_adapter *adapter = netdev_priv(netdev); int i, j; + memset(perm_addr, 0xff, MAX_ADDR_LEN); + for (i = 0; i < netdev->addr_len; i++) perm_addr[i] = adapter->hw.mac.perm_addr[i]; -- cgit v1.2.3 From 869f1c54e9aecde1dfd4349832ce9415a596be8e Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 16 Jul 2009 13:43:31 +0000 Subject: ixgbe: Remove DPRINTK messages in DCB mode Remove debug DPRINTK in DCB mode netlink interface. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_dcb_nl.c | 4 ---- 1 file changed, 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index 5b8dab22c6da..da2c8514b8d0 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -106,8 +106,6 @@ static u8 ixgbe_dcbnl_get_state(struct net_device *netdev) { struct ixgbe_adapter *adapter = netdev_priv(netdev); - DPRINTK(DRV, INFO, "Get DCB Admin Mode.\n"); - return !!(adapter->flags & IXGBE_FLAG_DCB_ENABLED); } @@ -116,8 +114,6 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) u8 err = 0; struct ixgbe_adapter *adapter = netdev_priv(netdev); - DPRINTK(DRV, INFO, "Set DCB Admin Mode.\n"); - if (state > 0) { /* Turn on DCB */ if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) -- cgit v1.2.3 From 7fefe6a88494b00b151b5ca7bb84daaa781bbca7 Mon Sep 17 00:00:00 2001 From: Vincent CUISSARD Date: Thu, 16 Jul 2009 06:08:58 +0000 Subject: cdc-eem: bad crc checking When the driver received an EEM packet with CRC option enabled, driver must compute and check the CRC of the Ethernet data. Previous version computes CRC on Ethernet data plus the original CRC value. Skbuff is correctly trimed but the old length is used when CRC is computed. Signed-off-by: Vincent CUISSARD Signed-off-by: David S. Miller --- drivers/net/usb/cdc_eem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/usb/cdc_eem.c b/drivers/net/usb/cdc_eem.c index cd35d50e46d4..45cebfb302cf 100644 --- a/drivers/net/usb/cdc_eem.c +++ b/drivers/net/usb/cdc_eem.c @@ -311,7 +311,7 @@ static int eem_rx_fixup(struct usbnet *dev, struct sk_buff *skb) * bmCRC = 0 : CRC = 0xDEADBEEF */ if (header & BIT(14)) - crc2 = ~crc32_le(~0, skb2->data, len); + crc2 = ~crc32_le(~0, skb2->data, skb2->len); else crc2 = 0xdeadbeef; -- cgit v1.2.3 From 8f47428704c2fd6f787a6f340071b9c338b65803 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 13 Jul 2009 22:43:41 +0200 Subject: ataflop: adjust NULL test dtp is derefenced on the lines above the test !dtp, and so it cannot be NULL at this point. A simplified version of the semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r@ expression x,E,E1; identifier f,l; position p1,p2; @@ *x@p1->f = E1; ... when != x = E when != goto l; ( *x@p2 == NULL | *x@p2 != NULL ) // Signed-off-by: Julia Lawall Signed-off-by: Tejun Heo --- drivers/block/ataflop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/block/ataflop.c b/drivers/block/ataflop.c index f5e7180d7f47..3ff02941b3dd 100644 --- a/drivers/block/ataflop.c +++ b/drivers/block/ataflop.c @@ -1627,7 +1627,7 @@ static int fd_ioctl(struct block_device *bdev, fmode_t mode, drive, dtp->blocks, dtp->spt, dtp->stretch); /* sanity check */ - if (!dtp || setprm.track != dtp->blocks/dtp->spt/2 || + if (setprm.track != dtp->blocks/dtp->spt/2 || setprm.head != 2) { redo_fd_request(); return -EINVAL; -- cgit v1.2.3 From 27de22d03d6808a82bbe9bd7e3cc75d60132ba9e Mon Sep 17 00:00:00 2001 From: Davide Libenzi Date: Fri, 17 Jul 2009 21:47:44 -0600 Subject: lguest: remove unnecessary forward struct declaration While fixing lg.h to drop the fwd declaration, I noticed there's another one ;) Signed-off-by: Rusty Russell --- drivers/lguest/lg.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h index 9c3138265f8e..01c591923793 100644 --- a/drivers/lguest/lg.h +++ b/drivers/lguest/lg.h @@ -38,8 +38,6 @@ struct lguest_pages #define CHANGED_GDT_TLS 4 /* Actually a subset of CHANGED_GDT */ #define CHANGED_ALL 3 -struct lguest; - struct lg_cpu { unsigned int id; struct lguest *lg; -- cgit v1.2.3 From 4eff3cae9c9809720c636e64bc72f212258e0bd5 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Fri, 17 Jul 2009 21:47:45 -0600 Subject: virtio_blk: don't bounce highmem requests By default a block driver bounces highmem requests, but virtio-blk is perfectly fine with any request that fit into it's 64 bit addressing scheme, mapped in the kernel virtual space or not. Besides improving performance on highmem systems this also makes the reproducible oops in __bounce_end_io go away (but hiding the real cause). Signed-off-by: Christoph Hellwig Signed-off-by: Rusty Russell --- drivers/block/virtio_blk.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c index 43db3ea15b54..4c47859ad8b1 100644 --- a/drivers/block/virtio_blk.c +++ b/drivers/block/virtio_blk.c @@ -360,6 +360,9 @@ static int __devinit virtblk_probe(struct virtio_device *vdev) blk_queue_max_phys_segments(vblk->disk->queue, vblk->sg_elems-2); blk_queue_max_hw_segments(vblk->disk->queue, vblk->sg_elems-2); + /* No need to bounce any requests */ + blk_queue_bounce_limit(vblk->disk->queue, BLK_BOUNCE_ANY); + /* No real sector limit. */ blk_queue_max_sectors(vblk->disk->queue, -1U); -- cgit v1.2.3 From d9ecdea7ed7467db32ec160f4eca46c279255606 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sat, 20 Jun 2009 21:29:41 +0200 Subject: virtio_blk: ioctl return value fix Block driver ioctl methods must return ENOTTY and not -ENOIOCTLCMD if they expect the block layer to handle generic ioctls. This triggered a BLKROSET failure in xfsqa #200. Signed-off-by: Christoph Hellwig Signed-off-by: Rusty Russell --- drivers/block/virtio_blk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c index 4c47859ad8b1..fbeefb68a31f 100644 --- a/drivers/block/virtio_blk.c +++ b/drivers/block/virtio_blk.c @@ -213,7 +213,7 @@ static int virtblk_ioctl(struct block_device *bdev, fmode_t mode, * Only allow the generic SCSI ioctls if the host can support it. */ if (!virtio_has_feature(vblk->vdev, VIRTIO_BLK_F_SCSI)) - return -ENOIOCTLCMD; + return -ENOTTY; return scsi_cmd_ioctl(disk->queue, disk, mode, cmd, argp); } -- cgit v1.2.3 From 4b892e6582e3a4fe01f623aea386907270d5bf83 Mon Sep 17 00:00:00 2001 From: Mark McLoughlin Date: Tue, 7 Jul 2009 08:26:45 +0100 Subject: virtio-pci: correctly unregister root device on error If pci_register_driver() fails we're incorrectly unregistering the root device with device_unregister() rather than root_device_unregister(). Reported-by: Don Zickus Signed-off-by: Mark McLoughlin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index 193c8f0e5cc5..bcec78ffc765 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -669,7 +669,7 @@ static int __init virtio_pci_init(void) err = pci_register_driver(&virtio_pci_driver); if (err) - device_unregister(virtio_pci_root); + root_device_unregister(virtio_pci_root); return err; } -- cgit v1.2.3 From 2653d1d7f0284f3b68f25dafa208d0a013f7e9db Mon Sep 17 00:00:00 2001 From: Ryan Mallon Date: Wed, 15 Jul 2009 21:33:22 +0100 Subject: [ARM] 5606/1: Fix ep93xx watchdog driver headers Fix a number of build errors in the ep93xx watchdog driver due to missing io.h Signed-off-by: Ryan Mallon Acked-by: H Hartley Sweeten Signed-off-by: Russell King --- drivers/watchdog/ep93xx_wdt.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/watchdog/ep93xx_wdt.c b/drivers/watchdog/ep93xx_wdt.c index e9f950ff86ea..cdd55e0d09f8 100644 --- a/drivers/watchdog/ep93xx_wdt.c +++ b/drivers/watchdog/ep93xx_wdt.c @@ -29,6 +29,7 @@ #include #include #include +#include #include #define WDT_VERSION "0.3" -- cgit v1.2.3 From ecc2e05e739c30870c8e4f252b63a0c4041f2724 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Fri, 17 Jul 2009 16:17:26 +0100 Subject: tty_port: Fix return on interrupted use Whoops.. fortunately not many people use this yet. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/tty_port.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/char/tty_port.c b/drivers/char/tty_port.c index 4e862a75f7ff..9769b1149f76 100644 --- a/drivers/char/tty_port.c +++ b/drivers/char/tty_port.c @@ -267,7 +267,7 @@ int tty_port_block_til_ready(struct tty_port *port, if (retval == 0) port->flags |= ASYNC_NORMAL_ACTIVE; spin_unlock_irqrestore(&port->lock, flags); - return 0; + return retval; } EXPORT_SYMBOL(tty_port_block_til_ready); -- cgit v1.2.3 From 673325951ef440ebace311bd542a9378d1b3025b Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Fri, 17 Jul 2009 04:47:19 +0000 Subject: Update Andreas Koensgen's email address The kernel has used a stale email address of Andreas for a few years. Signed-off-by: Ralf Baechle Signed-off-by: David S. Miller --- CREDITS | 2 +- Documentation/networking/6pack.txt | 2 +- MAINTAINERS | 2 +- drivers/net/hamradio/6pack.c | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/CREDITS b/CREDITS index 2b88fb37ad50..e76d300e9fe4 100644 --- a/CREDITS +++ b/CREDITS @@ -1856,7 +1856,7 @@ E: rfkoenig@immd4.informatik.uni-erlangen.de D: The Linux Support Team Erlangen N: Andreas Koensgen -E: ajk@iehk.rwth-aachen.de +E: ajk@comnets.uni-bremen.de D: 6pack driver for AX.25 N: Harald Koerfgen diff --git a/Documentation/networking/6pack.txt b/Documentation/networking/6pack.txt index d0777a1200e1..8f339428fdf4 100644 --- a/Documentation/networking/6pack.txt +++ b/Documentation/networking/6pack.txt @@ -1,7 +1,7 @@ This is the 6pack-mini-HOWTO, written by Andreas Könsgen DG3KQ -Internet: ajk@iehk.rwth-aachen.de +Internet: ajk@comnets.uni-bremen.de AMPR-net: dg3kq@db0pra.ampr.org AX.25: dg3kq@db0ach.#nrw.deu.eu diff --git a/MAINTAINERS b/MAINTAINERS index 0bd82fa6d2f5..6c6bb95acb15 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -150,7 +150,7 @@ F: drivers/scsi/53c700* 6PACK NETWORK DRIVER FOR AX.25 P: Andreas Koensgen -M: ajk@iehk.rwth-aachen.de +M: ajk@comnets.uni-bremen.de L: linux-hams@vger.kernel.org S: Maintained F: drivers/net/hamradio/6pack.c diff --git a/drivers/net/hamradio/6pack.c b/drivers/net/hamradio/6pack.c index 155160052c8b..981ab530e9ac 100644 --- a/drivers/net/hamradio/6pack.c +++ b/drivers/net/hamradio/6pack.c @@ -3,7 +3,7 @@ * devices like TTY. It interfaces between a raw TTY and the * kernel's AX.25 protocol layers. * - * Authors: Andreas Könsgen + * Authors: Andreas Könsgen * Ralf Baechle DL5RB * * Quite a lot of stuff "stolen" by Joerg Reuter from slip.c, written by -- cgit v1.2.3 From 4fbfff76079a5c0e1751b0ddf53160d33f7831e7 Mon Sep 17 00:00:00 2001 From: Rakib Mullick Date: Fri, 17 Jul 2009 20:13:22 +0600 Subject: virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch The variable virtio_blk references the function virtblk_probe() (which is in .devinit section) and also references the function virtblk_remove() ( which is in .devexit section). So, virtio_blk simultaneously refers .devinit and .devexit section. To avoid this messup, we mark virtio_blk as __refdata. We were warned by the following warning: LD drivers/block/built-in.o WARNING: drivers/block/built-in.o(.data+0xc8dc): Section mismatch in reference from the variable virtio_blk to the function .devinit.text:virtblk_probe() The variable virtio_blk references the function __devinit virtblk_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, WARNING: drivers/block/built-in.o(.data+0xc8e0): Section mismatch in reference from the variable virtio_blk to the function .devexit.text:virtblk_remove() The variable virtio_blk references the function __devexit virtblk_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Rakib Mullick Signed-off-by: Tejun Heo --- drivers/block/virtio_blk.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c index 43db3ea15b54..024f2d292581 100644 --- a/drivers/block/virtio_blk.c +++ b/drivers/block/virtio_blk.c @@ -424,7 +424,12 @@ static unsigned int features[] = { VIRTIO_BLK_F_SCSI, VIRTIO_BLK_F_IDENTIFY }; -static struct virtio_driver virtio_blk = { +/* + * virtio_blk causes spurious section mismatch warning by + * simultaneously referring to a __devinit and a __devexit function. + * Use __refdata to avoid this warning. + */ +static struct virtio_driver __refdata virtio_blk = { .feature_table = features, .feature_table_size = ARRAY_SIZE(features), .driver.name = KBUILD_MODNAME, -- cgit v1.2.3 From 76c317d6e5cb7f58541879006d39774596962715 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 17:26:13 +0200 Subject: HID: Move dereferences below a NULL test If the NULL test is necessary, then the dereferences should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i if (E == NULL||...) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: Jiri Kosina --- drivers/hid/hid-core.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c index f2c21d5d24e8..5eb10c2ce665 100644 --- a/drivers/hid/hid-core.c +++ b/drivers/hid/hid-core.c @@ -1075,14 +1075,16 @@ EXPORT_SYMBOL_GPL(hid_report_raw_event); */ int hid_input_report(struct hid_device *hid, int type, u8 *data, int size, int interrupt) { - struct hid_report_enum *report_enum = hid->report_enum + type; - struct hid_driver *hdrv = hid->driver; + struct hid_report_enum *report_enum; + struct hid_driver *hdrv; struct hid_report *report; unsigned int i; int ret; if (!hid || !hid->driver) return -ENODEV; + report_enum = hid->report_enum + type; + hdrv = hid->driver; if (!size) { dbg_hid("empty report\n"); -- cgit v1.2.3 From a50a97d415d839e6db9df288ff0205528e52c03e Mon Sep 17 00:00:00 2001 From: Wan ZongShun Date: Thu, 16 Jul 2009 02:55:05 +0000 Subject: Add mac driver for w90p910 Add mac driver support for evaluation board based on w90p910. Signed-off-by: Wan ZongShun Signed-off-by: David S. Miller --- drivers/net/arm/Kconfig | 8 + drivers/net/arm/Makefile | 1 + drivers/net/arm/w90p910_ether.c | 1105 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 1114 insertions(+) create mode 100644 drivers/net/arm/w90p910_ether.c (limited to 'drivers') diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig index 2895db13bfa4..c37ee9e6b67b 100644 --- a/drivers/net/arm/Kconfig +++ b/drivers/net/arm/Kconfig @@ -63,3 +63,11 @@ config IXP4XX_ETH help Say Y here if you want to use built-in Ethernet ports on IXP4xx processor. + +config W90P910_ETH + tristate "Nuvoton w90p910 Ethernet support" + depends on ARM && ARCH_W90X900 + select PHYLIB + help + Say Y here if you want to use built-in Ethernet ports + on w90p910 processor. diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile index 811a3ccd14c1..303171f589e6 100644 --- a/drivers/net/arm/Makefile +++ b/drivers/net/arm/Makefile @@ -11,3 +11,4 @@ obj-$(CONFIG_ARM_AT91_ETHER) += at91_ether.o obj-$(CONFIG_ARM_KS8695_ETHER) += ks8695net.o obj-$(CONFIG_EP93XX_ETH) += ep93xx_eth.o obj-$(CONFIG_IXP4XX_ETH) += ixp4xx_eth.o +obj-$(CONFIG_W90P910_ETH) += w90p910_ether.o diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/arm/w90p910_ether.c new file mode 100644 index 000000000000..616fb7985a34 --- /dev/null +++ b/drivers/net/arm/w90p910_ether.c @@ -0,0 +1,1105 @@ +/* + * Copyright (c) 2008-2009 Nuvoton technology corporation. + * + * Wan ZongShun + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation;version 2 of the License. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_MODULE_NAME "w90p910-emc" +#define DRV_MODULE_VERSION "0.1" + +/* Ethernet MAC Registers */ +#define REG_CAMCMR 0x00 +#define REG_CAMEN 0x04 +#define REG_CAMM_BASE 0x08 +#define REG_CAML_BASE 0x0c +#define REG_TXDLSA 0x88 +#define REG_RXDLSA 0x8C +#define REG_MCMDR 0x90 +#define REG_MIID 0x94 +#define REG_MIIDA 0x98 +#define REG_FFTCR 0x9C +#define REG_TSDR 0xa0 +#define REG_RSDR 0xa4 +#define REG_DMARFC 0xa8 +#define REG_MIEN 0xac +#define REG_MISTA 0xb0 +#define REG_CTXDSA 0xcc +#define REG_CTXBSA 0xd0 +#define REG_CRXDSA 0xd4 +#define REG_CRXBSA 0xd8 + +/* mac controller bit */ +#define MCMDR_RXON 0x01 +#define MCMDR_ACP (0x01 << 3) +#define MCMDR_SPCRC (0x01 << 5) +#define MCMDR_TXON (0x01 << 8) +#define MCMDR_FDUP (0x01 << 18) +#define MCMDR_ENMDC (0x01 << 19) +#define MCMDR_OPMOD (0x01 << 20) +#define SWR (0x01 << 24) + +/* cam command regiser */ +#define CAMCMR_AUP 0x01 +#define CAMCMR_AMP (0x01 << 1) +#define CAMCMR_ABP (0x01 << 2) +#define CAMCMR_CCAM (0x01 << 3) +#define CAMCMR_ECMP (0x01 << 4) +#define CAM0EN 0x01 + +/* mac mii controller bit */ +#define MDCCR (0x0a << 20) +#define PHYAD (0x01 << 8) +#define PHYWR (0x01 << 16) +#define PHYBUSY (0x01 << 17) +#define PHYPRESP (0x01 << 18) +#define CAM_ENTRY_SIZE 0x08 + +/* rx and tx status */ +#define TXDS_TXCP (0x01 << 19) +#define RXDS_CRCE (0x01 << 17) +#define RXDS_PTLE (0x01 << 19) +#define RXDS_RXGD (0x01 << 20) +#define RXDS_ALIE (0x01 << 21) +#define RXDS_RP (0x01 << 22) + +/* mac interrupt status*/ +#define MISTA_EXDEF (0x01 << 19) +#define MISTA_TXBERR (0x01 << 24) +#define MISTA_TDU (0x01 << 23) +#define MISTA_RDU (0x01 << 10) +#define MISTA_RXBERR (0x01 << 11) + +#define ENSTART 0x01 +#define ENRXINTR 0x01 +#define ENRXGD (0x01 << 4) +#define ENRXBERR (0x01 << 11) +#define ENTXINTR (0x01 << 16) +#define ENTXCP (0x01 << 18) +#define ENTXABT (0x01 << 21) +#define ENTXBERR (0x01 << 24) +#define ENMDC (0x01 << 19) +#define PHYBUSY (0x01 << 17) +#define MDCCR_VAL 0xa00000 + +/* rx and tx owner bit */ +#define RX_OWEN_DMA (0x01 << 31) +#define RX_OWEN_CPU (~(0x03 << 30)) +#define TX_OWEN_DMA (0x01 << 31) +#define TX_OWEN_CPU (~(0x01 << 31)) + +/* tx frame desc controller bit */ +#define MACTXINTEN 0x04 +#define CRCMODE 0x02 +#define PADDINGMODE 0x01 + +/* fftcr controller bit */ +#define TXTHD (0x03 << 8) +#define BLENGTH (0x01 << 20) + +/* global setting for driver */ +#define RX_DESC_SIZE 50 +#define TX_DESC_SIZE 10 +#define MAX_RBUFF_SZ 0x600 +#define MAX_TBUFF_SZ 0x600 +#define TX_TIMEOUT 50 +#define DELAY 1000 +#define CAM0 0x0 + +static int w90p910_mdio_read(struct net_device *dev, int phy_id, int reg); + +struct w90p910_rxbd { + unsigned int sl; + unsigned int buffer; + unsigned int reserved; + unsigned int next; +}; + +struct w90p910_txbd { + unsigned int mode; + unsigned int buffer; + unsigned int sl; + unsigned int next; +}; + +struct recv_pdesc { + struct w90p910_rxbd desclist[RX_DESC_SIZE]; + char recv_buf[RX_DESC_SIZE][MAX_RBUFF_SZ]; +}; + +struct tran_pdesc { + struct w90p910_txbd desclist[TX_DESC_SIZE]; + char tran_buf[RX_DESC_SIZE][MAX_TBUFF_SZ]; +}; + +struct w90p910_ether { + struct recv_pdesc *rdesc; + struct recv_pdesc *rdesc_phys; + struct tran_pdesc *tdesc; + struct tran_pdesc *tdesc_phys; + struct net_device_stats stats; + struct platform_device *pdev; + struct sk_buff *skb; + struct clk *clk; + struct clk *rmiiclk; + struct mii_if_info mii; + struct timer_list check_timer; + void __iomem *reg; + unsigned int rxirq; + unsigned int txirq; + unsigned int cur_tx; + unsigned int cur_rx; + unsigned int finish_tx; + unsigned int rx_packets; + unsigned int rx_bytes; + unsigned int start_tx_ptr; + unsigned int start_rx_ptr; + unsigned int linkflag; + spinlock_t lock; +}; + +static void update_linkspeed_register(struct net_device *dev, + unsigned int speed, unsigned int duplex) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (speed == SPEED_100) { + /* 100 full/half duplex */ + if (duplex == DUPLEX_FULL) { + val |= (MCMDR_OPMOD | MCMDR_FDUP); + } else { + val |= MCMDR_OPMOD; + val &= ~MCMDR_FDUP; + } + } else { + /* 10 full/half duplex */ + if (duplex == DUPLEX_FULL) { + val |= MCMDR_FDUP; + val &= ~MCMDR_OPMOD; + } else { + val &= ~(MCMDR_FDUP | MCMDR_OPMOD); + } + } + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void update_linkspeed(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int bmsr, bmcr, lpa, speed, duplex; + + pdev = ether->pdev; + + if (!mii_link_ok(ðer->mii)) { + ether->linkflag = 0x0; + netif_carrier_off(dev); + dev_warn(&pdev->dev, "%s: Link down.\n", dev->name); + return; + } + + if (ether->linkflag == 1) + return; + + bmsr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMSR); + bmcr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMCR); + + if (bmcr & BMCR_ANENABLE) { + if (!(bmsr & BMSR_ANEGCOMPLETE)) + return; + + lpa = w90p910_mdio_read(dev, ether->mii.phy_id, MII_LPA); + + if ((lpa & LPA_100FULL) || (lpa & LPA_100HALF)) + speed = SPEED_100; + else + speed = SPEED_10; + + if ((lpa & LPA_100FULL) || (lpa & LPA_10FULL)) + duplex = DUPLEX_FULL; + else + duplex = DUPLEX_HALF; + + } else { + speed = (bmcr & BMCR_SPEED100) ? SPEED_100 : SPEED_10; + duplex = (bmcr & BMCR_FULLDPLX) ? DUPLEX_FULL : DUPLEX_HALF; + } + + update_linkspeed_register(dev, speed, duplex); + + dev_info(&pdev->dev, "%s: Link now %i-%s\n", dev->name, speed, + (duplex == DUPLEX_FULL) ? "FullDuplex" : "HalfDuplex"); + ether->linkflag = 0x01; + + netif_carrier_on(dev); +} + +static void w90p910_check_link(unsigned long dev_id) +{ + struct net_device *dev = (struct net_device *) dev_id; + struct w90p910_ether *ether = netdev_priv(dev); + + update_linkspeed(dev); + mod_timer(ðer->check_timer, jiffies + msecs_to_jiffies(1000)); +} + +static void w90p910_write_cam(struct net_device *dev, + unsigned int x, unsigned char *pval) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int msw, lsw; + + msw = (pval[0] << 24) | (pval[1] << 16) | (pval[2] << 8) | pval[3]; + + lsw = (pval[4] << 24) | (pval[5] << 16); + + __raw_writel(lsw, ether->reg + REG_CAML_BASE + x * CAM_ENTRY_SIZE); + __raw_writel(msw, ether->reg + REG_CAMM_BASE + x * CAM_ENTRY_SIZE); +} + +static void w90p910_init_desc(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *tdesc, *tdesc_phys; + struct w90p910_rxbd *rdesc, *rdesc_phys; + unsigned int i, j; + + ether = netdev_priv(dev); + + ether->tdesc = (struct tran_pdesc *) + dma_alloc_coherent(NULL, sizeof(struct tran_pdesc), + (dma_addr_t *) ðer->tdesc_phys, GFP_KERNEL); + + ether->rdesc = (struct recv_pdesc *) + dma_alloc_coherent(NULL, sizeof(struct recv_pdesc), + (dma_addr_t *) ðer->rdesc_phys, GFP_KERNEL); + + for (i = 0; i < TX_DESC_SIZE; i++) { + tdesc = &(ether->tdesc->desclist[i]); + + j = ((i + 1) / TX_DESC_SIZE); + + if (j != 0) { + tdesc_phys = &(ether->tdesc_phys->desclist[0]); + ether->start_tx_ptr = (unsigned int)tdesc_phys; + tdesc->next = (unsigned int)ether->start_tx_ptr; + } else { + tdesc_phys = &(ether->tdesc_phys->desclist[i+1]); + tdesc->next = (unsigned int)tdesc_phys; + } + + tdesc->buffer = (unsigned int)ether->tdesc_phys->tran_buf[i]; + tdesc->sl = 0; + tdesc->mode = 0; + } + + for (i = 0; i < RX_DESC_SIZE; i++) { + rdesc = &(ether->rdesc->desclist[i]); + + j = ((i + 1) / RX_DESC_SIZE); + + if (j != 0) { + rdesc_phys = &(ether->rdesc_phys->desclist[0]); + ether->start_rx_ptr = (unsigned int)rdesc_phys; + rdesc->next = (unsigned int)ether->start_rx_ptr; + } else { + rdesc_phys = &(ether->rdesc_phys->desclist[i+1]); + rdesc->next = (unsigned int)rdesc_phys; + } + + rdesc->sl = RX_OWEN_DMA; + rdesc->buffer = (unsigned int)ether->rdesc_phys->recv_buf[i]; + } +} + +static void w90p910_set_fifo_threshold(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = TXTHD | BLENGTH; + __raw_writel(val, ether->reg + REG_FFTCR); +} + +static void w90p910_return_default_idle(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + val |= SWR; + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_trigger_rx(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ENSTART, ether->reg + REG_RSDR); +} + +static void w90p910_trigger_tx(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ENSTART, ether->reg + REG_TSDR); +} + +static void w90p910_enable_mac_interrupt(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = ENTXINTR | ENRXINTR | ENRXGD | ENTXCP; + val |= ENTXBERR | ENRXBERR | ENTXABT; + + __raw_writel(val, ether->reg + REG_MIEN); +} + +static void w90p910_get_and_clear_int(struct net_device *dev, + unsigned int *val) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + *val = __raw_readl(ether->reg + REG_MISTA); + __raw_writel(*val, ether->reg + REG_MISTA); +} + +static void w90p910_set_global_maccmd(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + val |= MCMDR_SPCRC | MCMDR_ENMDC | MCMDR_ACP | ENMDC; + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_enable_cam(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + w90p910_write_cam(dev, CAM0, dev->dev_addr); + + val = __raw_readl(ether->reg + REG_CAMEN); + val |= CAM0EN; + __raw_writel(val, ether->reg + REG_CAMEN); +} + +static void w90p910_enable_cam_command(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = CAMCMR_ECMP | CAMCMR_ABP | CAMCMR_AMP; + __raw_writel(val, ether->reg + REG_CAMCMR); +} + +static void w90p910_enable_tx(struct net_device *dev, unsigned int enable) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (enable) + val |= MCMDR_TXON; + else + val &= ~MCMDR_TXON; + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_enable_rx(struct net_device *dev, unsigned int enable) +{ + struct w90p910_ether *ether = netdev_priv(dev); + unsigned int val; + + val = __raw_readl(ether->reg + REG_MCMDR); + + if (enable) + val |= MCMDR_RXON; + else + val &= ~MCMDR_RXON; + + __raw_writel(val, ether->reg + REG_MCMDR); +} + +static void w90p910_set_curdest(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + __raw_writel(ether->start_rx_ptr, ether->reg + REG_RXDLSA); + __raw_writel(ether->start_tx_ptr, ether->reg + REG_TXDLSA); +} + +static void w90p910_reset_mac(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + spin_lock(ðer->lock); + + w90p910_enable_tx(dev, 0); + w90p910_enable_rx(dev, 0); + w90p910_set_fifo_threshold(dev); + w90p910_return_default_idle(dev); + + if (!netif_queue_stopped(dev)) + netif_stop_queue(dev); + + w90p910_init_desc(dev); + + dev->trans_start = jiffies; + ether->cur_tx = 0x0; + ether->finish_tx = 0x0; + ether->cur_rx = 0x0; + + w90p910_set_curdest(dev); + w90p910_enable_cam(dev); + w90p910_enable_cam_command(dev); + w90p910_enable_mac_interrupt(dev); + w90p910_enable_tx(dev, 1); + w90p910_enable_rx(dev, 1); + w90p910_trigger_tx(dev); + w90p910_trigger_rx(dev); + + dev->trans_start = jiffies; + + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + + spin_unlock(ðer->lock); +} + +static void w90p910_mdio_write(struct net_device *dev, + int phy_id, int reg, int data) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int val, i; + + pdev = ether->pdev; + + __raw_writel(data, ether->reg + REG_MIID); + + val = (phy_id << 0x08) | reg; + val |= PHYBUSY | PHYWR | MDCCR_VAL; + __raw_writel(val, ether->reg + REG_MIIDA); + + for (i = 0; i < DELAY; i++) { + if ((__raw_readl(ether->reg + REG_MIIDA) & PHYBUSY) == 0) + break; + } + + if (i == DELAY) + dev_warn(&pdev->dev, "mdio write timed out\n"); +} + +static int w90p910_mdio_read(struct net_device *dev, int phy_id, int reg) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + unsigned int val, i, data; + + pdev = ether->pdev; + + val = (phy_id << 0x08) | reg; + val |= PHYBUSY | MDCCR_VAL; + __raw_writel(val, ether->reg + REG_MIIDA); + + for (i = 0; i < DELAY; i++) { + if ((__raw_readl(ether->reg + REG_MIIDA) & PHYBUSY) == 0) + break; + } + + if (i == DELAY) { + dev_warn(&pdev->dev, "mdio read timed out\n"); + data = 0xffff; + } else { + data = __raw_readl(ether->reg + REG_MIID); + } + + return data; +} + +static int set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *address = addr; + + if (!is_valid_ether_addr(address->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, address->sa_data, dev->addr_len); + w90p910_write_cam(dev, CAM0, dev->dev_addr); + + return 0; +} + +static int w90p910_ether_close(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + dma_free_writecombine(NULL, sizeof(struct w90p910_rxbd), + ether->rdesc, (dma_addr_t)ether->rdesc_phys); + dma_free_writecombine(NULL, sizeof(struct w90p910_txbd), + ether->tdesc, (dma_addr_t)ether->tdesc_phys); + + netif_stop_queue(dev); + + del_timer_sync(ðer->check_timer); + clk_disable(ether->rmiiclk); + clk_disable(ether->clk); + + free_irq(ether->txirq, dev); + free_irq(ether->rxirq, dev); + + return 0; +} + +static struct net_device_stats *w90p910_ether_stats(struct net_device *dev) +{ + struct w90p910_ether *ether; + + ether = netdev_priv(dev); + + return ðer->stats; +} + +static int w90p910_send_frame(struct net_device *dev, + unsigned char *data, int length) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *txbd; + struct platform_device *pdev; + unsigned char *buffer; + + ether = netdev_priv(dev); + pdev = ether->pdev; + + txbd = ðer->tdesc->desclist[ether->cur_tx]; + buffer = ether->tdesc->tran_buf[ether->cur_tx]; + if (length > 1514) { + dev_err(&pdev->dev, "send data %d bytes, check it\n", length); + length = 1514; + } + + txbd->sl = length & 0xFFFF; + + memcpy(buffer, data, length); + + txbd->mode = TX_OWEN_DMA | PADDINGMODE | CRCMODE | MACTXINTEN; + + w90p910_enable_tx(dev, 1); + + w90p910_trigger_tx(dev); + + ether->cur_tx = (ether->cur_tx+1) % TX_DESC_SIZE; + txbd = ðer->tdesc->desclist[ether->cur_tx]; + + dev->trans_start = jiffies; + + if (txbd->mode & TX_OWEN_DMA) + netif_stop_queue(dev); + + return 0; +} + +static int w90p910_ether_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + if (!(w90p910_send_frame(dev, skb->data, skb->len))) { + ether->skb = skb; + dev_kfree_skb_irq(skb); + return 0; + } + return -1; +} + +static irqreturn_t w90p910_tx_interrupt(int irq, void *dev_id) +{ + struct w90p910_ether *ether; + struct w90p910_txbd *txbd; + struct platform_device *pdev; + struct tran_pdesc *tran_pdesc; + struct net_device *dev; + unsigned int cur_entry, entry, status; + + dev = (struct net_device *)dev_id; + ether = netdev_priv(dev); + pdev = ether->pdev; + + spin_lock(ðer->lock); + + w90p910_get_and_clear_int(dev, &status); + + cur_entry = __raw_readl(ether->reg + REG_CTXDSA); + + tran_pdesc = ether->tdesc_phys; + entry = (unsigned int)(&tran_pdesc->desclist[ether->finish_tx]); + + while (entry != cur_entry) { + txbd = ðer->tdesc->desclist[ether->finish_tx]; + + ether->finish_tx = (ether->finish_tx + 1) % TX_DESC_SIZE; + + if (txbd->sl & TXDS_TXCP) { + ether->stats.tx_packets++; + ether->stats.tx_bytes += txbd->sl & 0xFFFF; + } else { + ether->stats.tx_errors++; + } + + txbd->sl = 0x0; + txbd->mode = 0x0; + + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + + entry = (unsigned int)(&tran_pdesc->desclist[ether->finish_tx]); + } + + if (status & MISTA_EXDEF) { + dev_err(&pdev->dev, "emc defer exceed interrupt\n"); + } else if (status & MISTA_TXBERR) { + dev_err(&pdev->dev, "emc bus error interrupt\n"); + w90p910_reset_mac(dev); + } else if (status & MISTA_TDU) { + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + } + + spin_unlock(ðer->lock); + + return IRQ_HANDLED; +} + +static void netdev_rx(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct w90p910_rxbd *rxbd; + struct platform_device *pdev; + struct recv_pdesc *rdesc_phys; + struct sk_buff *skb; + unsigned char *data; + unsigned int length, status, val, entry; + + ether = netdev_priv(dev); + pdev = ether->pdev; + rdesc_phys = ether->rdesc_phys; + + rxbd = ðer->rdesc->desclist[ether->cur_rx]; + + do { + val = __raw_readl(ether->reg + REG_CRXDSA); + entry = (unsigned int)&rdesc_phys->desclist[ether->cur_rx]; + + if (val == entry) + break; + + status = rxbd->sl; + length = status & 0xFFFF; + + if (status & RXDS_RXGD) { + data = ether->rdesc->recv_buf[ether->cur_rx]; + skb = dev_alloc_skb(length+2); + if (!skb) { + dev_err(&pdev->dev, "get skb buffer error\n"); + ether->stats.rx_dropped++; + return; + } + + skb->dev = dev; + skb_reserve(skb, 2); + skb_put(skb, length); + skb_copy_to_linear_data(skb, data, length); + skb->protocol = eth_type_trans(skb, dev); + ether->stats.rx_packets++; + ether->stats.rx_bytes += length; + netif_rx(skb); + } else { + ether->stats.rx_errors++; + + if (status & RXDS_RP) { + dev_err(&pdev->dev, "rx runt err\n"); + ether->stats.rx_length_errors++; + } else if (status & RXDS_CRCE) { + dev_err(&pdev->dev, "rx crc err\n"); + ether->stats.rx_crc_errors++; + } + + if (status & RXDS_ALIE) { + dev_err(&pdev->dev, "rx aligment err\n"); + ether->stats.rx_frame_errors++; + } else if (status & RXDS_PTLE) { + dev_err(&pdev->dev, "rx longer err\n"); + ether->stats.rx_over_errors++; + } + } + + rxbd->sl = RX_OWEN_DMA; + rxbd->reserved = 0x0; + ether->cur_rx = (ether->cur_rx+1) % RX_DESC_SIZE; + rxbd = ðer->rdesc->desclist[ether->cur_rx]; + + dev->last_rx = jiffies; + } while (1); +} + +static irqreturn_t w90p910_rx_interrupt(int irq, void *dev_id) +{ + struct net_device *dev; + struct w90p910_ether *ether; + struct platform_device *pdev; + unsigned int status; + + dev = (struct net_device *)dev_id; + ether = netdev_priv(dev); + pdev = ether->pdev; + + spin_lock(ðer->lock); + + w90p910_get_and_clear_int(dev, &status); + + if (status & MISTA_RDU) { + netdev_rx(dev); + + w90p910_trigger_rx(dev); + + spin_unlock(ðer->lock); + return IRQ_HANDLED; + } else if (status & MISTA_RXBERR) { + dev_err(&pdev->dev, "emc rx bus error\n"); + w90p910_reset_mac(dev); + } + + netdev_rx(dev); + spin_unlock(ðer->lock); + return IRQ_HANDLED; +} + +static int w90p910_ether_open(struct net_device *dev) +{ + struct w90p910_ether *ether; + struct platform_device *pdev; + + ether = netdev_priv(dev); + pdev = ether->pdev; + + w90p910_reset_mac(dev); + w90p910_set_fifo_threshold(dev); + w90p910_set_curdest(dev); + w90p910_enable_cam(dev); + w90p910_enable_cam_command(dev); + w90p910_enable_mac_interrupt(dev); + w90p910_set_global_maccmd(dev); + w90p910_enable_rx(dev, 1); + + ether->rx_packets = 0x0; + ether->rx_bytes = 0x0; + + if (request_irq(ether->txirq, w90p910_tx_interrupt, + 0x0, pdev->name, dev)) { + dev_err(&pdev->dev, "register irq tx failed\n"); + return -EAGAIN; + } + + if (request_irq(ether->rxirq, w90p910_rx_interrupt, + 0x0, pdev->name, dev)) { + dev_err(&pdev->dev, "register irq rx failed\n"); + return -EAGAIN; + } + + mod_timer(ðer->check_timer, jiffies + msecs_to_jiffies(1000)); + netif_start_queue(dev); + w90p910_trigger_rx(dev); + + dev_info(&pdev->dev, "%s is OPENED\n", dev->name); + + return 0; +} + +static void w90p910_ether_set_multicast_list(struct net_device *dev) +{ + struct w90p910_ether *ether; + unsigned int rx_mode; + + ether = netdev_priv(dev); + + if (dev->flags & IFF_PROMISC) + rx_mode = CAMCMR_AUP | CAMCMR_AMP | CAMCMR_ABP | CAMCMR_ECMP; + else if ((dev->flags & IFF_ALLMULTI) || dev->mc_list) + rx_mode = CAMCMR_AMP | CAMCMR_ABP | CAMCMR_ECMP; + else + rx_mode = CAMCMR_ECMP | CAMCMR_ABP; + __raw_writel(rx_mode, ether->reg + REG_CAMCMR); +} + +static int w90p910_ether_ioctl(struct net_device *dev, + struct ifreq *ifr, int cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct mii_ioctl_data *data = if_mii(ifr); + + return generic_mii_ioctl(ðer->mii, data, cmd, NULL); +} + +static void w90p910_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + strcpy(info->driver, DRV_MODULE_NAME); + strcpy(info->version, DRV_MODULE_VERSION); +} + +static int w90p910_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_ethtool_gset(ðer->mii, cmd); +} + +static int w90p910_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_ethtool_sset(ðer->mii, cmd); +} + +static int w90p910_nway_reset(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_nway_restart(ðer->mii); +} + +static u32 w90p910_get_link(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + return mii_link_ok(ðer->mii); +} + +static const struct ethtool_ops w90p910_ether_ethtool_ops = { + .get_settings = w90p910_get_settings, + .set_settings = w90p910_set_settings, + .get_drvinfo = w90p910_get_drvinfo, + .nway_reset = w90p910_nway_reset, + .get_link = w90p910_get_link, +}; + +static const struct net_device_ops w90p910_ether_netdev_ops = { + .ndo_open = w90p910_ether_open, + .ndo_stop = w90p910_ether_close, + .ndo_start_xmit = w90p910_ether_start_xmit, + .ndo_get_stats = w90p910_ether_stats, + .ndo_set_multicast_list = w90p910_ether_set_multicast_list, + .ndo_set_mac_address = set_mac_address, + .ndo_do_ioctl = w90p910_ether_ioctl, + .ndo_validate_addr = eth_validate_addr, + .ndo_change_mtu = eth_change_mtu, +}; + +static void __init get_mac_address(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + struct platform_device *pdev; + char addr[6]; + + pdev = ether->pdev; + + addr[0] = 0x00; + addr[1] = 0x02; + addr[2] = 0xac; + addr[3] = 0x55; + addr[4] = 0x88; + addr[5] = 0xa8; + + if (is_valid_ether_addr(addr)) + memcpy(dev->dev_addr, &addr, 0x06); + else + dev_err(&pdev->dev, "invalid mac address\n"); +} + +static int w90p910_ether_setup(struct net_device *dev) +{ + struct w90p910_ether *ether = netdev_priv(dev); + + ether_setup(dev); + dev->netdev_ops = &w90p910_ether_netdev_ops; + dev->ethtool_ops = &w90p910_ether_ethtool_ops; + + dev->tx_queue_len = 16; + dev->dma = 0x0; + dev->watchdog_timeo = TX_TIMEOUT; + + get_mac_address(dev); + + spin_lock_init(ðer->lock); + + ether->cur_tx = 0x0; + ether->cur_rx = 0x0; + ether->finish_tx = 0x0; + ether->linkflag = 0x0; + ether->mii.phy_id = 0x01; + ether->mii.phy_id_mask = 0x1f; + ether->mii.reg_num_mask = 0x1f; + ether->mii.dev = dev; + ether->mii.mdio_read = w90p910_mdio_read; + ether->mii.mdio_write = w90p910_mdio_write; + + setup_timer(ðer->check_timer, w90p910_check_link, + (unsigned long)dev); + + return 0; +} + +static int __devinit w90p910_ether_probe(struct platform_device *pdev) +{ + struct w90p910_ether *ether; + struct net_device *dev; + struct resource *res; + int error; + + dev = alloc_etherdev(sizeof(struct w90p910_ether)); + if (!dev) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) { + dev_err(&pdev->dev, "failed to get I/O memory\n"); + error = -ENXIO; + goto failed_free; + } + + res = request_mem_region(res->start, resource_size(res), pdev->name); + if (res == NULL) { + dev_err(&pdev->dev, "failed to request I/O memory\n"); + error = -EBUSY; + goto failed_free; + } + + ether = netdev_priv(dev); + + ether->reg = ioremap(res->start, resource_size(res)); + if (ether->reg == NULL) { + dev_err(&pdev->dev, "failed to remap I/O memory\n"); + error = -ENXIO; + goto failed_free_mem; + } + + ether->txirq = platform_get_irq(pdev, 0); + if (ether->txirq < 0) { + dev_err(&pdev->dev, "failed to get ether tx irq\n"); + error = -ENXIO; + goto failed_free_io; + } + + ether->rxirq = platform_get_irq(pdev, 1); + if (ether->rxirq < 0) { + dev_err(&pdev->dev, "failed to get ether rx irq\n"); + error = -ENXIO; + goto failed_free_txirq; + } + + platform_set_drvdata(pdev, dev); + + ether->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(ether->clk)) { + dev_err(&pdev->dev, "failed to get ether clock\n"); + error = PTR_ERR(ether->clk); + goto failed_free_rxirq; + } + + ether->rmiiclk = clk_get(&pdev->dev, "RMII"); + if (IS_ERR(ether->rmiiclk)) { + dev_err(&pdev->dev, "failed to get ether clock\n"); + error = PTR_ERR(ether->rmiiclk); + goto failed_put_clk; + } + + ether->pdev = pdev; + + w90p910_ether_setup(dev); + + error = register_netdev(dev); + if (error != 0) { + dev_err(&pdev->dev, "Regiter EMC w90p910 FAILED\n"); + error = -ENODEV; + goto failed_put_rmiiclk; + } + + return 0; +failed_put_rmiiclk: + clk_put(ether->rmiiclk); +failed_put_clk: + clk_put(ether->clk); +failed_free_rxirq: + free_irq(ether->rxirq, pdev); + platform_set_drvdata(pdev, NULL); +failed_free_txirq: + free_irq(ether->txirq, pdev); +failed_free_io: + iounmap(ether->reg); +failed_free_mem: + release_mem_region(res->start, resource_size(res)); +failed_free: + free_netdev(dev); + return error; +} + +static int __devexit w90p910_ether_remove(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct w90p910_ether *ether = netdev_priv(dev); + + unregister_netdev(dev); + clk_put(ether->rmiiclk); + clk_put(ether->clk); + del_timer_sync(ðer->check_timer); + platform_set_drvdata(pdev, NULL); + free_netdev(dev); + return 0; +} + +static struct platform_driver w90p910_ether_driver = { + .probe = w90p910_ether_probe, + .remove = __devexit_p(w90p910_ether_remove), + .driver = { + .name = "w90p910-emc", + .owner = THIS_MODULE, + }, +}; + +static int __init w90p910_ether_init(void) +{ + return platform_driver_register(&w90p910_ether_driver); +} + +static void __exit w90p910_ether_exit(void) +{ + platform_driver_unregister(&w90p910_ether_driver); +} + +module_init(w90p910_ether_init); +module_exit(w90p910_ether_exit); + +MODULE_AUTHOR("Wan ZongShun "); +MODULE_DESCRIPTION("w90p910 MAC driver!"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:w90p910-emc"); + -- cgit v1.2.3 From 3ba81f3ece3cfa4ffb06d21ac93b8cad7fbe6a73 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 16 Jul 2009 05:24:08 +0000 Subject: net: Micrel KS8851 SPI network driver Network driver for the SPI version of the Micrel KS8851 network chip. Signed-off-by: Ben Dooks Signed-off-by: David S. Miller --- drivers/net/Kconfig | 6 + drivers/net/Makefile | 1 + drivers/net/ks8851.c | 1322 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/ks8851.h | 296 +++++++++++ 4 files changed, 1625 insertions(+) create mode 100644 drivers/net/ks8851.c create mode 100644 drivers/net/ks8851.h (limited to 'drivers') diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index c155bd3ec9f1..b5a7513df4eb 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1729,6 +1729,12 @@ config KS8842 help This platform driver is for Micrel KSZ8842 chip. +config KS8851 + tristate "Micrel KS8851 SPI" + depends on SPI + help + SPI driver for Micrel KS8851 SPI attached network chip. + config VIA_RHINE tristate "VIA Rhine support" depends on NET_PCI && PCI diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 4b58a59f211b..ead8cab3cfe1 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -88,6 +88,7 @@ obj-$(CONFIG_SKGE) += skge.o obj-$(CONFIG_SKY2) += sky2.o obj-$(CONFIG_SKFP) += skfp/ obj-$(CONFIG_KS8842) += ks8842.o +obj-$(CONFIG_KS8851) += ks8851.o obj-$(CONFIG_VIA_RHINE) += via-rhine.o obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o diff --git a/drivers/net/ks8851.c b/drivers/net/ks8851.c new file mode 100644 index 000000000000..9a1dea60c1c4 --- /dev/null +++ b/drivers/net/ks8851.c @@ -0,0 +1,1322 @@ +/* drivers/net/ks8651.c + * + * Copyright 2009 Simtec Electronics + * http://www.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define DEBUG + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "ks8851.h" + +/** + * struct ks8851_rxctrl - KS8851 driver rx control + * @mchash: Multicast hash-table data. + * @rxcr1: KS_RXCR1 register setting + * @rxcr2: KS_RXCR2 register setting + * + * Representation of the settings needs to control the receive filtering + * such as the multicast hash-filter and the receive register settings. This + * is used to make the job of working out if the receive settings change and + * then issuing the new settings to the worker that will send the necessary + * commands. + */ +struct ks8851_rxctrl { + u16 mchash[4]; + u16 rxcr1; + u16 rxcr2; +}; + +/** + * union ks8851_tx_hdr - tx header data + * @txb: The header as bytes + * @txw: The header as 16bit, little-endian words + * + * A dual representation of the tx header data to allow + * access to individual bytes, and to allow 16bit accesses + * with 16bit alignment. + */ +union ks8851_tx_hdr { + u8 txb[6]; + __le16 txw[3]; +}; + +/** + * struct ks8851_net - KS8851 driver private data + * @netdev: The network device we're bound to + * @spidev: The spi device we're bound to. + * @lock: Lock to ensure that the device is not accessed when busy. + * @statelock: Lock on this structure for tx list. + * @mii: The MII state information for the mii calls. + * @rxctrl: RX settings for @rxctrl_work. + * @tx_work: Work queue for tx packets + * @irq_work: Work queue for servicing interrupts + * @rxctrl_work: Work queue for updating RX mode and multicast lists + * @txq: Queue of packets for transmission. + * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1. + * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2. + * @txh: Space for generating packet TX header in DMA-able data + * @rxd: Space for receiving SPI data, in DMA-able space. + * @txd: Space for transmitting SPI data, in DMA-able space. + * @msg_enable: The message flags controlling driver output (see ethtool). + * @fid: Incrementing frame id tag. + * @rc_ier: Cached copy of KS_IER. + * @rc_rxqcr: Cached copy of KS_RXQCR. + * + * The @lock ensures that the chip is protected when certain operations are + * in progress. When the read or write packet transfer is in progress, most + * of the chip registers are not ccessible until the transfer is finished and + * the DMA has been de-asserted. + * + * The @statelock is used to protect information in the structure which may + * need to be accessed via several sources, such as the network driver layer + * or one of the work queues. + * + * We align the buffers we may use for rx/tx to ensure that if the SPI driver + * wants to DMA map them, it will not have any problems with data the driver + * modifies. + */ +struct ks8851_net { + struct net_device *netdev; + struct spi_device *spidev; + struct mutex lock; + spinlock_t statelock; + + union ks8851_tx_hdr txh ____cacheline_aligned; + u8 rxd[8]; + u8 txd[8]; + + u32 msg_enable ____cacheline_aligned; + u16 tx_space; + u8 fid; + + u16 rc_ier; + u16 rc_rxqcr; + + struct mii_if_info mii; + struct ks8851_rxctrl rxctrl; + + struct work_struct tx_work; + struct work_struct irq_work; + struct work_struct rxctrl_work; + + struct sk_buff_head txq; + + struct spi_message spi_msg1; + struct spi_message spi_msg2; + struct spi_transfer spi_xfer1; + struct spi_transfer spi_xfer2[2]; +}; + +static int msg_enable; + +#define ks_info(_ks, _msg...) dev_info(&(_ks)->spidev->dev, _msg) +#define ks_warn(_ks, _msg...) dev_warn(&(_ks)->spidev->dev, _msg) +#define ks_dbg(_ks, _msg...) dev_dbg(&(_ks)->spidev->dev, _msg) +#define ks_err(_ks, _msg...) dev_err(&(_ks)->spidev->dev, _msg) + +/* shift for byte-enable data */ +#define BYTE_EN(_x) ((_x) << 2) + +/* turn register number and byte-enable mask into data for start of packet */ +#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6) + +/* SPI register read/write calls. + * + * All these calls issue SPI transactions to access the chip's registers. They + * all require that the necessary lock is held to prevent accesses when the + * chip is busy transfering packet data (RX/TX FIFO accesses). + */ + +/** + * ks8851_wrreg16 - write 16bit register value to chip + * @ks: The chip state + * @reg: The register address + * @val: The value to write + * + * Issue a write to put the value @val into the register specified in @reg. + */ +static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val) +{ + struct spi_transfer *xfer = &ks->spi_xfer1; + struct spi_message *msg = &ks->spi_msg1; + __le16 txb[2]; + int ret; + + txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR); + txb[1] = cpu_to_le16(val); + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 4; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "spi_sync() failed\n"); +} + +/** + * ks8851_rx_1msg - select whether to use one or two messages for spi read + * @ks: The device structure + * + * Return whether to generate a single message with a tx and rx buffer + * supplied to spi_sync(), or alternatively send the tx and rx buffers + * as separate messages. + * + * Depending on the hardware in use, a single message may be more efficient + * on interrupts or work done by the driver. + * + * This currently always returns true until we add some per-device data passed + * from the platform code to specify which mode is better. + */ +static inline bool ks8851_rx_1msg(struct ks8851_net *ks) +{ + return true; +} + +/** + * ks8851_rdreg - issue read register command and return the data + * @ks: The device state + * @op: The register address and byte enables in message format. + * @rxb: The RX buffer to return the result into + * @rxl: The length of data expected. + * + * This is the low level read call that issues the necessary spi message(s) + * to read data from the register specified in @op. + */ +static void ks8851_rdreg(struct ks8851_net *ks, unsigned op, + u8 *rxb, unsigned rxl) +{ + struct spi_transfer *xfer; + struct spi_message *msg; + __le16 *txb = (__le16 *)ks->txd; + u8 *trx = ks->rxd; + int ret; + + txb[0] = cpu_to_le16(op | KS_SPIOP_RD); + + if (ks8851_rx_1msg(ks)) { + msg = &ks->spi_msg1; + xfer = &ks->spi_xfer1; + + xfer->tx_buf = txb; + xfer->rx_buf = trx; + xfer->len = rxl + 2; + } else { + msg = &ks->spi_msg2; + xfer = ks->spi_xfer2; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 2; + + xfer++; + xfer->tx_buf = NULL; + xfer->rx_buf = trx; + xfer->len = rxl; + } + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "read: spi_sync() failed\n"); + else if (ks8851_rx_1msg(ks)) + memcpy(rxb, trx + 2, rxl); + else + memcpy(rxb, trx, rxl); +} + +/** + * ks8851_rdreg8 - read 8 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 8bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg) +{ + u8 rxb[1]; + + ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1); + return rxb[0]; +} + +/** + * ks8851_rdreg16 - read 16 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 16bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg) +{ + __le16 rx = 0; + + ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2); + return le16_to_cpu(rx); +} + +/** + * ks8851_rdreg32 - read 32 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 32bit register from the chip. + * + * Note, this read requires the address be aligned to 4 bytes. +*/ +static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg) +{ + __le32 rx = 0; + + WARN_ON(reg & 3); + + ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4); + return le32_to_cpu(rx); +} + +/** + * ks8851_soft_reset - issue one of the soft reset to the device + * @ks: The device state. + * @op: The bit(s) to set in the GRR + * + * Issue the relevant soft-reset command to the device's GRR register + * specified by @op. + * + * Note, the delays are in there as a caution to ensure that the reset + * has time to take effect and then complete. Since the datasheet does + * not currently specify the exact sequence, we have chosen something + * that seems to work with our device. + */ +static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op) +{ + ks8851_wrreg16(ks, KS_GRR, op); + mdelay(1); /* wait a short time to effect reset */ + ks8851_wrreg16(ks, KS_GRR, 0); + mdelay(1); /* wait for condition to clear */ +} + +/** + * ks8851_write_mac_addr - write mac address to device registers + * @dev: The network device + * + * Update the KS8851 MAC address registers from the address in @dev. + * + * This call assumes that the chip is not running, so there is no need to + * shutdown the RXQ process whilst setting this. +*/ +static int ks8851_write_mac_addr(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + u16 *mcp = (u16 *)dev->dev_addr; + + mutex_lock(&ks->lock); + + ks8851_wrreg16(ks, KS_MARL, mcp[0]); + ks8851_wrreg16(ks, KS_MARM, mcp[1]); + ks8851_wrreg16(ks, KS_MARH, mcp[2]); + + mutex_unlock(&ks->lock); + + return 0; +} + +/** + * ks8851_init_mac - initialise the mac address + * @ks: The device structure + * + * Get or create the initial mac address for the device and then set that + * into the station address register. Currently we assume that the device + * does not have a valid mac address in it, and so we use random_ether_addr() + * to create a new one. + * + * In future, the driver should check to see if the device has an EEPROM + * attached and whether that has a valid ethernet address in it. + */ +static void ks8851_init_mac(struct ks8851_net *ks) +{ + struct net_device *dev = ks->netdev; + + random_ether_addr(dev->dev_addr); + ks8851_write_mac_addr(dev); +} + +/** + * ks8851_irq - device interrupt handler + * @irq: Interrupt number passed from the IRQ hnalder. + * @pw: The private word passed to register_irq(), our struct ks8851_net. + * + * Disable the interrupt from happening again until we've processed the + * current status by scheduling ks8851_irq_work(). + */ +static irqreturn_t ks8851_irq(int irq, void *pw) +{ + struct ks8851_net *ks = pw; + + disable_irq_nosync(irq); + schedule_work(&ks->irq_work); + return IRQ_HANDLED; +} + +/** + * ks8851_rdfifo - read data from the receive fifo + * @ks: The device state. + * @buff: The buffer address + * @len: The length of the data to read + * + * Issue an RXQ FIFO read command and read the @len ammount of data from + * the FIFO into the buffer specified by @buff. + */ +static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + u8 txb[1]; + int ret; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d@%p\n", __func__, len, buff); + + /* set the operation we're issuing */ + txb[0] = KS_SPIOP_RXFIFO; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 1; + + xfer++; + xfer->rx_buf = buff; + xfer->tx_buf = NULL; + xfer->len = len; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_dbg_dumpkkt - dump initial packet contents to debug + * @ks: The device state + * @rxpkt: The data for the received packet + * + * Dump the initial data from the packet to dev_dbg(). +*/ +static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt) +{ + ks_dbg(ks, "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n", + rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7], + rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11], + rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]); +} + +/** + * ks8851_rx_pkts - receive packets from the host + * @ks: The device information. + * + * This is called from the IRQ work queue when the system detects that there + * are packets in the receive queue. Find out how many packets there are and + * read them from the FIFO. + */ +static void ks8851_rx_pkts(struct ks8851_net *ks) +{ + struct sk_buff *skb; + unsigned rxfc; + unsigned rxlen; + unsigned rxstat; + u32 rxh; + u8 *rxpkt; + + rxfc = ks8851_rdreg8(ks, KS_RXFC); + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d packets\n", __func__, rxfc); + + /* Currently we're issuing a read per packet, but we could possibly + * improve the code by issuing a single read, getting the receive + * header, allocating the packet and then reading the packet data + * out in one go. + * + * This form of operation would require us to hold the SPI bus' + * chipselect low during the entie transaction to avoid any + * reset to the data stream comming from the chip. + */ + + for (; rxfc != 0; rxfc--) { + rxh = ks8851_rdreg32(ks, KS_RXFHSR); + rxstat = rxh & 0xffff; + rxlen = rxh >> 16; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "rx: stat 0x%04x, len 0x%04x\n", + rxstat, rxlen); + + /* the length of the packet includes the 32bit CRC */ + + /* set dma read address */ + ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00); + + /* start the packet dma process, and set auto-dequeue rx */ + ks8851_wrreg16(ks, KS_RXQCR, + ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE); + + if (rxlen > 0) { + skb = netdev_alloc_skb(ks->netdev, rxlen + 2 + 8); + if (!skb) { + /* todo - dump frame and move on */ + } + + /* two bytes to ensure ip is aligned, and four bytes + * for the status header and 4 bytes of garbage */ + skb_reserve(skb, 2 + 4 + 4); + + rxpkt = skb_put(skb, rxlen - 4) - 8; + + /* align the packet length to 4 bytes, and add 4 bytes + * as we're getting the rx status header as well */ + ks8851_rdfifo(ks, rxpkt, ALIGN(rxlen, 4) + 8); + + if (netif_msg_pktdata(ks)) + ks8851_dbg_dumpkkt(ks, rxpkt); + + skb->protocol = eth_type_trans(skb, ks->netdev); + netif_rx(skb); + + ks->netdev->stats.rx_packets++; + ks->netdev->stats.rx_bytes += rxlen - 4; + } + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + } +} + +/** + * ks8851_irq_work - work queue handler for dealing with interrupt requests + * @work: The work structure that was scheduled by schedule_work() + * + * This is the handler invoked when the ks8851_irq() is called to find out + * what happened, as we cannot allow ourselves to sleep whilst waiting for + * anything other process has the chip's lock. + * + * Read the interrupt status, work out what needs to be done and then clear + * any of the interrupts that are not needed. + */ +static void ks8851_irq_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work); + unsigned status; + unsigned handled = 0; + + mutex_lock(&ks->lock); + + status = ks8851_rdreg16(ks, KS_ISR); + + if (netif_msg_intr(ks)) + dev_dbg(&ks->spidev->dev, "%s: status 0x%04x\n", + __func__, status); + + if (status & IRQ_LCI) { + /* should do something about checking link status */ + handled |= IRQ_LCI; + } + + if (status & IRQ_LDI) { + u16 pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_WKEVT_MASK; + ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK); + + handled |= IRQ_LDI; + } + + if (status & IRQ_RXPSI) + handled |= IRQ_RXPSI; + + if (status & IRQ_TXI) { + handled |= IRQ_TXI; + + /* no lock here, tx queue should have been stopped */ + + /* update our idea of how much tx space is available to the + * system */ + ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR); + + if (netif_msg_intr(ks)) + ks_dbg(ks, "%s: txspace %d\n", __func__, ks->tx_space); + } + + if (status & IRQ_RXI) + handled |= IRQ_RXI; + + if (status & IRQ_SPIBEI) { + dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__); + handled |= IRQ_SPIBEI; + } + + ks8851_wrreg16(ks, KS_ISR, handled); + + if (status & IRQ_RXI) { + /* the datasheet says to disable the rx interrupt during + * packet read-out, however we're masking the interrupt + * from the device so do not bother masking just the RX + * from the device. */ + + ks8851_rx_pkts(ks); + } + + /* if something stopped the rx process, probably due to wanting + * to change the rx settings, then do something about restarting + * it. */ + if (status & IRQ_RXPSI) { + struct ks8851_rxctrl *rxc = &ks->rxctrl; + + /* update the multicast hash table */ + ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]); + ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]); + ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]); + ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]); + + ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2); + ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1); + } + + mutex_unlock(&ks->lock); + + if (status & IRQ_TXI) + netif_wake_queue(ks->netdev); + + enable_irq(ks->netdev->irq); +} + +/** + * calc_txlen - calculate size of message to send packet + * @len: Lenght of data + * + * Returns the size of the TXFIFO message needed to send + * this packet. + */ +static inline unsigned calc_txlen(unsigned len) +{ + return ALIGN(len + 4, 4); +} + +/** + * ks8851_wrpkt - write packet to TX FIFO + * @ks: The device state. + * @txp: The sk_buff to transmit. + * @irq: IRQ on completion of the packet. + * + * Send the @txp to the chip. This means creating the relevant packet header + * specifying the length of the packet and the other information the chip + * needs, such as IRQ on completion. Send the header and the packet data to + * the device. + */ +static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + unsigned fid = 0; + int ret; + + if (netif_msg_tx_queued(ks)) + dev_dbg(&ks->spidev->dev, "%s: skb %p, %d@%p, irq %d\n", + __func__, txp, txp->len, txp->data, irq); + + fid = ks->fid++; + fid &= TXFR_TXFID_MASK; + + if (irq) + fid |= TXFR_TXIC; /* irq on completion */ + + /* start header at txb[1] to align txw entries */ + ks->txh.txb[1] = KS_SPIOP_TXFIFO; + ks->txh.txw[1] = cpu_to_le16(fid); + ks->txh.txw[2] = cpu_to_le16(txp->len); + + xfer->tx_buf = &ks->txh.txb[1]; + xfer->rx_buf = NULL; + xfer->len = 5; + + xfer++; + xfer->tx_buf = txp->data; + xfer->rx_buf = NULL; + xfer->len = ALIGN(txp->len, 4); + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_done_tx - update and then free skbuff after transmitting + * @ks: The device state + * @txb: The buffer transmitted + */ +static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb) +{ + struct net_device *dev = ks->netdev; + + dev->stats.tx_bytes += txb->len; + dev->stats.tx_packets++; + + dev_kfree_skb(txb); +} + +/** + * ks8851_tx_work - process tx packet(s) + * @work: The work strucutre what was scheduled. + * + * This is called when a number of packets have been scheduled for + * transmission and need to be sent to the device. + */ +static void ks8851_tx_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work); + struct sk_buff *txb; + bool last = false; + + mutex_lock(&ks->lock); + + while (!last) { + txb = skb_dequeue(&ks->txq); + last = skb_queue_empty(&ks->txq); + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA); + ks8851_wrpkt(ks, txb, last); + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE); + + ks8851_done_tx(ks, txb); + } + + mutex_unlock(&ks->lock); +} + +/** + * ks8851_set_powermode - set power mode of the device + * @ks: The device state + * @pwrmode: The power mode value to write to KS_PMECR. + * + * Change the power mode of the chip. + */ +static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode) +{ + unsigned pmecr; + + if (netif_msg_hw(ks)) + ks_dbg(ks, "setting power mode %d\n", pwrmode); + + pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_PM_MASK; + pmecr |= pwrmode; + + ks8851_wrreg16(ks, KS_PMECR, pmecr); +} + +/** + * ks8851_net_open - open network device + * @dev: The network device being opened. + * + * Called when the network device is marked active, such as a user executing + * 'ifconfig up' on the device. + */ +static int ks8851_net_open(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + /* lock the card, even if we may not actually be doing anything + * else at the moment */ + mutex_lock(&ks->lock); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "opening %s\n", dev->name); + + /* bring chip out of any power saving mode it was in */ + ks8851_set_powermode(ks, PMECR_PM_NORMAL); + + /* issue a soft reset to the RX/TX QMU to put it into a known + * state. */ + ks8851_soft_reset(ks, GRR_QMU); + + /* setup transmission parameters */ + + ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */ + TXCR_TXPE | /* pad to min length */ + TXCR_TXCRC | /* add CRC */ + TXCR_TXFCE)); /* enable flow control */ + + /* auto-increment tx data, reset tx pointer */ + ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI); + + /* setup receiver control */ + + ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */ + RXCR1_RXFCE | /* enable flow control */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXUE | /* unicast enable */ + RXCR1_RXE)); /* enable rx block */ + + /* transfer entire frames out in one go */ + ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME); + + /* set receive counter timeouts */ + ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */ + ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */ + ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */ + + ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */ + RXQCR_RXDBCTE | /* IRQ on byte count exceeded */ + RXQCR_RXDTTE); /* IRQ on time exceeded */ + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + + /* clear then enable interrupts */ + +#define STD_IRQ (IRQ_LCI | /* Link Change */ \ + IRQ_TXI | /* TX done */ \ + IRQ_RXI | /* RX done */ \ + IRQ_SPIBEI | /* SPI bus error */ \ + IRQ_TXPSI | /* TX process stop */ \ + IRQ_RXPSI) /* RX process stop */ + + ks->rc_ier = STD_IRQ; + ks8851_wrreg16(ks, KS_ISR, STD_IRQ); + ks8851_wrreg16(ks, KS_IER, STD_IRQ); + + netif_start_queue(ks->netdev); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "network device %s up\n", dev->name); + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_net_stop - close network device + * @dev: The device being closed. + * + * Called to close down a network device which has been active. Cancell any + * work, shutdown the RX and TX process and then place the chip into a low + * power state whilst it is not being used. + */ +static int ks8851_net_stop(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (netif_msg_ifdown(ks)) + ks_info(ks, "%s: shutting down\n", dev->name); + + netif_stop_queue(dev); + + mutex_lock(&ks->lock); + + /* stop any outstanding work */ + flush_work(&ks->irq_work); + flush_work(&ks->tx_work); + flush_work(&ks->rxctrl_work); + + /* turn off the IRQs and ack any outstanding */ + ks8851_wrreg16(ks, KS_IER, 0x0000); + ks8851_wrreg16(ks, KS_ISR, 0xffff); + + /* shutdown RX process */ + ks8851_wrreg16(ks, KS_RXCR1, 0x0000); + + /* shutdown TX process */ + ks8851_wrreg16(ks, KS_TXCR, 0x0000); + + /* set powermode to soft power down to save power */ + ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + + /* ensure any queued tx buffers are dumped */ + while (!skb_queue_empty(&ks->txq)) { + struct sk_buff *txb = skb_dequeue(&ks->txq); + + if (netif_msg_ifdown(ks)) + ks_dbg(ks, "%s: freeing txb %p\n", __func__, txb); + + dev_kfree_skb(txb); + } + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_start_xmit - transmit packet + * @skb: The buffer to transmit + * @dev: The device used to transmit the packet. + * + * Called by the network layer to transmit the @skb. Queue the packet for + * the device and schedule the necessary work to transmit the packet when + * it is free. + * + * We do this to firstly avoid sleeping with the network device locked, + * and secondly so we can round up more than one packet to transmit which + * means we can try and avoid generating too many transmit done interrupts. + */ +static int ks8851_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + unsigned needed = calc_txlen(skb->len); + int ret = NETDEV_TX_OK; + + if (netif_msg_tx_queued(ks)) + ks_dbg(ks, "%s: skb %p, %d@%p\n", __func__, + skb, skb->len, skb->data); + + spin_lock(&ks->statelock); + + if (needed > ks->tx_space) { + netif_stop_queue(dev); + ret = NETDEV_TX_BUSY; + } else { + ks->tx_space -= needed; + skb_queue_tail(&ks->txq, skb); + } + + spin_unlock(&ks->statelock); + schedule_work(&ks->tx_work); + + return ret; +} + +/** + * ks8851_rxctrl_work - work handler to change rx mode + * @work: The work structure this belongs to. + * + * Lock the device and issue the necessary changes to the receive mode from + * the network device layer. This is done so that we can do this without + * having to sleep whilst holding the network device lock. + * + * Since the recommendation from Micrel is that the RXQ is shutdown whilst the + * receive parameters are programmed, we issue a write to disable the RXQ and + * then wait for the interrupt handler to be triggered once the RXQ shutdown is + * complete. The interrupt handler then writes the new values into the chip. + */ +static void ks8851_rxctrl_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work); + + mutex_lock(&ks->lock); + + /* need to shutdown RXQ before modifying filter parameters */ + ks8851_wrreg16(ks, KS_RXCR1, 0x00); + + mutex_unlock(&ks->lock); +} + +static void ks8851_set_rx_mode(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + struct ks8851_rxctrl rxctrl; + + memset(&rxctrl, 0, sizeof(rxctrl)); + + if (dev->flags & IFF_PROMISC) { + /* interface to receive everything */ + + rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF; + } else if (dev->flags & IFF_ALLMULTI) { + /* accept all multicast packets */ + + rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE | + RXCR1_RXPAFMA | RXCR1_RXMAFMA); + } else if (dev->flags & IFF_MULTICAST && dev->mc_count > 0) { + struct dev_mc_list *mcptr = dev->mc_list; + u32 crc; + int i; + + /* accept some multicast */ + + for (i = dev->mc_count; i > 0; i--) { + crc = ether_crc(ETH_ALEN, mcptr->dmi_addr); + crc >>= (32 - 6); /* get top six bits */ + + rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf)); + mcptr = mcptr->next; + } + + rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXAE | RXCR1_RXPAFMA; + } else { + /* just accept broadcast / unicast */ + rxctrl.rxcr1 = RXCR1_RXPAFMA; + } + + rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXE | /* RX process enable */ + RXCR1_RXFCE); /* enable flow control */ + + rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME; + + /* schedule work to do the actual set of the data if needed */ + + spin_lock(&ks->statelock); + + if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) { + memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl)); + schedule_work(&ks->rxctrl_work); + } + + spin_unlock(&ks->statelock); +} + +static int ks8851_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *sa = addr; + + if (netif_running(dev)) + return -EBUSY; + + if (!is_valid_ether_addr(sa->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN); + return ks8851_write_mac_addr(dev); +} + +static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (!netif_running(dev)) + return -EINVAL; + + return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL); +} + +static const struct net_device_ops ks8851_netdev_ops = { + .ndo_open = ks8851_net_open, + .ndo_stop = ks8851_net_stop, + .ndo_do_ioctl = ks8851_net_ioctl, + .ndo_start_xmit = ks8851_start_xmit, + .ndo_set_mac_address = ks8851_set_mac_address, + .ndo_set_rx_mode = ks8851_set_rx_mode, + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, +}; + +/* ethtool support */ + +static void ks8851_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *di) +{ + strlcpy(di->driver, "KS8851", sizeof(di->driver)); + strlcpy(di->version, "1.00", sizeof(di->version)); + strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info)); +} + +static u32 ks8851_get_msglevel(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return ks->msg_enable; +} + +static void ks8851_set_msglevel(struct net_device *dev, u32 to) +{ + struct ks8851_net *ks = netdev_priv(dev); + ks->msg_enable = to; +} + +static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_gset(&ks->mii, cmd); +} + +static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_sset(&ks->mii, cmd); +} + +static u32 ks8851_get_link(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_link_ok(&ks->mii); +} + +static int ks8851_nway_reset(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_nway_restart(&ks->mii); +} + +static const struct ethtool_ops ks8851_ethtool_ops = { + .get_drvinfo = ks8851_get_drvinfo, + .get_msglevel = ks8851_get_msglevel, + .set_msglevel = ks8851_set_msglevel, + .get_settings = ks8851_get_settings, + .set_settings = ks8851_set_settings, + .get_link = ks8851_get_link, + .nway_reset = ks8851_nway_reset, +}; + +/* MII interface controls */ + +/** + * ks8851_phy_reg - convert MII register into a KS8851 register + * @reg: MII register number. + * + * Return the KS8851 register number for the corresponding MII PHY register + * if possible. Return zero if the MII register has no direct mapping to the + * KS8851 register set. + */ +static int ks8851_phy_reg(int reg) +{ + switch (reg) { + case MII_BMCR: + return KS_P1MBCR; + case MII_BMSR: + return KS_P1MBSR; + case MII_PHYSID1: + return KS_PHY1ILR; + case MII_PHYSID2: + return KS_PHY1IHR; + case MII_ADVERTISE: + return KS_P1ANAR; + case MII_LPA: + return KS_P1ANLPR; + } + + return 0x0; +} + +/** + * ks8851_phy_read - MII interface PHY register read. + * @dev: The network device the PHY is on. + * @phy_addr: Address of PHY (ignored as we only have one) + * @reg: The register to read. + * + * This call reads data from the PHY register specified in @reg. Since the + * device does not support all the MII registers, the non-existant values + * are always returned as zero. + * + * We return zero for unsupported registers as the MII code does not check + * the value returned for any error status, and simply returns it to the + * caller. The mii-tool that the driver was tested with takes any -ve error + * as real PHY capabilities, thus displaying incorrect data to the user. + */ +static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + int result; + + ksreg = ks8851_phy_reg(reg); + if (!ksreg) + return 0x0; /* no error return allowed, so use zero */ + + mutex_lock(&ks->lock); + result = ks8851_rdreg16(ks, ksreg); + mutex_unlock(&ks->lock); + + return result; +} + +static void ks8851_phy_write(struct net_device *dev, + int phy, int reg, int value) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + + ksreg = ks8851_phy_reg(reg); + if (ksreg) { + mutex_lock(&ks->lock); + ks8851_wrreg16(ks, ksreg, value); + mutex_unlock(&ks->lock); + } +} + +/** + * ks8851_read_selftest - read the selftest memory info. + * @ks: The device state + * + * Read and check the TX/RX memory selftest information. + */ +static int ks8851_read_selftest(struct ks8851_net *ks) +{ + unsigned both_done = MBIR_TXMBF | MBIR_RXMBF; + int ret = 0; + unsigned rd; + + rd = ks8851_rdreg16(ks, KS_MBIR); + + if ((rd & both_done) != both_done) { + ks_warn(ks, "Memory selftest not finished\n"); + return 0; + } + + if (rd & MBIR_TXMBFA) { + ks_err(ks, "TX memory selftest fail\n"); + ret |= 1; + } + + if (rd & MBIR_RXMBFA) { + ks_err(ks, "RX memory selftest fail\n"); + ret |= 2; + } + + return 0; +} + +/* driver bus management functions */ + +static int __devinit ks8851_probe(struct spi_device *spi) +{ + struct net_device *ndev; + struct ks8851_net *ks; + int ret; + + ndev = alloc_etherdev(sizeof(struct ks8851_net)); + if (!ndev) { + dev_err(&spi->dev, "failed to alloc ethernet device\n"); + return -ENOMEM; + } + + spi->bits_per_word = 8; + + ks = netdev_priv(ndev); + + ks->netdev = ndev; + ks->spidev = spi; + ks->tx_space = 6144; + + mutex_init(&ks->lock); + spin_lock_init(&ks->statelock); + + INIT_WORK(&ks->tx_work, ks8851_tx_work); + INIT_WORK(&ks->irq_work, ks8851_irq_work); + INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work); + + /* initialise pre-made spi transfer messages */ + + spi_message_init(&ks->spi_msg1); + spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1); + + spi_message_init(&ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2); + + /* setup mii state */ + ks->mii.dev = ndev; + ks->mii.phy_id = 1, + ks->mii.phy_id_mask = 1; + ks->mii.reg_num_mask = 0xf; + ks->mii.mdio_read = ks8851_phy_read; + ks->mii.mdio_write = ks8851_phy_write; + + dev_info(&spi->dev, "message enable is %d\n", msg_enable); + + /* set the default message enable */ + ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV | + NETIF_MSG_PROBE | + NETIF_MSG_LINK)); + + skb_queue_head_init(&ks->txq); + + SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops); + SET_NETDEV_DEV(ndev, &spi->dev); + + dev_set_drvdata(&spi->dev, ks); + + ndev->if_port = IF_PORT_100BASET; + ndev->netdev_ops = &ks8851_netdev_ops; + ndev->irq = spi->irq; + + /* simple check for a valid chip being connected to the bus */ + + if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) { + dev_err(&spi->dev, "failed to read device ID\n"); + ret = -ENODEV; + goto err_id; + } + + ks8851_read_selftest(ks); + ks8851_init_mac(ks); + + ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW, + ndev->name, ks); + if (ret < 0) { + dev_err(&spi->dev, "failed to get irq\n"); + goto err_irq; + } + + ret = register_netdev(ndev); + if (ret) { + dev_err(&spi->dev, "failed to register network device\n"); + goto err_netdev; + } + + dev_info(&spi->dev, "revision %d, MAC %pM, IRQ %d\n", + CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)), + ndev->dev_addr, ndev->irq); + + return 0; + + +err_netdev: + free_irq(ndev->irq, ndev); + +err_id: +err_irq: + free_netdev(ndev); + return ret; +} + +static int __devexit ks8851_remove(struct spi_device *spi) +{ + struct ks8851_net *priv = dev_get_drvdata(&spi->dev); + + if (netif_msg_drv(priv)) + dev_info(&spi->dev, "remove"); + + unregister_netdev(priv->netdev); + free_irq(spi->irq, priv); + free_netdev(priv->netdev); + + return 0; +} + +static struct spi_driver ks8851_driver = { + .driver = { + .name = "ks8851", + .owner = THIS_MODULE, + }, + .probe = ks8851_probe, + .remove = __devexit_p(ks8851_remove), +}; + +static int __init ks8851_init(void) +{ + return spi_register_driver(&ks8851_driver); +} + +static void __exit ks8851_exit(void) +{ + spi_unregister_driver(&ks8851_driver); +} + +module_init(ks8851_init); +module_exit(ks8851_exit); + +MODULE_DESCRIPTION("KS8851 Network driver"); +MODULE_AUTHOR("Ben Dooks "); +MODULE_LICENSE("GPL"); + +module_param_named(message, msg_enable, int, 0); +MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)"); diff --git a/drivers/net/ks8851.h b/drivers/net/ks8851.h new file mode 100644 index 000000000000..85abe147afbf --- /dev/null +++ b/drivers/net/ks8851.h @@ -0,0 +1,296 @@ +/* drivers/net/ks8851.h + * + * Copyright 2009 Simtec Electronics + * Ben Dooks + * + * KS8851 register definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define KS_CCR 0x08 +#define CCR_EEPROM (1 << 9) +#define CCR_SPI (1 << 8) +#define CCR_32PIN (1 << 0) + +/* MAC address registers */ +#define KS_MARL 0x10 +#define KS_MARM 0x12 +#define KS_MARH 0x14 + +#define KS_OBCR 0x20 +#define OBCR_ODS_16mA (1 << 6) + +#define KS_EEPCR 0x22 +#define EEPCR_EESA (1 << 4) +#define EEPCR_EESB (1 << 3) +#define EEPCR_EEDO (1 << 2) +#define EEPCR_EESCK (1 << 1) +#define EEPCR_EECS (1 << 0) + +#define KS_MBIR 0x24 +#define MBIR_TXMBF (1 << 12) +#define MBIR_TXMBFA (1 << 11) +#define MBIR_RXMBF (1 << 4) +#define MBIR_RXMBFA (1 << 3) + +#define KS_GRR 0x26 +#define GRR_QMU (1 << 1) +#define GRR_GSR (1 << 0) + +#define KS_WFCR 0x2A +#define WFCR_MPRXE (1 << 7) +#define WFCR_WF3E (1 << 3) +#define WFCR_WF2E (1 << 2) +#define WFCR_WF1E (1 << 1) +#define WFCR_WF0E (1 << 0) + +#define KS_WF0CRC0 0x30 +#define KS_WF0CRC1 0x32 +#define KS_WF0BM0 0x34 +#define KS_WF0BM1 0x36 +#define KS_WF0BM2 0x38 +#define KS_WF0BM3 0x3A + +#define KS_WF1CRC0 0x40 +#define KS_WF1CRC1 0x42 +#define KS_WF1BM0 0x44 +#define KS_WF1BM1 0x46 +#define KS_WF1BM2 0x48 +#define KS_WF1BM3 0x4A + +#define KS_WF2CRC0 0x50 +#define KS_WF2CRC1 0x52 +#define KS_WF2BM0 0x54 +#define KS_WF2BM1 0x56 +#define KS_WF2BM2 0x58 +#define KS_WF2BM3 0x5A + +#define KS_WF3CRC0 0x60 +#define KS_WF3CRC1 0x62 +#define KS_WF3BM0 0x64 +#define KS_WF3BM1 0x66 +#define KS_WF3BM2 0x68 +#define KS_WF3BM3 0x6A + +#define KS_TXCR 0x70 +#define TXCR_TCGICMP (1 << 8) +#define TXCR_TCGUDP (1 << 7) +#define TXCR_TCGTCP (1 << 6) +#define TXCR_TCGIP (1 << 5) +#define TXCR_FTXQ (1 << 4) +#define TXCR_TXFCE (1 << 3) +#define TXCR_TXPE (1 << 2) +#define TXCR_TXCRC (1 << 1) +#define TXCR_TXE (1 << 0) + +#define KS_TXSR 0x72 +#define TXSR_TXLC (1 << 13) +#define TXSR_TXMC (1 << 12) +#define TXSR_TXFID_MASK (0x3f << 0) +#define TXSR_TXFID_SHIFT (0) +#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f) + +#define KS_RXCR1 0x74 +#define RXCR1_FRXQ (1 << 15) +#define RXCR1_RXUDPFCC (1 << 14) +#define RXCR1_RXTCPFCC (1 << 13) +#define RXCR1_RXIPFCC (1 << 12) +#define RXCR1_RXPAFMA (1 << 11) +#define RXCR1_RXFCE (1 << 10) +#define RXCR1_RXEFE (1 << 9) +#define RXCR1_RXMAFMA (1 << 8) +#define RXCR1_RXBE (1 << 7) +#define RXCR1_RXME (1 << 6) +#define RXCR1_RXUE (1 << 5) +#define RXCR1_RXAE (1 << 4) +#define RXCR1_RXINVF (1 << 1) +#define RXCR1_RXE (1 << 0) + +#define KS_RXCR2 0x76 +#define RXCR2_SRDBL_MASK (0x7 << 5) +#define RXCR2_SRDBL_SHIFT (5) +#define RXCR2_SRDBL_4B (0x0 << 5) +#define RXCR2_SRDBL_8B (0x1 << 5) +#define RXCR2_SRDBL_16B (0x2 << 5) +#define RXCR2_SRDBL_32B (0x3 << 5) +#define RXCR2_SRDBL_FRAME (0x4 << 5) +#define RXCR2_IUFFP (1 << 4) +#define RXCR2_RXIUFCEZ (1 << 3) +#define RXCR2_UDPLFE (1 << 2) +#define RXCR2_RXICMPFCC (1 << 1) +#define RXCR2_RXSAF (1 << 0) + +#define KS_TXMIR 0x78 + +#define KS_RXFHSR 0x7C +#define RXFSHR_RXFV (1 << 15) +#define RXFSHR_RXICMPFCS (1 << 13) +#define RXFSHR_RXIPFCS (1 << 12) +#define RXFSHR_RXTCPFCS (1 << 11) +#define RXFSHR_RXUDPFCS (1 << 10) +#define RXFSHR_RXBF (1 << 7) +#define RXFSHR_RXMF (1 << 6) +#define RXFSHR_RXUF (1 << 5) +#define RXFSHR_RXMR (1 << 4) +#define RXFSHR_RXFT (1 << 3) +#define RXFSHR_RXFTL (1 << 2) +#define RXFSHR_RXRF (1 << 1) +#define RXFSHR_RXCE (1 << 0) + +#define KS_RXFHBCR 0x7E +#define KS_TXQCR 0x80 +#define TXQCR_AETFE (1 << 2) +#define TXQCR_TXQMAM (1 << 1) +#define TXQCR_METFE (1 << 0) + +#define KS_RXQCR 0x82 +#define RXQCR_RXDTTS (1 << 12) +#define RXQCR_RXDBCTS (1 << 11) +#define RXQCR_RXFCTS (1 << 10) +#define RXQCR_RXIPHTOE (1 << 9) +#define RXQCR_RXDTTE (1 << 7) +#define RXQCR_RXDBCTE (1 << 6) +#define RXQCR_RXFCTE (1 << 5) +#define RXQCR_ADRFE (1 << 4) +#define RXQCR_SDA (1 << 3) +#define RXQCR_RRXEF (1 << 0) + +#define KS_TXFDPR 0x84 +#define TXFDPR_TXFPAI (1 << 14) +#define TXFDPR_TXFP_MASK (0x7ff << 0) +#define TXFDPR_TXFP_SHIFT (0) + +#define KS_RXFDPR 0x86 +#define RXFDPR_RXFPAI (1 << 14) + +#define KS_RXDTTR 0x8C +#define KS_RXDBCTR 0x8E + +#define KS_IER 0x90 +#define KS_ISR 0x92 +#define IRQ_LCI (1 << 15) +#define IRQ_TXI (1 << 14) +#define IRQ_RXI (1 << 13) +#define IRQ_RXOI (1 << 11) +#define IRQ_TXPSI (1 << 9) +#define IRQ_RXPSI (1 << 8) +#define IRQ_TXSAI (1 << 6) +#define IRQ_RXWFDI (1 << 5) +#define IRQ_RXMPDI (1 << 4) +#define IRQ_LDI (1 << 3) +#define IRQ_EDI (1 << 2) +#define IRQ_SPIBEI (1 << 1) +#define IRQ_DEDI (1 << 0) + +#define KS_RXFCTR 0x9C +#define KS_RXFC 0x9D +#define RXFCTR_RXFC_MASK (0xff << 8) +#define RXFCTR_RXFC_SHIFT (8) +#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff) +#define RXFCTR_RXFCT_MASK (0xff << 0) +#define RXFCTR_RXFCT_SHIFT (0) + +#define KS_TXNTFSR 0x9E + +#define KS_MAHTR0 0xA0 +#define KS_MAHTR1 0xA2 +#define KS_MAHTR2 0xA4 +#define KS_MAHTR3 0xA6 + +#define KS_FCLWR 0xB0 +#define KS_FCHWR 0xB2 +#define KS_FCOWR 0xB4 + +#define KS_CIDER 0xC0 +#define CIDER_ID 0x8870 +#define CIDER_REV_MASK (0x7 << 1) +#define CIDER_REV_SHIFT (1) +#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7) + +#define KS_CGCR 0xC6 + +#define KS_IACR 0xC8 +#define IACR_RDEN (1 << 12) +#define IACR_TSEL_MASK (0x3 << 10) +#define IACR_TSEL_SHIFT (10) +#define IACR_TSEL_MIB (0x3 << 10) +#define IACR_ADDR_MASK (0x1f << 0) +#define IACR_ADDR_SHIFT (0) + +#define KS_IADLR 0xD0 +#define KS_IAHDR 0xD2 + +#define KS_PMECR 0xD4 +#define PMECR_PME_DELAY (1 << 14) +#define PMECR_PME_POL (1 << 12) +#define PMECR_WOL_WAKEUP (1 << 11) +#define PMECR_WOL_MAGICPKT (1 << 10) +#define PMECR_WOL_LINKUP (1 << 9) +#define PMECR_WOL_ENERGY (1 << 8) +#define PMECR_AUTO_WAKE_EN (1 << 7) +#define PMECR_WAKEUP_NORMAL (1 << 6) +#define PMECR_WKEVT_MASK (0xf << 2) +#define PMECR_WKEVT_SHIFT (2) +#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf) +#define PMECR_WKEVT_ENERGY (0x1 << 2) +#define PMECR_WKEVT_LINK (0x2 << 2) +#define PMECR_WKEVT_MAGICPKT (0x4 << 2) +#define PMECR_WKEVT_FRAME (0x8 << 2) +#define PMECR_PM_MASK (0x3 << 0) +#define PMECR_PM_SHIFT (0) +#define PMECR_PM_NORMAL (0x0 << 0) +#define PMECR_PM_ENERGY (0x1 << 0) +#define PMECR_PM_SOFTDOWN (0x2 << 0) +#define PMECR_PM_POWERSAVE (0x3 << 0) + +/* Standard MII PHY data */ +#define KS_P1MBCR 0xE4 +#define KS_P1MBSR 0xE6 +#define KS_PHY1ILR 0xE8 +#define KS_PHY1IHR 0xEA +#define KS_P1ANAR 0xEC +#define KS_P1ANLPR 0xEE + +#define KS_P1SCLMD 0xF4 +#define P1SCLMD_LEDOFF (1 << 15) +#define P1SCLMD_TXIDS (1 << 14) +#define P1SCLMD_RESTARTAN (1 << 13) +#define P1SCLMD_DISAUTOMDIX (1 << 10) +#define P1SCLMD_FORCEMDIX (1 << 9) +#define P1SCLMD_AUTONEGEN (1 << 7) +#define P1SCLMD_FORCE100 (1 << 6) +#define P1SCLMD_FORCEFDX (1 << 5) +#define P1SCLMD_ADV_FLOW (1 << 4) +#define P1SCLMD_ADV_100BT_FDX (1 << 3) +#define P1SCLMD_ADV_100BT_HDX (1 << 2) +#define P1SCLMD_ADV_10BT_FDX (1 << 1) +#define P1SCLMD_ADV_10BT_HDX (1 << 0) + +#define KS_P1CR 0xF6 +#define P1CR_HP_MDIX (1 << 15) +#define P1CR_REV_POL (1 << 13) +#define P1CR_OP_100M (1 << 10) +#define P1CR_OP_FDX (1 << 9) +#define P1CR_OP_MDI (1 << 7) +#define P1CR_AN_DONE (1 << 6) +#define P1CR_LINK_GOOD (1 << 5) +#define P1CR_PNTR_FLOW (1 << 4) +#define P1CR_PNTR_100BT_FDX (1 << 3) +#define P1CR_PNTR_100BT_HDX (1 << 2) +#define P1CR_PNTR_10BT_FDX (1 << 1) +#define P1CR_PNTR_10BT_HDX (1 << 0) + +/* TX Frame control */ + +#define TXFR_TXIC (1 << 15) +#define TXFR_TXFID_MASK (0x3f << 0) +#define TXFR_TXFID_SHIFT (0) + +/* SPI frame opcodes */ +#define KS_SPIOP_RD (0x00) +#define KS_SPIOP_WR (0x40) +#define KS_SPIOP_RXFIFO (0x80) +#define KS_SPIOP_TXFIFO (0xC0) -- cgit v1.2.3 From cf981ffb31e8f41f4899a56560f81322f94f22d1 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:06 +0000 Subject: netxen: fix context deletion sequence o Use D3 reset context deletion for NX2031, it cleans up more resources in the firmware. o Release rx buffers after hardware context has been reset. o Delete tx context after rx context, some firmware control commands are sent on tx context, so it should be the last to go. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 1 + drivers/net/netxen/netxen_nic_ctx.c | 13 +++++++------ drivers/net/netxen/netxen_nic_main.c | 2 +- 3 files changed, 9 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index e1cdba752e09..9fa71faf4ceb 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -210,6 +210,7 @@ #define NETXEN_CTX_SIGNATURE 0xdee0 #define NETXEN_CTX_SIGNATURE_V2 0x0002dee0 #define NETXEN_CTX_RESET 0xbad0 +#define NETXEN_CTX_D3_RESET 0xacc0 #define NETXEN_RCV_PRODUCER(ringid) (ringid) #define PHAN_PEG_RCV_INITIALIZED 0xff01 diff --git a/drivers/net/netxen/netxen_nic_ctx.c b/drivers/net/netxen/netxen_nic_ctx.c index 4754f5cffad0..9f8ae4719e2f 100644 --- a/drivers/net/netxen/netxen_nic_ctx.c +++ b/drivers/net/netxen/netxen_nic_ctx.c @@ -684,10 +684,8 @@ int netxen_alloc_hw_resources(struct netxen_adapter *adapter) goto err_out_free; } else { err = netxen_init_old_ctx(adapter); - if (err) { - netxen_free_hw_resources(adapter); - return err; - } + if (err) + goto err_out_free; } return 0; @@ -708,15 +706,18 @@ void netxen_free_hw_resources(struct netxen_adapter *adapter) int port = adapter->portnum; if (adapter->fw_major >= 4) { - nx_fw_cmd_destroy_tx_ctx(adapter); nx_fw_cmd_destroy_rx_ctx(adapter); + nx_fw_cmd_destroy_tx_ctx(adapter); } else { netxen_api_lock(adapter); NXWR32(adapter, CRB_CTX_SIGNATURE_REG(port), - NETXEN_CTX_RESET | port); + NETXEN_CTX_D3_RESET | port); netxen_api_unlock(adapter); } + /* Allow dma queues to drain after context reset */ + msleep(20); + recv_ctx = &adapter->recv_ctx; if (recv_ctx->hwctx != NULL) { diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 27539ddf94c4..9a7c4c8029de 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -943,8 +943,8 @@ err_out_free_sw: static void netxen_nic_detach(struct netxen_adapter *adapter) { - netxen_release_rx_buffers(adapter); netxen_free_hw_resources(adapter); + netxen_release_rx_buffers(adapter); netxen_nic_free_irq(adapter); netxen_free_sw_resources(adapter); -- cgit v1.2.3 From b2af9cb06d4de1b507ec0fd779ec2ecedee1480a Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:07 +0000 Subject: netxen: fix deadlock on dev close netxen: fix deadlock on dev close The tx ring accounting fix in commit cb2107be43d2fc5eadec58b92b ("netxen: fix tx ring accounting") introduced intermittent deadlock when inteface is going down. This was possibly combined effect of speculative tx pause, calling netif_tx_lock instead of queue lock and unclean synchronization with napi which could end up unmasking interrupt. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 2 ++ drivers/net/netxen/netxen_nic_hw.c | 9 +++++---- drivers/net/netxen/netxen_nic_init.c | 5 +++-- drivers/net/netxen/netxen_nic_main.c | 20 +++++++++++++------- 4 files changed, 23 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index 9fa71faf4ceb..f86e05047d19 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -774,6 +774,8 @@ struct nx_host_tx_ring { u32 crb_cmd_consumer; u32 num_desc; + struct netdev_queue *txq; + struct netxen_cmd_buffer *cmd_buf_arr; struct cmd_desc_type0 *desc_head; dma_addr_t phys_addr; diff --git a/drivers/net/netxen/netxen_nic_hw.c b/drivers/net/netxen/netxen_nic_hw.c index ce3b89d2cbb6..b9123d445c96 100644 --- a/drivers/net/netxen/netxen_nic_hw.c +++ b/drivers/net/netxen/netxen_nic_hw.c @@ -461,13 +461,14 @@ netxen_send_cmd_descs(struct netxen_adapter *adapter, i = 0; tx_ring = adapter->tx_ring; - netif_tx_lock_bh(adapter->netdev); + __netif_tx_lock_bh(tx_ring->txq); producer = tx_ring->producer; consumer = tx_ring->sw_consumer; - if (nr_desc >= find_diff_among(producer, consumer, tx_ring->num_desc)) { - netif_tx_unlock_bh(adapter->netdev); + if (nr_desc >= netxen_tx_avail(tx_ring)) { + netif_tx_stop_queue(tx_ring->txq); + __netif_tx_unlock_bh(tx_ring->txq); return -EBUSY; } @@ -490,7 +491,7 @@ netxen_send_cmd_descs(struct netxen_adapter *adapter, netxen_nic_update_cmd_producer(adapter, tx_ring); - netif_tx_unlock_bh(adapter->netdev); + __netif_tx_unlock_bh(tx_ring->txq); return 0; } diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index b899bd51fcd8..5d3343ef3d86 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -214,6 +214,7 @@ int netxen_alloc_sw_resources(struct netxen_adapter *adapter) adapter->tx_ring = tx_ring; tx_ring->num_desc = adapter->num_txd; + tx_ring->txq = netdev_get_tx_queue(netdev, 0); cmd_buf_arr = vmalloc(TX_BUFF_RINGSIZE(tx_ring)); if (cmd_buf_arr == NULL) { @@ -1400,10 +1401,10 @@ int netxen_process_cmd_ring(struct netxen_adapter *adapter) smp_mb(); if (netif_queue_stopped(netdev) && netif_carrier_ok(netdev)) { - netif_tx_lock(netdev); + __netif_tx_lock(tx_ring->txq, smp_processor_id()); if (netxen_tx_avail(tx_ring) > TX_STOP_THRESH) netif_wake_queue(netdev); - netif_tx_unlock(netdev); + __netif_tx_unlock(tx_ring->txq); } } /* diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 9a7c4c8029de..370c52f27760 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -215,9 +215,9 @@ netxen_napi_disable(struct netxen_adapter *adapter) for (ring = 0; ring < adapter->max_sds_rings; ring++) { sds_ring = &recv_ctx->sds_rings[ring]; - napi_disable(&sds_ring->napi); netxen_nic_disable_int(sds_ring); - synchronize_irq(sds_ring->irq); + napi_synchronize(&sds_ring->napi); + napi_disable(&sds_ring->napi); } } @@ -833,11 +833,11 @@ netxen_nic_up(struct netxen_adapter *adapter, struct net_device *netdev) adapter->ahw.linkup = 0; - netxen_napi_enable(adapter); - if (adapter->max_sds_rings > 1) netxen_config_rss(adapter, 1); + netxen_napi_enable(adapter); + if (adapter->capabilities & NX_FW_CAPABILITY_LINK_NOTIFICATION) netxen_linkevent_request(adapter, 1); else @@ -851,8 +851,9 @@ netxen_nic_up(struct netxen_adapter *adapter, struct net_device *netdev) static void netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) { + spin_lock(&adapter->tx_clean_lock); netif_carrier_off(netdev); - netif_stop_queue(netdev); + netif_tx_disable(netdev); if (adapter->stop_port) adapter->stop_port(adapter); @@ -863,9 +864,10 @@ netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) netxen_napi_disable(adapter); netxen_release_tx_buffers(adapter); + spin_unlock(&adapter->tx_clean_lock); - FLUSH_SCHEDULED_WORK(); del_timer_sync(&adapter->watchdog_timer); + FLUSH_SCHEDULED_WORK(); } @@ -1645,6 +1647,9 @@ static void netxen_tx_timeout_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, tx_timeout_task); + if (!netif_running(adapter->netdev)) + return; + printk(KERN_ERR "%s %s: transmit timeout, resetting.\n", netxen_nic_driver_name, adapter->netdev->name); @@ -1757,7 +1762,8 @@ static int netxen_nic_poll(struct napi_struct *napi, int budget) if ((work_done < budget) && tx_complete) { napi_complete(&sds_ring->napi); - netxen_nic_enable_int(sds_ring); + if (netif_running(adapter->netdev)) + netxen_nic_enable_int(sds_ring); } return work_done; -- cgit v1.2.3 From e4135c2da11c337e3759f98727c4819ba2a849fa Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Fri, 17 Jul 2009 15:27:08 +0000 Subject: netxen: fix thermal check and shutdown Check temperature for all PCI functions, that can allow graceful shutdown of all interfaces on the overheated card. Old code was only monitoring temperature for function 0 only. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 370c52f27760..637ac8b89bac 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -1535,10 +1535,12 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) printk(KERN_ALERT "%s: Device temperature %d degrees C exceeds" " maximum allowed. Hardware has been shut down.\n", - netxen_nic_driver_name, temp_val); + netdev->name, temp_val); + + netif_device_detach(netdev); + netxen_nic_down(adapter, netdev); + netxen_nic_detach(adapter); - netif_carrier_off(netdev); - netif_stop_queue(netdev); rv = 1; } else if (temp_state == NX_TEMP_WARN) { if (adapter->temp == NX_TEMP_NORMAL) { @@ -1546,13 +1548,13 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) "%s: Device temperature %d degrees C " "exceeds operating range." " Immediate action needed.\n", - netxen_nic_driver_name, temp_val); + netdev->name, temp_val); } } else { if (adapter->temp == NX_TEMP_WARN) { printk(KERN_INFO "%s: Device temperature is now %d degrees C" - " in normal range.\n", netxen_nic_driver_name, + " in normal range.\n", netdev->name, temp_val); } } @@ -1625,7 +1627,7 @@ void netxen_watchdog_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, watchdog_task); - if ((adapter->portnum == 0) && netxen_nic_check_temp(adapter)) + if (netxen_nic_check_temp(adapter)) return; if (!adapter->has_link_events) -- cgit v1.2.3 From e445bb4ed677f8df0d4f8c1abc15c668bd182f28 Mon Sep 17 00:00:00 2001 From: Ken Kawasaki Date: Sun, 19 Jul 2009 13:08:12 +0000 Subject: 3c589_cs: re-initialize the multicast in the tc589_reset 3c589_cs: re-initialize the multicast in the tc589_reset, and spin_lock the set_multicast_list function. Signed-off-by: Ken Kawasaki Signed-off-by: David S. Miller --- drivers/net/pcmcia/3c589_cs.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/net/pcmcia/3c589_cs.c b/drivers/net/pcmcia/3c589_cs.c index ec7cf5ac4f05..690b9c76d34e 100644 --- a/drivers/net/pcmcia/3c589_cs.c +++ b/drivers/net/pcmcia/3c589_cs.c @@ -156,6 +156,7 @@ static struct net_device_stats *el3_get_stats(struct net_device *dev); static int el3_rx(struct net_device *dev); static int el3_close(struct net_device *dev); static void el3_tx_timeout(struct net_device *dev); +static void set_rx_mode(struct net_device *dev); static void set_multicast_list(struct net_device *dev); static const struct ethtool_ops netdev_ethtool_ops; @@ -488,8 +489,7 @@ static void tc589_reset(struct net_device *dev) /* Switch to register set 1 for normal use. */ EL3WINDOW(1); - /* Accept b-cast and phys addr only. */ - outw(SetRxFilter | RxStation | RxBroadcast, ioaddr + EL3_CMD); + set_rx_mode(dev); outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */ outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */ outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */ @@ -700,7 +700,7 @@ static irqreturn_t el3_interrupt(int irq, void *dev_id) if (fifo_diag & 0x2000) { /* Rx underrun */ tc589_wait_for_completion(dev, RxReset); - set_multicast_list(dev); + set_rx_mode(dev); outw(RxEnable, ioaddr + EL3_CMD); } outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD); @@ -905,14 +905,11 @@ static int el3_rx(struct net_device *dev) return 0; } -static void set_multicast_list(struct net_device *dev) +static void set_rx_mode(struct net_device *dev) { - struct el3_private *lp = netdev_priv(dev); - struct pcmcia_device *link = lp->p_dev; unsigned int ioaddr = dev->base_addr; u16 opts = SetRxFilter | RxStation | RxBroadcast; - if (!pcmcia_dev_present(link)) return; if (dev->flags & IFF_PROMISC) opts |= RxMulticast | RxProm; else if (dev->mc_count || (dev->flags & IFF_ALLMULTI)) @@ -920,6 +917,16 @@ static void set_multicast_list(struct net_device *dev) outw(opts, ioaddr + EL3_CMD); } +static void set_multicast_list(struct net_device *dev) +{ + struct el3_private *priv = netdev_priv(dev); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + set_rx_mode(dev); + spin_unlock_irqrestore(&priv->lock, flags); +} + static int el3_close(struct net_device *dev) { struct el3_private *lp = netdev_priv(dev); -- cgit v1.2.3 From 90cb665937a2aab16d9aa60f22908195c16dcffd Mon Sep 17 00:00:00 2001 From: Cesar Eduardo Barros Date: Sun, 19 Jul 2009 08:03:32 +0000 Subject: New device ID for sc92031 [1088:2031] MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit rain_maker@root-forum.org wrote: > Hello cesar, > > In a recent thread in a german linux forum, a user reported his PIC > NIC not being recognized by the kernel. > > Fortunately he provided enough information and I was able to help him > and get the device working with the sc92031 driver. > > The device ID is [1088:2031] (Vendor is called "Microcomputer Systems > (M) Son"), here is the respective thread in "ubuntuusers.de" > > http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/ > > (Although you might not speak german, the code provided will show > you, that the device is actually working with your driver). > > It would be nice, if you include this new device ID to the > sc92031-driver. > > Regards, > > Axel Köllhofer (aka Rain_Maker) Cc: rain_maker@root-forum.org Signed-off-by: Cesar Eduardo Barros Signed-off-by: David S. Miller --- drivers/net/sc92031.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/sc92031.c b/drivers/net/sc92031.c index 18821f217e19..e3156c97bb58 100644 --- a/drivers/net/sc92031.c +++ b/drivers/net/sc92031.c @@ -1593,6 +1593,7 @@ out: static struct pci_device_id sc92031_pci_device_id_table[] __devinitdata = { { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x2031) }, { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x8139) }, + { PCI_DEVICE(0x1088, 0x2031) }, { 0, } }; MODULE_DEVICE_TABLE(pci, sc92031_pci_device_id_table); -- cgit v1.2.3 From e2372902d84af3443d421a984d812ec87eeb0758 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:39 +0000 Subject: can: sja1000: remove duplicated includes Remove duplicated #include('s) in drivers/net/can/sja1000/sja1000.c Signed-off-by: Huang Weiyi Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/sja1000/sja1000.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index 571f133a8fec..08ebee79d8a6 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -63,7 +63,6 @@ #include #include #include -#include #include "sja1000.h" -- cgit v1.2.3 From b3d0df7ca35018ebbc24fd102ed7021cf593ba74 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:40 +0000 Subject: can: restart device even if dev_alloc_skb() fails If dev_alloc_skb() failed in can_restart(), the device was left behind in the bus-off state. This patch restarts the device nevertheless. Signed-off-by: Kurt Van Dijck Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 574daddc21bf..06083c32869a 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -346,7 +346,7 @@ void can_restart(unsigned long data) skb = dev_alloc_skb(sizeof(struct can_frame)); if (skb == NULL) { err = -ENOMEM; - goto out; + goto restart; } skb->dev = dev; skb->protocol = htons(ETH_P_CAN); @@ -361,13 +361,13 @@ void can_restart(unsigned long data) stats->rx_packets++; stats->rx_bytes += cf->can_dlc; +restart: dev_dbg(dev->dev.parent, "restarted\n"); priv->can_stats.restarts++; /* Now restart the device */ err = priv->do_set_mode(dev, CAN_MODE_START); -out: netif_carrier_on(dev); if (err) dev_err(dev->dev.parent, "Error %d during restart", err); -- cgit v1.2.3 From 1b0d92244ff2434a98272f6d2525da32fc230f19 Mon Sep 17 00:00:00 2001 From: Wolfgang Grandegger Date: Mon, 20 Jul 2009 04:06:41 +0000 Subject: can: switch carrier on if device was stopped while in bus-off state This patch fixes a problem when a device is stopped while in the bus-off state. Then the carrier remains off forever. Signed-off-by: Kurt Van Dijck Signed-off-by: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 06083c32869a..9e4283aff828 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -473,6 +473,10 @@ int open_candev(struct net_device *dev) return -EINVAL; } + /* Switch carrier on if device was stopped while in bus-off state */ + if (!netif_carrier_ok(dev)) + netif_carrier_on(dev); + setup_timer(&priv->restart_timer, can_restart, (unsigned long)dev); return 0; -- cgit v1.2.3 From c46a7aec556ffdbdb7357db0b05904b176cb3375 Mon Sep 17 00:00:00 2001 From: Kay Sievers Date: Mon, 20 Jul 2009 16:04:55 +0100 Subject: vc: create vcs(a) devices for consoles The buffer for the consoles are unconditionally allocated at con_init() time, which miss the creation of the vcs(a) devices. Since 2.6.30 (commit 4995f8ef9d3aac72745e12419d7fbaa8d01b1d81, 'vcs: hook sysfs devices into object lifetime instead of "binding"' to be exact) these devices are no longer created at open() and removed on close(), but controlled by the lifetime of the buffers. Reported-by: Gerardo Exequiel Pozzi Tested-by: Gerardo Exequiel Pozzi Cc: stable@kernel.org Signed-off-by: Kay Sievers Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/vc_screen.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/char/vc_screen.c b/drivers/char/vc_screen.c index d94d25c12aa8..c1791a63d99d 100644 --- a/drivers/char/vc_screen.c +++ b/drivers/char/vc_screen.c @@ -495,11 +495,15 @@ void vcs_remove_sysfs(int index) int __init vcs_init(void) { + unsigned int i; + if (register_chrdev(VCS_MAJOR, "vcs", &vcs_fops)) panic("unable to get major %d for vcs device", VCS_MAJOR); vc_class = class_create(THIS_MODULE, "vc"); device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 0), NULL, "vcs"); device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 128), NULL, "vcsa"); + for (i = 0; i < MIN_NR_CONSOLES; i++) + vcs_make_sysfs(i); return 0; } -- cgit v1.2.3 From 254702568da63ce6f5ad68e77d83b427da693654 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 20 Jul 2009 16:05:07 +0100 Subject: specialix.c: convert nested spin_lock_irqsave to spin_lock If spin_lock_irqsave is called twice in a row with the same second argument, the interrupt state at the point of the second call overwrites the value saved by the first call. Indeed, the second call does not need to save the interrupt state, so it is changed to a simple spin_lock. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ expression lock1,lock2; expression flags; @@ *spin_lock_irqsave(lock1,flags) ... when != flags *spin_lock_irqsave(lock2,flags) // Signed-off-by: Julia Lawall Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/specialix.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/char/specialix.c b/drivers/char/specialix.c index bfe4cdb2febb..268e17f9ec3f 100644 --- a/drivers/char/specialix.c +++ b/drivers/char/specialix.c @@ -1809,10 +1809,10 @@ static int sx_tiocmset(struct tty_struct *tty, struct file *file, if (clear & TIOCM_DTR) port->MSVR &= ~MSVR_DTR; } - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_CAR, port_No(port)); sx_out(bp, CD186x_MSVR, port->MSVR); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); spin_unlock_irqrestore(&port->lock, flags); func_exit(); return 0; @@ -1833,11 +1833,11 @@ static int sx_send_break(struct tty_struct *tty, int length) port->break_length = SPECIALIX_TPS / HZ * length; port->COR2 |= COR2_ETC; port->IER |= IER_TXRDY; - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_CAR, port_No(port)); sx_out(bp, CD186x_COR2, port->COR2); sx_out(bp, CD186x_IER, port->IER); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); spin_unlock_irqrestore(&port->lock, flags); sx_wait_CCR(bp); spin_lock_irqsave(&bp->lock, flags); @@ -2023,9 +2023,9 @@ static void sx_unthrottle(struct tty_struct *tty) if (sx_crtscts(tty)) port->MSVR |= MSVR_DTR; /* Else clause: see remark in "sx_throttle"... */ - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_CAR, port_No(port)); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); if (I_IXOFF(tty)) { spin_unlock_irqrestore(&port->lock, flags); sx_wait_CCR(bp); @@ -2035,9 +2035,9 @@ static void sx_unthrottle(struct tty_struct *tty) sx_wait_CCR(bp); spin_lock_irqsave(&port->lock, flags); } - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_MSVR, port->MSVR); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); spin_unlock_irqrestore(&port->lock, flags); func_exit(); @@ -2061,10 +2061,10 @@ static void sx_stop(struct tty_struct *tty) spin_lock_irqsave(&port->lock, flags); port->IER &= ~IER_TXRDY; - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_CAR, port_No(port)); sx_out(bp, CD186x_IER, port->IER); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); spin_unlock_irqrestore(&port->lock, flags); func_exit(); @@ -2089,10 +2089,10 @@ static void sx_start(struct tty_struct *tty) spin_lock_irqsave(&port->lock, flags); if (port->xmit_cnt && port->xmit_buf && !(port->IER & IER_TXRDY)) { port->IER |= IER_TXRDY; - spin_lock_irqsave(&bp->lock, flags); + spin_lock(&bp->lock); sx_out(bp, CD186x_CAR, port_No(port)); sx_out(bp, CD186x_IER, port->IER); - spin_unlock_irqrestore(&bp->lock, flags); + spin_unlock(&bp->lock); } spin_unlock_irqrestore(&port->lock, flags); -- cgit v1.2.3 From 23198fda7182969b619613a555f8645fdc3dc334 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 20 Jul 2009 16:05:27 +0100 Subject: tty: fix chars_in_buffers This function does not have an error return and returning an error is instead interpreted as having a lot of pending bytes. Reported by Jeff Harris who provided a list of some of the remaining offenders. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/hvc_console.c | 2 +- drivers/char/nozomi.c | 4 +--- drivers/char/pcmcia/ipwireless/tty.c | 4 ++-- drivers/isdn/gigaset/interface.c | 2 ++ drivers/usb/class/cdc-acm.c | 2 +- drivers/usb/serial/mos7720.c | 2 +- drivers/usb/serial/ti_usb_3410_5052.c | 4 ++-- 7 files changed, 10 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/char/hvc_console.c b/drivers/char/hvc_console.c index 94e7e3c8c05a..d97779ef72cb 100644 --- a/drivers/char/hvc_console.c +++ b/drivers/char/hvc_console.c @@ -552,7 +552,7 @@ static int hvc_chars_in_buffer(struct tty_struct *tty) struct hvc_struct *hp = tty->driver_data; if (!hp) - return -1; + return 0; return hp->n_outbuf; } diff --git a/drivers/char/nozomi.c b/drivers/char/nozomi.c index 280b41c507a7..ec58d8c387ff 100644 --- a/drivers/char/nozomi.c +++ b/drivers/char/nozomi.c @@ -1866,16 +1866,14 @@ static s32 ntty_chars_in_buffer(struct tty_struct *tty) { struct port *port = tty->driver_data; struct nozomi *dc = get_dc_by_tty(tty); - s32 rval; + s32 rval = 0; if (unlikely(!dc || !port)) { - rval = -ENODEV; goto exit_in_buffer; } if (unlikely(!port->port.count)) { dev_err(&dc->pdev->dev, "No tty open?\n"); - rval = -ENODEV; goto exit_in_buffer; } diff --git a/drivers/char/pcmcia/ipwireless/tty.c b/drivers/char/pcmcia/ipwireless/tty.c index 569f2f7743a7..674b3ab3587d 100644 --- a/drivers/char/pcmcia/ipwireless/tty.c +++ b/drivers/char/pcmcia/ipwireless/tty.c @@ -320,10 +320,10 @@ static int ipw_chars_in_buffer(struct tty_struct *linux_tty) struct ipw_tty *tty = linux_tty->driver_data; if (!tty) - return -ENODEV; + return 0; if (!tty->open_count) - return -EINVAL; + return 0; return tty->tx_bytes_queued; } diff --git a/drivers/isdn/gigaset/interface.c b/drivers/isdn/gigaset/interface.c index 1ebfcab74662..8ff7e35c7069 100644 --- a/drivers/isdn/gigaset/interface.c +++ b/drivers/isdn/gigaset/interface.c @@ -408,6 +408,8 @@ static int if_write_room(struct tty_struct *tty) return retval; } +/* FIXME: This function does not have error returns */ + static int if_chars_in_buffer(struct tty_struct *tty) { struct cardstate *cs; diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 5b15d9d8896b..e1f89416ef8c 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -750,7 +750,7 @@ static int acm_tty_chars_in_buffer(struct tty_struct *tty) { struct acm *acm = tty->driver_data; if (!ACM_READY(acm)) - return -EINVAL; + return 0; /* * This is inaccurate (overcounts), but it works. */ diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index bfc5ce000ef9..ccd4dd340d2c 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -521,7 +521,7 @@ static int mos7720_chars_in_buffer(struct tty_struct *tty) mos7720_port = usb_get_serial_port_data(port); if (mos7720_port == NULL) { dbg("%s:leaving ...........", __func__); - return -ENODEV; + return 0; } for (i = 0; i < NUM_URBS; ++i) { diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index 14971a926990..3bc609fe2242 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -727,7 +727,7 @@ static int ti_write_room(struct tty_struct *tty) dbg("%s - port %d", __func__, port->number); if (tport == NULL) - return -ENODEV; + return 0; spin_lock_irqsave(&tport->tp_lock, flags); room = ti_buf_space_avail(tport->tp_write_buf); @@ -748,7 +748,7 @@ static int ti_chars_in_buffer(struct tty_struct *tty) dbg("%s - port %d", __func__, port->number); if (tport == NULL) - return -ENODEV; + return 0; spin_lock_irqsave(&tport->tp_lock, flags); chars = ti_buf_data_avail(tport->tp_write_buf); -- cgit v1.2.3 From 6cdbf734493d6e8f5afc6f539b82897772809d43 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Sat, 18 Jul 2009 20:34:37 -0400 Subject: mvsdio: fix handling of partial word at the end of PIO transfer Standard data flow for MMC/SD/SDIO cards requires that the mvsdio controller be set for big endian operation. This is causing problems with buffers which length is not a multiple of 4 bytes as the last partial word doesn't get shifted all the way and stored properly in memory. Let's compensate for this. Signed-off-by: Nicolas Pitre CC: stable@kernel.org Signed-off-by: Linus Torvalds --- drivers/mmc/host/mvsdio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/mmc/host/mvsdio.c b/drivers/mmc/host/mvsdio.c index b56d72ff06e9..34e23489811a 100644 --- a/drivers/mmc/host/mvsdio.c +++ b/drivers/mmc/host/mvsdio.c @@ -384,7 +384,7 @@ static irqreturn_t mvsd_irq(int irq, void *dev) u16 val[2] = {0, 0}; val[0] = mvsd_read(MVSD_FIFO); val[1] = mvsd_read(MVSD_FIFO); - memcpy(p, &val, s); + memcpy(p, ((void *)&val) + 4 - s, s); s = 0; intr_status = mvsd_read(MVSD_NOR_INTR_STATUS); } @@ -423,7 +423,7 @@ static irqreturn_t mvsd_irq(int irq, void *dev) if (s < 4) { if (s && (intr_status & MVSD_NOR_TX_AVAIL)) { u16 val[2] = {0, 0}; - memcpy(&val, p, s); + memcpy(((void *)&val) + 4 - s, p, s); mvsd_write(MVSD_FIFO, val[0]); mvsd_write(MVSD_FIFO, val[1]); s = 0; -- cgit v1.2.3 From 032e46cbf5fb1d768d7dec5631c224e22b4be46f Mon Sep 17 00:00:00 2001 From: Jerone Young Date: Mon, 20 Jul 2009 22:14:59 -0700 Subject: Input: atkbd - add force relese key quirk for Soltech TA12 Netbooks based on the Soltech TA12 do not send a key release for volume keys causing Linux to think the key is constantly being pressed forever. Added quirk data for forced release keys. BugLink: https://bugs.launchpad.net//bugs/397499 Signed-off-by: Jerone Young Signed-off-by: Tim Gardner Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/atkbd.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'drivers') diff --git a/drivers/input/keyboard/atkbd.c b/drivers/input/keyboard/atkbd.c index 809a7ddbe3af..95fe0452dae4 100644 --- a/drivers/input/keyboard/atkbd.c +++ b/drivers/input/keyboard/atkbd.c @@ -908,6 +908,13 @@ static unsigned int atkbd_amilo_xi3650_forced_release_keys[] = { 0x67, 0xed, 0x90, 0xa2, 0x99, 0xa4, 0xae, 0xb0, -1U }; +/* + * Soltech TA12 system with broken key release on volume keys and mute key + */ +static unsigned int atkdb_soltech_ta12_forced_release_keys[] = { + 0xa0, 0xae, 0xb0, -1U +}; + /* * atkbd_set_keycode_table() initializes keyboard's keycode table * according to the selected scancode set @@ -1592,6 +1599,15 @@ static struct dmi_system_id atkbd_dmi_quirk_table[] __initdata = { .callback = atkbd_setup_forced_release, .driver_data = atkbd_amilo_xi3650_forced_release_keys, }, + { + .ident = "Soltech Corporation TA12", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Soltech Corporation"), + DMI_MATCH(DMI_PRODUCT_NAME, "TA12"), + }, + .callback = atkbd_setup_forced_release, + .driver_data = atkdb_soltech_ta12_forced_release_keys, + }, { } }; -- cgit v1.2.3 From 513a2396d8e8327aff1ce50bea3fb4f16ff3455b Mon Sep 17 00:00:00 2001 From: Zhu Yi Date: Thu, 9 Jul 2009 17:24:15 +0800 Subject: iwmc3200wifi: fix NULL pointer dereference in iwm_if_free The driver private data is now based on wiphy. So we should not touch the private data after wiphy_free() is called. The patch fixes the potential NULL pointer dereference by making the iwm_wdev_free() the last one on the interface removal path. Signed-off-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/netdev.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c index aaa20c6885c8..aea5ccf24ccf 100644 --- a/drivers/net/wireless/iwmc3200wifi/netdev.c +++ b/drivers/net/wireless/iwmc3200wifi/netdev.c @@ -151,8 +151,8 @@ void iwm_if_free(struct iwm_priv *iwm) return; free_netdev(iwm_to_ndev(iwm)); - iwm_wdev_free(iwm); iwm_priv_deinit(iwm); + iwm_wdev_free(iwm); } int iwm_if_add(struct iwm_priv *iwm) -- cgit v1.2.3 From 872ed1902f511a8947021c562f5728a5bf0640b5 Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Thu, 9 Jul 2009 10:33:37 -0700 Subject: iwlwifi: only show active power level via sysfs This changes the power_level file to adhere to the "one value per file" sysfs rule. The user will know which power level was requested as it will be the number just written to this file. It is thus not necessary to create a new sysfs file for this value. In addition it fixes a problem where powertop's parsing expects this value to be the first value in this file without any descriptions. Signed-off-by: Reinette Chatre cc: stable@kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-agn.c | 4 +--- drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 +--- 2 files changed, 2 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c index 6d1519e1f011..355f50ea7fef 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn.c @@ -2675,12 +2675,10 @@ static ssize_t show_power_level(struct device *d, struct device_attribute *attr, char *buf) { struct iwl_priv *priv = dev_get_drvdata(d); - int mode = priv->power_data.user_power_setting; int level = priv->power_data.power_mode; char *p = buf; - p += sprintf(p, "INDEX:%d\t", level); - p += sprintf(p, "USER:%d\n", mode); + p += sprintf(p, "%d\n", level); return p - buf + 1; } diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index cb9bd4c8f25e..956798f2c80c 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -3643,12 +3643,10 @@ static ssize_t show_power_level(struct device *d, struct device_attribute *attr, char *buf) { struct iwl_priv *priv = dev_get_drvdata(d); - int mode = priv->power_data.user_power_setting; int level = priv->power_data.power_mode; char *p = buf; - p += sprintf(p, "INDEX:%d\t", level); - p += sprintf(p, "USER:%d\n", mode); + p += sprintf(p, "%d\n", level); return p - buf + 1; } -- cgit v1.2.3 From 7b80ece41aea0b73283c6df5a8f25d40aa13135d Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Thu, 9 Jul 2009 10:33:39 -0700 Subject: iwlwifi: only update byte count table during aggregation The byte count table is only used for aggregation. Updating it in other cases caused fragmented frames to be dropped. This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004 Signed-off-by: Reinette Chatre Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 85ae7a62109c..9bbeec9427f0 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -872,7 +872,8 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) iwl_print_hex_dump(priv, IWL_DL_TX, (u8 *)tx_cmd->hdr, hdr_len); /* Set up entry for this TFD in Tx byte-count array */ - priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq, + if (info->flags & IEEE80211_TX_CTL_AMPDU) + priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq, le16_to_cpu(tx_cmd->len)); pci_dma_sync_single_for_device(priv->pci_dev, txcmd_phys, -- cgit v1.2.3 From 5d41635195c06fc3116ef3921fe85a9a3ea5ab20 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Mon, 13 Jul 2009 13:04:30 +0200 Subject: mac80211_hwsim: fix unregistration If you rmmod the module while associated, frames might be transmitted during unregistration -- which will crash if the hwsim%d interface is unregistered first, so only do that after all the virtual wiphys are gone. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/mac80211_hwsim.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index a111bda392e2..5bed8241f3cc 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -1167,8 +1167,8 @@ static void __exit exit_mac80211_hwsim(void) { printk(KERN_DEBUG "mac80211_hwsim: unregister radios\n"); - unregister_netdev(hwsim_mon); mac80211_hwsim_free(); + unregister_netdev(hwsim_mon); } -- cgit v1.2.3 From e603d9d824ff0eda98a65708a7e82112becf2dca Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Mon, 13 Jul 2009 13:25:58 +0200 Subject: mac80211_hwsim: fix use after free Once the "data" pointer is freed, we can't be iterating to the next item in the list any more so we need to use list_for_each_entry_safe with a temporary variable. Signed-off-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/mac80211_hwsim.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c index 5bed8241f3cc..7916ca3f84c8 100644 --- a/drivers/net/wireless/mac80211_hwsim.c +++ b/drivers/net/wireless/mac80211_hwsim.c @@ -709,7 +709,7 @@ static const struct ieee80211_ops mac80211_hwsim_ops = static void mac80211_hwsim_free(void) { struct list_head tmplist, *i, *tmp; - struct mac80211_hwsim_data *data; + struct mac80211_hwsim_data *data, *tmpdata; INIT_LIST_HEAD(&tmplist); @@ -718,7 +718,7 @@ static void mac80211_hwsim_free(void) list_move(i, &tmplist); spin_unlock_bh(&hwsim_radio_lock); - list_for_each_entry(data, &tmplist, list) { + list_for_each_entry_safe(data, tmpdata, &tmplist, list) { debugfs_remove(data->debugfs_group); debugfs_remove(data->debugfs_ps); debugfs_remove(data->debugfs); -- cgit v1.2.3 From 65b5a69860ed3bc4224368b804d381cd9cafa90a Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Mon, 13 Jul 2009 21:57:39 -0400 Subject: ath5k: temporarily disable crypto for AP mode Pavel Roskin reported some issues with using AP mode without nohwcrypt=1. Most likely this is similar to the problem fixed some time ago in ath9k by 3f53dd64f192450cb331c0fecfc26ca952fb242f, "ath9k: Fix hw crypto configuration for TKIP in AP mode." That only affects TKIP but it's easiest to just disable that and WEP too until we get a proper fix in. Signed-off-by: Bob Copeland Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath5k/base.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c index ea045151f953..029c1bc7468f 100644 --- a/drivers/net/wireless/ath/ath5k/base.c +++ b/drivers/net/wireless/ath/ath5k/base.c @@ -2970,6 +2970,9 @@ ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, if (modparam_nohwcrypt) return -EOPNOTSUPP; + if (sc->opmode == NL80211_IFTYPE_AP) + return -EOPNOTSUPP; + switch (key->alg) { case ALG_WEP: case ALG_TKIP: -- cgit v1.2.3 From 3da7429ce92abd79b14e2275a28be144ce2c3013 Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Tue, 14 Jul 2009 15:55:16 -0500 Subject: rtl8187: Fix for kernel oops when unloading with LEDs enabled MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel may oops when the module is unloaded as the workqueue for led_on was not being cancelled. This patch fixes the problem reported in http://marc.info/?l=linux-wireless&m=124742957615781&w=2. Reported-by: Gábor Stefanik Signed-off-by: Larry Finger Signed-off-by: John W. Linville --- drivers/net/wireless/rtl818x/rtl8187_leds.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/rtl818x/rtl8187_leds.c b/drivers/net/wireless/rtl818x/rtl8187_leds.c index b44253592243..cf9f899fe0e6 100644 --- a/drivers/net/wireless/rtl818x/rtl8187_leds.c +++ b/drivers/net/wireless/rtl818x/rtl8187_leds.c @@ -208,11 +208,12 @@ void rtl8187_leds_exit(struct ieee80211_hw *dev) { struct rtl8187_priv *priv = dev->priv; - rtl8187_unregister_led(&priv->led_tx); /* turn the LED off before exiting */ queue_delayed_work(dev->workqueue, &priv->led_off, 0); cancel_delayed_work_sync(&priv->led_off); + cancel_delayed_work_sync(&priv->led_on); rtl8187_unregister_led(&priv->led_rx); + rtl8187_unregister_led(&priv->led_tx); } #endif /* def CONFIG_RTL8187_LED */ -- cgit v1.2.3 From 7adfd5c71693b81e995283805b17aa4a2ee0ecd9 Mon Sep 17 00:00:00 2001 From: Andy Whitcroft Date: Thu, 16 Jul 2009 16:28:11 +0100 Subject: rt2x00: Fix chipset detection for rt2500usb The commit below changed the semantics of rt2x00_check_rev so that it no longer checked the bottom 4 bits of the rev were non-zero. During that conversion this part of the check was not propogated to the rt2500usb initialisation. commit 358623c22c9fd837b3b1b444377037f72553dc9f Author: Ivo van Doorn Date: Tue May 5 19:46:08 2009 +0200 rt2x00: Simplify rt2x00_check_rev Without this check rt73 devices are miss recognised as rt2500 devices and two drivers are loaded. Preventing the device being used. Reinstate this check. Signed-off-by: Andy Whitcroft Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2500usb.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/rt2x00/rt2500usb.c b/drivers/net/wireless/rt2x00/rt2500usb.c index 66daf68ff0ee..ce75426764a1 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.c +++ b/drivers/net/wireless/rt2x00/rt2500usb.c @@ -1550,7 +1550,9 @@ static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev) rt2500usb_register_read(rt2x00dev, MAC_CSR0, ®); rt2x00_set_chip(rt2x00dev, RT2570, value, reg); - if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0)) { + if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0) || + rt2x00_check_rev(&rt2x00dev->chip, 0x0000000f, 0)) { + ERROR(rt2x00dev, "Invalid RT chipset detected.\n"); return -ENODEV; } -- cgit v1.2.3 From c66284f2a421f6aebbafd56cb8b90b8e6a9cb2de Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 16 Jul 2009 10:17:35 -0700 Subject: ath9k: Tune ANI function processing on AP mode during ANI reset For AP mode we must tune ANI specially for 2 GHz and for 5 GHz. We mask in only the flags we want to toggle on ath9k_hw_ani_control() through the ah->ani_function bitmask, this will take care of ignoring changes during ANI reset which we were disabling before. Testedy-by: Steven Luo Cc: Bennyam Malavazi Cc: Jouni Malinen Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ani.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c index 1aeafb511ddd..aad259b4c197 100644 --- a/drivers/net/wireless/ath/ath9k/ani.c +++ b/drivers/net/wireless/ath/ath9k/ani.c @@ -478,6 +478,18 @@ void ath9k_ani_reset(struct ath_hw *ah) "Reset ANI state opmode %u\n", ah->opmode); ah->stats.ast_ani_reset++; + if (ah->opmode == NL80211_IFTYPE_AP) { + /* + * ath9k_hw_ani_control() will only process items set on + * ah->ani_function + */ + if (IS_CHAN_2GHZ(chan)) + ah->ani_function = (ATH9K_ANI_SPUR_IMMUNITY_LEVEL | + ATH9K_ANI_FIRSTEP_LEVEL); + else + ah->ani_function = 0; + } + ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL, 0); ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL, 0); ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, 0); -- cgit v1.2.3 From 25177476675142d3ebd60849e0cebc46bd1eef8e Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Sat, 11 Jul 2009 20:52:48 +0000 Subject: macsonic: move probe function to .devinit.text MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit A pointer to mac_sonic_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. Various other functions that are called by mac_sonic_probe need to move to .devinit.text, too. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: Uwe Kleine-König Tested-by: Finn Thain Signed-off-by: David S. Miller --- drivers/net/macsonic.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index acd143da161d..8f492c7b8093 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -179,7 +179,7 @@ static const struct net_device_ops macsonic_netdev_ops = { .ndo_set_mac_address = eth_mac_addr, }; -static int __init macsonic_init(struct net_device *dev) +static int __devinit macsonic_init(struct net_device *dev) { struct sonic_local* lp = netdev_priv(dev); @@ -223,7 +223,7 @@ static int __init macsonic_init(struct net_device *dev) return 0; } -static int __init mac_onboard_sonic_ethernet_addr(struct net_device *dev) +static int __devinit mac_onboard_sonic_ethernet_addr(struct net_device *dev) { struct sonic_local *lp = netdev_priv(dev); const int prom_addr = ONBOARD_SONIC_PROM_BASE; @@ -288,7 +288,7 @@ static int __init mac_onboard_sonic_ethernet_addr(struct net_device *dev) } else return 0; } -static int __init mac_onboard_sonic_probe(struct net_device *dev) +static int __devinit mac_onboard_sonic_probe(struct net_device *dev) { /* Bwahahaha */ static int once_is_more_than_enough; @@ -409,7 +409,7 @@ static int __init mac_onboard_sonic_probe(struct net_device *dev) return macsonic_init(dev); } -static int __init mac_nubus_sonic_ethernet_addr(struct net_device *dev, +static int __devinit mac_nubus_sonic_ethernet_addr(struct net_device *dev, unsigned long prom_addr, int id) { @@ -424,7 +424,7 @@ static int __init mac_nubus_sonic_ethernet_addr(struct net_device *dev, return 0; } -static int __init macsonic_ident(struct nubus_dev *ndev) +static int __devinit macsonic_ident(struct nubus_dev *ndev) { if (ndev->dr_hw == NUBUS_DRHW_ASANTE_LC && ndev->dr_sw == NUBUS_DRSW_SONIC_LC) @@ -449,7 +449,7 @@ static int __init macsonic_ident(struct nubus_dev *ndev) return -1; } -static int __init mac_nubus_sonic_probe(struct net_device *dev) +static int __devinit mac_nubus_sonic_probe(struct net_device *dev) { static int slots; struct nubus_dev* ndev = NULL; @@ -562,7 +562,7 @@ static int __init mac_nubus_sonic_probe(struct net_device *dev) return macsonic_init(dev); } -static int __init mac_sonic_probe(struct platform_device *pdev) +static int __devinit mac_sonic_probe(struct platform_device *pdev) { struct net_device *dev; struct sonic_local *lp; -- cgit v1.2.3 From 4564cba71637d3b4ea3730f5637b21a9eb3c8999 Mon Sep 17 00:00:00 2001 From: Finn Thain Date: Tue, 21 Jul 2009 12:21:49 -0700 Subject: macsonic, jazzsonic: fix oops on module unload Set the driver data before using it. Fixes an oops when doing rmmod. Signed-off-by: Finn Thain Signed-off-by: David S. Miller --- drivers/net/jazzsonic.c | 1 + drivers/net/macsonic.c | 1 + 2 files changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/jazzsonic.c b/drivers/net/jazzsonic.c index d12106b47bf2..2f286091394d 100644 --- a/drivers/net/jazzsonic.c +++ b/drivers/net/jazzsonic.c @@ -229,6 +229,7 @@ static int __init jazz_sonic_probe(struct platform_device *pdev) lp = netdev_priv(dev); lp->device = &pdev->dev; SET_NETDEV_DEV(dev, &pdev->dev); + platform_set_drvdata(pdev, dev); netdev_boot_setup_check(dev); diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index 8f492c7b8093..61eabcac734c 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -575,6 +575,7 @@ static int __devinit mac_sonic_probe(struct platform_device *pdev) lp = netdev_priv(dev); lp->device = &pdev->dev; SET_NETDEV_DEV(dev, &pdev->dev); + platform_set_drvdata(pdev, dev); /* This will catch fatal stuff like -ENOMEM as well as success */ err = mac_onboard_sonic_probe(dev); -- cgit v1.2.3 From 87cf65601e1709e57f7e28f0f7b3eb0a992c1782 Mon Sep 17 00:00:00 2001 From: Rémi Denis-Courmont Date: Tue, 21 Jul 2009 01:58:35 +0000 Subject: USB host CDC Phonet network interface driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Many Nokia handsets support a Phonet interface to the cellular modem via a vendor-specific USB interface. CDC Phonet follows the Communications Device Class model, with one control interface, and and a pair of inactive and active data alternative interface. The later has two bulk endpoint, one per direction. This was tested against Nokia E61, Nokia N95, and the existing Phonet gadget function for the Linux composite USB gadget framework. Signed-off-by: Rémi Denis-Courmont Signed-off-by: David S. Miller --- drivers/net/usb/Kconfig | 8 + drivers/net/usb/Makefile | 1 + drivers/net/usb/cdc-phonet.c | 461 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 470 insertions(+) create mode 100644 drivers/net/usb/cdc-phonet.c (limited to 'drivers') diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig index a906d3998131..c47237c2d638 100644 --- a/drivers/net/usb/Kconfig +++ b/drivers/net/usb/Kconfig @@ -369,4 +369,12 @@ config USB_NET_INT51X1 (Powerline Communications) solution with an Intellon INT51x1/INT5200 chip, like the "devolo dLan duo". +config USB_CDC_PHONET + tristate "CDC Phonet support" + depends on PHONET + help + Choose this option to support the Phonet interface to a Nokia + cellular modem, as found on most Nokia handsets with the + "PC suite" USB profile. + endmenu diff --git a/drivers/net/usb/Makefile b/drivers/net/usb/Makefile index b870b0b1cbe0..e17afb78f372 100644 --- a/drivers/net/usb/Makefile +++ b/drivers/net/usb/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o obj-$(CONFIG_USB_NET_MCS7830) += mcs7830.o obj-$(CONFIG_USB_USBNET) += usbnet.o obj-$(CONFIG_USB_NET_INT51X1) += int51x1.o +obj-$(CONFIG_USB_CDC_PHONET) += cdc-phonet.o diff --git a/drivers/net/usb/cdc-phonet.c b/drivers/net/usb/cdc-phonet.c new file mode 100644 index 000000000000..792af72da8ac --- /dev/null +++ b/drivers/net/usb/cdc-phonet.c @@ -0,0 +1,461 @@ +/* + * phonet.c -- USB CDC Phonet host driver + * + * Copyright (C) 2008-2009 Nokia Corporation. All rights reserved. + * + * Author: Rémi Denis-Courmont + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +#define PN_MEDIA_USB 0x1B + +static const unsigned rxq_size = 17; + +struct usbpn_dev { + struct net_device *dev; + + struct usb_interface *intf, *data_intf; + struct usb_device *usb; + unsigned int tx_pipe, rx_pipe; + u8 active_setting; + u8 disconnected; + + unsigned tx_queue; + spinlock_t tx_lock; + + spinlock_t rx_lock; + struct sk_buff *rx_skb; + struct urb *urbs[0]; +}; + +static void tx_complete(struct urb *req); +static void rx_complete(struct urb *req); + +/* + * Network device callbacks + */ +static int usbpn_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + struct urb *req = NULL; + unsigned long flags; + int err; + + if (skb->protocol != htons(ETH_P_PHONET)) + goto drop; + + req = usb_alloc_urb(0, GFP_ATOMIC); + if (!req) + goto drop; + usb_fill_bulk_urb(req, pnd->usb, pnd->tx_pipe, skb->data, skb->len, + tx_complete, skb); + req->transfer_flags = URB_ZERO_PACKET; + err = usb_submit_urb(req, GFP_ATOMIC); + if (err) { + usb_free_urb(req); + goto drop; + } + + spin_lock_irqsave(&pnd->tx_lock, flags); + pnd->tx_queue++; + if (pnd->tx_queue >= dev->tx_queue_len) + netif_stop_queue(dev); + spin_unlock_irqrestore(&pnd->tx_lock, flags); + return 0; + +drop: + dev_kfree_skb(skb); + dev->stats.tx_dropped++; + return 0; +} + +static void tx_complete(struct urb *req) +{ + struct sk_buff *skb = req->context; + struct net_device *dev = skb->dev; + struct usbpn_dev *pnd = netdev_priv(dev); + + switch (req->status) { + case 0: + dev->stats.tx_bytes += skb->len; + break; + + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + dev->stats.tx_aborted_errors++; + default: + dev->stats.tx_errors++; + dev_dbg(&dev->dev, "TX error (%d)\n", req->status); + } + dev->stats.tx_packets++; + + spin_lock(&pnd->tx_lock); + pnd->tx_queue--; + netif_wake_queue(dev); + spin_unlock(&pnd->tx_lock); + + dev_kfree_skb_any(skb); + usb_free_urb(req); +} + +static int rx_submit(struct usbpn_dev *pnd, struct urb *req, gfp_t gfp_flags) +{ + struct net_device *dev = pnd->dev; + struct page *page; + int err; + + page = __netdev_alloc_page(dev, gfp_flags); + if (!page) + return -ENOMEM; + + usb_fill_bulk_urb(req, pnd->usb, pnd->rx_pipe, page_address(page), + PAGE_SIZE, rx_complete, dev); + req->transfer_flags = 0; + err = usb_submit_urb(req, gfp_flags); + if (unlikely(err)) { + dev_dbg(&dev->dev, "RX submit error (%d)\n", err); + netdev_free_page(dev, page); + } + return err; +} + +static void rx_complete(struct urb *req) +{ + struct net_device *dev = req->context; + struct usbpn_dev *pnd = netdev_priv(dev); + struct page *page = virt_to_page(req->transfer_buffer); + struct sk_buff *skb; + unsigned long flags; + + switch (req->status) { + case 0: + spin_lock_irqsave(&pnd->rx_lock, flags); + skb = pnd->rx_skb; + if (!skb) { + skb = pnd->rx_skb = netdev_alloc_skb(dev, 12); + if (likely(skb)) { + /* Can't use pskb_pull() on page in IRQ */ + memcpy(skb_put(skb, 1), page_address(page), 1); + skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, + page, 1, req->actual_length); + page = NULL; + } + } else { + skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, + page, 0, req->actual_length); + page = NULL; + } + if (req->actual_length < PAGE_SIZE) + pnd->rx_skb = NULL; /* Last fragment */ + else + skb = NULL; + spin_unlock_irqrestore(&pnd->rx_lock, flags); + if (skb) { + skb->protocol = htons(ETH_P_PHONET); + skb_reset_mac_header(skb); + __skb_pull(skb, 1); + skb->dev = dev; + dev->stats.rx_packets++; + dev->stats.rx_bytes += skb->len; + + netif_rx(skb); + } + goto resubmit; + + case -ENOENT: + case -ECONNRESET: + case -ESHUTDOWN: + req = NULL; + break; + + case -EOVERFLOW: + dev->stats.rx_over_errors++; + dev_dbg(&dev->dev, "RX overflow\n"); + break; + + case -EILSEQ: + dev->stats.rx_crc_errors++; + break; + } + + dev->stats.rx_errors++; +resubmit: + if (page) + netdev_free_page(dev, page); + if (req) + rx_submit(pnd, req, GFP_ATOMIC); +} + +static int usbpn_close(struct net_device *dev); + +static int usbpn_open(struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + int err; + unsigned i; + unsigned num = pnd->data_intf->cur_altsetting->desc.bInterfaceNumber; + + err = usb_set_interface(pnd->usb, num, pnd->active_setting); + if (err) + return err; + + for (i = 0; i < rxq_size; i++) { + struct urb *req = usb_alloc_urb(0, GFP_KERNEL); + + if (!req || rx_submit(pnd, req, GFP_KERNEL)) { + usbpn_close(dev); + return -ENOMEM; + } + pnd->urbs[i] = req; + } + + netif_wake_queue(dev); + return 0; +} + +static int usbpn_close(struct net_device *dev) +{ + struct usbpn_dev *pnd = netdev_priv(dev); + unsigned i; + unsigned num = pnd->data_intf->cur_altsetting->desc.bInterfaceNumber; + + netif_stop_queue(dev); + + for (i = 0; i < rxq_size; i++) { + struct urb *req = pnd->urbs[i]; + + if (!req) + continue; + usb_kill_urb(req); + usb_free_urb(req); + pnd->urbs[i] = NULL; + } + + return usb_set_interface(pnd->usb, num, !pnd->active_setting); +} + +static int usbpn_set_mtu(struct net_device *dev, int new_mtu) +{ + if ((new_mtu < PHONET_MIN_MTU) || (new_mtu > PHONET_MAX_MTU)) + return -EINVAL; + + dev->mtu = new_mtu; + return 0; +} + +static const struct net_device_ops usbpn_ops = { + .ndo_open = usbpn_open, + .ndo_stop = usbpn_close, + .ndo_start_xmit = usbpn_xmit, + .ndo_change_mtu = usbpn_set_mtu, +}; + +static void usbpn_setup(struct net_device *dev) +{ + dev->features = 0; + dev->netdev_ops = &usbpn_ops, + dev->header_ops = &phonet_header_ops; + dev->type = ARPHRD_PHONET; + dev->flags = IFF_POINTOPOINT | IFF_NOARP; + dev->mtu = PHONET_MAX_MTU; + dev->hard_header_len = 1; + dev->dev_addr[0] = PN_MEDIA_USB; + dev->addr_len = 1; + dev->tx_queue_len = 3; + + dev->destructor = free_netdev; +} + +/* + * USB driver callbacks + */ +static struct usb_device_id usbpn_ids[] = { + { + .match_flags = USB_DEVICE_ID_MATCH_VENDOR + | USB_DEVICE_ID_MATCH_INT_CLASS + | USB_DEVICE_ID_MATCH_INT_SUBCLASS, + .idVendor = 0x0421, /* Nokia */ + .bInterfaceClass = USB_CLASS_COMM, + .bInterfaceSubClass = 0xFE, + }, + { }, +}; + +MODULE_DEVICE_TABLE(usb, usbpn_ids); + +static struct usb_driver usbpn_driver; + +int usbpn_probe(struct usb_interface *intf, const struct usb_device_id *id) +{ + static const char ifname[] = "usbpn%d"; + const struct usb_cdc_union_desc *union_header = NULL; + const struct usb_cdc_header_desc *phonet_header = NULL; + const struct usb_host_interface *data_desc; + struct usb_interface *data_intf; + struct usb_device *usbdev = interface_to_usbdev(intf); + struct net_device *dev; + struct usbpn_dev *pnd; + u8 *data; + int len, err; + + data = intf->altsetting->extra; + len = intf->altsetting->extralen; + while (len >= 3) { + u8 dlen = data[0]; + if (dlen < 3) + return -EINVAL; + + /* bDescriptorType */ + if (data[1] == USB_DT_CS_INTERFACE) { + /* bDescriptorSubType */ + switch (data[2]) { + case USB_CDC_UNION_TYPE: + if (union_header || dlen < 5) + break; + union_header = + (struct usb_cdc_union_desc *)data; + break; + case 0xAB: + if (phonet_header || dlen < 5) + break; + phonet_header = + (struct usb_cdc_header_desc *)data; + break; + } + } + data += dlen; + len -= dlen; + } + + if (!union_header || !phonet_header) + return -EINVAL; + + data_intf = usb_ifnum_to_if(usbdev, union_header->bSlaveInterface0); + if (data_intf == NULL) + return -ENODEV; + /* Data interface has one inactive and one active setting */ + if (data_intf->num_altsetting != 2) + return -EINVAL; + if (data_intf->altsetting[0].desc.bNumEndpoints == 0 + && data_intf->altsetting[1].desc.bNumEndpoints == 2) + data_desc = data_intf->altsetting + 1; + else + if (data_intf->altsetting[0].desc.bNumEndpoints == 2 + && data_intf->altsetting[1].desc.bNumEndpoints == 0) + data_desc = data_intf->altsetting; + else + return -EINVAL; + + dev = alloc_netdev(sizeof(*pnd) + sizeof(pnd->urbs[0]) * rxq_size, + ifname, usbpn_setup); + if (!dev) + return -ENOMEM; + + pnd = netdev_priv(dev); + SET_NETDEV_DEV(dev, &intf->dev); + netif_stop_queue(dev); + + pnd->dev = dev; + pnd->usb = usb_get_dev(usbdev); + pnd->intf = intf; + pnd->data_intf = data_intf; + spin_lock_init(&pnd->tx_lock); + spin_lock_init(&pnd->rx_lock); + /* Endpoints */ + if (usb_pipein(data_desc->endpoint[0].desc.bEndpointAddress)) { + pnd->rx_pipe = usb_rcvbulkpipe(usbdev, + data_desc->endpoint[0].desc.bEndpointAddress); + pnd->tx_pipe = usb_sndbulkpipe(usbdev, + data_desc->endpoint[1].desc.bEndpointAddress); + } else { + pnd->rx_pipe = usb_rcvbulkpipe(usbdev, + data_desc->endpoint[1].desc.bEndpointAddress); + pnd->tx_pipe = usb_sndbulkpipe(usbdev, + data_desc->endpoint[0].desc.bEndpointAddress); + } + pnd->active_setting = data_desc - data_intf->altsetting; + + err = usb_driver_claim_interface(&usbpn_driver, data_intf, pnd); + if (err) + goto out; + + /* Force inactive mode until the network device is brought UP */ + usb_set_interface(usbdev, union_header->bSlaveInterface0, + !pnd->active_setting); + usb_set_intfdata(intf, pnd); + + err = register_netdev(dev); + if (err) { + usb_driver_release_interface(&usbpn_driver, data_intf); + goto out; + } + + dev_dbg(&dev->dev, "USB CDC Phonet device found\n"); + return 0; + +out: + usb_set_intfdata(intf, NULL); + free_netdev(dev); + return err; +} + +static void usbpn_disconnect(struct usb_interface *intf) +{ + struct usbpn_dev *pnd = usb_get_intfdata(intf); + struct usb_device *usb = pnd->usb; + + if (pnd->disconnected) + return; + + pnd->disconnected = 1; + usb_driver_release_interface(&usbpn_driver, + (pnd->intf == intf) ? pnd->data_intf : pnd->intf); + unregister_netdev(pnd->dev); + usb_put_dev(usb); +} + +static struct usb_driver usbpn_driver = { + .name = "cdc_phonet", + .probe = usbpn_probe, + .disconnect = usbpn_disconnect, + .id_table = usbpn_ids, +}; + +static int __init usbpn_init(void) +{ + return usb_register(&usbpn_driver); +} + +static void __exit usbpn_exit(void) +{ + usb_deregister(&usbpn_driver); +} + +module_init(usbpn_init); +module_exit(usbpn_exit); + +MODULE_AUTHOR("Remi Denis-Courmont"); +MODULE_DESCRIPTION("USB CDC Phonet host interface"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From acb9c1b2f406d25c381de2b429f65706cc04d3b5 Mon Sep 17 00:00:00 2001 From: Evgeniy Polyakov Date: Tue, 21 Jul 2009 12:43:51 -0700 Subject: connector: maintainer/mail update. Signed-off-by: Evgeniy Polyakov Signed-off-by: David S. Miller --- Documentation/connector/cn_test.c | 4 ++-- Documentation/connector/ucon.c | 2 +- MAINTAINERS | 7 +++++++ drivers/connector/cn_queue.c | 2 +- drivers/connector/connector.c | 4 ++-- 5 files changed, 13 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/Documentation/connector/cn_test.c b/Documentation/connector/cn_test.c index f688eba87704..6a5be5d5c8e4 100644 --- a/Documentation/connector/cn_test.c +++ b/Documentation/connector/cn_test.c @@ -1,7 +1,7 @@ /* * cn_test.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify @@ -194,5 +194,5 @@ module_init(cn_test_init); module_exit(cn_test_fini); MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_AUTHOR("Evgeniy Polyakov "); MODULE_DESCRIPTION("Connector's test module"); diff --git a/Documentation/connector/ucon.c b/Documentation/connector/ucon.c index d738cde2a8d5..c5092ad0ce4b 100644 --- a/Documentation/connector/ucon.c +++ b/Documentation/connector/ucon.c @@ -1,7 +1,7 @@ /* * ucon.c * - * Copyright (c) 2004+ Evgeniy Polyakov + * Copyright (c) 2004+ Evgeniy Polyakov * * * This program is free software; you can redistribute it and/or modify diff --git a/MAINTAINERS b/MAINTAINERS index 6c6bb95acb15..88e8c00ede7f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1569,6 +1569,13 @@ S: Supported F: fs/configfs/ F: include/linux/configfs.h +CONNECTOR +P: Evgeniy Polyakov +M: zbr@ioremap.net +L: netdev@vger.kernel.org +S: Maintained +F: drivers/connector/ + CONTROL GROUPS (CGROUPS) P: Paul Menage M: menage@google.com diff --git a/drivers/connector/cn_queue.c b/drivers/connector/cn_queue.c index c769ef269fb5..408c2af25d50 100644 --- a/drivers/connector/cn_queue.c +++ b/drivers/connector/cn_queue.c @@ -1,7 +1,7 @@ /* * cn_queue.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify diff --git a/drivers/connector/connector.c b/drivers/connector/connector.c index fd336c5a9057..08b2500f21ec 100644 --- a/drivers/connector/connector.c +++ b/drivers/connector/connector.c @@ -1,7 +1,7 @@ /* * connector.c * - * 2004-2005 Copyright (c) Evgeniy Polyakov + * 2004+ Copyright (c) Evgeniy Polyakov * All rights reserved. * * This program is free software; you can redistribute it and/or modify @@ -33,7 +33,7 @@ #include MODULE_LICENSE("GPL"); -MODULE_AUTHOR("Evgeniy Polyakov "); +MODULE_AUTHOR("Evgeniy Polyakov "); MODULE_DESCRIPTION("Generic userspace <-> kernelspace connector."); static u32 cn_idx = CN_IDX_CONNECTOR; -- cgit v1.2.3 From ed5c8ef3bb2de277b7885072e0e981c41a022be5 Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Sun, 19 Jul 2009 09:48:28 +0100 Subject: acer-wmi: fix rfkill conversion Fix another polarity error introduced by the rfkill rewrite, this time in acer_rfkill_set(). Signed-off-by: Alan Jenkins Signed-off-by: John W. Linville --- drivers/platform/x86/acer-wmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index be2fd6f91639..fb45f5ee8df1 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -973,7 +973,7 @@ static int acer_rfkill_set(void *data, bool blocked) { acpi_status status; u32 cap = (unsigned long)data; - status = set_u32(!!blocked, cap); + status = set_u32(!blocked, cap); if (ACPI_FAILURE(status)) return -ENODEV; return 0; -- cgit v1.2.3 From bfa99bfdda1ce8a60f1f0fba7a04162a66d4ecfa Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 19 Jul 2009 21:26:13 +0200 Subject: p54spi: fix potential null deref in p54spi.c Fix a potential NULL dereference bug during error handling in p54spi_probe. This bug was discovered by smatch: (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/p54/p54spi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/p54/p54spi.c b/drivers/net/wireless/p54/p54spi.c index 83116baeb110..72c7dbd39d0a 100644 --- a/drivers/net/wireless/p54/p54spi.c +++ b/drivers/net/wireless/p54/p54spi.c @@ -635,7 +635,7 @@ static int __devinit p54spi_probe(struct spi_device *spi) hw = p54_init_common(sizeof(*priv)); if (!hw) { - dev_err(&priv->spi->dev, "could not alloc ieee80211_hw"); + dev_err(&spi->dev, "could not alloc ieee80211_hw"); return -ENOMEM; } -- cgit v1.2.3 From 5d2214ac5e7f72c9ae70b2444649e8d1d3e1086d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 20 Jul 2009 08:32:47 -0700 Subject: ath: add support for special 0x8000 regulatory domain Two users of ar9170 devices have now reported their cards have been programmed with a regulatory domain of 0x8000. This is not a valid regulatory domain as such these users were unable to use these devices. Since this doesn't seem to be a device EEPROM corruption we must treat it specially. It may have been possible the manufacturer intended to use 0x0 as the regulatory domain and that would ultimately yield to US but since we cannot get confirmationf or this we default this special case to one of our world regulatory domains, specifically 0x64. Reported-by: DavidFreeman on #linux-wireless Reported-by: Joerg Albert Cc: Christian Lamparter , Cc: Stephen Chen Cc: David Quan Cc: Tony Yang Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/regd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/regd.c b/drivers/net/wireless/ath/regd.c index eef370bd1211..bf3d25ba7be1 100644 --- a/drivers/net/wireless/ath/regd.c +++ b/drivers/net/wireless/ath/regd.c @@ -474,6 +474,21 @@ ath_regd_init_wiphy(struct ath_regulatory *reg, return 0; } +/* + * Some users have reported their EEPROM programmed with + * 0x8000 set, this is not a supported regulatory domain + * but since we have more than one user with it we need + * a solution for them. We default to 0x64, which is the + * default Atheros world regulatory domain. + */ +static void ath_regd_sanitize(struct ath_regulatory *reg) +{ + if (reg->current_rd != COUNTRY_ERD_FLAG) + return; + printk(KERN_DEBUG "ath: EEPROM regdomain sanitized\n"); + reg->current_rd = 0x64; +} + int ath_regd_init(struct ath_regulatory *reg, struct wiphy *wiphy, @@ -486,6 +501,8 @@ ath_regd_init(struct ath_regulatory *reg, if (!reg) return -EINVAL; + ath_regd_sanitize(reg); + printk(KERN_DEBUG "ath: EEPROM regdomain: 0x%0x\n", reg->current_rd); if (!ath_regd_is_eeprom_valid(reg)) { -- cgit v1.2.3 From 154839962a582b8eb661cde94ef3af0e03b374d7 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 16 Jul 2009 19:19:53 +0200 Subject: libertas: Fix problem with broken V4 firmware on CF8381 Firmware V4 on CF8381 reports region code shifted by 1 byte to left. The following patch checks for this and handles it properly. Signed-off-by: Marek Vasut Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/cmd.c | 8 +++++++- drivers/net/wireless/libertas/defs.h | 2 ++ 2 files changed, 9 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/cmd.c b/drivers/net/wireless/libertas/cmd.c index 01db705a38ec..685098148e10 100644 --- a/drivers/net/wireless/libertas/cmd.c +++ b/drivers/net/wireless/libertas/cmd.c @@ -135,8 +135,14 @@ int lbs_update_hw_spec(struct lbs_private *priv) /* Clamp region code to 8-bit since FW spec indicates that it should * only ever be 8-bit, even though the field size is 16-bit. Some firmware * returns non-zero high 8 bits here. + * + * Firmware version 4.0.102 used in CF8381 has region code shifted. We + * need to check for this problem and handle it properly. */ - priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF; + if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V4) + priv->regioncode = (le16_to_cpu(cmd.regioncode) >> 8) & 0xFF; + else + priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF; for (i = 0; i < MRVDRV_MAX_REGION_CODE; i++) { /* use the region code to search for the index */ diff --git a/drivers/net/wireless/libertas/defs.h b/drivers/net/wireless/libertas/defs.h index 48da157d6cda..72f3479a4d70 100644 --- a/drivers/net/wireless/libertas/defs.h +++ b/drivers/net/wireless/libertas/defs.h @@ -234,6 +234,8 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in /** Mesh enable bit in FW capability */ #define MESH_CAPINFO_ENABLE_MASK (1<<16) +/** FW definition from Marvell v4 */ +#define MRVL_FW_V4 (0x04) /** FW definition from Marvell v5 */ #define MRVL_FW_V5 (0x05) /** FW definition from Marvell v10 */ -- cgit v1.2.3 From 0021195c40326ac4702faf28c32accd91b331641 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 06:13:04 +0000 Subject: drivers/net: Move a dereference below a NULL test If the NULL test is necessary, then the dereferences should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i BUG_ON (E == NULL||...); + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/ibm_newemac/rgmii.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ibm_newemac/rgmii.c b/drivers/net/ibm_newemac/rgmii.c index 1d5379de6900..8d76cb89dbd6 100644 --- a/drivers/net/ibm_newemac/rgmii.c +++ b/drivers/net/ibm_newemac/rgmii.c @@ -188,11 +188,12 @@ void rgmii_put_mdio(struct of_device *ofdev, int input) void rgmii_detach(struct of_device *ofdev, int input) { struct rgmii_instance *dev = dev_get_drvdata(&ofdev->dev); - struct rgmii_regs __iomem *p = dev->base; - - mutex_lock(&dev->lock); + struct rgmii_regs __iomem *p; BUG_ON(!dev || dev->users == 0); + p = dev->base; + + mutex_lock(&dev->lock); RGMII_DBG(dev, "detach(%d)" NL, input); -- cgit v1.2.3 From 0376d5b25ef11e9b6450ebae20781a32d8985170 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 05:26:35 +0000 Subject: drivers/net: Move a dereference below a NULL test If the NULL test is necessary, then the dereference should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ type T; expression E,E1; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E=E1 when != i if (E == NULL||...) S + i = E->fld; // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/bnx2x_link.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index ed648acef7cf..2ee581a2cdec 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -4212,13 +4212,14 @@ static void bnx2x_turn_off_sf(struct bnx2x *bp, u8 port) u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, u8 *version, u16 len) { - struct bnx2x *bp = params->bp; + struct bnx2x *bp; u32 ext_phy_type = 0; u32 spirom_ver = 0; u8 status = 0 ; if (version == NULL || params == NULL) return -EINVAL; + bp = params->bp; spirom_ver = REG_RD(bp, params->shmem_base + offsetof(struct shmem_region, -- cgit v1.2.3 From 86669530d966ca21f4245b9990e7ae188d433d1e Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 06:09:25 +0000 Subject: drivers/net/mlx4: Adjust constant The values in the advertising field are typically ADVERTISED_xxx, not SUPPORTED_xxx. Both SUPPORTED_10000baseT_Full and ADVERTISED_1000baseT_Full have the same value. The semantic match that finds this problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ struct ethtool_cmd E; @@ *E.advertising = SUPPORTED_10000baseT_Full // Signed-off-by: Julia Lawall Signed-off-by: David S. Miller --- drivers/net/mlx4/en_ethtool.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/mlx4/en_ethtool.c b/drivers/net/mlx4/en_ethtool.c index 091f99052c91..86467b444ac6 100644 --- a/drivers/net/mlx4/en_ethtool.c +++ b/drivers/net/mlx4/en_ethtool.c @@ -220,7 +220,7 @@ static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) { cmd->autoneg = AUTONEG_DISABLE; cmd->supported = SUPPORTED_10000baseT_Full; - cmd->advertising = SUPPORTED_10000baseT_Full; + cmd->advertising = ADVERTISED_1000baseT_Full; if (netif_carrier_ok(dev)) { cmd->speed = SPEED_10000; cmd->duplex = DUPLEX_FULL; -- cgit v1.2.3 From bc146d23d1358af43f03793c3ad8c9f16bbcffcb Mon Sep 17 00:00:00 2001 From: Maxime Bizon Date: Thu, 16 Jul 2009 06:32:52 +0000 Subject: ide: fix memory leak when flush command is issued I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory leak after writing lots of data, the kmalloc-96 slab cache keeps growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush is never kfreed. Commit a09485df9cda49fbde2766c86eb18a9cae585162 ("ide: move request type specific code from ide_end_drive_cmd() to callers (v3)") and f505d49ffd25ed062e76ffd17568d3937fcd338c ("ide: fix barriers support") cause this regression, cmd->rq must now be set for ide_complete_cmd to honor the IDE_TFLAG_DYN flag. Signed-off-by: Maxime Bizon Acked-by: Bartlomiej Zolnierkiewicz Signed-off-by: David S. Miller --- drivers/ide/ide-disk.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c index 695181120cdb..7f878017b736 100644 --- a/drivers/ide/ide-disk.c +++ b/drivers/ide/ide-disk.c @@ -455,6 +455,7 @@ static void idedisk_prepare_flush(struct request_queue *q, struct request *rq) rq->cmd_type = REQ_TYPE_ATA_TASKFILE; rq->special = cmd; + cmd->rq = rq; } ide_devset_get(multcount, mult_count); -- cgit v1.2.3 From 2fc2111c2729462b99b6e37f39a48917054776f5 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Sun, 19 Jul 2009 09:15:19 +0000 Subject: ide-tape: Don't leak kernel stack information Don't leak kernel stack information through uninitialized structure members. Signed-off-by: Michael Buesch Acked-by: Borislav Petkov . Signed-off-by: David S. Miller --- drivers/ide/ide-tape.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c index 013dc595fab6..bc5fb12b913c 100644 --- a/drivers/ide/ide-tape.c +++ b/drivers/ide/ide-tape.c @@ -1064,6 +1064,7 @@ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, tape->best_dsc_rw_freq = config.dsc_rw_frequency; break; case 0x0350: + memset(&config, 0, sizeof(config)); config.dsc_rw_frequency = (int) tape->best_dsc_rw_freq; config.nr_stages = 1; if (copy_to_user(argp, &config, sizeof(config))) -- cgit v1.2.3 From a947a39d52f5b647a2fd5eca55d39e722a2fa90f Mon Sep 17 00:00:00 2001 From: Mike McCormack Date: Tue, 21 Jul 2009 20:57:56 -0700 Subject: sky2: Avoid races in sky2_down Reset rx chain before trying to drain it. Shut interrupts off last, incase there's something to report. Signed-off-by: Mike McCormack Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/sky2.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index ba768dfa59e0..3550c5dcd93c 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1818,12 +1818,6 @@ static int sky2_down(struct net_device *dev) if (netif_msg_ifdown(sky2)) printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); - /* Disable port IRQ */ - imask = sky2_read32(hw, B0_IMSK); - imask &= ~portirq_msk[port]; - sky2_write32(hw, B0_IMSK, imask); - sky2_read32(hw, B0_IMSK); - /* Force flow control off */ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); @@ -1863,8 +1857,6 @@ static int sky2_down(struct net_device *dev) sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); - sky2_rx_stop(sky2); - sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); @@ -1874,6 +1866,14 @@ static int sky2_down(struct net_device *dev) sky2_write32(hw, STAT_ISR_TIMER_CNT, 0); sky2_read8(hw, STAT_ISR_TIMER_CTRL); + sky2_rx_stop(sky2); + + /* Disable port IRQ */ + imask = sky2_read32(hw, B0_IMSK); + imask &= ~portirq_msk[port]; + sky2_write32(hw, B0_IMSK, imask); + sky2_read32(hw, B0_IMSK); + synchronize_irq(hw->pdev->irq); napi_synchronize(&hw->napi); -- cgit v1.2.3 From 3730793d457fed79a6d49bae72996d458c8e4f2d Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Wed, 22 Jul 2009 08:49:22 -0700 Subject: fbmon: work around compiler bug in gcc-2.4.2 There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent he loop counter is of type 'unsigned char' and it should count to 128. The compiler will incorrectly decide that a trivial loop like this: unsigned char i, ... for (i = 0; i < 128; i++) { .. is endless, and will compile it to a single instruction that just branches to itself. This was triggered by the addition of '-fno-strict-overflow', and we could play games with compiler versions and go back to '-fwrapv' instead, but the trivial way to avoid it is to just make the loop induction variable be an 'int' instead. Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure for digging through assembler differences and finding it. Reported-and-tested-by: Krzysztof Oledzki Found-by: Troy Moure Gcc-bug-acked-by: Ian Lance Taylor Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- drivers/video/fbmon.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/video/fbmon.c b/drivers/video/fbmon.c index 5c1a2c01778f..9ae9cd32bd06 100644 --- a/drivers/video/fbmon.c +++ b/drivers/video/fbmon.c @@ -256,8 +256,8 @@ static void fix_edid(unsigned char *edid, int fix) static int edid_checksum(unsigned char *edid) { - unsigned char i, csum = 0, all_null = 0; - int err = 0, fix = check_edid(edid); + unsigned char csum = 0, all_null = 0; + int i, err = 0, fix = check_edid(edid); if (fix) fix_edid(edid, fix); -- cgit v1.2.3 From 24c30dbbcdda9aeccb23b4eecb6bb8e538742ea4 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:31 +0000 Subject: of/mdio: Add support function for Ethernet fixed-link property Fixed-link support is broken for the ucc_eth, gianfar, and fs_enet device drivers. The "OF MDIO rework" patches removed most of the support. Instead of re-adding fixed-link stuff to the drivers, this patch adds a support function for parsing the fixed-link property and obtaining a dummy phy to match. Note: the dummy phy handling in arch/powerpc is a bit of a hack and needs to be reworked. This function is being added now to solve the regression in the Ethernet drivers, but it should be considered a temporary measure until the fixed link handling can be reworked. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/of/of_mdio.c | 42 ++++++++++++++++++++++++++++++++++++++++++ include/linux/of_mdio.h | 3 +++ 2 files changed, 45 insertions(+) (limited to 'drivers') diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c index aee967d7f760..bacaa536fd51 100644 --- a/drivers/of/of_mdio.c +++ b/drivers/of/of_mdio.c @@ -9,6 +9,10 @@ * out of the OpenFirmware device tree and using it to populate an mii_bus. */ +#include +#include +#include +#include #include #include #include @@ -137,3 +141,41 @@ struct phy_device *of_phy_connect(struct net_device *dev, return phy_connect_direct(dev, phy, hndlr, flags, iface) ? NULL : phy; } EXPORT_SYMBOL(of_phy_connect); + +/** + * of_phy_connect_fixed_link - Parse fixed-link property and return a dummy phy + * @dev: pointer to net_device claiming the phy + * @hndlr: Link state callback for the network device + * @iface: PHY data interface type + * + * This function is a temporary stop-gap and will be removed soon. It is + * only to support the fs_enet, ucc_geth and gianfar Ethernet drivers. Do + * not call this function from new drivers. + */ +struct phy_device *of_phy_connect_fixed_link(struct net_device *dev, + void (*hndlr)(struct net_device *), + phy_interface_t iface) +{ + struct device_node *net_np; + char bus_id[MII_BUS_ID_SIZE + 3]; + struct phy_device *phy; + const u32 *phy_id; + int sz; + + if (!dev->dev.parent) + return NULL; + + net_np = dev_archdata_get_node(&dev->dev.parent->archdata); + if (!net_np) + return NULL; + + phy_id = of_get_property(net_np, "fixed-link", &sz); + if (!phy_id || sz < sizeof(*phy_id)) + return NULL; + + sprintf(bus_id, PHY_ID_FMT, "0", phy_id[0]); + + phy = phy_connect(dev, bus_id, hndlr, 0, iface); + return IS_ERR(phy) ? NULL : phy; +} +EXPORT_SYMBOL(of_phy_connect_fixed_link); diff --git a/include/linux/of_mdio.h b/include/linux/of_mdio.h index c9663c690303..53b94e025c7c 100644 --- a/include/linux/of_mdio.h +++ b/include/linux/of_mdio.h @@ -18,5 +18,8 @@ extern struct phy_device *of_phy_connect(struct net_device *dev, struct device_node *phy_np, void (*hndlr)(struct net_device *), u32 flags, phy_interface_t iface); +extern struct phy_device *of_phy_connect_fixed_link(struct net_device *dev, + void (*hndlr)(struct net_device *), + phy_interface_t iface); #endif /* __LINUX_OF_MDIO_H */ -- cgit v1.2.3 From eedbc705f9a094560b8d08c58b6787a5420a76a1 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:36 +0000 Subject: fs_enet: Revive fixed link support Since commit aa73832c5a80d6c52c69b18af858d88fa595dd3c ("Rework fs_enet driver to use of_mdio infrastructure") the fixed-link support is broken in the fs_enet driver. This patch fixes the support by removing a check for phy_node, and adding a call to of_phy_connect_fixed_link(). Also set netdev parent device via SET_NETDEV_DEV() call, this is needed so that OF MDIO core could find a node pointer for a device. Plus, fix "if (IS_ERR(phydev))" check, in case of errors, of_phy_connect() returns NULL, not ERR_PTR as phy_connect(). Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/fs_enet/fs_enet-main.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/net/fs_enet/fs_enet-main.c b/drivers/net/fs_enet/fs_enet-main.c index b892c3ad9a74..2bc2d2b20644 100644 --- a/drivers/net/fs_enet/fs_enet-main.c +++ b/drivers/net/fs_enet/fs_enet-main.c @@ -754,17 +754,16 @@ static int fs_init_phy(struct net_device *dev) fep->oldlink = 0; fep->oldspeed = 0; fep->oldduplex = -1; - if(fep->fpi->phy_node) - phydev = of_phy_connect(dev, fep->fpi->phy_node, - &fs_adjust_link, 0, - PHY_INTERFACE_MODE_MII); - else { - printk("No phy bus ID specified in BSP code\n"); - return -EINVAL; + + phydev = of_phy_connect(dev, fep->fpi->phy_node, &fs_adjust_link, 0, + PHY_INTERFACE_MODE_MII); + if (!phydev) { + phydev = of_phy_connect_fixed_link(dev, &fs_adjust_link, + PHY_INTERFACE_MODE_MII); } - if (IS_ERR(phydev)) { - printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); - return PTR_ERR(phydev); + if (!phydev) { + dev_err(&dev->dev, "Could not attach to PHY\n"); + return -ENODEV; } fep->phydev = phydev; @@ -1005,6 +1004,7 @@ static int __devinit fs_enet_probe(struct of_device *ofdev, goto out_free_fpi; } + SET_NETDEV_DEV(ndev, &ofdev->dev); dev_set_drvdata(&ofdev->dev, ndev); fep = netdev_priv(ndev); -- cgit v1.2.3 From 1db780f8c7d361fe1b7d29b9dc849b97955ae944 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:42 +0000 Subject: gianfar: Revive fixed link support Since commit fe192a49118f5b1272317d60c7930ece4e13ae49 ("Rework gianfar driver to use of_mdio infrastructure") the fixed-link support is broken, the driver oopses at init_phy(): Unable to handle kernel paging request for data at address 0x000000e4 Faulting instruction address: 0xc01cf298 Oops: Kernel access of bad area, sig: 11 [#1] [...] NIP [c01cf298] init_phy+0x80/0xdc LR [c01cf250] init_phy+0x38/0xdc Call Trace: [cf81fe80] [c01d1cf8] gfar_enet_open+0x6c/0x19c [cf81fea0] [c024494c] dev_open+0xfc/0x134 [cf81fec0] [c0242edc] dev_change_flags+0x84/0x1ac [cf81fee0] [c0399ee0] ic_open_devs+0x168/0x2d8 [cf81ff20] [c039b2e8] ip_auto_config+0x90/0x2a4 [cf81ff60] [c0003884] do_one_initcall+0x34/0x1a8 This patch fixes the oops, and removes phy_node checks, and adds a call to of_phy_connect_fixed_link() if a phy isn't attached.. Also, remove an old fixed-link code that we don't use any longer. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/gianfar.c | 24 ++++++++---------------- 1 file changed, 8 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 43d813ed9f45..f8ffcbf0bc39 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -264,15 +264,6 @@ static int gfar_of_init(struct net_device *dev) priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET; priv->phy_node = of_parse_phandle(np, "phy-handle", 0); - if (!priv->phy_node) { - u32 *fixed_link; - - fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL); - if (!fixed_link) { - err = -ENODEV; - goto err_out; - } - } /* Find the TBI PHY. If it's not there, we don't support SGMII */ priv->tbi_node = of_parse_phandle(np, "tbi-handle", 0); @@ -659,13 +650,14 @@ static int init_phy(struct net_device *dev) interface = gfar_get_interface(dev); - if (priv->phy_node) { - priv->phydev = of_phy_connect(dev, priv->phy_node, &adjust_link, - 0, interface); - if (!priv->phydev) { - dev_err(&dev->dev, "error: Could not attach to PHY\n"); - return -ENODEV; - } + priv->phydev = of_phy_connect(dev, priv->phy_node, &adjust_link, 0, + interface); + if (!priv->phydev) + priv->phydev = of_phy_connect_fixed_link(dev, &adjust_link, + interface); + if (!priv->phydev) { + dev_err(&dev->dev, "could not attach to PHY\n"); + return -ENODEV; } if (interface == PHY_INTERFACE_MODE_SGMII) -- cgit v1.2.3 From 3104a6ff67e484e4dc84822b4ed0396e85bb9fb9 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 16 Jul 2009 21:31:47 +0000 Subject: ucc_geth: Revive fixed link support Since commit 0b9da337dca972e7a4144e298ec3adb8f244d4a4 ("Rework ucc_geth driver to use of_mdio infrastructure") the fixed-link support is broken. This patch fixes the support by removing !ug_info->phy_node check, and adds a call to of_phy_connect_fixed_link() if a phy is not attached to the MAC. Also, remove an old fixed-link code that we don't use any longer. Signed-off-by: Anton Vorontsov Signed-off-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/ucc_geth.c | 23 +++++++---------------- 1 file changed, 7 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 40c6eba775ce..3b957e6412ee 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -1590,13 +1590,13 @@ static int init_phy(struct net_device *dev) priv->oldspeed = 0; priv->oldduplex = -1; - if (!ug_info->phy_node) - return 0; - phydev = of_phy_connect(dev, ug_info->phy_node, &adjust_link, 0, priv->phy_interface); + if (!phydev) + phydev = of_phy_connect_fixed_link(dev, &adjust_link, + priv->phy_interface); if (!phydev) { - printk("%s: Could not attach to PHY\n", dev->name); + dev_err(&dev->dev, "Could not attach to PHY\n"); return -ENODEV; } @@ -3608,9 +3608,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma struct ucc_geth_private *ugeth = NULL; struct ucc_geth_info *ug_info; struct resource res; - struct device_node *phy; int err, ucc_num, max_speed = 0; - const u32 *fixed_link; const unsigned int *prop; const char *sprop; const void *mac_addr; @@ -3708,15 +3706,8 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma ug_info->uf_info.regs = res.start; ug_info->uf_info.irq = irq_of_parse_and_map(np, 0); - fixed_link = of_get_property(np, "fixed-link", NULL); - if (fixed_link) { - phy = NULL; - } else { - phy = of_parse_phandle(np, "phy-handle", 0); - if (phy == NULL) - return -ENODEV; - } - ug_info->phy_node = phy; + + ug_info->phy_node = of_parse_phandle(np, "phy-handle", 0); /* Find the TBI PHY node. If it's not there, we don't support SGMII */ ug_info->tbi_node = of_parse_phandle(np, "tbi-handle", 0); @@ -3725,7 +3716,7 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma prop = of_get_property(np, "phy-connection-type", NULL); if (!prop) { /* handle interface property present in old trees */ - prop = of_get_property(phy, "interface", NULL); + prop = of_get_property(ug_info->phy_node, "interface", NULL); if (prop != NULL) { phy_interface = enet_to_phy_interface[*prop]; max_speed = enet_to_speed[*prop]; -- cgit v1.2.3 From fa77406aee9d33f35c7202dcd83436feb12d9fc3 Mon Sep 17 00:00:00 2001 From: Ajit Khaparde Date: Wed, 22 Jul 2009 09:28:55 -0700 Subject: be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly. This patch fixes a bug in the non-lro path. Wrong size of received packet was being passed for updating receive statistics. This patch is against the net-2.6 git. Signed-off-by: Ajit Khaparde Signed-off-by: David S. Miller --- drivers/net/benet/be_main.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index c43f6a119295..dea3155688bb 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -667,7 +667,7 @@ static void skb_fill_rx_data(struct be_adapter *adapter, struct be_queue_info *rxq = &adapter->rx_obj.q; struct be_rx_page_info *page_info; u16 rxq_idx, i, num_rcvd, j; - u32 pktsize, hdr_len, curr_frag_len; + u32 pktsize, hdr_len, curr_frag_len, size; u8 *start; rxq_idx = AMAP_GET_BITS(struct amap_eth_rx_compl, fragndx, rxcp); @@ -708,12 +708,13 @@ static void skb_fill_rx_data(struct be_adapter *adapter, } /* More frags present for this completion */ - pktsize -= curr_frag_len; /* account for above copied frag */ + size = pktsize; for (i = 1, j = 0; i < num_rcvd; i++) { + size -= curr_frag_len; index_inc(&rxq_idx, rxq->len); page_info = get_rx_page_info(adapter, rxq_idx); - curr_frag_len = min(pktsize, rx_frag_size); + curr_frag_len = min(size, rx_frag_size); /* Coalesce all frags from the same physical page in one slot */ if (page_info->page_offset == 0) { @@ -731,7 +732,6 @@ static void skb_fill_rx_data(struct be_adapter *adapter, skb_shinfo(skb)->frags[j].size += curr_frag_len; skb->len += curr_frag_len; skb->data_len += curr_frag_len; - pktsize -= curr_frag_len; memset(page_info, 0, sizeof(*page_info)); } -- cgit v1.2.3 From de72e5de062e48a992d6cafe2291a82fe498d641 Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Wed, 22 Jul 2009 01:16:51 +0000 Subject: net: KS8851 needs to depend on MII fix this build error when CONFIG_MII is not set drivers/net/ks8851.c:999: undefined reference to `generic_mii_ioctl' drivers/net/ks8851.c:1050: undefined reference to `mii_link_ok' drivers/net/ks8851.c:1056: undefined reference to `mii_nway_restart' drivers/net/ks8851.c:1044: undefined reference to `mii_ethtool_sset' drivers/net/ks8851.c:1038: undefined reference to `mii_ethtool_gset' Signed-off-by: Alexander Beregalov Acked-by: Ben Dooks --- drivers/net/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index b5a7513df4eb..5f6509a5f640 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1732,6 +1732,7 @@ config KS8842 config KS8851 tristate "Micrel KS8851 SPI" depends on SPI + select MII help SPI driver for Micrel KS8851 SPI attached network chip. -- cgit v1.2.3 From 7b55a4a3f761db7daba1ac526ef60f64f5c53689 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 22 Jul 2009 02:58:55 +0000 Subject: skge: Enable WoL by default if supported If skge hardware is capable of waking up the system from sleep, enable magic packet WoL during driver initialisation. This makes WoL work without calling 'ethtool -s ethX wol g' for each adapter. Signed-off-by: Rafael J. Wysocki Tested-by: Michael Guntsche Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/skge.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 60d502eef4fc..543af2044f40 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -3854,8 +3854,10 @@ static struct net_device *skge_devinit(struct skge_hw *hw, int port, skge->speed = -1; skge->advertising = skge_supported_modes(hw); - if (device_may_wakeup(&hw->pdev->dev)) + if (device_can_wakeup(&hw->pdev->dev)) { skge->wol = wol_supported(hw) & WAKE_MAGIC; + device_set_wakeup_enable(&hw->pdev->dev, skge->wol); + } hw->dev[port] = dev; -- cgit v1.2.3 From 78a9c9c97455d0f8d2d2098b2252eb4bf65be799 Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Tue, 21 Jul 2009 10:11:39 +0000 Subject: register at91_ether using platform_driver_probe MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit at91ether_probe lives in .init.text, so using platform_driver_register to register it is wrong because binding a device after the init memory is discarded (e.g. via sysfs) results in an oops. As requested by David Brownell platform_driver_probe is used instead of moving the probe function to .devinit.text as proposed initially. This saves some memory, but devices registered after the driver is probed are not bound (probably there are none) and binding via sysfs isn't possible. Signed-off-by: Uwe Kleine-König Acked-by: David Brownell Acked-by: Andrew Victor Signed-off-by: David S. Miller --- drivers/net/arm/at91_ether.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c index 2e7419a61191..5041d10bae9d 100644 --- a/drivers/net/arm/at91_ether.c +++ b/drivers/net/arm/at91_ether.c @@ -1228,7 +1228,6 @@ static int at91ether_resume(struct platform_device *pdev) #endif static struct platform_driver at91ether_driver = { - .probe = at91ether_probe, .remove = __devexit_p(at91ether_remove), .suspend = at91ether_suspend, .resume = at91ether_resume, @@ -1240,7 +1239,7 @@ static struct platform_driver at91ether_driver = { static int __init at91ether_init(void) { - return platform_driver_register(&at91ether_driver); + return platform_driver_probe(&at91ether_driver, at91ether_probe); } static void __exit at91ether_exit(void) -- cgit v1.2.3 From 2ded9e2747d0a390d281bb5b16ff7f640ec85f78 Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Thu, 16 Jul 2009 17:23:09 +0800 Subject: drm/i915: hdmi detection according by reading edid According to investigations from windows team ,hw team, and our test results on all 4x platofrms available (gm45, g45b, q45, g45a, g45c, g41a, and g41), we find currently Hot plug live status and Hot plug interrupt detection are not reliable, sometime the results from the two approaches are contradicts. So we chose edid detection for hdmi output. Signed-off-by: Ma Ling Reviewed-by: Ian Romanick Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_hdmi.c | 64 +++------------------------------------ 1 file changed, 4 insertions(+), 60 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c index 9e30daae37dc..1842290cded3 100644 --- a/drivers/gpu/drm/i915/intel_hdmi.c +++ b/drivers/gpu/drm/i915/intel_hdmi.c @@ -130,16 +130,17 @@ static bool intel_hdmi_mode_fixup(struct drm_encoder *encoder, } static enum drm_connector_status -intel_hdmi_edid_detect(struct drm_connector *connector) +intel_hdmi_detect(struct drm_connector *connector) { struct intel_output *intel_output = to_intel_output(connector); struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; struct edid *edid = NULL; enum drm_connector_status status = connector_status_disconnected; + hdmi_priv->has_hdmi_sink = false; edid = drm_get_edid(&intel_output->base, intel_output->ddc_bus); - hdmi_priv->has_hdmi_sink = false; + if (edid) { if (edid->input & DRM_EDID_INPUT_DIGITAL) { status = connector_status_connected; @@ -148,65 +149,8 @@ intel_hdmi_edid_detect(struct drm_connector *connector) intel_output->base.display_info.raw_edid = NULL; kfree(edid); } - return status; -} - -static enum drm_connector_status -igdng_hdmi_detect(struct drm_connector *connector) -{ - struct intel_output *intel_output = to_intel_output(connector); - struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; - - /* FIXME hotplug detect */ - - hdmi_priv->has_hdmi_sink = false; - return intel_hdmi_edid_detect(connector); -} -static enum drm_connector_status -intel_hdmi_detect(struct drm_connector *connector) -{ - struct drm_device *dev = connector->dev; - struct drm_i915_private *dev_priv = dev->dev_private; - struct intel_output *intel_output = to_intel_output(connector); - struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv; - u32 temp, bit; - - if (IS_IGDNG(dev)) - return igdng_hdmi_detect(connector); - - temp = I915_READ(PORT_HOTPLUG_EN); - - switch (hdmi_priv->sdvox_reg) { - case SDVOB: - temp |= HDMIB_HOTPLUG_INT_EN; - break; - case SDVOC: - temp |= HDMIC_HOTPLUG_INT_EN; - break; - default: - return connector_status_unknown; - } - - I915_WRITE(PORT_HOTPLUG_EN, temp); - - POSTING_READ(PORT_HOTPLUG_EN); - - switch (hdmi_priv->sdvox_reg) { - case SDVOB: - bit = HDMIB_HOTPLUG_INT_STATUS; - break; - case SDVOC: - bit = HDMIC_HOTPLUG_INT_STATUS; - break; - default: - return connector_status_unknown; - } - - if ((I915_READ(PORT_HOTPLUG_STAT) & bit) != 0) - return intel_hdmi_edid_detect(connector); - else - return connector_status_disconnected; + return status; } static int intel_hdmi_get_modes(struct drm_connector *connector) -- cgit v1.2.3 From e3d433040ee6077e33d4ad22e2f60a38b085786d Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:20 -0700 Subject: drivers/dma/fsldma.c: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/fsldma.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c index 6e60c77a145c..ef87a8984145 100644 --- a/drivers/dma/fsldma.c +++ b/drivers/dma/fsldma.c @@ -142,7 +142,7 @@ static int dma_is_idle(struct fsl_dma_chan *fsl_chan) static void dma_start(struct fsl_dma_chan *fsl_chan) { - u32 mr_set = 0;; + u32 mr_set = 0; if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) { DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32); -- cgit v1.2.3 From c019894efc9c9ba5939948caa78c133b1ec8ae63 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:21 -0700 Subject: drivers/dma: Remove unnecessary semicolons Signed-off-by: Joe Perches Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 2 +- drivers/dma/mv_xor.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index fb7da5141e96..cec1ec0b7d00 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -114,7 +114,7 @@ static void dmatest_init_srcs(u8 **bufs, unsigned int start, unsigned int len) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); for ( ; i < start + len; i++) buf[i] = PATTERN_SRC | PATTERN_COPY - | (~i & PATTERN_COUNT_MASK);; + | (~i & PATTERN_COUNT_MASK); for ( ; i < test_buf_size; i++) buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK); buf++; diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c index ddab94f51224..3f23eabe09f2 100644 --- a/drivers/dma/mv_xor.c +++ b/drivers/dma/mv_xor.c @@ -1176,7 +1176,7 @@ static int __devinit mv_xor_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMSET, dma_dev->cap_mask)) dma_dev->device_prep_dma_memset = mv_xor_prep_dma_memset; if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { - dma_dev->max_xor = 8; ; + dma_dev->max_xor = 8; dma_dev->device_prep_dma_xor = mv_xor_prep_dma_xor; } -- cgit v1.2.3 From 0a2ff57d6fba92842272889b4bca447344cd9d36 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:26:51 +0200 Subject: dmaengine: dmatest: add a maximum number of test iterations The dmatest usually waits for the killing of its kthreads to stop running tests. This patch adds a parameter that sets a maximum number of test iterations. This feature is quite interesting for debugging when you set a lot of traces in your dmaengine controller driver. Signed-off-by: Nicolas Ferre Cc: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index cec1ec0b7d00..2d973d60e7b9 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -38,6 +38,11 @@ module_param(max_channels, uint, S_IRUGO); MODULE_PARM_DESC(max_channels, "Maximum number of channels to use (default: all)"); +static unsigned int iterations; +module_param(iterations, uint, S_IRUGO); +MODULE_PARM_DESC(iterations, + "Iterations before stopping test (default: infinite)"); + static unsigned int xor_sources = 3; module_param(xor_sources, uint, S_IRUGO); MODULE_PARM_DESC(xor_sources, @@ -270,7 +275,8 @@ static int dmatest_func(void *data) flags = DMA_CTRL_ACK | DMA_COMPL_SKIP_DEST_UNMAP | DMA_PREP_INTERRUPT; - while (!kthread_should_stop()) { + while (!kthread_should_stop() + && !(iterations && total_tests >= iterations)) { struct dma_device *dev = chan->device; struct dma_async_tx_descriptor *tx = NULL; dma_addr_t dma_srcs[src_cnt]; @@ -416,6 +422,13 @@ err_srcbuf: err_srcs: pr_notice("%s: terminating after %u tests, %u failures (status %d)\n", thread_name, total_tests, failed_tests, ret); + + if (iterations > 0) + while (!kthread_should_stop()) { + DECLARE_WAIT_QUEUE_HEAD(wait_dmatest_exit); + interruptible_sleep_on(&wait_dmatest_exit); + } + return ret; } -- cgit v1.2.3 From f1aef8b6e6abf32a3a269542f95a19e2cb319f6c Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Mon, 6 Jul 2009 18:19:44 +0200 Subject: dmaengine: dmatest: correct thread_count while using multiple thread per channel It seems that thread_count is not properly calculated in dmatest. In fact the thread count number that is returned from dmatest_add_threads() is not correctly added to the thread_count and thus not properly printed. Signed-off-by: Nicolas Ferre Acked-by: Haavard Skinnemoen Acked-by: Maciej Sosnowski Signed-off-by: Andrew Morton Signed-off-by: Dan Williams --- drivers/dma/dmatest.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c index 2d973d60e7b9..d93017fc7872 100644 --- a/drivers/dma/dmatest.c +++ b/drivers/dma/dmatest.c @@ -508,11 +508,11 @@ static int dmatest_add_channel(struct dma_chan *chan) if (dma_has_cap(DMA_MEMCPY, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_MEMCPY); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) { cnt = dmatest_add_threads(dtc, DMA_XOR); - thread_count += cnt > 0 ?: 0; + thread_count += cnt > 0 ? cnt : 0; } pr_info("dmatest: Started %u threads using %s\n", -- cgit v1.2.3 From dc78baa2b90b289590911b40b6800f77d0dc935a Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 3 Jul 2009 19:24:33 +0200 Subject: dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on at91sam9rl chip. It will be used on other products in the future. This first release covers only the memory-to-memory tranfer type. This is the only tranfer type supported by this chip. On other products, it will be used also for peripheral DMA transfer (slave API support to come). I used dmatest client without problem in different configurations to test it. Full documentation for this controller can be found in the SAM9RL datasheet: http://www.atmel.com/dyn/products/product_card.asp?part_id=4243 Signed-off-by: Nicolas Ferre Acked-by: Maciej Sosnowski Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 26 + drivers/dma/Kconfig | 8 + drivers/dma/Makefile | 1 + drivers/dma/at_hdmac.c | 1009 ++++++++++++++++++++++++++++ drivers/dma/at_hdmac_regs.h | 386 +++++++++++ 5 files changed, 1430 insertions(+) create mode 100644 arch/arm/mach-at91/include/mach/at_hdmac.h create mode 100644 drivers/dma/at_hdmac.c create mode 100644 drivers/dma/at_hdmac_regs.h (limited to 'drivers') diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h new file mode 100644 index 000000000000..21a5554f9cb8 --- /dev/null +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -0,0 +1,26 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_H +#define AT_HDMAC_H + +#include + +/** + * struct at_dma_platform_data - Controller configuration parameters + * @nr_channels: Number of channels supported by hardware (max 8) + * @cap_mask: dma_capability flags supported by the platform + */ +struct at_dma_platform_data { + unsigned int nr_channels; + dma_cap_mask_t cap_mask; +}; + +#endif /* AT_HDMAC_H */ diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index babf214a509b..bc8fb41cd623 100644 --- a/drivers/dma/Kconfig +++ b/drivers/dma/Kconfig @@ -46,6 +46,14 @@ config DW_DMAC Support the Synopsys DesignWare AHB DMA controller. This can be integrated in chips such as the Atmel AT32ap7000. +config AT_HDMAC + tristate "Atmel AHB DMA support" + depends on ARCH_AT91SAM9RL + select DMA_ENGINE + help + Support the Atmel AHB DMA controller. This can be integrated in + chips such as the Atmel AT91SAM9RL. + config FSL_DMA tristate "Freescale Elo and Elo Plus DMA support" depends on FSL_SOC diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile index 2e5dc96700d2..d7bc5fd17d84 100644 --- a/drivers/dma/Makefile +++ b/drivers/dma/Makefile @@ -7,4 +7,5 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o obj-$(CONFIG_FSL_DMA) += fsldma.o obj-$(CONFIG_MV_XOR) += mv_xor.o obj-$(CONFIG_DW_DMAC) += dw_dmac.o +obj-$(CONFIG_AT_HDMAC) += at_hdmac.o obj-$(CONFIG_MX3_IPU) += ipu/ diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c new file mode 100644 index 000000000000..64dbf0ce128e --- /dev/null +++ b/drivers/dma/at_hdmac.c @@ -0,0 +1,1009 @@ +/* + * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems) + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * + * This supports the Atmel AHB DMA Controller, + * + * The driver has currently been tested with the Atmel AT91SAM9RL + * and AT91SAM9G45 series. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "at_hdmac_regs.h" + +/* + * Glossary + * -------- + * + * at_hdmac : Name of the ATmel AHB DMA Controller + * at_dma_ / atdma : ATmel DMA controller entity related + * atc_ / atchan : ATmel DMA Channel entity related + */ + +#define ATC_DEFAULT_CFG (ATC_FIFOCFG_HALFFIFO) +#define ATC_DEFAULT_CTRLA (0) +#define ATC_DEFAULT_CTRLB (ATC_SIF(0) \ + |ATC_DIF(1)) + +/* + * Initial number of descriptors to allocate for each channel. This could + * be increased during dma usage. + */ +static unsigned int init_nr_desc_per_channel = 64; +module_param(init_nr_desc_per_channel, uint, 0644); +MODULE_PARM_DESC(init_nr_desc_per_channel, + "initial descriptors per channel (default: 64)"); + + +/* prototypes */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx); + + +/*----------------------------------------------------------------------*/ + +static struct at_desc *atc_first_active(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->active_list, + struct at_desc, desc_node); +} + +static struct at_desc *atc_first_queued(struct at_dma_chan *atchan) +{ + return list_first_entry(&atchan->queue, + struct at_desc, desc_node); +} + +/** + * atc_alloc_descriptor - allocate and return an initilized descriptor + * @chan: the channel to allocate descriptors for + * @gfp_flags: GFP allocation flags + * + * Note: The ack-bit is positioned in the descriptor flag at creation time + * to make initial allocation more convenient. This bit will be cleared + * and control will be given to client at usage time (during + * preparation functions). + */ +static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan, + gfp_t gfp_flags) +{ + struct at_desc *desc = NULL; + struct at_dma *atdma = to_at_dma(chan->device); + dma_addr_t phys; + + desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys); + if (desc) { + memset(desc, 0, sizeof(struct at_desc)); + dma_async_tx_descriptor_init(&desc->txd, chan); + /* txd.flags will be overwritten in prep functions */ + desc->txd.flags = DMA_CTRL_ACK; + desc->txd.tx_submit = atc_tx_submit; + desc->txd.phys = phys; + } + + return desc; +} + +/** + * atc_desc_get - get a unsused descriptor from free_list + * @atchan: channel we want a new descriptor for + */ +static struct at_desc *atc_desc_get(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *ret = NULL; + unsigned int i = 0; + LIST_HEAD(tmp_list); + + spin_lock_bh(&atchan->lock); + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + i++; + if (async_tx_test_ack(&desc->txd)) { + list_del(&desc->desc_node); + ret = desc; + break; + } + dev_dbg(chan2dev(&atchan->chan_common), + "desc %p not ACKed\n", desc); + } + spin_unlock_bh(&atchan->lock); + dev_vdbg(chan2dev(&atchan->chan_common), + "scanned %u descriptors on freelist\n", i); + + /* no more descriptor available in initial pool: create one more */ + if (!ret) { + ret = atc_alloc_descriptor(&atchan->chan_common, GFP_ATOMIC); + if (ret) { + spin_lock_bh(&atchan->lock); + atchan->descs_allocated++; + spin_unlock_bh(&atchan->lock); + } else { + dev_err(chan2dev(&atchan->chan_common), + "not enough descriptors available\n"); + } + } + + return ret; +} + +/** + * atc_desc_put - move a descriptor, including any children, to the free list + * @atchan: channel we work on + * @desc: descriptor, at the head of a chain, to move to free list + */ +static void atc_desc_put(struct at_dma_chan *atchan, struct at_desc *desc) +{ + if (desc) { + struct at_desc *child; + + spin_lock_bh(&atchan->lock); + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + dev_vdbg(chan2dev(&atchan->chan_common), + "moving child desc %p to freelist\n", + child); + list_splice_init(&desc->txd.tx_list, &atchan->free_list); + dev_vdbg(chan2dev(&atchan->chan_common), + "moving desc %p to freelist\n", desc); + list_add(&desc->desc_node, &atchan->free_list); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_assign_cookie - compute and assign new cookie + * @atchan: channel we work on + * @desc: descriptor to asign cookie for + * + * Called with atchan->lock held and bh disabled + */ +static dma_cookie_t +atc_assign_cookie(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_cookie_t cookie = atchan->chan_common.cookie; + + if (++cookie < 0) + cookie = 1; + + atchan->chan_common.cookie = cookie; + desc->txd.cookie = cookie; + + return cookie; +} + +/** + * atc_dostart - starts the DMA engine for real + * @atchan: the channel we want to start + * @first: first descriptor in the list we want to begin with + * + * Called with atchan->lock held and bh disabled + */ +static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: Attempted to start non-idle channel\n"); + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); + + /* The tasklet will hopefully advance the queue... */ + return; + } + + vdbg_dump_regs(atchan); + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + channel_writel(atchan, SADDR, 0); + channel_writel(atchan, DADDR, 0); + channel_writel(atchan, CTRLA, 0); + channel_writel(atchan, CTRLB, 0); + channel_writel(atchan, DSCR, first->txd.phys); + dma_writel(atdma, CHER, atchan->mask); + + vdbg_dump_regs(atchan); +} + +/** + * atc_chain_complete - finish work for one transaction chain + * @atchan: channel we work on + * @desc: descriptor at the head of the chain we want do complete + * + * Called with atchan->lock held and bh disabled */ +static void +atc_chain_complete(struct at_dma_chan *atchan, struct at_desc *desc) +{ + dma_async_tx_callback callback; + void *param; + struct dma_async_tx_descriptor *txd = &desc->txd; + + dev_vdbg(chan2dev(&atchan->chan_common), + "descriptor %u complete\n", txd->cookie); + + atchan->completed_cookie = txd->cookie; + callback = txd->callback; + param = txd->callback_param; + + /* move children to free_list */ + list_splice_init(&txd->tx_list, &atchan->free_list); + /* move myself to free_list */ + list_move(&desc->desc_node, &atchan->free_list); + + /* unmap dma addresses */ + if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) { + if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.daddr, + desc->len, DMA_FROM_DEVICE); + } + if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) { + if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE) + dma_unmap_single(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + else + dma_unmap_page(chan2parent(&atchan->chan_common), + desc->lli.saddr, + desc->len, DMA_TO_DEVICE); + } + + /* + * The API requires that no submissions are done from a + * callback, so we don't need to drop the lock here + */ + if (callback) + callback(param); + + dma_run_dependencies(txd); +} + +/** + * atc_complete_all - finish work for all transactions + * @atchan: channel to complete transactions for + * + * Eventually submit queued descriptors if any + * + * Assume channel is idle while calling this function + * Called with atchan->lock held and bh disabled + */ +static void atc_complete_all(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_vdbg(chan2dev(&atchan->chan_common), "complete all\n"); + + BUG_ON(atc_chan_is_enabled(atchan)); + + /* + * Submit queued descriptors ASAP, i.e. before we go through + * the completed ones. + */ + if (!list_empty(&atchan->queue)) + atc_dostart(atchan, atc_first_queued(atchan)); + /* empty active_list now it is completed */ + list_splice_init(&atchan->active_list, &list); + /* empty queue list by moving descriptors (if any) to active_list */ + list_splice_init(&atchan->queue, &atchan->active_list); + + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + +/** + * atc_cleanup_descriptors - cleanup up finished descriptors in active_list + * @atchan: channel to be cleaned up + * + * Called with atchan->lock held and bh disabled + */ +static void atc_cleanup_descriptors(struct at_dma_chan *atchan) +{ + struct at_desc *desc, *_desc; + struct at_desc *child; + + dev_vdbg(chan2dev(&atchan->chan_common), "cleanup descriptors\n"); + + list_for_each_entry_safe(desc, _desc, &atchan->active_list, desc_node) { + if (!(desc->lli.ctrla & ATC_DONE)) + /* This one is currently in progress */ + return; + + list_for_each_entry(child, &desc->txd.tx_list, desc_node) + if (!(child->lli.ctrla & ATC_DONE)) + /* Currently in progress */ + return; + + /* + * No descriptors so far seem to be in progress, i.e. + * this chain must be done. + */ + atc_chain_complete(atchan, desc); + } +} + +/** + * atc_advance_work - at the end of a transaction, move forward + * @atchan: channel where the transaction ended + * + * Called with atchan->lock held and bh disabled + */ +static void atc_advance_work(struct at_dma_chan *atchan) +{ + dev_vdbg(chan2dev(&atchan->chan_common), "advance_work\n"); + + if (list_empty(&atchan->active_list) || + list_is_singular(&atchan->active_list)) { + atc_complete_all(atchan); + } else { + atc_chain_complete(atchan, atc_first_active(atchan)); + /* advance work */ + atc_dostart(atchan, atc_first_active(atchan)); + } +} + + +/** + * atc_handle_error - handle errors reported by DMA controller + * @atchan: channel where error occurs + * + * Called with atchan->lock held and bh disabled + */ +static void atc_handle_error(struct at_dma_chan *atchan) +{ + struct at_desc *bad_desc; + struct at_desc *child; + + /* + * The descriptor currently at the head of the active list is + * broked. Since we don't have any way to report errors, we'll + * just have to scream loudly and try to carry on. + */ + bad_desc = atc_first_active(atchan); + list_del_init(&bad_desc->desc_node); + + /* As we are stopped, take advantage to push queued descriptors + * in active_list */ + list_splice_init(&atchan->queue, atchan->active_list.prev); + + /* Try to restart the controller */ + if (!list_empty(&atchan->active_list)) + atc_dostart(atchan, atc_first_active(atchan)); + + /* + * KERN_CRITICAL may seem harsh, but since this only happens + * when someone submits a bad physical address in a + * descriptor, we should consider ourselves lucky that the + * controller flagged an error instead of scribbling over + * random memory locations. + */ + dev_crit(chan2dev(&atchan->chan_common), + "Bad descriptor submitted for DMA!\n"); + dev_crit(chan2dev(&atchan->chan_common), + " cookie: %d\n", bad_desc->txd.cookie); + atc_dump_lli(atchan, &bad_desc->lli); + list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node) + atc_dump_lli(atchan, &child->lli); + + /* Pretend the descriptor completed successfully */ + atc_chain_complete(atchan, bad_desc); +} + + +/*-- IRQ & Tasklet ---------------------------------------------------*/ + +static void atc_tasklet(unsigned long data) +{ + struct at_dma_chan *atchan = (struct at_dma_chan *)data; + + /* Channel cannot be enabled here */ + if (atc_chan_is_enabled(atchan)) { + dev_err(chan2dev(&atchan->chan_common), + "BUG: channel enabled in tasklet\n"); + return; + } + + spin_lock(&atchan->lock); + if (test_and_clear_bit(0, &atchan->error_status)) + atc_handle_error(atchan); + else + atc_advance_work(atchan); + + spin_unlock(&atchan->lock); +} + +static irqreturn_t at_dma_interrupt(int irq, void *dev_id) +{ + struct at_dma *atdma = (struct at_dma *)dev_id; + struct at_dma_chan *atchan; + int i; + u32 status, pending, imr; + int ret = IRQ_NONE; + + do { + imr = dma_readl(atdma, EBCIMR); + status = dma_readl(atdma, EBCISR); + pending = status & imr; + + if (!pending) + break; + + dev_vdbg(atdma->dma_common.dev, + "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n", + status, imr, pending); + + for (i = 0; i < atdma->dma_common.chancnt; i++) { + atchan = &atdma->chan[i]; + if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) { + if (pending & AT_DMA_ERR(i)) { + /* Disable channel on AHB error */ + dma_writel(atdma, CHDR, atchan->mask); + /* Give information to tasklet */ + set_bit(0, &atchan->error_status); + } + tasklet_schedule(&atchan->tasklet); + ret = IRQ_HANDLED; + } + } + + } while (pending); + + return ret; +} + + +/*-- DMA Engine API --------------------------------------------------*/ + +/** + * atc_tx_submit - set the prepared descriptor(s) to be executed by the engine + * @desc: descriptor at the head of the transaction chain + * + * Queue chain if DMA engine is working already + * + * Cookie increment and adding to active_list or queue must be atomic + */ +static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx) +{ + struct at_desc *desc = txd_to_at_desc(tx); + struct at_dma_chan *atchan = to_at_dma_chan(tx->chan); + dma_cookie_t cookie; + + spin_lock_bh(&atchan->lock); + cookie = atc_assign_cookie(atchan, desc); + + if (list_empty(&atchan->active_list)) { + dev_vdbg(chan2dev(tx->chan), "tx_submit: started %u\n", + desc->txd.cookie); + atc_dostart(atchan, desc); + list_add_tail(&desc->desc_node, &atchan->active_list); + } else { + dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n", + desc->txd.cookie); + list_add_tail(&desc->desc_node, &atchan->queue); + } + + spin_unlock_bh(&atchan->lock); + + return cookie; +} + +/** + * atc_prep_dma_memcpy - prepare a memcpy operation + * @chan: the channel to prepare operation on + * @dest: operation virtual destination address + * @src: operation virtual source address + * @len: operation length + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, + size_t len, unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_desc *desc = NULL; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + size_t xfer_count; + size_t offset; + unsigned int src_width; + unsigned int dst_width; + u32 ctrla; + u32 ctrlb; + + dev_vdbg(chan2dev(chan), "prep_dma_memcpy: d0x%x s0x%x l0x%zx f0x%lx\n", + dest, src, len, flags); + + if (unlikely(!len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + ctrla = ATC_DEFAULT_CTRLA; + ctrlb = ATC_DEFAULT_CTRLB + | ATC_SRC_ADDR_MODE_INCR + | ATC_DST_ADDR_MODE_INCR + | ATC_FC_MEM2MEM; + + /* + * We can be a lot more clever here, but this should take care + * of the most common optimization. + */ + if (!((src | dest | len) & 3)) { + ctrla |= ATC_SRC_WIDTH_WORD | ATC_DST_WIDTH_WORD; + src_width = dst_width = 2; + } else if (!((src | dest | len) & 1)) { + ctrla |= ATC_SRC_WIDTH_HALFWORD | ATC_DST_WIDTH_HALFWORD; + src_width = dst_width = 1; + } else { + ctrla |= ATC_SRC_WIDTH_BYTE | ATC_DST_WIDTH_BYTE; + src_width = dst_width = 0; + } + + for (offset = 0; offset < len; offset += xfer_count << src_width) { + xfer_count = min_t(size_t, (len - offset) >> src_width, + ATC_BTSIZE_MAX); + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + desc->lli.saddr = src + offset; + desc->lli.daddr = dest + offset; + desc->lli.ctrla = ctrla | xfer_count; + desc->lli.ctrlb = ctrlb; + + desc->txd.cookie = 0; + async_tx_ack(&desc->txd); + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + } + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = len; + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(desc); + + desc->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + atc_desc_put(atchan, first); + return NULL; +} + +/** + * atc_is_tx_complete - poll for transaction completion + * @chan: DMA channel + * @cookie: transaction identifier to check status of + * @done: if not %NULL, updated with last completed transaction + * @used: if not %NULL, updated with last used transaction + * + * If @done and @used are passed in, upon return they reflect the driver + * internal state and can be used with dma_async_is_complete() to check + * the status of multiple cookies without re-checking hardware state. + */ +static enum dma_status +atc_is_tx_complete(struct dma_chan *chan, + dma_cookie_t cookie, + dma_cookie_t *done, dma_cookie_t *used) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + dma_cookie_t last_used; + dma_cookie_t last_complete; + enum dma_status ret; + + dev_vdbg(chan2dev(chan), "is_tx_complete: %d (d%d, u%d)\n", + cookie, done ? *done : 0, used ? *used : 0); + + spin_lock_bh(atchan->lock); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + if (ret != DMA_SUCCESS) { + atc_cleanup_descriptors(atchan); + + last_complete = atchan->completed_cookie; + last_used = chan->cookie; + + ret = dma_async_is_complete(cookie, last_complete, last_used); + } + + spin_unlock_bh(atchan->lock); + + if (done) + *done = last_complete; + if (used) + *used = last_used; + + return ret; +} + +/** + * atc_issue_pending - try to finish work + * @chan: target DMA channel + */ +static void atc_issue_pending(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + dev_vdbg(chan2dev(chan), "issue_pending\n"); + + if (!atc_chan_is_enabled(atchan)) { + spin_lock_bh(&atchan->lock); + atc_advance_work(atchan); + spin_unlock_bh(&atchan->lock); + } +} + +/** + * atc_alloc_chan_resources - allocate resources for DMA channel + * @chan: allocate descriptor resources for this channel + * @client: current client requesting the channel be ready for requests + * + * return - the number of allocated descriptors + */ +static int atc_alloc_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc; + int i; + LIST_HEAD(tmp_list); + + dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); + + /* ASSERT: channel is idle */ + if (atc_chan_is_enabled(atchan)) { + dev_dbg(chan2dev(chan), "DMA channel not idle ?\n"); + return -EIO; + } + + /* have we already been set up? */ + if (!list_empty(&atchan->free_list)) + return atchan->descs_allocated; + + /* Allocate initial pool of descriptors */ + for (i = 0; i < init_nr_desc_per_channel; i++) { + desc = atc_alloc_descriptor(chan, GFP_KERNEL); + if (!desc) { + dev_err(atdma->dma_common.dev, + "Only %d initial descriptors\n", i); + break; + } + list_add_tail(&desc->desc_node, &tmp_list); + } + + spin_lock_bh(&atchan->lock); + atchan->descs_allocated = i; + list_splice(&tmp_list, &atchan->free_list); + atchan->completed_cookie = chan->cookie = 1; + spin_unlock_bh(&atchan->lock); + + /* channel parameters */ + channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + + dev_dbg(chan2dev(chan), + "alloc_chan_resources: allocated %d descriptors\n", + atchan->descs_allocated); + + return atchan->descs_allocated; +} + +/** + * atc_free_chan_resources - free all channel resources + * @chan: DMA channel + */ +static void atc_free_chan_resources(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + dev_dbg(chan2dev(chan), "free_chan_resources: (descs allocated=%u)\n", + atchan->descs_allocated); + + /* ASSERT: channel is idle */ + BUG_ON(!list_empty(&atchan->active_list)); + BUG_ON(!list_empty(&atchan->queue)); + BUG_ON(atc_chan_is_enabled(atchan)); + + list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) { + dev_vdbg(chan2dev(chan), " freeing descriptor %p\n", desc); + list_del(&desc->desc_node); + /* free link descriptor */ + dma_pool_free(atdma->dma_desc_pool, desc, desc->txd.phys); + } + list_splice_init(&atchan->free_list, &list); + atchan->descs_allocated = 0; + + dev_vdbg(chan2dev(chan), "free_chan_resources: done\n"); +} + + +/*-- Module Management -----------------------------------------------*/ + +/** + * at_dma_off - disable DMA controller + * @atdma: the Atmel HDAMC device + */ +static void at_dma_off(struct at_dma *atdma) +{ + dma_writel(atdma, EN, 0); + + /* disable all interrupts */ + dma_writel(atdma, EBCIDR, -1L); + + /* confirm that all channels are disabled */ + while (dma_readl(atdma, CHSR) & atdma->all_chan_mask) + cpu_relax(); +} + +static int __init at_dma_probe(struct platform_device *pdev) +{ + struct at_dma_platform_data *pdata; + struct resource *io; + struct at_dma *atdma; + size_t size; + int irq; + int err; + int i; + + /* get DMA Controller parameters from platform */ + pdata = pdev->dev.platform_data; + if (!pdata || pdata->nr_channels > AT_DMA_MAX_NR_CHANNELS) + return -EINVAL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!io) + return -EINVAL; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + size = sizeof(struct at_dma); + size += pdata->nr_channels * sizeof(struct at_dma_chan); + atdma = kzalloc(size, GFP_KERNEL); + if (!atdma) + return -ENOMEM; + + /* discover transaction capabilites from the platform data */ + atdma->dma_common.cap_mask = pdata->cap_mask; + atdma->all_chan_mask = (1 << pdata->nr_channels) - 1; + + size = io->end - io->start + 1; + if (!request_mem_region(io->start, size, pdev->dev.driver->name)) { + err = -EBUSY; + goto err_kfree; + } + + atdma->regs = ioremap(io->start, size); + if (!atdma->regs) { + err = -ENOMEM; + goto err_release_r; + } + + atdma->clk = clk_get(&pdev->dev, "dma_clk"); + if (IS_ERR(atdma->clk)) { + err = PTR_ERR(atdma->clk); + goto err_clk; + } + clk_enable(atdma->clk); + + /* force dma off, just in case */ + at_dma_off(atdma); + + err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma); + if (err) + goto err_irq; + + platform_set_drvdata(pdev, atdma); + + /* create a pool of consistent memory blocks for hardware descriptors */ + atdma->dma_desc_pool = dma_pool_create("at_hdmac_desc_pool", + &pdev->dev, sizeof(struct at_desc), + 4 /* word alignment */, 0); + if (!atdma->dma_desc_pool) { + dev_err(&pdev->dev, "No memory for descriptors dma pool\n"); + err = -ENOMEM; + goto err_pool_create; + } + + /* clear any pending interrupt */ + while (dma_readl(atdma, EBCISR)) + cpu_relax(); + + /* initialize channels related values */ + INIT_LIST_HEAD(&atdma->dma_common.channels); + for (i = 0; i < pdata->nr_channels; i++, atdma->dma_common.chancnt++) { + struct at_dma_chan *atchan = &atdma->chan[i]; + + atchan->chan_common.device = &atdma->dma_common; + atchan->chan_common.cookie = atchan->completed_cookie = 1; + atchan->chan_common.chan_id = i; + list_add_tail(&atchan->chan_common.device_node, + &atdma->dma_common.channels); + + atchan->ch_regs = atdma->regs + ch_regs(i); + spin_lock_init(&atchan->lock); + atchan->mask = 1 << i; + + INIT_LIST_HEAD(&atchan->active_list); + INIT_LIST_HEAD(&atchan->queue); + INIT_LIST_HEAD(&atchan->free_list); + + tasklet_init(&atchan->tasklet, atc_tasklet, + (unsigned long)atchan); + atc_enable_irq(atchan); + } + + /* set base routines */ + atdma->dma_common.device_alloc_chan_resources = atc_alloc_chan_resources; + atdma->dma_common.device_free_chan_resources = atc_free_chan_resources; + atdma->dma_common.device_is_tx_complete = atc_is_tx_complete; + atdma->dma_common.device_issue_pending = atc_issue_pending; + atdma->dma_common.dev = &pdev->dev; + + /* set prep routines based on capability */ + if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) + atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + + dma_writel(atdma, EN, AT_DMA_ENABLE); + + dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", + dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask) ? "cpy " : "", + dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask) ? "slave " : "", + atdma->dma_common.chancnt); + + dma_async_device_register(&atdma->dma_common); + + return 0; + +err_pool_create: + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); +err_irq: + clk_disable(atdma->clk); + clk_put(atdma->clk); +err_clk: + iounmap(atdma->regs); + atdma->regs = NULL; +err_release_r: + release_mem_region(io->start, size); +err_kfree: + kfree(atdma); + return err; +} + +static int __exit at_dma_remove(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + struct dma_chan *chan, *_chan; + struct resource *io; + + at_dma_off(atdma); + dma_async_device_unregister(&atdma->dma_common); + + dma_pool_destroy(atdma->dma_desc_pool); + platform_set_drvdata(pdev, NULL); + free_irq(platform_get_irq(pdev, 0), atdma); + + list_for_each_entry_safe(chan, _chan, &atdma->dma_common.channels, + device_node) { + struct at_dma_chan *atchan = to_at_dma_chan(chan); + + /* Disable interrupts */ + atc_disable_irq(atchan); + tasklet_disable(&atchan->tasklet); + + tasklet_kill(&atchan->tasklet); + list_del(&chan->device_node); + } + + clk_disable(atdma->clk); + clk_put(atdma->clk); + + iounmap(atdma->regs); + atdma->regs = NULL; + + io = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(io->start, io->end - io->start + 1); + + kfree(atdma); + + return 0; +} + +static void at_dma_shutdown(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); +} + +static int at_dma_suspend_late(struct platform_device *pdev, pm_message_t mesg) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + at_dma_off(platform_get_drvdata(pdev)); + clk_disable(atdma->clk); + return 0; +} + +static int at_dma_resume_early(struct platform_device *pdev) +{ + struct at_dma *atdma = platform_get_drvdata(pdev); + + clk_enable(atdma->clk); + dma_writel(atdma, EN, AT_DMA_ENABLE); + return 0; + +} + +static struct platform_driver at_dma_driver = { + .remove = __exit_p(at_dma_remove), + .shutdown = at_dma_shutdown, + .suspend_late = at_dma_suspend_late, + .resume_early = at_dma_resume_early, + .driver = { + .name = "at_hdmac", + }, +}; + +static int __init at_dma_init(void) +{ + return platform_driver_probe(&at_dma_driver, at_dma_probe); +} +module_init(at_dma_init); + +static void __exit at_dma_exit(void) +{ + platform_driver_unregister(&at_dma_driver); +} +module_exit(at_dma_exit); + +MODULE_DESCRIPTION("Atmel AHB DMA Controller driver"); +MODULE_AUTHOR("Nicolas Ferre "); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:at_hdmac"); diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h new file mode 100644 index 000000000000..ad2d4f402bf7 --- /dev/null +++ b/drivers/dma/at_hdmac_regs.h @@ -0,0 +1,386 @@ +/* + * Header file for the Atmel AHB DMA Controller driver + * + * Copyright (C) 2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#ifndef AT_HDMAC_REGS_H +#define AT_HDMAC_REGS_H + +#include + +#define AT_DMA_MAX_NR_CHANNELS 8 + + +#define AT_DMA_GCFG 0x00 /* Global Configuration Register */ +#define AT_DMA_IF_BIGEND(i) (0x1 << (i)) /* AHB-Lite Interface i in Big-endian mode */ +#define AT_DMA_ARB_CFG (0x1 << 4) /* Arbiter mode. */ +#define AT_DMA_ARB_CFG_FIXED (0x0 << 4) +#define AT_DMA_ARB_CFG_ROUND_ROBIN (0x1 << 4) + +#define AT_DMA_EN 0x04 /* Controller Enable Register */ +#define AT_DMA_ENABLE (0x1 << 0) + +#define AT_DMA_SREQ 0x08 /* Software Single Request Register */ +#define AT_DMA_SSREQ(x) (0x1 << ((x) << 1)) /* Request a source single transfer on channel x */ +#define AT_DMA_DSREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination single transfer on channel x */ + +#define AT_DMA_CREQ 0x0C /* Software Chunk Transfer Request Register */ +#define AT_DMA_SCREQ(x) (0x1 << ((x) << 1)) /* Request a source chunk transfer on channel x */ +#define AT_DMA_DCREQ(x) (0x1 << (1 + ((x) << 1))) /* Request a destination chunk transfer on channel x */ + +#define AT_DMA_LAST 0x10 /* Software Last Transfer Flag Register */ +#define AT_DMA_SLAST(x) (0x1 << ((x) << 1)) /* This src rq is last tx of buffer on channel x */ +#define AT_DMA_DLAST(x) (0x1 << (1 + ((x) << 1))) /* This dst rq is last tx of buffer on channel x */ + +#define AT_DMA_SYNC 0x14 /* Request Synchronization Register */ +#define AT_DMA_SYR(h) (0x1 << (h)) /* Synchronize handshake line h */ + +/* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */ +#define AT_DMA_EBCIER 0x18 /* Enable register */ +#define AT_DMA_EBCIDR 0x1C /* Disable register */ +#define AT_DMA_EBCIMR 0x20 /* Mask Register */ +#define AT_DMA_EBCISR 0x24 /* Status Register */ +#define AT_DMA_CBTC_OFFSET 8 +#define AT_DMA_ERR_OFFSET 16 +#define AT_DMA_BTC(x) (0x1 << (x)) +#define AT_DMA_CBTC(x) (0x1 << (AT_DMA_CBTC_OFFSET + (x))) +#define AT_DMA_ERR(x) (0x1 << (AT_DMA_ERR_OFFSET + (x))) + +#define AT_DMA_CHER 0x28 /* Channel Handler Enable Register */ +#define AT_DMA_ENA(x) (0x1 << (x)) +#define AT_DMA_SUSP(x) (0x1 << ( 8 + (x))) +#define AT_DMA_KEEP(x) (0x1 << (24 + (x))) + +#define AT_DMA_CHDR 0x2C /* Channel Handler Disable Register */ +#define AT_DMA_DIS(x) (0x1 << (x)) +#define AT_DMA_RES(x) (0x1 << ( 8 + (x))) + +#define AT_DMA_CHSR 0x30 /* Channel Handler Status Register */ +#define AT_DMA_EMPT(x) (0x1 << (16 + (x))) +#define AT_DMA_STAL(x) (0x1 << (24 + (x))) + + +#define AT_DMA_CH_REGS_BASE 0x3C /* Channel registers base address */ +#define ch_regs(x) (AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */ + +/* Hardware register offset for each channel */ +#define ATC_SADDR_OFFSET 0x00 /* Source Address Register */ +#define ATC_DADDR_OFFSET 0x04 /* Destination Address Register */ +#define ATC_DSCR_OFFSET 0x08 /* Descriptor Address Register */ +#define ATC_CTRLA_OFFSET 0x0C /* Control A Register */ +#define ATC_CTRLB_OFFSET 0x10 /* Control B Register */ +#define ATC_CFG_OFFSET 0x14 /* Configuration Register */ +#define ATC_SPIP_OFFSET 0x18 /* Src PIP Configuration Register */ +#define ATC_DPIP_OFFSET 0x1C /* Dst PIP Configuration Register */ + + +/* Bitfield definitions */ + +/* Bitfields in DSCR */ +#define ATC_DSCR_IF(i) (0x3 & (i)) /* Dsc feched via AHB-Lite Interface i */ + +/* Bitfields in CTRLA */ +#define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ +#define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) +#define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH_BYTE (0x0 << 24) +#define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) +#define ATC_SRC_WIDTH_WORD (0x2 << 24) +#define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH_BYTE (0x0 << 28) +#define ATC_DST_WIDTH_HALFWORD (0x1 << 28) +#define ATC_DST_WIDTH_WORD (0x2 << 28) +#define ATC_DONE (0x1 << 31) /* Tx Done (only written back in descriptor) */ + +/* Bitfields in CTRLB */ +#define ATC_SIF(i) (0x3 & (i)) /* Src tx done via AHB-Lite Interface i */ +#define ATC_DIF(i) ((0x3 & (i)) << 4) /* Dst tx done via AHB-Lite Interface i */ +#define ATC_SRC_PIP (0x1 << 8) /* Source Picture-in-Picture enabled */ +#define ATC_DST_PIP (0x1 << 12) /* Destination Picture-in-Picture enabled */ +#define ATC_SRC_DSCR_DIS (0x1 << 16) /* Src Descriptor fetch disable */ +#define ATC_DST_DSCR_DIS (0x1 << 20) /* Dst Descriptor fetch disable */ +#define ATC_FC_MASK (0x7 << 21) /* Choose Flow Controller */ +#define ATC_FC_MEM2MEM (0x0 << 21) /* Mem-to-Mem (DMA) */ +#define ATC_FC_MEM2PER (0x1 << 21) /* Mem-to-Periph (DMA) */ +#define ATC_FC_PER2MEM (0x2 << 21) /* Periph-to-Mem (DMA) */ +#define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ +#define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ +#define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ +#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) +#define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ +#define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ +#define ATC_SRC_ADDR_MODE_FIXED (0x2 << 24) /* Fixed Mode */ +#define ATC_DST_ADDR_MODE_MASK (0x3 << 28) +#define ATC_DST_ADDR_MODE_INCR (0x0 << 28) /* Incrementing Mode */ +#define ATC_DST_ADDR_MODE_DECR (0x1 << 28) /* Decrementing Mode */ +#define ATC_DST_ADDR_MODE_FIXED (0x2 << 28) /* Fixed Mode */ +#define ATC_IEN (0x1 << 30) /* BTC interrupt enable (active low) */ +#define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ + +/* Bitfields in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Bitfields in SPIP */ +#define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_SPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + +/* Bitfields in DPIP */ +#define ATC_DPIP_HOLE(x) (0xFFFFU & (x)) +#define ATC_DPIP_BOUNDARY(x) ((0x3FF & (x)) << 16) + + +/*-- descriptors -----------------------------------------------------*/ + +/* LLI == Linked List Item; aka DMA buffer descriptor */ +struct at_lli { + /* values that are not changed by hardware */ + dma_addr_t saddr; + dma_addr_t daddr; + /* value that may get written back: */ + u32 ctrla; + /* more values that are not changed by hardware */ + u32 ctrlb; + dma_addr_t dscr; /* chain to next lli */ +}; + +/** + * struct at_desc - software descriptor + * @at_lli: hardware lli structure + * @txd: support for the async_tx api + * @desc_node: node on the channed descriptors list + * @len: total transaction bytecount + */ +struct at_desc { + /* FIRST values the hardware uses */ + struct at_lli lli; + + /* THEN values for driver housekeeping */ + struct dma_async_tx_descriptor txd; + struct list_head desc_node; + size_t len; +}; + +static inline struct at_desc * +txd_to_at_desc(struct dma_async_tx_descriptor *txd) +{ + return container_of(txd, struct at_desc, txd); +} + + +/*-- Channels --------------------------------------------------------*/ + +/** + * struct at_dma_chan - internal representation of an Atmel HDMAC channel + * @chan_common: common dmaengine channel object members + * @device: parent device + * @ch_regs: memory mapped register base + * @mask: channel index in a mask + * @error_status: transmit error status information from irq handler + * to tasklet (use atomic operations) + * @tasklet: bottom half to finish transaction work + * @lock: serializes enqueue/dequeue operations to descriptors lists + * @completed_cookie: identifier for the most recently completed operation + * @active_list: list of descriptors dmaengine is being running on + * @queue: list of descriptors ready to be submitted to engine + * @free_list: list of descriptors usable by the channel + * @descs_allocated: records the actual size of the descriptor pool + */ +struct at_dma_chan { + struct dma_chan chan_common; + struct at_dma *device; + void __iomem *ch_regs; + u8 mask; + unsigned long error_status; + struct tasklet_struct tasklet; + + spinlock_t lock; + + /* these other elements are all protected by lock */ + dma_cookie_t completed_cookie; + struct list_head active_list; + struct list_head queue; + struct list_head free_list; + unsigned int descs_allocated; +}; + +#define channel_readl(atchan, name) \ + __raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET) + +#define channel_writel(atchan, name, val) \ + __raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET) + +static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *dchan) +{ + return container_of(dchan, struct at_dma_chan, chan_common); +} + + +/*-- Controller ------------------------------------------------------*/ + +/** + * struct at_dma - internal representation of an Atmel HDMA Controller + * @chan_common: common dmaengine dma_device object members + * @ch_regs: memory mapped register base + * @clk: dma controller clock + * @all_chan_mask: all channels availlable in a mask + * @dma_desc_pool: base of DMA descriptor region (DMA address) + * @chan: channels table to store at_dma_chan structures + */ +struct at_dma { + struct dma_device dma_common; + void __iomem *regs; + struct clk *clk; + + u8 all_chan_mask; + + struct dma_pool *dma_desc_pool; + /* AT THE END channels table */ + struct at_dma_chan chan[0]; +}; + +#define dma_readl(atdma, name) \ + __raw_readl((atdma)->regs + AT_DMA_##name) +#define dma_writel(atdma, name, val) \ + __raw_writel((val), (atdma)->regs + AT_DMA_##name) + +static inline struct at_dma *to_at_dma(struct dma_device *ddev) +{ + return container_of(ddev, struct at_dma, dma_common); +} + + +/*-- Helper functions ------------------------------------------------*/ + +static struct device *chan2dev(struct dma_chan *chan) +{ + return &chan->dev->device; +} +static struct device *chan2parent(struct dma_chan *chan) +{ + return chan->dev->device.parent; +} + +#if defined(VERBOSE_DEBUG) +static void vdbg_dump_regs(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + dev_err(chan2dev(&atchan->chan_common), + " channel %d : imr = 0x%x, chsr = 0x%x\n", + atchan->chan_common.chan_id, + dma_readl(atdma, EBCIMR), + dma_readl(atdma, CHSR)); + + dev_err(chan2dev(&atchan->chan_common), + " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + channel_readl(atchan, SADDR), + channel_readl(atchan, DADDR), + channel_readl(atchan, CTRLA), + channel_readl(atchan, CTRLB), + channel_readl(atchan, DSCR)); +} +#else +static void vdbg_dump_regs(struct at_dma_chan *atchan) {} +#endif + +static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli) +{ + dev_printk(KERN_CRIT, chan2dev(&atchan->chan_common), + " desc: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + lli->saddr, lli->daddr, + lli->ctrla, lli->ctrlb, lli->dscr); +} + + +static void atc_setup_irq(struct at_dma_chan *atchan, int on) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + u32 ebci; + + /* enable interrupts on buffer chain completion & error */ + ebci = AT_DMA_CBTC(atchan->chan_common.chan_id) + | AT_DMA_ERR(atchan->chan_common.chan_id); + if (on) + dma_writel(atdma, EBCIER, ebci); + else + dma_writel(atdma, EBCIDR, ebci); +} + +static inline void atc_enable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 1); +} + +static inline void atc_disable_irq(struct at_dma_chan *atchan) +{ + atc_setup_irq(atchan, 0); +} + + +/** + * atc_chan_is_enabled - test if given channel is enabled + * @atchan: channel we want to test status + */ +static inline int atc_chan_is_enabled(struct at_dma_chan *atchan) +{ + struct at_dma *atdma = to_at_dma(atchan->chan_common.device); + + return !!(dma_readl(atdma, CHSR) & atchan->mask); +} + + +/** + * set_desc_eol - set end-of-link to descriptor so it will end transfer + * @desc: descriptor, signle or at the end of a chain, to end chain on + */ +static void set_desc_eol(struct at_desc *desc) +{ + desc->lli.ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS; + desc->lli.dscr = 0; +} + +#endif /* AT_HDMAC_REGS_H */ -- cgit v1.2.3 From 808347f6a31792079e345ec865e9cfcb6e8ae6b2 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 22 Jul 2009 20:04:45 +0200 Subject: dmaengine: at_hdmac: add DMA slave transfers This patch for at_hdmac adds the slave transfers capability to the Atmel DMA controller available on some AT91 SOCs. This allow peripheral to memory and memory to peripheral transfers with hardware handshaking. Slave structure for controller specific information is passed through channel private data. This at_dma_slave structure is defined in at_hdmac.h header file and relative hardware definition are moved to this file from at_hdmac_regs.h. Doing this we allow the channel configuration from platform definition code. This work is intensively based on dw_dmac and several slave implementations. Signed-off-by: Nicolas Ferre Signed-off-by: Dan Williams --- arch/arm/mach-at91/include/mach/at_hdmac.h | 76 +++++++++++ drivers/dma/at_hdmac.c | 208 ++++++++++++++++++++++++++++- drivers/dma/at_hdmac_regs.h | 49 ++----- 3 files changed, 290 insertions(+), 43 deletions(-) (limited to 'drivers') diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h index 21a5554f9cb8..187cb58345c0 100644 --- a/arch/arm/mach-at91/include/mach/at_hdmac.h +++ b/arch/arm/mach-at91/include/mach/at_hdmac.h @@ -23,4 +23,80 @@ struct at_dma_platform_data { dma_cap_mask_t cap_mask; }; +/** + * enum at_dma_slave_width - DMA slave register access width. + * @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses + * @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses + */ +enum at_dma_slave_width { + AT_DMA_SLAVE_WIDTH_8BIT = 0, + AT_DMA_SLAVE_WIDTH_16BIT, + AT_DMA_SLAVE_WIDTH_32BIT, +}; + +/** + * struct at_dma_slave - Controller-specific information about a slave + * @dma_dev: required DMA master device + * @tx_reg: physical address of data register used for + * memory-to-peripheral transfers + * @rx_reg: physical address of data register used for + * peripheral-to-memory transfers + * @reg_width: peripheral register width + * @cfg: Platform-specific initializer for the CFG register + * @ctrla: Platform-specific initializer for the CTRLA register + */ +struct at_dma_slave { + struct device *dma_dev; + dma_addr_t tx_reg; + dma_addr_t rx_reg; + enum at_dma_slave_width reg_width; + u32 cfg; + u32 ctrla; +}; + + +/* Platform-configurable bits in CFG */ +#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ +#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ +#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ +#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ +#define ATC_SRC_H2SEL_SW (0x0 << 9) +#define ATC_SRC_H2SEL_HW (0x1 << 9) +#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ +#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ +#define ATC_DST_H2SEL_SW (0x0 << 13) +#define ATC_DST_H2SEL_HW (0x1 << 13) +#define ATC_SOD (0x1 << 16) /* Stop On Done */ +#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ +#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ +#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ +#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) +#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) +#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ +#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ +#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) +#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) +#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) + +/* Platform-configurable bits in CTRLA */ +#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ +#define ATC_SCSIZE_1 (0x0 << 16) +#define ATC_SCSIZE_4 (0x1 << 16) +#define ATC_SCSIZE_8 (0x2 << 16) +#define ATC_SCSIZE_16 (0x3 << 16) +#define ATC_SCSIZE_32 (0x4 << 16) +#define ATC_SCSIZE_64 (0x5 << 16) +#define ATC_SCSIZE_128 (0x6 << 16) +#define ATC_SCSIZE_256 (0x7 << 16) +#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ +#define ATC_DCSIZE_1 (0x0 << 20) +#define ATC_DCSIZE_4 (0x1 << 20) +#define ATC_DCSIZE_8 (0x2 << 20) +#define ATC_DCSIZE_16 (0x3 << 20) +#define ATC_DCSIZE_32 (0x4 << 20) +#define ATC_DCSIZE_64 (0x5 << 20) +#define ATC_DCSIZE_128 (0x6 << 20) +#define ATC_DCSIZE_256 (0x7 << 20) + #endif /* AT_HDMAC_H */ diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c index 64dbf0ce128e..9a1e5fb412ed 100644 --- a/drivers/dma/at_hdmac.c +++ b/drivers/dma/at_hdmac.c @@ -608,6 +608,187 @@ err_desc_get: return NULL; } + +/** + * atc_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction + * @chan: DMA channel + * @sgl: scatterlist to transfer to/from + * @sg_len: number of entries in @scatterlist + * @direction: DMA direction + * @flags: tx descriptor status flags + */ +static struct dma_async_tx_descriptor * +atc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl, + unsigned int sg_len, enum dma_data_direction direction, + unsigned long flags) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma_slave *atslave = chan->private; + struct at_desc *first = NULL; + struct at_desc *prev = NULL; + u32 ctrla; + u32 ctrlb; + dma_addr_t reg; + unsigned int reg_width; + unsigned int mem_width; + unsigned int i; + struct scatterlist *sg; + size_t total_len = 0; + + dev_vdbg(chan2dev(chan), "prep_slave_sg: %s f0x%lx\n", + direction == DMA_TO_DEVICE ? "TO DEVICE" : "FROM DEVICE", + flags); + + if (unlikely(!atslave || !sg_len)) { + dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); + return NULL; + } + + reg_width = atslave->reg_width; + + sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction); + + ctrla = ATC_DEFAULT_CTRLA | atslave->ctrla; + ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN; + + switch (direction) { + case DMA_TO_DEVICE: + ctrla |= ATC_DST_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_FIXED + | ATC_SRC_ADDR_MODE_INCR + | ATC_FC_MEM2PER; + reg = atslave->tx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = mem; + desc->lli.daddr = reg; + desc->lli.ctrla = ctrla + | ATC_SRC_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + case DMA_FROM_DEVICE: + ctrla |= ATC_SRC_WIDTH(reg_width); + ctrlb |= ATC_DST_ADDR_MODE_INCR + | ATC_SRC_ADDR_MODE_FIXED + | ATC_FC_PER2MEM; + + reg = atslave->rx_reg; + for_each_sg(sgl, sg, sg_len, i) { + struct at_desc *desc; + u32 len; + u32 mem; + + desc = atc_desc_get(atchan); + if (!desc) + goto err_desc_get; + + mem = sg_phys(sg); + len = sg_dma_len(sg); + mem_width = 2; + if (unlikely(mem & 3 || len & 3)) + mem_width = 0; + + desc->lli.saddr = reg; + desc->lli.daddr = mem; + desc->lli.ctrla = ctrla + | ATC_DST_WIDTH(mem_width) + | len >> mem_width; + desc->lli.ctrlb = ctrlb; + + if (!first) { + first = desc; + } else { + /* inform the HW lli about chaining */ + prev->lli.dscr = desc->txd.phys; + /* insert the link descriptor to the LD ring */ + list_add_tail(&desc->desc_node, + &first->txd.tx_list); + } + prev = desc; + total_len += len; + } + break; + default: + return NULL; + } + + /* set end-of-link to the last link descriptor of list*/ + set_desc_eol(prev); + + /* First descriptor of the chain embedds additional information */ + first->txd.cookie = -EBUSY; + first->len = total_len; + + /* last link descriptor of list is responsible of flags */ + prev->txd.flags = flags; /* client is in control of this ack */ + + return &first->txd; + +err_desc_get: + dev_err(chan2dev(chan), "not enough descriptors available\n"); + atc_desc_put(atchan, first); + return NULL; +} + +static void atc_terminate_all(struct dma_chan *chan) +{ + struct at_dma_chan *atchan = to_at_dma_chan(chan); + struct at_dma *atdma = to_at_dma(chan->device); + struct at_desc *desc, *_desc; + LIST_HEAD(list); + + /* + * This is only called when something went wrong elsewhere, so + * we don't really care about the data. Just disable the + * channel. We still have to poll the channel enable bit due + * to AHB/HSB limitations. + */ + spin_lock_bh(&atchan->lock); + + dma_writel(atdma, CHDR, atchan->mask); + + /* confirm that this channel is disabled */ + while (dma_readl(atdma, CHSR) & atchan->mask) + cpu_relax(); + + /* active_list entries will end up before queued entries */ + list_splice_init(&atchan->queue, &list); + list_splice_init(&atchan->active_list, &list); + + spin_unlock_bh(&atchan->lock); + + /* Flush all pending and queued descriptors */ + list_for_each_entry_safe(desc, _desc, &list, desc_node) + atc_chain_complete(atchan, desc); +} + /** * atc_is_tx_complete - poll for transaction completion * @chan: DMA channel @@ -686,7 +867,9 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) struct at_dma_chan *atchan = to_at_dma_chan(chan); struct at_dma *atdma = to_at_dma(chan->device); struct at_desc *desc; + struct at_dma_slave *atslave; int i; + u32 cfg; LIST_HEAD(tmp_list); dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); @@ -697,7 +880,23 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) return -EIO; } - /* have we already been set up? */ + cfg = ATC_DEFAULT_CFG; + + atslave = chan->private; + if (atslave) { + /* + * We need controller-specific data to set up slave + * transfers. + */ + BUG_ON(!atslave->dma_dev || atslave->dma_dev != atdma->dma_common.dev); + + /* if cfg configuration specified take it instad of default */ + if (atslave->cfg) + cfg = atslave->cfg; + } + + /* have we already been set up? + * reconfigure channel but no need to reallocate descriptors */ if (!list_empty(&atchan->free_list)) return atchan->descs_allocated; @@ -719,7 +918,7 @@ static int atc_alloc_chan_resources(struct dma_chan *chan) spin_unlock_bh(&atchan->lock); /* channel parameters */ - channel_writel(atchan, CFG, ATC_DEFAULT_CFG); + channel_writel(atchan, CFG, cfg); dev_dbg(chan2dev(chan), "alloc_chan_resources: allocated %d descriptors\n", @@ -888,6 +1087,11 @@ static int __init at_dma_probe(struct platform_device *pdev) if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask)) atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy; + if (dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)) { + atdma->dma_common.device_prep_slave_sg = atc_prep_slave_sg; + atdma->dma_common.device_terminate_all = atc_terminate_all; + } + dma_writel(atdma, EN, AT_DMA_ENABLE); dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n", diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h index ad2d4f402bf7..4c972afc49ec 100644 --- a/drivers/dma/at_hdmac_regs.h +++ b/drivers/dma/at_hdmac_regs.h @@ -87,29 +87,14 @@ /* Bitfields in CTRLA */ #define ATC_BTSIZE_MAX 0xFFFFUL /* Maximum Buffer Transfer Size */ #define ATC_BTSIZE(x) (ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */ -#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */ -#define ATC_SCSIZE_1 (0x0 << 16) -#define ATC_SCSIZE_4 (0x1 << 16) -#define ATC_SCSIZE_8 (0x2 << 16) -#define ATC_SCSIZE_16 (0x3 << 16) -#define ATC_SCSIZE_32 (0x4 << 16) -#define ATC_SCSIZE_64 (0x5 << 16) -#define ATC_SCSIZE_128 (0x6 << 16) -#define ATC_SCSIZE_256 (0x7 << 16) -#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */ -#define ATC_DCSIZE_1 (0x0 << 20) -#define ATC_DCSIZE_4 (0x1 << 20) -#define ATC_DCSIZE_8 (0x2 << 20) -#define ATC_DCSIZE_16 (0x3 << 20) -#define ATC_DCSIZE_32 (0x4 << 20) -#define ATC_DCSIZE_64 (0x5 << 20) -#define ATC_DCSIZE_128 (0x6 << 20) -#define ATC_DCSIZE_256 (0x7 << 20) +/* Chunck Tranfer size definitions are in at_hdmac.h */ #define ATC_SRC_WIDTH_MASK (0x3 << 24) /* Source Single Transfer Size */ +#define ATC_SRC_WIDTH(x) ((x) << 24) #define ATC_SRC_WIDTH_BYTE (0x0 << 24) #define ATC_SRC_WIDTH_HALFWORD (0x1 << 24) #define ATC_SRC_WIDTH_WORD (0x2 << 24) #define ATC_DST_WIDTH_MASK (0x3 << 28) /* Destination Single Transfer Size */ +#define ATC_DST_WIDTH(x) ((x) << 28) #define ATC_DST_WIDTH_BYTE (0x0 << 28) #define ATC_DST_WIDTH_HALFWORD (0x1 << 28) #define ATC_DST_WIDTH_WORD (0x2 << 28) @@ -129,7 +114,8 @@ #define ATC_FC_PER2PER (0x3 << 21) /* Periph-to-Periph (DMA) */ #define ATC_FC_PER2MEM_PER (0x4 << 21) /* Periph-to-Mem (Peripheral) */ #define ATC_FC_MEM2PER_PER (0x5 << 21) /* Mem-to-Periph (Peripheral) */ -#define ATC_FC_PER2PER_PER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_SRCPER (0x6 << 21) /* Periph-to-Periph (Src Peripheral) */ +#define ATC_FC_PER2PER_DSTPER (0x7 << 21) /* Periph-to-Periph (Dst Peripheral) */ #define ATC_SRC_ADDR_MODE_MASK (0x3 << 24) #define ATC_SRC_ADDR_MODE_INCR (0x0 << 24) /* Incrementing Mode */ #define ATC_SRC_ADDR_MODE_DECR (0x1 << 24) /* Decrementing Mode */ @@ -142,27 +128,7 @@ #define ATC_AUTO (0x1 << 31) /* Auto multiple buffer tx enable */ /* Bitfields in CFG */ -#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */ -#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */ -#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */ -#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */ -#define ATC_SRC_H2SEL_SW (0x0 << 9) -#define ATC_SRC_H2SEL_HW (0x1 << 9) -#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */ -#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */ -#define ATC_DST_H2SEL_SW (0x0 << 13) -#define ATC_DST_H2SEL_HW (0x1 << 13) -#define ATC_SOD (0x1 << 16) /* Stop On Done */ -#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */ -#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */ -#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */ -#define ATC_LOCK_IF_L_CHUNK (0x0 << 22) -#define ATC_LOCK_IF_L_BUFFER (0x1 << 22) -#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */ -#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */ -#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28) -#define ATC_FIFOCFG_HALFFIFO (0x1 << 28) -#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28) +/* are in at_hdmac.h */ /* Bitfields in SPIP */ #define ATC_SPIP_HOLE(x) (0xFFFFU & (x)) @@ -316,11 +282,12 @@ static void vdbg_dump_regs(struct at_dma_chan *atchan) dma_readl(atdma, CHSR)); dev_err(chan2dev(&atchan->chan_common), - " channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n", + " channel: s0x%x d0x%x ctrl0x%x:0x%x cfg0x%x l0x%x\n", channel_readl(atchan, SADDR), channel_readl(atchan, DADDR), channel_readl(atchan, CTRLA), channel_readl(atchan, CTRLB), + channel_readl(atchan, CFG), channel_readl(atchan, DSCR)); } #else -- cgit v1.2.3 From dacac4da5290ee3f3f413bd6980af2befb813e28 Mon Sep 17 00:00:00 2001 From: Mark Ware Date: Thu, 23 Jul 2009 10:56:48 -0700 Subject: net: Rework mdio-ofgpio driver to use of_mdio infrastructure Changes to the fs_enet driver aa73832c5a80d6c52c69b18af858d88fa595dd3c ("net: Rework fs_enet driver to use of_mdio infrastructure") cause kernel crashes when using the mdio-ofgpio driver. This patch replicates similar changes made to the fs_enet mii-bitbang drivers. It has been tested on a custom mpc8280 based board using an NFS mounted root. Signed-off-by: Mark Ware Acked-by: Grant Likely Signed-off-by: David S. Miller --- drivers/net/phy/mdio-gpio.c | 77 +++++++++++++++++++++------------------------ 1 file changed, 36 insertions(+), 41 deletions(-) (limited to 'drivers') diff --git a/drivers/net/phy/mdio-gpio.c b/drivers/net/phy/mdio-gpio.c index 33984b737233..22cdd451fb82 100644 --- a/drivers/net/phy/mdio-gpio.c +++ b/drivers/net/phy/mdio-gpio.c @@ -30,6 +30,7 @@ #ifdef CONFIG_OF_GPIO #include +#include #include #endif @@ -81,13 +82,12 @@ static struct mdiobb_ops mdio_gpio_ops = { .get_mdio_data = mdio_get, }; -static int __devinit mdio_gpio_bus_init(struct device *dev, +static struct mii_bus * __devinit mdio_gpio_bus_init(struct device *dev, struct mdio_gpio_platform_data *pdata, int bus_id) { struct mii_bus *new_bus; struct mdio_gpio_info *bitbang; - int ret = -ENOMEM; int i; bitbang = kzalloc(sizeof(*bitbang), GFP_KERNEL); @@ -104,8 +104,6 @@ static int __devinit mdio_gpio_bus_init(struct device *dev, new_bus->name = "GPIO Bitbanged MDIO", - ret = -ENODEV; - new_bus->phy_mask = pdata->phy_mask; new_bus->irq = pdata->irqs; new_bus->parent = dev; @@ -129,15 +127,8 @@ static int __devinit mdio_gpio_bus_init(struct device *dev, dev_set_drvdata(dev, new_bus); - ret = mdiobus_register(new_bus); - if (ret) - goto out_free_all; - - return 0; + return new_bus; -out_free_all: - dev_set_drvdata(dev, NULL); - gpio_free(bitbang->mdio); out_free_mdc: gpio_free(bitbang->mdc); out_free_bus: @@ -145,30 +136,47 @@ out_free_bus: out_free_bitbang: kfree(bitbang); out: - return ret; + return NULL; } -static void __devexit mdio_gpio_bus_destroy(struct device *dev) +static void __devinit mdio_gpio_bus_deinit(struct device *dev) { struct mii_bus *bus = dev_get_drvdata(dev); struct mdio_gpio_info *bitbang = bus->priv; - mdiobus_unregister(bus); - free_mdio_bitbang(bus); dev_set_drvdata(dev, NULL); - gpio_free(bitbang->mdc); gpio_free(bitbang->mdio); + gpio_free(bitbang->mdc); + free_mdio_bitbang(bus); kfree(bitbang); } +static void __devexit mdio_gpio_bus_destroy(struct device *dev) +{ + struct mii_bus *bus = dev_get_drvdata(dev); + + mdiobus_unregister(bus); + mdio_gpio_bus_deinit(dev); +} + static int __devinit mdio_gpio_probe(struct platform_device *pdev) { struct mdio_gpio_platform_data *pdata = pdev->dev.platform_data; + struct mii_bus *new_bus; + int ret; if (!pdata) return -ENODEV; - return mdio_gpio_bus_init(&pdev->dev, pdata, pdev->id); + new_bus = mdio_gpio_bus_init(&pdev->dev, pdata, pdev->id); + if (!new_bus) + return -ENODEV; + + ret = mdiobus_register(new_bus); + if (ret) + mdio_gpio_bus_deinit(&pdev->dev); + + return ret; } static int __devexit mdio_gpio_remove(struct platform_device *pdev) @@ -179,29 +187,12 @@ static int __devexit mdio_gpio_remove(struct platform_device *pdev) } #ifdef CONFIG_OF_GPIO -static void __devinit add_phy(struct mdio_gpio_platform_data *pdata, - struct device_node *np) -{ - const u32 *data; - int len, id, irq; - - data = of_get_property(np, "reg", &len); - if (!data || len != 4) - return; - - id = *data; - pdata->phy_mask &= ~(1 << id); - - irq = of_irq_to_resource(np, 0, NULL); - if (irq) - pdata->irqs[id] = irq; -} static int __devinit mdio_ofgpio_probe(struct of_device *ofdev, const struct of_device_id *match) { - struct device_node *np = NULL; struct mdio_gpio_platform_data *pdata; + struct mii_bus *new_bus; int ret; pdata = kzalloc(sizeof(*pdata), GFP_KERNEL); @@ -215,14 +206,18 @@ static int __devinit mdio_ofgpio_probe(struct of_device *ofdev, ret = of_get_gpio(ofdev->node, 1); if (ret < 0) - goto out_free; + goto out_free; pdata->mdio = ret; - while ((np = of_get_next_child(ofdev->node, np))) - if (!strcmp(np->type, "ethernet-phy")) - add_phy(pdata, np); + new_bus = mdio_gpio_bus_init(&ofdev->dev, pdata, pdata->mdc); + if (!new_bus) + return -ENODEV; - return mdio_gpio_bus_init(&ofdev->dev, pdata, pdata->mdc); + ret = of_mdiobus_register(new_bus, ofdev->node); + if (ret) + mdio_gpio_bus_deinit(&ofdev->dev); + + return ret; out_free: kfree(pdata); -- cgit v1.2.3 From 0d5515894fd5b9e9402ef76e9a7e704fd26e0e5f Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Wed, 22 Jul 2009 14:07:12 +0000 Subject: ixgbe: Enable FCoE offload when DCB is enabled for 82599 Currently, FCoE offload feature is turned on when the kernel config has CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn FCoE offload on when there is FCoE traffic passing and turn it off when it's just LAN traffic. Since FCoE depends on a lossless network provided by DCB, this allows us to have FCoE turned on/off when user turns on DCB using dcbtool. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 1 + drivers/net/ixgbe/ixgbe_dcb_nl.c | 24 ++++++++++++++++++++++++ drivers/net/ixgbe/ixgbe_main.c | 16 ++++++---------- 3 files changed, 31 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index cd22323cfd22..1b12c7ba275f 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -327,6 +327,7 @@ struct ixgbe_adapter { #define IXGBE_FLAG_IN_SFP_MOD_TASK (u32)(1 << 25) #define IXGBE_FLAG_FDIR_HASH_CAPABLE (u32)(1 << 26) #define IXGBE_FLAG_FDIR_PERFECT_CAPABLE (u32)(1 << 27) +#define IXGBE_FLAG_FCOE_CAPABLE (u32)(1 << 28) #define IXGBE_FLAG_FCOE_ENABLED (u32)(1 << 29) u32 flags2; diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c index da2c8514b8d0..1c7265732900 100644 --- a/drivers/net/ixgbe/ixgbe_dcb_nl.c +++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c @@ -139,6 +139,18 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) adapter->flags &= ~IXGBE_FLAG_FDIR_PERFECT_CAPABLE; } adapter->flags |= IXGBE_FLAG_DCB_ENABLED; +#ifdef IXGBE_FCOE + /* Turn on FCoE offload */ + if ((adapter->flags & IXGBE_FLAG_FCOE_CAPABLE) && + (!(adapter->flags & IXGBE_FLAG_FCOE_ENABLED))) { + adapter->flags |= IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = + IXGBE_FCRETA_SIZE; + netdev->features |= NETIF_F_FCOE_CRC; + netdev->features |= NETIF_F_FSO; + netdev->fcoe_ddp_xid = IXGBE_FCOE_DDP_MAX - 1; + } +#endif /* IXGBE_FCOE */ ixgbe_init_interrupt_scheme(adapter); if (netif_running(netdev)) netdev->netdev_ops->ndo_open(netdev); @@ -156,6 +168,18 @@ static u8 ixgbe_dcbnl_set_state(struct net_device *netdev, u8 state) adapter->flags |= IXGBE_FLAG_RSS_ENABLED; if (adapter->hw.mac.type == ixgbe_mac_82599EB) adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE; + +#ifdef IXGBE_FCOE + /* Turn off FCoE offload */ + if (adapter->flags & (IXGBE_FLAG_FCOE_CAPABLE | + IXGBE_FLAG_FCOE_ENABLED)) { + adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = 0; + netdev->features &= ~NETIF_F_FCOE_CRC; + netdev->features &= ~NETIF_F_FSO; + netdev->fcoe_ddp_xid = 0; + } +#endif /* IXGBE_FCOE */ ixgbe_init_interrupt_scheme(adapter); if (netif_running(netdev)) netdev->netdev_ops->ndo_open(netdev); diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e3442f47f932..a2119d79ccdd 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -3806,8 +3806,9 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) adapter->atr_sample_rate = 20; adapter->fdir_pballoc = 0; #ifdef IXGBE_FCOE - adapter->flags |= IXGBE_FLAG_FCOE_ENABLED; - adapter->ring_feature[RING_F_FCOE].indices = IXGBE_FCRETA_SIZE; + adapter->flags |= IXGBE_FLAG_FCOE_CAPABLE; + adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; + adapter->ring_feature[RING_F_FCOE].indices = 0; #endif /* IXGBE_FCOE */ } @@ -5580,16 +5581,11 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, #endif #ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { + if (adapter->flags & IXGBE_FLAG_FCOE_CAPABLE) { if (hw->mac.ops.get_device_caps) { hw->mac.ops.get_device_caps(hw, &device_caps); - if (!(device_caps & IXGBE_DEVICE_CAPS_FCOE_OFFLOADS)) { - netdev->features |= NETIF_F_FCOE_CRC; - netdev->features |= NETIF_F_FSO; - netdev->fcoe_ddp_xid = IXGBE_FCOE_DDP_MAX - 1; - } else { - adapter->flags &= ~IXGBE_FLAG_FCOE_ENABLED; - } + if (device_caps & IXGBE_DEVICE_CAPS_FCOE_OFFLOADS) + adapter->flags &= ~IXGBE_FLAG_FCOE_CAPABLE; } } #endif /* IXGBE_FCOE */ -- cgit v1.2.3 From 601278659d5717b4f7a14fbc9f2b9d559bba6aef Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Wed, 22 Jul 2009 14:07:33 +0000 Subject: ixgbe: Don't priority tag control frames in DCB mode Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a priority tag or vlan tag inserted. Ixgbe driver is currently priority tagging everything (if packet is not on a VLAN interface). This patch modifies DCB mode, so that packets marked with skb priority TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on the highest priority traffic class. Programs (like dcbd) can set the skb priority using a socket option. Or, a tc filter can be configured to set the priority value. Using the value TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel, and the bonding LACP code already sets the skb->priority field to this value. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index a2119d79ccdd..47a3c6d70569 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -34,6 +34,7 @@ #include #include #include +#include #include #include #include @@ -5126,9 +5127,6 @@ static int ixgbe_xmit_frame(struct sk_buff *skb, struct net_device *netdev) int count = 0; unsigned int f; - r_idx = skb->queue_mapping; - tx_ring = &adapter->tx_ring[r_idx]; - if (adapter->vlgrp && vlan_tx_tag_present(skb)) { tx_flags |= vlan_tx_tag_get(skb); if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { @@ -5138,11 +5136,19 @@ static int ixgbe_xmit_frame(struct sk_buff *skb, struct net_device *netdev) tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; tx_flags |= IXGBE_TX_FLAGS_VLAN; } else if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - tx_flags |= (skb->queue_mapping << 13); - tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; - tx_flags |= IXGBE_TX_FLAGS_VLAN; + if (skb->priority != TC_PRIO_CONTROL) { + tx_flags |= (skb->queue_mapping << 13); + tx_flags <<= IXGBE_TX_FLAGS_VLAN_SHIFT; + tx_flags |= IXGBE_TX_FLAGS_VLAN; + } else { + skb->queue_mapping = + adapter->ring_feature[RING_F_DCB].indices-1; + } } + r_idx = skb->queue_mapping; + tx_ring = &adapter->tx_ring[r_idx]; + if ((adapter->flags & IXGBE_FLAG_FCOE_ENABLED) && (skb->protocol == htons(ETH_P_FCOE))) tx_flags |= IXGBE_TX_FLAGS_FCOE; -- cgit v1.2.3 From ffafa60d496f80c250f2ae0340ae94434c0b0b4d Mon Sep 17 00:00:00 2001 From: Andy Gospodarek Date: Wed, 22 Jul 2009 09:34:00 +0000 Subject: ixgbe: remove unnecessary call to device_init_wakeup Calls to device_init_wakeup should not be necessary in drivers that use device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag for the device when initialized. Signed-off-by: Andy Gospodarek Acked-by: Peter P Waskiewicz Jr Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 47a3c6d70569..68877599f6db 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -5640,7 +5640,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, adapter->wol = 0; break; } - device_init_wakeup(&adapter->pdev->dev, true); device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); /* pick up the PCI bus settings for reporting later */ -- cgit v1.2.3 From 69885683d22d8c05910fd808c01fdce1322739b4 Mon Sep 17 00:00:00 2001 From: Mikulas Patocka Date: Thu, 23 Jul 2009 20:30:37 +0100 Subject: dm raid1: wake kmirrord when requeueing delayed bios after remote recovery The recent commit 7513c2a761d69d2a93f17146b3563527d3618ba0 (dm raid1: add is_remote_recovering hook for clusters) changed do_writes() to update the ms->writes list but forgot to wake up kmirrord to process it. The rule is that when anything is being added on ms->reads, ms->writes or ms->failures and the list was empty before we must call wakeup_mirrord (for immediate processing) or delayed_wake (for delayed processing). Otherwise the bios could sit on the list indefinitely. Signed-off-by: Mikulas Patocka CC: stable@kernel.org Signed-off-by: Alasdair G Kergon --- drivers/md/dm-raid1.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index ce8868c768cc..42a3e4341d60 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -638,6 +638,7 @@ static void do_writes(struct mirror_set *ms, struct bio_list *writes) spin_lock_irq(&ms->lock); bio_list_merge(&ms->writes, &requeue); spin_unlock_irq(&ms->lock); + delayed_wake(ms); } /* -- cgit v1.2.3 From a732c207d19e899845ae47139708af898daaf9fd Mon Sep 17 00:00:00 2001 From: Mike Snitzer Date: Thu, 23 Jul 2009 20:30:40 +0100 Subject: dm: remove queue next_ordered workaround for barriers This patch removes DM's bio-based vs request-based conditional setting of next_ordered. For bio-based DM the next_ordered check is no longer a concern (as that check is now in the __make_request path). For request-based DM the default of QUEUE_ORDERED_NONE is now appropriate. bio-based DM was changed to work-around the previously misplaced next_ordered check with this commit: 99360b4c18f7675b50d283301d46d755affe75fd request-based DM does not yet support barriers but reacted to the above bio-based DM change with this commit: 5d67aa2366ccb8257d103d0b43df855605c3c086 The above changes are no longer needed given Neil Brown's recent fix to put the next_ordered check in the __make_request path: db64f680ba4b5c56c4be59f0698000df89ff0281 Signed-off-by: Mike Snitzer Cc: Jun'ichi Nomura Cc: NeilBrown Acked-by: Kiyoshi Ueda Acked-by: Mikulas Patocka Signed-off-by: Alasdair G Kergon --- drivers/md/dm-table.c | 5 ----- drivers/md/dm.c | 10 ---------- drivers/md/dm.h | 1 - 3 files changed, 16 deletions(-) (limited to 'drivers') diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c index 2cba557d9e61..5d16d06613aa 100644 --- a/drivers/md/dm-table.c +++ b/drivers/md/dm-table.c @@ -830,11 +830,6 @@ unsigned dm_table_get_type(struct dm_table *t) return t->type; } -bool dm_table_bio_based(struct dm_table *t) -{ - return dm_table_get_type(t) == DM_TYPE_BIO_BASED; -} - bool dm_table_request_based(struct dm_table *t) { return dm_table_get_type(t) == DM_TYPE_REQUEST_BASED; diff --git a/drivers/md/dm.c b/drivers/md/dm.c index 9acd54a5cffb..8a311ea0d441 100644 --- a/drivers/md/dm.c +++ b/drivers/md/dm.c @@ -2203,16 +2203,6 @@ int dm_swap_table(struct mapped_device *md, struct dm_table *table) goto out; } - /* - * It is enought that blk_queue_ordered() is called only once when - * the first bio-based table is bound. - * - * This setting should be moved to alloc_dev() when request-based dm - * supports barrier. - */ - if (!md->map && dm_table_bio_based(table)) - blk_queue_ordered(md->queue, QUEUE_ORDERED_DRAIN, NULL); - __unbind(md); r = __bind(md, table, &limits); diff --git a/drivers/md/dm.h b/drivers/md/dm.h index 23278ae80f08..a7663eba17e2 100644 --- a/drivers/md/dm.h +++ b/drivers/md/dm.h @@ -61,7 +61,6 @@ int dm_table_any_congested(struct dm_table *t, int bdi_bits); int dm_table_any_busy_target(struct dm_table *t); int dm_table_set_type(struct dm_table *t); unsigned dm_table_get_type(struct dm_table *t); -bool dm_table_bio_based(struct dm_table *t); bool dm_table_request_based(struct dm_table *t); int dm_table_alloc_md_mempools(struct dm_table *t); void dm_table_free_md_mempools(struct dm_table *t); -- cgit v1.2.3 From 5dea271b6d87bd1d79a59c1d5baac2596a841c37 Mon Sep 17 00:00:00 2001 From: Mike Snitzer Date: Thu, 23 Jul 2009 20:30:42 +0100 Subject: dm table: pass correct dev area size to device_area_is_valid Incorrect device area lengths are being passed to device_area_is_valid(). The regression appeared in 2.6.31-rc1 through commit 754c5fc7ebb417b23601a6222a6005cc2e7f2913. With the dm-stripe target, the size of the target (ti->len) was used instead of the stripe_width (ti->len/#stripes). An example of a consequent incorrect error message is: device-mapper: table: 254:0: sdb too small for target Signed-off-by: Mike Snitzer Signed-off-by: Alasdair G Kergon --- drivers/md/dm-crypt.c | 2 +- drivers/md/dm-delay.c | 4 ++-- drivers/md/dm-linear.c | 2 +- drivers/md/dm-mpath.c | 2 +- drivers/md/dm-raid1.c | 2 +- drivers/md/dm-stripe.c | 7 ++++--- drivers/md/dm-table.c | 10 +++++----- include/linux/device-mapper.h | 4 ++-- 8 files changed, 17 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/md/dm-crypt.c b/drivers/md/dm-crypt.c index 529e2ba505c3..ed1038164019 100644 --- a/drivers/md/dm-crypt.c +++ b/drivers/md/dm-crypt.c @@ -1318,7 +1318,7 @@ static int crypt_iterate_devices(struct dm_target *ti, { struct crypt_config *cc = ti->private; - return fn(ti, cc->dev, cc->start, data); + return fn(ti, cc->dev, cc->start, ti->len, data); } static struct target_type crypt_target = { diff --git a/drivers/md/dm-delay.c b/drivers/md/dm-delay.c index 4e5b843cd4d7..ebe7381f47c8 100644 --- a/drivers/md/dm-delay.c +++ b/drivers/md/dm-delay.c @@ -324,12 +324,12 @@ static int delay_iterate_devices(struct dm_target *ti, struct delay_c *dc = ti->private; int ret = 0; - ret = fn(ti, dc->dev_read, dc->start_read, data); + ret = fn(ti, dc->dev_read, dc->start_read, ti->len, data); if (ret) goto out; if (dc->dev_write) - ret = fn(ti, dc->dev_write, dc->start_write, data); + ret = fn(ti, dc->dev_write, dc->start_write, ti->len, data); out: return ret; diff --git a/drivers/md/dm-linear.c b/drivers/md/dm-linear.c index 9184b6deb868..82f7d6e6b1ea 100644 --- a/drivers/md/dm-linear.c +++ b/drivers/md/dm-linear.c @@ -139,7 +139,7 @@ static int linear_iterate_devices(struct dm_target *ti, { struct linear_c *lc = ti->private; - return fn(ti, lc->dev, lc->start, data); + return fn(ti, lc->dev, lc->start, ti->len, data); } static struct target_type linear_target = { diff --git a/drivers/md/dm-mpath.c b/drivers/md/dm-mpath.c index c70604a20897..6f0d90d4a541 100644 --- a/drivers/md/dm-mpath.c +++ b/drivers/md/dm-mpath.c @@ -1453,7 +1453,7 @@ static int multipath_iterate_devices(struct dm_target *ti, list_for_each_entry(pg, &m->priority_groups, list) { list_for_each_entry(p, &pg->pgpaths, list) { - ret = fn(ti, p->path.dev, ti->begin, data); + ret = fn(ti, p->path.dev, ti->begin, ti->len, data); if (ret) goto out; } diff --git a/drivers/md/dm-raid1.c b/drivers/md/dm-raid1.c index 42a3e4341d60..9726577cde49 100644 --- a/drivers/md/dm-raid1.c +++ b/drivers/md/dm-raid1.c @@ -1293,7 +1293,7 @@ static int mirror_iterate_devices(struct dm_target *ti, for (i = 0; !ret && i < ms->nr_mirrors; i++) ret = fn(ti, ms->mirror[i].dev, - ms->mirror[i].offset, data); + ms->mirror[i].offset, ti->len, data); return ret; } diff --git a/drivers/md/dm-stripe.c b/drivers/md/dm-stripe.c index b240e85ae39a..4e0e5937e42a 100644 --- a/drivers/md/dm-stripe.c +++ b/drivers/md/dm-stripe.c @@ -320,10 +320,11 @@ static int stripe_iterate_devices(struct dm_target *ti, int ret = 0; unsigned i = 0; - do + do { ret = fn(ti, sc->stripe[i].dev, - sc->stripe[i].physical_start, data); - while (!ret && ++i < sc->stripes); + sc->stripe[i].physical_start, + sc->stripe_width, data); + } while (!ret && ++i < sc->stripes); return ret; } diff --git a/drivers/md/dm-table.c b/drivers/md/dm-table.c index 5d16d06613aa..d952b3441913 100644 --- a/drivers/md/dm-table.c +++ b/drivers/md/dm-table.c @@ -346,7 +346,7 @@ static void close_dev(struct dm_dev_internal *d, struct mapped_device *md) * If possible, this checks an area of a destination device is valid. */ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data) + sector_t start, sector_t len, void *data) { struct queue_limits *limits = data; struct block_device *bdev = dev->bdev; @@ -359,7 +359,7 @@ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, if (!dev_size) return 1; - if ((start >= dev_size) || (start + ti->len > dev_size)) { + if ((start >= dev_size) || (start + len > dev_size)) { DMWARN("%s: %s too small for target", dm_device_name(ti->table->md), bdevname(bdev, b)); return 0; @@ -377,11 +377,11 @@ static int device_area_is_valid(struct dm_target *ti, struct dm_dev *dev, return 0; } - if (ti->len & (logical_block_size_sectors - 1)) { + if (len & (logical_block_size_sectors - 1)) { DMWARN("%s: len=%llu not aligned to h/w " "logical block size %hu of %s", dm_device_name(ti->table->md), - (unsigned long long)ti->len, + (unsigned long long)len, limits->logical_block_size, bdevname(bdev, b)); return 0; } @@ -482,7 +482,7 @@ static int __table_get_device(struct dm_table *t, struct dm_target *ti, #define min_not_zero(l, r) (l == 0) ? r : ((r == 0) ? l : min(l, r)) int dm_set_device_limits(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data) + sector_t start, sector_t len, void *data) { struct queue_limits *limits = data; struct block_device *bdev = dev->bdev; diff --git a/include/linux/device-mapper.h b/include/linux/device-mapper.h index 0d6310657f32..655e7721580a 100644 --- a/include/linux/device-mapper.h +++ b/include/linux/device-mapper.h @@ -84,7 +84,7 @@ typedef int (*dm_merge_fn) (struct dm_target *ti, struct bvec_merge_data *bvm, typedef int (*iterate_devices_callout_fn) (struct dm_target *ti, struct dm_dev *dev, - sector_t physical_start, + sector_t start, sector_t len, void *data); typedef int (*dm_iterate_devices_fn) (struct dm_target *ti, @@ -104,7 +104,7 @@ void dm_error(const char *message); * Combine device limits. */ int dm_set_device_limits(struct dm_target *ti, struct dm_dev *dev, - sector_t start, void *data); + sector_t start, sector_t len, void *data); struct dm_dev { struct block_device *bdev; -- cgit v1.2.3 From 8d406c6de2e67b5bae3c43b62b492c4ff63afb92 Mon Sep 17 00:00:00 2001 From: Felix Beck Date: Fri, 24 Jul 2009 12:39:53 +0200 Subject: [S390] zcrypt: fix scheduling of hrtimer ap_poll_timer Every time a request is enqueued or there is some work outstanding from the ap_tasklet, the ap_poll_timer is scheduled again. Unfortunately it was permanently called. It looked as if it was started in the past and thus imediately expired. This has been changed. First it is checked if the hrtimer is already expired. Then the expiring time is forwarded and the timer restarted. Signed-off-by: Felix Beck Signed-off-by: Martin Schwidefsky --- drivers/s390/crypto/ap_bus.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/crypto/ap_bus.c b/drivers/s390/crypto/ap_bus.c index 727a809636d8..ed3dcdea7fe1 100644 --- a/drivers/s390/crypto/ap_bus.c +++ b/drivers/s390/crypto/ap_bus.c @@ -1145,12 +1145,17 @@ ap_config_timeout(unsigned long ptr) */ static inline void ap_schedule_poll_timer(void) { + ktime_t hr_time; if (ap_using_interrupts() || ap_suspend_flag) return; if (hrtimer_is_queued(&ap_poll_timer)) return; - hrtimer_start(&ap_poll_timer, ktime_set(0, poll_timeout), - HRTIMER_MODE_ABS); + if (ktime_to_ns(hrtimer_expires_remaining(&ap_poll_timer)) <= 0) { + hr_time = ktime_set(0, poll_timeout); + hrtimer_forward_now(&ap_poll_timer, hr_time); + hrtimer_restart(&ap_poll_timer); + } + return; } /** -- cgit v1.2.3 From 36a516d953e02523e78ce27fbff91a968a9e5751 Mon Sep 17 00:00:00 2001 From: Erik Andrén Date: Tue, 23 Jun 2009 12:22:48 -0300 Subject: V4L/DVB (12221): gspca - stv06xx-hdcs: Actually update the sensor state MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index 3039ec208f3a..ec7f5536a8ad 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -174,7 +174,9 @@ static int hdcs_set_state(struct sd *sd, enum hdcs_power_state state) } ret = stv06xx_write_sensor(sd, HDCS_REG_CONTROL(sd), val); - if (ret < 0) + + /* Update the state if the write succeeded */ + if (!ret) hdcs->state = state; return ret; -- cgit v1.2.3 From ac51295ccc0ff922fea62cfc6f72cddf9c6c7306 Mon Sep 17 00:00:00 2001 From: Erik Andrén Date: Wed, 24 Jun 2009 04:30:56 -0300 Subject: V4L/DVB (12222): gspca - stv06xx-hdcs: Fix sensor sequence bug MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes. Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index ec7f5536a8ad..a45171be3f8c 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -131,9 +131,11 @@ static int hdcs_reg_write_seq(struct sd *sd, u8 reg, u8 *vals, u8 len) (reg + len > 0xff))) return -EINVAL; - for (i = 0; i < len; i++, reg++) { - regs[2*i] = reg; - regs[2*i+1] = vals[i]; + for (i = 0; i < len; i++) { + regs[2 * i] = reg; + regs[2 * i + 1] = vals[i]; + /* All addresses are shifted left one bit as bit 0 toggles r/w */ + reg += 2; } return stv06xx_write_sensor_bytes(sd, regs, len); -- cgit v1.2.3 From c0ea8f5b7264c813ee885f02b663ee3106f98afe Mon Sep 17 00:00:00 2001 From: Erik Andrén Date: Wed, 1 Jul 2009 02:56:44 -0300 Subject: V4L/DVB (12223): gspca - stv06xx-hdcs: Correct the pixelformat MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c index a45171be3f8c..e5024c8496ef 100644 --- a/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c +++ b/drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c @@ -64,7 +64,7 @@ static struct v4l2_pix_format hdcs1x00_mode[] = { { HDCS_1X00_DEF_WIDTH, HDCS_1X00_DEF_HEIGHT, - V4L2_PIX_FMT_SBGGR8, + V4L2_PIX_FMT_SGRBG8, V4L2_FIELD_NONE, .sizeimage = HDCS_1X00_DEF_WIDTH * HDCS_1X00_DEF_HEIGHT, @@ -80,7 +80,7 @@ static struct v4l2_pix_format hdcs1020_mode[] = { { HDCS_1020_DEF_WIDTH, HDCS_1020_DEF_HEIGHT, - V4L2_PIX_FMT_SBGGR8, + V4L2_PIX_FMT_SGRBG8, V4L2_FIELD_NONE, .sizeimage = HDCS_1020_DEF_WIDTH * HDCS_1020_DEF_HEIGHT, -- cgit v1.2.3 From 641f75caa874fffd679b64f850adee37103b0c0f Mon Sep 17 00:00:00 2001 From: Erik Andrén Date: Wed, 8 Jul 2009 14:47:16 -0300 Subject: V4L/DVB (12224): gspca - m5602-s5k4aa: Remove erroneous register writes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit A couple of erroneous register writes snuck in that made the image go haywire. Remove these. Many thanks to Grégory Lardière for finding this out Signed-off-by: Erik Andrén Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/m5602/m5602_s5k4aa.c | 6 ------ 1 file changed, 6 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/gspca/m5602/m5602_s5k4aa.c b/drivers/media/video/gspca/m5602/m5602_s5k4aa.c index 191bcd718979..0163903d1c0f 100644 --- a/drivers/media/video/gspca/m5602/m5602_s5k4aa.c +++ b/drivers/media/video/gspca/m5602/m5602_s5k4aa.c @@ -474,9 +474,6 @@ static int s5k4aa_set_vflip(struct gspca_dev *gspca_dev, __s32 val) PDEBUG(D_V4L2, "Set vertical flip to %d", val); err = m5602_write_sensor(sd, S5K4AA_PAGE_MAP, &data, 1); - if (err < 0) - return err; - err = m5602_write_sensor(sd, S5K4AA_READ_MODE, &data, 1); if (err < 0) return err; @@ -522,9 +519,6 @@ static int s5k4aa_set_hflip(struct gspca_dev *gspca_dev, __s32 val) PDEBUG(D_V4L2, "Set horizontal flip to %d", val); err = m5602_write_sensor(sd, S5K4AA_PAGE_MAP, &data, 1); - if (err < 0) - return err; - err = m5602_write_sensor(sd, S5K4AA_READ_MODE, &data, 1); if (err < 0) return err; -- cgit v1.2.3 From c43221df762c33e832e8855cae77989b6bf69fa6 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:23:23 -0300 Subject: V4L/DVB (12233): em28xx: rename is_27xx to is_webcam Just renames the flag, to use a clearer name. Later patches will use this flag to properly set some drivers behaviors for webcams. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ++-- drivers/media/video/em28xx/em28xx-core.c | 4 ++-- drivers/media/video/em28xx/em28xx-video.c | 4 ++-- drivers/media/video/em28xx/em28xx.h | 2 +- 4 files changed, 7 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index ebd24a25fb85..8f869468280f 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -450,7 +450,7 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_SILVERCREST_WEBCAM] = { .name = "Silvercrest Webcam 1.3mpix", .tuner_type = TUNER_ABSENT, - .is_27xx = 1, + .is_webcam = 1, .decoder = EM28XX_MT9V011, .input = { { .type = EM28XX_VMUX_COMPOSITE1, @@ -1772,7 +1772,7 @@ void em28xx_pre_card_setup(struct em28xx *dev) em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - if (dev->board.is_27xx) + if (dev->board.is_webcam) em28xx_info("chip is em2710\n"); else em28xx_info("chip ID is em2820\n"); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 079ab4d563a6..8649bdb7eb91 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -652,7 +652,7 @@ int em28xx_set_outfmt(struct em28xx *dev) outfmt = dev->format->reg; - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { vinmode = 0x0d; vinctl = 0x00; } else { @@ -707,7 +707,7 @@ static int em28xx_scaler_set(struct em28xx *dev, u16 h, u16 v) u8 mode; /* the em2800 scaler only supports scaling down to 50% */ - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { /* FIXME: Don't use the scaler yet */ mode = 0; } else if (dev->board.is_em2800) { diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 14316c912179..89ab2e3b9a2c 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -726,7 +726,7 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, return -EINVAL; } - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { /* FIXME: This is the only supported fmt */ width = 640; height = 480; @@ -768,7 +768,7 @@ static int em28xx_set_video_format(struct em28xx *dev, unsigned int fourcc, struct em28xx_fmt *fmt; /* FIXME: This is the only supported fmt */ - if (dev->board.is_27xx) { + if (dev->board.is_webcam) { width = 640; height = 480; } diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index d90fef463764..dc92e9ef85a4 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -390,7 +390,7 @@ struct em28xx_board { unsigned int max_range_640_480:1; unsigned int has_dvb:1; unsigned int has_snapshot_button:1; - unsigned int is_27xx:1; + unsigned int is_webcam:1; unsigned int valid:1; unsigned char xclk, i2c_speed; -- cgit v1.2.3 From 8a2e6990f44d4cebaafcc0af1a786912ae733bb2 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:26:36 -0300 Subject: V4L/DVB (12234): em28xx-cards: use is_webcam flag for devices that are known to be webcams By having the webcam devices marked as such, it will help the em28xx driver to do the right thing on those devices. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 8f869468280f..9e71f034665d 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -207,7 +207,8 @@ struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { .name = "Unknown EM2750/EM2751 webcam grabber", .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -239,7 +240,8 @@ struct em28xx_board em28xx_boards[] = { .name = "Huaqi DLCW-130", .valid = EM28XX_BOARD_NOT_VALIDATED, .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -440,7 +442,8 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_VIDEOLOGY_20K14XUSB] = { .name = "Videology 20K14XUSB USB2.0", .valid = EM28XX_BOARD_NOT_VALIDATED, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -500,7 +503,8 @@ struct em28xx_board em28xx_boards[] = { /* Beijing Huaqi Information Digital Technology Co., Ltd */ .name = "NetGMBH Cam", .valid = EM28XX_BOARD_NOT_VALIDATED, - .tuner_type = TUNER_ABSENT, /* This is a webcam */ + .tuner_type = TUNER_ABSENT, + .is_webcam = 1, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, -- cgit v1.2.3 From 8b220793d6fd309176438721088515be893630cd Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 10:56:21 -0300 Subject: V4L/DVB (12235): em28xx: detects sensors also with the generic em2750/2750 entry Webcams in general don't have eeprom. So, the sensor hint code should be called to properly detect what sensor is inside. Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.em28xx | 2 +- drivers/media/video/em28xx/em28xx-cards.c | 9 +++++---- 2 files changed, 6 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx index 014d255231fc..68c236c01846 100644 --- a/Documentation/video4linux/CARDLIST.em28xx +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -20,7 +20,7 @@ 19 -> EM2860/SAA711X Reference Design (em2860) 20 -> AMD ATI TV Wonder HD 600 (em2880) [0438:b002] 21 -> eMPIA Technology, Inc. GrabBeeX+ Video Encoder (em2800) [eb1a:2801] - 22 -> Unknown EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751] + 22 -> EM2710/EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751] 23 -> Huaqi DLCW-130 (em2750) 24 -> D-Link DUB-T210 TV Tuner (em2820/em2840) [2001:f112] 25 -> Gadmei UTV310 (em2820/em2840) diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 9e71f034665d..e64e1242a1ba 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -205,7 +205,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = { */ struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { - .name = "Unknown EM2750/EM2751 webcam grabber", + .name = "EM2710/EM2750/EM2751 webcam grabber", .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, .tuner_type = TUNER_ABSENT, .is_webcam = 1, @@ -1720,7 +1720,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; - if (dev->model != EM2820_BOARD_UNKNOWN) + if (dev->model != EM2820_BOARD_UNKNOWN && + dev->model != EM2750_BOARD_UNKNOWN) return 0; dev->i2c_client.addr = 0xba >> 1; @@ -1738,11 +1739,11 @@ static int em28xx_hint_sensor(struct em28xx *dev) sensor_name = "mt9v011"; break; default: - printk("Unknown Sensor 0x%04x\n", be16_to_cpu(version)); + printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); return -EINVAL; } - em28xx_errdev("Sensor is %s, assuming that webcam is %s\n", + em28xx_errdev("Sensor is %s, using model %s entry.\n", sensor_name, em28xx_boards[dev->model].name); return 0; -- cgit v1.2.3 From 527f09a981e398331c2f8d8f7af83cd46e6a06cc Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 12 Jul 2009 11:04:15 -0300 Subject: V4L/DVB (12236): em28xx: stop abusing of board->decoder for sensor information Instead of using em28xx board decoder field for storing sensor information, let's use instead a separate field for it. Also, as sensors are currently autodetected, there's no need of having it at the boards description. So, move it to the main em28xx struct. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ++-- drivers/media/video/em28xx/em28xx.h | 8 +++++++- 2 files changed, 9 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index e64e1242a1ba..530170ae0167 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -454,7 +454,6 @@ struct em28xx_board em28xx_boards[] = { .name = "Silvercrest Webcam 1.3mpix", .tuner_type = TUNER_ABSENT, .is_webcam = 1, - .decoder = EM28XX_MT9V011, .input = { { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, @@ -1737,6 +1736,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) case MT9V011_VERSION: dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; + dev->em28xx_sensor = EM28XX_MT9V011; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2267,7 +2267,7 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvp5150", "tvp5150", tvp5150_addrs); - if (dev->board.decoder == EM28XX_MT9V011) + if (dev->em28xx_sensor == EM28XX_MT9V011) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "mt9v011", "mt9v011", mt9v011_addrs); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index dc92e9ef85a4..655dd78cc07b 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -358,9 +358,13 @@ struct em28xx_input { #define INPUT(nr) (&em28xx_boards[dev->model].input[nr]) enum em28xx_decoder { - EM28XX_NODECODER, + EM28XX_NODECODER = 0, EM28XX_TVP5150, EM28XX_SAA711X, +}; + +enum em28xx_sensor { + EM28XX_NOSENSOR = 0, EM28XX_MT9V011, }; @@ -474,6 +478,8 @@ struct em28xx { struct v4l2_device v4l2_dev; struct em28xx_board board; + enum em28xx_sensor em28xx_sensor; + unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; unsigned int has_alsa_audio:1; -- cgit v1.2.3 From 9873740b2f41b37ec074afd4b8910b87dbebc0db Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 01:03:37 -0300 Subject: V4L/DVB (12237): mt9v011: implement VIDIOC_QUERYCTRL Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 1fe8fc9183a7..241382f5ba21 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -215,6 +215,23 @@ static int mt9v011_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) return -EINVAL; } +static int mt9v011_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qc) +{ + int i; + + v4l2_dbg(1, debug, sd, "queryctrl called\n"); + + for (i = 0; i < ARRAY_SIZE(mt9v011_qctrl); i++) + if (qc->id && qc->id == mt9v011_qctrl[i].id) { + memcpy(qc, &(mt9v011_qctrl[i]), + sizeof(*qc)); + return 0; + } + + return -EINVAL; +} + + static int mt9v011_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) { struct mt9v011 *core = to_mt9v011(sd); @@ -338,6 +355,7 @@ static int mt9v011_g_chip_ident(struct v4l2_subdev *sd, } static const struct v4l2_subdev_core_ops mt9v011_core_ops = { + .queryctrl = mt9v011_queryctrl, .g_ctrl = mt9v011_g_ctrl, .s_ctrl = mt9v011_s_ctrl, .reset = mt9v011_reset, -- cgit v1.2.3 From b04fb6615285d18df34ffd6cdd51db7a8a78dda0 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 01:28:21 -0300 Subject: V4L/DVB (12238): em28xx: call sensor detection code for all webcam entries With the previous approach, autodetection were working only for the two generic entries (em275x and em2820 unknown ones). So, if someone would try to force probing an specific device, the code would not properly run the autodetection code. With the new approach, the sensor autodetection will be run not only for the two generic entries, but also do webcam specific ones. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 530170ae0167..1318766b35bb 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -234,6 +234,7 @@ struct em28xx_board em28xx_boards[] = { [EM2820_BOARD_UNKNOWN] = { .name = "Unknown EM2750/28xx video grabber", .tuner_type = TUNER_ABSENT, + .is_webcam = 1, /* To enable sensor probe */ }, [EM2750_BOARD_DLCW_130] = { /* Beijing Huaqi Information Digital Technology Co., Ltd */ @@ -1719,10 +1720,6 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; - if (dev->model != EM2820_BOARD_UNKNOWN && - dev->model != EM2750_BOARD_UNKNOWN) - return 0; - dev->i2c_client.addr = 0xba >> 1; cmd = 0; i2c_master_send(&dev->i2c_client, &cmd, 1); @@ -1777,10 +1774,7 @@ void em28xx_pre_card_setup(struct em28xx *dev) em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - if (dev->board.is_webcam) - em28xx_info("chip is em2710\n"); - else - em28xx_info("chip ID is em2820\n"); + em28xx_info("chip ID is em2710 or em2820\n"); break; case CHIP_ID_EM2840: em28xx_info("chip ID is em2840\n"); @@ -2415,7 +2409,13 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, return errCode; } - em28xx_hint_sensor(dev); + /* + * If the device can be a webcam, seek for a sensor. + * If sensor is not found, then it isn't a webcam. + */ + if (dev->board.is_webcam) + if (em28xx_hint_sensor(dev) < 0) + dev->board.is_webcam = 0; /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); -- cgit v1.2.3 From 5569996421fa1cfc1fc0d9e683ac1def46ea985d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 13 Jul 2009 20:15:02 -0300 Subject: V4L/DVB (12239): em28xx: fix webcam scaling While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do work with em28xx + webcam. The issue is that the scaling setup depends on the number of visible rows/cols of the input image. With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling is different from a normal TV image (720x480 on NTSC). This were causing a wrong scaling and a previous patch disabled scaling. As each sensor have their different resolution setting, the xres/yres should be adjusted accordingly with the input sensor. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 6 +++--- drivers/media/video/em28xx/em28xx-core.c | 5 +---- drivers/media/video/em28xx/em28xx-video.c | 16 +++------------- drivers/media/video/em28xx/em28xx.h | 15 +++++++++++---- 4 files changed, 18 insertions(+), 24 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 1318766b35bb..d4a7e6075cc9 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -58,8 +58,6 @@ static unsigned int card[] = {[0 ... (EM28XX_MAXBOARDS - 1)] = UNSET }; module_param_array(card, int, NULL, 0444); MODULE_PARM_DESC(card, "card type"); -#define MT9V011_VERSION 0x8243 - /* Bitmask marking allocated devices from 0 to EM28XX_MAXBOARDS */ static unsigned long em28xx_devused; @@ -1730,10 +1728,12 @@ static int em28xx_hint_sensor(struct em28xx *dev) version = be16_to_cpu(version_be); switch (version) { - case MT9V011_VERSION: + case 0x8243: /* mt9v011 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; + dev->sensor_xres = 640; + dev->sensor_yres = 480; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 8649bdb7eb91..c7fcce713945 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -707,10 +707,7 @@ static int em28xx_scaler_set(struct em28xx *dev, u16 h, u16 v) u8 mode; /* the em2800 scaler only supports scaling down to 50% */ - if (dev->board.is_webcam) { - /* FIXME: Don't use the scaler yet */ - mode = 0; - } else if (dev->board.is_em2800) { + if (dev->board.is_em2800) { mode = (v ? 0x20 : 0x00) | (h ? 0x10 : 0x00); } else { u8 buf[2]; diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 89ab2e3b9a2c..ff37b4c15f44 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -657,8 +657,8 @@ static void get_scale(struct em28xx *dev, unsigned int width, unsigned int height, unsigned int *hscale, unsigned int *vscale) { - unsigned int maxw = norm_maxw(dev); - unsigned int maxh = norm_maxh(dev); + unsigned int maxw = norm_maxw(dev); + unsigned int maxh = norm_maxh(dev); *hscale = (((unsigned long)maxw) << 12) / width - 4096L; if (*hscale >= 0x4000) @@ -726,11 +726,7 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, return -EINVAL; } - if (dev->board.is_webcam) { - /* FIXME: This is the only supported fmt */ - width = 640; - height = 480; - } else if (dev->board.is_em2800) { + if (dev->board.is_em2800) { /* the em2800 can only scale down to 50% */ height = height > (3 * maxh / 4) ? maxh : maxh / 2; width = width > (3 * maxw / 4) ? maxw : maxw / 2; @@ -767,12 +763,6 @@ static int em28xx_set_video_format(struct em28xx *dev, unsigned int fourcc, { struct em28xx_fmt *fmt; - /* FIXME: This is the only supported fmt */ - if (dev->board.is_webcam) { - width = 640; - height = 480; - } - fmt = format_by_fourcc(fourcc); if (!fmt) return -EINVAL; diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 655dd78cc07b..71444ddbe40c 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -479,6 +479,7 @@ struct em28xx { struct em28xx_board board; enum em28xx_sensor em28xx_sensor; + int sensor_xres, sensor_yres; unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; @@ -760,17 +761,23 @@ static inline int em28xx_gamma_set(struct em28xx *dev, s32 val) /*FIXME: maxw should be dependent of alt mode */ static inline unsigned int norm_maxw(struct em28xx *dev) { + if (dev->board.is_webcam) + return dev->sensor_xres; + if (dev->board.max_range_640_480) return 640; - else - return 720; + + return 720; } static inline unsigned int norm_maxh(struct em28xx *dev) { + if (dev->board.is_webcam) + return dev->sensor_yres; + if (dev->board.max_range_640_480) return 480; - else - return (dev->norm & V4L2_STD_625_50) ? 576 : 480; + + return (dev->norm & V4L2_STD_625_50) ? 576 : 480; } #endif -- cgit v1.2.3 From e11206e67f738b04d0c508795adc9bff504bc875 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 02:38:18 -0300 Subject: V4L/DVB (12240): mt9v011: add a function to calculate frames per second rate It is possible to adjust the fps rate by changing some register values. This is function of the connected Xtal at the camera sensor, being a 27 MHz cristal needed, in order to support 640x480 at 30 fps. For now, it will only calculate the values for fps. Later patches may introduce V4L2 ioctls, to allow frequency rate adjustments. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 32 +++++++++++++++++++++++++++++++- 1 file changed, 31 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 241382f5ba21..f7b5279a7d5a 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -8,6 +8,7 @@ #include #include #include +#include #include #include "mt9v011.h" #include @@ -57,6 +58,7 @@ static struct v4l2_queryctrl mt9v011_qctrl[] = { struct mt9v011 { struct v4l2_subdev sd; unsigned width, height; + unsigned xtal; u16 global_gain, red_bal, blue_bal; }; @@ -131,7 +133,7 @@ static const struct i2c_reg_value mt9v011_init_default[] = { { R1E_MT9V011_DIGITAL_ZOOM, 0x0000 }, { R20_MT9V011_READ_MODE, 0x1000 }, - { R07_MT9V011_OUT_CTRL, 0x000a }, /* chip enable */ + { R07_MT9V011_OUT_CTRL, 0x0002 }, /* chip enable */ }; static void set_balance(struct v4l2_subdev *sd) @@ -154,6 +156,31 @@ static void set_balance(struct v4l2_subdev *sd) mt9v011_write(sd, R2D_MT9V011_RED_GAIN, red_gain); } +static void calc_fps(struct v4l2_subdev *sd) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned height, width, hblank, vblank, speed; + unsigned row_time, t_time; + u64 frames_per_ms; + unsigned tmp; + + height = mt9v011_read(sd, R03_MT9V011_HEIGHT); + width = mt9v011_read(sd, R04_MT9V011_WIDTH); + hblank = mt9v011_read(sd, R05_MT9V011_HBLANK); + vblank = mt9v011_read(sd, R06_MT9V011_VBLANK); + speed = mt9v011_read(sd, R0A_MT9V011_CLK_SPEED); + + row_time = (width + 113 + hblank) * (speed + 2); + t_time = row_time * (height + vblank + 1); + + frames_per_ms = core->xtal * 1000l; + do_div(frames_per_ms, t_time); + tmp = frames_per_ms; + + v4l2_dbg(1, debug, sd, "Programmed to %u.%03u fps (%d pixel clcks)\n", + tmp / 1000, tmp % 1000, t_time); +} + static void set_res(struct v4l2_subdev *sd) { struct mt9v011 *core = to_mt9v011(sd); @@ -179,6 +206,8 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R01_MT9V011_ROWSTART, vstart); mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); + + calc_fps(sd); }; static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) @@ -413,6 +442,7 @@ static int mt9v011_probe(struct i2c_client *c, core->global_gain = 0x0024; core->width = 640; core->height = 480; + core->xtal = 27000000; /* Hz */ v4l_info(c, "chip found @ 0x%02x (%s)\n", c->addr << 1, c->adapter->name); -- cgit v1.2.3 From c180604a87c5abb0a117998009d01a4499d58653 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 02:39:19 -0300 Subject: V4L/DVB (12241): mt9v011: Fix vstart vstart calculus were wrong. Fix it. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index f7b5279a7d5a..d7b15dd836e6 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -202,7 +202,7 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R04_MT9V011_WIDTH, core->width); mt9v011_write(sd, R05_MT9V011_HBLANK, 771 - core->width); - vstart = 8 + (640 - core->height) / 2; + vstart = 8 + (480 - core->height) / 2; mt9v011_write(sd, R01_MT9V011_ROWSTART, vstart); mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); -- cgit v1.2.3 From 2ea472ff704a8a94b3b9abec438db23e512be337 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 03:14:21 -0300 Subject: V4L/DVB (12242): mt9v011: implement core->s_config to allow adjusting xtal frequency Since frames per second is a function of cristal frequency, and this is device-specific, add a function that allows adjusting it, via subdev->core->s_config callback. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index d7b15dd836e6..b2260de645f0 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -340,6 +340,22 @@ static int mt9v011_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) return 0; } +static int mt9v011_s_config(struct v4l2_subdev *sd, int dumb, void *data) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned *xtal = data; + + v4l2_dbg(1, debug, sd, "s_config called\n"); + + if (xtal) { + core->xtal = *xtal; + v4l2_dbg(1, debug, sd, "xtal set to %d.%03d MHz\n", + *xtal / 1000000, (*xtal / 1000) % 1000); + } + + return 0; +} + #ifdef CONFIG_VIDEO_ADV_DEBUG static int mt9v011_g_register(struct v4l2_subdev *sd, @@ -388,6 +404,7 @@ static const struct v4l2_subdev_core_ops mt9v011_core_ops = { .g_ctrl = mt9v011_g_ctrl, .s_ctrl = mt9v011_s_ctrl, .reset = mt9v011_reset, + .s_config = mt9v011_s_config, .g_chip_ident = mt9v011_g_chip_ident, #ifdef CONFIG_VIDEO_ADV_DEBUG .g_register = mt9v011_g_register, -- cgit v1.2.3 From d36bb4e77257ed0df86deca3f69794f037f68c7d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 03:18:39 -0300 Subject: V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency In order to properly estimate fps, mt9v011 sensor driver needs to know what is the used frequency on the sensor cristal. Adds the proper fields and initialization code for specifying the cristal frequency. Also, based on experimentation, it was noticed that the Silvercrest is outputing data at 7 fps. This means that it should be using a 6.3 MHz cristal. This information needs to be double checked later, by opening the device. Anyway, by using this value for xtal, at least now we have the correct fps report. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 11 ++++++++--- drivers/media/video/em28xx/em28xx.h | 2 ++ 2 files changed, 10 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index d4a7e6075cc9..82536dd6b0fd 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1734,6 +1734,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; + dev->sensor_xtal = 6300000; break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2261,9 +2262,13 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvp5150", "tvp5150", tvp5150_addrs); - if (dev->em28xx_sensor == EM28XX_MT9V011) - v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap, - "mt9v011", "mt9v011", mt9v011_addrs); + if (dev->em28xx_sensor == EM28XX_MT9V011) { + struct v4l2_subdev *sd; + + sd = v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, + &dev->i2c_adap, "mt9v011", "mt9v011", mt9v011_addrs); + v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal); + } if (dev->board.adecoder == EM28XX_TVAUDIO) v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap, diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 71444ddbe40c..ce76633786c8 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -478,8 +478,10 @@ struct em28xx { struct v4l2_device v4l2_dev; struct em28xx_board board; + /* Webcam specific fields */ enum em28xx_sensor em28xx_sensor; int sensor_xres, sensor_yres; + int sensor_xtal; unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; -- cgit v1.2.3 From 579d315218e8a3f696e375c5f6917da6488bec8a Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 12:33:25 -0300 Subject: V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format Depending on the video input format, vinmode/vinctl needs adjustments. For TV, this is not relevant, since the supported decoders output data at the same format. However, webcam sensors may have different formats, so, this needs to be adjusted based on the device. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 11 +++++++++++ drivers/media/video/em28xx/em28xx-core.c | 17 +++-------------- drivers/media/video/em28xx/em28xx.h | 3 +++ 3 files changed, 17 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 82536dd6b0fd..e793aee16726 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1735,6 +1735,11 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->sensor_xres = 640; dev->sensor_yres = 480; dev->sensor_xtal = 6300000; + + /* probably means GRGB 16 bit bayer */ + dev->vinmode = 0x0d; + dev->vinctl = 0x00; + break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2414,6 +2419,12 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, return errCode; } + /* + * Default format, used for tvp5150 or saa711x output formats + */ + dev->vinmode = 0x10; + dev->vinctl = 0x11; + /* * If the device can be a webcam, seek for a sensor. * If sensor is not found, then it isn't a webcam. diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index c7fcce713945..5b78e199abd1 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -648,28 +648,17 @@ int em28xx_capture_start(struct em28xx *dev, int start) int em28xx_set_outfmt(struct em28xx *dev) { int ret; - int vinmode, vinctl, outfmt; - - outfmt = dev->format->reg; - - if (dev->board.is_webcam) { - vinmode = 0x0d; - vinctl = 0x00; - } else { - vinmode = 0x10; - vinctl = 0x11; - } ret = em28xx_write_reg_bits(dev, EM28XX_R27_OUTFMT, - outfmt | 0x20, 0xff); + dev->format->reg | 0x20, 0xff); if (ret < 0) return ret; - ret = em28xx_write_reg(dev, EM28XX_R10_VINMODE, vinmode); + ret = em28xx_write_reg(dev, EM28XX_R10_VINMODE, dev->vinmode); if (ret < 0) return ret; - return em28xx_write_reg(dev, EM28XX_R11_VINCTRL, vinctl); + return em28xx_write_reg(dev, EM28XX_R11_VINCTRL, dev->vinctl); } static int em28xx_accumulator_set(struct em28xx *dev, u8 xmin, u8 xmax, diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index ce76633786c8..766ab59b8d59 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -483,6 +483,9 @@ struct em28xx { int sensor_xres, sensor_yres; int sensor_xtal; + /* Vinmode/Vinctl used at the driver */ + int vinmode, vinctl; + unsigned int stream_on:1; /* Locks streams */ unsigned int has_audio_class:1; unsigned int has_alsa_audio:1; -- cgit v1.2.3 From b80fd2d811b48a92051f86d257b00f373e69a6d7 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 14 Jul 2009 21:08:22 -0300 Subject: V4L/DVB (12245): em28xx: add support for mt9m001 webcams Thanks to Wally for bringing the issue and helping with the tests. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 41 +++++++++++++++++++++++++++++++ drivers/media/video/em28xx/em28xx.h | 1 + 2 files changed, 42 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index e793aee16726..1bd789a52e63 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -211,6 +211,7 @@ struct em28xx_board em28xx_boards[] = { .type = EM28XX_VMUX_COMPOSITE1, .vmux = 0, .amux = EM28XX_AMUX_VIDEO, + .gpio = silvercrest_reg_seq, } }, }, [EM2800_BOARD_UNKNOWN] = { @@ -1706,6 +1707,32 @@ static inline void em28xx_set_model(struct em28xx *dev) EM28XX_I2C_FREQ_100_KHZ; } +/* FIXME: Should be replaced by a proper mt9m001 driver */ +static int em28xx_initialize_mt9m001(struct em28xx *dev) +{ + int i; + unsigned char regs[][3] = { + { 0x0d, 0x00, 0x01, }, + { 0x0d, 0x00, 0x00, }, + { 0x04, 0x05, 0x00, }, /* hres = 1280 */ + { 0x03, 0x04, 0x00, }, /* vres = 1024 */ + { 0x20, 0x11, 0x00, }, + { 0x06, 0x00, 0x10, }, + { 0x2b, 0x00, 0x24, }, + { 0x2e, 0x00, 0x24, }, + { 0x35, 0x00, 0x24, }, + { 0x2d, 0x00, 0x20, }, + { 0x2c, 0x00, 0x20, }, + { 0x09, 0x0a, 0xd4, }, + { 0x35, 0x00, 0x57, }, + }; + + for (i = 0; i < ARRAY_SIZE(regs); i++) + i2c_master_send(&dev->i2c_client, ®s[i][0], 3); + + return 0; +} + /* HINT method: webcam I2C chips * * This method work for webcams with Micron sensors @@ -1740,6 +1767,19 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->vinmode = 0x0d; dev->vinctl = 0x00; + break; + case 0x8431: + dev->model = EM2750_BOARD_UNKNOWN; + sensor_name = "mt9m001"; + dev->em28xx_sensor = EM28XX_MT9M001; + em28xx_initialize_mt9m001(dev); + dev->sensor_xres = 1280; + dev->sensor_yres = 1024; + + /* probably means BGGR 16 bit bayer */ + dev->vinmode = 0x0c; + dev->vinctl = 0x00; + break; default: printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version)); @@ -2275,6 +2315,7 @@ void em28xx_card_setup(struct em28xx *dev) v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal); } + if (dev->board.adecoder == EM28XX_TVAUDIO) v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap, "tvaudio", "tvaudio", dev->board.tvaudio_addr); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 766ab59b8d59..45bd513f62dc 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -366,6 +366,7 @@ enum em28xx_decoder { enum em28xx_sensor { EM28XX_NOSENSOR = 0, EM28XX_MT9V011, + EM28XX_MT9M001, }; enum em28xx_adecoder { -- cgit v1.2.3 From 4fb202a8d9d936f7080ab631140b447a0625e36c Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 17:51:12 -0300 Subject: V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant) The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add support for the MT352 variant. Thanks to Jelle de Jong for providing a unit to test/debug with. Cc: Jelle de Jong Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 47 ++++++++++++++++++++++++++++----- 1 file changed, 41 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index 3da97c32b8fa..d57f7583ac66 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -31,6 +31,8 @@ #include "lgdt330x.h" #include "zl10353.h" #include "s5h1409.h" +#include "mt352.h" +#include "mt352_priv.h" /* FIXME */ MODULE_DESCRIPTION("driver for em28xx based DVB cards"); MODULE_AUTHOR("Mauro Carvalho Chehab "); @@ -258,6 +260,41 @@ static struct drx397xD_config em28xx_drx397xD_with_xc3028 = { }; #endif +static int mt352_terratec_xs_init(struct dvb_frontend *fe) +{ + /* Values extracted from a USB trace of the Terratec Windows driver */ + static u8 clock_config[] = { CLOCK_CTL, 0x38, 0x2c }; + static u8 reset[] = { RESET, 0x80 }; + static u8 adc_ctl_1_cfg[] = { ADC_CTL_1, 0x40 }; + static u8 agc_cfg[] = { AGC_TARGET, 0x28, 0xa0 }; + static u8 input_freq_cfg[] = { INPUT_FREQ_1, 0x31, 0xb8 }; + static u8 rs_err_cfg[] = { RS_ERR_PER_1, 0x00, 0x4d }; + static u8 capt_range_cfg[] = { CAPT_RANGE, 0x32 }; + static u8 trl_nom_cfg[] = { TRL_NOMINAL_RATE_1, 0x64, 0x00 }; + static u8 tps_given_cfg[] = { TPS_GIVEN_1, 0x40, 0x80, 0x50 }; + static u8 tuner_go[] = { TUNER_GO, 0x5d}; + + mt352_write(fe, clock_config, sizeof(clock_config)); + udelay(200); + mt352_write(fe, reset, sizeof(reset)); + mt352_write(fe, adc_ctl_1_cfg, sizeof(adc_ctl_1_cfg)); + mt352_write(fe, agc_cfg, sizeof(agc_cfg)); + mt352_write(fe, input_freq_cfg, sizeof(input_freq_cfg)); + mt352_write(fe, rs_err_cfg, sizeof(rs_err_cfg)); + mt352_write(fe, capt_range_cfg, sizeof(capt_range_cfg)); + mt352_write(fe, trl_nom_cfg, sizeof(trl_nom_cfg)); + mt352_write(fe, tps_given_cfg, sizeof(tps_given_cfg)); + mt352_write(fe, tuner_go, sizeof(tuner_go)); + return 0; +} + +static struct mt352_config terratec_xs_mt352_cfg = { + .demod_address = (0x1e >> 1), + .no_tuner = 1, + .if2 = 45600, + .demod_init = mt352_terratec_xs_init, +}; + /* ------------------------------------------------------------------ */ static int attach_xc3028(u8 addr, struct em28xx *dev) @@ -458,13 +495,11 @@ static int dvb_init(struct em28xx *dev) if (dvb->frontend == NULL) { /* This board could have either a zl10353 or a mt352. If the chip id isn't for zl10353, try mt352 */ - - /* FIXME: make support for mt352 work */ - printk(KERN_ERR "version of this board with mt352 not " - "currently supported\n"); - result = -EINVAL; - goto out_free; + dvb->frontend = dvb_attach(mt352_attach, + &terratec_xs_mt352_cfg, + &dev->i2c_adap); } + if (attach_xc3028(0x61, dev) < 0) { result = -EINVAL; goto out_free; -- cgit v1.2.3 From ff69786b4ccd0d5b99a60ba0be98237f9b7d8f52 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 18:44:19 -0300 Subject: V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB Andy walls pointed out that we were passing 0x5d to the TUNER_GO register, instead of 0x01. Set the register properly (note the code did still work with the incorrect value, so this does not address a regression). Thanks to Andy Walls for noticing the issue. Cc: Andy Walls Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index d57f7583ac66..f3f0e8fe73c6 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -272,7 +272,7 @@ static int mt352_terratec_xs_init(struct dvb_frontend *fe) static u8 capt_range_cfg[] = { CAPT_RANGE, 0x32 }; static u8 trl_nom_cfg[] = { TRL_NOMINAL_RATE_1, 0x64, 0x00 }; static u8 tps_given_cfg[] = { TPS_GIVEN_1, 0x40, 0x80, 0x50 }; - static u8 tuner_go[] = { TUNER_GO, 0x5d}; + static u8 tuner_go[] = { TUNER_GO, 0x01}; mt352_write(fe, clock_config, sizeof(clock_config)); udelay(200); -- cgit v1.2.3 From d5b3ba9cb375620a109d79f2e3a7bc21e9b75d8f Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 8 Jul 2009 21:51:35 -0300 Subject: V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881) Setup the GPIOs properly and enable support for the DVB side of the Pinnacle Hybrid Pro USB stick. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 24 ++++++++++++++++++++---- drivers/media/video/em28xx/em28xx-dvb.c | 1 + 2 files changed, 21 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 1bd789a52e63..ba20065c24b1 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -157,6 +157,20 @@ static struct em28xx_reg_seq evga_indtube_digital[] = { { -1, -1, -1, -1}, }; +/* Pinnacle Hybrid Pro eb1a:2881 */ +static struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = { + {EM28XX_R08_GPIO, 0x6f, ~EM_GPIO_4, 10}, + { -1, -1, -1, -1}, +}; + +static struct em28xx_reg_seq pinnacle_hybrid_pro_digital[] = { + {EM28XX_R08_GPIO, 0x6e, ~EM_GPIO_4, 10}, + {EM2880_R04_GPO, 0x04, 0xff, 100},/* zl10353 reset */ + {EM2880_R04_GPO, 0x0c, 0xff, 1}, + { -1, -1, -1, -1}, +}; + + /* Callback for the most boards */ static struct em28xx_reg_seq default_tuner_gpio[] = { {EM28XX_R08_GPIO, EM_GPIO_4, EM_GPIO_4, 10}, @@ -1253,25 +1267,26 @@ struct em28xx_board em28xx_boards[] = { }, [EM2881_BOARD_PINNACLE_HYBRID_PRO] = { .name = "Pinnacle Hybrid Pro", - .valid = EM28XX_BOARD_NOT_VALIDATED, .tuner_type = TUNER_XC2028, .tuner_gpio = default_tuner_gpio, .decoder = EM28XX_TVP5150, + .has_dvb = 1, + .dvb_gpio = pinnacle_hybrid_pro_digital, .input = { { .type = EM28XX_VMUX_TELEVISION, .vmux = TVP5150_COMPOSITE0, .amux = EM28XX_AMUX_VIDEO, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_COMPOSITE1, .vmux = TVP5150_COMPOSITE1, .amux = EM28XX_AMUX_LINE_IN, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_SVIDEO, .vmux = TVP5150_SVIDEO, .amux = EM28XX_AMUX_LINE_IN, - .gpio = default_analog, + .gpio = pinnacle_hybrid_pro_analog, } }, }, [EM2882_BOARD_PINNACLE_HYBRID_PRO] = { @@ -1641,6 +1656,7 @@ static struct em28xx_hash_table em28xx_eeprom_hash[] = { {0x966a0441, EM2880_BOARD_KWORLD_DVB_310U, TUNER_XC2028}, {0x9567eb1a, EM2880_BOARD_EMPIRE_DUAL_TV, TUNER_XC2028}, {0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028}, + {0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028}, }; /* I2C devicelist hash table for devices with generic USB IDs */ diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index f3f0e8fe73c6..5ebc274c1b2f 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -489,6 +489,7 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_TERRATEC_HYBRID_XS: + case EM2881_BOARD_PINNACLE_HYBRID_PRO: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_terratec_xs_zl10353_xc3028, &dev->i2c_adap); -- cgit v1.2.3 From 44010440ca2693a07b1252ee836a23804412575e Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 8 Jul 2009 22:18:15 -0300 Subject: V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else the emp202 doesn't get detected properly. Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index ba20065c24b1..476acb02a3d3 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -159,7 +159,7 @@ static struct em28xx_reg_seq evga_indtube_digital[] = { /* Pinnacle Hybrid Pro eb1a:2881 */ static struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = { - {EM28XX_R08_GPIO, 0x6f, ~EM_GPIO_4, 10}, + {EM28XX_R08_GPIO, 0xfd, ~EM_GPIO_4, 10}, { -1, -1, -1, -1}, }; -- cgit v1.2.3 From 5343e446014b93f740d5502f9f3bfa3f66dcbc7c Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 15 Jul 2009 00:35:47 -0300 Subject: V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used In cases where the device has a generic Empia USB ID, the call in the precard setup phase did not set the tuner GPIO. As a result, the tuner may not be taken out of reset before attempting initialization in the analog driver. This problem was not seen before with the EVGA inDtube, since that particular board has the analog GPIO setup to include taking the tuner out of reset. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment for the Pinnacle 320e. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 476acb02a3d3..5aef7ddd091c 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2286,6 +2286,7 @@ void em28xx_card_setup(struct em28xx *dev) em28xx_set_mode() in em28xx_pre_card_setup() was a no-op, so make the call now so the analog GPIOs are set properly before probing the i2c bus. */ + em28xx_gpio_set(dev, dev->board.tuner_gpio); em28xx_set_mode(dev, EM28XX_ANALOG_MODE); break; case EM2820_BOARD_SILVERCREST_WEBCAM: -- cgit v1.2.3 From e16e5a3739cfd208de00d49def10fcfa6ceff46f Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Wed, 15 Jul 2009 00:37:22 -0300 Subject: V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which is required for digital tuning to work properly. Add the missing profile. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 5aef7ddd091c..320f1f60276e 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1990,6 +1990,7 @@ static void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl) ctl->demod = XC3028_FE_ZARLINK456; break; case EM2880_BOARD_TERRATEC_HYBRID_XS: + case EM2881_BOARD_PINNACLE_HYBRID_PRO: ctl->demod = XC3028_FE_ZARLINK456; break; case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2: -- cgit v1.2.3 From a84f79aed688a94197387830df3a2f2068f49dc0 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Sun, 12 Jul 2009 17:05:02 -0300 Subject: V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1) When the change was introduced in the zl10353 for the i2c gate behavior, this broke the HVR-900 which was not behind a gate. Use a version of the zl10353 config profile that indicates the tuner is not behind such a gate. Without this patch the first tune succeeds, but subsequent tuning attempts will fail. The change also renames the terratec zl10353 profile I wrote to be more generic, since it is shared by the non-terratec device. Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test with. Cc: Michael Krufky Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index 5ebc274c1b2f..cf0ac7f2a30d 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -245,7 +245,7 @@ static struct s5h1409_config em28xx_s5h1409_with_xc3028 = { .mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK }; -static struct zl10353_config em28xx_terratec_xs_zl10353_xc3028 = { +static struct zl10353_config em28xx_zl10353_xc3028_no_i2c_gate = { .demod_address = (0x1e >> 1), .no_tuner = 1, .disable_i2c_gate_ctrl = 1, @@ -477,7 +477,6 @@ static int dvb_init(struct em28xx *dev) goto out_free; } break; - case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: case EM2880_BOARD_KWORLD_DVB_310U: case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, @@ -488,10 +487,19 @@ static int dvb_init(struct em28xx *dev) goto out_free; } break; + case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: + dvb->frontend = dvb_attach(zl10353_attach, + &em28xx_zl10353_xc3028_no_i2c_gate, + &dev->i2c_adap); + if (attach_xc3028(0x61, dev) < 0) { + result = -EINVAL; + goto out_free; + } + break; case EM2880_BOARD_TERRATEC_HYBRID_XS: case EM2881_BOARD_PINNACLE_HYBRID_PRO: dvb->frontend = dvb_attach(zl10353_attach, - &em28xx_terratec_xs_zl10353_xc3028, + &em28xx_zl10353_xc3028_no_i2c_gate, &dev->i2c_adap); if (dvb->frontend == NULL) { /* This board could have either a zl10353 or a mt352. -- cgit v1.2.3 From 27954930f047df73a16253db2750345034e56c40 Mon Sep 17 00:00:00 2001 From: Jean-Francois Moine Date: Wed, 8 Jul 2009 05:21:50 -0300 Subject: V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors. The bug was introduced when adding the light frequency control Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/sonixj.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/gspca/sonixj.c b/drivers/media/video/gspca/sonixj.c index 0d02f41fa7d0..bad309b90cce 100644 --- a/drivers/media/video/gspca/sonixj.c +++ b/drivers/media/video/gspca/sonixj.c @@ -1634,6 +1634,8 @@ static void setfreq(struct gspca_dev *gspca_dev) { struct sd *sd = (struct sd *) gspca_dev; + if (gspca_dev->ctrl_dis & (1 << FREQ_IDX)) + return; if (sd->sensor == SENSOR_OV7660) { switch (sd->freq) { case 0: /* Banding filter disabled */ -- cgit v1.2.3 From a2f5a8117cb185fc347f35e369a6320e6aa9d82d Mon Sep 17 00:00:00 2001 From: Antti Palosaari Date: Fri, 10 Jul 2009 20:03:43 -0300 Subject: V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app Request demodulator auto-detect transmission parameters in case of garbage parameters provided by application for compatibility. That's needed at least for MPlayer compatibility currently. Thanks to Jelle de Jong for reporting issue and providing SSH access to Devin for debugging. Thanks to Devin Heitmueller for hard debug work he did to find that bug. Cc: Devin Heitmueller Cc: Jelle de Jong Signed-off-by: Antti Palosaari Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/frontends/af9013.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/media/dvb/frontends/af9013.c b/drivers/media/dvb/frontends/af9013.c index 136c5863d81b..12e018b4107d 100644 --- a/drivers/media/dvb/frontends/af9013.c +++ b/drivers/media/dvb/frontends/af9013.c @@ -527,6 +527,10 @@ static int af9013_set_ofdm_params(struct af9013_state *state, u8 i, buf[3] = {0, 0, 0}; *auto_mode = 0; /* set if parameters are requested to auto set */ + /* Try auto-detect transmission parameters in case of AUTO requested or + garbage parameters given by application for compatibility. + MPlayer seems to provide garbage parameters currently. */ + switch (params->transmission_mode) { case TRANSMISSION_MODE_AUTO: *auto_mode = 1; @@ -536,7 +540,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (1 << 0); break; default: - return -EINVAL; + deb_info("%s: invalid transmission_mode\n", __func__); + *auto_mode = 1; } switch (params->guard_interval) { @@ -554,7 +559,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (3 << 2); break; default: - return -EINVAL; + deb_info("%s: invalid guard_interval\n", __func__); + *auto_mode = 1; } switch (params->hierarchy_information) { @@ -572,7 +578,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[0] |= (3 << 4); break; default: - return -EINVAL; + deb_info("%s: invalid hierarchy_information\n", __func__); + *auto_mode = 1; }; switch (params->constellation) { @@ -587,7 +594,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[1] |= (2 << 6); break; default: - return -EINVAL; + deb_info("%s: invalid constellation\n", __func__); + *auto_mode = 1; } /* Use HP. How and which case we can switch to LP? */ @@ -611,7 +619,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[2] |= (4 << 0); break; default: - return -EINVAL; + deb_info("%s: invalid code_rate_HP\n", __func__); + *auto_mode = 1; } switch (params->code_rate_LP) { @@ -638,7 +647,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, if (params->hierarchy_information == HIERARCHY_AUTO) break; default: - return -EINVAL; + deb_info("%s: invalid code_rate_LP\n", __func__); + *auto_mode = 1; } switch (params->bandwidth) { @@ -651,7 +661,8 @@ static int af9013_set_ofdm_params(struct af9013_state *state, buf[1] |= (2 << 2); break; default: - return -EINVAL; + deb_info("%s: invalid bandwidth\n", __func__); + buf[1] |= (2 << 2); /* cannot auto-detect BW, try 8 MHz */ } /* program */ -- cgit v1.2.3 From af1d9afa75082663ea9e2b67b9381d1af403f52b Mon Sep 17 00:00:00 2001 From: Brian Johnson Date: Sun, 19 Jul 2009 05:29:20 -0300 Subject: V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register. Signed-off-by: Brian Johnson Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/gspca.c | 73 +++++++++++++++++++++++++++++++++++++++ drivers/media/video/gspca/gspca.h | 9 +++++ 2 files changed, 82 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/gspca/gspca.c b/drivers/media/video/gspca/gspca.c index 1e89600986c8..b8561dfb6c8c 100644 --- a/drivers/media/video/gspca/gspca.c +++ b/drivers/media/video/gspca/gspca.c @@ -727,6 +727,74 @@ static int gspca_get_mode(struct gspca_dev *gspca_dev, return -EINVAL; } +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int vidioc_g_register(struct file *file, void *priv, + struct v4l2_dbg_register *reg) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (!gspca_dev->sd_desc->get_register) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->get_register(gspca_dev, reg); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} + +static int vidioc_s_register(struct file *file, void *priv, + struct v4l2_dbg_register *reg) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (!gspca_dev->sd_desc->set_register) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->set_register(gspca_dev, reg); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} +#endif + +static int vidioc_g_chip_ident(struct file *file, void *priv, + struct v4l2_dbg_chip_ident *chip) +{ + int ret; + struct gspca_dev *gspca_dev = priv; + + if (!gspca_dev->sd_desc->get_chip_ident) + return -EINVAL; + + if (mutex_lock_interruptible(&gspca_dev->usb_lock)) + return -ERESTARTSYS; + if (gspca_dev->present) + ret = gspca_dev->sd_desc->get_chip_ident(gspca_dev, chip); + else + ret = -ENODEV; + mutex_unlock(&gspca_dev->usb_lock); + + return ret; +} + static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv, struct v4l2_fmtdesc *fmtdesc) { @@ -1883,6 +1951,11 @@ static const struct v4l2_ioctl_ops dev_ioctl_ops = { .vidioc_s_parm = vidioc_s_parm, .vidioc_s_std = vidioc_s_std, .vidioc_enum_framesizes = vidioc_enum_framesizes, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .vidioc_g_register = vidioc_g_register, + .vidioc_s_register = vidioc_s_register, +#endif + .vidioc_g_chip_ident = vidioc_g_chip_ident, #ifdef CONFIG_VIDEO_V4L1_COMPAT .vidiocgmbuf = vidiocgmbuf, #endif diff --git a/drivers/media/video/gspca/gspca.h b/drivers/media/video/gspca/gspca.h index bd1faff88644..46c4effdfcd5 100644 --- a/drivers/media/video/gspca/gspca.h +++ b/drivers/media/video/gspca/gspca.h @@ -69,6 +69,10 @@ typedef void (*cam_v_op) (struct gspca_dev *); typedef int (*cam_cf_op) (struct gspca_dev *, const struct usb_device_id *); typedef int (*cam_jpg_op) (struct gspca_dev *, struct v4l2_jpegcompression *); +typedef int (*cam_reg_op) (struct gspca_dev *, + struct v4l2_dbg_register *); +typedef int (*cam_ident_op) (struct gspca_dev *, + struct v4l2_dbg_chip_ident *); typedef int (*cam_streamparm_op) (struct gspca_dev *, struct v4l2_streamparm *); typedef int (*cam_qmnu_op) (struct gspca_dev *, @@ -105,6 +109,11 @@ struct sd_desc { cam_qmnu_op querymenu; cam_streamparm_op get_streamparm; cam_streamparm_op set_streamparm; +#ifdef CONFIG_VIDEO_ADV_DEBUG + cam_reg_op set_register; + cam_reg_op get_register; +#endif + cam_ident_op get_chip_ident; }; /* packet types when moving from iso buf to frame buf */ -- cgit v1.2.3 From 26e744b6b61066203fd57de0d3962353621e06f8 Mon Sep 17 00:00:00 2001 From: Brian Johnson Date: Sun, 19 Jul 2009 05:52:58 -0300 Subject: V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges. Signed-off-by: Brian Johnson Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/gspca.txt | 32 + drivers/media/video/gspca/Kconfig | 16 + drivers/media/video/gspca/Makefile | 2 + drivers/media/video/gspca/sn9c20x.c | 2433 +++++++++++++++++++++++++++++++++++ include/linux/videodev2.h | 1 + include/media/v4l2-chip-ident.h | 12 + 6 files changed, 2496 insertions(+) create mode 100644 drivers/media/video/gspca/sn9c20x.c (limited to 'drivers') diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt index 2bcf78896e22..573f95b58807 100644 --- a/Documentation/video4linux/gspca.txt +++ b/Documentation/video4linux/gspca.txt @@ -44,7 +44,9 @@ zc3xx 0458:7007 Genius VideoCam V2 zc3xx 0458:700c Genius VideoCam V3 zc3xx 0458:700f Genius VideoCam Web V2 sonixj 0458:7025 Genius Eye 311Q +sn9c20x 0458:7029 Genius Look 320s sonixj 0458:702e Genius Slim 310 NB +sn9c20x 045e:00f4 LifeCam VX-6000 (SN9C20x + OV9650) sonixj 045e:00f5 MicroSoft VX3000 sonixj 045e:00f7 MicroSoft VX1000 ov519 045e:028c Micro$oft xbox cam @@ -282,6 +284,28 @@ sonixj 0c45:613a Microdia Sonix PC Camera sonixj 0c45:613b Surfer SN-206 sonixj 0c45:613c Sonix Pccam168 sonixj 0c45:6143 Sonix Pccam168 +sn9c20x 0c45:6240 PC Camera (SN9C201 + MT9M001) +sn9c20x 0c45:6242 PC Camera (SN9C201 + MT9M111) +sn9c20x 0c45:6248 PC Camera (SN9C201 + OV9655) +sn9c20x 0c45:624e PC Camera (SN9C201 + SOI968) +sn9c20x 0c45:624f PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6251 PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6253 PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6260 PC Camera (SN9C201 + OV7670) +sn9c20x 0c45:6270 PC Camera (SN9C201 + MT9V011/MT9V111/MT9V112) +sn9c20x 0c45:627b PC Camera (SN9C201 + OV7660) +sn9c20x 0c45:627c PC Camera (SN9C201 + HV7131R) +sn9c20x 0c45:627f PC Camera (SN9C201 + OV9650) +sn9c20x 0c45:6280 PC Camera (SN9C202 + MT9M001) +sn9c20x 0c45:6282 PC Camera (SN9C202 + MT9M111) +sn9c20x 0c45:6288 PC Camera (SN9C202 + OV9655) +sn9c20x 0c45:628e PC Camera (SN9C202 + SOI968) +sn9c20x 0c45:628f PC Camera (SN9C202 + OV9650) +sn9c20x 0c45:62a0 PC Camera (SN9C202 + OV7670) +sn9c20x 0c45:62b0 PC Camera (SN9C202 + MT9V011/MT9V111/MT9V112) +sn9c20x 0c45:62b3 PC Camera (SN9C202 + OV9655) +sn9c20x 0c45:62bb PC Camera (SN9C202 + OV7660) +sn9c20x 0c45:62bc PC Camera (SN9C202 + HV7131R) sunplus 0d64:0303 Sunplus FashionCam DXG etoms 102c:6151 Qcam Sangha CIF etoms 102c:6251 Qcam xxxxxx VGA @@ -290,6 +314,7 @@ spca561 10fd:7e50 FlyCam Usb 100 zc3xx 10fd:8050 Typhoon Webshot II USB 300k ov534 1415:2000 Sony HD Eye for PS3 (SLEH 00201) pac207 145f:013a Trust WB-1300N +sn9c20x 145f:013d Trust WB-3600R vc032x 15b8:6001 HP 2.0 Megapixel vc032x 15b8:6002 HP 2.0 Megapixel rz406aa spca501 1776:501c Arowana 300K CMOS Camera @@ -300,4 +325,11 @@ spca500 2899:012c Toptro Industrial spca508 8086:0110 Intel Easy PC Camera spca500 8086:0630 Intel Pocket PC Camera spca506 99fa:8988 Grandtec V.cap +sn9c20x a168:0610 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0611 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0613 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0618 Dino-Lite Digital Microscope (SN9C201 + HV7131R) +sn9c20x a168:0614 Dino-Lite Digital Microscope (SN9C201 + MT9M111) +sn9c20x a168:0615 Dino-Lite Digital Microscope (SN9C201 + MT9M111) +sn9c20x a168:0617 Dino-Lite Digital Microscope (SN9C201 + MT9M111) spca561 abcd:cdee Petcam diff --git a/drivers/media/video/gspca/Kconfig b/drivers/media/video/gspca/Kconfig index 578dc4ffc965..34f46f2bc040 100644 --- a/drivers/media/video/gspca/Kconfig +++ b/drivers/media/video/gspca/Kconfig @@ -102,6 +102,22 @@ config USB_GSPCA_PAC7311 To compile this driver as a module, choose M here: the module will be called gspca_pac7311. +config USB_GSPCA_SN9C20X + tristate "SN9C20X USB Camera Driver" + depends on VIDEO_V4L2 && USB_GSPCA + help + Say Y here if you want support for cameras based on the + sn9c20x chips (SN9C201 and SN9C202). + + To compile this driver as a module, choose M here: the + module will be called gspca_sn9c20x. + +config USB_GSPCA_SN9C20X_EVDEV + bool "Enable evdev support" + depends on USB_GSPCA_SN9C20X + ---help--- + Say Y here in order to enable evdev support for sn9c20x webcam button. + config USB_GSPCA_SONIXB tristate "SONIX Bayer USB Camera Driver" depends on VIDEO_V4L2 && USB_GSPCA diff --git a/drivers/media/video/gspca/Makefile b/drivers/media/video/gspca/Makefile index 8a6643e8eb96..f6d3b86e9ad5 100644 --- a/drivers/media/video/gspca/Makefile +++ b/drivers/media/video/gspca/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_USB_GSPCA_OV519) += gspca_ov519.o obj-$(CONFIG_USB_GSPCA_OV534) += gspca_ov534.o obj-$(CONFIG_USB_GSPCA_PAC207) += gspca_pac207.o obj-$(CONFIG_USB_GSPCA_PAC7311) += gspca_pac7311.o +obj-$(CONFIG_USB_GSPCA_SN9C20X) += gspca_sn9c20x.o obj-$(CONFIG_USB_GSPCA_SONIXB) += gspca_sonixb.o obj-$(CONFIG_USB_GSPCA_SONIXJ) += gspca_sonixj.o obj-$(CONFIG_USB_GSPCA_SPCA500) += gspca_spca500.o @@ -35,6 +36,7 @@ gspca_ov519-objs := ov519.o gspca_ov534-objs := ov534.o gspca_pac207-objs := pac207.o gspca_pac7311-objs := pac7311.o +gspca_sn9c20x-objs := sn9c20x.o gspca_sonixb-objs := sonixb.o gspca_sonixj-objs := sonixj.o gspca_spca500-objs := spca500.o diff --git a/drivers/media/video/gspca/sn9c20x.c b/drivers/media/video/gspca/sn9c20x.c new file mode 100644 index 000000000000..78ab26ceb90e --- /dev/null +++ b/drivers/media/video/gspca/sn9c20x.c @@ -0,0 +1,2433 @@ +/* + * Sonix sn9c201 sn9c202 library + * Copyright (C) 2008-2009 microdia project + * Copyright (C) 2009 Brian Johnson + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include "gspca.h" +#include "jpeg.h" + +#include +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV +#include +#include +#include +#include +#endif + +MODULE_AUTHOR("Brian Johnson , " + "microdia project "); +MODULE_DESCRIPTION("GSPCA/SN9C20X USB Camera Driver"); +MODULE_LICENSE("GPL"); + +#define MODULE_NAME "sn9c20x" + +#define MODE_RAW 0x10 +#define MODE_JPEG 0x20 +#define MODE_SXGA 0x80 + +#define SENSOR_OV9650 0 +#define SENSOR_OV9655 1 +#define SENSOR_SOI968 2 +#define SENSOR_OV7660 3 +#define SENSOR_OV7670 4 +#define SENSOR_MT9V011 5 +#define SENSOR_MT9V111 6 +#define SENSOR_MT9V112 7 +#define SENSOR_MT9M001 8 +#define SENSOR_MT9M111 9 +#define SENSOR_HV7131R 10 +#define SENSOR_MT9VPRB 20 + +/* specific webcam descriptor */ +struct sd { + struct gspca_dev gspca_dev; + +#define MIN_AVG_LUM 80 +#define MAX_AVG_LUM 130 + atomic_t avg_lum; + u8 old_step; + u8 older_step; + u8 exposure_step; + + u8 brightness; + u8 contrast; + u8 saturation; + s16 hue; + u8 gamma; + u8 red; + u8 blue; + + u8 hflip; + u8 vflip; + u8 gain; + u16 exposure; + u8 auto_exposure; + + u8 i2c_addr; + u8 sensor; + u8 hstart; + u8 vstart; + + u8 *jpeg_hdr; + u8 quality; + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + struct input_dev *input_dev; + u8 input_gpio; + struct task_struct *input_task; +#endif +}; + +static int sd_setbrightness(struct gspca_dev *gspca_dev, s32 val); +static int sd_getbrightness(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setcontrast(struct gspca_dev *gspca_dev, s32 val); +static int sd_getcontrast(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setsaturation(struct gspca_dev *gspca_dev, s32 val); +static int sd_getsaturation(struct gspca_dev *gspca_dev, s32 *val); +static int sd_sethue(struct gspca_dev *gspca_dev, s32 val); +static int sd_gethue(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setgamma(struct gspca_dev *gspca_dev, s32 val); +static int sd_getgamma(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setredbalance(struct gspca_dev *gspca_dev, s32 val); +static int sd_getredbalance(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setbluebalance(struct gspca_dev *gspca_dev, s32 val); +static int sd_getbluebalance(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setvflip(struct gspca_dev *gspca_dev, s32 val); +static int sd_getvflip(struct gspca_dev *gspca_dev, s32 *val); +static int sd_sethflip(struct gspca_dev *gspca_dev, s32 val); +static int sd_gethflip(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setgain(struct gspca_dev *gspca_dev, s32 val); +static int sd_getgain(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setexposure(struct gspca_dev *gspca_dev, s32 val); +static int sd_getexposure(struct gspca_dev *gspca_dev, s32 *val); +static int sd_setautoexposure(struct gspca_dev *gspca_dev, s32 val); +static int sd_getautoexposure(struct gspca_dev *gspca_dev, s32 *val); + +static struct ctrl sd_ctrls[] = { + { +#define BRIGHTNESS_IDX 0 + { + .id = V4L2_CID_BRIGHTNESS, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Brightness", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define BRIGHTNESS_DEFAULT 0x7f + .default_value = BRIGHTNESS_DEFAULT, + }, + .set = sd_setbrightness, + .get = sd_getbrightness, + }, + { +#define CONTRAST_IDX 1 + { + .id = V4L2_CID_CONTRAST, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Contrast", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define CONTRAST_DEFAULT 0x7f + .default_value = CONTRAST_DEFAULT, + }, + .set = sd_setcontrast, + .get = sd_getcontrast, + }, + { +#define SATURATION_IDX 2 + { + .id = V4L2_CID_SATURATION, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Saturation", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define SATURATION_DEFAULT 0x7f + .default_value = SATURATION_DEFAULT, + }, + .set = sd_setsaturation, + .get = sd_getsaturation, + }, + { +#define HUE_IDX 3 + { + .id = V4L2_CID_HUE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Hue", + .minimum = -180, + .maximum = 180, + .step = 1, +#define HUE_DEFAULT 0 + .default_value = HUE_DEFAULT, + }, + .set = sd_sethue, + .get = sd_gethue, + }, + { +#define GAMMA_IDX 4 + { + .id = V4L2_CID_GAMMA, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gamma", + .minimum = 0, + .maximum = 0xff, + .step = 1, +#define GAMMA_DEFAULT 0x10 + .default_value = GAMMA_DEFAULT, + }, + .set = sd_setgamma, + .get = sd_getgamma, + }, + { +#define BLUE_IDX 5 + { + .id = V4L2_CID_BLUE_BALANCE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Blue Balance", + .minimum = 0, + .maximum = 0x7f, + .step = 1, +#define BLUE_DEFAULT 0x28 + .default_value = BLUE_DEFAULT, + }, + .set = sd_setbluebalance, + .get = sd_getbluebalance, + }, + { +#define RED_IDX 6 + { + .id = V4L2_CID_RED_BALANCE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Red Balance", + .minimum = 0, + .maximum = 0x7f, + .step = 1, +#define RED_DEFAULT 0x28 + .default_value = RED_DEFAULT, + }, + .set = sd_setredbalance, + .get = sd_getredbalance, + }, + { +#define HFLIP_IDX 7 + { + .id = V4L2_CID_HFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Horizontal Flip", + .minimum = 0, + .maximum = 1, + .step = 1, +#define HFLIP_DEFAULT 0 + .default_value = HFLIP_DEFAULT, + }, + .set = sd_sethflip, + .get = sd_gethflip, + }, + { +#define VFLIP_IDX 8 + { + .id = V4L2_CID_VFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Vertical Flip", + .minimum = 0, + .maximum = 1, + .step = 1, +#define VFLIP_DEFAULT 0 + .default_value = VFLIP_DEFAULT, + }, + .set = sd_setvflip, + .get = sd_getvflip, + }, + { +#define EXPOSURE_IDX 9 + { + .id = V4L2_CID_EXPOSURE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Exposure", + .minimum = 0, + .maximum = 0x1780, + .step = 1, +#define EXPOSURE_DEFAULT 0x33 + .default_value = EXPOSURE_DEFAULT, + }, + .set = sd_setexposure, + .get = sd_getexposure, + }, + { +#define GAIN_IDX 10 + { + .id = V4L2_CID_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain", + .minimum = 0, + .maximum = 28, + .step = 1, +#define GAIN_DEFAULT 0x00 + .default_value = GAIN_DEFAULT, + }, + .set = sd_setgain, + .get = sd_getgain, + }, + { +#define AUTOGAIN_IDX 11 + { + .id = V4L2_CID_AUTOGAIN, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Auto Exposure", + .minimum = 0, + .maximum = 1, + .step = 1, +#define AUTO_EXPOSURE_DEFAULT 1 + .default_value = AUTO_EXPOSURE_DEFAULT, + }, + .set = sd_setautoexposure, + .get = sd_getautoexposure, + }, +}; + +static const struct v4l2_pix_format vga_mode[] = { + {160, 120, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 0 | MODE_JPEG}, + {160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 160, + .sizeimage = 160 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0 | MODE_RAW}, + {160, 120, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0}, + {320, 240, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 1 | MODE_JPEG}, + {320, 240, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 320, + .sizeimage = 320 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1 | MODE_RAW}, + {320, 240, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1}, + {640, 480, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 2 | MODE_JPEG}, + {640, 480, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 640, + .sizeimage = 640 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2 | MODE_RAW}, + {640, 480, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2}, +}; + +static const struct v4l2_pix_format sxga_mode[] = { + {160, 120, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 0 | MODE_JPEG}, + {160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 160, + .sizeimage = 160 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0 | MODE_RAW}, + {160, 120, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 240, + .sizeimage = 240 * 120, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 0}, + {320, 240, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 1 | MODE_JPEG}, + {320, 240, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 320, + .sizeimage = 320 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1 | MODE_RAW}, + {320, 240, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 480, + .sizeimage = 480 * 240 , + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 1}, + {640, 480, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_JPEG, + .priv = 2 | MODE_JPEG}, + {640, 480, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 640, + .sizeimage = 640 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2 | MODE_RAW}, + {640, 480, V4L2_PIX_FMT_SN9C20X_I420, V4L2_FIELD_NONE, + .bytesperline = 960, + .sizeimage = 960 * 480, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 2}, + {1280, 1024, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, + .bytesperline = 1280, + .sizeimage = (1280 * 1024) + 64, + .colorspace = V4L2_COLORSPACE_SRGB, + .priv = 3 | MODE_RAW | MODE_SXGA}, +}; + +static const int hsv_red_x[] = { + 41, 44, 46, 48, 50, 52, 54, 56, + 58, 60, 62, 64, 66, 68, 70, 72, + 74, 76, 78, 80, 81, 83, 85, 87, + 88, 90, 92, 93, 95, 97, 98, 100, + 101, 102, 104, 105, 107, 108, 109, 110, + 112, 113, 114, 115, 116, 117, 118, 119, + 120, 121, 122, 123, 123, 124, 125, 125, + 126, 127, 127, 128, 128, 129, 129, 129, + 130, 130, 130, 130, 131, 131, 131, 131, + 131, 131, 131, 131, 130, 130, 130, 130, + 129, 129, 129, 128, 128, 127, 127, 126, + 125, 125, 124, 123, 122, 122, 121, 120, + 119, 118, 117, 116, 115, 114, 112, 111, + 110, 109, 107, 106, 105, 103, 102, 101, + 99, 98, 96, 94, 93, 91, 90, 88, + 86, 84, 83, 81, 79, 77, 75, 74, + 72, 70, 68, 66, 64, 62, 60, 58, + 56, 54, 52, 49, 47, 45, 43, 41, + 39, 36, 34, 32, 30, 28, 25, 23, + 21, 19, 16, 14, 12, 9, 7, 5, + 3, 0, -1, -3, -6, -8, -10, -12, + -15, -17, -19, -22, -24, -26, -28, -30, + -33, -35, -37, -39, -41, -44, -46, -48, + -50, -52, -54, -56, -58, -60, -62, -64, + -66, -68, -70, -72, -74, -76, -78, -80, + -81, -83, -85, -87, -88, -90, -92, -93, + -95, -97, -98, -100, -101, -102, -104, -105, + -107, -108, -109, -110, -112, -113, -114, -115, + -116, -117, -118, -119, -120, -121, -122, -123, + -123, -124, -125, -125, -126, -127, -127, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -127, -127, -126, -125, -125, -124, -123, + -122, -122, -121, -120, -119, -118, -117, -116, + -115, -114, -112, -111, -110, -109, -107, -106, + -105, -103, -102, -101, -99, -98, -96, -94, + -93, -91, -90, -88, -86, -84, -83, -81, + -79, -77, -75, -74, -72, -70, -68, -66, + -64, -62, -60, -58, -56, -54, -52, -49, + -47, -45, -43, -41, -39, -36, -34, -32, + -30, -28, -25, -23, -21, -19, -16, -14, + -12, -9, -7, -5, -3, 0, 1, 3, + 6, 8, 10, 12, 15, 17, 19, 22, + 24, 26, 28, 30, 33, 35, 37, 39, 41 +}; + +static const int hsv_red_y[] = { + 82, 80, 78, 76, 74, 73, 71, 69, + 67, 65, 63, 61, 58, 56, 54, 52, + 50, 48, 46, 44, 41, 39, 37, 35, + 32, 30, 28, 26, 23, 21, 19, 16, + 14, 12, 10, 7, 5, 3, 0, -1, + -3, -6, -8, -10, -13, -15, -17, -19, + -22, -24, -26, -29, -31, -33, -35, -38, + -40, -42, -44, -46, -48, -51, -53, -55, + -57, -59, -61, -63, -65, -67, -69, -71, + -73, -75, -77, -79, -81, -82, -84, -86, + -88, -89, -91, -93, -94, -96, -98, -99, + -101, -102, -104, -105, -106, -108, -109, -110, + -112, -113, -114, -115, -116, -117, -119, -120, + -120, -121, -122, -123, -124, -125, -126, -126, + -127, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -128, -128, -128, -128, -128, -128, -128, -128, + -127, -127, -126, -125, -125, -124, -123, -122, + -121, -120, -119, -118, -117, -116, -115, -114, + -113, -111, -110, -109, -107, -106, -105, -103, + -102, -100, -99, -97, -96, -94, -92, -91, + -89, -87, -85, -84, -82, -80, -78, -76, + -74, -73, -71, -69, -67, -65, -63, -61, + -58, -56, -54, -52, -50, -48, -46, -44, + -41, -39, -37, -35, -32, -30, -28, -26, + -23, -21, -19, -16, -14, -12, -10, -7, + -5, -3, 0, 1, 3, 6, 8, 10, + 13, 15, 17, 19, 22, 24, 26, 29, + 31, 33, 35, 38, 40, 42, 44, 46, + 48, 51, 53, 55, 57, 59, 61, 63, + 65, 67, 69, 71, 73, 75, 77, 79, + 81, 82, 84, 86, 88, 89, 91, 93, + 94, 96, 98, 99, 101, 102, 104, 105, + 106, 108, 109, 110, 112, 113, 114, 115, + 116, 117, 119, 120, 120, 121, 122, 123, + 124, 125, 126, 126, 127, 128, 128, 129, + 129, 130, 130, 131, 131, 131, 131, 132, + 132, 132, 132, 132, 132, 132, 132, 132, + 132, 132, 132, 131, 131, 131, 130, 130, + 130, 129, 129, 128, 127, 127, 126, 125, + 125, 124, 123, 122, 121, 120, 119, 118, + 117, 116, 115, 114, 113, 111, 110, 109, + 107, 106, 105, 103, 102, 100, 99, 97, + 96, 94, 92, 91, 89, 87, 85, 84, 82 +}; + +static const int hsv_green_x[] = { + -124, -124, -125, -125, -125, -125, -125, -125, + -125, -126, -126, -125, -125, -125, -125, -125, + -125, -124, -124, -124, -123, -123, -122, -122, + -121, -121, -120, -120, -119, -118, -117, -117, + -116, -115, -114, -113, -112, -111, -110, -109, + -108, -107, -105, -104, -103, -102, -100, -99, + -98, -96, -95, -93, -92, -91, -89, -87, + -86, -84, -83, -81, -79, -77, -76, -74, + -72, -70, -69, -67, -65, -63, -61, -59, + -57, -55, -53, -51, -49, -47, -45, -43, + -41, -39, -37, -35, -33, -30, -28, -26, + -24, -22, -20, -18, -15, -13, -11, -9, + -7, -4, -2, 0, 1, 3, 6, 8, + 10, 12, 14, 17, 19, 21, 23, 25, + 27, 29, 32, 34, 36, 38, 40, 42, + 44, 46, 48, 50, 52, 54, 56, 58, + 60, 62, 64, 66, 68, 70, 71, 73, + 75, 77, 78, 80, 82, 83, 85, 87, + 88, 90, 91, 93, 94, 96, 97, 98, + 100, 101, 102, 104, 105, 106, 107, 108, + 109, 111, 112, 113, 113, 114, 115, 116, + 117, 118, 118, 119, 120, 120, 121, 122, + 122, 123, 123, 124, 124, 124, 125, 125, + 125, 125, 125, 125, 125, 126, 126, 125, + 125, 125, 125, 125, 125, 124, 124, 124, + 123, 123, 122, 122, 121, 121, 120, 120, + 119, 118, 117, 117, 116, 115, 114, 113, + 112, 111, 110, 109, 108, 107, 105, 104, + 103, 102, 100, 99, 98, 96, 95, 93, + 92, 91, 89, 87, 86, 84, 83, 81, + 79, 77, 76, 74, 72, 70, 69, 67, + 65, 63, 61, 59, 57, 55, 53, 51, + 49, 47, 45, 43, 41, 39, 37, 35, + 33, 30, 28, 26, 24, 22, 20, 18, + 15, 13, 11, 9, 7, 4, 2, 0, + -1, -3, -6, -8, -10, -12, -14, -17, + -19, -21, -23, -25, -27, -29, -32, -34, + -36, -38, -40, -42, -44, -46, -48, -50, + -52, -54, -56, -58, -60, -62, -64, -66, + -68, -70, -71, -73, -75, -77, -78, -80, + -82, -83, -85, -87, -88, -90, -91, -93, + -94, -96, -97, -98, -100, -101, -102, -104, + -105, -106, -107, -108, -109, -111, -112, -113, + -113, -114, -115, -116, -117, -118, -118, -119, + -120, -120, -121, -122, -122, -123, -123, -124, -124 +}; + +static const int hsv_green_y[] = { + -100, -99, -98, -97, -95, -94, -93, -91, + -90, -89, -87, -86, -84, -83, -81, -80, + -78, -76, -75, -73, -71, -70, -68, -66, + -64, -63, -61, -59, -57, -55, -53, -51, + -49, -48, -46, -44, -42, -40, -38, -36, + -34, -32, -30, -27, -25, -23, -21, -19, + -17, -15, -13, -11, -9, -7, -4, -2, + 0, 1, 3, 5, 7, 9, 11, 14, + 16, 18, 20, 22, 24, 26, 28, 30, + 32, 34, 36, 38, 40, 42, 44, 46, + 48, 50, 52, 54, 56, 58, 59, 61, + 63, 65, 67, 68, 70, 72, 74, 75, + 77, 78, 80, 82, 83, 85, 86, 88, + 89, 90, 92, 93, 95, 96, 97, 98, + 100, 101, 102, 103, 104, 105, 106, 107, + 108, 109, 110, 111, 112, 112, 113, 114, + 115, 115, 116, 116, 117, 117, 118, 118, + 119, 119, 119, 120, 120, 120, 120, 120, + 121, 121, 121, 121, 121, 121, 120, 120, + 120, 120, 120, 119, 119, 119, 118, 118, + 117, 117, 116, 116, 115, 114, 114, 113, + 112, 111, 111, 110, 109, 108, 107, 106, + 105, 104, 103, 102, 100, 99, 98, 97, + 95, 94, 93, 91, 90, 89, 87, 86, + 84, 83, 81, 80, 78, 76, 75, 73, + 71, 70, 68, 66, 64, 63, 61, 59, + 57, 55, 53, 51, 49, 48, 46, 44, + 42, 40, 38, 36, 34, 32, 30, 27, + 25, 23, 21, 19, 17, 15, 13, 11, + 9, 7, 4, 2, 0, -1, -3, -5, + -7, -9, -11, -14, -16, -18, -20, -22, + -24, -26, -28, -30, -32, -34, -36, -38, + -40, -42, -44, -46, -48, -50, -52, -54, + -56, -58, -59, -61, -63, -65, -67, -68, + -70, -72, -74, -75, -77, -78, -80, -82, + -83, -85, -86, -88, -89, -90, -92, -93, + -95, -96, -97, -98, -100, -101, -102, -103, + -104, -105, -106, -107, -108, -109, -110, -111, + -112, -112, -113, -114, -115, -115, -116, -116, + -117, -117, -118, -118, -119, -119, -119, -120, + -120, -120, -120, -120, -121, -121, -121, -121, + -121, -121, -120, -120, -120, -120, -120, -119, + -119, -119, -118, -118, -117, -117, -116, -116, + -115, -114, -114, -113, -112, -111, -111, -110, + -109, -108, -107, -106, -105, -104, -103, -102, -100 +}; + +static const int hsv_blue_x[] = { + 112, 113, 114, 114, 115, 116, 117, 117, + 118, 118, 119, 119, 120, 120, 120, 121, + 121, 121, 122, 122, 122, 122, 122, 122, + 122, 122, 122, 122, 122, 122, 121, 121, + 121, 120, 120, 120, 119, 119, 118, 118, + 117, 116, 116, 115, 114, 113, 113, 112, + 111, 110, 109, 108, 107, 106, 105, 104, + 103, 102, 100, 99, 98, 97, 95, 94, + 93, 91, 90, 88, 87, 85, 84, 82, + 80, 79, 77, 76, 74, 72, 70, 69, + 67, 65, 63, 61, 60, 58, 56, 54, + 52, 50, 48, 46, 44, 42, 40, 38, + 36, 34, 32, 30, 28, 26, 24, 22, + 19, 17, 15, 13, 11, 9, 7, 5, + 2, 0, -1, -3, -5, -7, -9, -12, + -14, -16, -18, -20, -22, -24, -26, -28, + -31, -33, -35, -37, -39, -41, -43, -45, + -47, -49, -51, -53, -54, -56, -58, -60, + -62, -64, -66, -67, -69, -71, -73, -74, + -76, -78, -79, -81, -83, -84, -86, -87, + -89, -90, -92, -93, -94, -96, -97, -98, + -99, -101, -102, -103, -104, -105, -106, -107, + -108, -109, -110, -111, -112, -113, -114, -114, + -115, -116, -117, -117, -118, -118, -119, -119, + -120, -120, -120, -121, -121, -121, -122, -122, + -122, -122, -122, -122, -122, -122, -122, -122, + -122, -122, -121, -121, -121, -120, -120, -120, + -119, -119, -118, -118, -117, -116, -116, -115, + -114, -113, -113, -112, -111, -110, -109, -108, + -107, -106, -105, -104, -103, -102, -100, -99, + -98, -97, -95, -94, -93, -91, -90, -88, + -87, -85, -84, -82, -80, -79, -77, -76, + -74, -72, -70, -69, -67, -65, -63, -61, + -60, -58, -56, -54, -52, -50, -48, -46, + -44, -42, -40, -38, -36, -34, -32, -30, + -28, -26, -24, -22, -19, -17, -15, -13, + -11, -9, -7, -5, -2, 0, 1, 3, + 5, 7, 9, 12, 14, 16, 18, 20, + 22, 24, 26, 28, 31, 33, 35, 37, + 39, 41, 43, 45, 47, 49, 51, 53, + 54, 56, 58, 60, 62, 64, 66, 67, + 69, 71, 73, 74, 76, 78, 79, 81, + 83, 84, 86, 87, 89, 90, 92, 93, + 94, 96, 97, 98, 99, 101, 102, 103, + 104, 105, 106, 107, 108, 109, 110, 111, 112 +}; + +static const int hsv_blue_y[] = { + -11, -13, -15, -17, -19, -21, -23, -25, + -27, -29, -31, -33, -35, -37, -39, -41, + -43, -45, -46, -48, -50, -52, -54, -55, + -57, -59, -61, -62, -64, -66, -67, -69, + -71, -72, -74, -75, -77, -78, -80, -81, + -83, -84, -86, -87, -88, -90, -91, -92, + -93, -95, -96, -97, -98, -99, -100, -101, + -102, -103, -104, -105, -106, -106, -107, -108, + -109, -109, -110, -111, -111, -112, -112, -113, + -113, -114, -114, -114, -115, -115, -115, -115, + -116, -116, -116, -116, -116, -116, -116, -116, + -116, -115, -115, -115, -115, -114, -114, -114, + -113, -113, -112, -112, -111, -111, -110, -110, + -109, -108, -108, -107, -106, -105, -104, -103, + -102, -101, -100, -99, -98, -97, -96, -95, + -94, -93, -91, -90, -89, -88, -86, -85, + -84, -82, -81, -79, -78, -76, -75, -73, + -71, -70, -68, -67, -65, -63, -62, -60, + -58, -56, -55, -53, -51, -49, -47, -45, + -44, -42, -40, -38, -36, -34, -32, -30, + -28, -26, -24, -22, -20, -18, -16, -14, + -12, -10, -8, -6, -4, -2, 0, 1, + 3, 5, 7, 9, 11, 13, 15, 17, + 19, 21, 23, 25, 27, 29, 31, 33, + 35, 37, 39, 41, 43, 45, 46, 48, + 50, 52, 54, 55, 57, 59, 61, 62, + 64, 66, 67, 69, 71, 72, 74, 75, + 77, 78, 80, 81, 83, 84, 86, 87, + 88, 90, 91, 92, 93, 95, 96, 97, + 98, 99, 100, 101, 102, 103, 104, 105, + 106, 106, 107, 108, 109, 109, 110, 111, + 111, 112, 112, 113, 113, 114, 114, 114, + 115, 115, 115, 115, 116, 116, 116, 116, + 116, 116, 116, 116, 116, 115, 115, 115, + 115, 114, 114, 114, 113, 113, 112, 112, + 111, 111, 110, 110, 109, 108, 108, 107, + 106, 105, 104, 103, 102, 101, 100, 99, + 98, 97, 96, 95, 94, 93, 91, 90, + 89, 88, 86, 85, 84, 82, 81, 79, + 78, 76, 75, 73, 71, 70, 68, 67, + 65, 63, 62, 60, 58, 56, 55, 53, + 51, 49, 47, 45, 44, 42, 40, 38, + 36, 34, 32, 30, 28, 26, 24, 22, + 20, 18, 16, 14, 12, 10, 8, 6, + 4, 2, 0, -1, -3, -5, -7, -9, -11 +}; + +static u16 i2c_ident[] = { + V4L2_IDENT_OV9650, + V4L2_IDENT_OV9655, + V4L2_IDENT_SOI968, + V4L2_IDENT_OV7660, + V4L2_IDENT_OV7670, + V4L2_IDENT_MT9V011, + V4L2_IDENT_MT9V111, + V4L2_IDENT_MT9V112, + V4L2_IDENT_MT9M001C12ST, + V4L2_IDENT_MT9M111, + V4L2_IDENT_HV7131R, +}; + +static u16 bridge_init[][2] = { + {0x1000, 0x78}, {0x1001, 0x40}, {0x1002, 0x1c}, + {0x1020, 0x80}, {0x1061, 0x01}, {0x1067, 0x40}, + {0x1068, 0x30}, {0x1069, 0x20}, {0x106a, 0x10}, + {0x106b, 0x08}, {0x1188, 0x87}, {0x11a1, 0x00}, + {0x11a2, 0x00}, {0x11a3, 0x6a}, {0x11a4, 0x50}, + {0x11ab, 0x00}, {0x11ac, 0x00}, {0x11ad, 0x50}, + {0x11ae, 0x3c}, {0x118a, 0x04}, {0x0395, 0x04}, + {0x11b8, 0x3a}, {0x118b, 0x0e}, {0x10f7, 0x05}, + {0x10f8, 0x14}, {0x10fa, 0xff}, {0x10f9, 0x00}, + {0x11ba, 0x0a}, {0x11a5, 0x2d}, {0x11a6, 0x2d}, + {0x11a7, 0x3a}, {0x11a8, 0x05}, {0x11a9, 0x04}, + {0x11aa, 0x3f}, {0x11af, 0x28}, {0x11b0, 0xd8}, + {0x11b1, 0x14}, {0x11b2, 0xec}, {0x11b3, 0x32}, + {0x11b4, 0xdd}, {0x11b5, 0x32}, {0x11b6, 0xdd}, + {0x10e0, 0x2c}, {0x11bc, 0x40}, {0x11bd, 0x01}, + {0x11be, 0xf0}, {0x11bf, 0x00}, {0x118c, 0x1f}, + {0x118d, 0x1f}, {0x118e, 0x1f}, {0x118f, 0x1f}, + {0x1180, 0x01}, {0x1181, 0x00}, {0x1182, 0x01}, + {0x1183, 0x00}, {0x1184, 0x50}, {0x1185, 0x80} +}; + +/* Gain = (bit[3:0] / 16 + 1) * (bit[4] + 1) * (bit[5] + 1) * (bit[6] + 1) */ +static u8 ov_gain[] = { + 0x00 /* 1x */, 0x04 /* 1.25x */, 0x08 /* 1.5x */, 0x0c /* 1.75x */, + 0x10 /* 2x */, 0x12 /* 2.25x */, 0x14 /* 2.5x */, 0x16 /* 2.75x */, + 0x18 /* 3x */, 0x1a /* 3.25x */, 0x1c /* 3.5x */, 0x1e /* 3.75x */, + 0x30 /* 4x */, 0x31 /* 4.25x */, 0x32 /* 4.5x */, 0x33 /* 4.75x */, + 0x34 /* 5x */, 0x35 /* 5.25x */, 0x36 /* 5.5x */, 0x37 /* 5.75x */, + 0x38 /* 6x */, 0x39 /* 6.25x */, 0x3a /* 6.5x */, 0x3b /* 6.75x */, + 0x3c /* 7x */, 0x3d /* 7.25x */, 0x3e /* 7.5x */, 0x3f /* 7.75x */, + 0x70 /* 8x */ +}; + +/* Gain = (bit[8] + 1) * (bit[7] + 1) * (bit[6:0] * 0.03125) */ +static u16 micron1_gain[] = { + /* 1x 1.25x 1.5x 1.75x */ + 0x0020, 0x0028, 0x0030, 0x0038, + /* 2x 2.25x 2.5x 2.75x */ + 0x00a0, 0x00a4, 0x00a8, 0x00ac, + /* 3x 3.25x 3.5x 3.75x */ + 0x00b0, 0x00b4, 0x00b8, 0x00bc, + /* 4x 4.25x 4.5x 4.75x */ + 0x00c0, 0x00c4, 0x00c8, 0x00cc, + /* 5x 5.25x 5.5x 5.75x */ + 0x00d0, 0x00d4, 0x00d8, 0x00dc, + /* 6x 6.25x 6.5x 6.75x */ + 0x00e0, 0x00e4, 0x00e8, 0x00ec, + /* 7x 7.25x 7.5x 7.75x */ + 0x00f0, 0x00f4, 0x00f8, 0x00fc, + /* 8x */ + 0x01c0 +}; + +/* mt9m001 sensor uses a different gain formula then other micron sensors */ +/* Gain = (bit[6] + 1) * (bit[5-0] * 0.125) */ +static u16 micron2_gain[] = { + /* 1x 1.25x 1.5x 1.75x */ + 0x0008, 0x000a, 0x000c, 0x000e, + /* 2x 2.25x 2.5x 2.75x */ + 0x0010, 0x0012, 0x0014, 0x0016, + /* 3x 3.25x 3.5x 3.75x */ + 0x0018, 0x001a, 0x001c, 0x001e, + /* 4x 4.25x 4.5x 4.75x */ + 0x0020, 0x0051, 0x0052, 0x0053, + /* 5x 5.25x 5.5x 5.75x */ + 0x0054, 0x0055, 0x0056, 0x0057, + /* 6x 6.25x 6.5x 6.75x */ + 0x0058, 0x0059, 0x005a, 0x005b, + /* 7x 7.25x 7.5x 7.75x */ + 0x005c, 0x005d, 0x005e, 0x005f, + /* 8x */ + 0x0060 +}; + +/* Gain = .5 + bit[7:0] / 16 */ +static u8 hv7131r_gain[] = { + 0x08 /* 1x */, 0x0c /* 1.25x */, 0x10 /* 1.5x */, 0x14 /* 1.75x */, + 0x18 /* 2x */, 0x1c /* 2.25x */, 0x20 /* 2.5x */, 0x24 /* 2.75x */, + 0x28 /* 3x */, 0x2c /* 3.25x */, 0x30 /* 3.5x */, 0x34 /* 3.75x */, + 0x38 /* 4x */, 0x3c /* 4.25x */, 0x40 /* 4.5x */, 0x44 /* 4.75x */, + 0x48 /* 5x */, 0x4c /* 5.25x */, 0x50 /* 5.5x */, 0x54 /* 5.75x */, + 0x58 /* 6x */, 0x5c /* 6.25x */, 0x60 /* 6.5x */, 0x64 /* 6.75x */, + 0x68 /* 7x */, 0x6c /* 7.25x */, 0x70 /* 7.5x */, 0x74 /* 7.75x */, + 0x78 /* 8x */ +}; + +static u8 soi968_init[][2] = { + {0x12, 0x80}, {0x0c, 0x00}, {0x0f, 0x1f}, + {0x11, 0x80}, {0x38, 0x52}, {0x1e, 0x00}, + {0x33, 0x08}, {0x35, 0x8c}, {0x36, 0x0c}, + {0x37, 0x04}, {0x45, 0x04}, {0x47, 0xff}, + {0x3e, 0x00}, {0x3f, 0x00}, {0x3b, 0x20}, + {0x3a, 0x96}, {0x3d, 0x0a}, {0x14, 0x8e}, + {0x13, 0x8a}, {0x12, 0x40}, {0x17, 0x13}, + {0x18, 0x63}, {0x19, 0x01}, {0x1a, 0x79}, + {0x32, 0x24}, {0x03, 0x00}, {0x11, 0x40}, + {0x2a, 0x10}, {0x2b, 0xe0}, {0x10, 0x32}, + {0x00, 0x00}, {0x01, 0x80}, {0x02, 0x80}, +}; + +static u8 ov7660_init[][2] = { + {0x0e, 0x80}, {0x0d, 0x08}, {0x0f, 0xc3}, + {0x04, 0xc3}, {0x10, 0x40}, {0x11, 0x40}, + {0x12, 0x05}, {0x13, 0xba}, {0x14, 0x2a}, + {0x37, 0x0f}, {0x38, 0x02}, {0x39, 0x43}, + {0x3a, 0x00}, {0x69, 0x90}, {0x2d, 0xf6}, + {0x2e, 0x0b}, {0x01, 0x78}, {0x02, 0x50}, +}; + +static u8 ov7670_init[][2] = { + {0x12, 0x80}, {0x11, 0x80}, {0x3a, 0x04}, {0x12, 0x01}, + {0x32, 0xb6}, {0x03, 0x0a}, {0x0c, 0x00}, {0x3e, 0x00}, + {0x70, 0x3a}, {0x71, 0x35}, {0x72, 0x11}, {0x73, 0xf0}, + {0xa2, 0x02}, {0x13, 0xe0}, {0x00, 0x00}, {0x10, 0x00}, + {0x0d, 0x40}, {0x14, 0x28}, {0xa5, 0x05}, {0xab, 0x07}, + {0x24, 0x95}, {0x25, 0x33}, {0x26, 0xe3}, {0x9f, 0x75}, + {0xa0, 0x65}, {0xa1, 0x0b}, {0xa6, 0xd8}, {0xa7, 0xd8}, + {0xa8, 0xf0}, {0xa9, 0x90}, {0xaa, 0x94}, {0x13, 0xe5}, + {0x0e, 0x61}, {0x0f, 0x4b}, {0x16, 0x02}, {0x1e, 0x27}, + {0x21, 0x02}, {0x22, 0x91}, {0x29, 0x07}, {0x33, 0x0b}, + {0x35, 0x0b}, {0x37, 0x1d}, {0x38, 0x71}, {0x39, 0x2a}, + {0x3c, 0x78}, {0x4d, 0x40}, {0x4e, 0x20}, {0x69, 0x00}, + {0x74, 0x19}, {0x8d, 0x4f}, {0x8e, 0x00}, {0x8f, 0x00}, + {0x90, 0x00}, {0x91, 0x00}, {0x96, 0x00}, {0x9a, 0x80}, + {0xb0, 0x84}, {0xb1, 0x0c}, {0xb2, 0x0e}, {0xb3, 0x82}, + {0xb8, 0x0a}, {0x43, 0x0a}, {0x44, 0xf0}, {0x45, 0x20}, + {0x46, 0x7d}, {0x47, 0x29}, {0x48, 0x4a}, {0x59, 0x8c}, + {0x5a, 0xa5}, {0x5b, 0xde}, {0x5c, 0x96}, {0x5d, 0x66}, + {0x5e, 0x10}, {0x6c, 0x0a}, {0x6d, 0x55}, {0x6e, 0x11}, + {0x6f, 0x9e}, {0x6a, 0x40}, {0x01, 0x40}, {0x02, 0x40}, + {0x13, 0xe7}, {0x4f, 0x6e}, {0x50, 0x70}, {0x51, 0x02}, + {0x52, 0x1d}, {0x53, 0x56}, {0x54, 0x73}, {0x55, 0x0a}, + {0x56, 0x55}, {0x57, 0x80}, {0x58, 0x9e}, {0x41, 0x08}, + {0x3f, 0x02}, {0x75, 0x03}, {0x76, 0x63}, {0x4c, 0x04}, + {0x77, 0x06}, {0x3d, 0x02}, {0x4b, 0x09}, {0xc9, 0x30}, + {0x41, 0x08}, {0x56, 0x48}, {0x34, 0x11}, {0xa4, 0x88}, + {0x96, 0x00}, {0x97, 0x30}, {0x98, 0x20}, {0x99, 0x30}, + {0x9a, 0x84}, {0x9b, 0x29}, {0x9c, 0x03}, {0x9d, 0x99}, + {0x9e, 0x7f}, {0x78, 0x04}, {0x79, 0x01}, {0xc8, 0xf0}, + {0x79, 0x0f}, {0xc8, 0x00}, {0x79, 0x10}, {0xc8, 0x7e}, + {0x79, 0x0a}, {0xc8, 0x80}, {0x79, 0x0b}, {0xc8, 0x01}, + {0x79, 0x0c}, {0xc8, 0x0f}, {0x79, 0x0d}, {0xc8, 0x20}, + {0x79, 0x09}, {0xc8, 0x80}, {0x79, 0x02}, {0xc8, 0xc0}, + {0x79, 0x03}, {0xc8, 0x40}, {0x79, 0x05}, {0xc8, 0x30}, + {0x79, 0x26}, {0x62, 0x20}, {0x63, 0x00}, {0x64, 0x06}, + {0x65, 0x00}, {0x66, 0x05}, {0x94, 0x05}, {0x95, 0x0a}, + {0x17, 0x13}, {0x18, 0x01}, {0x19, 0x02}, {0x1a, 0x7a}, + {0x46, 0x59}, {0x47, 0x30}, {0x58, 0x9a}, {0x59, 0x84}, + {0x5a, 0x91}, {0x5b, 0x57}, {0x5c, 0x75}, {0x5d, 0x6d}, + {0x5e, 0x13}, {0x64, 0x07}, {0x94, 0x07}, {0x95, 0x0d}, + {0xa6, 0xdf}, {0xa7, 0xdf}, {0x48, 0x4d}, {0x51, 0x00}, + {0x6b, 0x0a}, {0x11, 0x80}, {0x2a, 0x00}, {0x2b, 0x00}, + {0x92, 0x00}, {0x93, 0x00}, {0x55, 0x0a}, {0x56, 0x60}, + {0x4f, 0x6e}, {0x50, 0x70}, {0x51, 0x00}, {0x52, 0x1d}, + {0x53, 0x56}, {0x54, 0x73}, {0x58, 0x9a}, {0x4f, 0x6e}, + {0x50, 0x70}, {0x51, 0x00}, {0x52, 0x1d}, {0x53, 0x56}, + {0x54, 0x73}, {0x58, 0x9a}, {0x3f, 0x01}, {0x7b, 0x03}, + {0x7c, 0x09}, {0x7d, 0x16}, {0x7e, 0x38}, {0x7f, 0x47}, + {0x80, 0x53}, {0x81, 0x5e}, {0x82, 0x6a}, {0x83, 0x74}, + {0x84, 0x80}, {0x85, 0x8c}, {0x86, 0x9b}, {0x87, 0xb2}, + {0x88, 0xcc}, {0x89, 0xe5}, {0x7a, 0x24}, {0x3b, 0x00}, + {0x9f, 0x76}, {0xa0, 0x65}, {0x13, 0xe2}, {0x6b, 0x0a}, + {0x11, 0x80}, {0x2a, 0x00}, {0x2b, 0x00}, {0x92, 0x00}, + {0x93, 0x00}, +}; + +static u8 ov9650_init[][2] = { + {0x12, 0x80}, {0x00, 0x00}, {0x01, 0x78}, + {0x02, 0x78}, {0x03, 0x36}, {0x04, 0x03}, + {0x05, 0x00}, {0x06, 0x00}, {0x08, 0x00}, + {0x09, 0x01}, {0x0c, 0x00}, {0x0d, 0x00}, + {0x0e, 0xa0}, {0x0f, 0x52}, {0x10, 0x7c}, + {0x11, 0x80}, {0x12, 0x45}, {0x13, 0xc2}, + {0x14, 0x2e}, {0x15, 0x00}, {0x16, 0x07}, + {0x17, 0x24}, {0x18, 0xc5}, {0x19, 0x00}, + {0x1a, 0x3c}, {0x1b, 0x00}, {0x1e, 0x04}, + {0x1f, 0x00}, {0x24, 0x78}, {0x25, 0x68}, + {0x26, 0xd4}, {0x27, 0x80}, {0x28, 0x80}, + {0x29, 0x30}, {0x2a, 0x00}, {0x2b, 0x00}, + {0x2c, 0x80}, {0x2d, 0x00}, {0x2e, 0x00}, + {0x2f, 0x00}, {0x30, 0x08}, {0x31, 0x30}, + {0x32, 0x84}, {0x33, 0xe2}, {0x34, 0xbf}, + {0x35, 0x81}, {0x36, 0xf9}, {0x37, 0x00}, + {0x38, 0x93}, {0x39, 0x50}, {0x3a, 0x01}, + {0x3b, 0x01}, {0x3c, 0x73}, {0x3d, 0x19}, + {0x3e, 0x0b}, {0x3f, 0x80}, {0x40, 0xc1}, + {0x41, 0x00}, {0x42, 0x08}, {0x67, 0x80}, + {0x68, 0x80}, {0x69, 0x40}, {0x6a, 0x00}, + {0x6b, 0x0a}, {0x8b, 0x06}, {0x8c, 0x20}, + {0x8d, 0x00}, {0x8e, 0x00}, {0x8f, 0xdf}, + {0x92, 0x00}, {0x93, 0x00}, {0x94, 0x88}, + {0x95, 0x88}, {0x96, 0x04}, {0xa1, 0x00}, + {0xa5, 0x80}, {0xa8, 0x80}, {0xa9, 0xb8}, + {0xaa, 0x92}, {0xab, 0x0a}, +}; + +static u8 ov9655_init[][2] = { + {0x12, 0x80}, {0x12, 0x01}, {0x0d, 0x00}, {0x0e, 0x61}, + {0x11, 0x80}, {0x13, 0xba}, {0x14, 0x2e}, {0x16, 0x24}, + {0x1e, 0x04}, {0x1e, 0x04}, {0x1e, 0x04}, {0x27, 0x08}, + {0x28, 0x08}, {0x29, 0x15}, {0x2c, 0x08}, {0x32, 0xbf}, + {0x34, 0x3d}, {0x35, 0x00}, {0x36, 0xf8}, {0x38, 0x12}, + {0x39, 0x57}, {0x3a, 0x00}, {0x3b, 0xcc}, {0x3c, 0x0c}, + {0x3d, 0x19}, {0x3e, 0x0c}, {0x3f, 0x01}, {0x41, 0x40}, + {0x42, 0x80}, {0x45, 0x46}, {0x46, 0x62}, {0x47, 0x2a}, + {0x48, 0x3c}, {0x4a, 0xf0}, {0x4b, 0xdc}, {0x4c, 0xdc}, + {0x4d, 0xdc}, {0x4e, 0xdc}, {0x69, 0x02}, {0x6c, 0x04}, + {0x6f, 0x9e}, {0x70, 0x05}, {0x71, 0x78}, {0x77, 0x02}, + {0x8a, 0x23}, {0x8c, 0x0d}, {0x90, 0x7e}, {0x91, 0x7c}, + {0x9f, 0x6e}, {0xa0, 0x6e}, {0xa5, 0x68}, {0xa6, 0x60}, + {0xa8, 0xc1}, {0xa9, 0xfa}, {0xaa, 0x92}, {0xab, 0x04}, + {0xac, 0x80}, {0xad, 0x80}, {0xae, 0x80}, {0xaf, 0x80}, + {0xb2, 0xf2}, {0xb3, 0x20}, {0xb5, 0x00}, {0xb6, 0xaf}, + {0xbb, 0xae}, {0xbc, 0x44}, {0xbd, 0x44}, {0xbe, 0x3b}, + {0xbf, 0x3a}, {0xc0, 0xe2}, {0xc1, 0xc8}, {0xc2, 0x01}, + {0xc4, 0x00}, {0xc6, 0x85}, {0xc7, 0x81}, {0xc9, 0xe0}, + {0xca, 0xe8}, {0xcc, 0xd8}, {0xcd, 0x93}, {0x12, 0x61}, + {0x36, 0xfa}, {0x8c, 0x8d}, {0xc0, 0xaa}, {0x69, 0x0a}, + {0x03, 0x12}, {0x17, 0x14}, {0x18, 0x00}, {0x19, 0x01}, + {0x1a, 0x3d}, {0x32, 0xbf}, {0x11, 0x80}, {0x2a, 0x10}, + {0x2b, 0x0a}, {0x92, 0x00}, {0x93, 0x00}, {0x1e, 0x04}, + {0x1e, 0x04}, {0x10, 0x7c}, {0x04, 0x03}, {0xa1, 0x00}, + {0x2d, 0x00}, {0x2e, 0x00}, {0x00, 0x00}, {0x01, 0x80}, + {0x02, 0x80}, {0x12, 0x61}, {0x36, 0xfa}, {0x8c, 0x8d}, + {0xc0, 0xaa}, {0x69, 0x0a}, {0x03, 0x12}, {0x17, 0x14}, + {0x18, 0x00}, {0x19, 0x01}, {0x1a, 0x3d}, {0x32, 0xbf}, + {0x11, 0x80}, {0x2a, 0x10}, {0x2b, 0x0a}, {0x92, 0x00}, + {0x93, 0x00}, {0x04, 0x01}, {0x10, 0x1f}, {0xa1, 0x00}, + {0x00, 0x0a}, {0xa1, 0x00}, {0x10, 0x5d}, {0x04, 0x03}, + {0x00, 0x01}, {0xa1, 0x00}, {0x10, 0x7c}, {0x04, 0x03}, + {0x00, 0x03}, {0x00, 0x0a}, {0x00, 0x10}, {0x00, 0x13}, +}; + +static u16 mt9v112_init[][2] = { + {0xf0, 0x0000}, {0x0d, 0x0021}, {0x0d, 0x0020}, + {0x34, 0xc019}, {0x0a, 0x0011}, {0x0b, 0x000b}, + {0x20, 0x0703}, {0x35, 0x2022}, {0xf0, 0x0001}, + {0x05, 0x0000}, {0x06, 0x340c}, {0x3b, 0x042a}, + {0x3c, 0x0400}, {0xf0, 0x0002}, {0x2e, 0x0c58}, + {0x5b, 0x0001}, {0xc8, 0x9f0b}, {0xf0, 0x0001}, + {0x9b, 0x5300}, {0xf0, 0x0000}, {0x2b, 0x0020}, + {0x2c, 0x002a}, {0x2d, 0x0032}, {0x2e, 0x0020}, + {0x09, 0x01dc}, {0x01, 0x000c}, {0x02, 0x0020}, + {0x03, 0x01e0}, {0x04, 0x0280}, {0x06, 0x000c}, + {0x05, 0x0098}, {0x20, 0x0703}, {0x09, 0x01f2}, + {0x2b, 0x00a0}, {0x2c, 0x00a0}, {0x2d, 0x00a0}, + {0x2e, 0x00a0}, {0x01, 0x000c}, {0x02, 0x0020}, + {0x03, 0x01e0}, {0x04, 0x0280}, {0x06, 0x000c}, + {0x05, 0x0098}, {0x09, 0x01c1}, {0x2b, 0x00ae}, + {0x2c, 0x00ae}, {0x2d, 0x00ae}, {0x2e, 0x00ae}, +}; + +static u16 mt9v111_init[][2] = { + {0x01, 0x0004}, {0x0d, 0x0001}, {0x0d, 0x0000}, + {0x01, 0x0001}, {0x02, 0x0016}, {0x03, 0x01e1}, + {0x04, 0x0281}, {0x05, 0x0004}, {0x07, 0x3002}, + {0x21, 0x0000}, {0x25, 0x4024}, {0x26, 0xff03}, + {0x27, 0xff10}, {0x2b, 0x7828}, {0x2c, 0xb43c}, + {0x2d, 0xf0a0}, {0x2e, 0x0c64}, {0x2f, 0x0064}, + {0x67, 0x4010}, {0x06, 0x301e}, {0x08, 0x0480}, + {0x01, 0x0004}, {0x02, 0x0016}, {0x03, 0x01e6}, + {0x04, 0x0286}, {0x05, 0x0004}, {0x06, 0x0000}, + {0x07, 0x3002}, {0x08, 0x0008}, {0x0c, 0x0000}, + {0x0d, 0x0000}, {0x0e, 0x0000}, {0x0f, 0x0000}, + {0x10, 0x0000}, {0x11, 0x0000}, {0x12, 0x00b0}, + {0x13, 0x007c}, {0x14, 0x0000}, {0x15, 0x0000}, + {0x16, 0x0000}, {0x17, 0x0000}, {0x18, 0x0000}, + {0x19, 0x0000}, {0x1a, 0x0000}, {0x1b, 0x0000}, + {0x1c, 0x0000}, {0x1d, 0x0000}, {0x30, 0x0000}, + {0x30, 0x0005}, {0x31, 0x0000}, {0x02, 0x0016}, + {0x03, 0x01e1}, {0x04, 0x0281}, {0x05, 0x0004}, + {0x06, 0x0000}, {0x07, 0x3002}, {0x06, 0x002d}, + {0x05, 0x0004}, {0x09, 0x0064}, {0x2b, 0x00a0}, + {0x2c, 0x00a0}, {0x2d, 0x00a0}, {0x2e, 0x00a0}, + {0x02, 0x0016}, {0x03, 0x01e1}, {0x04, 0x0281}, + {0x05, 0x0004}, {0x06, 0x002d}, {0x07, 0x3002}, + {0x0e, 0x0008}, {0x06, 0x002d}, {0x05, 0x0004}, +}; + +static u16 mt9v011_init[][2] = { + {0x07, 0x0002}, {0x0d, 0x0001}, {0x0d, 0x0000}, + {0x01, 0x0008}, {0x02, 0x0016}, {0x03, 0x01e1}, + {0x04, 0x0281}, {0x05, 0x0083}, {0x06, 0x0006}, + {0x0d, 0x0002}, {0x0a, 0x0000}, {0x0b, 0x0000}, + {0x0c, 0x0000}, {0x0d, 0x0000}, {0x0e, 0x0000}, + {0x0f, 0x0000}, {0x10, 0x0000}, {0x11, 0x0000}, + {0x12, 0x0000}, {0x13, 0x0000}, {0x14, 0x0000}, + {0x15, 0x0000}, {0x16, 0x0000}, {0x17, 0x0000}, + {0x18, 0x0000}, {0x19, 0x0000}, {0x1a, 0x0000}, + {0x1b, 0x0000}, {0x1c, 0x0000}, {0x1d, 0x0000}, + {0x32, 0x0000}, {0x20, 0x1101}, {0x21, 0x0000}, + {0x22, 0x0000}, {0x23, 0x0000}, {0x24, 0x0000}, + {0x25, 0x0000}, {0x26, 0x0000}, {0x27, 0x0024}, + {0x2f, 0xf7b0}, {0x30, 0x0005}, {0x31, 0x0000}, + {0x32, 0x0000}, {0x33, 0x0000}, {0x34, 0x0100}, + {0x3d, 0x068f}, {0x40, 0x01e0}, {0x41, 0x00d1}, + {0x44, 0x0082}, {0x5a, 0x0000}, {0x5b, 0x0000}, + {0x5c, 0x0000}, {0x5d, 0x0000}, {0x5e, 0x0000}, + {0x5f, 0xa31d}, {0x62, 0x0611}, {0x0a, 0x0000}, + {0x06, 0x0029}, {0x05, 0x0009}, {0x20, 0x1101}, + {0x20, 0x1101}, {0x09, 0x0064}, {0x07, 0x0003}, + {0x2b, 0x0033}, {0x2c, 0x00a0}, {0x2d, 0x00a0}, + {0x2e, 0x0033}, {0x07, 0x0002}, {0x06, 0x0000}, + {0x06, 0x0029}, {0x05, 0x0009}, +}; + +static u16 mt9m001_init[][2] = { + {0x0d, 0x0001}, {0x0d, 0x0000}, {0x01, 0x000e}, + {0x02, 0x0014}, {0x03, 0x03c1}, {0x04, 0x0501}, + {0x05, 0x0083}, {0x06, 0x0006}, {0x0d, 0x0002}, + {0x0a, 0x0000}, {0x0c, 0x0000}, {0x11, 0x0000}, + {0x1e, 0x8000}, {0x5f, 0x8904}, {0x60, 0x0000}, + {0x61, 0x0000}, {0x62, 0x0498}, {0x63, 0x0000}, + {0x64, 0x0000}, {0x20, 0x111d}, {0x06, 0x00f2}, + {0x05, 0x0013}, {0x09, 0x10f2}, {0x07, 0x0003}, + {0x2b, 0x002a}, {0x2d, 0x002a}, {0x2c, 0x002a}, + {0x2e, 0x0029}, {0x07, 0x0002}, +}; + +static u16 mt9m111_init[][2] = { + {0xf0, 0x0000}, {0x0d, 0x0008}, {0x0d, 0x0009}, + {0x0d, 0x0008}, {0xf0, 0x0001}, {0x3a, 0x4300}, + {0x9b, 0x4300}, {0xa1, 0x0280}, {0xa4, 0x0200}, + {0x06, 0x308e}, {0xf0, 0x0000}, +}; + +static u8 hv7131r_init[][2] = { + {0x02, 0x08}, {0x02, 0x00}, {0x01, 0x08}, + {0x02, 0x00}, {0x20, 0x00}, {0x21, 0xd0}, + {0x22, 0x00}, {0x23, 0x09}, {0x01, 0x08}, + {0x01, 0x08}, {0x01, 0x08}, {0x25, 0x07}, + {0x26, 0xc3}, {0x27, 0x50}, {0x30, 0x62}, + {0x31, 0x10}, {0x32, 0x06}, {0x33, 0x10}, + {0x20, 0x00}, {0x21, 0xd0}, {0x22, 0x00}, + {0x23, 0x09}, {0x01, 0x08}, +}; + +int reg_r(struct gspca_dev *gspca_dev, u16 reg, u16 length) +{ + struct usb_device *dev = gspca_dev->dev; + int result; + result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), + 0x00, + USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, + reg, + 0x00, + gspca_dev->usb_buf, + length, + 500); + if (unlikely(result < 0 || result != length)) { + err("Read register failed 0x%02X", reg); + return -EIO; + } + return 0; +} + +int reg_w(struct gspca_dev *gspca_dev, u16 reg, const u8 *buffer, int length) +{ + struct usb_device *dev = gspca_dev->dev; + int result; + memcpy(gspca_dev->usb_buf, buffer, length); + result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), + 0x08, + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, + reg, + 0x00, + gspca_dev->usb_buf, + length, + 500); + if (unlikely(result < 0 || result != length)) { + err("Write register failed index 0x%02X", reg); + return -EIO; + } + return 0; +} + +int reg_w1(struct gspca_dev *gspca_dev, u16 reg, const u8 value) +{ + u8 data[1] = {value}; + return reg_w(gspca_dev, reg, data, 1); +} + +int i2c_w(struct gspca_dev *gspca_dev, const u8 *buffer) +{ + int i; + reg_w(gspca_dev, 0x10c0, buffer, 8); + for (i = 0; i < 5; i++) { + reg_r(gspca_dev, 0x10c0, 1); + if (gspca_dev->usb_buf[0] & 0x04) { + if (gspca_dev->usb_buf[0] & 0x08) + return -1; + return 0; + } + msleep(1); + } + return -1; +} + +int i2c_w1(struct gspca_dev *gspca_dev, u8 reg, u8 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + u8 row[8]; + + /* + * from the point of view of the bridge, the length + * includes the address + */ + row[0] = 0x81 | (2 << 4); + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = val; + row[4] = 0x00; + row[5] = 0x00; + row[6] = 0x00; + row[7] = 0x10; + + return i2c_w(gspca_dev, row); +} + +int i2c_w2(struct gspca_dev *gspca_dev, u8 reg, u16 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + /* + * from the point of view of the bridge, the length + * includes the address + */ + row[0] = 0x81 | (3 << 4); + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = (val >> 8) & 0xff; + row[4] = val & 0xff; + row[5] = 0x00; + row[6] = 0x00; + row[7] = 0x10; + + return i2c_w(gspca_dev, row); +} + +int i2c_r1(struct gspca_dev *gspca_dev, u8 reg, u8 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + row[0] = 0x81 | 0x10; + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = 0; + row[4] = 0; + row[5] = 0; + row[6] = 0; + row[7] = 0x10; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + row[0] = 0x81 | (2 << 4) | 0x02; + row[2] = 0; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + reg_r(gspca_dev, 0x10c2, 5); + *val = gspca_dev->usb_buf[3]; + return 0; +} + +int i2c_r2(struct gspca_dev *gspca_dev, u8 reg, u16 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 row[8]; + + row[0] = 0x81 | 0x10; + row[1] = sd->i2c_addr; + row[2] = reg; + row[3] = 0; + row[4] = 0; + row[5] = 0; + row[6] = 0; + row[7] = 0x10; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + row[0] = 0x81 | (3 << 4) | 0x02; + row[2] = 0; + reg_w(gspca_dev, 0x10c0, row, 8); + msleep(1); + reg_r(gspca_dev, 0x10c2, 5); + *val = (gspca_dev->usb_buf[2] << 8) | gspca_dev->usb_buf[3]; + return 0; +} + +static int ov9650_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov9650_init); i++) { + if (i2c_w1(gspca_dev, ov9650_init[i][0], + ov9650_init[i][1]) < 0) { + err("OV9650 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 1; + sd->vstart = 7; + return 0; +} + +static int ov9655_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov9655_init); i++) { + if (i2c_w1(gspca_dev, ov9655_init[i][0], + ov9655_init[i][1]) < 0) { + err("OV9655 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 0; + sd->vstart = 7; + return 0; +} + +static int soi968_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(soi968_init); i++) { + if (i2c_w1(gspca_dev, soi968_init[i][0], + soi968_init[i][1]) < 0) { + err("SOI968 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 60; + sd->vstart = 11; + return 0; +} + +static int ov7660_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov7660_init); i++) { + if (i2c_w1(gspca_dev, ov7660_init[i][0], + ov7660_init[i][1]) < 0) { + err("OV7660 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 1; + sd->vstart = 1; + return 0; +} + +static int ov7670_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(ov7670_init); i++) { + if (i2c_w1(gspca_dev, ov7670_init[i][0], + ov7670_init[i][1]) < 0) { + err("OV7670 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 0; + sd->vstart = 1; + return 0; +} + +static int mt9v_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + u16 value; + int ret; + + sd->i2c_addr = 0x5d; + ret = i2c_r2(gspca_dev, 0xff, &value); + if ((ret == 0) && (value == 0x8243)) { + for (i = 0; i < ARRAY_SIZE(mt9v011_init); i++) { + if (i2c_w2(gspca_dev, mt9v011_init[i][0], + mt9v011_init[i][1]) < 0) { + err("MT9V011 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 2; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V011; + info("MT9V011 sensor detected"); + return 0; + } + + sd->i2c_addr = 0x5c; + i2c_w2(gspca_dev, 0x01, 0x0004); + ret = i2c_r2(gspca_dev, 0xff, &value); + if ((ret == 0) && (value == 0x823a)) { + for (i = 0; i < ARRAY_SIZE(mt9v111_init); i++) { + if (i2c_w2(gspca_dev, mt9v111_init[i][0], + mt9v111_init[i][1]) < 0) { + err("MT9V111 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 2; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V111; + info("MT9V111 sensor detected"); + return 0; + } + + sd->i2c_addr = 0x5d; + ret = i2c_w2(gspca_dev, 0xf0, 0x0000); + if (ret < 0) { + sd->i2c_addr = 0x48; + i2c_w2(gspca_dev, 0xf0, 0x0000); + } + ret = i2c_r2(gspca_dev, 0x00, &value); + if ((ret == 0) && (value == 0x1229)) { + for (i = 0; i < ARRAY_SIZE(mt9v112_init); i++) { + if (i2c_w2(gspca_dev, mt9v112_init[i][0], + mt9v112_init[i][1]) < 0) { + err("MT9V112 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 6; + sd->vstart = 2; + sd->sensor = SENSOR_MT9V112; + info("MT9V112 sensor detected"); + return 0; + } + + return -ENODEV; +} + +static int mt9m111_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + for (i = 0; i < ARRAY_SIZE(mt9m111_init); i++) { + if (i2c_w2(gspca_dev, mt9m111_init[i][0], + mt9m111_init[i][1]) < 0) { + err("MT9M111 sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 0; + sd->vstart = 2; + return 0; +} + +static int mt9m001_init_sensor(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + for (i = 0; i < ARRAY_SIZE(mt9m001_init); i++) { + if (i2c_w2(gspca_dev, mt9m001_init[i][0], + mt9m001_init[i][1]) < 0) { + err("MT9M001 sensor initialization failed"); + return -ENODEV; + } + } + /* disable hflip and vflip */ + gspca_dev->ctrl_dis = (1 << HFLIP_IDX) | (1 << VFLIP_IDX); + sd->hstart = 2; + sd->vstart = 2; + return 0; +} + +static int hv7131r_init_sensor(struct gspca_dev *gspca_dev) +{ + int i; + struct sd *sd = (struct sd *) gspca_dev; + + for (i = 0; i < ARRAY_SIZE(hv7131r_init); i++) { + if (i2c_w1(gspca_dev, hv7131r_init[i][0], + hv7131r_init[i][1]) < 0) { + err("HV7131R Sensor initialization failed"); + return -ENODEV; + } + } + sd->hstart = 0; + sd->vstart = 1; + return 0; +} + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV +static int input_kthread(void *data) +{ + struct gspca_dev *gspca_dev = (struct gspca_dev *)data; + struct sd *sd = (struct sd *) gspca_dev; + + DECLARE_WAIT_QUEUE_HEAD(wait); + set_freezable(); + for (;;) { + if (kthread_should_stop()) + break; + + if (reg_r(gspca_dev, 0x1005, 1) < 0) + continue; + + input_report_key(sd->input_dev, + KEY_CAMERA, + gspca_dev->usb_buf[0] & sd->input_gpio); + input_sync(sd->input_dev); + + wait_event_freezable_timeout(wait, + kthread_should_stop(), + msecs_to_jiffies(100)); + } + return 0; +} + + +static int sn9c20x_input_init(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + if (sd->input_gpio == 0) + return 0; + + sd->input_dev = input_allocate_device(); + if (!sd->input_dev) + return -ENOMEM; + + sd->input_dev->name = "SN9C20X Webcam"; + + sd->input_dev->phys = kasprintf(GFP_KERNEL, "usb-%s-%s", + gspca_dev->dev->bus->bus_name, + gspca_dev->dev->devpath); + + if (!sd->input_dev->phys) + return -ENOMEM; + + usb_to_input_id(gspca_dev->dev, &sd->input_dev->id); + sd->input_dev->dev.parent = &gspca_dev->dev->dev; + + set_bit(EV_KEY, sd->input_dev->evbit); + set_bit(KEY_CAMERA, sd->input_dev->keybit); + + if (input_register_device(sd->input_dev)) + return -EINVAL; + + sd->input_task = kthread_run(input_kthread, gspca_dev, "sn9c20x/%d", + gspca_dev->vdev.minor); + + if (IS_ERR(sd->input_task)) + return -EINVAL; + + return 0; +} + +static void sn9c20x_input_cleanup(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + if (sd->input_task != NULL && !IS_ERR(sd->input_task)) + kthread_stop(sd->input_task); + + if (sd->input_dev != NULL) { + input_unregister_device(sd->input_dev); + kfree(sd->input_dev->phys); + input_free_device(sd->input_dev); + sd->input_dev = NULL; + } +} +#endif + +static int set_cmatrix(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + s32 hue_coord, hue_index = 180 + sd->hue; + u8 cmatrix[21]; + memset(cmatrix, 0, 21); + + cmatrix[2] = (sd->contrast * 0x25 / 0x100) + 0x26; + cmatrix[0] = 0x13 + (cmatrix[2] - 0x26) * 0x13 / 0x25; + cmatrix[4] = 0x07 + (cmatrix[2] - 0x26) * 0x07 / 0x25; + cmatrix[18] = sd->brightness - 0x80; + + hue_coord = (hsv_red_x[hue_index] * sd->saturation) >> 8; + cmatrix[6] = (unsigned char)(hue_coord & 0xff); + cmatrix[7] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_red_y[hue_index] * sd->saturation) >> 8; + cmatrix[8] = (unsigned char)(hue_coord & 0xff); + cmatrix[9] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_green_x[hue_index] * sd->saturation) >> 8; + cmatrix[10] = (unsigned char)(hue_coord & 0xff); + cmatrix[11] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_green_y[hue_index] * sd->saturation) >> 8; + cmatrix[12] = (unsigned char)(hue_coord & 0xff); + cmatrix[13] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_blue_x[hue_index] * sd->saturation) >> 8; + cmatrix[14] = (unsigned char)(hue_coord & 0xff); + cmatrix[15] = (unsigned char)((hue_coord >> 8) & 0x0f); + + hue_coord = (hsv_blue_y[hue_index] * sd->saturation) >> 8; + cmatrix[16] = (unsigned char)(hue_coord & 0xff); + cmatrix[17] = (unsigned char)((hue_coord >> 8) & 0x0f); + + return reg_w(gspca_dev, 0x10e1, cmatrix, 21); +} + +static int set_gamma(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 gamma[17]; + u8 gval = sd->gamma * 0xb8 / 0x100; + + + gamma[0] = 0x0a; + gamma[1] = 0x13 + (gval * (0xcb - 0x13) / 0xb8); + gamma[2] = 0x25 + (gval * (0xee - 0x25) / 0xb8); + gamma[3] = 0x37 + (gval * (0xfa - 0x37) / 0xb8); + gamma[4] = 0x45 + (gval * (0xfc - 0x45) / 0xb8); + gamma[5] = 0x55 + (gval * (0xfb - 0x55) / 0xb8); + gamma[6] = 0x65 + (gval * (0xfc - 0x65) / 0xb8); + gamma[7] = 0x74 + (gval * (0xfd - 0x74) / 0xb8); + gamma[8] = 0x83 + (gval * (0xfe - 0x83) / 0xb8); + gamma[9] = 0x92 + (gval * (0xfc - 0x92) / 0xb8); + gamma[10] = 0xa1 + (gval * (0xfc - 0xa1) / 0xb8); + gamma[11] = 0xb0 + (gval * (0xfc - 0xb0) / 0xb8); + gamma[12] = 0xbf + (gval * (0xfb - 0xbf) / 0xb8); + gamma[13] = 0xce + (gval * (0xfb - 0xce) / 0xb8); + gamma[14] = 0xdf + (gval * (0xfd - 0xdf) / 0xb8); + gamma[15] = 0xea + (gval * (0xf9 - 0xea) / 0xb8); + gamma[16] = 0xf5; + + return reg_w(gspca_dev, 0x1190, gamma, 17); +} + +static int set_redblue(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + reg_w1(gspca_dev, 0x118c, sd->red); + reg_w1(gspca_dev, 0x118f, sd->blue); + return 0; +} + +static int set_hvflip(struct gspca_dev *gspca_dev) +{ + u8 value, tslb; + u16 value2; + struct sd *sd = (struct sd *) gspca_dev; + switch (sd->sensor) { + case SENSOR_OV9650: + i2c_r1(gspca_dev, 0x1e, &value); + value &= ~0x30; + tslb = 0x01; + if (sd->hflip) + value |= 0x20; + if (sd->vflip) { + value |= 0x10; + tslb = 0x49; + } + i2c_w1(gspca_dev, 0x1e, value); + i2c_w1(gspca_dev, 0x3a, tslb); + break; + case SENSOR_MT9V111: + case SENSOR_MT9V011: + i2c_r2(gspca_dev, 0x20, &value2); + value2 &= ~0xc0a0; + if (sd->hflip) + value2 |= 0x8080; + if (sd->vflip) + value2 |= 0x4020; + i2c_w2(gspca_dev, 0x20, value2); + break; + case SENSOR_MT9M111: + case SENSOR_MT9V112: + i2c_r2(gspca_dev, 0x20, &value2); + value2 &= ~0x0003; + if (sd->hflip) + value2 |= 0x0002; + if (sd->vflip) + value2 |= 0x0001; + i2c_w2(gspca_dev, 0x20, value2); + break; + case SENSOR_HV7131R: + i2c_r1(gspca_dev, 0x01, &value); + value &= ~0x03; + if (sd->vflip) + value |= 0x01; + if (sd->hflip) + value |= 0x02; + i2c_w1(gspca_dev, 0x01, value); + break; + } + return 0; +} + +static int set_exposure(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 exp[8] = {0x81, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1e}; + switch (sd->sensor) { + case SENSOR_OV7660: + case SENSOR_OV7670: + case SENSOR_SOI968: + case SENSOR_OV9655: + case SENSOR_OV9650: + exp[0] |= (3 << 4); + exp[2] = 0x2d; + exp[3] = sd->exposure & 0xff; + exp[4] = sd->exposure >> 8; + break; + case SENSOR_MT9M001: + case SENSOR_MT9M111: + case SENSOR_MT9V112: + case SENSOR_MT9V111: + case SENSOR_MT9V011: + exp[0] |= (3 << 4); + exp[2] = 0x09; + exp[3] = sd->exposure >> 8; + exp[4] = sd->exposure & 0xff; + break; + case SENSOR_HV7131R: + exp[0] |= (4 << 4); + exp[2] = 0x25; + exp[3] = ((sd->exposure * 0xffffff) / 0xffff) >> 16; + exp[4] = ((sd->exposure * 0xffffff) / 0xffff) >> 8; + exp[5] = ((sd->exposure * 0xffffff) / 0xffff) & 0xff; + break; + } + i2c_w(gspca_dev, exp); + return 0; +} + +static int set_gain(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 gain[8] = {0x81, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1d}; + switch (sd->sensor) { + case SENSOR_OV7660: + case SENSOR_OV7670: + case SENSOR_SOI968: + case SENSOR_OV9655: + case SENSOR_OV9650: + gain[0] |= (2 << 4); + gain[3] = ov_gain[sd->gain]; + break; + case SENSOR_MT9V011: + case SENSOR_MT9V111: + gain[0] |= (3 << 4); + gain[2] = 0x35; + gain[3] = micron1_gain[sd->gain] >> 8; + gain[4] = micron1_gain[sd->gain] & 0xff; + break; + case SENSOR_MT9V112: + case SENSOR_MT9M111: + gain[0] |= (3 << 4); + gain[2] = 0x2f; + gain[3] = micron1_gain[sd->gain] >> 8; + gain[4] = micron1_gain[sd->gain] & 0xff; + break; + case SENSOR_MT9M001: + gain[0] |= (3 << 4); + gain[2] = 0x2f; + gain[3] = micron2_gain[sd->gain] >> 8; + gain[4] = micron2_gain[sd->gain] & 0xff; + break; + case SENSOR_HV7131R: + gain[0] |= (2 << 4); + gain[2] = 0x30; + gain[3] = hv7131r_gain[sd->gain]; + break; + } + i2c_w(gspca_dev, gain); + return 0; +} + +static int sd_setbrightness(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->brightness = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getbrightness(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->brightness; + return 0; +} + + +static int sd_setcontrast(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->contrast = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getcontrast(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->contrast; + return 0; +} + +static int sd_setsaturation(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->saturation = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_getsaturation(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->saturation; + return 0; +} + +static int sd_sethue(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->hue = val; + if (gspca_dev->streaming) + return set_cmatrix(gspca_dev); + return 0; +} + +static int sd_gethue(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->hue; + return 0; +} + +static int sd_setgamma(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->gamma = val; + if (gspca_dev->streaming) + return set_gamma(gspca_dev); + return 0; +} + +static int sd_getgamma(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->gamma; + return 0; +} + +static int sd_setredbalance(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->red = val; + if (gspca_dev->streaming) + return set_redblue(gspca_dev); + return 0; +} + +static int sd_getredbalance(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->red; + return 0; +} + +static int sd_setbluebalance(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->blue = val; + if (gspca_dev->streaming) + return set_redblue(gspca_dev); + return 0; +} + +static int sd_getbluebalance(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->blue; + return 0; +} + +static int sd_sethflip(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->hflip = val; + if (gspca_dev->streaming) + return set_hvflip(gspca_dev); + return 0; +} + +static int sd_gethflip(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->hflip; + return 0; +} + +static int sd_setvflip(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->vflip = val; + if (gspca_dev->streaming) + return set_hvflip(gspca_dev); + return 0; +} + +static int sd_getvflip(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->vflip; + return 0; +} + +static int sd_setexposure(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->exposure = val; + if (gspca_dev->streaming) + return set_exposure(gspca_dev); + return 0; +} + +static int sd_getexposure(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->exposure; + return 0; +} + +static int sd_setgain(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->gain = val; + if (gspca_dev->streaming) + return set_gain(gspca_dev); + return 0; +} + +static int sd_getgain(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->gain; + return 0; +} + +static int sd_setautoexposure(struct gspca_dev *gspca_dev, s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + sd->auto_exposure = val; + return 0; +} + +static int sd_getautoexposure(struct gspca_dev *gspca_dev, s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + *val = sd->auto_exposure; + return 0; +} + +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int sd_dbg_g_register(struct gspca_dev *gspca_dev, + struct v4l2_dbg_register *reg) +{ + struct sd *sd = (struct sd *) gspca_dev; + switch (reg->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (reg->match.addr != 0) + return -EINVAL; + if (reg->reg < 0x1000 || reg->reg > 0x11ff) + return -EINVAL; + if (reg_r(gspca_dev, reg->reg, 1) < 0) + return -EINVAL; + reg->val = gspca_dev->usb_buf[0]; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (reg->match.addr != sd->i2c_addr) + return -EINVAL; + if (sd->sensor >= SENSOR_MT9V011 && + sd->sensor <= SENSOR_MT9M111) { + if (i2c_r2(gspca_dev, reg->reg, (u16 *)®->val) < 0) + return -EINVAL; + } else { + if (i2c_r1(gspca_dev, reg->reg, (u8 *)®->val) < 0) + return -EINVAL; + } + return 0; + } + return -EINVAL; +} + +static int sd_dbg_s_register(struct gspca_dev *gspca_dev, + struct v4l2_dbg_register *reg) +{ + struct sd *sd = (struct sd *) gspca_dev; + switch (reg->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (reg->match.addr != 0) + return -EINVAL; + if (reg->reg < 0x1000 || reg->reg > 0x11ff) + return -EINVAL; + if (reg_w1(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (reg->match.addr != sd->i2c_addr) + return -EINVAL; + if (sd->sensor >= SENSOR_MT9V011 && + sd->sensor <= SENSOR_MT9M111) { + if (i2c_w2(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + } else { + if (i2c_w1(gspca_dev, reg->reg, reg->val) < 0) + return -EINVAL; + } + return 0; + } + return -EINVAL; +} +#endif + +static int sd_chip_ident(struct gspca_dev *gspca_dev, + struct v4l2_dbg_chip_ident *chip) +{ + struct sd *sd = (struct sd *) gspca_dev; + + switch (chip->match.type) { + case V4L2_CHIP_MATCH_HOST: + if (chip->match.addr != 0) + return -EINVAL; + chip->revision = 0; + chip->ident = V4L2_IDENT_SN9C20X; + return 0; + case V4L2_CHIP_MATCH_I2C_ADDR: + if (chip->match.addr != sd->i2c_addr) + return -EINVAL; + chip->revision = 0; + chip->ident = i2c_ident[sd->sensor]; + return 0; + } + return -EINVAL; +} + +static int sd_config(struct gspca_dev *gspca_dev, + const struct usb_device_id *id) +{ + struct sd *sd = (struct sd *) gspca_dev; + struct cam *cam; + + cam = &gspca_dev->cam; + + sd->sensor = (id->driver_info >> 8) & 0xff; + sd->i2c_addr = id->driver_info & 0xff; + + switch (sd->sensor) { + case SENSOR_OV9650: + cam->cam_mode = sxga_mode; + cam->nmodes = ARRAY_SIZE(sxga_mode); + break; + default: + cam->cam_mode = vga_mode; + cam->nmodes = ARRAY_SIZE(vga_mode); + } + + sd->old_step = 0; + sd->older_step = 0; + sd->exposure_step = 16; + + sd->brightness = BRIGHTNESS_DEFAULT; + sd->contrast = CONTRAST_DEFAULT; + sd->saturation = SATURATION_DEFAULT; + sd->hue = HUE_DEFAULT; + sd->gamma = GAMMA_DEFAULT; + sd->red = RED_DEFAULT; + sd->blue = BLUE_DEFAULT; + + sd->hflip = HFLIP_DEFAULT; + sd->vflip = VFLIP_DEFAULT; + sd->exposure = EXPOSURE_DEFAULT; + sd->gain = GAIN_DEFAULT; + sd->auto_exposure = AUTO_EXPOSURE_DEFAULT; + + sd->quality = 95; + +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + sd->input_gpio = (id->driver_info >> 16) & 0xff; + if (sn9c20x_input_init(gspca_dev) < 0) + return -ENODEV; +#endif + return 0; +} + +static int sd_init(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int i; + u8 value; + u8 i2c_init[9] = + {0x80, sd->i2c_addr, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03}; + + for (i = 0; i < ARRAY_SIZE(bridge_init); i++) { + value = bridge_init[i][1]; + if (reg_w(gspca_dev, bridge_init[i][0], &value, 1) < 0) { + err("Device initialization failed"); + return -ENODEV; + } + } + + if (reg_w(gspca_dev, 0x10c0, i2c_init, 9) < 0) { + err("Device initialization failed"); + return -ENODEV; + } + + switch (sd->sensor) { + case SENSOR_OV9650: + if (ov9650_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV9650 sensor detected"); + break; + case SENSOR_OV9655: + if (ov9655_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV9655 sensor detected"); + break; + case SENSOR_SOI968: + if (soi968_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("SOI968 sensor detected"); + break; + case SENSOR_OV7660: + if (ov7660_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV7660 sensor detected"); + break; + case SENSOR_OV7670: + if (ov7670_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("OV7670 sensor detected"); + break; + case SENSOR_MT9VPRB: + if (mt9v_init_sensor(gspca_dev) < 0) + return -ENODEV; + break; + case SENSOR_MT9M111: + if (mt9m111_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("MT9M111 sensor detected"); + break; + case SENSOR_MT9M001: + if (mt9m001_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("MT9M001 sensor detected"); + break; + case SENSOR_HV7131R: + if (hv7131r_init_sensor(gspca_dev) < 0) + return -ENODEV; + info("HV7131R sensor detected"); + break; + default: + info("Unsupported Sensor"); + return -ENODEV; + } + + return 0; +} + +static void configure_sensor_output(struct gspca_dev *gspca_dev, int mode) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 value; + switch (sd->sensor) { + case SENSOR_OV9650: + if (mode & MODE_SXGA) { + i2c_w1(gspca_dev, 0x17, 0x1b); + i2c_w1(gspca_dev, 0x18, 0xbc); + i2c_w1(gspca_dev, 0x19, 0x01); + i2c_w1(gspca_dev, 0x1a, 0x82); + i2c_r1(gspca_dev, 0x12, &value); + i2c_w1(gspca_dev, 0x12, value & 0x07); + } else { + i2c_w1(gspca_dev, 0x17, 0x24); + i2c_w1(gspca_dev, 0x18, 0xc5); + i2c_w1(gspca_dev, 0x19, 0x00); + i2c_w1(gspca_dev, 0x1a, 0x3c); + i2c_r1(gspca_dev, 0x12, &value); + i2c_w1(gspca_dev, 0x12, (value & 0x7) | 0x40); + } + break; + } +} + +#define HW_WIN(mode, hstart, vstart) \ +((const u8 []){hstart & 0xff, hstart >> 8, \ +vstart & 0xff, vstart >> 8, \ +(mode & MODE_SXGA ? 1280 >> 4 : 640 >> 4), \ +(mode & MODE_SXGA ? 1024 >> 3 : 480 >> 3)}) + +#define CLR_WIN(width, height) \ +((const u8 [])\ +{0, width >> 2, 0, height >> 1,\ +((width >> 10) & 0x01) | ((height >> 8) & 0x6)}) + +static int sd_start(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int mode = gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv; + int width = gspca_dev->width; + int height = gspca_dev->height; + u8 fmt, scale = 0; + + sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (sd->jpeg_hdr == NULL) + return -ENOMEM; + + jpeg_define(sd->jpeg_hdr, height, width, + 0x21); + jpeg_set_qual(sd->jpeg_hdr, sd->quality); + + if (mode & MODE_RAW) + fmt = 0x2d; + else if (mode & MODE_JPEG) + fmt = 0x2c; + else + fmt = 0x2f; + + switch (mode & 0x0f) { + case 3: + scale = 0xc0; + info("Set 1280x1024"); + break; + case 2: + scale = 0x80; + info("Set 640x480"); + break; + case 1: + scale = 0x90; + info("Set 320x240"); + break; + case 0: + scale = 0xa0; + info("Set 160x120"); + break; + } + + configure_sensor_output(gspca_dev, mode); + reg_w(gspca_dev, 0x1100, sd->jpeg_hdr + JPEG_QT0_OFFSET, 64); + reg_w(gspca_dev, 0x1140, sd->jpeg_hdr + JPEG_QT1_OFFSET, 64); + reg_w(gspca_dev, 0x10fb, CLR_WIN(width, height), 5); + reg_w(gspca_dev, 0x1180, HW_WIN(mode, sd->hstart, sd->vstart), 6); + reg_w1(gspca_dev, 0x1189, scale); + reg_w1(gspca_dev, 0x10e0, fmt); + + set_cmatrix(gspca_dev); + set_gamma(gspca_dev); + set_redblue(gspca_dev); + set_gain(gspca_dev); + set_exposure(gspca_dev); + set_hvflip(gspca_dev); + + reg_r(gspca_dev, 0x1061, 1); + reg_w1(gspca_dev, 0x1061, gspca_dev->usb_buf[0] | 0x02); + return 0; +} + +static void sd_stopN(struct gspca_dev *gspca_dev) +{ + reg_r(gspca_dev, 0x1061, 1); + reg_w1(gspca_dev, 0x1061, gspca_dev->usb_buf[0] & ~0x02); +} + +static void sd_stop0(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + kfree(sd->jpeg_hdr); +} + +static void do_autoexposure(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int avg_lum, new_exp; + + if (!sd->auto_exposure) + return; + + avg_lum = atomic_read(&sd->avg_lum); + + /* + * some hardcoded values are present + * like those for maximal/minimal exposure + * and exposure steps + */ + if (avg_lum < MIN_AVG_LUM) { + if (sd->exposure > 0x1770) + return; + + new_exp = sd->exposure + sd->exposure_step; + if (new_exp > 0x1770) + new_exp = 0x1770; + if (new_exp < 0x10) + new_exp = 0x10; + sd->exposure = new_exp; + set_exposure(gspca_dev); + + sd->older_step = sd->old_step; + sd->old_step = 1; + + if (sd->old_step ^ sd->older_step) + sd->exposure_step /= 2; + else + sd->exposure_step += 2; + } + if (avg_lum > MAX_AVG_LUM) { + if (sd->exposure < 0x10) + return; + new_exp = sd->exposure - sd->exposure_step; + if (new_exp > 0x1700) + new_exp = 0x1770; + if (new_exp < 0x10) + new_exp = 0x10; + sd->exposure = new_exp; + set_exposure(gspca_dev); + sd->older_step = sd->old_step; + sd->old_step = 0; + + if (sd->old_step ^ sd->older_step) + sd->exposure_step /= 2; + else + sd->exposure_step += 2; + } +} + +static void sd_pkt_scan(struct gspca_dev *gspca_dev, + struct gspca_frame *frame, /* target */ + u8 *data, /* isoc packet */ + int len) /* iso packet length */ +{ + struct sd *sd = (struct sd *) gspca_dev; + int avg_lum; + static unsigned char frame_header[] = + {0xff, 0xff, 0x00, 0xc4, 0xc4, 0x96}; + if (len == 64 && memcmp(data, frame_header, 6) == 0) { + avg_lum = ((data[35] >> 2) & 3) | + (data[20] << 2) | + (data[19] << 10); + avg_lum += ((data[35] >> 4) & 3) | + (data[22] << 2) | + (data[21] << 10); + avg_lum += ((data[35] >> 6) & 3) | + (data[24] << 2) | + (data[23] << 10); + avg_lum += (data[36] & 3) | + (data[26] << 2) | + (data[25] << 10); + avg_lum += ((data[36] >> 2) & 3) | + (data[28] << 2) | + (data[27] << 10); + avg_lum += ((data[36] >> 4) & 3) | + (data[30] << 2) | + (data[29] << 10); + avg_lum += ((data[36] >> 6) & 3) | + (data[32] << 2) | + (data[31] << 10); + avg_lum += ((data[44] >> 4) & 3) | + (data[34] << 2) | + (data[33] << 10); + avg_lum >>= 9; + atomic_set(&sd->avg_lum, avg_lum); + gspca_frame_add(gspca_dev, LAST_PACKET, + frame, data, len); + return; + } + if (gspca_dev->last_packet_type == LAST_PACKET) { + if (gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv + & MODE_JPEG) { + gspca_frame_add(gspca_dev, FIRST_PACKET, frame, + sd->jpeg_hdr, JPEG_HDR_SZ); + gspca_frame_add(gspca_dev, INTER_PACKET, frame, + data, len); + } else { + gspca_frame_add(gspca_dev, FIRST_PACKET, frame, + data, len); + } + } else { + gspca_frame_add(gspca_dev, INTER_PACKET, frame, data, len); + } +} + +/* sub-driver description */ +static const struct sd_desc sd_desc = { + .name = MODULE_NAME, + .ctrls = sd_ctrls, + .nctrls = ARRAY_SIZE(sd_ctrls), + .config = sd_config, + .init = sd_init, + .start = sd_start, + .stopN = sd_stopN, + .stop0 = sd_stop0, + .pkt_scan = sd_pkt_scan, + .dq_callback = do_autoexposure, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .set_register = sd_dbg_s_register, + .get_register = sd_dbg_g_register, +#endif + .get_chip_ident = sd_chip_ident, +}; + +#define SN9C20X(sensor, i2c_addr, button_mask) \ + .driver_info = (button_mask << 16) \ + | (SENSOR_ ## sensor << 8) \ + | (i2c_addr) + +static const __devinitdata struct usb_device_id device_table[] = { + {USB_DEVICE(0x0c45, 0x6240), SN9C20X(MT9M001, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6242), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6248), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x624e), SN9C20X(SOI968, 0x30, 0x10)}, + {USB_DEVICE(0x0c45, 0x624f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6251), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6253), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6260), SN9C20X(OV7670, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x6270), SN9C20X(MT9VPRB, 0x00, 0)}, + {USB_DEVICE(0x0c45, 0x627b), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x627c), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0x0c45, 0x627f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x6280), SN9C20X(MT9M001, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6282), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0x0c45, 0x6288), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x628e), SN9C20X(SOI968, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x628f), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x62a0), SN9C20X(OV7670, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x62b0), SN9C20X(MT9VPRB, 0x00, 0)}, + {USB_DEVICE(0x0c45, 0x62b3), SN9C20X(OV9655, 0x30, 0)}, + {USB_DEVICE(0x0c45, 0x62bb), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0c45, 0x62bc), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0x045e, 0x00f4), SN9C20X(OV9650, 0x30, 0)}, + {USB_DEVICE(0x145f, 0x013d), SN9C20X(OV7660, 0x21, 0)}, + {USB_DEVICE(0x0458, 0x7029), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0610), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0611), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0613), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0618), SN9C20X(HV7131R, 0x11, 0)}, + {USB_DEVICE(0xa168, 0x0614), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0xa168, 0x0615), SN9C20X(MT9M111, 0x5d, 0)}, + {USB_DEVICE(0xa168, 0x0617), SN9C20X(MT9M111, 0x5d, 0)}, + {} +}; +MODULE_DEVICE_TABLE(usb, device_table); + +/* -- device connect -- */ +static int sd_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + return gspca_dev_probe(intf, id, &sd_desc, sizeof(struct sd), + THIS_MODULE); +} + +static void sd_disconnect(struct usb_interface *intf) +{ +#ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV + struct gspca_dev *gspca_dev = usb_get_intfdata(intf); + + sn9c20x_input_cleanup(gspca_dev); +#endif + + gspca_disconnect(intf); +} + +static struct usb_driver sd_driver = { + .name = MODULE_NAME, + .id_table = device_table, + .probe = sd_probe, + .disconnect = sd_disconnect, +#ifdef CONFIG_PM + .suspend = gspca_suspend, + .resume = gspca_resume, + .reset_resume = gspca_resume, +#endif +}; + +/* -- module insert / remove -- */ +static int __init sd_mod_init(void) +{ + int ret; + ret = usb_register(&sd_driver); + if (ret < 0) + return ret; + info("registered"); + return 0; +} +static void __exit sd_mod_exit(void) +{ + usb_deregister(&sd_driver); + info("deregistered"); +} + +module_init(sd_mod_init); +module_exit(sd_mod_exit); diff --git a/include/linux/videodev2.h b/include/linux/videodev2.h index 95846d988011..74f16876f38d 100644 --- a/include/linux/videodev2.h +++ b/include/linux/videodev2.h @@ -338,6 +338,7 @@ struct v4l2_pix_format { /* Vendor-specific formats */ #define V4L2_PIX_FMT_WNVA v4l2_fourcc('W', 'N', 'V', 'A') /* Winnov hw compress */ #define V4L2_PIX_FMT_SN9C10X v4l2_fourcc('S', '9', '1', '0') /* SN9C10x compression */ +#define V4L2_PIX_FMT_SN9C20X_I420 v4l2_fourcc('S', '9', '2', '0') /* SN9C20x YUV 4:2:0 */ #define V4L2_PIX_FMT_PWC1 v4l2_fourcc('P', 'W', 'C', '1') /* pwc older webcam */ #define V4L2_PIX_FMT_PWC2 v4l2_fourcc('P', 'W', 'C', '2') /* pwc newer webcam */ #define V4L2_PIX_FMT_ET61X251 v4l2_fourcc('E', '6', '2', '5') /* ET61X251 compression */ diff --git a/include/media/v4l2-chip-ident.h b/include/media/v4l2-chip-ident.h index 11a4a2d3e364..94e908c0d7a0 100644 --- a/include/media/v4l2-chip-ident.h +++ b/include/media/v4l2-chip-ident.h @@ -60,6 +60,10 @@ enum { V4L2_IDENT_OV7670 = 250, V4L2_IDENT_OV7720 = 251, V4L2_IDENT_OV7725 = 252, + V4L2_IDENT_OV7660 = 253, + V4L2_IDENT_OV9650 = 254, + V4L2_IDENT_OV9655 = 255, + V4L2_IDENT_SOI968 = 256, /* module saa7146: reserved range 300-309 */ V4L2_IDENT_SAA7146 = 300, @@ -161,6 +165,9 @@ enum { /* module tw9910: just ident 9910 */ V4L2_IDENT_TW9910 = 9910, + /* module sn9c20x: just ident 10000 */ + V4L2_IDENT_SN9C20X = 10000, + /* module msp3400: reserved range 34000-34999 and 44000-44999 */ V4L2_IDENT_MSPX4XX = 34000, /* generic MSPX4XX identifier, only use internally (tveeprom.c). */ @@ -237,6 +244,11 @@ enum { V4L2_IDENT_MT9V022IX7ATC = 45010, /* No way to detect "normal" I77ATx */ V4L2_IDENT_MT9V022IX7ATM = 45015, /* and "lead free" IA7ATx chips */ V4L2_IDENT_MT9T031 = 45020, + V4L2_IDENT_MT9V111 = 45031, + V4L2_IDENT_MT9V112 = 45032, + + /* HV7131R CMOS sensor: just ident 46000 */ + V4L2_IDENT_HV7131R = 46000, /* module cs53132a: just ident 53132 */ V4L2_IDENT_CS53l32A = 53132, -- cgit v1.2.3 From 3eb0237d445c23e9f46b11a07bce986eca450640 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sun, 19 Jul 2009 07:09:32 -0300 Subject: V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header). Signed-off-by: Julia Lawall Signed-off-by: Jean-Francois Moine Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/conex.c | 2 ++ drivers/media/video/gspca/mars.c | 2 ++ drivers/media/video/gspca/sonixj.c | 2 ++ drivers/media/video/gspca/spca500.c | 2 ++ drivers/media/video/gspca/stk014.c | 2 ++ drivers/media/video/gspca/sunplus.c | 2 ++ drivers/media/video/gspca/zc3xx.c | 2 ++ 7 files changed, 14 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/gspca/conex.c b/drivers/media/video/gspca/conex.c index 219cfa6fb877..8d48ea1742c2 100644 --- a/drivers/media/video/gspca/conex.c +++ b/drivers/media/video/gspca/conex.c @@ -846,6 +846,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/mars.c b/drivers/media/video/gspca/mars.c index 75e8d14e4ac7..de769caf013d 100644 --- a/drivers/media/video/gspca/mars.c +++ b/drivers/media/video/gspca/mars.c @@ -201,6 +201,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/sonixj.c b/drivers/media/video/gspca/sonixj.c index bad309b90cce..d6332ab80669 100644 --- a/drivers/media/video/gspca/sonixj.c +++ b/drivers/media/video/gspca/sonixj.c @@ -1737,6 +1737,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/spca500.c b/drivers/media/video/gspca/spca500.c index 8806b2ff82be..fab7ef85a6c1 100644 --- a/drivers/media/video/gspca/spca500.c +++ b/drivers/media/video/gspca/spca500.c @@ -670,6 +670,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/stk014.c b/drivers/media/video/gspca/stk014.c index f25be20cf1a6..47628964801e 100644 --- a/drivers/media/video/gspca/stk014.c +++ b/drivers/media/video/gspca/stk014.c @@ -333,6 +333,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/sunplus.c b/drivers/media/video/gspca/sunplus.c index 9623f294bdac..5127bbf9dd26 100644 --- a/drivers/media/video/gspca/sunplus.c +++ b/drivers/media/video/gspca/sunplus.c @@ -973,6 +973,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x22); /* JPEG 411 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); diff --git a/drivers/media/video/gspca/zc3xx.c b/drivers/media/video/gspca/zc3xx.c index 08422d315e68..3d2756f7874a 100644 --- a/drivers/media/video/gspca/zc3xx.c +++ b/drivers/media/video/gspca/zc3xx.c @@ -7243,6 +7243,8 @@ static int sd_start(struct gspca_dev *gspca_dev) /* create the JPEG header */ sd->jpeg_hdr = kmalloc(JPEG_HDR_SZ, GFP_KERNEL); + if (!sd->jpeg_hdr) + return -ENOMEM; jpeg_define(sd->jpeg_hdr, gspca_dev->height, gspca_dev->width, 0x21); /* JPEG 422 */ jpeg_set_qual(sd->jpeg_hdr, sd->quality); -- cgit v1.2.3 From c15b95edb98f184e73f756511a60a7994cd9d840 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sun, 19 Jul 2009 18:03:23 -0300 Subject: V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers This is not just pure cosmetic, since the order affects the out-of-tree module build at the -hg development tree. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/gspca/sn9c20x.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/gspca/sn9c20x.c b/drivers/media/video/gspca/sn9c20x.c index 78ab26ceb90e..fcfbbd329b4c 100644 --- a/drivers/media/video/gspca/sn9c20x.c +++ b/drivers/media/video/gspca/sn9c20x.c @@ -18,10 +18,6 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include "gspca.h" -#include "jpeg.h" - -#include #ifdef CONFIG_USB_GSPCA_SN9C20X_EVDEV #include #include @@ -29,6 +25,11 @@ #include #endif +#include "gspca.h" +#include "jpeg.h" + +#include + MODULE_AUTHOR("Brian Johnson , " "microdia project "); MODULE_DESCRIPTION("GSPCA/SN9C20X USB Camera Driver"); -- cgit v1.2.3 From 68b7f7616add4b1de0fe75015ba3884d2d9ff796 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Thu, 11 Jun 2009 19:31:22 -0300 Subject: V4L/DVB (12291): b2c2: fix frontends compiled into kernel A recent patch didn't take into account that frontends can be compiled into the kernel. Or that frontends compiled as modules can't be used by the b2c2 driver if it is not a module itself. Some frontends require multiple drivers, e.g. a demod driver and a tuner driver. The code for the frontend support was getting added if the demod driver was available. Change this to also require any needed tuner or SEC drivers as well. Signed-off-by: Trent Piepho Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/b2c2/flexcop-fe-tuner.c | 67 +++++++++++++++++-------------- 1 file changed, 37 insertions(+), 30 deletions(-) (limited to 'drivers') diff --git a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c index efb4a6c2b57a..9a6307a347b2 100644 --- a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c +++ b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c @@ -20,8 +20,14 @@ #include "tuner-simple.h" #include "stv0297.h" + +/* Can we use the specified front-end? Remember that if we are compiled + * into the kernel we can't call code that's in modules. */ +#define FE_SUPPORTED(fe) (defined(CONFIG_DVB_##fe) || \ + (defined(CONFIG_DVB_##fe##_MODULE) && defined(MODULE))) + /* lnb control */ -#if defined(CONFIG_DVB_MT312_MODULE) || defined(CONFIG_DVB_STV0299_MODULE) +#if FE_SUPPORTED(MT312) || FE_SUPPORTED(STV0299) static int flexcop_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage) { struct flexcop_device *fc = fe->dvb->priv; @@ -49,8 +55,7 @@ static int flexcop_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage } #endif -#if defined(CONFIG_DVB_S5H1420_MODULE) || defined(CONFIG_DVB_STV0299_MODULE) \ - || defined(CONFIG_DVB_MT312_MODULE) +#if FE_SUPPORTED(S5H1420) || FE_SUPPORTED(STV0299) || FE_SUPPORTED(MT312) static int flexcop_sleep(struct dvb_frontend* fe) { struct flexcop_device *fc = fe->dvb->priv; @@ -61,7 +66,7 @@ static int flexcop_sleep(struct dvb_frontend* fe) #endif /* SkyStar2 DVB-S rev 2.3 */ -#if defined(CONFIG_DVB_MT312_MODULE) +#if FE_SUPPORTED(MT312) static int flexcop_set_tone(struct dvb_frontend *fe, fe_sec_tone_mode_t tone) { /* u16 wz_half_period_for_45_mhz[] = { 0x01ff, 0x0154, 0x00ff, 0x00cc }; */ @@ -193,10 +198,12 @@ static int skystar2_rev23_attach(struct flexcop_device *fc, } return 0; } +#else +#define skystar2_rev23_attach NULL #endif /* SkyStar2 DVB-S rev 2.6 */ -#if defined(CONFIG_DVB_STV0299_MODULE) +#if FE_SUPPORTED(STV0299) static int samsung_tbmu24112_set_symbol_rate(struct dvb_frontend *fe, u32 srate, u32 ratio) { @@ -321,10 +328,12 @@ static int skystar2_rev26_attach(struct flexcop_device *fc, } return 0; } +#else +#define skystar2_rev26_attach NULL #endif /* SkyStar2 DVB-S rev 2.7 */ -#if defined(CONFIG_DVB_S5H1420_MODULE) +#if FE_SUPPORTED(S5H1420) && FE_SUPPORTED(ISL6421) && FE_SUPPORTED(TUNER_ITD1000) static struct s5h1420_config skystar2_rev2_7_s5h1420_config = { .demod_address = 0x53, .invert = 1, @@ -385,10 +394,12 @@ fail: fc->fc_i2c_adap[0].no_base_addr = 0; return 0; } +#else +#define skystar2_rev27_attach NULL #endif /* SkyStar2 rev 2.8 */ -#if defined(CONFIG_DVB_CX24123_MODULE) +#if FE_SUPPORTED(CX24123) && FE_SUPPORTED(ISL6421) && FE_SUPPORTED(TUNER_CX24113) static struct cx24123_config skystar2_rev2_8_cx24123_config = { .demod_address = 0x55, .dont_use_pll = 1, @@ -433,10 +444,12 @@ static int skystar2_rev28_attach(struct flexcop_device *fc, * IR-receiver (PIC16F818) - but the card has no input for that ??? */ return 1; } +#else +#define skystar2_rev28_attach NULL #endif /* AirStar DVB-T */ -#if defined(CONFIG_DVB_MT352_MODULE) +#if FE_SUPPORTED(MT352) static int samsung_tdtc9251dh0_demod_init(struct dvb_frontend *fe) { static u8 mt352_clock_config[] = { 0x89, 0x18, 0x2d }; @@ -495,10 +508,12 @@ static int airstar_dvbt_attach(struct flexcop_device *fc, } return 0; } +#else +#define airstar_dvbt_attach NULL #endif /* AirStar ATSC 1st generation */ -#if defined(CONFIG_DVB_BCM3510_MODULE) +#if FE_SUPPORTED(BCM3510) static int flexcop_fe_request_firmware(struct dvb_frontend *fe, const struct firmware **fw, char* name) { @@ -517,10 +532,12 @@ static int airstar_atsc1_attach(struct flexcop_device *fc, fc->fe = dvb_attach(bcm3510_attach, &air2pc_atsc_first_gen_config, i2c); return fc->fe != NULL; } +#else +#define airstar_atsc1_attach NULL #endif /* AirStar ATSC 2nd generation */ -#if defined(CONFIG_DVB_NXT200X_MODULE) +#if FE_SUPPORTED(NXT200X) && FE_SUPPORTED(PLL) static struct nxt200x_config samsung_tbmv_config = { .demod_address = 0x0a, }; @@ -535,10 +552,12 @@ static int airstar_atsc2_attach(struct flexcop_device *fc, return !!dvb_attach(dvb_pll_attach, fc->fe, 0x61, NULL, DVB_PLL_SAMSUNG_TBMV); } +#else +#define airstar_atsc2_attach NULL #endif /* AirStar ATSC 3rd generation */ -#if defined(CONFIG_DVB_LGDT330X_MODULE) +#if FE_SUPPORTED(LGDT330X) static struct lgdt330x_config air2pc_atsc_hd5000_config = { .demod_address = 0x59, .demod_chip = LGDT3303, @@ -556,10 +575,12 @@ static int airstar_atsc3_attach(struct flexcop_device *fc, return !!dvb_attach(simple_tuner_attach, fc->fe, i2c, 0x61, TUNER_LG_TDVS_H06XF); } +#else +#define airstar_atsc3_attach NULL #endif /* CableStar2 DVB-C */ -#if defined(CONFIG_DVB_STV0297_MODULE) +#if FE_SUPPORTED(STV0297) static int alps_tdee4_stv0297_tuner_set_params(struct dvb_frontend* fe, struct dvb_frontend_parameters *fep) { @@ -698,39 +719,23 @@ static int cablestar2_attach(struct flexcop_device *fc, fc->fe->ops.tuner_ops.set_params = alps_tdee4_stv0297_tuner_set_params; return 1; } +#else +#define cablestar2_attach NULL #endif static struct { flexcop_device_type_t type; int (*attach)(struct flexcop_device *, struct i2c_adapter *); } flexcop_frontends[] = { -#if defined(CONFIG_DVB_S5H1420_MODULE) { FC_SKY_REV27, skystar2_rev27_attach }, -#endif -#if defined(CONFIG_DVB_CX24123_MODULE) { FC_SKY_REV28, skystar2_rev28_attach }, -#endif -#if defined(CONFIG_DVB_STV0299_MODULE) { FC_SKY_REV26, skystar2_rev26_attach }, -#endif -#if defined(CONFIG_DVB_MT352_MODULE) { FC_AIR_DVBT, airstar_dvbt_attach }, -#endif -#if defined(CONFIG_DVB_NXT200X_MODULE) { FC_AIR_ATSC2, airstar_atsc2_attach }, -#endif -#if defined(CONFIG_DVB_LGDT330X_MODULE) { FC_AIR_ATSC3, airstar_atsc3_attach }, -#endif -#if defined(CONFIG_DVB_BCM3510_MODULE) { FC_AIR_ATSC1, airstar_atsc1_attach }, -#endif -#if defined(CONFIG_DVB_STV0297_MODULE) { FC_CABLE, cablestar2_attach }, -#endif -#if defined(CONFIG_DVB_MT312_MODULE) { FC_SKY_REV23, skystar2_rev23_attach }, -#endif }; /* try to figure out the frontend */ @@ -738,6 +743,8 @@ int flexcop_frontend_init(struct flexcop_device *fc) { int i; for (i = 0; i < ARRAY_SIZE(flexcop_frontends); i++) { + if (!flexcop_frontends[i].attach) + continue; /* type needs to be set before, because of some workarounds * done based on the probed card type */ fc->dev_type = flexcop_frontends[i].type; -- cgit v1.2.3 From 2c90577841a76f1935ff3437ffb552b41f5c28fa Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Mon, 20 Jul 2009 08:14:17 -0300 Subject: V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can check whether it really is a tda9840, but the tuner can't. So the tvaudio module must be loaded before the tuner module. This was also the case for 2.6.29, but the order was swapped in 2.6.30. Thanks to Krzysztof Grygiencz for reporting and testing this. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/bt8xx/bttv-cards.c | 92 +++++++++++++++++---------------- drivers/media/video/bt8xx/bttv-driver.c | 1 + drivers/media/video/bt8xx/bttv.h | 1 + 3 files changed, 50 insertions(+), 44 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c index fdb4adff3d28..ca6558c394be 100644 --- a/drivers/media/video/bt8xx/bttv-cards.c +++ b/drivers/media/video/bt8xx/bttv-cards.c @@ -3324,8 +3324,6 @@ void __devinit bttv_init_card1(struct bttv *btv) /* initialization part two -- after registering i2c bus */ void __devinit bttv_init_card2(struct bttv *btv) { - int addr=ADDR_UNSET; - btv->tuner_type = UNSET; if (BTTV_BOARD_UNKNOWN == btv->c.type) { @@ -3470,9 +3468,6 @@ void __devinit bttv_init_card2(struct bttv *btv) btv->pll.pll_current = -1; /* tuner configuration (from card list / autodetect / insmod option) */ - if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) - addr = bttv_tvcards[btv->c.type].tuner_addr; - if (UNSET != bttv_tvcards[btv->c.type].tuner_type) if (UNSET == btv->tuner_type) btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type; @@ -3496,40 +3491,6 @@ void __devinit bttv_init_card2(struct bttv *btv) if (UNSET == btv->tuner_type) btv->tuner_type = TUNER_ABSENT; - if (btv->tuner_type != TUNER_ABSENT) { - struct tuner_setup tun_setup; - - /* Load tuner module before issuing tuner config call! */ - if (bttv_tvcards[btv->c.type].has_radio) - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_RADIO)); - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); - v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, - &btv->c.i2c_adap, "tuner", "tuner", - v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); - - tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV; - tun_setup.type = btv->tuner_type; - tun_setup.addr = addr; - - if (bttv_tvcards[btv->c.type].has_radio) - tun_setup.mode_mask |= T_RADIO; - - bttv_call_all(btv, tuner, s_type_addr, &tun_setup); - } - - if (btv->tda9887_conf) { - struct v4l2_priv_tun_config tda9887_cfg; - - tda9887_cfg.tuner = TUNER_TDA9887; - tda9887_cfg.priv = &btv->tda9887_conf; - - bttv_call_all(btv, tuner, s_config, &tda9887_cfg); - } - btv->dig = bttv_tvcards[btv->c.type].has_dig_in ? bttv_tvcards[btv->c.type].video_inputs - 1 : UNSET; btv->svhs = bttv_tvcards[btv->c.type].svhs == NO_SVHS ? @@ -3540,15 +3501,15 @@ void __devinit bttv_init_card2(struct bttv *btv) btv->has_remote = remote[btv->c.nr]; if (bttv_tvcards[btv->c.type].has_radio) - btv->has_radio=1; + btv->has_radio = 1; if (bttv_tvcards[btv->c.type].has_remote) - btv->has_remote=1; + btv->has_remote = 1; if (!bttv_tvcards[btv->c.type].no_gpioirq) - btv->gpioirq=1; + btv->gpioirq = 1; if (bttv_tvcards[btv->c.type].volume_gpio) - btv->volume_gpio=bttv_tvcards[btv->c.type].volume_gpio; + btv->volume_gpio = bttv_tvcards[btv->c.type].volume_gpio; if (bttv_tvcards[btv->c.type].audio_mode_gpio) - btv->audio_mode_gpio=bttv_tvcards[btv->c.type].audio_mode_gpio; + btv->audio_mode_gpio = bttv_tvcards[btv->c.type].audio_mode_gpio; if (btv->tuner_type == TUNER_ABSENT) return; /* no tuner or related drivers to load */ @@ -3666,6 +3627,49 @@ no_audio: } +/* initialize the tuner */ +void __devinit bttv_init_tuner(struct bttv *btv) +{ + int addr = ADDR_UNSET; + + if (ADDR_UNSET != bttv_tvcards[btv->c.type].tuner_addr) + addr = bttv_tvcards[btv->c.type].tuner_addr; + + if (btv->tuner_type != TUNER_ABSENT) { + struct tuner_setup tun_setup; + + /* Load tuner module before issuing tuner config call! */ + if (bttv_tvcards[btv->c.type].has_radio) + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_RADIO)); + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_DEMOD)); + v4l2_i2c_new_probed_subdev(&btv->c.v4l2_dev, + &btv->c.i2c_adap, "tuner", "tuner", + v4l2_i2c_tuner_addrs(ADDRS_TV_WITH_DEMOD)); + + tun_setup.mode_mask = T_ANALOG_TV | T_DIGITAL_TV; + tun_setup.type = btv->tuner_type; + tun_setup.addr = addr; + + if (bttv_tvcards[btv->c.type].has_radio) + tun_setup.mode_mask |= T_RADIO; + + bttv_call_all(btv, tuner, s_type_addr, &tun_setup); + } + + if (btv->tda9887_conf) { + struct v4l2_priv_tun_config tda9887_cfg; + + tda9887_cfg.tuner = TUNER_TDA9887; + tda9887_cfg.priv = &btv->tda9887_conf; + + bttv_call_all(btv, tuner, s_config, &tda9887_cfg); + } +} + /* ----------------------------------------------------------------------- */ static void modtec_eeprom(struct bttv *btv) diff --git a/drivers/media/video/bt8xx/bttv-driver.c b/drivers/media/video/bt8xx/bttv-driver.c index d147d29bb0d3..8cc6dd28d6a7 100644 --- a/drivers/media/video/bt8xx/bttv-driver.c +++ b/drivers/media/video/bt8xx/bttv-driver.c @@ -4419,6 +4419,7 @@ static int __devinit bttv_probe(struct pci_dev *dev, /* some card-specific stuff (needs working i2c) */ bttv_init_card2(btv); + bttv_init_tuner(btv); init_irqreg(btv); /* register video4linux + input */ diff --git a/drivers/media/video/bt8xx/bttv.h b/drivers/media/video/bt8xx/bttv.h index 3d36daf206f3..3ec2402c6b4a 100644 --- a/drivers/media/video/bt8xx/bttv.h +++ b/drivers/media/video/bt8xx/bttv.h @@ -283,6 +283,7 @@ extern struct tvcard bttv_tvcards[]; extern void bttv_idcard(struct bttv *btv); extern void bttv_init_card1(struct bttv *btv); extern void bttv_init_card2(struct bttv *btv); +extern void bttv_init_tuner(struct bttv *btv); /* card-specific funtions */ extern void tea5757_set_freq(struct bttv *btv, unsigned short freq); -- cgit v1.2.3 From 12a34cc8a9a49219ab643c8ec329078eec272b47 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 19 Jul 2009 18:19:18 -0300 Subject: V4L/DVB (12302): cx23885-417: fix broken IOCTL handling IOCTLS will never get handled if we dont connect video_ioctl2 to mpeg_fops.ioctl Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index 428f0c45e6b7..2ea7181ae8fb 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -1677,6 +1677,7 @@ static struct v4l2_file_operations mpeg_fops = { .read = mpeg_read, .poll = mpeg_poll, .mmap = mpeg_mmap, + .ioctl = video_ioctl2, }; static const struct v4l2_ioctl_ops mpeg_ioctl_ops = { -- cgit v1.2.3 From ca4e771f7b878b7bab02dedb539f7742f9b4f50e Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 19 Jul 2009 17:55:35 -0300 Subject: V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro When enabling debug with v4l_debug set to 2 or greater, the driver OOPS's on startup. Checks dev pointer before dereferencing, in order to prevent this OOPS. Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index 2ea7181ae8fb..e0cf21e0b1bf 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -58,7 +58,8 @@ MODULE_PARM_DESC(v4l_debug, "enable V4L debug messages"); #define dprintk(level, fmt, arg...)\ do { if (v4l_debug >= level) \ - printk(KERN_DEBUG "%s: " fmt, dev->name , ## arg);\ + printk(KERN_DEBUG "%s: " fmt, \ + (dev) ? dev->name : "cx23885[?]", ## arg); \ } while (0) static struct cx23885_tvnorm cx23885_tvnorms[] = { -- cgit v1.2.3 From 7194e6f9c083e87171ddfc8b746f05e007f58132 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 24 Jul 2009 17:05:00 +0300 Subject: UBI: fix double free on error path If we fail in 'ubi_eba_init_scan()', we free 'ubi->volumes[i]->eba_tbl' in there, but also later free it in 'free_internal_volumes()'. Fix this by assigning NULL to 'ubi->volumes[i]->eba_tbl' after it is freed. Signed-off-by: Adrian Hunter Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/eba.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/mtd/ubi/eba.c b/drivers/mtd/ubi/eba.c index 0f2034c3ed2f..e4d9ef0c965a 100644 --- a/drivers/mtd/ubi/eba.c +++ b/drivers/mtd/ubi/eba.c @@ -1254,6 +1254,7 @@ out_free: if (!ubi->volumes[i]) continue; kfree(ubi->volumes[i]->eba_tbl); + ubi->volumes[i]->eba_tbl = NULL; } return err; } -- cgit v1.2.3 From 32bc4820287a1a03982979515949e8ea56eac641 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Fri, 24 Jul 2009 19:16:04 +0300 Subject: UBI: compatible fallback in absense of sequence numbers Fall back onto thinking everything's OK if either of the sequence numbers we are asked to compare is zero, which is what was used before sequence numbers were introduced. [ Artem: modified the patch to be applicable to upstream UBI, added big comment ] Signed-off-by: Adrian Hunter Signed-off-by: Phil Carmody Signed-off-by: Artem Bityutskiy --- drivers/mtd/ubi/scan.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c index a423131b6171..b847745394b4 100644 --- a/drivers/mtd/ubi/scan.c +++ b/drivers/mtd/ubi/scan.c @@ -781,11 +781,22 @@ static int process_eb(struct ubi_device *ubi, struct ubi_scan_info *si, return -EINVAL; } + /* + * Make sure that all PEBs have the same image sequence number. + * This allows us to detect situations when users flash UBI + * images incorrectly, so that the flash has the new UBI image + * and leftovers from the old one. This feature was added + * relatively recently, and the sequence number was always + * zero, because old UBI implementations always set it to zero. + * For this reasons, we do not panic if some PEBs have zero + * sequence number, while other PEBs have non-zero sequence + * number. + */ image_seq = be32_to_cpu(ech->image_seq); if (!si->image_seq_set) { ubi->image_seq = image_seq; si->image_seq_set = 1; - } else if (ubi->image_seq != image_seq) { + } else if (ubi->image_seq && ubi->image_seq != image_seq) { ubi_err("bad image sequence number %d in PEB %d, " "expected %d", image_seq, pnum, ubi->image_seq); ubi_dbg_dump_ec_hdr(ech); -- cgit v1.2.3 From f83284fe209b1d143244bf462abf1b414eb7b62a Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 07:41:12 +0000 Subject: fealnx: Write outside array bounds phy_idx is checked to be < 4, but np->phys[] is 2 elements long Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/fealnx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/fealnx.c b/drivers/net/fealnx.c index 891be28a7d4f..ee51557e942b 100644 --- a/drivers/net/fealnx.c +++ b/drivers/net/fealnx.c @@ -584,7 +584,8 @@ static int __devinit fealnx_init_one(struct pci_dev *pdev, if (np->flags == HAS_MII_XCVR) { int phy, phy_idx = 0; - for (phy = 1; phy < 32 && phy_idx < 4; phy++) { + for (phy = 1; phy < 32 && phy_idx < ARRAY_SIZE(np->phys); + phy++) { int mii_status = mdio_read(dev, phy, 1); if (mii_status != 0xffff && mii_status != 0x0000) { -- cgit v1.2.3 From 3b73e79b0dcc86f8bec68a34b7fb812eec953f34 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 12:01:50 +0000 Subject: at1700: Read buffer overflow loop bound looks to be wrong, for an array of length 8 Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/at1700.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/at1700.c b/drivers/net/at1700.c index 18b566ad4fd1..cf30e278f182 100644 --- a/drivers/net/at1700.c +++ b/drivers/net/at1700.c @@ -318,7 +318,7 @@ static int __init at1700_probe1(struct net_device *dev, int ioaddr) pos3 = mca_read_stored_pos( slot, 3 ); pos4 = mca_read_stored_pos( slot, 4 ); - for (l_i = 0; l_i < 0x09; l_i++) + for (l_i = 0; l_i < 8; l_i++) if (( pos3 & 0x07) == at1700_ioaddr_pattern[l_i]) break; ioaddr = at1700_mca_probe_list[l_i]; -- cgit v1.2.3 From c65d3198addb1a2862d4b88bc2a74ac9cbed66f9 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 25 Jul 2009 12:38:33 +0000 Subject: tokenring: Read buffer overflow io[i] is read before the bounds check on i, order should be reversed Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/tokenring/ibmtr.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/tokenring/ibmtr.c b/drivers/net/tokenring/ibmtr.c index 9d896116cf76..08a6c41c1599 100644 --- a/drivers/net/tokenring/ibmtr.c +++ b/drivers/net/tokenring/ibmtr.c @@ -1912,7 +1912,7 @@ static int __init ibmtr_init(void) find_turbo_adapters(io); - for (i = 0; io[i] && (i < IBMTR_MAX_ADAPTERS); i++) { + for (i = 0; i < IBMTR_MAX_ADAPTERS && io[i]; i++) { struct net_device *dev; irq[i] = 0; mem[i] = 0; -- cgit v1.2.3 From d513d018e2236930b6163241bbdce64d2c0de49e Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 26 Jul 2009 18:53:17 -0700 Subject: eepro: Read buffer overflow io[i] is read before the bounds check on i, order should be reversed Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/eepro.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/eepro.c b/drivers/net/eepro.c index cc2ab6412c73..4f7003485348 100644 --- a/drivers/net/eepro.c +++ b/drivers/net/eepro.c @@ -1784,7 +1784,7 @@ int __init init_module(void) printk(KERN_INFO "eepro_init_module: Auto-detecting boards (May God protect us...)\n"); } - for (i = 0; io[i] != -1 && i < MAX_EEPRO; i++) { + for (i = 0; i < MAX_EEPRO && io[i] != -1; i++) { dev = alloc_etherdev(sizeof(struct eepro_local)); if (!dev) break; -- cgit v1.2.3 From 4a29f396429132dc59f1856ea6cfc860a1955fa1 Mon Sep 17 00:00:00 2001 From: Alessandro Rubini Date: Wed, 22 Jul 2009 12:49:08 +0000 Subject: smc91x.h: add config for Nomadik evaluation kit Signed-off-by: Alessandro Rubini Acked-by: Andrea Gallo Signed-off-by: David S. Miller --- drivers/net/smc91x.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h index f1f773b17fe1..57a159fac99f 100644 --- a/drivers/net/smc91x.h +++ b/drivers/net/smc91x.h @@ -186,7 +186,8 @@ static inline void SMC_outw(u16 val, void __iomem *ioaddr, int reg) #define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l)) #define SMC_IRQ_FLAGS (-1) /* from resource */ -#elif defined(CONFIG_MACH_LOGICPD_PXA270) +#elif defined(CONFIG_MACH_LOGICPD_PXA270) \ + || defined(CONFIG_MACH_NOMADIK_8815NHK) #define SMC_CAN_USE_8BIT 0 #define SMC_CAN_USE_16BIT 1 -- cgit v1.2.3 From c8a5a658b826508c7c61b57e9a590f7b8760fb51 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Sun, 26 Jul 2009 20:17:21 -0700 Subject: netxen: reset ring consumer during cleanup Reset consumer of status rings to 0 when cleaning up sw resources. Status rings are not deleted during suspend since they have napi objects. This ensures correct rx processing across suspen-resume. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_init.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 5d3343ef3d86..7acf204e38c9 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -184,6 +184,13 @@ void netxen_free_sw_resources(struct netxen_adapter *adapter) kfree(recv_ctx->rds_rings); skip_rds: + if (recv_ctx->sds_rings == NULL) + goto skip_sds; + + for(ring = 0; ring < adapter->max_sds_rings; ring++) + recv_ctx->sds_rings[ring].consumer = 0; + +skip_sds: if (adapter->tx_ring == NULL) return; -- cgit v1.2.3 From ca52efd5490f97f396d3c5863ba714624f272033 Mon Sep 17 00:00:00 2001 From: françois romieu Date: Fri, 24 Jul 2009 12:34:19 +0000 Subject: r8169: WakeOnLan fix for the 8168 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit More stuff for http://bugzilla.kernel.org/show_bug.cgi?id=9512 Some 8168 are unable to WoL when receiving is not enabled (plain old 8169 do not seem to care). It is not exactly pretty to leave the receiver enabled but we should now enable DMA late enough for it to be safe. Some late stage boot failure due to pxe and friends may benefit from the delayed enabling of bus-mastering as well. Signed-off-by: Francois Romieu Tested-by: Jaromír Cápík Cc: Edward Hsu --- drivers/net/r8169.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index 4b53b58d75fc..b82780d805f5 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -2060,8 +2060,6 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } } - pci_set_master(pdev); - /* ioremap MMIO region */ ioaddr = ioremap(pci_resource_start(pdev, region), R8169_REGS_SIZE); if (!ioaddr) { @@ -2089,6 +2087,8 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) RTL_W16(IntrStatus, 0xffff); + pci_set_master(pdev); + /* Identify chip attached to board */ rtl8169_get_mac_version(tp, ioaddr); @@ -3874,6 +3874,15 @@ static void rtl_shutdown(struct pci_dev *pdev) spin_unlock_irq(&tp->lock); if (system_state == SYSTEM_POWER_OFF) { + /* WoL fails with some 8168 when the receiver is disabled. */ + if (tp->features & RTL_FEATURE_WOL) { + pci_clear_master(pdev); + + RTL_W8(ChipCmd, CmdRxEnb); + /* PCI commit */ + RTL_R8(ChipCmd); + } + pci_wake_from_d3(pdev, true); pci_set_power_state(pdev, PCI_D3hot); } -- cgit v1.2.3 From 8bae1b2b13beb4cf4c0f119f97640503c2b74b0f Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Thu, 23 Jul 2009 18:00:39 +0000 Subject: ixgbe: fix for 82599 errata marking UDP checksum errors There is an 82599 errata that UDP frames with a zero checksum are incorrectly marked as checksum invalid by the hardware. This was leading to misleading hw_csum_rx_error counts. This patch adds a test around this counter increase for this condition. Signed-off-by: Don Skidmore Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 68877599f6db..200454f30f6a 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -511,8 +511,11 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector, * @skb: skb currently being received and modified **/ static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter, - u32 status_err, struct sk_buff *skb) + union ixgbe_adv_rx_desc *rx_desc, + struct sk_buff *skb) { + u32 status_err = le32_to_cpu(rx_desc->wb.upper.status_error); + skb->ip_summed = CHECKSUM_NONE; /* Rx csum disabled */ @@ -530,6 +533,16 @@ static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter, return; if (status_err & IXGBE_RXDADV_ERR_TCPE) { + u16 pkt_info = rx_desc->wb.lower.lo_dword.hs_rss.pkt_info; + + /* + * 82599 errata, UDP frames with a 0 checksum can be marked as + * checksum errors. + */ + if ((pkt_info & IXGBE_RXDADV_PKTTYPE_UDP) && + (adapter->hw.mac.type == ixgbe_mac_82599EB)) + return; + adapter->hw_csum_rx_error++; return; } @@ -803,7 +816,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, goto next_desc; } - ixgbe_rx_checksum(adapter, staterr, skb); + ixgbe_rx_checksum(adapter, rx_desc, skb); /* probably a little skewed due to removing CRC */ total_rx_bytes += skb->len; -- cgit v1.2.3 From 4afcd2dcc6d89da696fc9d469a909adafa9d3636 Mon Sep 17 00:00:00 2001 From: Wan Wei Date: Mon, 27 Jul 2009 14:34:15 +0200 Subject: amd64_edac: read the right F2 maskoffset reg Signed-off-by: Wan Wei Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 858fe6037223..24964c1d0af9 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -970,7 +970,7 @@ static void amd64_read_dct_base_mask(struct amd64_pvt *pvt) } for (cs = 0; cs < pvt->num_dcsm; cs++) { - reg = K8_DCSB0 + (cs * 4); + reg = K8_DCSM0 + (cs * 4); err = pci_read_config_dword(pvt->dram_f2_ctl, reg, &pvt->dcsm0[cs]); if (unlikely(err)) -- cgit v1.2.3 From 6d7760a88c25057c2c2243e5dfe2d731064bd31d Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Mon, 27 Jul 2009 11:25:58 -0700 Subject: cnic: Fix ISCSI_KEVENT_IF_DOWN message handling. When a net device goes down or when the bnx2i driver is unloaded, the code was not generating the ISCSI_KEVENT_IF_DOWN message properly and this could cause the userspace driver to crash. This is fixed by sending the message properly in the shutdown path. cnic_uio_stop() is also added to send the message when bnx2i is unregistering. Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/cnic.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4d1515f45ba2..4869d77cbe91 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -227,7 +227,7 @@ static int cnic_send_nlmsg(struct cnic_local *cp, u32 type, } rcu_read_lock(); - ulp_ops = rcu_dereference(cp->ulp_ops[CNIC_ULP_ISCSI]); + ulp_ops = rcu_dereference(cnic_ulp_tbl[CNIC_ULP_ISCSI]); if (ulp_ops) ulp_ops->iscsi_nl_send_msg(cp->dev, msg_type, buf, len); rcu_read_unlock(); @@ -319,6 +319,20 @@ static int cnic_abort_prep(struct cnic_sock *csk) return 0; } +static void cnic_uio_stop(void) +{ + struct cnic_dev *dev; + + read_lock(&cnic_dev_lock); + list_for_each_entry(dev, &cnic_dev_list, list) { + struct cnic_local *cp = dev->cnic_priv; + + if (cp->cnic_uinfo) + cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); + } + read_unlock(&cnic_dev_lock); +} + int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) { struct cnic_dev *dev; @@ -390,6 +404,9 @@ int cnic_unregister_driver(int ulp_type) } read_unlock(&cnic_dev_lock); + if (ulp_type == CNIC_ULP_ISCSI) + cnic_uio_stop(); + rcu_assign_pointer(cnic_ulp_tbl[ulp_type], NULL); mutex_unlock(&cnic_lock); @@ -632,7 +649,6 @@ static void cnic_free_resc(struct cnic_dev *dev) int i = 0; if (cp->cnic_uinfo) { - cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); while (cp->uio_dev != -1 && i < 15) { msleep(100); i++; @@ -1057,6 +1073,9 @@ static void cnic_ulp_stop(struct cnic_dev *dev) struct cnic_local *cp = dev->cnic_priv; int if_type; + if (cp->cnic_uinfo) + cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); + rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; -- cgit v1.2.3 From 3995bd9332a51b626237d6671cfeb7235e6c1305 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 24 Jul 2009 11:13:14 -0700 Subject: iwlwifi: fix TX queue race I had a problem on 4965 hardware (well, probably other hardware too, but others don't survive my stress testing right now, unfortunately) where the driver was sending invalid commands to the device, but no such thing could be seen from the driver's point of view. I could reproduce this fairly easily by sending multiple TCP streams with iperf on different TIDs, though sometimes a single iperf stream was sufficient. It even happened with a single core, but I have forced preemption turned on. The culprit was a queue overrun, where we advanced the queue's write pointer over the read pointer. After careful analysis I've come to the conclusion that the cause is a race condition between iwlwifi and mac80211. mac80211, of course, checks whether the queue is stopped, before transmitting a frame. This effectively looks like this: lock(queues) if (stopped(queue)) { unlock(queues) return busy; } unlock(queues) ... <-- this place will be important there is some more code here drv_tx(frame) The driver, on the other hand, can stop and start queues, which does lock(queues) mark_running/stopped(queue) unlock(queues) [if marked running: wake up tasklet to send pending frames] Now, however, once the driver starts the queue, mac80211 can see that and end up at the marked place above, at which point for some reason the driver seems to stop the queue again (I don't understand that) and then we end up transmitting while the queue is actually full. Now, this shouldn't actually matter much, but for some reason I've seen it happen multiple times in a row and the queue actually overflows, at which point the queue bites itself in the tail and things go completely wrong. This patch fixes this by just dropping the packet should this have happened, and making the lock in iwlwifi cover everything so iwlwifi can't race against itself (dropping the lock there might make it more likely, but it did seem to happen without that too). Since we can't hold the lock across drv_tx() above, I see no way to fix this in mac80211, but I also don't understand why I haven't seen this before -- maybe I just never stress tested it this badly. With this patch, the device has survived many minutes of simultanously sending two iperf streams on different TIDs with combined throughput of about 60 Mbps. Signed-off-by: Johannes Berg Signed-off-by: Reinette Chatre Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 9bbeec9427f0..5febb3186365 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -720,8 +720,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) goto drop_unlock; } - spin_unlock_irqrestore(&priv->lock, flags); - hdr_len = ieee80211_hdrlen(fc); /* Find (or create) index into station table for destination station */ @@ -729,7 +727,7 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) if (sta_id == IWL_INVALID_STATION) { IWL_DEBUG_DROP(priv, "Dropping - INVALID STATION: %pM\n", hdr->addr1); - goto drop; + goto drop_unlock; } IWL_DEBUG_TX(priv, "station Id %d\n", sta_id); @@ -750,14 +748,17 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) txq_id = priv->stations[sta_id].tid[tid].agg.txq_id; swq_id = iwl_virtual_agg_queue_num(swq_id, txq_id); } - priv->stations[sta_id].tid[tid].tfds_in_queue++; } txq = &priv->txq[txq_id]; q = &txq->q; txq->swq_id = swq_id; - spin_lock_irqsave(&priv->lock, flags); + if (unlikely(iwl_queue_space(q) < q->high_mark)) + goto drop_unlock; + + if (ieee80211_is_data_qos(fc)) + priv->stations[sta_id].tid[tid].tfds_in_queue++; /* Set up driver data for this TFD */ memset(&(txq->txb[q->write_ptr]), 0, sizeof(struct iwl_tx_info)); @@ -902,7 +903,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) drop_unlock: spin_unlock_irqrestore(&priv->lock, flags); -drop: return -1; } EXPORT_SYMBOL(iwl_tx_skb); -- cgit v1.2.3 From 45f5fa32b130b2a59f9b726be45ce7fa73fb834c Mon Sep 17 00:00:00 2001 From: reinette chatre Date: Tue, 21 Jul 2009 09:29:07 -0700 Subject: iwlagn: fix minimum number of queues setting We need to provide a reasonable minimum that will result in a working setup if used. Set minimum to be 10 to provide for 4 standard TX queues + 1 command queue + 2 (unused) HCCA queues + 4 HT queues (one per AC). We allow the user to change the number of queues used via a module parameter and use this minimum value to check if it is valid. Without this patch a user can select a value for the number of queues that will result in a failing setup. Signed-off-by: Reinette Chatre Reviewed-by: Tomas Winkler Acked-by: Tomas Winkler Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-3945.h | 2 +- drivers/net/wireless/iwlwifi/iwl-dev.h | 6 ++++-- drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 ++-- 3 files changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index fbb3a573463e..2de6471d4be9 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -112,7 +112,7 @@ enum iwl3945_antenna { #define IWL_TX_FIFO_NONE 7 /* Minimum number of queues. MAX_NUM is defined in hw specific files */ -#define IWL_MIN_NUM_QUEUES 4 +#define IWL39_MIN_NUM_QUEUES 4 #define IEEE80211_DATA_LEN 2304 #define IEEE80211_4ADDR_LEN 30 diff --git a/drivers/net/wireless/iwlwifi/iwl-dev.h b/drivers/net/wireless/iwlwifi/iwl-dev.h index e2d620f0b6e8..650e20af20fa 100644 --- a/drivers/net/wireless/iwlwifi/iwl-dev.h +++ b/drivers/net/wireless/iwlwifi/iwl-dev.h @@ -258,8 +258,10 @@ struct iwl_channel_info { #define IWL_TX_FIFO_HCCA_2 6 #define IWL_TX_FIFO_NONE 7 -/* Minimum number of queues. MAX_NUM is defined in hw specific files */ -#define IWL_MIN_NUM_QUEUES 4 +/* Minimum number of queues. MAX_NUM is defined in hw specific files. + * Set the minimum to accommodate the 4 standard TX queues, 1 command + * queue, 2 (unused) HCCA queues, and 4 HT queues (one for each AC) */ +#define IWL_MIN_NUM_QUEUES 10 /* Power management (not Tx power) structures */ diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 956798f2c80c..2f50ab60bfdf 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -4018,10 +4018,10 @@ static int iwl3945_pci_probe(struct pci_dev *pdev, const struct pci_device_id *e SET_IEEE80211_DEV(hw, &pdev->dev); if ((iwl3945_mod_params.num_of_queues > IWL39_MAX_NUM_QUEUES) || - (iwl3945_mod_params.num_of_queues < IWL_MIN_NUM_QUEUES)) { + (iwl3945_mod_params.num_of_queues < IWL39_MIN_NUM_QUEUES)) { IWL_ERR(priv, "invalid queues_num, should be between %d and %d\n", - IWL_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES); + IWL39_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES); err = -EINVAL; goto out_ieee80211_free_hw; } -- cgit v1.2.3 From 2a21f86917f7a9fe13b180e895a816871a234dee Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sat, 25 Jul 2009 15:22:59 +0300 Subject: wireless: ERR_PTR vs null iwm_wdev_alloc() returns an ERR_PTR on failure and not null. It also prints its own dev_err() message so I removed that as well. Compile tested only. Sorry. Found by smatch (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter Acked-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/netdev.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c index aea5ccf24ccf..bf294e41753b 100644 --- a/drivers/net/wireless/iwmc3200wifi/netdev.c +++ b/drivers/net/wireless/iwmc3200wifi/netdev.c @@ -106,10 +106,8 @@ void *iwm_if_alloc(int sizeof_bus, struct device *dev, int ret = 0; wdev = iwm_wdev_alloc(sizeof_bus, dev); - if (!wdev) { - dev_err(dev, "no memory for wireless device instance\n"); - return ERR_PTR(-ENOMEM); - } + if (IS_ERR(wdev)) + return wdev; iwm = wdev_to_iwm(wdev); iwm->bus_ops = if_ops; -- cgit v1.2.3 From 3d0ccd021b23c18ea2d399fe4a43c955485c765c Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:02:32 +0200 Subject: airo: Buffer overflow SSID_rid has space for only 3 ssids. txPowerLevels[i] is read before the bounds check for i Signed-off-by: Roel Kluin Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/airo.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/airo.c b/drivers/net/wireless/airo.c index c70604f0329e..8ce5e4cee168 100644 --- a/drivers/net/wireless/airo.c +++ b/drivers/net/wireless/airo.c @@ -5918,20 +5918,19 @@ static int airo_set_essid(struct net_device *dev, readSsidRid(local, &SSID_rid); /* Check if we asked for `any' */ - if(dwrq->flags == 0) { + if (dwrq->flags == 0) { /* Just send an empty SSID list */ memset(&SSID_rid, 0, sizeof(SSID_rid)); } else { - int index = (dwrq->flags & IW_ENCODE_INDEX) - 1; + unsigned index = (dwrq->flags & IW_ENCODE_INDEX) - 1; /* Check the size of the string */ - if(dwrq->length > IW_ESSID_MAX_SIZE) { + if (dwrq->length > IW_ESSID_MAX_SIZE) return -E2BIG ; - } + /* Check if index is valid */ - if((index < 0) || (index >= 4)) { + if (index >= ARRAY_SIZE(SSID_rid.ssids)) return -EINVAL; - } /* Set the SSID */ memset(SSID_rid.ssids[index].ssid, 0, @@ -6819,7 +6818,7 @@ static int airo_set_txpow(struct net_device *dev, return -EINVAL; } clear_bit (FLAG_RADIO_OFF, &local->flags); - for (i = 0; cap_rid.txPowerLevels[i] && (i < 8); i++) + for (i = 0; i < 8 && cap_rid.txPowerLevels[i]; i++) if (v == cap_rid.txPowerLevels[i]) { readConfigRid(local, 1); local->config.txPower = v; -- cgit v1.2.3 From 008749fc9917b799c469478141ddd1a4c81d06ca Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:21:22 +0200 Subject: ath9k: Read outside array bounds Incorrect limits leads to reads outside array bounds. Signed-off-by: Roel Kluin Acked-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/eeprom.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/ath9k/eeprom.c b/drivers/net/wireless/ath/ath9k/eeprom.c index a2fda702b620..ce0e86c36a82 100644 --- a/drivers/net/wireless/ath/ath9k/eeprom.c +++ b/drivers/net/wireless/ath/ath9k/eeprom.c @@ -460,7 +460,7 @@ static int ath9k_hw_4k_check_eeprom(struct ath_hw *ah) integer = swab32(eep->modalHeader.antCtrlCommon); eep->modalHeader.antCtrlCommon = integer; - for (i = 0; i < AR5416_MAX_CHAINS; i++) { + for (i = 0; i < AR5416_EEP4K_MAX_CHAINS; i++) { integer = swab32(eep->modalHeader.antCtrlChain[i]); eep->modalHeader.antCtrlChain[i] = integer; } @@ -914,7 +914,7 @@ static void ath9k_hw_set_4k_power_per_rate_table(struct ath_hw *ah, ctlMode, numCtlModes, isHt40CtlMode, (pCtlMode[ctlMode] & EXT_ADDITIVE)); - for (i = 0; (i < AR5416_NUM_CTLS) && + for (i = 0; (i < AR5416_EEP4K_NUM_CTLS) && pEepData->ctlIndex[i]; i++) { DPRINTF(ah->ah_sc, ATH_DBG_EEPROM, " LOOP-Ctlidx %d: cfgCtl 0x%2.2x " -- cgit v1.2.3 From 082e708acc50a5b625b9bde0bb1af90dfdbd1942 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sat, 25 Jul 2009 23:34:31 +0200 Subject: iwlwifi: Read outside array bounds tid is bounded (above) by the size of default_tid_to_tx_fifo (17 elements), but the size of priv->stations[].tid[] is MAX_TID_COUNT (9) elements. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-tx.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index 5febb3186365..2e89040e63be 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -1171,6 +1171,8 @@ int iwl_tx_agg_start(struct iwl_priv *priv, const u8 *ra, u16 tid, u16 *ssn) IWL_ERR(priv, "Start AGG on invalid station\n"); return -ENXIO; } + if (unlikely(tid >= MAX_TID_COUNT)) + return -EINVAL; if (priv->stations[sta_id].tid[tid].agg.state != IWL_AGG_OFF) { IWL_ERR(priv, "Start AGG when state is not IWL_AGG_OFF !\n"); -- cgit v1.2.3 From b68f2fb9e73f46037fbeca5fbd4ae8a7ddd8ef6b Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 27 Jul 2009 10:58:08 +0100 Subject: tty: Fix a USB serial crash/scribble The port lock is used to protect the port state. However the port structure is freed on a hangup, then the lock taken on a close. The right fix is to drop the port on tty->shutdown() but we can't yet do that due to sleep v non-sleeping rules. Instead do the next best thing and fix it up when we are not in -rc season. Reported-by: Daniel Mack Signed-off-by: Alan Cox Tested-by: Daniel Mack Signed-off-by: Linus Torvalds --- drivers/usb/serial/usb-serial.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index bd7581b3a48a..3c8923f62ed1 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -340,6 +340,22 @@ static void serial_close(struct tty_struct *tty, struct file *filp) dbg("%s - port %d", __func__, port->number); + /* FIXME: + This leaves a very narrow race. Really we should do the + serial_do_free() on tty->shutdown(), but tty->shutdown can + be called from IRQ context and serial_do_free can sleep. + + The right fix is probably to make the tty free (which is rare) + and thus tty->shutdown() occur via a work queue and simplify all + the drivers that use it. + */ + if (tty_hung_up_p(filp)) { + /* serial_hangup already called serial_down at this point. + Another user may have already reopened the port but + serial_do_free is refcounted */ + serial_do_free(port); + return; + } if (tty_port_close_start(&port->port, tty, filp) == 0) return; @@ -355,7 +371,8 @@ static void serial_hangup(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; serial_do_down(port); tty_port_hangup(&port->port); - serial_do_free(port); + /* We must not free port yet - the USB serial layer depends on it's + continued existence */ } static int serial_write(struct tty_struct *tty, const unsigned char *buf, -- cgit v1.2.3 From 7cb7f45c7feef43c8f71f5cfedfc0b19be2142f7 Mon Sep 17 00:00:00 2001 From: Len Brown Date: Mon, 27 Jul 2009 18:42:38 -0400 Subject: Revert "ACPICA: Remove obsolete acpi_os_validate_address interface" This reverts commit f9ca058430333c9a24c5ca926aa445125f88df18. which caused a regression: http://bugzilla.kernel.org/show_bug.cgi?id=13620 Signed-off-by: Lin Ming Signed-off-by: Len Brown --- drivers/acpi/acpica/acobject.h | 1 + drivers/acpi/acpica/dsopcode.c | 24 ++++++++++++++++++++++++ drivers/acpi/acpica/exfldio.c | 6 ++++++ include/acpi/acpiosxf.h | 4 ++++ 4 files changed, 35 insertions(+) (limited to 'drivers') diff --git a/drivers/acpi/acpica/acobject.h b/drivers/acpi/acpica/acobject.h index 544dcf834922..eb6f038b03d9 100644 --- a/drivers/acpi/acpica/acobject.h +++ b/drivers/acpi/acpica/acobject.h @@ -97,6 +97,7 @@ #define AOPOBJ_OBJECT_INITIALIZED 0x08 #define AOPOBJ_SETUP_COMPLETE 0x10 #define AOPOBJ_SINGLE_DATUM 0x20 +#define AOPOBJ_INVALID 0x40 /* Used if host OS won't allow an op_region address */ /****************************************************************************** * diff --git a/drivers/acpi/acpica/dsopcode.c b/drivers/acpi/acpica/dsopcode.c index 584d766e6f12..b79978f7bc71 100644 --- a/drivers/acpi/acpica/dsopcode.c +++ b/drivers/acpi/acpica/dsopcode.c @@ -397,6 +397,30 @@ acpi_status acpi_ds_get_region_arguments(union acpi_operand_object *obj_desc) status = acpi_ds_execute_arguments(node, acpi_ns_get_parent_node(node), extra_desc->extra.aml_length, extra_desc->extra.aml_start); + if (ACPI_FAILURE(status)) { + return_ACPI_STATUS(status); + } + + /* Validate the region address/length via the host OS */ + + status = acpi_os_validate_address(obj_desc->region.space_id, + obj_desc->region.address, + (acpi_size) obj_desc->region.length, + acpi_ut_get_node_name(node)); + + if (ACPI_FAILURE(status)) { + /* + * Invalid address/length. We will emit an error message and mark + * the region as invalid, so that it will cause an additional error if + * it is ever used. Then return AE_OK. + */ + ACPI_EXCEPTION((AE_INFO, status, + "During address validation of OpRegion [%4.4s]", + node->name.ascii)); + obj_desc->common.flags |= AOPOBJ_INVALID; + status = AE_OK; + } + return_ACPI_STATUS(status); } diff --git a/drivers/acpi/acpica/exfldio.c b/drivers/acpi/acpica/exfldio.c index d4075b821021..6687be167f5f 100644 --- a/drivers/acpi/acpica/exfldio.c +++ b/drivers/acpi/acpica/exfldio.c @@ -113,6 +113,12 @@ acpi_ex_setup_region(union acpi_operand_object *obj_desc, } } + /* Exit if Address/Length have been disallowed by the host OS */ + + if (rgn_desc->common.flags & AOPOBJ_INVALID) { + return_ACPI_STATUS(AE_AML_ILLEGAL_ADDRESS); + } + /* * Exit now for SMBus address space, it has a non-linear address space * and the request cannot be directly validated diff --git a/include/acpi/acpiosxf.h b/include/acpi/acpiosxf.h index 3e798593b17b..ab0b85cf21f3 100644 --- a/include/acpi/acpiosxf.h +++ b/include/acpi/acpiosxf.h @@ -242,6 +242,10 @@ acpi_os_derive_pci_id(acpi_handle rhandle, acpi_status acpi_os_validate_interface(char *interface); acpi_status acpi_osi_invalidate(char* interface); +acpi_status +acpi_os_validate_address(u8 space_id, acpi_physical_address address, + acpi_size length, char *name); + u64 acpi_os_get_timer(void); acpi_status acpi_os_signal(u32 function, void *info); -- cgit v1.2.3 From 3a54297478e6578f96fd54bf4daa1751130aca86 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Mon, 27 Jul 2009 22:17:51 +0100 Subject: pty: quickfix for the pty ENXIO timing problems This also makes close stall in the normal case which is apparently needed to fix emacs Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/pty.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 6e6942c45f5b..3850a68f265a 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -52,6 +52,7 @@ static void pty_close(struct tty_struct *tty, struct file *filp) return; tty->link->packet = 0; set_bit(TTY_OTHER_CLOSED, &tty->link->flags); + tty_flip_buffer_push(tty->link); wake_up_interruptible(&tty->link->read_wait); wake_up_interruptible(&tty->link->write_wait); if (tty->driver->subtype == PTY_TYPE_MASTER) { @@ -207,6 +208,7 @@ static int pty_open(struct tty_struct *tty, struct file *filp) clear_bit(TTY_OTHER_CLOSED, &tty->link->flags); set_bit(TTY_THROTTLED, &tty->flags); retval = 0; + tty->low_latency = 1; out: return retval; } -- cgit v1.2.3 From c56d300086140c93dc3390e5300fd17df802ec0e Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Tue, 28 Jul 2009 00:34:58 +0100 Subject: usb_serial: Fix remaining ref count/lock bugs This fixes - locking bug that was hidden by ecc2e05e739c30870c8e4f252b63a0c4041f2724 - Regression #13821 - Spurious warning when closing and blocking for data write out With these changes my PL2303 always ends up as ttyUSB0 when it should and the module refcounts stay correct. I'll do a more wholesale split & tidy of _open in the next release or two as we get a standard tty_port_open and port->ops->init port->ops->shutdown call backs. Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the reports but it passes local testing with the same hardware as Alan Stern. Signed-off-by: Alan Cox Signed-off-by: Linus Torvalds --- drivers/usb/serial/usb-serial.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 3c8923f62ed1..99188c92068b 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -32,6 +32,7 @@ #include #include #include +#include #include #include #include "pl2303.h" @@ -184,6 +185,7 @@ static int serial_open (struct tty_struct *tty, struct file *filp) struct usb_serial_port *port; unsigned int portNumber; int retval = 0; + int first = 0; dbg("%s", __func__); @@ -223,7 +225,7 @@ static int serial_open (struct tty_struct *tty, struct file *filp) /* If the console is attached, the device is already open */ if (port->port.count == 1 && !port->console) { - + first = 1; /* lock this module before we call it * this may fail, which means we must bail out, * safe because we are called with BKL held */ @@ -246,13 +248,21 @@ static int serial_open (struct tty_struct *tty, struct file *filp) if (retval) goto bailout_interface_put; mutex_unlock(&serial->disc_mutex); + set_bit(ASYNCB_INITIALIZED, &port->port.flags); } mutex_unlock(&port->mutex); /* Now do the correct tty layer semantics */ retval = tty_port_block_til_ready(&port->port, tty, filp); - if (retval == 0) + if (retval == 0) { + if (!first) + usb_serial_put(serial); return 0; - + } + mutex_lock(&port->mutex); + if (first == 0) + goto bailout_mutex_unlock; + /* Undo the initial port actions */ + mutex_lock(&serial->disc_mutex); bailout_interface_put: usb_autopm_put_interface(serial->interface); bailout_module_put: @@ -411,7 +421,6 @@ static int serial_chars_in_buffer(struct tty_struct *tty) struct usb_serial_port *port = tty->driver_data; dbg("%s = port %d", __func__, port->number); - WARN_ON(!port->port.count); /* if the device was unplugged then any remaining characters fell out of the connector ;) */ if (port->serial->disconnected) -- cgit v1.2.3 From 48f5690d45b79ffeedc5ab24243b576056f1d2ff Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:52:06 +0200 Subject: mg_disk: remove prohibited sleep operation mflash's polling driver operate in standard request_fn_proc's context, sleep in this isn't permitted. Signed-off-by: unsik Kim Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index f703f5478246..5b120eab2baa 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -245,8 +245,6 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec) mg_dump_status("not ready", status, host); return MG_ERR_INV_STAT; } - if (prv_data->use_polling) - msleep(1); status = inb((unsigned long)host->dev_base + MG_REG_STATUS); } while (time_before(cur_jiffies, expire)); -- cgit v1.2.3 From eb32baec15c38ae6f06cb898a9f791578c5f8c79 Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:52:07 +0200 Subject: mg_disk: fix reading invalid status when use polling driver When using polling driver, little delay is required to access status register. Without this, host might read invalid status. Signed-off-by: unsik Kim Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'drivers') diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 5b120eab2baa..6440d5945414 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -219,6 +219,16 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec) host->error = MG_ERR_NONE; expire = jiffies + msecs_to_jiffies(msec); + /* These 2 times dummy status read prevents reading invalid + * status. A very little time (3 times of mflash operating clk) + * is required for busy bit is set. Use dummy read instead of + * busy wait, because mflash's PLL is machine dependent. + */ + if (prv_data->use_polling) { + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); + } + status = inb((unsigned long)host->dev_base + MG_REG_STATUS); do { -- cgit v1.2.3 From 394c6cc63c1d6900ad7498a3221a1d48fc00c4fa Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Tue, 28 Jul 2009 08:56:34 +0200 Subject: mg_disk: fix issue with data integrity on error in mg_write() We cannot acknowledge the sector write before checking its status (which is done on the next loop iteration) and we also need to do the final status register check after writing the last sector. Fix mg_write() to match mg_write_intr() in this regard. While at it: - add mg_read_one() and mg_write_one() helpers - always use MG_SECTOR_SIZE and remove MG_STORAGE_BUFFER_SIZE [bart: thanks to Tejun for porting the patch over recent block changes] Cc: unsik Kim Cc: Tejun Heo Signed-off-by: Bartlomiej Zolnierkiewicz =================================================================== Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 89 ++++++++++++++++++++++++++----------------------- 1 file changed, 47 insertions(+), 42 deletions(-) (limited to 'drivers') diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 6440d5945414..19917d5481bd 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -36,7 +36,6 @@ /* Register offsets */ #define MG_BUFF_OFFSET 0x8000 -#define MG_STORAGE_BUFFER_SIZE 0x200 #define MG_REG_OFFSET 0xC000 #define MG_REG_FEATURE (MG_REG_OFFSET + 2) /* write case */ #define MG_REG_ERROR (MG_REG_OFFSET + 2) /* read case */ @@ -477,9 +476,18 @@ static unsigned int mg_out(struct mg_host *host, return MG_ERR_NONE; } +static void mg_read_one(struct mg_host *host, struct request *req) +{ + u16 *buff = (u16 *)req->buffer; + u32 i; + + for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) + *buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET + + (i << 1)); +} + static void mg_read(struct request *req) { - u32 j; struct mg_host *host = req->rq_disk->private_data; if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), @@ -490,26 +498,33 @@ static void mg_read(struct request *req) blk_rq_sectors(req), blk_rq_pos(req), req->buffer); do { - u16 *buff = (u16 *)req->buffer; - if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_RD_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - for (j = 0; j < MG_SECTOR_SIZE >> 1; j++) - *buff++ = inw((unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); + + mg_read_one(host, req); outb(MG_CMD_RD_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); } +static void mg_write_one(struct mg_host *host, struct request *req) +{ + u16 *buff = (u16 *)req->buffer; + u32 i; + + for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) + outw(*buff++, (unsigned long)host->dev_base + MG_BUFF_OFFSET + + (i << 1)); +} + static void mg_write(struct request *req) { - u32 j; struct mg_host *host = req->rq_disk->private_data; + bool rem; if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), MG_CMD_WR, NULL) != MG_ERR_NONE) { @@ -520,27 +535,37 @@ static void mg_write(struct request *req) MG_DBG("requested %d sects (from %ld), buffer=0x%p\n", blk_rq_sectors(req), blk_rq_pos(req), req->buffer); - do { - u16 *buff = (u16 *)req->buffer; + if (mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + mg_bad_rw_intr(host); + return; + } + + mg_write_one(host, req); + + outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); - if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + do { + if (blk_rq_sectors(req) > 1 && + mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - for (j = 0; j < MG_SECTOR_SIZE >> 1; j++) - outw(*buff++, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); - outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + - MG_REG_COMMAND); - } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); + rem = mg_end_request(host, 0, MG_SECTOR_SIZE); + if (rem) + mg_write_one(host, req); + + outb(MG_CMD_WR_CONF, + (unsigned long)host->dev_base + MG_REG_COMMAND); + } while (rem); } static void mg_read_intr(struct mg_host *host) { struct request *req = host->req; u32 i; - u16 *buff; /* check status */ do { @@ -558,13 +583,7 @@ static void mg_read_intr(struct mg_host *host) return; ok_to_read: - /* get current segment of request */ - buff = (u16 *)req->buffer; - - /* read 1 sector */ - for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) - *buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET + - (i << 1)); + mg_read_one(host, req); MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n", blk_rq_pos(req), blk_rq_sectors(req) - 1, req->buffer); @@ -583,8 +602,7 @@ ok_to_read: static void mg_write_intr(struct mg_host *host) { struct request *req = host->req; - u32 i, j; - u16 *buff; + u32 i; bool rem; /* check status */ @@ -605,12 +623,7 @@ static void mg_write_intr(struct mg_host *host) ok_to_write: if ((rem = mg_end_request(host, 0, MG_SECTOR_SIZE))) { /* write 1 sector and set handler if remains */ - buff = (u16 *)req->buffer; - for (j = 0; j < MG_STORAGE_BUFFER_SIZE >> 1; j++) { - outw(*buff, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (j << 1)); - buff++; - } + mg_write_one(host, req); MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n", blk_rq_pos(req), blk_rq_sectors(req), req->buffer); host->mg_do_intr = mg_write_intr; @@ -675,9 +688,6 @@ static unsigned int mg_issue_req(struct request *req, unsigned int sect_num, unsigned int sect_cnt) { - u16 *buff; - u32 i; - switch (rq_data_dir(req)) { case READ: if (mg_out(host, sect_num, sect_cnt, MG_CMD_RD, &mg_read_intr) @@ -701,12 +711,7 @@ static unsigned int mg_issue_req(struct request *req, mg_bad_rw_intr(host); return host->error; } - buff = (u16 *)req->buffer; - for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) { - outw(*buff, (unsigned long)host->dev_base + - MG_BUFF_OFFSET + (i << 1)); - buff++; - } + mg_write_one(host, req); mod_timer(&host->timer, jiffies + 3 * HZ); outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); -- cgit v1.2.3 From a85a00a699740f6f9863f88aef22060fe1534681 Mon Sep 17 00:00:00 2001 From: unsik Kim Date: Tue, 28 Jul 2009 08:57:33 +0200 Subject: mg_disk: Add missing ready status check on mg_write() When last sector is written, ready bit of status register should be checked. Signed-off-by: unsik Kim Acked-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jens Axboe --- drivers/block/mg_disk.c | 32 +++++++++++++++----------------- 1 file changed, 15 insertions(+), 17 deletions(-) (limited to 'drivers') diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c index 19917d5481bd..6d7fbaa92248 100644 --- a/drivers/block/mg_disk.c +++ b/drivers/block/mg_disk.c @@ -524,16 +524,16 @@ static void mg_write_one(struct mg_host *host, struct request *req) static void mg_write(struct request *req) { struct mg_host *host = req->rq_disk->private_data; - bool rem; + unsigned int rem = blk_rq_sectors(req); - if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req), + if (mg_out(host, blk_rq_pos(req), rem, MG_CMD_WR, NULL) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } MG_DBG("requested %d sects (from %ld), buffer=0x%p\n", - blk_rq_sectors(req), blk_rq_pos(req), req->buffer); + rem, blk_rq_pos(req), req->buffer); if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { @@ -541,25 +541,23 @@ static void mg_write(struct request *req) return; } - mg_write_one(host, req); + do { + mg_write_one(host, req); - outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND); + outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + + MG_REG_COMMAND); - do { - if (blk_rq_sectors(req) > 1 && - mg_wait(host, ATA_DRQ, - MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + rem--; + if (rem > 1 && mg_wait(host, ATA_DRQ, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { + mg_bad_rw_intr(host); + return; + } else if (mg_wait(host, MG_STAT_READY, + MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) { mg_bad_rw_intr(host); return; } - - rem = mg_end_request(host, 0, MG_SECTOR_SIZE); - if (rem) - mg_write_one(host, req); - - outb(MG_CMD_WR_CONF, - (unsigned long)host->dev_base + MG_REG_COMMAND); - } while (rem); + } while (mg_end_request(host, 0, MG_SECTOR_SIZE)); } static void mg_read_intr(struct mg_host *host) -- cgit v1.2.3 From 1b54ab450b180eaeeb0eee6f0f64349246a22c14 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Tue, 28 Jul 2009 16:31:39 +0200 Subject: hwmon: (smsc47m1) Differentiate between LPC47M233 and LPC47M292 The SMSC LPC47M233 and LPC47M292 chips have the same device ID but are not compatible. Signed-off-by: Jean Delvare Cc: Juerg Haefliger Acked-by: Hans de Goede --- drivers/hwmon/smsc47m1.c | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'drivers') diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c index a92dbb97ee99..ba75bfcf14ce 100644 --- a/drivers/hwmon/smsc47m1.c +++ b/drivers/hwmon/smsc47m1.c @@ -86,6 +86,7 @@ superio_exit(void) #define SUPERIO_REG_ACT 0x30 #define SUPERIO_REG_BASE 0x60 #define SUPERIO_REG_DEVID 0x20 +#define SUPERIO_REG_DEVREV 0x21 /* Logical device registers */ @@ -429,6 +430,9 @@ static int __init smsc47m1_find(unsigned short *addr, * The LPC47M292 (device id 0x6B) is somewhat compatible, but it * supports a 3rd fan, and the pin configuration registers are * unfortunately different. + * The LPC47M233 has the same device id (0x6B) but is not compatible. + * We check the high bit of the device revision register to + * differentiate them. */ switch (val) { case 0x51: @@ -448,6 +452,13 @@ static int __init smsc47m1_find(unsigned short *addr, sio_data->type = smsc47m1; break; case 0x6B: + if (superio_inb(SUPERIO_REG_DEVREV) & 0x80) { + pr_debug(DRVNAME ": " + "Found SMSC LPC47M233, unsupported\n"); + superio_exit(); + return -ENODEV; + } + pr_info(DRVNAME ": Found SMSC LPC47M292\n"); sio_data->type = smsc47m2; break; -- cgit v1.2.3 From 8d282497cbf8124d6814d51a74fb13d69531c669 Mon Sep 17 00:00:00 2001 From: Luca Tettamanti Date: Tue, 28 Jul 2009 16:31:39 +0200 Subject: hwmon: (asus_atk0110) Fix upper limit readings On newer Asus boards the "upper" limit of a sensor is encoded as delta from the "lower" limit. Fix the driver to correctly handle this case. Signed-off-by: Luca Tettamanti Tested-by: Alex Macfarlane Smith Signed-off-by: Jean Delvare --- drivers/hwmon/asus_atk0110.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/hwmon/asus_atk0110.c b/drivers/hwmon/asus_atk0110.c index bff0103610c1..fe4fa29c9219 100644 --- a/drivers/hwmon/asus_atk0110.c +++ b/drivers/hwmon/asus_atk0110.c @@ -593,7 +593,11 @@ static int atk_add_sensor(struct atk_data *data, union acpi_object *obj) sensor->data = data; sensor->id = flags->integer.value; sensor->limit1 = limit1->integer.value; - sensor->limit2 = limit2->integer.value; + if (data->old_interface) + sensor->limit2 = limit2->integer.value; + else + /* The upper limit is expressed as delta from lower limit */ + sensor->limit2 = sensor->limit1 + limit2->integer.value; snprintf(sensor->input_attr_name, ATTR_NAME_SIZE, "%s%d_input", base_name, start + *num); -- cgit v1.2.3 From 96f699ad09c8b3c55cd229506a9add0047838e3e Mon Sep 17 00:00:00 2001 From: Michele Jr De Candia Date: Tue, 28 Jul 2009 16:33:03 +0200 Subject: i2c/tsl2550: Fix lux value in dark environment I've tested TSL2550 driver and I've found a bug: when light is off, returned value from tsl2550_calculate_lux function is -1 when it should be 0 (sensor correctly read that light was off). I think the bug is that a zero c0 value (approximated value of ch0) is misinterpreted as an error. Signed-off-by: Michele Jr De Candia Acked-by: Rodolfo Giometti Signed-off-by: Jean Delvare --- drivers/i2c/chips/tsl2550.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/i2c/chips/tsl2550.c b/drivers/i2c/chips/tsl2550.c index 1a9cc135219f..b96f3025e588 100644 --- a/drivers/i2c/chips/tsl2550.c +++ b/drivers/i2c/chips/tsl2550.c @@ -27,7 +27,7 @@ #include #define TSL2550_DRV_NAME "tsl2550" -#define DRIVER_VERSION "1.1.1" +#define DRIVER_VERSION "1.1.2" /* * Defines @@ -189,13 +189,16 @@ static int tsl2550_calculate_lux(u8 ch0, u8 ch1) u8 r = 128; /* Avoid division by 0 and count 1 cannot be greater than count 0 */ - if (c0 && (c1 <= c0)) - r = c1 * 128 / c0; + if (c1 <= c0) + if (c0) { + r = c1 * 128 / c0; + + /* Calculate LUX */ + lux = ((c0 - c1) * ratio_lut[r]) / 256; + } else + lux = 0; else - return -1; - - /* Calculate LUX */ - lux = ((c0 - c1) * ratio_lut[r]) / 256; + return -EAGAIN; /* LUX range check */ return lux > TSL2550_MAX_LUX ? TSL2550_MAX_LUX : lux; -- cgit v1.2.3 From 3b4418c67a70278964b063b5e1f56dcb3d0a41f3 Mon Sep 17 00:00:00 2001 From: Ming Lei Date: Sat, 11 Jul 2009 11:11:10 +0800 Subject: driver core: firmware_class:fix memory leak of page pointers array The page pointers array is allocated in fw_realloc_buffer() called by firmware_data_write(), and should be freed in release function of firmware device. Signed-off-by: Ming Lei Reported-by: Catalin Marinas Acked-by: David Woodhouse Signed-off-by: Greg Kroah-Hartman --- drivers/base/firmware_class.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/base/firmware_class.c b/drivers/base/firmware_class.c index f285f441fab9..7376367bcb80 100644 --- a/drivers/base/firmware_class.c +++ b/drivers/base/firmware_class.c @@ -180,7 +180,6 @@ static ssize_t firmware_loading_store(struct device *dev, goto err; } /* Pages will be freed by vfree() */ - fw_priv->pages = NULL; fw_priv->page_array_size = 0; fw_priv->nr_pages = 0; complete(&fw_priv->completion); -- cgit v1.2.3 From 79f0313bfc67aa13abb931e8c12a1411f0161a68 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Fri, 24 Jul 2009 17:31:41 +0800 Subject: driver core: sysdev: do not send KOBJ_ADD uevent if kobject_init_and_add fails If kobject_init_and_add fails, sysdev_register should not send KOBJ_ADD uevent to userspace. Signed-off-by: Xiaotian Feng Signed-off-by: Greg Kroah-Hartman --- drivers/base/sys.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/base/sys.c b/drivers/base/sys.c index 79a9ae5238ac..0d903909af7e 100644 --- a/drivers/base/sys.c +++ b/drivers/base/sys.c @@ -275,9 +275,9 @@ int sysdev_register(struct sys_device *sysdev) drv->add(sysdev); } mutex_unlock(&sysdev_drivers_lock); + kobject_uevent(&sysdev->kobj, KOBJ_ADD); } - kobject_uevent(&sysdev->kobj, KOBJ_ADD); return error; } -- cgit v1.2.3 From f3a756883ac028c536479e2eb283477fec80c828 Mon Sep 17 00:00:00 2001 From: Bill Pemberton Date: Tue, 14 Jul 2009 15:33:52 -0400 Subject: Staging: serqt_usb2: add missing calls to tty_kref_put() tty_port_tty_get() was called without a corresponding tty_kref_put() in qt_read_bulk_callback() and qt_close(). Signed-off-by: Bill Pemberton Signed-off-by: Greg Kroah-Hartman --- drivers/staging/serqt_usb2/serqt_usb2.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c index a9bd4106beb7..f9ff9c266780 100644 --- a/drivers/staging/serqt_usb2/serqt_usb2.c +++ b/drivers/staging/serqt_usb2/serqt_usb2.c @@ -360,18 +360,18 @@ static void qt_read_bulk_callback(struct urb *urb) if (port_paranoia_check(port, __func__) != 0) { dbg("%s - port_paranoia_check, exiting\n", __func__); qt_port->ReadBulkStopped = 1; - return; + goto exit; } if (!serial) { dbg("%s - bad serial pointer, exiting\n", __func__); - return; + goto exit; } if (qt_port->closePending == 1) { /* Were closing , stop reading */ dbg("%s - (qt_port->closepending == 1\n", __func__); qt_port->ReadBulkStopped = 1; - return; + goto exit; } /* @@ -381,7 +381,7 @@ static void qt_read_bulk_callback(struct urb *urb) */ if (qt_port->RxHolding == 1) { qt_port->ReadBulkStopped = 1; - return; + goto exit; } if (urb->status) { @@ -389,7 +389,7 @@ static void qt_read_bulk_callback(struct urb *urb) dbg("%s - nonzero read bulk status received: %d\n", __func__, urb->status); - return; + goto exit; } if (tty && RxCount) { @@ -463,6 +463,8 @@ static void qt_read_bulk_callback(struct urb *urb) } schedule_work(&port->work); +exit: + tty_kref_put(tty); } /* @@ -1041,7 +1043,7 @@ static void qt_block_until_empty(struct tty_struct *tty, } } -static void qt_close( struct usb_serial_port *port) +static void qt_close(struct usb_serial_port *port) { struct usb_serial *serial = port->serial; struct quatech_port *qt_port; @@ -1068,6 +1070,7 @@ static void qt_close( struct usb_serial_port *port) /* wait up to for transmitter to empty */ if (serial->dev) qt_block_until_empty(tty, qt_port); + tty_kref_put(tty); /* Close uart channel */ status = qt_close_channel(serial, index); -- cgit v1.2.3 From de8f8bd63334fe2014be7d9ab3a81ce9b96e5d19 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 13 Jul 2009 10:46:57 +0200 Subject: Staging: serqt_usb2: fix memory leak in error case a standard memory leak, as later allocations may fail even if prior allocations did not. Then the prior allocations must be undone. Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/staging/serqt_usb2/serqt_usb2.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c index f9ff9c266780..0fdf8c6dc648 100644 --- a/drivers/staging/serqt_usb2/serqt_usb2.c +++ b/drivers/staging/serqt_usb2/serqt_usb2.c @@ -738,6 +738,11 @@ static int qt_startup(struct usb_serial *serial) if (!qt_port) { dbg("%s: kmalloc for quatech_port (%d) failed!.", __func__, i); + for(--i; i >= 0; i--) { + port = serial->port[i]; + kfree(usb_get_serial_port_data(port)); + usb_set_serial_port_data(port, NULL); + } return -ENOMEM; } spin_lock_init(&qt_port->lock); -- cgit v1.2.3 From a6a9f81ccc9f5c86ccc22bbed1960a57d0316e8b Mon Sep 17 00:00:00 2001 From: David Rientjes Date: Tue, 16 Jun 2009 16:42:53 -0700 Subject: Staging: android: lowmemorykiller.c: fix it for "oom: move oom_adj value from task_struct to mm_struct" I'm about to merge "oom: move oom_adj value from task_struct to mm_struct", and this fixup is needed to repair linux-next's drivers/staging/android/lowmemorykiller.c. Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/staging/android/lowmemorykiller.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/staging/android/lowmemorykiller.c b/drivers/staging/android/lowmemorykiller.c index fe72240f5a9e..f934393f3959 100644 --- a/drivers/staging/android/lowmemorykiller.c +++ b/drivers/staging/android/lowmemorykiller.c @@ -96,19 +96,21 @@ static int lowmem_shrink(int nr_to_scan, gfp_t gfp_mask) read_lock(&tasklist_lock); for_each_process(p) { + struct mm_struct *mm; int oom_adj; task_lock(p); - if (!p->mm) { + mm = p->mm; + if (!mm) { task_unlock(p); continue; } - oom_adj = p->oomkilladj; + oom_adj = mm->oom_adj; if (oom_adj < min_adj) { task_unlock(p); continue; } - tasksize = get_mm_rss(p->mm); + tasksize = get_mm_rss(mm); task_unlock(p); if (tasksize <= 0) continue; -- cgit v1.2.3 From 0bfc240575acb8769d0be78facedabd8e3d2c33a Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Sun, 19 Jul 2009 23:37:32 -0700 Subject: staging: remove aten2011 driver This driver is not needed, as the existing mos7840 driver works properly for this device. Thanks to Russell Lang for doing the work to figure this out. Cc: Russell Lang Signed-off-by: Greg Kroah-Hartman --- drivers/staging/Kconfig | 2 - drivers/staging/Makefile | 1 - drivers/staging/uc2322/Kconfig | 10 - drivers/staging/uc2322/Makefile | 1 - drivers/staging/uc2322/TODO | 7 - drivers/staging/uc2322/aten2011.c | 2430 ------------------------------------- 6 files changed, 2451 deletions(-) delete mode 100644 drivers/staging/uc2322/Kconfig delete mode 100644 drivers/staging/uc2322/Makefile delete mode 100644 drivers/staging/uc2322/TODO delete mode 100644 drivers/staging/uc2322/aten2011.c (limited to 'drivers') diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index 348bf61a8fec..975ecddbce30 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -103,8 +103,6 @@ source "drivers/staging/pohmelfs/Kconfig" source "drivers/staging/stlc45xx/Kconfig" -source "drivers/staging/uc2322/Kconfig" - source "drivers/staging/b3dfg/Kconfig" source "drivers/staging/phison/Kconfig" diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile index 8d61d7b4debf..2241ae1b21ee 100644 --- a/drivers/staging/Makefile +++ b/drivers/staging/Makefile @@ -34,7 +34,6 @@ obj-$(CONFIG_ANDROID) += android/ obj-$(CONFIG_DST) += dst/ obj-$(CONFIG_POHMELFS) += pohmelfs/ obj-$(CONFIG_STLC45XX) += stlc45xx/ -obj-$(CONFIG_USB_SERIAL_ATEN2011) += uc2322/ obj-$(CONFIG_B3DFG) += b3dfg/ obj-$(CONFIG_IDE_PHISON) += phison/ obj-$(CONFIG_PLAN9AUTH) += p9auth/ diff --git a/drivers/staging/uc2322/Kconfig b/drivers/staging/uc2322/Kconfig deleted file mode 100644 index 2e0c6e79df2b..000000000000 --- a/drivers/staging/uc2322/Kconfig +++ /dev/null @@ -1,10 +0,0 @@ -config USB_SERIAL_ATEN2011 - tristate "ATEN 2011 USB to serial device support" - depends on USB_SERIAL - default N - ---help--- - Say Y here if you want to use a ATEN 2011 dual port USB to serial - adapter. - - To compile this driver as a module, choose M here: the module will be - called aten2011. diff --git a/drivers/staging/uc2322/Makefile b/drivers/staging/uc2322/Makefile deleted file mode 100644 index 49c18d6e579f..000000000000 --- a/drivers/staging/uc2322/Makefile +++ /dev/null @@ -1 +0,0 @@ -obj-$(CONFIG_USB_SERIAL_ATEN2011) += aten2011.o diff --git a/drivers/staging/uc2322/TODO b/drivers/staging/uc2322/TODO deleted file mode 100644 index c189a64c4185..000000000000 --- a/drivers/staging/uc2322/TODO +++ /dev/null @@ -1,7 +0,0 @@ -TODO: - - checkpatch.pl cleanups - - remove dead and useless code (auditing the tty ioctls to - verify that they really are correct and needed.) - -Please send any patches to Greg Kroah-Hartman and -Russell Lang . diff --git a/drivers/staging/uc2322/aten2011.c b/drivers/staging/uc2322/aten2011.c deleted file mode 100644 index 39d0926d1a90..000000000000 --- a/drivers/staging/uc2322/aten2011.c +++ /dev/null @@ -1,2430 +0,0 @@ -/* - * Aten 2011 USB serial driver for 4 port devices - * - * Copyright (C) 2000 Inside Out Networks - * Copyright (C) 2001-2002, 2009 Greg Kroah-Hartman - * Copyright (C) 2009 Novell Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - - -#define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */ -#define ZLP_REG2 0x3B /* Zero_Flag_Reg2 59 */ -#define ZLP_REG3 0x3C /* Zero_Flag_Reg3 60 */ -#define ZLP_REG4 0x3D /* Zero_Flag_Reg4 61 */ -#define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */ - -/* Interrupt Rotinue Defines */ -#define SERIAL_IIR_RLS 0x06 -#define SERIAL_IIR_RDA 0x04 -#define SERIAL_IIR_CTI 0x0c -#define SERIAL_IIR_THR 0x02 -#define SERIAL_IIR_MS 0x00 - -/* Emulation of the bit mask on the LINE STATUS REGISTER. */ -#define SERIAL_LSR_DR 0x0001 -#define SERIAL_LSR_OE 0x0002 -#define SERIAL_LSR_PE 0x0004 -#define SERIAL_LSR_FE 0x0008 -#define SERIAL_LSR_BI 0x0010 -#define SERIAL_LSR_THRE 0x0020 -#define SERIAL_LSR_TEMT 0x0040 -#define SERIAL_LSR_FIFOERR 0x0080 - -/* MSR bit defines(place holders) */ -#define ATEN_MSR_DELTA_CTS 0x10 -#define ATEN_MSR_DELTA_DSR 0x20 -#define ATEN_MSR_DELTA_RI 0x40 -#define ATEN_MSR_DELTA_CD 0x80 - -/* Serial Port register Address */ -#define RECEIVE_BUFFER_REGISTER ((__u16)(0x00)) -#define TRANSMIT_HOLDING_REGISTER ((__u16)(0x00)) -#define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01)) -#define INTERRUPT_IDENT_REGISTER ((__u16)(0x02)) -#define FIFO_CONTROL_REGISTER ((__u16)(0x02)) -#define LINE_CONTROL_REGISTER ((__u16)(0x03)) -#define MODEM_CONTROL_REGISTER ((__u16)(0x04)) -#define LINE_STATUS_REGISTER ((__u16)(0x05)) -#define MODEM_STATUS_REGISTER ((__u16)(0x06)) -#define SCRATCH_PAD_REGISTER ((__u16)(0x07)) -#define DIVISOR_LATCH_LSB ((__u16)(0x00)) -#define DIVISOR_LATCH_MSB ((__u16)(0x01)) - -#define SP1_REGISTER ((__u16)(0x00)) -#define CONTROL1_REGISTER ((__u16)(0x01)) -#define CLK_MULTI_REGISTER ((__u16)(0x02)) -#define CLK_START_VALUE_REGISTER ((__u16)(0x03)) -#define DCR1_REGISTER ((__u16)(0x04)) -#define GPIO_REGISTER ((__u16)(0x07)) - -#define SERIAL_LCR_DLAB ((__u16)(0x0080)) - -/* - * URB POOL related defines - */ -#define NUM_URBS 16 /* URB Count */ -#define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */ - -#define USB_VENDOR_ID_ATENINTL 0x0557 -#define ATENINTL_DEVICE_ID_2011 0x2011 -#define ATENINTL_DEVICE_ID_7820 0x7820 - -static struct usb_device_id id_table[] = { - { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_2011) }, - { USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_7820) }, - { } /* terminating entry */ -}; -MODULE_DEVICE_TABLE(usb, id_table); - -/* This structure holds all of the local port information */ -struct ATENINTL_port { - int port_num; /*Actual port number in the device(1,2,etc)*/ - __u8 bulk_out_endpoint; /* the bulk out endpoint handle */ - unsigned char *bulk_out_buffer; /* buffer used for the bulk out endpoint */ - struct urb *write_urb; /* write URB for this port */ - __u8 bulk_in_endpoint; /* the bulk in endpoint handle */ - unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */ - struct urb *read_urb; /* read URB for this port */ - __u8 shadowLCR; /* last LCR value received */ - __u8 shadowMCR; /* last MCR value received */ - char open; - char chaseResponsePending; - wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */ - wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */ - struct async_icount icount; - struct usb_serial_port *port; /* loop back to the owner of this object */ - /*Offsets*/ - __u8 SpRegOffset; - __u8 ControlRegOffset; - __u8 DcrRegOffset; - /* for processing control URBS in interrupt context */ - struct urb *control_urb; - char *ctrl_buf; - int MsrLsr; - - struct urb *write_urb_pool[NUM_URBS]; - /* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */ - struct ktermios tmp_termios; /* stores the old termios settings */ - spinlock_t lock; /* private lock */ -}; - -/* This structure holds all of the individual serial device information */ -struct ATENINTL_serial { - __u8 interrupt_in_endpoint; /* the interrupt endpoint handle */ - unsigned char *interrupt_in_buffer; /* the buffer we use for the interrupt endpoint */ - struct urb *interrupt_read_urb; /* our interrupt urb */ - __u8 bulk_in_endpoint; /* the bulk in endpoint handle */ - unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */ - struct urb *read_urb; /* our bulk read urb */ - __u8 bulk_out_endpoint; /* the bulk out endpoint handle */ - struct usb_serial *serial; /* loop back to the owner of this object */ - int ATEN2011_spectrum_2or4ports; /* this says the number of ports in the device */ - /* Indicates about the no.of opened ports of an individual USB-serial adapater. */ - unsigned int NoOfOpenPorts; - /* a flag for Status endpoint polling */ - unsigned char status_polling_started; -}; - -static void ATEN2011_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old_termios); -static void ATEN2011_change_port_settings(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - struct ktermios *old_termios); - -/************************************* - * Bit definitions for each register * - *************************************/ -#define LCR_BITS_5 0x00 /* 5 bits/char */ -#define LCR_BITS_6 0x01 /* 6 bits/char */ -#define LCR_BITS_7 0x02 /* 7 bits/char */ -#define LCR_BITS_8 0x03 /* 8 bits/char */ -#define LCR_BITS_MASK 0x03 /* Mask for bits/char field */ - -#define LCR_STOP_1 0x00 /* 1 stop bit */ -#define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */ -#define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */ -#define LCR_STOP_MASK 0x04 /* Mask for stop bits field */ - -#define LCR_PAR_NONE 0x00 /* No parity */ -#define LCR_PAR_ODD 0x08 /* Odd parity */ -#define LCR_PAR_EVEN 0x18 /* Even parity */ -#define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */ -#define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */ -#define LCR_PAR_MASK 0x38 /* Mask for parity field */ - -#define LCR_SET_BREAK 0x40 /* Set Break condition */ -#define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */ - -#define MCR_DTR 0x01 /* Assert DTR */ -#define MCR_RTS 0x02 /* Assert RTS */ -#define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */ -#define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */ -#define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */ -#define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */ - -#define ATEN2011_MSR_CTS 0x10 /* Current state of CTS */ -#define ATEN2011_MSR_DSR 0x20 /* Current state of DSR */ -#define ATEN2011_MSR_RI 0x40 /* Current state of RI */ -#define ATEN2011_MSR_CD 0x80 /* Current state of CD */ - - -static int debug; - -/* - * Version Information - */ -#define DRIVER_VERSION "2.0" -#define DRIVER_DESC "ATENINTL 2011 USB Serial Adapter" - -/* - * Defines used for sending commands to port - */ - -#define ATEN_WDR_TIMEOUT (50) /* default urb timeout */ - -/* Requests */ -#define ATEN_RD_RTYPE 0xC0 -#define ATEN_WR_RTYPE 0x40 -#define ATEN_RDREQ 0x0D -#define ATEN_WRREQ 0x0E -#define ATEN_CTRL_TIMEOUT 500 -#define VENDOR_READ_LENGTH (0x01) - -/* set to 1 for RS485 mode and 0 for RS232 mode */ -/* FIXME make this somehow dynamic and not build time specific */ -static int RS485mode; - -static int set_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 val) -{ - struct usb_device *dev = port->serial->dev; - val = val & 0x00ff; - - dbg("%s: is %x, value %x", __func__, reg, val); - - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ, - ATEN_WR_RTYPE, val, reg, NULL, 0, - ATEN_WDR_TIMEOUT); -} - -static int get_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 *val) -{ - struct usb_device *dev = port->serial->dev; - int ret; - - ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ, - ATEN_RD_RTYPE, 0, reg, val, VENDOR_READ_LENGTH, - ATEN_WDR_TIMEOUT); - dbg("%s: offset is %x, return val %x", __func__, reg, *val); - *val = (*val) & 0x00ff; - return ret; -} - -static int set_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 val) -{ - struct usb_device *dev = port->serial->dev; - struct ATENINTL_serial *a_serial; - __u16 minor; - - a_serial = usb_get_serial_data(port->serial); - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - val = val & 0x00ff; - - /* - * For the UART control registers, - * the application number need to be Or'ed - */ - if (a_serial->ATEN2011_spectrum_2or4ports == 4) - val |= (((__u16)port->number - minor) + 1) << 8; - else { - if (((__u16) port->number - minor) == 0) - val |= (((__u16)port->number - minor) + 1) << 8; - else - val |= (((__u16)port->number - minor) + 2) << 8; - } - dbg("%s: application number is %x", __func__, val); - - return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ, - ATEN_WR_RTYPE, val, reg, NULL, 0, - ATEN_WDR_TIMEOUT); -} - -static int get_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 *val) -{ - struct usb_device *dev = port->serial->dev; - int ret = 0; - __u16 wval; - struct ATENINTL_serial *a_serial; - __u16 minor = port->serial->minor; - - a_serial = usb_get_serial_data(port->serial); - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - - /* wval is same as application number */ - if (a_serial->ATEN2011_spectrum_2or4ports == 4) - wval = (((__u16)port->number - minor) + 1) << 8; - else { - if (((__u16) port->number - minor) == 0) - wval = (((__u16) port->number - minor) + 1) << 8; - else - wval = (((__u16) port->number - minor) + 2) << 8; - } - dbg("%s: application number is %x", __func__, wval); - ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ, - ATEN_RD_RTYPE, wval, reg, val, VENDOR_READ_LENGTH, - ATEN_WDR_TIMEOUT); - *val = (*val) & 0x00ff; - return ret; -} - -static int handle_newMsr(struct ATENINTL_port *port, __u8 newMsr) -{ - struct ATENINTL_port *ATEN2011_port; - struct async_icount *icount; - ATEN2011_port = port; - icount = &ATEN2011_port->icount; - if (newMsr & - (ATEN_MSR_DELTA_CTS | ATEN_MSR_DELTA_DSR | ATEN_MSR_DELTA_RI | - ATEN_MSR_DELTA_CD)) { - icount = &ATEN2011_port->icount; - - /* update input line counters */ - if (newMsr & ATEN_MSR_DELTA_CTS) - icount->cts++; - if (newMsr & ATEN_MSR_DELTA_DSR) - icount->dsr++; - if (newMsr & ATEN_MSR_DELTA_CD) - icount->dcd++; - if (newMsr & ATEN_MSR_DELTA_RI) - icount->rng++; - } - - return 0; -} - -static int handle_newLsr(struct ATENINTL_port *port, __u8 newLsr) -{ - struct async_icount *icount; - - dbg("%s - %02x", __func__, newLsr); - - if (newLsr & SERIAL_LSR_BI) { - /* - * Parity and Framing errors only count if they occur exclusive - * of a break being received. - */ - newLsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI); - } - - /* update input line counters */ - icount = &port->icount; - if (newLsr & SERIAL_LSR_BI) - icount->brk++; - if (newLsr & SERIAL_LSR_OE) - icount->overrun++; - if (newLsr & SERIAL_LSR_PE) - icount->parity++; - if (newLsr & SERIAL_LSR_FE) - icount->frame++; - - return 0; -} - -static void ATEN2011_control_callback(struct urb *urb) -{ - unsigned char *data; - struct ATENINTL_port *ATEN2011_port; - __u8 regval = 0x0; - - switch (urb->status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", __func__, - urb->status); - return; - default: - dbg("%s - nonzero urb status received: %d", __func__, - urb->status); - goto exit; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - dbg("%s urb buffer size is %d", __func__, urb->actual_length); - dbg("%s ATEN2011_port->MsrLsr is %d port %d", __func__, - ATEN2011_port->MsrLsr, ATEN2011_port->port_num); - data = urb->transfer_buffer; - regval = (__u8) data[0]; - dbg("%s data is %x", __func__, regval); - if (ATEN2011_port->MsrLsr == 0) - handle_newMsr(ATEN2011_port, regval); - else if (ATEN2011_port->MsrLsr == 1) - handle_newLsr(ATEN2011_port, regval); - -exit: - return; -} - -static int ATEN2011_get_reg(struct ATENINTL_port *ATEN, __u16 Wval, __u16 reg, - __u16 *val) -{ - struct usb_device *dev = ATEN->port->serial->dev; - struct usb_ctrlrequest *dr = NULL; - unsigned char *buffer = NULL; - int ret = 0; - buffer = (__u8 *) ATEN->ctrl_buf; - - dr = (void *)(buffer + 2); - dr->bRequestType = ATEN_RD_RTYPE; - dr->bRequest = ATEN_RDREQ; - dr->wValue = cpu_to_le16(Wval); - dr->wIndex = cpu_to_le16(reg); - dr->wLength = cpu_to_le16(2); - - usb_fill_control_urb(ATEN->control_urb, dev, usb_rcvctrlpipe(dev, 0), - (unsigned char *)dr, buffer, 2, - ATEN2011_control_callback, ATEN); - ATEN->control_urb->transfer_buffer_length = 2; - ret = usb_submit_urb(ATEN->control_urb, GFP_ATOMIC); - return ret; -} - -static void ATEN2011_interrupt_callback(struct urb *urb) -{ - int result; - int length; - struct ATENINTL_port *ATEN2011_port; - struct ATENINTL_serial *ATEN2011_serial; - struct usb_serial *serial; - __u16 Data; - unsigned char *data; - __u8 sp[5], st; - int i; - __u16 wval; - int minor; - - dbg("%s", " : Entering"); - - ATEN2011_serial = (struct ATENINTL_serial *)urb->context; - - switch (urb->status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", __func__, - urb->status); - return; - default: - dbg("%s - nonzero urb status received: %d", __func__, - urb->status); - goto exit; - } - length = urb->actual_length; - data = urb->transfer_buffer; - - serial = ATEN2011_serial->serial; - - /* ATENINTL get 5 bytes - * Byte 1 IIR Port 1 (port.number is 0) - * Byte 2 IIR Port 2 (port.number is 1) - * Byte 3 IIR Port 3 (port.number is 2) - * Byte 4 IIR Port 4 (port.number is 3) - * Byte 5 FIFO status for both */ - - if (length && length > 5) { - dbg("%s", "Wrong data !!!"); - return; - } - - /* MATRIX */ - if (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 4) { - sp[0] = (__u8) data[0]; - sp[1] = (__u8) data[1]; - sp[2] = (__u8) data[2]; - sp[3] = (__u8) data[3]; - st = (__u8) data[4]; - } else { - sp[0] = (__u8) data[0]; - sp[1] = (__u8) data[2]; - /* sp[2]=(__u8)data[2]; */ - /* sp[3]=(__u8)data[3]; */ - st = (__u8) data[4]; - - } - for (i = 0; i < serial->num_ports; i++) { - ATEN2011_port = usb_get_serial_port_data(serial->port[i]); - minor = serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (i != 0)) - wval = - (((__u16) serial->port[i]->number - - (__u16) (minor)) + 2) << 8; - else - wval = - (((__u16) serial->port[i]->number - - (__u16) (minor)) + 1) << 8; - if (ATEN2011_port->open != 0) { - if (sp[i] & 0x01) { - dbg("SP%d No Interrupt !!!", i); - } else { - switch (sp[i] & 0x0f) { - case SERIAL_IIR_RLS: - dbg("Serial Port %d: Receiver status error or address bit detected in 9-bit mode", i); - ATEN2011_port->MsrLsr = 1; - ATEN2011_get_reg(ATEN2011_port, wval, - LINE_STATUS_REGISTER, - &Data); - break; - case SERIAL_IIR_MS: - dbg("Serial Port %d: Modem status change", i); - ATEN2011_port->MsrLsr = 0; - ATEN2011_get_reg(ATEN2011_port, wval, - MODEM_STATUS_REGISTER, - &Data); - break; - } - } - } - - } -exit: - if (ATEN2011_serial->status_polling_started == 0) - return; - - result = usb_submit_urb(urb, GFP_ATOMIC); - if (result) { - dev_err(&urb->dev->dev, - "%s - Error %d submitting interrupt urb\n", - __func__, result); - } - - return; -} - -static void ATEN2011_bulk_in_callback(struct urb *urb) -{ - int status; - unsigned char *data; - struct usb_serial *serial; - struct usb_serial_port *port; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct tty_struct *tty; - - if (urb->status) { - dbg("nonzero read bulk status received: %d", urb->status); - return; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - port = (struct usb_serial_port *)ATEN2011_port->port; - serial = port->serial; - - dbg("%s", "Entering..."); - - data = urb->transfer_buffer; - ATEN2011_serial = usb_get_serial_data(serial); - - if (urb->actual_length) { - tty = tty_port_tty_get(&ATEN2011_port->port->port); - if (tty) { - tty_buffer_request_room(tty, urb->actual_length); - tty_insert_flip_string(tty, data, urb->actual_length); - tty_flip_buffer_push(tty); - tty_kref_put(tty); - } - - ATEN2011_port->icount.rx += urb->actual_length; - dbg("ATEN2011_port->icount.rx is %d:", - ATEN2011_port->icount.rx); - } - - if (!ATEN2011_port->read_urb) { - dbg("%s", "URB KILLED !!!"); - return; - } - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - if (status) - dbg("usb_submit_urb(read bulk) failed, status = %d", status); - } -} - -static void ATEN2011_bulk_out_data_callback(struct urb *urb) -{ - struct ATENINTL_port *ATEN2011_port; - struct tty_struct *tty; - - if (urb->status) { - dbg("nonzero write bulk status received:%d", urb->status); - return; - } - - ATEN2011_port = (struct ATENINTL_port *)urb->context; - - dbg("%s", "Entering ........."); - - tty = tty_port_tty_get(&ATEN2011_port->port->port); - - if (tty && ATEN2011_port->open) - /* tell the tty driver that something has changed */ - tty_wakeup(tty); - - /* schedule_work(&ATEN2011_port->port->work); */ - tty_kref_put(tty); - -} - -#ifdef ATENSerialProbe -static int ATEN2011_serial_probe(struct usb_serial *serial, - const struct usb_device_id *id) -{ - - /*need to implement the mode_reg reading and updating\ - structures usb_serial_ device_type\ - (i.e num_ports, num_bulkin,bulkout etc) */ - /* Also we can update the changes attach */ - return 1; -} -#endif - -static int ATEN2011_open(struct tty_struct *tty, struct usb_serial_port *port, - struct file *filp) -{ - int response; - int j; - struct usb_serial *serial; - struct urb *urb; - __u16 Data; - int status; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct ktermios tmp_termios; - int minor; - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -ENODEV; - - ATEN2011_serial = usb_get_serial_data(serial); - if (ATEN2011_serial == NULL) - return -ENODEV; - - /* increment the number of opened ports counter here */ - ATEN2011_serial->NoOfOpenPorts++; - - usb_clear_halt(serial->dev, port->write_urb->pipe); - usb_clear_halt(serial->dev, port->read_urb->pipe); - - /* Initialising the write urb pool */ - for (j = 0; j < NUM_URBS; ++j) { - urb = usb_alloc_urb(0, GFP_ATOMIC); - ATEN2011_port->write_urb_pool[j] = urb; - - if (urb == NULL) { - err("No more urbs???"); - continue; - } - - urb->transfer_buffer = NULL; - urb->transfer_buffer = - kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - if (!urb->transfer_buffer) { - err("%s-out of memory for urb buffers.", __func__); - continue; - } - } - -/***************************************************************************** - * Initialize ATEN2011 -- Write Init values to corresponding Registers - * - * Register Index - * 1 : IER - * 2 : FCR - * 3 : LCR - * 4 : MCR - * - * 0x08 : SP1/2 Control Reg - *****************************************************************************/ - -/* NEED to check the fallowing Block */ - - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - if (status < 0) { - dbg("Reading Spreg failed"); - return -1; - } - Data |= 0x80; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("writing Spreg failed"); - return -1; - } - - Data &= ~0x80; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("writing Spreg failed"); - return -1; - } - -/* End of block to be checked */ -/**************************CHECK***************************/ - - if (RS485mode == 0) - Data = 0xC0; - else - Data = 0x00; - status = set_uart_reg(port, SCRATCH_PAD_REGISTER, Data); - if (status < 0) { - dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x", status); - return -1; - } else - dbg("SCRATCH_PAD_REGISTER Writing success status%d", status); - -/**************************CHECK***************************/ - - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - if (status < 0) { - dbg("Reading Controlreg failed"); - return -1; - } - Data |= 0x08; /* Driver done bit */ - Data |= 0x20; /* rx_disable */ - status = 0; - status = - set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - if (status < 0) { - dbg("writing Controlreg failed"); - return -1; - } - /* - * do register settings here - * Set all regs to the device default values. - * First Disable all interrupts. - */ - - Data = 0x00; - status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - if (status < 0) { - dbg("disableing interrupts failed"); - return -1; - } - /* Set FIFO_CONTROL_REGISTER to the default value */ - Data = 0x00; - status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing FIFO_CONTROL_REGISTER failed"); - return -1; - } - - Data = 0xcf; /* chk */ - status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing FIFO_CONTROL_REGISTER failed"); - return -1; - } - - Data = 0x03; /* LCR_BITS_8 */ - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - ATEN2011_port->shadowLCR = Data; - - Data = 0x0b; /* MCR_DTR|MCR_RTS|MCR_MASTER_IE */ - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - ATEN2011_port->shadowMCR = Data; - -#ifdef Check - Data = 0x00; - status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); - ATEN2011_port->shadowLCR = Data; - - Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */ - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - Data = 0x0c; - status = set_uart_reg(port, DIVISOR_LATCH_LSB, Data); - - Data = 0x0; - status = set_uart_reg(port, DIVISOR_LATCH_MSB, Data); - - Data = 0x00; - status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); - -/* Data = ATEN2011_port->shadowLCR; */ /* data latch disable */ - Data = Data & ~SERIAL_LCR_DLAB; - status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - ATEN2011_port->shadowLCR = Data; -#endif - /* clearing Bulkin and Bulkout Fifo */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - - Data = Data | 0x0c; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - - Data = Data & ~0x0c; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - /* Finally enable all interrupts */ - Data = 0x0; - Data = 0x0c; - status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - /* clearing rx_disable */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - Data = Data & ~0x20; - status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - - /* rx_negate */ - Data = 0x0; - status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data); - Data = Data | 0x10; - status = 0; - status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data); - - /* - * Check to see if we've set up our endpoint info yet - * (can't set it up in ATEN2011_startup as the structures - * were not set up at that time.) - */ - if (ATEN2011_serial->NoOfOpenPorts == 1) { - /* start the status polling here */ - ATEN2011_serial->status_polling_started = 1; - /* If not yet set, Set here */ - ATEN2011_serial->interrupt_in_buffer = - serial->port[0]->interrupt_in_buffer; - ATEN2011_serial->interrupt_in_endpoint = - serial->port[0]->interrupt_in_endpointAddress; - ATEN2011_serial->interrupt_read_urb = - serial->port[0]->interrupt_in_urb; - - /* set up interrupt urb */ - usb_fill_int_urb(ATEN2011_serial->interrupt_read_urb, - serial->dev, - usb_rcvintpipe(serial->dev, - ATEN2011_serial-> - interrupt_in_endpoint), - ATEN2011_serial->interrupt_in_buffer, - ATEN2011_serial->interrupt_read_urb-> - transfer_buffer_length, - ATEN2011_interrupt_callback, ATEN2011_serial, - ATEN2011_serial->interrupt_read_urb->interval); - - /* start interrupt read for ATEN2011 * - * will continue as long as ATEN2011 is connected */ - - response = - usb_submit_urb(ATEN2011_serial->interrupt_read_urb, - GFP_KERNEL); - if (response) { - dbg("%s - Error %d submitting interrupt urb", - __func__, response); - } - - } - - /* - * See if we've set up our endpoint info yet - * (can't set it up in ATEN2011_startup as the - * structures were not set up at that time.) - */ - - dbg("port number is %d", port->number); - dbg("serial number is %d", port->serial->minor); - dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress); - dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress); - dbg("Interrupt endpoint is %d", - port->interrupt_in_endpointAddress); - dbg("port's number in the device is %d", ATEN2011_port->port_num); - ATEN2011_port->bulk_in_buffer = port->bulk_in_buffer; - ATEN2011_port->bulk_in_endpoint = port->bulk_in_endpointAddress; - ATEN2011_port->read_urb = port->read_urb; - ATEN2011_port->bulk_out_endpoint = port->bulk_out_endpointAddress; - - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - - /* set up our bulk in urb */ - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (((__u16) port->number - (__u16) (minor)) != 0)) { - usb_fill_bulk_urb(ATEN2011_port->read_urb, serial->dev, - usb_rcvbulkpipe(serial->dev, - (port-> - bulk_in_endpointAddress + - 2)), port->bulk_in_buffer, - ATEN2011_port->read_urb-> - transfer_buffer_length, - ATEN2011_bulk_in_callback, ATEN2011_port); - } else - usb_fill_bulk_urb(ATEN2011_port->read_urb, - serial->dev, - usb_rcvbulkpipe(serial->dev, - port-> - bulk_in_endpointAddress), - port->bulk_in_buffer, - ATEN2011_port->read_urb-> - transfer_buffer_length, - ATEN2011_bulk_in_callback, ATEN2011_port); - - dbg("ATEN2011_open: bulkin endpoint is %d", - port->bulk_in_endpointAddress); - response = usb_submit_urb(ATEN2011_port->read_urb, GFP_KERNEL); - if (response) { - err("%s - Error %d submitting control urb", __func__, - response); - } - - /* initialize our wait queues */ - init_waitqueue_head(&ATEN2011_port->wait_chase); - init_waitqueue_head(&ATEN2011_port->wait_command); - - /* initialize our icount structure */ - memset(&(ATEN2011_port->icount), 0x00, sizeof(ATEN2011_port->icount)); - - /* initialize our port settings */ - ATEN2011_port->shadowMCR = MCR_MASTER_IE; /* Must set to enable ints! */ - ATEN2011_port->chaseResponsePending = 0; - /* send a open port command */ - ATEN2011_port->open = 1; - /* ATEN2011_change_port_settings(ATEN2011_port,old_termios); */ - /* Setup termios */ - ATEN2011_set_termios(tty, port, &tmp_termios); - ATEN2011_port->icount.tx = 0; - ATEN2011_port->icount.rx = 0; - - dbg("usb_serial serial:%x ATEN2011_port:%x\nATEN2011_serial:%x usb_serial_port port:%x", - (unsigned int)serial, (unsigned int)ATEN2011_port, - (unsigned int)ATEN2011_serial, (unsigned int)port); - - return 0; - -} - -static int ATEN2011_chars_in_buffer(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int i; - int chars = 0; - struct ATENINTL_port *ATEN2011_port; - - /* dbg("%s"," ATEN2011_chars_in_buffer:entering ..........."); */ - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_break:leaving ..........."); - return -1; - } - - for (i = 0; i < NUM_URBS; ++i) - if (ATEN2011_port->write_urb_pool[i]->status == -EINPROGRESS) - chars += URB_TRANSFER_BUFFER_SIZE; - - dbg("%s - returns %d", __func__, chars); - return chars; - -} - -static void ATEN2011_block_until_tx_empty(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port) -{ - int timeout = HZ / 10; - int wait = 30; - int count; - - while (1) { - count = ATEN2011_chars_in_buffer(tty); - - /* Check for Buffer status */ - if (count <= 0) - return; - - /* Block the thread for a while */ - interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase, - timeout); - - /* No activity.. count down section */ - wait--; - if (wait == 0) { - dbg("%s - TIMEOUT", __func__); - return; - } else { - /* Reset timout value back to seconds */ - wait = 30; - } - } -} - -static void ATEN2011_close(struct tty_struct *tty, struct usb_serial_port *port, - struct file *filp) -{ - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - int no_urbs; - __u16 Data; - - dbg("%s", "ATEN2011_close:entering..."); - serial = port->serial; - - /* take the Adpater and port's private data */ - ATEN2011_serial = usb_get_serial_data(serial); - ATEN2011_port = usb_get_serial_port_data(port); - if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL)) - return; - - if (serial->dev) { - /* flush and block(wait) until tx is empty */ - ATEN2011_block_until_tx_empty(tty, ATEN2011_port); - } - /* kill the ports URB's */ - for (no_urbs = 0; no_urbs < NUM_URBS; no_urbs++) - usb_kill_urb(ATEN2011_port->write_urb_pool[no_urbs]); - /* Freeing Write URBs */ - for (no_urbs = 0; no_urbs < NUM_URBS; ++no_urbs) { - kfree(ATEN2011_port->write_urb_pool[no_urbs]->transfer_buffer); - usb_free_urb(ATEN2011_port->write_urb_pool[no_urbs]); - } - /* While closing port, shutdown all bulk read, write * - * and interrupt read if they exists */ - if (serial->dev) { - if (ATEN2011_port->write_urb) { - dbg("%s", "Shutdown bulk write"); - usb_kill_urb(ATEN2011_port->write_urb); - } - if (ATEN2011_port->read_urb) { - dbg("%s", "Shutdown bulk read"); - usb_kill_urb(ATEN2011_port->read_urb); - } - if ((&ATEN2011_port->control_urb)) { - dbg("%s", "Shutdown control read"); - /* usb_kill_urb (ATEN2011_port->control_urb); */ - - } - } - /* if(ATEN2011_port->ctrl_buf != NULL) */ - /* kfree(ATEN2011_port->ctrl_buf); */ - /* decrement the no.of open ports counter of an individual USB-serial adapter. */ - ATEN2011_serial->NoOfOpenPorts--; - dbg("NoOfOpenPorts in close%d:in port%d", - ATEN2011_serial->NoOfOpenPorts, port->number); - if (ATEN2011_serial->NoOfOpenPorts == 0) { - /* stop the stus polling here */ - ATEN2011_serial->status_polling_started = 0; - if (ATEN2011_serial->interrupt_read_urb) { - dbg("%s", "Shutdown interrupt_read_urb"); - /* ATEN2011_serial->interrupt_in_buffer=NULL; */ - /* usb_kill_urb (ATEN2011_serial->interrupt_read_urb); */ - } - } - if (ATEN2011_port->write_urb) { - /* if this urb had a transfer buffer already (old tx) free it */ - kfree(ATEN2011_port->write_urb->transfer_buffer); - usb_free_urb(ATEN2011_port->write_urb); - } - - /* clear the MCR & IER */ - Data = 0x00; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - Data = 0x00; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - ATEN2011_port->open = 0; - dbg("%s", "Leaving ............"); - -} - -static void ATEN2011_block_until_chase_response(struct tty_struct *tty, - struct ATENINTL_port - *ATEN2011_port) -{ - int timeout = 1 * HZ; - int wait = 10; - int count; - - while (1) { - count = ATEN2011_chars_in_buffer(tty); - - /* Check for Buffer status */ - if (count <= 0) { - ATEN2011_port->chaseResponsePending = 0; - return; - } - - /* Block the thread for a while */ - interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase, - timeout); - /* No activity.. count down section */ - wait--; - if (wait == 0) { - dbg("%s - TIMEOUT", __func__); - return; - } else { - /* Reset timout value back to seconds */ - wait = 10; - } - } - -} - -static void ATEN2011_break(struct tty_struct *tty, int break_state) -{ - struct usb_serial_port *port = tty->driver_data; - unsigned char data; - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - - dbg("%s", "Entering ..........."); - dbg("ATEN2011_break: Start"); - - serial = port->serial; - - ATEN2011_serial = usb_get_serial_data(serial); - ATEN2011_port = usb_get_serial_port_data(port); - - if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL)) - return; - - /* flush and chase */ - ATEN2011_port->chaseResponsePending = 1; - - if (serial->dev) { - /* flush and block until tx is empty */ - ATEN2011_block_until_chase_response(tty, ATEN2011_port); - } - - if (break_state == -1) - data = ATEN2011_port->shadowLCR | LCR_SET_BREAK; - else - data = ATEN2011_port->shadowLCR & ~LCR_SET_BREAK; - - ATEN2011_port->shadowLCR = data; - dbg("ATEN2011_break ATEN2011_port->shadowLCR is %x", - ATEN2011_port->shadowLCR); - set_uart_reg(port, LINE_CONTROL_REGISTER, ATEN2011_port->shadowLCR); - - return; -} - -static int ATEN2011_write_room(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int i; - int room = 0; - struct ATENINTL_port *ATEN2011_port; - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_break:leaving ..........."); - return -1; - } - - for (i = 0; i < NUM_URBS; ++i) - if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) - room += URB_TRANSFER_BUFFER_SIZE; - - dbg("%s - returns %d", __func__, room); - return room; - -} - -static int ATEN2011_write(struct tty_struct *tty, struct usb_serial_port *port, - const unsigned char *data, int count) -{ - int status; - int i; - int bytes_sent = 0; - int transfer_size; - int minor; - - struct ATENINTL_port *ATEN2011_port; - struct usb_serial *serial; - struct ATENINTL_serial *ATEN2011_serial; - struct urb *urb; - const unsigned char *current_position = data; - unsigned char *data1; - dbg("%s", "entering ..........."); - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - if (ATEN2011_port == NULL) { - dbg("%s", "ATEN2011_port is NULL"); - return -1; - } - - ATEN2011_serial = usb_get_serial_data(serial); - if (ATEN2011_serial == NULL) { - dbg("%s", "ATEN2011_serial is NULL"); - return -1; - } - - /* try to find a free urb in the list */ - urb = NULL; - - for (i = 0; i < NUM_URBS; ++i) { - if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) { - urb = ATEN2011_port->write_urb_pool[i]; - dbg("URB:%d", i); - break; - } - } - - if (urb == NULL) { - dbg("%s - no more free urbs", __func__); - goto exit; - } - - if (urb->transfer_buffer == NULL) { - urb->transfer_buffer = - kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); - - if (urb->transfer_buffer == NULL) { - err("%s no more kernel memory...", __func__); - goto exit; - } - } - transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE); - - memcpy(urb->transfer_buffer, current_position, transfer_size); - /* usb_serial_debug_data (__FILE__, __func__, transfer_size, urb->transfer_buffer); */ - - /* fill urb with data and submit */ - minor = port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2) - && (((__u16) port->number - (__u16) (minor)) != 0)) { - usb_fill_bulk_urb(urb, ATEN2011_serial->serial->dev, - usb_sndbulkpipe(ATEN2011_serial->serial->dev, - (port-> - bulk_out_endpointAddress) + - 2), urb->transfer_buffer, - transfer_size, - ATEN2011_bulk_out_data_callback, - ATEN2011_port); - } else - - usb_fill_bulk_urb(urb, - ATEN2011_serial->serial->dev, - usb_sndbulkpipe(ATEN2011_serial->serial->dev, - port-> - bulk_out_endpointAddress), - urb->transfer_buffer, transfer_size, - ATEN2011_bulk_out_data_callback, - ATEN2011_port); - - data1 = urb->transfer_buffer; - dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress); - /* for(i=0;i < urb->actual_length;i++) */ - /* dbg("Data is %c ",data1[i]); */ - - /* send it down the pipe */ - status = usb_submit_urb(urb, GFP_ATOMIC); - - if (status) { - err("%s - usb_submit_urb(write bulk) failed with status = %d", - __func__, status); - bytes_sent = status; - goto exit; - } - bytes_sent = transfer_size; - ATEN2011_port->icount.tx += transfer_size; - dbg("ATEN2011_port->icount.tx is %d:", ATEN2011_port->icount.tx); - -exit: - return bytes_sent; -} - -static void ATEN2011_throttle(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - int status; - - dbg("- port %d", port->number); - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s", "port not opened"); - return; - } - - dbg("%s", "Entering .......... "); - - if (!tty) { - dbg("%s - no tty available", __func__); - return; - } - - /* if we are implementing XON/XOFF, send the stop character */ - if (I_IXOFF(tty)) { - unsigned char stop_char = STOP_CHAR(tty); - status = ATEN2011_write(tty, port, &stop_char, 1); - if (status <= 0) - return; - } - - /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { - ATEN2011_port->shadowMCR &= ~MCR_RTS; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, - ATEN2011_port->shadowMCR); - if (status < 0) - return; - } - - return; -} - -static void ATEN2011_unthrottle(struct tty_struct *tty) -{ - struct usb_serial_port *port = tty->driver_data; - int status; - struct ATENINTL_port *ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - dbg("%s", "Entering .......... "); - - if (!tty) { - dbg("%s - no tty available", __func__); - return; - } - - /* if we are implementing XON/XOFF, send the start character */ - if (I_IXOFF(tty)) { - unsigned char start_char = START_CHAR(tty); - status = ATEN2011_write(tty, port, &start_char, 1); - if (status <= 0) - return; - } - - /* if we are implementing RTS/CTS, toggle that line */ - if (tty->termios->c_cflag & CRTSCTS) { - ATEN2011_port->shadowMCR |= MCR_RTS; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, - ATEN2011_port->shadowMCR); - if (status < 0) - return; - } - - return; -} - -static int ATEN2011_tiocmget(struct tty_struct *tty, struct file *file) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - unsigned int result; - __u16 msr; - __u16 mcr; - /* unsigned int mcr; */ - int status = 0; - ATEN2011_port = usb_get_serial_port_data(port); - - dbg("%s - port %d", __func__, port->number); - - if (ATEN2011_port == NULL) - return -ENODEV; - - status = get_uart_reg(port, MODEM_STATUS_REGISTER, &msr); - status = get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr); - /* mcr = ATEN2011_port->shadowMCR; */ - /* COMMENT2: the Fallowing three line are commented for updating only MSR values */ - result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) - | ((mcr & MCR_RTS) ? TIOCM_RTS : 0) - | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0) - | ((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0) - | ((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0) - | ((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0) - | ((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0); - - dbg("%s - 0x%04X", __func__, result); - - return result; -} - -static int ATEN2011_tiocmset(struct tty_struct *tty, struct file *file, - unsigned int set, unsigned int clear) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - unsigned int mcr; - unsigned int status; - - dbg("%s - port %d", __func__, port->number); - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -ENODEV; - - mcr = ATEN2011_port->shadowMCR; - if (clear & TIOCM_RTS) - mcr &= ~MCR_RTS; - if (clear & TIOCM_DTR) - mcr &= ~MCR_DTR; - if (clear & TIOCM_LOOP) - mcr &= ~MCR_LOOPBACK; - - if (set & TIOCM_RTS) - mcr |= MCR_RTS; - if (set & TIOCM_DTR) - mcr |= MCR_DTR; - if (set & TIOCM_LOOP) - mcr |= MCR_LOOPBACK; - - ATEN2011_port->shadowMCR = mcr; - - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr); - if (status < 0) { - dbg("setting MODEM_CONTROL_REGISTER Failed"); - return -1; - } - - return 0; -} - -static void ATEN2011_set_termios(struct tty_struct *tty, - struct usb_serial_port *port, - struct ktermios *old_termios) -{ - int status; - unsigned int cflag; - struct usb_serial *serial; - struct ATENINTL_port *ATEN2011_port; - - dbg("ATEN2011_set_termios: START"); - - serial = port->serial; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return; - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - dbg("%s", "setting termios - "); - - cflag = tty->termios->c_cflag; - - dbg("%s - cflag %08x iflag %08x", __func__, - tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag)); - - if (old_termios) { - dbg("%s - old clfag %08x old iflag %08x", __func__, - old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag)); - } - - dbg("%s - port %d", __func__, port->number); - - /* change the port settings to the new ones specified */ - - ATEN2011_change_port_settings(tty, ATEN2011_port, old_termios); - - if (!ATEN2011_port->read_urb) { - dbg("%s", "URB KILLED !!!!!"); - return; - } - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - if (status) { - dbg - (" usb_submit_urb(read bulk) failed, status = %d", - status); - } - } - return; -} - -static int get_lsr_info(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - int count; - unsigned int result = 0; - - count = ATEN2011_chars_in_buffer(tty); - if (count == 0) { - dbg("%s -- Empty", __func__); - result = TIOCSER_TEMT; - } - - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - return 0; -} - -static int get_number_bytes_avail(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - unsigned int result = 0; - - if (!tty) - return -ENOIOCTLCMD; - - result = tty->read_cnt; - - dbg("%s(%d) = %d", __func__, ATEN2011_port->port->number, result); - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - - return -ENOIOCTLCMD; -} - -static int set_modem_info(struct ATENINTL_port *ATEN2011_port, unsigned int cmd, - unsigned int __user *value) -{ - unsigned int mcr; - unsigned int arg; - __u16 Data; - int status; - struct usb_serial_port *port; - - if (ATEN2011_port == NULL) - return -1; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - mcr = ATEN2011_port->shadowMCR; - - if (copy_from_user(&arg, value, sizeof(int))) - return -EFAULT; - - switch (cmd) { - case TIOCMBIS: - if (arg & TIOCM_RTS) - mcr |= MCR_RTS; - if (arg & TIOCM_DTR) - mcr |= MCR_RTS; - if (arg & TIOCM_LOOP) - mcr |= MCR_LOOPBACK; - break; - - case TIOCMBIC: - if (arg & TIOCM_RTS) - mcr &= ~MCR_RTS; - if (arg & TIOCM_DTR) - mcr &= ~MCR_RTS; - if (arg & TIOCM_LOOP) - mcr &= ~MCR_LOOPBACK; - break; - - case TIOCMSET: - /* turn off the RTS and DTR and LOOPBACK - * and then only turn on what was asked to */ - mcr &= ~(MCR_RTS | MCR_DTR | MCR_LOOPBACK); - mcr |= ((arg & TIOCM_RTS) ? MCR_RTS : 0); - mcr |= ((arg & TIOCM_DTR) ? MCR_DTR : 0); - mcr |= ((arg & TIOCM_LOOP) ? MCR_LOOPBACK : 0); - break; - } - - ATEN2011_port->shadowMCR = mcr; - - Data = ATEN2011_port->shadowMCR; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("setting MODEM_CONTROL_REGISTER Failed"); - return -1; - } - - return 0; -} - -static int get_modem_info(struct ATENINTL_port *ATEN2011_port, - unsigned int __user *value) -{ - unsigned int result = 0; - __u16 msr; - unsigned int mcr = ATEN2011_port->shadowMCR; - int status; - - status = get_uart_reg(ATEN2011_port->port, MODEM_STATUS_REGISTER, &msr); - result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) /* 0x002 */ - |((mcr & MCR_RTS) ? TIOCM_RTS : 0) /* 0x004 */ - |((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0) /* 0x020 */ - |((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0) /* 0x040 */ - |((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0) /* 0x080 */ - |((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0); /* 0x100 */ - - dbg("%s -- %x", __func__, result); - - if (copy_to_user(value, &result, sizeof(int))) - return -EFAULT; - return 0; -} - -static int get_serial_info(struct ATENINTL_port *ATEN2011_port, - struct serial_struct __user *retinfo) -{ - struct serial_struct tmp; - - if (ATEN2011_port == NULL) - return -1; - - if (!retinfo) - return -EFAULT; - - memset(&tmp, 0, sizeof(tmp)); - - tmp.type = PORT_16550A; - tmp.line = ATEN2011_port->port->serial->minor; - if (tmp.line == SERIAL_TTY_NO_MINOR) - tmp.line = 0; - tmp.port = ATEN2011_port->port->number; - tmp.irq = 0; - tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE; - tmp.baud_base = 9600; - tmp.close_delay = 5 * HZ; - tmp.closing_wait = 30 * HZ; - - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) - return -EFAULT; - return 0; -} - -static int ATEN2011_ioctl(struct tty_struct *tty, struct file *file, - unsigned int cmd, unsigned long arg) -{ - struct usb_serial_port *port = tty->driver_data; - struct ATENINTL_port *ATEN2011_port; - struct async_icount cnow; - struct async_icount cprev; - struct serial_icounter_struct icount; - int ATENret = 0; - unsigned int __user *user_arg = (unsigned int __user *)arg; - - ATEN2011_port = usb_get_serial_port_data(port); - - if (ATEN2011_port == NULL) - return -1; - - dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd); - - switch (cmd) { - /* return number of bytes available */ - - case TIOCINQ: - dbg("%s (%d) TIOCINQ", __func__, port->number); - return get_number_bytes_avail(tty, ATEN2011_port, user_arg); - break; - - case TIOCOUTQ: - dbg("%s (%d) TIOCOUTQ", __func__, port->number); - return put_user(ATEN2011_chars_in_buffer(tty), user_arg); - break; - - case TIOCSERGETLSR: - dbg("%s (%d) TIOCSERGETLSR", __func__, port->number); - return get_lsr_info(tty, ATEN2011_port, user_arg); - return 0; - - case TIOCMBIS: - case TIOCMBIC: - case TIOCMSET: - dbg("%s (%d) TIOCMSET/TIOCMBIC/TIOCMSET", __func__, - port->number); - ATENret = set_modem_info(ATEN2011_port, cmd, user_arg); - return ATENret; - - case TIOCMGET: - dbg("%s (%d) TIOCMGET", __func__, port->number); - return get_modem_info(ATEN2011_port, user_arg); - - case TIOCGSERIAL: - dbg("%s (%d) TIOCGSERIAL", __func__, port->number); - return get_serial_info(ATEN2011_port, - (struct serial_struct __user *)arg); - - case TIOCSSERIAL: - dbg("%s (%d) TIOCSSERIAL", __func__, port->number); - break; - - case TIOCMIWAIT: - dbg("%s (%d) TIOCMIWAIT", __func__, port->number); - cprev = ATEN2011_port->icount; - while (1) { - /* see if a signal did it */ - if (signal_pending(current)) - return -ERESTARTSYS; - cnow = ATEN2011_port->icount; - if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && - cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) - return -EIO; /* no change => error */ - if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { - return 0; - } - cprev = cnow; - } - /* NOTREACHED */ - break; - - case TIOCGICOUNT: - cnow = ATEN2011_port->icount; - icount.cts = cnow.cts; - icount.dsr = cnow.dsr; - icount.rng = cnow.rng; - icount.dcd = cnow.dcd; - icount.rx = cnow.rx; - icount.tx = cnow.tx; - icount.frame = cnow.frame; - icount.overrun = cnow.overrun; - icount.parity = cnow.parity; - icount.brk = cnow.brk; - icount.buf_overrun = cnow.buf_overrun; - - dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__, - port->number, icount.rx, icount.tx); - if (copy_to_user((void __user *)arg, &icount, sizeof(icount))) - return -EFAULT; - return 0; - - default: - break; - } - - return -ENOIOCTLCMD; -} - -static int ATEN2011_calc_baud_rate_divisor(int baudRate, int *divisor, - __u16 *clk_sel_val) -{ - dbg("%s - %d", __func__, baudRate); - - if (baudRate <= 115200) { - *divisor = 115200 / baudRate; - *clk_sel_val = 0x0; - } - if ((baudRate > 115200) && (baudRate <= 230400)) { - *divisor = 230400 / baudRate; - *clk_sel_val = 0x10; - } else if ((baudRate > 230400) && (baudRate <= 403200)) { - *divisor = 403200 / baudRate; - *clk_sel_val = 0x20; - } else if ((baudRate > 403200) && (baudRate <= 460800)) { - *divisor = 460800 / baudRate; - *clk_sel_val = 0x30; - } else if ((baudRate > 460800) && (baudRate <= 806400)) { - *divisor = 806400 / baudRate; - *clk_sel_val = 0x40; - } else if ((baudRate > 806400) && (baudRate <= 921600)) { - *divisor = 921600 / baudRate; - *clk_sel_val = 0x50; - } else if ((baudRate > 921600) && (baudRate <= 1572864)) { - *divisor = 1572864 / baudRate; - *clk_sel_val = 0x60; - } else if ((baudRate > 1572864) && (baudRate <= 3145728)) { - *divisor = 3145728 / baudRate; - *clk_sel_val = 0x70; - } - return 0; -} - -static int ATEN2011_send_cmd_write_baud_rate(struct ATENINTL_port - *ATEN2011_port, int baudRate) -{ - int divisor = 0; - int status; - __u16 Data; - unsigned char number; - __u16 clk_sel_val; - struct usb_serial_port *port; - int minor; - - if (ATEN2011_port == NULL) - return -1; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - dbg("%s", "Entering .......... "); - - minor = ATEN2011_port->port->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - number = ATEN2011_port->port->number - minor; - - dbg("%s - port = %d, baud = %d", __func__, - ATEN2011_port->port->number, baudRate); - /* reset clk_uart_sel in spregOffset */ - if (baudRate > 115200) { -#ifdef HW_flow_control - /* - * NOTE: need to see the pther register to modify - * setting h/w flow control bit to 1; - */ - /* Data = ATEN2011_port->shadowMCR; */ - Data = 0x2b; - ATEN2011_port->shadowMCR = Data; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } -#endif - - } else { -#ifdef HW_flow_control - /* setting h/w flow control bit to 0; */ - /* Data = ATEN2011_port->shadowMCR; */ - Data = 0xb; - ATEN2011_port->shadowMCR = Data; - status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } -#endif - - } - - if (1) /* baudRate <= 115200) */ { - clk_sel_val = 0x0; - Data = 0x0; - status = - ATEN2011_calc_baud_rate_divisor(baudRate, &divisor, - &clk_sel_val); - status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data); - if (status < 0) { - dbg("reading spreg failed in set_serial_baud"); - return -1; - } - Data = (Data & 0x8f) | clk_sel_val; - status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data); - if (status < 0) { - dbg("Writing spreg failed in set_serial_baud"); - return -1; - } - /* Calculate the Divisor */ - - if (status) { - err("%s - bad baud rate", __func__); - dbg("%s", "bad baud rate"); - return status; - } - /* Enable access to divisor latch */ - Data = ATEN2011_port->shadowLCR | SERIAL_LCR_DLAB; - ATEN2011_port->shadowLCR = Data; - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - /* Write the divisor */ - Data = (unsigned char)(divisor & 0xff); - dbg("set_serial_baud Value to write DLL is %x", Data); - set_uart_reg(port, DIVISOR_LATCH_LSB, Data); - - Data = (unsigned char)((divisor & 0xff00) >> 8); - dbg("set_serial_baud Value to write DLM is %x", Data); - set_uart_reg(port, DIVISOR_LATCH_MSB, Data); - - /* Disable access to divisor latch */ - Data = ATEN2011_port->shadowLCR & ~SERIAL_LCR_DLAB; - ATEN2011_port->shadowLCR = Data; - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - } - - return status; -} - -static void ATEN2011_change_port_settings(struct tty_struct *tty, - struct ATENINTL_port *ATEN2011_port, - struct ktermios *old_termios) -{ - int baud; - unsigned cflag; - unsigned iflag; - __u8 lData; - __u8 lParity; - __u8 lStop; - int status; - __u16 Data; - struct usb_serial_port *port; - struct usb_serial *serial; - - if (ATEN2011_port == NULL) - return; - - port = (struct usb_serial_port *)ATEN2011_port->port; - - serial = port->serial; - - dbg("%s - port %d", __func__, ATEN2011_port->port->number); - - if (!ATEN2011_port->open) { - dbg("%s - port not opened", __func__); - return; - } - - if ((!tty) || (!tty->termios)) { - dbg("%s - no tty structures", __func__); - return; - } - - dbg("%s", "Entering .......... "); - - lData = LCR_BITS_8; - lStop = LCR_STOP_1; - lParity = LCR_PAR_NONE; - - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; - - /* Change the number of bits */ - - /* COMMENT1: the below Line"if(cflag & CSIZE)" is added for the errors we get for serial loop data test i.e serial_loopback.pl -v */ - /* if(cflag & CSIZE) */ - { - switch (cflag & CSIZE) { - case CS5: - lData = LCR_BITS_5; - break; - - case CS6: - lData = LCR_BITS_6; - break; - - case CS7: - lData = LCR_BITS_7; - break; - default: - case CS8: - lData = LCR_BITS_8; - break; - } - } - /* Change the Parity bit */ - if (cflag & PARENB) { - if (cflag & PARODD) { - lParity = LCR_PAR_ODD; - dbg("%s - parity = odd", __func__); - } else { - lParity = LCR_PAR_EVEN; - dbg("%s - parity = even", __func__); - } - - } else { - dbg("%s - parity = none", __func__); - } - - if (cflag & CMSPAR) - lParity = lParity | 0x20; - - /* Change the Stop bit */ - if (cflag & CSTOPB) { - lStop = LCR_STOP_2; - dbg("%s - stop bits = 2", __func__); - } else { - lStop = LCR_STOP_1; - dbg("%s - stop bits = 1", __func__); - } - - /* Update the LCR with the correct value */ - ATEN2011_port->shadowLCR &= - ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK); - ATEN2011_port->shadowLCR |= (lData | lParity | lStop); - - dbg - ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is %x", - ATEN2011_port->shadowLCR); - /* Disable Interrupts */ - Data = 0x00; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - Data = 0x00; - set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - - Data = 0xcf; - set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); - - /* Send the updated LCR value to the ATEN2011 */ - Data = ATEN2011_port->shadowLCR; - - set_uart_reg(port, LINE_CONTROL_REGISTER, Data); - - Data = 0x00b; - ATEN2011_port->shadowMCR = Data; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - Data = 0x00b; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - - /* set up the MCR register and send it to the ATEN2011 */ - - ATEN2011_port->shadowMCR = MCR_MASTER_IE; - if (cflag & CBAUD) - ATEN2011_port->shadowMCR |= (MCR_DTR | MCR_RTS); - - if (cflag & CRTSCTS) - ATEN2011_port->shadowMCR |= (MCR_XON_ANY); - else - ATEN2011_port->shadowMCR &= ~(MCR_XON_ANY); - - Data = ATEN2011_port->shadowMCR; - set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); - - /* Determine divisor based on baud rate */ - baud = tty_get_baud_rate(tty); - - if (!baud) { - /* pick a default, any default... */ - dbg("%s", "Picked default baud..."); - baud = 9600; - } - - dbg("%s - baud rate = %d", __func__, baud); - status = ATEN2011_send_cmd_write_baud_rate(ATEN2011_port, baud); - - /* Enable Interrupts */ - Data = 0x0c; - set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); - - if (ATEN2011_port->read_urb->status != -EINPROGRESS) { - ATEN2011_port->read_urb->dev = serial->dev; - - status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC); - - if (status) { - dbg - (" usb_submit_urb(read bulk) failed, status = %d", - status); - } - } - dbg - ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is End %x", - ATEN2011_port->shadowLCR); - - return; -} - -static int ATEN2011_calc_num_ports(struct usb_serial *serial) -{ - - __u16 Data = 0x00; - int ret = 0; - int ATEN2011_2or4ports; - ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), - ATEN_RDREQ, ATEN_RD_RTYPE, 0, GPIO_REGISTER, - &Data, VENDOR_READ_LENGTH, ATEN_WDR_TIMEOUT); - -/* ghostgum: here is where the problem appears to bet */ -/* Which of the following are needed? */ -/* Greg used the serial->type->num_ports=2 */ -/* But the code in the ATEN2011_open relies on serial->num_ports=2 */ - if ((Data & 0x01) == 0) { - ATEN2011_2or4ports = 2; - serial->type->num_ports = 2; - serial->num_ports = 2; - } - /* else if(serial->interface->cur_altsetting->desc.bNumEndpoints == 9) */ - else { - ATEN2011_2or4ports = 4; - serial->type->num_ports = 4; - serial->num_ports = 4; - - } - - return ATEN2011_2or4ports; -} - -static int ATEN2011_startup(struct usb_serial *serial) -{ - struct ATENINTL_serial *ATEN2011_serial; - struct ATENINTL_port *ATEN2011_port; - struct usb_device *dev; - int i, status; - int minor; - - __u16 Data; - dbg("%s", " ATEN2011_startup :entering.........."); - - if (!serial) { - dbg("%s", "Invalid Handler"); - return -1; - } - - dev = serial->dev; - - dbg("%s", "Entering..."); - - /* create our private serial structure */ - ATEN2011_serial = kzalloc(sizeof(struct ATENINTL_serial), GFP_KERNEL); - if (ATEN2011_serial == NULL) { - err("%s - Out of memory", __func__); - return -ENOMEM; - } - - /* resetting the private structure field values to zero */ - memset(ATEN2011_serial, 0, sizeof(struct ATENINTL_serial)); - - ATEN2011_serial->serial = serial; - /* initilize status polling flag to 0 */ - ATEN2011_serial->status_polling_started = 0; - - usb_set_serial_data(serial, ATEN2011_serial); - ATEN2011_serial->ATEN2011_spectrum_2or4ports = - ATEN2011_calc_num_ports(serial); - /* we set up the pointers to the endpoints in the ATEN2011_open * - * function, as the structures aren't created yet. */ - - /* set up port private structures */ - for (i = 0; i < serial->num_ports; ++i) { - ATEN2011_port = - kmalloc(sizeof(struct ATENINTL_port), GFP_KERNEL); - if (ATEN2011_port == NULL) { - err("%s - Out of memory", __func__); - usb_set_serial_data(serial, NULL); - kfree(ATEN2011_serial); - return -ENOMEM; - } - memset(ATEN2011_port, 0, sizeof(struct ATENINTL_port)); - - /* - * Initialize all port interrupt end point to port 0 - * int endpoint. Our device has only one interrupt end point - * comman to all port - */ - /* serial->port[i]->interrupt_in_endpointAddress = serial->port[0]->interrupt_in_endpointAddress; */ - - ATEN2011_port->port = serial->port[i]; - usb_set_serial_port_data(serial->port[i], ATEN2011_port); - - minor = serial->port[i]->serial->minor; - if (minor == SERIAL_TTY_NO_MINOR) - minor = 0; - ATEN2011_port->port_num = - ((serial->port[i]->number - minor) + 1); - - if (ATEN2011_port->port_num == 1) { - ATEN2011_port->SpRegOffset = 0x0; - ATEN2011_port->ControlRegOffset = 0x1; - ATEN2011_port->DcrRegOffset = 0x4; - } else if ((ATEN2011_port->port_num == 2) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0x8; - ATEN2011_port->ControlRegOffset = 0x9; - ATEN2011_port->DcrRegOffset = 0x16; - } else if ((ATEN2011_port->port_num == 2) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 2)) { - ATEN2011_port->SpRegOffset = 0xa; - ATEN2011_port->ControlRegOffset = 0xb; - ATEN2011_port->DcrRegOffset = 0x19; - } else if ((ATEN2011_port->port_num == 3) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0xa; - ATEN2011_port->ControlRegOffset = 0xb; - ATEN2011_port->DcrRegOffset = 0x19; - } else if ((ATEN2011_port->port_num == 4) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == - 4)) { - ATEN2011_port->SpRegOffset = 0xc; - ATEN2011_port->ControlRegOffset = 0xd; - ATEN2011_port->DcrRegOffset = 0x1c; - } - - usb_set_serial_port_data(serial->port[i], ATEN2011_port); - - /* enable rx_disable bit in control register */ - - status = get_reg_sync(serial->port[i], - ATEN2011_port->ControlRegOffset, &Data); - if (status < 0) { - dbg("Reading ControlReg failed status-0x%x", - status); - break; - } else - dbg - ("ControlReg Reading success val is %x, status%d", - Data, status); - Data |= 0x08; /* setting driver done bit */ - Data |= 0x04; /* sp1_bit to have cts change reflect in modem status reg */ - - /* Data |= 0x20; */ /* rx_disable bit */ - status = set_reg_sync(serial->port[i], - ATEN2011_port->ControlRegOffset, Data); - if (status < 0) { - dbg - ("Writing ControlReg failed(rx_disable) status-0x%x", - status); - break; - } else - dbg - ("ControlReg Writing success(rx_disable) status%d", - status); - - /* - * Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2 - * and 0x24 in DCR3 - */ - Data = 0x01; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 0), - Data); - if (status < 0) { - dbg("Writing DCR0 failed status-0x%x", status); - break; - } else - dbg("DCR0 Writing success status%d", status); - - Data = 0x05; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 1), - Data); - if (status < 0) { - dbg("Writing DCR1 failed status-0x%x", status); - break; - } else - dbg("DCR1 Writing success status%d", status); - - Data = 0x24; - status = set_reg_sync(serial->port[i], - (__u16)(ATEN2011_port->DcrRegOffset + 2), - Data); - if (status < 0) { - dbg("Writing DCR2 failed status-0x%x", status); - break; - } else - dbg("DCR2 Writing success status%d", status); - - /* write values in clkstart0x0 and clkmulti 0x20 */ - Data = 0x0; - status = set_reg_sync(serial->port[i], CLK_START_VALUE_REGISTER, - Data); - if (status < 0) { - dbg - ("Writing CLK_START_VALUE_REGISTER failed status-0x%x", - status); - break; - } else - dbg - ("CLK_START_VALUE_REGISTER Writing success status%d", - status); - - Data = 0x20; - status = set_reg_sync(serial->port[i], CLK_MULTI_REGISTER, - Data); - if (status < 0) { - dbg - ("Writing CLK_MULTI_REGISTER failed status-0x%x", - status); - break; - } else - dbg("CLK_MULTI_REGISTER Writing success status%d", - status); - - /* Zero Length flag register */ - if ((ATEN2011_port->port_num != 1) - && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)) { - - Data = 0xff; - status = set_reg_sync(serial->port[i], - (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num)), - Data); - dbg("ZLIP offset%x", - (__u16) (ZLP_REG1 + - ((__u16) ATEN2011_port->port_num))); - if (status < 0) { - dbg - ("Writing ZLP_REG%d failed status-0x%x", - i + 2, status); - break; - } else - dbg("ZLP_REG%d Writing success status%d", - i + 2, status); - } else { - Data = 0xff; - status = set_reg_sync(serial->port[i], - (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num) - 0x1), - Data); - dbg("ZLIP offset%x", - (__u16) (ZLP_REG1 + - ((__u16) ATEN2011_port->port_num) - - 0x1)); - if (status < 0) { - dbg - ("Writing ZLP_REG%d failed status-0x%x", - i + 1, status); - break; - } else - dbg("ZLP_REG%d Writing success status%d", - i + 1, status); - - } - ATEN2011_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC); - ATEN2011_port->ctrl_buf = kmalloc(16, GFP_KERNEL); - - } - - /* Zero Length flag enable */ - Data = 0x0f; - status = set_reg_sync(serial->port[0], ZLP_REG5, Data); - if (status < 0) { - dbg("Writing ZLP_REG5 failed status-0x%x", status); - return -1; - } else - dbg("ZLP_REG5 Writing success status%d", status); - - /* setting configuration feature to one */ - usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), - (__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ); - return 0; -} - -static void ATEN2011_release(struct usb_serial *serial) -{ - int i; - struct ATENINTL_port *ATEN2011_port; - - /* check for the ports to be closed,close the ports and disconnect */ - - /* free private structure allocated for serial port * - * stop reads and writes on all ports */ - - for (i = 0; i < serial->num_ports; ++i) { - ATEN2011_port = usb_get_serial_port_data(serial->port[i]); - kfree(ATEN2011_port->ctrl_buf); - usb_kill_urb(ATEN2011_port->control_urb); - kfree(ATEN2011_port); - usb_set_serial_port_data(serial->port[i], NULL); - } - - /* free private structure allocated for serial device */ - - kfree(usb_get_serial_data(serial)); - usb_set_serial_data(serial, NULL); -} - -static struct usb_serial_driver aten_serial_driver = { - .driver = { - .owner = THIS_MODULE, - .name = "aten2011", - }, - .description = DRIVER_DESC, - .id_table = id_table, - .open = ATEN2011_open, - .close = ATEN2011_close, - .write = ATEN2011_write, - .write_room = ATEN2011_write_room, - .chars_in_buffer = ATEN2011_chars_in_buffer, - .throttle = ATEN2011_throttle, - .unthrottle = ATEN2011_unthrottle, - .calc_num_ports = ATEN2011_calc_num_ports, - - .ioctl = ATEN2011_ioctl, - .set_termios = ATEN2011_set_termios, - .break_ctl = ATEN2011_break, - .tiocmget = ATEN2011_tiocmget, - .tiocmset = ATEN2011_tiocmset, - .attach = ATEN2011_startup, - .release = ATEN2011_release, - .read_bulk_callback = ATEN2011_bulk_in_callback, - .read_int_callback = ATEN2011_interrupt_callback, -}; - -static struct usb_driver aten_driver = { - .name = "aten2011", - .probe = usb_serial_probe, - .disconnect = usb_serial_disconnect, - .id_table = id_table, -}; - -static int __init aten_init(void) -{ - int retval; - - /* Register with the usb serial */ - retval = usb_serial_register(&aten_serial_driver); - if (retval) - return retval; - - printk(KERN_INFO KBUILD_MODNAME ":" - DRIVER_DESC " " DRIVER_VERSION "\n"); - - /* Register with the usb */ - retval = usb_register(&aten_driver); - if (retval) - usb_serial_deregister(&aten_serial_driver); - - return retval; -} - -static void __exit aten_exit(void) -{ - usb_deregister(&aten_driver); - usb_serial_deregister(&aten_serial_driver); -} - -module_init(aten_init); -module_exit(aten_exit); - -/* Module information */ -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_LICENSE("GPL"); - -MODULE_PARM_DESC(debug, "Debug enabled or not"); -- cgit v1.2.3 From fb29900217bd89370974870d47cab07bad3e5ac4 Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Mon, 27 Jul 2009 12:01:03 +0300 Subject: staging: udlfb: Add vmalloc.h include Required for vmalloc_32 and vfree declarations on non-x86 platforms. Signed-off-by: Amit Kucheria Signed-off-by: Greg Kroah-Hartman --- drivers/staging/udlfb/udlfb.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/staging/udlfb/udlfb.c b/drivers/staging/udlfb/udlfb.c index 0ab9d15f3439..f5416af1e902 100644 --- a/drivers/staging/udlfb/udlfb.c +++ b/drivers/staging/udlfb/udlfb.c @@ -21,6 +21,7 @@ #include #include #include +#include #include "udlfb.h" -- cgit v1.2.3 From ce4adcc6e5320062e0d993eb75152d165aaabbe6 Mon Sep 17 00:00:00 2001 From: Andreas Eversberg Date: Mon, 27 Jul 2009 19:24:04 +0200 Subject: mISDN: Fix handling of receive buffer size in L1oIP The size of receive buffer pointer was used to get size of receive buffer instead of recvbuf_size itself, so only 4/8 bytes could be transfered. This is a regression to 2.6.30 introduced by commit 8c90e11e3543d7de612194a042a148caeaab5f1d ("mISDN: Use kernel_{send,recv}msg instead of open coding") Signed-off-by: Andreas Eversberg Signed-off-by: Karsten Keil Signed-off-by: Linus Torvalds --- drivers/isdn/mISDN/l1oip_core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 990e6a7e6674..c3b661a666cb 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -731,10 +731,10 @@ l1oip_socket_thread(void *data) while (!signal_pending(current)) { struct kvec iov = { .iov_base = recvbuf, - .iov_len = sizeof(recvbuf), + .iov_len = recvbuf_size, }; recvlen = kernel_recvmsg(socket, &msg, &iov, 1, - sizeof(recvbuf), 0); + recvbuf_size, 0); if (recvlen > 0) { l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen); } else { -- cgit v1.2.3 From f99aa3f9b67ca8c29dc29ef3fc453f0343206c46 Mon Sep 17 00:00:00 2001 From: "Carlos R. Mafra" Date: Mon, 13 Jul 2009 21:45:03 +0200 Subject: USB: option: Remove unused variable After commit f092c240494f2d807401d93f95f683909b90af96 ("USB: option: remove unnecessary and erroneous code") the variable 'serial' becomes unused, as gcc-4.3.2 points out: drivers/usb/serial/option.c: In function 'option_instat_callback': drivers/usb/serial/option.c:834: warning: unused variable 'serial' drivers/usb/serial/option.c: In function 'option_open': drivers/usb/serial/option.c:930: warning: unused variable 'serial' So I removed it. Signed-off-by: Carlos R. Mafra Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 98262dd552bb..77b9563ec43e 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -831,7 +831,6 @@ static void option_instat_callback(struct urb *urb) int status = urb->status; struct usb_serial_port *port = urb->context; struct option_port_private *portdata = usb_get_serial_port_data(port); - struct usb_serial *serial = port->serial; dbg("%s", __func__); dbg("%s: urb %p port %p has data %p", __func__, urb, port, portdata); @@ -927,7 +926,6 @@ static int option_open(struct tty_struct *tty, struct usb_serial_port *port, struct file *filp) { struct option_port_private *portdata; - struct usb_serial *serial = port->serial; int i, err; struct urb *urb; -- cgit v1.2.3 From 5f4fab91f2b12c12f0506b4da49ed199db8c64ed Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 13 Jul 2009 23:24:10 +0200 Subject: USB: let the option driver compile without CONFIG_PM This is needed for compilation without CONFIG_PM. Signed-off-by: Oliver Neukum Acked-by: Randy Dunlap Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 77b9563ec43e..7638d2632ff8 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -66,8 +66,10 @@ static int option_tiocmget(struct tty_struct *tty, struct file *file); static int option_tiocmset(struct tty_struct *tty, struct file *file, unsigned int set, unsigned int clear); static int option_send_setup(struct usb_serial_port *port); +#ifdef CONFIG_PM static int option_suspend(struct usb_serial *serial, pm_message_t message); static int option_resume(struct usb_serial *serial); +#endif /* Vendor and product IDs */ #define OPTION_VENDOR_ID 0x0AF0 @@ -555,8 +557,10 @@ static struct usb_driver option_driver = { .name = "option", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, +#ifdef CONFIG_PM .suspend = usb_serial_suspend, .resume = usb_serial_resume, +#endif .id_table = option_ids, .no_dynamic_id = 1, }; @@ -588,8 +592,10 @@ static struct usb_serial_driver option_1port_device = { .disconnect = option_disconnect, .release = option_release, .read_int_callback = option_instat_callback, +#ifdef CONFIG_PM .suspend = option_suspend, .resume = option_resume, +#endif }; static int debug; @@ -1185,6 +1191,7 @@ static void option_release(struct usb_serial *serial) } } +#ifdef CONFIG_PM static int option_suspend(struct usb_serial *serial, pm_message_t message) { dbg("%s entered", __func__); @@ -1243,6 +1250,7 @@ static int option_resume(struct usb_serial *serial) } return 0; } +#endif MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); -- cgit v1.2.3 From 7a777919bbeec3eac1d7904a728a60e9c2bb9c67 Mon Sep 17 00:00:00 2001 From: Giacomo Lozito Date: Mon, 13 Jul 2009 23:23:33 +0200 Subject: USB: storage: raise timeout in usb_stor_Bulk_max_lun Requests to get max LUN, for certain USB storage devices, require a longer timeout before a correct reply is returned. This happens for a Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set to 0, thus losing functionality, because of the timeout occurring too quickly. Raising the timeout value fixes the issue and might help other devices to return a correct max LUN value as well. Signed-off-by: Giacomo Lozito Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/transport.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index fcb320217218..e20dc525d177 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -961,7 +961,7 @@ int usb_stor_Bulk_max_lun(struct us_data *us) US_BULK_GET_MAX_LUN, USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE, - 0, us->ifnum, us->iobuf, 1, HZ); + 0, us->ifnum, us->iobuf, 1, 10*HZ); US_DEBUGP("GetMaxLUN command result is %d, data is %d\n", result, us->iobuf[0]); -- cgit v1.2.3 From 715bfc22ce952a14fac0b9200fd70d81c1951091 Mon Sep 17 00:00:00 2001 From: Anand Gadiyar Date: Tue, 14 Jul 2009 16:41:00 +0530 Subject: USB: OMAP: OHCI: hc_driver's stop method should call ohci_stop OMAP: OHCI: hc_driver's stop method should call ohci_stop Without this, the ohci-omap driver will not cleanup the debugfs nodes when the driver is unloaded. So the next insmod will fail, if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected. Reported-by: vikram pandita Cc: David Brownell Signed-off-by: Anand Gadiyar Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ohci-omap.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index f3aaba35e912..83cbecd2a1ed 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -282,6 +282,7 @@ static int ohci_omap_init(struct usb_hcd *hcd) static void ohci_omap_stop(struct usb_hcd *hcd) { dev_dbg(hcd->self.controller, "stopping USB Controller\n"); + ohci_stop(hcd); omap_ohci_clock_power(0); } -- cgit v1.2.3 From fca4404c55ab44c7413769f1d9c66451103711a5 Mon Sep 17 00:00:00 2001 From: Ville Sundberg Date: Wed, 15 Jul 2009 00:27:28 +0300 Subject: USB: ftdi_sio: Add support for GN Otometrics Aurical USB Audiometer The patch adds support for the GN Otometrics Aurical USB Audiometer (FT232BM-based). A new VID and a new PID is added. Signed-off-by: Ville Sundberg Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 60c64cc5be2a..b574878c78b2 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -698,6 +698,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, + { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index c9fbd7415092..24dbd99e87d7 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -946,6 +946,13 @@ #define FTDI_TURTELIZER_PID 0xBDC8 /* JTAG/RS-232 adapter by egnite GmBH */ +/* + * GN Otometrics (http://www.otometrics.com) + * Submitted by Ville Sundberg. + */ +#define GN_OTOMETRICS_VID 0x0c33 /* Vendor ID */ +#define AURICAL_USB_PID 0x0010 /* Aurical USB Audiometer */ + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- cgit v1.2.3 From 8bf16ba7c8ea9d067914e270764c14020a26232f Mon Sep 17 00:00:00 2001 From: Craig Shelley Date: Sun, 12 Jul 2009 21:52:33 +0100 Subject: USB: CP210x Add new device IDs Signed-off-by: Craig Shelley Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index e9a40b820fd4..985cbcf48bda 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -80,6 +80,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */ { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */ { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */ + { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */ { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */ { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */ { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */ @@ -96,7 +97,9 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(0x10c4, 0x8293) }, /* Telegesys ETRX2USB */ { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */ { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */ + { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */ { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */ + { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */ { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ -- cgit v1.2.3 From bcfa4e68d8d0ea617bde4203b2b3848f5a49a423 Mon Sep 17 00:00:00 2001 From: Simon Kagstrom Date: Mon, 13 Jul 2009 08:25:09 +0200 Subject: USB: ehci-orion: Call ehci_reset before ehci_halt I noticed that USB initialization didn't setup correctly on my kirkwood based board (OpenRD base) if I hadn't initialized USB in U-boot first. The error message looks like this: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: can't setup orion-ehci orion-ehci.0: USB bus 1 deregistered orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110 orion-ehci: probe of orion-ehci.0 failed with error -110 which is caused by ehci_halt() timing out in the handshake() call. I noticed that U-boot does a reset before calling handshake(), so this patch does the same thing for Linux. USB now works for me. Signed-off-by: Simon Kagstrom Acked-by: Nicolas Pitre Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-orion.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-orion.c b/drivers/usb/host/ehci-orion.c index dc2ac613a9d1..1d283e1b2b8d 100644 --- a/drivers/usb/host/ehci-orion.c +++ b/drivers/usb/host/ehci-orion.c @@ -105,6 +105,7 @@ static int ehci_orion_setup(struct usb_hcd *hcd) struct ehci_hcd *ehci = hcd_to_ehci(hcd); int retval; + ehci_reset(ehci); retval = ehci_halt(ehci); if (retval) return retval; @@ -118,7 +119,6 @@ static int ehci_orion_setup(struct usb_hcd *hcd) hcd->has_tt = 1; - ehci_reset(ehci); ehci_port_power(ehci, 0); return retval; -- cgit v1.2.3 From c420befde6b2747ebc2b8f015687a5dbd6e167ca Mon Sep 17 00:00:00 2001 From: Herton Ronaldo Krzesinski Date: Wed, 15 Jul 2009 17:10:26 -0300 Subject: USB: option: add ZTE device ids and remove ONDA ids Current listed Onda ids are ZTE devices. Replace them with ZTE id define and add more ZTE device ids. Also remove 19d2:2000, this is the id when device is first plugged in and is a CD-only device, before the switch using eject. These changes are based on a previous patch by Ming Zhao Signed-off-by: Herton Ronaldo Krzesinski Cc: Ming Zhao Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 113 ++++++++++++++++++++++++++------------------ 1 file changed, 68 insertions(+), 45 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 7638d2632ff8..5640f38fdb3a 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -261,11 +261,6 @@ static int option_resume(struct usb_serial *serial); #define AXESSTEL_VENDOR_ID 0x1726 #define AXESSTEL_PRODUCT_MV110H 0x1000 -#define ONDA_VENDOR_ID 0x19d2 -#define ONDA_PRODUCT_MSA501HS 0x0001 -#define ONDA_PRODUCT_ET502HS 0x0002 -#define ONDA_PRODUCT_MT503HS 0x2000 - #define BANDRICH_VENDOR_ID 0x1A8D #define BANDRICH_PRODUCT_C100_1 0x1002 #define BANDRICH_PRODUCT_C100_2 0x1003 @@ -476,42 +471,6 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) }, { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) }, { USB_DEVICE(AXESSTEL_VENDOR_ID, AXESSTEL_PRODUCT_MV110H) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MSA501HS) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0003) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0004) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0005) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0006) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0007) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0008) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0009) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000a) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000b) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000c) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000d) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000e) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x000f) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0010) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0011) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0012) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0013) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0014) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0015) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0016) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0017) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0018) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0019) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0020) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0021) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0022) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0023) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0024) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0025) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0026) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0027) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0028) }, - { USB_DEVICE(ONDA_VENDOR_ID, 0x0029) }, - { USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MT503HS) }, { USB_DEVICE(YISO_VENDOR_ID, YISO_PRODUCT_U893) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) }, { USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) }, @@ -536,10 +495,74 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */ { USB_DEVICE(MAXON_VENDOR_ID, 0x6280) }, /* BP3-USB & BP3-EXT HSDPA */ { USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628) }, - { USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */ + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0003, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0004, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0005, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0006, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0007, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0008, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0009, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000a, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000b, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000c, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000d, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000e, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000f, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0010, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0011, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0012, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0013, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0016, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0017, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0018, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0019, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0020, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0021, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0022, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0023, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0024, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0025, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0026, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0028, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0029, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0030, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0032, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0033, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0037, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0039, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0042, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0043, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0048, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0049, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0051, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0052, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0054, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0055, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0057, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0058, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0061, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0062, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0063, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0064, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0066, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0069, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0076, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0078, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0082, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0086, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2002, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2003, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0014, 0xff, 0xff, 0xff) }, /* ZTE CDMA products */ + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0027, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0059, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0060, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) }, -- cgit v1.2.3 From f1469fc3ef1d5a8a67146c1c72021f012a59dea6 Mon Sep 17 00:00:00 2001 From: Tim Gardner Date: Fri, 17 Jul 2009 07:55:36 -0600 Subject: USB: option: Add USB ID for Novatel MC727/U727/USB727 refresh BugLink: https://bugs.launchpad.net/bugs/365291 Signed-off-by: Tim Gardner Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 5640f38fdb3a..ff61f89918e4 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -207,6 +207,7 @@ static int option_resume(struct usb_serial *serial); #define NOVATELWIRELESS_PRODUCT_MC727 0x4100 #define NOVATELWIRELESS_PRODUCT_MC950D 0x4400 #define NOVATELWIRELESS_PRODUCT_U727 0x5010 +#define NOVATELWIRELESS_PRODUCT_MC727_NEW 0x5100 #define NOVATELWIRELESS_PRODUCT_MC760 0x6000 #define NOVATELWIRELESS_PRODUCT_OVMC760 0x6002 @@ -435,6 +436,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EU870D) }, /* Novatel EU850D/EU860D/EU870D */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC950D) }, /* Novatel MC930D/MC950D */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727) }, /* Novatel MC727/U727/USB727 */ + { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727_NEW) }, /* Novatel MC727/U727/USB727 refresh */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_U727) }, /* Novatel MC727/U727/USB727 */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC760) }, /* Novatel MC760/U760/USB760 */ { USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_OVMC760) }, /* Novatel Ovation MC760 */ -- cgit v1.2.3 From 9d498beafc0a66ce333f0d9067af0aa5dedd4c8e Mon Sep 17 00:00:00 2001 From: Russell Lang Date: Fri, 17 Jul 2009 19:29:20 +1000 Subject: USB: aten uc2324 is really a moschip 7840 I've opened up the case, and the chips in the ATEN UC2324 are: Moschip MCS7840CV-AA 69507-6B1 0650 (USB to 4-port serial) (logo with AF kerned together) 0748 24BC02 SINGLP (unknown 8-pin chip) (logo looks like 3 or Z in circle) ZT3243LEEA 0752 B7A16420.T (4 chips, so this will be RS232 line driver) (Probably equivalent of Sipex SP3243) So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840, and should use the mos7840.c driver. I expect you will remove the aten2011.c driver from the staging area. From the aten2011.c source code, the device ID for the UC2322 (2 port serial) is 0x7820, just like the Moschip evaluation board. This value should be added to the device id table of mos7840.c. Here's a patch that adds these devices to the driver. From: Russell Lang Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/mos7840.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index c31940a307f8..270009afdf77 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -124,10 +124,13 @@ #define BANDB_DEVICE_ID_USOPTL4_4 0xAC44 #define BANDB_DEVICE_ID_USOPTL4_2 0xAC42 -/* This driver also supports the ATEN UC2324 device since it is mos7840 based - * - if I knew the device id it would also support the ATEN UC2322 */ +/* This driver also supports + * ATEN UC2324 device using Moschip MCS7840 + * ATEN UC2322 device using Moschip MCS7820 + */ #define USB_VENDOR_ID_ATENINTL 0x0557 #define ATENINTL_DEVICE_ID_UC2324 0x2011 +#define ATENINTL_DEVICE_ID_UC2322 0x7820 /* Interrupt Routine Defines */ @@ -177,6 +180,7 @@ static struct usb_device_id moschip_port_id_table[] = { {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)}, {} /* terminating entry */ }; @@ -186,6 +190,7 @@ static __devinitdata struct usb_device_id moschip_id_table_combined[] = { {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)}, {} /* terminating entry */ }; -- cgit v1.2.3 From 183791588efd416fc35a71819683b32dee92615b Mon Sep 17 00:00:00 2001 From: Peng Huang Date: Wed, 22 Jul 2009 11:54:48 +0200 Subject: USB: serial: option: Add ZTE AC8710 usb modem device. Signed-off-by: Peng Huang Cc: Jiri Kosina Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index ff61f89918e4..b6de085bc784 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -299,6 +299,7 @@ static int option_resume(struct usb_serial *serial); #define ZTE_PRODUCT_MF628 0x0015 #define ZTE_PRODUCT_MF626 0x0031 #define ZTE_PRODUCT_CDMA_TECH 0xfffe +#define ZTE_PRODUCT_AC8710 0xfff1 #define BENQ_VENDOR_ID 0x04a5 #define BENQ_PRODUCT_H10 0x4068 @@ -565,6 +566,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) }, { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) }, + { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) }, { USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) }, { USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) }, { USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) }, -- cgit v1.2.3 From 48c348cc939aaa3a07d4938669f2f315152e895e Mon Sep 17 00:00:00 2001 From: Javier Martin Date: Thu, 23 Jul 2009 04:03:43 +0200 Subject: USB: option.c to support Alcatel X060S/X200 broadband modems Added support for the Alcatel X060S/X200 broadband modems to the option driver. The device starts in cd-rom emulation mode (1bbb:f000) and requires the use of the usb_modeswitch tool to switch it to modem mode (1bbb:0000). Signed-off-by: Javier Martin Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index b6de085bc784..c784ddbe7b61 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -321,6 +321,11 @@ static int option_resume(struct usb_serial *serial); #define ALINK_VENDOR_ID 0x1e0e #define ALINK_PRODUCT_3GU 0x9200 +/* ALCATEL PRODUCTS */ +#define ALCATEL_VENDOR_ID 0x1bbb +#define ALCATEL_PRODUCT_X060S 0x0000 + + static struct usb_device_id option_ids[] = { { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) }, { USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) }, @@ -576,6 +581,7 @@ static struct usb_device_id option_ids[] = { { USB_DEVICE(TOSHIBA_VENDOR_ID, TOSHIBA_PRODUCT_HSDPA_MINICARD ) }, /* Toshiba 3G HSDPA == Novatel Expedite EU870D MiniCard */ { USB_DEVICE(ALINK_VENDOR_ID, 0x9000) }, { USB_DEVICE_AND_INTERFACE_INFO(ALINK_VENDOR_ID, ALINK_PRODUCT_3GU, 0xff, 0xff, 0xff) }, + { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X060S) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, option_ids); -- cgit v1.2.3 From f01b017d198486ee3553bee6841f788263cf2c23 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Fri, 17 Jul 2009 17:30:03 +0300 Subject: USB: musb_gadget_ep0: fix typo in service_zero_data_request() This function uses wrong bit mask to prevent clearing RXCSR status bits when halting an endpoint -- which results in clearing SentStall and RxPktRdy bits (that the code actually tries to avoid); must be a result of cut-and-paste... Signed-off-by: Sergei Shtylyov Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_gadget_ep0.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_gadget_ep0.c b/drivers/usb/musb/musb_gadget_ep0.c index 40ed50ecedff..7a6778675ad3 100644 --- a/drivers/usb/musb/musb_gadget_ep0.c +++ b/drivers/usb/musb/musb_gadget_ep0.c @@ -407,7 +407,7 @@ stall: csr |= MUSB_RXCSR_P_SENDSTALL | MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_CLRDATATOG - | MUSB_TXCSR_P_WZC_BITS; + | MUSB_RXCSR_P_WZC_BITS; musb_writew(regs, MUSB_RXCSR, csr); } -- cgit v1.2.3 From 3a9f5bd82dc986d496d8484ff54b107b4515f43f Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Mon, 27 Jul 2009 12:03:19 +0300 Subject: USB: musb: Refer to musb_otg_timer_func under correct #ifdef musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG. Make sure any reference to it is also under the same #ifdef. Without this fix, the driver failes to compile when USB_OTG is defined but USB_MUSB_OTG isn't. Signed-off-by: Amit Kucheria Cc: Felipe Balbi Cc: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 554a414f65d1..642a4e25f7d9 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1990,7 +1990,7 @@ bad_config: if (status < 0) goto fail2; -#ifdef CONFIG_USB_OTG +#ifdef CONFIG_USB_MUSB_OTG setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb); #endif -- cgit v1.2.3 From 2bbff7b742d55b094ed1467702efe146cd60c64f Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Mon, 27 Jul 2009 14:32:15 -0700 Subject: USB: musb: fix CONFIGDATA register read issue INDEX register has to be set to '0' before reading CONFIGDATA register which is only present in TI musb platforms. Currently the default register access mode is set to FLAT_MODE thus INDEX register is not getting set properly with musb_ep_select() which is just a nop operation in FLAT_MODE.This invalid register read is causing module reinset failure. Fixing the issue by moving INDEX register write part to musb_read_configdata() function itself. Signed-off-by: Vikram Pandita Signed-off-by: Anand Gadiyar Signed-off-by: Ajay Kumar Gupta Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/musb/musb_core.c | 1 - drivers/usb/musb/musb_regs.h | 1 + 2 files changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c index 642a4e25f7d9..c7c1ca0494cd 100644 --- a/drivers/usb/musb/musb_core.c +++ b/drivers/usb/musb/musb_core.c @@ -1326,7 +1326,6 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb) int i; /* log core options (read using indexed model) */ - musb_ep_select(mbase, 0); reg = musb_read_configdata(mbase); strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8"); diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h index de3b2f18db44..fbfd3fd9ce1f 100644 --- a/drivers/usb/musb/musb_regs.h +++ b/drivers/usb/musb/musb_regs.h @@ -323,6 +323,7 @@ static inline void musb_write_rxfifoadd(void __iomem *mbase, u16 c_off) static inline u8 musb_read_configdata(void __iomem *mbase) { + musb_writeb(mbase, MUSB_INDEX, 0); return musb_readb(mbase, 0x10 + MUSB_CONFIGDATA); } -- cgit v1.2.3 From 0f157ef3a1284f41d9804ecb87fdcc8ea946b9fa Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 28 Jul 2009 11:56:17 -0400 Subject: USB: usbtest: no need for USB_DEVICEFS THis patch (as1270) allows the usbtest module to be built even when USB_DEVICEFS isn't configured. Tests can be performed without USB_DEVICEFS, using the /dev/bus/usb/*/* device files. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index a68d91a11bee..abe3aa67ed00 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -220,7 +220,7 @@ config USB_IOWARRIOR config USB_TEST tristate "USB testing driver" - depends on USB && USB_DEVICEFS + depends on USB help This driver is for testing host controller software. It is used with specialized device firmware for regression and stress testing, -- cgit v1.2.3 From d8f1a5ed52a81a953918d4aebe185ba008a7be34 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 13 Jul 2009 00:23:47 +0200 Subject: USB: xhci: fix less- and greater than confusion Without this change the loops won't start Signed-off-by: Roel Kluin Cc: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 2501c571f855..56032f2d84e8 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -419,7 +419,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->add_flags, (unsigned long long)dma, ctx->add_flags); dma += field_size; - for (i = 0; i > 6; ++i) { + for (i = 0; i < 6; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", &ctx->rsvd[i], (unsigned long long)dma, ctx->rsvd[i], i); @@ -443,7 +443,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->slot.dev_state, (unsigned long long)dma, ctx->slot.dev_state); dma += field_size; - for (i = 0; i > 4; ++i) { + for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", &ctx->slot.reserved[i], (unsigned long long)dma, ctx->slot.reserved[i], i); -- cgit v1.2.3 From f9dc68fe7ad390428c6bc5d7ff582cdb5d92fcb8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:07 -0700 Subject: USB: xhci: Set TD size in transfer TRB. The 0.95 xHCI specification requires software to set the "TD size" field in each transaction request block (TRB). This field gives the host controller an indication of how much data is remaining in the TD (including the buffer in the current TRB). Set this field in bulk TRBs and data stage TRBs for control transfers. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 20 +++++++++++++++----- 1 file changed, 15 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 02d81985c454..d5b952997423 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1285,6 +1285,7 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* Queue the first TRB, even if it's zero-length */ do { u32 field = 0; + u32 length_field = 0; /* Don't change the cycle bit of the first TRB until later */ if (first_trb) @@ -1314,10 +1315,13 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1), (unsigned int) addr + trb_buff_len); } + length_field = TRB_LEN(trb_buff_len) | + TD_REMAINDER(urb->transfer_buffer_length - running_total) | + TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, (u32) addr, (u32) ((u64) addr >> 32), - TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0), + length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. * (Unless we use event data TRBs, which are a @@ -1365,7 +1369,7 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct xhci_generic_trb *start_trb; bool first_trb; int start_cycle; - u32 field; + u32 field, length_field; int running_total, trb_buff_len, ret; u64 addr; @@ -1443,10 +1447,13 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, td->last_trb = ep_ring->enqueue; field |= TRB_IOC; } + length_field = TRB_LEN(trb_buff_len) | + TD_REMAINDER(urb->transfer_buffer_length - running_total) | + TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, (u32) addr, (u32) ((u64) addr >> 32), - TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0), + length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. * (Unless we use event data TRBs, which are a @@ -1478,7 +1485,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct usb_ctrlrequest *setup; struct xhci_generic_trb *start_trb; int start_cycle; - u32 field; + u32 field, length_field; struct xhci_td *td; ep_ring = xhci->devs[slot_id]->ep_rings[ep_index]; @@ -1528,13 +1535,16 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* If there's data, queue data TRBs */ field = 0; + length_field = TRB_LEN(urb->transfer_buffer_length) | + TD_REMAINDER(urb->transfer_buffer_length) | + TRB_INTR_TARGET(0); if (urb->transfer_buffer_length > 0) { if (setup->bRequestType & USB_DIR_IN) field |= TRB_DIR_IN; queue_trb(xhci, ep_ring, false, lower_32_bits(urb->transfer_dma), upper_32_bits(urb->transfer_dma), - TRB_LEN(urb->transfer_buffer_length) | TRB_INTR_TARGET(0), + length_field, /* Event on short tx */ field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state); } -- cgit v1.2.3 From a1587d97ce3e53816c88b513a2038f6c5e5babd7 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:15 -0700 Subject: USB: xhci: Deal with stalled endpoints. When an endpoint on a device under an xHCI host controller stalls, the host controller driver must let the hardware know that the USB core has successfully cleared the halt condition. The HCD submits a Reset Endpoint Command, which will clear the toggle bit for USB 2.0 devices, and set the sequence number to zero for USB 3.0 devices. The xHCI urb_enqueue will accept new URBs while the endpoint is halted, and will queue them to the hardware rings. However, the endpoint doorbell will not be rung until the Reset Endpoint Command completes. Don't queue a reset endpoint command for root hubs. khubd clears halt conditions on the roothub during the initialization process, but the roothub isn't a real device, so the xHCI host controller doesn't need to know about the cleared halt. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 44 +++++++++++++++++++++++++++++++++++++++++++- drivers/usb/host/xhci-pci.c | 1 + drivers/usb/host/xhci-ring.c | 36 +++++++++++++++++++++++++++++++++++- drivers/usb/host/xhci.h | 8 ++++++-- 4 files changed, 85 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index dba3e07ccd09..1c5901ad6eb8 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -787,8 +787,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, int ret = 0; ret = xhci_check_args(hcd, udev, ep, 1, __func__); - if (ret <= 0) + if (ret <= 0) { + /* So we won't queue a reset ep command for a root hub */ + ep->hcpriv = NULL; return ret; + } xhci = hcd_to_xhci(hcd); added_ctxs = xhci_get_endpoint_flag(&ep->desc); @@ -851,6 +854,9 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } new_slot_info = in_ctx->slot.dev_info; + /* Store the usb_device pointer for later use */ + ep->hcpriv = udev; + xhci_dbg(xhci, "add ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x, new slot info = %#x\n", (unsigned int) ep->desc.bEndpointAddress, udev->slot_id, @@ -1026,6 +1032,42 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) xhci_zero_in_ctx(virt_dev); } +/* Deal with stalled endpoints. The core should have sent the control message + * to clear the halt condition. However, we need to make the xHCI hardware + * reset its sequence number, since a device will expect a sequence number of + * zero after the halt condition is cleared. + * Context: in_interrupt + */ +void xhci_endpoint_reset(struct usb_hcd *hcd, + struct usb_host_endpoint *ep) +{ + struct xhci_hcd *xhci; + struct usb_device *udev; + unsigned int ep_index; + unsigned long flags; + int ret; + + xhci = hcd_to_xhci(hcd); + udev = (struct usb_device *) ep->hcpriv; + /* Called with a root hub endpoint (or an endpoint that wasn't added + * with xhci_add_endpoint() + */ + if (!ep->hcpriv) + return; + ep_index = xhci_get_endpoint_index(&ep->desc); + + xhci_dbg(xhci, "Queueing reset endpoint command\n"); + spin_lock_irqsave(&xhci->lock, flags); + ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index); + if (!ret) { + xhci_ring_cmd_db(xhci); + } + spin_unlock_irqrestore(&xhci->lock, flags); + + if (ret) + xhci_warn(xhci, "FIXME allocate a new ring segment\n"); +} + /* * At this point, the struct usb_device is about to go away, the device has * disconnected, and all traffic has been stopped and the endpoints have been diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 1462709e26c0..592fe7e623f7 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -117,6 +117,7 @@ static const struct hc_driver xhci_pci_hc_driver = { .free_dev = xhci_free_dev, .add_endpoint = xhci_add_endpoint, .drop_endpoint = xhci_drop_endpoint, + .endpoint_reset = xhci_endpoint_reset, .check_bandwidth = xhci_check_bandwidth, .reset_bandwidth = xhci_reset_bandwidth, .address_device = xhci_address_device, diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index d5b952997423..d672ba14ff80 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -279,7 +279,8 @@ static void ring_ep_doorbell(struct xhci_hcd *xhci, /* Don't ring the doorbell for this endpoint if there are pending * cancellations because the we don't want to interrupt processing. */ - if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING)) { + if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING) + && !(ep_ring->state & EP_HALTED)) { field = xhci_readl(xhci, db_addr) & DB_MASK; xhci_writel(xhci, field | EPI_TO_DB(ep_index), db_addr); /* Flush PCI posted writes - FIXME Matthew Wilcox says this @@ -603,6 +604,25 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, ring_ep_doorbell(xhci, slot_id, ep_index); } +static void handle_reset_ep_completion(struct xhci_hcd *xhci, + struct xhci_event_cmd *event, + union xhci_trb *trb) +{ + int slot_id; + unsigned int ep_index; + + slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); + ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); + /* This command will only fail if the endpoint wasn't halted, + * but we don't care. + */ + xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n", + (unsigned int) GET_COMP_CODE(event->status)); + + /* Clear our internal halted state and restart the ring */ + xhci->devs[slot_id]->ep_rings[ep_index]->state &= ~EP_HALTED; + ring_ep_doorbell(xhci, slot_id, ep_index); +} static void handle_cmd_completion(struct xhci_hcd *xhci, struct xhci_event_cmd *event) @@ -653,6 +673,9 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, case TRB_TYPE(TRB_CMD_NOOP): ++xhci->noops_handled; break; + case TRB_TYPE(TRB_RESET_EP): + handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue); + break; default: /* Skip over unknown commands on the event ring */ xhci->error_bitmask |= 1 << 6; @@ -823,6 +846,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, break; case COMP_STALL: xhci_warn(xhci, "WARN: Stalled endpoint\n"); + ep_ring->state |= EP_HALTED; status = -EPIPE; break; case COMP_TRB_ERR: @@ -1656,3 +1680,13 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, return queue_command(xhci, (u32) addr | cycle_state, 0, 0, trb_slot_id | trb_ep_index | type); } + +int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, + unsigned int ep_index) +{ + u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); + u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); + u32 type = TRB_TYPE(TRB_RESET_EP); + + return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type); +} diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 8936eeb5588b..cde648a524f5 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -848,8 +848,8 @@ union xhci_trb { #define TRB_CONFIG_EP 12 /* Evaluate Context Command */ #define TRB_EVAL_CONTEXT 13 -/* Reset Transfer Ring Command */ -#define TRB_RESET_RING 14 +/* Reset Endpoint Command */ +#define TRB_RESET_EP 14 /* Stop Transfer Ring Command */ #define TRB_STOP_RING 15 /* Set Transfer Ring Dequeue Pointer Command */ @@ -929,6 +929,7 @@ struct xhci_ring { unsigned int cancels_pending; unsigned int state; #define SET_DEQ_PENDING (1 << 0) +#define EP_HALTED (1 << 1) /* The TRB that was last reported in a stopped endpoint ring */ union xhci_trb *stopped_trb; struct xhci_td *stopped_td; @@ -1128,6 +1129,7 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags); int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status); int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep); int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep); +void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep); int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); @@ -1148,6 +1150,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb, int slot_id, unsigned int ep_index); int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id); +int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, + unsigned int ep_index); /* xHCI roothub code */ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, -- cgit v1.2.3 From b11069f5f6ce6e359f853e908b0917303fcdec8f Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:23 -0700 Subject: USB: xhci: Use GFP_ATOMIC while holding spinlocks. The xHCI functions to queue an URB onto the hardware rings must be called with the xhci spinlock held. Those functions will allocate memory, and take a gfp_t memory flags argument. We must pass them the GFP_ATOMIC flag, since we don't want the memory allocation to attempt to sleep while waiting for more memory to become available. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 1c5901ad6eb8..ff99365cae42 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -601,10 +601,13 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags) goto exit; } if (usb_endpoint_xfer_control(&urb->ep->desc)) - ret = xhci_queue_ctrl_tx(xhci, mem_flags, urb, + /* We have a spinlock and interrupts disabled, so we must pass + * atomic context to this function, which may allocate memory. + */ + ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); else if (usb_endpoint_xfer_bulk(&urb->ep->desc)) - ret = xhci_queue_bulk_tx(xhci, mem_flags, urb, + ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index); else ret = -EINVAL; -- cgit v1.2.3 From 8e595a5d30a5ee4bb745d4da6439d73ed7d91054 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:31 -0700 Subject: USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 67 +++++++++++++++++--------------------------- drivers/usb/host/xhci-hcd.c | 43 +++++++++++++--------------- drivers/usb/host/xhci-mem.c | 61 ++++++++++++++++------------------------ drivers/usb/host/xhci-ring.c | 49 +++++++++++++++----------------- drivers/usb/host/xhci.h | 65 +++++++++++++++++++++++++++++------------- 5 files changed, 137 insertions(+), 148 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 56032f2d84e8..6d62e4abe3c6 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -173,6 +173,7 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int { void *addr; u32 temp; + u64 temp_64; addr = &ir_set->irq_pending; temp = xhci_readl(xhci, addr); @@ -200,25 +201,15 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int xhci_dbg(xhci, " WARN: %p: ir_set.rsvd = 0x%x\n", addr, (unsigned int)temp); - addr = &ir_set->erst_base[0]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_base[0] = 0x%x\n", - addr, (unsigned int) temp); - - addr = &ir_set->erst_base[1]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_base[1] = 0x%x\n", - addr, (unsigned int) temp); - - addr = &ir_set->erst_dequeue[0]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_dequeue[0] = 0x%x\n", - addr, (unsigned int) temp); + addr = &ir_set->erst_base; + temp_64 = xhci_read_64(xhci, addr); + xhci_dbg(xhci, " %p: ir_set.erst_base = @%08llx\n", + addr, temp_64); - addr = &ir_set->erst_dequeue[1]; - temp = xhci_readl(xhci, addr); - xhci_dbg(xhci, " %p: ir_set.erst_dequeue[1] = 0x%x\n", - addr, (unsigned int) temp); + addr = &ir_set->erst_dequeue; + temp_64 = xhci_read_64(xhci, addr); + xhci_dbg(xhci, " %p: ir_set.erst_dequeue = @%08llx\n", + addr, temp_64); } void xhci_print_run_regs(struct xhci_hcd *xhci) @@ -268,8 +259,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) xhci_dbg(xhci, "Link TRB:\n"); xhci_print_trb_offsets(xhci, trb); - address = trb->link.segment_ptr[0] + - (((u64) trb->link.segment_ptr[1]) << 32); + address = trb->link.segment_ptr; xhci_dbg(xhci, "Next ring segment DMA address = 0x%llx\n", address); xhci_dbg(xhci, "Interrupter target = 0x%x\n", @@ -282,8 +272,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) (unsigned int) (trb->link.control & TRB_NO_SNOOP)); break; case TRB_TYPE(TRB_TRANSFER): - address = trb->trans_event.buffer[0] + - (((u64) trb->trans_event.buffer[1]) << 32); + address = trb->trans_event.buffer; /* * FIXME: look at flags to figure out if it's an address or if * the data is directly in the buffer field. @@ -291,8 +280,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb) xhci_dbg(xhci, "DMA address or buffer contents= %llu\n", address); break; case TRB_TYPE(TRB_COMPLETION): - address = trb->event_cmd.cmd_trb[0] + - (((u64) trb->event_cmd.cmd_trb[1]) << 32); + address = trb->event_cmd.cmd_trb; xhci_dbg(xhci, "Command TRB pointer = %llu\n", address); xhci_dbg(xhci, "Completion status = %u\n", (unsigned int) GET_COMP_CODE(trb->event_cmd.status)); @@ -328,8 +316,8 @@ void xhci_debug_segment(struct xhci_hcd *xhci, struct xhci_segment *seg) for (i = 0; i < TRBS_PER_SEGMENT; ++i) { trb = &seg->trbs[i]; xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", addr, - (unsigned int) trb->link.segment_ptr[0], - (unsigned int) trb->link.segment_ptr[1], + lower_32_bits(trb->link.segment_ptr), + upper_32_bits(trb->link.segment_ptr), (unsigned int) trb->link.intr_target, (unsigned int) trb->link.control); addr += sizeof(*trb); @@ -386,8 +374,8 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst) entry = &erst->entries[i]; xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", (unsigned int) addr, - (unsigned int) entry->seg_addr[0], - (unsigned int) entry->seg_addr[1], + lower_32_bits(entry->seg_addr), + upper_32_bits(entry->seg_addr), (unsigned int) entry->seg_size, (unsigned int) entry->rsvd); addr += sizeof(*entry); @@ -396,12 +384,13 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst) void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) { - u32 val; + u64 val; - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]); - xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = 0x%x\n", val); - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[1]); - xhci_dbg(xhci, "// xHC command ring deq ptr high bits = 0x%x\n", val); + val = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = @%08x\n", + lower_32_bits(val)); + xhci_dbg(xhci, "// xHC command ring deq ptr high bits = @%08x\n", + upper_32_bits(val)); } void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) @@ -462,14 +451,10 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad &ctx->ep[i].ep_info2, (unsigned long long)dma, ctx->ep[i].ep_info2); dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[0]\n", - &ctx->ep[i].deq[0], - (unsigned long long)dma, ctx->ep[i].deq[0]); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[1]\n", - &ctx->ep[i].deq[1], - (unsigned long long)dma, ctx->ep[i].deq[1]); - dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", + &ctx->ep[i].deq, + (unsigned long long)dma, ctx->ep[i].deq); + dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", &ctx->ep[i].tx_info, (unsigned long long)dma, ctx->ep[i].tx_info); diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index ff99365cae42..e15773598e4e 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -226,6 +226,7 @@ int xhci_init(struct usb_hcd *hcd) static void xhci_work(struct xhci_hcd *xhci) { u32 temp; + u64 temp_64; /* * Clear the op reg interrupt status first, @@ -249,8 +250,8 @@ static void xhci_work(struct xhci_hcd *xhci) xhci_handle_event(xhci); /* Clear the event handler busy flag; the event ring should be empty. */ - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - xhci_writel(xhci, temp & ~ERST_EHB, &xhci->ir_set->erst_dequeue[0]); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue); /* Flush posted writes -- FIXME is this necessary? */ xhci_readl(xhci, &xhci->ir_set->irq_pending); } @@ -295,6 +296,7 @@ void xhci_event_ring_work(unsigned long arg) { unsigned long flags; int temp; + u64 temp_64; struct xhci_hcd *xhci = (struct xhci_hcd *) arg; int i, j; @@ -311,9 +313,9 @@ void xhci_event_ring_work(unsigned long arg) xhci_dbg(xhci, "Event ring:\n"); xhci_debug_segment(xhci, xhci->event_ring->deq_seg); xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - temp &= ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 0x%x\n", temp); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); xhci_dbg(xhci, "Command ring:\n"); xhci_debug_segment(xhci, xhci->cmd_ring->deq_seg); xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); @@ -356,6 +358,7 @@ void xhci_event_ring_work(unsigned long arg) int xhci_run(struct usb_hcd *hcd) { u32 temp; + u64 temp_64; struct xhci_hcd *xhci = hcd_to_xhci(hcd); void (*doorbell)(struct xhci_hcd *) = NULL; @@ -416,11 +419,9 @@ int xhci_run(struct usb_hcd *hcd) xhci_dbg(xhci, "Event ring:\n"); xhci_debug_ring(xhci, xhci->event_ring); xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); - temp &= ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 0x%x\n", temp); - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[1]); - xhci_dbg(xhci, "ERST deq upper = 0x%x\n", temp); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); temp = xhci_readl(xhci, &xhci->op_regs->command); temp |= (CMD_RUN); @@ -888,8 +889,7 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) ep_ctx = &virt_dev->in_ctx->ep[i]; ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; - ep_ctx->deq[0] = 0; - ep_ctx->deq[1] = 0; + ep_ctx->deq = 0; ep_ctx->tx_info = 0; } } @@ -1165,7 +1165,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) struct xhci_virt_device *virt_dev; int ret = 0; struct xhci_hcd *xhci = hcd_to_xhci(hcd); - u32 temp; + u64 temp_64; if (!udev->slot_id) { xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id); @@ -1227,18 +1227,13 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) if (ret) { return ret; } - temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[0]); - xhci_dbg(xhci, "Op regs DCBAA ptr[0] = %#08x\n", temp); - temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[1]); - xhci_dbg(xhci, "Op regs DCBAA ptr[1] = %#08x\n", temp); - xhci_dbg(xhci, "Slot ID %d dcbaa entry[0] @%p = %#08x\n", - udev->slot_id, - &xhci->dcbaa->dev_context_ptrs[2*udev->slot_id], - xhci->dcbaa->dev_context_ptrs[2*udev->slot_id]); - xhci_dbg(xhci, "Slot ID %d dcbaa entry[1] @%p = %#08x\n", + temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr); + xhci_dbg(xhci, "Op regs DCBAA ptr = %#016llx\n", temp_64); + xhci_dbg(xhci, "Slot ID %d dcbaa entry @%p = %#016llx\n", udev->slot_id, - &xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1], - xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1]); + &xhci->dcbaa->dev_context_ptrs[udev->slot_id], + (unsigned long long) + xhci->dcbaa->dev_context_ptrs[udev->slot_id]); xhci_dbg(xhci, "Output Context DMA address = %#08llx\n", (unsigned long long)virt_dev->out_ctx_dma); xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index c8a72de1c508..ec825f16dcee 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -88,7 +88,7 @@ static void xhci_link_segments(struct xhci_hcd *xhci, struct xhci_segment *prev, return; prev->next = next; if (link_trbs) { - prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr[0] = next->dma; + prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr = next->dma; /* Set the last TRB in the segment to have a TRB type ID of Link TRB */ val = prev->trbs[TRBS_PER_SEGMENT-1].link.control; @@ -200,8 +200,7 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) return; dev = xhci->devs[slot_id]; - xhci->dcbaa->dev_context_ptrs[2*slot_id] = 0; - xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0; + xhci->dcbaa->dev_context_ptrs[slot_id] = 0; if (!dev) return; @@ -265,13 +264,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, * Point to output device context in dcbaa; skip the output control * context, which is eight 32 bit fields (or 32 bytes long) */ - xhci->dcbaa->dev_context_ptrs[2*slot_id] = + xhci->dcbaa->dev_context_ptrs[slot_id] = (u32) dev->out_ctx_dma + (32); xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, - &xhci->dcbaa->dev_context_ptrs[2*slot_id], + &xhci->dcbaa->dev_context_ptrs[slot_id], (unsigned long long)dev->out_ctx_dma); - xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0; return 1; fail: @@ -360,10 +358,9 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud ep0_ctx->ep_info2 |= MAX_BURST(0); ep0_ctx->ep_info2 |= ERROR_COUNT(3); - ep0_ctx->deq[0] = + ep0_ctx->deq = dev->ep_rings[0]->first_seg->dma; - ep0_ctx->deq[0] |= dev->ep_rings[0]->cycle_state; - ep0_ctx->deq[1] = 0; + ep0_ctx->deq |= dev->ep_rings[0]->cycle_state; /* Steps 7 and 8 were done in xhci_alloc_virt_device() */ @@ -477,8 +474,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, if (!virt_dev->new_ep_rings[ep_index]) return -ENOMEM; ep_ring = virt_dev->new_ep_rings[ep_index]; - ep_ctx->deq[0] = ep_ring->first_seg->dma | ep_ring->cycle_state; - ep_ctx->deq[1] = 0; + ep_ctx->deq = ep_ring->first_seg->dma | ep_ring->cycle_state; ep_ctx->ep_info = xhci_get_endpoint_interval(udev, ep); @@ -535,8 +531,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; - ep_ctx->deq[0] = 0; - ep_ctx->deq[1] = 0; + ep_ctx->deq = 0; ep_ctx->tx_info = 0; /* Don't free the endpoint ring until the set interface or configuration * request succeeds. @@ -551,10 +546,8 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) /* Free the Event Ring Segment Table and the actual Event Ring */ xhci_writel(xhci, 0, &xhci->ir_set->erst_size); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_base); + xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue); size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries); if (xhci->erst.entries) pci_free_consistent(pdev, size, @@ -566,8 +559,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->event_ring = NULL; xhci_dbg(xhci, "Freed event ring\n"); - xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[0]); - xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[1]); + xhci_write_64(xhci, 0, &xhci->op_regs->cmd_ring); if (xhci->cmd_ring) xhci_ring_free(xhci, xhci->cmd_ring); xhci->cmd_ring = NULL; @@ -586,8 +578,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->device_pool = NULL; xhci_dbg(xhci, "Freed device context pool\n"); - xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[0]); - xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[1]); + xhci_write_64(xhci, 0, &xhci->op_regs->dcbaa_ptr); if (xhci->dcbaa) pci_free_consistent(pdev, sizeof(*xhci->dcbaa), xhci->dcbaa, xhci->dcbaa->dma); @@ -602,6 +593,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) dma_addr_t dma; struct device *dev = xhci_to_hcd(xhci)->self.controller; unsigned int val, val2; + u64 val_64; struct xhci_segment *seg; u32 page_size; int i; @@ -647,8 +639,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) xhci->dcbaa->dma = dma; xhci_dbg(xhci, "// Device context base array address = 0x%llx (DMA), %p (virt)\n", (unsigned long long)xhci->dcbaa->dma, xhci->dcbaa); - xhci_writel(xhci, dma, &xhci->op_regs->dcbaa_ptr[0]); - xhci_writel(xhci, (u32) 0, &xhci->op_regs->dcbaa_ptr[1]); + xhci_write_64(xhci, dma, &xhci->op_regs->dcbaa_ptr); /* * Initialize the ring segment pool. The ring must be a contiguous @@ -675,14 +666,12 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) (unsigned long long)xhci->cmd_ring->first_seg->dma); /* Set the address in the Command Ring Control register */ - val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]); - val = (val & ~CMD_RING_ADDR_MASK) | - (xhci->cmd_ring->first_seg->dma & CMD_RING_ADDR_MASK) | + val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) | + (xhci->cmd_ring->first_seg->dma & (u64) ~CMD_RING_RSVD_BITS) | xhci->cmd_ring->cycle_state; - xhci_dbg(xhci, "// Setting command ring address low bits to 0x%x\n", val); - xhci_writel(xhci, val, &xhci->op_regs->cmd_ring[0]); - xhci_dbg(xhci, "// Setting command ring address high bits to 0x0\n"); - xhci_writel(xhci, (u32) 0, &xhci->op_regs->cmd_ring[1]); + xhci_dbg(xhci, "// Setting command ring address to 0x%x\n", val); + xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring); xhci_dbg_cmd_ptrs(xhci); val = xhci_readl(xhci, &xhci->cap_regs->db_off); @@ -722,8 +711,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) /* set ring base address and size for each segment table entry */ for (val = 0, seg = xhci->event_ring->first_seg; val < ERST_NUM_SEGS; val++) { struct xhci_erst_entry *entry = &xhci->erst.entries[val]; - entry->seg_addr[0] = seg->dma; - entry->seg_addr[1] = 0; + entry->seg_addr = seg->dma; entry->seg_size = TRBS_PER_SEGMENT; entry->rsvd = 0; seg = seg->next; @@ -741,11 +729,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) /* set the segment table base address */ xhci_dbg(xhci, "// Set ERST base address for ir_set 0 = 0x%llx\n", (unsigned long long)xhci->erst.erst_dma_addr); - val = xhci_readl(xhci, &xhci->ir_set->erst_base[0]); - val &= ERST_PTR_MASK; - val |= (xhci->erst.erst_dma_addr & ~ERST_PTR_MASK); - xhci_writel(xhci, val, &xhci->ir_set->erst_base[0]); - xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]); + val_64 = xhci_read_64(xhci, &xhci->ir_set->erst_base); + val_64 &= ERST_PTR_MASK; + val_64 |= (xhci->erst.erst_dma_addr & (u64) ~ERST_PTR_MASK); + xhci_write_64(xhci, val_64, &xhci->ir_set->erst_base); /* Set the event ring dequeue address */ xhci_set_hc_event_deq(xhci); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index d672ba14ff80..588686fca471 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -237,7 +237,7 @@ static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, void xhci_set_hc_event_deq(struct xhci_hcd *xhci) { - u32 temp; + u64 temp; dma_addr_t deq; deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, @@ -246,13 +246,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) xhci_warn(xhci, "WARN something wrong with SW event ring " "dequeue ptr.\n"); /* Update HC event ring dequeue pointer */ - temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]); + temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); temp &= ERST_PTR_MASK; if (!in_interrupt()) xhci_dbg(xhci, "// Write event ring dequeue pointer\n"); - xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]); - xhci_writel(xhci, (deq & ~ERST_PTR_MASK) | temp, - &xhci->ir_set->erst_dequeue[0]); + xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, + &xhci->ir_set->erst_dequeue); } /* Ring the host controller doorbell after placing a command on the ring */ @@ -352,7 +351,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ - state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq[0]; + state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq; state->new_deq_ptr = cur_td->last_trb; state->new_deq_seg = find_trb_seg(state->new_deq_seg, @@ -594,10 +593,8 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, * cancelling URBs, which might not be an error... */ } else { - xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq[0] = 0x%x, " - "deq[1] = 0x%x.\n", - dev->out_ctx->ep[ep_index].deq[0], - dev->out_ctx->ep[ep_index].deq[1]); + xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n", + dev->out_ctx->ep[ep_index].deq); } ep_ring->state &= ~SET_DEQ_PENDING; @@ -631,7 +628,7 @@ static void handle_cmd_completion(struct xhci_hcd *xhci, u64 cmd_dma; dma_addr_t cmd_dequeue_dma; - cmd_dma = (((u64) event->cmd_trb[1]) << 32) + event->cmd_trb[0]; + cmd_dma = event->cmd_trb; cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, xhci->cmd_ring->dequeue); /* Is the command ring deq ptr out of sync with the deq seg ptr? */ @@ -794,10 +791,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, return -ENODEV; } - event_dma = event->buffer[0]; - if (event->buffer[1] != 0) - xhci_warn(xhci, "WARN ignoring upper 32-bits of 64-bit TRB dma address\n"); - + event_dma = event->buffer; /* This TRB should be in the TD at the head of this ring's TD list */ if (list_empty(&ep_ring->td_list)) { xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", @@ -821,10 +815,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, event_trb = &event_seg->trbs[(event_dma - event_seg->dma) / sizeof(*event_trb)]; xhci_dbg(xhci, "Event TRB with TRB type ID %u\n", (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10); - xhci_dbg(xhci, "Offset 0x00 (buffer[0]) = 0x%x\n", - (unsigned int) event->buffer[0]); - xhci_dbg(xhci, "Offset 0x04 (buffer[0]) = 0x%x\n", - (unsigned int) event->buffer[1]); + xhci_dbg(xhci, "Offset 0x00 (buffer lo) = 0x%x\n", + lower_32_bits(event->buffer)); + xhci_dbg(xhci, "Offset 0x04 (buffer hi) = 0x%x\n", + upper_32_bits(event->buffer)); xhci_dbg(xhci, "Offset 0x08 (transfer length) = 0x%x\n", (unsigned int) event->transfer_len); xhci_dbg(xhci, "Offset 0x0C (flags) = 0x%x\n", @@ -1343,8 +1337,8 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, TD_REMAINDER(urb->transfer_buffer_length - running_total) | TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, - (u32) addr, - (u32) ((u64) addr >> 32), + lower_32_bits(addr), + upper_32_bits(addr), length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. @@ -1475,8 +1469,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, TD_REMAINDER(urb->transfer_buffer_length - running_total) | TRB_INTR_TARGET(0); queue_trb(xhci, ep_ring, false, - (u32) addr, - (u32) ((u64) addr >> 32), + lower_32_bits(addr), + upper_32_bits(addr), length_field, /* We always want to know if the TRB was short, * or we won't get an event when it completes. @@ -1637,7 +1631,8 @@ int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id) int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id) { - return queue_command(xhci, in_ctx_ptr, 0, 0, + return queue_command(xhci, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id)); } @@ -1645,7 +1640,8 @@ int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id) { - return queue_command(xhci, in_ctx_ptr, 0, 0, + return queue_command(xhci, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id)); } @@ -1677,7 +1673,8 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n"); xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n", deq_seg, deq_ptr); - return queue_command(xhci, (u32) addr | cycle_state, 0, 0, + return queue_command(xhci, lower_32_bits(addr) | cycle_state, + upper_32_bits(addr), 0, trb_slot_id | trb_ep_index | type); } diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index cde648a524f5..60770c89132b 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -25,6 +25,7 @@ #include #include +#include #include "../core/hcd.h" /* Code sharing between pci-quirks and xhci hcd */ @@ -42,14 +43,6 @@ * xHCI register interface. * This corresponds to the eXtensible Host Controller Interface (xHCI) * Revision 0.95 specification - * - * Registers should always be accessed with double word or quad word accesses. - * - * Some xHCI implementations may support 64-bit address pointers. Registers - * with 64-bit address pointers should be written to with dword accesses by - * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. - * xHCI implementations that do not support 64-bit address pointers will ignore - * the high dword, and write order is irrelevant. */ /** @@ -166,10 +159,10 @@ struct xhci_op_regs { u32 reserved1; u32 reserved2; u32 dev_notification; - u32 cmd_ring[2]; + u64 cmd_ring; /* rsvd: offset 0x20-2F */ u32 reserved3[4]; - u32 dcbaa_ptr[2]; + u64 dcbaa_ptr; u32 config_reg; /* rsvd: offset 0x3C-3FF */ u32 reserved4[241]; @@ -254,7 +247,7 @@ struct xhci_op_regs { #define CMD_RING_RUNNING (1 << 3) /* bits 4:5 reserved and should be preserved */ /* Command Ring pointer - bit mask for the lower 32 bits. */ -#define CMD_RING_ADDR_MASK (0xffffffc0) +#define CMD_RING_RSVD_BITS (0x3f) /* CONFIG - Configure Register - config_reg bitmasks */ /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */ @@ -382,8 +375,8 @@ struct xhci_intr_reg { u32 irq_control; u32 erst_size; u32 rsvd; - u32 erst_base[2]; - u32 erst_dequeue[2]; + u64 erst_base; + u64 erst_dequeue; }; /* irq_pending bitmasks */ @@ -538,7 +531,7 @@ struct xhci_slot_ctx { struct xhci_ep_ctx { u32 ep_info; u32 ep_info2; - u32 deq[2]; + u64 deq; u32 tx_info; /* offset 0x14 - 0x1f reserved for HC internal use */ u32 reserved[3]; @@ -641,7 +634,7 @@ struct xhci_virt_device { */ struct xhci_device_context_array { /* 64-bit device addresses; we only write 32-bit addresses */ - u32 dev_context_ptrs[2*MAX_HC_SLOTS]; + u64 dev_context_ptrs[MAX_HC_SLOTS]; /* private xHCD pointers */ dma_addr_t dma; }; @@ -654,7 +647,7 @@ struct xhci_device_context_array { struct xhci_stream_ctx { /* 64-bit stream ring address, cycle state, and stream type */ - u32 stream_ring[2]; + u64 stream_ring; /* offset 0x14 - 0x1f reserved for HC internal use */ u32 reserved[2]; }; @@ -662,7 +655,7 @@ struct xhci_stream_ctx { struct xhci_transfer_event { /* 64-bit buffer address, or immediate data */ - u32 buffer[2]; + u64 buffer; u32 transfer_len; /* This field is interpreted differently based on the type of TRB */ u32 flags; @@ -744,7 +737,7 @@ struct xhci_transfer_event { struct xhci_link_trb { /* 64-bit segment pointer*/ - u32 segment_ptr[2]; + u64 segment_ptr; u32 intr_target; u32 control; }; @@ -755,7 +748,7 @@ struct xhci_link_trb { /* Command completion event TRB */ struct xhci_event_cmd { /* Pointer to command TRB, or the value passed by the event data trb */ - u32 cmd_trb[2]; + u64 cmd_trb; u32 status; u32 flags; }; @@ -943,7 +936,7 @@ struct xhci_ring { struct xhci_erst_entry { /* 64-bit event ring segment address */ - u32 seg_addr[2]; + u64 seg_addr; u32 seg_size; /* Set to zero */ u32 rsvd; @@ -1079,6 +1072,38 @@ static inline void xhci_writel(struct xhci_hcd *xhci, writel(val, regs); } +/* + * Registers should always be accessed with double word or quad word accesses. + * + * Some xHCI implementations may support 64-bit address pointers. Registers + * with 64-bit address pointers should be written to with dword accesses by + * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. + * xHCI implementations that do not support 64-bit address pointers will ignore + * the high dword, and write order is irrelevant. + */ +static inline u64 xhci_read_64(const struct xhci_hcd *xhci, + __u64 __iomem *regs) +{ + __u32 __iomem *ptr = (__u32 __iomem *) regs; + u64 val_lo = readl(ptr); + u64 val_hi = readl(ptr + 1); + return val_lo + (val_hi << 32); +} +static inline void xhci_write_64(struct xhci_hcd *xhci, + const u64 val, __u64 __iomem *regs) +{ + __u32 __iomem *ptr = (__u32 __iomem *) regs; + u32 val_lo = lower_32_bits(val); + u32 val_hi = upper_32_bits(val); + + if (!in_interrupt()) + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", + regs, (long unsigned int) val); + writel(val_lo, ptr); + writel(val_hi, ptr + 1); +} + /* xHCI debugging */ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num); void xhci_print_registers(struct xhci_hcd *xhci); -- cgit v1.2.3 From 62889610f5591005bed9517360e17531684f72d0 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:36 -0700 Subject: USB: xhci: Handle short control packets correctly. When there is a short packet on a control transfer, the xHCI host controller hardware will generate two events. The first event will be for the data stage TD with a completion code for a short packet. The second event will be for the status stage with a successful completion code. Before this patch, the xHCI driver would giveback the short control URB when it received the event for the data stage TD. Then it would become confused when it saw a status stage event for the endpoint for an URB it had already finished processing. Change the xHCI host controller driver to wait for the status stage event when it receives a short transfer completion code for a data stage TD. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 588686fca471..5dd3b1fd71c0 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -892,15 +892,23 @@ static int handle_tx_event(struct xhci_hcd *xhci, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - td->urb->actual_length = - td->urb->transfer_buffer_length; + /* Did we already see a short data stage? */ + if (td->urb->actual_length != 0) + status = -EREMOTEIO; + else + td->urb->actual_length = + td->urb->transfer_buffer_length; } else { /* Maybe the event was for the data stage? */ - if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) + if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) { /* We didn't stop on a link TRB in the middle */ td->urb->actual_length = td->urb->transfer_buffer_length - TRB_LEN(event->transfer_len); + xhci_dbg(xhci, "Waiting for status stage event\n"); + urb = NULL; + goto cleanup; + } } } } else { -- cgit v1.2.3 From 2d83109be62edd9647c45d7ed2b916b03974a7ec Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:40 -0700 Subject: USB: xhci: Correct Event Handler Busy flag usage. The Event Handler Busy bit in the event ring dequeue pointer is write 1 to clear. Fix the interrupt service routine to clear that bit after the event handler has run. xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer without changing any of the four reserved bits in the lower nibble. The event handler busy (EHB) bit is write one to clear, so the new value must always contain a zero in that bit in order to preserve the EHB value. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 4 ++-- drivers/usb/host/xhci-ring.c | 6 +++++- 2 files changed, 7 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index e15773598e4e..2e8e5bf6b6ca 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -249,9 +249,9 @@ static void xhci_work(struct xhci_hcd *xhci) /* FIXME this should be a delayed service routine that clears the EHB */ xhci_handle_event(xhci); - /* Clear the event handler busy flag; the event ring should be empty. */ + /* Clear the event handler busy flag (RW1C); the event ring should be empty. */ temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); - xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue); + xhci_write_64(xhci, temp_64 | ERST_EHB, &xhci->ir_set->erst_dequeue); /* Flush posted writes -- FIXME is this necessary? */ xhci_readl(xhci, &xhci->ir_set->irq_pending); } diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 5dd3b1fd71c0..fe9541a89a3d 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -248,8 +248,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) /* Update HC event ring dequeue pointer */ temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); temp &= ERST_PTR_MASK; + /* Don't clear the EHB bit (which is RW1C) because + * there might be more events to service. + */ + temp &= ~ERST_EHB; if (!in_interrupt()) - xhci_dbg(xhci, "// Write event ring dequeue pointer\n"); + xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, &xhci->ir_set->erst_dequeue); } -- cgit v1.2.3 From 66e49d8774fa03539713e8f91169c37c05df1e94 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:46 -0700 Subject: USB: xhci: Make debugging more verbose. Add more debugging to the irq handler, slot context initialization, ring operations, URB cancellation, and MMIO writes. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 47 +++++++++++++++++++++++++++++++------------- drivers/usb/host/xhci-ring.c | 35 +++++++++++++++++++++++++++++++-- drivers/usb/host/xhci.h | 14 ++++++------- 3 files changed, 72 insertions(+), 24 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 2e8e5bf6b6ca..764995fd59ef 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -267,8 +267,10 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) { struct xhci_hcd *xhci = hcd_to_xhci(hcd); u32 temp, temp2; + union xhci_trb *trb; spin_lock(&xhci->lock); + trb = xhci->event_ring->dequeue; /* Check if the xHC generated the interrupt, or the irq is shared */ temp = xhci_readl(xhci, &xhci->op_regs->status); temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending); @@ -276,6 +278,15 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) spin_unlock(&xhci->lock); return IRQ_NONE; } + xhci_dbg(xhci, "op reg status = %08x\n", temp); + xhci_dbg(xhci, "ir set irq_pending = %08x\n", temp2); + xhci_dbg(xhci, "Event ring dequeue ptr:\n"); + xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n", + (unsigned long long)xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb), + lower_32_bits(trb->link.segment_ptr), + upper_32_bits(trb->link.segment_ptr), + (unsigned int) trb->link.intr_target, + (unsigned int) trb->link.control); if (temp & STS_FATAL) { xhci_warn(xhci, "WARNING: Host System Error\n"); @@ -385,6 +396,20 @@ int xhci_run(struct usb_hcd *hcd) add_timer(&xhci->event_ring_timer); #endif + xhci_dbg(xhci, "Command ring memory map follows:\n"); + xhci_debug_ring(xhci, xhci->cmd_ring); + xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); + xhci_dbg_cmd_ptrs(xhci); + + xhci_dbg(xhci, "ERST memory map follows:\n"); + xhci_dbg_erst(xhci, &xhci->erst); + xhci_dbg(xhci, "Event ring:\n"); + xhci_debug_ring(xhci, xhci->event_ring); + xhci_dbg_ring_ptrs(xhci, xhci->event_ring); + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + temp_64 &= ~ERST_PTR_MASK; + xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); + xhci_dbg(xhci, "// Set the interrupt modulation register\n"); temp = xhci_readl(xhci, &xhci->ir_set->irq_control); temp &= ~ER_IRQ_INTERVAL_MASK; @@ -409,20 +434,6 @@ int xhci_run(struct usb_hcd *hcd) if (NUM_TEST_NOOPS > 0) doorbell = xhci_setup_one_noop(xhci); - xhci_dbg(xhci, "Command ring memory map follows:\n"); - xhci_debug_ring(xhci, xhci->cmd_ring); - xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring); - xhci_dbg_cmd_ptrs(xhci); - - xhci_dbg(xhci, "ERST memory map follows:\n"); - xhci_dbg_erst(xhci, &xhci->erst); - xhci_dbg(xhci, "Event ring:\n"); - xhci_debug_ring(xhci, xhci->event_ring); - xhci_dbg_ring_ptrs(xhci, xhci->event_ring); - temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); - temp_64 &= ~ERST_PTR_MASK; - xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64); - temp = xhci_readl(xhci, &xhci->op_regs->command); temp |= (CMD_RUN); xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n", @@ -665,8 +676,12 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) goto done; xhci_dbg(xhci, "Cancel URB %p\n", urb); + xhci_dbg(xhci, "Event ring:\n"); + xhci_debug_ring(xhci, xhci->event_ring); ep_index = xhci_get_endpoint_index(&urb->ep->desc); ep_ring = xhci->devs[urb->dev->slot_id]->ep_rings[ep_index]; + xhci_dbg(xhci, "Endpoint ring:\n"); + xhci_debug_ring(xhci, ep_ring); td = (struct xhci_td *) urb->hcpriv; ep_ring->cancels_pending++; @@ -1178,6 +1193,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) if (!udev->config) xhci_setup_addressable_virt_dev(xhci, udev); /* Otherwise, assume the core has the device configured how it wants */ + xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); spin_lock_irqsave(&xhci->lock, flags); ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma, @@ -1221,6 +1238,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) default: xhci_err(xhci, "ERROR: unexpected command completion " "code 0x%x.\n", virt_dev->cmd_status); + xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); ret = -EINVAL; break; } diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index fe9541a89a3d..1fc0decfa0ac 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -135,6 +135,7 @@ static void next_trb(struct xhci_hcd *xhci, static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer) { union xhci_trb *next = ++(ring->dequeue); + unsigned long long addr; ring->deq_updates++; /* Update the dequeue pointer further if that was a link TRB or we're at @@ -152,6 +153,13 @@ static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer ring->dequeue = ring->deq_seg->trbs; next = ring->dequeue; } + addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue); + if (ring == xhci->event_ring) + xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr); + else if (ring == xhci->cmd_ring) + xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr); + else + xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr); } /* @@ -171,6 +179,7 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer { u32 chain; union xhci_trb *next; + unsigned long long addr; chain = ring->enqueue->generic.field[3] & TRB_CHAIN; next = ++(ring->enqueue); @@ -204,6 +213,13 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer ring->enqueue = ring->enq_seg->trbs; next = ring->enqueue; } + addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue); + if (ring == xhci->event_ring) + xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr); + else if (ring == xhci->cmd_ring) + xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr); + else + xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr); } /* @@ -252,8 +268,7 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci) * there might be more events to service. */ temp &= ~ERST_EHB; - if (!in_interrupt()) - xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); + xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n"); xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp, &xhci->ir_set->erst_dequeue); } @@ -781,6 +796,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, struct urb *urb = 0; int status = -EINPROGRESS; + xhci_dbg(xhci, "In %s\n", __func__); xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)]; if (!xdev) { xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n"); @@ -789,6 +805,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, /* Endpoint ID is 1 based, our index is zero based */ ep_index = TRB_TO_EP_ID(event->flags) - 1; + xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); ep_ring = xdev->ep_rings[ep_index]; if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n"); @@ -797,6 +814,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, event_dma = event->buffer; /* This TRB should be in the TD at the head of this ring's TD list */ + xhci_dbg(xhci, "%s - checking for list empty\n", __func__); if (list_empty(&ep_ring->td_list)) { xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", TRB_TO_SLOT_ID(event->flags), ep_index); @@ -806,11 +824,14 @@ static int handle_tx_event(struct xhci_hcd *xhci, urb = NULL; goto cleanup; } + xhci_dbg(xhci, "%s - getting list entry\n", __func__); td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list); /* Is this a TRB in the currently executing TD? */ + xhci_dbg(xhci, "%s - looking for TD\n", __func__); event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue, td->last_trb, event_dma); + xhci_dbg(xhci, "%s - found event_seg = %p\n", __func__, event_seg); if (!event_seg) { /* HC is busted, give up! */ xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not part of current TD\n"); @@ -1027,6 +1048,8 @@ cleanup: /* FIXME for multi-TD URBs (who have buffers bigger than 64MB) */ if (urb) { usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb); + xhci_dbg(xhci, "Giveback URB %p, len = %d, status = %d\n", + urb, td->urb->actual_length, status); spin_unlock(&xhci->lock); usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status); spin_lock(&xhci->lock); @@ -1044,6 +1067,7 @@ void xhci_handle_event(struct xhci_hcd *xhci) int update_ptrs = 1; int ret; + xhci_dbg(xhci, "In %s\n", __func__); if (!xhci->event_ring || !xhci->event_ring->dequeue) { xhci->error_bitmask |= 1 << 1; return; @@ -1056,18 +1080,25 @@ void xhci_handle_event(struct xhci_hcd *xhci) xhci->error_bitmask |= 1 << 2; return; } + xhci_dbg(xhci, "%s - OS owns TRB\n", __func__); /* FIXME: Handle more event types. */ switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) { case TRB_TYPE(TRB_COMPLETION): + xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__); handle_cmd_completion(xhci, &event->event_cmd); + xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__); break; case TRB_TYPE(TRB_PORT_STATUS): + xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__); handle_port_status(xhci, event); + xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__); update_ptrs = 0; break; case TRB_TYPE(TRB_TRANSFER): + xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__); ret = handle_tx_event(xhci, &event->trans_event); + xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__); if (ret < 0) xhci->error_bitmask |= 1 << 9; else diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 60770c89132b..074728e10225 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -1065,10 +1065,9 @@ static inline unsigned int xhci_readl(const struct xhci_hcd *xhci, static inline void xhci_writel(struct xhci_hcd *xhci, const unsigned int val, __u32 __iomem *regs) { - if (!in_interrupt()) - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n", - regs, val); + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n", + regs, val); writel(val, regs); } @@ -1096,10 +1095,9 @@ static inline void xhci_write_64(struct xhci_hcd *xhci, u32 val_lo = lower_32_bits(val); u32 val_hi = upper_32_bits(val); - if (!in_interrupt()) - xhci_dbg(xhci, - "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", - regs, (long unsigned int) val); + xhci_dbg(xhci, + "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n", + regs, (long unsigned int) val); writel(val_lo, ptr); writel(val_hi, ptr + 1); } -- cgit v1.2.3 From d3512f63494678dc58e44a20c56278718fd58969 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:03:50 -0700 Subject: USB: xhci: Don't oops if the host doesn't halt. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 764995fd59ef..8c3a074a95cd 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -103,7 +103,10 @@ int xhci_reset(struct xhci_hcd *xhci) u32 state; state = xhci_readl(xhci, &xhci->op_regs->status); - BUG_ON((state & STS_HALT) == 0); + if ((state & STS_HALT) == 0) { + xhci_warn(xhci, "Host controller not halted, aborting reset.\n"); + return 0; + } xhci_dbg(xhci, "// Reset the HC\n"); command = xhci_readl(xhci, &xhci->op_regs->command); -- cgit v1.2.3 From fcf8f576beafb8c5db8aee8a73eb73763fa7b0ad Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:01 -0700 Subject: USB: xhci: Check if the host controller died in IRQ handler. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 8c3a074a95cd..008326d5bc52 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -277,6 +277,9 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) /* Check if the xHC generated the interrupt, or the irq is shared */ temp = xhci_readl(xhci, &xhci->op_regs->status); temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending); + if (temp == 0xffffffff && temp2 == 0xffffffff) + goto hw_died; + if (!(temp & STS_EINT) && !ER_IRQ_PENDING(temp2)) { spin_unlock(&xhci->lock); return IRQ_NONE; @@ -294,6 +297,7 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd) if (temp & STS_FATAL) { xhci_warn(xhci, "WARNING: Host System Error\n"); xhci_halt(xhci); +hw_died: xhci_to_hcd(xhci)->state = HC_STATE_HALT; spin_unlock(&xhci->lock); return -ESHUTDOWN; -- cgit v1.2.3 From 47692d179f7a88794bcd302e53ca7899d7592db9 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:27 -0700 Subject: USB: xhci: Setup HW retries correctly. The xHCI host controller can be programmed to retry a transfer a certain number of times per endpoint before it passes back an error condition to the host controller driver. The xHC will return an error code when the error count transitions from 1 to 0. Programming an error count of 3 means the xHC tries the transfer 3 times, programming it with a 1 means it tries to transfer once, and programming it with 0 means the HW tries the transfer infinitely. We want isochronous transfers to only be tried once, so set the error count to one. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index ec825f16dcee..075e1036bcb4 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -480,11 +480,13 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, /* FIXME dig Mult and streams info out of ep companion desc */ - /* Allow 3 retries for everything but isoc */ + /* Allow 3 retries for everything but isoc; + * error count = 0 means infinite retries. + */ if (!usb_endpoint_xfer_isoc(&ep->desc)) ep_ctx->ep_info2 = ERROR_COUNT(3); else - ep_ctx->ep_info2 = ERROR_COUNT(0); + ep_ctx->ep_info2 = ERROR_COUNT(1); ep_ctx->ep_info2 |= xhci_get_endpoint_type(udev, ep); -- cgit v1.2.3 From 4a73143ced467868e92d7914d9f8bf797640927b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:32 -0700 Subject: USB: xhci: Handle babble errors on transfers. Pass back a babble error when this error code is seen in the transfer event TRB. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-ring.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 1fc0decfa0ac..0903e98989ec 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -876,6 +876,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, xhci_warn(xhci, "WARN: transfer error on endpoint\n"); status = -EPROTO; break; + case COMP_BABBLE: + xhci_warn(xhci, "WARN: babble error on endpoint\n"); + status = -EOVERFLOW; + break; case COMP_DB_ERR: xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n"); status = -ENOSR; -- cgit v1.2.3 From b7d6d99896a6cf38dc354d673afd3fbde10b86c2 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:38 -0700 Subject: USB: xhci: Fail gracefully if there's no SS ep companion descriptor. This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor parsing code. It fails in some corner cases, which means ep->ss_ep_comp may be NULL. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 075e1036bcb4..41aca003ee82 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -496,7 +496,12 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, max_packet = ep->desc.wMaxPacketSize; ep_ctx->ep_info2 |= MAX_PACKET(max_packet); /* dig out max burst from ep companion desc */ - max_packet = ep->ss_ep_comp->desc.bMaxBurst; + if (!ep->ss_ep_comp) { + xhci_warn(xhci, "WARN no SS endpoint companion descriptor.\n"); + max_packet = 0; + } else { + max_packet = ep->ss_ep_comp->desc.bMaxBurst; + } ep_ctx->ep_info2 |= MAX_BURST(max_packet); break; case USB_SPEED_HIGH: -- cgit v1.2.3 From 9f8e443816976edd68f415ea25c0223ea921e88c Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:04:52 -0700 Subject: USB: Fix parsing of SuperSpeed Endpoint Companion descriptor. usb_parse_ss_endpoint_companion() was supposed to allocate a structure to hold the SuperSpeed Endpoint Companion descriptor, and either copy the values the device returned, or fill in default values if the device descriptor did not include the companion descriptor. However, the previous code would miss the last endpoint in a configuration with no descriptors after it. Make usb_parse_endpoint() allocate the SS endpoint companion descriptor and fill it with default values, even if we've run out of buffer space in this configuration descriptor. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/config.c | 48 ++++++++++++++++++++++++++--------------------- 1 file changed, 27 insertions(+), 21 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c index 24dfb33f90cb..a16c538d0132 100644 --- a/drivers/usb/core/config.c +++ b/drivers/usb/core/config.c @@ -80,38 +80,18 @@ static int usb_parse_ss_endpoint_companion(struct device *ddev, int cfgno, int max_tx; int i; - /* Allocate space for the SS endpoint companion descriptor */ - ep->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp), - GFP_KERNEL); - if (!ep->ss_ep_comp) - return -ENOMEM; desc = (struct usb_ss_ep_comp_descriptor *) buffer; if (desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP) { dev_warn(ddev, "No SuperSpeed endpoint companion for config %d " " interface %d altsetting %d ep %d: " "using minimum values\n", cfgno, inum, asnum, ep->desc.bEndpointAddress); - ep->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE; - ep->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP; - ep->ss_ep_comp->desc.bMaxBurst = 0; - /* - * Leave bmAttributes as zero, which will mean no streams for - * bulk, and isoc won't support multiple bursts of packets. - * With bursts of only one packet, and a Mult of 1, the max - * amount of data moved per endpoint service interval is one - * packet. - */ - if (usb_endpoint_xfer_isoc(&ep->desc) || - usb_endpoint_xfer_int(&ep->desc)) - ep->ss_ep_comp->desc.wBytesPerInterval = - ep->desc.wMaxPacketSize; /* * The next descriptor is for an Endpoint or Interface, * no extra descriptors to copy into the companion structure, * and we didn't eat up any of the buffer. */ - retval = 0; - goto valid; + return 0; } memcpy(&ep->ss_ep_comp->desc, desc, USB_DT_SS_EP_COMP_SIZE); desc = &ep->ss_ep_comp->desc; @@ -320,6 +300,28 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum, buffer += i; size -= i; + /* Allocate space for the SS endpoint companion descriptor */ + endpoint->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp), + GFP_KERNEL); + if (!endpoint->ss_ep_comp) + return -ENOMEM; + + /* Fill in some default values (may be overwritten later) */ + endpoint->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE; + endpoint->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP; + endpoint->ss_ep_comp->desc.bMaxBurst = 0; + /* + * Leave bmAttributes as zero, which will mean no streams for + * bulk, and isoc won't support multiple bursts of packets. + * With bursts of only one packet, and a Mult of 1, the max + * amount of data moved per endpoint service interval is one + * packet. + */ + if (usb_endpoint_xfer_isoc(&endpoint->desc) || + usb_endpoint_xfer_int(&endpoint->desc)) + endpoint->ss_ep_comp->desc.wBytesPerInterval = + endpoint->desc.wMaxPacketSize; + if (size > 0) { retval = usb_parse_ss_endpoint_companion(ddev, cfgno, inum, asnum, endpoint, num_ep, buffer, @@ -329,6 +331,10 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum, retval = buffer - buffer0; } } else { + dev_warn(ddev, "config %d interface %d altsetting %d " + "endpoint 0x%X has no " + "SuperSpeed companion descriptor\n", + cfgno, inum, asnum, d->bEndpointAddress); retval = buffer - buffer0; } } else { -- cgit v1.2.3 From 254c80a3a0eb811489f7410c3291f01a60e8e42f Mon Sep 17 00:00:00 2001 From: John Youn Date: Mon, 27 Jul 2009 12:05:03 -0700 Subject: USB: xhci: Scratchpad buffer allocation Allocates and initializes the scratchpad buffer array (XHCI 4.20). This is an array of 64-bit DMA addresses to scratch pages that the controller may use during operation. The number of pages is specified in the "Max Scratchpad Buffers" field of HCSPARAMS2. The DMA address of this array is written into slot 0 of the DCBAA. Signed-off-by: John Youn Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 102 ++++++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/xhci.h | 11 +++++ 2 files changed, 113 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 41aca003ee82..71121d99235d 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -545,6 +545,103 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, */ } +/* Set up the scratchpad buffer array and scratchpad buffers, if needed. */ +static int scratchpad_alloc(struct xhci_hcd *xhci, gfp_t flags) +{ + int i; + struct device *dev = xhci_to_hcd(xhci)->self.controller; + int num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2); + + xhci_dbg(xhci, "Allocating %d scratchpad buffers\n", num_sp); + + if (!num_sp) + return 0; + + xhci->scratchpad = kzalloc(sizeof(*xhci->scratchpad), flags); + if (!xhci->scratchpad) + goto fail_sp; + + xhci->scratchpad->sp_array = + pci_alloc_consistent(to_pci_dev(dev), + num_sp * sizeof(u64), + &xhci->scratchpad->sp_dma); + if (!xhci->scratchpad->sp_array) + goto fail_sp2; + + xhci->scratchpad->sp_buffers = kzalloc(sizeof(void *) * num_sp, flags); + if (!xhci->scratchpad->sp_buffers) + goto fail_sp3; + + xhci->scratchpad->sp_dma_buffers = + kzalloc(sizeof(dma_addr_t) * num_sp, flags); + + if (!xhci->scratchpad->sp_dma_buffers) + goto fail_sp4; + + xhci->dcbaa->dev_context_ptrs[0] = xhci->scratchpad->sp_dma; + for (i = 0; i < num_sp; i++) { + dma_addr_t dma; + void *buf = pci_alloc_consistent(to_pci_dev(dev), + xhci->page_size, &dma); + if (!buf) + goto fail_sp5; + + xhci->scratchpad->sp_array[i] = dma; + xhci->scratchpad->sp_buffers[i] = buf; + xhci->scratchpad->sp_dma_buffers[i] = dma; + } + + return 0; + + fail_sp5: + for (i = i - 1; i >= 0; i--) { + pci_free_consistent(to_pci_dev(dev), xhci->page_size, + xhci->scratchpad->sp_buffers[i], + xhci->scratchpad->sp_dma_buffers[i]); + } + kfree(xhci->scratchpad->sp_dma_buffers); + + fail_sp4: + kfree(xhci->scratchpad->sp_buffers); + + fail_sp3: + pci_free_consistent(to_pci_dev(dev), num_sp * sizeof(u64), + xhci->scratchpad->sp_array, + xhci->scratchpad->sp_dma); + + fail_sp2: + kfree(xhci->scratchpad); + xhci->scratchpad = NULL; + + fail_sp: + return -ENOMEM; +} + +static void scratchpad_free(struct xhci_hcd *xhci) +{ + int num_sp; + int i; + struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + + if (!xhci->scratchpad) + return; + + num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2); + + for (i = 0; i < num_sp; i++) { + pci_free_consistent(pdev, xhci->page_size, + xhci->scratchpad->sp_buffers[i], + xhci->scratchpad->sp_dma_buffers[i]); + } + kfree(xhci->scratchpad->sp_dma_buffers); + kfree(xhci->scratchpad->sp_buffers); + pci_free_consistent(pdev, num_sp * sizeof(u64), + xhci->scratchpad->sp_array, + xhci->scratchpad->sp_dma); + kfree(xhci->scratchpad); + xhci->scratchpad = NULL; +} + void xhci_mem_cleanup(struct xhci_hcd *xhci) { struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); @@ -593,6 +690,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->page_size = 0; xhci->page_shift = 0; + scratchpad_free(xhci); } int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) @@ -755,7 +853,11 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) for (i = 0; i < MAX_HC_SLOTS; ++i) xhci->devs[i] = 0; + if (scratchpad_alloc(xhci, flags)) + goto fail; + return 0; + fail: xhci_warn(xhci, "Couldn't initialize memory\n"); xhci_mem_cleanup(xhci); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 074728e10225..5a09b9a26e0d 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -89,6 +89,7 @@ struct xhci_cap_regs { #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf) /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */ /* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */ +#define HCS_MAX_SCRATCHPAD(p) (((p) >> 27) & 0x1f) /* HCSPARAMS3 - hcs_params3 - bitmasks */ /* bits 0:7, Max U1 to U0 latency for the roothub ports */ @@ -951,6 +952,13 @@ struct xhci_erst { unsigned int erst_size; }; +struct xhci_scratchpad { + u64 *sp_array; + dma_addr_t sp_dma; + void **sp_buffers; + dma_addr_t *sp_dma_buffers; +}; + /* * Each segment table entry is 4*32bits long. 1K seems like an ok size: * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table, @@ -1005,6 +1013,9 @@ struct xhci_hcd { struct xhci_ring *cmd_ring; struct xhci_ring *event_ring; struct xhci_erst erst; + /* Scratchpad */ + struct xhci_scratchpad *scratchpad; + /* slot enabling and address device helpers */ struct completion addr_dev; int slot_id; -- cgit v1.2.3 From 28c2d2efb48dec2f0b050affae6d5787d6449e47 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:05:08 -0700 Subject: USB: xhci: Always align output device contexts to 64 bytes. Make sure the xHCI output device context is 64-byte aligned. Previous code was using the same structure for both the output device context and the input control context. Since the structure had 32 bytes of flags before the device context, the output device context wouldn't be 64-byte aligned. Define a new structure to use for the output device context and clean up the debugging for these two structures. The copy of the device context in the input control context does *not* need to be 64-byte aligned. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 101 +++++++++++++++++++++++++++----------------- drivers/usb/host/xhci-hcd.c | 7 +-- drivers/usb/host/xhci-mem.c | 15 +++---- drivers/usb/host/xhci.h | 19 ++++++++- 4 files changed, 89 insertions(+), 53 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index 6d62e4abe3c6..d77f8de11256 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -393,78 +393,103 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) upper_32_bits(val)); } -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma) { - int i, j; - int last_ep_ctx = 31; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; - - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", - &ctx->drop_flags, (unsigned long long)dma, - ctx->drop_flags); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", - &ctx->add_flags, (unsigned long long)dma, - ctx->add_flags); - dma += field_size; - for (i = 0; i < 6; ++i) { - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->rsvd[i], (unsigned long long)dma, - ctx->rsvd[i], i); - dma += field_size; - } + int i; xhci_dbg(xhci, "Slot Context:\n"); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n", - &ctx->slot.dev_info, - (unsigned long long)dma, ctx->slot.dev_info); + &slot->dev_info, + (unsigned long long)dma, slot->dev_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n", - &ctx->slot.dev_info2, - (unsigned long long)dma, ctx->slot.dev_info2); + &slot->dev_info2, + (unsigned long long)dma, slot->dev_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n", - &ctx->slot.tt_info, - (unsigned long long)dma, ctx->slot.tt_info); + &slot->tt_info, + (unsigned long long)dma, slot->tt_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n", - &ctx->slot.dev_state, - (unsigned long long)dma, ctx->slot.dev_state); + &slot->dev_state, + (unsigned long long)dma, slot->dev_state); dma += field_size; for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->slot.reserved[i], (unsigned long long)dma, - ctx->slot.reserved[i], i); + &slot->reserved[i], (unsigned long long)dma, + slot->reserved[i], i); dma += field_size; } + return dma; +} + +dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep) +{ + int i, j; + int last_ep_ctx = 31; + /* Fields are 32 bits wide, DMA addresses are in bytes */ + int field_size = 32 / 8; + if (last_ep < 31) last_ep_ctx = last_ep + 1; for (i = 0; i < last_ep_ctx; ++i) { xhci_dbg(xhci, "Endpoint %02d Context:\n", i); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n", - &ctx->ep[i].ep_info, - (unsigned long long)dma, ctx->ep[i].ep_info); + &ep[i].ep_info, + (unsigned long long)dma, ep[i].ep_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n", - &ctx->ep[i].ep_info2, - (unsigned long long)dma, ctx->ep[i].ep_info2); + &ep[i].ep_info2, + (unsigned long long)dma, ep[i].ep_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", - &ctx->ep[i].deq, - (unsigned long long)dma, ctx->ep[i].deq); + &ep[i].deq, + (unsigned long long)dma, ep[i].deq); dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", - &ctx->ep[i].tx_info, - (unsigned long long)dma, ctx->ep[i].tx_info); + &ep[i].tx_info, + (unsigned long long)dma, ep[i].tx_info); dma += field_size; for (j = 0; j < 3; ++j) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->ep[i].reserved[j], + &ep[i].reserved[j], (unsigned long long)dma, - ctx->ep[i].reserved[j], j); + ep[i].reserved[j], j); dma += field_size; } } + return dma; +} + +void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +{ + int i; + /* Fields are 32 bits wide, DMA addresses are in bytes */ + int field_size = 32 / 8; + + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", + &ctx->drop_flags, (unsigned long long)dma, + ctx->drop_flags); + dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", + &ctx->add_flags, (unsigned long long)dma, + ctx->add_flags); + dma += field_size; + for (i = 0; i < 6; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", + &ctx->rsvd[i], (unsigned long long)dma, + ctx->rsvd[i], i); + dma += field_size; + } + dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); + dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); +} + +void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep) +{ + dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); + dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); } diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 008326d5bc52..921dd173d793 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -1013,7 +1013,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) } xhci_dbg(xhci, "Output context after successful config ep cmd:\n"); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, + xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); xhci_zero_in_ctx(virt_dev); @@ -1265,7 +1265,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); /* * USB core uses address 1 for the roothubs, so we add one to the * address given back to us by the HC. @@ -1274,9 +1274,6 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) /* Zero the input context control for later use */ virt_dev->in_ctx->add_flags = 0; virt_dev->in_ctx->drop_flags = 0; - /* Mirror flags in the output context for future ep enable/disable */ - virt_dev->out_ctx->add_flags = SLOT_FLAG | EP0_FLAG; - virt_dev->out_ctx->drop_flags = 0; xhci_dbg(xhci, "Device address = %d\n", udev->devnum); /* XXX Meh, not sure if anyone else but choose_address uses this. */ diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 71121d99235d..8d6bdf2f8015 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -235,7 +235,10 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, return 0; dev = xhci->devs[slot_id]; - /* Allocate the (output) device context that will be used in the HC */ + /* Allocate the (output) device context that will be used in the HC. + * The structure is 32 bytes smaller than the input context, but that's + * fine. + */ dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); if (!dev->out_ctx) goto fail; @@ -260,16 +263,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, init_completion(&dev->cmd_completion); - /* - * Point to output device context in dcbaa; skip the output control - * context, which is eight 32 bit fields (or 32 bytes long) - */ - xhci->dcbaa->dev_context_ptrs[slot_id] = - (u32) dev->out_ctx_dma + (32); + /* Point to output device context in dcbaa. */ + xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma; xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, &xhci->dcbaa->dev_context_ptrs[slot_id], - (unsigned long long)dev->out_ctx_dma); + (unsigned long long) xhci->dcbaa->dev_context_ptrs[slot_id]); return 1; fail: diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 5a09b9a26e0d..d4d3c7777fb8 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -584,15 +584,29 @@ struct xhci_ep_ctx { /** * struct xhci_device_control - * Input/Output context; see section 6.2.5. + * Input context; see section 6.2.5. * * @drop_context: set the bit of the endpoint context you want to disable * @add_context: set the bit of the endpoint context you want to enable */ struct xhci_device_control { + /* Input control context */ u32 drop_flags; u32 add_flags; u32 rsvd[6]; + /* Copy of device context */ + struct xhci_slot_ctx slot; + struct xhci_ep_ctx ep[31]; +}; + +/** + * struct xhci_device_ctx + * Device context; see section 6.2.1. + * + * @slot: slot context for the device. + * @ep: array of endpoint contexts for the device. + */ +struct xhci_device_ctx { struct xhci_slot_ctx slot; struct xhci_ep_ctx ep[31]; }; @@ -612,7 +626,7 @@ struct xhci_virt_device { * track of input and output contexts separately because * these commands might fail and we don't trust the hardware. */ - struct xhci_device_control *out_ctx; + struct xhci_device_ctx *out_ctx; dma_addr_t out_ctx_dma; /* Used for addressing devices and configuration changes */ struct xhci_device_control *in_ctx; @@ -1126,6 +1140,7 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst); void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci); void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring); void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep); +void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep); /* xHCI memory managment */ void xhci_mem_cleanup(struct xhci_hcd *xhci); -- cgit v1.2.3 From d115b04818e57bdbc7ccde4d0660b15e33013dc8 Mon Sep 17 00:00:00 2001 From: John Youn Date: Mon, 27 Jul 2009 12:05:15 -0700 Subject: USB: xhci: Support for 64-byte contexts Adds support for controllers that use 64-byte contexts. The following context data structures are affected by this: Device, Input, Input Control, Endpoint, and Slot. To accommodate the use of either 32 or 64-byte contexts, a Device or Input context can only be accessed through functions which look-up and return pointers to their contained contexts. Signed-off-by: John Youn Acked-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-dbg.c | 125 +++++++++++++++++++++++++++---------------- drivers/usb/host/xhci-hcd.c | 121 ++++++++++++++++++++++++----------------- drivers/usb/host/xhci-mem.c | 121 +++++++++++++++++++++++++++++------------ drivers/usb/host/xhci-ring.c | 22 +++++--- drivers/usb/host/xhci.h | 61 +++++++++++---------- 5 files changed, 287 insertions(+), 163 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c index d77f8de11256..705e34324156 100644 --- a/drivers/usb/host/xhci-dbg.c +++ b/drivers/usb/host/xhci-dbg.c @@ -393,103 +393,138 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci) upper_32_bits(val)); } -dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma) +/* Print the last 32 bytes for 64-byte contexts */ +static void dbg_rsvd64(struct xhci_hcd *xhci, u64 *ctx, dma_addr_t dma) +{ + int i; + for (i = 0; i < 4; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx " + "(dma) %#08llx - rsvd64[%d]\n", + &ctx[4 + i], (unsigned long long)dma, + ctx[4 + i], i); + dma += 8; + } +} + +void xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx) { /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; int i; + struct xhci_slot_ctx *slot_ctx = xhci_get_slot_ctx(xhci, ctx); + dma_addr_t dma = ctx->dma + ((unsigned long)slot_ctx - (unsigned long)ctx); + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); + xhci_dbg(xhci, "Slot Context:\n"); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n", - &slot->dev_info, - (unsigned long long)dma, slot->dev_info); + &slot_ctx->dev_info, + (unsigned long long)dma, slot_ctx->dev_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n", - &slot->dev_info2, - (unsigned long long)dma, slot->dev_info2); + &slot_ctx->dev_info2, + (unsigned long long)dma, slot_ctx->dev_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n", - &slot->tt_info, - (unsigned long long)dma, slot->tt_info); + &slot_ctx->tt_info, + (unsigned long long)dma, slot_ctx->tt_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n", - &slot->dev_state, - (unsigned long long)dma, slot->dev_state); + &slot_ctx->dev_state, + (unsigned long long)dma, slot_ctx->dev_state); dma += field_size; for (i = 0; i < 4; ++i) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &slot->reserved[i], (unsigned long long)dma, - slot->reserved[i], i); + &slot_ctx->reserved[i], (unsigned long long)dma, + slot_ctx->reserved[i], i); dma += field_size; } - return dma; + if (csz) + dbg_rsvd64(xhci, (u64 *)slot_ctx, dma); } -dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep) +void xhci_dbg_ep_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int last_ep) { int i, j; int last_ep_ctx = 31; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); if (last_ep < 31) last_ep_ctx = last_ep + 1; for (i = 0; i < last_ep_ctx; ++i) { + struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, ctx, i); + dma_addr_t dma = ctx->dma + + ((unsigned long)ep_ctx - (unsigned long)ctx); + xhci_dbg(xhci, "Endpoint %02d Context:\n", i); xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n", - &ep[i].ep_info, - (unsigned long long)dma, ep[i].ep_info); + &ep_ctx->ep_info, + (unsigned long long)dma, ep_ctx->ep_info); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n", - &ep[i].ep_info2, - (unsigned long long)dma, ep[i].ep_info2); + &ep_ctx->ep_info2, + (unsigned long long)dma, ep_ctx->ep_info2); dma += field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n", - &ep[i].deq, - (unsigned long long)dma, ep[i].deq); + &ep_ctx->deq, + (unsigned long long)dma, ep_ctx->deq); dma += 2*field_size; xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n", - &ep[i].tx_info, - (unsigned long long)dma, ep[i].tx_info); + &ep_ctx->tx_info, + (unsigned long long)dma, ep_ctx->tx_info); dma += field_size; for (j = 0; j < 3; ++j) { xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ep[i].reserved[j], + &ep_ctx->reserved[j], (unsigned long long)dma, - ep[i].reserved[j], j); + ep_ctx->reserved[j], j); dma += field_size; } + + if (csz) + dbg_rsvd64(xhci, (u64 *)ep_ctx, dma); } - return dma; } -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep) +void xhci_dbg_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int last_ep) { int i; /* Fields are 32 bits wide, DMA addresses are in bytes */ int field_size = 32 / 8; - - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", - &ctx->drop_flags, (unsigned long long)dma, - ctx->drop_flags); - dma += field_size; - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", - &ctx->add_flags, (unsigned long long)dma, - ctx->add_flags); - dma += field_size; - for (i = 0; i < 6; ++i) { - xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n", - &ctx->rsvd[i], (unsigned long long)dma, - ctx->rsvd[i], i); + struct xhci_slot_ctx *slot_ctx; + dma_addr_t dma = ctx->dma; + int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params); + + if (ctx->type == XHCI_CTX_TYPE_INPUT) { + struct xhci_input_control_ctx *ctrl_ctx = + xhci_get_input_control_ctx(xhci, ctx); + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n", + &ctrl_ctx->drop_flags, (unsigned long long)dma, + ctrl_ctx->drop_flags); dma += field_size; + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n", + &ctrl_ctx->add_flags, (unsigned long long)dma, + ctrl_ctx->add_flags); + dma += field_size; + for (i = 0; i < 6; ++i) { + xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd2[%d]\n", + &ctrl_ctx->rsvd2[i], (unsigned long long)dma, + ctrl_ctx->rsvd2[i], i); + dma += field_size; + } + + if (csz) + dbg_rsvd64(xhci, (u64 *)ctrl_ctx, dma); } - dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); - dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); -} -void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep) -{ - dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma); - dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep); + slot_ctx = xhci_get_slot_ctx(xhci, ctx); + xhci_dbg_slot_ctx(xhci, ctx); + xhci_dbg_ep_ctx(xhci, ctx, last_ep); } diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 921dd173d793..057a07e876be 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -722,7 +722,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; - struct xhci_device_control *in_ctx; + struct xhci_container_ctx *in_ctx, *out_ctx; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_slot_ctx *slot_ctx; unsigned int last_ctx; unsigned int ep_index; struct xhci_ep_ctx *ep_ctx; @@ -750,31 +752,34 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } in_ctx = xhci->devs[udev->slot_id]->in_ctx; + out_ctx = xhci->devs[udev->slot_id]->out_ctx; + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index); /* If the HC already knows the endpoint is disabled, * or the HCD has noted it is disabled, ignore this request */ if ((ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED || - in_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) { + ctrl_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) { xhci_warn(xhci, "xHCI %s called with disabled ep %p\n", __func__, ep); return 0; } - in_ctx->drop_flags |= drop_flag; - new_drop_flags = in_ctx->drop_flags; + ctrl_ctx->drop_flags |= drop_flag; + new_drop_flags = ctrl_ctx->drop_flags; - in_ctx->add_flags = ~drop_flag; - new_add_flags = in_ctx->add_flags; + ctrl_ctx->add_flags = ~drop_flag; + new_add_flags = ctrl_ctx->add_flags; - last_ctx = xhci_last_valid_endpoint(in_ctx->add_flags); + last_ctx = xhci_last_valid_endpoint(ctrl_ctx->add_flags); + slot_ctx = xhci_get_slot_ctx(xhci, in_ctx); /* Update the last valid endpoint context, if we deleted the last one */ - if ((in_ctx->slot.dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) { - in_ctx->slot.dev_info &= ~LAST_CTX_MASK; - in_ctx->slot.dev_info |= LAST_CTX(last_ctx); + if ((slot_ctx->dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) { + slot_ctx->dev_info &= ~LAST_CTX_MASK; + slot_ctx->dev_info |= LAST_CTX(last_ctx); } - new_slot_info = in_ctx->slot.dev_info; + new_slot_info = slot_ctx->dev_info; xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep); @@ -804,9 +809,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep) { struct xhci_hcd *xhci; - struct xhci_device_control *in_ctx; + struct xhci_container_ctx *in_ctx, *out_ctx; unsigned int ep_index; struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; u32 added_ctxs; unsigned int last_ctx; u32 new_add_flags, new_drop_flags, new_slot_info; @@ -839,12 +846,14 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, } in_ctx = xhci->devs[udev->slot_id]->in_ctx; + out_ctx = xhci->devs[udev->slot_id]->out_ctx; + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index); /* If the HCD has already noted the endpoint is enabled, * ignore this request. */ - if (in_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) { + if (ctrl_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) { xhci_warn(xhci, "xHCI %s called with enabled ep %p\n", __func__, ep); return 0; @@ -862,8 +871,8 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return -ENOMEM; } - in_ctx->add_flags |= added_ctxs; - new_add_flags = in_ctx->add_flags; + ctrl_ctx->add_flags |= added_ctxs; + new_add_flags = ctrl_ctx->add_flags; /* If xhci_endpoint_disable() was called for this endpoint, but the * xHC hasn't been notified yet through the check_bandwidth() call, @@ -871,14 +880,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, * descriptors. We must drop and re-add this endpoint, so we leave the * drop flags alone. */ - new_drop_flags = in_ctx->drop_flags; + new_drop_flags = ctrl_ctx->drop_flags; + slot_ctx = xhci_get_slot_ctx(xhci, in_ctx); /* Update the last valid endpoint context, if we just added one past */ - if ((in_ctx->slot.dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) { - in_ctx->slot.dev_info &= ~LAST_CTX_MASK; - in_ctx->slot.dev_info |= LAST_CTX(last_ctx); + if ((slot_ctx->dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) { + slot_ctx->dev_info &= ~LAST_CTX_MASK; + slot_ctx->dev_info |= LAST_CTX(last_ctx); } - new_slot_info = in_ctx->slot.dev_info; + new_slot_info = slot_ctx->dev_info; /* Store the usb_device pointer for later use */ ep->hcpriv = udev; @@ -892,9 +902,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return 0; } -static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) +static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev) { + struct xhci_input_control_ctx *ctrl_ctx; struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; int i; /* When a device's add flag and drop flag are zero, any subsequent @@ -902,13 +914,15 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev) * untouched. Make sure we don't leave any old state in the input * endpoint contexts. */ - virt_dev->in_ctx->drop_flags = 0; - virt_dev->in_ctx->add_flags = 0; - virt_dev->in_ctx->slot.dev_info &= ~LAST_CTX_MASK; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->drop_flags = 0; + ctrl_ctx->add_flags = 0; + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx); + slot_ctx->dev_info &= ~LAST_CTX_MASK; /* Endpoint 0 is always valid */ - virt_dev->in_ctx->slot.dev_info |= LAST_CTX(1); + slot_ctx->dev_info |= LAST_CTX(1); for (i = 1; i < 31; ++i) { - ep_ctx = &virt_dev->in_ctx->ep[i]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, i); ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; ep_ctx->deq = 0; @@ -934,6 +948,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) unsigned long flags; struct xhci_hcd *xhci; struct xhci_virt_device *virt_dev; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_slot_ctx *slot_ctx; ret = xhci_check_args(hcd, udev, NULL, 0, __func__); if (ret <= 0) @@ -949,16 +965,18 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) virt_dev = xhci->devs[udev->slot_id]; /* See section 4.6.6 - A0 = 1; A1 = D0 = D1 = 0 */ - virt_dev->in_ctx->add_flags |= SLOT_FLAG; - virt_dev->in_ctx->add_flags &= ~EP0_FLAG; - virt_dev->in_ctx->drop_flags &= ~SLOT_FLAG; - virt_dev->in_ctx->drop_flags &= ~EP0_FLAG; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->add_flags |= SLOT_FLAG; + ctrl_ctx->add_flags &= ~EP0_FLAG; + ctrl_ctx->drop_flags &= ~SLOT_FLAG; + ctrl_ctx->drop_flags &= ~EP0_FLAG; xhci_dbg(xhci, "New Input Control Context:\n"); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, - LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, + LAST_CTX_TO_EP_NUM(slot_ctx->dev_info)); spin_lock_irqsave(&xhci->lock, flags); - ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx_dma, + ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx->dma, udev->slot_id); if (ret < 0) { spin_unlock_irqrestore(&xhci->lock, flags); @@ -1013,10 +1031,10 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) } xhci_dbg(xhci, "Output context after successful config ep cmd:\n"); - xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, - LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info)); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, + LAST_CTX_TO_EP_NUM(slot_ctx->dev_info)); - xhci_zero_in_ctx(virt_dev); + xhci_zero_in_ctx(xhci, virt_dev); /* Free any old rings */ for (i = 1; i < 31; ++i) { if (virt_dev->new_ep_rings[i]) { @@ -1054,7 +1072,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) virt_dev->new_ep_rings[i] = NULL; } } - xhci_zero_in_ctx(virt_dev); + xhci_zero_in_ctx(xhci, virt_dev); } /* Deal with stalled endpoints. The core should have sent the control message @@ -1187,6 +1205,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) struct xhci_virt_device *virt_dev; int ret = 0; struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; u64 temp_64; if (!udev->slot_id) { @@ -1201,11 +1221,11 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_setup_addressable_virt_dev(xhci, udev); /* Otherwise, assume the core has the device configured how it wants */ xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2); spin_lock_irqsave(&xhci->lock, flags); - ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma, - udev->slot_id); + ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma, + udev->slot_id); if (ret) { spin_unlock_irqrestore(&xhci->lock, flags); xhci_dbg(xhci, "FIXME: allocate a command ring segment\n"); @@ -1246,7 +1266,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "ERROR: unexpected command completion " "code 0x%x.\n", virt_dev->cmd_status); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2); ret = -EINVAL; break; } @@ -1261,19 +1281,21 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev) (unsigned long long) xhci->dcbaa->dev_context_ptrs[udev->slot_id]); xhci_dbg(xhci, "Output Context DMA address = %#08llx\n", - (unsigned long long)virt_dev->out_ctx_dma); + (unsigned long long)virt_dev->out_ctx->dma); xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id); - xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2); xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id); - xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2); /* * USB core uses address 1 for the roothubs, so we add one to the * address given back to us by the HC. */ - udev->devnum = (virt_dev->out_ctx->slot.dev_state & DEV_ADDR_MASK) + 1; + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx); + udev->devnum = (slot_ctx->dev_state & DEV_ADDR_MASK) + 1; /* Zero the input context control for later use */ - virt_dev->in_ctx->add_flags = 0; - virt_dev->in_ctx->drop_flags = 0; + ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx); + ctrl_ctx->add_flags = 0; + ctrl_ctx->drop_flags = 0; xhci_dbg(xhci, "Device address = %d\n", udev->devnum); /* XXX Meh, not sure if anyone else but choose_address uses this. */ @@ -1315,7 +1337,6 @@ static int __init xhci_hcd_init(void) /* xhci_device_control has eight fields, and also * embeds one xhci_slot_ctx and 31 xhci_ep_ctx */ - BUILD_BUG_ON(sizeof(struct xhci_device_control) != (8+8+8*31)*32/8); BUILD_BUG_ON(sizeof(struct xhci_stream_ctx) != 4*32/8); BUILD_BUG_ON(sizeof(union xhci_trb) != 4*32/8); BUILD_BUG_ON(sizeof(struct xhci_erst_entry) != 4*32/8); diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 8d6bdf2f8015..e6b9a1c6002d 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -189,6 +189,63 @@ fail: return 0; } +#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32) + +struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci, + int type, gfp_t flags) +{ + struct xhci_container_ctx *ctx = kzalloc(sizeof(*ctx), flags); + if (!ctx) + return NULL; + + BUG_ON((type != XHCI_CTX_TYPE_DEVICE) && (type != XHCI_CTX_TYPE_INPUT)); + ctx->type = type; + ctx->size = HCC_64BYTE_CONTEXT(xhci->hcc_params) ? 2048 : 1024; + if (type == XHCI_CTX_TYPE_INPUT) + ctx->size += CTX_SIZE(xhci->hcc_params); + + ctx->bytes = dma_pool_alloc(xhci->device_pool, flags, &ctx->dma); + memset(ctx->bytes, 0, ctx->size); + return ctx; +} + +void xhci_free_container_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + dma_pool_free(xhci->device_pool, ctx->bytes, ctx->dma); + kfree(ctx); +} + +struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + BUG_ON(ctx->type != XHCI_CTX_TYPE_INPUT); + return (struct xhci_input_control_ctx *)ctx->bytes; +} + +struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx) +{ + if (ctx->type == XHCI_CTX_TYPE_DEVICE) + return (struct xhci_slot_ctx *)ctx->bytes; + + return (struct xhci_slot_ctx *) + (ctx->bytes + CTX_SIZE(xhci->hcc_params)); +} + +struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, + struct xhci_container_ctx *ctx, + unsigned int ep_index) +{ + /* increment ep index by offset of start of ep ctx array */ + ep_index++; + if (ctx->type == XHCI_CTX_TYPE_INPUT) + ep_index++; + + return (struct xhci_ep_ctx *) + (ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params))); +} + /* All the xhci_tds in the ring's TD list should be freed at this point */ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) { @@ -209,11 +266,10 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) xhci_ring_free(xhci, dev->ep_rings[i]); if (dev->in_ctx) - dma_pool_free(xhci->device_pool, - dev->in_ctx, dev->in_ctx_dma); + xhci_free_container_ctx(xhci, dev->in_ctx); if (dev->out_ctx) - dma_pool_free(xhci->device_pool, - dev->out_ctx, dev->out_ctx_dma); + xhci_free_container_ctx(xhci, dev->out_ctx); + kfree(xhci->devs[slot_id]); xhci->devs[slot_id] = 0; } @@ -221,7 +277,6 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id) int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, struct usb_device *udev, gfp_t flags) { - dma_addr_t dma; struct xhci_virt_device *dev; /* Slot ID 0 is reserved */ @@ -235,26 +290,21 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, return 0; dev = xhci->devs[slot_id]; - /* Allocate the (output) device context that will be used in the HC. - * The structure is 32 bytes smaller than the input context, but that's - * fine. - */ - dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); + /* Allocate the (output) device context that will be used in the HC. */ + dev->out_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_DEVICE, flags); if (!dev->out_ctx) goto fail; - dev->out_ctx_dma = dma; + xhci_dbg(xhci, "Slot %d output ctx = 0x%llx (dma)\n", slot_id, - (unsigned long long)dma); - memset(dev->out_ctx, 0, sizeof(*dev->out_ctx)); + (unsigned long long)dev->out_ctx->dma); /* Allocate the (input) device context for address device command */ - dev->in_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma); + dev->in_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_INPUT, flags); if (!dev->in_ctx) goto fail; - dev->in_ctx_dma = dma; + xhci_dbg(xhci, "Slot %d input ctx = 0x%llx (dma)\n", slot_id, - (unsigned long long)dma); - memset(dev->in_ctx, 0, sizeof(*dev->in_ctx)); + (unsigned long long)dev->in_ctx->dma); /* Allocate endpoint 0 ring */ dev->ep_rings[0] = xhci_ring_alloc(xhci, 1, true, flags); @@ -264,7 +314,7 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, init_completion(&dev->cmd_completion); /* Point to output device context in dcbaa. */ - xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma; + xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx->dma; xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n", slot_id, &xhci->dcbaa->dev_context_ptrs[slot_id], @@ -282,6 +332,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud struct xhci_virt_device *dev; struct xhci_ep_ctx *ep0_ctx; struct usb_device *top_dev; + struct xhci_slot_ctx *slot_ctx; + struct xhci_input_control_ctx *ctrl_ctx; dev = xhci->devs[udev->slot_id]; /* Slot ID 0 is reserved */ @@ -290,27 +342,29 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud udev->slot_id); return -EINVAL; } - ep0_ctx = &dev->in_ctx->ep[0]; + ep0_ctx = xhci_get_ep_ctx(xhci, dev->in_ctx, 0); + ctrl_ctx = xhci_get_input_control_ctx(xhci, dev->in_ctx); + slot_ctx = xhci_get_slot_ctx(xhci, dev->in_ctx); /* 2) New slot context and endpoint 0 context are valid*/ - dev->in_ctx->add_flags = SLOT_FLAG | EP0_FLAG; + ctrl_ctx->add_flags = SLOT_FLAG | EP0_FLAG; /* 3) Only the control endpoint is valid - one endpoint context */ - dev->in_ctx->slot.dev_info |= LAST_CTX(1); + slot_ctx->dev_info |= LAST_CTX(1); switch (udev->speed) { case USB_SPEED_SUPER: - dev->in_ctx->slot.dev_info |= (u32) udev->route; - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_SS; + slot_ctx->dev_info |= (u32) udev->route; + slot_ctx->dev_info |= (u32) SLOT_SPEED_SS; break; case USB_SPEED_HIGH: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_HS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_HS; break; case USB_SPEED_FULL: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_FS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_FS; break; case USB_SPEED_LOW: - dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_LS; + slot_ctx->dev_info |= (u32) SLOT_SPEED_LS; break; case USB_SPEED_VARIABLE: xhci_dbg(xhci, "FIXME xHCI doesn't support wireless speeds\n"); @@ -324,7 +378,7 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud for (top_dev = udev; top_dev->parent && top_dev->parent->parent; top_dev = top_dev->parent) /* Found device below root hub */; - dev->in_ctx->slot.dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum); + slot_ctx->dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum); xhci_dbg(xhci, "Set root hub portnum to %d\n", top_dev->portnum); /* Is this a LS/FS device under a HS hub? */ @@ -334,8 +388,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud */ if ((udev->speed == USB_SPEED_LOW || udev->speed == USB_SPEED_FULL) && udev->tt) { - dev->in_ctx->slot.tt_info = udev->tt->hub->slot_id; - dev->in_ctx->slot.tt_info |= udev->ttport << 8; + slot_ctx->tt_info = udev->tt->hub->slot_id; + slot_ctx->tt_info |= udev->ttport << 8; } xhci_dbg(xhci, "udev->tt = %p\n", udev->tt); xhci_dbg(xhci, "udev->ttport = 0x%x\n", udev->ttport); @@ -466,7 +520,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, unsigned int max_burst; ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &virt_dev->in_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index); /* Set up the endpoint ring */ virt_dev->new_ep_rings[ep_index] = xhci_ring_alloc(xhci, 1, true, mem_flags); @@ -533,7 +587,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep_ctx; ep_index = xhci_get_endpoint_index(&ep->desc); - ep_ctx = &virt_dev->in_ctx->ep[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index); ep_ctx->ep_info = 0; ep_ctx->ep_info2 = 0; @@ -753,11 +807,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) */ xhci->segment_pool = dma_pool_create("xHCI ring segments", dev, SEGMENT_SIZE, 64, xhci->page_size); + /* See Table 46 and Note on Figure 55 */ - /* FIXME support 64-byte contexts */ xhci->device_pool = dma_pool_create("xHCI input/output contexts", dev, - sizeof(struct xhci_device_control), - 64, xhci->page_size); + 2112, 64, xhci->page_size); if (!xhci->segment_pool || !xhci->device_pool) goto fail; diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 0903e98989ec..ea31753c3137 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -362,6 +362,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, struct xhci_virt_device *dev = xhci->devs[slot_id]; struct xhci_ring *ep_ring = dev->ep_rings[ep_index]; struct xhci_generic_trb *trb; + struct xhci_ep_ctx *ep_ctx; state->new_cycle_state = 0; state->new_deq_seg = find_trb_seg(cur_td->start_seg, @@ -370,7 +371,8 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ - state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq; + ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); + state->new_cycle_state = 0x1 & ep_ctx->deq; state->new_deq_ptr = cur_td->last_trb; state->new_deq_seg = find_trb_seg(state->new_deq_seg, @@ -570,11 +572,15 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, unsigned int ep_index; struct xhci_ring *ep_ring; struct xhci_virt_device *dev; + struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]); ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]); dev = xhci->devs[slot_id]; ep_ring = dev->ep_rings[ep_index]; + ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); + slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx); if (GET_COMP_CODE(event->status) != COMP_SUCCESS) { unsigned int ep_state; @@ -588,9 +594,9 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, case COMP_CTX_STATE: xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due " "to incorrect slot or ep state.\n"); - ep_state = dev->out_ctx->ep[ep_index].ep_info; + ep_state = ep_ctx->ep_info; ep_state &= EP_STATE_MASK; - slot_state = dev->out_ctx->slot.dev_state; + slot_state = slot_ctx->dev_state; slot_state = GET_SLOT_STATE(slot_state); xhci_dbg(xhci, "Slot state = %u, EP state = %u\n", slot_state, ep_state); @@ -613,7 +619,7 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci, */ } else { xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n", - dev->out_ctx->ep[ep_index].deq); + ep_ctx->deq); } ep_ring->state &= ~SET_DEQ_PENDING; @@ -795,6 +801,7 @@ static int handle_tx_event(struct xhci_hcd *xhci, union xhci_trb *event_trb; struct urb *urb = 0; int status = -EINPROGRESS; + struct xhci_ep_ctx *ep_ctx; xhci_dbg(xhci, "In %s\n", __func__); xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)]; @@ -807,7 +814,8 @@ static int handle_tx_event(struct xhci_hcd *xhci, ep_index = TRB_TO_EP_ID(event->flags) - 1; xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index); ep_ring = xdev->ep_rings[ep_index]; - if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { + ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); + if (!ep_ring || (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) { xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n"); return -ENODEV; } @@ -1193,9 +1201,9 @@ static int prepare_transfer(struct xhci_hcd *xhci, gfp_t mem_flags) { int ret; - + struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); ret = prepare_ring(xhci, xdev->ep_rings[ep_index], - xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK, + ep_ctx->ep_info & EP_STATE_MASK, num_trbs, mem_flags); if (ret) return ret; diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index d4d3c7777fb8..9c108c632704 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -446,6 +446,27 @@ struct xhci_doorbell_array { #define EPI_TO_DB(p) (((p) + 1) & 0xff) +/** + * struct xhci_container_ctx + * @type: Type of context. Used to calculated offsets to contained contexts. + * @size: Size of the context data + * @bytes: The raw context data given to HW + * @dma: dma address of the bytes + * + * Represents either a Device or Input context. Holds a pointer to the raw + * memory used for the context (bytes) and dma address of it (dma). + */ +struct xhci_container_ctx { + unsigned type; +#define XHCI_CTX_TYPE_DEVICE 0x1 +#define XHCI_CTX_TYPE_INPUT 0x2 + + int size; + + u8 *bytes; + dma_addr_t dma; +}; + /** * struct xhci_slot_ctx * @dev_info: Route string, device speed, hub info, and last valid endpoint @@ -583,32 +604,16 @@ struct xhci_ep_ctx { /** - * struct xhci_device_control - * Input context; see section 6.2.5. + * struct xhci_input_control_context + * Input control context; see section 6.2.5. * * @drop_context: set the bit of the endpoint context you want to disable * @add_context: set the bit of the endpoint context you want to enable */ -struct xhci_device_control { - /* Input control context */ +struct xhci_input_control_ctx { u32 drop_flags; u32 add_flags; - u32 rsvd[6]; - /* Copy of device context */ - struct xhci_slot_ctx slot; - struct xhci_ep_ctx ep[31]; -}; - -/** - * struct xhci_device_ctx - * Device context; see section 6.2.1. - * - * @slot: slot context for the device. - * @ep: array of endpoint contexts for the device. - */ -struct xhci_device_ctx { - struct xhci_slot_ctx slot; - struct xhci_ep_ctx ep[31]; + u32 rsvd2[6]; }; /* drop context bitmasks */ @@ -616,7 +621,6 @@ struct xhci_device_ctx { /* add context bitmasks */ #define ADD_EP(x) (0x1 << x) - struct xhci_virt_device { /* * Commands to the hardware are passed an "input context" that @@ -626,11 +630,10 @@ struct xhci_virt_device { * track of input and output contexts separately because * these commands might fail and we don't trust the hardware. */ - struct xhci_device_ctx *out_ctx; - dma_addr_t out_ctx_dma; + struct xhci_container_ctx *out_ctx; /* Used for addressing devices and configuration changes */ - struct xhci_device_control *in_ctx; - dma_addr_t in_ctx_dma; + struct xhci_container_ctx *in_ctx; + /* FIXME when stream support is added */ struct xhci_ring *ep_rings[31]; /* Temporary storage in case the configure endpoint command fails and we @@ -1139,8 +1142,7 @@ void xhci_debug_ring(struct xhci_hcd *xhci, struct xhci_ring *ring); void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst); void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci); void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring); -void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep); -void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep); +void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int last_ep); /* xHCI memory managment */ void xhci_mem_cleanup(struct xhci_hcd *xhci); @@ -1207,4 +1209,9 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength); int xhci_hub_status_data(struct usb_hcd *hcd, char *buf); +/* xHCI contexts */ +struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); +struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); +struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index); + #endif /* __LINUX_XHCI_HCD_H */ -- cgit v1.2.3 From c92bcfa7b4038d8ffe1f02e21269f18eb0b64144 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Mon, 27 Jul 2009 12:05:21 -0700 Subject: USB: xhci: Stall handling bug fixes. Correct the xHCI code to handle stalls on USB endpoints. We need to move the endpoint ring's dequeue pointer past the stalled transfer, or the HW will try to restart the transfer the next time the doorbell is rung. Don't attempt to clear a halt on an endpoint if we haven't seen a stalled transfer for it. The USB core will attempt to clear a halt on all endpoints when it selects a new configuration. Signed-off-by: Sarah Sharp Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-hcd.c | 24 ++++++++ drivers/usb/host/xhci-ring.c | 133 +++++++++++++++++++++++++++---------------- drivers/usb/host/xhci.h | 12 ++++ 3 files changed, 120 insertions(+), 49 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c index 057a07e876be..816c39caca1c 100644 --- a/drivers/usb/host/xhci-hcd.c +++ b/drivers/usb/host/xhci-hcd.c @@ -1089,6 +1089,8 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, unsigned int ep_index; unsigned long flags; int ret; + struct xhci_dequeue_state deq_state; + struct xhci_ring *ep_ring; xhci = hcd_to_xhci(hcd); udev = (struct usb_device *) ep->hcpriv; @@ -1098,11 +1100,33 @@ void xhci_endpoint_reset(struct usb_hcd *hcd, if (!ep->hcpriv) return; ep_index = xhci_get_endpoint_index(&ep->desc); + ep_ring = xhci->devs[udev->slot_id]->ep_rings[ep_index]; + if (!ep_ring->stopped_td) { + xhci_dbg(xhci, "Endpoint 0x%x not halted, refusing to reset.\n", + ep->desc.bEndpointAddress); + return; + } xhci_dbg(xhci, "Queueing reset endpoint command\n"); spin_lock_irqsave(&xhci->lock, flags); ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index); + /* + * Can't change the ring dequeue pointer until it's transitioned to the + * stopped state, which is only upon a successful reset endpoint + * command. Better hope that last command worked! + */ if (!ret) { + xhci_dbg(xhci, "Cleaning up stalled endpoint ring\n"); + /* We need to move the HW's dequeue pointer past this TD, + * or it will attempt to resend it on the next doorbell ring. + */ + xhci_find_new_dequeue_state(xhci, udev->slot_id, + ep_index, ep_ring->stopped_td, &deq_state); + xhci_dbg(xhci, "Queueing new dequeue state\n"); + xhci_queue_new_dequeue_state(xhci, ep_ring, + udev->slot_id, + ep_index, &deq_state); + kfree(ep_ring->stopped_td); xhci_ring_cmd_db(xhci); } spin_unlock_irqrestore(&xhci->lock, flags); diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index ea31753c3137..aa88a067148b 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -335,12 +335,6 @@ static struct xhci_segment *find_trb_seg( return cur_seg; } -struct dequeue_state { - struct xhci_segment *new_deq_seg; - union xhci_trb *new_deq_ptr; - int new_cycle_state; -}; - /* * Move the xHC's endpoint ring dequeue pointer past cur_td. * Record the new state of the xHC's endpoint ring dequeue segment, @@ -355,26 +349,30 @@ struct dequeue_state { * - Finally we move the dequeue state one TRB further, toggling the cycle bit * if we've moved it past a link TRB with the toggle cycle bit set. */ -static void find_new_dequeue_state(struct xhci_hcd *xhci, +void xhci_find_new_dequeue_state(struct xhci_hcd *xhci, unsigned int slot_id, unsigned int ep_index, - struct xhci_td *cur_td, struct dequeue_state *state) + struct xhci_td *cur_td, struct xhci_dequeue_state *state) { struct xhci_virt_device *dev = xhci->devs[slot_id]; struct xhci_ring *ep_ring = dev->ep_rings[ep_index]; struct xhci_generic_trb *trb; struct xhci_ep_ctx *ep_ctx; + dma_addr_t addr; state->new_cycle_state = 0; + xhci_dbg(xhci, "Finding segment containing stopped TRB.\n"); state->new_deq_seg = find_trb_seg(cur_td->start_seg, ep_ring->stopped_trb, &state->new_cycle_state); if (!state->new_deq_seg) BUG(); /* Dig out the cycle state saved by the xHC during the stop ep cmd */ + xhci_dbg(xhci, "Finding endpoint context\n"); ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index); state->new_cycle_state = 0x1 & ep_ctx->deq; state->new_deq_ptr = cur_td->last_trb; + xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n"); state->new_deq_seg = find_trb_seg(state->new_deq_seg, state->new_deq_ptr, &state->new_cycle_state); @@ -388,6 +386,12 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci, next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr); /* Don't update the ring cycle state for the producer (us). */ + xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n", + state->new_deq_seg); + addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr); + xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n", + (unsigned long long) addr); + xhci_dbg(xhci, "Setting dequeue pointer in internal ring state.\n"); ep_ring->dequeue = state->new_deq_ptr; ep_ring->deq_seg = state->new_deq_seg; } @@ -437,6 +441,30 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index, struct xhci_segment *deq_seg, union xhci_trb *deq_ptr, u32 cycle_state); +void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci, + struct xhci_ring *ep_ring, unsigned int slot_id, + unsigned int ep_index, struct xhci_dequeue_state *deq_state) +{ + xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), " + "new deq ptr = %p (0x%llx dma), new cycle = %u\n", + deq_state->new_deq_seg, + (unsigned long long)deq_state->new_deq_seg->dma, + deq_state->new_deq_ptr, + (unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr), + deq_state->new_cycle_state); + queue_set_tr_deq(xhci, slot_id, ep_index, + deq_state->new_deq_seg, + deq_state->new_deq_ptr, + (u32) deq_state->new_cycle_state); + /* Stop the TD queueing code from ringing the doorbell until + * this command completes. The HC won't set the dequeue pointer + * if the ring is running, and ringing the doorbell starts the + * ring running. + */ + ep_ring->state |= SET_DEQ_PENDING; + xhci_ring_cmd_db(xhci); +} + /* * When we get a command completion for a Stop Endpoint Command, we need to * unlink any cancelled TDs from the ring. There are two ways to do that: @@ -457,7 +485,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, struct xhci_td *cur_td = 0; struct xhci_td *last_unlinked_td; - struct dequeue_state deq_state; + struct xhci_dequeue_state deq_state; #ifdef CONFIG_USB_HCD_STAT ktime_t stop_time = ktime_get(); #endif @@ -485,7 +513,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, * move the xHC endpoint ring dequeue pointer past this TD. */ if (cur_td == ep_ring->stopped_td) - find_new_dequeue_state(xhci, slot_id, ep_index, cur_td, + xhci_find_new_dequeue_state(xhci, slot_id, ep_index, cur_td, &deq_state); else td_to_noop(xhci, ep_ring, cur_td); @@ -501,24 +529,8 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci, /* If necessary, queue a Set Transfer Ring Dequeue Pointer command */ if (deq_state.new_deq_ptr && deq_state.new_deq_seg) { - xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), " - "new deq ptr = %p (0x%llx dma), new cycle = %u\n", - deq_state.new_deq_seg, - (unsigned long long)deq_state.new_deq_seg->dma, - deq_state.new_deq_ptr, - (unsigned long long)xhci_trb_virt_to_dma(deq_state.new_deq_seg, deq_state.new_deq_ptr), - deq_state.new_cycle_state); - queue_set_tr_deq(xhci, slot_id, ep_index, - deq_state.new_deq_seg, - deq_state.new_deq_ptr, - (u32) deq_state.new_cycle_state); - /* Stop the TD queueing code from ringing the doorbell until - * this command completes. The HC won't set the dequeue pointer - * if the ring is running, and ringing the doorbell starts the - * ring running. - */ - ep_ring->state |= SET_DEQ_PENDING; - xhci_ring_cmd_db(xhci); + xhci_queue_new_dequeue_state(xhci, ep_ring, + slot_id, ep_index, &deq_state); } else { /* Otherwise just ring the doorbell to restart the ring */ ring_ep_doorbell(xhci, slot_id, ep_index); @@ -929,12 +941,15 @@ static int handle_tx_event(struct xhci_hcd *xhci, if (event_trb != ep_ring->dequeue) { /* The event was for the status stage */ if (event_trb == td->last_trb) { - /* Did we already see a short data stage? */ - if (td->urb->actual_length != 0) - status = -EREMOTEIO; - else + if (td->urb->actual_length != 0) { + /* Don't overwrite a previously set error code */ + if (status == -EINPROGRESS || status == 0) + /* Did we already see a short data stage? */ + status = -EREMOTEIO; + } else { td->urb->actual_length = td->urb->transfer_buffer_length; + } } else { /* Maybe the event was for the data stage? */ if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) { @@ -992,16 +1007,20 @@ static int handle_tx_event(struct xhci_hcd *xhci, TRB_LEN(event->transfer_len)); td->urb->actual_length = 0; } - if (td->urb->transfer_flags & URB_SHORT_NOT_OK) - status = -EREMOTEIO; - else - status = 0; + /* Don't overwrite a previously set error code */ + if (status == -EINPROGRESS) { + if (td->urb->transfer_flags & URB_SHORT_NOT_OK) + status = -EREMOTEIO; + else + status = 0; + } } else { td->urb->actual_length = td->urb->transfer_buffer_length; /* Ignore a short packet completion if the * untransferred length was zero. */ - status = 0; + if (status == -EREMOTEIO) + status = 0; } } else { /* Slow path - walk the list, starting from the dequeue @@ -1028,19 +1047,30 @@ static int handle_tx_event(struct xhci_hcd *xhci, TRB_LEN(event->transfer_len); } } - /* The Endpoint Stop Command completion will take care of - * any stopped TDs. A stopped TD may be restarted, so don't update the - * ring dequeue pointer or take this TD off any lists yet. - */ if (GET_COMP_CODE(event->transfer_len) == COMP_STOP_INVAL || GET_COMP_CODE(event->transfer_len) == COMP_STOP) { + /* The Endpoint Stop Command completion will take care of any + * stopped TDs. A stopped TD may be restarted, so don't update + * the ring dequeue pointer or take this TD off any lists yet. + */ ep_ring->stopped_td = td; ep_ring->stopped_trb = event_trb; } else { - /* Update ring dequeue pointer */ - while (ep_ring->dequeue != td->last_trb) + if (GET_COMP_CODE(event->transfer_len) == COMP_STALL) { + /* The transfer is completed from the driver's + * perspective, but we need to issue a set dequeue + * command for this stalled endpoint to move the dequeue + * pointer past the TD. We can't do that here because + * the halt condition must be cleared first. + */ + ep_ring->stopped_td = td; + ep_ring->stopped_trb = event_trb; + } else { + /* Update ring dequeue pointer */ + while (ep_ring->dequeue != td->last_trb) + inc_deq(xhci, ep_ring, false); inc_deq(xhci, ep_ring, false); - inc_deq(xhci, ep_ring, false); + } /* Clean up the endpoint's TD list */ urb = td->urb; @@ -1050,7 +1080,10 @@ static int handle_tx_event(struct xhci_hcd *xhci, list_del(&td->cancelled_td_list); ep_ring->cancels_pending--; } - kfree(td); + /* Leave the TD around for the reset endpoint function to use */ + if (GET_COMP_CODE(event->transfer_len) != COMP_STALL) { + kfree(td); + } urb->hcpriv = NULL; } cleanup: @@ -1166,13 +1199,13 @@ static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, */ xhci_warn(xhci, "WARN urb submitted to disabled ep\n"); return -ENOENT; - case EP_STATE_HALTED: case EP_STATE_ERROR: - xhci_warn(xhci, "WARN waiting for halt or error on ep " - "to be cleared\n"); + xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n"); /* FIXME event handling code for error needs to clear it */ /* XXX not sure if this should be -ENOENT or not */ return -EINVAL; + case EP_STATE_HALTED: + xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n"); case EP_STATE_STOPPED: case EP_STATE_RUNNING: break; @@ -1724,10 +1757,12 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id, u32 type = TRB_TYPE(TRB_SET_DEQ); addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr); - if (addr == 0) + if (addr == 0) { xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n"); xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n", deq_seg, deq_ptr); + return 0; + } return queue_command(xhci, lower_32_bits(addr) | cycle_state, upper_32_bits(addr), 0, trb_slot_id | trb_ep_index | type); diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 9c108c632704..d31d32206ba3 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -952,6 +952,12 @@ struct xhci_ring { u32 cycle_state; }; +struct xhci_dequeue_state { + struct xhci_segment *new_deq_seg; + union xhci_trb *new_deq_ptr; + int new_cycle_state; +}; + struct xhci_erst_entry { /* 64-bit event ring segment address */ u64 seg_addr; @@ -1203,6 +1209,12 @@ int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr, u32 slot_id); int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index); +void xhci_find_new_dequeue_state(struct xhci_hcd *xhci, + unsigned int slot_id, unsigned int ep_index, + struct xhci_td *cur_td, struct xhci_dequeue_state *state); +void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci, + struct xhci_ring *ep_ring, unsigned int slot_id, + unsigned int ep_index, struct xhci_dequeue_state *deq_state); /* xHCI roothub code */ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, -- cgit v1.2.3 From 044dcc824a167e3d39ba69a49e2b723dd10678f6 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Sun, 26 Jul 2009 18:27:29 +0200 Subject: pata_pcmcia: add CNF-CDROM-ID Fixes this report: http://article.gmane.org/gmane.linux.kernel.pcmcia.devel/2228/ Reported-by: John McGrath Signed-off-by: Wolfram Sang Signed-off-by: Jeff Garzik --- drivers/ata/pata_pcmcia.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c index f4d009ed50ac..dc99e26f8e5b 100644 --- a/drivers/ata/pata_pcmcia.c +++ b/drivers/ata/pata_pcmcia.c @@ -411,6 +411,7 @@ static struct pcmcia_device_id pcmcia_devices[] = { PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9), PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591), PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728), + PCMCIA_DEVICE_PROD_ID12("CNF ", "CD-ROM", 0x46d7db81, 0x66536591), PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591), PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4), PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde), -- cgit v1.2.3 From 705d201414382b0966d7c903d738dfdb9380e4af Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 26 Jul 2009 16:21:01 +0200 Subject: libata: add missing NULL pointer check to ata_eh_reset() drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave' Please note that this is _not_ a real bug at the moment since ata_eh_context structure is embedded into ata_list structure and the code alwas checks for 'slave' before accessing 'sehc'. Anyway lets add missing check and always have a valid 'sehc' pointer (which makes code easier to understand and prevents introducing some possible bugs in the future). Reported-by: Dan Carpenter Cc: corbet@lwn.net Cc: eteo@redhat.com Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/libata-eh.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index 1a07c061f644..79711b64054b 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -2327,7 +2327,7 @@ int ata_eh_reset(struct ata_link *link, int classify, struct ata_port *ap = link->ap; struct ata_link *slave = ap->slave_link; struct ata_eh_context *ehc = &link->eh_context; - struct ata_eh_context *sehc = &slave->eh_context; + struct ata_eh_context *sehc = slave ? &slave->eh_context : NULL; unsigned int *classes = ehc->classes; unsigned int lflags = link->flags; int verbose = !(ehc->i.flags & ATA_EHI_QUIET); -- cgit v1.2.3 From c9abde12d6debe5b97f36fb43cf188c1b9cd477f Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 26 Jul 2009 16:05:13 +0200 Subject: libata: remove superfluous NULL pointer checks host->ports[] always contain pointers to valid port structures since a "dummy port" structure is used in case if there is no physical port. This patch takes care of two entries from Dan's list: drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap' drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap' and of another needless NULL pointer check in pata_octeon_cf.c. Reported-by: Dan Carpenter Cc: corbet@lwn.net Cc: eteo@redhat.com Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/pata_octeon_cf.c | 3 ++- drivers/ata/sata_mv.c | 2 +- drivers/ata/sata_sil.c | 2 +- 3 files changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c index 8d9343accf3c..abdd19fe990a 100644 --- a/drivers/ata/pata_octeon_cf.c +++ b/drivers/ata/pata_octeon_cf.c @@ -653,7 +653,8 @@ static irqreturn_t octeon_cf_interrupt(int irq, void *dev_instance) ap = host->ports[i]; ocd = ap->dev->platform_data; - if (!ap || (ap->flags & ATA_FLAG_DISABLED)) + + if (ap->flags & ATA_FLAG_DISABLED) continue; ocd = ap->dev->platform_data; diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 23714aefb825..c19417e02208 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -2514,7 +2514,7 @@ static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled) char *when = "idle"; ata_ehi_clear_desc(ehi); - if (!ap || (ap->flags & ATA_FLAG_DISABLED)) { + if (ap->flags & ATA_FLAG_DISABLED) { when = "disabled"; } else if (edma_was_enabled) { when = "EDMA enabled"; diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c index 030ec079b184..35bd5cc7f285 100644 --- a/drivers/ata/sata_sil.c +++ b/drivers/ata/sata_sil.c @@ -532,7 +532,7 @@ static irqreturn_t sil_interrupt(int irq, void *dev_instance) struct ata_port *ap = host->ports[i]; u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2); - if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED)) + if (unlikely(ap->flags & ATA_FLAG_DISABLED)) continue; /* turn off SATA_IRQ if not supported */ -- cgit v1.2.3 From c1f57d9b9846e7366c328f916d1a82d03ba4312c Mon Sep 17 00:00:00 2001 From: David Milburn Date: Wed, 22 Jul 2009 15:15:56 -0500 Subject: ahci: add device IDs for Ibex Peak ahci controllers Add device IDS for Ibex Peak SATA AHCI Controllers Signed-off-by: Jaroslav Kysela Signed-off-by: David Milburn Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 336eb1ed73cc..958c1fa41900 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -515,10 +515,14 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a22), board_ahci }, /* ICH10 */ { PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */ + { PCI_VDEVICE(INTEL, 0x3b22), board_ahci }, /* PCH AHCI */ + { PCI_VDEVICE(INTEL, 0x3b23), board_ahci }, /* PCH AHCI */ { PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */ { PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */ + { PCI_VDEVICE(INTEL, 0x3b29), board_ahci }, /* PCH AHCI */ { PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */ { PCI_VDEVICE(INTEL, 0x3b2c), board_ahci }, /* PCH RAID */ + { PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */ /* JMicron 360/1/3/5/6, match class to avoid IDE function */ { PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, -- cgit v1.2.3 From 6034734d333c1bd01119a5b480b34a507a3adf56 Mon Sep 17 00:00:00 2001 From: Steve Conklin Date: Thu, 16 Jul 2009 16:27:56 -0500 Subject: ata_piix: Add new laptop short cable IDs OriginalAuthor: Michael Frey Signed-off-by: Steve Conklin Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index d0a14cf2bd74..deada1fe6a01 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -596,9 +596,11 @@ static const struct ich_laptop ich_laptop[] = { { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */ { 0x27DF, 0x1025, 0x0102 }, /* ICH7 on Acer 5602aWLMi */ { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */ + { 0x27DF, 0x1028, 0x02b0 }, /* ICH7 on unknown Dell */ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */ { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */ + { 0x27DF, 0x152D, 0x0778 }, /* ICH7 on unknown Intel */ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */ { 0x24CA, 0x1025, 0x003d }, /* ICH4 on ACER TM290 */ { 0x266F, 0x1025, 0x0066 }, /* ICH6 on ACER Aspire 1694WLMi */ -- cgit v1.2.3 From 760cdb7760be928e85a021552253eb1b39acdf37 Mon Sep 17 00:00:00 2001 From: Steve Conklin Date: Thu, 16 Jul 2009 16:31:10 -0500 Subject: ata_piix: Add new short cable ID OriginalAuthor: Tony Espy Signed-off-by: Steve Conklin Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index deada1fe6a01..56b8a3ff1286 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -599,6 +599,7 @@ static const struct ich_laptop ich_laptop[] = { { 0x27DF, 0x1028, 0x02b0 }, /* ICH7 on unknown Dell */ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */ + { 0x27DF, 0x103C, 0x361a }, /* ICH7 on unkown HP */ { 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */ { 0x27DF, 0x152D, 0x0778 }, /* ICH7 on unknown Intel */ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on ACER Aspire 2023WLMi */ -- cgit v1.2.3 From 7d084d96fdf1d791cb171da57efc1ca89d68dd6c Mon Sep 17 00:00:00 2001 From: Sergey Matyukevich Date: Thu, 16 Jul 2009 22:38:55 +0400 Subject: libata: Updates and fixes for pata_at91 driver Please consider the following updates and fixes for pata_at91 driver. * Removed extra headers Here we need only static memory controller properties, which are contained in generic header at91sam9_smc.h. No need to include any specific headers for at91sam9260 SoC. * No harsh BUG_ON for get_clk in set_smc_timing function get_clk is now performed in driver probing function, probing fails if master clock is not available * Fixed uint/ulong mess in calc_mck_cycles function Signed-off-by: Sergey Matyukevich Signed-off-by: Jeff Garzik --- drivers/ata/pata_at91.c | 67 ++++++++++++++++++++++++++----------------------- 1 file changed, 36 insertions(+), 31 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 8561a9f195c1..5702affcb325 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -26,9 +26,7 @@ #include #include -#include #include -#include #include #include @@ -44,65 +42,62 @@ struct at91_ide_info { unsigned long mode; unsigned int cs; + struct clk *mck; + void __iomem *ide_addr; void __iomem *alt_addr; }; -const struct ata_timing initial_timing = +static const struct ata_timing initial_timing = {XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0}; -static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz) +static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz) { unsigned long mul; - /* - * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] = - * x * (f / 1_000_000_000) = - * x * ((f * 65536) / 1_000_000_000) / 65536 = - * x * (((f / 10_000) * 65536) / 100_000) / 65536 = - */ + /* + * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] = + * x * (f / 1_000_000_000) = + * x * ((f * 65536) / 1_000_000_000) / 65536 = + * x * (((f / 10_000) * 65536) / 100_000) / 65536 = + */ - mul = (mck_hz / 10000) << 16; - mul /= 100000; + mul = (mck_hz / 10000) << 16; + mul /= 100000; - return (ns * mul + 65536) >> 16; /* rounding */ + return (ns * mul + 65536) >> 16; /* rounding */ } static void set_smc_mode(struct at91_ide_info *info) { - at91_sys_write(AT91_SMC_MODE(info->cs), info->mode); - return; + at91_sys_write(AT91_SMC_MODE(info->cs), info->mode); + return; } static void set_smc_timing(struct device *dev, struct at91_ide_info *info, const struct ata_timing *ata) { - int read_cycle, write_cycle, active, recover; - int nrd_setup, nrd_pulse, nrd_recover; - int nwe_setup, nwe_pulse; + unsigned long read_cycle, write_cycle, active, recover; + unsigned long nrd_setup, nrd_pulse, nrd_recover; + unsigned long nwe_setup, nwe_pulse; - int ncs_write_setup, ncs_write_pulse; - int ncs_read_setup, ncs_read_pulse; + unsigned long ncs_write_setup, ncs_write_pulse; + unsigned long ncs_read_setup, ncs_read_pulse; - unsigned int mck_hz; - struct clk *mck; + unsigned long mck_hz; read_cycle = ata->cyc8b; nrd_setup = ata->setup; nrd_pulse = ata->act8b; nrd_recover = ata->rec8b; - mck = clk_get(NULL, "mck"); - BUG_ON(IS_ERR(mck)); - mck_hz = clk_get_rate(mck); + mck_hz = clk_get_rate(info->mck); read_cycle = calc_mck_cycles(read_cycle, mck_hz); nrd_setup = calc_mck_cycles(nrd_setup, mck_hz); nrd_pulse = calc_mck_cycles(nrd_pulse, mck_hz); nrd_recover = calc_mck_cycles(nrd_recover, mck_hz); - clk_put(mck); - active = nrd_setup + nrd_pulse; recover = read_cycle - active; @@ -121,13 +116,13 @@ static void set_smc_timing(struct device *dev, ncs_write_setup = ncs_read_setup; ncs_write_pulse = ncs_read_pulse; - dev_dbg(dev, "ATA timings: nrd_setup = %d nrd_pulse = %d nrd_cycle = %d\n", + dev_dbg(dev, "ATA timings: nrd_setup = %lu nrd_pulse = %lu nrd_cycle = %lu\n", nrd_setup, nrd_pulse, read_cycle); - dev_dbg(dev, "ATA timings: nwe_setup = %d nwe_pulse = %d nwe_cycle = %d\n", + dev_dbg(dev, "ATA timings: nwe_setup = %lu nwe_pulse = %lu nwe_cycle = %lu\n", nwe_setup, nwe_pulse, write_cycle); - dev_dbg(dev, "ATA timings: ncs_read_setup = %d ncs_read_pulse = %d\n", + dev_dbg(dev, "ATA timings: ncs_read_setup = %lu ncs_read_pulse = %lu\n", ncs_read_setup, ncs_read_pulse); - dev_dbg(dev, "ATA timings: ncs_write_setup = %d ncs_write_pulse = %d\n", + dev_dbg(dev, "ATA timings: ncs_write_setup = %lu ncs_write_pulse = %lu\n", ncs_write_setup, ncs_write_pulse); at91_sys_write(AT91_SMC_SETUP(info->cs), @@ -217,6 +212,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) struct resource *mem_res; struct ata_host *host; struct ata_port *ap; + int irq_flags = 0; int irq = 0; int ret; @@ -261,6 +257,13 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) return -ENOMEM; } + info->mck = clk_get(NULL, "mck"); + + if (IS_ERR(info->mck)) { + dev_err(dev, "failed to get access to mck clock\n"); + return -ENODEV; + } + info->cs = board->chipselect; info->mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT | @@ -304,6 +307,7 @@ err_alt_ioremap: devm_iounmap(dev, info->ide_addr); err_ide_ioremap: + clk_put(info->mck); kfree(info); return ret; @@ -326,6 +330,7 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) devm_iounmap(dev, info->ide_addr); devm_iounmap(dev, info->alt_addr); + clk_put(info->mck); kfree(info); return 0; -- cgit v1.2.3 From 5920dadfb4aec6c1372c5570e71bcd3b4837e63c Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Wed, 15 Jul 2009 17:11:41 +0900 Subject: libata: accept late unlocking of HPA On certain configurations, HPA isn't or can't be unlocked during probing but it somehow ends up unlocked afterwards. In the following thread, the problem can be reliably reproduced after resuming from STR. The BIOS turns on HPA during boot but forgets to do it during resume. http://thread.gmane.org/gmane.linux.kernel/858310 This patch updates libata revalidation such that it considers native n_sectors. If the device size has increased to match native n_sectors, it's assumed that HPA has been unlocked involuntarily and the device is recognized as the same one. This should be fairly safe while nicely working around the problem. Signed-off-by: Tejun Heo Reported-by: Christof Warlich Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 30 +++++++++++++++++++++++------- include/linux/libata.h | 1 + 2 files changed, 24 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 2c6aedaef718..8ac98ff16d7d 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -1515,6 +1515,7 @@ static int ata_hpa_resize(struct ata_device *dev) return rc; } + dev->n_native_sectors = native_sectors; /* nothing to do? */ if (native_sectors <= sectors || !ata_ignore_hpa) { @@ -4099,6 +4100,7 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class, unsigned int readid_flags) { u64 n_sectors = dev->n_sectors; + u64 n_native_sectors = dev->n_native_sectors; int rc; if (!ata_dev_enabled(dev)) @@ -4128,16 +4130,30 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class, /* verify n_sectors hasn't changed */ if (dev->class == ATA_DEV_ATA && n_sectors && dev->n_sectors != n_sectors) { - ata_dev_printk(dev, KERN_INFO, "n_sectors mismatch " + ata_dev_printk(dev, KERN_WARNING, "n_sectors mismatch " "%llu != %llu\n", (unsigned long long)n_sectors, (unsigned long long)dev->n_sectors); - - /* restore original n_sectors */ - dev->n_sectors = n_sectors; - - rc = -ENODEV; - goto fail; + /* + * Something could have caused HPA to be unlocked + * involuntarily. If n_native_sectors hasn't changed + * and the new size matches it, keep the device. + */ + if (dev->n_native_sectors == n_native_sectors && + dev->n_sectors > n_sectors && + dev->n_sectors == n_native_sectors) { + ata_dev_printk(dev, KERN_WARNING, + "new n_sectors matches native, probably " + "late HPA unlock, continuing\n"); + /* keep using the old n_sectors */ + dev->n_sectors = n_sectors; + } else { + /* restore original n_[native]_sectors and fail */ + dev->n_native_sectors = n_native_sectors; + dev->n_sectors = n_sectors; + rc = -ENODEV; + goto fail; + } } return 0; diff --git a/include/linux/libata.h b/include/linux/libata.h index 79b6d7fd4ac2..e5b6e33c6571 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -589,6 +589,7 @@ struct ata_device { #endif /* n_sector is CLEAR_BEGIN, read comment above CLEAR_BEGIN */ u64 n_sectors; /* size of device, if ATA */ + u64 n_native_sectors; /* native size, if ATA */ unsigned int class; /* ATA_DEV_xxx */ unsigned long unpark_deadline; -- cgit v1.2.3 From 68dbcb726e372b3c8ef60b79b5aff4174dd2bdf0 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Tue, 28 Jul 2009 22:36:59 -0400 Subject: Remove zero-length file drivers/char/vr41xx_giu.c Signed-off-by: Jeff Garzik --- drivers/char/vr41xx_giu.c | 0 1 file changed, 0 insertions(+), 0 deletions(-) delete mode 100644 drivers/char/vr41xx_giu.c (limited to 'drivers') diff --git a/drivers/char/vr41xx_giu.c b/drivers/char/vr41xx_giu.c deleted file mode 100644 index e69de29bb2d1..000000000000 -- cgit v1.2.3 From e024e11070a0a0dc7163ce1ec2da354a638bdbed Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 24 Jun 2009 09:48:08 +1000 Subject: drm/radeon/kms: add initial colortiling support. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This adds new set/get tiling interfaces where the pitch and macro/micro tiling enables can be set. Along with a flag to decide if this object should have a surface when mapped. The only thing we need to allocate with a mapped surface should be the frontbuffer. Note rotate scanout shouldn't require one, and back/depth shouldn't either, though mesa needs some fixes. It fixes the TTM interfaces along Thomas's suggestions, and I've tested the surface stealing code with two X servers and not seen any lockdep issues. I've stopped tiling the fbcon frontbuffer, as I don't see there being any advantage other than testing, I've left the testing commands in there, just flip the fb_tiled to true in radeon_fb.c Open: Can we integrate endian swapping in with this? Future features: texture tiling - need to relocate texture registers TXOFFSET* with tiling info. This also merges Michel's cleanup surfaces regs at init time patch even though it makes sense on its own, this patch really relies on it. Some PowerMac firmwares set up a tiling surface at the beginning of VRAM which messes us up otherwise. that patch is: Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 11 ++- drivers/gpu/drm/radeon/r100.c | 79 ++++++++++++++++- drivers/gpu/drm/radeon/r300.c | 51 ++++++++++- drivers/gpu/drm/radeon/r300_reg.h | 4 +- drivers/gpu/drm/radeon/radeon.h | 32 ++++++- drivers/gpu/drm/radeon/radeon_asic.h | 19 ++++ drivers/gpu/drm/radeon/radeon_device.c | 2 + drivers/gpu/drm/radeon/radeon_fb.c | 12 ++- drivers/gpu/drm/radeon/radeon_gem.c | 41 +++++++++ drivers/gpu/drm/radeon/radeon_kms.c | 2 + drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 15 ++-- drivers/gpu/drm/radeon/radeon_object.c | 130 ++++++++++++++++++++++++++++ drivers/gpu/drm/radeon/radeon_ttm.c | 2 + drivers/gpu/drm/ttm/ttm_bo.c | 5 +- drivers/gpu/drm/ttm/ttm_bo_vm.c | 3 + include/drm/radeon_drm.h | 23 ++++- include/drm/ttm/ttm_bo_driver.h | 15 ++++ 17 files changed, 427 insertions(+), 19 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index e64a199b5ee1..eac26cdb5dae 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -327,7 +327,7 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y, struct drm_gem_object *obj; struct drm_radeon_gem_object *obj_priv; uint64_t fb_location; - uint32_t fb_format, fb_pitch_pixels; + uint32_t fb_format, fb_pitch_pixels, tiling_flags; if (!crtc->fb) return -EINVAL; @@ -364,7 +364,14 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y, return -EINVAL; } - /* TODO tiling */ + radeon_object_get_tiling_flags(obj->driver_private, + &tiling_flags, NULL); + if (tiling_flags & RADEON_TILING_MACRO) + fb_format |= AVIVO_D1GRPH_MACRO_ADDRESS_MODE; + + if (tiling_flags & RADEON_TILING_MICRO) + fb_format |= AVIVO_D1GRPH_TILED; + if (radeon_crtc->crtc_id == 0) WREG32(AVIVO_D1VGA_CONTROL, 0); else diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 0d05909f03f6..69bd7cb59972 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -909,6 +909,7 @@ static int r100_packet0_check(struct radeon_cs_parser *p, unsigned idx; bool onereg; int r; + u32 tile_flags = 0; ib = p->ib->ptr; ib_chunk = &p->chunks[p->chunk_ib_idx]; @@ -942,7 +943,20 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } tmp = ib_chunk->kdata[idx] & 0x003fffff; tmp += (((u32)reloc->lobj.gpu_offset) >> 10); - ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp; + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_DST_TILE_MACRO; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) { + if (reg == RADEON_SRC_PITCH_OFFSET) { + DRM_ERROR("Cannot src blit from microtiled surface\n"); + r100_cs_dump_packet(p, pkt); + return -EINVAL; + } + tile_flags |= RADEON_DST_TILE_MICRO; + } + + tmp |= tile_flags; + ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp; break; case RADEON_RB3D_DEPTHOFFSET: case RADEON_RB3D_COLOROFFSET: @@ -987,6 +1001,25 @@ static int r100_packet0_check(struct radeon_cs_parser *p, } ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset); break; + case R300_RB3D_COLORPITCH0: + case RADEON_RB3D_COLORPITCH: + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_COLOR_TILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= RADEON_COLOR_MICROTILE_ENABLE; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + break; default: /* FIXME: we don't want to allow anyothers packet */ break; @@ -1707,3 +1740,47 @@ int r100_debugfs_mc_info_init(struct radeon_device *rdev) return 0; #endif } + +int r100_set_surface_reg(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size) +{ + int surf_index = reg * 16; + int flags = 0; + + /* r100/r200 divide by 16 */ + if (rdev->family < CHIP_R300) + flags = pitch / 16; + else + flags = pitch / 8; + + if (rdev->family <= CHIP_RS200) { + if ((tiling_flags & (RADEON_TILING_MACRO|RADEON_TILING_MICRO)) + == (RADEON_TILING_MACRO|RADEON_TILING_MICRO)) + flags |= RADEON_SURF_TILE_COLOR_BOTH; + if (tiling_flags & RADEON_TILING_MACRO) + flags |= RADEON_SURF_TILE_COLOR_MACRO; + } else if (rdev->family <= CHIP_RV280) { + if (tiling_flags & (RADEON_TILING_MACRO)) + flags |= R200_SURF_TILE_COLOR_MACRO; + if (tiling_flags & RADEON_TILING_MICRO) + flags |= R200_SURF_TILE_COLOR_MICRO; + } else { + if (tiling_flags & RADEON_TILING_MACRO) + flags |= R300_SURF_TILE_MACRO; + if (tiling_flags & RADEON_TILING_MICRO) + flags |= R300_SURF_TILE_MICRO; + } + + DRM_DEBUG("writing surface %d %d %x %x\n", reg, flags, offset, offset+obj_size-1); + WREG32(RADEON_SURFACE0_INFO + surf_index, flags); + WREG32(RADEON_SURFACE0_LOWER_BOUND + surf_index, offset); + WREG32(RADEON_SURFACE0_UPPER_BOUND + surf_index, offset + obj_size - 1); + return 0; +} + +void r100_clear_surface_reg(struct radeon_device *rdev, int reg) +{ + int surf_index = reg * 16; + WREG32(RADEON_SURFACE0_INFO + surf_index, 0); +} diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 0e0e094da503..28e5777658be 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -30,6 +30,7 @@ #include "drm.h" #include "radeon_reg.h" #include "radeon.h" +#include "radeon_drm.h" /* r300,r350,rv350,rv370,rv380 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -1023,7 +1024,7 @@ static int r300_packet0_check(struct radeon_cs_parser *p, struct radeon_cs_reloc *reloc; struct r300_cs_track *track; volatile uint32_t *ib; - uint32_t tmp; + uint32_t tmp, tile_flags = 0; unsigned i; int r; @@ -1052,7 +1053,19 @@ static int r300_packet0_check(struct radeon_cs_parser *p, } tmp = ib_chunk->kdata[idx] & 0x003fffff; tmp += (((u32)reloc->lobj.gpu_offset) >> 10); - ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp; + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= RADEON_DST_TILE_MACRO; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) { + if (reg == RADEON_SRC_PITCH_OFFSET) { + DRM_ERROR("Cannot src blit from microtiled surface\n"); + r100_cs_dump_packet(p, pkt); + return -EINVAL; + } + tile_flags |= RADEON_DST_TILE_MICRO; + } + tmp |= tile_flags; + ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp; break; case R300_RB3D_COLOROFFSET0: case R300_RB3D_COLOROFFSET1: @@ -1141,6 +1154,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p, /* RB3D_COLORPITCH1 */ /* RB3D_COLORPITCH2 */ /* RB3D_COLORPITCH3 */ + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= R300_COLOR_TILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= R300_COLOR_MICROTILE_ENABLE; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + i = (reg - 0x4E38) >> 2; track->cb[i].pitch = ib_chunk->kdata[idx] & 0x3FFE; switch (((ib_chunk->kdata[idx] >> 21) & 0xF)) { @@ -1196,6 +1226,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p, break; case 0x4F24: /* ZB_DEPTHPITCH */ + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + + if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO) + tile_flags |= R300_DEPTHMACROTILE_ENABLE; + if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) + tile_flags |= R300_DEPTHMICROTILE_TILED;; + + tmp = ib_chunk->kdata[idx] & ~(0x7 << 16); + tmp |= tile_flags; + ib[idx] = tmp; + track->zb.pitch = ib_chunk->kdata[idx] & 0x3FFC; break; case 0x4104: diff --git a/drivers/gpu/drm/radeon/r300_reg.h b/drivers/gpu/drm/radeon/r300_reg.h index 70f48609515e..4b7afef35a65 100644 --- a/drivers/gpu/drm/radeon/r300_reg.h +++ b/drivers/gpu/drm/radeon/r300_reg.h @@ -27,7 +27,9 @@ #ifndef _R300_REG_H_ #define _R300_REG_H_ - +#define R300_SURF_TILE_MACRO (1<<16) +#define R300_SURF_TILE_MICRO (2<<16) +#define R300_SURF_TILE_BOTH (3<<16) #define R300_MC_INIT_MISC_LAT_TIMER 0x180 diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 7f007185e7f7..af12a2fe3221 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -201,6 +201,14 @@ int radeon_fence_wait_last(struct radeon_device *rdev); struct radeon_fence *radeon_fence_ref(struct radeon_fence *fence); void radeon_fence_unref(struct radeon_fence **fence); +/* + * Tiling registers + */ +struct radeon_surface_reg { + struct radeon_object *robj; +}; + +#define RADEON_GEM_MAX_SURFACES 8 /* * Radeon buffer. @@ -213,6 +221,7 @@ struct radeon_object_list { uint64_t gpu_offset; unsigned rdomain; unsigned wdomain; + uint32_t tiling_flags; }; int radeon_object_init(struct radeon_device *rdev); @@ -242,8 +251,15 @@ void radeon_object_list_clean(struct list_head *head); int radeon_object_fbdev_mmap(struct radeon_object *robj, struct vm_area_struct *vma); unsigned long radeon_object_size(struct radeon_object *robj); - - +void radeon_object_clear_surface_reg(struct radeon_object *robj); +int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved, + bool force_drop); +void radeon_object_set_tiling_flags(struct radeon_object *robj, + uint32_t tiling_flags, uint32_t pitch); +void radeon_object_get_tiling_flags(struct radeon_object *robj, uint32_t *tiling_flags, uint32_t *pitch); +void radeon_bo_move_notify(struct ttm_buffer_object *bo, + struct ttm_mem_reg *mem); +void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo); /* * GEM objects. */ @@ -535,6 +551,11 @@ struct radeon_asic { void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock); void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes); void (*set_clock_gating)(struct radeon_device *rdev, int enable); + + int (*set_surface_reg)(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size); + int (*clear_surface_reg)(struct radeon_device *rdev, int reg); }; union radeon_asic_config { @@ -568,6 +589,10 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data, struct drm_file *filp); int radeon_cs_ioctl(struct drm_device *dev, void *data, struct drm_file *filp); +int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp); +int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp); /* @@ -627,6 +652,7 @@ struct radeon_device { bool shutdown; bool suspend; bool need_dma32; + struct radeon_surface_reg surface_regs[RADEON_GEM_MAX_SURFACES]; }; int radeon_device_init(struct radeon_device *rdev, @@ -801,5 +827,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_set_memory_clock(rdev, e) (rdev)->asic->set_engine_clock((rdev), (e)) #define radeon_set_pcie_lanes(rdev, l) (rdev)->asic->set_pcie_lanes((rdev), (l)) #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e)) +#define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s))) +#define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r))) #endif diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index e2e567395df8..dd903d329406 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -71,6 +71,10 @@ int r100_copy_blit(struct radeon_device *rdev, uint64_t dst_offset, unsigned num_pages, struct radeon_fence *fence); +int r100_set_surface_reg(struct radeon_device *rdev, int reg, + uint32_t tiling_flags, uint32_t pitch, + uint32_t offset, uint32_t obj_size); +int r100_clear_surface_reg(struct radeon_device *rdev, int reg); static struct radeon_asic r100_asic = { .init = &r100_init, @@ -100,6 +104,8 @@ static struct radeon_asic r100_asic = { .set_memory_clock = NULL, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -128,6 +134,7 @@ int r300_copy_dma(struct radeon_device *rdev, uint64_t dst_offset, unsigned num_pages, struct radeon_fence *fence); + static struct radeon_asic r300_asic = { .init = &r300_init, .errata = &r300_errata, @@ -156,6 +163,8 @@ static struct radeon_asic r300_asic = { .set_memory_clock = NULL, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; /* @@ -193,6 +202,8 @@ static struct radeon_asic r420_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -237,6 +248,8 @@ static struct radeon_asic rs400_asic = { .set_memory_clock = NULL, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_legacy_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -322,6 +335,8 @@ static struct radeon_asic rs690_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -367,6 +382,8 @@ static struct radeon_asic rv515_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; @@ -405,6 +422,8 @@ static struct radeon_asic r520_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = &rv370_set_pcie_lanes, .set_clock_gating = &radeon_atom_set_clock_gating, + .set_surface_reg = r100_set_surface_reg, + .clear_surface_reg = r100_clear_surface_reg, }; /* diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index cdef6eb01baf..f23083bbba3f 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -48,6 +48,8 @@ static void radeon_surface_init(struct radeon_device *rdev) i * (RADEON_SURFACE1_INFO - RADEON_SURFACE0_INFO), 0); } + /* enable surfaces */ + WREG32(RADEON_SURFACE_CNTL, 0); } } diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 260870a29d83..36d2f5588f20 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -471,10 +471,10 @@ static struct notifier_block paniced = { .notifier_call = radeonfb_panic, }; -static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp) +static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp, bool tiled) { int aligned = width; - int align_large = (ASIC_IS_AVIVO(rdev)); + int align_large = (ASIC_IS_AVIVO(rdev)) || tiled; int pitch_mask = 0; switch (bpp / 8) { @@ -512,12 +512,13 @@ int radeonfb_create(struct radeon_device *rdev, u64 fb_gpuaddr; void *fbptr = NULL; unsigned long tmp; + bool fb_tiled = false; /* useful for testing */ mode_cmd.width = surface_width; mode_cmd.height = surface_height; mode_cmd.bpp = 32; /* need to align pitch with crtc limits */ - mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp) * ((mode_cmd.bpp + 1) / 8); + mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp, fb_tiled) * ((mode_cmd.bpp + 1) / 8); mode_cmd.depth = 24; size = mode_cmd.pitch * mode_cmd.height; @@ -535,6 +536,8 @@ int radeonfb_create(struct radeon_device *rdev, } robj = gobj->driver_private; + if (fb_tiled) + radeon_object_set_tiling_flags(robj, RADEON_TILING_MACRO|RADEON_TILING_SURFACE, mode_cmd.pitch); mutex_lock(&rdev->ddev->struct_mutex); fb = radeon_framebuffer_create(rdev->ddev, &mode_cmd, gobj); if (fb == NULL) { @@ -563,6 +566,9 @@ int radeonfb_create(struct radeon_device *rdev, } rfbdev = info->par; + if (fb_tiled) + radeon_object_check_tiling(robj, 0, 0); + ret = radeon_object_kmap(robj, &fbptr); if (ret) { goto out_unref; diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index eb516034235d..12542087b298 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -285,3 +285,44 @@ int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data, mutex_unlock(&dev->struct_mutex); return r; } + +int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp) +{ + struct drm_radeon_gem_set_tiling *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r = 0; + + DRM_DEBUG("%d \n", args->handle); + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) + return -EINVAL; + robj = gobj->driver_private; + radeon_object_set_tiling_flags(robj, args->tiling_flags, args->pitch); + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); + return r; +} + +int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data, + struct drm_file *filp) +{ + struct drm_radeon_gem_get_tiling *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r = 0; + + DRM_DEBUG("\n"); + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) + return -EINVAL; + robj = gobj->driver_private; + radeon_object_get_tiling_flags(robj, &args->tiling_flags, + &args->pitch); + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); + return r; +} diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 4612a7c146d1..937a2f1cdb46 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -291,5 +291,7 @@ struct drm_ioctl_desc radeon_ioctls_kms[] = { DRM_IOCTL_DEF(DRM_RADEON_GEM_WAIT_IDLE, radeon_gem_wait_idle_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_CS, radeon_cs_ioctl, DRM_AUTH), DRM_IOCTL_DEF(DRM_RADEON_INFO, radeon_info_ioctl, DRM_AUTH), + DRM_IOCTL_DEF(DRM_RADEON_GEM_SET_TILING, radeon_gem_set_tiling_ioctl, DRM_AUTH), + DRM_IOCTL_DEF(DRM_RADEON_GEM_GET_TILING, radeon_gem_get_tiling_ioctl, DRM_AUTH), }; int radeon_max_kms_ioctl = DRM_ARRAY_SIZE(radeon_ioctls_kms); diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 14c1a5107fc9..0613790e2a5b 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -235,6 +235,7 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, uint64_t base; uint32_t crtc_offset, crtc_offset_cntl, crtc_tile_x0_y0 = 0; uint32_t crtc_pitch, pitch_pixels; + uint32_t tiling_flags; DRM_DEBUG("\n"); @@ -258,8 +259,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, (crtc->fb->bits_per_pixel * 8)); crtc_pitch |= crtc_pitch << 16; - /* TODO tiling */ - if (0) { + radeon_object_get_tiling_flags(obj->driver_private, + &tiling_flags, NULL); + if (tiling_flags & RADEON_TILING_MICRO) + DRM_ERROR("trying to scanout microtiled buffer\n"); + + if (tiling_flags & RADEON_TILING_MACRO) { if (ASIC_IS_R300(rdev)) crtc_offset_cntl |= (R300_CRTC_X_Y_MODE_EN | R300_CRTC_MICRO_TILE_BUFFER_DIS | @@ -275,15 +280,13 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y, crtc_offset_cntl &= ~RADEON_CRTC_TILE_EN; } - - /* TODO more tiling */ - if (0) { + if (tiling_flags & RADEON_TILING_MACRO) { if (ASIC_IS_R300(rdev)) { crtc_tile_x0_y0 = x | (y << 16); base &= ~0x7ff; } else { int byteshift = crtc->fb->bits_per_pixel >> 4; - int tile_addr = (((y >> 3) * crtc->fb->width + x) >> (8 - byteshift)) << 11; + int tile_addr = (((y >> 3) * pitch_pixels + x) >> (8 - byteshift)) << 11; base += tile_addr + ((x << byteshift) % 256) + ((y % 8) << 8); crtc_offset_cntl |= (y % 16); } diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index bac0d06c52ac..d5b1fd562d88 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -44,6 +44,9 @@ struct radeon_object { uint64_t gpu_addr; void *kptr; bool is_iomem; + uint32_t tiling_flags; + uint32_t pitch; + int surface_reg; }; int radeon_ttm_init(struct radeon_device *rdev); @@ -70,6 +73,7 @@ static void radeon_ttm_object_object_destroy(struct ttm_buffer_object *tobj) robj = container_of(tobj, struct radeon_object, tobj); list_del_init(&robj->list); + radeon_object_clear_surface_reg(robj); kfree(robj); } @@ -141,6 +145,7 @@ int radeon_object_create(struct radeon_device *rdev, } robj->rdev = rdev; robj->gobj = gobj; + robj->surface_reg = -1; INIT_LIST_HEAD(&robj->list); flags = radeon_object_flags_from_domain(domain); @@ -435,6 +440,7 @@ int radeon_object_list_validate(struct list_head *head, void *fence) radeon_object_gpu_addr(robj); } lobj->gpu_offset = robj->gpu_addr; + lobj->tiling_flags = robj->tiling_flags; if (fence) { old_fence = (struct radeon_fence *)robj->tobj.sync_obj; robj->tobj.sync_obj = radeon_fence_ref(fence); @@ -479,3 +485,127 @@ unsigned long radeon_object_size(struct radeon_object *robj) { return robj->tobj.num_pages << PAGE_SHIFT; } + +int radeon_object_get_surface_reg(struct radeon_object *robj) +{ + struct radeon_device *rdev = robj->rdev; + struct radeon_surface_reg *reg; + struct radeon_object *old_object; + int steal; + int i; + + if (!robj->tiling_flags) + return 0; + + if (robj->surface_reg >= 0) { + reg = &rdev->surface_regs[robj->surface_reg]; + i = robj->surface_reg; + goto out; + } + + steal = -1; + for (i = 0; i < RADEON_GEM_MAX_SURFACES; i++) { + + reg = &rdev->surface_regs[i]; + if (!reg->robj) + break; + + old_object = reg->robj; + if (old_object->pin_count == 0) + steal = i; + } + + /* if we are all out */ + if (i == RADEON_GEM_MAX_SURFACES) { + if (steal == -1) + return -ENOMEM; + /* find someone with a surface reg and nuke their BO */ + reg = &rdev->surface_regs[steal]; + old_object = reg->robj; + /* blow away the mapping */ + DRM_DEBUG("stealing surface reg %d from %p\n", steal, old_object); + ttm_bo_unmap_virtual(&old_object->tobj); + old_object->surface_reg = -1; + i = steal; + } + + robj->surface_reg = i; + reg->robj = robj; + +out: + radeon_set_surface_reg(rdev, i, robj->tiling_flags, robj->pitch, + robj->tobj.mem.mm_node->start << PAGE_SHIFT, + robj->tobj.num_pages << PAGE_SHIFT); + return 0; +} + +void radeon_object_clear_surface_reg(struct radeon_object *robj) +{ + struct radeon_device *rdev = robj->rdev; + struct radeon_surface_reg *reg; + + if (robj->surface_reg == -1) + return; + + reg = &rdev->surface_regs[robj->surface_reg]; + radeon_clear_surface_reg(rdev, robj->surface_reg); + + reg->robj = NULL; + robj->surface_reg = -1; +} + +void radeon_object_set_tiling_flags(struct radeon_object *robj, + uint32_t tiling_flags, uint32_t pitch) +{ + robj->tiling_flags = tiling_flags; + robj->pitch = pitch; +} + +void radeon_object_get_tiling_flags(struct radeon_object *robj, + uint32_t *tiling_flags, + uint32_t *pitch) +{ + if (tiling_flags) + *tiling_flags = robj->tiling_flags; + if (pitch) + *pitch = robj->pitch; +} + +int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved, + bool force_drop) +{ + if (!(robj->tiling_flags & RADEON_TILING_SURFACE)) + return 0; + + if (force_drop) { + radeon_object_clear_surface_reg(robj); + return 0; + } + + if (robj->tobj.mem.mem_type != TTM_PL_VRAM) { + if (!has_moved) + return 0; + + if (robj->surface_reg >= 0) + radeon_object_clear_surface_reg(robj); + return 0; + } + + if ((robj->surface_reg >= 0) && !has_moved) + return 0; + + return radeon_object_get_surface_reg(robj); +} + +void radeon_bo_move_notify(struct ttm_buffer_object *bo, + struct ttm_mem_reg *mem) +{ + struct radeon_object *robj = container_of(bo, struct radeon_object, tobj); + radeon_object_check_tiling(robj, 0, 1); +} + +void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo) +{ + struct radeon_object *robj = container_of(bo, struct radeon_object, tobj); + radeon_object_check_tiling(robj, 0, 0); +} diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 4ca9aa9203d0..37e1cbcce3a9 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -429,6 +429,8 @@ static struct ttm_bo_driver radeon_bo_driver = { .sync_obj_flush = &radeon_sync_obj_flush, .sync_obj_unref = &radeon_sync_obj_unref, .sync_obj_ref = &radeon_sync_obj_ref, + .move_notify = &radeon_bo_move_notify, + .fault_reserve_notify = &radeon_bo_fault_reserve_notify, }; int radeon_ttm_init(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index e55e7972c897..6538d4236989 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -43,7 +43,6 @@ #define TTM_BO_HASH_ORDER 13 static int ttm_bo_setup_vm(struct ttm_buffer_object *bo); -static void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo); static int ttm_bo_swapout(struct ttm_mem_shrink *shrink); static inline uint32_t ttm_bo_type_flags(unsigned type) @@ -307,6 +306,9 @@ static int ttm_bo_handle_move_mem(struct ttm_buffer_object *bo, } + if (bdev->driver->move_notify) + bdev->driver->move_notify(bo, mem); + if (!(old_man->flags & TTM_MEMTYPE_FLAG_FIXED) && !(new_man->flags & TTM_MEMTYPE_FLAG_FIXED)) ret = ttm_bo_move_ttm(bo, evict, no_wait, mem); @@ -1451,6 +1453,7 @@ void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo) unmap_mapping_range(bdev->dev_mapping, offset, holelen, 1); } +EXPORT_SYMBOL(ttm_bo_unmap_virtual); static void ttm_bo_vm_insert_rb(struct ttm_buffer_object *bo) { diff --git a/drivers/gpu/drm/ttm/ttm_bo_vm.c b/drivers/gpu/drm/ttm/ttm_bo_vm.c index 40b75032ea47..41c907f6c560 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_vm.c +++ b/drivers/gpu/drm/ttm/ttm_bo_vm.c @@ -101,6 +101,9 @@ static int ttm_bo_vm_fault(struct vm_area_struct *vma, struct vm_fault *vmf) return VM_FAULT_NOPAGE; } + if (bdev->driver->fault_reserve_notify) + bdev->driver->fault_reserve_notify(bo); + /* * Wait for buffer data in transit, due to a pipelined * move. diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index 41862e9a4c20..af4b4826997e 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -506,6 +506,8 @@ typedef struct { #define DRM_RADEON_GEM_WAIT_IDLE 0x24 #define DRM_RADEON_CS 0x26 #define DRM_RADEON_INFO 0x27 +#define DRM_RADEON_GEM_SET_TILING 0x28 +#define DRM_RADEON_GEM_GET_TILING 0x29 #define DRM_IOCTL_RADEON_CP_INIT DRM_IOW( DRM_COMMAND_BASE + DRM_RADEON_CP_INIT, drm_radeon_init_t) #define DRM_IOCTL_RADEON_CP_START DRM_IO( DRM_COMMAND_BASE + DRM_RADEON_CP_START) @@ -544,7 +546,8 @@ typedef struct { #define DRM_IOCTL_RADEON_GEM_WAIT_IDLE DRM_IOW(DRM_COMMAND_BASE + DRM_RADEON_GEM_WAIT_IDLE, struct drm_radeon_gem_wait_idle) #define DRM_IOCTL_RADEON_CS DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_CS, struct drm_radeon_cs) #define DRM_IOCTL_RADEON_INFO DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_INFO, struct drm_radeon_info) - +#define DRM_IOCTL_RADEON_SET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_SET_TILING, struct drm_radeon_gem_set_tiling) +#define DRM_IOCTL_RADEON_GET_TILING DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_GET_TILING, struct drm_radeon_gem_get_tiling) typedef struct drm_radeon_init { enum { @@ -796,6 +799,24 @@ struct drm_radeon_gem_create { uint32_t flags; }; +#define RADEON_TILING_MACRO 0x1 +#define RADEON_TILING_MICRO 0x2 +#define RADEON_TILING_SWAP 0x4 +#define RADEON_TILING_SURFACE 0x8 /* this object requires a surface + * when mapped - i.e. front buffer */ + +struct drm_radeon_gem_set_tiling { + uint32_t handle; + uint32_t tiling_flags; + uint32_t pitch; +}; + +struct drm_radeon_gem_get_tiling { + uint32_t handle; + uint32_t tiling_flags; + uint32_t pitch; +}; + struct drm_radeon_gem_mmap { uint32_t handle; uint32_t pad; diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h index ea83dd23a4d7..a68829db381a 100644 --- a/include/drm/ttm/ttm_bo_driver.h +++ b/include/drm/ttm/ttm_bo_driver.h @@ -354,6 +354,14 @@ struct ttm_bo_driver { int (*sync_obj_flush) (void *sync_obj, void *sync_arg); void (*sync_obj_unref) (void **sync_obj); void *(*sync_obj_ref) (void *sync_obj); + + /* hook to notify driver about a driver move so it + * can do tiling things */ + void (*move_notify)(struct ttm_buffer_object *bo, + struct ttm_mem_reg *new_mem); + /* notify the driver we are taking a fault on this BO + * and have reserved it */ + void (*fault_reserve_notify)(struct ttm_buffer_object *bo); }; #define TTM_NUM_MEM_TYPES 8 @@ -653,6 +661,13 @@ extern int ttm_bo_device_init(struct ttm_bo_device *bdev, struct ttm_bo_driver *driver, uint64_t file_page_offset, bool need_dma32); +/** + * ttm_bo_unmap_virtual + * + * @bo: tear down the virtual mappings for this BO + */ +extern void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo); + /** * ttm_bo_reserve: * -- cgit v1.2.3 From c93bb85b5cba3e3a06f2cad8e9bc5c23d3d10aac Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Mon, 13 Jul 2009 21:04:08 +0200 Subject: drm/radeon/kms: fix bandwidth computation on avivo hardware Fix bandwidth computation and crtc priority in memory controller so that crtc memory request are fullfill in time to avoid display artifact. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/atombios_crtc.c | 276 ++++----- drivers/gpu/drm/radeon/r100.c | 483 +++++++++++++++ drivers/gpu/drm/radeon/r300.c | 1 + drivers/gpu/drm/radeon/r520.c | 14 + drivers/gpu/drm/radeon/radeon.h | 40 +- drivers/gpu/drm/radeon/radeon_asic.h | 13 + drivers/gpu/drm/radeon/radeon_device.c | 10 +- drivers/gpu/drm/radeon/radeon_display.c | 68 ++- drivers/gpu/drm/radeon/radeon_encoders.c | 369 +---------- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 661 ++++++-------------- drivers/gpu/drm/radeon/radeon_legacy_encoders.c | 188 +----- drivers/gpu/drm/radeon/radeon_mode.h | 48 +- drivers/gpu/drm/radeon/radeon_share.h | 39 ++ drivers/gpu/drm/radeon/rs400.c | 1 + drivers/gpu/drm/radeon/rs600.c | 5 + drivers/gpu/drm/radeon/rs690.c | 472 +++++++++++++++ drivers/gpu/drm/radeon/rs690r.h | 99 +++ drivers/gpu/drm/radeon/rv515.c | 774 ++++++++++++++++++++---- drivers/gpu/drm/radeon/rv515r.h | 170 ++++++ 19 files changed, 2377 insertions(+), 1354 deletions(-) create mode 100644 drivers/gpu/drm/radeon/radeon_share.h create mode 100644 drivers/gpu/drm/radeon/rs690r.h create mode 100644 drivers/gpu/drm/radeon/rv515r.h (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c index eac26cdb5dae..74d034f77c6b 100644 --- a/drivers/gpu/drm/radeon/atombios_crtc.c +++ b/drivers/gpu/drm/radeon/atombios_crtc.c @@ -31,6 +31,132 @@ #include "atom.h" #include "atom-bits.h" +static void atombios_overscan_setup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + SET_CRTC_OVERSCAN_PS_ALLOCATION args; + int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan); + int a1, a2; + + memset(&args, 0, sizeof(args)); + + args.usOverscanRight = 0; + args.usOverscanLeft = 0; + args.usOverscanBottom = 0; + args.usOverscanTop = 0; + args.ucCRTC = radeon_crtc->crtc_id; + + switch (radeon_crtc->rmx_type) { + case RMX_CENTER: + args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; + args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; + args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; + args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + case RMX_ASPECT: + a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay; + a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay; + + if (a1 > a2) { + args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; + args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; + } else if (a2 > a1) { + args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; + args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; + } + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + case RMX_FULL: + default: + args.usOverscanRight = 0; + args.usOverscanLeft = 0; + args.usOverscanBottom = 0; + args.usOverscanTop = 0; + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + break; + } +} + +static void atombios_scaler_setup(struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + ENABLE_SCALER_PS_ALLOCATION args; + int index = GetIndexIntoMasterTable(COMMAND, EnableScaler); + /* fixme - fill in enc_priv for atom dac */ + enum radeon_tv_std tv_std = TV_STD_NTSC; + + if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id) + return; + + memset(&args, 0, sizeof(args)); + + args.ucScaler = radeon_crtc->crtc_id; + + if (radeon_crtc->devices & (ATOM_DEVICE_TV_SUPPORT)) { + switch (tv_std) { + case TV_STD_NTSC: + default: + args.ucTVStandard = ATOM_TV_NTSC; + break; + case TV_STD_PAL: + args.ucTVStandard = ATOM_TV_PAL; + break; + case TV_STD_PAL_M: + args.ucTVStandard = ATOM_TV_PALM; + break; + case TV_STD_PAL_60: + args.ucTVStandard = ATOM_TV_PAL60; + break; + case TV_STD_NTSC_J: + args.ucTVStandard = ATOM_TV_NTSCJ; + break; + case TV_STD_SCART_PAL: + args.ucTVStandard = ATOM_TV_PAL; /* ??? */ + break; + case TV_STD_SECAM: + args.ucTVStandard = ATOM_TV_SECAM; + break; + case TV_STD_PAL_CN: + args.ucTVStandard = ATOM_TV_PALCN; + break; + } + args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; + } else if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT)) { + args.ucTVStandard = ATOM_TV_CV; + args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; + } else { + switch (radeon_crtc->rmx_type) { + case RMX_FULL: + args.ucEnable = ATOM_SCALER_EXPANSION; + break; + case RMX_CENTER: + args.ucEnable = ATOM_SCALER_CENTER; + break; + case RMX_ASPECT: + args.ucEnable = ATOM_SCALER_EXPANSION; + break; + default: + if (ASIC_IS_AVIVO(rdev)) + args.ucEnable = ATOM_SCALER_DISABLE; + else + args.ucEnable = ATOM_SCALER_CENTER; + break; + } + } + atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); + if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT) + && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) { + atom_rv515_force_tv_scaler(rdev); + } +} + static void atombios_lock_crtc(struct drm_crtc *crtc, int lock) { struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); @@ -522,6 +648,9 @@ int atombios_crtc_mode_set(struct drm_crtc *crtc, radeon_crtc_set_base(crtc, x, y, old_fb); radeon_legacy_atom_set_surface(crtc); } + atombios_overscan_setup(crtc, mode, adjusted_mode); + atombios_scaler_setup(crtc); + radeon_bandwidth_update(rdev); return 0; } @@ -529,6 +658,8 @@ static bool atombios_crtc_mode_fixup(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { + if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode)) + return false; return true; } @@ -561,148 +692,3 @@ void radeon_atombios_init_crtc(struct drm_device *dev, AVIVO_D2CRTC_H_TOTAL - AVIVO_D1CRTC_H_TOTAL; drm_crtc_helper_add(&radeon_crtc->base, &atombios_helper_funcs); } - -void radeon_init_disp_bw_avivo(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2) -{ - struct radeon_device *rdev = dev->dev_private; - fixed20_12 min_mem_eff; - fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff; - fixed20_12 sclk_ff, mclk_ff; - uint32_t dc_lb_memory_split, temp; - - min_mem_eff.full = rfixed_const_8(0); - if (rdev->disp_priority == 2) { - uint32_t mc_init_misc_lat_timer = 0; - if (rdev->family == CHIP_RV515) - mc_init_misc_lat_timer = - RREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER); - else if (rdev->family == CHIP_RS690) - mc_init_misc_lat_timer = - RREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER); - - mc_init_misc_lat_timer &= - ~(R300_MC_DISP1R_INIT_LAT_MASK << - R300_MC_DISP1R_INIT_LAT_SHIFT); - mc_init_misc_lat_timer &= - ~(R300_MC_DISP0R_INIT_LAT_MASK << - R300_MC_DISP0R_INIT_LAT_SHIFT); - - if (mode2) - mc_init_misc_lat_timer |= - (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); - if (mode1) - mc_init_misc_lat_timer |= - (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); - - if (rdev->family == CHIP_RV515) - WREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER, - mc_init_misc_lat_timer); - else if (rdev->family == CHIP_RS690) - WREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER, - mc_init_misc_lat_timer); - } - - /* - * determine is there is enough bw for current mode - */ - temp_ff.full = rfixed_const(100); - mclk_ff.full = rfixed_const(rdev->clock.default_mclk); - mclk_ff.full = rfixed_div(mclk_ff, temp_ff); - sclk_ff.full = rfixed_const(rdev->clock.default_sclk); - sclk_ff.full = rfixed_div(sclk_ff, temp_ff); - - temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); - temp_ff.full = rfixed_const(temp); - mem_bw.full = rfixed_mul(mclk_ff, temp_ff); - mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); - - pix_clk.full = 0; - pix_clk2.full = 0; - peak_disp_bw.full = 0; - if (mode1) { - temp_ff.full = rfixed_const(1000); - pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ - pix_clk.full = rfixed_div(pix_clk, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes1); - peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); - } - if (mode2) { - temp_ff.full = rfixed_const(1000); - pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ - pix_clk2.full = rfixed_div(pix_clk2, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes2); - peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); - } - - if (peak_disp_bw.full >= mem_bw.full) { - DRM_ERROR - ("You may not have enough display bandwidth for current mode\n" - "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); - printk("peak disp bw %d, mem_bw %d\n", - rfixed_trunc(peak_disp_bw), rfixed_trunc(mem_bw)); - } - - /* - * Line Buffer Setup - * There is a single line buffer shared by both display controllers. - * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between the display - * controllers. The paritioning can either be done manually or via one of four - * preset allocations specified in bits 1:0: - * 0 - line buffer is divided in half and shared between each display controller - * 1 - D1 gets 3/4 of the line buffer, D2 gets 1/4 - * 2 - D1 gets the whole buffer - * 3 - D1 gets 1/4 of the line buffer, D2 gets 3/4 - * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual allocation mode. - * In manual allocation mode, D1 always starts at 0, D1 end/2 is specified in bits - * 14:4; D2 allocation follows D1. - */ - - /* is auto or manual better ? */ - dc_lb_memory_split = - RREG32(AVIVO_DC_LB_MEMORY_SPLIT) & ~AVIVO_DC_LB_MEMORY_SPLIT_MASK; - dc_lb_memory_split &= ~AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE; -#if 1 - /* auto */ - if (mode1 && mode2) { - if (mode1->hdisplay > mode2->hdisplay) { - if (mode1->hdisplay > 2560) - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q; - else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else if (mode2->hdisplay > mode1->hdisplay) { - if (mode2->hdisplay > 2560) - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; - else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else - dc_lb_memory_split |= - AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; - } else if (mode1) { - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_ONLY; - } else if (mode2) { - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; - } -#else - /* manual */ - dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE; - dc_lb_memory_split &= - ~(AVIVO_DC_LB_DISP1_END_ADR_MASK << - AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - if (mode1) { - dc_lb_memory_split |= - ((((mode1->hdisplay / 2) + 64) & AVIVO_DC_LB_DISP1_END_ADR_MASK) - << AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - } else if (mode2) { - dc_lb_memory_split |= (0 << AVIVO_DC_LB_DISP1_END_ADR_SHIFT); - } -#endif - WREG32(AVIVO_DC_LB_MEMORY_SPLIT, dc_lb_memory_split); -} diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 69bd7cb59972..0e00fef0b84f 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1784,3 +1784,486 @@ void r100_clear_surface_reg(struct radeon_device *rdev, int reg) int surf_index = reg * 16; WREG32(RADEON_SURFACE0_INFO + surf_index, 0); } + +void r100_bandwidth_update(struct radeon_device *rdev) +{ + fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff; + fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff; + fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff; + uint32_t temp, data, mem_trcd, mem_trp, mem_tras; + fixed20_12 memtcas_ff[8] = { + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(0), + fixed_init_half(1), + fixed_init_half(2), + fixed_init(0), + }; + fixed20_12 memtcas_rs480_ff[8] = { + fixed_init(0), + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(0), + fixed_init_half(1), + fixed_init_half(2), + fixed_init_half(3), + }; + fixed20_12 memtcas2_ff[8] = { + fixed_init(0), + fixed_init(1), + fixed_init(2), + fixed_init(3), + fixed_init(4), + fixed_init(5), + fixed_init(6), + fixed_init(7), + }; + fixed20_12 memtrbs[8] = { + fixed_init(1), + fixed_init_half(1), + fixed_init(2), + fixed_init_half(2), + fixed_init(3), + fixed_init_half(3), + fixed_init(4), + fixed_init_half(4) + }; + fixed20_12 memtrbs_r4xx[8] = { + fixed_init(4), + fixed_init(5), + fixed_init(6), + fixed_init(7), + fixed_init(8), + fixed_init(9), + fixed_init(10), + fixed_init(11) + }; + fixed20_12 min_mem_eff; + fixed20_12 mc_latency_sclk, mc_latency_mclk, k1; + fixed20_12 cur_latency_mclk, cur_latency_sclk; + fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate, + disp_drain_rate2, read_return_rate; + fixed20_12 time_disp1_drop_priority; + int c; + int cur_size = 16; /* in octawords */ + int critical_point = 0, critical_point2; +/* uint32_t read_return_rate, time_disp1_drop_priority; */ + int stop_req, max_stop_req; + struct drm_display_mode *mode1 = NULL; + struct drm_display_mode *mode2 = NULL; + uint32_t pixel_bytes1 = 0; + uint32_t pixel_bytes2 = 0; + + if (rdev->mode_info.crtcs[0]->base.enabled) { + mode1 = &rdev->mode_info.crtcs[0]->base.mode; + pixel_bytes1 = rdev->mode_info.crtcs[0]->base.fb->bits_per_pixel / 8; + } + if (rdev->mode_info.crtcs[1]->base.enabled) { + mode2 = &rdev->mode_info.crtcs[1]->base.mode; + pixel_bytes2 = rdev->mode_info.crtcs[1]->base.fb->bits_per_pixel / 8; + } + + min_mem_eff.full = rfixed_const_8(0); + /* get modes */ + if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) { + uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER); + mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT); + mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT); + /* check crtc enables */ + if (mode2) + mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); + if (mode1) + mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); + WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer); + } + + /* + * determine is there is enough bw for current mode + */ + mclk_ff.full = rfixed_const(rdev->clock.default_mclk); + temp_ff.full = rfixed_const(100); + mclk_ff.full = rfixed_div(mclk_ff, temp_ff); + sclk_ff.full = rfixed_const(rdev->clock.default_sclk); + sclk_ff.full = rfixed_div(sclk_ff, temp_ff); + + temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); + temp_ff.full = rfixed_const(temp); + mem_bw.full = rfixed_mul(mclk_ff, temp_ff); + + pix_clk.full = 0; + pix_clk2.full = 0; + peak_disp_bw.full = 0; + if (mode1) { + temp_ff.full = rfixed_const(1000); + pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ + pix_clk.full = rfixed_div(pix_clk, temp_ff); + temp_ff.full = rfixed_const(pixel_bytes1); + peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); + } + if (mode2) { + temp_ff.full = rfixed_const(1000); + pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ + pix_clk2.full = rfixed_div(pix_clk2, temp_ff); + temp_ff.full = rfixed_const(pixel_bytes2); + peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); + } + + mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); + if (peak_disp_bw.full >= mem_bw.full) { + DRM_ERROR("You may not have enough display bandwidth for current mode\n" + "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); + } + + /* Get values from the EXT_MEM_CNTL register...converting its contents. */ + temp = RREG32(RADEON_MEM_TIMING_CNTL); + if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */ + mem_trcd = ((temp >> 2) & 0x3) + 1; + mem_trp = ((temp & 0x3)) + 1; + mem_tras = ((temp & 0x70) >> 4) + 1; + } else if (rdev->family == CHIP_R300 || + rdev->family == CHIP_R350) { /* r300, r350 */ + mem_trcd = (temp & 0x7) + 1; + mem_trp = ((temp >> 8) & 0x7) + 1; + mem_tras = ((temp >> 11) & 0xf) + 4; + } else if (rdev->family == CHIP_RV350 || + rdev->family <= CHIP_RV380) { + /* rv3x0 */ + mem_trcd = (temp & 0x7) + 3; + mem_trp = ((temp >> 8) & 0x7) + 3; + mem_tras = ((temp >> 11) & 0xf) + 6; + } else if (rdev->family == CHIP_R420 || + rdev->family == CHIP_R423 || + rdev->family == CHIP_RV410) { + /* r4xx */ + mem_trcd = (temp & 0xf) + 3; + if (mem_trcd > 15) + mem_trcd = 15; + mem_trp = ((temp >> 8) & 0xf) + 3; + if (mem_trp > 15) + mem_trp = 15; + mem_tras = ((temp >> 12) & 0x1f) + 6; + if (mem_tras > 31) + mem_tras = 31; + } else { /* RV200, R200 */ + mem_trcd = (temp & 0x7) + 1; + mem_trp = ((temp >> 8) & 0x7) + 1; + mem_tras = ((temp >> 12) & 0xf) + 4; + } + /* convert to FF */ + trcd_ff.full = rfixed_const(mem_trcd); + trp_ff.full = rfixed_const(mem_trp); + tras_ff.full = rfixed_const(mem_tras); + + /* Get values from the MEM_SDRAM_MODE_REG register...converting its */ + temp = RREG32(RADEON_MEM_SDRAM_MODE_REG); + data = (temp & (7 << 20)) >> 20; + if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) { + if (rdev->family == CHIP_RS480) /* don't think rs400 */ + tcas_ff = memtcas_rs480_ff[data]; + else + tcas_ff = memtcas_ff[data]; + } else + tcas_ff = memtcas2_ff[data]; + + if (rdev->family == CHIP_RS400 || + rdev->family == CHIP_RS480) { + /* extra cas latency stored in bits 23-25 0-4 clocks */ + data = (temp >> 23) & 0x7; + if (data < 5) + tcas_ff.full += rfixed_const(data); + } + + if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) { + /* on the R300, Tcas is included in Trbs. + */ + temp = RREG32(RADEON_MEM_CNTL); + data = (R300_MEM_NUM_CHANNELS_MASK & temp); + if (data == 1) { + if (R300_MEM_USE_CD_CH_ONLY & temp) { + temp = RREG32(R300_MC_IND_INDEX); + temp &= ~R300_MC_IND_ADDR_MASK; + temp |= R300_MC_READ_CNTL_CD_mcind; + WREG32(R300_MC_IND_INDEX, temp); + temp = RREG32(R300_MC_IND_DATA); + data = (R300_MEM_RBS_POSITION_C_MASK & temp); + } else { + temp = RREG32(R300_MC_READ_CNTL_AB); + data = (R300_MEM_RBS_POSITION_A_MASK & temp); + } + } else { + temp = RREG32(R300_MC_READ_CNTL_AB); + data = (R300_MEM_RBS_POSITION_A_MASK & temp); + } + if (rdev->family == CHIP_RV410 || + rdev->family == CHIP_R420 || + rdev->family == CHIP_R423) + trbs_ff = memtrbs_r4xx[data]; + else + trbs_ff = memtrbs[data]; + tcas_ff.full += trbs_ff.full; + } + + sclk_eff_ff.full = sclk_ff.full; + + if (rdev->flags & RADEON_IS_AGP) { + fixed20_12 agpmode_ff; + agpmode_ff.full = rfixed_const(radeon_agpmode); + temp_ff.full = rfixed_const_666(16); + sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff); + } + /* TODO PCIE lanes may affect this - agpmode == 16?? */ + + if (ASIC_IS_R300(rdev)) { + sclk_delay_ff.full = rfixed_const(250); + } else { + if ((rdev->family == CHIP_RV100) || + rdev->flags & RADEON_IS_IGP) { + if (rdev->mc.vram_is_ddr) + sclk_delay_ff.full = rfixed_const(41); + else + sclk_delay_ff.full = rfixed_const(33); + } else { + if (rdev->mc.vram_width == 128) + sclk_delay_ff.full = rfixed_const(57); + else + sclk_delay_ff.full = rfixed_const(41); + } + } + + mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff); + + if (rdev->mc.vram_is_ddr) { + if (rdev->mc.vram_width == 32) { + k1.full = rfixed_const(40); + c = 3; + } else { + k1.full = rfixed_const(20); + c = 1; + } + } else { + k1.full = rfixed_const(40); + c = 3; + } + + temp_ff.full = rfixed_const(2); + mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff); + temp_ff.full = rfixed_const(c); + mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff); + temp_ff.full = rfixed_const(4); + mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff); + mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff); + mc_latency_mclk.full += k1.full; + + mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff); + mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff); + + /* + HW cursor time assuming worst case of full size colour cursor. + */ + temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1)))); + temp_ff.full += trcd_ff.full; + if (temp_ff.full < tras_ff.full) + temp_ff.full = tras_ff.full; + cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff); + + temp_ff.full = rfixed_const(cur_size); + cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff); + /* + Find the total latency for the display data. + */ + disp_latency_overhead.full = rfixed_const(80); + disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff); + mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full; + mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full; + + if (mc_latency_mclk.full > mc_latency_sclk.full) + disp_latency.full = mc_latency_mclk.full; + else + disp_latency.full = mc_latency_sclk.full; + + /* setup Max GRPH_STOP_REQ default value */ + if (ASIC_IS_RV100(rdev)) + max_stop_req = 0x5c; + else + max_stop_req = 0x7c; + + if (mode1) { + /* CRTC1 + Set GRPH_BUFFER_CNTL register using h/w defined optimal values. + GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ] + */ + stop_req = mode1->hdisplay * pixel_bytes1 / 16; + + if (stop_req > max_stop_req) + stop_req = max_stop_req; + + /* + Find the drain rate of the display buffer. + */ + temp_ff.full = rfixed_const((16/pixel_bytes1)); + disp_drain_rate.full = rfixed_div(pix_clk, temp_ff); + + /* + Find the critical point of the display buffer. + */ + crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency); + crit_point_ff.full += rfixed_const_half(0); + + critical_point = rfixed_trunc(crit_point_ff); + + if (rdev->disp_priority == 2) { + critical_point = 0; + } + + /* + The critical point should never be above max_stop_req-4. Setting + GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time. + */ + if (max_stop_req - critical_point < 4) + critical_point = 0; + + if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) { + /* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/ + critical_point = 0x10; + } + + temp = RREG32(RADEON_GRPH_BUFFER_CNTL); + temp &= ~(RADEON_GRPH_STOP_REQ_MASK); + temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); + temp &= ~(RADEON_GRPH_START_REQ_MASK); + if ((rdev->family == CHIP_R350) && + (stop_req > 0x15)) { + stop_req -= 0x10; + } + temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); + temp |= RADEON_GRPH_BUFFER_SIZE; + temp &= ~(RADEON_GRPH_CRITICAL_CNTL | + RADEON_GRPH_CRITICAL_AT_SOF | + RADEON_GRPH_STOP_CNTL); + /* + Write the result into the register. + */ + WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) | + (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT))); + +#if 0 + if ((rdev->family == CHIP_RS400) || + (rdev->family == CHIP_RS480)) { + /* attempt to program RS400 disp regs correctly ??? */ + temp = RREG32(RS400_DISP1_REG_CNTL); + temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK | + RS400_DISP1_STOP_REQ_LEVEL_MASK); + WREG32(RS400_DISP1_REQ_CNTL1, (temp | + (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) | + (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); + temp = RREG32(RS400_DMIF_MEM_CNTL1); + temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK | + RS400_DISP1_CRITICAL_POINT_STOP_MASK); + WREG32(RS400_DMIF_MEM_CNTL1, (temp | + (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) | + (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT))); + } +#endif + + DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n", + /* (unsigned int)info->SavedReg->grph_buffer_cntl, */ + (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL)); + } + + if (mode2) { + u32 grph2_cntl; + stop_req = mode2->hdisplay * pixel_bytes2 / 16; + + if (stop_req > max_stop_req) + stop_req = max_stop_req; + + /* + Find the drain rate of the display buffer. + */ + temp_ff.full = rfixed_const((16/pixel_bytes2)); + disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff); + + grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL); + grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK); + grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); + grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK); + if ((rdev->family == CHIP_R350) && + (stop_req > 0x15)) { + stop_req -= 0x10; + } + grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); + grph2_cntl |= RADEON_GRPH_BUFFER_SIZE; + grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL | + RADEON_GRPH_CRITICAL_AT_SOF | + RADEON_GRPH_STOP_CNTL); + + if ((rdev->family == CHIP_RS100) || + (rdev->family == CHIP_RS200)) + critical_point2 = 0; + else { + temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128; + temp_ff.full = rfixed_const(temp); + temp_ff.full = rfixed_mul(mclk_ff, temp_ff); + if (sclk_ff.full < temp_ff.full) + temp_ff.full = sclk_ff.full; + + read_return_rate.full = temp_ff.full; + + if (mode1) { + temp_ff.full = read_return_rate.full - disp_drain_rate.full; + time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff); + } else { + time_disp1_drop_priority.full = 0; + } + crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full; + crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2); + crit_point_ff.full += rfixed_const_half(0); + + critical_point2 = rfixed_trunc(crit_point_ff); + + if (rdev->disp_priority == 2) { + critical_point2 = 0; + } + + if (max_stop_req - critical_point2 < 4) + critical_point2 = 0; + + } + + if (critical_point2 == 0 && rdev->family == CHIP_R300) { + /* some R300 cards have problem with this set to 0 */ + critical_point2 = 0x10; + } + + WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) | + (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT))); + + if ((rdev->family == CHIP_RS400) || + (rdev->family == CHIP_RS480)) { +#if 0 + /* attempt to program RS400 disp2 regs correctly ??? */ + temp = RREG32(RS400_DISP2_REQ_CNTL1); + temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK | + RS400_DISP2_STOP_REQ_LEVEL_MASK); + WREG32(RS400_DISP2_REQ_CNTL1, (temp | + (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) | + (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); + temp = RREG32(RS400_DISP2_REQ_CNTL2); + temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK | + RS400_DISP2_CRITICAL_POINT_STOP_MASK); + WREG32(RS400_DISP2_REQ_CNTL2, (temp | + (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) | + (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT))); +#endif + WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC); + WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000); + WREG32(RS400_DMIF_MEM_CNTL1, 0x29CA71DC); + WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC); + } + + DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n", + (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL)); + } +} diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 28e5777658be..9c8d41534a5d 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -31,6 +31,7 @@ #include "radeon_reg.h" #include "radeon.h" #include "radeon_drm.h" +#include "radeon_share.h" /* r300,r350,rv350,rv370,rv380 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index b6bd3758db6b..0a981e2ee2f8 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -28,6 +28,7 @@ #include "drmP.h" #include "radeon_reg.h" #include "radeon.h" +#include "radeon_share.h" /* r520,rv530,rv560,rv570,r580 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -226,7 +227,20 @@ static void r520_vram_get_type(struct radeon_device *rdev) void r520_vram_info(struct radeon_device *rdev) { + fixed20_12 a; + r520_vram_get_type(rdev); r100_vram_init_sizes(rdev); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); +} + +void r520_bandwidth_update(struct radeon_device *rdev) +{ + rv515_bandwidth_avivo_update(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index af12a2fe3221..63a3fe32e584 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -113,6 +113,7 @@ enum radeon_family { CHIP_RV770, CHIP_RV730, CHIP_RV710, + CHIP_RS880, CHIP_LAST, }; @@ -490,6 +491,39 @@ struct radeon_wb { uint64_t gpu_addr; }; +/** + * struct radeon_pm - power management datas + * @max_bandwidth: maximum bandwidth the gpu has (MByte/s) + * @igp_sideport_mclk: sideport memory clock Mhz (rs690,rs740,rs780,rs880) + * @igp_system_mclk: system clock Mhz (rs690,rs740,rs780,rs880) + * @igp_ht_link_clk: ht link clock Mhz (rs690,rs740,rs780,rs880) + * @igp_ht_link_width: ht link width in bits (rs690,rs740,rs780,rs880) + * @k8_bandwidth: k8 bandwidth the gpu has (MByte/s) (IGP) + * @sideport_bandwidth: sideport bandwidth the gpu has (MByte/s) (IGP) + * @ht_bandwidth: ht bandwidth the gpu has (MByte/s) (IGP) + * @core_bandwidth: core GPU bandwidth the gpu has (MByte/s) (IGP) + * @sclk: GPU clock Mhz (core bandwith depends of this clock) + * @needed_bandwidth: current bandwidth needs + * + * It keeps track of various data needed to take powermanagement decision. + * Bandwith need is used to determine minimun clock of the GPU and memory. + * Equation between gpu/memory clock and available bandwidth is hw dependent + * (type of memory, bus size, efficiency, ...) + */ +struct radeon_pm { + fixed20_12 max_bandwidth; + fixed20_12 igp_sideport_mclk; + fixed20_12 igp_system_mclk; + fixed20_12 igp_ht_link_clk; + fixed20_12 igp_ht_link_width; + fixed20_12 k8_bandwidth; + fixed20_12 sideport_bandwidth; + fixed20_12 ht_bandwidth; + fixed20_12 core_bandwidth; + fixed20_12 sclk; + fixed20_12 needed_bandwidth; +}; + /* * Benchmarking @@ -551,19 +585,17 @@ struct radeon_asic { void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock); void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes); void (*set_clock_gating)(struct radeon_device *rdev, int enable); - int (*set_surface_reg)(struct radeon_device *rdev, int reg, uint32_t tiling_flags, uint32_t pitch, uint32_t offset, uint32_t obj_size); int (*clear_surface_reg)(struct radeon_device *rdev, int reg); + void (*bandwidth_update)(struct radeon_device *rdev); }; union radeon_asic_config { struct r300_asic r300; }; -/* r100 */ -void r100_vram_init_sizes(struct radeon_device *rdev); /* * IOCTL. @@ -646,6 +678,7 @@ struct radeon_device { struct radeon_irq irq; struct radeon_asic *asic; struct radeon_gem gem; + struct radeon_pm pm; struct mutex cs_mutex; struct radeon_wb wb; bool gpu_lockup; @@ -829,5 +862,6 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e)) #define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s))) #define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r))) +#define radeon_bandwidth_update(rdev) (rdev)->asic->bandwidth_update((rdev)) #endif diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index dd903d329406..9a75876e0c3b 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -75,6 +75,7 @@ int r100_set_surface_reg(struct radeon_device *rdev, int reg, uint32_t tiling_flags, uint32_t pitch, uint32_t offset, uint32_t obj_size); int r100_clear_surface_reg(struct radeon_device *rdev, int reg); +void r100_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic r100_asic = { .init = &r100_init, @@ -106,6 +107,7 @@ static struct radeon_asic r100_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -165,6 +167,7 @@ static struct radeon_asic r300_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; /* @@ -204,6 +207,7 @@ static struct radeon_asic r420_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -250,6 +254,7 @@ static struct radeon_asic rs400_asic = { .set_clock_gating = &radeon_legacy_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r100_bandwidth_update, }; @@ -267,6 +272,7 @@ void rs600_gart_tlb_flush(struct radeon_device *rdev); int rs600_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr); uint32_t rs600_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs600_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rs600_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs600_asic = { .init = &r300_init, .errata = &rs600_errata, @@ -295,6 +301,7 @@ static struct radeon_asic rs600_asic = { .set_memory_clock = &radeon_atom_set_memory_clock, .set_pcie_lanes = NULL, .set_clock_gating = &radeon_atom_set_clock_gating, + .bandwidth_update = &rs600_bandwidth_update, }; @@ -307,6 +314,7 @@ int rs690_mc_init(struct radeon_device *rdev); void rs690_mc_fini(struct radeon_device *rdev); uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rs690_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs690_asic = { .init = &r300_init, .errata = &rs690_errata, @@ -337,6 +345,7 @@ static struct radeon_asic rs690_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &rs690_bandwidth_update, }; @@ -354,6 +363,7 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); void rv515_ring_start(struct radeon_device *rdev); uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg); void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); +void rv515_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rv515_asic = { .init = &rv515_init, .errata = &rv515_errata, @@ -384,6 +394,7 @@ static struct radeon_asic rv515_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &rv515_bandwidth_update, }; @@ -394,6 +405,7 @@ void r520_errata(struct radeon_device *rdev); void r520_vram_info(struct radeon_device *rdev); int r520_mc_init(struct radeon_device *rdev); void r520_mc_fini(struct radeon_device *rdev); +void r520_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic r520_asic = { .init = &rv515_init, .errata = &r520_errata, @@ -424,6 +436,7 @@ static struct radeon_asic r520_asic = { .set_clock_gating = &radeon_atom_set_clock_gating, .set_surface_reg = r100_set_surface_reg, .clear_surface_reg = r100_clear_surface_reg, + .bandwidth_update = &r520_bandwidth_update, }; /* diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f23083bbba3f..f78db5c8008c 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -561,6 +561,11 @@ int radeon_device_init(struct radeon_device *rdev, radeon_combios_asic_init(rdev->ddev); } } + /* Initialize clocks */ + r = radeon_clocks_init(rdev); + if (r) { + return r; + } /* Get vram informations */ radeon_vram_info(rdev); @@ -572,11 +577,6 @@ int radeon_device_init(struct radeon_device *rdev, (unsigned)rdev->mc.aper_size >> 20); DRM_INFO("RAM width %dbits %cDR\n", rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S'); - /* Initialize clocks */ - r = radeon_clocks_init(rdev); - if (r) { - return r; - } /* Initialize memory controller (also test AGP) */ r = radeon_mc_init(rdev); if (r) { diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c index bc312f3d9a0a..a8fa1bb84cf7 100644 --- a/drivers/gpu/drm/radeon/radeon_display.c +++ b/drivers/gpu/drm/radeon/radeon_display.c @@ -187,6 +187,7 @@ static void radeon_crtc_init(struct drm_device *dev, int index) drm_mode_crtc_set_gamma_size(&radeon_crtc->base, 256); radeon_crtc->crtc_id = index; + rdev->mode_info.crtcs[index] = radeon_crtc; radeon_crtc->mode_set.crtc = &radeon_crtc->base; radeon_crtc->mode_set.connectors = (struct drm_connector **)(radeon_crtc + 1); @@ -661,36 +662,51 @@ void radeon_modeset_fini(struct radeon_device *rdev) } } -void radeon_init_disp_bandwidth(struct drm_device *dev) +bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) { - struct radeon_device *rdev = dev->dev_private; - struct drm_display_mode *modes[2]; - int pixel_bytes[2]; - struct drm_crtc *crtc; - - pixel_bytes[0] = pixel_bytes[1] = 0; - modes[0] = modes[1] = NULL; - - list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct drm_device *dev = crtc->dev; + struct drm_encoder *encoder; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct radeon_encoder *radeon_encoder; + bool first = true; - if (crtc->enabled && crtc->fb) { - modes[radeon_crtc->crtc_id] = &crtc->mode; - pixel_bytes[radeon_crtc->crtc_id] = crtc->fb->bits_per_pixel / 8; + list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) { + radeon_encoder = to_radeon_encoder(encoder); + if (encoder->crtc != crtc) + continue; + if (first) { + radeon_crtc->rmx_type = radeon_encoder->rmx_type; + radeon_crtc->devices = radeon_encoder->devices; + memcpy(&radeon_crtc->native_mode, + &radeon_encoder->native_mode, + sizeof(struct radeon_native_mode)); + first = false; + } else { + if (radeon_crtc->rmx_type != radeon_encoder->rmx_type) { + /* WARNING: Right now this can't happen but + * in the future we need to check that scaling + * are consistent accross different encoder + * (ie all encoder can work with the same + * scaling). + */ + DRM_ERROR("Scaling not consistent accross encoder.\n"); + return false; + } } } - - if (ASIC_IS_AVIVO(rdev)) { - radeon_init_disp_bw_avivo(dev, - modes[0], - pixel_bytes[0], - modes[1], - pixel_bytes[1]); + if (radeon_crtc->rmx_type != RMX_OFF) { + fixed20_12 a, b; + a.full = rfixed_const(crtc->mode.vdisplay); + b.full = rfixed_const(radeon_crtc->native_mode.panel_xres); + radeon_crtc->vsc.full = rfixed_div(a, b); + a.full = rfixed_const(crtc->mode.hdisplay); + b.full = rfixed_const(radeon_crtc->native_mode.panel_yres); + radeon_crtc->hsc.full = rfixed_div(a, b); } else { - radeon_init_disp_bw_legacy(dev, - modes[0], - pixel_bytes[0], - modes[1], - pixel_bytes[1]); + radeon_crtc->vsc.full = rfixed_const(1); + radeon_crtc->hsc.full = rfixed_const(1); } + return true; } diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c index ea15284e7580..0a92706eac19 100644 --- a/drivers/gpu/drm/radeon/radeon_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_encoders.c @@ -154,7 +154,6 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder, if (mode->hdisplay < native_mode->panel_xres || mode->vdisplay < native_mode->panel_yres) { - radeon_encoder->flags |= RADEON_USE_RMX; if (ASIC_IS_AVIVO(rdev)) { adjusted_mode->hdisplay = native_mode->panel_xres; adjusted_mode->vdisplay = native_mode->panel_yres; @@ -197,15 +196,13 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder, } } + static bool radeon_atom_mode_fixup(struct drm_encoder *encoder, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - radeon_encoder->flags &= ~RADEON_USE_RMX; - drm_mode_set_crtcinfo(adjusted_mode, 0); if (radeon_encoder->rmx_type != RMX_OFF) @@ -808,234 +805,6 @@ atombios_dig_transmitter_setup(struct drm_encoder *encoder, int action) } -static void atom_rv515_force_tv_scaler(struct radeon_device *rdev) -{ - - WREG32(0x659C, 0x0); - WREG32(0x6594, 0x705); - WREG32(0x65A4, 0x10001); - WREG32(0x65D8, 0x0); - WREG32(0x65B0, 0x0); - WREG32(0x65C0, 0x0); - WREG32(0x65D4, 0x0); - WREG32(0x6578, 0x0); - WREG32(0x657C, 0x841880A8); - WREG32(0x6578, 0x1); - WREG32(0x657C, 0x84208680); - WREG32(0x6578, 0x2); - WREG32(0x657C, 0xBFF880B0); - WREG32(0x6578, 0x100); - WREG32(0x657C, 0x83D88088); - WREG32(0x6578, 0x101); - WREG32(0x657C, 0x84608680); - WREG32(0x6578, 0x102); - WREG32(0x657C, 0xBFF080D0); - WREG32(0x6578, 0x200); - WREG32(0x657C, 0x83988068); - WREG32(0x6578, 0x201); - WREG32(0x657C, 0x84A08680); - WREG32(0x6578, 0x202); - WREG32(0x657C, 0xBFF080F8); - WREG32(0x6578, 0x300); - WREG32(0x657C, 0x83588058); - WREG32(0x6578, 0x301); - WREG32(0x657C, 0x84E08660); - WREG32(0x6578, 0x302); - WREG32(0x657C, 0xBFF88120); - WREG32(0x6578, 0x400); - WREG32(0x657C, 0x83188040); - WREG32(0x6578, 0x401); - WREG32(0x657C, 0x85008660); - WREG32(0x6578, 0x402); - WREG32(0x657C, 0xBFF88150); - WREG32(0x6578, 0x500); - WREG32(0x657C, 0x82D88030); - WREG32(0x6578, 0x501); - WREG32(0x657C, 0x85408640); - WREG32(0x6578, 0x502); - WREG32(0x657C, 0xBFF88180); - WREG32(0x6578, 0x600); - WREG32(0x657C, 0x82A08018); - WREG32(0x6578, 0x601); - WREG32(0x657C, 0x85808620); - WREG32(0x6578, 0x602); - WREG32(0x657C, 0xBFF081B8); - WREG32(0x6578, 0x700); - WREG32(0x657C, 0x82608010); - WREG32(0x6578, 0x701); - WREG32(0x657C, 0x85A08600); - WREG32(0x6578, 0x702); - WREG32(0x657C, 0x800081F0); - WREG32(0x6578, 0x800); - WREG32(0x657C, 0x8228BFF8); - WREG32(0x6578, 0x801); - WREG32(0x657C, 0x85E085E0); - WREG32(0x6578, 0x802); - WREG32(0x657C, 0xBFF88228); - WREG32(0x6578, 0x10000); - WREG32(0x657C, 0x82A8BF00); - WREG32(0x6578, 0x10001); - WREG32(0x657C, 0x82A08CC0); - WREG32(0x6578, 0x10002); - WREG32(0x657C, 0x8008BEF8); - WREG32(0x6578, 0x10100); - WREG32(0x657C, 0x81F0BF28); - WREG32(0x6578, 0x10101); - WREG32(0x657C, 0x83608CA0); - WREG32(0x6578, 0x10102); - WREG32(0x657C, 0x8018BED0); - WREG32(0x6578, 0x10200); - WREG32(0x657C, 0x8148BF38); - WREG32(0x6578, 0x10201); - WREG32(0x657C, 0x84408C80); - WREG32(0x6578, 0x10202); - WREG32(0x657C, 0x8008BEB8); - WREG32(0x6578, 0x10300); - WREG32(0x657C, 0x80B0BF78); - WREG32(0x6578, 0x10301); - WREG32(0x657C, 0x85008C20); - WREG32(0x6578, 0x10302); - WREG32(0x657C, 0x8020BEA0); - WREG32(0x6578, 0x10400); - WREG32(0x657C, 0x8028BF90); - WREG32(0x6578, 0x10401); - WREG32(0x657C, 0x85E08BC0); - WREG32(0x6578, 0x10402); - WREG32(0x657C, 0x8018BE90); - WREG32(0x6578, 0x10500); - WREG32(0x657C, 0xBFB8BFB0); - WREG32(0x6578, 0x10501); - WREG32(0x657C, 0x86C08B40); - WREG32(0x6578, 0x10502); - WREG32(0x657C, 0x8010BE90); - WREG32(0x6578, 0x10600); - WREG32(0x657C, 0xBF58BFC8); - WREG32(0x6578, 0x10601); - WREG32(0x657C, 0x87A08AA0); - WREG32(0x6578, 0x10602); - WREG32(0x657C, 0x8010BE98); - WREG32(0x6578, 0x10700); - WREG32(0x657C, 0xBF10BFF0); - WREG32(0x6578, 0x10701); - WREG32(0x657C, 0x886089E0); - WREG32(0x6578, 0x10702); - WREG32(0x657C, 0x8018BEB0); - WREG32(0x6578, 0x10800); - WREG32(0x657C, 0xBED8BFE8); - WREG32(0x6578, 0x10801); - WREG32(0x657C, 0x89408940); - WREG32(0x6578, 0x10802); - WREG32(0x657C, 0xBFE8BED8); - WREG32(0x6578, 0x20000); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20001); - WREG32(0x657C, 0x90008000); - WREG32(0x6578, 0x20002); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20003); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20100); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20101); - WREG32(0x657C, 0x8FE0BF70); - WREG32(0x6578, 0x20102); - WREG32(0x657C, 0xBFE880C0); - WREG32(0x6578, 0x20103); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20200); - WREG32(0x657C, 0x8018BFF8); - WREG32(0x6578, 0x20201); - WREG32(0x657C, 0x8F80BF08); - WREG32(0x6578, 0x20202); - WREG32(0x657C, 0xBFD081A0); - WREG32(0x6578, 0x20203); - WREG32(0x657C, 0xBFF88000); - WREG32(0x6578, 0x20300); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20301); - WREG32(0x657C, 0x8EE0BEC0); - WREG32(0x6578, 0x20302); - WREG32(0x657C, 0xBFB082A0); - WREG32(0x6578, 0x20303); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20400); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20401); - WREG32(0x657C, 0x8E00BEA0); - WREG32(0x6578, 0x20402); - WREG32(0x657C, 0xBF8883C0); - WREG32(0x6578, 0x20403); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x20500); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20501); - WREG32(0x657C, 0x8D00BE90); - WREG32(0x6578, 0x20502); - WREG32(0x657C, 0xBF588500); - WREG32(0x6578, 0x20503); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20600); - WREG32(0x657C, 0x80188000); - WREG32(0x6578, 0x20601); - WREG32(0x657C, 0x8BC0BE98); - WREG32(0x6578, 0x20602); - WREG32(0x657C, 0xBF308660); - WREG32(0x6578, 0x20603); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20700); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20701); - WREG32(0x657C, 0x8A80BEB0); - WREG32(0x6578, 0x20702); - WREG32(0x657C, 0xBF0087C0); - WREG32(0x6578, 0x20703); - WREG32(0x657C, 0x80008008); - WREG32(0x6578, 0x20800); - WREG32(0x657C, 0x80108000); - WREG32(0x6578, 0x20801); - WREG32(0x657C, 0x8920BED0); - WREG32(0x6578, 0x20802); - WREG32(0x657C, 0xBED08920); - WREG32(0x6578, 0x20803); - WREG32(0x657C, 0x80008010); - WREG32(0x6578, 0x30000); - WREG32(0x657C, 0x90008000); - WREG32(0x6578, 0x30001); - WREG32(0x657C, 0x80008000); - WREG32(0x6578, 0x30100); - WREG32(0x657C, 0x8FE0BF90); - WREG32(0x6578, 0x30101); - WREG32(0x657C, 0xBFF880A0); - WREG32(0x6578, 0x30200); - WREG32(0x657C, 0x8F60BF40); - WREG32(0x6578, 0x30201); - WREG32(0x657C, 0xBFE88180); - WREG32(0x6578, 0x30300); - WREG32(0x657C, 0x8EC0BF00); - WREG32(0x6578, 0x30301); - WREG32(0x657C, 0xBFC88280); - WREG32(0x6578, 0x30400); - WREG32(0x657C, 0x8DE0BEE0); - WREG32(0x6578, 0x30401); - WREG32(0x657C, 0xBFA083A0); - WREG32(0x6578, 0x30500); - WREG32(0x657C, 0x8CE0BED0); - WREG32(0x6578, 0x30501); - WREG32(0x657C, 0xBF7884E0); - WREG32(0x6578, 0x30600); - WREG32(0x657C, 0x8BA0BED8); - WREG32(0x6578, 0x30601); - WREG32(0x657C, 0xBF508640); - WREG32(0x6578, 0x30700); - WREG32(0x657C, 0x8A60BEE8); - WREG32(0x6578, 0x30701); - WREG32(0x657C, 0xBF2087A0); - WREG32(0x6578, 0x30800); - WREG32(0x657C, 0x8900BF00); - WREG32(0x6578, 0x30801); - WREG32(0x657C, 0xBF008900); -} - static void atombios_yuv_setup(struct drm_encoder *encoder, bool enable) { @@ -1073,129 +842,6 @@ atombios_yuv_setup(struct drm_encoder *encoder, bool enable) WREG32(reg, temp); } -static void -atombios_overscan_setup(struct drm_encoder *encoder, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc); - SET_CRTC_OVERSCAN_PS_ALLOCATION args; - int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan); - - memset(&args, 0, sizeof(args)); - - args.usOverscanRight = 0; - args.usOverscanLeft = 0; - args.usOverscanBottom = 0; - args.usOverscanTop = 0; - args.ucCRTC = radeon_crtc->crtc_id; - - if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type == RMX_FULL) { - args.usOverscanRight = 0; - args.usOverscanLeft = 0; - args.usOverscanBottom = 0; - args.usOverscanTop = 0; - } else if (radeon_encoder->rmx_type == RMX_CENTER) { - args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; - args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2; - args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; - args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2; - } else if (radeon_encoder->rmx_type == RMX_ASPECT) { - int a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay; - int a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay; - - if (a1 > a2) { - args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; - args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2; - } else if (a2 > a1) { - args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; - args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2; - } - } - } - - atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); - -} - -static void -atombios_scaler_setup(struct drm_encoder *encoder) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc); - ENABLE_SCALER_PS_ALLOCATION args; - int index = GetIndexIntoMasterTable(COMMAND, EnableScaler); - /* fixme - fill in enc_priv for atom dac */ - enum radeon_tv_std tv_std = TV_STD_NTSC; - - if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id) - return; - - memset(&args, 0, sizeof(args)); - - args.ucScaler = radeon_crtc->crtc_id; - - if (radeon_encoder->devices & (ATOM_DEVICE_TV_SUPPORT)) { - switch (tv_std) { - case TV_STD_NTSC: - default: - args.ucTVStandard = ATOM_TV_NTSC; - break; - case TV_STD_PAL: - args.ucTVStandard = ATOM_TV_PAL; - break; - case TV_STD_PAL_M: - args.ucTVStandard = ATOM_TV_PALM; - break; - case TV_STD_PAL_60: - args.ucTVStandard = ATOM_TV_PAL60; - break; - case TV_STD_NTSC_J: - args.ucTVStandard = ATOM_TV_NTSCJ; - break; - case TV_STD_SCART_PAL: - args.ucTVStandard = ATOM_TV_PAL; /* ??? */ - break; - case TV_STD_SECAM: - args.ucTVStandard = ATOM_TV_SECAM; - break; - case TV_STD_PAL_CN: - args.ucTVStandard = ATOM_TV_PALCN; - break; - } - args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; - } else if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT)) { - args.ucTVStandard = ATOM_TV_CV; - args.ucEnable = SCALER_ENABLE_MULTITAP_MODE; - } else if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type == RMX_FULL) - args.ucEnable = ATOM_SCALER_EXPANSION; - else if (radeon_encoder->rmx_type == RMX_CENTER) - args.ucEnable = ATOM_SCALER_CENTER; - else if (radeon_encoder->rmx_type == RMX_ASPECT) - args.ucEnable = ATOM_SCALER_EXPANSION; - } else { - if (ASIC_IS_AVIVO(rdev)) - args.ucEnable = ATOM_SCALER_DISABLE; - else - args.ucEnable = ATOM_SCALER_CENTER; - } - - atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args); - - if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT) - && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) { - atom_rv515_force_tv_scaler(rdev); - } - -} - static void radeon_atom_encoder_dpms(struct drm_encoder *encoder, int mode) { @@ -1448,8 +1094,6 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder, radeon_encoder->pixel_clock = adjusted_mode->clock; radeon_atombios_encoder_crtc_scratch_regs(encoder, radeon_crtc->crtc_id); - atombios_overscan_setup(encoder, mode, adjusted_mode); - atombios_scaler_setup(encoder); atombios_set_encoder_crtc_source(encoder); if (ASIC_IS_AVIVO(rdev)) { @@ -1667,6 +1311,7 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su radeon_encoder->encoder_id = encoder_id; radeon_encoder->devices = supported_device; + radeon_encoder->rmx_type = RMX_OFF; switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: @@ -1700,14 +1345,8 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1: case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2: - if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) { - radeon_encoder->rmx_type = RMX_FULL; - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS); - radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder); - } else { - drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); - radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); - } + drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS); + radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder); drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs); break; } diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 0613790e2a5b..7d06dc98a42a 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -29,6 +29,171 @@ #include "radeon_fixed.h" #include "radeon.h" +static void radeon_legacy_rmx_mode_set(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + int xres = mode->hdisplay; + int yres = mode->vdisplay; + bool hscale = true, vscale = true; + int hsync_wid; + int vsync_wid; + int hsync_start; + int blank_width; + u32 scale, inc, crtc_more_cntl; + u32 fp_horz_stretch, fp_vert_stretch, fp_horz_vert_active; + u32 fp_h_sync_strt_wid, fp_crtc_h_total_disp; + u32 fp_v_sync_strt_wid, fp_crtc_v_total_disp; + struct radeon_native_mode *native_mode = &radeon_crtc->native_mode; + + fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) & + (RADEON_VERT_STRETCH_RESERVED | + RADEON_VERT_AUTO_RATIO_INC); + fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) & + (RADEON_HORZ_FP_LOOP_STRETCH | + RADEON_HORZ_AUTO_RATIO_INC); + + crtc_more_cntl = 0; + if ((rdev->family == CHIP_RS100) || + (rdev->family == CHIP_RS200)) { + /* This is to workaround the asic bug for RMX, some versions + of BIOS dosen't have this register initialized correctly. */ + crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN; + } + + + fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff) + | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); + + hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; + if (!hsync_wid) + hsync_wid = 1; + hsync_start = mode->crtc_hsync_start - 8; + + fp_h_sync_strt_wid = ((hsync_start & 0x1fff) + | ((hsync_wid & 0x3f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NHSYNC) + ? RADEON_CRTC_H_SYNC_POL + : 0)); + + fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff) + | ((mode->crtc_vdisplay - 1) << 16)); + + vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; + if (!vsync_wid) + vsync_wid = 1; + + fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff) + | ((vsync_wid & 0x1f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NVSYNC) + ? RADEON_CRTC_V_SYNC_POL + : 0)); + + fp_horz_vert_active = 0; + + if (native_mode->panel_xres == 0 || + native_mode->panel_yres == 0) { + hscale = false; + vscale = false; + } else { + if (xres > native_mode->panel_xres) + xres = native_mode->panel_xres; + if (yres > native_mode->panel_yres) + yres = native_mode->panel_yres; + + if (xres == native_mode->panel_xres) + hscale = false; + if (yres == native_mode->panel_yres) + vscale = false; + } + + switch (radeon_crtc->rmx_type) { + case RMX_FULL: + case RMX_ASPECT: + if (!hscale) + fp_horz_stretch |= ((xres/8-1) << 16); + else { + inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0; + scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX) + / native_mode->panel_xres + 1; + fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) | + RADEON_HORZ_STRETCH_BLEND | + RADEON_HORZ_STRETCH_ENABLE | + ((native_mode->panel_xres/8-1) << 16)); + } + + if (!vscale) + fp_vert_stretch |= ((yres-1) << 12); + else { + inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0; + scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX) + / native_mode->panel_yres + 1; + fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) | + RADEON_VERT_STRETCH_ENABLE | + RADEON_VERT_STRETCH_BLEND | + ((native_mode->panel_yres-1) << 12)); + } + break; + case RMX_CENTER: + fp_horz_stretch |= ((xres/8-1) << 16); + fp_vert_stretch |= ((yres-1) << 12); + + crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN | + RADEON_CRTC_AUTO_VERT_CENTER_EN); + + blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8; + if (blank_width > 110) + blank_width = 110; + + fp_crtc_h_total_disp = (((blank_width) & 0x3ff) + | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); + + hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; + if (!hsync_wid) + hsync_wid = 1; + + fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff) + | ((hsync_wid & 0x3f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NHSYNC) + ? RADEON_CRTC_H_SYNC_POL + : 0)); + + fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff) + | ((mode->crtc_vdisplay - 1) << 16)); + + vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; + if (!vsync_wid) + vsync_wid = 1; + + fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff) + | ((vsync_wid & 0x1f) << 16) + | ((mode->flags & DRM_MODE_FLAG_NVSYNC) + ? RADEON_CRTC_V_SYNC_POL + : 0))); + + fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) | + (((native_mode->panel_xres / 8) & 0x1ff) << 16)); + break; + case RMX_OFF: + default: + fp_horz_stretch |= ((xres/8-1) << 16); + fp_vert_stretch |= ((yres-1) << 12); + break; + } + + WREG32(RADEON_FP_HORZ_STRETCH, fp_horz_stretch); + WREG32(RADEON_FP_VERT_STRETCH, fp_vert_stretch); + WREG32(RADEON_CRTC_MORE_CNTL, crtc_more_cntl); + WREG32(RADEON_FP_HORZ_VERT_ACTIVE, fp_horz_vert_active); + WREG32(RADEON_FP_H_SYNC_STRT_WID, fp_h_sync_strt_wid); + WREG32(RADEON_FP_V_SYNC_STRT_WID, fp_v_sync_strt_wid); + WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp); + WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp); +} + void radeon_restore_common_regs(struct drm_device *dev) { /* don't need this yet */ @@ -757,6 +922,8 @@ static bool radeon_crtc_mode_fixup(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode) { + if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode)) + return false; return true; } @@ -765,16 +932,25 @@ static int radeon_crtc_mode_set(struct drm_crtc *crtc, struct drm_display_mode *adjusted_mode, int x, int y, struct drm_framebuffer *old_fb) { - - DRM_DEBUG("\n"); + struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc); + struct drm_device *dev = crtc->dev; + struct radeon_device *rdev = dev->dev_private; /* TODO TV */ - radeon_crtc_set_base(crtc, x, y, old_fb); radeon_set_crtc_timing(crtc, adjusted_mode); radeon_set_pll(crtc, adjusted_mode); - radeon_init_disp_bandwidth(crtc->dev); - + radeon_bandwidth_update(rdev); + if (radeon_crtc->crtc_id == 0) { + radeon_legacy_rmx_mode_set(crtc, mode, adjusted_mode); + } else { + if (radeon_crtc->rmx_type != RMX_OFF) { + /* FIXME: only first crtc has rmx what should we + * do ? + */ + DRM_ERROR("Mode need scaling but only first crtc can do that.\n"); + } + } return 0; } @@ -805,478 +981,3 @@ void radeon_legacy_init_crtc(struct drm_device *dev, radeon_crtc->crtc_offset = RADEON_CRTC2_H_TOTAL_DISP - RADEON_CRTC_H_TOTAL_DISP; drm_crtc_helper_add(&radeon_crtc->base, &legacy_helper_funcs); } - -void radeon_init_disp_bw_legacy(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2) -{ - struct radeon_device *rdev = dev->dev_private; - fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff; - fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff; - fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff; - uint32_t temp, data, mem_trcd, mem_trp, mem_tras; - fixed20_12 memtcas_ff[8] = { - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(0), - fixed_init_half(1), - fixed_init_half(2), - fixed_init(0), - }; - fixed20_12 memtcas_rs480_ff[8] = { - fixed_init(0), - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(0), - fixed_init_half(1), - fixed_init_half(2), - fixed_init_half(3), - }; - fixed20_12 memtcas2_ff[8] = { - fixed_init(0), - fixed_init(1), - fixed_init(2), - fixed_init(3), - fixed_init(4), - fixed_init(5), - fixed_init(6), - fixed_init(7), - }; - fixed20_12 memtrbs[8] = { - fixed_init(1), - fixed_init_half(1), - fixed_init(2), - fixed_init_half(2), - fixed_init(3), - fixed_init_half(3), - fixed_init(4), - fixed_init_half(4) - }; - fixed20_12 memtrbs_r4xx[8] = { - fixed_init(4), - fixed_init(5), - fixed_init(6), - fixed_init(7), - fixed_init(8), - fixed_init(9), - fixed_init(10), - fixed_init(11) - }; - fixed20_12 min_mem_eff; - fixed20_12 mc_latency_sclk, mc_latency_mclk, k1; - fixed20_12 cur_latency_mclk, cur_latency_sclk; - fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate, - disp_drain_rate2, read_return_rate; - fixed20_12 time_disp1_drop_priority; - int c; - int cur_size = 16; /* in octawords */ - int critical_point = 0, critical_point2; -/* uint32_t read_return_rate, time_disp1_drop_priority; */ - int stop_req, max_stop_req; - - min_mem_eff.full = rfixed_const_8(0); - /* get modes */ - if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) { - uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER); - mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT); - mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT); - /* check crtc enables */ - if (mode2) - mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT); - if (mode1) - mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT); - WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer); - } - - /* - * determine is there is enough bw for current mode - */ - mclk_ff.full = rfixed_const(rdev->clock.default_mclk); - temp_ff.full = rfixed_const(100); - mclk_ff.full = rfixed_div(mclk_ff, temp_ff); - sclk_ff.full = rfixed_const(rdev->clock.default_sclk); - sclk_ff.full = rfixed_div(sclk_ff, temp_ff); - - temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1); - temp_ff.full = rfixed_const(temp); - mem_bw.full = rfixed_mul(mclk_ff, temp_ff); - - pix_clk.full = 0; - pix_clk2.full = 0; - peak_disp_bw.full = 0; - if (mode1) { - temp_ff.full = rfixed_const(1000); - pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */ - pix_clk.full = rfixed_div(pix_clk, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes1); - peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff); - } - if (mode2) { - temp_ff.full = rfixed_const(1000); - pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */ - pix_clk2.full = rfixed_div(pix_clk2, temp_ff); - temp_ff.full = rfixed_const(pixel_bytes2); - peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff); - } - - mem_bw.full = rfixed_mul(mem_bw, min_mem_eff); - if (peak_disp_bw.full >= mem_bw.full) { - DRM_ERROR("You may not have enough display bandwidth for current mode\n" - "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n"); - } - - /* Get values from the EXT_MEM_CNTL register...converting its contents. */ - temp = RREG32(RADEON_MEM_TIMING_CNTL); - if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */ - mem_trcd = ((temp >> 2) & 0x3) + 1; - mem_trp = ((temp & 0x3)) + 1; - mem_tras = ((temp & 0x70) >> 4) + 1; - } else if (rdev->family == CHIP_R300 || - rdev->family == CHIP_R350) { /* r300, r350 */ - mem_trcd = (temp & 0x7) + 1; - mem_trp = ((temp >> 8) & 0x7) + 1; - mem_tras = ((temp >> 11) & 0xf) + 4; - } else if (rdev->family == CHIP_RV350 || - rdev->family <= CHIP_RV380) { - /* rv3x0 */ - mem_trcd = (temp & 0x7) + 3; - mem_trp = ((temp >> 8) & 0x7) + 3; - mem_tras = ((temp >> 11) & 0xf) + 6; - } else if (rdev->family == CHIP_R420 || - rdev->family == CHIP_R423 || - rdev->family == CHIP_RV410) { - /* r4xx */ - mem_trcd = (temp & 0xf) + 3; - if (mem_trcd > 15) - mem_trcd = 15; - mem_trp = ((temp >> 8) & 0xf) + 3; - if (mem_trp > 15) - mem_trp = 15; - mem_tras = ((temp >> 12) & 0x1f) + 6; - if (mem_tras > 31) - mem_tras = 31; - } else { /* RV200, R200 */ - mem_trcd = (temp & 0x7) + 1; - mem_trp = ((temp >> 8) & 0x7) + 1; - mem_tras = ((temp >> 12) & 0xf) + 4; - } - /* convert to FF */ - trcd_ff.full = rfixed_const(mem_trcd); - trp_ff.full = rfixed_const(mem_trp); - tras_ff.full = rfixed_const(mem_tras); - - /* Get values from the MEM_SDRAM_MODE_REG register...converting its */ - temp = RREG32(RADEON_MEM_SDRAM_MODE_REG); - data = (temp & (7 << 20)) >> 20; - if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) { - if (rdev->family == CHIP_RS480) /* don't think rs400 */ - tcas_ff = memtcas_rs480_ff[data]; - else - tcas_ff = memtcas_ff[data]; - } else - tcas_ff = memtcas2_ff[data]; - - if (rdev->family == CHIP_RS400 || - rdev->family == CHIP_RS480) { - /* extra cas latency stored in bits 23-25 0-4 clocks */ - data = (temp >> 23) & 0x7; - if (data < 5) - tcas_ff.full += rfixed_const(data); - } - - if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) { - /* on the R300, Tcas is included in Trbs. - */ - temp = RREG32(RADEON_MEM_CNTL); - data = (R300_MEM_NUM_CHANNELS_MASK & temp); - if (data == 1) { - if (R300_MEM_USE_CD_CH_ONLY & temp) { - temp = RREG32(R300_MC_IND_INDEX); - temp &= ~R300_MC_IND_ADDR_MASK; - temp |= R300_MC_READ_CNTL_CD_mcind; - WREG32(R300_MC_IND_INDEX, temp); - temp = RREG32(R300_MC_IND_DATA); - data = (R300_MEM_RBS_POSITION_C_MASK & temp); - } else { - temp = RREG32(R300_MC_READ_CNTL_AB); - data = (R300_MEM_RBS_POSITION_A_MASK & temp); - } - } else { - temp = RREG32(R300_MC_READ_CNTL_AB); - data = (R300_MEM_RBS_POSITION_A_MASK & temp); - } - if (rdev->family == CHIP_RV410 || - rdev->family == CHIP_R420 || - rdev->family == CHIP_R423) - trbs_ff = memtrbs_r4xx[data]; - else - trbs_ff = memtrbs[data]; - tcas_ff.full += trbs_ff.full; - } - - sclk_eff_ff.full = sclk_ff.full; - - if (rdev->flags & RADEON_IS_AGP) { - fixed20_12 agpmode_ff; - agpmode_ff.full = rfixed_const(radeon_agpmode); - temp_ff.full = rfixed_const_666(16); - sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff); - } - /* TODO PCIE lanes may affect this - agpmode == 16?? */ - - if (ASIC_IS_R300(rdev)) { - sclk_delay_ff.full = rfixed_const(250); - } else { - if ((rdev->family == CHIP_RV100) || - rdev->flags & RADEON_IS_IGP) { - if (rdev->mc.vram_is_ddr) - sclk_delay_ff.full = rfixed_const(41); - else - sclk_delay_ff.full = rfixed_const(33); - } else { - if (rdev->mc.vram_width == 128) - sclk_delay_ff.full = rfixed_const(57); - else - sclk_delay_ff.full = rfixed_const(41); - } - } - - mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff); - - if (rdev->mc.vram_is_ddr) { - if (rdev->mc.vram_width == 32) { - k1.full = rfixed_const(40); - c = 3; - } else { - k1.full = rfixed_const(20); - c = 1; - } - } else { - k1.full = rfixed_const(40); - c = 3; - } - - temp_ff.full = rfixed_const(2); - mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff); - temp_ff.full = rfixed_const(c); - mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff); - temp_ff.full = rfixed_const(4); - mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff); - mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff); - mc_latency_mclk.full += k1.full; - - mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff); - mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff); - - /* - HW cursor time assuming worst case of full size colour cursor. - */ - temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1)))); - temp_ff.full += trcd_ff.full; - if (temp_ff.full < tras_ff.full) - temp_ff.full = tras_ff.full; - cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff); - - temp_ff.full = rfixed_const(cur_size); - cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff); - /* - Find the total latency for the display data. - */ - disp_latency_overhead.full = rfixed_const(80); - disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff); - mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full; - mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full; - - if (mc_latency_mclk.full > mc_latency_sclk.full) - disp_latency.full = mc_latency_mclk.full; - else - disp_latency.full = mc_latency_sclk.full; - - /* setup Max GRPH_STOP_REQ default value */ - if (ASIC_IS_RV100(rdev)) - max_stop_req = 0x5c; - else - max_stop_req = 0x7c; - - if (mode1) { - /* CRTC1 - Set GRPH_BUFFER_CNTL register using h/w defined optimal values. - GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ] - */ - stop_req = mode1->hdisplay * pixel_bytes1 / 16; - - if (stop_req > max_stop_req) - stop_req = max_stop_req; - - /* - Find the drain rate of the display buffer. - */ - temp_ff.full = rfixed_const((16/pixel_bytes1)); - disp_drain_rate.full = rfixed_div(pix_clk, temp_ff); - - /* - Find the critical point of the display buffer. - */ - crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency); - crit_point_ff.full += rfixed_const_half(0); - - critical_point = rfixed_trunc(crit_point_ff); - - if (rdev->disp_priority == 2) { - critical_point = 0; - } - - /* - The critical point should never be above max_stop_req-4. Setting - GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time. - */ - if (max_stop_req - critical_point < 4) - critical_point = 0; - - if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) { - /* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/ - critical_point = 0x10; - } - - temp = RREG32(RADEON_GRPH_BUFFER_CNTL); - temp &= ~(RADEON_GRPH_STOP_REQ_MASK); - temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); - temp &= ~(RADEON_GRPH_START_REQ_MASK); - if ((rdev->family == CHIP_R350) && - (stop_req > 0x15)) { - stop_req -= 0x10; - } - temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); - temp |= RADEON_GRPH_BUFFER_SIZE; - temp &= ~(RADEON_GRPH_CRITICAL_CNTL | - RADEON_GRPH_CRITICAL_AT_SOF | - RADEON_GRPH_STOP_CNTL); - /* - Write the result into the register. - */ - WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) | - (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT))); - -#if 0 - if ((rdev->family == CHIP_RS400) || - (rdev->family == CHIP_RS480)) { - /* attempt to program RS400 disp regs correctly ??? */ - temp = RREG32(RS400_DISP1_REG_CNTL); - temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK | - RS400_DISP1_STOP_REQ_LEVEL_MASK); - WREG32(RS400_DISP1_REQ_CNTL1, (temp | - (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) | - (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); - temp = RREG32(RS400_DMIF_MEM_CNTL1); - temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK | - RS400_DISP1_CRITICAL_POINT_STOP_MASK); - WREG32(RS400_DMIF_MEM_CNTL1, (temp | - (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) | - (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT))); - } -#endif - - DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n", - /* (unsigned int)info->SavedReg->grph_buffer_cntl, */ - (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL)); - } - - if (mode2) { - u32 grph2_cntl; - stop_req = mode2->hdisplay * pixel_bytes2 / 16; - - if (stop_req > max_stop_req) - stop_req = max_stop_req; - - /* - Find the drain rate of the display buffer. - */ - temp_ff.full = rfixed_const((16/pixel_bytes2)); - disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff); - - grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL); - grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK); - grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT); - grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK); - if ((rdev->family == CHIP_R350) && - (stop_req > 0x15)) { - stop_req -= 0x10; - } - grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT); - grph2_cntl |= RADEON_GRPH_BUFFER_SIZE; - grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL | - RADEON_GRPH_CRITICAL_AT_SOF | - RADEON_GRPH_STOP_CNTL); - - if ((rdev->family == CHIP_RS100) || - (rdev->family == CHIP_RS200)) - critical_point2 = 0; - else { - temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128; - temp_ff.full = rfixed_const(temp); - temp_ff.full = rfixed_mul(mclk_ff, temp_ff); - if (sclk_ff.full < temp_ff.full) - temp_ff.full = sclk_ff.full; - - read_return_rate.full = temp_ff.full; - - if (mode1) { - temp_ff.full = read_return_rate.full - disp_drain_rate.full; - time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff); - } else { - time_disp1_drop_priority.full = 0; - } - crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full; - crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2); - crit_point_ff.full += rfixed_const_half(0); - - critical_point2 = rfixed_trunc(crit_point_ff); - - if (rdev->disp_priority == 2) { - critical_point2 = 0; - } - - if (max_stop_req - critical_point2 < 4) - critical_point2 = 0; - - } - - if (critical_point2 == 0 && rdev->family == CHIP_R300) { - /* some R300 cards have problem with this set to 0 */ - critical_point2 = 0x10; - } - - WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) | - (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT))); - - if ((rdev->family == CHIP_RS400) || - (rdev->family == CHIP_RS480)) { -#if 0 - /* attempt to program RS400 disp2 regs correctly ??? */ - temp = RREG32(RS400_DISP2_REQ_CNTL1); - temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK | - RS400_DISP2_STOP_REQ_LEVEL_MASK); - WREG32(RS400_DISP2_REQ_CNTL1, (temp | - (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) | - (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT))); - temp = RREG32(RS400_DISP2_REQ_CNTL2); - temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK | - RS400_DISP2_CRITICAL_POINT_STOP_MASK); - WREG32(RS400_DISP2_REQ_CNTL2, (temp | - (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) | - (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT))); -#endif - WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC); - WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000); - WREG32(RS400_DMIF_MEM_CNTL1, 0x29CA71DC); - WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC); - } - - DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n", - (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL)); - } -} diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c index 2c2f42de1d4c..34d0f58eb944 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c @@ -30,170 +30,6 @@ #include "atom.h" -static void radeon_legacy_rmx_mode_set(struct drm_encoder *encoder, - struct drm_display_mode *mode, - struct drm_display_mode *adjusted_mode) -{ - struct drm_device *dev = encoder->dev; - struct radeon_device *rdev = dev->dev_private; - struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder); - int xres = mode->hdisplay; - int yres = mode->vdisplay; - bool hscale = true, vscale = true; - int hsync_wid; - int vsync_wid; - int hsync_start; - uint32_t scale, inc; - uint32_t fp_horz_stretch, fp_vert_stretch, crtc_more_cntl, fp_horz_vert_active; - uint32_t fp_h_sync_strt_wid, fp_v_sync_strt_wid, fp_crtc_h_total_disp, fp_crtc_v_total_disp; - struct radeon_native_mode *native_mode = &radeon_encoder->native_mode; - - DRM_DEBUG("\n"); - - fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) & - (RADEON_VERT_STRETCH_RESERVED | - RADEON_VERT_AUTO_RATIO_INC); - fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) & - (RADEON_HORZ_FP_LOOP_STRETCH | - RADEON_HORZ_AUTO_RATIO_INC); - - crtc_more_cntl = 0; - if ((rdev->family == CHIP_RS100) || - (rdev->family == CHIP_RS200)) { - /* This is to workaround the asic bug for RMX, some versions - of BIOS dosen't have this register initialized correctly. */ - crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN; - } - - - fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff) - | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); - - hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; - if (!hsync_wid) - hsync_wid = 1; - hsync_start = mode->crtc_hsync_start - 8; - - fp_h_sync_strt_wid = ((hsync_start & 0x1fff) - | ((hsync_wid & 0x3f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NHSYNC) - ? RADEON_CRTC_H_SYNC_POL - : 0)); - - fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff) - | ((mode->crtc_vdisplay - 1) << 16)); - - vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; - if (!vsync_wid) - vsync_wid = 1; - - fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff) - | ((vsync_wid & 0x1f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NVSYNC) - ? RADEON_CRTC_V_SYNC_POL - : 0)); - - fp_horz_vert_active = 0; - - if (native_mode->panel_xres == 0 || - native_mode->panel_yres == 0) { - hscale = false; - vscale = false; - } else { - if (xres > native_mode->panel_xres) - xres = native_mode->panel_xres; - if (yres > native_mode->panel_yres) - yres = native_mode->panel_yres; - - if (xres == native_mode->panel_xres) - hscale = false; - if (yres == native_mode->panel_yres) - vscale = false; - } - - if (radeon_encoder->flags & RADEON_USE_RMX) { - if (radeon_encoder->rmx_type != RMX_CENTER) { - if (!hscale) - fp_horz_stretch |= ((xres/8-1) << 16); - else { - inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0; - scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX) - / native_mode->panel_xres + 1; - fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) | - RADEON_HORZ_STRETCH_BLEND | - RADEON_HORZ_STRETCH_ENABLE | - ((native_mode->panel_xres/8-1) << 16)); - } - - if (!vscale) - fp_vert_stretch |= ((yres-1) << 12); - else { - inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0; - scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX) - / native_mode->panel_yres + 1; - fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) | - RADEON_VERT_STRETCH_ENABLE | - RADEON_VERT_STRETCH_BLEND | - ((native_mode->panel_yres-1) << 12)); - } - } else if (radeon_encoder->rmx_type == RMX_CENTER) { - int blank_width; - - fp_horz_stretch |= ((xres/8-1) << 16); - fp_vert_stretch |= ((yres-1) << 12); - - crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN | - RADEON_CRTC_AUTO_VERT_CENTER_EN); - - blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8; - if (blank_width > 110) - blank_width = 110; - - fp_crtc_h_total_disp = (((blank_width) & 0x3ff) - | ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16)); - - hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8; - if (!hsync_wid) - hsync_wid = 1; - - fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff) - | ((hsync_wid & 0x3f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NHSYNC) - ? RADEON_CRTC_H_SYNC_POL - : 0)); - - fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff) - | ((mode->crtc_vdisplay - 1) << 16)); - - vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start; - if (!vsync_wid) - vsync_wid = 1; - - fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff) - | ((vsync_wid & 0x1f) << 16) - | ((mode->flags & DRM_MODE_FLAG_NVSYNC) - ? RADEON_CRTC_V_SYNC_POL - : 0))); - - fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) | - (((native_mode->panel_xres / 8) & 0x1ff) << 16)); - } - } else { - fp_horz_stretch |= ((xres/8-1) << 16); - fp_vert_stretch |= ((yres-1) << 12); - } - - WREG32(RADEON_FP_HORZ_STRETCH, fp_horz_stretch); - WREG32(RADEON_FP_VERT_STRETCH, fp_vert_stretch); - WREG32(RADEON_CRTC_MORE_CNTL, crtc_more_cntl); - WREG32(RADEON_FP_HORZ_VERT_ACTIVE, fp_horz_vert_active); - WREG32(RADEON_FP_H_SYNC_STRT_WID, fp_h_sync_strt_wid); - WREG32(RADEON_FP_V_SYNC_STRT_WID, fp_v_sync_strt_wid); - WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp); - WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp); - -} - static void radeon_legacy_lvds_dpms(struct drm_encoder *encoder, int mode) { struct drm_device *dev = encoder->dev; @@ -287,9 +123,6 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - lvds_pll_cntl = RREG32(RADEON_LVDS_PLL_CNTL); lvds_pll_cntl &= ~RADEON_LVDS_PLL_EN; @@ -318,7 +151,7 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if (ASIC_IS_R300(rdev)) { - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) lvds_pll_cntl |= R300_LVDS_SRC_SEL_RMX; } else lvds_gen_cntl &= ~RADEON_LVDS_SEL_CRTC2; @@ -350,8 +183,6 @@ static bool radeon_legacy_lvds_mode_fixup(struct drm_encoder *encoder, drm_mode_set_crtcinfo(adjusted_mode, 0); - radeon_encoder->flags &= ~RADEON_USE_RMX; - if (radeon_encoder->rmx_type != RMX_OFF) radeon_rmx_mode_fixup(encoder, mode, adjusted_mode); @@ -455,9 +286,6 @@ static void radeon_legacy_primary_dac_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (radeon_crtc->crtc_id == 0) { if (rdev->family == CHIP_R200 || ASIC_IS_R300(rdev)) { disp_output_cntl = RREG32(RADEON_DISP_OUTPUT_CNTL) & @@ -653,9 +481,6 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - tmp = tmds_pll_cntl = RREG32(RADEON_TMDS_PLL_CNTL); tmp &= 0xfffff; if (rdev->family == CHIP_RV280) { @@ -711,7 +536,7 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if (ASIC_IS_R300(rdev) || rdev->family == CHIP_R200) { fp_gen_cntl &= ~R200_FP_SOURCE_SEL_MASK; - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) fp_gen_cntl |= R200_FP_SOURCE_SEL_RMX; else fp_gen_cntl |= R200_FP_SOURCE_SEL_CRTC1; @@ -820,9 +645,6 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (rdev->is_atom_bios) { radeon_encoder->pixel_clock = adjusted_mode->clock; atombios_external_tmds_setup(encoder, ATOM_ENABLE); @@ -856,7 +678,7 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder, if (radeon_crtc->crtc_id == 0) { if ((rdev->family == CHIP_R200) || ASIC_IS_R300(rdev)) { fp2_gen_cntl &= ~R200_FP2_SOURCE_SEL_MASK; - if (radeon_encoder->flags & RADEON_USE_RMX) + if (radeon_encoder->rmx_type != RMX_OFF) fp2_gen_cntl |= R200_FP2_SOURCE_SEL_RMX; else fp2_gen_cntl |= R200_FP2_SOURCE_SEL_CRTC1; @@ -1014,9 +836,6 @@ static void radeon_legacy_tv_dac_mode_set(struct drm_encoder *encoder, DRM_DEBUG("\n"); - if (radeon_crtc->crtc_id == 0) - radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode); - if (rdev->family != CHIP_R200) { tv_dac_cntl = RREG32(RADEON_TV_DAC_CNTL); if (rdev->family == CHIP_R420 || @@ -1243,6 +1062,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t radeon_encoder->encoder_id = encoder_id; radeon_encoder->devices = supported_device; + radeon_encoder->rmx_type = RMX_OFF; switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h index ba89b59f6e50..3b09a1f2d8f9 100644 --- a/drivers/gpu/drm/radeon/radeon_mode.h +++ b/drivers/gpu/drm/radeon/radeon_mode.h @@ -36,6 +36,9 @@ #include #include #include +#include "radeon_fixed.h" + +struct radeon_device; #define to_radeon_crtc(x) container_of(x, struct radeon_crtc, base) #define to_radeon_connector(x) container_of(x, struct radeon_connector, base) @@ -171,6 +174,18 @@ struct radeon_mode_info { struct atom_context *atom_context; enum radeon_connector_table connector_table; bool mode_config_initialized; + struct radeon_crtc *crtcs[2]; +}; + +struct radeon_native_mode { + /* preferred mode */ + uint32_t panel_xres, panel_yres; + uint32_t hoverplus, hsync_width; + uint32_t hblank; + uint32_t voverplus, vsync_width; + uint32_t vblank; + uint32_t dotclock; + uint32_t flags; }; struct radeon_crtc { @@ -188,19 +203,11 @@ struct radeon_crtc { int cursor_height; uint32_t legacy_display_base_addr; uint32_t legacy_cursor_offset; -}; - -#define RADEON_USE_RMX 1 - -struct radeon_native_mode { - /* preferred mode */ - uint32_t panel_xres, panel_yres; - uint32_t hoverplus, hsync_width; - uint32_t hblank; - uint32_t voverplus, vsync_width; - uint32_t vblank; - uint32_t dotclock; - uint32_t flags; + enum radeon_rmx_type rmx_type; + uint32_t devices; + fixed20_12 vsc; + fixed20_12 hsc; + struct radeon_native_mode native_mode; }; struct radeon_encoder_primary_dac { @@ -386,16 +393,9 @@ void radeon_enc_destroy(struct drm_encoder *encoder); void radeon_copy_fb(struct drm_device *dev, struct drm_gem_object *dst_obj); void radeon_combios_asic_init(struct drm_device *dev); extern int radeon_static_clocks_init(struct drm_device *dev); -void radeon_init_disp_bw_legacy(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2); -void radeon_init_disp_bw_avivo(struct drm_device *dev, - struct drm_display_mode *mode1, - uint32_t pixel_bytes1, - struct drm_display_mode *mode2, - uint32_t pixel_bytes2); -void radeon_init_disp_bandwidth(struct drm_device *dev); +bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode); +void atom_rv515_force_tv_scaler(struct radeon_device *rdev); #endif diff --git a/drivers/gpu/drm/radeon/radeon_share.h b/drivers/gpu/drm/radeon/radeon_share.h new file mode 100644 index 000000000000..63a773578f17 --- /dev/null +++ b/drivers/gpu/drm/radeon/radeon_share.h @@ -0,0 +1,39 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef __RADEON_SHARE_H__ +#define __RADEON_SHARE_H__ + +void r100_vram_init_sizes(struct radeon_device *rdev); + +void rs690_line_buffer_adjust(struct radeon_device *rdev, + struct drm_display_mode *mode1, + struct drm_display_mode *mode2); + +void rv515_bandwidth_avivo_update(struct radeon_device *rdev); + +#endif diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index daf24e85cba3..96a3c8486d25 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -29,6 +29,7 @@ #include #include "radeon_reg.h" #include "radeon.h" +#include "radeon_share.h" /* rs400,rs480 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index ab0c967553e6..bccdce7fd379 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -301,6 +301,11 @@ void rs600_vram_info(struct radeon_device *rdev) rdev->mc.vram_width = 128; } +void rs600_bandwidth_update(struct radeon_device *rdev) +{ + /* FIXME: implement, should this be like rs690 ? */ +} + /* * Indirect registers accessor diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 79ba85042b5f..97eaee3d28b8 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -28,6 +28,9 @@ #include "drmP.h" #include "radeon_reg.h" #include "radeon.h" +#include "rs690r.h" +#include "atom.h" +#include "atom-bits.h" /* rs690,rs740 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -138,9 +141,82 @@ void rs690_gpu_init(struct radeon_device *rdev) /* * VRAM info. */ +void rs690_pm_info(struct radeon_device *rdev) +{ + int index = GetIndexIntoMasterTable(DATA, IntegratedSystemInfo); + struct _ATOM_INTEGRATED_SYSTEM_INFO *info; + struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *info_v2; + void *ptr; + uint16_t data_offset; + uint8_t frev, crev; + fixed20_12 tmp; + + atom_parse_data_header(rdev->mode_info.atom_context, index, NULL, + &frev, &crev, &data_offset); + ptr = rdev->mode_info.atom_context->bios + data_offset; + info = (struct _ATOM_INTEGRATED_SYSTEM_INFO *)ptr; + info_v2 = (struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *)ptr; + /* Get various system informations from bios */ + switch (crev) { + case 1: + tmp.full = rfixed_const(100); + rdev->pm.igp_sideport_mclk.full = rfixed_const(info->ulBootUpMemoryClock); + rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp); + rdev->pm.igp_system_mclk.full = rfixed_const(le16_to_cpu(info->usK8MemoryClock)); + rdev->pm.igp_ht_link_clk.full = rfixed_const(le16_to_cpu(info->usFSBClock)); + rdev->pm.igp_ht_link_width.full = rfixed_const(info->ucHTLinkWidth); + break; + case 2: + tmp.full = rfixed_const(100); + rdev->pm.igp_sideport_mclk.full = rfixed_const(info_v2->ulBootUpSidePortClock); + rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp); + rdev->pm.igp_system_mclk.full = rfixed_const(info_v2->ulBootUpUMAClock); + rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp); + rdev->pm.igp_ht_link_clk.full = rfixed_const(info_v2->ulHTLinkFreq); + rdev->pm.igp_ht_link_clk.full = rfixed_div(rdev->pm.igp_ht_link_clk, tmp); + rdev->pm.igp_ht_link_width.full = rfixed_const(le16_to_cpu(info_v2->usMinHTLinkWidth)); + break; + default: + tmp.full = rfixed_const(100); + /* We assume the slower possible clock ie worst case */ + /* DDR 333Mhz */ + rdev->pm.igp_sideport_mclk.full = rfixed_const(333); + /* FIXME: system clock ? */ + rdev->pm.igp_system_mclk.full = rfixed_const(100); + rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp); + rdev->pm.igp_ht_link_clk.full = rfixed_const(200); + rdev->pm.igp_ht_link_width.full = rfixed_const(8); + DRM_ERROR("No integrated system info for your GPU, using safe default\n"); + break; + } + /* Compute various bandwidth */ + /* k8_bandwidth = (memory_clk / 2) * 2 * 8 * 0.5 = memory_clk * 4 */ + tmp.full = rfixed_const(4); + rdev->pm.k8_bandwidth.full = rfixed_mul(rdev->pm.igp_system_mclk, tmp); + /* ht_bandwidth = ht_clk * 2 * ht_width / 8 * 0.8 + * = ht_clk * ht_width / 5 + */ + tmp.full = rfixed_const(5); + rdev->pm.ht_bandwidth.full = rfixed_mul(rdev->pm.igp_ht_link_clk, + rdev->pm.igp_ht_link_width); + rdev->pm.ht_bandwidth.full = rfixed_div(rdev->pm.ht_bandwidth, tmp); + if (tmp.full < rdev->pm.max_bandwidth.full) { + /* HT link is a limiting factor */ + rdev->pm.max_bandwidth.full = tmp.full; + } + /* sideport_bandwidth = (sideport_clk / 2) * 2 * 2 * 0.7 + * = (sideport_clk * 14) / 10 + */ + tmp.full = rfixed_const(14); + rdev->pm.sideport_bandwidth.full = rfixed_mul(rdev->pm.igp_sideport_mclk, tmp); + tmp.full = rfixed_const(10); + rdev->pm.sideport_bandwidth.full = rfixed_div(rdev->pm.sideport_bandwidth, tmp); +} + void rs690_vram_info(struct radeon_device *rdev) { uint32_t tmp; + fixed20_12 a; rs400_gart_adjust_size(rdev); /* DDR for all card after R300 & IGP */ @@ -156,8 +232,404 @@ void rs690_vram_info(struct radeon_device *rdev) rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + rs690_pm_info(rdev); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); + a.full = rfixed_const(16); + /* core_bandwidth = sclk(Mhz) * 16 */ + rdev->pm.core_bandwidth.full = rfixed_div(rdev->pm.sclk, a); +} + +void rs690_line_buffer_adjust(struct radeon_device *rdev, + struct drm_display_mode *mode1, + struct drm_display_mode *mode2) +{ + u32 tmp; + + /* + * Line Buffer Setup + * There is a single line buffer shared by both display controllers. + * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between + * the display controllers. The paritioning can either be done + * manually or via one of four preset allocations specified in bits 1:0: + * 0 - line buffer is divided in half and shared between crtc + * 1 - D1 gets 3/4 of the line buffer, D2 gets 1/4 + * 2 - D1 gets the whole buffer + * 3 - D1 gets 1/4 of the line buffer, D2 gets 3/4 + * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual + * allocation mode. In manual allocation mode, D1 always starts at 0, + * D1 end/2 is specified in bits 14:4; D2 allocation follows D1. + */ + tmp = RREG32(DC_LB_MEMORY_SPLIT) & ~DC_LB_MEMORY_SPLIT_MASK; + tmp &= ~DC_LB_MEMORY_SPLIT_SHIFT_MODE; + /* auto */ + if (mode1 && mode2) { + if (mode1->hdisplay > mode2->hdisplay) { + if (mode1->hdisplay > 2560) + tmp |= DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q; + else + tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else if (mode2->hdisplay > mode1->hdisplay) { + if (mode2->hdisplay > 2560) + tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; + else + tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else + tmp |= AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF; + } else if (mode1) { + tmp |= DC_LB_MEMORY_SPLIT_D1_ONLY; + } else if (mode2) { + tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q; + } + WREG32(DC_LB_MEMORY_SPLIT, tmp); } +struct rs690_watermark { + u32 lb_request_fifo_depth; + fixed20_12 num_line_pair; + fixed20_12 estimated_width; + fixed20_12 worst_case_latency; + fixed20_12 consumption_rate; + fixed20_12 active_time; + fixed20_12 dbpp; + fixed20_12 priority_mark_max; + fixed20_12 priority_mark; + fixed20_12 sclk; +}; + +void rs690_crtc_bandwidth_compute(struct radeon_device *rdev, + struct radeon_crtc *crtc, + struct rs690_watermark *wm) +{ + struct drm_display_mode *mode = &crtc->base.mode; + fixed20_12 a, b, c; + fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width; + fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency; + /* FIXME: detect IGP with sideport memory, i don't think there is any + * such product available + */ + bool sideport = false; + + if (!crtc->base.enabled) { + /* FIXME: wouldn't it better to set priority mark to maximum */ + wm->lb_request_fifo_depth = 4; + return; + } + + if (crtc->vsc.full > rfixed_const(2)) + wm->num_line_pair.full = rfixed_const(2); + else + wm->num_line_pair.full = rfixed_const(1); + + b.full = rfixed_const(mode->crtc_hdisplay); + c.full = rfixed_const(256); + a.full = rfixed_mul(wm->num_line_pair, b); + request_fifo_depth.full = rfixed_div(a, c); + if (a.full < rfixed_const(4)) { + wm->lb_request_fifo_depth = 4; + } else { + wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth); + } + + /* Determine consumption rate + * pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000) + * vtaps = number of vertical taps, + * vsc = vertical scaling ratio, defined as source/destination + * hsc = horizontal scaling ration, defined as source/destination + */ + a.full = rfixed_const(mode->clock); + b.full = rfixed_const(1000); + a.full = rfixed_div(a, b); + pclk.full = rfixed_div(b, a); + if (crtc->rmx_type != RMX_OFF) { + b.full = rfixed_const(2); + if (crtc->vsc.full > b.full) + b.full = crtc->vsc.full; + b.full = rfixed_mul(b, crtc->hsc); + c.full = rfixed_const(2); + b.full = rfixed_div(b, c); + consumption_time.full = rfixed_div(pclk, b); + } else { + consumption_time.full = pclk.full; + } + a.full = rfixed_const(1); + wm->consumption_rate.full = rfixed_div(a, consumption_time); + + + /* Determine line time + * LineTime = total time for one line of displayhtotal + * LineTime = total number of horizontal pixels + * pclk = pixel clock period(ns) + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + line_time.full = rfixed_mul(a, pclk); + + /* Determine active time + * ActiveTime = time of active region of display within one line, + * hactive = total number of horizontal active pixels + * htotal = total number of horizontal pixels + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + b.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->active_time.full = rfixed_mul(line_time, b); + wm->active_time.full = rfixed_div(wm->active_time, a); + + /* Maximun bandwidth is the minimun bandwidth of all component */ + rdev->pm.max_bandwidth = rdev->pm.core_bandwidth; + if (sideport) { + if (rdev->pm.max_bandwidth.full > rdev->pm.sideport_bandwidth.full && + rdev->pm.sideport_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.sideport_bandwidth; + read_delay_latency.full = rfixed_const(370 * 800 * 1000); + read_delay_latency.full = rfixed_div(read_delay_latency, + rdev->pm.igp_sideport_mclk); + } else { + if (rdev->pm.max_bandwidth.full > rdev->pm.k8_bandwidth.full && + rdev->pm.k8_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.k8_bandwidth; + if (rdev->pm.max_bandwidth.full > rdev->pm.ht_bandwidth.full && + rdev->pm.ht_bandwidth.full) + rdev->pm.max_bandwidth = rdev->pm.ht_bandwidth; + read_delay_latency.full = rfixed_const(5000); + } + + /* sclk = system clocks(ns) = 1000 / max_bandwidth / 16 */ + a.full = rfixed_const(16); + rdev->pm.sclk.full = rfixed_mul(rdev->pm.max_bandwidth, a); + a.full = rfixed_const(1000); + rdev->pm.sclk.full = rfixed_div(a, rdev->pm.sclk); + /* Determine chunk time + * ChunkTime = the time it takes the DCP to send one chunk of data + * to the LB which consists of pipeline delay and inter chunk gap + * sclk = system clock(ns) + */ + a.full = rfixed_const(256 * 13); + chunk_time.full = rfixed_mul(rdev->pm.sclk, a); + a.full = rfixed_const(10); + chunk_time.full = rfixed_div(chunk_time, a); + + /* Determine the worst case latency + * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines) + * WorstCaseLatency = worst case time from urgent to when the MC starts + * to return data + * READ_DELAY_IDLE_MAX = constant of 1us + * ChunkTime = time it takes the DCP to send one chunk of data to the LB + * which consists of pipeline delay and inter chunk gap + */ + if (rfixed_trunc(wm->num_line_pair) > 1) { + a.full = rfixed_const(3); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } else { + a.full = rfixed_const(2); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } + + /* Determine the tolerable latency + * TolerableLatency = Any given request has only 1 line time + * for the data to be returned + * LBRequestFifoDepth = Number of chunk requests the LB can + * put into the request FIFO for a display + * LineTime = total time for one line of display + * ChunkTime = the time it takes the DCP to send one chunk + * of data to the LB which consists of + * pipeline delay and inter chunk gap + */ + if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) { + tolerable_latency.full = line_time.full; + } else { + tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2); + tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full; + tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time); + tolerable_latency.full = line_time.full - tolerable_latency.full; + } + /* We assume worst case 32bits (4 bytes) */ + wm->dbpp.full = rfixed_const(4 * 8); + + /* Determine the maximum priority mark + * width = viewport width in pixels + */ + a.full = rfixed_const(16); + wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a); + + /* Determine estimated width */ + estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full; + estimated_width.full = rfixed_div(estimated_width, consumption_time); + if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) { + wm->priority_mark.full = rfixed_const(10); + } else { + a.full = rfixed_const(16); + wm->priority_mark.full = rfixed_div(estimated_width, a); + wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full; + } +} + +void rs690_bandwidth_update(struct radeon_device *rdev) +{ + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + struct rs690_watermark wm0; + struct rs690_watermark wm1; + u32 tmp; + fixed20_12 priority_mark02, priority_mark12, fill_rate; + fixed20_12 a, b; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + /* + * Set display0/1 priority up in the memory controller for + * modes if the user specifies HIGH for displaypriority + * option. + */ + if (rdev->disp_priority == 2) { + tmp = RREG32_MC(MC_INIT_MISC_LAT_TIMER); + tmp &= ~MC_DISP1R_INIT_LAT_MASK; + tmp &= ~MC_DISP0R_INIT_LAT_MASK; + if (mode1) + tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT); + if (mode0) + tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT); + WREG32_MC(MC_INIT_MISC_LAT_TIMER, tmp); + } + rs690_line_buffer_adjust(rdev, mode0, mode1); + + if ((rdev->family == CHIP_RS690) || (rdev->family == CHIP_RS740)) + WREG32(DCP_CONTROL, 0); + if ((rdev->family == CHIP_RS780) || (rdev->family == CHIP_RS880)) + WREG32(DCP_CONTROL, 2); + + rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0); + rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1); + + tmp = (wm0.lb_request_fifo_depth - 1); + tmp |= (wm1.lb_request_fifo_depth - 1) << 16; + WREG32(LB_MAX_REQ_OUTSTANDING, tmp); + + if (mode0 && mode1) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + if (rfixed_trunc(wm1.dbpp) > 64) + b.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair); + else + b.full = wm1.num_line_pair.full; + a.full += b.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } else if (mode0) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + } else { + if (rfixed_trunc(wm1.dbpp) > 64) + a.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair); + else + a.full = wm1.num_line_pair.full; + fill_rate.full = rfixed_div(wm1.sclk, a); + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + a.full = a.full + b.full; + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } +} /* * Indirect registers accessor diff --git a/drivers/gpu/drm/radeon/rs690r.h b/drivers/gpu/drm/radeon/rs690r.h new file mode 100644 index 000000000000..c0d9faa2175b --- /dev/null +++ b/drivers/gpu/drm/radeon/rs690r.h @@ -0,0 +1,99 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef RS690R_H +#define RS690R_H + +/* RS690/RS740 registers */ +#define MC_INDEX 0x0078 +# define MC_INDEX_MASK 0x1FF +# define MC_INDEX_WR_EN (1 << 9) +# define MC_INDEX_WR_ACK 0x7F +#define MC_DATA 0x007C +#define HDP_FB_LOCATION 0x0134 +#define DC_LB_MEMORY_SPLIT 0x6520 +#define DC_LB_MEMORY_SPLIT_MASK 0x00000003 +#define DC_LB_MEMORY_SPLIT_SHIFT 0 +#define DC_LB_MEMORY_SPLIT_D1HALF_D2HALF 0 +#define DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q 1 +#define DC_LB_MEMORY_SPLIT_D1_ONLY 2 +#define DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q 3 +#define DC_LB_MEMORY_SPLIT_SHIFT_MODE (1 << 2) +#define DC_LB_DISP1_END_ADR_SHIFT 4 +#define DC_LB_DISP1_END_ADR_MASK 0x00007FF0 +#define D1MODE_PRIORITY_A_CNT 0x6548 +#define MODE_PRIORITY_MARK_MASK 0x00007FFF +#define MODE_PRIORITY_OFF (1 << 16) +#define MODE_PRIORITY_ALWAYS_ON (1 << 20) +#define MODE_PRIORITY_FORCE_MASK (1 << 24) +#define D1MODE_PRIORITY_B_CNT 0x654C +#define LB_MAX_REQ_OUTSTANDING 0x6D58 +#define LB_D1_MAX_REQ_OUTSTANDING_MASK 0x0000000F +#define LB_D1_MAX_REQ_OUTSTANDING_SHIFT 0 +#define LB_D2_MAX_REQ_OUTSTANDING_MASK 0x000F0000 +#define LB_D2_MAX_REQ_OUTSTANDING_SHIFT 16 +#define DCP_CONTROL 0x6C9C +#define D2MODE_PRIORITY_A_CNT 0x6D48 +#define D2MODE_PRIORITY_B_CNT 0x6D4C + +/* MC indirect registers */ +#define MC_STATUS_IDLE (1 << 0) +#define MC_MISC_CNTL 0x18 +#define DISABLE_GTW (1 << 1) +#define GART_INDEX_REG_EN (1 << 12) +#define BLOCK_GFX_D3_EN (1 << 14) +#define GART_FEATURE_ID 0x2B +#define HANG_EN (1 << 11) +#define TLB_ENABLE (1 << 18) +#define P2P_ENABLE (1 << 19) +#define GTW_LAC_EN (1 << 25) +#define LEVEL2_GART (0 << 30) +#define LEVEL1_GART (1 << 30) +#define PDC_EN (1 << 31) +#define GART_BASE 0x2C +#define GART_CACHE_CNTRL 0x2E +# define GART_CACHE_INVALIDATE (1 << 0) +#define MC_STATUS 0x90 +#define MCCFG_FB_LOCATION 0x100 +#define MC_FB_START_MASK 0x0000FFFF +#define MC_FB_START_SHIFT 0 +#define MC_FB_TOP_MASK 0xFFFF0000 +#define MC_FB_TOP_SHIFT 16 +#define MCCFG_AGP_LOCATION 0x101 +#define MC_AGP_START_MASK 0x0000FFFF +#define MC_AGP_START_SHIFT 0 +#define MC_AGP_TOP_MASK 0xFFFF0000 +#define MC_AGP_TOP_SHIFT 16 +#define MCCFG_AGP_BASE 0x102 +#define MCCFG_AGP_BASE_2 0x103 +#define MC_INIT_MISC_LAT_TIMER 0x104 +#define MC_DISP0R_INIT_LAT_SHIFT 8 +#define MC_DISP0R_INIT_LAT_MASK 0x00000F00 +#define MC_DISP1R_INIT_LAT_SHIFT 12 +#define MC_DISP1R_INIT_LAT_MASK 0x0000F000 + +#endif diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 677929ed8ed3..4fd411893b91 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -27,8 +27,9 @@ */ #include #include "drmP.h" -#include "radeon_reg.h" +#include "rv515r.h" #include "radeon.h" +#include "radeon_share.h" /* rv515 depends on : */ void r100_hdp_reset(struct radeon_device *rdev); @@ -100,25 +101,25 @@ int rv515_mc_init(struct radeon_device *rdev) } /* Write VRAM size in case we are limiting it */ WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16); + tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32(0x134, tmp); tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; - tmp = REG_SET(RV515_MC_FB_TOP, tmp >> 16); - tmp |= REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16); - WREG32_MC(RV515_MC_FB_LOCATION, tmp); - WREG32(RS690_HDP_FB_LOCATION, rdev->mc.vram_location >> 16); + tmp = REG_SET(MC_FB_TOP, tmp >> 16); + tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); + WREG32_MC(MC_FB_LOCATION, tmp); + WREG32(HDP_FB_LOCATION, rdev->mc.vram_location >> 16); WREG32(0x310, rdev->mc.vram_location); if (rdev->flags & RADEON_IS_AGP) { tmp = rdev->mc.gtt_location + rdev->mc.gtt_size - 1; - tmp = REG_SET(RV515_MC_AGP_TOP, tmp >> 16); - tmp |= REG_SET(RV515_MC_AGP_START, rdev->mc.gtt_location >> 16); - WREG32_MC(RV515_MC_AGP_LOCATION, tmp); - WREG32_MC(RV515_MC_AGP_BASE, rdev->mc.agp_base); - WREG32_MC(RV515_MC_AGP_BASE_2, 0); + tmp = REG_SET(MC_AGP_TOP, tmp >> 16); + tmp |= REG_SET(MC_AGP_START, rdev->mc.gtt_location >> 16); + WREG32_MC(MC_AGP_LOCATION, tmp); + WREG32_MC(MC_AGP_BASE, rdev->mc.agp_base); + WREG32_MC(MC_AGP_BASE_2, 0); } else { - WREG32_MC(RV515_MC_AGP_LOCATION, 0x0FFFFFFF); - WREG32_MC(RV515_MC_AGP_BASE, 0); - WREG32_MC(RV515_MC_AGP_BASE_2, 0); + WREG32_MC(MC_AGP_LOCATION, 0x0FFFFFFF); + WREG32_MC(MC_AGP_BASE, 0); + WREG32_MC(MC_AGP_BASE_2, 0); } return 0; } @@ -136,95 +137,67 @@ void rv515_mc_fini(struct radeon_device *rdev) */ void rv515_ring_start(struct radeon_device *rdev) { - unsigned gb_tile_config; int r; - /* Sub pixel 1/12 so we can have 4K rendering according to doc */ - gb_tile_config = R300_ENABLE_TILING | R300_TILE_SIZE_16; - switch (rdev->num_gb_pipes) { - case 2: - gb_tile_config |= R300_PIPE_COUNT_R300; - break; - case 3: - gb_tile_config |= R300_PIPE_COUNT_R420_3P; - break; - case 4: - gb_tile_config |= R300_PIPE_COUNT_R420; - break; - case 1: - default: - gb_tile_config |= R300_PIPE_COUNT_RV350; - break; - } - r = radeon_ring_lock(rdev, 64); if (r) { return; } - radeon_ring_write(rdev, PACKET0(RADEON_ISYNC_CNTL, 0)); - radeon_ring_write(rdev, - RADEON_ISYNC_ANY2D_IDLE3D | - RADEON_ISYNC_ANY3D_IDLE2D | - RADEON_ISYNC_WAIT_IDLEGUI | - RADEON_ISYNC_CPSCRATCH_IDLEGUI); - radeon_ring_write(rdev, PACKET0(R300_GB_TILE_CONFIG, 0)); - radeon_ring_write(rdev, gb_tile_config); - radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0)); + radeon_ring_write(rdev, PACKET0(ISYNC_CNTL, 0)); radeon_ring_write(rdev, - RADEON_WAIT_2D_IDLECLEAN | - RADEON_WAIT_3D_IDLECLEAN); + ISYNC_ANY2D_IDLE3D | + ISYNC_ANY3D_IDLE2D | + ISYNC_WAIT_IDLEGUI | + ISYNC_CPSCRATCH_IDLEGUI); + radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0)); + radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN); radeon_ring_write(rdev, PACKET0(0x170C, 0)); radeon_ring_write(rdev, 1 << 31); - radeon_ring_write(rdev, PACKET0(R300_GB_SELECT, 0)); + radeon_ring_write(rdev, PACKET0(GB_SELECT, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_GB_ENABLE, 0)); + radeon_ring_write(rdev, PACKET0(GB_ENABLE, 0)); radeon_ring_write(rdev, 0); radeon_ring_write(rdev, PACKET0(0x42C8, 0)); radeon_ring_write(rdev, (1 << rdev->num_gb_pipes) - 1); - radeon_ring_write(rdev, PACKET0(R500_VAP_INDEX_OFFSET, 0)); + radeon_ring_write(rdev, PACKET0(VAP_INDEX_OFFSET, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE); - radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE); - radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0)); - radeon_ring_write(rdev, - RADEON_WAIT_2D_IDLECLEAN | - RADEON_WAIT_3D_IDLECLEAN); - radeon_ring_write(rdev, PACKET0(R300_GB_AA_CONFIG, 0)); + radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE); + radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE); + radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0)); + radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN); + radeon_ring_write(rdev, PACKET0(GB_AA_CONFIG, 0)); radeon_ring_write(rdev, 0); - radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE); - radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0)); - radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE); - radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS0, 0)); - radeon_ring_write(rdev, - ((6 << R300_MS_X0_SHIFT) | - (6 << R300_MS_Y0_SHIFT) | - (6 << R300_MS_X1_SHIFT) | - (6 << R300_MS_Y1_SHIFT) | - (6 << R300_MS_X2_SHIFT) | - (6 << R300_MS_Y2_SHIFT) | - (6 << R300_MSBD0_Y_SHIFT) | - (6 << R300_MSBD0_X_SHIFT))); - radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS1, 0)); - radeon_ring_write(rdev, - ((6 << R300_MS_X3_SHIFT) | - (6 << R300_MS_Y3_SHIFT) | - (6 << R300_MS_X4_SHIFT) | - (6 << R300_MS_Y4_SHIFT) | - (6 << R300_MS_X5_SHIFT) | - (6 << R300_MS_Y5_SHIFT) | - (6 << R300_MSBD1_SHIFT))); - radeon_ring_write(rdev, PACKET0(R300_GA_ENHANCE, 0)); - radeon_ring_write(rdev, R300_GA_DEADLOCK_CNTL | R300_GA_FASTSYNC_CNTL); - radeon_ring_write(rdev, PACKET0(R300_GA_POLY_MODE, 0)); + radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE); + radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0)); + radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE); + radeon_ring_write(rdev, PACKET0(GB_MSPOS0, 0)); radeon_ring_write(rdev, - R300_FRONT_PTYPE_TRIANGE | R300_BACK_PTYPE_TRIANGE); - radeon_ring_write(rdev, PACKET0(R300_GA_ROUND_MODE, 0)); + ((6 << MS_X0_SHIFT) | + (6 << MS_Y0_SHIFT) | + (6 << MS_X1_SHIFT) | + (6 << MS_Y1_SHIFT) | + (6 << MS_X2_SHIFT) | + (6 << MS_Y2_SHIFT) | + (6 << MSBD0_Y_SHIFT) | + (6 << MSBD0_X_SHIFT))); + radeon_ring_write(rdev, PACKET0(GB_MSPOS1, 0)); radeon_ring_write(rdev, - R300_GEOMETRY_ROUND_NEAREST | - R300_COLOR_ROUND_NEAREST); + ((6 << MS_X3_SHIFT) | + (6 << MS_Y3_SHIFT) | + (6 << MS_X4_SHIFT) | + (6 << MS_Y4_SHIFT) | + (6 << MS_X5_SHIFT) | + (6 << MS_Y5_SHIFT) | + (6 << MSBD1_SHIFT))); + radeon_ring_write(rdev, PACKET0(GA_ENHANCE, 0)); + radeon_ring_write(rdev, GA_DEADLOCK_CNTL | GA_FASTSYNC_CNTL); + radeon_ring_write(rdev, PACKET0(GA_POLY_MODE, 0)); + radeon_ring_write(rdev, FRONT_PTYPE_TRIANGE | BACK_PTYPE_TRIANGE); + radeon_ring_write(rdev, PACKET0(GA_ROUND_MODE, 0)); + radeon_ring_write(rdev, GEOMETRY_ROUND_NEAREST | COLOR_ROUND_NEAREST); radeon_ring_write(rdev, PACKET0(0x20C8, 0)); radeon_ring_write(rdev, 0); radeon_ring_unlock_commit(rdev); @@ -242,8 +215,8 @@ int rv515_mc_wait_for_idle(struct radeon_device *rdev) for (i = 0; i < rdev->usec_timeout; i++) { /* read MC_STATUS */ - tmp = RREG32_MC(RV515_MC_STATUS); - if (tmp & RV515_MC_STATUS_IDLE) { + tmp = RREG32_MC(MC_STATUS); + if (tmp & MC_STATUS_IDLE) { return 0; } DRM_UDELAY(1); @@ -291,33 +264,33 @@ int rv515_ga_reset(struct radeon_device *rdev) reinit_cp = rdev->cp.ready; rdev->cp.ready = false; for (i = 0; i < rdev->usec_timeout; i++) { - WREG32(RADEON_CP_CSQ_MODE, 0); - WREG32(RADEON_CP_CSQ_CNTL, 0); - WREG32(RADEON_RBBM_SOFT_RESET, 0x32005); - (void)RREG32(RADEON_RBBM_SOFT_RESET); + WREG32(CP_CSQ_MODE, 0); + WREG32(CP_CSQ_CNTL, 0); + WREG32(RBBM_SOFT_RESET, 0x32005); + (void)RREG32(RBBM_SOFT_RESET); udelay(200); - WREG32(RADEON_RBBM_SOFT_RESET, 0); + WREG32(RBBM_SOFT_RESET, 0); /* Wait to prevent race in RBBM_STATUS */ mdelay(1); - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (tmp & ((1 << 20) | (1 << 26))) { DRM_ERROR("VAP & CP still busy (RBBM_STATUS=0x%08X)\n", tmp); /* GA still busy soft reset it */ WREG32(0x429C, 0x200); - WREG32(R300_VAP_PVS_STATE_FLUSH_REG, 0); + WREG32(VAP_PVS_STATE_FLUSH_REG, 0); WREG32(0x43E0, 0); WREG32(0x43E4, 0); WREG32(0x24AC, 0); } /* Wait to prevent race in RBBM_STATUS */ mdelay(1); - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (!(tmp & ((1 << 20) | (1 << 26)))) { break; } } for (i = 0; i < rdev->usec_timeout; i++) { - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); if (!(tmp & ((1 << 20) | (1 << 26)))) { DRM_INFO("GA reset succeed (RBBM_STATUS=0x%08X)\n", tmp); @@ -331,7 +304,7 @@ int rv515_ga_reset(struct radeon_device *rdev) } DRM_UDELAY(1); } - tmp = RREG32(RADEON_RBBM_STATUS); + tmp = RREG32(RBBM_STATUS); DRM_ERROR("Failed to reset GA ! (RBBM_STATUS=0x%08X)\n", tmp); return -1; } @@ -341,7 +314,7 @@ int rv515_gpu_reset(struct radeon_device *rdev) uint32_t status; /* reset order likely matter */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); /* reset HDP */ r100_hdp_reset(rdev); /* reset rb2d */ @@ -353,12 +326,12 @@ int rv515_gpu_reset(struct radeon_device *rdev) rv515_ga_reset(rdev); } /* reset CP */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); if (status & (1 << 16)) { r100_cp_reset(rdev); } /* Check if GPU is idle */ - status = RREG32(RADEON_RBBM_STATUS); + status = RREG32(RBBM_STATUS); if (status & (1 << 31)) { DRM_ERROR("Failed to reset GPU (RBBM_STATUS=0x%08X)\n", status); return -1; @@ -377,8 +350,7 @@ static void rv515_vram_get_type(struct radeon_device *rdev) rdev->mc.vram_width = 128; rdev->mc.vram_is_ddr = true; - tmp = RREG32_MC(RV515_MC_CNTL); - tmp &= RV515_MEM_NUM_CHANNELS_MASK; + tmp = RREG32_MC(RV515_MC_CNTL) & MEM_NUM_CHANNELS_MASK; switch (tmp) { case 0: rdev->mc.vram_width = 64; @@ -394,9 +366,19 @@ static void rv515_vram_get_type(struct radeon_device *rdev) void rv515_vram_info(struct radeon_device *rdev) { + fixed20_12 a; + rv515_vram_get_type(rdev); - - r100_vram_init_sizes(rdev); + rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE); + + rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); + rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); + /* FIXME: we should enforce default clock in case GPU is not in + * default setup + */ + a.full = rfixed_const(100); + rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk); + rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a); } @@ -407,35 +389,35 @@ uint32_t rv515_mc_rreg(struct radeon_device *rdev, uint32_t reg) { uint32_t r; - WREG32(R520_MC_IND_INDEX, 0x7f0000 | (reg & 0xffff)); - r = RREG32(R520_MC_IND_DATA); - WREG32(R520_MC_IND_INDEX, 0); + WREG32(MC_IND_INDEX, 0x7f0000 | (reg & 0xffff)); + r = RREG32(MC_IND_DATA); + WREG32(MC_IND_INDEX, 0); return r; } void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) { - WREG32(R520_MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff)); - WREG32(R520_MC_IND_DATA, (v)); - WREG32(R520_MC_IND_INDEX, 0); + WREG32(MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff)); + WREG32(MC_IND_DATA, (v)); + WREG32(MC_IND_INDEX, 0); } uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg) { uint32_t r; - WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(RADEON_PCIE_INDEX); - r = RREG32(RADEON_PCIE_DATA); + WREG32(PCIE_INDEX, ((reg) & 0x7ff)); + (void)RREG32(PCIE_INDEX); + r = RREG32(PCIE_DATA); return r; } void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) { - WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(RADEON_PCIE_INDEX); - WREG32(RADEON_PCIE_DATA, (v)); - (void)RREG32(RADEON_PCIE_DATA); + WREG32(PCIE_INDEX, ((reg) & 0x7ff)); + (void)RREG32(PCIE_INDEX); + WREG32(PCIE_DATA, (v)); + (void)RREG32(PCIE_DATA); } @@ -450,13 +432,13 @@ static int rv515_debugfs_pipes_info(struct seq_file *m, void *data) struct radeon_device *rdev = dev->dev_private; uint32_t tmp; - tmp = RREG32(R400_GB_PIPE_SELECT); + tmp = RREG32(GB_PIPE_SELECT); seq_printf(m, "GB_PIPE_SELECT 0x%08x\n", tmp); - tmp = RREG32(R500_SU_REG_DEST); + tmp = RREG32(SU_REG_DEST); seq_printf(m, "SU_REG_DEST 0x%08x\n", tmp); - tmp = RREG32(R300_GB_TILE_CONFIG); + tmp = RREG32(GB_TILE_CONFIG); seq_printf(m, "GB_TILE_CONFIG 0x%08x\n", tmp); - tmp = RREG32(R300_DST_PIPE_CONFIG); + tmp = RREG32(DST_PIPE_CONFIG); seq_printf(m, "DST_PIPE_CONFIG 0x%08x\n", tmp); return 0; } @@ -571,3 +553,551 @@ int rv515_init(struct radeon_device *rdev) rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(r500_reg_safe_bm); return 0; } + +void atom_rv515_force_tv_scaler(struct radeon_device *rdev) +{ + + WREG32(0x659C, 0x0); + WREG32(0x6594, 0x705); + WREG32(0x65A4, 0x10001); + WREG32(0x65D8, 0x0); + WREG32(0x65B0, 0x0); + WREG32(0x65C0, 0x0); + WREG32(0x65D4, 0x0); + WREG32(0x6578, 0x0); + WREG32(0x657C, 0x841880A8); + WREG32(0x6578, 0x1); + WREG32(0x657C, 0x84208680); + WREG32(0x6578, 0x2); + WREG32(0x657C, 0xBFF880B0); + WREG32(0x6578, 0x100); + WREG32(0x657C, 0x83D88088); + WREG32(0x6578, 0x101); + WREG32(0x657C, 0x84608680); + WREG32(0x6578, 0x102); + WREG32(0x657C, 0xBFF080D0); + WREG32(0x6578, 0x200); + WREG32(0x657C, 0x83988068); + WREG32(0x6578, 0x201); + WREG32(0x657C, 0x84A08680); + WREG32(0x6578, 0x202); + WREG32(0x657C, 0xBFF080F8); + WREG32(0x6578, 0x300); + WREG32(0x657C, 0x83588058); + WREG32(0x6578, 0x301); + WREG32(0x657C, 0x84E08660); + WREG32(0x6578, 0x302); + WREG32(0x657C, 0xBFF88120); + WREG32(0x6578, 0x400); + WREG32(0x657C, 0x83188040); + WREG32(0x6578, 0x401); + WREG32(0x657C, 0x85008660); + WREG32(0x6578, 0x402); + WREG32(0x657C, 0xBFF88150); + WREG32(0x6578, 0x500); + WREG32(0x657C, 0x82D88030); + WREG32(0x6578, 0x501); + WREG32(0x657C, 0x85408640); + WREG32(0x6578, 0x502); + WREG32(0x657C, 0xBFF88180); + WREG32(0x6578, 0x600); + WREG32(0x657C, 0x82A08018); + WREG32(0x6578, 0x601); + WREG32(0x657C, 0x85808620); + WREG32(0x6578, 0x602); + WREG32(0x657C, 0xBFF081B8); + WREG32(0x6578, 0x700); + WREG32(0x657C, 0x82608010); + WREG32(0x6578, 0x701); + WREG32(0x657C, 0x85A08600); + WREG32(0x6578, 0x702); + WREG32(0x657C, 0x800081F0); + WREG32(0x6578, 0x800); + WREG32(0x657C, 0x8228BFF8); + WREG32(0x6578, 0x801); + WREG32(0x657C, 0x85E085E0); + WREG32(0x6578, 0x802); + WREG32(0x657C, 0xBFF88228); + WREG32(0x6578, 0x10000); + WREG32(0x657C, 0x82A8BF00); + WREG32(0x6578, 0x10001); + WREG32(0x657C, 0x82A08CC0); + WREG32(0x6578, 0x10002); + WREG32(0x657C, 0x8008BEF8); + WREG32(0x6578, 0x10100); + WREG32(0x657C, 0x81F0BF28); + WREG32(0x6578, 0x10101); + WREG32(0x657C, 0x83608CA0); + WREG32(0x6578, 0x10102); + WREG32(0x657C, 0x8018BED0); + WREG32(0x6578, 0x10200); + WREG32(0x657C, 0x8148BF38); + WREG32(0x6578, 0x10201); + WREG32(0x657C, 0x84408C80); + WREG32(0x6578, 0x10202); + WREG32(0x657C, 0x8008BEB8); + WREG32(0x6578, 0x10300); + WREG32(0x657C, 0x80B0BF78); + WREG32(0x6578, 0x10301); + WREG32(0x657C, 0x85008C20); + WREG32(0x6578, 0x10302); + WREG32(0x657C, 0x8020BEA0); + WREG32(0x6578, 0x10400); + WREG32(0x657C, 0x8028BF90); + WREG32(0x6578, 0x10401); + WREG32(0x657C, 0x85E08BC0); + WREG32(0x6578, 0x10402); + WREG32(0x657C, 0x8018BE90); + WREG32(0x6578, 0x10500); + WREG32(0x657C, 0xBFB8BFB0); + WREG32(0x6578, 0x10501); + WREG32(0x657C, 0x86C08B40); + WREG32(0x6578, 0x10502); + WREG32(0x657C, 0x8010BE90); + WREG32(0x6578, 0x10600); + WREG32(0x657C, 0xBF58BFC8); + WREG32(0x6578, 0x10601); + WREG32(0x657C, 0x87A08AA0); + WREG32(0x6578, 0x10602); + WREG32(0x657C, 0x8010BE98); + WREG32(0x6578, 0x10700); + WREG32(0x657C, 0xBF10BFF0); + WREG32(0x6578, 0x10701); + WREG32(0x657C, 0x886089E0); + WREG32(0x6578, 0x10702); + WREG32(0x657C, 0x8018BEB0); + WREG32(0x6578, 0x10800); + WREG32(0x657C, 0xBED8BFE8); + WREG32(0x6578, 0x10801); + WREG32(0x657C, 0x89408940); + WREG32(0x6578, 0x10802); + WREG32(0x657C, 0xBFE8BED8); + WREG32(0x6578, 0x20000); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20001); + WREG32(0x657C, 0x90008000); + WREG32(0x6578, 0x20002); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20003); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20100); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20101); + WREG32(0x657C, 0x8FE0BF70); + WREG32(0x6578, 0x20102); + WREG32(0x657C, 0xBFE880C0); + WREG32(0x6578, 0x20103); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20200); + WREG32(0x657C, 0x8018BFF8); + WREG32(0x6578, 0x20201); + WREG32(0x657C, 0x8F80BF08); + WREG32(0x6578, 0x20202); + WREG32(0x657C, 0xBFD081A0); + WREG32(0x6578, 0x20203); + WREG32(0x657C, 0xBFF88000); + WREG32(0x6578, 0x20300); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20301); + WREG32(0x657C, 0x8EE0BEC0); + WREG32(0x6578, 0x20302); + WREG32(0x657C, 0xBFB082A0); + WREG32(0x6578, 0x20303); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20400); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20401); + WREG32(0x657C, 0x8E00BEA0); + WREG32(0x6578, 0x20402); + WREG32(0x657C, 0xBF8883C0); + WREG32(0x6578, 0x20403); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x20500); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20501); + WREG32(0x657C, 0x8D00BE90); + WREG32(0x6578, 0x20502); + WREG32(0x657C, 0xBF588500); + WREG32(0x6578, 0x20503); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20600); + WREG32(0x657C, 0x80188000); + WREG32(0x6578, 0x20601); + WREG32(0x657C, 0x8BC0BE98); + WREG32(0x6578, 0x20602); + WREG32(0x657C, 0xBF308660); + WREG32(0x6578, 0x20603); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20700); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20701); + WREG32(0x657C, 0x8A80BEB0); + WREG32(0x6578, 0x20702); + WREG32(0x657C, 0xBF0087C0); + WREG32(0x6578, 0x20703); + WREG32(0x657C, 0x80008008); + WREG32(0x6578, 0x20800); + WREG32(0x657C, 0x80108000); + WREG32(0x6578, 0x20801); + WREG32(0x657C, 0x8920BED0); + WREG32(0x6578, 0x20802); + WREG32(0x657C, 0xBED08920); + WREG32(0x6578, 0x20803); + WREG32(0x657C, 0x80008010); + WREG32(0x6578, 0x30000); + WREG32(0x657C, 0x90008000); + WREG32(0x6578, 0x30001); + WREG32(0x657C, 0x80008000); + WREG32(0x6578, 0x30100); + WREG32(0x657C, 0x8FE0BF90); + WREG32(0x6578, 0x30101); + WREG32(0x657C, 0xBFF880A0); + WREG32(0x6578, 0x30200); + WREG32(0x657C, 0x8F60BF40); + WREG32(0x6578, 0x30201); + WREG32(0x657C, 0xBFE88180); + WREG32(0x6578, 0x30300); + WREG32(0x657C, 0x8EC0BF00); + WREG32(0x6578, 0x30301); + WREG32(0x657C, 0xBFC88280); + WREG32(0x6578, 0x30400); + WREG32(0x657C, 0x8DE0BEE0); + WREG32(0x6578, 0x30401); + WREG32(0x657C, 0xBFA083A0); + WREG32(0x6578, 0x30500); + WREG32(0x657C, 0x8CE0BED0); + WREG32(0x6578, 0x30501); + WREG32(0x657C, 0xBF7884E0); + WREG32(0x6578, 0x30600); + WREG32(0x657C, 0x8BA0BED8); + WREG32(0x6578, 0x30601); + WREG32(0x657C, 0xBF508640); + WREG32(0x6578, 0x30700); + WREG32(0x657C, 0x8A60BEE8); + WREG32(0x6578, 0x30701); + WREG32(0x657C, 0xBF2087A0); + WREG32(0x6578, 0x30800); + WREG32(0x657C, 0x8900BF00); + WREG32(0x6578, 0x30801); + WREG32(0x657C, 0xBF008900); +} + +struct rv515_watermark { + u32 lb_request_fifo_depth; + fixed20_12 num_line_pair; + fixed20_12 estimated_width; + fixed20_12 worst_case_latency; + fixed20_12 consumption_rate; + fixed20_12 active_time; + fixed20_12 dbpp; + fixed20_12 priority_mark_max; + fixed20_12 priority_mark; + fixed20_12 sclk; +}; + +void rv515_crtc_bandwidth_compute(struct radeon_device *rdev, + struct radeon_crtc *crtc, + struct rv515_watermark *wm) +{ + struct drm_display_mode *mode = &crtc->base.mode; + fixed20_12 a, b, c; + fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width; + fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency; + + if (!crtc->base.enabled) { + /* FIXME: wouldn't it better to set priority mark to maximum */ + wm->lb_request_fifo_depth = 4; + return; + } + + if (crtc->vsc.full > rfixed_const(2)) + wm->num_line_pair.full = rfixed_const(2); + else + wm->num_line_pair.full = rfixed_const(1); + + b.full = rfixed_const(mode->crtc_hdisplay); + c.full = rfixed_const(256); + a.full = rfixed_mul(wm->num_line_pair, b); + request_fifo_depth.full = rfixed_div(a, c); + if (a.full < rfixed_const(4)) { + wm->lb_request_fifo_depth = 4; + } else { + wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth); + } + + /* Determine consumption rate + * pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000) + * vtaps = number of vertical taps, + * vsc = vertical scaling ratio, defined as source/destination + * hsc = horizontal scaling ration, defined as source/destination + */ + a.full = rfixed_const(mode->clock); + b.full = rfixed_const(1000); + a.full = rfixed_div(a, b); + pclk.full = rfixed_div(b, a); + if (crtc->rmx_type != RMX_OFF) { + b.full = rfixed_const(2); + if (crtc->vsc.full > b.full) + b.full = crtc->vsc.full; + b.full = rfixed_mul(b, crtc->hsc); + c.full = rfixed_const(2); + b.full = rfixed_div(b, c); + consumption_time.full = rfixed_div(pclk, b); + } else { + consumption_time.full = pclk.full; + } + a.full = rfixed_const(1); + wm->consumption_rate.full = rfixed_div(a, consumption_time); + + + /* Determine line time + * LineTime = total time for one line of displayhtotal + * LineTime = total number of horizontal pixels + * pclk = pixel clock period(ns) + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + line_time.full = rfixed_mul(a, pclk); + + /* Determine active time + * ActiveTime = time of active region of display within one line, + * hactive = total number of horizontal active pixels + * htotal = total number of horizontal pixels + */ + a.full = rfixed_const(crtc->base.mode.crtc_htotal); + b.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->active_time.full = rfixed_mul(line_time, b); + wm->active_time.full = rfixed_div(wm->active_time, a); + + /* Determine chunk time + * ChunkTime = the time it takes the DCP to send one chunk of data + * to the LB which consists of pipeline delay and inter chunk gap + * sclk = system clock(Mhz) + */ + a.full = rfixed_const(600 * 1000); + chunk_time.full = rfixed_div(a, rdev->pm.sclk); + read_delay_latency.full = rfixed_const(1000); + + /* Determine the worst case latency + * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines) + * WorstCaseLatency = worst case time from urgent to when the MC starts + * to return data + * READ_DELAY_IDLE_MAX = constant of 1us + * ChunkTime = time it takes the DCP to send one chunk of data to the LB + * which consists of pipeline delay and inter chunk gap + */ + if (rfixed_trunc(wm->num_line_pair) > 1) { + a.full = rfixed_const(3); + wm->worst_case_latency.full = rfixed_mul(a, chunk_time); + wm->worst_case_latency.full += read_delay_latency.full; + } else { + wm->worst_case_latency.full = chunk_time.full + read_delay_latency.full; + } + + /* Determine the tolerable latency + * TolerableLatency = Any given request has only 1 line time + * for the data to be returned + * LBRequestFifoDepth = Number of chunk requests the LB can + * put into the request FIFO for a display + * LineTime = total time for one line of display + * ChunkTime = the time it takes the DCP to send one chunk + * of data to the LB which consists of + * pipeline delay and inter chunk gap + */ + if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) { + tolerable_latency.full = line_time.full; + } else { + tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2); + tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full; + tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time); + tolerable_latency.full = line_time.full - tolerable_latency.full; + } + /* We assume worst case 32bits (4 bytes) */ + wm->dbpp.full = rfixed_const(2 * 16); + + /* Determine the maximum priority mark + * width = viewport width in pixels + */ + a.full = rfixed_const(16); + wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay); + wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a); + + /* Determine estimated width */ + estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full; + estimated_width.full = rfixed_div(estimated_width, consumption_time); + if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) { + wm->priority_mark.full = rfixed_const(10); + } else { + a.full = rfixed_const(16); + wm->priority_mark.full = rfixed_div(estimated_width, a); + wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full; + } +} + +void rv515_bandwidth_avivo_update(struct radeon_device *rdev) +{ + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + struct rv515_watermark wm0; + struct rv515_watermark wm1; + u32 tmp; + fixed20_12 priority_mark02, priority_mark12, fill_rate; + fixed20_12 a, b; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + rs690_line_buffer_adjust(rdev, mode0, mode1); + + rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0); + rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1); + + tmp = wm0.lb_request_fifo_depth; + tmp |= wm1.lb_request_fifo_depth << 16; + WREG32(LB_MAX_REQ_OUTSTANDING, tmp); + + if (mode0 && mode1) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + if (rfixed_trunc(wm1.dbpp) > 64) + b.full = rfixed_div(wm1.dbpp, wm1.num_line_pair); + else + b.full = wm1.num_line_pair.full; + a.full += b.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + priority_mark02.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark02.full = rfixed_div(a, b); + } + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + priority_mark12.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } else if (mode0) { + if (rfixed_trunc(wm0.dbpp) > 64) + a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair); + else + a.full = wm0.num_line_pair.full; + fill_rate.full = rfixed_div(wm0.sclk, a); + if (wm0.consumption_rate.full > fill_rate.full) { + b.full = wm0.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm0.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + priority_mark02.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm0.worst_case_latency, + wm0.consumption_rate); + b.full = rfixed_const(16); + priority_mark02.full = rfixed_div(a, b); + } + if (wm0.priority_mark.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark.full; + if (rfixed_trunc(priority_mark02) < 0) + priority_mark02.full = 0; + if (wm0.priority_mark_max.full > priority_mark02.full) + priority_mark02.full = wm0.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02)); + WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02)); + WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + } else { + if (rfixed_trunc(wm1.dbpp) > 64) + a.full = rfixed_div(wm1.dbpp, wm1.num_line_pair); + else + a.full = wm1.num_line_pair.full; + fill_rate.full = rfixed_div(wm1.sclk, a); + if (wm1.consumption_rate.full > fill_rate.full) { + b.full = wm1.consumption_rate.full - fill_rate.full; + b.full = rfixed_mul(b, wm1.active_time); + a.full = rfixed_const(16); + b.full = rfixed_div(b, a); + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + priority_mark12.full = a.full + b.full; + } else { + a.full = rfixed_mul(wm1.worst_case_latency, + wm1.consumption_rate); + b.full = rfixed_const(16 * 1000); + priority_mark12.full = rfixed_div(a, b); + } + if (wm1.priority_mark.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark.full; + if (rfixed_trunc(priority_mark12) < 0) + priority_mark12.full = 0; + if (wm1.priority_mark_max.full > priority_mark12.full) + priority_mark12.full = wm1.priority_mark_max.full; + WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF); + WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF); + WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12)); + WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12)); + } +} + +void rv515_bandwidth_update(struct radeon_device *rdev) +{ + uint32_t tmp; + struct drm_display_mode *mode0 = NULL; + struct drm_display_mode *mode1 = NULL; + + if (rdev->mode_info.crtcs[0]->base.enabled) + mode0 = &rdev->mode_info.crtcs[0]->base.mode; + if (rdev->mode_info.crtcs[1]->base.enabled) + mode1 = &rdev->mode_info.crtcs[1]->base.mode; + /* + * Set display0/1 priority up in the memory controller for + * modes if the user specifies HIGH for displaypriority + * option. + */ + if (rdev->disp_priority == 2) { + tmp = RREG32_MC(MC_MISC_LAT_TIMER); + tmp &= ~MC_DISP1R_INIT_LAT_MASK; + tmp &= ~MC_DISP0R_INIT_LAT_MASK; + if (mode1) + tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT); + if (mode0) + tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT); + WREG32_MC(MC_MISC_LAT_TIMER, tmp); + } + rv515_bandwidth_avivo_update(rdev); +} diff --git a/drivers/gpu/drm/radeon/rv515r.h b/drivers/gpu/drm/radeon/rv515r.h new file mode 100644 index 000000000000..f3cf84039906 --- /dev/null +++ b/drivers/gpu/drm/radeon/rv515r.h @@ -0,0 +1,170 @@ +/* + * Copyright 2008 Advanced Micro Devices, Inc. + * Copyright 2008 Red Hat Inc. + * Copyright 2009 Jerome Glisse. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Dave Airlie + * Alex Deucher + * Jerome Glisse + */ +#ifndef RV515R_H +#define RV515R_H + +/* RV515 registers */ +#define PCIE_INDEX 0x0030 +#define PCIE_DATA 0x0034 +#define MC_IND_INDEX 0x0070 +#define MC_IND_WR_EN (1 << 24) +#define MC_IND_DATA 0x0074 +#define RBBM_SOFT_RESET 0x00F0 +#define CONFIG_MEMSIZE 0x00F8 +#define HDP_FB_LOCATION 0x0134 +#define CP_CSQ_CNTL 0x0740 +#define CP_CSQ_MODE 0x0744 +#define CP_CSQ_ADDR 0x07F0 +#define CP_CSQ_DATA 0x07F4 +#define CP_CSQ_STAT 0x07F8 +#define CP_CSQ2_STAT 0x07FC +#define RBBM_STATUS 0x0E40 +#define DST_PIPE_CONFIG 0x170C +#define WAIT_UNTIL 0x1720 +#define WAIT_2D_IDLE (1 << 14) +#define WAIT_3D_IDLE (1 << 15) +#define WAIT_2D_IDLECLEAN (1 << 16) +#define WAIT_3D_IDLECLEAN (1 << 17) +#define ISYNC_CNTL 0x1724 +#define ISYNC_ANY2D_IDLE3D (1 << 0) +#define ISYNC_ANY3D_IDLE2D (1 << 1) +#define ISYNC_TRIG2D_IDLE3D (1 << 2) +#define ISYNC_TRIG3D_IDLE2D (1 << 3) +#define ISYNC_WAIT_IDLEGUI (1 << 4) +#define ISYNC_CPSCRATCH_IDLEGUI (1 << 5) +#define VAP_INDEX_OFFSET 0x208C +#define VAP_PVS_STATE_FLUSH_REG 0x2284 +#define GB_ENABLE 0x4008 +#define GB_MSPOS0 0x4010 +#define MS_X0_SHIFT 0 +#define MS_Y0_SHIFT 4 +#define MS_X1_SHIFT 8 +#define MS_Y1_SHIFT 12 +#define MS_X2_SHIFT 16 +#define MS_Y2_SHIFT 20 +#define MSBD0_Y_SHIFT 24 +#define MSBD0_X_SHIFT 28 +#define GB_MSPOS1 0x4014 +#define MS_X3_SHIFT 0 +#define MS_Y3_SHIFT 4 +#define MS_X4_SHIFT 8 +#define MS_Y4_SHIFT 12 +#define MS_X5_SHIFT 16 +#define MS_Y5_SHIFT 20 +#define MSBD1_SHIFT 24 +#define GB_TILE_CONFIG 0x4018 +#define ENABLE_TILING (1 << 0) +#define PIPE_COUNT_MASK 0x0000000E +#define PIPE_COUNT_SHIFT 1 +#define TILE_SIZE_8 (0 << 4) +#define TILE_SIZE_16 (1 << 4) +#define TILE_SIZE_32 (2 << 4) +#define SUBPIXEL_1_12 (0 << 16) +#define SUBPIXEL_1_16 (1 << 16) +#define GB_SELECT 0x401C +#define GB_AA_CONFIG 0x4020 +#define GB_PIPE_SELECT 0x402C +#define GA_ENHANCE 0x4274 +#define GA_DEADLOCK_CNTL (1 << 0) +#define GA_FASTSYNC_CNTL (1 << 1) +#define GA_POLY_MODE 0x4288 +#define FRONT_PTYPE_POINT (0 << 4) +#define FRONT_PTYPE_LINE (1 << 4) +#define FRONT_PTYPE_TRIANGE (2 << 4) +#define BACK_PTYPE_POINT (0 << 7) +#define BACK_PTYPE_LINE (1 << 7) +#define BACK_PTYPE_TRIANGE (2 << 7) +#define GA_ROUND_MODE 0x428C +#define GEOMETRY_ROUND_TRUNC (0 << 0) +#define GEOMETRY_ROUND_NEAREST (1 << 0) +#define COLOR_ROUND_TRUNC (0 << 2) +#define COLOR_ROUND_NEAREST (1 << 2) +#define SU_REG_DEST 0x42C8 +#define RB3D_DSTCACHE_CTLSTAT 0x4E4C +#define RB3D_DC_FLUSH (2 << 0) +#define RB3D_DC_FREE (2 << 2) +#define RB3D_DC_FINISH (1 << 4) +#define ZB_ZCACHE_CTLSTAT 0x4F18 +#define ZC_FLUSH (1 << 0) +#define ZC_FREE (1 << 1) +#define DC_LB_MEMORY_SPLIT 0x6520 +#define DC_LB_MEMORY_SPLIT_MASK 0x00000003 +#define DC_LB_MEMORY_SPLIT_SHIFT 0 +#define DC_LB_MEMORY_SPLIT_D1HALF_D2HALF 0 +#define DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q 1 +#define DC_LB_MEMORY_SPLIT_D1_ONLY 2 +#define DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q 3 +#define DC_LB_MEMORY_SPLIT_SHIFT_MODE (1 << 2) +#define DC_LB_DISP1_END_ADR_SHIFT 4 +#define DC_LB_DISP1_END_ADR_MASK 0x00007FF0 +#define D1MODE_PRIORITY_A_CNT 0x6548 +#define MODE_PRIORITY_MARK_MASK 0x00007FFF +#define MODE_PRIORITY_OFF (1 << 16) +#define MODE_PRIORITY_ALWAYS_ON (1 << 20) +#define MODE_PRIORITY_FORCE_MASK (1 << 24) +#define D1MODE_PRIORITY_B_CNT 0x654C +#define LB_MAX_REQ_OUTSTANDING 0x6D58 +#define LB_D1_MAX_REQ_OUTSTANDING_MASK 0x0000000F +#define LB_D1_MAX_REQ_OUTSTANDING_SHIFT 0 +#define LB_D2_MAX_REQ_OUTSTANDING_MASK 0x000F0000 +#define LB_D2_MAX_REQ_OUTSTANDING_SHIFT 16 +#define D2MODE_PRIORITY_A_CNT 0x6D48 +#define D2MODE_PRIORITY_B_CNT 0x6D4C + +/* ix[MC] registers */ +#define MC_FB_LOCATION 0x01 +#define MC_FB_START_MASK 0x0000FFFF +#define MC_FB_START_SHIFT 0 +#define MC_FB_TOP_MASK 0xFFFF0000 +#define MC_FB_TOP_SHIFT 16 +#define MC_AGP_LOCATION 0x02 +#define MC_AGP_START_MASK 0x0000FFFF +#define MC_AGP_START_SHIFT 0 +#define MC_AGP_TOP_MASK 0xFFFF0000 +#define MC_AGP_TOP_SHIFT 16 +#define MC_AGP_BASE 0x03 +#define MC_AGP_BASE_2 0x04 +#define MC_CNTL 0x5 +#define MEM_NUM_CHANNELS_MASK 0x00000003 +#define MC_STATUS 0x08 +#define MC_STATUS_IDLE (1 << 4) +#define MC_MISC_LAT_TIMER 0x09 +#define MC_CPR_INIT_LAT_MASK 0x0000000F +#define MC_VF_INIT_LAT_MASK 0x000000F0 +#define MC_DISP0R_INIT_LAT_MASK 0x00000F00 +#define MC_DISP0R_INIT_LAT_SHIFT 8 +#define MC_DISP1R_INIT_LAT_MASK 0x0000F000 +#define MC_DISP1R_INIT_LAT_SHIFT 12 +#define MC_FIXED_INIT_LAT_MASK 0x000F0000 +#define MC_E2R_INIT_LAT_MASK 0x00F00000 +#define SAME_PAGE_PRIO_MASK 0x0F000000 +#define MC_GLOBW_INIT_LAT_MASK 0xF0000000 + + +#endif + -- cgit v1.2.3 From e46074effd5510e7a8fe34b93828d98a50835da2 Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Tue, 28 Jul 2009 12:30:55 +0200 Subject: drm/radeon: Don't unreserve twice on failure to validate. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This is done later in radeon_object_list_unvalidate(). Doing it twice triggers a BUG in TTM, rendering X on KMS unusable until reboot. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index d5b1fd562d88..3961a44c5dce 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -433,7 +433,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence) robj->tobj.proposed_placement, true, false); if (unlikely(r)) { - radeon_object_list_unreserve(head); DRM_ERROR("radeon: failed to validate.\n"); return r; } -- cgit v1.2.3 From 1ab2e1059916b917af19e4137a4222988bd7a169 Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Tue, 28 Jul 2009 12:30:56 +0200 Subject: drm/radeon: Fall back to evicting BOs with memcpy if necessary. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Otherwise if there's no GTT space we would fail the eviction, leading to cascaded failure. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_ttm.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index 37e1cbcce3a9..f3469b96208c 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -355,23 +355,26 @@ static int radeon_bo_move(struct ttm_buffer_object *bo, if (!rdev->cp.ready) { /* use memcpy */ DRM_ERROR("CP is not ready use memcpy.\n"); - return ttm_bo_move_memcpy(bo, evict, no_wait, new_mem); + goto memcpy; } if (old_mem->mem_type == TTM_PL_VRAM && new_mem->mem_type == TTM_PL_SYSTEM) { - return radeon_move_vram_ram(bo, evict, interruptible, + r = radeon_move_vram_ram(bo, evict, interruptible, no_wait, new_mem); } else if (old_mem->mem_type == TTM_PL_SYSTEM && new_mem->mem_type == TTM_PL_VRAM) { - return radeon_move_ram_vram(bo, evict, interruptible, + r = radeon_move_ram_vram(bo, evict, interruptible, no_wait, new_mem); } else { r = radeon_move_blit(bo, evict, no_wait, new_mem, old_mem); - if (unlikely(r)) { - return r; - } } + + if (r) { +memcpy: + r = ttm_bo_move_memcpy(bo, evict, no_wait, new_mem); + } + return r; } -- cgit v1.2.3 From 664f86590295217b2319edf88830e87b800f6c4a Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Tue, 28 Jul 2009 12:30:57 +0200 Subject: drm/radeon: Pay more attention to object placement requested by userspace. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Previously we were basically always setting the GTT and VRAM flags regardless of what userspace requested. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 25 +++++++++++-------------- 1 file changed, 11 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index 3961a44c5dce..81573c3a9b43 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -103,16 +103,16 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain) { uint32_t flags = 0; if (domain & RADEON_GEM_DOMAIN_VRAM) { - flags |= TTM_PL_FLAG_VRAM; + flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_GTT) { - flags |= TTM_PL_FLAG_TT; + flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_CPU) { - flags |= TTM_PL_FLAG_SYSTEM; + flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; } if (!flags) { - flags |= TTM_PL_FLAG_SYSTEM; + flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; } return flags; } @@ -408,7 +408,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence) struct radeon_object *robj; struct radeon_fence *old_fence = NULL; struct list_head *i; - uint32_t flags; int r; r = radeon_object_list_reserve(head); @@ -419,16 +418,14 @@ int radeon_object_list_validate(struct list_head *head, void *fence) list_for_each(i, head) { lobj = list_entry(i, struct radeon_object_list, list); robj = lobj->robj; - if (lobj->wdomain) { - flags = radeon_object_flags_from_domain(lobj->wdomain); - flags |= TTM_PL_FLAG_TT; - } else { - flags = radeon_object_flags_from_domain(lobj->rdomain); - flags |= TTM_PL_FLAG_TT; - flags |= TTM_PL_FLAG_VRAM; - } if (!robj->pin_count) { - robj->tobj.proposed_placement = flags | TTM_PL_MASK_CACHING; + if (lobj->wdomain) { + robj->tobj.proposed_placement = + radeon_object_flags_from_domain(lobj->wdomain); + } else { + robj->tobj.proposed_placement = + radeon_object_flags_from_domain(lobj->rdomain); + } r = ttm_buffer_object_validate(&robj->tobj, robj->tobj.proposed_placement, true, false); -- cgit v1.2.3 From 7a50f01a4ab89d5c05eb2cf62e206ac0bfc61d2c Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 21 Jul 2009 20:39:30 +1000 Subject: drm/radeon/kms: vram sizing on certain r100 chips needs workaround. If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the aperture used to calculate the MC_FB_LOCATION needs to be worked out from the CONFIG_APER_SIZE register, and not the actual vram size. TTM VRAM size was also being initialised wrong, use actual vram size to initialise it. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 34 ++++++++++++++++++++++------------ drivers/gpu/drm/radeon/r520.c | 4 ++-- drivers/gpu/drm/radeon/r600.c | 5 +++-- drivers/gpu/drm/radeon/radeon.h | 5 ++++- drivers/gpu/drm/radeon/radeon_device.c | 20 +++++++++++--------- drivers/gpu/drm/radeon/radeon_gem.c | 4 ++-- drivers/gpu/drm/radeon/radeon_ttm.c | 4 ++-- drivers/gpu/drm/radeon/rs400.c | 4 ++-- drivers/gpu/drm/radeon/rs600.c | 2 +- drivers/gpu/drm/radeon/rs690.c | 7 ++++--- drivers/gpu/drm/radeon/rv515.c | 7 ++----- drivers/gpu/drm/radeon/rv770.c | 2 +- 12 files changed, 56 insertions(+), 42 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 0e00fef0b84f..05a44896dffb 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -173,8 +173,12 @@ void r100_mc_setup(struct radeon_device *rdev) DRM_ERROR("Failed to register debugfs file for R100 MC !\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + /* Novell bug 204882 for RN50/M6/M7 with 8/16/32MB VRAM, + * if the aperture is 64MB but we have 32MB VRAM + * we report only 32MB VRAM but we have to set MC_FB_LOCATION + * to 64MB, otherwise the gpu accidentially dies */ + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16); WREG32(RADEON_MC_FB_LOCATION, tmp); @@ -1447,25 +1451,28 @@ void r100_vram_init_sizes(struct radeon_device *rdev) uint32_t tom; /* read NB_TOM to get the amount of ram stolen for the GPU */ tom = RREG32(RADEON_NB_TOM); - rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); + rdev->mc.real_vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16); /* for IGPs we need to keep VRAM where it was put by the BIOS */ rdev->mc.vram_location = (tom & 0xffff) << 16; - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; } else { - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE); /* Some production boards of m6 will report 0 * if it's 8 MB */ - if (rdev->mc.vram_size == 0) { - rdev->mc.vram_size = 8192 * 1024; - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + if (rdev->mc.real_vram_size == 0) { + rdev->mc.real_vram_size = 8192 * 1024; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); } /* let driver place VRAM */ rdev->mc.vram_location = 0xFFFFFFFFUL; /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - * Novell bug 204882 + along with lots of ubuntu ones */ - if (config_aper_size > rdev->mc.vram_size) - rdev->mc.vram_size = config_aper_size; + if (config_aper_size > rdev->mc.real_vram_size) + rdev->mc.mc_vram_size = config_aper_size; + else + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; } /* work out accessible VRAM */ @@ -1477,8 +1484,11 @@ void r100_vram_init_sizes(struct radeon_device *rdev) if (accessible > rdev->mc.aper_size) accessible = rdev->mc.aper_size; - if (rdev->mc.vram_size > rdev->mc.aper_size) - rdev->mc.vram_size = rdev->mc.aper_size; + if (rdev->mc.mc_vram_size > rdev->mc.aper_size) + rdev->mc.mc_vram_size = rdev->mc.aper_size; + + if (rdev->mc.real_vram_size > rdev->mc.aper_size) + rdev->mc.real_vram_size = rdev->mc.aper_size; } void r100_vram_info(struct radeon_device *rdev) diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c index 0a981e2ee2f8..09fb0b6ec7dd 100644 --- a/drivers/gpu/drm/radeon/r520.c +++ b/drivers/gpu/drm/radeon/r520.c @@ -95,8 +95,8 @@ int r520_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R520_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(R520_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(R520_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c index c45559fc97fd..538cd907df69 100644 --- a/drivers/gpu/drm/radeon/r600.c +++ b/drivers/gpu/drm/radeon/r600.c @@ -67,7 +67,7 @@ int r600_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R600_MC_FB_TOP, tmp >> 24); tmp |= REG_SET(R600_MC_FB_BASE, rdev->mc.vram_location >> 24); WREG32(R600_MC_VM_FB_LOCATION, tmp); @@ -140,7 +140,8 @@ void r600_vram_get_type(struct radeon_device *rdev) void r600_vram_info(struct radeon_device *rdev) { r600_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(R600_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(R600_CONFIG_MEMSIZE); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; /* Could aper size report 0 ? */ rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 63a3fe32e584..045b33b3bf2d 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -332,8 +332,11 @@ struct radeon_mc { unsigned gtt_location; unsigned gtt_size; unsigned vram_location; - unsigned vram_size; + /* for some chips with <= 32MB we need to lie + * about vram size near mc fb location */ + unsigned mc_vram_size; unsigned vram_width; + unsigned real_vram_size; int vram_mtrr; bool vram_is_ddr; }; diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index f78db5c8008c..6d1749e44222 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -121,7 +121,7 @@ int radeon_mc_setup(struct radeon_device *rdev) if (rdev->mc.vram_location != 0xFFFFFFFFUL) { /* vram location was already setup try to put gtt after * if it fits */ - tmp = rdev->mc.vram_location + rdev->mc.vram_size; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size; tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1); if ((0xFFFFFFFFUL - tmp) >= rdev->mc.gtt_size) { rdev->mc.gtt_location = tmp; @@ -136,13 +136,13 @@ int radeon_mc_setup(struct radeon_device *rdev) } else if (rdev->mc.gtt_location != 0xFFFFFFFFUL) { /* gtt location was already setup try to put vram before * if it fits */ - if (rdev->mc.vram_size < rdev->mc.gtt_location) { + if (rdev->mc.mc_vram_size < rdev->mc.gtt_location) { rdev->mc.vram_location = 0; } else { tmp = rdev->mc.gtt_location + rdev->mc.gtt_size; - tmp += (rdev->mc.vram_size - 1); - tmp &= ~(rdev->mc.vram_size - 1); - if ((0xFFFFFFFFUL - tmp) >= rdev->mc.vram_size) { + tmp += (rdev->mc.mc_vram_size - 1); + tmp &= ~(rdev->mc.mc_vram_size - 1); + if ((0xFFFFFFFFUL - tmp) >= rdev->mc.mc_vram_size) { rdev->mc.vram_location = tmp; } else { printk(KERN_ERR "[drm] vram too big to fit " @@ -152,12 +152,14 @@ int radeon_mc_setup(struct radeon_device *rdev) } } else { rdev->mc.vram_location = 0; - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; } - DRM_INFO("radeon: VRAM %uM\n", rdev->mc.vram_size >> 20); + DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20); DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n", rdev->mc.vram_location, - rdev->mc.vram_location + rdev->mc.vram_size - 1); + rdev->mc.vram_location + rdev->mc.mc_vram_size - 1); + if (rdev->mc.real_vram_size != rdev->mc.mc_vram_size) + DRM_INFO("radeon: VRAM less than aperture workaround enabled\n"); DRM_INFO("radeon: GTT %uM\n", rdev->mc.gtt_size >> 20); DRM_INFO("radeon: GTT from 0x%08X to 0x%08X\n", rdev->mc.gtt_location, @@ -573,7 +575,7 @@ int radeon_device_init(struct radeon_device *rdev, rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size, MTRR_TYPE_WRCOMB, 1); DRM_INFO("Detected VRAM RAM=%uM, BAR=%uM\n", - rdev->mc.vram_size >> 20, + rdev->mc.real_vram_size >> 20, (unsigned)rdev->mc.aper_size >> 20); DRM_INFO("RAM width %dbits %cDR\n", rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S'); diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index 12542087b298..cded5180c752 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -157,9 +157,9 @@ int radeon_gem_info_ioctl(struct drm_device *dev, void *data, struct radeon_device *rdev = dev->dev_private; struct drm_radeon_gem_info *args = data; - args->vram_size = rdev->mc.vram_size; + args->vram_size = rdev->mc.real_vram_size; /* FIXME: report somethings that makes sense */ - args->vram_visible = rdev->mc.vram_size - (4 * 1024 * 1024); + args->vram_visible = rdev->mc.real_vram_size - (4 * 1024 * 1024); args->gart_size = rdev->mc.gtt_size; return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c index f3469b96208c..15c3531377ed 100644 --- a/drivers/gpu/drm/radeon/radeon_ttm.c +++ b/drivers/gpu/drm/radeon/radeon_ttm.c @@ -454,7 +454,7 @@ int radeon_ttm_init(struct radeon_device *rdev) return r; } r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_VRAM, 0, - ((rdev->mc.aper_size) >> PAGE_SHIFT)); + ((rdev->mc.real_vram_size) >> PAGE_SHIFT)); if (r) { DRM_ERROR("Failed initializing VRAM heap.\n"); return r; @@ -471,7 +471,7 @@ int radeon_ttm_init(struct radeon_device *rdev) return r; } DRM_INFO("radeon: %uM of VRAM memory ready\n", - rdev->mc.vram_size / (1024 * 1024)); + rdev->mc.real_vram_size / (1024 * 1024)); r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_TT, 0, ((rdev->mc.gtt_size) >> PAGE_SHIFT)); if (r) { diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c index 96a3c8486d25..b29affd9c5d8 100644 --- a/drivers/gpu/drm/radeon/rs400.c +++ b/drivers/gpu/drm/radeon/rs400.c @@ -233,7 +233,7 @@ int rs400_mc_init(struct radeon_device *rdev) rs400_gpu_init(rdev); rs400_gart_disable(rdev); - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); r = radeon_mc_setup(rdev); @@ -247,7 +247,7 @@ int rs400_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16); WREG32(RADEON_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index bccdce7fd379..bbea6dee4a94 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -223,7 +223,7 @@ int rs600_mc_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait MC idle while " "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RS600_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RS600_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(RS600_MC_FB_LOCATION, tmp); diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 97eaee3d28b8..839595b00728 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -67,7 +67,7 @@ int rs690_mc_init(struct radeon_device *rdev) rs400_gart_disable(rdev); /* Setup GPU memory space */ - rdev->mc.gtt_location = rdev->mc.vram_size; + rdev->mc.gtt_location = rdev->mc.mc_vram_size; rdev->mc.gtt_location += (rdev->mc.gtt_size - 1); rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1); rdev->mc.vram_location = 0xFFFFFFFFUL; @@ -82,7 +82,7 @@ int rs690_mc_init(struct radeon_device *rdev) printk(KERN_WARNING "Failed to wait MC idle while " "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(RS690_MC_FB_TOP, tmp >> 16); tmp |= REG_SET(RS690_MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(RS690_MCCFG_FB_LOCATION, tmp); @@ -228,7 +228,8 @@ void rs690_vram_info(struct radeon_device *rdev) } else { rdev->mc.vram_width = 64; } - rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE); + rdev->mc.mc_vram_size = rdev->mc.real_vram_size; rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 4fd411893b91..551e608702e4 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -100,10 +100,10 @@ int rv515_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } /* Write VRAM size in case we are limiting it */ - WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size); + WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size); tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32(0x134, tmp); - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(MC_FB_TOP, tmp >> 16); tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16); WREG32_MC(MC_FB_LOCATION, tmp); @@ -369,10 +369,7 @@ void rv515_vram_info(struct radeon_device *rdev) fixed20_12 a; rv515_vram_get_type(rdev); - rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE); - rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0); - rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0); /* FIXME: we should enforce default clock in case GPU is not in * default setup */ diff --git a/drivers/gpu/drm/radeon/rv770.c b/drivers/gpu/drm/radeon/rv770.c index da50cc51ede3..21d8ffd57308 100644 --- a/drivers/gpu/drm/radeon/rv770.c +++ b/drivers/gpu/drm/radeon/rv770.c @@ -67,7 +67,7 @@ int rv770_mc_init(struct radeon_device *rdev) "programming pipes. Bad things might happen.\n"); } - tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1; + tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1; tmp = REG_SET(R700_MC_FB_TOP, tmp >> 24); tmp |= REG_SET(R700_MC_FB_BASE, rdev->mc.vram_location >> 24); WREG32(R700_MC_VM_FB_LOCATION, tmp); -- cgit v1.2.3 From 4677f15c60421d48566c48c3149474e64977f071 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Tue, 21 Jul 2009 17:45:13 +0200 Subject: drm/ttm: Fix an oops and sync object leak. The code was potentially dereferencig a NULL sync object pointer. At the same time a sync object reference was potentially leaked. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index bdec583901eb..3e5d0c4ad85c 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -509,8 +509,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, if (evict) { ret = ttm_bo_wait(bo, false, false, false); spin_unlock(&bo->lock); - driver->sync_obj_unref(&bo->sync_obj); - + if (tmp_obj) + driver->sync_obj_unref(&tmp_obj); if (ret) return ret; @@ -532,6 +532,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo, set_bit(TTM_BO_PRIV_FLAG_MOVING, &bo->priv_flags); spin_unlock(&bo->lock); + if (tmp_obj) + driver->sync_obj_unref(&tmp_obj); ret = ttm_buffer_object_transfer(bo, &ghost_obj); if (ret) -- cgit v1.2.3 From 542c6f6df51327dbb180cf4d9b34827e147efe17 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 24 Jul 2009 09:57:34 +0200 Subject: drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes. For x86 this affected highmem pages only, since they were always kmapped cache-coherent, and this is fixed using kmap_atomic_prot(). For other architectures that may not modify the linear kernel map we resort to vmap() for now, since kmap_atomic_prot() generally uses the linear kernel map for lowmem pages. This of course comes with a performance impact and should be optimized when possible. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 63 ++++++++++++++++++++++++++++++++------- 1 file changed, 52 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index 3e5d0c4ad85c..ce2e6f38ea01 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -136,7 +136,8 @@ static int ttm_copy_io_page(void *dst, void *src, unsigned long page) } static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, - unsigned long page) + unsigned long page, + pgprot_t prot) { struct page *d = ttm_tt_get_page(ttm, page); void *dst; @@ -145,17 +146,35 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, return -ENOMEM; src = (void *)((unsigned long)src + (page << PAGE_SHIFT)); - dst = kmap(d); + +#ifdef CONFIG_X86 + dst = kmap_atomic_prot(d, KM_USER0, prot); +#else + if (prot != PAGE_KERNEL) + dst = vmap(&d, 1, 0, prot); + else + dst = kmap(d); +#endif if (!dst) return -ENOMEM; memcpy_fromio(dst, src, PAGE_SIZE); - kunmap(d); + +#ifdef CONFIG_X86 + kunmap_atomic(dst, KM_USER0); +#else + if (prot != PAGE_KERNEL) + vunmap(dst); + else + kunmap(d); +#endif + return 0; } static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, - unsigned long page) + unsigned long page, + pgprot_t prot) { struct page *s = ttm_tt_get_page(ttm, page); void *src; @@ -164,12 +183,28 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, return -ENOMEM; dst = (void *)((unsigned long)dst + (page << PAGE_SHIFT)); - src = kmap(s); +#ifdef CONFIG_X86 + src = kmap_atomic_prot(s, KM_USER0, prot); +#else + if (prot != PAGE_KERNEL) + src = vmap(&s, 1, 0, prot); + else + src = kmap(s); +#endif if (!src) return -ENOMEM; memcpy_toio(dst, src, PAGE_SIZE); - kunmap(s); + +#ifdef CONFIG_X86 + kunmap_atomic(src, KM_USER0); +#else + if (prot != PAGE_KERNEL) + vunmap(src); + else + kunmap(s); +#endif + return 0; } @@ -214,11 +249,17 @@ int ttm_bo_move_memcpy(struct ttm_buffer_object *bo, for (i = 0; i < new_mem->num_pages; ++i) { page = i * dir + add; - if (old_iomap == NULL) - ret = ttm_copy_ttm_io_page(ttm, new_iomap, page); - else if (new_iomap == NULL) - ret = ttm_copy_io_ttm_page(ttm, old_iomap, page); - else + if (old_iomap == NULL) { + pgprot_t prot = ttm_io_prot(old_mem->placement, + PAGE_KERNEL); + ret = ttm_copy_ttm_io_page(ttm, new_iomap, page, + prot); + } else if (new_iomap == NULL) { + pgprot_t prot = ttm_io_prot(new_mem->placement, + PAGE_KERNEL); + ret = ttm_copy_io_ttm_page(ttm, old_iomap, page, + prot); + } else ret = ttm_copy_io_page(new_iomap, old_iomap, page); if (ret) goto out1; -- cgit v1.2.3 From f121ecfebbea1452a17d57c656def7d1537440f7 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 24 Jul 2009 10:22:36 +0200 Subject: drm/ttm: powerpc: Fix Highmem cache flushing. Temporarily maps highmem pages while flushing to get a valid virtual address to flush. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_tt.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 81ab81f030a3..9b2248a80cff 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -86,10 +86,16 @@ void ttm_tt_cache_flush(struct page *pages[], unsigned long num_pages) unsigned long i; for (i = 0; i < num_pages; ++i) { - if (pages[i]) { - unsigned long start = (unsigned long)page_address(pages[i]); - flush_dcache_range(start, start + PAGE_SIZE); - } + struct page *page = pages[i]; + void *page_virtual; + + if (unlikely(page == NULL)) + continue; + + page_virtual = kmap_atomic(page, KM_USER0); + flush_dcache_range((unsigned long) page_virtual, + (unsigned long) page_virtual + PAGE_SIZE); + kunmap_atomic(page_virtual, KM_USER0); } #else if (on_each_cpu(ttm_tt_ipi_handler, NULL, 1) != 0) -- cgit v1.2.3 From 3b170c3b2e688665fbc2845ba5bb4304bf38a119 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 24 Jul 2009 13:47:45 +1000 Subject: drm/radeon/kms: allow interruptible waits for objects. Blocking here isn't something the X server mouse appreciates, avoid the block and let userspace retry the waits. libdrm_radeon userspace library is also expecting EBUSY not ERESTART Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fence.c | 2 +- drivers/gpu/drm/radeon/radeon_object.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_fence.c b/drivers/gpu/drm/radeon/radeon_fence.c index 96afbf5ae2ad..b4e48dd2e859 100644 --- a/drivers/gpu/drm/radeon/radeon_fence.c +++ b/drivers/gpu/drm/radeon/radeon_fence.c @@ -195,7 +195,7 @@ retry: r = wait_event_interruptible_timeout(rdev->fence_drv.queue, radeon_fence_signaled(fence), timeout); if (unlikely(r == -ERESTARTSYS)) { - return -ERESTART; + return -EBUSY; } } else { r = wait_event_timeout(rdev->fence_drv.queue, diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index 81573c3a9b43..dd9ac2fed6d6 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -309,7 +309,7 @@ int radeon_object_wait(struct radeon_object *robj) } spin_lock(&robj->tobj.lock); if (robj->tobj.sync_obj) { - r = ttm_bo_wait(&robj->tobj, true, false, false); + r = ttm_bo_wait(&robj->tobj, true, true, false); } spin_unlock(&robj->tobj.lock); radeon_object_unreserve(robj); -- cgit v1.2.3 From ecc0b32645bf19a3a240e72be3022ab3b46ad3d0 Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Tue, 21 Jul 2009 11:23:57 +0200 Subject: drm/radeon: Add radeon.test parameter for running BO GPU copy tests. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If enabled, during initialization BO GTT->VRAM and VRAM->GTT GPU copies are tested across the whole GTT aperture. This has helped uncover the benchmark copy size bug and verify the maximum aperture size supported by the AGP bridge in my PowerBook. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/Makefile | 3 +- drivers/gpu/drm/radeon/radeon.h | 7 ++ drivers/gpu/drm/radeon/radeon_device.c | 3 + drivers/gpu/drm/radeon/radeon_drv.c | 4 + drivers/gpu/drm/radeon/radeon_test.c | 209 +++++++++++++++++++++++++++++++++ 5 files changed, 225 insertions(+), 1 deletion(-) create mode 100644 drivers/gpu/drm/radeon/radeon_test.c (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/Makefile b/drivers/gpu/drm/radeon/Makefile index 5fae1e074b4b..013d38059943 100644 --- a/drivers/gpu/drm/radeon/Makefile +++ b/drivers/gpu/drm/radeon/Makefile @@ -13,7 +13,8 @@ radeon-$(CONFIG_DRM_RADEON_KMS) += radeon_device.o radeon_kms.o \ radeon_encoders.o radeon_display.o radeon_cursor.o radeon_i2c.o \ radeon_clocks.o radeon_fb.o radeon_gem.o radeon_ring.o radeon_irq_kms.o \ radeon_cs.o radeon_bios.o radeon_benchmark.o r100.o r300.o r420.o \ - rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o + rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o \ + radeon_test.o radeon-$(CONFIG_COMPAT) += radeon_ioc32.o diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 045b33b3bf2d..b1d945b8ed6c 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -64,6 +64,7 @@ extern int radeon_agpmode; extern int radeon_vram_limit; extern int radeon_gart_size; extern int radeon_benchmarking; +extern int radeon_testing; extern int radeon_connector_table; /* @@ -534,6 +535,12 @@ struct radeon_pm { void radeon_benchmark(struct radeon_device *rdev); +/* + * Testing + */ +void radeon_test_moves(struct radeon_device *rdev); + + /* * Debugfs */ diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 6d1749e44222..a162ade74b7f 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -638,6 +638,9 @@ int radeon_device_init(struct radeon_device *rdev, if (!ret) { DRM_INFO("radeon: kernel modesetting successfully initialized.\n"); } + if (radeon_testing) { + radeon_test_moves(rdev); + } if (radeon_benchmarking) { radeon_benchmark(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c index 84ba69f48784..3cfcee17dc56 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.c +++ b/drivers/gpu/drm/radeon/radeon_drv.c @@ -89,6 +89,7 @@ int radeon_agpmode = 0; int radeon_vram_limit = 0; int radeon_gart_size = 512; /* default gart size */ int radeon_benchmarking = 0; +int radeon_testing = 0; int radeon_connector_table = 0; #endif @@ -117,6 +118,9 @@ module_param_named(gartsize, radeon_gart_size, int, 0600); MODULE_PARM_DESC(benchmark, "Run benchmark"); module_param_named(benchmark, radeon_benchmarking, int, 0444); +MODULE_PARM_DESC(test, "Run tests"); +module_param_named(test, radeon_testing, int, 0444); + MODULE_PARM_DESC(connector_table, "Force connector table"); module_param_named(connector_table, radeon_connector_table, int, 0444); #endif diff --git a/drivers/gpu/drm/radeon/radeon_test.c b/drivers/gpu/drm/radeon/radeon_test.c new file mode 100644 index 000000000000..03c33cf4e14c --- /dev/null +++ b/drivers/gpu/drm/radeon/radeon_test.c @@ -0,0 +1,209 @@ +/* + * Copyright 2009 VMware, Inc. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * Authors: Michel Dänzer + */ +#include +#include +#include "radeon_reg.h" +#include "radeon.h" + + +/* Test BO GTT->VRAM and VRAM->GTT GPU copies across the whole GTT aperture */ +void radeon_test_moves(struct radeon_device *rdev) +{ + struct radeon_object *vram_obj = NULL; + struct radeon_object **gtt_obj = NULL; + struct radeon_fence *fence = NULL; + uint64_t gtt_addr, vram_addr; + unsigned i, n, size; + int r; + + size = 1024 * 1024; + + /* Number of tests = + * (Total GTT - IB pool - writeback page - ring buffer) / test size + */ + n = (rdev->mc.gtt_size - RADEON_IB_POOL_SIZE*64*1024 - 4096 - + rdev->cp.ring_size) / size; + + gtt_obj = kzalloc(n * sizeof(*gtt_obj), GFP_KERNEL); + if (!gtt_obj) { + DRM_ERROR("Failed to allocate %d pointers\n", n); + r = 1; + goto out_cleanup; + } + + r = radeon_object_create(rdev, NULL, size, true, RADEON_GEM_DOMAIN_VRAM, + false, &vram_obj); + if (r) { + DRM_ERROR("Failed to create VRAM object\n"); + goto out_cleanup; + } + + r = radeon_object_pin(vram_obj, RADEON_GEM_DOMAIN_VRAM, &vram_addr); + if (r) { + DRM_ERROR("Failed to pin VRAM object\n"); + goto out_cleanup; + } + + for (i = 0; i < n; i++) { + void *gtt_map, *vram_map; + void **gtt_start, **gtt_end; + void **vram_start, **vram_end; + + r = radeon_object_create(rdev, NULL, size, true, + RADEON_GEM_DOMAIN_GTT, false, gtt_obj + i); + if (r) { + DRM_ERROR("Failed to create GTT object %d\n", i); + goto out_cleanup; + } + + r = radeon_object_pin(gtt_obj[i], RADEON_GEM_DOMAIN_GTT, >t_addr); + if (r) { + DRM_ERROR("Failed to pin GTT object %d\n", i); + goto out_cleanup; + } + + r = radeon_object_kmap(gtt_obj[i], >t_map); + if (r) { + DRM_ERROR("Failed to map GTT object %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size; + gtt_start < gtt_end; + gtt_start++) + *gtt_start = gtt_start; + + radeon_object_kunmap(gtt_obj[i]); + + r = radeon_fence_create(rdev, &fence); + if (r) { + DRM_ERROR("Failed to create GTT->VRAM fence %d\n", i); + goto out_cleanup; + } + + r = radeon_copy(rdev, gtt_addr, vram_addr, size / 4096, fence); + if (r) { + DRM_ERROR("Failed GTT->VRAM copy %d\n", i); + goto out_cleanup; + } + + r = radeon_fence_wait(fence, false); + if (r) { + DRM_ERROR("Failed to wait for GTT->VRAM fence %d\n", i); + goto out_cleanup; + } + + radeon_fence_unref(&fence); + + r = radeon_object_kmap(vram_obj, &vram_map); + if (r) { + DRM_ERROR("Failed to map VRAM object after copy %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size, + vram_start = vram_map, vram_end = vram_map + size; + vram_start < vram_end; + gtt_start++, vram_start++) { + if (*vram_start != gtt_start) { + DRM_ERROR("Incorrect GTT->VRAM copy %d: Got 0x%p, " + "expected 0x%p (GTT map 0x%p-0x%p)\n", + i, *vram_start, gtt_start, gtt_map, + gtt_end); + radeon_object_kunmap(vram_obj); + goto out_cleanup; + } + *vram_start = vram_start; + } + + radeon_object_kunmap(vram_obj); + + r = radeon_fence_create(rdev, &fence); + if (r) { + DRM_ERROR("Failed to create VRAM->GTT fence %d\n", i); + goto out_cleanup; + } + + r = radeon_copy(rdev, vram_addr, gtt_addr, size / 4096, fence); + if (r) { + DRM_ERROR("Failed VRAM->GTT copy %d\n", i); + goto out_cleanup; + } + + r = radeon_fence_wait(fence, false); + if (r) { + DRM_ERROR("Failed to wait for VRAM->GTT fence %d\n", i); + goto out_cleanup; + } + + radeon_fence_unref(&fence); + + r = radeon_object_kmap(gtt_obj[i], >t_map); + if (r) { + DRM_ERROR("Failed to map GTT object after copy %d\n", i); + goto out_cleanup; + } + + for (gtt_start = gtt_map, gtt_end = gtt_map + size, + vram_start = vram_map, vram_end = vram_map + size; + gtt_start < gtt_end; + gtt_start++, vram_start++) { + if (*gtt_start != vram_start) { + DRM_ERROR("Incorrect VRAM->GTT copy %d: Got 0x%p, " + "expected 0x%p (VRAM map 0x%p-0x%p)\n", + i, *gtt_start, vram_start, vram_map, + vram_end); + radeon_object_kunmap(gtt_obj[i]); + goto out_cleanup; + } + } + + radeon_object_kunmap(gtt_obj[i]); + + DRM_INFO("Tested GTT->VRAM and VRAM->GTT copy for GTT offset 0x%llx\n", + gtt_addr - rdev->mc.gtt_location); + } + +out_cleanup: + if (vram_obj) { + radeon_object_unpin(vram_obj); + radeon_object_unref(&vram_obj); + } + if (gtt_obj) { + for (i = 0; i < n; i++) { + if (gtt_obj[i]) { + radeon_object_unpin(gtt_obj[i]); + radeon_object_unref(>t_obj[i]); + } + } + kfree(gtt_obj); + } + if (fence) { + radeon_fence_unref(&fence); + } + if (r) { + printk(KERN_WARNING "Error while testing BO move.\n"); + } +} + -- cgit v1.2.3 From ea3c13bd8c2ed1d3670bd72e60f562a427355fdf Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Mon, 20 Jul 2009 01:44:03 +0200 Subject: drm/radeon: Fix size used for benchmarking BO copies. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The incorrect size caused benchmark results to be inflated by a factor of 4. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_benchmark.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_benchmark.c b/drivers/gpu/drm/radeon/radeon_benchmark.c index c44403a2ca76..2e938f7496fb 100644 --- a/drivers/gpu/drm/radeon/radeon_benchmark.c +++ b/drivers/gpu/drm/radeon/radeon_benchmark.c @@ -63,7 +63,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize, if (r) { goto out_cleanup; } - r = radeon_copy_dma(rdev, saddr, daddr, size >> 14, fence); + r = radeon_copy_dma(rdev, saddr, daddr, size / 4096, fence); if (r) { goto out_cleanup; } @@ -88,7 +88,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize, if (r) { goto out_cleanup; } - r = radeon_copy_blit(rdev, saddr, daddr, size >> 14, fence); + r = radeon_copy_blit(rdev, saddr, daddr, size / 4096, fence); if (r) { goto out_cleanup; } -- cgit v1.2.3 From b42db2b12df7b4f7b2ace581a7726cb5bcb2d658 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 29 Jul 2009 16:56:52 +1000 Subject: drm/ttm: fix highuser vs dma32 confusion. DMA32 and highmem are sort of exclusive. Noticed by AndrewR on #radeon. Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_tt.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c index 9b2248a80cff..b8b6c4a5f983 100644 --- a/drivers/gpu/drm/ttm/ttm_tt.c +++ b/drivers/gpu/drm/ttm/ttm_tt.c @@ -137,13 +137,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm) static struct page *ttm_tt_alloc_page(unsigned page_flags) { - gfp_t gfp_flags = GFP_HIGHUSER; + gfp_t gfp_flags = GFP_USER; if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC) gfp_flags |= __GFP_ZERO; if (page_flags & TTM_PAGE_FLAG_DMA32) gfp_flags |= __GFP_DMA32; + else + gfp_flags |= __GFP_HIGHMEM; return alloc_page(gfp_flags); } -- cgit v1.2.3 From ed8f0d9e708a1a7c9222e7d0a35d97521e904223 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 29 Jul 2009 17:07:38 +1000 Subject: drm/radeon: set fb aperture sizes for framebuffer handoff. This will allow efi/vesa to handoff to radeon. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 36d2f5588f20..3206c0ad7b6c 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -602,6 +602,11 @@ int radeonfb_create(struct radeon_device *rdev, info->var.width = -1; info->var.xres = fb_width; info->var.yres = fb_height; + + /* setup aperture base/size for vesafb takeover */ + info->aperture_base = rdev->ddev->mode_config.fb_base; + info->aperture_size = rdev->mc.real_vram_size; + info->fix.mmio_start = 0; info->fix.mmio_len = 0; info->pixmap.size = 64*1024; -- cgit v1.2.3 From 430453fc2a5f3f2c1d98ebc3c3d4c54f3060e3c3 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 28 Jul 2009 09:59:47 +0200 Subject: libertas: Read outside array bounds reads bss->rates[j] before checking bounds of index, and should use ARRAY_SIZE to determine the size of the array. Signed-off-by: Roel Kluin Acked-by: Holger Schurig Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/scan.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/scan.c b/drivers/net/wireless/libertas/scan.c index 601b54249677..6c95af3023cc 100644 --- a/drivers/net/wireless/libertas/scan.c +++ b/drivers/net/wireless/libertas/scan.c @@ -5,6 +5,7 @@ * for sending scan commands to the firmware. */ #include +#include #include #include #include @@ -876,7 +877,7 @@ static inline char *lbs_translate_scan(struct lbs_private *priv, iwe.u.bitrate.disabled = 0; iwe.u.bitrate.value = 0; - for (j = 0; bss->rates[j] && (j < sizeof(bss->rates)); j++) { + for (j = 0; j < ARRAY_SIZE(bss->rates) && bss->rates[j]; j++) { /* Bit rate given in 500 kb/s units */ iwe.u.bitrate.value = bss->rates[j] * 500000; current_val = iwe_stream_add_value(info, start, current_val, -- cgit v1.2.3 From 57921c312e8cef72ba35a4cfe870b376da0b1b87 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 28 Jul 2009 12:05:00 +0200 Subject: libertas: Read buffer overflow Several arrays were read before checking whether the index was within bounds. ARRAY_SIZE() should be used to determine the size of arrays. rates->rates has an arraysize of 1, so calling get_common_rates() with a rates_size of MAX_RATES (14) was causing reads out of bounds. tmp_size can increment at most to (ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1), so that should be the number of elements of tmp[]. A goto can be eliminated: ret was already set upon its declaration. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/assoc.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c index b9b374119033..d6997371c27e 100644 --- a/drivers/net/wireless/libertas/assoc.c +++ b/drivers/net/wireless/libertas/assoc.c @@ -1,6 +1,7 @@ /* Copyright (C) 2006, Red Hat, Inc. */ #include +#include #include #include #include @@ -43,21 +44,21 @@ static int get_common_rates(struct lbs_private *priv, u16 *rates_size) { u8 *card_rates = lbs_bg_rates; - size_t num_card_rates = sizeof(lbs_bg_rates); int ret = 0, i, j; - u8 tmp[30]; + u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)]; size_t tmp_size = 0; /* For each rate in card_rates that exists in rate1, copy to tmp */ - for (i = 0; card_rates[i] && (i < num_card_rates); i++) { - for (j = 0; rates[j] && (j < *rates_size); j++) { + for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) { + for (j = 0; j < *rates_size && rates[j]; j++) { if (rates[j] == card_rates[i]) tmp[tmp_size++] = card_rates[i]; } } lbs_deb_hex(LBS_DEB_JOIN, "AP rates ", rates, *rates_size); - lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, num_card_rates); + lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, + ARRAY_SIZE(lbs_bg_rates)); lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size); lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate); @@ -69,10 +70,7 @@ static int get_common_rates(struct lbs_private *priv, lbs_pr_alert("Previously set fixed data rate %#x isn't " "compatible with the network.\n", priv->cur_rate); ret = -1; - goto done; } - ret = 0; - done: memset(rates, 0, *rates_size); *rates_size = min_t(int, tmp_size, *rates_size); @@ -322,7 +320,7 @@ static int lbs_associate(struct lbs_private *priv, rates = (struct mrvl_ie_rates_param_set *) pos; rates->header.type = cpu_to_le16(TLV_TYPE_RATES); memcpy(&rates->rates, &bss->rates, MAX_RATES); - tmplen = MAX_RATES; + tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES); if (get_common_rates(priv, rates->rates, &tmplen)) { ret = -1; goto done; @@ -598,7 +596,7 @@ static int lbs_adhoc_join(struct lbs_private *priv, /* Copy Data rates from the rates recorded in scan response */ memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates)); - ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES); + ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES); memcpy(cmd.bss.rates, bss->rates, ratesize); if (get_common_rates(priv, cmd.bss.rates, &ratesize)) { lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n"); -- cgit v1.2.3 From ec79be26875f6c1468784876cb99192b7f41c7a5 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Wed, 29 Jul 2009 21:07:47 +0200 Subject: PM / ACPI: HP G7000 Notebook needs a SCI_EN resume quirk This fixes regression (battery "vanishing" on resume) introduced by commit d0c71fe7ebc180f1b7bc7da1d39a07fc19eec768 ("ACPI Suspend: Enable ACPI during resume if SCI_EN is not set") and also the issue with the "screaming" IRQ 9. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13745 Reported-and-tested-by: Alan Jenkins Cc: stable@kernel.org Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Len Brown Signed-off-by: Rafael J. Wysocki --- drivers/acpi/sleep.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c index 01574a066534..42159a28f433 100644 --- a/drivers/acpi/sleep.c +++ b/drivers/acpi/sleep.c @@ -397,6 +397,14 @@ static struct dmi_system_id __initdata acpisleep_dmi_table[] = { }, }, { + .callback = init_set_sci_en_on_resume, + .ident = "Hewlett-Packard HP G7000 Notebook PC", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"), + DMI_MATCH(DMI_PRODUCT_NAME, "HP G7000 Notebook PC"), + }, + }, + { .callback = init_old_suspend_ordering, .ident = "Panasonic CF51-2L", .matches = { -- cgit v1.2.3 From e043e42bdb66885b3ac10d27a01ccb9972e2b0a3 Mon Sep 17 00:00:00 2001 From: OGAWA Hirofumi Date: Wed, 29 Jul 2009 12:15:56 -0700 Subject: pty: avoid forcing 'low_latency' tty flag We really don't want to mark the pty as a low-latency device, because as Alan points out, the ->write method can be called from an IRQ (ppp?), and that means we can't use ->low_latency=1 as we take mutexes in the low_latency case. So rather than using low_latency to force the written data to be pushed to the ldisc handling at 'write()' time, just make the reader side (or the poll function) do the flush when it checks whether there is data to be had. This also fixes the problem with lost data in an emacs compile buffer (bugzilla 13815), and we can thus revert the low_latency pty hack (commit 3a54297478e6578f96fd54bf4daa1751130aca86: "pty: quickfix for the pty ENXIO timing problems"). Signed-off-by: OGAWA Hirofumi Tested-by: Aneesh Kumar K.V [ Modified to do the tty_flush_to_ldisc() inside input_available_p() so that it triggers for both read and poll() - Linus] Signed-off-by: Linus Torvalds --- drivers/char/n_tty.c | 1 + drivers/char/pty.c | 2 -- drivers/char/tty_buffer.c | 13 +++++++++++++ include/linux/tty.h | 1 + 4 files changed, 15 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/char/n_tty.c b/drivers/char/n_tty.c index ff47907ff1bf..973be2f44195 100644 --- a/drivers/char/n_tty.c +++ b/drivers/char/n_tty.c @@ -1583,6 +1583,7 @@ static int n_tty_open(struct tty_struct *tty) static inline int input_available_p(struct tty_struct *tty, int amt) { + tty_flush_to_ldisc(tty); if (tty->icanon) { if (tty->canon_data) return 1; diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 3850a68f265a..6e6942c45f5b 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -52,7 +52,6 @@ static void pty_close(struct tty_struct *tty, struct file *filp) return; tty->link->packet = 0; set_bit(TTY_OTHER_CLOSED, &tty->link->flags); - tty_flip_buffer_push(tty->link); wake_up_interruptible(&tty->link->read_wait); wake_up_interruptible(&tty->link->write_wait); if (tty->driver->subtype == PTY_TYPE_MASTER) { @@ -208,7 +207,6 @@ static int pty_open(struct tty_struct *tty, struct file *filp) clear_bit(TTY_OTHER_CLOSED, &tty->link->flags); set_bit(TTY_THROTTLED, &tty->flags); retval = 0; - tty->low_latency = 1; out: return retval; } diff --git a/drivers/char/tty_buffer.c b/drivers/char/tty_buffer.c index 810ee25d66a4..3108991c5c8b 100644 --- a/drivers/char/tty_buffer.c +++ b/drivers/char/tty_buffer.c @@ -461,6 +461,19 @@ static void flush_to_ldisc(struct work_struct *work) tty_ldisc_deref(disc); } +/** + * tty_flush_to_ldisc + * @tty: tty to push + * + * Push the terminal flip buffers to the line discipline. + * + * Must not be called from IRQ context. + */ +void tty_flush_to_ldisc(struct tty_struct *tty) +{ + flush_to_ldisc(&tty->buf.work.work); +} + /** * tty_flip_buffer_push - terminal * @tty: tty to push diff --git a/include/linux/tty.h b/include/linux/tty.h index 1488d8c81aac..e8c6c9136c97 100644 --- a/include/linux/tty.h +++ b/include/linux/tty.h @@ -394,6 +394,7 @@ extern void __do_SAK(struct tty_struct *tty); extern void disassociate_ctty(int priv); extern void no_tty(void); extern void tty_flip_buffer_push(struct tty_struct *tty); +extern void tty_flush_to_ldisc(struct tty_struct *tty); extern void tty_buffer_free_all(struct tty_struct *tty); extern void tty_buffer_flush(struct tty_struct *tty); extern void tty_buffer_init(struct tty_struct *tty); -- cgit v1.2.3 From cdaa052b05e26d96a990af5d253fd2af5db2b1fc Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Tue, 28 Jul 2009 10:54:13 +0800 Subject: drm/I915: Fix offset to DVO timings in LVDS data Now the DVO timing in LVDS data entry is obtained by using the following step: a. get the entry size for every LVDS panel data b. Get the LVDS fp entry for the preferred panel type c. get the DVO timing by using entry->dvo_timing In our driver the entry->dvo_timing is related with the size of lvds_fp_timing. For example: the size is 46. But it seems that the size of lvds_fp_timing varies on the differnt platform. In such case we will get the incorrect DVO timing entry because of the incorrect DVO offset in LVDS panel data entry. This also removes a hack on new IGDNG to get proper DVO timing. Calculate the DVO timing offset in LVDS data entry to get the DVO timing a. get the DVO timing offset in the LVDS fp data entry by using the pointer definition in LVDS data ptr b. get the LVDS data entry c. get the DVO timing by adding the DVO timing offset to data entry https://bugs.freedesktop.org/show_bug.cgi?id=22787 Signed-off-by: Zhao Yakui Tested-by: Zhenyu Wang Acked-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_bios.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c index 7cc447191028..5c7a62a96ae7 100644 --- a/drivers/gpu/drm/i915/intel_bios.c +++ b/drivers/gpu/drm/i915/intel_bios.c @@ -97,14 +97,13 @@ static void parse_lfp_panel_data(struct drm_i915_private *dev_priv, struct bdb_header *bdb) { - struct drm_device *dev = dev_priv->dev; struct bdb_lvds_options *lvds_options; struct bdb_lvds_lfp_data *lvds_lfp_data; struct bdb_lvds_lfp_data_ptrs *lvds_lfp_data_ptrs; struct bdb_lvds_lfp_data_entry *entry; struct lvds_dvo_timing *dvo_timing; struct drm_display_mode *panel_fixed_mode; - int lfp_data_size; + int lfp_data_size, dvo_timing_offset; /* Defaults if we can't find VBT info */ dev_priv->lvds_dither = 0; @@ -133,14 +132,16 @@ parse_lfp_panel_data(struct drm_i915_private *dev_priv, entry = (struct bdb_lvds_lfp_data_entry *) ((uint8_t *)lvds_lfp_data->data + (lfp_data_size * lvds_options->panel_type)); + dvo_timing_offset = lvds_lfp_data_ptrs->ptr[0].dvo_timing_offset - + lvds_lfp_data_ptrs->ptr[0].fp_timing_offset; - /* On IGDNG mobile, LVDS data block removes panel fitting registers. - So dec 2 dword from dvo_timing offset */ - if (IS_IGDNG(dev)) - dvo_timing = (struct lvds_dvo_timing *) - ((u8 *)&entry->dvo_timing - 8); - else - dvo_timing = &entry->dvo_timing; + /* + * the size of fp_timing varies on the different platform. + * So calculate the DVO timing relative offset in LVDS data + * entry to get the DVO timing entry + */ + dvo_timing = (struct lvds_dvo_timing *) + ((unsigned char *)entry + dvo_timing_offset); panel_fixed_mode = kzalloc(sizeof(*panel_fixed_mode), GFP_KERNEL); -- cgit v1.2.3 From 24f119c769bacac5729297b682fec7811a983cc6 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:28 +0800 Subject: drm/i915: disable VGA plane reliably This does VGA disable like DDX driver. SR01 bit 5 should be set before VGA plane disable through control register, otherwise we might get random crash and lockups. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 28 +++++++++++++++++++++++++--- 1 file changed, 25 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index a58bfadabd6f..b06364ed2591 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -998,6 +998,29 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y, return 0; } +/* Disable the VGA plane that we never use */ +static void i915_disable_vga (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u8 sr1; + u32 vga_reg; + + if (IS_IGDNG(dev)) + vga_reg = CPU_VGACNTRL; + else + vga_reg = VGACNTRL; + + if (I915_READ(vga_reg) & VGA_DISP_DISABLE) + return; + + I915_WRITE8(VGA_SR_INDEX, 1); + sr1 = I915_READ8(VGA_SR_DATA); + I915_WRITE8(VGA_SR_DATA, sr1 | (1 << 5)); + udelay(100); + + I915_WRITE(vga_reg, VGA_DISP_DISABLE); +} + static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) { struct drm_device *dev = crtc->dev; @@ -1200,8 +1223,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) case DRM_MODE_DPMS_OFF: DRM_DEBUG("crtc %d dpms off\n", pipe); - /* Disable the VGA plane that we never use */ - I915_WRITE(CPU_VGACNTRL, VGA_DISP_DISABLE); + i915_disable_vga(dev); /* Disable display plane */ temp = I915_READ(dspcntr_reg); @@ -1342,7 +1364,7 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode) //intel_crtc_dpms_video(crtc, FALSE); TODO /* Disable the VGA plane that we never use */ - I915_WRITE(VGACNTRL, VGA_DISP_DISABLE); + i915_disable_vga(dev); /* Disable display plane */ temp = I915_READ(dspcntr_reg); -- cgit v1.2.3 From 249c0e64c24bf455a4e4815f72750f2b16cedd94 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:29 +0800 Subject: drm/i915: fix issue in display pipe setup on IGDNG During pipe DPMS off, instead of busy waiting pipe off, insert delays during wait and don't loop after enough tries which matches spec requirement. Also try to match DPMS on path by disable FDI TX PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger the update. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_display.c | 56 ++++++++++++++++++++++++++++-------- 2 files changed, 46 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 897a116cad14..7c77c4c53c52 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1848,6 +1848,8 @@ #define PFA_CTL_1 0x68080 #define PFB_CTL_1 0x68880 #define PF_ENABLE (1<<31) +#define PFA_WIN_SZ 0x68074 +#define PFB_WIN_SZ 0x68874 /* legacy palette */ #define LGC_PALETTE_A 0x4a000 diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index b06364ed2591..15a8c3908acb 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -1038,6 +1038,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) int fdi_rx_imr_reg = (pipe == 0) ? FDI_RXA_IMR : FDI_RXB_IMR; int transconf_reg = (pipe == 0) ? TRANSACONF : TRANSBCONF; int pf_ctl_reg = (pipe == 0) ? PFA_CTL_1 : PFB_CTL_1; + int pf_win_size = (pipe == 0) ? PFA_WIN_SZ : PFB_WIN_SZ; int cpu_htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B; int cpu_hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B; int cpu_hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B; @@ -1051,7 +1052,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) int trans_vblank_reg = (pipe == 0) ? TRANS_VBLANK_A : TRANS_VBLANK_B; int trans_vsync_reg = (pipe == 0) ? TRANS_VSYNC_A : TRANS_VSYNC_B; u32 temp; - int tries = 5, j; + int tries = 5, j, n; /* XXX: When our outputs are all unaware of DPMS modes other than off * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC. @@ -1239,19 +1240,21 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) if ((temp & PIPEACONF_ENABLE) != 0) { I915_WRITE(pipeconf_reg, temp & ~PIPEACONF_ENABLE); I915_READ(pipeconf_reg); + n = 0; /* wait for cpu pipe off, pipe state */ - while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) - ; + while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) { + n++; + if (n < 60) { + udelay(500); + continue; + } else { + DRM_DEBUG("pipe %d off delay\n", pipe); + break; + } + } } else DRM_DEBUG("crtc %d is disabled\n", pipe); - /* IGDNG-A : disable cpu panel fitter ? */ - temp = I915_READ(pf_ctl_reg); - if ((temp & PF_ENABLE) != 0) { - I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE); - I915_READ(pf_ctl_reg); - } - /* disable CPU FDI tx and PCH FDI rx */ temp = I915_READ(fdi_tx_reg); I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE); @@ -1261,6 +1264,8 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_WRITE(fdi_rx_reg, temp & ~FDI_RX_ENABLE); I915_READ(fdi_rx_reg); + udelay(100); + /* still set train pattern 1 */ temp = I915_READ(fdi_tx_reg); temp &= ~FDI_LINK_TRAIN_NONE; @@ -1272,14 +1277,25 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) temp |= FDI_LINK_TRAIN_PATTERN_1; I915_WRITE(fdi_rx_reg, temp); + udelay(100); + /* disable PCH transcoder */ temp = I915_READ(transconf_reg); if ((temp & TRANS_ENABLE) != 0) { I915_WRITE(transconf_reg, temp & ~TRANS_ENABLE); I915_READ(transconf_reg); + n = 0; /* wait for PCH transcoder off, transcoder state */ - while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) - ; + while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) { + n++; + if (n < 60) { + udelay(500); + continue; + } else { + DRM_DEBUG("transcoder %d off delay\n", pipe); + break; + } + } } /* disable PCH DPLL */ @@ -1297,6 +1313,22 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_READ(fdi_rx_reg); } + /* Disable CPU FDI TX PLL */ + temp = I915_READ(fdi_tx_reg); + if ((temp & FDI_TX_PLL_ENABLE) != 0) { + I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_PLL_ENABLE); + I915_READ(fdi_tx_reg); + udelay(100); + } + + /* Disable PF */ + temp = I915_READ(pf_ctl_reg); + if ((temp & PF_ENABLE) != 0) { + I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE); + I915_READ(pf_ctl_reg); + } + I915_WRITE(pf_win_size, 0); + /* Wait for the clocks to turn off. */ udelay(150); break; -- cgit v1.2.3 From eebc863e469cd91d96c4e3636450596ae29f0502 Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:30 +0800 Subject: drm/i915: Fix channel ending action for DP aux transaction We should use current channel 'status' bits to clear DP aux channel's done and error bits, instead of using the channel setting bits, that will set send/busy bit again to initiate new transaction. This also includes also some minor cleanup. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_dp.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 6770ae88370d..afec65c5ad8a 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -236,7 +236,7 @@ intel_dp_aux_ch(struct intel_output *intel_output, } /* Clear done status and any errors */ - I915_WRITE(ch_ctl, (ctl | + I915_WRITE(ch_ctl, (status | DP_AUX_CH_CTL_DONE | DP_AUX_CH_CTL_TIME_OUT_ERROR | DP_AUX_CH_CTL_RECEIVE_ERROR)); @@ -295,7 +295,7 @@ intel_dp_aux_native_write(struct intel_output *intel_output, return -1; msg[0] = AUX_NATIVE_WRITE << 4; msg[1] = address >> 8; - msg[2] = address; + msg[2] = address & 0xff; msg[3] = send_bytes - 1; memcpy(&msg[4], send, send_bytes); msg_bytes = send_bytes + 4; @@ -387,8 +387,8 @@ intel_dp_i2c_init(struct intel_output *intel_output, const char *name) memset(&dp_priv->adapter, '\0', sizeof (dp_priv->adapter)); dp_priv->adapter.owner = THIS_MODULE; dp_priv->adapter.class = I2C_CLASS_DDC; - strncpy (dp_priv->adapter.name, name, sizeof dp_priv->adapter.name - 1); - dp_priv->adapter.name[sizeof dp_priv->adapter.name - 1] = '\0'; + strncpy (dp_priv->adapter.name, name, sizeof(dp_priv->adapter.name) - 1); + dp_priv->adapter.name[sizeof(dp_priv->adapter.name) - 1] = '\0'; dp_priv->adapter.algo_data = &dp_priv->algo; dp_priv->adapter.dev.parent = &intel_output->base.kdev; -- cgit v1.2.3 From 5eb08b69f510fadaba77eb9a1bda0f7299c4ebcc Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:31 +0800 Subject: drm/i915: enable DisplayPort support on IGDNG Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_reg.h | 25 +++++++++ drivers/gpu/drm/i915/intel_display.c | 51 +++++++++++++++++- drivers/gpu/drm/i915/intel_dp.c | 102 ++++++++++++++++++++++++++++------- 3 files changed, 157 insertions(+), 21 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 7c77c4c53c52..4518a9489ed1 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1444,6 +1444,7 @@ #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) #define DP_SCRAMBLING_DISABLE (1 << 12) +#define DP_SCRAMBLING_DISABLE_IGDNG (1 << 7) /** limit RGB values to avoid confusing TVs */ #define DP_COLOR_RANGE_16_235 (1 << 8) @@ -2210,4 +2211,28 @@ #define PCH_PP_OFF_DELAYS 0xc720c #define PCH_PP_DIVISOR 0xc7210 +#define PCH_DP_B 0xe4100 +#define PCH_DPB_AUX_CH_CTL 0xe4110 +#define PCH_DPB_AUX_CH_DATA1 0xe4114 +#define PCH_DPB_AUX_CH_DATA2 0xe4118 +#define PCH_DPB_AUX_CH_DATA3 0xe411c +#define PCH_DPB_AUX_CH_DATA4 0xe4120 +#define PCH_DPB_AUX_CH_DATA5 0xe4124 + +#define PCH_DP_C 0xe4200 +#define PCH_DPC_AUX_CH_CTL 0xe4210 +#define PCH_DPC_AUX_CH_DATA1 0xe4214 +#define PCH_DPC_AUX_CH_DATA2 0xe4218 +#define PCH_DPC_AUX_CH_DATA3 0xe421c +#define PCH_DPC_AUX_CH_DATA4 0xe4220 +#define PCH_DPC_AUX_CH_DATA5 0xe4224 + +#define PCH_DP_D 0xe4300 +#define PCH_DPD_AUX_CH_CTL 0xe4310 +#define PCH_DPD_AUX_CH_DATA1 0xe4314 +#define PCH_DPD_AUX_CH_DATA2 0xe4318 +#define PCH_DPD_AUX_CH_DATA3 0xe431c +#define PCH_DPD_AUX_CH_DATA4 0xe4320 +#define PCH_DPD_AUX_CH_DATA5 0xe4324 + #endif /* _I915_REG_H_ */ diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 15a8c3908acb..34c50460eaa7 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -268,6 +268,9 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, static bool intel_find_pll_g4x_dp(const intel_limit_t *, struct drm_crtc *crtc, int target, int refclk, intel_clock_t *best_clock); +static bool +intel_find_pll_igdng_dp(const intel_limit_t *, struct drm_crtc *crtc, + int target, int refclk, intel_clock_t *best_clock); static const intel_limit_t intel_limits_i8xx_dvo = { .dot = { .min = I8XX_DOT_MIN, .max = I8XX_DOT_MAX }, @@ -751,6 +754,30 @@ intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, return found; } +static bool +intel_find_pll_igdng_dp(const intel_limit_t *limit, struct drm_crtc *crtc, + int target, int refclk, intel_clock_t *best_clock) +{ + struct drm_device *dev = crtc->dev; + intel_clock_t clock; + if (target < 200000) { + clock.n = 1; + clock.p1 = 2; + clock.p2 = 10; + clock.m1 = 12; + clock.m2 = 9; + } else { + clock.n = 2; + clock.p1 = 1; + clock.p2 = 10; + clock.m1 = 14; + clock.m2 = 8; + } + intel_clock(dev, refclk, &clock); + memcpy(best_clock, &clock, sizeof(intel_clock_t)); + return true; +} + static bool intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int target, int refclk, intel_clock_t *best_clock) @@ -763,6 +790,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err_most = 47; found = false; + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) + return intel_find_pll_igdng_dp(limit, crtc, target, + refclk, best_clock); + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) { if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP) @@ -2136,6 +2167,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, int lvds_reg = LVDS; u32 temp; int sdvo_pixel_multiply; + int target_clock; drm_vblank_pre_modeset(dev, pipe); @@ -2218,11 +2250,18 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, } /* FDI link */ - if (IS_IGDNG(dev)) + if (IS_IGDNG(dev)) { + /* DP over FDI requires target mode clock + instead of link clock */ + if (is_dp) + target_clock = mode->clock; + else + target_clock = adjusted_mode->clock; igdng_compute_m_n(3, 4, /* lane num 4 */ - adjusted_mode->clock, + target_clock, 270000, /* lane clock */ &m_n); + } if (IS_IGD(dev)) fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2; @@ -3050,6 +3089,8 @@ static void intel_setup_outputs(struct drm_device *dev) found = 0; if (!found) intel_hdmi_init(dev, HDMIB); + if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED)) + intel_dp_init(dev, PCH_DP_B); } if (I915_READ(HDMIC) & PORT_DETECTED) @@ -3058,6 +3099,12 @@ static void intel_setup_outputs(struct drm_device *dev) if (I915_READ(HDMID) & PORT_DETECTED) intel_hdmi_init(dev, HDMID); + if (I915_READ(PCH_DP_C) & DP_DETECTED) + intel_dp_init(dev, PCH_DP_C); + + if (I915_READ(PCH_DP_D) & DP_DETECTED) + intel_dp_init(dev, PCH_DP_D); + } else if (IS_I9XX(dev)) { int found; u32 reg; diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index afec65c5ad8a..0715911cbd84 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -206,7 +206,12 @@ intel_dp_aux_ch(struct intel_output *intel_output, * and would like to run at 2MHz. So, take the * hrawclk value and divide by 2 and use that */ - aux_clock_divider = intel_hrawclk(dev) / 2; + /* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */ + if (IS_IGDNG(dev)) + aux_clock_divider = 62; + else + aux_clock_divider = intel_hrawclk(dev) / 2; + /* Must try at least 3 times according to DP spec */ for (try = 0; try < 5; try++) { /* Load the send data into the aux channel data registers */ @@ -493,22 +498,40 @@ intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode, intel_dp_compute_m_n(3, lane_count, mode->clock, adjusted_mode->clock, &m_n); - if (intel_crtc->pipe == 0) { - I915_WRITE(PIPEA_GMCH_DATA_M, - ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | - m_n.gmch_m); - I915_WRITE(PIPEA_GMCH_DATA_N, - m_n.gmch_n); - I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m); - I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n); + if (IS_IGDNG(dev)) { + if (intel_crtc->pipe == 0) { + I915_WRITE(TRANSA_DATA_M1, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(TRANSA_DATA_N1, m_n.gmch_n); + I915_WRITE(TRANSA_DP_LINK_M1, m_n.link_m); + I915_WRITE(TRANSA_DP_LINK_N1, m_n.link_n); + } else { + I915_WRITE(TRANSB_DATA_M1, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(TRANSB_DATA_N1, m_n.gmch_n); + I915_WRITE(TRANSB_DP_LINK_M1, m_n.link_m); + I915_WRITE(TRANSB_DP_LINK_N1, m_n.link_n); + } } else { - I915_WRITE(PIPEB_GMCH_DATA_M, - ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | - m_n.gmch_m); - I915_WRITE(PIPEB_GMCH_DATA_N, - m_n.gmch_n); - I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m); - I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n); + if (intel_crtc->pipe == 0) { + I915_WRITE(PIPEA_GMCH_DATA_M, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(PIPEA_GMCH_DATA_N, + m_n.gmch_n); + I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m); + I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n); + } else { + I915_WRITE(PIPEB_GMCH_DATA_M, + ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) | + m_n.gmch_m); + I915_WRITE(PIPEB_GMCH_DATA_N, + m_n.gmch_n); + I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m); + I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n); + } } } @@ -935,6 +958,12 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP) struct drm_i915_private *dev_priv = dev->dev_private; struct intel_dp_priv *dp_priv = intel_output->dev_priv; + DP &= ~DP_LINK_TRAIN_MASK; + I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE); + POSTING_READ(dp_priv->output_reg); + + udelay(17000); + I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN); POSTING_READ(dp_priv->output_reg); } @@ -978,6 +1007,24 @@ intel_dp_check_link_status(struct intel_output *intel_output) intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration); } +static enum drm_connector_status +igdng_dp_detect(struct drm_connector *connector) +{ + struct intel_output *intel_output = to_intel_output(connector); + struct intel_dp_priv *dp_priv = intel_output->dev_priv; + enum drm_connector_status status; + + status = connector_status_disconnected; + if (intel_dp_aux_native_read(intel_output, + 0x000, dp_priv->dpcd, + sizeof (dp_priv->dpcd)) == sizeof (dp_priv->dpcd)) + { + if (dp_priv->dpcd[0] != 0) + status = connector_status_connected; + } + return status; +} + /** * Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect DP connection. * @@ -996,6 +1043,9 @@ intel_dp_detect(struct drm_connector *connector) dp_priv->has_audio = false; + if (IS_IGDNG(dev)) + return igdng_dp_detect(connector); + temp = I915_READ(PORT_HOTPLUG_EN); I915_WRITE(PORT_HOTPLUG_EN, @@ -1106,6 +1156,7 @@ intel_dp_init(struct drm_device *dev, int output_reg) struct drm_connector *connector; struct intel_output *intel_output; struct intel_dp_priv *dp_priv; + const char *name = NULL; intel_output = kcalloc(sizeof(struct intel_output) + sizeof(struct intel_dp_priv), 1, GFP_KERNEL); @@ -1139,9 +1190,22 @@ intel_dp_init(struct drm_device *dev, int output_reg) drm_sysfs_connector_add(connector); /* Set up the DDC bus. */ - intel_dp_i2c_init(intel_output, - (output_reg == DP_B) ? "DPDDC-B" : - (output_reg == DP_C) ? "DPDDC-C" : "DPDDC-D"); + switch (output_reg) { + case DP_B: + case PCH_DP_B: + name = "DPDDC-B"; + break; + case DP_C: + case PCH_DP_C: + name = "DPDDC-C"; + break; + case DP_D: + case PCH_DP_D: + name = "DPDDC-D"; + break; + } + + intel_dp_i2c_init(intel_output, name); intel_output->ddc_bus = &dp_priv->adapter; intel_output->hot_plug = intel_dp_hot_plug; -- cgit v1.2.3 From 32f9d658aee5be09ebdd28fc730630e61d0b46db Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:32 +0800 Subject: drm/i915: Add eDP support on IGDNG mobile chip This adds embedded DisplayPort support on next mobile chip which aims to replace origin LVDS port. VBT's driver feature block has been used to determine the type of current internal panel for eDP or LVDS. Currently no panel fitting support for eDP and backlight control would be added in future. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_drv.h | 2 + drivers/gpu/drm/i915/i915_reg.h | 16 ++ drivers/gpu/drm/i915/intel_bios.c | 21 ++ drivers/gpu/drm/i915/intel_bios.h | 45 ++++ drivers/gpu/drm/i915/intel_display.c | 433 ++++++++++++++++++++++------------- drivers/gpu/drm/i915/intel_dp.c | 112 ++++++++- drivers/gpu/drm/i915/intel_drv.h | 3 + drivers/gpu/drm/i915/intel_lvds.c | 4 + 8 files changed, 468 insertions(+), 168 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index b05b44dd3bf6..5f3a259d95e9 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -219,6 +219,7 @@ typedef struct drm_i915_private { unsigned int lvds_vbt:1; unsigned int int_crt_support:1; unsigned int lvds_use_ssc:1; + unsigned int edp_support:1; int lvds_ssc_freq; struct drm_i915_fence_reg fence_regs[16]; /* assume 965 */ @@ -889,6 +890,7 @@ extern int i915_wait_ring(struct drm_device * dev, int n, const char *caller); IS_I915GM(dev))) #define SUPPORTS_INTEGRATED_HDMI(dev) (IS_G4X(dev) || IS_IGDNG(dev)) #define SUPPORTS_INTEGRATED_DP(dev) (IS_G4X(dev) || IS_IGDNG(dev)) +#define SUPPORTS_EDP(dev) (IS_IGDNG_M(dev)) #define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_I965G(dev)) /* dsparb controlled by hw only */ #define DSPARB_HWCONTROL(dev) (IS_G4X(dev) || IS_IGDNG(dev)) diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 4518a9489ed1..2955083aa471 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -1395,6 +1395,7 @@ #define TV_V_CHROMA_42 0x684a8 /* Display Port */ +#define DP_A 0x64000 /* eDP */ #define DP_B 0x64100 #define DP_C 0x64200 #define DP_D 0x64300 @@ -1437,9 +1438,17 @@ /* Mystic DPCD version 1.1 special mode */ #define DP_ENHANCED_FRAMING (1 << 18) +/* eDP */ +#define DP_PLL_FREQ_270MHZ (0 << 16) +#define DP_PLL_FREQ_160MHZ (1 << 16) +#define DP_PLL_FREQ_MASK (3 << 16) + /** locked once port is enabled */ #define DP_PORT_REVERSAL (1 << 15) +/* eDP */ +#define DP_PLL_ENABLE (1 << 14) + /** sends the clock on lane 15 of the PEG for debug */ #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) @@ -1464,6 +1473,13 @@ * is 20 bytes in each direction, hence the 5 fixed * data registers */ +#define DPA_AUX_CH_CTL 0x64010 +#define DPA_AUX_CH_DATA1 0x64014 +#define DPA_AUX_CH_DATA2 0x64018 +#define DPA_AUX_CH_DATA3 0x6401c +#define DPA_AUX_CH_DATA4 0x64020 +#define DPA_AUX_CH_DATA5 0x64024 + #define DPB_AUX_CH_CTL 0x64110 #define DPB_AUX_CH_DATA1 0x64114 #define DPB_AUX_CH_DATA2 0x64118 diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c index 5c7a62a96ae7..300aee3296c2 100644 --- a/drivers/gpu/drm/i915/intel_bios.c +++ b/drivers/gpu/drm/i915/intel_bios.c @@ -296,6 +296,25 @@ parse_sdvo_device_mapping(struct drm_i915_private *dev_priv, } return; } + +static void +parse_driver_features(struct drm_i915_private *dev_priv, + struct bdb_header *bdb) +{ + struct drm_device *dev = dev_priv->dev; + struct bdb_driver_features *driver; + + /* set default for chips without eDP */ + if (!SUPPORTS_EDP(dev)) { + dev_priv->edp_support = 0; + return; + } + + driver = find_section(bdb, BDB_DRIVER_FEATURES); + if (driver && driver->lvds_config == BDB_DRIVER_FEATURE_EDP) + dev_priv->edp_support = 1; +} + /** * intel_init_bios - initialize VBIOS settings & find VBT * @dev: DRM device @@ -346,6 +365,8 @@ intel_init_bios(struct drm_device *dev) parse_lfp_panel_data(dev_priv, bdb); parse_sdvo_panel_data(dev_priv, bdb); parse_sdvo_device_mapping(dev_priv, bdb); + parse_driver_features(dev_priv, bdb); + pci_unmap_rom(pdev, bios); return 0; diff --git a/drivers/gpu/drm/i915/intel_bios.h b/drivers/gpu/drm/i915/intel_bios.h index fe72e1c225d8..0f8e5f69ac7a 100644 --- a/drivers/gpu/drm/i915/intel_bios.h +++ b/drivers/gpu/drm/i915/intel_bios.h @@ -381,6 +381,51 @@ struct bdb_sdvo_lvds_options { } __attribute__((packed)); +#define BDB_DRIVER_FEATURE_NO_LVDS 0 +#define BDB_DRIVER_FEATURE_INT_LVDS 1 +#define BDB_DRIVER_FEATURE_SDVO_LVDS 2 +#define BDB_DRIVER_FEATURE_EDP 3 + +struct bdb_driver_features { + u8 boot_dev_algorithm:1; + u8 block_display_switch:1; + u8 allow_display_switch:1; + u8 hotplug_dvo:1; + u8 dual_view_zoom:1; + u8 int15h_hook:1; + u8 sprite_in_clone:1; + u8 primary_lfp_id:1; + + u16 boot_mode_x; + u16 boot_mode_y; + u8 boot_mode_bpp; + u8 boot_mode_refresh; + + u16 enable_lfp_primary:1; + u16 selective_mode_pruning:1; + u16 dual_frequency:1; + u16 render_clock_freq:1; /* 0: high freq; 1: low freq */ + u16 nt_clone_support:1; + u16 power_scheme_ui:1; /* 0: CUI; 1: 3rd party */ + u16 sprite_display_assign:1; /* 0: secondary; 1: primary */ + u16 cui_aspect_scaling:1; + u16 preserve_aspect_ratio:1; + u16 sdvo_device_power_down:1; + u16 crt_hotplug:1; + u16 lvds_config:2; + u16 tv_hotplug:1; + u16 hdmi_config:2; + + u8 static_display:1; + u8 reserved2:7; + u16 legacy_crt_max_x; + u16 legacy_crt_max_y; + u8 legacy_crt_max_refresh; + + u8 hdmi_termination; + u8 custom_vbt_version; +} __attribute__((packed)); + bool intel_init_bios(struct drm_device *dev); /* diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 34c50460eaa7..a9f1307d32d8 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -34,6 +34,8 @@ #include "drm_crtc_helper.h" +#define HAS_eDP (intel_pipe_has_type(crtc, INTEL_OUTPUT_EDP)) + bool intel_pipe_has_type (struct drm_crtc *crtc, int type); static void intel_update_watermarks(struct drm_device *dev); @@ -601,6 +603,23 @@ bool intel_pipe_has_type (struct drm_crtc *crtc, int type) return false; } +struct drm_connector * +intel_pipe_get_output (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_mode_config *mode_config = &dev->mode_config; + struct drm_connector *l_entry, *ret = NULL; + + list_for_each_entry(l_entry, &mode_config->connector_list, head) { + if (l_entry->encoder && + l_entry->encoder->crtc == crtc) { + ret = l_entry; + break; + } + } + return ret; +} + #define INTELPllInvalid(s) do { /* DRM_DEBUG(s); */ return false; } while (0) /** * Returns whether the given set of divisors are valid for a given refclk with @@ -790,6 +809,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc, int err_most = 47; found = false; + /* eDP has only 2 clock choice, no n/m/p setting */ + if (HAS_eDP) + return true; + if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT)) return intel_find_pll_igdng_dp(limit, crtc, target, refclk, best_clock); @@ -1052,6 +1075,67 @@ static void i915_disable_vga (struct drm_device *dev) I915_WRITE(vga_reg, VGA_DISP_DISABLE); } +static void igdng_disable_pll_edp (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + DRM_DEBUG("\n"); + dpa_ctl = I915_READ(DP_A); + dpa_ctl &= ~DP_PLL_ENABLE; + I915_WRITE(DP_A, dpa_ctl); +} + +static void igdng_enable_pll_edp (struct drm_crtc *crtc) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + dpa_ctl = I915_READ(DP_A); + dpa_ctl |= DP_PLL_ENABLE; + I915_WRITE(DP_A, dpa_ctl); + udelay(200); +} + + +static void igdng_set_pll_edp (struct drm_crtc *crtc, int clock) +{ + struct drm_device *dev = crtc->dev; + struct drm_i915_private *dev_priv = dev->dev_private; + u32 dpa_ctl; + + DRM_DEBUG("eDP PLL enable for clock %d\n", clock); + dpa_ctl = I915_READ(DP_A); + dpa_ctl &= ~DP_PLL_FREQ_MASK; + + if (clock < 200000) { + u32 temp; + dpa_ctl |= DP_PLL_FREQ_160MHZ; + /* workaround for 160Mhz: + 1) program 0x4600c bits 15:0 = 0x8124 + 2) program 0x46010 bit 0 = 1 + 3) program 0x46034 bit 24 = 1 + 4) program 0x64000 bit 14 = 1 + */ + temp = I915_READ(0x4600c); + temp &= 0xffff0000; + I915_WRITE(0x4600c, temp | 0x8124); + + temp = I915_READ(0x46010); + I915_WRITE(0x46010, temp | 1); + + temp = I915_READ(0x46034); + I915_WRITE(0x46034, temp | (1 << 24)); + } else { + dpa_ctl |= DP_PLL_FREQ_270MHZ; + } + I915_WRITE(DP_A, dpa_ctl); + + udelay(500); +} + static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) { struct drm_device *dev = crtc->dev; @@ -1093,27 +1177,32 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) case DRM_MODE_DPMS_STANDBY: case DRM_MODE_DPMS_SUSPEND: DRM_DEBUG("crtc %d dpms on\n", pipe); - /* enable PCH DPLL */ - temp = I915_READ(pch_dpll_reg); - if ((temp & DPLL_VCO_ENABLE) == 0) { - I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE); - I915_READ(pch_dpll_reg); - } - - /* enable PCH FDI RX PLL, wait warmup plus DMI latency */ - temp = I915_READ(fdi_rx_reg); - I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE | - FDI_SEL_PCDCLK | - FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */ - I915_READ(fdi_rx_reg); - udelay(200); + if (HAS_eDP) { + /* enable eDP PLL */ + igdng_enable_pll_edp(crtc); + } else { + /* enable PCH DPLL */ + temp = I915_READ(pch_dpll_reg); + if ((temp & DPLL_VCO_ENABLE) == 0) { + I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE); + I915_READ(pch_dpll_reg); + } - /* Enable CPU FDI TX PLL, always on for IGDNG */ - temp = I915_READ(fdi_tx_reg); - if ((temp & FDI_TX_PLL_ENABLE) == 0) { - I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE); - I915_READ(fdi_tx_reg); - udelay(100); + /* enable PCH FDI RX PLL, wait warmup plus DMI latency */ + temp = I915_READ(fdi_rx_reg); + I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE | + FDI_SEL_PCDCLK | + FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */ + I915_READ(fdi_rx_reg); + udelay(200); + + /* Enable CPU FDI TX PLL, always on for IGDNG */ + temp = I915_READ(fdi_tx_reg); + if ((temp & FDI_TX_PLL_ENABLE) == 0) { + I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE); + I915_READ(fdi_tx_reg); + udelay(100); + } } /* Enable CPU pipe */ @@ -1132,122 +1221,126 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) I915_WRITE(dspbase_reg, I915_READ(dspbase_reg)); } - /* enable CPU FDI TX and PCH FDI RX */ - temp = I915_READ(fdi_tx_reg); - temp |= FDI_TX_ENABLE; - temp |= FDI_DP_PORT_WIDTH_X4; /* default */ - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_1; - I915_WRITE(fdi_tx_reg, temp); - I915_READ(fdi_tx_reg); + if (!HAS_eDP) { + /* enable CPU FDI TX and PCH FDI RX */ + temp = I915_READ(fdi_tx_reg); + temp |= FDI_TX_ENABLE; + temp |= FDI_DP_PORT_WIDTH_X4; /* default */ + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_1; + I915_WRITE(fdi_tx_reg, temp); + I915_READ(fdi_tx_reg); - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_1; - I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE); - I915_READ(fdi_rx_reg); + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_1; + I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE); + I915_READ(fdi_rx_reg); - udelay(150); + udelay(150); - /* Train FDI. */ - /* umask FDI RX Interrupt symbol_lock and bit_lock bit - for train result */ - temp = I915_READ(fdi_rx_imr_reg); - temp &= ~FDI_RX_SYMBOL_LOCK; - temp &= ~FDI_RX_BIT_LOCK; - I915_WRITE(fdi_rx_imr_reg, temp); - I915_READ(fdi_rx_imr_reg); - udelay(150); + /* Train FDI. */ + /* umask FDI RX Interrupt symbol_lock and bit_lock bit + for train result */ + temp = I915_READ(fdi_rx_imr_reg); + temp &= ~FDI_RX_SYMBOL_LOCK; + temp &= ~FDI_RX_BIT_LOCK; + I915_WRITE(fdi_rx_imr_reg, temp); + I915_READ(fdi_rx_imr_reg); + udelay(150); - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if ((temp & FDI_RX_BIT_LOCK) == 0) { - for (j = 0; j < tries; j++) { - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if (temp & FDI_RX_BIT_LOCK) - break; - udelay(200); - } - if (j != tries) + if ((temp & FDI_RX_BIT_LOCK) == 0) { + for (j = 0; j < tries; j++) { + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + if (temp & FDI_RX_BIT_LOCK) + break; + udelay(200); + } + if (j != tries) + I915_WRITE(fdi_rx_iir_reg, + temp | FDI_RX_BIT_LOCK); + else + DRM_DEBUG("train 1 fail\n"); + } else { I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_BIT_LOCK); - else - DRM_DEBUG("train 1 fail\n"); - } else { - I915_WRITE(fdi_rx_iir_reg, - temp | FDI_RX_BIT_LOCK); - DRM_DEBUG("train 1 ok 2!\n"); - } - temp = I915_READ(fdi_tx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_2; - I915_WRITE(fdi_tx_reg, temp); - - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - temp |= FDI_LINK_TRAIN_PATTERN_2; - I915_WRITE(fdi_rx_reg, temp); + DRM_DEBUG("train 1 ok 2!\n"); + } + temp = I915_READ(fdi_tx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_2; + I915_WRITE(fdi_tx_reg, temp); + + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + temp |= FDI_LINK_TRAIN_PATTERN_2; + I915_WRITE(fdi_rx_reg, temp); - udelay(150); + udelay(150); - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if ((temp & FDI_RX_SYMBOL_LOCK) == 0) { - for (j = 0; j < tries; j++) { - temp = I915_READ(fdi_rx_iir_reg); - DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); - if (temp & FDI_RX_SYMBOL_LOCK) - break; - udelay(200); - } - if (j != tries) { + if ((temp & FDI_RX_SYMBOL_LOCK) == 0) { + for (j = 0; j < tries; j++) { + temp = I915_READ(fdi_rx_iir_reg); + DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp); + if (temp & FDI_RX_SYMBOL_LOCK) + break; + udelay(200); + } + if (j != tries) { + I915_WRITE(fdi_rx_iir_reg, + temp | FDI_RX_SYMBOL_LOCK); + DRM_DEBUG("train 2 ok 1!\n"); + } else + DRM_DEBUG("train 2 fail\n"); + } else { I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_SYMBOL_LOCK); - DRM_DEBUG("train 2 ok 1!\n"); - } else - DRM_DEBUG("train 2 fail\n"); - } else { - I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_SYMBOL_LOCK); - DRM_DEBUG("train 2 ok 2!\n"); - } - DRM_DEBUG("train done\n"); + DRM_DEBUG("train 2 ok 2!\n"); + } + DRM_DEBUG("train done\n"); - /* set transcoder timing */ - I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg)); - I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg)); - I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg)); + /* set transcoder timing */ + I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg)); + I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg)); + I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg)); - I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg)); - I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg)); - I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg)); + I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg)); + I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg)); + I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg)); - /* enable PCH transcoder */ - temp = I915_READ(transconf_reg); - I915_WRITE(transconf_reg, temp | TRANS_ENABLE); - I915_READ(transconf_reg); + /* enable PCH transcoder */ + temp = I915_READ(transconf_reg); + I915_WRITE(transconf_reg, temp | TRANS_ENABLE); + I915_READ(transconf_reg); - while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0) - ; + while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0) + ; - /* enable normal */ + /* enable normal */ - temp = I915_READ(fdi_tx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE | - FDI_TX_ENHANCE_FRAME_ENABLE); - I915_READ(fdi_tx_reg); + temp = I915_READ(fdi_tx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE | + FDI_TX_ENHANCE_FRAME_ENABLE); + I915_READ(fdi_tx_reg); - temp = I915_READ(fdi_rx_reg); - temp &= ~FDI_LINK_TRAIN_NONE; - I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE | - FDI_RX_ENHANCE_FRAME_ENABLE); - I915_READ(fdi_rx_reg); + temp = I915_READ(fdi_rx_reg); + temp &= ~FDI_LINK_TRAIN_NONE; + I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE | + FDI_RX_ENHANCE_FRAME_ENABLE); + I915_READ(fdi_rx_reg); - /* wait one idle pattern time */ - udelay(100); + /* wait one idle pattern time */ + udelay(100); + + } intel_crtc_load_lut(crtc); @@ -1286,6 +1379,10 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode) } else DRM_DEBUG("crtc %d is disabled\n", pipe); + if (HAS_eDP) { + igdng_disable_pll_edp(crtc); + } + /* disable CPU FDI tx and PCH FDI rx */ temp = I915_READ(fdi_tx_reg); I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE); @@ -2152,6 +2249,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, u32 dpll = 0, fp = 0, dspcntr, pipeconf; bool ok, is_sdvo = false, is_dvo = false; bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false; + bool is_edp = false; struct drm_mode_config *mode_config = &dev->mode_config; struct drm_connector *connector; const intel_limit_t *limit; @@ -2199,6 +2297,9 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, case INTEL_OUTPUT_DISPLAYPORT: is_dp = true; break; + case INTEL_OUTPUT_EDP: + is_edp = true; + break; } num_outputs++; @@ -2251,16 +2352,27 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, /* FDI link */ if (IS_IGDNG(dev)) { - /* DP over FDI requires target mode clock - instead of link clock */ - if (is_dp) + int lane, link_bw; + /* eDP doesn't require FDI link, so just set DP M/N + according to current link config */ + if (is_edp) { + struct drm_connector *edp; target_clock = mode->clock; - else - target_clock = adjusted_mode->clock; - igdng_compute_m_n(3, 4, /* lane num 4 */ - target_clock, - 270000, /* lane clock */ - &m_n); + edp = intel_pipe_get_output(crtc); + intel_edp_link_config(to_intel_output(edp), + &lane, &link_bw); + } else { + /* DP over FDI requires target mode clock + instead of link clock */ + if (is_dp) + target_clock = mode->clock; + else + target_clock = adjusted_mode->clock; + lane = 4; + link_bw = 270000; + } + igdng_compute_m_n(3, lane, target_clock, + link_bw, &m_n); } if (IS_IGD(dev)) @@ -2382,29 +2494,15 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, dpll_reg = pch_dpll_reg; } - if (dpll & DPLL_VCO_ENABLE) { + if (is_edp) { + igdng_disable_pll_edp(crtc); + } else if ((dpll & DPLL_VCO_ENABLE)) { I915_WRITE(fp_reg, fp); I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE); I915_READ(dpll_reg); udelay(150); } - if (IS_IGDNG(dev)) { - /* enable PCH clock reference source */ - /* XXX need to change the setting for other outputs */ - u32 temp; - temp = I915_READ(PCH_DREF_CONTROL); - temp &= ~DREF_NONSPREAD_SOURCE_MASK; - temp |= DREF_NONSPREAD_CK505_ENABLE; - temp &= ~DREF_SSC_SOURCE_MASK; - temp |= DREF_SSC_SOURCE_ENABLE; - temp &= ~DREF_SSC1_ENABLE; - /* if no eDP, disable source output to CPU */ - temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK; - temp |= DREF_CPU_SOURCE_OUTPUT_DISABLE; - I915_WRITE(PCH_DREF_CONTROL, temp); - } - /* The LVDS pin pair needs to be on before the DPLLs are enabled. * This is an exception to the general rule that mode_set doesn't turn * things on. @@ -2436,23 +2534,25 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, if (is_dp) intel_dp_set_m_n(crtc, mode, adjusted_mode); - I915_WRITE(fp_reg, fp); - I915_WRITE(dpll_reg, dpll); - I915_READ(dpll_reg); - /* Wait for the clocks to stabilize. */ - udelay(150); - - if (IS_I965G(dev) && !IS_IGDNG(dev)) { - sdvo_pixel_multiply = adjusted_mode->clock / mode->clock; - I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) | - ((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT)); - } else { - /* write it again -- the BIOS does, after all */ + if (!is_edp) { + I915_WRITE(fp_reg, fp); I915_WRITE(dpll_reg, dpll); + I915_READ(dpll_reg); + /* Wait for the clocks to stabilize. */ + udelay(150); + + if (IS_I965G(dev) && !IS_IGDNG(dev)) { + sdvo_pixel_multiply = adjusted_mode->clock / mode->clock; + I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) | + ((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT)); + } else { + /* write it again -- the BIOS does, after all */ + I915_WRITE(dpll_reg, dpll); + } + I915_READ(dpll_reg); + /* Wait for the clocks to stabilize. */ + udelay(150); } - I915_READ(dpll_reg); - /* Wait for the clocks to stabilize. */ - udelay(150); I915_WRITE(htot_reg, (adjusted_mode->crtc_hdisplay - 1) | ((adjusted_mode->crtc_htotal - 1) << 16)); @@ -2482,10 +2582,14 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc, I915_WRITE(link_m1_reg, m_n.link_m); I915_WRITE(link_n1_reg, m_n.link_n); - /* enable FDI RX PLL too */ - temp = I915_READ(fdi_rx_reg); - I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE); - udelay(200); + if (is_edp) { + igdng_set_pll_edp(crtc, adjusted_mode->clock); + } else { + /* enable FDI RX PLL too */ + temp = I915_READ(fdi_rx_reg); + I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE); + udelay(200); + } } I915_WRITE(pipeconf_reg, pipeconf); @@ -3083,6 +3187,9 @@ static void intel_setup_outputs(struct drm_device *dev) if (IS_IGDNG(dev)) { int found; + if (IS_MOBILE(dev) && (I915_READ(DP_A) & DP_DETECTED)) + intel_dp_init(dev, DP_A); + if (I915_READ(HDMIB) & PORT_DETECTED) { /* check SDVOB */ /* found = intel_sdvo_init(dev, HDMIB); */ @@ -3179,6 +3286,10 @@ static void intel_setup_outputs(struct drm_device *dev) (1 << 1)); clone_mask = (1 << INTEL_OUTPUT_DISPLAYPORT); break; + case INTEL_OUTPUT_EDP: + crtc_mask = (1 << 1); + clone_mask = (1 << INTEL_OUTPUT_EDP); + break; } encoder->possible_crtcs = crtc_mask; encoder->possible_clones = intel_connector_clones(dev, clone_mask); diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 0715911cbd84..a6ff15ac548a 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -40,6 +40,8 @@ #define DP_LINK_CONFIGURATION_SIZE 9 +#define IS_eDP(i) ((i)->type == INTEL_OUTPUT_EDP) + struct intel_dp_priv { uint32_t output_reg; uint32_t DP; @@ -63,6 +65,19 @@ intel_dp_link_train(struct intel_output *intel_output, uint32_t DP, static void intel_dp_link_down(struct intel_output *intel_output, uint32_t DP); +void +intel_edp_link_config (struct intel_output *intel_output, + int *lane_num, int *link_bw) +{ + struct intel_dp_priv *dp_priv = intel_output->dev_priv; + + *lane_num = dp_priv->lane_count; + if (dp_priv->link_bw == DP_LINK_BW_1_62) + *link_bw = 162000; + else if (dp_priv->link_bw == DP_LINK_BW_2_7) + *link_bw = 270000; +} + static int intel_dp_max_lane_count(struct intel_output *intel_output) { @@ -206,9 +221,10 @@ intel_dp_aux_ch(struct intel_output *intel_output, * and would like to run at 2MHz. So, take the * hrawclk value and divide by 2 and use that */ - /* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */ - if (IS_IGDNG(dev)) - aux_clock_divider = 62; + if (IS_eDP(intel_output)) + aux_clock_divider = 225; /* eDP input clock at 450Mhz */ + else if (IS_IGDNG(dev)) + aux_clock_divider = 62; /* IGDNG: input clock fixed at 125Mhz */ else aux_clock_divider = intel_hrawclk(dev) / 2; @@ -579,8 +595,38 @@ intel_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode, if (intel_crtc->pipe == 1) dp_priv->DP |= DP_PIPEB_SELECT; + + if (IS_eDP(intel_output)) { + /* don't miss out required setting for eDP */ + dp_priv->DP |= DP_PLL_ENABLE; + if (adjusted_mode->clock < 200000) + dp_priv->DP |= DP_PLL_FREQ_160MHZ; + else + dp_priv->DP |= DP_PLL_FREQ_270MHZ; + } } +static void igdng_edp_backlight_on (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 pp; + + DRM_DEBUG("\n"); + pp = I915_READ(PCH_PP_CONTROL); + pp |= EDP_BLC_ENABLE; + I915_WRITE(PCH_PP_CONTROL, pp); +} + +static void igdng_edp_backlight_off (struct drm_device *dev) +{ + struct drm_i915_private *dev_priv = dev->dev_private; + u32 pp; + + DRM_DEBUG("\n"); + pp = I915_READ(PCH_PP_CONTROL); + pp &= ~EDP_BLC_ENABLE; + I915_WRITE(PCH_PP_CONTROL, pp); +} static void intel_dp_dpms(struct drm_encoder *encoder, int mode) @@ -592,11 +638,17 @@ intel_dp_dpms(struct drm_encoder *encoder, int mode) uint32_t dp_reg = I915_READ(dp_priv->output_reg); if (mode != DRM_MODE_DPMS_ON) { - if (dp_reg & DP_PORT_EN) + if (dp_reg & DP_PORT_EN) { intel_dp_link_down(intel_output, dp_priv->DP); + if (IS_eDP(intel_output)) + igdng_edp_backlight_off(dev); + } } else { - if (!(dp_reg & DP_PORT_EN)) + if (!(dp_reg & DP_PORT_EN)) { intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration); + if (IS_eDP(intel_output)) + igdng_edp_backlight_on(dev); + } } dp_priv->dpms_mode = mode; } @@ -958,12 +1010,23 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP) struct drm_i915_private *dev_priv = dev->dev_private; struct intel_dp_priv *dp_priv = intel_output->dev_priv; + DRM_DEBUG("\n"); + + if (IS_eDP(intel_output)) { + DP &= ~DP_PLL_ENABLE; + I915_WRITE(dp_priv->output_reg, DP); + POSTING_READ(dp_priv->output_reg); + udelay(100); + } + DP &= ~DP_LINK_TRAIN_MASK; I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE); POSTING_READ(dp_priv->output_reg); udelay(17000); + if (IS_eDP(intel_output)) + DP |= DP_LINK_TRAIN_OFF; I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN); POSTING_READ(dp_priv->output_reg); } @@ -1089,11 +1152,27 @@ intel_dp_detect(struct drm_connector *connector) static int intel_dp_get_modes(struct drm_connector *connector) { struct intel_output *intel_output = to_intel_output(connector); + struct drm_device *dev = intel_output->base.dev; + struct drm_i915_private *dev_priv = dev->dev_private; + int ret; /* We should parse the EDID data and find out if it has an audio sink */ - return intel_ddc_get_modes(intel_output); + ret = intel_ddc_get_modes(intel_output); + if (ret) + return ret; + + /* if eDP has no EDID, try to use fixed panel mode from VBT */ + if (IS_eDP(intel_output)) { + if (dev_priv->panel_fixed_mode != NULL) { + struct drm_display_mode *mode; + mode = drm_mode_duplicate(dev, dev_priv->panel_fixed_mode); + drm_mode_probed_add(connector, mode); + return 1; + } + } + return 0; } static void @@ -1170,7 +1249,10 @@ intel_dp_init(struct drm_device *dev, int output_reg) DRM_MODE_CONNECTOR_DisplayPort); drm_connector_helper_add(connector, &intel_dp_connector_helper_funcs); - intel_output->type = INTEL_OUTPUT_DISPLAYPORT; + if (output_reg == DP_A) + intel_output->type = INTEL_OUTPUT_EDP; + else + intel_output->type = INTEL_OUTPUT_DISPLAYPORT; connector->interlace_allowed = true; connector->doublescan_allowed = 0; @@ -1191,6 +1273,9 @@ intel_dp_init(struct drm_device *dev, int output_reg) /* Set up the DDC bus. */ switch (output_reg) { + case DP_A: + name = "DPDDC-A"; + break; case DP_B: case PCH_DP_B: name = "DPDDC-B"; @@ -1206,9 +1291,22 @@ intel_dp_init(struct drm_device *dev, int output_reg) } intel_dp_i2c_init(intel_output, name); + intel_output->ddc_bus = &dp_priv->adapter; intel_output->hot_plug = intel_dp_hot_plug; + if (output_reg == DP_A) { + /* initialize panel mode from VBT if available for eDP */ + if (dev_priv->lfp_lvds_vbt_mode) { + dev_priv->panel_fixed_mode = + drm_mode_duplicate(dev, dev_priv->lfp_lvds_vbt_mode); + if (dev_priv->panel_fixed_mode) { + dev_priv->panel_fixed_mode->type |= + DRM_MODE_TYPE_PREFERRED; + } + } + } + /* For G4X desktop chip, PEG_BAND_GAP_DATA 3:0 must first be written * 0xd. Failure to do so will result in spurious interrupts being * generated on the port when a cable is not attached. diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h index 004541c935a8..d6f92ea1b553 100644 --- a/drivers/gpu/drm/i915/intel_drv.h +++ b/drivers/gpu/drm/i915/intel_drv.h @@ -55,6 +55,7 @@ #define INTEL_OUTPUT_TVOUT 5 #define INTEL_OUTPUT_HDMI 6 #define INTEL_OUTPUT_DISPLAYPORT 7 +#define INTEL_OUTPUT_EDP 8 #define INTEL_DVO_CHIP_NONE 0 #define INTEL_DVO_CHIP_LVDS 1 @@ -121,6 +122,8 @@ extern void intel_dp_init(struct drm_device *dev, int dp_reg); void intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode, struct drm_display_mode *adjusted_mode); +extern void intel_edp_link_config (struct intel_output *, int *, int *); + extern void intel_crtc_load_lut(struct drm_crtc *crtc); extern void intel_encoder_prepare (struct drm_encoder *encoder); diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c index 43c7d9aa59ce..3f445a80c552 100644 --- a/drivers/gpu/drm/i915/intel_lvds.c +++ b/drivers/gpu/drm/i915/intel_lvds.c @@ -892,6 +892,10 @@ void intel_lvds_init(struct drm_device *dev) if (IS_IGDNG(dev)) { if ((I915_READ(PCH_LVDS) & LVDS_DETECTED) == 0) return; + if (dev_priv->edp_support) { + DRM_DEBUG("disable LVDS for eDP support\n"); + return; + } gpio = PCH_GPIOC; } -- cgit v1.2.3 From 67941da28d59cca6817d35823fcb1e3e4eed030e Mon Sep 17 00:00:00 2001 From: Zhenyu Wang Date: Fri, 24 Jul 2009 01:00:33 +0800 Subject: drm/i915: fix VGA detect on IGDNG Check FORCE_DETECT bit to be clear for the finish of hotplug detect process. Also check possible mono monitor which should also be marked as connected. Signed-off-by: Zhenyu Wang Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_crt.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c index d6a1a6e5539a..4cf8e2e88a40 100644 --- a/drivers/gpu/drm/i915/intel_crt.c +++ b/drivers/gpu/drm/i915/intel_crt.c @@ -156,6 +156,9 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector) temp = adpa = I915_READ(PCH_ADPA); + adpa &= ~ADPA_DAC_ENABLE; + I915_WRITE(PCH_ADPA, adpa); + adpa &= ~ADPA_CRT_HOTPLUG_MASK; adpa |= (ADPA_CRT_HOTPLUG_PERIOD_128 | @@ -169,13 +172,14 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector) DRM_DEBUG("pch crt adpa 0x%x", adpa); I915_WRITE(PCH_ADPA, adpa); - /* This might not be needed as not specified in spec...*/ - udelay(1000); + while ((I915_READ(PCH_ADPA) & ADPA_CRT_HOTPLUG_FORCE_TRIGGER) != 0) + ; /* Check the status to see if both blue and green are on now */ adpa = I915_READ(PCH_ADPA); - if ((adpa & ADPA_CRT_HOTPLUG_MONITOR_MASK) == - ADPA_CRT_HOTPLUG_MONITOR_COLOR) + adpa &= ADPA_CRT_HOTPLUG_MONITOR_MASK; + if ((adpa == ADPA_CRT_HOTPLUG_MONITOR_COLOR) || + (adpa == ADPA_CRT_HOTPLUG_MONITOR_MONO)) ret = true; else ret = false; -- cgit v1.2.3 From f360132626b11d0dc60814033873ca0e3111677c Mon Sep 17 00:00:00 2001 From: Jesse Barnes Date: Wed, 22 Jul 2009 12:54:59 -0700 Subject: drm/i915: fix 845G FIFO size & burst length I had one report of flicker due to FIFO underruns on 845G. Scott was kind enough to test a few patches and report success with this one. Looks like 845G measures FIFO size slightly differently than other chips, and we were also clobbering the FIFO burst length. Fixing both of those issues gives him a healthy machine again. Note that we still only adjust plane A's watermark in the 830/845 case. If someone is willing to test we could support a bigger variety of dual-head 830/845 configurations with a bit more code. Fixes fdo bug #19304 (again). Reported-by: Scott Hansen Tested-by: Scott Hansen Signed-off-by: Jesse Barnes Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index a9f1307d32d8..1da7b0b9ed31 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -2026,6 +2026,9 @@ static int intel_get_fifo_size(struct drm_device *dev, int plane) size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) - (dsparb & 0x1ff); size >>= 1; /* Convert to cachelines */ + } else if (IS_845G(dev)) { + size = dsparb & 0x7f; + size >>= 2; /* Convert to cachelines */ } else { size = dsparb & 0x7f; size >>= 1; /* Convert to cachelines */ @@ -2125,14 +2128,16 @@ static void i830_update_wm(struct drm_device *dev, int planea_clock, int pixel_size) { struct drm_i915_private *dev_priv = dev->dev_private; - uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK; + uint32_t fwater_lo = I915_READ(FW_BLC) & ~0xfff; int planea_wm; i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0); planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info, pixel_size, latency_ns); - fwater_lo = fwater_lo | planea_wm; + fwater_lo |= (3<<8) | planea_wm; + + DRM_DEBUG("Setting FIFO watermarks - A: %d\n", planea_wm); I915_WRITE(FW_BLC, fwater_lo); } -- cgit v1.2.3 From bcae2ca81c4a085e3e0e8941b7c64f9aeb6fc05c Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Mon, 20 Jul 2009 13:20:23 +0800 Subject: drm/i915: Set preferred mode for integrated TV according to TV format In order to get best possible quality image we chose 640x480 for NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p TV format respectively. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_tv.c | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_tv.c b/drivers/gpu/drm/i915/intel_tv.c index a43c98e3f077..da4ab4dc1630 100644 --- a/drivers/gpu/drm/i915/intel_tv.c +++ b/drivers/gpu/drm/i915/intel_tv.c @@ -1490,6 +1490,27 @@ static struct input_res { {"1920x1080", 1920, 1080}, }; +/* + * Chose preferred mode according to line number of TV format + */ +static void +intel_tv_chose_preferred_modes(struct drm_connector *connector, + struct drm_display_mode *mode_ptr) +{ + struct intel_output *intel_output = to_intel_output(connector); + const struct tv_mode *tv_mode = intel_tv_mode_find(intel_output); + + if (tv_mode->nbr_end < 480 && mode_ptr->vdisplay == 480) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + else if (tv_mode->nbr_end > 480) { + if (tv_mode->progressive == true && tv_mode->nbr_end < 720) { + if (mode_ptr->vdisplay == 720) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + } else if (mode_ptr->vdisplay == 1080) + mode_ptr->type |= DRM_MODE_TYPE_PREFERRED; + } +} + /** * Stub get_modes function. * @@ -1544,6 +1565,7 @@ intel_tv_get_modes(struct drm_connector *connector) mode_ptr->clock = (int) tmp; mode_ptr->type = DRM_MODE_TYPE_DRIVER; + intel_tv_chose_preferred_modes(connector, mode_ptr); drm_mode_probed_add(connector, mode_ptr); count++; } -- cgit v1.2.3 From fb7a46f3cc7d7dcf7c5edb3a38c84e3f730d7adb Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Thu, 23 Jul 2009 17:11:34 +0800 Subject: drm/i915: Choose real sdvo output according to result from detection Baed on Eric's idea in order to handle multiple sdvo encoders we implement another approach to dynamically chose real one encoder after detection, which is contrasted with patch - drm/i915:Construct all possible sdvo outputs for sdvo encoder. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_sdvo.c | 231 +++++++++++++++++++++++++------------- 1 file changed, 153 insertions(+), 78 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c index 4f0c30948bc4..b68746f0380e 100644 --- a/drivers/gpu/drm/i915/intel_sdvo.c +++ b/drivers/gpu/drm/i915/intel_sdvo.c @@ -55,6 +55,12 @@ struct intel_sdvo_priv { /* Pixel clock limitations reported by the SDVO device, in kHz */ int pixel_clock_min, pixel_clock_max; + /* + * For multiple function SDVO device, + * this is for current attached outputs. + */ + uint16_t attached_output; + /** * This is set if we're going to treat the device as TV-out. * @@ -114,6 +120,9 @@ struct intel_sdvo_priv { u32 save_SDVOX; }; +static bool +intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags); + /** * Writes the SDVOB or SDVOC with the given value, but always writes both * SDVOB and SDVOC to work around apparent hardware issues (according to @@ -1435,6 +1444,39 @@ void intel_sdvo_set_hotplug(struct drm_connector *connector, int on) intel_sdvo_read_response(intel_output, &response, 2); } +static bool +intel_sdvo_multifunc_encoder(struct intel_output *intel_output) +{ + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + int caps = 0; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_RGB0 | SDVO_OUTPUT_RGB1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_SVID0 | SDVO_OUTPUT_SVID0)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_CVBS0 | SDVO_OUTPUT_CVBS1)) + caps++; + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_YPRPB0 | SDVO_OUTPUT_YPRPB1)) + caps++; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_SCART0 | SDVO_OUTPUT_SCART1)) + caps++; + + if (sdvo_priv->caps.output_flags & + (SDVO_OUTPUT_LVDS0 | SDVO_OUTPUT_LVDS1)) + caps++; + + return (caps > 1); +} + static void intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) { @@ -1453,23 +1495,31 @@ intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector) { - u8 response[2]; + uint16_t response; u8 status; struct intel_output *intel_output = to_intel_output(connector); + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; intel_sdvo_write_cmd(intel_output, SDVO_CMD_GET_ATTACHED_DISPLAYS, NULL, 0); status = intel_sdvo_read_response(intel_output, &response, 2); - DRM_DEBUG("SDVO response %d %d\n", response[0], response[1]); + DRM_DEBUG("SDVO response %d %d\n", response & 0xff, response >> 8); if (status != SDVO_CMD_STATUS_SUCCESS) return connector_status_unknown; - if ((response[0] != 0) || (response[1] != 0)) { - intel_sdvo_hdmi_sink_detect(connector); - return connector_status_connected; - } else + if (response == 0) return connector_status_disconnected; + + if (intel_sdvo_multifunc_encoder(intel_output) && + sdvo_priv->attached_output != response) { + if (sdvo_priv->controlled_output != response && + intel_sdvo_output_setup(intel_output, response) != true) + return connector_status_unknown; + sdvo_priv->attached_output = response; + } + intel_sdvo_hdmi_sink_detect(connector); + return connector_status_connected; } static void intel_sdvo_get_ddc_modes(struct drm_connector *connector) @@ -1866,16 +1916,101 @@ intel_sdvo_get_slave_addr(struct drm_device *dev, int output_device) return 0x72; } +static bool +intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags) +{ + struct drm_connector *connector = &intel_output->base; + struct drm_encoder *encoder = &intel_output->enc; + struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + bool ret = true, registered = false; + + sdvo_priv->is_tv = false; + intel_output->needs_tv_clock = false; + sdvo_priv->is_lvds = false; + + if (device_is_registered(&connector->kdev)) { + drm_sysfs_connector_remove(connector); + registered = true; + } + + if (flags & + (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { + if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0) + sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0; + else + sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1; + + encoder->encoder_type = DRM_MODE_ENCODER_TMDS; + connector->connector_type = DRM_MODE_CONNECTOR_DVID; + + if (intel_sdvo_get_supp_encode(intel_output, + &sdvo_priv->encode) && + intel_sdvo_get_digital_encoding_mode(intel_output) && + sdvo_priv->is_hdmi) { + /* enable hdmi encoding mode if supported */ + intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI); + intel_sdvo_set_colorimetry(intel_output, + SDVO_COLORIMETRY_RGB256); + connector->connector_type = DRM_MODE_CONNECTOR_HDMIA; + } + } else if (flags & SDVO_OUTPUT_SVID0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0; + encoder->encoder_type = DRM_MODE_ENCODER_TVDAC; + connector->connector_type = DRM_MODE_CONNECTOR_SVIDEO; + sdvo_priv->is_tv = true; + intel_output->needs_tv_clock = true; + } else if (flags & SDVO_OUTPUT_RGB0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0; + encoder->encoder_type = DRM_MODE_ENCODER_DAC; + connector->connector_type = DRM_MODE_CONNECTOR_VGA; + } else if (flags & SDVO_OUTPUT_RGB1) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1; + encoder->encoder_type = DRM_MODE_ENCODER_DAC; + connector->connector_type = DRM_MODE_CONNECTOR_VGA; + } else if (flags & SDVO_OUTPUT_LVDS0) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0; + encoder->encoder_type = DRM_MODE_ENCODER_LVDS; + connector->connector_type = DRM_MODE_CONNECTOR_LVDS; + sdvo_priv->is_lvds = true; + } else if (flags & SDVO_OUTPUT_LVDS1) { + + sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1; + encoder->encoder_type = DRM_MODE_ENCODER_LVDS; + connector->connector_type = DRM_MODE_CONNECTOR_LVDS; + sdvo_priv->is_lvds = true; + } else { + + unsigned char bytes[2]; + + sdvo_priv->controlled_output = 0; + memcpy(bytes, &sdvo_priv->caps.output_flags, 2); + DRM_DEBUG_KMS(I915_SDVO, + "%s: Unknown SDVO output type (0x%02x%02x)\n", + SDVO_NAME(sdvo_priv), + bytes[0], bytes[1]); + ret = false; + } + + if (ret && registered) + ret = drm_sysfs_connector_add(connector) == 0 ? true : false; + + + return ret; + +} + bool intel_sdvo_init(struct drm_device *dev, int output_device) { struct drm_connector *connector; struct intel_output *intel_output; struct intel_sdvo_priv *sdvo_priv; - int connector_type; u8 ch[0x40]; int i; - int encoder_type; intel_output = kcalloc(sizeof(struct intel_output)+sizeof(struct intel_sdvo_priv), 1, GFP_KERNEL); if (!intel_output) { @@ -1925,88 +2060,28 @@ bool intel_sdvo_init(struct drm_device *dev, int output_device) intel_output->ddc_bus->algo = &intel_sdvo_i2c_bit_algo; /* In defaut case sdvo lvds is false */ - sdvo_priv->is_lvds = false; intel_sdvo_get_capabilities(intel_output, &sdvo_priv->caps); - if (sdvo_priv->caps.output_flags & - (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { - if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0) - sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0; - else - sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1; - - encoder_type = DRM_MODE_ENCODER_TMDS; - connector_type = DRM_MODE_CONNECTOR_DVID; - - if (intel_sdvo_get_supp_encode(intel_output, - &sdvo_priv->encode) && - intel_sdvo_get_digital_encoding_mode(intel_output) && - sdvo_priv->is_hdmi) { - /* enable hdmi encoding mode if supported */ - intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI); - intel_sdvo_set_colorimetry(intel_output, - SDVO_COLORIMETRY_RGB256); - connector_type = DRM_MODE_CONNECTOR_HDMIA; - } - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_SVID0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0; - encoder_type = DRM_MODE_ENCODER_TVDAC; - connector_type = DRM_MODE_CONNECTOR_SVIDEO; - sdvo_priv->is_tv = true; - intel_output->needs_tv_clock = true; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0; - encoder_type = DRM_MODE_ENCODER_DAC; - connector_type = DRM_MODE_CONNECTOR_VGA; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB1) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1; - encoder_type = DRM_MODE_ENCODER_DAC; - connector_type = DRM_MODE_CONNECTOR_VGA; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS0) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0; - encoder_type = DRM_MODE_ENCODER_LVDS; - connector_type = DRM_MODE_CONNECTOR_LVDS; - sdvo_priv->is_lvds = true; - } - else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS1) - { - sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1; - encoder_type = DRM_MODE_ENCODER_LVDS; - connector_type = DRM_MODE_CONNECTOR_LVDS; - sdvo_priv->is_lvds = true; - } - else - { - unsigned char bytes[2]; - - sdvo_priv->controlled_output = 0; - memcpy (bytes, &sdvo_priv->caps.output_flags, 2); - DRM_DEBUG_KMS(I915_SDVO, - "%s: Unknown SDVO output type (0x%02x%02x)\n", - SDVO_NAME(sdvo_priv), - bytes[0], bytes[1]); - encoder_type = DRM_MODE_ENCODER_NONE; - connector_type = DRM_MODE_CONNECTOR_Unknown; + if (intel_sdvo_output_setup(intel_output, + sdvo_priv->caps.output_flags) != true) { + DRM_DEBUG("SDVO output failed to setup on SDVO%c\n", + output_device == SDVOB ? 'B' : 'C'); goto err_i2c; } + connector = &intel_output->base; drm_connector_init(dev, connector, &intel_sdvo_connector_funcs, - connector_type); + connector->connector_type); + drm_connector_helper_add(connector, &intel_sdvo_connector_helper_funcs); connector->interlace_allowed = 0; connector->doublescan_allowed = 0; connector->display_info.subpixel_order = SubPixelHorizontalRGB; - drm_encoder_init(dev, &intel_output->enc, &intel_sdvo_enc_funcs, encoder_type); + drm_encoder_init(dev, &intel_output->enc, + &intel_sdvo_enc_funcs, intel_output->enc.encoder_type); + drm_encoder_helper_add(&intel_output->enc, &intel_sdvo_helper_funcs); drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc); -- cgit v1.2.3 From 0e014e92ba93d905bcb39881dce2d38807b90c34 Mon Sep 17 00:00:00 2001 From: Peter Korsgaard Date: Fri, 17 Jul 2009 22:33:37 +0200 Subject: i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC value s3c24xx_i2c_init() was overwriting the IICLC value set just above in s3c24xx_i2c_clockrate() with zero, effectively disabling the platform line control setting. Signed-off-by: Peter Korsgaard Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-s3c2410.c | 5 ----- 1 file changed, 5 deletions(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 8f42a4536cdf..20bb0ceb027b 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -763,11 +763,6 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) dev_info(i2c->dev, "bus frequency set to %d KHz\n", freq); dev_dbg(i2c->dev, "S3C2410_IICCON=0x%02lx\n", iicon); - /* check for s3c2440 i2c controller */ - - if (s3c24xx_i2c_is2440(i2c)) - writel(0x0, i2c->regs + S3C2440_IICLC); - return 0; } -- cgit v1.2.3 From 783fd6fa4c144e3f6913e6fed89de10a6dd715a5 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 17 Jul 2009 15:24:00 +0200 Subject: i2c: strncpy does not null terminate string strlcpy() will always null terminate the string. Signed-off-by: Roel Kluin Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index fdd83277c8a8..f2b82ee39adf 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -879,7 +879,7 @@ omap_i2c_probe(struct platform_device *pdev) i2c_set_adapdata(adap, dev); adap->owner = THIS_MODULE; adap->class = I2C_CLASS_HWMON; - strncpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); + strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); adap->algo = &omap_i2c_algo; adap->dev.parent = &pdev->dev; -- cgit v1.2.3 From ccb3bc16b4891a82649d4bccbeefe60b1d9a62e2 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Wed, 22 Jul 2009 23:58:39 +0900 Subject: i2c-sh_mobile: change module_init() to subsys_initcall() Convert the i2c-sh_mobile i2c bus driver to use subsys_initcall() instead of module_init(). This change makes the driver register a bit earlier which together with earlier platform data moves the time for probe(). The earlier probe() makes it possible to use i2c_get_adapter() and i2c_transfer() from device_initcall(). The same strategy is used by other i2c bus drivers such as i2c-pxa.c and i2c-s3c2410.c. Signed-off-by: Magnus Damm [ben-linux@fluff.org: minor subject updaye] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-sh_mobile.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 4f3d99cd1692..820487d0d5c7 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -637,7 +637,7 @@ static void __exit sh_mobile_i2c_adap_exit(void) platform_driver_unregister(&sh_mobile_i2c_driver); } -module_init(sh_mobile_i2c_adap_init); +subsys_initcall(sh_mobile_i2c_adap_init); module_exit(sh_mobile_i2c_adap_exit); MODULE_DESCRIPTION("SuperH Mobile I2C Bus Controller driver"); -- cgit v1.2.3 From bfb6b6588af5ff762222cee79152d2be738ccc06 Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:14:06 -0500 Subject: i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT register Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt. On Interrupt: I2C_STAT[RDR], read 'RXSTAT' from I2C_BUFFSTAT[8-13] On Interrupt: I2C_STAT[XDR] read 'TXSTAT' from I2C_BUFFSTAT[0-5] Signed-off-by: Jagadeesh Pakaravoor Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index f2b82ee39adf..a69665788513 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -692,9 +692,10 @@ omap_i2c_isr(int this_irq, void *dev_id) if (dev->fifo_size) { if (stat & OMAP_I2C_STAT_RRDY) num_bytes = dev->fifo_size; - else - num_bytes = omap_i2c_read_reg(dev, - OMAP_I2C_BUFSTAT_REG); + else /* read RXSTAT on RDR interrupt */ + num_bytes = (omap_i2c_read_reg(dev, + OMAP_I2C_BUFSTAT_REG) + >> 8) & 0x3F; } while (num_bytes) { num_bytes--; @@ -731,9 +732,10 @@ omap_i2c_isr(int this_irq, void *dev_id) if (dev->fifo_size) { if (stat & OMAP_I2C_STAT_XRDY) num_bytes = dev->fifo_size; - else + else /* read TXSTAT on XDR interrupt */ num_bytes = omap_i2c_read_reg(dev, - OMAP_I2C_BUFSTAT_REG); + OMAP_I2C_BUFSTAT_REG) + & 0x3F; } while (num_bytes) { num_bytes--; -- cgit v1.2.3 From 04c688dd7a65935568b44629bfaa122eddf76e94 Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:14:40 -0500 Subject: i2c-omap: In case of a NACK|ARDY|AL return from the ISR In case of a NACK or ARDY or AL interrupt, complete the request. There is no need to service the RRDY/RDR or XRDY/XDR interrupts. Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method, in F/S and HS Modes http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index a69665788513..5c508ccf4384 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -685,8 +685,10 @@ omap_i2c_isr(int this_irq, void *dev_id) err |= OMAP_I2C_STAT_AL; } if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | - OMAP_I2C_STAT_AL)) + OMAP_I2C_STAT_AL)) { omap_i2c_complete_cmd(dev, err); + return IRQ_HANDLED; + } if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) { u8 num_bytes = 1; if (dev->fifo_size) { -- cgit v1.2.3 From cd086d3aa6f7f7bf4d4e1f9fa09af0f0b6bb99ec Mon Sep 17 00:00:00 2001 From: "Sonasath, Moiz" Date: Tue, 21 Jul 2009 10:15:12 -0500 Subject: i2c-omap: OMAP3430 Silicon Errata 1.153 When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG. Otherwise some data bytes can be lost while transferring them from the memory to the I2C interface. Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting if there is NACK | AL, set the appropriate error flags, ack the pending interrupts and return from the ISR. Signed-off-by: Moiz Sonasath Signed-off-by: Vikram pandita [ben-linux@fluff.org: fixed mail format and added i2c-omap to subject] Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-omap.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 5c508ccf4384..d258b02aef44 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -672,9 +672,10 @@ omap_i2c_isr(int this_irq, void *dev_id) break; } + err = 0; +complete: omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat); - err = 0; if (stat & OMAP_I2C_STAT_NACK) { err |= OMAP_I2C_STAT_NACK; omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, @@ -764,6 +765,27 @@ omap_i2c_isr(int this_irq, void *dev_id) "data to send\n"); break; } + + /* + * OMAP3430 Errata 1.153: When an XRDY/XDR + * is hit, wait for XUDF before writing data + * to DATA_REG. Otherwise some data bytes can + * be lost while transferring them from the + * memory to the I2C interface. + */ + + if (cpu_is_omap34xx()) { + while (!(stat & OMAP_I2C_STAT_XUDF)) { + if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { + omap_i2c_ack_stat(dev, stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR)); + err |= OMAP_I2C_STAT_XUDF; + goto complete; + } + cpu_relax(); + stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG); + } + } + omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w); } omap_i2c_ack_stat(dev, -- cgit v1.2.3 From 3d768213a6c34a27fac1804143da8cf18b8b175f Mon Sep 17 00:00:00 2001 From: Lu Zhihe Date: Wed, 29 Jul 2009 15:02:09 -0700 Subject: edac: x38 fix mchbar high register addr Intel X38 MCHBAR is a 64bits register, base from 0x48, so its higher base is 0x4C. Signed-off-by: Lu Zhihe Signed-off-by: Doug Thompson Cc: [2.6.30.x] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/edac/x38_edac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/edac/x38_edac.c b/drivers/edac/x38_edac.c index 2406c2ce2844..d4ec60593176 100644 --- a/drivers/edac/x38_edac.c +++ b/drivers/edac/x38_edac.c @@ -30,7 +30,7 @@ /* Intel X38 register addresses - device 0 function 0 - DRAM Controller */ #define X38_MCHBAR_LOW 0x48 /* MCH Memory Mapped Register BAR */ -#define X38_MCHBAR_HIGH 0x4b +#define X38_MCHBAR_HIGH 0x4c #define X38_MCHBAR_MASK 0xfffffc000ULL /* bits 35:14 */ #define X38_MMR_WINDOW_SIZE 16384 -- cgit v1.2.3 From c42b110caeb128819104d057acdaa1ae564b7c8d Mon Sep 17 00:00:00 2001 From: Pawel Osciak Date: Wed, 29 Jul 2009 15:02:10 -0700 Subject: s3c-fb: fix off-by-one bug in loop indexes Fixed off-by-one bug in loop indexes - some elements beyond windows' array were accessed, which might result in memory access violations when removing/suspending the device. Signed-off-by: Pawel Osciak Reviewed-by: Kyungmin Park Signed-off-by: Marek Szyprowski Cc: Krzysztof Helt Cc: Ben Dooks Cc: Russell King Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/s3c-fb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c index bb63c07e13de..5a72083dc67c 100644 --- a/drivers/video/s3c-fb.c +++ b/drivers/video/s3c-fb.c @@ -964,7 +964,7 @@ static int __devexit s3c_fb_remove(struct platform_device *pdev) struct s3c_fb *sfb = platform_get_drvdata(pdev); int win; - for (win = 0; win <= S3C_FB_MAX_WIN; win++) + for (win = 0; win < S3C_FB_MAX_WIN; win++) if (sfb->windows[win]) s3c_fb_release_win(sfb, sfb->windows[win]); @@ -988,7 +988,7 @@ static int s3c_fb_suspend(struct platform_device *pdev, pm_message_t state) struct s3c_fb_win *win; int win_no; - for (win_no = S3C_FB_MAX_WIN; win_no >= 0; win_no--) { + for (win_no = S3C_FB_MAX_WIN - 1; win_no >= 0; win_no--) { win = sfb->windows[win_no]; if (!win) continue; -- cgit v1.2.3 From ddb22195cb3dc5175ba3aac5e957d0e34cd2ee73 Mon Sep 17 00:00:00 2001 From: Jouni Hogander Date: Wed, 29 Jul 2009 15:02:11 -0700 Subject: spi: omap2_mcspi supports wake events Currently mcspi wake-ups are not enabled. This might cause cases where OMAP is not waking up on mcspi events. Signed-off-by: Jouni Hogander Signed-off-by: Tony Lindgren Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/omap2_mcspi.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index eee4b6e0af2c..2b64091b0f1f 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -59,6 +59,8 @@ /* per-register bitmasks: */ +#define OMAP2_MCSPI_SYSCONFIG_SMARTIDLE (2 << 3) +#define OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP (1 << 2) #define OMAP2_MCSPI_SYSCONFIG_AUTOIDLE (1 << 0) #define OMAP2_MCSPI_SYSCONFIG_SOFTRESET (1 << 1) @@ -90,6 +92,7 @@ #define OMAP2_MCSPI_CHCTRL_EN (1 << 0) +#define OMAP2_MCSPI_WAKEUPENABLE_WKEN (1 << 0) /* We have 2 DMA channels per CS, one for RX and one for TX */ struct omap2_mcspi_dma { @@ -873,8 +876,12 @@ static int __init omap2_mcspi_reset(struct omap2_mcspi *mcspi) } while (!(tmp & OMAP2_MCSPI_SYSSTATUS_RESETDONE)); mcspi_write_reg(master, OMAP2_MCSPI_SYSCONFIG, - /* (3 << 8) | (2 << 3) | */ - OMAP2_MCSPI_SYSCONFIG_AUTOIDLE); + OMAP2_MCSPI_SYSCONFIG_AUTOIDLE | + OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP | + OMAP2_MCSPI_SYSCONFIG_SMARTIDLE); + + mcspi_write_reg(master, OMAP2_MCSPI_WAKEUPENABLE, + OMAP2_MCSPI_WAKEUPENABLE_WKEN); omap2_mcspi_set_master_mode(master); -- cgit v1.2.3 From 57c5c28dbc835c67a9c23912bab56b7f165e7715 Mon Sep 17 00:00:00 2001 From: Eero Nurkkala Date: Wed, 29 Jul 2009 15:02:12 -0700 Subject: spi: omap2_mcspi rxdma bugfix When data is read through DMA, the last element must be read separately through the RX register. It cannot be transferred by the DMA. For further details see e.g. OMAP35x TRM (table 19-16). Without the fix the driver causes extra clocks to be clocked to the bus after DMA RX operations. This can cause interesting behaviour with some devices. Signed-off-by: Juuso Oikarinen Signed-off-by: Eero Nurkkala [aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.] Signed-off-by: Aaro Koskinen Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/omap2_mcspi.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index 2b64091b0f1f..9b80ad36dbba 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -272,7 +272,7 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer) if (rx != NULL) { omap_set_dma_transfer_params(mcspi_dma->dma_rx_channel, - data_type, element_count, 1, + data_type, element_count - 1, 1, OMAP_DMA_SYNC_ELEMENT, mcspi_dma->dma_rx_sync_dev, 1); @@ -303,6 +303,25 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer) if (rx != NULL) { wait_for_completion(&mcspi_dma->dma_rx_completion); dma_unmap_single(NULL, xfer->rx_dma, count, DMA_FROM_DEVICE); + omap2_mcspi_set_enable(spi, 0); + if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0) + & OMAP2_MCSPI_CHSTAT_RXS)) { + u32 w; + + w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0); + if (word_len <= 8) + ((u8 *)xfer->rx_buf)[element_count - 1] = w; + else if (word_len <= 16) + ((u16 *)xfer->rx_buf)[element_count - 1] = w; + else /* word_len <= 32 */ + ((u32 *)xfer->rx_buf)[element_count - 1] = w; + } else { + dev_err(&spi->dev, "DMA RX last word empty"); + count -= (word_len <= 8) ? 1 : + (word_len <= 16) ? 2 : + /* word_len <= 32 */ 4; + } + omap2_mcspi_set_enable(spi, 1); } return count; } -- cgit v1.2.3 From 659098141d02eb8e3545be8969d262e02d2f3f98 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Wed, 29 Jul 2009 15:02:13 -0700 Subject: rtc: mark if rtc-cmos drivers were successfully registered rtc-cmos has two drivers, one PNP and one platform. When PNP has not succeeded probing, platform is registered. However, it tries to unregister both drivers unconditionally, instead of only unregistering those that were successfully registered. This causes runtime warnings to be emitted from the driver core code. Fix this with a boolean variable for each driver indicating whether registering was successful. Signed-off-by: Thadeu Lima de Souza Cascardo Cc: David Brownell Cc: Bjorn Helgaas Cc: Alessandro Zummo Cc: Ingo Molnar Cc: David Brownell Cc: Kay Sievers Cc: Greg KH Cc: Ozan Caglayan Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/rtc/rtc-cmos.c | 23 ++++++++++++++++++----- 1 file changed, 18 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/rtc/rtc-cmos.c b/drivers/rtc/rtc-cmos.c index 23e10b6263d6..f7a4701bf863 100644 --- a/drivers/rtc/rtc-cmos.c +++ b/drivers/rtc/rtc-cmos.c @@ -1174,23 +1174,34 @@ static struct platform_driver cmos_platform_driver = { } }; +#ifdef CONFIG_PNP +static bool pnp_driver_registered; +#endif +static bool platform_driver_registered; + static int __init cmos_init(void) { int retval = 0; #ifdef CONFIG_PNP - pnp_register_driver(&cmos_pnp_driver); + retval = pnp_register_driver(&cmos_pnp_driver); + if (retval == 0) + pnp_driver_registered = true; #endif - if (!cmos_rtc.dev) + if (!cmos_rtc.dev) { retval = platform_driver_probe(&cmos_platform_driver, cmos_platform_probe); + if (retval == 0) + platform_driver_registered = true; + } if (retval == 0) return 0; #ifdef CONFIG_PNP - pnp_unregister_driver(&cmos_pnp_driver); + if (pnp_driver_registered) + pnp_unregister_driver(&cmos_pnp_driver); #endif return retval; } @@ -1199,9 +1210,11 @@ module_init(cmos_init); static void __exit cmos_exit(void) { #ifdef CONFIG_PNP - pnp_unregister_driver(&cmos_pnp_driver); + if (pnp_driver_registered) + pnp_unregister_driver(&cmos_pnp_driver); #endif - platform_driver_unregister(&cmos_platform_driver); + if (platform_driver_registered) + platform_driver_unregister(&cmos_platform_driver); } module_exit(cmos_exit); -- cgit v1.2.3 From b317c833211b7fbf902163de766f09554090e0bf Mon Sep 17 00:00:00 2001 From: Kristoffer Ericson Date: Wed, 29 Jul 2009 15:04:03 -0700 Subject: drivers/video/backlight/jornada720_bl.c: fix build Signed-off-by: Kristoffer Ericson Cc: Richard Purdie Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/backlight/jornada720_bl.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/video/backlight/jornada720_bl.c b/drivers/video/backlight/jornada720_bl.c index c3ebb6b41ce1..7aed2565c1bd 100644 --- a/drivers/video/backlight/jornada720_bl.c +++ b/drivers/video/backlight/jornada720_bl.c @@ -72,7 +72,7 @@ static int jornada_bl_update_status(struct backlight_device *bd) if (jornada_ssp_byte(SETBRIGHTNESS) != TXDUMMY) { printk(KERN_INFO "bl : failed to set brightness\n"); ret = -ETIMEDOUT; - goto out + goto out; } /* at this point we expect that the mcu has accepted -- cgit v1.2.3 From f0d83679a8d471dc8b646919f70595d6fe8c9606 Mon Sep 17 00:00:00 2001 From: Sebastian Heutling Date: Wed, 29 Jul 2009 15:04:05 -0700 Subject: eeprom/at25: bugfix "not ready" timeout after write Under certain circumstances msleep(1) within the loop, which waits for the EEPROM to be finished, might take longer than the timeout. On the next loop the status register might now return to be ready and therefore the loop finishes. The following check now tests if a timeout occurred and if so returns an error although the device reported it was ready. This fix replaces testing the occurrence of the timeout by testing the "not ready" bit in the status register. Signed-off-by: Sebastian Heutling Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/misc/eeprom/at25.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c index b34cb5f79eea..2e535a0ccd5e 100644 --- a/drivers/misc/eeprom/at25.c +++ b/drivers/misc/eeprom/at25.c @@ -173,6 +173,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, unsigned segment; unsigned offset = (unsigned) off; u8 *cp = bounce + 1; + int sr; *cp = AT25_WREN; status = spi_write(at25->spi, cp, 1); @@ -214,7 +215,6 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT); retries = 0; do { - int sr; sr = spi_w8r8(at25->spi, AT25_RDSR); if (sr < 0 || (sr & AT25_SR_nRDY)) { @@ -228,7 +228,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off, break; } while (retries++ < 3 || time_before_eq(jiffies, timeout)); - if (time_after(jiffies, timeout)) { + if ((sr < 0) || (sr & AT25_SR_nRDY)) { dev_err(&at25->spi->dev, "write %d bytes offset %d, " "timeout after %u msecs\n", -- cgit v1.2.3 From cab8bd3410d448279e3bd0fbf96d31db0bf770fa Mon Sep 17 00:00:00 2001 From: Hidetoshi Seto Date: Wed, 29 Jul 2009 15:04:14 -0700 Subject: sysrq, kdump: make sysrq-c consistent commit d6580a9f15238b87e618310c862231ae3f352d2d ("kexec: sysrq: simplify sysrq-c handler") changed the behavior of sysrq-c to unconditional dereference of NULL pointer. So in cases with CONFIG_KEXEC, where crash_kexec() was directly called from sysrq-c before, now it can be said that a step of "real oops" was inserted before starting kdump. However, in contrast to oops via SysRq-c from keyboard which results in panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will not become panic unless panic_on_oops=1. It means that even if dump is properly configured to be taken on panic, the sysrq-c from proc interface might not start crashdump while the sysrq-c from keyboard can start crashdump. This confuses traditional users of kdump, i.e. people who expect sysrq-c to do common behavior in both of the keyboard and proc interface. This patch brings the keyboard and proc interface behavior of sysrq-c in line, by forcing panic_on_oops=1 before oops in sysrq-c handler. And some updates in documentation are included, to clarify that there is no longer dependency with CONFIG_KEXEC, and that now the system can just crash by sysrq-c if no dump mechanism is configured. Signed-off-by: Hidetoshi Seto Cc: Lai Jiangshan Cc: Ken'ichi Ohmichi Acked-by: Neil Horman Acked-by: Vivek Goyal Cc: Brayan Arraes Cc: Eric W. Biederman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/sysrq.txt | 7 ++++--- drivers/char/sysrq.c | 8 +++++--- 2 files changed, 9 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt index cf42b820ff9d..d56a01775423 100644 --- a/Documentation/sysrq.txt +++ b/Documentation/sysrq.txt @@ -66,7 +66,8 @@ On all - write a character to /proc/sysrq-trigger. e.g.: 'b' - Will immediately reboot the system without syncing or unmounting your disks. -'c' - Will perform a kexec reboot in order to take a crashdump. +'c' - Will perform a system crash by a NULL pointer dereference. + A crashdump will be taken if configured. 'd' - Shows all locks that are held. @@ -141,8 +142,8 @@ useful when you want to exit a program that will not let you switch consoles. re'B'oot is good when you're unable to shut down. But you should also 'S'ync and 'U'mount first. -'C'rashdump can be used to manually trigger a crashdump when the system is hung. -The kernel needs to have been built with CONFIG_KEXEC enabled. +'C'rash can be used to manually trigger a crashdump when the system is hung. +Note that this just triggers a crash if there is no dump mechanism available. 'S'ync is great when your system is locked up, it allows you to sync your disks and will certainly lessen the chance of data loss and fscking. Note diff --git a/drivers/char/sysrq.c b/drivers/char/sysrq.c index 0db35857e4d8..5d7a02f63e1c 100644 --- a/drivers/char/sysrq.c +++ b/drivers/char/sysrq.c @@ -35,7 +35,6 @@ #include #include #include -#include #include #include @@ -124,9 +123,12 @@ static struct sysrq_key_op sysrq_unraw_op = { static void sysrq_handle_crash(int key, struct tty_struct *tty) { char *killer = NULL; + + panic_on_oops = 1; /* force panic */ + wmb(); *killer = 1; } -static struct sysrq_key_op sysrq_crashdump_op = { +static struct sysrq_key_op sysrq_crash_op = { .handler = sysrq_handle_crash, .help_msg = "Crash", .action_msg = "Trigger a crash", @@ -401,7 +403,7 @@ static struct sysrq_key_op *sysrq_key_table[36] = { */ NULL, /* a */ &sysrq_reboot_op, /* b */ - &sysrq_crashdump_op, /* c & ibm_emac driver debug */ + &sysrq_crash_op, /* c & ibm_emac driver debug */ &sysrq_showlocks_op, /* d */ &sysrq_term_op, /* e */ &sysrq_moom_op, /* f */ -- cgit v1.2.3 From a9e58f25734e153b8c6516d904e2398fb8b0b23d Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 29 Jul 2009 15:04:16 -0700 Subject: sdhci: get rid of "frequency too high" flood when using eSDHC Since commit 8dfd0374be84793360db7fff2e635d2cd3bbcb21 ("MMC core: limit minimum initialization frequency to 400kHz") MMC core checks for minimum frequency, and that causes following messages flood when using eSDHC controllers: ... mmc0: Minimum clock frequency too high for identification mode mmc0: Minimum clock frequency too high for identification mode ... The warnings are legitimate, since if we'd use 133 MHz clocks for standard SDHCI controllers, we'd not able to scale frequency down to 400 kHz. But eSDHC controllers have a non-standard SD clock management, so we can divide clock by 256 * 16, not just 256. This patch introduces get_min_clock() callback for sdhci core and implements it for sdhci-of driver, and thus fixes the issue. Signed-off-by: Anton Vorontsov Cc: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Pierre Ossman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/mmc/host/sdhci-of.c | 8 ++++++++ drivers/mmc/host/sdhci.c | 5 ++++- drivers/mmc/host/sdhci.h | 1 + 3 files changed, 13 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c index d79fa55c3b89..908844327db0 100644 --- a/drivers/mmc/host/sdhci-of.c +++ b/drivers/mmc/host/sdhci-of.c @@ -158,6 +158,13 @@ static unsigned int esdhc_get_max_clock(struct sdhci_host *host) return of_host->clock; } +static unsigned int esdhc_get_min_clock(struct sdhci_host *host) +{ + struct sdhci_of_host *of_host = sdhci_priv(host); + + return of_host->clock / 256 / 16; +} + static unsigned int esdhc_get_timeout_clock(struct sdhci_host *host) { struct sdhci_of_host *of_host = sdhci_priv(host); @@ -184,6 +191,7 @@ static struct sdhci_of_data sdhci_esdhc = { .set_clock = esdhc_set_clock, .enable_dma = esdhc_enable_dma, .get_max_clock = esdhc_get_max_clock, + .get_min_clock = esdhc_get_min_clock, .get_timeout_clock = esdhc_get_timeout_clock, }, }; diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 6779b4ecab18..62041c7e9246 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -1766,7 +1766,10 @@ int sdhci_add_host(struct sdhci_host *host) * Set host parameters. */ mmc->ops = &sdhci_ops; - mmc->f_min = host->max_clk / 256; + if (host->ops->get_min_clock) + mmc->f_min = host->ops->get_min_clock(host); + else + mmc->f_min = host->max_clk / 256; mmc->f_max = host->max_clk; mmc->caps = MMC_CAP_SDIO_IRQ; diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 831ddf7dcb49..c77e9ff30223 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -302,6 +302,7 @@ struct sdhci_ops { int (*enable_dma)(struct sdhci_host *host); unsigned int (*get_max_clock)(struct sdhci_host *host); + unsigned int (*get_min_clock)(struct sdhci_host *host); unsigned int (*get_timeout_clock)(struct sdhci_host *host); }; -- cgit v1.2.3 From 8da14b5fc32368f582df09fe9c0bec2507868583 Mon Sep 17 00:00:00 2001 From: Albin Tonnerre Date: Wed, 29 Jul 2009 15:04:18 -0700 Subject: drivers/serial/atmel_serial.c: fix compile when CONFIG_SERIAL_ATMEL=Y and CONFIG_SERIAL_ATMEL_CONSOLE=N When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in atmel_serial_probe makes the compile fail. This fixes the issue by only accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined Signed-off-by: Albin Tonnerre Signed-off-by: Haavard Skinnemoen Cc: Nicolas Ferre Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/serial/atmel_serial.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c index 338b15c0a548..607d43a31048 100644 --- a/drivers/serial/atmel_serial.c +++ b/drivers/serial/atmel_serial.c @@ -1551,6 +1551,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev) if (ret) goto err_add_port; +#ifdef CONFIG_SERIAL_ATMEL_CONSOLE if (atmel_is_console_port(&port->uart) && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) { /* @@ -1559,6 +1560,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev) */ clk_disable(port->clk); } +#endif device_init_wakeup(&pdev->dev, 1); platform_set_drvdata(pdev, port); -- cgit v1.2.3 From 6e900de3fff01e84c96632409359a84825c54b28 Mon Sep 17 00:00:00 2001 From: Mark Ware Date: Mon, 20 Jul 2009 21:51:03 +1000 Subject: cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c This is another alloc_bootmem() -> kzalloc() change, this time to fix the non-fatal badness caused when booting with a cpm2_uart console. Signed-off-by: Mark Ware Signed-off-by: Kumar Gala --- drivers/serial/cpm_uart/cpm_uart_cpm2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c index 141c0a3333ad..a9802e76b5fa 100644 --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c @@ -132,7 +132,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con) memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) + L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize); if (is_con) { - mem_addr = alloc_bootmem(memsz); + mem_addr = kzalloc(memsz, GFP_NOWAIT); dma_addr = virt_to_bus(mem_addr); } else -- cgit v1.2.3 From f294526279cda8934b0313ebd02184a16ba888c9 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 19 Jul 2009 14:46:09 +0300 Subject: lguest: dereferencing freed mem in add_eventfd() "new" was freed and then dereferenced. Also the return value wasn't being used so I modified the caller as well. Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git). regards, dan carpenter Signed-off-by: Dan Carpenter Signed-off-by: Rusty Russell --- drivers/lguest/lguest_user.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 9f9a2953b383..407722a8e0c4 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -52,8 +52,9 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) new->map[new->num].addr = addr; new->map[new->num].event = eventfd_ctx_fdget(fd); if (IS_ERR(new->map[new->num].event)) { + int err = PTR_ERR(new->map[new->num].event); kfree(new); - return PTR_ERR(new->map[new->num].event); + return err; } new->num++; @@ -83,7 +84,7 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) err = add_eventfd(lg, addr, fd); mutex_unlock(&lguest_lock); - return 0; + return err; } /*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt -- cgit v1.2.3 From ff52c3fc7188855ede75d87b022271f0da309e5b Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Thu, 23 Jul 2009 14:57:37 +0300 Subject: virtio: fix memory leak on device removal Make vp_free_vectors do the reverse of vq_request_vectors. Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 28 +++++++++++++++------------- 1 file changed, 15 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index bcec78ffc765..ca40517ef9c2 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -258,7 +258,6 @@ static void vp_free_vectors(struct virtio_device *vdev) for (i = 0; i < vp_dev->msix_used_vectors; ++i) free_irq(vp_dev->msix_entries[i].vector, vp_dev); - vp_dev->msix_used_vectors = 0; if (vp_dev->msix_enabled) { /* Disable the vector used for configuration */ @@ -267,9 +266,16 @@ static void vp_free_vectors(struct virtio_device *vdev) /* Flush the write out to device */ ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - vp_dev->msix_enabled = 0; pci_disable_msix(vp_dev->pci_dev); + vp_dev->msix_enabled = 0; + vp_dev->msix_vectors = 0; } + + vp_dev->msix_used_vectors = 0; + kfree(vp_dev->msix_names); + vp_dev->msix_names = NULL; + kfree(vp_dev->msix_entries); + vp_dev->msix_entries = NULL; } static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries, @@ -297,11 +303,11 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries, GFP_KERNEL); if (!vp_dev->msix_entries) - goto error_entries; + goto error; vp_dev->msix_names = kmalloc(nvectors * sizeof *vp_dev->msix_names, GFP_KERNEL); if (!vp_dev->msix_names) - goto error_names; + goto error; for (i = 0; i < nvectors; ++i) vp_dev->msix_entries[i].entry = i; @@ -314,7 +320,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, IRQF_SHARED, name, vp_dev); if (err) - goto error_irq; + goto error; vp_dev->intx_enabled = 1; } else { vp_dev->msix_vectors = err; @@ -328,7 +334,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_config_changed, 0, vp_dev->msix_names[v], vp_dev); if (err) - goto error_irq; + goto error; ++vp_dev->msix_used_vectors; iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); @@ -336,7 +342,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); if (v == VIRTIO_MSI_NO_VECTOR) { err = -EBUSY; - goto error_irq; + goto error; } } @@ -349,16 +355,12 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) vp_vring_interrupt, 0, vp_dev->msix_names[v], vp_dev); if (err) - goto error_irq; + goto error; ++vp_dev->msix_used_vectors; } return 0; -error_irq: +error: vp_free_vectors(vdev); - kfree(vp_dev->msix_names); -error_names: - kfree(vp_dev->msix_entries); -error_entries: return err; } -- cgit v1.2.3 From f6c82507030d61e15928d5cad946d3eac1c4a384 Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Sun, 26 Jul 2009 15:48:01 +0300 Subject: virtio: delete vq from list This makes delete vq the reverse of find vq. This is required to make it possible to retry find_vqs after a failure, otherwise the list gets corrupted. Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index ca40517ef9c2..a1cb1a1c6522 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -464,7 +464,11 @@ static void vp_del_vq(struct virtqueue *vq) { struct virtio_pci_device *vp_dev = to_vp_device(vq->vdev); struct virtio_pci_vq_info *info = vq->priv; - unsigned long size; + unsigned long flags, size; + + spin_lock_irqsave(&vp_dev->lock, flags); + list_del(&info->node); + spin_unlock_irqrestore(&vp_dev->lock, flags); iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL); -- cgit v1.2.3 From e969fed542cae08cb11d666efac4f7c5d624d09f Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Sun, 26 Jul 2009 15:48:08 +0300 Subject: virtio: refactor find_vqs This refactors find_vqs, making it more readable and robust, and fixing two regressions from 2.6.30: - double free_irq causing BUG_ON on device removal - probe failure when vq can't be assigned to msi-x vector (reported on old host kernels) Tested-by: Amit Shah Signed-off-by: Michael S. Tsirkin Signed-off-by: Rusty Russell --- drivers/virtio/virtio_pci.c | 212 +++++++++++++++++++++++++------------------- 1 file changed, 119 insertions(+), 93 deletions(-) (limited to 'drivers') diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c index a1cb1a1c6522..248e00ec4dc1 100644 --- a/drivers/virtio/virtio_pci.c +++ b/drivers/virtio/virtio_pci.c @@ -52,8 +52,10 @@ struct virtio_pci_device char (*msix_names)[256]; /* Number of available vectors */ unsigned msix_vectors; - /* Vectors allocated */ + /* Vectors allocated, excluding per-vq vectors if any */ unsigned msix_used_vectors; + /* Whether we have vector per vq */ + bool per_vq_vectors; }; /* Constants for MSI-X */ @@ -278,27 +280,24 @@ static void vp_free_vectors(struct virtio_device *vdev) vp_dev->msix_entries = NULL; } -static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries, - int *options, int noptions) -{ - int i; - for (i = 0; i < noptions; ++i) - if (!pci_enable_msix(dev, entries, options[i])) - return options[i]; - return -EBUSY; -} - -static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) +static int vp_request_vectors(struct virtio_device *vdev, int nvectors, + bool per_vq_vectors) { struct virtio_pci_device *vp_dev = to_vp_device(vdev); const char *name = dev_name(&vp_dev->vdev.dev); unsigned i, v; int err = -ENOMEM; - /* We want at most one vector per queue and one for config changes. - * Fallback to separate vectors for config and a shared for queues. - * Finally fall back to regular interrupts. */ - int options[] = { max_vqs + 1, 2 }; - int nvectors = max(options[0], options[1]); + + if (!nvectors) { + /* Can't allocate MSI-X vectors, use regular interrupt */ + vp_dev->msix_vectors = 0; + err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, + IRQF_SHARED, name, vp_dev); + if (err) + return err; + vp_dev->intx_enabled = 1; + return 0; + } vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries, GFP_KERNEL); @@ -312,41 +311,34 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs) for (i = 0; i < nvectors; ++i) vp_dev->msix_entries[i].entry = i; - err = vp_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries, - options, ARRAY_SIZE(options)); - if (err < 0) { - /* Can't allocate enough MSI-X vectors, use regular interrupt */ - vp_dev->msix_vectors = 0; - err = request_irq(vp_dev->pci_dev->irq, vp_interrupt, - IRQF_SHARED, name, vp_dev); - if (err) - goto error; - vp_dev->intx_enabled = 1; - } else { - vp_dev->msix_vectors = err; - vp_dev->msix_enabled = 1; - - /* Set the vector used for configuration */ - v = vp_dev->msix_used_vectors; - snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, - "%s-config", name); - err = request_irq(vp_dev->msix_entries[v].vector, - vp_config_changed, 0, vp_dev->msix_names[v], - vp_dev); - if (err) - goto error; - ++vp_dev->msix_used_vectors; + err = pci_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries, nvectors); + if (err > 0) + err = -ENOSPC; + if (err) + goto error; + vp_dev->msix_vectors = nvectors; + vp_dev->msix_enabled = 1; + + /* Set the vector used for configuration */ + v = vp_dev->msix_used_vectors; + snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, + "%s-config", name); + err = request_irq(vp_dev->msix_entries[v].vector, + vp_config_changed, 0, vp_dev->msix_names[v], + vp_dev); + if (err) + goto error; + ++vp_dev->msix_used_vectors; - iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - /* Verify we had enough resources to assign the vector */ - v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); - if (v == VIRTIO_MSI_NO_VECTOR) { - err = -EBUSY; - goto error; - } + iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); + /* Verify we had enough resources to assign the vector */ + v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR); + if (v == VIRTIO_MSI_NO_VECTOR) { + err = -EBUSY; + goto error; } - if (vp_dev->msix_vectors && vp_dev->msix_vectors != max_vqs + 1) { + if (!per_vq_vectors) { /* Shared vector for all VQs */ v = vp_dev->msix_used_vectors; snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names, @@ -366,13 +358,14 @@ error: static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, void (*callback)(struct virtqueue *vq), - const char *name) + const char *name, + u16 vector) { struct virtio_pci_device *vp_dev = to_vp_device(vdev); struct virtio_pci_vq_info *info; struct virtqueue *vq; unsigned long flags, size; - u16 num, vector; + u16 num; int err; /* Select the queue we're interested in */ @@ -391,7 +384,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, info->queue_index = index; info->num = num; - info->vector = VIRTIO_MSI_NO_VECTOR; + info->vector = vector; size = PAGE_ALIGN(vring_size(num, VIRTIO_PCI_VRING_ALIGN)); info->queue = alloc_pages_exact(size, GFP_KERNEL|__GFP_ZERO); @@ -415,22 +408,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, vq->priv = info; info->vq = vq; - /* allocate per-vq vector if available and necessary */ - if (callback && vp_dev->msix_used_vectors < vp_dev->msix_vectors) { - vector = vp_dev->msix_used_vectors; - snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names, - "%s-%s", dev_name(&vp_dev->vdev.dev), name); - err = request_irq(vp_dev->msix_entries[vector].vector, - vring_interrupt, 0, - vp_dev->msix_names[vector], vq); - if (err) - goto out_request_irq; - info->vector = vector; - ++vp_dev->msix_used_vectors; - } else - vector = VP_MSIX_VQ_VECTOR; - - if (callback && vp_dev->msix_enabled) { + if (vector != VIRTIO_MSI_NO_VECTOR) { iowrite16(vector, vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); vector = ioread16(vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); if (vector == VIRTIO_MSI_NO_VECTOR) { @@ -446,11 +424,6 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index, return vq; out_assign: - if (info->vector != VIRTIO_MSI_NO_VECTOR) { - free_irq(vp_dev->msix_entries[info->vector].vector, vq); - --vp_dev->msix_used_vectors; - } -out_request_irq: vring_del_virtqueue(vq); out_activate_queue: iowrite32(0, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_PFN); @@ -472,9 +445,6 @@ static void vp_del_vq(struct virtqueue *vq) iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL); - if (info->vector != VIRTIO_MSI_NO_VECTOR) - free_irq(vp_dev->msix_entries[info->vector].vector, vq); - if (vp_dev->msix_enabled) { iowrite16(VIRTIO_MSI_NO_VECTOR, vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR); @@ -495,36 +465,62 @@ static void vp_del_vq(struct virtqueue *vq) /* the config->del_vqs() implementation */ static void vp_del_vqs(struct virtio_device *vdev) { + struct virtio_pci_device *vp_dev = to_vp_device(vdev); struct virtqueue *vq, *n; + struct virtio_pci_vq_info *info; - list_for_each_entry_safe(vq, n, &vdev->vqs, list) + list_for_each_entry_safe(vq, n, &vdev->vqs, list) { + info = vq->priv; + if (vp_dev->per_vq_vectors) + free_irq(vp_dev->msix_entries[info->vector].vector, vq); vp_del_vq(vq); + } + vp_dev->per_vq_vectors = false; vp_free_vectors(vdev); } -/* the config->find_vqs() implementation */ -static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs, - struct virtqueue *vqs[], - vq_callback_t *callbacks[], - const char *names[]) +static int vp_try_to_find_vqs(struct virtio_device *vdev, unsigned nvqs, + struct virtqueue *vqs[], + vq_callback_t *callbacks[], + const char *names[], + int nvectors, + bool per_vq_vectors) { - int vectors = 0; - int i, err; - - /* How many vectors would we like? */ - for (i = 0; i < nvqs; ++i) - if (callbacks[i]) - ++vectors; + struct virtio_pci_device *vp_dev = to_vp_device(vdev); + u16 vector; + int i, err, allocated_vectors; - err = vp_request_vectors(vdev, vectors); + err = vp_request_vectors(vdev, nvectors, per_vq_vectors); if (err) goto error_request; + vp_dev->per_vq_vectors = per_vq_vectors; + allocated_vectors = vp_dev->msix_used_vectors; for (i = 0; i < nvqs; ++i) { - vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i]); - if (IS_ERR(vqs[i])) + if (!callbacks[i] || !vp_dev->msix_enabled) + vector = VIRTIO_MSI_NO_VECTOR; + else if (vp_dev->per_vq_vectors) + vector = allocated_vectors++; + else + vector = VP_MSIX_VQ_VECTOR; + vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i], vector); + if (IS_ERR(vqs[i])) { + err = PTR_ERR(vqs[i]); goto error_find; + } + /* allocate per-vq irq if available and necessary */ + if (vp_dev->per_vq_vectors && vector != VIRTIO_MSI_NO_VECTOR) { + snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names, + "%s-%s", dev_name(&vp_dev->vdev.dev), names[i]); + err = request_irq(vp_dev->msix_entries[vector].vector, + vring_interrupt, 0, + vp_dev->msix_names[vector], vqs[i]); + if (err) { + vp_del_vq(vqs[i]); + goto error_find; + } + } } return 0; @@ -532,7 +528,37 @@ error_find: vp_del_vqs(vdev); error_request: - return PTR_ERR(vqs[i]); + return err; +} + +/* the config->find_vqs() implementation */ +static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs, + struct virtqueue *vqs[], + vq_callback_t *callbacks[], + const char *names[]) +{ + int vectors = 0; + int i, uninitialized_var(err); + + /* How many vectors would we like? */ + for (i = 0; i < nvqs; ++i) + if (callbacks[i]) + ++vectors; + + /* We want at most one vector per queue and one for config changes. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + vectors + 1, true); + if (!err) + return 0; + /* Fallback to separate vectors for config and a shared for queues. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + 2, false); + if (!err) + return 0; + /* Finally fall back to regular interrupts. */ + err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names, + 0, false); + return err; } static struct virtio_config_ops virtio_pci_config_ops = { -- cgit v1.2.3 From 2e04ef76916d1e29a077ea9d0f2003c8fd86724d Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:45 -0600 Subject: lguest: fix comment style I don't really notice it (except to begrudge the extra vertical space), but Ingo does. And he pointed out that one excuse of lguest is as a teaching tool, it should set a good example. Signed-off-by: Rusty Russell Cc: Ingo Molnar --- Documentation/lguest/lguest.c | 540 ++++++++++++++++++++++------------ arch/x86/include/asm/lguest.h | 3 +- arch/x86/include/asm/lguest_hcall.h | 10 +- arch/x86/lguest/boot.c | 428 +++++++++++++++++---------- arch/x86/lguest/i386_head.S | 110 ++++--- drivers/lguest/core.c | 114 ++++--- drivers/lguest/hypercalls.c | 141 ++++++--- drivers/lguest/interrupts_and_traps.c | 288 ++++++++++++------ drivers/lguest/lg.h | 23 +- drivers/lguest/lguest_device.c | 150 ++++++---- drivers/lguest/lguest_user.c | 137 ++++++--- drivers/lguest/page_tables.c | 427 ++++++++++++++++++--------- drivers/lguest/segments.c | 106 ++++--- drivers/lguest/x86/core.c | 372 +++++++++++++++-------- drivers/lguest/x86/switcher_32.S | 18 +- include/linux/lguest.h | 36 ++- include/linux/lguest_launcher.h | 18 +- 17 files changed, 1906 insertions(+), 1015 deletions(-) (limited to 'drivers') diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 45d7d6dcae7a..aa66a52b73e9 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -1,7 +1,9 @@ -/*P:100 This is the Launcher code, a simple program which lays out the - * "physical" memory for the new Guest by mapping the kernel image and - * the virtual devices, then opens /dev/lguest to tell the kernel - * about the Guest and control it. :*/ +/*P:100 + * This is the Launcher code, a simple program which lays out the "physical" + * memory for the new Guest by mapping the kernel image and the virtual + * devices, then opens /dev/lguest to tell the kernel about the Guest and + * control it. +:*/ #define _LARGEFILE64_SOURCE #define _GNU_SOURCE #include @@ -46,13 +48,15 @@ #include "linux/virtio_rng.h" #include "linux/virtio_ring.h" #include "asm/bootparam.h" -/*L:110 We can ignore the 39 include files we need for this program, but I do - * want to draw attention to the use of kernel-style types. +/*L:110 + * We can ignore the 39 include files we need for this program, but I do want + * to draw attention to the use of kernel-style types. * * As Linus said, "C is a Spartan language, and so should your naming be." I * like these abbreviations, so we define them here. Note that u64 is always * unsigned long long, which works on all Linux systems: this means that we can - * use %llu in printf for any u64. */ + * use %llu in printf for any u64. + */ typedef unsigned long long u64; typedef uint32_t u32; typedef uint16_t u16; @@ -69,8 +73,10 @@ typedef uint8_t u8; /* This will occupy 3 pages: it must be a power of 2. */ #define VIRTQUEUE_NUM 256 -/*L:120 verbose is both a global flag and a macro. The C preprocessor allows - * this, and although I wouldn't recommend it, it works quite nicely here. */ +/*L:120 + * verbose is both a global flag and a macro. The C preprocessor allows + * this, and although I wouldn't recommend it, it works quite nicely here. + */ static bool verbose; #define verbose(args...) \ do { if (verbose) printf(args); } while(0) @@ -100,8 +106,7 @@ struct device_list /* A single linked list of devices. */ struct device *dev; - /* And a pointer to the last device for easy append and also for - * configuration appending. */ + /* And a pointer to the last device for easy append. */ struct device *lastdev; }; @@ -168,20 +173,24 @@ static char **main_args; /* The original tty settings to restore on exit. */ static struct termios orig_term; -/* We have to be careful with barriers: our devices are all run in separate +/* + * We have to be careful with barriers: our devices are all run in separate * threads and so we need to make sure that changes visible to the Guest happen - * in precise order. */ + * in precise order. + */ #define wmb() __asm__ __volatile__("" : : : "memory") #define mb() __asm__ __volatile__("" : : : "memory") -/* Convert an iovec element to the given type. +/* + * Convert an iovec element to the given type. * * This is a fairly ugly trick: we need to know the size of the type and * alignment requirement to check the pointer is kosher. It's also nice to * have the name of the type in case we report failure. * * Typing those three things all the time is cumbersome and error prone, so we - * have a macro which sets them all up and passes to the real function. */ + * have a macro which sets them all up and passes to the real function. + */ #define convert(iov, type) \ ((type *)_convert((iov), sizeof(type), __alignof__(type), #type)) @@ -198,8 +207,10 @@ static void *_convert(struct iovec *iov, size_t size, size_t align, /* Wrapper for the last available index. Makes it easier to change. */ #define lg_last_avail(vq) ((vq)->last_avail_idx) -/* The virtio configuration space is defined to be little-endian. x86 is - * little-endian too, but it's nice to be explicit so we have these helpers. */ +/* + * The virtio configuration space is defined to be little-endian. x86 is + * little-endian too, but it's nice to be explicit so we have these helpers. + */ #define cpu_to_le16(v16) (v16) #define cpu_to_le32(v32) (v32) #define cpu_to_le64(v64) (v64) @@ -241,11 +252,12 @@ static u8 *get_feature_bits(struct device *dev) + dev->num_vq * sizeof(struct lguest_vqconfig); } -/*L:100 The Launcher code itself takes us out into userspace, that scary place - * where pointers run wild and free! Unfortunately, like most userspace - * programs, it's quite boring (which is why everyone likes to hack on the - * kernel!). Perhaps if you make up an Lguest Drinking Game at this point, it - * will get you through this section. Or, maybe not. +/*L:100 + * The Launcher code itself takes us out into userspace, that scary place where + * pointers run wild and free! Unfortunately, like most userspace programs, + * it's quite boring (which is why everyone likes to hack on the kernel!). + * Perhaps if you make up an Lguest Drinking Game at this point, it will get + * you through this section. Or, maybe not. * * The Launcher sets up a big chunk of memory to be the Guest's "physical" * memory and stores it in "guest_base". In other words, Guest physical == @@ -253,7 +265,8 @@ static u8 *get_feature_bits(struct device *dev) * * This can be tough to get your head around, but usually it just means that we * use these trivial conversion functions when the Guest gives us it's - * "physical" addresses: */ + * "physical" addresses: + */ static void *from_guest_phys(unsigned long addr) { return guest_base + addr; @@ -268,7 +281,8 @@ static unsigned long to_guest_phys(const void *addr) * Loading the Kernel. * * We start with couple of simple helper routines. open_or_die() avoids - * error-checking code cluttering the callers: */ + * error-checking code cluttering the callers: + */ static int open_or_die(const char *name, int flags) { int fd = open(name, flags); @@ -283,8 +297,10 @@ static void *map_zeroed_pages(unsigned int num) int fd = open_or_die("/dev/zero", O_RDONLY); void *addr; - /* We use a private mapping (ie. if we write to the page, it will be - * copied). */ + /* + * We use a private mapping (ie. if we write to the page, it will be + * copied). + */ addr = mmap(NULL, getpagesize() * num, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0); if (addr == MAP_FAILED) @@ -305,20 +321,24 @@ static void *get_pages(unsigned int num) return addr; } -/* This routine is used to load the kernel or initrd. It tries mmap, but if +/* + * This routine is used to load the kernel or initrd. It tries mmap, but if * that fails (Plan 9's kernel file isn't nicely aligned on page boundaries), - * it falls back to reading the memory in. */ + * it falls back to reading the memory in. + */ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) { ssize_t r; - /* We map writable even though for some segments are marked read-only. + /* + * We map writable even though for some segments are marked read-only. * The kernel really wants to be writable: it patches its own * instructions. * * MAP_PRIVATE means that the page won't be copied until a write is * done to it. This allows us to share untouched memory between - * Guests. */ + * Guests. + */ if (mmap(addr, len, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_FIXED|MAP_PRIVATE, fd, offset) != MAP_FAILED) return; @@ -329,7 +349,8 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) err(1, "Reading offset %lu len %lu gave %zi", offset, len, r); } -/* This routine takes an open vmlinux image, which is in ELF, and maps it into +/* + * This routine takes an open vmlinux image, which is in ELF, and maps it into * the Guest memory. ELF = Embedded Linking Format, which is the format used * by all modern binaries on Linux including the kernel. * @@ -337,23 +358,28 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len) * address. We use the physical address; the Guest will map itself to the * virtual address. * - * We return the starting address. */ + * We return the starting address. + */ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) { Elf32_Phdr phdr[ehdr->e_phnum]; unsigned int i; - /* Sanity checks on the main ELF header: an x86 executable with a - * reasonable number of correctly-sized program headers. */ + /* + * Sanity checks on the main ELF header: an x86 executable with a + * reasonable number of correctly-sized program headers. + */ if (ehdr->e_type != ET_EXEC || ehdr->e_machine != EM_386 || ehdr->e_phentsize != sizeof(Elf32_Phdr) || ehdr->e_phnum < 1 || ehdr->e_phnum > 65536U/sizeof(Elf32_Phdr)) errx(1, "Malformed elf header"); - /* An ELF executable contains an ELF header and a number of "program" + /* + * An ELF executable contains an ELF header and a number of "program" * headers which indicate which parts ("segments") of the program to - * load where. */ + * load where. + */ /* We read in all the program headers at once: */ if (lseek(elf_fd, ehdr->e_phoff, SEEK_SET) < 0) @@ -361,8 +387,10 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) if (read(elf_fd, phdr, sizeof(phdr)) != sizeof(phdr)) err(1, "Reading program headers"); - /* Try all the headers: there are usually only three. A read-only one, - * a read-write one, and a "note" section which we don't load. */ + /* + * Try all the headers: there are usually only three. A read-only one, + * a read-write one, and a "note" section which we don't load. + */ for (i = 0; i < ehdr->e_phnum; i++) { /* If this isn't a loadable segment, we ignore it */ if (phdr[i].p_type != PT_LOAD) @@ -380,13 +408,15 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr) return ehdr->e_entry; } -/*L:150 A bzImage, unlike an ELF file, is not meant to be loaded. You're - * supposed to jump into it and it will unpack itself. We used to have to - * perform some hairy magic because the unpacking code scared me. +/*L:150 + * A bzImage, unlike an ELF file, is not meant to be loaded. You're supposed + * to jump into it and it will unpack itself. We used to have to perform some + * hairy magic because the unpacking code scared me. * * Fortunately, Jeremy Fitzhardinge convinced me it wasn't that hard and wrote * a small patch to jump over the tricky bits in the Guest, so now we just read - * the funky header so we know where in the file to load, and away we go! */ + * the funky header so we know where in the file to load, and away we go! + */ static unsigned long load_bzimage(int fd) { struct boot_params boot; @@ -394,8 +424,10 @@ static unsigned long load_bzimage(int fd) /* Modern bzImages get loaded at 1M. */ void *p = from_guest_phys(0x100000); - /* Go back to the start of the file and read the header. It should be - * a Linux boot header (see Documentation/x86/i386/boot.txt) */ + /* + * Go back to the start of the file and read the header. It should be + * a Linux boot header (see Documentation/x86/i386/boot.txt) + */ lseek(fd, 0, SEEK_SET); read(fd, &boot, sizeof(boot)); @@ -414,9 +446,11 @@ static unsigned long load_bzimage(int fd) return boot.hdr.code32_start; } -/*L:140 Loading the kernel is easy when it's a "vmlinux", but most kernels +/*L:140 + * Loading the kernel is easy when it's a "vmlinux", but most kernels * come wrapped up in the self-decompressing "bzImage" format. With a little - * work, we can load those, too. */ + * work, we can load those, too. + */ static unsigned long load_kernel(int fd) { Elf32_Ehdr hdr; @@ -433,24 +467,28 @@ static unsigned long load_kernel(int fd) return load_bzimage(fd); } -/* This is a trivial little helper to align pages. Andi Kleen hated it because +/* + * This is a trivial little helper to align pages. Andi Kleen hated it because * it calls getpagesize() twice: "it's dumb code." * * Kernel guys get really het up about optimization, even when it's not - * necessary. I leave this code as a reaction against that. */ + * necessary. I leave this code as a reaction against that. + */ static inline unsigned long page_align(unsigned long addr) { /* Add upwards and truncate downwards. */ return ((addr + getpagesize()-1) & ~(getpagesize()-1)); } -/*L:180 An "initial ram disk" is a disk image loaded into memory along with - * the kernel which the kernel can use to boot from without needing any - * drivers. Most distributions now use this as standard: the initrd contains - * the code to load the appropriate driver modules for the current machine. +/*L:180 + * An "initial ram disk" is a disk image loaded into memory along with the + * kernel which the kernel can use to boot from without needing any drivers. + * Most distributions now use this as standard: the initrd contains the code to + * load the appropriate driver modules for the current machine. * * Importantly, James Morris works for RedHat, and Fedora uses initrds for its - * kernels. He sent me this (and tells me when I break it). */ + * kernels. He sent me this (and tells me when I break it). + */ static unsigned long load_initrd(const char *name, unsigned long mem) { int ifd; @@ -462,12 +500,16 @@ static unsigned long load_initrd(const char *name, unsigned long mem) if (fstat(ifd, &st) < 0) err(1, "fstat() on initrd '%s'", name); - /* We map the initrd at the top of memory, but mmap wants it to be - * page-aligned, so we round the size up for that. */ + /* + * We map the initrd at the top of memory, but mmap wants it to be + * page-aligned, so we round the size up for that. + */ len = page_align(st.st_size); map_at(ifd, from_guest_phys(mem - len), 0, st.st_size); - /* Once a file is mapped, you can close the file descriptor. It's a - * little odd, but quite useful. */ + /* + * Once a file is mapped, you can close the file descriptor. It's a + * little odd, but quite useful. + */ close(ifd); verbose("mapped initrd %s size=%lu @ %p\n", name, len, (void*)mem-len); @@ -476,8 +518,10 @@ static unsigned long load_initrd(const char *name, unsigned long mem) } /*:*/ -/* Simple routine to roll all the commandline arguments together with spaces - * between them. */ +/* + * Simple routine to roll all the commandline arguments together with spaces + * between them. + */ static void concat(char *dst, char *args[]) { unsigned int i, len = 0; @@ -494,10 +538,12 @@ static void concat(char *dst, char *args[]) dst[len] = '\0'; } -/*L:185 This is where we actually tell the kernel to initialize the Guest. We +/*L:185 + * This is where we actually tell the kernel to initialize the Guest. We * saw the arguments it expects when we looked at initialize() in lguest_user.c: * the base of Guest "physical" memory, the top physical page to allow and the - * entry point for the Guest. */ + * entry point for the Guest. + */ static void tell_kernel(unsigned long start) { unsigned long args[] = { LHREQ_INITIALIZE, @@ -522,20 +568,26 @@ static void tell_kernel(unsigned long start) static void *_check_pointer(unsigned long addr, unsigned int size, unsigned int line) { - /* We have to separately check addr and addr+size, because size could - * be huge and addr + size might wrap around. */ + /* + * We have to separately check addr and addr+size, because size could + * be huge and addr + size might wrap around. + */ if (addr >= guest_limit || addr + size >= guest_limit) errx(1, "%s:%i: Invalid address %#lx", __FILE__, line, addr); - /* We return a pointer for the caller's convenience, now we know it's - * safe to use. */ + /* + * We return a pointer for the caller's convenience, now we know it's + * safe to use. + */ return from_guest_phys(addr); } /* A macro which transparently hands the line number to the real function. */ #define check_pointer(addr,size) _check_pointer(addr, size, __LINE__) -/* Each buffer in the virtqueues is actually a chain of descriptors. This +/* + * Each buffer in the virtqueues is actually a chain of descriptors. This * function returns the next descriptor in the chain, or vq->vring.num if we're - * at the end. */ + * at the end. + */ static unsigned next_desc(struct vring_desc *desc, unsigned int i, unsigned int max) { @@ -576,12 +628,14 @@ static void trigger_irq(struct virtqueue *vq) err(1, "Triggering irq %i", vq->config.irq); } -/* This looks in the virtqueue and for the first available buffer, and converts +/* + * This looks in the virtqueue and for the first available buffer, and converts * it to an iovec for convenient access. Since descriptors consist of some * number of output then some number of input descriptors, it's actually two * iovecs, but we pack them into one and note how many of each there were. * - * This function returns the descriptor number found. */ + * This function returns the descriptor number found. + */ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct iovec iov[], unsigned int *out_num, unsigned int *in_num) @@ -599,8 +653,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, /* OK, now we need to know about added descriptors. */ vq->vring.used->flags &= ~VRING_USED_F_NO_NOTIFY; - /* They could have slipped one in as we were doing that: make - * sure it's written, then check again. */ + /* + * They could have slipped one in as we were doing that: make + * sure it's written, then check again. + */ mb(); if (last_avail != vq->vring.avail->idx) { vq->vring.used->flags |= VRING_USED_F_NO_NOTIFY; @@ -620,8 +676,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, errx(1, "Guest moved used index from %u to %u", last_avail, vq->vring.avail->idx); - /* Grab the next descriptor number they're advertising, and increment - * the index we've seen. */ + /* + * Grab the next descriptor number they're advertising, and increment + * the index we've seen. + */ head = vq->vring.avail->ring[last_avail % vq->vring.num]; lg_last_avail(vq)++; @@ -636,8 +694,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, desc = vq->vring.desc; i = head; - /* If this is an indirect entry, then this buffer contains a descriptor - * table which we handle as if it's any normal descriptor chain. */ + /* + * If this is an indirect entry, then this buffer contains a descriptor + * table which we handle as if it's any normal descriptor chain. + */ if (desc[i].flags & VRING_DESC_F_INDIRECT) { if (desc[i].len % sizeof(struct vring_desc)) errx(1, "Invalid size for indirect buffer table"); @@ -656,8 +716,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, if (desc[i].flags & VRING_DESC_F_WRITE) (*in_num)++; else { - /* If it's an output descriptor, they're all supposed - * to come before any input descriptors. */ + /* + * If it's an output descriptor, they're all supposed + * to come before any input descriptors. + */ if (*in_num) errx(1, "Descriptor has out after in"); (*out_num)++; @@ -671,14 +733,18 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, return head; } -/* After we've used one of their buffers, we tell them about it. We'll then - * want to send them an interrupt, using trigger_irq(). */ +/* + * After we've used one of their buffers, we tell them about it. We'll then + * want to send them an interrupt, using trigger_irq(). + */ static void add_used(struct virtqueue *vq, unsigned int head, int len) { struct vring_used_elem *used; - /* The virtqueue contains a ring of used buffers. Get a pointer to the - * next entry in that used ring. */ + /* + * The virtqueue contains a ring of used buffers. Get a pointer to the + * next entry in that used ring. + */ used = &vq->vring.used->ring[vq->vring.used->idx % vq->vring.num]; used->id = head; used->len = len; @@ -698,7 +764,8 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len) /* * The Console * - * We associate some data with the console for our exit hack. */ + * We associate some data with the console for our exit hack. + */ struct console_abort { /* How many times have they hit ^C? */ @@ -725,20 +792,24 @@ static void console_input(struct virtqueue *vq) if (len <= 0) { /* Ran out of input? */ warnx("Failed to get console input, ignoring console."); - /* For simplicity, dying threads kill the whole Launcher. So - * just nap here. */ + /* + * For simplicity, dying threads kill the whole Launcher. So + * just nap here. + */ for (;;) pause(); } add_used_and_trigger(vq, head, len); - /* Three ^C within one second? Exit. + /* + * Three ^C within one second? Exit. * * This is such a hack, but works surprisingly well. Each ^C has to * be in a buffer by itself, so they can't be too fast. But we check * that we get three within about a second, so they can't be too - * slow. */ + * slow. + */ if (len != 1 || ((char *)iov[0].iov_base)[0] != 3) { abort->count = 0; return; @@ -809,8 +880,7 @@ static bool will_block(int fd) return select(fd+1, &fdset, NULL, NULL, &zero) != 1; } -/* This is where we handle packets coming in from the tun device to our - * Guest. */ +/* This handles packets coming in from the tun device to our Guest. */ static void net_input(struct virtqueue *vq) { int len; @@ -842,8 +912,10 @@ static int do_thread(void *_vq) return 0; } -/* When a child dies, we kill our entire process group with SIGTERM. This - * also has the side effect that the shell restores the console for us! */ +/* + * When a child dies, we kill our entire process group with SIGTERM. This + * also has the side effect that the shell restores the console for us! + */ static void kill_launcher(int signal) { kill(0, SIGTERM); @@ -880,9 +952,10 @@ static void reset_device(struct device *dev) static void create_thread(struct virtqueue *vq) { - /* Create stack for thread and run it. Since stack grows - * upwards, we point the stack pointer to the end of this - * region. */ + /* + * Create stack for thread and run it. Since the stack grows upwards, + * we point the stack pointer to the end of this region. + */ char *stack = malloc(32768); unsigned long args[] = { LHREQ_EVENTFD, vq->config.pfn*getpagesize(), 0 }; @@ -981,8 +1054,11 @@ static void handle_output(unsigned long addr) } } - /* Early console write is done using notify on a nul-terminated string - * in Guest memory. */ + /* + * Early console write is done using notify on a nul-terminated string + * in Guest memory. It's also great for hacking debugging messages + * into a Guest. + */ if (addr >= guest_limit) errx(1, "Bad NOTIFY %#lx", addr); @@ -998,10 +1074,12 @@ static void handle_output(unsigned long addr) * routines to allocate and manage them. */ -/* The layout of the device page is a "struct lguest_device_desc" followed by a +/* + * The layout of the device page is a "struct lguest_device_desc" followed by a * number of virtqueue descriptors, then two sets of feature bits, then an * array of configuration bytes. This routine returns the configuration - * pointer. */ + * pointer. + */ static u8 *device_config(const struct device *dev) { return (void *)(dev->desc + 1) @@ -1009,9 +1087,11 @@ static u8 *device_config(const struct device *dev) + dev->feature_len * 2; } -/* This routine allocates a new "struct lguest_device_desc" from descriptor +/* + * This routine allocates a new "struct lguest_device_desc" from descriptor * table page just above the Guest's normal memory. It returns a pointer to - * that descriptor. */ + * that descriptor. + */ static struct lguest_device_desc *new_dev_desc(u16 type) { struct lguest_device_desc d = { .type = type }; @@ -1032,8 +1112,10 @@ static struct lguest_device_desc *new_dev_desc(u16 type) return memcpy(p, &d, sizeof(d)); } -/* Each device descriptor is followed by the description of its virtqueues. We - * specify how many descriptors the virtqueue is to have. */ +/* + * Each device descriptor is followed by the description of its virtqueues. We + * specify how many descriptors the virtqueue is to have. + */ static void add_virtqueue(struct device *dev, unsigned int num_descs, void (*service)(struct virtqueue *)) { @@ -1061,10 +1143,12 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, /* Initialize the vring. */ vring_init(&vq->vring, num_descs, p, LGUEST_VRING_ALIGN); - /* Append virtqueue to this device's descriptor. We use + /* + * Append virtqueue to this device's descriptor. We use * device_config() to get the end of the device's current virtqueues; * we check that we haven't added any config or feature information - * yet, otherwise we'd be overwriting them. */ + * yet, otherwise we'd be overwriting them. + */ assert(dev->desc->config_len == 0 && dev->desc->feature_len == 0); memcpy(device_config(dev), &vq->config, sizeof(vq->config)); dev->num_vq++; @@ -1072,14 +1156,18 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, verbose("Virtqueue page %#lx\n", to_guest_phys(p)); - /* Add to tail of list, so dev->vq is first vq, dev->vq->next is - * second. */ + /* + * Add to tail of list, so dev->vq is first vq, dev->vq->next is + * second. + */ for (i = &dev->vq; *i; i = &(*i)->next); *i = vq; } -/* The first half of the feature bitmask is for us to advertise features. The - * second half is for the Guest to accept features. */ +/* + * The first half of the feature bitmask is for us to advertise features. The + * second half is for the Guest to accept features. + */ static void add_feature(struct device *dev, unsigned bit) { u8 *features = get_feature_bits(dev); @@ -1093,9 +1181,11 @@ static void add_feature(struct device *dev, unsigned bit) features[bit / CHAR_BIT] |= (1 << (bit % CHAR_BIT)); } -/* This routine sets the configuration fields for an existing device's +/* + * This routine sets the configuration fields for an existing device's * descriptor. It only works for the last device, but that's OK because that's - * how we use it. */ + * how we use it. + */ static void set_config(struct device *dev, unsigned len, const void *conf) { /* Check we haven't overflowed our single page. */ @@ -1110,10 +1200,12 @@ static void set_config(struct device *dev, unsigned len, const void *conf) assert(dev->desc->config_len == len); } -/* This routine does all the creation and setup of a new device, including +/* + * This routine does all the creation and setup of a new device, including * calling new_dev_desc() to allocate the descriptor and device memory. * - * See what I mean about userspace being boring? */ + * See what I mean about userspace being boring? + */ static struct device *new_device(const char *name, u16 type) { struct device *dev = malloc(sizeof(*dev)); @@ -1126,10 +1218,12 @@ static struct device *new_device(const char *name, u16 type) dev->num_vq = 0; dev->running = false; - /* Append to device list. Prepending to a single-linked list is + /* + * Append to device list. Prepending to a single-linked list is * easier, but the user expects the devices to be arranged on the bus * in command-line order. The first network device on the command line - * is eth0, the first block device /dev/vda, etc. */ + * is eth0, the first block device /dev/vda, etc. + */ if (devices.lastdev) devices.lastdev->next = dev; else @@ -1139,8 +1233,10 @@ static struct device *new_device(const char *name, u16 type) return dev; } -/* Our first setup routine is the console. It's a fairly simple device, but - * UNIX tty handling makes it uglier than it could be. */ +/* + * Our first setup routine is the console. It's a fairly simple device, but + * UNIX tty handling makes it uglier than it could be. + */ static void setup_console(void) { struct device *dev; @@ -1148,8 +1244,10 @@ static void setup_console(void) /* If we can save the initial standard input settings... */ if (tcgetattr(STDIN_FILENO, &orig_term) == 0) { struct termios term = orig_term; - /* Then we turn off echo, line buffering and ^C etc. We want a - * raw input stream to the Guest. */ + /* + * Then we turn off echo, line buffering and ^C etc: We want a + * raw input stream to the Guest. + */ term.c_lflag &= ~(ISIG|ICANON|ECHO); tcsetattr(STDIN_FILENO, TCSANOW, &term); } @@ -1160,10 +1258,12 @@ static void setup_console(void) dev->priv = malloc(sizeof(struct console_abort)); ((struct console_abort *)dev->priv)->count = 0; - /* The console needs two virtqueues: the input then the output. When + /* + * The console needs two virtqueues: the input then the output. When * they put something the input queue, we make sure we're listening to * stdin. When they put something in the output queue, we write it to - * stdout. */ + * stdout. + */ add_virtqueue(dev, VIRTQUEUE_NUM, console_input); add_virtqueue(dev, VIRTQUEUE_NUM, console_output); @@ -1171,7 +1271,8 @@ static void setup_console(void) } /*:*/ -/*M:010 Inter-guest networking is an interesting area. Simplest is to have a +/*M:010 + * Inter-guest networking is an interesting area. Simplest is to have a * --sharenet= option which opens or creates a named pipe. This can be * used to send packets to another guest in a 1:1 manner. * @@ -1185,7 +1286,8 @@ static void setup_console(void) * multiple inter-guest channels behind one interface, although it would * require some manner of hotplugging new virtio channels. * - * Finally, we could implement a virtio network switch in the kernel. :*/ + * Finally, we could implement a virtio network switch in the kernel. +:*/ static u32 str2ip(const char *ipaddr) { @@ -1210,11 +1312,13 @@ static void str2mac(const char *macaddr, unsigned char mac[6]) mac[5] = m[5]; } -/* This code is "adapted" from libbridge: it attaches the Host end of the +/* + * This code is "adapted" from libbridge: it attaches the Host end of the * network device to the bridge device specified by the command line. * * This is yet another James Morris contribution (I'm an IP-level guy, so I - * dislike bridging), and I just try not to break it. */ + * dislike bridging), and I just try not to break it. + */ static void add_to_bridge(int fd, const char *if_name, const char *br_name) { int ifidx; @@ -1234,9 +1338,11 @@ static void add_to_bridge(int fd, const char *if_name, const char *br_name) err(1, "can't add %s to bridge %s", if_name, br_name); } -/* This sets up the Host end of the network device with an IP address, brings +/* + * This sets up the Host end of the network device with an IP address, brings * it up so packets will flow, the copies the MAC address into the hwaddr - * pointer. */ + * pointer. + */ static void configure_device(int fd, const char *tapif, u32 ipaddr) { struct ifreq ifr; @@ -1263,10 +1369,12 @@ static int get_tun_device(char tapif[IFNAMSIZ]) /* Start with this zeroed. Messy but sure. */ memset(&ifr, 0, sizeof(ifr)); - /* We open the /dev/net/tun device and tell it we want a tap device. A + /* + * We open the /dev/net/tun device and tell it we want a tap device. A * tap device is like a tun device, only somehow different. To tell * the truth, I completely blundered my way through this code, but it - * works now! */ + * works now! + */ netfd = open_or_die("/dev/net/tun", O_RDWR); ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_VNET_HDR; strcpy(ifr.ifr_name, "tap%d"); @@ -1277,18 +1385,22 @@ static int get_tun_device(char tapif[IFNAMSIZ]) TUN_F_CSUM|TUN_F_TSO4|TUN_F_TSO6|TUN_F_TSO_ECN) != 0) err(1, "Could not set features for tun device"); - /* We don't need checksums calculated for packets coming in this - * device: trust us! */ + /* + * We don't need checksums calculated for packets coming in this + * device: trust us! + */ ioctl(netfd, TUNSETNOCSUM, 1); memcpy(tapif, ifr.ifr_name, IFNAMSIZ); return netfd; } -/*L:195 Our network is a Host<->Guest network. This can either use bridging or +/*L:195 + * Our network is a Host<->Guest network. This can either use bridging or * routing, but the principle is the same: it uses the "tun" device to inject * packets into the Host as if they came in from a normal network card. We - * just shunt packets between the Guest and the tun device. */ + * just shunt packets between the Guest and the tun device. + */ static void setup_tun_net(char *arg) { struct device *dev; @@ -1305,13 +1417,14 @@ static void setup_tun_net(char *arg) dev = new_device("net", VIRTIO_ID_NET); dev->priv = net_info; - /* Network devices need a receive and a send queue, just like - * console. */ + /* Network devices need a recv and a send queue, just like console. */ add_virtqueue(dev, VIRTQUEUE_NUM, net_input); add_virtqueue(dev, VIRTQUEUE_NUM, net_output); - /* We need a socket to perform the magic network ioctls to bring up the - * tap interface, connect to the bridge etc. Any socket will do! */ + /* + * We need a socket to perform the magic network ioctls to bring up the + * tap interface, connect to the bridge etc. Any socket will do! + */ ipfd = socket(PF_INET, SOCK_DGRAM, IPPROTO_IP); if (ipfd < 0) err(1, "opening IP socket"); @@ -1366,7 +1479,8 @@ static void setup_tun_net(char *arg) devices.device_num, tapif, arg); } -/* Our block (disk) device should be really simple: the Guest asks for a block +/* + * Our block (disk) device should be really simple: the Guest asks for a block * number and we read or write that position in the file. Unfortunately, that * was amazingly slow: the Guest waits until the read is finished before * running anything else, even if it could have been doing useful work. @@ -1374,7 +1488,9 @@ static void setup_tun_net(char *arg) * We could use async I/O, except it's reputed to suck so hard that characters * actually go missing from your code when you try to use it. * - * So we farm the I/O out to thread, and communicate with it via a pipe. */ + * So this was one reason why lguest now does all virtqueue servicing in + * separate threads: it's more efficient and more like a real device. + */ /* This hangs off device->priv. */ struct vblk_info @@ -1412,9 +1528,11 @@ static void blk_request(struct virtqueue *vq) /* Get the next request. */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); - /* Every block request should contain at least one output buffer + /* + * Every block request should contain at least one output buffer * (detailing the location on disk and the type of request) and one - * input buffer (to hold the result). */ + * input buffer (to hold the result). + */ if (out_num == 0 || in_num == 0) errx(1, "Bad virtblk cmd %u out=%u in=%u", head, out_num, in_num); @@ -1423,33 +1541,41 @@ static void blk_request(struct virtqueue *vq) in = convert(&iov[out_num+in_num-1], u8); off = out->sector * 512; - /* The block device implements "barriers", where the Guest indicates + /* + * The block device implements "barriers", where the Guest indicates * that it wants all previous writes to occur before this write. We * don't have a way of asking our kernel to do a barrier, so we just - * synchronize all the data in the file. Pretty poor, no? */ + * synchronize all the data in the file. Pretty poor, no? + */ if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); - /* In general the virtio block driver is allowed to try SCSI commands. - * It'd be nice if we supported eject, for example, but we don't. */ + /* + * In general the virtio block driver is allowed to try SCSI commands. + * It'd be nice if we supported eject, for example, but we don't. + */ if (out->type & VIRTIO_BLK_T_SCSI_CMD) { fprintf(stderr, "Scsi commands unsupported\n"); *in = VIRTIO_BLK_S_UNSUPP; wlen = sizeof(*in); } else if (out->type & VIRTIO_BLK_T_OUT) { - /* Write */ - - /* Move to the right location in the block file. This can fail - * if they try to write past end. */ + /* + * Write + * + * Move to the right location in the block file. This can fail + * if they try to write past end. + */ if (lseek64(vblk->fd, off, SEEK_SET) != off) err(1, "Bad seek to sector %llu", out->sector); ret = writev(vblk->fd, iov+1, out_num-1); verbose("WRITE to sector %llu: %i\n", out->sector, ret); - /* Grr... Now we know how long the descriptor they sent was, we + /* + * Grr... Now we know how long the descriptor they sent was, we * make sure they didn't try to write over the end of the block - * file (possibly extending it). */ + * file (possibly extending it). + */ if (ret > 0 && off + ret > vblk->len) { /* Trim it back to the correct length */ ftruncate64(vblk->fd, vblk->len); @@ -1459,10 +1585,12 @@ static void blk_request(struct virtqueue *vq) wlen = sizeof(*in); *in = (ret >= 0 ? VIRTIO_BLK_S_OK : VIRTIO_BLK_S_IOERR); } else { - /* Read */ - - /* Move to the right location in the block file. This can fail - * if they try to read past end. */ + /* + * Read + * + * Move to the right location in the block file. This can fail + * if they try to read past end. + */ if (lseek64(vblk->fd, off, SEEK_SET) != off) err(1, "Bad seek to sector %llu", out->sector); @@ -1477,10 +1605,12 @@ static void blk_request(struct virtqueue *vq) } } - /* OK, so we noted that it was pretty poor to use an fdatasync as a + /* + * OK, so we noted that it was pretty poor to use an fdatasync as a * barrier. But Christoph Hellwig points out that we need a sync * *afterwards* as well: "Barriers specify no reordering to the front - * or the back." And Jens Axboe confirmed it, so here we are: */ + * or the back." And Jens Axboe confirmed it, so here we are: + */ if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); @@ -1494,7 +1624,7 @@ static void setup_block_file(const char *filename) struct vblk_info *vblk; struct virtio_blk_config conf; - /* The device responds to return from I/O thread. */ + /* Creat the device. */ dev = new_device("block", VIRTIO_ID_BLOCK); /* The device has one virtqueue, where the Guest places requests. */ @@ -1513,8 +1643,10 @@ static void setup_block_file(const char *filename) /* Tell Guest how many sectors this device has. */ conf.capacity = cpu_to_le64(vblk->len / 512); - /* Tell Guest not to put in too many descriptors at once: two are used - * for the in and out elements. */ + /* + * Tell Guest not to put in too many descriptors at once: two are used + * for the in and out elements. + */ add_feature(dev, VIRTIO_BLK_F_SEG_MAX); conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2); @@ -1525,16 +1657,18 @@ static void setup_block_file(const char *filename) ++devices.device_num, le64_to_cpu(conf.capacity)); } -struct rng_info { - int rfd; -}; - -/* Our random number generator device reads from /dev/random into the Guest's +/*L:211 + * Our random number generator device reads from /dev/random into the Guest's * input buffers. The usual case is that the Guest doesn't want random numbers * and so has no buffers although /dev/random is still readable, whereas * console is the reverse. * - * The same logic applies, however. */ + * The same logic applies, however. + */ +struct rng_info { + int rfd; +}; + static void rng_input(struct virtqueue *vq) { int len; @@ -1547,9 +1681,11 @@ static void rng_input(struct virtqueue *vq) if (out_num) errx(1, "Output buffers in rng?"); - /* This is why we convert to iovecs: the readv() call uses them, and so + /* + * This is why we convert to iovecs: the readv() call uses them, and so * it reads straight into the Guest's buffer. We loop to make sure we - * fill it. */ + * fill it. + */ while (!iov_empty(iov, in_num)) { len = readv(rng_info->rfd, iov, in_num); if (len <= 0) @@ -1562,15 +1698,18 @@ static void rng_input(struct virtqueue *vq) add_used(vq, head, totlen); } -/* And this creates a "hardware" random number device for the Guest. */ +/*L:199 + * This creates a "hardware" random number device for the Guest. + */ static void setup_rng(void) { struct device *dev; struct rng_info *rng_info = malloc(sizeof(*rng_info)); + /* Our device's privat info simply contains the /dev/random fd. */ rng_info->rfd = open_or_die("/dev/random", O_RDONLY); - /* The device responds to return from I/O thread. */ + /* Create the new device. */ dev = new_device("rng", VIRTIO_ID_RNG); dev->priv = rng_info; @@ -1586,8 +1725,10 @@ static void __attribute__((noreturn)) restart_guest(void) { unsigned int i; - /* Since we don't track all open fds, we simply close everything beyond - * stderr. */ + /* + * Since we don't track all open fds, we simply close everything beyond + * stderr. + */ for (i = 3; i < FD_SETSIZE; i++) close(i); @@ -1598,8 +1739,10 @@ static void __attribute__((noreturn)) restart_guest(void) err(1, "Could not exec %s", main_args[0]); } -/*L:220 Finally we reach the core of the Launcher which runs the Guest, serves - * its input and output, and finally, lays it to rest. */ +/*L:220 + * Finally we reach the core of the Launcher which runs the Guest, serves + * its input and output, and finally, lays it to rest. + */ static void __attribute__((noreturn)) run_guest(void) { for (;;) { @@ -1634,7 +1777,7 @@ static void __attribute__((noreturn)) run_guest(void) * * Are you ready? Take a deep breath and join me in the core of the Host, in * "make Host". - :*/ +:*/ static struct option opts[] = { { "verbose", 0, NULL, 'v' }, @@ -1655,8 +1798,7 @@ static void usage(void) /*L:105 The main routine is where the real work begins: */ int main(int argc, char *argv[]) { - /* Memory, top-level pagetable, code startpoint and size of the - * (optional) initrd. */ + /* Memory, code startpoint and size of the (optional) initrd. */ unsigned long mem = 0, start, initrd_size = 0; /* Two temporaries. */ int i, c; @@ -1668,24 +1810,30 @@ int main(int argc, char *argv[]) /* Save the args: we "reboot" by execing ourselves again. */ main_args = argv; - /* First we initialize the device list. We keep a pointer to the last + /* + * First we initialize the device list. We keep a pointer to the last * device, and the next interrupt number to use for devices (1: - * remember that 0 is used by the timer). */ + * remember that 0 is used by the timer). + */ devices.lastdev = NULL; devices.next_irq = 1; cpu_id = 0; - /* We need to know how much memory so we can set up the device + /* + * We need to know how much memory so we can set up the device * descriptor and memory pages for the devices as we parse the command * line. So we quickly look through the arguments to find the amount - * of memory now. */ + * of memory now. + */ for (i = 1; i < argc; i++) { if (argv[i][0] != '-') { mem = atoi(argv[i]) * 1024 * 1024; - /* We start by mapping anonymous pages over all of + /* + * We start by mapping anonymous pages over all of * guest-physical memory range. This fills it with 0, * and ensures that the Guest won't be killed when it - * tries to access it. */ + * tries to access it. + */ guest_base = map_zeroed_pages(mem / getpagesize() + DEVICE_PAGES); guest_limit = mem; @@ -1718,8 +1866,10 @@ int main(int argc, char *argv[]) usage(); } } - /* After the other arguments we expect memory and kernel image name, - * followed by command line arguments for the kernel. */ + /* + * After the other arguments we expect memory and kernel image name, + * followed by command line arguments for the kernel. + */ if (optind + 2 > argc) usage(); @@ -1737,20 +1887,26 @@ int main(int argc, char *argv[]) /* Map the initrd image if requested (at top of physical memory) */ if (initrd_name) { initrd_size = load_initrd(initrd_name, mem); - /* These are the location in the Linux boot header where the - * start and size of the initrd are expected to be found. */ + /* + * These are the location in the Linux boot header where the + * start and size of the initrd are expected to be found. + */ boot->hdr.ramdisk_image = mem - initrd_size; boot->hdr.ramdisk_size = initrd_size; /* The bootloader type 0xFF means "unknown"; that's OK. */ boot->hdr.type_of_loader = 0xFF; } - /* The Linux boot header contains an "E820" memory map: ours is a - * simple, single region. */ + /* + * The Linux boot header contains an "E820" memory map: ours is a + * simple, single region. + */ boot->e820_entries = 1; boot->e820_map[0] = ((struct e820entry) { 0, mem, E820_RAM }); - /* The boot header contains a command line pointer: we put the command - * line after the boot header. */ + /* + * The boot header contains a command line pointer: we put the command + * line after the boot header. + */ boot->hdr.cmd_line_ptr = to_guest_phys(boot + 1); /* We use a simple helper to copy the arguments separated by spaces. */ concat((char *)(boot + 1), argv+optind+2); @@ -1764,8 +1920,10 @@ int main(int argc, char *argv[]) /* Tell the entry path not to try to reload segment registers. */ boot->hdr.loadflags |= KEEP_SEGMENTS; - /* We tell the kernel to initialize the Guest: this returns the open - * /dev/lguest file descriptor. */ + /* + * We tell the kernel to initialize the Guest: this returns the open + * /dev/lguest file descriptor. + */ tell_kernel(start); /* Ensure that we terminate if a child dies. */ diff --git a/arch/x86/include/asm/lguest.h b/arch/x86/include/asm/lguest.h index 313389cd50d2..5136dad57cbb 100644 --- a/arch/x86/include/asm/lguest.h +++ b/arch/x86/include/asm/lguest.h @@ -17,8 +17,7 @@ /* Pages for switcher itself, then two pages per cpu */ #define TOTAL_SWITCHER_PAGES (SHARED_SWITCHER_PAGES + 2 * nr_cpu_ids) -/* We map at -4M (-2M when PAE is activated) for ease of mapping - * into the guest (one PTE page). */ +/* We map at -4M (-2M for PAE) for ease of mapping (one PTE page). */ #ifdef CONFIG_X86_PAE #define SWITCHER_ADDR 0xFFE00000 #else diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h index 33600a66755f..cceb73e12e50 100644 --- a/arch/x86/include/asm/lguest_hcall.h +++ b/arch/x86/include/asm/lguest_hcall.h @@ -30,7 +30,8 @@ #include #include -/*G:030 But first, how does our Guest contact the Host to ask for privileged +/*G:030 + * But first, how does our Guest contact the Host to ask for privileged * operations? There are two ways: the direct way is to make a "hypercall", * to make requests of the Host Itself. * @@ -41,16 +42,15 @@ * * Grossly invalid calls result in Sudden Death at the hands of the vengeful * Host, rather than returning failure. This reflects Winston Churchill's - * definition of a gentleman: "someone who is only rude intentionally". */ -/*:*/ + * definition of a gentleman: "someone who is only rude intentionally". +:*/ /* Can't use our min() macro here: needs to be a constant */ #define LGUEST_IRQS (NR_IRQS < 32 ? NR_IRQS: 32) #define LHCALL_RING_SIZE 64 struct hcall_args { - /* These map directly onto eax, ebx, ecx, edx and esi - * in struct lguest_regs */ + /* These map directly onto eax/ebx/ecx/edx/esi in struct lguest_regs */ unsigned long arg0, arg1, arg2, arg3, arg4; }; diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c index f2bf1f73d468..025c04d18f2b 100644 --- a/arch/x86/lguest/boot.c +++ b/arch/x86/lguest/boot.c @@ -22,7 +22,8 @@ * * So how does the kernel know it's a Guest? We'll see that later, but let's * just say that we end up here where we replace the native functions various - * "paravirt" structures with our Guest versions, then boot like normal. :*/ + * "paravirt" structures with our Guest versions, then boot like normal. +:*/ /* * Copyright (C) 2006, Rusty Russell IBM Corporation. @@ -74,7 +75,8 @@ * * The Guest in our tale is a simple creature: identical to the Host but * behaving in simplified but equivalent ways. In particular, the Guest is the - * same kernel as the Host (or at least, built from the same source code). :*/ + * same kernel as the Host (or at least, built from the same source code). +:*/ struct lguest_data lguest_data = { .hcall_status = { [0 ... LHCALL_RING_SIZE-1] = 0xFF }, @@ -85,7 +87,8 @@ struct lguest_data lguest_data = { .syscall_vec = SYSCALL_VECTOR, }; -/*G:037 async_hcall() is pretty simple: I'm quite proud of it really. We have a +/*G:037 + * async_hcall() is pretty simple: I'm quite proud of it really. We have a * ring buffer of stored hypercalls which the Host will run though next time we * do a normal hypercall. Each entry in the ring has 5 slots for the hypercall * arguments, and a "hcall_status" word which is 0 if the call is ready to go, @@ -94,7 +97,8 @@ struct lguest_data lguest_data = { * If we come around to a slot which hasn't been finished, then the table is * full and we just make the hypercall directly. This has the nice side * effect of causing the Host to run all the stored calls in the ring buffer - * which empties it for next time! */ + * which empties it for next time! + */ static void async_hcall(unsigned long call, unsigned long arg1, unsigned long arg2, unsigned long arg3, unsigned long arg4) @@ -103,9 +107,11 @@ static void async_hcall(unsigned long call, unsigned long arg1, static unsigned int next_call; unsigned long flags; - /* Disable interrupts if not already disabled: we don't want an + /* + * Disable interrupts if not already disabled: we don't want an * interrupt handler making a hypercall while we're already doing - * one! */ + * one! + */ local_irq_save(flags); if (lguest_data.hcall_status[next_call] != 0xFF) { /* Table full, so do normal hcall which will flush table. */ @@ -125,8 +131,9 @@ static void async_hcall(unsigned long call, unsigned long arg1, local_irq_restore(flags); } -/*G:035 Notice the lazy_hcall() above, rather than hcall(). This is our first - * real optimization trick! +/*G:035 + * Notice the lazy_hcall() above, rather than hcall(). This is our first real + * optimization trick! * * When lazy_mode is set, it means we're allowed to defer all hypercalls and do * them as a batch when lazy_mode is eventually turned off. Because hypercalls @@ -136,7 +143,8 @@ static void async_hcall(unsigned long call, unsigned long arg1, * lguest_leave_lazy_mode(). * * So, when we're in lazy mode, we call async_hcall() to store the call for - * future processing: */ + * future processing: + */ static void lazy_hcall1(unsigned long call, unsigned long arg1) { @@ -208,9 +216,11 @@ static void lguest_end_context_switch(struct task_struct *next) * check there before it tries to deliver an interrupt. */ -/* save_flags() is expected to return the processor state (ie. "flags"). The +/* + * save_flags() is expected to return the processor state (ie. "flags"). The * flags word contains all kind of stuff, but in practice Linux only cares - * about the interrupt flag. Our "save_flags()" just returns that. */ + * about the interrupt flag. Our "save_flags()" just returns that. + */ static unsigned long save_fl(void) { return lguest_data.irq_enabled; @@ -222,13 +232,15 @@ static void irq_disable(void) lguest_data.irq_enabled = 0; } -/* Let's pause a moment. Remember how I said these are called so often? +/* + * Let's pause a moment. Remember how I said these are called so often? * Jeremy Fitzhardinge optimized them so hard early in 2009 that he had to * break some rules. In particular, these functions are assumed to save their * own registers if they need to: normal C functions assume they can trash the * eax register. To use normal C functions, we use * PV_CALLEE_SAVE_REGS_THUNK(), which pushes %eax onto the stack, calls the - * C function, then restores it. */ + * C function, then restores it. + */ PV_CALLEE_SAVE_REGS_THUNK(save_fl); PV_CALLEE_SAVE_REGS_THUNK(irq_disable); /*:*/ @@ -237,18 +249,20 @@ PV_CALLEE_SAVE_REGS_THUNK(irq_disable); extern void lg_irq_enable(void); extern void lg_restore_fl(unsigned long flags); -/*M:003 Note that we don't check for outstanding interrupts when we re-enable - * them (or when we unmask an interrupt). This seems to work for the moment, - * since interrupts are rare and we'll just get the interrupt on the next timer - * tick, but now we can run with CONFIG_NO_HZ, we should revisit this. One way - * would be to put the "irq_enabled" field in a page by itself, and have the - * Host write-protect it when an interrupt comes in when irqs are disabled. - * There will then be a page fault as soon as interrupts are re-enabled. +/*M:003 + * Note that we don't check for outstanding interrupts when we re-enable them + * (or when we unmask an interrupt). This seems to work for the moment, since + * interrupts are rare and we'll just get the interrupt on the next timer tick, + * but now we can run with CONFIG_NO_HZ, we should revisit this. One way would + * be to put the "irq_enabled" field in a page by itself, and have the Host + * write-protect it when an interrupt comes in when irqs are disabled. There + * will then be a page fault as soon as interrupts are re-enabled. * * A better method is to implement soft interrupt disable generally for x86: * instead of disabling interrupts, we set a flag. If an interrupt does come * in, we then disable them for real. This is uncommon, so we could simply use - * a hypercall for interrupt control and not worry about efficiency. :*/ + * a hypercall for interrupt control and not worry about efficiency. +:*/ /*G:034 * The Interrupt Descriptor Table (IDT). @@ -261,10 +275,12 @@ extern void lg_restore_fl(unsigned long flags); static void lguest_write_idt_entry(gate_desc *dt, int entrynum, const gate_desc *g) { - /* The gate_desc structure is 8 bytes long: we hand it to the Host in + /* + * The gate_desc structure is 8 bytes long: we hand it to the Host in * two 32-bit chunks. The whole 32-bit kernel used to hand descriptors * around like this; typesafety wasn't a big concern in Linux's early - * years. */ + * years. + */ u32 *desc = (u32 *)g; /* Keep the local copy up to date. */ native_write_idt_entry(dt, entrynum, g); @@ -272,9 +288,11 @@ static void lguest_write_idt_entry(gate_desc *dt, kvm_hypercall3(LHCALL_LOAD_IDT_ENTRY, entrynum, desc[0], desc[1]); } -/* Changing to a different IDT is very rare: we keep the IDT up-to-date every +/* + * Changing to a different IDT is very rare: we keep the IDT up-to-date every * time it is written, so we can simply loop through all entries and tell the - * Host about them. */ + * Host about them. + */ static void lguest_load_idt(const struct desc_ptr *desc) { unsigned int i; @@ -305,9 +323,11 @@ static void lguest_load_gdt(const struct desc_ptr *desc) kvm_hypercall3(LHCALL_LOAD_GDT_ENTRY, i, gdt[i].a, gdt[i].b); } -/* For a single GDT entry which changes, we do the lazy thing: alter our GDT, +/* + * For a single GDT entry which changes, we do the lazy thing: alter our GDT, * then tell the Host to reload the entire thing. This operation is so rare - * that this naive implementation is reasonable. */ + * that this naive implementation is reasonable. + */ static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum, const void *desc, int type) { @@ -317,29 +337,36 @@ static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum, dt[entrynum].a, dt[entrynum].b); } -/* OK, I lied. There are three "thread local storage" GDT entries which change +/* + * OK, I lied. There are three "thread local storage" GDT entries which change * on every context switch (these three entries are how glibc implements - * __thread variables). So we have a hypercall specifically for this case. */ + * __thread variables). So we have a hypercall specifically for this case. + */ static void lguest_load_tls(struct thread_struct *t, unsigned int cpu) { - /* There's one problem which normal hardware doesn't have: the Host + /* + * There's one problem which normal hardware doesn't have: the Host * can't handle us removing entries we're currently using. So we clear - * the GS register here: if it's needed it'll be reloaded anyway. */ + * the GS register here: if it's needed it'll be reloaded anyway. + */ lazy_load_gs(0); lazy_hcall2(LHCALL_LOAD_TLS, __pa(&t->tls_array), cpu); } -/*G:038 That's enough excitement for now, back to ploughing through each of - * the different pv_ops structures (we're about 1/3 of the way through). +/*G:038 + * That's enough excitement for now, back to ploughing through each of the + * different pv_ops structures (we're about 1/3 of the way through). * * This is the Local Descriptor Table, another weird Intel thingy. Linux only * uses this for some strange applications like Wine. We don't do anything - * here, so they'll get an informative and friendly Segmentation Fault. */ + * here, so they'll get an informative and friendly Segmentation Fault. + */ static void lguest_set_ldt(const void *addr, unsigned entries) { } -/* This loads a GDT entry into the "Task Register": that entry points to a +/* + * This loads a GDT entry into the "Task Register": that entry points to a * structure called the Task State Segment. Some comments scattered though the * kernel code indicate that this used for task switching in ages past, along * with blood sacrifice and astrology. @@ -347,19 +374,21 @@ static void lguest_set_ldt(const void *addr, unsigned entries) * Now there's nothing interesting in here that we don't get told elsewhere. * But the native version uses the "ltr" instruction, which makes the Host * complain to the Guest about a Segmentation Fault and it'll oops. So we - * override the native version with a do-nothing version. */ + * override the native version with a do-nothing version. + */ static void lguest_load_tr_desc(void) { } -/* The "cpuid" instruction is a way of querying both the CPU identity +/* + * The "cpuid" instruction is a way of querying both the CPU identity * (manufacturer, model, etc) and its features. It was introduced before the * Pentium in 1993 and keeps getting extended by both Intel, AMD and others. * As you might imagine, after a decade and a half this treatment, it is now a * giant ball of hair. Its entry in the current Intel manual runs to 28 pages. * * This instruction even it has its own Wikipedia entry. The Wikipedia entry - * has been translated into 4 languages. I am not making this up! + * has been translated into 5 languages. I am not making this up! * * We could get funky here and identify ourselves as "GenuineLguest", but * instead we just use the real "cpuid" instruction. Then I pretty much turned @@ -371,7 +400,8 @@ static void lguest_load_tr_desc(void) * Replacing the cpuid so we can turn features off is great for the kernel, but * anyone (including userspace) can just use the raw "cpuid" instruction and * the Host won't even notice since it isn't privileged. So we try not to get - * too worked up about it. */ + * too worked up about it. + */ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, unsigned int *cx, unsigned int *dx) { @@ -379,43 +409,63 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, native_cpuid(ax, bx, cx, dx); switch (function) { - case 0: /* ID and highest CPUID. Futureproof a little by sticking to - * older ones. */ + /* + * CPUID 0 gives the highest legal CPUID number (and the ID string). + * We futureproof our code a little by sticking to known CPUID values. + */ + case 0: if (*ax > 5) *ax = 5; break; - case 1: /* Basic feature request. */ - /* We only allow kernel to see SSE3, CMPXCHG16B and SSSE3 */ + + /* + * CPUID 1 is a basic feature request. + * + * CX: we only allow kernel to see SSE3, CMPXCHG16B and SSSE3 + * DX: SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU and PAE. + */ + case 1: *cx &= 0x00002201; - /* SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU, PAE. */ *dx &= 0x07808151; - /* The Host can do a nice optimization if it knows that the + /* + * The Host can do a nice optimization if it knows that the * kernel mappings (addresses above 0xC0000000 or whatever * PAGE_OFFSET is set to) haven't changed. But Linux calls * flush_tlb_user() for both user and kernel mappings unless - * the Page Global Enable (PGE) feature bit is set. */ + * the Page Global Enable (PGE) feature bit is set. + */ *dx |= 0x00002000; - /* We also lie, and say we're family id 5. 6 or greater + /* + * We also lie, and say we're family id 5. 6 or greater * leads to a rdmsr in early_init_intel which we can't handle. - * Family ID is returned as bits 8-12 in ax. */ + * Family ID is returned as bits 8-12 in ax. + */ *ax &= 0xFFFFF0FF; *ax |= 0x00000500; break; + /* + * 0x80000000 returns the highest Extended Function, so we futureproof + * like we do above by limiting it to known fields. + */ case 0x80000000: - /* Futureproof this a little: if they ask how much extended - * processor information there is, limit it to known fields. */ if (*ax > 0x80000008) *ax = 0x80000008; break; + + /* + * PAE systems can mark pages as non-executable. Linux calls this the + * NX bit. Intel calls it XD (eXecute Disable), AMD EVP (Enhanced + * Virus Protection). We just switch turn if off here, since we don't + * support it. + */ case 0x80000001: - /* Here we should fix nx cap depending on host. */ - /* For this version of PAE, we just clear NX bit. */ *dx &= ~(1 << 20); break; } } -/* Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4. +/* + * Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4. * I assume there's a cr1, but it hasn't bothered us yet, so we'll not bother * it. The Host needs to know when the Guest wants to change them, so we have * a whole series of functions like read_cr0() and write_cr0(). @@ -430,7 +480,8 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx, * name like "FPUTRAP bit" be a little less cryptic? * * We store cr0 locally because the Host never changes it. The Guest sometimes - * wants to read it and we'd prefer not to bother the Host unnecessarily. */ + * wants to read it and we'd prefer not to bother the Host unnecessarily. + */ static unsigned long current_cr0; static void lguest_write_cr0(unsigned long val) { @@ -443,18 +494,22 @@ static unsigned long lguest_read_cr0(void) return current_cr0; } -/* Intel provided a special instruction to clear the TS bit for people too cool +/* + * Intel provided a special instruction to clear the TS bit for people too cool * to use write_cr0() to do it. This "clts" instruction is faster, because all - * the vowels have been optimized out. */ + * the vowels have been optimized out. + */ static void lguest_clts(void) { lazy_hcall1(LHCALL_TS, 0); current_cr0 &= ~X86_CR0_TS; } -/* cr2 is the virtual address of the last page fault, which the Guest only ever +/* + * cr2 is the virtual address of the last page fault, which the Guest only ever * reads. The Host kindly writes this into our "struct lguest_data", so we - * just read it out of there. */ + * just read it out of there. + */ static unsigned long lguest_read_cr2(void) { return lguest_data.cr2; @@ -463,10 +518,12 @@ static unsigned long lguest_read_cr2(void) /* See lguest_set_pte() below. */ static bool cr3_changed = false; -/* cr3 is the current toplevel pagetable page: the principle is the same as +/* + * cr3 is the current toplevel pagetable page: the principle is the same as * cr0. Keep a local copy, and tell the Host when it changes. The only * difference is that our local copy is in lguest_data because the Host needs - * to set it upon our initial hypercall. */ + * to set it upon our initial hypercall. + */ static void lguest_write_cr3(unsigned long cr3) { lguest_data.pgdir = cr3; @@ -538,10 +595,12 @@ static void lguest_write_cr4(unsigned long val) * the real page tables based on the Guests'. */ -/* The Guest calls this to set a second-level entry (pte), ie. to map a page +/* + * The Guest calls this to set a second-level entry (pte), ie. to map a page * into a process' address space. We set the entry then tell the Host the * toplevel and address this corresponds to. The Guest uses one pagetable per - * process, so we need to tell the Host which one we're changing (mm->pgd). */ + * process, so we need to tell the Host which one we're changing (mm->pgd). + */ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { @@ -560,10 +619,13 @@ static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr, lguest_pte_update(mm, addr, ptep); } -/* The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd +/* + * The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd * to set a middle-level entry when PAE is activated. + * * Again, we set the entry then tell the Host which page we changed, - * and the index of the entry we changed. */ + * and the index of the entry we changed. + */ #ifdef CONFIG_X86_PAE static void lguest_set_pud(pud_t *pudp, pud_t pudval) { @@ -582,8 +644,7 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) } #else -/* The Guest calls lguest_set_pmd to set a top-level entry when PAE is not - * activated. */ +/* The Guest calls lguest_set_pmd to set a top-level entry when !PAE. */ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) { native_set_pmd(pmdp, pmdval); @@ -592,7 +653,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) } #endif -/* There are a couple of legacy places where the kernel sets a PTE, but we +/* + * There are a couple of legacy places where the kernel sets a PTE, but we * don't know the top level any more. This is useless for us, since we don't * know which pagetable is changing or what address, so we just tell the Host * to forget all of them. Fortunately, this is very rare. @@ -600,7 +662,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval) * ... except in early boot when the kernel sets up the initial pagetables, * which makes booting astonishingly slow: 1.83 seconds! So we don't even tell * the Host anything changed until we've done the first page table switch, - * which brings boot back to 0.25 seconds. */ + * which brings boot back to 0.25 seconds. + */ static void lguest_set_pte(pte_t *ptep, pte_t pteval) { native_set_pte(ptep, pteval); @@ -628,7 +691,8 @@ void lguest_pmd_clear(pmd_t *pmdp) } #endif -/* Unfortunately for Lguest, the pv_mmu_ops for page tables were based on +/* + * Unfortunately for Lguest, the pv_mmu_ops for page tables were based on * native page table operations. On native hardware you can set a new page * table entry whenever you want, but if you want to remove one you have to do * a TLB flush (a TLB is a little cache of page table entries kept by the CPU). @@ -637,24 +701,29 @@ void lguest_pmd_clear(pmd_t *pmdp) * called when a valid entry is written, not when it's removed (ie. marked not * present). Instead, this is where we come when the Guest wants to remove a * page table entry: we tell the Host to set that entry to 0 (ie. the present - * bit is zero). */ + * bit is zero). + */ static void lguest_flush_tlb_single(unsigned long addr) { /* Simply set it to zero: if it was not, it will fault back in. */ lazy_hcall3(LHCALL_SET_PTE, lguest_data.pgdir, addr, 0); } -/* This is what happens after the Guest has removed a large number of entries. +/* + * This is what happens after the Guest has removed a large number of entries. * This tells the Host that any of the page table entries for userspace might - * have changed, ie. virtual addresses below PAGE_OFFSET. */ + * have changed, ie. virtual addresses below PAGE_OFFSET. + */ static void lguest_flush_tlb_user(void) { lazy_hcall1(LHCALL_FLUSH_TLB, 0); } -/* This is called when the kernel page tables have changed. That's not very +/* + * This is called when the kernel page tables have changed. That's not very * common (unless the Guest is using highmem, which makes the Guest extremely - * slow), so it's worth separating this from the user flushing above. */ + * slow), so it's worth separating this from the user flushing above. + */ static void lguest_flush_tlb_kernel(void) { lazy_hcall1(LHCALL_FLUSH_TLB, 1); @@ -691,23 +760,27 @@ static struct irq_chip lguest_irq_controller = { .unmask = enable_lguest_irq, }; -/* This sets up the Interrupt Descriptor Table (IDT) entry for each hardware +/* + * This sets up the Interrupt Descriptor Table (IDT) entry for each hardware * interrupt (except 128, which is used for system calls), and then tells the * Linux infrastructure that each interrupt is controlled by our level-based - * lguest interrupt controller. */ + * lguest interrupt controller. + */ static void __init lguest_init_IRQ(void) { unsigned int i; for (i = FIRST_EXTERNAL_VECTOR; i < NR_VECTORS; i++) { - /* Some systems map "vectors" to interrupts weirdly. Lguest has - * a straightforward 1 to 1 mapping, so force that here. */ + /* Some systems map "vectors" to interrupts weirdly. Not us! */ __get_cpu_var(vector_irq)[i] = i - FIRST_EXTERNAL_VECTOR; if (i != SYSCALL_VECTOR) set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]); } - /* This call is required to set up for 4k stacks, where we have - * separate stacks for hard and soft interrupts. */ + + /* + * This call is required to set up for 4k stacks, where we have + * separate stacks for hard and soft interrupts. + */ irq_ctx_init(smp_processor_id()); } @@ -729,31 +802,39 @@ static unsigned long lguest_get_wallclock(void) return lguest_data.time.tv_sec; } -/* The TSC is an Intel thing called the Time Stamp Counter. The Host tells us +/* + * The TSC is an Intel thing called the Time Stamp Counter. The Host tells us * what speed it runs at, or 0 if it's unusable as a reliable clock source. * This matches what we want here: if we return 0 from this function, the x86 - * TSC clock will give up and not register itself. */ + * TSC clock will give up and not register itself. + */ static unsigned long lguest_tsc_khz(void) { return lguest_data.tsc_khz; } -/* If we can't use the TSC, the kernel falls back to our lower-priority - * "lguest_clock", where we read the time value given to us by the Host. */ +/* + * If we can't use the TSC, the kernel falls back to our lower-priority + * "lguest_clock", where we read the time value given to us by the Host. + */ static cycle_t lguest_clock_read(struct clocksource *cs) { unsigned long sec, nsec; - /* Since the time is in two parts (seconds and nanoseconds), we risk + /* + * Since the time is in two parts (seconds and nanoseconds), we risk * reading it just as it's changing from 99 & 0.999999999 to 100 and 0, * and getting 99 and 0. As Linux tends to come apart under the stress - * of time travel, we must be careful: */ + * of time travel, we must be careful: + */ do { /* First we read the seconds part. */ sec = lguest_data.time.tv_sec; - /* This read memory barrier tells the compiler and the CPU that + /* + * This read memory barrier tells the compiler and the CPU that * this can't be reordered: we have to complete the above - * before going on. */ + * before going on. + */ rmb(); /* Now we read the nanoseconds part. */ nsec = lguest_data.time.tv_nsec; @@ -777,9 +858,11 @@ static struct clocksource lguest_clock = { .flags = CLOCK_SOURCE_IS_CONTINUOUS, }; -/* We also need a "struct clock_event_device": Linux asks us to set it to go +/* + * We also need a "struct clock_event_device": Linux asks us to set it to go * off some time in the future. Actually, James Morris figured all this out, I - * just applied the patch. */ + * just applied the patch. + */ static int lguest_clockevent_set_next_event(unsigned long delta, struct clock_event_device *evt) { @@ -829,8 +912,10 @@ static struct clock_event_device lguest_clockevent = { .max_delta_ns = LG_CLOCK_MAX_DELTA, }; -/* This is the Guest timer interrupt handler (hardware interrupt 0). We just - * call the clockevent infrastructure and it does whatever needs doing. */ +/* + * This is the Guest timer interrupt handler (hardware interrupt 0). We just + * call the clockevent infrastructure and it does whatever needs doing. + */ static void lguest_time_irq(unsigned int irq, struct irq_desc *desc) { unsigned long flags; @@ -841,10 +926,12 @@ static void lguest_time_irq(unsigned int irq, struct irq_desc *desc) local_irq_restore(flags); } -/* At some point in the boot process, we get asked to set up our timing +/* + * At some point in the boot process, we get asked to set up our timing * infrastructure. The kernel doesn't expect timer interrupts before this, but * we cleverly initialized the "blocked_interrupts" field of "struct - * lguest_data" so that timer interrupts were blocked until now. */ + * lguest_data" so that timer interrupts were blocked until now. + */ static void lguest_time_init(void) { /* Set up the timer interrupt (0) to go to our simple timer routine */ @@ -868,14 +955,16 @@ static void lguest_time_init(void) * to work. They're pretty simple. */ -/* The Guest needs to tell the Host what stack it expects traps to use. For +/* + * The Guest needs to tell the Host what stack it expects traps to use. For * native hardware, this is part of the Task State Segment mentioned above in * lguest_load_tr_desc(), but to help hypervisors there's this special call. * * We tell the Host the segment we want to use (__KERNEL_DS is the kernel data * segment), the privilege level (we're privilege level 1, the Host is 0 and * will not tolerate us trying to use that), the stack pointer, and the number - * of pages in the stack. */ + * of pages in the stack. + */ static void lguest_load_sp0(struct tss_struct *tss, struct thread_struct *thread) { @@ -889,7 +978,8 @@ static void lguest_set_debugreg(int regno, unsigned long value) /* FIXME: Implement */ } -/* There are times when the kernel wants to make sure that no memory writes are +/* + * There are times when the kernel wants to make sure that no memory writes are * caught in the cache (that they've all reached real hardware devices). This * doesn't matter for the Guest which has virtual hardware. * @@ -903,11 +993,13 @@ static void lguest_wbinvd(void) { } -/* If the Guest expects to have an Advanced Programmable Interrupt Controller, +/* + * If the Guest expects to have an Advanced Programmable Interrupt Controller, * we play dumb by ignoring writes and returning 0 for reads. So it's no * longer Programmable nor Controlling anything, and I don't think 8 lines of * code qualifies for Advanced. It will also never interrupt anything. It - * does, however, allow us to get through the Linux boot code. */ + * does, however, allow us to get through the Linux boot code. + */ #ifdef CONFIG_X86_LOCAL_APIC static void lguest_apic_write(u32 reg, u32 v) { @@ -956,11 +1048,13 @@ static void lguest_safe_halt(void) kvm_hypercall0(LHCALL_HALT); } -/* The SHUTDOWN hypercall takes a string to describe what's happening, and +/* + * The SHUTDOWN hypercall takes a string to describe what's happening, and * an argument which says whether this to restart (reboot) the Guest or not. * * Note that the Host always prefers that the Guest speak in physical addresses - * rather than virtual addresses, so we use __pa() here. */ + * rather than virtual addresses, so we use __pa() here. + */ static void lguest_power_off(void) { kvm_hypercall2(LHCALL_SHUTDOWN, __pa("Power down"), @@ -991,8 +1085,10 @@ static __init char *lguest_memory_setup(void) * nice to move it back to lguest_init. Patch welcome... */ atomic_notifier_chain_register(&panic_notifier_list, &paniced); - /* The Linux bootloader header contains an "e820" memory map: the - * Launcher populated the first entry with our memory limit. */ + /* + *The Linux bootloader header contains an "e820" memory map: the + * Launcher populated the first entry with our memory limit. + */ e820_add_region(boot_params.e820_map[0].addr, boot_params.e820_map[0].size, boot_params.e820_map[0].type); @@ -1001,16 +1097,17 @@ static __init char *lguest_memory_setup(void) return "LGUEST"; } -/* We will eventually use the virtio console device to produce console output, +/* + * We will eventually use the virtio console device to produce console output, * but before that is set up we use LHCALL_NOTIFY on normal memory to produce - * console output. */ + * console output. + */ static __init int early_put_chars(u32 vtermno, const char *buf, int count) { char scratch[17]; unsigned int len = count; - /* We use a nul-terminated string, so we have to make a copy. Icky, - * huh? */ + /* We use a nul-terminated string, so we make a copy. Icky, huh? */ if (len > sizeof(scratch) - 1) len = sizeof(scratch) - 1; scratch[len] = '\0'; @@ -1021,8 +1118,10 @@ static __init int early_put_chars(u32 vtermno, const char *buf, int count) return len; } -/* Rebooting also tells the Host we're finished, but the RESTART flag tells the - * Launcher to reboot us. */ +/* + * Rebooting also tells the Host we're finished, but the RESTART flag tells the + * Launcher to reboot us. + */ static void lguest_restart(char *reason) { kvm_hypercall2(LHCALL_SHUTDOWN, __pa(reason), LGUEST_SHUTDOWN_RESTART); @@ -1049,7 +1148,8 @@ static void lguest_restart(char *reason) * fit comfortably. * * First we need assembly templates of each of the patchable Guest operations, - * and these are in i386_head.S. */ + * and these are in i386_head.S. + */ /*G:060 We construct a table from the assembler templates: */ static const struct lguest_insns @@ -1060,9 +1160,11 @@ static const struct lguest_insns [PARAVIRT_PATCH(pv_irq_ops.save_fl)] = { lgstart_pushf, lgend_pushf }, }; -/* Now our patch routine is fairly simple (based on the native one in +/* + * Now our patch routine is fairly simple (based on the native one in * paravirt.c). If we have a replacement, we copy it in and return how much of - * the available space we used. */ + * the available space we used. + */ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, unsigned long addr, unsigned len) { @@ -1074,8 +1176,7 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, insn_len = lguest_insns[type].end - lguest_insns[type].start; - /* Similarly if we can't fit replacement (shouldn't happen, but let's - * be thorough). */ + /* Similarly if it can't fit (doesn't happen, but let's be thorough). */ if (len < insn_len) return paravirt_patch_default(type, clobber, ibuf, addr, len); @@ -1084,22 +1185,28 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf, return insn_len; } -/*G:029 Once we get to lguest_init(), we know we're a Guest. The various +/*G:029 + * Once we get to lguest_init(), we know we're a Guest. The various * pv_ops structures in the kernel provide points for (almost) every routine we - * have to override to avoid privileged instructions. */ + * have to override to avoid privileged instructions. + */ __init void lguest_init(void) { - /* We're under lguest, paravirt is enabled, and we're running at - * privilege level 1, not 0 as normal. */ + /* We're under lguest. */ pv_info.name = "lguest"; + /* Paravirt is enabled. */ pv_info.paravirt_enabled = 1; + /* We're running at privilege level 1, not 0 as normal. */ pv_info.kernel_rpl = 1; + /* Everyone except Xen runs with this set. */ pv_info.shared_kernel_pmd = 1; - /* We set up all the lguest overrides for sensitive operations. These - * are detailed with the operations themselves. */ + /* + * We set up all the lguest overrides for sensitive operations. These + * are detailed with the operations themselves. + */ - /* interrupt-related operations */ + /* Interrupt-related operations */ pv_irq_ops.init_IRQ = lguest_init_IRQ; pv_irq_ops.save_fl = PV_CALLEE_SAVE(save_fl); pv_irq_ops.restore_fl = __PV_IS_CALLEE_SAVE(lg_restore_fl); @@ -1107,11 +1214,11 @@ __init void lguest_init(void) pv_irq_ops.irq_enable = __PV_IS_CALLEE_SAVE(lg_irq_enable); pv_irq_ops.safe_halt = lguest_safe_halt; - /* init-time operations */ + /* Setup operations */ pv_init_ops.memory_setup = lguest_memory_setup; pv_init_ops.patch = lguest_patch; - /* Intercepts of various cpu instructions */ + /* Intercepts of various CPU instructions */ pv_cpu_ops.load_gdt = lguest_load_gdt; pv_cpu_ops.cpuid = lguest_cpuid; pv_cpu_ops.load_idt = lguest_load_idt; @@ -1132,7 +1239,7 @@ __init void lguest_init(void) pv_cpu_ops.start_context_switch = paravirt_start_context_switch; pv_cpu_ops.end_context_switch = lguest_end_context_switch; - /* pagetable management */ + /* Pagetable management */ pv_mmu_ops.write_cr3 = lguest_write_cr3; pv_mmu_ops.flush_tlb_user = lguest_flush_tlb_user; pv_mmu_ops.flush_tlb_single = lguest_flush_tlb_single; @@ -1154,54 +1261,71 @@ __init void lguest_init(void) pv_mmu_ops.pte_update_defer = lguest_pte_update; #ifdef CONFIG_X86_LOCAL_APIC - /* apic read/write intercepts */ + /* APIC read/write intercepts */ set_lguest_basic_apic_ops(); #endif - /* time operations */ + /* Time operations */ pv_time_ops.get_wallclock = lguest_get_wallclock; pv_time_ops.time_init = lguest_time_init; pv_time_ops.get_tsc_khz = lguest_tsc_khz; - /* Now is a good time to look at the implementations of these functions - * before returning to the rest of lguest_init(). */ + /* + * Now is a good time to look at the implementations of these functions + * before returning to the rest of lguest_init(). + */ - /*G:070 Now we've seen all the paravirt_ops, we return to + /*G:070 + * Now we've seen all the paravirt_ops, we return to * lguest_init() where the rest of the fairly chaotic boot setup - * occurs. */ + * occurs. + */ - /* The stack protector is a weird thing where gcc places a canary + /* + * The stack protector is a weird thing where gcc places a canary * value on the stack and then checks it on return. This file is * compiled with -fno-stack-protector it, so we got this far without * problems. The value of the canary is kept at offset 20 from the * %gs register, so we need to set that up before calling C functions - * in other files. */ + * in other files. + */ setup_stack_canary_segment(0); - /* We could just call load_stack_canary_segment(), but we might as - * call switch_to_new_gdt() which loads the whole table and sets up - * the per-cpu segment descriptor register %fs as well. */ + + /* + * We could just call load_stack_canary_segment(), but we might as well + * call switch_to_new_gdt() which loads the whole table and sets up the + * per-cpu segment descriptor register %fs as well. + */ switch_to_new_gdt(0); /* As described in head_32.S, we map the first 128M of memory. */ max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT; - /* The Host<->Guest Switcher lives at the top of our address space, and + /* + * The Host<->Guest Switcher lives at the top of our address space, and * the Host told us how big it is when we made LGUEST_INIT hypercall: - * it put the answer in lguest_data.reserve_mem */ + * it put the answer in lguest_data.reserve_mem + */ reserve_top_address(lguest_data.reserve_mem); - /* If we don't initialize the lock dependency checker now, it crashes - * paravirt_disable_iospace. */ + /* + * If we don't initialize the lock dependency checker now, it crashes + * paravirt_disable_iospace. + */ lockdep_init(); - /* The IDE code spends about 3 seconds probing for disks: if we reserve + /* + * The IDE code spends about 3 seconds probing for disks: if we reserve * all the I/O ports up front it can't get them and so doesn't probe. * Other device drivers are similar (but less severe). This cuts the - * kernel boot time on my machine from 4.1 seconds to 0.45 seconds. */ + * kernel boot time on my machine from 4.1 seconds to 0.45 seconds. + */ paravirt_disable_iospace(); - /* This is messy CPU setup stuff which the native boot code does before - * start_kernel, so we have to do, too: */ + /* + * This is messy CPU setup stuff which the native boot code does before + * start_kernel, so we have to do, too: + */ cpu_detect(&new_cpu_data); /* head.S usually sets up the first capability word, so do it here. */ new_cpu_data.x86_capability[0] = cpuid_edx(1); @@ -1218,22 +1342,28 @@ __init void lguest_init(void) acpi_ht = 0; #endif - /* We set the preferred console to "hvc". This is the "hypervisor + /* + * We set the preferred console to "hvc". This is the "hypervisor * virtual console" driver written by the PowerPC people, which we also - * adapted for lguest's use. */ + * adapted for lguest's use. + */ add_preferred_console("hvc", 0, NULL); /* Register our very early console. */ virtio_cons_early_init(early_put_chars); - /* Last of all, we set the power management poweroff hook to point to + /* + * Last of all, we set the power management poweroff hook to point to * the Guest routine to power off, and the reboot hook to our restart - * routine. */ + * routine. + */ pm_power_off = lguest_power_off; machine_ops.restart = lguest_restart; - /* Now we're set up, call i386_start_kernel() in head32.c and we proceed - * to boot as normal. It never returns. */ + /* + * Now we're set up, call i386_start_kernel() in head32.c and we proceed + * to boot as normal. It never returns. + */ i386_start_kernel(); } /* diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S index a9c8cfe61cd4..db6aa95eb054 100644 --- a/arch/x86/lguest/i386_head.S +++ b/arch/x86/lguest/i386_head.S @@ -5,7 +5,8 @@ #include #include -/*G:020 Our story starts with the kernel booting into startup_32 in +/*G:020 + * Our story starts with the kernel booting into startup_32 in * arch/x86/kernel/head_32.S. It expects a boot header, which is created by * the bootloader (the Launcher in our case). * @@ -21,11 +22,14 @@ * data without remembering to subtract __PAGE_OFFSET! * * The .section line puts this code in .init.text so it will be discarded after - * boot. */ + * boot. + */ .section .init.text, "ax", @progbits ENTRY(lguest_entry) - /* We make the "initialization" hypercall now to tell the Host about - * us, and also find out where it put our page tables. */ + /* + * We make the "initialization" hypercall now to tell the Host about + * us, and also find out where it put our page tables. + */ movl $LHCALL_LGUEST_INIT, %eax movl $lguest_data - __PAGE_OFFSET, %ebx .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ @@ -33,13 +37,14 @@ ENTRY(lguest_entry) /* Set up the initial stack so we can run C code. */ movl $(init_thread_union+THREAD_SIZE),%esp - /* Jumps are relative, and we're running __PAGE_OFFSET too low at the - * moment. */ + /* Jumps are relative: we're running __PAGE_OFFSET too low. */ jmp lguest_init+__PAGE_OFFSET -/*G:055 We create a macro which puts the assembler code between lgstart_ and - * lgend_ markers. These templates are put in the .text section: they can't be - * discarded after boot as we may need to patch modules, too. */ +/*G:055 + * We create a macro which puts the assembler code between lgstart_ and lgend_ + * markers. These templates are put in the .text section: they can't be + * discarded after boot as we may need to patch modules, too. + */ .text #define LGUEST_PATCH(name, insns...) \ lgstart_##name: insns; lgend_##name:; \ @@ -48,58 +53,74 @@ ENTRY(lguest_entry) LGUEST_PATCH(cli, movl $0, lguest_data+LGUEST_DATA_irq_enabled) LGUEST_PATCH(pushf, movl lguest_data+LGUEST_DATA_irq_enabled, %eax) -/*G:033 But using those wrappers is inefficient (we'll see why that doesn't - * matter for save_fl and irq_disable later). If we write our routines - * carefully in assembler, we can avoid clobbering any registers and avoid - * jumping through the wrapper functions. +/*G:033 + * But using those wrappers is inefficient (we'll see why that doesn't matter + * for save_fl and irq_disable later). If we write our routines carefully in + * assembler, we can avoid clobbering any registers and avoid jumping through + * the wrapper functions. * * I skipped over our first piece of assembler, but this one is worth studying - * in a bit more detail so I'll describe in easy stages. First, the routine - * to enable interrupts: */ + * in a bit more detail so I'll describe in easy stages. First, the routine to + * enable interrupts: + */ ENTRY(lg_irq_enable) - /* The reverse of irq_disable, this sets lguest_data.irq_enabled to - * X86_EFLAGS_IF (ie. "Interrupts enabled"). */ + /* + * The reverse of irq_disable, this sets lguest_data.irq_enabled to + * X86_EFLAGS_IF (ie. "Interrupts enabled"). + */ movl $X86_EFLAGS_IF, lguest_data+LGUEST_DATA_irq_enabled - /* But now we need to check if the Host wants to know: there might have + /* + * But now we need to check if the Host wants to know: there might have * been interrupts waiting to be delivered, in which case it will have * set lguest_data.irq_pending to X86_EFLAGS_IF. If it's not zero, we - * jump to send_interrupts, otherwise we're done. */ + * jump to send_interrupts, otherwise we're done. + */ testl $0, lguest_data+LGUEST_DATA_irq_pending jnz send_interrupts - /* One cool thing about x86 is that you can do many things without using + /* + * One cool thing about x86 is that you can do many things without using * a register. In this case, the normal path hasn't needed to save or - * restore any registers at all! */ + * restore any registers at all! + */ ret send_interrupts: - /* OK, now we need a register: eax is used for the hypercall number, + /* + * OK, now we need a register: eax is used for the hypercall number, * which is LHCALL_SEND_INTERRUPTS. * * We used not to bother with this pending detection at all, which was * much simpler. Sooner or later the Host would realize it had to * send us an interrupt. But that turns out to make performance 7 * times worse on a simple tcp benchmark. So now we do this the hard - * way. */ + * way. + */ pushl %eax movl $LHCALL_SEND_INTERRUPTS, %eax - /* This is a vmcall instruction (same thing that KVM uses). Older + /* + * This is a vmcall instruction (same thing that KVM uses). Older * assembler versions might not know the "vmcall" instruction, so we - * create one manually here. */ + * create one manually here. + */ .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ popl %eax ret -/* Finally, the "popf" or "restore flags" routine. The %eax register holds the +/* + * Finally, the "popf" or "restore flags" routine. The %eax register holds the * flags (in practice, either X86_EFLAGS_IF or 0): if it's X86_EFLAGS_IF we're - * enabling interrupts again, if it's 0 we're leaving them off. */ + * enabling interrupts again, if it's 0 we're leaving them off. + */ ENTRY(lg_restore_fl) /* This is just "lguest_data.irq_enabled = flags;" */ movl %eax, lguest_data+LGUEST_DATA_irq_enabled - /* Now, if the %eax value has enabled interrupts and + /* + * Now, if the %eax value has enabled interrupts and * lguest_data.irq_pending is set, we want to tell the Host so it can * deliver any outstanding interrupts. Fortunately, both values will * be X86_EFLAGS_IF (ie. 512) in that case, and the "testl" * instruction will AND them together for us. If both are set, we - * jump to send_interrupts. */ + * jump to send_interrupts. + */ testl lguest_data+LGUEST_DATA_irq_pending, %eax jnz send_interrupts /* Again, the normal path has used no extra registers. Clever, huh? */ @@ -109,22 +130,24 @@ ENTRY(lg_restore_fl) .global lguest_noirq_start .global lguest_noirq_end -/*M:004 When the Host reflects a trap or injects an interrupt into the Guest, - * it sets the eflags interrupt bit on the stack based on - * lguest_data.irq_enabled, so the Guest iret logic does the right thing when - * restoring it. However, when the Host sets the Guest up for direct traps, - * such as system calls, the processor is the one to push eflags onto the - * stack, and the interrupt bit will be 1 (in reality, interrupts are always - * enabled in the Guest). +/*M:004 + * When the Host reflects a trap or injects an interrupt into the Guest, it + * sets the eflags interrupt bit on the stack based on lguest_data.irq_enabled, + * so the Guest iret logic does the right thing when restoring it. However, + * when the Host sets the Guest up for direct traps, such as system calls, the + * processor is the one to push eflags onto the stack, and the interrupt bit + * will be 1 (in reality, interrupts are always enabled in the Guest). * * This turns out to be harmless: the only trap which should happen under Linux * with interrupts disabled is Page Fault (due to our lazy mapping of vmalloc * regions), which has to be reflected through the Host anyway. If another * trap *does* go off when interrupts are disabled, the Guest will panic, and - * we'll never get to this iret! :*/ + * we'll never get to this iret! +:*/ -/*G:045 There is one final paravirt_op that the Guest implements, and glancing - * at it you can see why I left it to last. It's *cool*! It's in *assembler*! +/*G:045 + * There is one final paravirt_op that the Guest implements, and glancing at it + * you can see why I left it to last. It's *cool*! It's in *assembler*! * * The "iret" instruction is used to return from an interrupt or trap. The * stack looks like this: @@ -148,15 +171,18 @@ ENTRY(lg_restore_fl) * return to userspace or wherever. Our solution to this is to surround the * code with lguest_noirq_start: and lguest_noirq_end: labels. We tell the * Host that it is *never* to interrupt us there, even if interrupts seem to be - * enabled. */ + * enabled. + */ ENTRY(lguest_iret) pushl %eax movl 12(%esp), %eax lguest_noirq_start: - /* Note the %ss: segment prefix here. Normal data accesses use the + /* + * Note the %ss: segment prefix here. Normal data accesses use the * "ds" segment, but that will have already been restored for whatever * we're returning to (such as userspace): we can't trust it. The %ss: - * prefix makes sure we use the stack segment, which is still valid. */ + * prefix makes sure we use the stack segment, which is still valid. + */ movl %eax,%ss:lguest_data+LGUEST_DATA_irq_enabled popl %eax iret diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c index a6974e9b8ebf..cd058bc903ff 100644 --- a/drivers/lguest/core.c +++ b/drivers/lguest/core.c @@ -1,6 +1,8 @@ -/*P:400 This contains run_guest() which actually calls into the Host<->Guest +/*P:400 + * This contains run_guest() which actually calls into the Host<->Guest * Switcher and analyzes the return, such as determining if the Guest wants the - * Host to do something. This file also contains useful helper routines. :*/ + * Host to do something. This file also contains useful helper routines. +:*/ #include #include #include @@ -24,7 +26,8 @@ static struct page **switcher_page; /* This One Big lock protects all inter-guest data structures. */ DEFINE_MUTEX(lguest_lock); -/*H:010 We need to set up the Switcher at a high virtual address. Remember the +/*H:010 + * We need to set up the Switcher at a high virtual address. Remember the * Switcher is a few hundred bytes of assembler code which actually changes the * CPU to run the Guest, and then changes back to the Host when a trap or * interrupt happens. @@ -33,7 +36,8 @@ DEFINE_MUTEX(lguest_lock); * Host since it will be running as the switchover occurs. * * Trying to map memory at a particular address is an unusual thing to do, so - * it's not a simple one-liner. */ + * it's not a simple one-liner. + */ static __init int map_switcher(void) { int i, err; @@ -47,8 +51,10 @@ static __init int map_switcher(void) * easy. */ - /* We allocate an array of struct page pointers. map_vm_area() wants - * this, rather than just an array of pages. */ + /* + * We allocate an array of struct page pointers. map_vm_area() wants + * this, rather than just an array of pages. + */ switcher_page = kmalloc(sizeof(switcher_page[0])*TOTAL_SWITCHER_PAGES, GFP_KERNEL); if (!switcher_page) { @@ -56,8 +62,10 @@ static __init int map_switcher(void) goto out; } - /* Now we actually allocate the pages. The Guest will see these pages, - * so we make sure they're zeroed. */ + /* + * Now we actually allocate the pages. The Guest will see these pages, + * so we make sure they're zeroed. + */ for (i = 0; i < TOTAL_SWITCHER_PAGES; i++) { unsigned long addr = get_zeroed_page(GFP_KERNEL); if (!addr) { @@ -67,19 +75,23 @@ static __init int map_switcher(void) switcher_page[i] = virt_to_page(addr); } - /* First we check that the Switcher won't overlap the fixmap area at + /* + * First we check that the Switcher won't overlap the fixmap area at * the top of memory. It's currently nowhere near, but it could have - * very strange effects if it ever happened. */ + * very strange effects if it ever happened. + */ if (SWITCHER_ADDR + (TOTAL_SWITCHER_PAGES+1)*PAGE_SIZE > FIXADDR_START){ err = -ENOMEM; printk("lguest: mapping switcher would thwack fixmap\n"); goto free_pages; } - /* Now we reserve the "virtual memory area" we want: 0xFFC00000 + /* + * Now we reserve the "virtual memory area" we want: 0xFFC00000 * (SWITCHER_ADDR). We might not get it in theory, but in practice * it's worked so far. The end address needs +1 because __get_vm_area - * allocates an extra guard page, so we need space for that. */ + * allocates an extra guard page, so we need space for that. + */ switcher_vma = __get_vm_area(TOTAL_SWITCHER_PAGES * PAGE_SIZE, VM_ALLOC, SWITCHER_ADDR, SWITCHER_ADDR + (TOTAL_SWITCHER_PAGES+1) * PAGE_SIZE); @@ -89,11 +101,13 @@ static __init int map_switcher(void) goto free_pages; } - /* This code actually sets up the pages we've allocated to appear at + /* + * This code actually sets up the pages we've allocated to appear at * SWITCHER_ADDR. map_vm_area() takes the vma we allocated above, the * kind of pages we're mapping (kernel pages), and a pointer to our * array of struct pages. It increments that pointer, but we don't - * care. */ + * care. + */ pagep = switcher_page; err = map_vm_area(switcher_vma, PAGE_KERNEL_EXEC, &pagep); if (err) { @@ -101,8 +115,10 @@ static __init int map_switcher(void) goto free_vma; } - /* Now the Switcher is mapped at the right address, we can't fail! - * Copy in the compiled-in Switcher code (from _switcher.S). */ + /* + * Now the Switcher is mapped at the right address, we can't fail! + * Copy in the compiled-in Switcher code (from _switcher.S). + */ memcpy(switcher_vma->addr, start_switcher_text, end_switcher_text - start_switcher_text); @@ -124,8 +140,7 @@ out: } /*:*/ -/* Cleaning up the mapping when the module is unloaded is almost... - * too easy. */ +/* Cleaning up the mapping when the module is unloaded is almost... too easy. */ static void unmap_switcher(void) { unsigned int i; @@ -151,16 +166,19 @@ static void unmap_switcher(void) * But we can't trust the Guest: it might be trying to access the Launcher * code. We have to check that the range is below the pfn_limit the Launcher * gave us. We have to make sure that addr + len doesn't give us a false - * positive by overflowing, too. */ + * positive by overflowing, too. + */ bool lguest_address_ok(const struct lguest *lg, unsigned long addr, unsigned long len) { return (addr+len) / PAGE_SIZE < lg->pfn_limit && (addr+len >= addr); } -/* This routine copies memory from the Guest. Here we can see how useful the +/* + * This routine copies memory from the Guest. Here we can see how useful the * kill_lguest() routine we met in the Launcher can be: we return a random - * value (all zeroes) instead of needing to return an error. */ + * value (all zeroes) instead of needing to return an error. + */ void __lgread(struct lg_cpu *cpu, void *b, unsigned long addr, unsigned bytes) { if (!lguest_address_ok(cpu->lg, addr, bytes) @@ -181,9 +199,11 @@ void __lgwrite(struct lg_cpu *cpu, unsigned long addr, const void *b, } /*:*/ -/*H:030 Let's jump straight to the the main loop which runs the Guest. +/*H:030 + * Let's jump straight to the the main loop which runs the Guest. * Remember, this is called by the Launcher reading /dev/lguest, and we keep - * going around and around until something interesting happens. */ + * going around and around until something interesting happens. + */ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) { /* We stop running once the Guest is dead. */ @@ -195,8 +215,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) if (cpu->hcall) do_hypercalls(cpu); - /* It's possible the Guest did a NOTIFY hypercall to the - * Launcher, in which case we return from the read() now. */ + /* + * It's possible the Guest did a NOTIFY hypercall to the + * Launcher, in which case we return from the read() now. + */ if (cpu->pending_notify) { if (!send_notify_to_eventfd(cpu)) { if (put_user(cpu->pending_notify, user)) @@ -209,29 +231,39 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) if (signal_pending(current)) return -ERESTARTSYS; - /* Check if there are any interrupts which can be delivered now: + /* + * Check if there are any interrupts which can be delivered now: * if so, this sets up the hander to be executed when we next - * run the Guest. */ + * run the Guest. + */ irq = interrupt_pending(cpu, &more); if (irq < LGUEST_IRQS) try_deliver_interrupt(cpu, irq, more); - /* All long-lived kernel loops need to check with this horrible + /* + * All long-lived kernel loops need to check with this horrible * thing called the freezer. If the Host is trying to suspend, - * it stops us. */ + * it stops us. + */ try_to_freeze(); - /* Just make absolutely sure the Guest is still alive. One of - * those hypercalls could have been fatal, for example. */ + /* + * Just make absolutely sure the Guest is still alive. One of + * those hypercalls could have been fatal, for example. + */ if (cpu->lg->dead) break; - /* If the Guest asked to be stopped, we sleep. The Guest's - * clock timer will wake us. */ + /* + * If the Guest asked to be stopped, we sleep. The Guest's + * clock timer will wake us. + */ if (cpu->halted) { set_current_state(TASK_INTERRUPTIBLE); - /* Just before we sleep, make sure no interrupt snuck in - * which we should be doing. */ + /* + * Just before we sleep, make sure no interrupt snuck in + * which we should be doing. + */ if (interrupt_pending(cpu, &more) < LGUEST_IRQS) set_current_state(TASK_RUNNING); else @@ -239,8 +271,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) continue; } - /* OK, now we're ready to jump into the Guest. First we put up - * the "Do Not Disturb" sign: */ + /* + * OK, now we're ready to jump into the Guest. First we put up + * the "Do Not Disturb" sign: + */ local_irq_disable(); /* Actually run the Guest until something happens. */ @@ -327,8 +361,10 @@ static void __exit fini(void) } /*:*/ -/* The Host side of lguest can be a module. This is a nice way for people to - * play with it. */ +/* + * The Host side of lguest can be a module. This is a nice way for people to + * play with it. + */ module_init(init); module_exit(fini); MODULE_LICENSE("GPL"); diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c index c29ffa19cb74..787ab4bc09f0 100644 --- a/drivers/lguest/hypercalls.c +++ b/drivers/lguest/hypercalls.c @@ -1,8 +1,10 @@ -/*P:500 Just as userspace programs request kernel operations through a system +/*P:500 + * Just as userspace programs request kernel operations through a system * call, the Guest requests Host operations through a "hypercall". You might * notice this nomenclature doesn't really follow any logic, but the name has * been around for long enough that we're stuck with it. As you'd expect, this - * code is basically a one big switch statement. :*/ + * code is basically a one big switch statement. +:*/ /* Copyright (C) 2006 Rusty Russell IBM Corporation @@ -28,30 +30,41 @@ #include #include "lg.h" -/*H:120 This is the core hypercall routine: where the Guest gets what it wants. - * Or gets killed. Or, in the case of LHCALL_SHUTDOWN, both. */ +/*H:120 + * This is the core hypercall routine: where the Guest gets what it wants. + * Or gets killed. Or, in the case of LHCALL_SHUTDOWN, both. + */ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) { switch (args->arg0) { case LHCALL_FLUSH_ASYNC: - /* This call does nothing, except by breaking out of the Guest - * it makes us process all the asynchronous hypercalls. */ + /* + * This call does nothing, except by breaking out of the Guest + * it makes us process all the asynchronous hypercalls. + */ break; case LHCALL_SEND_INTERRUPTS: - /* This call does nothing too, but by breaking out of the Guest - * it makes us process any pending interrupts. */ + /* + * This call does nothing too, but by breaking out of the Guest + * it makes us process any pending interrupts. + */ break; case LHCALL_LGUEST_INIT: - /* You can't get here unless you're already initialized. Don't - * do that. */ + /* + * You can't get here unless you're already initialized. Don't + * do that. + */ kill_guest(cpu, "already have lguest_data"); break; case LHCALL_SHUTDOWN: { - /* Shutdown is such a trivial hypercall that we do it in four - * lines right here. */ char msg[128]; - /* If the lgread fails, it will call kill_guest() itself; the - * kill_guest() with the message will be ignored. */ + /* + * Shutdown is such a trivial hypercall that we do it in four + * lines right here. + * + * If the lgread fails, it will call kill_guest() itself; the + * kill_guest() with the message will be ignored. + */ __lgread(cpu, msg, args->arg1, sizeof(msg)); msg[sizeof(msg)-1] = '\0'; kill_guest(cpu, "CRASH: %s", msg); @@ -60,16 +73,17 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) break; } case LHCALL_FLUSH_TLB: - /* FLUSH_TLB comes in two flavors, depending on the - * argument: */ + /* FLUSH_TLB comes in two flavors, depending on the argument: */ if (args->arg1) guest_pagetable_clear_all(cpu); else guest_pagetable_flush_user(cpu); break; - /* All these calls simply pass the arguments through to the right - * routines. */ + /* + * All these calls simply pass the arguments through to the right + * routines. + */ case LHCALL_NEW_PGTABLE: guest_new_pagetable(cpu, args->arg1); break; @@ -112,15 +126,16 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) kill_guest(cpu, "Bad hypercall %li\n", args->arg0); } } -/*:*/ -/*H:124 Asynchronous hypercalls are easy: we just look in the array in the +/*H:124 + * Asynchronous hypercalls are easy: we just look in the array in the * Guest's "struct lguest_data" to see if any new ones are marked "ready". * * We are careful to do these in order: obviously we respect the order the * Guest put them in the ring, but we also promise the Guest that they will * happen before any normal hypercall (which is why we check this before - * checking for a normal hcall). */ + * checking for a normal hcall). + */ static void do_async_hcalls(struct lg_cpu *cpu) { unsigned int i; @@ -133,22 +148,28 @@ static void do_async_hcalls(struct lg_cpu *cpu) /* We process "struct lguest_data"s hcalls[] ring once. */ for (i = 0; i < ARRAY_SIZE(st); i++) { struct hcall_args args; - /* We remember where we were up to from last time. This makes + /* + * We remember where we were up to from last time. This makes * sure that the hypercalls are done in the order the Guest - * places them in the ring. */ + * places them in the ring. + */ unsigned int n = cpu->next_hcall; /* 0xFF means there's no call here (yet). */ if (st[n] == 0xFF) break; - /* OK, we have hypercall. Increment the "next_hcall" cursor, - * and wrap back to 0 if we reach the end. */ + /* + * OK, we have hypercall. Increment the "next_hcall" cursor, + * and wrap back to 0 if we reach the end. + */ if (++cpu->next_hcall == LHCALL_RING_SIZE) cpu->next_hcall = 0; - /* Copy the hypercall arguments into a local copy of - * the hcall_args struct. */ + /* + * Copy the hypercall arguments into a local copy of the + * hcall_args struct. + */ if (copy_from_user(&args, &cpu->lg->lguest_data->hcalls[n], sizeof(struct hcall_args))) { kill_guest(cpu, "Fetching async hypercalls"); @@ -164,19 +185,25 @@ static void do_async_hcalls(struct lg_cpu *cpu) break; } - /* Stop doing hypercalls if they want to notify the Launcher: - * it needs to service this first. */ + /* + * Stop doing hypercalls if they want to notify the Launcher: + * it needs to service this first. + */ if (cpu->pending_notify) break; } } -/* Last of all, we look at what happens first of all. The very first time the - * Guest makes a hypercall, we end up here to set things up: */ +/* + * Last of all, we look at what happens first of all. The very first time the + * Guest makes a hypercall, we end up here to set things up: + */ static void initialize(struct lg_cpu *cpu) { - /* You can't do anything until you're initialized. The Guest knows the - * rules, so we're unforgiving here. */ + /* + * You can't do anything until you're initialized. The Guest knows the + * rules, so we're unforgiving here. + */ if (cpu->hcall->arg0 != LHCALL_LGUEST_INIT) { kill_guest(cpu, "hypercall %li before INIT", cpu->hcall->arg0); return; @@ -185,32 +212,40 @@ static void initialize(struct lg_cpu *cpu) if (lguest_arch_init_hypercalls(cpu)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* The Guest tells us where we're not to deliver interrupts by putting - * the range of addresses into "struct lguest_data". */ + /* + * The Guest tells us where we're not to deliver interrupts by putting + * the range of addresses into "struct lguest_data". + */ if (get_user(cpu->lg->noirq_start, &cpu->lg->lguest_data->noirq_start) || get_user(cpu->lg->noirq_end, &cpu->lg->lguest_data->noirq_end)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* We write the current time into the Guest's data page once so it can - * set its clock. */ + /* + * We write the current time into the Guest's data page once so it can + * set its clock. + */ write_timestamp(cpu); /* page_tables.c will also do some setup. */ page_table_guest_data_init(cpu); - /* This is the one case where the above accesses might have been the + /* + * This is the one case where the above accesses might have been the * first write to a Guest page. This may have caused a copy-on-write * fault, but the old page might be (read-only) in the Guest - * pagetable. */ + * pagetable. + */ guest_pagetable_clear_all(cpu); } /*:*/ -/*M:013 If a Guest reads from a page (so creates a mapping) that it has never +/*M:013 + * If a Guest reads from a page (so creates a mapping) that it has never * written to, and then the Launcher writes to it (ie. the output of a virtual * device), the Guest will still see the old page. In practice, this never * happens: why would the Guest read a page which it has never written to? But - * a similar scenario might one day bite us, so it's worth mentioning. :*/ + * a similar scenario might one day bite us, so it's worth mentioning. +:*/ /*H:100 * Hypercalls @@ -229,17 +264,22 @@ void do_hypercalls(struct lg_cpu *cpu) return; } - /* The Guest has initialized. + /* + * The Guest has initialized. * - * Look in the hypercall ring for the async hypercalls: */ + * Look in the hypercall ring for the async hypercalls: + */ do_async_hcalls(cpu); - /* If we stopped reading the hypercall ring because the Guest did a + /* + * If we stopped reading the hypercall ring because the Guest did a * NOTIFY to the Launcher, we want to return now. Otherwise we do - * the hypercall. */ + * the hypercall. + */ if (!cpu->pending_notify) { do_hcall(cpu, cpu->hcall); - /* Tricky point: we reset the hcall pointer to mark the + /* + * Tricky point: we reset the hcall pointer to mark the * hypercall as "done". We use the hcall pointer rather than * the trap number to indicate a hypercall is pending. * Normally it doesn't matter: the Guest will run again and @@ -248,13 +288,16 @@ void do_hypercalls(struct lg_cpu *cpu) * However, if we are signalled or the Guest sends I/O to the * Launcher, the run_guest() loop will exit without running the * Guest. When it comes back it would try to re-run the - * hypercall. Finding that bug sucked. */ + * hypercall. Finding that bug sucked. + */ cpu->hcall = NULL; } } -/* This routine supplies the Guest with time: it's used for wallclock time at - * initial boot and as a rough time source if the TSC isn't available. */ +/* + * This routine supplies the Guest with time: it's used for wallclock time at + * initial boot and as a rough time source if the TSC isn't available. + */ void write_timestamp(struct lg_cpu *cpu) { struct timespec now; diff --git a/drivers/lguest/interrupts_and_traps.c b/drivers/lguest/interrupts_and_traps.c index 0e9067b0d507..18648180db02 100644 --- a/drivers/lguest/interrupts_and_traps.c +++ b/drivers/lguest/interrupts_and_traps.c @@ -1,4 +1,5 @@ -/*P:800 Interrupts (traps) are complicated enough to earn their own file. +/*P:800 + * Interrupts (traps) are complicated enough to earn their own file. * There are three classes of interrupts: * * 1) Real hardware interrupts which occur while we're running the Guest, @@ -10,7 +11,8 @@ * just like real hardware would deliver them. Traps from the Guest can be set * up to go directly back into the Guest, but sometimes the Host wants to see * them first, so we also have a way of "reflecting" them into the Guest as if - * they had been delivered to it directly. :*/ + * they had been delivered to it directly. +:*/ #include #include #include @@ -26,8 +28,10 @@ static unsigned long idt_address(u32 lo, u32 hi) return (lo & 0x0000FFFF) | (hi & 0xFFFF0000); } -/* The "type" of the interrupt handler is a 4 bit field: we only support a - * couple of types. */ +/* + * The "type" of the interrupt handler is a 4 bit field: we only support a + * couple of types. + */ static int idt_type(u32 lo, u32 hi) { return (hi >> 8) & 0xF; @@ -39,8 +43,10 @@ static bool idt_present(u32 lo, u32 hi) return (hi & 0x8000); } -/* We need a helper to "push" a value onto the Guest's stack, since that's a - * big part of what delivering an interrupt does. */ +/* + * We need a helper to "push" a value onto the Guest's stack, since that's a + * big part of what delivering an interrupt does. + */ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) { /* Stack grows upwards: move stack then write value. */ @@ -48,7 +54,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) lgwrite(cpu, *gstack, u32, val); } -/*H:210 The set_guest_interrupt() routine actually delivers the interrupt or +/*H:210 + * The set_guest_interrupt() routine actually delivers the interrupt or * trap. The mechanics of delivering traps and interrupts to the Guest are the * same, except some traps have an "error code" which gets pushed onto the * stack as well: the caller tells us if this is one. @@ -59,7 +66,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val) * * We set up the stack just like the CPU does for a real interrupt, so it's * identical for the Guest (and the standard "iret" instruction will undo - * it). */ + * it). + */ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, bool has_err) { @@ -67,20 +75,26 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, u32 eflags, ss, irq_enable; unsigned long virtstack; - /* There are two cases for interrupts: one where the Guest is already + /* + * There are two cases for interrupts: one where the Guest is already * in the kernel, and a more complex one where the Guest is in - * userspace. We check the privilege level to find out. */ + * userspace. We check the privilege level to find out. + */ if ((cpu->regs->ss&0x3) != GUEST_PL) { - /* The Guest told us their kernel stack with the SET_STACK - * hypercall: both the virtual address and the segment */ + /* + * The Guest told us their kernel stack with the SET_STACK + * hypercall: both the virtual address and the segment. + */ virtstack = cpu->esp1; ss = cpu->ss1; origstack = gstack = guest_pa(cpu, virtstack); - /* We push the old stack segment and pointer onto the new + /* + * We push the old stack segment and pointer onto the new * stack: when the Guest does an "iret" back from the interrupt * handler the CPU will notice they're dropping privilege - * levels and expect these here. */ + * levels and expect these here. + */ push_guest_stack(cpu, &gstack, cpu->regs->ss); push_guest_stack(cpu, &gstack, cpu->regs->esp); } else { @@ -91,18 +105,22 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, origstack = gstack = guest_pa(cpu, virtstack); } - /* Remember that we never let the Guest actually disable interrupts, so + /* + * Remember that we never let the Guest actually disable interrupts, so * the "Interrupt Flag" bit is always set. We copy that bit from the * Guest's "irq_enabled" field into the eflags word: we saw the Guest - * copy it back in "lguest_iret". */ + * copy it back in "lguest_iret". + */ eflags = cpu->regs->eflags; if (get_user(irq_enable, &cpu->lg->lguest_data->irq_enabled) == 0 && !(irq_enable & X86_EFLAGS_IF)) eflags &= ~X86_EFLAGS_IF; - /* An interrupt is expected to push three things on the stack: the old + /* + * An interrupt is expected to push three things on the stack: the old * "eflags" word, the old code segment, and the old instruction - * pointer. */ + * pointer. + */ push_guest_stack(cpu, &gstack, eflags); push_guest_stack(cpu, &gstack, cpu->regs->cs); push_guest_stack(cpu, &gstack, cpu->regs->eip); @@ -111,15 +129,19 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, if (has_err) push_guest_stack(cpu, &gstack, cpu->regs->errcode); - /* Now we've pushed all the old state, we change the stack, the code - * segment and the address to execute. */ + /* + * Now we've pushed all the old state, we change the stack, the code + * segment and the address to execute. + */ cpu->regs->ss = ss; cpu->regs->esp = virtstack + (gstack - origstack); cpu->regs->cs = (__KERNEL_CS|GUEST_PL); cpu->regs->eip = idt_address(lo, hi); - /* There are two kinds of interrupt handlers: 0xE is an "interrupt - * gate" which expects interrupts to be disabled on entry. */ + /* + * There are two kinds of interrupt handlers: 0xE is an "interrupt + * gate" which expects interrupts to be disabled on entry. + */ if (idt_type(lo, hi) == 0xE) if (put_user(0, &cpu->lg->lguest_data->irq_enabled)) kill_guest(cpu, "Disabling interrupts"); @@ -130,7 +152,8 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi, * * interrupt_pending() returns the first pending interrupt which isn't blocked * by the Guest. It is called before every entry to the Guest, and just before - * we go to sleep when the Guest has halted itself. */ + * we go to sleep when the Guest has halted itself. + */ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) { unsigned int irq; @@ -140,8 +163,10 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) if (!cpu->lg->lguest_data) return LGUEST_IRQS; - /* Take our "irqs_pending" array and remove any interrupts the Guest - * wants blocked: the result ends up in "blk". */ + /* + * Take our "irqs_pending" array and remove any interrupts the Guest + * wants blocked: the result ends up in "blk". + */ if (copy_from_user(&blk, cpu->lg->lguest_data->blocked_interrupts, sizeof(blk))) return LGUEST_IRQS; @@ -154,16 +179,20 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more) return irq; } -/* This actually diverts the Guest to running an interrupt handler, once an - * interrupt has been identified by interrupt_pending(). */ +/* + * This actually diverts the Guest to running an interrupt handler, once an + * interrupt has been identified by interrupt_pending(). + */ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) { struct desc_struct *idt; BUG_ON(irq >= LGUEST_IRQS); - /* They may be in the middle of an iret, where they asked us never to - * deliver interrupts. */ + /* + * They may be in the middle of an iret, where they asked us never to + * deliver interrupts. + */ if (cpu->regs->eip >= cpu->lg->noirq_start && (cpu->regs->eip < cpu->lg->noirq_end)) return; @@ -187,29 +216,37 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) } } - /* Look at the IDT entry the Guest gave us for this interrupt. The + /* + * Look at the IDT entry the Guest gave us for this interrupt. The * first 32 (FIRST_EXTERNAL_VECTOR) entries are for traps, so we skip - * over them. */ + * over them. + */ idt = &cpu->arch.idt[FIRST_EXTERNAL_VECTOR+irq]; /* If they don't have a handler (yet?), we just ignore it */ if (idt_present(idt->a, idt->b)) { /* OK, mark it no longer pending and deliver it. */ clear_bit(irq, cpu->irqs_pending); - /* set_guest_interrupt() takes the interrupt descriptor and a + /* + * set_guest_interrupt() takes the interrupt descriptor and a * flag to say whether this interrupt pushes an error code onto - * the stack as well: virtual interrupts never do. */ + * the stack as well: virtual interrupts never do. + */ set_guest_interrupt(cpu, idt->a, idt->b, false); } - /* Every time we deliver an interrupt, we update the timestamp in the + /* + * Every time we deliver an interrupt, we update the timestamp in the * Guest's lguest_data struct. It would be better for the Guest if we * did this more often, but it can actually be quite slow: doing it * here is a compromise which means at least it gets updated every - * timer interrupt. */ + * timer interrupt. + */ write_timestamp(cpu); - /* If there are no other interrupts we want to deliver, clear - * the pending flag. */ + /* + * If there are no other interrupts we want to deliver, clear + * the pending flag. + */ if (!more) put_user(0, &cpu->lg->lguest_data->irq_pending); } @@ -217,24 +254,29 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more) /* And this is the routine when we want to set an interrupt for the Guest. */ void set_interrupt(struct lg_cpu *cpu, unsigned int irq) { - /* Next time the Guest runs, the core code will see if it can deliver - * this interrupt. */ + /* + * Next time the Guest runs, the core code will see if it can deliver + * this interrupt. + */ set_bit(irq, cpu->irqs_pending); - /* Make sure it sees it; it might be asleep (eg. halted), or - * running the Guest right now, in which case kick_process() - * will knock it out. */ + /* + * Make sure it sees it; it might be asleep (eg. halted), or running + * the Guest right now, in which case kick_process() will knock it out. + */ if (!wake_up_process(cpu->tsk)) kick_process(cpu->tsk); } /*:*/ -/* Linux uses trap 128 for system calls. Plan9 uses 64, and Ron Minnich sent +/* + * Linux uses trap 128 for system calls. Plan9 uses 64, and Ron Minnich sent * me a patch, so we support that too. It'd be a big step for lguest if half * the Plan 9 user base were to start using it. * * Actually now I think of it, it's possible that Ron *is* half the Plan 9 - * userbase. Oh well. */ + * userbase. Oh well. + */ static bool could_be_syscall(unsigned int num) { /* Normal Linux SYSCALL_VECTOR or reserved vector? */ @@ -274,9 +316,11 @@ void free_interrupts(void) clear_bit(syscall_vector, used_vectors); } -/*H:220 Now we've got the routines to deliver interrupts, delivering traps like +/*H:220 + * Now we've got the routines to deliver interrupts, delivering traps like * page fault is easy. The only trick is that Intel decided that some traps - * should have error codes: */ + * should have error codes: + */ static bool has_err(unsigned int trap) { return (trap == 8 || (trap >= 10 && trap <= 14) || trap == 17); @@ -285,13 +329,17 @@ static bool has_err(unsigned int trap) /* deliver_trap() returns true if it could deliver the trap. */ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) { - /* Trap numbers are always 8 bit, but we set an impossible trap number - * for traps inside the Switcher, so check that here. */ + /* + * Trap numbers are always 8 bit, but we set an impossible trap number + * for traps inside the Switcher, so check that here. + */ if (num >= ARRAY_SIZE(cpu->arch.idt)) return false; - /* Early on the Guest hasn't set the IDT entries (or maybe it put a - * bogus one in): if we fail here, the Guest will be killed. */ + /* + * Early on the Guest hasn't set the IDT entries (or maybe it put a + * bogus one in): if we fail here, the Guest will be killed. + */ if (!idt_present(cpu->arch.idt[num].a, cpu->arch.idt[num].b)) return false; set_guest_interrupt(cpu, cpu->arch.idt[num].a, @@ -299,7 +347,8 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) return true; } -/*H:250 Here's the hard part: returning to the Host every time a trap happens +/*H:250 + * Here's the hard part: returning to the Host every time a trap happens * and then calling deliver_trap() and re-entering the Guest is slow. * Particularly because Guest userspace system calls are traps (usually trap * 128). @@ -311,69 +360,87 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num) * the other hypervisors would beat it up at lunchtime. * * This routine indicates if a particular trap number could be delivered - * directly. */ + * directly. + */ static bool direct_trap(unsigned int num) { - /* Hardware interrupts don't go to the Guest at all (except system - * call). */ + /* + * Hardware interrupts don't go to the Guest at all (except system + * call). + */ if (num >= FIRST_EXTERNAL_VECTOR && !could_be_syscall(num)) return false; - /* The Host needs to see page faults (for shadow paging and to save the + /* + * The Host needs to see page faults (for shadow paging and to save the * fault address), general protection faults (in/out emulation) and * device not available (TS handling), invalid opcode fault (kvm hcall), - * and of course, the hypercall trap. */ + * and of course, the hypercall trap. + */ return num != 14 && num != 13 && num != 7 && num != 6 && num != LGUEST_TRAP_ENTRY; } /*:*/ -/*M:005 The Guest has the ability to turn its interrupt gates into trap gates, +/*M:005 + * The Guest has the ability to turn its interrupt gates into trap gates, * if it is careful. The Host will let trap gates can go directly to the * Guest, but the Guest needs the interrupts atomically disabled for an * interrupt gate. It can do this by pointing the trap gate at instructions - * within noirq_start and noirq_end, where it can safely disable interrupts. */ + * within noirq_start and noirq_end, where it can safely disable interrupts. + */ -/*M:006 The Guests do not use the sysenter (fast system call) instruction, +/*M:006 + * The Guests do not use the sysenter (fast system call) instruction, * because it's hardcoded to enter privilege level 0 and so can't go direct. * It's about twice as fast as the older "int 0x80" system call, so it might * still be worthwhile to handle it in the Switcher and lcall down to the * Guest. The sysenter semantics are hairy tho: search for that keyword in - * entry.S :*/ + * entry.S +:*/ -/*H:260 When we make traps go directly into the Guest, we need to make sure +/*H:260 + * When we make traps go directly into the Guest, we need to make sure * the kernel stack is valid (ie. mapped in the page tables). Otherwise, the * CPU trying to deliver the trap will fault while trying to push the interrupt * words on the stack: this is called a double fault, and it forces us to kill * the Guest. * - * Which is deeply unfair, because (literally!) it wasn't the Guests' fault. */ + * Which is deeply unfair, because (literally!) it wasn't the Guests' fault. + */ void pin_stack_pages(struct lg_cpu *cpu) { unsigned int i; - /* Depending on the CONFIG_4KSTACKS option, the Guest can have one or - * two pages of stack space. */ + /* + * Depending on the CONFIG_4KSTACKS option, the Guest can have one or + * two pages of stack space. + */ for (i = 0; i < cpu->lg->stack_pages; i++) - /* The stack grows *upwards*, so the address we're given is the + /* + * The stack grows *upwards*, so the address we're given is the * start of the page after the kernel stack. Subtract one to * get back onto the first stack page, and keep subtracting to - * get to the rest of the stack pages. */ + * get to the rest of the stack pages. + */ pin_page(cpu, cpu->esp1 - 1 - i * PAGE_SIZE); } -/* Direct traps also mean that we need to know whenever the Guest wants to use +/* + * Direct traps also mean that we need to know whenever the Guest wants to use * a different kernel stack, so we can change the IDT entries to use that * stack. The IDT entries expect a virtual address, so unlike most addresses * the Guest gives us, the "esp" (stack pointer) value here is virtual, not * physical. * * In Linux each process has its own kernel stack, so this happens a lot: we - * change stacks on each context switch. */ + * change stacks on each context switch. + */ void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages) { - /* You are not allowed have a stack segment with privilege level 0: bad - * Guest! */ + /* + * You're not allowed a stack segment with privilege level 0: bad Guest! + */ if ((seg & 0x3) != GUEST_PL) kill_guest(cpu, "bad stack segment %i", seg); /* We only expect one or two stack pages. */ @@ -387,11 +454,15 @@ void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages) pin_stack_pages(cpu); } -/* All this reference to mapping stacks leads us neatly into the other complex - * part of the Host: page table handling. */ +/* + * All this reference to mapping stacks leads us neatly into the other complex + * part of the Host: page table handling. + */ -/*H:235 This is the routine which actually checks the Guest's IDT entry and - * transfers it into the entry in "struct lguest": */ +/*H:235 + * This is the routine which actually checks the Guest's IDT entry and + * transfers it into the entry in "struct lguest": + */ static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap, unsigned int num, u32 lo, u32 hi) { @@ -407,30 +478,38 @@ static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap, if (type != 0xE && type != 0xF) kill_guest(cpu, "bad IDT type %i", type); - /* We only copy the handler address, present bit, privilege level and + /* + * We only copy the handler address, present bit, privilege level and * type. The privilege level controls where the trap can be triggered * manually with an "int" instruction. This is usually GUEST_PL, - * except for system calls which userspace can use. */ + * except for system calls which userspace can use. + */ trap->a = ((__KERNEL_CS|GUEST_PL)<<16) | (lo&0x0000FFFF); trap->b = (hi&0xFFFFEF00); } -/*H:230 While we're here, dealing with delivering traps and interrupts to the +/*H:230 + * While we're here, dealing with delivering traps and interrupts to the * Guest, we might as well complete the picture: how the Guest tells us where * it wants them to go. This would be simple, except making traps fast * requires some tricks. * * We saw the Guest setting Interrupt Descriptor Table (IDT) entries with the - * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here. */ + * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here. + */ void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi) { - /* Guest never handles: NMI, doublefault, spurious interrupt or - * hypercall. We ignore when it tries to set them. */ + /* + * Guest never handles: NMI, doublefault, spurious interrupt or + * hypercall. We ignore when it tries to set them. + */ if (num == 2 || num == 8 || num == 15 || num == LGUEST_TRAP_ENTRY) return; - /* Mark the IDT as changed: next time the Guest runs we'll know we have - * to copy this again. */ + /* + * Mark the IDT as changed: next time the Guest runs we'll know we have + * to copy this again. + */ cpu->changed |= CHANGED_IDT; /* Check that the Guest doesn't try to step outside the bounds. */ @@ -440,9 +519,11 @@ void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi) set_trap(cpu, &cpu->arch.idt[num], num, lo, hi); } -/* The default entry for each interrupt points into the Switcher routines which +/* + * The default entry for each interrupt points into the Switcher routines which * simply return to the Host. The run_guest() loop will then call - * deliver_trap() to bounce it back into the Guest. */ + * deliver_trap() to bounce it back into the Guest. + */ static void default_idt_entry(struct desc_struct *idt, int trap, const unsigned long handler, @@ -451,13 +532,17 @@ static void default_idt_entry(struct desc_struct *idt, /* A present interrupt gate. */ u32 flags = 0x8e00; - /* Set the privilege level on the entry for the hypercall: this allows - * the Guest to use the "int" instruction to trigger it. */ + /* + * Set the privilege level on the entry for the hypercall: this allows + * the Guest to use the "int" instruction to trigger it. + */ if (trap == LGUEST_TRAP_ENTRY) flags |= (GUEST_PL << 13); else if (base) - /* Copy priv. level from what Guest asked for. This allows - * debug (int 3) traps from Guest userspace, for example. */ + /* + * Copy privilege level from what Guest asked for. This allows + * debug (int 3) traps from Guest userspace, for example. + */ flags |= (base->b & 0x6000); /* Now pack it into the IDT entry in its weird format. */ @@ -475,16 +560,20 @@ void setup_default_idt_entries(struct lguest_ro_state *state, default_idt_entry(&state->guest_idt[i], i, def[i], NULL); } -/*H:240 We don't use the IDT entries in the "struct lguest" directly, instead +/*H:240 + * We don't use the IDT entries in the "struct lguest" directly, instead * we copy them into the IDT which we've set up for Guests on this CPU, just - * before we run the Guest. This routine does that copy. */ + * before we run the Guest. This routine does that copy. + */ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, const unsigned long *def) { unsigned int i; - /* We can simply copy the direct traps, otherwise we use the default - * ones in the Switcher: they will return to the Host. */ + /* + * We can simply copy the direct traps, otherwise we use the default + * ones in the Switcher: they will return to the Host. + */ for (i = 0; i < ARRAY_SIZE(cpu->arch.idt); i++) { const struct desc_struct *gidt = &cpu->arch.idt[i]; @@ -492,14 +581,16 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, if (!direct_trap(i)) continue; - /* Only trap gates (type 15) can go direct to the Guest. + /* + * Only trap gates (type 15) can go direct to the Guest. * Interrupt gates (type 14) disable interrupts as they are * entered, which we never let the Guest do. Not present * entries (type 0x0) also can't go direct, of course. * * If it can't go direct, we still need to copy the priv. level: * they might want to give userspace access to a software - * interrupt. */ + * interrupt. + */ if (idt_type(gidt->a, gidt->b) == 0xF) idt[i] = *gidt; else @@ -518,7 +609,8 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt, * the next timer interrupt (in nanoseconds). We use the high-resolution timer * infrastructure to set a callback at that time. * - * 0 means "turn off the clock". */ + * 0 means "turn off the clock". + */ void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta) { ktime_t expires; @@ -529,9 +621,11 @@ void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta) return; } - /* We use wallclock time here, so the Guest might not be running for + /* + * We use wallclock time here, so the Guest might not be running for * all the time between now and the timer interrupt it asked for. This - * is almost always the right thing to do. */ + * is almost always the right thing to do. + */ expires = ktime_add_ns(ktime_get_real(), delta); hrtimer_start(&cpu->hrt, expires, HRTIMER_MODE_ABS); } diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h index 01c591923793..74c0db691b53 100644 --- a/drivers/lguest/lg.h +++ b/drivers/lguest/lg.h @@ -54,13 +54,13 @@ struct lg_cpu { unsigned long pending_notify; /* pfn from LHCALL_NOTIFY */ - /* At end of a page shared mapped over lguest_pages in guest. */ + /* At end of a page shared mapped over lguest_pages in guest. */ unsigned long regs_page; struct lguest_regs *regs; struct lguest_pages *last_pages; - int cpu_pgd; /* which pgd this cpu is currently using */ + int cpu_pgd; /* Which pgd this cpu is currently using */ /* If a hypercall was asked for, this points to the arguments. */ struct hcall_args *hcall; @@ -96,8 +96,11 @@ struct lguest unsigned int nr_cpus; u32 pfn_limit; - /* This provides the offset to the base of guest-physical - * memory in the Launcher. */ + + /* + * This provides the offset to the base of guest-physical memory in the + * Launcher. + */ void __user *mem_base; unsigned long kernel_address; @@ -122,11 +125,13 @@ bool lguest_address_ok(const struct lguest *lg, void __lgread(struct lg_cpu *, void *, unsigned long, unsigned); void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned); -/*H:035 Using memory-copy operations like that is usually inconvient, so we +/*H:035 + * Using memory-copy operations like that is usually inconvient, so we * have the following helper macros which read and write a specific type (often * an unsigned long). * - * This reads into a variable of the given type then returns that. */ + * This reads into a variable of the given type then returns that. + */ #define lgread(cpu, addr, type) \ ({ type _v; __lgread((cpu), &_v, (addr), sizeof(_v)); _v; }) @@ -140,9 +145,11 @@ void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned); int run_guest(struct lg_cpu *cpu, unsigned long __user *user); -/* Helper macros to obtain the first 12 or the last 20 bits, this is only the +/* + * Helper macros to obtain the first 12 or the last 20 bits, this is only the * first step in the migration to the kernel types. pte_pfn is already defined - * in the kernel. */ + * in the kernel. + */ #define pgd_flags(x) (pgd_val(x) & ~PAGE_MASK) #define pgd_pfn(x) (pgd_val(x) >> PAGE_SHIFT) #define pmd_flags(x) (pmd_val(x) & ~PAGE_MASK) diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index e082cdac88b4..cc000e79c3d1 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -1,10 +1,12 @@ -/*P:050 Lguest guests use a very simple method to describe devices. It's a +/*P:050 + * Lguest guests use a very simple method to describe devices. It's a * series of device descriptors contained just above the top of normal Guest * memory. * * We use the standard "virtio" device infrastructure, which provides us with a * console, a network and a block driver. Each one expects some configuration - * information and a "virtqueue" or two to send and receive data. :*/ + * information and a "virtqueue" or two to send and receive data. +:*/ #include #include #include @@ -20,8 +22,10 @@ /* The pointer to our (page) of device descriptions. */ static void *lguest_devices; -/* For Guests, device memory can be used as normal memory, so we cast away the - * __iomem to quieten sparse. */ +/* + * For Guests, device memory can be used as normal memory, so we cast away the + * __iomem to quieten sparse. + */ static inline void *lguest_map(unsigned long phys_addr, unsigned long pages) { return (__force void *)ioremap_cache(phys_addr, PAGE_SIZE*pages); @@ -32,8 +36,10 @@ static inline void lguest_unmap(void *addr) iounmap((__force void __iomem *)addr); } -/*D:100 Each lguest device is just a virtio device plus a pointer to its entry - * in the lguest_devices page. */ +/*D:100 + * Each lguest device is just a virtio device plus a pointer to its entry + * in the lguest_devices page. + */ struct lguest_device { struct virtio_device vdev; @@ -41,9 +47,11 @@ struct lguest_device { struct lguest_device_desc *desc; }; -/* Since the virtio infrastructure hands us a pointer to the virtio_device all +/* + * Since the virtio infrastructure hands us a pointer to the virtio_device all * the time, it helps to have a curt macro to get a pointer to the struct - * lguest_device it's enclosed in. */ + * lguest_device it's enclosed in. + */ #define to_lgdev(vd) container_of(vd, struct lguest_device, vdev) /*D:130 @@ -55,7 +63,8 @@ struct lguest_device { * the driver will look at them during setup. * * A convenient routine to return the device's virtqueue config array: - * immediately after the descriptor. */ + * immediately after the descriptor. + */ static struct lguest_vqconfig *lg_vq(const struct lguest_device_desc *desc) { return (void *)(desc + 1); @@ -98,10 +107,12 @@ static u32 lg_get_features(struct virtio_device *vdev) return features; } -/* The virtio core takes the features the Host offers, and copies the - * ones supported by the driver into the vdev->features array. Once - * that's all sorted out, this routine is called so we can tell the - * Host which features we understand and accept. */ +/* + * The virtio core takes the features the Host offers, and copies the ones + * supported by the driver into the vdev->features array. Once that's all + * sorted out, this routine is called so we can tell the Host which features we + * understand and accept. + */ static void lg_finalize_features(struct virtio_device *vdev) { unsigned int i, bits; @@ -112,10 +123,11 @@ static void lg_finalize_features(struct virtio_device *vdev) /* Give virtio_ring a chance to accept features. */ vring_transport_features(vdev); - /* The vdev->feature array is a Linux bitmask: this isn't the - * same as a the simple array of bits used by lguest devices - * for features. So we do this slow, manual conversion which is - * completely general. */ + /* + * The vdev->feature array is a Linux bitmask: this isn't the same as a + * the simple array of bits used by lguest devices for features. So we + * do this slow, manual conversion which is completely general. + */ memset(out_features, 0, desc->feature_len); bits = min_t(unsigned, desc->feature_len, sizeof(vdev->features)) * 8; for (i = 0; i < bits; i++) { @@ -146,15 +158,19 @@ static void lg_set(struct virtio_device *vdev, unsigned int offset, memcpy(lg_config(desc) + offset, buf, len); } -/* The operations to get and set the status word just access the status field - * of the device descriptor. */ +/* + * The operations to get and set the status word just access the status field + * of the device descriptor. + */ static u8 lg_get_status(struct virtio_device *vdev) { return to_lgdev(vdev)->desc->status; } -/* To notify on status updates, we (ab)use the NOTIFY hypercall, with the - * descriptor address of the device. A zero status means "reset". */ +/* + * To notify on status updates, we (ab)use the NOTIFY hypercall, with the + * descriptor address of the device. A zero status means "reset". + */ static void set_status(struct virtio_device *vdev, u8 status) { unsigned long offset = (void *)to_lgdev(vdev)->desc - lguest_devices; @@ -200,13 +216,17 @@ struct lguest_vq_info void *pages; }; -/* When the virtio_ring code wants to prod the Host, it calls us here and we +/* + * When the virtio_ring code wants to prod the Host, it calls us here and we * make a hypercall. We hand the physical address of the virtqueue so the Host - * knows which virtqueue we're talking about. */ + * knows which virtqueue we're talking about. + */ static void lg_notify(struct virtqueue *vq) { - /* We store our virtqueue information in the "priv" pointer of the - * virtqueue structure. */ + /* + * We store our virtqueue information in the "priv" pointer of the + * virtqueue structure. + */ struct lguest_vq_info *lvq = vq->priv; kvm_hypercall1(LHCALL_NOTIFY, lvq->config.pfn << PAGE_SHIFT); @@ -215,7 +235,8 @@ static void lg_notify(struct virtqueue *vq) /* An extern declaration inside a C file is bad form. Don't do it. */ extern void lguest_setup_irq(unsigned int irq); -/* This routine finds the first virtqueue described in the configuration of +/* + * This routine finds the first virtqueue described in the configuration of * this device and sets it up. * * This is kind of an ugly duckling. It'd be nicer to have a standard @@ -225,7 +246,8 @@ extern void lguest_setup_irq(unsigned int irq); * simpler for the Host to simply tell us where the pages are. * * So we provide drivers with a "find the Nth virtqueue and set it up" - * function. */ + * function. + */ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, unsigned index, void (*callback)(struct virtqueue *vq), @@ -244,9 +266,11 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, if (!lvq) return ERR_PTR(-ENOMEM); - /* Make a copy of the "struct lguest_vqconfig" entry, which sits after + /* + * Make a copy of the "struct lguest_vqconfig" entry, which sits after * the descriptor. We need a copy because the config space might not - * be aligned correctly. */ + * be aligned correctly. + */ memcpy(&lvq->config, lg_vq(ldev->desc)+index, sizeof(lvq->config)); printk("Mapping virtqueue %i addr %lx\n", index, @@ -261,8 +285,10 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, goto free_lvq; } - /* OK, tell virtio_ring.c to set up a virtqueue now we know its size - * and we've got a pointer to its pages. */ + /* + * OK, tell virtio_ring.c to set up a virtqueue now we know its size + * and we've got a pointer to its pages. + */ vq = vring_new_virtqueue(lvq->config.num, LGUEST_VRING_ALIGN, vdev, lvq->pages, lg_notify, callback, name); if (!vq) { @@ -273,18 +299,23 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, /* Make sure the interrupt is allocated. */ lguest_setup_irq(lvq->config.irq); - /* Tell the interrupt for this virtqueue to go to the virtio_ring - * interrupt handler. */ - /* FIXME: We used to have a flag for the Host to tell us we could use + /* + * Tell the interrupt for this virtqueue to go to the virtio_ring + * interrupt handler. + * + * FIXME: We used to have a flag for the Host to tell us we could use * the interrupt as a source of randomness: it'd be nice to have that - * back.. */ + * back. + */ err = request_irq(lvq->config.irq, vring_interrupt, IRQF_SHARED, dev_name(&vdev->dev), vq); if (err) goto destroy_vring; - /* Last of all we hook up our 'struct lguest_vq_info" to the - * virtqueue's priv pointer. */ + /* + * Last of all we hook up our 'struct lguest_vq_info" to the + * virtqueue's priv pointer. + */ vq->priv = lvq; return vq; @@ -358,11 +389,14 @@ static struct virtio_config_ops lguest_config_ops = { .del_vqs = lg_del_vqs, }; -/* The root device for the lguest virtio devices. This makes them appear as - * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2. */ +/* + * The root device for the lguest virtio devices. This makes them appear as + * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2. + */ static struct device *lguest_root; -/*D:120 This is the core of the lguest bus: actually adding a new device. +/*D:120 + * This is the core of the lguest bus: actually adding a new device. * It's a separate function because it's neater that way, and because an * earlier version of the code supported hotplug and unplug. They were removed * early on because they were never used. @@ -371,14 +405,14 @@ static struct device *lguest_root; * * It's worth reading this carefully: we start with a pointer to the new device * descriptor in the "lguest_devices" page, and the offset into the device - * descriptor page so we can uniquely identify it if things go badly wrong. */ + * descriptor page so we can uniquely identify it if things go badly wrong. + */ static void add_lguest_device(struct lguest_device_desc *d, unsigned int offset) { struct lguest_device *ldev; - /* Start with zeroed memory; Linux's device layer seems to count on - * it. */ + /* Start with zeroed memory; Linux's device layer counts on it. */ ldev = kzalloc(sizeof(*ldev), GFP_KERNEL); if (!ldev) { printk(KERN_EMERG "Cannot allocate lguest dev %u type %u\n", @@ -390,15 +424,19 @@ static void add_lguest_device(struct lguest_device_desc *d, ldev->vdev.dev.parent = lguest_root; /* We have a unique device index thanks to the dev_index counter. */ ldev->vdev.id.device = d->type; - /* We have a simple set of routines for querying the device's - * configuration information and setting its status. */ + /* + * We have a simple set of routines for querying the device's + * configuration information and setting its status. + */ ldev->vdev.config = &lguest_config_ops; /* And we remember the device's descriptor for lguest_config_ops. */ ldev->desc = d; - /* register_virtio_device() sets up the generic fields for the struct + /* + * register_virtio_device() sets up the generic fields for the struct * virtio_device and calls device_register(). This makes the bus - * infrastructure look for a matching driver. */ + * infrastructure look for a matching driver. + */ if (register_virtio_device(&ldev->vdev) != 0) { printk(KERN_ERR "Failed to register lguest dev %u type %u\n", offset, d->type); @@ -406,8 +444,10 @@ static void add_lguest_device(struct lguest_device_desc *d, } } -/*D:110 scan_devices() simply iterates through the device page. The type 0 is - * reserved to mean "end of devices". */ +/*D:110 + * scan_devices() simply iterates through the device page. The type 0 is + * reserved to mean "end of devices". + */ static void scan_devices(void) { unsigned int i; @@ -426,7 +466,8 @@ static void scan_devices(void) } } -/*D:105 Fairly early in boot, lguest_devices_init() is called to set up the +/*D:105 + * Fairly early in boot, lguest_devices_init() is called to set up the * lguest device infrastructure. We check that we are a Guest by checking * pv_info.name: there are other ways of checking, but this seems most * obvious to me. @@ -437,7 +478,8 @@ static void scan_devices(void) * correct sysfs incantation). * * Finally we call scan_devices() which adds all the devices found in the - * lguest_devices page. */ + * lguest_devices page. + */ static int __init lguest_devices_init(void) { if (strcmp(pv_info.name, "lguest") != 0) @@ -456,11 +498,13 @@ static int __init lguest_devices_init(void) /* We do this after core stuff, but before the drivers. */ postcore_initcall(lguest_devices_init); -/*D:150 At this point in the journey we used to now wade through the lguest +/*D:150 + * At this point in the journey we used to now wade through the lguest * devices themselves: net, block and console. Since they're all now virtio * devices rather than lguest-specific, I've decided to ignore them. Mostly, * they're kind of boring. But this does mean you'll never experience the * thrill of reading the forbidden love scene buried deep in the block driver. * * "make Launcher" beckons, where we answer questions like "Where do Guests - * come from?", and "What do you do when someone asks for optimization?". */ + * come from?", and "What do you do when someone asks for optimization?". + */ diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 407722a8e0c4..7e92017103dc 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -1,8 +1,10 @@ -/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher +/*P:200 + * This contains all the /dev/lguest code, whereby the userspace launcher * controls and communicates with the Guest. For example, the first write will * tell us the Guest's memory layout, pagetable, entry point and kernel address * offset. A read will run the Guest until something happens, such as a signal - * or the Guest doing a NOTIFY out to the Launcher. :*/ + * or the Guest doing a NOTIFY out to the Launcher. +:*/ #include #include #include @@ -37,8 +39,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) if (!addr) return -EINVAL; - /* Replace the old array with the new one, carefully: others can - * be accessing it at the same time */ + /* + * Replace the old array with the new one, carefully: others can + * be accessing it at the same time. + */ new = kmalloc(sizeof(*new) + sizeof(new->map[0]) * (old->num + 1), GFP_KERNEL); if (!new) @@ -61,8 +65,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) /* Now put new one in place. */ rcu_assign_pointer(lg->eventfds, new); - /* We're not in a big hurry. Wait until noone's looking at old - * version, then delete it. */ + /* + * We're not in a big hurry. Wait until noone's looking at old + * version, then delete it. + */ synchronize_rcu(); kfree(old); @@ -87,8 +93,10 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) return err; } -/*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt - * number to /dev/lguest. */ +/*L:050 + * Sending an interrupt is done by writing LHREQ_IRQ and an interrupt + * number to /dev/lguest. + */ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) { unsigned long irq; @@ -102,8 +110,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) return 0; } -/*L:040 Once our Guest is initialized, the Launcher makes it run by reading - * from /dev/lguest. */ +/*L:040 + * Once our Guest is initialized, the Launcher makes it run by reading + * from /dev/lguest. + */ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) { struct lguest *lg = file->private_data; @@ -139,8 +149,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) return len; } - /* If we returned from read() last time because the Guest sent I/O, - * clear the flag. */ + /* + * If we returned from read() last time because the Guest sent I/O, + * clear the flag. + */ if (cpu->pending_notify) cpu->pending_notify = 0; @@ -148,8 +160,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o) return run_guest(cpu, (unsigned long __user *)user); } -/*L:025 This actually initializes a CPU. For the moment, a Guest is only - * uniprocessor, so "id" is always 0. */ +/*L:025 + * This actually initializes a CPU. For the moment, a Guest is only + * uniprocessor, so "id" is always 0. + */ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) { /* We have a limited number the number of CPUs in the lguest struct. */ @@ -164,8 +178,10 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) /* Each CPU has a timer it can set. */ init_clockdev(cpu); - /* We need a complete page for the Guest registers: they are accessible - * to the Guest and we can only grant it access to whole pages. */ + /* + * We need a complete page for the Guest registers: they are accessible + * to the Guest and we can only grant it access to whole pages. + */ cpu->regs_page = get_zeroed_page(GFP_KERNEL); if (!cpu->regs_page) return -ENOMEM; @@ -173,29 +189,38 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) /* We actually put the registers at the bottom of the page. */ cpu->regs = (void *)cpu->regs_page + PAGE_SIZE - sizeof(*cpu->regs); - /* Now we initialize the Guest's registers, handing it the start - * address. */ + /* + * Now we initialize the Guest's registers, handing it the start + * address. + */ lguest_arch_setup_regs(cpu, start_ip); - /* We keep a pointer to the Launcher task (ie. current task) for when - * other Guests want to wake this one (eg. console input). */ + /* + * We keep a pointer to the Launcher task (ie. current task) for when + * other Guests want to wake this one (eg. console input). + */ cpu->tsk = current; - /* We need to keep a pointer to the Launcher's memory map, because if + /* + * We need to keep a pointer to the Launcher's memory map, because if * the Launcher dies we need to clean it up. If we don't keep a - * reference, it is destroyed before close() is called. */ + * reference, it is destroyed before close() is called. + */ cpu->mm = get_task_mm(cpu->tsk); - /* We remember which CPU's pages this Guest used last, for optimization - * when the same Guest runs on the same CPU twice. */ + /* + * We remember which CPU's pages this Guest used last, for optimization + * when the same Guest runs on the same CPU twice. + */ cpu->last_pages = NULL; /* No error == success. */ return 0; } -/*L:020 The initialization write supplies 3 pointer sized (32 or 64 bit) - * values (in addition to the LHREQ_INITIALIZE value). These are: +/*L:020 + * The initialization write supplies 3 pointer sized (32 or 64 bit) values (in + * addition to the LHREQ_INITIALIZE value). These are: * * base: The start of the Guest-physical memory inside the Launcher memory. * @@ -207,14 +232,15 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip) */ static int initialize(struct file *file, const unsigned long __user *input) { - /* "struct lguest" contains everything we (the Host) know about a - * Guest. */ + /* "struct lguest" contains all we (the Host) know about a Guest. */ struct lguest *lg; int err; unsigned long args[3]; - /* We grab the Big Lguest lock, which protects against multiple - * simultaneous initializations. */ + /* + * We grab the Big Lguest lock, which protects against multiple + * simultaneous initializations. + */ mutex_lock(&lguest_lock); /* You can't initialize twice! Close the device and start again... */ if (file->private_data) { @@ -249,8 +275,10 @@ static int initialize(struct file *file, const unsigned long __user *input) if (err) goto free_eventfds; - /* Initialize the Guest's shadow page tables, using the toplevel - * address the Launcher gave us. This allocates memory, so can fail. */ + /* + * Initialize the Guest's shadow page tables, using the toplevel + * address the Launcher gave us. This allocates memory, so can fail. + */ err = init_guest_pagetable(lg); if (err) goto free_regs; @@ -275,7 +303,8 @@ unlock: return err; } -/*L:010 The first operation the Launcher does must be a write. All writes +/*L:010 + * The first operation the Launcher does must be a write. All writes * start with an unsigned long number: for the first write this must be * LHREQ_INITIALIZE to set up the Guest. After that the Launcher can use * writes of other values to send interrupts. @@ -283,12 +312,15 @@ unlock: * Note that we overload the "offset" in the /dev/lguest file to indicate what * CPU number we're dealing with. Currently this is always 0, since we only * support uniprocessor Guests, but you can see the beginnings of SMP support - * here. */ + * here. + */ static ssize_t write(struct file *file, const char __user *in, size_t size, loff_t *off) { - /* Once the Guest is initialized, we hold the "struct lguest" in the - * file private data. */ + /* + * Once the Guest is initialized, we hold the "struct lguest" in the + * file private data. + */ struct lguest *lg = file->private_data; const unsigned long __user *input = (const unsigned long __user *)in; unsigned long req; @@ -323,13 +355,15 @@ static ssize_t write(struct file *file, const char __user *in, } } -/*L:060 The final piece of interface code is the close() routine. It reverses +/*L:060 + * The final piece of interface code is the close() routine. It reverses * everything done in initialize(). This is usually called because the * Launcher exited. * * Note that the close routine returns 0 or a negative error number: it can't * really fail, but it can whine. I blame Sun for this wart, and K&R C for - * letting them do it. :*/ + * letting them do it. +:*/ static int close(struct inode *inode, struct file *file) { struct lguest *lg = file->private_data; @@ -339,8 +373,10 @@ static int close(struct inode *inode, struct file *file) if (!lg) return 0; - /* We need the big lock, to protect from inter-guest I/O and other - * Launchers initializing guests. */ + /* + * We need the big lock, to protect from inter-guest I/O and other + * Launchers initializing guests. + */ mutex_lock(&lguest_lock); /* Free up the shadow page tables for the Guest. */ @@ -351,8 +387,10 @@ static int close(struct inode *inode, struct file *file) hrtimer_cancel(&lg->cpus[i].hrt); /* We can free up the register page we allocated. */ free_page(lg->cpus[i].regs_page); - /* Now all the memory cleanups are done, it's safe to release - * the Launcher's memory management structure. */ + /* + * Now all the memory cleanups are done, it's safe to release + * the Launcher's memory management structure. + */ mmput(lg->cpus[i].mm); } @@ -361,8 +399,10 @@ static int close(struct inode *inode, struct file *file) eventfd_ctx_put(lg->eventfds->map[i].event); kfree(lg->eventfds); - /* If lg->dead doesn't contain an error code it will be NULL or a - * kmalloc()ed string, either of which is ok to hand to kfree(). */ + /* + * If lg->dead doesn't contain an error code it will be NULL or a + * kmalloc()ed string, either of which is ok to hand to kfree(). + */ if (!IS_ERR(lg->dead)) kfree(lg->dead); /* Free the memory allocated to the lguest_struct */ @@ -386,7 +426,8 @@ static int close(struct inode *inode, struct file *file) * * We begin our understanding with the Host kernel interface which the Launcher * uses: reading and writing a character device called /dev/lguest. All the - * work happens in the read(), write() and close() routines: */ + * work happens in the read(), write() and close() routines: + */ static struct file_operations lguest_fops = { .owner = THIS_MODULE, .release = close, @@ -394,8 +435,10 @@ static struct file_operations lguest_fops = { .read = read, }; -/* This is a textbook example of a "misc" character device. Populate a "struct - * miscdevice" and register it with misc_register(). */ +/* + * This is a textbook example of a "misc" character device. Populate a "struct + * miscdevice" and register it with misc_register(). + */ static struct miscdevice lguest_dev = { .minor = MISC_DYNAMIC_MINOR, .name = "lguest", diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c index a6fe1abda240..3da902e4b4cb 100644 --- a/drivers/lguest/page_tables.c +++ b/drivers/lguest/page_tables.c @@ -1,9 +1,11 @@ -/*P:700 The pagetable code, on the other hand, still shows the scars of +/*P:700 + * The pagetable code, on the other hand, still shows the scars of * previous encounters. It's functional, and as neat as it can be in the * circumstances, but be wary, for these things are subtle and break easily. * The Guest provides a virtual to physical mapping, but we can neither trust * it nor use it: we verify and convert it here then point the CPU to the - * converted Guest pages when running the Guest. :*/ + * converted Guest pages when running the Guest. +:*/ /* Copyright (C) Rusty Russell IBM Corporation 2006. * GPL v2 and any later version */ @@ -17,10 +19,12 @@ #include #include "lg.h" -/*M:008 We hold reference to pages, which prevents them from being swapped. +/*M:008 + * We hold reference to pages, which prevents them from being swapped. * It'd be nice to have a callback in the "struct mm_struct" when Linux wants * to swap out. If we had this, and a shrinker callback to trim PTE pages, we - * could probably consider launching Guests as non-root. :*/ + * could probably consider launching Guests as non-root. +:*/ /*H:300 * The Page Table Code @@ -45,16 +49,19 @@ * (v) Flushing (throwing away) page tables, * (vi) Mapping the Switcher when the Guest is about to run, * (vii) Setting up the page tables initially. - :*/ +:*/ - -/* 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is +/* + * 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is * conveniently placed at the top 4MB, so it uses a separate, complete PTE - * page. */ + * page. + */ #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1) -/* For PAE we need the PMD index as well. We use the last 2MB, so we - * will need the last pmd entry of the last pmd page. */ +/* + * For PAE we need the PMD index as well. We use the last 2MB, so we + * will need the last pmd entry of the last pmd page. + */ #ifdef CONFIG_X86_PAE #define SWITCHER_PMD_INDEX (PTRS_PER_PMD - 1) #define RESERVE_MEM 2U @@ -64,13 +71,16 @@ #define CHECK_GPGD_MASK _PAGE_TABLE #endif -/* We actually need a separate PTE page for each CPU. Remember that after the +/* + * We actually need a separate PTE page for each CPU. Remember that after the * Switcher code itself comes two pages for each CPU, and we don't want this - * CPU's guest to see the pages of any other CPU. */ + * CPU's guest to see the pages of any other CPU. + */ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); #define switcher_pte_page(cpu) per_cpu(switcher_pte_pages, cpu) -/*H:320 The page table code is curly enough to need helper functions to keep it +/*H:320 + * The page table code is curly enough to need helper functions to keep it * clear and clean. * * There are two functions which return pointers to the shadow (aka "real") @@ -79,7 +89,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); * spgd_addr() takes the virtual address and returns a pointer to the top-level * page directory entry (PGD) for that address. Since we keep track of several * page tables, the "i" argument tells us which one we're interested in (it's - * usually the current one). */ + * usually the current one). + */ static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr) { unsigned int index = pgd_index(vaddr); @@ -96,9 +107,11 @@ static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr) } #ifdef CONFIG_X86_PAE -/* This routine then takes the PGD entry given above, which contains the +/* + * This routine then takes the PGD entry given above, which contains the * address of the PMD page. It then returns a pointer to the PMD entry for the - * given address. */ + * given address. + */ static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) { unsigned int index = pmd_index(vaddr); @@ -119,9 +132,11 @@ static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) } #endif -/* This routine then takes the page directory entry returned above, which +/* + * This routine then takes the page directory entry returned above, which * contains the address of the page table entry (PTE) page. It then returns a - * pointer to the PTE entry for the given address. */ + * pointer to the PTE entry for the given address. + */ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) { #ifdef CONFIG_X86_PAE @@ -139,8 +154,10 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) return &page[pte_index(vaddr)]; } -/* These two functions just like the above two, except they access the Guest - * page tables. Hence they return a Guest address. */ +/* + * These two functions just like the above two, except they access the Guest + * page tables. Hence they return a Guest address. + */ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) { unsigned int index = vaddr >> (PGDIR_SHIFT); @@ -175,17 +192,21 @@ static unsigned long gpte_addr(struct lg_cpu *cpu, #endif /*:*/ -/*M:014 get_pfn is slow: we could probably try to grab batches of pages here as - * an optimization (ie. pre-faulting). :*/ +/*M:014 + * get_pfn is slow: we could probably try to grab batches of pages here as + * an optimization (ie. pre-faulting). +:*/ -/*H:350 This routine takes a page number given by the Guest and converts it to +/*H:350 + * This routine takes a page number given by the Guest and converts it to * an actual, physical page number. It can fail for several reasons: the * virtual address might not be mapped by the Launcher, the write flag is set * and the page is read-only, or the write flag was set and the page was * shared so had to be copied, but we ran out of memory. * * This holds a reference to the page, so release_pte() is careful to put that - * back. */ + * back. + */ static unsigned long get_pfn(unsigned long virtpfn, int write) { struct page *page; @@ -198,33 +219,41 @@ static unsigned long get_pfn(unsigned long virtpfn, int write) return -1UL; } -/*H:340 Converting a Guest page table entry to a shadow (ie. real) page table +/*H:340 + * Converting a Guest page table entry to a shadow (ie. real) page table * entry can be a little tricky. The flags are (almost) the same, but the * Guest PTE contains a virtual page number: the CPU needs the real page - * number. */ + * number. + */ static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write) { unsigned long pfn, base, flags; - /* The Guest sets the global flag, because it thinks that it is using + /* + * The Guest sets the global flag, because it thinks that it is using * PGE. We only told it to use PGE so it would tell us whether it was * flushing a kernel mapping or a userspace mapping. We don't actually - * use the global bit, so throw it away. */ + * use the global bit, so throw it away. + */ flags = (pte_flags(gpte) & ~_PAGE_GLOBAL); /* The Guest's pages are offset inside the Launcher. */ base = (unsigned long)cpu->lg->mem_base / PAGE_SIZE; - /* We need a temporary "unsigned long" variable to hold the answer from + /* + * We need a temporary "unsigned long" variable to hold the answer from * get_pfn(), because it returns 0xFFFFFFFF on failure, which wouldn't * fit in spte.pfn. get_pfn() finds the real physical number of the - * page, given the virtual number. */ + * page, given the virtual number. + */ pfn = get_pfn(base + pte_pfn(gpte), write); if (pfn == -1UL) { kill_guest(cpu, "failed to get page %lu", pte_pfn(gpte)); - /* When we destroy the Guest, we'll go through the shadow page + /* + * When we destroy the Guest, we'll go through the shadow page * tables and release_pte() them. Make sure we don't think - * this one is valid! */ + * this one is valid! + */ flags = 0; } /* Now we assemble our shadow PTE from the page number and flags. */ @@ -234,8 +263,10 @@ static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write) /*H:460 And to complete the chain, release_pte() looks like this: */ static void release_pte(pte_t pte) { - /* Remember that get_user_pages_fast() took a reference to the page, in - * get_pfn()? We have to put it back now. */ + /* + * Remember that get_user_pages_fast() took a reference to the page, in + * get_pfn()? We have to put it back now. + */ if (pte_flags(pte) & _PAGE_PRESENT) put_page(pte_page(pte)); } @@ -273,7 +304,8 @@ static void check_gpmd(struct lg_cpu *cpu, pmd_t gpmd) * and return to the Guest without it knowing. * * If we fixed up the fault (ie. we mapped the address), this routine returns - * true. Otherwise, it was a real fault and we need to tell the Guest. */ + * true. Otherwise, it was a real fault and we need to tell the Guest. + */ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) { pgd_t gpgd; @@ -298,22 +330,26 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if (!(pgd_flags(*spgd) & _PAGE_PRESENT)) { /* No shadow entry: allocate a new shadow PTE page. */ unsigned long ptepage = get_zeroed_page(GFP_KERNEL); - /* This is not really the Guest's fault, but killing it is - * simple for this corner case. */ + /* + * This is not really the Guest's fault, but killing it is + * simple for this corner case. + */ if (!ptepage) { kill_guest(cpu, "out of memory allocating pte page"); return false; } /* We check that the Guest pgd is OK. */ check_gpgd(cpu, gpgd); - /* And we copy the flags to the shadow PGD entry. The page - * number in the shadow PGD is the page we just allocated. */ + /* + * And we copy the flags to the shadow PGD entry. The page + * number in the shadow PGD is the page we just allocated. + */ set_pgd(spgd, __pgd(__pa(ptepage) | pgd_flags(gpgd))); } #ifdef CONFIG_X86_PAE gpmd = lgread(cpu, gpmd_addr(gpgd, vaddr), pmd_t); - /* middle level not present? We can't map it in. */ + /* Middle level not present? We can't map it in. */ if (!(pmd_flags(gpmd) & _PAGE_PRESENT)) return false; @@ -324,8 +360,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* No shadow entry: allocate a new shadow PTE page. */ unsigned long ptepage = get_zeroed_page(GFP_KERNEL); - /* This is not really the Guest's fault, but killing it is - * simple for this corner case. */ + /* + * This is not really the Guest's fault, but killing it is + * simple for this corner case. + */ if (!ptepage) { kill_guest(cpu, "out of memory allocating pte page"); return false; @@ -334,17 +372,23 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* We check that the Guest pmd is OK. */ check_gpmd(cpu, gpmd); - /* And we copy the flags to the shadow PMD entry. The page - * number in the shadow PMD is the page we just allocated. */ + /* + * And we copy the flags to the shadow PMD entry. The page + * number in the shadow PMD is the page we just allocated. + */ native_set_pmd(spmd, __pmd(__pa(ptepage) | pmd_flags(gpmd))); } - /* OK, now we look at the lower level in the Guest page table: keep its - * address, because we might update it later. */ + /* + * OK, now we look at the lower level in the Guest page table: keep its + * address, because we might update it later. + */ gpte_ptr = gpte_addr(cpu, gpmd, vaddr); #else - /* OK, now we look at the lower level in the Guest page table: keep its - * address, because we might update it later. */ + /* + * OK, now we look at the lower level in the Guest page table: keep its + * address, because we might update it later. + */ gpte_ptr = gpte_addr(cpu, gpgd, vaddr); #endif gpte = lgread(cpu, gpte_ptr, pte_t); @@ -353,8 +397,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if (!(pte_flags(gpte) & _PAGE_PRESENT)) return false; - /* Check they're not trying to write to a page the Guest wants - * read-only (bit 2 of errcode == write). */ + /* + * Check they're not trying to write to a page the Guest wants + * read-only (bit 2 of errcode == write). + */ if ((errcode & 2) && !(pte_flags(gpte) & _PAGE_RW)) return false; @@ -362,8 +408,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) if ((errcode & 4) && !(pte_flags(gpte) & _PAGE_USER)) return false; - /* Check that the Guest PTE flags are OK, and the page number is below - * the pfn_limit (ie. not mapping the Launcher binary). */ + /* + * Check that the Guest PTE flags are OK, and the page number is below + * the pfn_limit (ie. not mapping the Launcher binary). + */ check_gpte(cpu, gpte); /* Add the _PAGE_ACCESSED and (for a write) _PAGE_DIRTY flag */ @@ -373,29 +421,40 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) /* Get the pointer to the shadow PTE entry we're going to set. */ spte = spte_addr(cpu, *spgd, vaddr); - /* If there was a valid shadow PTE entry here before, we release it. - * This can happen with a write to a previously read-only entry. */ + + /* + * If there was a valid shadow PTE entry here before, we release it. + * This can happen with a write to a previously read-only entry. + */ release_pte(*spte); - /* If this is a write, we insist that the Guest page is writable (the - * final arg to gpte_to_spte()). */ + /* + * If this is a write, we insist that the Guest page is writable (the + * final arg to gpte_to_spte()). + */ if (pte_dirty(gpte)) *spte = gpte_to_spte(cpu, gpte, 1); else - /* If this is a read, don't set the "writable" bit in the page + /* + * If this is a read, don't set the "writable" bit in the page * table entry, even if the Guest says it's writable. That way * we will come back here when a write does actually occur, so - * we can update the Guest's _PAGE_DIRTY flag. */ + * we can update the Guest's _PAGE_DIRTY flag. + */ native_set_pte(spte, gpte_to_spte(cpu, pte_wrprotect(gpte), 0)); - /* Finally, we write the Guest PTE entry back: we've set the - * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags. */ + /* + * Finally, we write the Guest PTE entry back: we've set the + * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags. + */ lgwrite(cpu, gpte_ptr, pte_t, gpte); - /* The fault is fixed, the page table is populated, the mapping + /* + * The fault is fixed, the page table is populated, the mapping * manipulated, the result returned and the code complete. A small * delay and a trace of alliteration are the only indications the Guest - * has that a page fault occurred at all. */ + * has that a page fault occurred at all. + */ return true; } @@ -408,7 +467,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) * mapped, so it's overkill. * * This is a quick version which answers the question: is this virtual address - * mapped by the shadow page tables, and is it writable? */ + * mapped by the shadow page tables, and is it writable? + */ static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr) { pgd_t *spgd; @@ -428,16 +488,20 @@ static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr) return false; #endif - /* Check the flags on the pte entry itself: it must be present and - * writable. */ + /* + * Check the flags on the pte entry itself: it must be present and + * writable. + */ flags = pte_flags(*(spte_addr(cpu, *spgd, vaddr))); return (flags & (_PAGE_PRESENT|_PAGE_RW)) == (_PAGE_PRESENT|_PAGE_RW); } -/* So, when pin_stack_pages() asks us to pin a page, we check if it's already +/* + * So, when pin_stack_pages() asks us to pin a page, we check if it's already * in the page tables, and if not, we call demand_page() with error code 2 - * (meaning "write"). */ + * (meaning "write"). + */ void pin_page(struct lg_cpu *cpu, unsigned long vaddr) { if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2)) @@ -485,9 +549,11 @@ static void release_pgd(pgd_t *spgd) /* If the entry's not present, there's nothing to release. */ if (pgd_flags(*spgd) & _PAGE_PRESENT) { unsigned int i; - /* Converting the pfn to find the actual PTE page is easy: turn + /* + * Converting the pfn to find the actual PTE page is easy: turn * the page number into a physical address, then convert to a - * virtual address (easy for kernel pages like this one). */ + * virtual address (easy for kernel pages like this one). + */ pte_t *ptepage = __va(pgd_pfn(*spgd) << PAGE_SHIFT); /* For each entry in the page, we might need to release it. */ for (i = 0; i < PTRS_PER_PTE; i++) @@ -499,9 +565,12 @@ static void release_pgd(pgd_t *spgd) } } #endif -/*H:445 We saw flush_user_mappings() twice: once from the flush_user_mappings() + +/*H:445 + * We saw flush_user_mappings() twice: once from the flush_user_mappings() * hypercall and once in new_pgdir() when we re-used a top-level pgdir page. - * It simply releases every PTE page from 0 up to the Guest's kernel address. */ + * It simply releases every PTE page from 0 up to the Guest's kernel address. + */ static void flush_user_mappings(struct lguest *lg, int idx) { unsigned int i; @@ -510,10 +579,12 @@ static void flush_user_mappings(struct lguest *lg, int idx) release_pgd(lg->pgdirs[idx].pgdir + i); } -/*H:440 (v) Flushing (throwing away) page tables, +/*H:440 + * (v) Flushing (throwing away) page tables, * * The Guest has a hypercall to throw away the page tables: it's used when a - * large number of mappings have been changed. */ + * large number of mappings have been changed. + */ void guest_pagetable_flush_user(struct lg_cpu *cpu) { /* Drop the userspace part of the current page table. */ @@ -551,9 +622,11 @@ unsigned long guest_pa(struct lg_cpu *cpu, unsigned long vaddr) return pte_pfn(gpte) * PAGE_SIZE | (vaddr & ~PAGE_MASK); } -/* We keep several page tables. This is a simple routine to find the page +/* + * We keep several page tables. This is a simple routine to find the page * table (if any) corresponding to this top-level address the Guest has given - * us. */ + * us. + */ static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable) { unsigned int i; @@ -563,9 +636,11 @@ static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable) return i; } -/*H:435 And this is us, creating the new page directory. If we really do +/*H:435 + * And this is us, creating the new page directory. If we really do * allocate a new one (and so the kernel parts are not there), we set - * blank_pgdir. */ + * blank_pgdir. + */ static unsigned int new_pgdir(struct lg_cpu *cpu, unsigned long gpgdir, int *blank_pgdir) @@ -575,8 +650,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, pmd_t *pmd_table; #endif - /* We pick one entry at random to throw out. Choosing the Least - * Recently Used might be better, but this is easy. */ + /* + * We pick one entry at random to throw out. Choosing the Least + * Recently Used might be better, but this is easy. + */ next = random32() % ARRAY_SIZE(cpu->lg->pgdirs); /* If it's never been allocated at all before, try now. */ if (!cpu->lg->pgdirs[next].pgdir) { @@ -587,8 +664,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, next = cpu->cpu_pgd; else { #ifdef CONFIG_X86_PAE - /* In PAE mode, allocate a pmd page and populate the - * last pgd entry. */ + /* + * In PAE mode, allocate a pmd page and populate the + * last pgd entry. + */ pmd_table = (pmd_t *)get_zeroed_page(GFP_KERNEL); if (!pmd_table) { free_page((long)cpu->lg->pgdirs[next].pgdir); @@ -598,8 +677,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, set_pgd(cpu->lg->pgdirs[next].pgdir + SWITCHER_PGD_INDEX, __pgd(__pa(pmd_table) | _PAGE_PRESENT)); - /* This is a blank page, so there are no kernel - * mappings: caller must map the stack! */ + /* + * This is a blank page, so there are no kernel + * mappings: caller must map the stack! + */ *blank_pgdir = 1; } #else @@ -615,19 +696,23 @@ static unsigned int new_pgdir(struct lg_cpu *cpu, return next; } -/*H:430 (iv) Switching page tables +/*H:430 + * (iv) Switching page tables * * Now we've seen all the page table setting and manipulation, let's see * what happens when the Guest changes page tables (ie. changes the top-level - * pgdir). This occurs on almost every context switch. */ + * pgdir). This occurs on almost every context switch. + */ void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable) { int newpgdir, repin = 0; /* Look to see if we have this one already. */ newpgdir = find_pgdir(cpu->lg, pgtable); - /* If not, we allocate or mug an existing one: if it's a fresh one, - * repin gets set to 1. */ + /* + * If not, we allocate or mug an existing one: if it's a fresh one, + * repin gets set to 1. + */ if (newpgdir == ARRAY_SIZE(cpu->lg->pgdirs)) newpgdir = new_pgdir(cpu, pgtable, &repin); /* Change the current pgd index to the new one. */ @@ -637,9 +722,11 @@ void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable) pin_stack_pages(cpu); } -/*H:470 Finally, a routine which throws away everything: all PGD entries in all +/*H:470 + * Finally, a routine which throws away everything: all PGD entries in all * the shadow page tables, including the Guest's kernel mappings. This is used - * when we destroy the Guest. */ + * when we destroy the Guest. + */ static void release_all_pagetables(struct lguest *lg) { unsigned int i, j; @@ -656,8 +743,10 @@ static void release_all_pagetables(struct lguest *lg) spgd = lg->pgdirs[i].pgdir + SWITCHER_PGD_INDEX; pmdpage = __va(pgd_pfn(*spgd) << PAGE_SHIFT); - /* And release the pmd entries of that pmd page, - * except for the switcher pmd. */ + /* + * And release the pmd entries of that pmd page, + * except for the switcher pmd. + */ for (k = 0; k < SWITCHER_PMD_INDEX; k++) release_pmd(&pmdpage[k]); #endif @@ -667,10 +756,12 @@ static void release_all_pagetables(struct lguest *lg) } } -/* We also throw away everything when a Guest tells us it's changed a kernel +/* + * We also throw away everything when a Guest tells us it's changed a kernel * mapping. Since kernel mappings are in every page table, it's easiest to * throw them all away. This traps the Guest in amber for a while as - * everything faults back in, but it's rare. */ + * everything faults back in, but it's rare. + */ void guest_pagetable_clear_all(struct lg_cpu *cpu) { release_all_pagetables(cpu->lg); @@ -678,15 +769,19 @@ void guest_pagetable_clear_all(struct lg_cpu *cpu) pin_stack_pages(cpu); } /*:*/ -/*M:009 Since we throw away all mappings when a kernel mapping changes, our + +/*M:009 + * Since we throw away all mappings when a kernel mapping changes, our * performance sucks for guests using highmem. In fact, a guest with * PAGE_OFFSET 0xc0000000 (the default) and more than about 700MB of RAM is * usually slower than a Guest with less memory. * * This, of course, cannot be fixed. It would take some kind of... well, I - * don't know, but the term "puissant code-fu" comes to mind. :*/ + * don't know, but the term "puissant code-fu" comes to mind. +:*/ -/*H:420 This is the routine which actually sets the page table entry for then +/*H:420 + * This is the routine which actually sets the page table entry for then * "idx"'th shadow page table. * * Normally, we can just throw out the old entry and replace it with 0: if they @@ -715,31 +810,36 @@ static void do_set_pte(struct lg_cpu *cpu, int idx, spmd = spmd_addr(cpu, *spgd, vaddr); if (pmd_flags(*spmd) & _PAGE_PRESENT) { #endif - /* Otherwise, we start by releasing - * the existing entry. */ + /* Otherwise, start by releasing the existing entry. */ pte_t *spte = spte_addr(cpu, *spgd, vaddr); release_pte(*spte); - /* If they're setting this entry as dirty or accessed, - * we might as well put that entry they've given us - * in now. This shaves 10% off a - * copy-on-write micro-benchmark. */ + /* + * If they're setting this entry as dirty or accessed, + * we might as well put that entry they've given us in + * now. This shaves 10% off a copy-on-write + * micro-benchmark. + */ if (pte_flags(gpte) & (_PAGE_DIRTY | _PAGE_ACCESSED)) { check_gpte(cpu, gpte); native_set_pte(spte, gpte_to_spte(cpu, gpte, pte_flags(gpte) & _PAGE_DIRTY)); - } else - /* Otherwise kill it and we can demand_page() - * it in later. */ + } else { + /* + * Otherwise kill it and we can demand_page() + * it in later. + */ native_set_pte(spte, __pte(0)); + } #ifdef CONFIG_X86_PAE } #endif } } -/*H:410 Updating a PTE entry is a little trickier. +/*H:410 + * Updating a PTE entry is a little trickier. * * We keep track of several different page tables (the Guest uses one for each * process, so it makes sense to cache at least a few). Each of these have @@ -748,12 +848,15 @@ static void do_set_pte(struct lg_cpu *cpu, int idx, * all the page tables, not just the current one. This is rare. * * The benefit is that when we have to track a new page table, we can keep all - * the kernel mappings. This speeds up context switch immensely. */ + * the kernel mappings. This speeds up context switch immensely. + */ void guest_set_pte(struct lg_cpu *cpu, unsigned long gpgdir, unsigned long vaddr, pte_t gpte) { - /* Kernel mappings must be changed on all top levels. Slow, but doesn't - * happen often. */ + /* + * Kernel mappings must be changed on all top levels. Slow, but doesn't + * happen often. + */ if (vaddr >= cpu->lg->kernel_address) { unsigned int i; for (i = 0; i < ARRAY_SIZE(cpu->lg->pgdirs); i++) @@ -802,12 +905,14 @@ void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx) } #endif -/* Once we know how much memory we have we can construct simple identity - * (which set virtual == physical) and linear mappings - * which will get the Guest far enough into the boot to create its own. +/* + * Once we know how much memory we have we can construct simple identity (which + * set virtual == physical) and linear mappings which will get the Guest far + * enough into the boot to create its own. * * We lay them out of the way, just below the initrd (which is why we need to - * know its size here). */ + * know its size here). + */ static unsigned long setup_pagetables(struct lguest *lg, unsigned long mem, unsigned long initrd_size) @@ -825,8 +930,10 @@ static unsigned long setup_pagetables(struct lguest *lg, unsigned int phys_linear; #endif - /* We have mapped_pages frames to map, so we need - * linear_pages page tables to map them. */ + /* + * We have mapped_pages frames to map, so we need linear_pages page + * tables to map them. + */ mapped_pages = mem / PAGE_SIZE; linear_pages = (mapped_pages + PTRS_PER_PTE - 1) / PTRS_PER_PTE; @@ -839,8 +946,10 @@ static unsigned long setup_pagetables(struct lguest *lg, #ifdef CONFIG_X86_PAE pmds = (void *)linear - PAGE_SIZE; #endif - /* Linear mapping is easy: put every page's address into the - * mapping in order. */ + /* + * Linear mapping is easy: put every page's address into the + * mapping in order. + */ for (i = 0; i < mapped_pages; i++) { pte_t pte; pte = pfn_pte(i, __pgprot(_PAGE_PRESENT|_PAGE_RW|_PAGE_USER)); @@ -848,8 +957,10 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } - /* The top level points to the linear page table pages above. - * We setup the identity and linear mappings here. */ + /* + * The top level points to the linear page table pages above. + * We setup the identity and linear mappings here. + */ #ifdef CONFIG_X86_PAE for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD; i += PTRS_PER_PTE, j++) { @@ -880,15 +991,19 @@ static unsigned long setup_pagetables(struct lguest *lg, } #endif - /* We return the top level (guest-physical) address: remember where - * this is. */ + /* + * We return the top level (guest-physical) address: remember where + * this is. + */ return (unsigned long)pgdir - mem_base; } -/*H:500 (vii) Setting up the page tables initially. +/*H:500 + * (vii) Setting up the page tables initially. * * When a Guest is first created, the Launcher tells us where the toplevel of - * its first page table is. We set some things up here: */ + * its first page table is. We set some things up here: + */ int init_guest_pagetable(struct lguest *lg) { u64 mem; @@ -898,14 +1013,18 @@ int init_guest_pagetable(struct lguest *lg) pgd_t *pgd; pmd_t *pmd_table; #endif - /* Get the Guest memory size and the ramdisk size from the boot header - * located at lg->mem_base (Guest address 0). */ + /* + * Get the Guest memory size and the ramdisk size from the boot header + * located at lg->mem_base (Guest address 0). + */ if (copy_from_user(&mem, &boot->e820_map[0].size, sizeof(mem)) || get_user(initrd_size, &boot->hdr.ramdisk_size)) return -EFAULT; - /* We start on the first shadow page table, and give it a blank PGD - * page. */ + /* + * We start on the first shadow page table, and give it a blank PGD + * page. + */ lg->pgdirs[0].gpgdir = setup_pagetables(lg, mem, initrd_size); if (IS_ERR_VALUE(lg->pgdirs[0].gpgdir)) return lg->pgdirs[0].gpgdir; @@ -931,17 +1050,21 @@ void page_table_guest_data_init(struct lg_cpu *cpu) /* We get the kernel address: above this is all kernel memory. */ if (get_user(cpu->lg->kernel_address, &cpu->lg->lguest_data->kernel_address) - /* We tell the Guest that it can't use the top 2 or 4 MB - * of virtual addresses used by the Switcher. */ + /* + * We tell the Guest that it can't use the top 2 or 4 MB + * of virtual addresses used by the Switcher. + */ || put_user(RESERVE_MEM * 1024 * 1024, &cpu->lg->lguest_data->reserve_mem) || put_user(cpu->lg->pgdirs[0].gpgdir, &cpu->lg->lguest_data->pgdir)) kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data); - /* In flush_user_mappings() we loop from 0 to + /* + * In flush_user_mappings() we loop from 0 to * "pgd_index(lg->kernel_address)". This assumes it won't hit the - * Switcher mappings, so check that now. */ + * Switcher mappings, so check that now. + */ #ifdef CONFIG_X86_PAE if (pgd_index(cpu->lg->kernel_address) == SWITCHER_PGD_INDEX && pmd_index(cpu->lg->kernel_address) == SWITCHER_PMD_INDEX) @@ -964,12 +1087,14 @@ void free_guest_pagetable(struct lguest *lg) free_page((long)lg->pgdirs[i].pgdir); } -/*H:480 (vi) Mapping the Switcher when the Guest is about to run. +/*H:480 + * (vi) Mapping the Switcher when the Guest is about to run. * * The Switcher and the two pages for this CPU need to be visible in the * Guest (and not the pages for other CPUs). We have the appropriate PTE pages * for each CPU already set up, we just need to hook them in now we know which - * Guest is about to run on this CPU. */ + * Guest is about to run on this CPU. + */ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) { pte_t *switcher_pte_page = __get_cpu_var(switcher_pte_pages); @@ -990,20 +1115,24 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) #else pgd_t switcher_pgd; - /* Make the last PGD entry for this Guest point to the Switcher's PTE - * page for this CPU (with appropriate flags). */ + /* + * Make the last PGD entry for this Guest point to the Switcher's PTE + * page for this CPU (with appropriate flags). + */ switcher_pgd = __pgd(__pa(switcher_pte_page) | __PAGE_KERNEL_EXEC); cpu->lg->pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX] = switcher_pgd; #endif - /* We also change the Switcher PTE page. When we're running the Guest, + /* + * We also change the Switcher PTE page. When we're running the Guest, * we want the Guest's "regs" page to appear where the first Switcher * page for this CPU is. This is an optimization: when the Switcher * saves the Guest registers, it saves them into the first page of this * CPU's "struct lguest_pages": if we make sure the Guest's register * page is already mapped there, we don't have to copy them out - * again. */ + * again. + */ pfn = __pa(cpu->regs_page) >> PAGE_SHIFT; native_set_pte(®s_pte, pfn_pte(pfn, PAGE_KERNEL)); native_set_pte(&switcher_pte_page[pte_index((unsigned long)pages)], @@ -1019,10 +1148,12 @@ static void free_switcher_pte_pages(void) free_page((long)switcher_pte_page(i)); } -/*H:520 Setting up the Switcher PTE page for given CPU is fairly easy, given +/*H:520 + * Setting up the Switcher PTE page for given CPU is fairly easy, given * the CPU number and the "struct page"s for the Switcher code itself. * - * Currently the Switcher is less than a page long, so "pages" is always 1. */ + * Currently the Switcher is less than a page long, so "pages" is always 1. + */ static __init void populate_switcher_pte_page(unsigned int cpu, struct page *switcher_page[], unsigned int pages) @@ -1043,13 +1174,16 @@ static __init void populate_switcher_pte_page(unsigned int cpu, native_set_pte(&pte[i], pfn_pte(page_to_pfn(switcher_page[i]), __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED|_PAGE_RW))); - /* The second page contains the "struct lguest_ro_state", and is - * read-only. */ + /* + * The second page contains the "struct lguest_ro_state", and is + * read-only. + */ native_set_pte(&pte[i+1], pfn_pte(page_to_pfn(switcher_page[i+1]), __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED))); } -/* We've made it through the page table code. Perhaps our tired brains are +/* + * We've made it through the page table code. Perhaps our tired brains are * still processing the details, or perhaps we're simply glad it's over. * * If nothing else, note that all this complexity in juggling shadow page tables @@ -1058,10 +1192,13 @@ static __init void populate_switcher_pte_page(unsigned int cpu, * uses exotic direct Guest pagetable manipulation, and why both Intel and AMD * have implemented shadow page table support directly into hardware. * - * There is just one file remaining in the Host. */ + * There is just one file remaining in the Host. + */ -/*H:510 At boot or module load time, init_pagetables() allocates and populates - * the Switcher PTE page for each CPU. */ +/*H:510 + * At boot or module load time, init_pagetables() allocates and populates + * the Switcher PTE page for each CPU. + */ __init int init_pagetables(struct page **switcher_page, unsigned int pages) { unsigned int i; diff --git a/drivers/lguest/segments.c b/drivers/lguest/segments.c index 482ed5a18750..951c57b0a7e0 100644 --- a/drivers/lguest/segments.c +++ b/drivers/lguest/segments.c @@ -1,4 +1,5 @@ -/*P:600 The x86 architecture has segments, which involve a table of descriptors +/*P:600 + * The x86 architecture has segments, which involve a table of descriptors * which can be used to do funky things with virtual address interpretation. * We originally used to use segments so the Guest couldn't alter the * Guest<->Host Switcher, and then we had to trim Guest segments, and restore @@ -8,7 +9,8 @@ * * In these modern times, the segment handling code consists of simple sanity * checks, and the worst you'll experience reading this code is butterfly-rash - * from frolicking through its parklike serenity. :*/ + * from frolicking through its parklike serenity. +:*/ #include "lg.h" /*H:600 @@ -41,10 +43,12 @@ * begin. */ -/* There are several entries we don't let the Guest set. The TSS entry is the +/* + * There are several entries we don't let the Guest set. The TSS entry is the * "Task State Segment" which controls all kinds of delicate things. The * LGUEST_CS and LGUEST_DS entries are reserved for the Switcher, and the - * the Guest can't be trusted to deal with double faults. */ + * the Guest can't be trusted to deal with double faults. + */ static bool ignored_gdt(unsigned int num) { return (num == GDT_ENTRY_TSS @@ -53,42 +57,52 @@ static bool ignored_gdt(unsigned int num) || num == GDT_ENTRY_DOUBLEFAULT_TSS); } -/*H:630 Once the Guest gave us new GDT entries, we fix them up a little. We +/*H:630 + * Once the Guest gave us new GDT entries, we fix them up a little. We * don't care if they're invalid: the worst that can happen is a General * Protection Fault in the Switcher when it restores a Guest segment register * which tries to use that entry. Then we kill the Guest for causing such a - * mess: the message will be "unhandled trap 256". */ + * mess: the message will be "unhandled trap 256". + */ static void fixup_gdt_table(struct lg_cpu *cpu, unsigned start, unsigned end) { unsigned int i; for (i = start; i < end; i++) { - /* We never copy these ones to real GDT, so we don't care what - * they say */ + /* + * We never copy these ones to real GDT, so we don't care what + * they say + */ if (ignored_gdt(i)) continue; - /* Segment descriptors contain a privilege level: the Guest is + /* + * Segment descriptors contain a privilege level: the Guest is * sometimes careless and leaves this as 0, even though it's - * running at privilege level 1. If so, we fix it here. */ + * running at privilege level 1. If so, we fix it here. + */ if ((cpu->arch.gdt[i].b & 0x00006000) == 0) cpu->arch.gdt[i].b |= (GUEST_PL << 13); - /* Each descriptor has an "accessed" bit. If we don't set it + /* + * Each descriptor has an "accessed" bit. If we don't set it * now, the CPU will try to set it when the Guest first loads * that entry into a segment register. But the GDT isn't - * writable by the Guest, so bad things can happen. */ + * writable by the Guest, so bad things can happen. + */ cpu->arch.gdt[i].b |= 0x00000100; } } -/*H:610 Like the IDT, we never simply use the GDT the Guest gives us. We keep +/*H:610 + * Like the IDT, we never simply use the GDT the Guest gives us. We keep * a GDT for each CPU, and copy across the Guest's entries each time we want to * run the Guest on that CPU. * * This routine is called at boot or modprobe time for each CPU to set up the * constant GDT entries: the ones which are the same no matter what Guest we're - * running. */ + * running. + */ void setup_default_gdt_entries(struct lguest_ro_state *state) { struct desc_struct *gdt = state->guest_gdt; @@ -98,30 +112,37 @@ void setup_default_gdt_entries(struct lguest_ro_state *state) gdt[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT; gdt[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT; - /* The TSS segment refers to the TSS entry for this particular CPU. + /* + * The TSS segment refers to the TSS entry for this particular CPU. * Forgive the magic flags: the 0x8900 means the entry is Present, it's * privilege level 0 Available 386 TSS system segment, and the 0x67 - * means Saturn is eclipsed by Mercury in the twelfth house. */ + * means Saturn is eclipsed by Mercury in the twelfth house. + */ gdt[GDT_ENTRY_TSS].a = 0x00000067 | (tss << 16); gdt[GDT_ENTRY_TSS].b = 0x00008900 | (tss & 0xFF000000) | ((tss >> 16) & 0x000000FF); } -/* This routine sets up the initial Guest GDT for booting. All entries start - * as 0 (unusable). */ +/* + * This routine sets up the initial Guest GDT for booting. All entries start + * as 0 (unusable). + */ void setup_guest_gdt(struct lg_cpu *cpu) { - /* Start with full 0-4G segments... */ + /* + * Start with full 0-4G segments...except the Guest is allowed to use + * them, so set the privilege level appropriately in the flags. + */ cpu->arch.gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT; cpu->arch.gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT; - /* ...except the Guest is allowed to use them, so set the privilege - * level appropriately in the flags. */ cpu->arch.gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13); cpu->arch.gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13); } -/*H:650 An optimization of copy_gdt(), for just the three "thead-local storage" - * entries. */ +/*H:650 + * An optimization of copy_gdt(), for just the three "thead-local storage" + * entries. + */ void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt) { unsigned int i; @@ -130,26 +151,34 @@ void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt) gdt[i] = cpu->arch.gdt[i]; } -/*H:640 When the Guest is run on a different CPU, or the GDT entries have - * changed, copy_gdt() is called to copy the Guest's GDT entries across to this - * CPU's GDT. */ +/*H:640 + * When the Guest is run on a different CPU, or the GDT entries have changed, + * copy_gdt() is called to copy the Guest's GDT entries across to this CPU's + * GDT. + */ void copy_gdt(const struct lg_cpu *cpu, struct desc_struct *gdt) { unsigned int i; - /* The default entries from setup_default_gdt_entries() are not - * replaced. See ignored_gdt() above. */ + /* + * The default entries from setup_default_gdt_entries() are not + * replaced. See ignored_gdt() above. + */ for (i = 0; i < GDT_ENTRIES; i++) if (!ignored_gdt(i)) gdt[i] = cpu->arch.gdt[i]; } -/*H:620 This is where the Guest asks us to load a new GDT entry - * (LHCALL_LOAD_GDT_ENTRY). We tweak the entry and copy it in. */ +/*H:620 + * This is where the Guest asks us to load a new GDT entry + * (LHCALL_LOAD_GDT_ENTRY). We tweak the entry and copy it in. + */ void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi) { - /* We assume the Guest has the same number of GDT entries as the - * Host, otherwise we'd have to dynamically allocate the Guest GDT. */ + /* + * We assume the Guest has the same number of GDT entries as the + * Host, otherwise we'd have to dynamically allocate the Guest GDT. + */ if (num >= ARRAY_SIZE(cpu->arch.gdt)) kill_guest(cpu, "too many gdt entries %i", num); @@ -157,15 +186,19 @@ void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi) cpu->arch.gdt[num].a = lo; cpu->arch.gdt[num].b = hi; fixup_gdt_table(cpu, num, num+1); - /* Mark that the GDT changed so the core knows it has to copy it again, - * even if the Guest is run on the same CPU. */ + /* + * Mark that the GDT changed so the core knows it has to copy it again, + * even if the Guest is run on the same CPU. + */ cpu->changed |= CHANGED_GDT; } -/* This is the fast-track version for just changing the three TLS entries. +/* + * This is the fast-track version for just changing the three TLS entries. * Remember that this happens on every context switch, so it's worth * optimizing. But wouldn't it be neater to have a single hypercall to cover - * both cases? */ + * both cases? + */ void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls) { struct desc_struct *tls = &cpu->arch.gdt[GDT_ENTRY_TLS_MIN]; @@ -175,7 +208,6 @@ void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls) /* Note that just the TLS entries have changed. */ cpu->changed |= CHANGED_GDT_TLS; } -/*:*/ /*H:660 * With this, we have finished the Host. diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c index eaf722fe309a..96f7d88ec7f8 100644 --- a/drivers/lguest/x86/core.c +++ b/drivers/lguest/x86/core.c @@ -17,13 +17,15 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -/*P:450 This file contains the x86-specific lguest code. It used to be all +/*P:450 + * This file contains the x86-specific lguest code. It used to be all * mixed in with drivers/lguest/core.c but several foolhardy code slashers * wrestled most of the dependencies out to here in preparation for porting * lguest to other architectures (see what I mean by foolhardy?). * * This also contains a couple of non-obvious setup and teardown pieces which - * were implemented after days of debugging pain. :*/ + * were implemented after days of debugging pain. +:*/ #include #include #include @@ -82,25 +84,33 @@ static DEFINE_PER_CPU(struct lg_cpu *, last_cpu); */ static void copy_in_guest_info(struct lg_cpu *cpu, struct lguest_pages *pages) { - /* Copying all this data can be quite expensive. We usually run the + /* + * Copying all this data can be quite expensive. We usually run the * same Guest we ran last time (and that Guest hasn't run anywhere else * meanwhile). If that's not the case, we pretend everything in the - * Guest has changed. */ + * Guest has changed. + */ if (__get_cpu_var(last_cpu) != cpu || cpu->last_pages != pages) { __get_cpu_var(last_cpu) = cpu; cpu->last_pages = pages; cpu->changed = CHANGED_ALL; } - /* These copies are pretty cheap, so we do them unconditionally: */ - /* Save the current Host top-level page directory. */ + /* + * These copies are pretty cheap, so we do them unconditionally: */ + /* Save the current Host top-level page directory. + */ pages->state.host_cr3 = __pa(current->mm->pgd); - /* Set up the Guest's page tables to see this CPU's pages (and no - * other CPU's pages). */ + /* + * Set up the Guest's page tables to see this CPU's pages (and no + * other CPU's pages). + */ map_switcher_in_guest(cpu, pages); - /* Set up the two "TSS" members which tell the CPU what stack to use + /* + * Set up the two "TSS" members which tell the CPU what stack to use * for traps which do directly into the Guest (ie. traps at privilege - * level 1). */ + * level 1). + */ pages->state.guest_tss.sp1 = cpu->esp1; pages->state.guest_tss.ss1 = cpu->ss1; @@ -125,40 +135,53 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) /* This is a dummy value we need for GCC's sake. */ unsigned int clobber; - /* Copy the guest-specific information into this CPU's "struct - * lguest_pages". */ + /* + * Copy the guest-specific information into this CPU's "struct + * lguest_pages". + */ copy_in_guest_info(cpu, pages); - /* Set the trap number to 256 (impossible value). If we fault while + /* + * Set the trap number to 256 (impossible value). If we fault while * switching to the Guest (bad segment registers or bug), this will - * cause us to abort the Guest. */ + * cause us to abort the Guest. + */ cpu->regs->trapnum = 256; - /* Now: we push the "eflags" register on the stack, then do an "lcall". + /* + * Now: we push the "eflags" register on the stack, then do an "lcall". * This is how we change from using the kernel code segment to using * the dedicated lguest code segment, as well as jumping into the * Switcher. * * The lcall also pushes the old code segment (KERNEL_CS) onto the * stack, then the address of this call. This stack layout happens to - * exactly match the stack layout created by an interrupt... */ + * exactly match the stack layout created by an interrupt... + */ asm volatile("pushf; lcall *lguest_entry" - /* This is how we tell GCC that %eax ("a") and %ebx ("b") - * are changed by this routine. The "=" means output. */ + /* + * This is how we tell GCC that %eax ("a") and %ebx ("b") + * are changed by this routine. The "=" means output. + */ : "=a"(clobber), "=b"(clobber) - /* %eax contains the pages pointer. ("0" refers to the + /* + * %eax contains the pages pointer. ("0" refers to the * 0-th argument above, ie "a"). %ebx contains the * physical address of the Guest's top-level page - * directory. */ + * directory. + */ : "0"(pages), "1"(__pa(cpu->lg->pgdirs[cpu->cpu_pgd].pgdir)) - /* We tell gcc that all these registers could change, + /* + * We tell gcc that all these registers could change, * which means we don't have to save and restore them in - * the Switcher. */ + * the Switcher. + */ : "memory", "%edx", "%ecx", "%edi", "%esi"); } /*:*/ -/*M:002 There are hooks in the scheduler which we can register to tell when we +/*M:002 + * There are hooks in the scheduler which we can register to tell when we * get kicked off the CPU (preempt_notifier_register()). This would allow us * to lazily disable SYSENTER which would regain some performance, and should * also simplify copy_in_guest_info(). Note that we'd still need to restore @@ -166,56 +189,72 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) * * We could also try using this hooks for PGE, but that might be too expensive. * - * The hooks were designed for KVM, but we can also put them to good use. :*/ + * The hooks were designed for KVM, but we can also put them to good use. +:*/ -/*H:040 This is the i386-specific code to setup and run the Guest. Interrupts - * are disabled: we own the CPU. */ +/*H:040 + * This is the i386-specific code to setup and run the Guest. Interrupts + * are disabled: we own the CPU. + */ void lguest_arch_run_guest(struct lg_cpu *cpu) { - /* Remember the awfully-named TS bit? If the Guest has asked to set it + /* + * Remember the awfully-named TS bit? If the Guest has asked to set it * we set it now, so we can trap and pass that trap to the Guest if it - * uses the FPU. */ + * uses the FPU. + */ if (cpu->ts) unlazy_fpu(current); - /* SYSENTER is an optimized way of doing system calls. We can't allow + /* + * SYSENTER is an optimized way of doing system calls. We can't allow * it because it always jumps to privilege level 0. A normal Guest * won't try it because we don't advertise it in CPUID, but a malicious * Guest (or malicious Guest userspace program) could, so we tell the - * CPU to disable it before running the Guest. */ + * CPU to disable it before running the Guest. + */ if (boot_cpu_has(X86_FEATURE_SEP)) wrmsr(MSR_IA32_SYSENTER_CS, 0, 0); - /* Now we actually run the Guest. It will return when something + /* + * Now we actually run the Guest. It will return when something * interesting happens, and we can examine its registers to see what it - * was doing. */ + * was doing. + */ run_guest_once(cpu, lguest_pages(raw_smp_processor_id())); - /* Note that the "regs" structure contains two extra entries which are + /* + * Note that the "regs" structure contains two extra entries which are * not really registers: a trap number which says what interrupt or * trap made the switcher code come back, and an error code which some - * traps set. */ + * traps set. + */ /* Restore SYSENTER if it's supposed to be on. */ if (boot_cpu_has(X86_FEATURE_SEP)) wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0); - /* If the Guest page faulted, then the cr2 register will tell us the + /* + * If the Guest page faulted, then the cr2 register will tell us the * bad virtual address. We have to grab this now, because once we * re-enable interrupts an interrupt could fault and thus overwrite - * cr2, or we could even move off to a different CPU. */ + * cr2, or we could even move off to a different CPU. + */ if (cpu->regs->trapnum == 14) cpu->arch.last_pagefault = read_cr2(); - /* Similarly, if we took a trap because the Guest used the FPU, + /* + * Similarly, if we took a trap because the Guest used the FPU, * we have to restore the FPU it expects to see. * math_state_restore() may sleep and we may even move off to * a different CPU. So all the critical stuff should be done - * before this. */ + * before this. + */ else if (cpu->regs->trapnum == 7) math_state_restore(); } -/*H:130 Now we've examined the hypercall code; our Guest can make requests. +/*H:130 + * Now we've examined the hypercall code; our Guest can make requests. * Our Guest is usually so well behaved; it never tries to do things it isn't * allowed to, and uses hypercalls instead. Unfortunately, Linux's paravirtual * infrastructure isn't quite complete, because it doesn't contain replacements @@ -225,26 +264,33 @@ void lguest_arch_run_guest(struct lg_cpu *cpu) * * When the Guest uses one of these instructions, we get a trap (General * Protection Fault) and come here. We see if it's one of those troublesome - * instructions and skip over it. We return true if we did. */ + * instructions and skip over it. We return true if we did. + */ static int emulate_insn(struct lg_cpu *cpu) { u8 insn; unsigned int insnlen = 0, in = 0, shift = 0; - /* The eip contains the *virtual* address of the Guest's instruction: - * guest_pa just subtracts the Guest's page_offset. */ + /* + * The eip contains the *virtual* address of the Guest's instruction: + * guest_pa just subtracts the Guest's page_offset. + */ unsigned long physaddr = guest_pa(cpu, cpu->regs->eip); - /* This must be the Guest kernel trying to do something, not userspace! + /* + * This must be the Guest kernel trying to do something, not userspace! * The bottom two bits of the CS segment register are the privilege - * level. */ + * level. + */ if ((cpu->regs->cs & 3) != GUEST_PL) return 0; /* Decoding x86 instructions is icky. */ insn = lgread(cpu, physaddr, u8); - /* 0x66 is an "operand prefix". It means it's using the upper 16 bits - of the eax register. */ + /* + * 0x66 is an "operand prefix". It means it's using the upper 16 bits + * of the eax register. + */ if (insn == 0x66) { shift = 16; /* The instruction is 1 byte so far, read the next byte. */ @@ -252,8 +298,10 @@ static int emulate_insn(struct lg_cpu *cpu) insn = lgread(cpu, physaddr + insnlen, u8); } - /* We can ignore the lower bit for the moment and decode the 4 opcodes - * we need to emulate. */ + /* + * We can ignore the lower bit for the moment and decode the 4 opcodes + * we need to emulate. + */ switch (insn & 0xFE) { case 0xE4: /* in ,%al */ insnlen += 2; @@ -274,9 +322,11 @@ static int emulate_insn(struct lg_cpu *cpu) return 0; } - /* If it was an "IN" instruction, they expect the result to be read + /* + * If it was an "IN" instruction, they expect the result to be read * into %eax, so we change %eax. We always return all-ones, which - * traditionally means "there's nothing there". */ + * traditionally means "there's nothing there". + */ if (in) { /* Lower bit tells is whether it's a 16 or 32 bit access */ if (insn & 0x1) @@ -290,7 +340,8 @@ static int emulate_insn(struct lg_cpu *cpu) return 1; } -/* Our hypercalls mechanism used to be based on direct software interrupts. +/* + * Our hypercalls mechanism used to be based on direct software interrupts. * After Anthony's "Refactor hypercall infrastructure" kvm patch, we decided to * change over to using kvm hypercalls. * @@ -318,16 +369,20 @@ static int emulate_insn(struct lg_cpu *cpu) */ static void rewrite_hypercall(struct lg_cpu *cpu) { - /* This are the opcodes we use to patch the Guest. The opcode for "int + /* + * This are the opcodes we use to patch the Guest. The opcode for "int * $0x1f" is "0xcd 0x1f" but vmcall instruction is 3 bytes long, so we - * complete the sequence with a NOP (0x90). */ + * complete the sequence with a NOP (0x90). + */ u8 insn[3] = {0xcd, 0x1f, 0x90}; __lgwrite(cpu, guest_pa(cpu, cpu->regs->eip), insn, sizeof(insn)); - /* The above write might have caused a copy of that page to be made + /* + * The above write might have caused a copy of that page to be made * (if it was read-only). We need to make sure the Guest has * up-to-date pagetables. As this doesn't happen often, we can just - * drop them all. */ + * drop them all. + */ guest_pagetable_clear_all(cpu); } @@ -335,9 +390,11 @@ static bool is_hypercall(struct lg_cpu *cpu) { u8 insn[3]; - /* This must be the Guest kernel trying to do something. + /* + * This must be the Guest kernel trying to do something. * The bottom two bits of the CS segment register are the privilege - * level. */ + * level. + */ if ((cpu->regs->cs & 3) != GUEST_PL) return false; @@ -351,86 +408,105 @@ void lguest_arch_handle_trap(struct lg_cpu *cpu) { switch (cpu->regs->trapnum) { case 13: /* We've intercepted a General Protection Fault. */ - /* Check if this was one of those annoying IN or OUT + /* + * Check if this was one of those annoying IN or OUT * instructions which we need to emulate. If so, we just go - * back into the Guest after we've done it. */ + * back into the Guest after we've done it. + */ if (cpu->regs->errcode == 0) { if (emulate_insn(cpu)) return; } - /* If KVM is active, the vmcall instruction triggers a - * General Protection Fault. Normally it triggers an - * invalid opcode fault (6): */ + /* + * If KVM is active, the vmcall instruction triggers a General + * Protection Fault. Normally it triggers an invalid opcode + * fault (6): + */ case 6: - /* We need to check if ring == GUEST_PL and - * faulting instruction == vmcall. */ + /* + * We need to check if ring == GUEST_PL and faulting + * instruction == vmcall. + */ if (is_hypercall(cpu)) { rewrite_hypercall(cpu); return; } break; case 14: /* We've intercepted a Page Fault. */ - /* The Guest accessed a virtual address that wasn't mapped. + /* + * The Guest accessed a virtual address that wasn't mapped. * This happens a lot: we don't actually set up most of the page * tables for the Guest at all when we start: as it runs it asks * for more and more, and we set them up as required. In this * case, we don't even tell the Guest that the fault happened. * * The errcode tells whether this was a read or a write, and - * whether kernel or userspace code. */ + * whether kernel or userspace code. + */ if (demand_page(cpu, cpu->arch.last_pagefault, cpu->regs->errcode)) return; - /* OK, it's really not there (or not OK): the Guest needs to + /* + * OK, it's really not there (or not OK): the Guest needs to * know. We write out the cr2 value so it knows where the * fault occurred. * * Note that if the Guest were really messed up, this could * happen before it's done the LHCALL_LGUEST_INIT hypercall, so - * lg->lguest_data could be NULL */ + * lg->lguest_data could be NULL + */ if (cpu->lg->lguest_data && put_user(cpu->arch.last_pagefault, &cpu->lg->lguest_data->cr2)) kill_guest(cpu, "Writing cr2"); break; case 7: /* We've intercepted a Device Not Available fault. */ - /* If the Guest doesn't want to know, we already restored the - * Floating Point Unit, so we just continue without telling - * it. */ + /* + * If the Guest doesn't want to know, we already restored the + * Floating Point Unit, so we just continue without telling it. + */ if (!cpu->ts) return; break; case 32 ... 255: - /* These values mean a real interrupt occurred, in which case + /* + * These values mean a real interrupt occurred, in which case * the Host handler has already been run. We just do a * friendly check if another process should now be run, then - * return to run the Guest again */ + * return to run the Guest again + */ cond_resched(); return; case LGUEST_TRAP_ENTRY: - /* Our 'struct hcall_args' maps directly over our regs: we set - * up the pointer now to indicate a hypercall is pending. */ + /* + * Our 'struct hcall_args' maps directly over our regs: we set + * up the pointer now to indicate a hypercall is pending. + */ cpu->hcall = (struct hcall_args *)cpu->regs; return; } /* We didn't handle the trap, so it needs to go to the Guest. */ if (!deliver_trap(cpu, cpu->regs->trapnum)) - /* If the Guest doesn't have a handler (either it hasn't + /* + * If the Guest doesn't have a handler (either it hasn't * registered any yet, or it's one of the faults we don't let - * it handle), it dies with this cryptic error message. */ + * it handle), it dies with this cryptic error message. + */ kill_guest(cpu, "unhandled trap %li at %#lx (%#lx)", cpu->regs->trapnum, cpu->regs->eip, cpu->regs->trapnum == 14 ? cpu->arch.last_pagefault : cpu->regs->errcode); } -/* Now we can look at each of the routines this calls, in increasing order of +/* + * Now we can look at each of the routines this calls, in increasing order of * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(), * deliver_trap() and demand_page(). After all those, we'll be ready to * examine the Switcher, and our philosophical understanding of the Host/Guest - * duality will be complete. :*/ + * duality will be complete. +:*/ static void adjust_pge(void *on) { if (on) @@ -439,13 +515,16 @@ static void adjust_pge(void *on) write_cr4(read_cr4() & ~X86_CR4_PGE); } -/*H:020 Now the Switcher is mapped and every thing else is ready, we need to do - * some more i386-specific initialization. */ +/*H:020 + * Now the Switcher is mapped and every thing else is ready, we need to do + * some more i386-specific initialization. + */ void __init lguest_arch_host_init(void) { int i; - /* Most of the i386/switcher.S doesn't care that it's been moved; on + /* + * Most of the i386/switcher.S doesn't care that it's been moved; on * Intel, jumps are relative, and it doesn't access any references to * external code or data. * @@ -453,7 +532,8 @@ void __init lguest_arch_host_init(void) * addresses are placed in a table (default_idt_entries), so we need to * update the table with the new addresses. switcher_offset() is a * convenience function which returns the distance between the - * compiled-in switcher code and the high-mapped copy we just made. */ + * compiled-in switcher code and the high-mapped copy we just made. + */ for (i = 0; i < IDT_ENTRIES; i++) default_idt_entries[i] += switcher_offset(); @@ -468,63 +548,81 @@ void __init lguest_arch_host_init(void) for_each_possible_cpu(i) { /* lguest_pages() returns this CPU's two pages. */ struct lguest_pages *pages = lguest_pages(i); - /* This is a convenience pointer to make the code fit one - * statement to a line. */ + /* This is a convenience pointer to make the code neater. */ struct lguest_ro_state *state = &pages->state; - /* The Global Descriptor Table: the Host has a different one + /* + * The Global Descriptor Table: the Host has a different one * for each CPU. We keep a descriptor for the GDT which says * where it is and how big it is (the size is actually the last - * byte, not the size, hence the "-1"). */ + * byte, not the size, hence the "-1"). + */ state->host_gdt_desc.size = GDT_SIZE-1; state->host_gdt_desc.address = (long)get_cpu_gdt_table(i); - /* All CPUs on the Host use the same Interrupt Descriptor + /* + * All CPUs on the Host use the same Interrupt Descriptor * Table, so we just use store_idt(), which gets this CPU's IDT - * descriptor. */ + * descriptor. + */ store_idt(&state->host_idt_desc); - /* The descriptors for the Guest's GDT and IDT can be filled + /* + * The descriptors for the Guest's GDT and IDT can be filled * out now, too. We copy the GDT & IDT into ->guest_gdt and - * ->guest_idt before actually running the Guest. */ + * ->guest_idt before actually running the Guest. + */ state->guest_idt_desc.size = sizeof(state->guest_idt)-1; state->guest_idt_desc.address = (long)&state->guest_idt; state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1; state->guest_gdt_desc.address = (long)&state->guest_gdt; - /* We know where we want the stack to be when the Guest enters + /* + * We know where we want the stack to be when the Guest enters * the Switcher: in pages->regs. The stack grows upwards, so - * we start it at the end of that structure. */ + * we start it at the end of that structure. + */ state->guest_tss.sp0 = (long)(&pages->regs + 1); - /* And this is the GDT entry to use for the stack: we keep a - * couple of special LGUEST entries. */ + /* + * And this is the GDT entry to use for the stack: we keep a + * couple of special LGUEST entries. + */ state->guest_tss.ss0 = LGUEST_DS; - /* x86 can have a finegrained bitmap which indicates what I/O + /* + * x86 can have a finegrained bitmap which indicates what I/O * ports the process can use. We set it to the end of our - * structure, meaning "none". */ + * structure, meaning "none". + */ state->guest_tss.io_bitmap_base = sizeof(state->guest_tss); - /* Some GDT entries are the same across all Guests, so we can - * set them up now. */ + /* + * Some GDT entries are the same across all Guests, so we can + * set them up now. + */ setup_default_gdt_entries(state); /* Most IDT entries are the same for all Guests, too.*/ setup_default_idt_entries(state, default_idt_entries); - /* The Host needs to be able to use the LGUEST segments on this - * CPU, too, so put them in the Host GDT. */ + /* + * The Host needs to be able to use the LGUEST segments on this + * CPU, too, so put them in the Host GDT. + */ get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT; get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT; } - /* In the Switcher, we want the %cs segment register to use the + /* + * In the Switcher, we want the %cs segment register to use the * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so * it will be undisturbed when we switch. To change %cs and jump we - * need this structure to feed to Intel's "lcall" instruction. */ + * need this structure to feed to Intel's "lcall" instruction. + */ lguest_entry.offset = (long)switch_to_guest + switcher_offset(); lguest_entry.segment = LGUEST_CS; - /* Finally, we need to turn off "Page Global Enable". PGE is an + /* + * Finally, we need to turn off "Page Global Enable". PGE is an * optimization where page table entries are specially marked to show * they never change. The Host kernel marks all the kernel pages this * way because it's always present, even when userspace is running. @@ -534,16 +632,21 @@ void __init lguest_arch_host_init(void) * you'll get really weird bugs that you'll chase for two days. * * I used to turn PGE off every time we switched to the Guest and back - * on when we return, but that slowed the Switcher down noticibly. */ + * on when we return, but that slowed the Switcher down noticibly. + */ - /* We don't need the complexity of CPUs coming and going while we're - * doing this. */ + /* + * We don't need the complexity of CPUs coming and going while we're + * doing this. + */ get_online_cpus(); if (cpu_has_pge) { /* We have a broader idea of "global". */ /* Remember that this was originally set (for cleanup). */ cpu_had_pge = 1; - /* adjust_pge is a helper function which sets or unsets the PGE - * bit on its CPU, depending on the argument (0 == unset). */ + /* + * adjust_pge is a helper function which sets or unsets the PGE + * bit on its CPU, depending on the argument (0 == unset). + */ on_each_cpu(adjust_pge, (void *)0, 1); /* Turn off the feature in the global feature set. */ clear_cpu_cap(&boot_cpu_data, X86_FEATURE_PGE); @@ -590,26 +693,32 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu) { u32 tsc_speed; - /* The pointer to the Guest's "struct lguest_data" is the only argument. - * We check that address now. */ + /* + * The pointer to the Guest's "struct lguest_data" is the only argument. + * We check that address now. + */ if (!lguest_address_ok(cpu->lg, cpu->hcall->arg1, sizeof(*cpu->lg->lguest_data))) return -EFAULT; - /* Having checked it, we simply set lg->lguest_data to point straight + /* + * Having checked it, we simply set lg->lguest_data to point straight * into the Launcher's memory at the right place and then use * copy_to_user/from_user from now on, instead of lgread/write. I put * this in to show that I'm not immune to writing stupid - * optimizations. */ + * optimizations. + */ cpu->lg->lguest_data = cpu->lg->mem_base + cpu->hcall->arg1; - /* We insist that the Time Stamp Counter exist and doesn't change with + /* + * We insist that the Time Stamp Counter exist and doesn't change with * cpu frequency. Some devious chip manufacturers decided that TSC * changes could be handled in software. I decided that time going * backwards might be good for benchmarks, but it's bad for users. * * We also insist that the TSC be stable: the kernel detects unreliable - * TSCs for its own purposes, and we use that here. */ + * TSCs for its own purposes, and we use that here. + */ if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC) && !check_tsc_unstable()) tsc_speed = tsc_khz; else @@ -625,38 +734,47 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu) } /*:*/ -/*L:030 lguest_arch_setup_regs() +/*L:030 + * lguest_arch_setup_regs() * * Most of the Guest's registers are left alone: we used get_zeroed_page() to - * allocate the structure, so they will be 0. */ + * allocate the structure, so they will be 0. + */ void lguest_arch_setup_regs(struct lg_cpu *cpu, unsigned long start) { struct lguest_regs *regs = cpu->regs; - /* There are four "segment" registers which the Guest needs to boot: + /* + * There are four "segment" registers which the Guest needs to boot: * The "code segment" register (cs) refers to the kernel code segment * __KERNEL_CS, and the "data", "extra" and "stack" segment registers * refer to the kernel data segment __KERNEL_DS. * * The privilege level is packed into the lower bits. The Guest runs - * at privilege level 1 (GUEST_PL).*/ + * at privilege level 1 (GUEST_PL). + */ regs->ds = regs->es = regs->ss = __KERNEL_DS|GUEST_PL; regs->cs = __KERNEL_CS|GUEST_PL; - /* The "eflags" register contains miscellaneous flags. Bit 1 (0x002) + /* + * The "eflags" register contains miscellaneous flags. Bit 1 (0x002) * is supposed to always be "1". Bit 9 (0x200) controls whether * interrupts are enabled. We always leave interrupts enabled while - * running the Guest. */ + * running the Guest. + */ regs->eflags = X86_EFLAGS_IF | 0x2; - /* The "Extended Instruction Pointer" register says where the Guest is - * running. */ + /* + * The "Extended Instruction Pointer" register says where the Guest is + * running. + */ regs->eip = start; - /* %esi points to our boot information, at physical address 0, so don't - * touch it. */ + /* + * %esi points to our boot information, at physical address 0, so don't + * touch it. + */ - /* There are a couple of GDT entries the Guest expects when first - * booting. */ + /* There are a couple of GDT entries the Guest expects at boot. */ setup_guest_gdt(cpu); } diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S index 3fc15318a80f..6dec09793836 100644 --- a/drivers/lguest/x86/switcher_32.S +++ b/drivers/lguest/x86/switcher_32.S @@ -1,12 +1,15 @@ -/*P:900 This is the Switcher: code which sits at 0xFFC00000 astride both the +/*P:900 + * This is the Switcher: code which sits at 0xFFC00000 astride both the * Host and Guest to do the low-level Guest<->Host switch. It is as simple as * it can be made, but it's naturally very specific to x86. * * You have now completed Preparation. If this has whet your appetite; if you * are feeling invigorated and refreshed then the next, more challenging stage - * can be found in "make Guest". :*/ + * can be found in "make Guest". + :*/ -/*M:012 Lguest is meant to be simple: my rule of thumb is that 1% more LOC must +/*M:012 + * Lguest is meant to be simple: my rule of thumb is that 1% more LOC must * gain at least 1% more performance. Since neither LOC nor performance can be * measured beforehand, it generally means implementing a feature then deciding * if it's worth it. And once it's implemented, who can say no? @@ -31,11 +34,14 @@ * Host (which is actually really easy). * * Two questions remain. Would the performance gain outweigh the complexity? - * And who would write the verse documenting it? :*/ + * And who would write the verse documenting it? +:*/ -/*M:011 Lguest64 handles NMI. This gave me NMI envy (until I looked at their +/*M:011 + * Lguest64 handles NMI. This gave me NMI envy (until I looked at their * code). It's worth doing though, since it would let us use oprofile in the - * Host when a Guest is running. :*/ + * Host when a Guest is running. +:*/ /*S:100 * Welcome to the Switcher itself! diff --git a/include/linux/lguest.h b/include/linux/lguest.h index dbf2479e808e..0a3a11afd64b 100644 --- a/include/linux/lguest.h +++ b/include/linux/lguest.h @@ -1,5 +1,7 @@ -/* Things the lguest guest needs to know. Note: like all lguest interfaces, - * this is subject to wild and random change between versions. */ +/* + * Things the lguest guest needs to know. Note: like all lguest interfaces, + * this is subject to wild and random change between versions. + */ #ifndef _LINUX_LGUEST_H #define _LINUX_LGUEST_H @@ -11,32 +13,42 @@ #define LG_CLOCK_MIN_DELTA 100UL #define LG_CLOCK_MAX_DELTA ULONG_MAX -/*G:031 The second method of communicating with the Host is to via "struct +/*G:031 + * The second method of communicating with the Host is to via "struct * lguest_data". Once the Guest's initialization hypercall tells the Host where - * this is, the Guest and Host both publish information in it. :*/ + * this is, the Guest and Host both publish information in it. +:*/ struct lguest_data { - /* 512 == enabled (same as eflags in normal hardware). The Guest - * changes interrupts so often that a hypercall is too slow. */ + /* + * 512 == enabled (same as eflags in normal hardware). The Guest + * changes interrupts so often that a hypercall is too slow. + */ unsigned int irq_enabled; /* Fine-grained interrupt disabling by the Guest */ DECLARE_BITMAP(blocked_interrupts, LGUEST_IRQS); - /* The Host writes the virtual address of the last page fault here, + /* + * The Host writes the virtual address of the last page fault here, * which saves the Guest a hypercall. CR2 is the native register where - * this address would normally be found. */ + * this address would normally be found. + */ unsigned long cr2; /* Wallclock time set by the Host. */ struct timespec time; - /* Interrupt pending set by the Host. The Guest should do a hypercall - * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF). */ + /* + * Interrupt pending set by the Host. The Guest should do a hypercall + * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF). + */ int irq_pending; - /* Async hypercall ring. Instead of directly making hypercalls, we can + /* + * Async hypercall ring. Instead of directly making hypercalls, we can * place them in here for processing the next time the Host wants. - * This batching can be quite efficient. */ + * This batching can be quite efficient. + */ /* 0xFF == done (set by Host), 0 == pending (set by Guest). */ u8 hcall_status[LHCALL_RING_SIZE]; diff --git a/include/linux/lguest_launcher.h b/include/linux/lguest_launcher.h index bfefbdf7498a..495203ff221c 100644 --- a/include/linux/lguest_launcher.h +++ b/include/linux/lguest_launcher.h @@ -29,8 +29,10 @@ struct lguest_device_desc { __u8 type; /* The number of virtqueues (first in config array) */ __u8 num_vq; - /* The number of bytes of feature bits. Multiply by 2: one for host - * features and one for Guest acknowledgements. */ + /* + * The number of bytes of feature bits. Multiply by 2: one for host + * features and one for Guest acknowledgements. + */ __u8 feature_len; /* The number of bytes of the config array after virtqueues. */ __u8 config_len; @@ -39,8 +41,10 @@ struct lguest_device_desc { __u8 config[0]; }; -/*D:135 This is how we expect the device configuration field for a virtqueue - * to be laid out in config space. */ +/*D:135 + * This is how we expect the device configuration field for a virtqueue + * to be laid out in config space. + */ struct lguest_vqconfig { /* The number of entries in the virtio_ring */ __u16 num; @@ -61,7 +65,9 @@ enum lguest_req LHREQ_EVENTFD, /* + address, fd. */ }; -/* The alignment to use between consumer and producer parts of vring. - * x86 pagesize for historical reasons. */ +/* + * The alignment to use between consumer and producer parts of vring. + * x86 pagesize for historical reasons. + */ #define LGUEST_VRING_ALIGN 4096 #endif /* _LINUX_LGUEST_LAUNCHER */ -- cgit v1.2.3 From a91d74a3c4de8115295ee87350c13a329164aaaf Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:45 -0600 Subject: lguest: update commentry Every so often, after code shuffles, I need to go through and unbitrot the Lguest Journey (see drivers/lguest/README). Since we now use RCU in a simple form in one place I took the opportunity to expand that explanation. Signed-off-by: Rusty Russell Cc: Ingo Molnar Cc: Paul McKenney --- Documentation/lguest/lguest.c | 184 +++++++++++++++++++++++++++--------- arch/x86/include/asm/lguest_hcall.h | 8 +- arch/x86/lguest/boot.c | 99 ++++++++++++++----- arch/x86/lguest/i386_head.S | 2 + drivers/lguest/core.c | 7 +- drivers/lguest/hypercalls.c | 6 +- drivers/lguest/lguest_device.c | 11 ++- drivers/lguest/lguest_user.c | 100 ++++++++++++++++++-- drivers/lguest/page_tables.c | 84 ++++++++++++---- drivers/lguest/x86/core.c | 2 +- drivers/lguest/x86/switcher_32.S | 6 +- 11 files changed, 398 insertions(+), 111 deletions(-) (limited to 'drivers') diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index aa66a52b73e9..45163651b519 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -49,7 +49,7 @@ #include "linux/virtio_ring.h" #include "asm/bootparam.h" /*L:110 - * We can ignore the 39 include files we need for this program, but I do want + * We can ignore the 42 include files we need for this program, but I do want * to draw attention to the use of kernel-style types. * * As Linus said, "C is a Spartan language, and so should your naming be." I @@ -305,6 +305,11 @@ static void *map_zeroed_pages(unsigned int num) PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0); if (addr == MAP_FAILED) err(1, "Mmaping %u pages of /dev/zero", num); + + /* + * One neat mmap feature is that you can close the fd, and it + * stays mapped. + */ close(fd); return addr; @@ -557,7 +562,7 @@ static void tell_kernel(unsigned long start) } /*:*/ -/* +/*L:200 * Device Handling. * * When the Guest gives us a buffer, it sends an array of addresses and sizes. @@ -608,7 +613,10 @@ static unsigned next_desc(struct vring_desc *desc, return next; } -/* This actually sends the interrupt for this virtqueue */ +/* + * This actually sends the interrupt for this virtqueue, if we've used a + * buffer. + */ static void trigger_irq(struct virtqueue *vq) { unsigned long buf[] = { LHREQ_IRQ, vq->config.irq }; @@ -629,12 +637,12 @@ static void trigger_irq(struct virtqueue *vq) } /* - * This looks in the virtqueue and for the first available buffer, and converts + * This looks in the virtqueue for the first available buffer, and converts * it to an iovec for convenient access. Since descriptors consist of some * number of output then some number of input descriptors, it's actually two * iovecs, but we pack them into one and note how many of each there were. * - * This function returns the descriptor number found. + * This function waits if necessary, and returns the descriptor number found. */ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct iovec iov[], @@ -644,10 +652,14 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, struct vring_desc *desc; u16 last_avail = lg_last_avail(vq); + /* There's nothing available? */ while (last_avail == vq->vring.avail->idx) { u64 event; - /* OK, tell Guest about progress up to now. */ + /* + * Since we're about to sleep, now is a good time to tell the + * Guest about what we've used up to now. + */ trigger_irq(vq); /* OK, now we need to know about added descriptors. */ @@ -734,8 +746,9 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq, } /* - * After we've used one of their buffers, we tell them about it. We'll then - * want to send them an interrupt, using trigger_irq(). + * After we've used one of their buffers, we tell the Guest about it. Sometime + * later we'll want to send them an interrupt using trigger_irq(); note that + * wait_for_vq_desc() does that for us if it has to wait. */ static void add_used(struct virtqueue *vq, unsigned int head, int len) { @@ -782,12 +795,12 @@ static void console_input(struct virtqueue *vq) struct console_abort *abort = vq->dev->priv; struct iovec iov[vq->vring.num]; - /* Make sure there's a descriptor waiting. */ + /* Make sure there's a descriptor available. */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); if (out_num) errx(1, "Output buffers in console in queue?"); - /* Read it in. */ + /* Read into it. This is where we usually wait. */ len = readv(STDIN_FILENO, iov, in_num); if (len <= 0) { /* Ran out of input? */ @@ -800,6 +813,7 @@ static void console_input(struct virtqueue *vq) pause(); } + /* Tell the Guest we used a buffer. */ add_used_and_trigger(vq, head, len); /* @@ -834,15 +848,23 @@ static void console_output(struct virtqueue *vq) unsigned int head, out, in; struct iovec iov[vq->vring.num]; + /* We usually wait in here, for the Guest to give us something. */ head = wait_for_vq_desc(vq, iov, &out, &in); if (in) errx(1, "Input buffers in console output queue?"); + + /* writev can return a partial write, so we loop here. */ while (!iov_empty(iov, out)) { int len = writev(STDOUT_FILENO, iov, out); if (len <= 0) err(1, "Write to stdout gave %i", len); iov_consume(iov, out, len); } + + /* + * We're finished with that buffer: if we're going to sleep, + * wait_for_vq_desc() will prod the Guest with an interrupt. + */ add_used(vq, head, 0); } @@ -862,15 +884,30 @@ static void net_output(struct virtqueue *vq) unsigned int head, out, in; struct iovec iov[vq->vring.num]; + /* We usually wait in here for the Guest to give us a packet. */ head = wait_for_vq_desc(vq, iov, &out, &in); if (in) errx(1, "Input buffers in net output queue?"); + /* + * Send the whole thing through to /dev/net/tun. It expects the exact + * same format: what a coincidence! + */ if (writev(net_info->tunfd, iov, out) < 0) errx(1, "Write to tun failed?"); + + /* + * Done with that one; wait_for_vq_desc() will send the interrupt if + * all packets are processed. + */ add_used(vq, head, 0); } -/* Will reading from this file descriptor block? */ +/* + * Handling network input is a bit trickier, because I've tried to optimize it. + * + * First we have a helper routine which tells is if from this file descriptor + * (ie. the /dev/net/tun device) will block: + */ static bool will_block(int fd) { fd_set fdset; @@ -880,7 +917,11 @@ static bool will_block(int fd) return select(fd+1, &fdset, NULL, NULL, &zero) != 1; } -/* This handles packets coming in from the tun device to our Guest. */ +/* + * This handles packets coming in from the tun device to our Guest. Like all + * service routines, it gets called again as soon as it returns, so you don't + * see a while(1) loop here. + */ static void net_input(struct virtqueue *vq) { int len; @@ -888,21 +929,38 @@ static void net_input(struct virtqueue *vq) struct iovec iov[vq->vring.num]; struct net_info *net_info = vq->dev->priv; + /* + * Get a descriptor to write an incoming packet into. This will also + * send an interrupt if they're out of descriptors. + */ head = wait_for_vq_desc(vq, iov, &out, &in); if (out) errx(1, "Output buffers in net input queue?"); - /* Deliver interrupt now, since we're about to sleep. */ + /* + * If it looks like we'll block reading from the tun device, send them + * an interrupt. + */ if (vq->pending_used && will_block(net_info->tunfd)) trigger_irq(vq); + /* + * Read in the packet. This is where we normally wait (when there's no + * incoming network traffic). + */ len = readv(net_info->tunfd, iov, in); if (len <= 0) err(1, "Failed to read from tun."); + + /* + * Mark that packet buffer as used, but don't interrupt here. We want + * to wait until we've done as much work as we can. + */ add_used(vq, head, len); } +/*:*/ -/* This is the helper to create threads. */ +/* This is the helper to create threads: run the service routine in a loop. */ static int do_thread(void *_vq) { struct virtqueue *vq = _vq; @@ -950,11 +1008,14 @@ static void reset_device(struct device *dev) signal(SIGCHLD, (void *)kill_launcher); } +/*L:216 + * This actually creates the thread which services the virtqueue for a device. + */ static void create_thread(struct virtqueue *vq) { /* - * Create stack for thread and run it. Since the stack grows upwards, - * we point the stack pointer to the end of this region. + * Create stack for thread. Since the stack grows upwards, we point + * the stack pointer to the end of this region. */ char *stack = malloc(32768); unsigned long args[] = { LHREQ_EVENTFD, @@ -966,17 +1027,22 @@ static void create_thread(struct virtqueue *vq) err(1, "Creating eventfd"); args[2] = vq->eventfd; - /* Attach an eventfd to this virtqueue: it will go off - * when the Guest does an LHCALL_NOTIFY for this vq. */ + /* + * Attach an eventfd to this virtqueue: it will go off when the Guest + * does an LHCALL_NOTIFY for this vq. + */ if (write(lguest_fd, &args, sizeof(args)) != 0) err(1, "Attaching eventfd"); - /* CLONE_VM: because it has to access the Guest memory, and - * SIGCHLD so we get a signal if it dies. */ + /* + * CLONE_VM: because it has to access the Guest memory, and SIGCHLD so + * we get a signal if it dies. + */ vq->thread = clone(do_thread, stack + 32768, CLONE_VM | SIGCHLD, vq); if (vq->thread == (pid_t)-1) err(1, "Creating clone"); - /* We close our local copy, now the child has it. */ + + /* We close our local copy now the child has it. */ close(vq->eventfd); } @@ -1028,7 +1094,10 @@ static void update_device_status(struct device *dev) } } -/* This is the generic routine we call when the Guest uses LHCALL_NOTIFY. */ +/*L:215 + * This is the generic routine we call when the Guest uses LHCALL_NOTIFY. In + * particular, it's used to notify us of device status changes during boot. + */ static void handle_output(unsigned long addr) { struct device *i; @@ -1037,18 +1106,32 @@ static void handle_output(unsigned long addr) for (i = devices.dev; i; i = i->next) { struct virtqueue *vq; - /* Notifications to device descriptors update device status. */ + /* + * Notifications to device descriptors mean they updated the + * device status. + */ if (from_guest_phys(addr) == i->desc) { update_device_status(i); return; } - /* Devices *can* be used before status is set to DRIVER_OK. */ + /* + * Devices *can* be used before status is set to DRIVER_OK. + * The original plan was that they would never do this: they + * would always finish setting up their status bits before + * actually touching the virtqueues. In practice, we allowed + * them to, and they do (eg. the disk probes for partition + * tables as part of initialization). + * + * If we see this, we start the device: once it's running, we + * expect the device to catch all the notifications. + */ for (vq = i->vq; vq; vq = vq->next) { if (addr != vq->config.pfn*getpagesize()) continue; if (i->running) errx(1, "Notification on running %s", i->name); + /* This just calls create_thread() for each virtqueue */ start_device(i); return; } @@ -1132,6 +1215,11 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs, vq->next = NULL; vq->last_avail_idx = 0; vq->dev = dev; + + /* + * This is the routine the service thread will run, and its Process ID + * once it's running. + */ vq->service = service; vq->thread = (pid_t)-1; @@ -1202,7 +1290,8 @@ static void set_config(struct device *dev, unsigned len, const void *conf) /* * This routine does all the creation and setup of a new device, including - * calling new_dev_desc() to allocate the descriptor and device memory. + * calling new_dev_desc() to allocate the descriptor and device memory. We + * don't actually start the service threads until later. * * See what I mean about userspace being boring? */ @@ -1478,19 +1567,7 @@ static void setup_tun_net(char *arg) verbose("device %u: tun %s: %s\n", devices.device_num, tapif, arg); } - -/* - * Our block (disk) device should be really simple: the Guest asks for a block - * number and we read or write that position in the file. Unfortunately, that - * was amazingly slow: the Guest waits until the read is finished before - * running anything else, even if it could have been doing useful work. - * - * We could use async I/O, except it's reputed to suck so hard that characters - * actually go missing from your code when you try to use it. - * - * So this was one reason why lguest now does all virtqueue servicing in - * separate threads: it's more efficient and more like a real device. - */ +/*:*/ /* This hangs off device->priv. */ struct vblk_info @@ -1512,8 +1589,16 @@ struct vblk_info /*L:210 * The Disk * - * Remember that the block device is handled by a separate I/O thread. We head - * straight into the core of that thread here: + * The disk only has one virtqueue, so it only has one thread. It is really + * simple: the Guest asks for a block number and we read or write that position + * in the file. + * + * Before we serviced each virtqueue in a separate thread, that was unacceptably + * slow: the Guest waits until the read is finished before running anything + * else, even if it could have been doing useful work. + * + * We could have used async I/O, except it's reputed to suck so hard that + * characters actually go missing from your code when you try to use it. */ static void blk_request(struct virtqueue *vq) { @@ -1525,7 +1610,10 @@ static void blk_request(struct virtqueue *vq) struct iovec iov[vq->vring.num]; off64_t off; - /* Get the next request. */ + /* + * Get the next request, where we normally wait. It triggers the + * interrupt to acknowledge previously serviced requests (if any). + */ head = wait_for_vq_desc(vq, iov, &out_num, &in_num); /* @@ -1539,6 +1627,10 @@ static void blk_request(struct virtqueue *vq) out = convert(&iov[0], struct virtio_blk_outhdr); in = convert(&iov[out_num+in_num-1], u8); + /* + * For historical reasons, block operations are expressed in 512 byte + * "sectors". + */ off = out->sector * 512; /* @@ -1614,6 +1706,7 @@ static void blk_request(struct virtqueue *vq) if (out->type & VIRTIO_BLK_T_BARRIER) fdatasync(vblk->fd); + /* Finished that request. */ add_used(vq, head, wlen); } @@ -1682,9 +1775,8 @@ static void rng_input(struct virtqueue *vq) errx(1, "Output buffers in rng?"); /* - * This is why we convert to iovecs: the readv() call uses them, and so - * it reads straight into the Guest's buffer. We loop to make sure we - * fill it. + * Just like the console write, we loop to cover the whole iovec. + * In this case, short reads actually happen quite a bit. */ while (!iov_empty(iov, in_num)) { len = readv(rng_info->rfd, iov, in_num); @@ -1818,7 +1910,9 @@ int main(int argc, char *argv[]) devices.lastdev = NULL; devices.next_irq = 1; + /* We're CPU 0. In fact, that's the only CPU possible right now. */ cpu_id = 0; + /* * We need to know how much memory so we can set up the device * descriptor and memory pages for the devices as we parse the command @@ -1926,7 +2020,7 @@ int main(int argc, char *argv[]) */ tell_kernel(start); - /* Ensure that we terminate if a child dies. */ + /* Ensure that we terminate if a device-servicing child dies. */ signal(SIGCHLD, kill_launcher); /* If we exit via err(), this kills all the threads, restores tty. */ diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h index cceb73e12e50..ba0eed8aa1a6 100644 --- a/arch/x86/include/asm/lguest_hcall.h +++ b/arch/x86/include/asm/lguest_hcall.h @@ -35,10 +35,10 @@ * operations? There are two ways: the direct way is to make a "hypercall", * to make requests of the Host Itself. * - * We use the KVM hypercall mechanism. Seventeen hypercalls are - * available: the hypercall number is put in the %eax register, and the - * arguments (when required) are placed in %ebx, %ecx, %edx and %esi. - * If a return value makes sense, it's returned in %eax. + * We use the KVM hypercall mechanism, though completely different hypercall + * numbers. Seventeen hypercalls are available: the hypercall number is put in + * the %eax register, and the arguments (when required) are placed in %ebx, + * %ecx, %edx and %esi. If a return value makes sense, it's returned in %eax. * * Grossly invalid calls result in Sudden Death at the hands of the vengeful * Host, rather than returning failure. This reflects Winston Churchill's diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c index 025c04d18f2b..d677fa9ca650 100644 --- a/arch/x86/lguest/boot.c +++ b/arch/x86/lguest/boot.c @@ -154,6 +154,7 @@ static void lazy_hcall1(unsigned long call, async_hcall(call, arg1, 0, 0, 0); } +/* You can imagine what lazy_hcall2, 3 and 4 look like. :*/ static void lazy_hcall2(unsigned long call, unsigned long arg1, unsigned long arg2) @@ -189,8 +190,10 @@ static void lazy_hcall4(unsigned long call, } #endif -/* When lazy mode is turned off reset the per-cpu lazy mode variable and then - * issue the do-nothing hypercall to flush any stored calls. */ +/*G:036 + * When lazy mode is turned off reset the per-cpu lazy mode variable and then + * issue the do-nothing hypercall to flush any stored calls. +:*/ static void lguest_leave_lazy_mmu_mode(void) { kvm_hypercall0(LHCALL_FLUSH_ASYNC); @@ -250,13 +253,11 @@ extern void lg_irq_enable(void); extern void lg_restore_fl(unsigned long flags); /*M:003 - * Note that we don't check for outstanding interrupts when we re-enable them - * (or when we unmask an interrupt). This seems to work for the moment, since - * interrupts are rare and we'll just get the interrupt on the next timer tick, - * but now we can run with CONFIG_NO_HZ, we should revisit this. One way would - * be to put the "irq_enabled" field in a page by itself, and have the Host - * write-protect it when an interrupt comes in when irqs are disabled. There - * will then be a page fault as soon as interrupts are re-enabled. + * We could be more efficient in our checking of outstanding interrupts, rather + * than using a branch. One way would be to put the "irq_enabled" field in a + * page by itself, and have the Host write-protect it when an interrupt comes + * in when irqs are disabled. There will then be a page fault as soon as + * interrupts are re-enabled. * * A better method is to implement soft interrupt disable generally for x86: * instead of disabling interrupts, we set a flag. If an interrupt does come @@ -568,7 +569,7 @@ static void lguest_write_cr4(unsigned long val) * cr3 ---> +---------+ * | --------->+---------+ * | | | PADDR1 | - * Top-level | | PADDR2 | + * Mid-level | | PADDR2 | * (PMD) page | | | * | | Lower-level | * | | (PTE) page | @@ -588,23 +589,62 @@ static void lguest_write_cr4(unsigned long val) * Index into top Index into second Offset within page * page directory page pagetable page * - * The kernel spends a lot of time changing both the top-level page directory - * and lower-level pagetable pages. The Guest doesn't know physical addresses, - * so while it maintains these page tables exactly like normal, it also needs - * to keep the Host informed whenever it makes a change: the Host will create - * the real page tables based on the Guests'. + * Now, unfortunately, this isn't the whole story: Intel added Physical Address + * Extension (PAE) to allow 32 bit systems to use 64GB of memory (ie. 36 bits). + * These are held in 64-bit page table entries, so we can now only fit 512 + * entries in a page, and the neat three-level tree breaks down. + * + * The result is a four level page table: + * + * cr3 --> [ 4 Upper ] + * [ Level ] + * [ Entries ] + * [(PUD Page)]---> +---------+ + * | --------->+---------+ + * | | | PADDR1 | + * Mid-level | | PADDR2 | + * (PMD) page | | | + * | | Lower-level | + * | | (PTE) page | + * | | | | + * .... .... + * + * + * And the virtual address is decoded as: + * + * 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + * |<-2->|<--- 9 bits ---->|<---- 9 bits --->|<------ 12 bits ------>| + * Index into Index into mid Index into lower Offset within page + * top entries directory page pagetable page + * + * It's too hard to switch between these two formats at runtime, so Linux only + * supports one or the other depending on whether CONFIG_X86_PAE is set. Many + * distributions turn it on, and not just for people with silly amounts of + * memory: the larger PTE entries allow room for the NX bit, which lets the + * kernel disable execution of pages and increase security. + * + * This was a problem for lguest, which couldn't run on these distributions; + * then Matias Zabaljauregui figured it all out and implemented it, and only a + * handful of puppies were crushed in the process! + * + * Back to our point: the kernel spends a lot of time changing both the + * top-level page directory and lower-level pagetable pages. The Guest doesn't + * know physical addresses, so while it maintains these page tables exactly + * like normal, it also needs to keep the Host informed whenever it makes a + * change: the Host will create the real page tables based on the Guests'. */ /* - * The Guest calls this to set a second-level entry (pte), ie. to map a page - * into a process' address space. We set the entry then tell the Host the - * toplevel and address this corresponds to. The Guest uses one pagetable per - * process, so we need to tell the Host which one we're changing (mm->pgd). + * The Guest calls this after it has set a second-level entry (pte), ie. to map + * a page into a process' address space. Wetell the Host the toplevel and + * address this corresponds to. The Guest uses one pagetable per process, so + * we need to tell the Host which one we're changing (mm->pgd). */ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { #ifdef CONFIG_X86_PAE + /* PAE needs to hand a 64 bit page table entry, so it uses two args. */ lazy_hcall4(LHCALL_SET_PTE, __pa(mm->pgd), addr, ptep->pte_low, ptep->pte_high); #else @@ -612,6 +652,7 @@ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr, #endif } +/* This is the "set and update" combo-meal-deal version. */ static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr, pte_t *ptep, pte_t pteval) { @@ -672,6 +713,11 @@ static void lguest_set_pte(pte_t *ptep, pte_t pteval) } #ifdef CONFIG_X86_PAE +/* + * With 64-bit PTE values, we need to be careful setting them: if we set 32 + * bits at a time, the hardware could see a weird half-set entry. These + * versions ensure we update all 64 bits at once. + */ static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte) { native_set_pte_atomic(ptep, pte); @@ -679,13 +725,14 @@ static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte) lazy_hcall1(LHCALL_FLUSH_TLB, 1); } -void lguest_pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep) +static void lguest_pte_clear(struct mm_struct *mm, unsigned long addr, + pte_t *ptep) { native_pte_clear(mm, addr, ptep); lguest_pte_update(mm, addr, ptep); } -void lguest_pmd_clear(pmd_t *pmdp) +static void lguest_pmd_clear(pmd_t *pmdp) { lguest_set_pmd(pmdp, __pmd(0)); } @@ -784,6 +831,14 @@ static void __init lguest_init_IRQ(void) irq_ctx_init(smp_processor_id()); } +/* + * With CONFIG_SPARSE_IRQ, interrupt descriptors are allocated as-needed, so + * rather than set them in lguest_init_IRQ we are called here every time an + * lguest device needs an interrupt. + * + * FIXME: irq_to_desc_alloc_node() can fail due to lack of memory, we should + * pass that up! + */ void lguest_setup_irq(unsigned int irq) { irq_to_desc_alloc_node(irq, 0); @@ -1298,7 +1353,7 @@ __init void lguest_init(void) */ switch_to_new_gdt(0); - /* As described in head_32.S, we map the first 128M of memory. */ + /* We actually boot with all memory mapped, but let's say 128MB. */ max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT; /* diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S index db6aa95eb054..27eac0faee48 100644 --- a/arch/x86/lguest/i386_head.S +++ b/arch/x86/lguest/i386_head.S @@ -102,6 +102,7 @@ send_interrupts: * create one manually here. */ .byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */ + /* Put eax back the way we found it. */ popl %eax ret @@ -125,6 +126,7 @@ ENTRY(lg_restore_fl) jnz send_interrupts /* Again, the normal path has used no extra registers. Clever, huh? */ ret +/*:*/ /* These demark the EIP range where host should never deliver interrupts. */ .global lguest_noirq_start diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c index cd058bc903ff..1e2cb846b3c9 100644 --- a/drivers/lguest/core.c +++ b/drivers/lguest/core.c @@ -217,10 +217,15 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user) /* * It's possible the Guest did a NOTIFY hypercall to the - * Launcher, in which case we return from the read() now. + * Launcher. */ if (cpu->pending_notify) { + /* + * Does it just needs to write to a registered + * eventfd (ie. the appropriate virtqueue thread)? + */ if (!send_notify_to_eventfd(cpu)) { + /* OK, we tell the main Laucher. */ if (put_user(cpu->pending_notify, user)) return -EFAULT; return sizeof(cpu->pending_notify); diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c index 787ab4bc09f0..83511eb0923d 100644 --- a/drivers/lguest/hypercalls.c +++ b/drivers/lguest/hypercalls.c @@ -59,7 +59,7 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args) case LHCALL_SHUTDOWN: { char msg[128]; /* - * Shutdown is such a trivial hypercall that we do it in four + * Shutdown is such a trivial hypercall that we do it in five * lines right here. * * If the lgread fails, it will call kill_guest() itself; the @@ -245,6 +245,10 @@ static void initialize(struct lg_cpu *cpu) * device), the Guest will still see the old page. In practice, this never * happens: why would the Guest read a page which it has never written to? But * a similar scenario might one day bite us, so it's worth mentioning. + * + * Note that if we used a shared anonymous mapping in the Launcher instead of + * mapping /dev/zero private, we wouldn't worry about cop-on-write. And we + * need that to switch the Launcher to processes (away from threads) anyway. :*/ /*H:100 diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index cc000e79c3d1..1401c1ace1ec 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -236,7 +236,7 @@ static void lg_notify(struct virtqueue *vq) extern void lguest_setup_irq(unsigned int irq); /* - * This routine finds the first virtqueue described in the configuration of + * This routine finds the Nth virtqueue described in the configuration of * this device and sets it up. * * This is kind of an ugly duckling. It'd be nicer to have a standard @@ -244,9 +244,6 @@ extern void lguest_setup_irq(unsigned int irq); * everyone wants to do it differently. The KVM coders want the Guest to * allocate its own pages and tell the Host where they are, but for lguest it's * simpler for the Host to simply tell us where the pages are. - * - * So we provide drivers with a "find the Nth virtqueue and set it up" - * function. */ static struct virtqueue *lg_find_vq(struct virtio_device *vdev, unsigned index, @@ -422,7 +419,11 @@ static void add_lguest_device(struct lguest_device_desc *d, /* This devices' parent is the lguest/ dir. */ ldev->vdev.dev.parent = lguest_root; - /* We have a unique device index thanks to the dev_index counter. */ + /* + * The device type comes straight from the descriptor. There's also a + * device vendor field in the virtio_device struct, which we leave as + * 0. + */ ldev->vdev.id.device = d->type; /* * We have a simple set of routines for querying the device's diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c index 7e92017103dc..b4d3f7ca554f 100644 --- a/drivers/lguest/lguest_user.c +++ b/drivers/lguest/lguest_user.c @@ -1,9 +1,8 @@ -/*P:200 - * This contains all the /dev/lguest code, whereby the userspace launcher +/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher * controls and communicates with the Guest. For example, the first write will - * tell us the Guest's memory layout, pagetable, entry point and kernel address - * offset. A read will run the Guest until something happens, such as a signal - * or the Guest doing a NOTIFY out to the Launcher. + * tell us the Guest's memory layout and entry point. A read will run the + * Guest until something happens, such as a signal or the Guest doing a NOTIFY + * out to the Launcher. :*/ #include #include @@ -13,14 +12,41 @@ #include #include "lg.h" +/*L:056 + * Before we move on, let's jump ahead and look at what the kernel does when + * it needs to look up the eventfds. That will complete our picture of how we + * use RCU. + * + * The notification value is in cpu->pending_notify: we return true if it went + * to an eventfd. + */ bool send_notify_to_eventfd(struct lg_cpu *cpu) { unsigned int i; struct lg_eventfd_map *map; - /* lg->eventfds is RCU-protected */ + /* + * This "rcu_read_lock()" helps track when someone is still looking at + * the (RCU-using) eventfds array. It's not actually a lock at all; + * indeed it's a noop in many configurations. (You didn't expect me to + * explain all the RCU secrets here, did you?) + */ rcu_read_lock(); + /* + * rcu_dereference is the counter-side of rcu_assign_pointer(); it + * makes sure we don't access the memory pointed to by + * cpu->lg->eventfds before cpu->lg->eventfds is set. Sounds crazy, + * but Alpha allows this! Paul McKenney points out that a really + * aggressive compiler could have the same effect: + * http://lists.ozlabs.org/pipermail/lguest/2009-July/001560.html + * + * So play safe, use rcu_dereference to get the rcu-protected pointer: + */ map = rcu_dereference(cpu->lg->eventfds); + /* + * Simple array search: even if they add an eventfd while we do this, + * we'll continue to use the old array and just won't see the new one. + */ for (i = 0; i < map->num; i++) { if (map->map[i].addr == cpu->pending_notify) { eventfd_signal(map->map[i].event, 1); @@ -28,14 +54,43 @@ bool send_notify_to_eventfd(struct lg_cpu *cpu) break; } } + /* We're done with the rcu-protected variable cpu->lg->eventfds. */ rcu_read_unlock(); + + /* If we cleared the notification, it's because we found a match. */ return cpu->pending_notify == 0; } +/*L:055 + * One of the more tricksy tricks in the Linux Kernel is a technique called + * Read Copy Update. Since one point of lguest is to teach lguest journeyers + * about kernel coding, I use it here. (In case you're curious, other purposes + * include learning about virtualization and instilling a deep appreciation for + * simplicity and puppies). + * + * We keep a simple array which maps LHCALL_NOTIFY values to eventfds, but we + * add new eventfds without ever blocking readers from accessing the array. + * The current Launcher only does this during boot, so that never happens. But + * Read Copy Update is cool, and adding a lock risks damaging even more puppies + * than this code does. + * + * We allocate a brand new one-larger array, copy the old one and add our new + * element. Then we make the lg eventfd pointer point to the new array. + * That's the easy part: now we need to free the old one, but we need to make + * sure no slow CPU somewhere is still looking at it. That's what + * synchronize_rcu does for us: waits until every CPU has indicated that it has + * moved on to know it's no longer using the old one. + * + * If that's unclear, see http://en.wikipedia.org/wiki/Read-copy-update. + */ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) { struct lg_eventfd_map *new, *old = lg->eventfds; + /* + * We don't allow notifications on value 0 anyway (pending_notify of + * 0 means "nothing pending"). + */ if (!addr) return -EINVAL; @@ -62,12 +117,20 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) } new->num++; - /* Now put new one in place. */ + /* + * Now put new one in place: rcu_assign_pointer() is a fancy way of + * doing "lg->eventfds = new", but it uses memory barriers to make + * absolutely sure that the contents of "new" written above is nailed + * down before we actually do the assignment. + * + * We have to think about these kinds of things when we're operating on + * live data without locks. + */ rcu_assign_pointer(lg->eventfds, new); /* * We're not in a big hurry. Wait until noone's looking at old - * version, then delete it. + * version, then free it. */ synchronize_rcu(); kfree(old); @@ -75,6 +138,14 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd) return 0; } +/*L:052 + * Receiving notifications from the Guest is usually done by attaching a + * particular LHCALL_NOTIFY value to an event filedescriptor. The eventfd will + * become readable when the Guest does an LHCALL_NOTIFY with that value. + * + * This is really convenient for processing each virtqueue in a separate + * thread. + */ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) { unsigned long addr, fd; @@ -86,6 +157,11 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input) if (get_user(fd, input) != 0) return -EFAULT; + /* + * Just make sure two callers don't add eventfds at once. We really + * only need to lock against callers adding to the same Guest, so using + * the Big Lguest Lock is overkill. But this is setup, not a fast path. + */ mutex_lock(&lguest_lock); err = add_eventfd(lg, addr, fd); mutex_unlock(&lguest_lock); @@ -106,6 +182,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input) if (irq >= LGUEST_IRQS) return -EINVAL; + /* + * Next time the Guest runs, the core code will see if it can deliver + * this interrupt. + */ set_interrupt(cpu, irq); return 0; } @@ -307,10 +387,10 @@ unlock: * The first operation the Launcher does must be a write. All writes * start with an unsigned long number: for the first write this must be * LHREQ_INITIALIZE to set up the Guest. After that the Launcher can use - * writes of other values to send interrupts. + * writes of other values to send interrupts or set up receipt of notifications. * * Note that we overload the "offset" in the /dev/lguest file to indicate what - * CPU number we're dealing with. Currently this is always 0, since we only + * CPU number we're dealing with. Currently this is always 0 since we only * support uniprocessor Guests, but you can see the beginnings of SMP support * here. */ diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c index 3da902e4b4cb..a8d0aee3bc0e 100644 --- a/drivers/lguest/page_tables.c +++ b/drivers/lguest/page_tables.c @@ -29,10 +29,10 @@ /*H:300 * The Page Table Code * - * We use two-level page tables for the Guest. If you're not entirely - * comfortable with virtual addresses, physical addresses and page tables then - * I recommend you review arch/x86/lguest/boot.c's "Page Table Handling" (with - * diagrams!). + * We use two-level page tables for the Guest, or three-level with PAE. If + * you're not entirely comfortable with virtual addresses, physical addresses + * and page tables then I recommend you review arch/x86/lguest/boot.c's "Page + * Table Handling" (with diagrams!). * * The Guest keeps page tables, but we maintain the actual ones here: these are * called "shadow" page tables. Which is a very Guest-centric name: these are @@ -52,9 +52,8 @@ :*/ /* - * 1024 entries in a page table page maps 1024 pages: 4MB. The Switcher is - * conveniently placed at the top 4MB, so it uses a separate, complete PTE - * page. + * The Switcher uses the complete top PTE page. That's 1024 PTE entries (4MB) + * or 512 PTE entries with PAE (2MB). */ #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1) @@ -81,7 +80,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages); /*H:320 * The page table code is curly enough to need helper functions to keep it - * clear and clean. + * clear and clean. The kernel itself provides many of them; one advantage + * of insisting that the Guest and Host use the same CONFIG_PAE setting. * * There are two functions which return pointers to the shadow (aka "real") * page tables. @@ -155,7 +155,7 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr) } /* - * These two functions just like the above two, except they access the Guest + * These functions are just like the above two, except they access the Guest * page tables. Hence they return a Guest address. */ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) @@ -165,6 +165,7 @@ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr) } #ifdef CONFIG_X86_PAE +/* Follow the PGD to the PMD. */ static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr) { unsigned long gpage = pgd_pfn(gpgd) << PAGE_SHIFT; @@ -172,6 +173,7 @@ static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr) return gpage + pmd_index(vaddr) * sizeof(pmd_t); } +/* Follow the PMD to the PTE. */ static unsigned long gpte_addr(struct lg_cpu *cpu, pmd_t gpmd, unsigned long vaddr) { @@ -181,6 +183,7 @@ static unsigned long gpte_addr(struct lg_cpu *cpu, return gpage + pte_index(vaddr) * sizeof(pte_t); } #else +/* Follow the PGD to the PTE (no mid-level for !PAE). */ static unsigned long gpte_addr(struct lg_cpu *cpu, pgd_t gpgd, unsigned long vaddr) { @@ -314,6 +317,7 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) pte_t gpte; pte_t *spte; + /* Mid level for PAE. */ #ifdef CONFIG_X86_PAE pmd_t *spmd; pmd_t gpmd; @@ -391,6 +395,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode) */ gpte_ptr = gpte_addr(cpu, gpgd, vaddr); #endif + + /* Read the actual PTE value. */ gpte = lgread(cpu, gpte_ptr, pte_t); /* If this page isn't in the Guest page tables, we can't page it in. */ @@ -507,6 +513,7 @@ void pin_page(struct lg_cpu *cpu, unsigned long vaddr) if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2)) kill_guest(cpu, "bad stack page %#lx", vaddr); } +/*:*/ #ifdef CONFIG_X86_PAE static void release_pmd(pmd_t *spmd) @@ -543,7 +550,11 @@ static void release_pgd(pgd_t *spgd) } #else /* !CONFIG_X86_PAE */ -/*H:450 If we chase down the release_pgd() code, it looks like this: */ +/*H:450 + * If we chase down the release_pgd() code, the non-PAE version looks like + * this. The PAE version is almost identical, but instead of calling + * release_pte it calls release_pmd(), which looks much like this. + */ static void release_pgd(pgd_t *spgd) { /* If the entry's not present, there's nothing to release. */ @@ -898,17 +909,21 @@ void guest_set_pgd(struct lguest *lg, unsigned long gpgdir, u32 idx) /* ... throw it away. */ release_pgd(lg->pgdirs[pgdir].pgdir + idx); } + #ifdef CONFIG_X86_PAE +/* For setting a mid-level, we just throw everything away. It's easy. */ void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx) { guest_pagetable_clear_all(&lg->cpus[0]); } #endif -/* - * Once we know how much memory we have we can construct simple identity (which +/*H:505 + * To get through boot, we construct simple identity page mappings (which * set virtual == physical) and linear mappings which will get the Guest far - * enough into the boot to create its own. + * enough into the boot to create its own. The linear mapping means we + * simplify the Guest boot, but it makes assumptions about their PAGE_OFFSET, + * as you'll see. * * We lay them out of the way, just below the initrd (which is why we need to * know its size here). @@ -944,6 +959,10 @@ static unsigned long setup_pagetables(struct lguest *lg, linear = (void *)pgdir - linear_pages * PAGE_SIZE; #ifdef CONFIG_X86_PAE + /* + * And the single mid page goes below that. We only use one, but + * that's enough to map 1G, which definitely gets us through boot. + */ pmds = (void *)linear - PAGE_SIZE; #endif /* @@ -957,13 +976,14 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } +#ifdef CONFIG_X86_PAE /* - * The top level points to the linear page table pages above. - * We setup the identity and linear mappings here. + * Make the Guest PMD entries point to the corresponding place in the + * linear mapping (up to one page worth of PMD). */ -#ifdef CONFIG_X86_PAE for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD; i += PTRS_PER_PTE, j++) { + /* FIXME: native_set_pmd is overkill here. */ native_set_pmd(&pmd, __pmd(((unsigned long)(linear + i) - mem_base) | _PAGE_PRESENT | _PAGE_RW | _PAGE_USER)); @@ -971,18 +991,36 @@ static unsigned long setup_pagetables(struct lguest *lg, return -EFAULT; } + /* One PGD entry, pointing to that PMD page. */ set_pgd(&pgd, __pgd(((u32)pmds - mem_base) | _PAGE_PRESENT)); + /* Copy it in as the first PGD entry (ie. addresses 0-1G). */ if (copy_to_user(&pgdir[0], &pgd, sizeof(pgd)) != 0) return -EFAULT; + /* + * And the third PGD entry (ie. addresses 3G-4G). + * + * FIXME: This assumes that PAGE_OFFSET for the Guest is 0xC0000000. + */ if (copy_to_user(&pgdir[3], &pgd, sizeof(pgd)) != 0) return -EFAULT; #else + /* + * The top level points to the linear page table pages above. + * We setup the identity and linear mappings here. + */ phys_linear = (unsigned long)linear - mem_base; for (i = 0; i < mapped_pages; i += PTRS_PER_PTE) { pgd_t pgd; + /* + * Create a PGD entry which points to the right part of the + * linear PTE pages. + */ pgd = __pgd((phys_linear + i * sizeof(pte_t)) | (_PAGE_PRESENT | _PAGE_RW | _PAGE_USER)); + /* + * Copy it into the PGD page at 0 and PAGE_OFFSET. + */ if (copy_to_user(&pgdir[i / PTRS_PER_PTE], &pgd, sizeof(pgd)) || copy_to_user(&pgdir[pgd_index(PAGE_OFFSET) + i / PTRS_PER_PTE], @@ -992,8 +1030,8 @@ static unsigned long setup_pagetables(struct lguest *lg, #endif /* - * We return the top level (guest-physical) address: remember where - * this is. + * We return the top level (guest-physical) address: we remember where + * this is to write it into lguest_data when the Guest initializes. */ return (unsigned long)pgdir - mem_base; } @@ -1031,7 +1069,9 @@ int init_guest_pagetable(struct lguest *lg) lg->pgdirs[0].pgdir = (pgd_t *)get_zeroed_page(GFP_KERNEL); if (!lg->pgdirs[0].pgdir) return -ENOMEM; + #ifdef CONFIG_X86_PAE + /* For PAE, we also create the initial mid-level. */ pgd = lg->pgdirs[0].pgdir; pmd_table = (pmd_t *) get_zeroed_page(GFP_KERNEL); if (!pmd_table) @@ -1040,11 +1080,13 @@ int init_guest_pagetable(struct lguest *lg) set_pgd(pgd + SWITCHER_PGD_INDEX, __pgd(__pa(pmd_table) | _PAGE_PRESENT)); #endif + + /* This is the current page table. */ lg->cpus[0].cpu_pgd = 0; return 0; } -/* When the Guest calls LHCALL_LGUEST_INIT we do more setup. */ +/*H:508 When the Guest calls LHCALL_LGUEST_INIT we do more setup. */ void page_table_guest_data_init(struct lg_cpu *cpu) { /* We get the kernel address: above this is all kernel memory. */ @@ -1105,12 +1147,16 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages) pmd_t switcher_pmd; pmd_t *pmd_table; + /* FIXME: native_set_pmd is overkill here. */ native_set_pmd(&switcher_pmd, pfn_pmd(__pa(switcher_pte_page) >> PAGE_SHIFT, PAGE_KERNEL_EXEC)); + /* Figure out where the pmd page is, by reading the PGD, and converting + * it to a virtual address. */ pmd_table = __va(pgd_pfn(cpu->lg-> pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX]) << PAGE_SHIFT); + /* Now write it into the shadow page table. */ native_set_pmd(&pmd_table[SWITCHER_PMD_INDEX], switcher_pmd); #else pgd_t switcher_pgd; diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c index 96f7d88ec7f8..6ae388849a3b 100644 --- a/drivers/lguest/x86/core.c +++ b/drivers/lguest/x86/core.c @@ -187,7 +187,7 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages) * also simplify copy_in_guest_info(). Note that we'd still need to restore * things when we exit to Launcher userspace, but that's fairly easy. * - * We could also try using this hooks for PGE, but that might be too expensive. + * We could also try using these hooks for PGE, but that might be too expensive. * * The hooks were designed for KVM, but we can also put them to good use. :*/ diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S index 6dec09793836..40634b0db9f7 100644 --- a/drivers/lguest/x86/switcher_32.S +++ b/drivers/lguest/x86/switcher_32.S @@ -1,7 +1,7 @@ /*P:900 - * This is the Switcher: code which sits at 0xFFC00000 astride both the - * Host and Guest to do the low-level Guest<->Host switch. It is as simple as - * it can be made, but it's naturally very specific to x86. + * This is the Switcher: code which sits at 0xFFC00000 (or 0xFFE00000) astride + * both the Host and Guest to do the low-level Guest<->Host switch. It is as + * simple as it can be made, but it's naturally very specific to x86. * * You have now completed Preparation. If this has whet your appetite; if you * are feeling invigorated and refreshed then the next, more challenging stage -- cgit v1.2.3 From 1842f23c05b6a866be831aa60bc8a8731c58ddd0 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Thu, 30 Jul 2009 16:03:46 -0600 Subject: lguest and virtio: cleanup struct definitions to Linux style. I've been doing this for years, and akpm picked me up on it about 12 months ago. lguest partly serves as example code, so let's do it Right. Also, remove two unused fields in struct vblk_info in the example launcher. Signed-off-by: Rusty Russell Cc: Ingo Molnar --- Documentation/lguest/lguest.c | 21 +++++---------------- drivers/lguest/lg.h | 9 +++------ drivers/lguest/lguest_device.c | 3 +-- include/linux/lguest.h | 3 +-- include/linux/virtio_blk.h | 6 ++---- include/linux/virtio_config.h | 3 +-- include/linux/virtio_net.h | 6 ++---- include/linux/virtio_ring.h | 12 ++++-------- 8 files changed, 19 insertions(+), 44 deletions(-) (limited to 'drivers') diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c index 45163651b519..950cde6d6e58 100644 --- a/Documentation/lguest/lguest.c +++ b/Documentation/lguest/lguest.c @@ -93,8 +93,7 @@ static int lguest_fd; static unsigned int __thread cpu_id; /* This is our list of devices. */ -struct device_list -{ +struct device_list { /* Counter to assign interrupt numbers. */ unsigned int next_irq; @@ -114,8 +113,7 @@ struct device_list static struct device_list devices; /* The device structure describes a single device. */ -struct device -{ +struct device { /* The linked-list pointer. */ struct device *next; @@ -140,8 +138,7 @@ struct device }; /* The virtqueue structure describes a queue attached to a device. */ -struct virtqueue -{ +struct virtqueue { struct virtqueue *next; /* Which device owns me. */ @@ -779,8 +776,7 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len) * * We associate some data with the console for our exit hack. */ -struct console_abort -{ +struct console_abort { /* How many times have they hit ^C? */ int count; /* When did they start? */ @@ -1570,20 +1566,13 @@ static void setup_tun_net(char *arg) /*:*/ /* This hangs off device->priv. */ -struct vblk_info -{ +struct vblk_info { /* The size of the file. */ off64_t len; /* The file descriptor for the file. */ int fd; - /* IO thread listens on this file descriptor [0]. */ - int workpipe[2]; - - /* IO thread writes to this file descriptor to mark it done, then - * Launcher triggers interrupt to Guest. */ - int done_fd; }; /*L:210 diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h index 74c0db691b53..bc28745d05af 100644 --- a/drivers/lguest/lg.h +++ b/drivers/lguest/lg.h @@ -16,15 +16,13 @@ void free_pagetables(void); int init_pagetables(struct page **switcher_page, unsigned int pages); -struct pgdir -{ +struct pgdir { unsigned long gpgdir; pgd_t *pgdir; }; /* We have two pages shared with guests, per cpu. */ -struct lguest_pages -{ +struct lguest_pages { /* This is the stack page mapped rw in guest */ char spare[PAGE_SIZE - sizeof(struct lguest_regs)]; struct lguest_regs regs; @@ -89,8 +87,7 @@ struct lg_eventfd_map { }; /* The private info the thread maintains about the guest. */ -struct lguest -{ +struct lguest { struct lguest_data __user *lguest_data; struct lg_cpu cpus[NR_CPUS]; unsigned int nr_cpus; diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c index 1401c1ace1ec..b6200bc39b58 100644 --- a/drivers/lguest/lguest_device.c +++ b/drivers/lguest/lguest_device.c @@ -207,8 +207,7 @@ static void lg_reset(struct virtio_device *vdev) */ /*D:140 This is the information we remember about each virtqueue. */ -struct lguest_vq_info -{ +struct lguest_vq_info { /* A copy of the information contained in the device config. */ struct lguest_vqconfig config; diff --git a/include/linux/lguest.h b/include/linux/lguest.h index 0a3a11afd64b..2fb1dcbcb5aa 100644 --- a/include/linux/lguest.h +++ b/include/linux/lguest.h @@ -18,8 +18,7 @@ * lguest_data". Once the Guest's initialization hypercall tells the Host where * this is, the Guest and Host both publish information in it. :*/ -struct lguest_data -{ +struct lguest_data { /* * 512 == enabled (same as eflags in normal hardware). The Guest * changes interrupts so often that a hypercall is too slow. diff --git a/include/linux/virtio_blk.h b/include/linux/virtio_blk.h index be7d255fc7cf..8dab9f2b8832 100644 --- a/include/linux/virtio_blk.h +++ b/include/linux/virtio_blk.h @@ -20,8 +20,7 @@ #define VIRTIO_BLK_ID_BYTES (sizeof(__u16[256])) /* IDENTIFY DATA */ -struct virtio_blk_config -{ +struct virtio_blk_config { /* The capacity (in 512-byte sectors). */ __u64 capacity; /* The maximum segment size (if VIRTIO_BLK_F_SIZE_MAX) */ @@ -50,8 +49,7 @@ struct virtio_blk_config #define VIRTIO_BLK_T_BARRIER 0x80000000 /* This is the first element of the read scatter-gather list. */ -struct virtio_blk_outhdr -{ +struct virtio_blk_outhdr { /* VIRTIO_BLK_T* */ __u32 type; /* io priority. */ diff --git a/include/linux/virtio_config.h b/include/linux/virtio_config.h index 99f514575f6a..e547e3c8ee9a 100644 --- a/include/linux/virtio_config.h +++ b/include/linux/virtio_config.h @@ -79,8 +79,7 @@ * the dev->feature bits if it wants. */ typedef void vq_callback_t(struct virtqueue *); -struct virtio_config_ops -{ +struct virtio_config_ops { void (*get)(struct virtio_device *vdev, unsigned offset, void *buf, unsigned len); void (*set)(struct virtio_device *vdev, unsigned offset, diff --git a/include/linux/virtio_net.h b/include/linux/virtio_net.h index 9c543d6ac535..d8dd539c9f48 100644 --- a/include/linux/virtio_net.h +++ b/include/linux/virtio_net.h @@ -31,8 +31,7 @@ #define VIRTIO_NET_S_LINK_UP 1 /* Link is up */ -struct virtio_net_config -{ +struct virtio_net_config { /* The config defining mac address (if VIRTIO_NET_F_MAC) */ __u8 mac[6]; /* See VIRTIO_NET_F_STATUS and VIRTIO_NET_S_* above */ @@ -41,8 +40,7 @@ struct virtio_net_config /* This is the first element of the scatter-gather list. If you don't * specify GSO or CSUM features, you can simply ignore the header. */ -struct virtio_net_hdr -{ +struct virtio_net_hdr { #define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 // Use csum_start, csum_offset __u8 flags; #define VIRTIO_NET_HDR_GSO_NONE 0 // Not a GSO frame diff --git a/include/linux/virtio_ring.h b/include/linux/virtio_ring.h index 693e0ec5afa6..e4d144b132b5 100644 --- a/include/linux/virtio_ring.h +++ b/include/linux/virtio_ring.h @@ -30,8 +30,7 @@ #define VIRTIO_RING_F_INDIRECT_DESC 28 /* Virtio ring descriptors: 16 bytes. These can chain together via "next". */ -struct vring_desc -{ +struct vring_desc { /* Address (guest-physical). */ __u64 addr; /* Length. */ @@ -42,24 +41,21 @@ struct vring_desc __u16 next; }; -struct vring_avail -{ +struct vring_avail { __u16 flags; __u16 idx; __u16 ring[]; }; /* u32 is used here for ids for padding reasons. */ -struct vring_used_elem -{ +struct vring_used_elem { /* Index of start of used descriptor chain. */ __u32 id; /* Total length of the descriptor chain which was used (written to) */ __u32 len; }; -struct vring_used -{ +struct vring_used { __u16 flags; __u16 idx; struct vring_used_elem ring[]; -- cgit v1.2.3 From dfb3cf00e402686f671db697adbd8b9f4c219268 Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:02 +0200 Subject: [SCSI] zfcp: Fix invalid command order We should not modify the port status after triggering an ERP action for the port. It is not guaranteed which status is finally active when the ERP action is performed. This can lead to situations which are unwanted and hard to debug in case of a failure. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index c57658f3d34f..bbb7ef0b052d 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1731,15 +1731,16 @@ static void zfcp_fsf_close_physical_port_handler(struct zfcp_fsf_req *req) zfcp_fsf_access_denied_port(req, port); break; case FSF_PORT_BOXED: - zfcp_erp_port_boxed(port, "fscpph2", req); - req->status |= ZFCP_STATUS_FSFREQ_ERROR | - ZFCP_STATUS_FSFREQ_RETRY; /* can't use generic zfcp_erp_modify_port_status because * ZFCP_STATUS_COMMON_OPEN must not be reset for the port */ atomic_clear_mask(ZFCP_STATUS_PORT_PHYS_OPEN, &port->status); list_for_each_entry(unit, &port->unit_list_head, list) atomic_clear_mask(ZFCP_STATUS_COMMON_OPEN, &unit->status); + zfcp_erp_port_boxed(port, "fscpph2", req); + req->status |= ZFCP_STATUS_FSFREQ_ERROR | + ZFCP_STATUS_FSFREQ_RETRY; + break; case FSF_ADAPTER_STATUS_AVAILABLE: switch (header->fsf_status_qual.word[0]) { -- cgit v1.2.3 From acf7b86150701de105aa8307b4b3f9dc533c45bb Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:03 +0200 Subject: [SCSI] zfcp: Acquire qdio_stat_lock when reading the queue utilization req_q_util is not atomic, so the qdio_stat_lock must be held when reading this variable. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_sysfs.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_sysfs.c b/drivers/s390/scsi/zfcp_sysfs.c index 3e51e64d1108..0fe5cce818cb 100644 --- a/drivers/s390/scsi/zfcp_sysfs.c +++ b/drivers/s390/scsi/zfcp_sysfs.c @@ -494,9 +494,14 @@ static ssize_t zfcp_sysfs_adapter_q_full_show(struct device *dev, struct Scsi_Host *scsi_host = class_to_shost(dev); struct zfcp_adapter *adapter = (struct zfcp_adapter *) scsi_host->hostdata[0]; + u64 util; + + spin_lock_bh(&adapter->qdio_stat_lock); + util = adapter->req_q_util; + spin_unlock_bh(&adapter->qdio_stat_lock); return sprintf(buf, "%d %llu\n", atomic_read(&adapter->qdio_outb_full), - (unsigned long long)adapter->req_q_util); + (unsigned long long)util); } static DEVICE_ATTR(queue_full, S_IRUGO, zfcp_sysfs_adapter_q_full_show, NULL); -- cgit v1.2.3 From 1e9b16430ff4fd09408a74342d6b8338228e2f70 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:04 +0200 Subject: [SCSI] zfcp: Return -ENOMEM for allocation failures in zfcp_fsf When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of -EIO. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index bbb7ef0b052d..c4eb62b32a32 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -722,7 +722,7 @@ static struct zfcp_fsf_req *zfcp_fsf_req_create(struct zfcp_adapter *adapter, req = zfcp_fsf_alloc_qtcb(pool); if (unlikely(!req)) - return ERR_PTR(-EIO); + return ERR_PTR(-ENOMEM); if (adapter->req_no == 0) adapter->req_no++; -- cgit v1.2.3 From 688a1820bde27749f22b18b94ef1c9bc179b1b29 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:05 +0200 Subject: [SCSI] zfcp: Use correct flags for zfcp_erp_notify zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the nameserver did not return the d_id. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 8030e25152fb..e7d7ef55e37d 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -854,10 +854,10 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work) retval = zfcp_fc_ns_gid_pn(&port->erp_action); if (retval == -ENOMEM) - zfcp_erp_notify(&port->erp_action, ZFCP_ERP_NOMEM); + zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM); port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; if (retval) - zfcp_erp_notify(&port->erp_action, ZFCP_ERP_FAILED); + zfcp_erp_notify(&port->erp_action, 0); zfcp_port_put(port); } -- cgit v1.2.3 From 426f6059b0eb66cec139f4b9066168ab72b85774 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:06 +0200 Subject: [SCSI] zfcp: Use unchained mode for small ct and els requests The ELS ADISC and the GID_PN requests sent from zfcp fit into unchained FSF requests. Change the FSF allocation logic to use unchained requests whenever possible where everything fits in one SBAL. This avoids acquiring more SBALs than necessary, especially during zfcp recovery when things might be stalled. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 33 +++++++++++++++++++++++++-------- 1 file changed, 25 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index c4eb62b32a32..bec912547fb8 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1010,6 +1010,23 @@ skip_fsfstatus: send_ct->handler(send_ct->handler_data); } +static void zfcp_fsf_setup_ct_els_unchained(struct qdio_buffer_element *sbale, + struct scatterlist *sg_req, + struct scatterlist *sg_resp) +{ + sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ; + sbale[2].addr = sg_virt(sg_req); + sbale[2].length = sg_req->length; + sbale[3].addr = sg_virt(sg_resp); + sbale[3].length = sg_resp->length; + sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY; +} + +static int zfcp_fsf_one_sbal(struct scatterlist *sg) +{ + return sg_is_last(sg) && sg->length <= PAGE_SIZE; +} + static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, struct scatterlist *sg_req, struct scatterlist *sg_resp, @@ -1020,16 +1037,16 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, int bytes; if (!(feat & FSF_FEATURE_ELS_CT_CHAINED_SBALS)) { - if (sg_req->length > PAGE_SIZE || sg_resp->length > PAGE_SIZE || - !sg_is_last(sg_req) || !sg_is_last(sg_resp)) + if (!zfcp_fsf_one_sbal(sg_req) || !zfcp_fsf_one_sbal(sg_resp)) return -EOPNOTSUPP; - sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ; - sbale[2].addr = sg_virt(sg_req); - sbale[2].length = sg_req->length; - sbale[3].addr = sg_virt(sg_resp); - sbale[3].length = sg_resp->length; - sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY; + zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp); + return 0; + } + + /* use single, unchained SBAL if it can hold the request */ + if (zfcp_fsf_one_sbal(sg_req) && zfcp_fsf_one_sbal(sg_resp)) { + zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp); return 0; } -- cgit v1.2.3 From 9072df4dc6e8fd569d583815edb0198af4b688b8 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:07 +0200 Subject: [SCSI] zfcp: Use -EIO for SBAL allocation failures -ENOMEM is for memory allocation problems, -EIO for queue/SBAL allocation problems. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index bec912547fb8..0c24695a53cb 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1053,14 +1053,14 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req, bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ, sg_req, max_sbals); if (bytes <= 0) - return -ENOMEM; + return -EIO; req->qtcb->bottom.support.req_buf_length = bytes; req->sbale_curr = ZFCP_LAST_SBALE_PER_SBAL; bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ, sg_resp, max_sbals); if (bytes <= 0) - return -ENOMEM; + return -EIO; req->qtcb->bottom.support.resp_buf_length = bytes; return 0; @@ -2559,7 +2559,6 @@ struct zfcp_fsf_req *zfcp_fsf_control_file(struct zfcp_adapter *adapter, bytes = zfcp_qdio_sbals_from_sg(req, direction, fsf_cfdc->sg, FSF_MAX_SBALS_PER_REQ); if (bytes != ZFCP_CFDC_MAX_SIZE) { - retval = -ENOMEM; zfcp_fsf_req_free(req); goto out; } -- cgit v1.2.3 From ddb3e0c111fed0a8bf74884dc918274acec2b618 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:08 +0200 Subject: [SCSI] zfcp: Fix logic for physical port close After closing the port, we want it to be "not open" to consider the action to be successful. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index e7d7ef55e37d..0a7c6aef532a 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -801,7 +801,7 @@ static int zfcp_erp_port_forced_strategy(struct zfcp_erp_action *erp_action) return ZFCP_ERP_FAILED; case ZFCP_ERP_STEP_PHYS_PORT_CLOSING: - if (status & ZFCP_STATUS_PORT_PHYS_OPEN) + if (!(status & ZFCP_STATUS_PORT_PHYS_OPEN)) return ZFCP_ERP_SUCCEEDED; } return ZFCP_ERP_FAILED; -- cgit v1.2.3 From 85600f7f8370fe5b4be0debd8b401de7986b52ae Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:09 +0200 Subject: [SCSI] zfcp: Fix erp escalation procedure If an action fails, retry it until the erp count exceeds the threshold. If there is something fundamentally wrong, the FSF layer will trigger a more appropriate action depending on the FSF status codes. The followup for successful actions is a different followup than retrying failed actions, so split the code two functions to make this clear. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 50 +++++++++++++++++++++----------------------- 1 file changed, 24 insertions(+), 26 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 0a7c6aef532a..b5562f952654 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -553,40 +553,35 @@ static void _zfcp_erp_unit_reopen_all(struct zfcp_port *port, int clear, _zfcp_erp_unit_reopen(unit, clear, id, ref); } -static void zfcp_erp_strategy_followup_actions(struct zfcp_erp_action *act) +static void zfcp_erp_strategy_followup_failed(struct zfcp_erp_action *act) { - struct zfcp_adapter *adapter = act->adapter; - struct zfcp_port *port = act->port; - struct zfcp_unit *unit = act->unit; - u32 status = act->status; - - /* initiate follow-up actions depending on success of finished action */ switch (act->action) { - case ZFCP_ERP_ACTION_REOPEN_ADAPTER: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen_all(adapter, 0, "ersfa_1", NULL); - else - _zfcp_erp_adapter_reopen(adapter, 0, "ersfa_2", NULL); + _zfcp_erp_adapter_reopen(act->adapter, 0, "ersff_1", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen(port, 0, "ersfa_3", NULL); - else - _zfcp_erp_adapter_reopen(adapter, 0, "ersfa_4", NULL); + _zfcp_erp_port_forced_reopen(act->port, 0, "ersff_2", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_PORT: - if (status == ZFCP_ERP_SUCCEEDED) - _zfcp_erp_unit_reopen_all(port, 0, "ersfa_5", NULL); - else - _zfcp_erp_port_forced_reopen(port, 0, "ersfa_6", NULL); + _zfcp_erp_port_reopen(act->port, 0, "ersff_3", NULL); break; - case ZFCP_ERP_ACTION_REOPEN_UNIT: - if (status != ZFCP_ERP_SUCCEEDED) - _zfcp_erp_port_reopen(unit->port, 0, "ersfa_7", NULL); + _zfcp_erp_unit_reopen(act->unit, 0, "ersff_4", NULL); + break; + } +} + +static void zfcp_erp_strategy_followup_success(struct zfcp_erp_action *act) +{ + switch (act->action) { + case ZFCP_ERP_ACTION_REOPEN_ADAPTER: + _zfcp_erp_port_reopen_all(act->adapter, 0, "ersfs_1", NULL); + break; + case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED: + _zfcp_erp_port_reopen(act->port, 0, "ersfs_2", NULL); + break; + case ZFCP_ERP_ACTION_REOPEN_PORT: + _zfcp_erp_unit_reopen_all(act->port, 0, "ersfs_3", NULL); break; } } @@ -1289,7 +1284,10 @@ static int zfcp_erp_strategy(struct zfcp_erp_action *erp_action) retval = zfcp_erp_strategy_statechange(erp_action, retval); if (retval == ZFCP_ERP_EXIT) goto unlock; - zfcp_erp_strategy_followup_actions(erp_action); + if (retval == ZFCP_ERP_SUCCEEDED) + zfcp_erp_strategy_followup_success(erp_action); + if (retval == ZFCP_ERP_FAILED) + zfcp_erp_strategy_followup_failed(erp_action); unlock: write_unlock(&adapter->erp_lock); -- cgit v1.2.3 From cbf1ed0264da104573458aedc220ebfcd02567f6 Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:10 +0200 Subject: [SCSI] zfcp: Recover from stalled outbound queue Depending on interruptions on some storage systems, the complete channel can stall which looks like an outbound queue stall to Linux. When trying to acquire a free SBAL for a non-SCSI command, zfcp waits for 5 seconds for a free slot to appear. This is the right place to detect a queue stall: If the wait times out, we assume a stalled queue and try to recover this. The overall strategy should be to trigger the erp from specific events, and not try an overall escalation from one failed port to a full-blown queue recovery. If we manage to send a command, the status codes for this command or a timeout will trigger the right follow-on actions. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fsf.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index 0c24695a53cb..b7e48844056a 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -670,8 +670,11 @@ static int zfcp_fsf_req_sbal_get(struct zfcp_adapter *adapter) zfcp_fsf_sbal_check(adapter), 5 * HZ); if (ret > 0) return 0; - if (!ret) + if (!ret) { atomic_inc(&adapter->qdio_outb_full); + /* assume hanging outbound queue, try queue recovery */ + zfcp_erp_adapter_reopen(adapter, 0, "fsrsg_1", NULL); + } spin_lock_bh(&adapter->req_q_lock); return -EIO; -- cgit v1.2.3 From 379d6bf6573ee6541a38bbe9140c1f0b94e3feae Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:11 +0200 Subject: [SCSI] zfcp: Add port only once to FC transport class When calling fc_remote_port_add make sure to not call it again before fc_remote_port_delete has been called. In other words, ensure to create a new fc_rport, then delete it, then create a new one again. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_scsi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c index 967ede73f4c5..ba32709921a4 100644 --- a/drivers/s390/scsi/zfcp_scsi.c +++ b/drivers/s390/scsi/zfcp_scsi.c @@ -534,6 +534,9 @@ static void zfcp_scsi_rport_register(struct zfcp_port *port) struct fc_rport_identifiers ids; struct fc_rport *rport; + if (port->rport) + return; + ids.node_name = port->wwnn; ids.port_name = port->wwpn; ids.port_id = port->d_id; @@ -557,8 +560,10 @@ static void zfcp_scsi_rport_block(struct zfcp_port *port) { struct fc_rport *rport = port->rport; - if (rport) + if (rport) { fc_remote_port_delete(rport); + port->rport = NULL; + } } void zfcp_scsi_schedule_rport_register(struct zfcp_port *port) -- cgit v1.2.3 From 17a093ef018481ee1760da19568bad3c11da395d Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:12 +0200 Subject: [SCSI] zfcp: avoid double notify in lowmem scenario In a LOWMEM condition an ERP notification would have been sent twice causing an unpredictable behaviour of the ERP. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_erp.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index b5562f952654..c75d6f35cb5f 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -848,11 +848,17 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work) gid_pn_work); retval = zfcp_fc_ns_gid_pn(&port->erp_action); - if (retval == -ENOMEM) + if (!retval) { + port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; + goto out; + } + if (retval == -ENOMEM) { zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM); - port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP; - if (retval) - zfcp_erp_notify(&port->erp_action, 0); + goto out; + } + /* all other error condtions */ + zfcp_erp_notify(&port->erp_action, 0); +out: zfcp_port_put(port); } -- cgit v1.2.3 From 27f492ccec94b6acd8440c83bfe0515ce4db0af0 Mon Sep 17 00:00:00 2001 From: Swen Schillig Date: Mon, 13 Jul 2009 15:06:13 +0200 Subject: [SCSI] zfcp: Fix wka port processing Under certain conditions it is possible that a WKA port ist not opened within the expected timeframe of half a second. In this situation the WKA port remains in the state OPENING preventing any succeding request to open the port. This led to unrecoverable remote ports. Fixing this by always setting an appropriate WKA port status before leaving the function and removing the timeout value here since it's not needed here because the general timeout processing would deal with it if required. Signed-off-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_fc.c | 8 +++----- drivers/s390/scsi/zfcp_fsf.c | 4 ++-- 2 files changed, 5 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c index 2f0705d76b72..47daebfa7e59 100644 --- a/drivers/s390/scsi/zfcp_fc.c +++ b/drivers/s390/scsi/zfcp_fc.c @@ -79,11 +79,9 @@ static int zfcp_wka_port_get(struct zfcp_wka_port *wka_port) mutex_unlock(&wka_port->mutex); - wait_event_timeout( - wka_port->completion_wq, - wka_port->status == ZFCP_WKA_PORT_ONLINE || - wka_port->status == ZFCP_WKA_PORT_OFFLINE, - HZ >> 1); + wait_event(wka_port->completion_wq, + wka_port->status == ZFCP_WKA_PORT_ONLINE || + wka_port->status == ZFCP_WKA_PORT_OFFLINE); if (wka_port->status == ZFCP_WKA_PORT_ONLINE) { atomic_inc(&wka_port->refcount); diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c index b7e48844056a..47795fbf081f 100644 --- a/drivers/s390/scsi/zfcp_fsf.c +++ b/drivers/s390/scsi/zfcp_fsf.c @@ -1627,10 +1627,10 @@ static void zfcp_fsf_open_wka_port_handler(struct zfcp_fsf_req *req) case FSF_ACCESS_DENIED: wka_port->status = ZFCP_WKA_PORT_OFFLINE; break; - case FSF_PORT_ALREADY_OPEN: - break; case FSF_GOOD: wka_port->handle = header->port_handle; + /* fall through */ + case FSF_PORT_ALREADY_OPEN: wka_port->status = ZFCP_WKA_PORT_ONLINE; } out: -- cgit v1.2.3 From a11a52be115889a5d1f738ed2e154807bceed4ee Mon Sep 17 00:00:00 2001 From: Christof Schmitt Date: Mon, 13 Jul 2009 15:06:14 +0200 Subject: [SCSI] zfcp: Fix tracing of request id for abort requests The trace record for SCSI abort requests has a field for the request id of the request to be aborted. Put the real request id instead of zero. Reviewed-by: Swen Schillig Signed-off-by: Christof Schmitt Signed-off-by: James Bottomley --- drivers/s390/scsi/zfcp_scsi.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c index ba32709921a4..6925a1784682 100644 --- a/drivers/s390/scsi/zfcp_scsi.c +++ b/drivers/s390/scsi/zfcp_scsi.c @@ -167,20 +167,21 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) struct zfcp_unit *unit = scpnt->device->hostdata; struct zfcp_fsf_req *old_req, *abrt_req; unsigned long flags; - unsigned long old_req_id = (unsigned long) scpnt->host_scribble; + unsigned long old_reqid = (unsigned long) scpnt->host_scribble; int retval = SUCCESS; int retry = 3; + char *dbf_tag; /* avoid race condition between late normal completion and abort */ write_lock_irqsave(&adapter->abort_lock, flags); spin_lock(&adapter->req_list_lock); - old_req = zfcp_reqlist_find(adapter, old_req_id); + old_req = zfcp_reqlist_find(adapter, old_reqid); spin_unlock(&adapter->req_list_lock); if (!old_req) { write_unlock_irqrestore(&adapter->abort_lock, flags); zfcp_scsi_dbf_event_abort("lte1", adapter, scpnt, NULL, - old_req_id); + old_reqid); return FAILED; /* completion could be in progress */ } old_req->data = NULL; @@ -189,7 +190,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) write_unlock_irqrestore(&adapter->abort_lock, flags); while (retry--) { - abrt_req = zfcp_fsf_abort_fcp_command(old_req_id, unit); + abrt_req = zfcp_fsf_abort_fcp_command(old_reqid, unit); if (abrt_req) break; @@ -197,7 +198,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) if (!(atomic_read(&adapter->status) & ZFCP_STATUS_COMMON_RUNNING)) { zfcp_scsi_dbf_event_abort("nres", adapter, scpnt, NULL, - old_req_id); + old_reqid); return SUCCESS; } } @@ -208,13 +209,14 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt) abrt_req->status & ZFCP_STATUS_FSFREQ_COMPLETED); if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTSUCCEEDED) - zfcp_scsi_dbf_event_abort("okay", adapter, scpnt, abrt_req, 0); + dbf_tag = "okay"; else if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTNOTNEEDED) - zfcp_scsi_dbf_event_abort("lte2", adapter, scpnt, abrt_req, 0); + dbf_tag = "lte2"; else { - zfcp_scsi_dbf_event_abort("fail", adapter, scpnt, abrt_req, 0); + dbf_tag = "fail"; retval = FAILED; } + zfcp_scsi_dbf_event_abort(dbf_tag, adapter, scpnt, abrt_req, old_reqid); zfcp_fsf_req_free(abrt_req); return retval; } -- cgit v1.2.3 From 6187c242089d334102be76427a5a020240e6c19a Mon Sep 17 00:00:00 2001 From: Mike Christie Date: Wed, 15 Jul 2009 15:02:57 -0500 Subject: [SCSI] libiscsi: disable bh in and abort handler. The session lock can be held in the scsi eh thread or the completion paths run from the net softirq. This disables bhs in iscsi_eh_abort when taking the session lock. Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/libiscsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c index 716cc344c5df..a751f6230c22 100644 --- a/drivers/scsi/libiscsi.c +++ b/drivers/scsi/libiscsi.c @@ -1974,10 +1974,10 @@ int iscsi_eh_abort(struct scsi_cmnd *sc) * good and have never sent us a successful tmf response * then sent more data for the cmd. */ - spin_lock(&session->lock); + spin_lock_bh(&session->lock); fail_scsi_task(task, DID_ABORT); conn->tmf_state = TMF_INITIAL; - spin_unlock(&session->lock); + spin_unlock_bh(&session->lock); iscsi_start_tx(conn); goto success_unlocked; case TMF_TIMEDOUT: -- cgit v1.2.3 From 94bced3c1b371014cbd187f2df5539b13a0e3b90 Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:02:58 -0500 Subject: [SCSI] qla4xxx: Correct Extended Sense Data Errors Fixed sense data errors occurring above the first 32 bytes, as required by some third party applications. Sense data in the first 32 bytes has always been correct. Patch updated to use srb data variables instead of scsi command scratchpad data area, as scratchpad area is already used. Also, corrected debug print alignment bug in dump_buffer routine. Changed KERN_DEBUG to KERN_INFO in printk statements in this routine. Changed version number to 5.01.00-k9 Signed-off-by: Karen Higgins [michaelc: fixed checkpath.pl errors] Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_dbg.c | 15 ++-- drivers/scsi/qla4xxx/ql4_def.h | 7 ++ drivers/scsi/qla4xxx/ql4_fw.h | 7 ++ drivers/scsi/qla4xxx/ql4_isr.c | 145 +++++++++++++++++++++++++------------ drivers/scsi/qla4xxx/ql4_version.h | 2 +- 5 files changed, 122 insertions(+), 54 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/qla4xxx/ql4_dbg.c b/drivers/scsi/qla4xxx/ql4_dbg.c index fcc184cd066d..cbceb0ebabf7 100644 --- a/drivers/scsi/qla4xxx/ql4_dbg.c +++ b/drivers/scsi/qla4xxx/ql4_dbg.c @@ -15,19 +15,18 @@ void qla4xxx_dump_buffer(void *b, uint32_t size) uint32_t cnt; uint8_t *c = b; - printk(" 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh " + printk(" 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh " "Fh\n"); printk("------------------------------------------------------------" "--\n"); - for (cnt = 0; cnt < size; cnt++, c++) { - printk(KERN_DEBUG "%02x", *c); - if (!(cnt % 16)) - printk(KERN_DEBUG "\n"); + for (cnt = 0; cnt < size; c++) { + printk(KERN_INFO "%02x", *c); + if (!(++cnt % 16)) + printk(KERN_INFO "\n"); else - printk(KERN_DEBUG " "); + printk(KERN_INFO " "); } - if (cnt % 16) - printk(KERN_DEBUG "\n"); + printk(KERN_INFO "\n"); } diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h index b586f27c3bd4..963e8553d210 100644 --- a/drivers/scsi/qla4xxx/ql4_def.h +++ b/drivers/scsi/qla4xxx/ql4_def.h @@ -184,6 +184,11 @@ struct srb { uint16_t cc_stat; u_long r_start; /* Time we recieve a cmd from OS */ u_long u_start; /* Time when we handed the cmd to F/W */ + + /* Used for extended sense / status continuation */ + uint8_t *req_sense_ptr; + uint16_t req_sense_len; + uint16_t reserved2; }; /* @@ -436,6 +441,8 @@ struct scsi_qla_host { /* Map ddb_list entry by FW ddb index */ struct ddb_entry *fw_ddb_index_map[MAX_DDB_ENTRIES]; + /* Saved srb for status continuation entry processing */ + struct srb *status_srb; }; static inline int is_qla4010(struct scsi_qla_host *ha) diff --git a/drivers/scsi/qla4xxx/ql4_fw.h b/drivers/scsi/qla4xxx/ql4_fw.h index 1b667a70cffa..9cd7a608df38 100644 --- a/drivers/scsi/qla4xxx/ql4_fw.h +++ b/drivers/scsi/qla4xxx/ql4_fw.h @@ -572,6 +572,7 @@ struct conn_event_log_entry { *************************************************************************/ #define IOCB_MAX_CDB_LEN 16 /* Bytes in a CBD */ #define IOCB_MAX_SENSEDATA_LEN 32 /* Bytes of sense data */ +#define IOCB_MAX_EXT_SENSEDATA_LEN 60 /* Bytes of extended sense data */ /* IOCB header structure */ struct qla4_header { @@ -733,6 +734,12 @@ struct status_entry { }; +/* Status Continuation entry */ +struct status_cont_entry { + struct qla4_header hdr; /* 00-03 */ + uint8_t ext_sense_data[IOCB_MAX_EXT_SENSEDATA_LEN]; /* 04-63 */ +}; + struct passthru0 { struct qla4_header hdr; /* 00-03 */ uint32_t handle; /* 04-07 */ diff --git a/drivers/scsi/qla4xxx/ql4_isr.c b/drivers/scsi/qla4xxx/ql4_isr.c index 799120fcb9be..8025ee16588e 100644 --- a/drivers/scsi/qla4xxx/ql4_isr.c +++ b/drivers/scsi/qla4xxx/ql4_isr.c @@ -10,6 +10,98 @@ #include "ql4_dbg.h" #include "ql4_inline.h" +/** + * qla4xxx_copy_sense - copy sense data into cmd sense buffer + * @ha: Pointer to host adapter structure. + * @sts_entry: Pointer to status entry structure. + * @srb: Pointer to srb structure. + **/ +static void qla4xxx_copy_sense(struct scsi_qla_host *ha, + struct status_entry *sts_entry, + struct srb *srb) +{ + struct scsi_cmnd *cmd = srb->cmd; + uint16_t sense_len; + + memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); + sense_len = le16_to_cpu(sts_entry->senseDataByteCnt); + if (sense_len == 0) + return; + + /* Save total available sense length, + * not to exceed cmd's sense buffer size */ + sense_len = min_t(uint16_t, sense_len, SCSI_SENSE_BUFFERSIZE); + srb->req_sense_ptr = cmd->sense_buffer; + srb->req_sense_len = sense_len; + + /* Copy sense from sts_entry pkt */ + sense_len = min_t(uint16_t, sense_len, IOCB_MAX_SENSEDATA_LEN); + memcpy(cmd->sense_buffer, sts_entry->senseData, sense_len); + + DEBUG2(printk(KERN_INFO "scsi%ld:%d:%d:%d: %s: sense key = %x, " + "ASL= %02x, ASC/ASCQ = %02x/%02x\n", ha->host_no, + cmd->device->channel, cmd->device->id, + cmd->device->lun, __func__, + sts_entry->senseData[2] & 0x0f, + sts_entry->senseData[7], + sts_entry->senseData[12], + sts_entry->senseData[13])); + + DEBUG5(qla4xxx_dump_buffer(cmd->sense_buffer, sense_len)); + srb->flags |= SRB_GOT_SENSE; + + /* Update srb, in case a sts_cont pkt follows */ + srb->req_sense_ptr += sense_len; + srb->req_sense_len -= sense_len; + if (srb->req_sense_len != 0) + ha->status_srb = srb; + else + ha->status_srb = NULL; +} + +/** + * qla4xxx_status_cont_entry - Process a Status Continuations entry. + * @ha: SCSI driver HA context + * @sts_cont: Entry pointer + * + * Extended sense data. + */ +static void +qla4xxx_status_cont_entry(struct scsi_qla_host *ha, + struct status_cont_entry *sts_cont) +{ + struct srb *srb = ha->status_srb; + struct scsi_cmnd *cmd; + uint8_t sense_len; + + if (srb == NULL) + return; + + cmd = srb->cmd; + if (cmd == NULL) { + DEBUG2(printk(KERN_INFO "scsi%ld: %s: Cmd already returned " + "back to OS srb=%p srb->state:%d\n", ha->host_no, + __func__, srb, srb->state)); + ha->status_srb = NULL; + return; + } + + /* Copy sense data. */ + sense_len = min_t(uint16_t, srb->req_sense_len, + IOCB_MAX_EXT_SENSEDATA_LEN); + memcpy(srb->req_sense_ptr, sts_cont->ext_sense_data, sense_len); + DEBUG5(qla4xxx_dump_buffer(srb->req_sense_ptr, sense_len)); + + srb->req_sense_ptr += sense_len; + srb->req_sense_len -= sense_len; + + /* Place command on done queue. */ + if (srb->req_sense_len == 0) { + qla4xxx_srb_compl(ha, srb); + ha->status_srb = NULL; + } +} + /** * qla4xxx_status_entry - processes status IOCBs * @ha: Pointer to host adapter structure. @@ -23,7 +115,6 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, struct srb *srb; struct ddb_entry *ddb_entry; uint32_t residual; - uint16_t sensebytecnt; srb = qla4xxx_del_from_active_array(ha, le32_to_cpu(sts_entry->handle)); if (!srb) { @@ -92,24 +183,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, break; /* Copy Sense Data into sense buffer. */ - memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); - - sensebytecnt = le16_to_cpu(sts_entry->senseDataByteCnt); - if (sensebytecnt == 0) - break; - - memcpy(cmd->sense_buffer, sts_entry->senseData, - min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE)); - - DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, " - "ASC/ASCQ = %02x/%02x\n", ha->host_no, - cmd->device->channel, cmd->device->id, - cmd->device->lun, __func__, - sts_entry->senseData[2] & 0x0f, - sts_entry->senseData[12], - sts_entry->senseData[13])); - - srb->flags |= SRB_GOT_SENSE; + qla4xxx_copy_sense(ha, sts_entry, srb); break; case SCS_INCOMPLETE: @@ -176,23 +250,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, break; /* Copy Sense Data into sense buffer. */ - memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); - - sensebytecnt = - le16_to_cpu(sts_entry->senseDataByteCnt); - if (sensebytecnt == 0) - break; - - memcpy(cmd->sense_buffer, sts_entry->senseData, - min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE)); - - DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, " - "ASC/ASCQ = %02x/%02x\n", ha->host_no, - cmd->device->channel, cmd->device->id, - cmd->device->lun, __func__, - sts_entry->senseData[2] & 0x0f, - sts_entry->senseData[12], - sts_entry->senseData[13])); + qla4xxx_copy_sense(ha, sts_entry, srb); } else { /* * If RISC reports underrun and target does not @@ -268,9 +326,10 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha, status_entry_exit: - /* complete the request */ + /* complete the request, if not waiting for status_continuation pkt */ srb->cc_stat = sts_entry->completionStatus; - qla4xxx_srb_compl(ha, srb); + if (ha->status_srb == NULL) + qla4xxx_srb_compl(ha, srb); } /** @@ -305,10 +364,7 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha) /* process entry */ switch (sts_entry->hdr.entryType) { case ET_STATUS: - /* - * Common status - Single completion posted in single - * IOSB. - */ + /* Common status */ qla4xxx_status_entry(ha, sts_entry); break; @@ -316,9 +372,8 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha) break; case ET_STATUS_CONTINUATION: - /* Just throw away the status continuation entries */ - DEBUG2(printk("scsi%ld: %s: Status Continuation entry " - "- ignoring\n", ha->host_no, __func__)); + qla4xxx_status_cont_entry(ha, + (struct status_cont_entry *) sts_entry); break; case ET_COMMAND: diff --git a/drivers/scsi/qla4xxx/ql4_version.h b/drivers/scsi/qla4xxx/ql4_version.h index ab984cb89cea..6980cb279c81 100644 --- a/drivers/scsi/qla4xxx/ql4_version.h +++ b/drivers/scsi/qla4xxx/ql4_version.h @@ -5,5 +5,5 @@ * See LICENSE.qla4xxx for copyright and licensing details. */ -#define QLA4XXX_DRIVER_VERSION "5.01.00-k8" +#define QLA4XXX_DRIVER_VERSION "5.01.00-k9" -- cgit v1.2.3 From 5c656af7e4edfe44c85034d6fa7002909f9c3c59 Mon Sep 17 00:00:00 2001 From: Mike Christie Date: Wed, 15 Jul 2009 15:02:59 -0500 Subject: [SCSI] qla4xxx: add timeout handler Recently dm-multipath began calling blk_abort_queue. This causes all the commands/request running on the path to have the timeout function called. If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually get this error and begin to call the cmd timeout handler. qla4xxx currently does not set a timed out handler and so the default one could return BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all paths on the host when only one path is affected. For software and offload iscsi we have a timed out handler already. This patch adds a driver specific one to qla4xxx because there are some ddb->state and session->state and command completion races that are better handled in the LLD. This also handles the problem where if the session is down, we do not need the scsi eh to run until the transport code has tried to reconnect us. Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) (limited to 'drivers') diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index ec9da6ce8489..6841883b3611 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -66,6 +66,7 @@ static int qla4xxx_sess_get_param(struct iscsi_cls_session *sess, static int qla4xxx_host_get_param(struct Scsi_Host *shost, enum iscsi_host_param param, char *buf); static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session); +static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc); /* * SCSI host template entry points @@ -89,6 +90,7 @@ static struct scsi_host_template qla4xxx_driver_template = { .eh_device_reset_handler = qla4xxx_eh_device_reset, .eh_target_reset_handler = qla4xxx_eh_target_reset, .eh_host_reset_handler = qla4xxx_eh_host_reset, + .eh_timed_out = qla4xxx_eh_cmd_timed_out, .slave_configure = qla4xxx_slave_configure, .slave_alloc = qla4xxx_slave_alloc, @@ -124,6 +126,21 @@ static struct iscsi_transport qla4xxx_iscsi_transport = { static struct scsi_transport_template *qla4xxx_scsi_transport; +static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc) +{ + struct iscsi_cls_session *session; + struct ddb_entry *ddb_entry; + + session = starget_to_session(scsi_target(sc->device)); + ddb_entry = session->dd_data; + + /* if we are not logged in then the LLD is going to clean up the cmd */ + if (atomic_read(&ddb_entry->state) != DDB_STATE_ONLINE) + return BLK_EH_RESET_TIMER; + else + return BLK_EH_NOT_HANDLED; +} + static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session) { struct ddb_entry *ddb_entry = session->dd_data; -- cgit v1.2.3 From dca05c4c07c48da0509708d9e562578d269e90e5 Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:00 -0500 Subject: [SCSI] qla4xxx: Fix Driver Fault Recovery Completion Fixed driver bug where adapter recovery did not complete if there were outstanding commands detected on that host adapter. Signed-off-by: Karen Higgins Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index 6841883b3611..e1cc0d21d890 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -921,18 +921,17 @@ static int qla4xxx_recover_adapter(struct scsi_qla_host *ha, /* Flush any pending ddb changed AENs */ qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS); + qla4xxx_flush_active_srbs(ha); + /* Reset the firmware. If successful, function * returns with ISP interrupts enabled. */ - if (status == QLA_SUCCESS) { - DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n", - ha->host_no, __func__)); - qla4xxx_flush_active_srbs(ha); - if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS) - status = qla4xxx_soft_reset(ha); - else - status = QLA_ERROR; - } + DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n", + ha->host_no, __func__)); + if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS) + status = qla4xxx_soft_reset(ha); + else + status = QLA_ERROR; /* Flush any pending ddb changed AENs */ qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS); @@ -1661,7 +1660,7 @@ static int qla4xxx_eh_host_reset(struct scsi_cmnd *cmd) ha = (struct scsi_qla_host *) cmd->device->host->hostdata; dev_info(&ha->pdev->dev, - "scsi(%ld:%d:%d:%d): ADAPTER RESET ISSUED.\n", ha->host_no, + "scsi(%ld:%d:%d:%d): HOST RESET ISSUED.\n", ha->host_no, cmd->device->channel, cmd->device->id, cmd->device->lun); if (qla4xxx_wait_for_hba_online(ha) != QLA_SUCCESS) { -- cgit v1.2.3 From 612f73488785829d4f34aad00bfe30b904c94c9e Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:01 -0500 Subject: [SCSI] qla4xxx: Fix srb lookup in qla4xxx_eh_device_reset eh_device_reset may be called from scsi error handler or sg_reset, etc. When called from sg_reset, there will not be an associated srb. The driver should lookup the corresponding device handle given information from the supplied cmd structure and should not assume that there exists an srb. Signed-off-by: Karen Higgins Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_os.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index e1cc0d21d890..40e3cafb3a9c 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -1543,11 +1543,9 @@ static int qla4xxx_eh_device_reset(struct scsi_cmnd *cmd) { struct scsi_qla_host *ha = to_qla_host(cmd->device->host); struct ddb_entry *ddb_entry = cmd->device->hostdata; - struct srb *sp; int ret = FAILED, stat; - sp = (struct srb *) cmd->SCp.ptr; - if (!sp || !ddb_entry) + if (!ddb_entry) return ret; dev_info(&ha->pdev->dev, -- cgit v1.2.3 From 16ed55f9de6743ceece9bf528362cadff10f1c5c Mon Sep 17 00:00:00 2001 From: Karen Higgins Date: Wed, 15 Jul 2009 15:03:02 -0500 Subject: [SCSI] qla4xxx: Remove hiwat code so scsi eh does not get escalated when we can make progress Removed unnecessary hiwat code to free up the number available IOCBs. Eliminates unnecessary eh_ escalations due to inability to obtain IOCB pkt for marker. v2. - Remove define not used anymore and fix req_q_coun accounting. Signed-off-by: Karen Higgins [michaelc: ported patch from qlogic.com driver to upstream] Signed-off-by: Mike Christie Signed-off-by: James Bottomley --- drivers/scsi/qla4xxx/ql4_def.h | 2 - drivers/scsi/qla4xxx/ql4_iocb.c | 133 ++++++++++++++++++---------------------- drivers/scsi/qla4xxx/ql4_mbx.c | 10 --- 3 files changed, 60 insertions(+), 85 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h index 963e8553d210..81b5f29254e2 100644 --- a/drivers/scsi/qla4xxx/ql4_def.h +++ b/drivers/scsi/qla4xxx/ql4_def.h @@ -100,7 +100,6 @@ #define MAX_SRBS MAX_CMDS_TO_RISC #define MBOX_AEN_REG_COUNT 5 #define MAX_INIT_RETRIES 5 -#define IOCB_HIWAT_CUSHION 16 /* * Buffer sizes @@ -307,7 +306,6 @@ struct scsi_qla_host { uint32_t tot_ddbs; uint16_t iocb_cnt; - uint16_t iocb_hiwat; /* SRB cache. */ #define SRB_MIN_REQ 128 diff --git a/drivers/scsi/qla4xxx/ql4_iocb.c b/drivers/scsi/qla4xxx/ql4_iocb.c index 912a67494adf..e0c32159749c 100644 --- a/drivers/scsi/qla4xxx/ql4_iocb.c +++ b/drivers/scsi/qla4xxx/ql4_iocb.c @@ -10,9 +10,42 @@ #include "ql4_dbg.h" #include "ql4_inline.h" - #include +static int +qla4xxx_space_in_req_ring(struct scsi_qla_host *ha, uint16_t req_cnt) +{ + uint16_t cnt; + + /* Calculate number of free request entries. */ + if ((req_cnt + 2) >= ha->req_q_count) { + cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); + if (ha->request_in < cnt) + ha->req_q_count = cnt - ha->request_in; + else + ha->req_q_count = REQUEST_QUEUE_DEPTH - + (ha->request_in - cnt); + } + + /* Check if room for request in request ring. */ + if ((req_cnt + 2) < ha->req_q_count) + return 1; + else + return 0; +} + +static void qla4xxx_advance_req_ring_ptr(struct scsi_qla_host *ha) +{ + /* Advance request queue pointer */ + if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) { + ha->request_in = 0; + ha->request_ptr = ha->request_ring; + } else { + ha->request_in++; + ha->request_ptr++; + } +} + /** * qla4xxx_get_req_pkt - returns a valid entry in request queue. * @ha: Pointer to host adapter structure. @@ -26,35 +59,18 @@ static int qla4xxx_get_req_pkt(struct scsi_qla_host *ha, struct queue_entry **queue_entry) { - uint16_t request_in; - uint8_t status = QLA_SUCCESS; - - *queue_entry = ha->request_ptr; + uint16_t req_cnt = 1; - /* get the latest request_in and request_out index */ - request_in = ha->request_in; - ha->request_out = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); - - /* Advance request queue pointer and check for queue full */ - if (request_in == (REQUEST_QUEUE_DEPTH - 1)) { - request_in = 0; - ha->request_ptr = ha->request_ring; - } else { - request_in++; - ha->request_ptr++; - } - - /* request queue is full, try again later */ - if ((ha->iocb_cnt + 1) >= ha->iocb_hiwat) { - /* restore request pointer */ - ha->request_ptr = *queue_entry; - status = QLA_ERROR; - } else { - ha->request_in = request_in; + if (qla4xxx_space_in_req_ring(ha, req_cnt)) { + *queue_entry = ha->request_ptr; memset(*queue_entry, 0, sizeof(**queue_entry)); + + qla4xxx_advance_req_ring_ptr(ha); + ha->req_q_count -= req_cnt; + return QLA_SUCCESS; } - return status; + return QLA_ERROR; } /** @@ -100,21 +116,14 @@ exit_send_marker: return status; } -static struct continuation_t1_entry* qla4xxx_alloc_cont_entry( - struct scsi_qla_host *ha) +static struct continuation_t1_entry * +qla4xxx_alloc_cont_entry(struct scsi_qla_host *ha) { struct continuation_t1_entry *cont_entry; cont_entry = (struct continuation_t1_entry *)ha->request_ptr; - /* Advance request queue pointer */ - if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) { - ha->request_in = 0; - ha->request_ptr = ha->request_ring; - } else { - ha->request_in++; - ha->request_ptr++; - } + qla4xxx_advance_req_ring_ptr(ha); /* Load packet defaults */ cont_entry->hdr.entryType = ET_CONTINUE; @@ -197,13 +206,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) struct scsi_cmnd *cmd = srb->cmd; struct ddb_entry *ddb_entry; struct command_t3_entry *cmd_entry; - int nseg; uint16_t tot_dsds; uint16_t req_cnt; - unsigned long flags; - uint16_t cnt; uint32_t index; char tag[2]; @@ -217,6 +223,19 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) index = (uint32_t)cmd->request->tag; + /* + * Check to see if adapter is online before placing request on + * request queue. If a reset occurs and a request is in the queue, + * the firmware will still attempt to process the request, retrieving + * garbage for pointers. + */ + if (!test_bit(AF_ONLINE, &ha->flags)) { + DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! " + "Do not issue command.\n", + ha->host_no, __func__)); + goto queuing_error; + } + /* Calculate the number of request entries needed. */ nseg = scsi_dma_map(cmd); if (nseg < 0) @@ -224,17 +243,7 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) tot_dsds = nseg; req_cnt = qla4xxx_calc_request_entries(tot_dsds); - - if (ha->req_q_count < (req_cnt + 2)) { - cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out); - if (ha->request_in < cnt) - ha->req_q_count = cnt - ha->request_in; - else - ha->req_q_count = REQUEST_QUEUE_DEPTH - - (ha->request_in - cnt); - } - - if (ha->req_q_count < (req_cnt + 2)) + if (!qla4xxx_space_in_req_ring(ha, req_cnt)) goto queuing_error; /* total iocbs active */ @@ -286,32 +295,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb) break; } - - /* Advance request queue pointer */ - ha->request_in++; - if (ha->request_in == REQUEST_QUEUE_DEPTH) { - ha->request_in = 0; - ha->request_ptr = ha->request_ring; - } else - ha->request_ptr++; - - + qla4xxx_advance_req_ring_ptr(ha); qla4xxx_build_scsi_iocbs(srb, cmd_entry, tot_dsds); wmb(); - /* - * Check to see if adapter is online before placing request on - * request queue. If a reset occurs and a request is in the queue, - * the firmware will still attempt to process the request, retrieving - * garbage for pointers. - */ - if (!test_bit(AF_ONLINE, &ha->flags)) { - DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! " - "Do not issue command.\n", - ha->host_no, __func__)); - goto queuing_error; - } - srb->cmd->host_scribble = (unsigned char *)srb; /* update counters */ diff --git a/drivers/scsi/qla4xxx/ql4_mbx.c b/drivers/scsi/qla4xxx/ql4_mbx.c index 051b0f5e8c8e..09d6d4b76f39 100644 --- a/drivers/scsi/qla4xxx/ql4_mbx.c +++ b/drivers/scsi/qla4xxx/ql4_mbx.c @@ -385,16 +385,6 @@ int qla4xxx_get_firmware_status(struct scsi_qla_host * ha) mbox_sts[0])); return QLA_ERROR; } - - /* High-water mark of IOCBs */ - ha->iocb_hiwat = mbox_sts[2]; - if (ha->iocb_hiwat > IOCB_HIWAT_CUSHION) - ha->iocb_hiwat -= IOCB_HIWAT_CUSHION; - else - dev_info(&ha->pdev->dev, "WARNING!!! You have less than %d " - "firmware IOCBs available (%d).\n", - IOCB_HIWAT_CUSHION, ha->iocb_hiwat); - return QLA_SUCCESS; } -- cgit v1.2.3 From a0cc1ecc098e31d03b3265712a3e280a7fabf438 Mon Sep 17 00:00:00 2001 From: Vasu Dev Date: Tue, 28 Jul 2009 17:33:37 -0700 Subject: [SCSI] libfc: fix a circular locking warning during sending RRQ Currently the fc_exch_rrq is called with fc_exch's ex_lock held. The fc_exch_rrq allocates new exch and that requires taking ex_lock again after EM lock. This locking order causes warning, see more details on this warning at :- http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html This patch fixes this by dropping the ex_lock before calling fc_exch_rrq(). The fc_exch_rrq needs to grab ex_lock lock again to schedule RRQ retry and in the meanwhile fc_exch_reset could occur before ex_lock is grabbed inside fc_exch_rrq. So to handle this case, this patch adds additional check to detect fc_exch_reset after ex_lock acquired and in case the fc_exch_reset occurred then abandons the RRQ retry and releases the exch. Signed-off-by: Vasu Dev Signed-off-by: Robert Love Signed-off-by: James Bottomley --- drivers/scsi/libfc/fc_exch.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/libfc/fc_exch.c b/drivers/scsi/libfc/fc_exch.c index 2bc22be5f849..145ab9ba55ea 100644 --- a/drivers/scsi/libfc/fc_exch.c +++ b/drivers/scsi/libfc/fc_exch.c @@ -415,9 +415,9 @@ static void fc_exch_timeout(struct work_struct *work) e_stat = ep->esb_stat; if (e_stat & ESB_ST_COMPLETE) { ep->esb_stat = e_stat & ~ESB_ST_REC_QUAL; + spin_unlock_bh(&ep->ex_lock); if (e_stat & ESB_ST_REC_QUAL) fc_exch_rrq(ep); - spin_unlock_bh(&ep->ex_lock); goto done; } else { resp = ep->resp; @@ -1624,14 +1624,14 @@ static void fc_exch_rrq(struct fc_exch *ep) struct fc_lport *lp; struct fc_els_rrq *rrq; struct fc_frame *fp; - struct fc_seq *rrq_sp; u32 did; lp = ep->lp; fp = fc_frame_alloc(lp, sizeof(*rrq)); if (!fp) - return; + goto retry; + rrq = fc_frame_payload_get(fp, sizeof(*rrq)); memset(rrq, 0, sizeof(*rrq)); rrq->rrq_cmd = ELS_RRQ; @@ -1647,13 +1647,20 @@ static void fc_exch_rrq(struct fc_exch *ep) fc_host_port_id(lp->host), FC_TYPE_ELS, FC_FC_FIRST_SEQ | FC_FC_END_SEQ | FC_FC_SEQ_INIT, 0); - rrq_sp = fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep, - lp->e_d_tov); - if (!rrq_sp) { - ep->esb_stat |= ESB_ST_REC_QUAL; - fc_exch_timer_set_locked(ep, ep->r_a_tov); + if (fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep, lp->e_d_tov)) + return; + +retry: + spin_lock_bh(&ep->ex_lock); + if (ep->state & (FC_EX_RST_CLEANUP | FC_EX_DONE)) { + spin_unlock_bh(&ep->ex_lock); + /* drop hold for rec qual */ + fc_exch_release(ep); return; } + ep->esb_stat |= ESB_ST_REC_QUAL; + fc_exch_timer_set_locked(ep, ep->r_a_tov); + spin_unlock_bh(&ep->ex_lock); } -- cgit v1.2.3 From 19252de6818ced0def0551d64a0a2975f52a523d Mon Sep 17 00:00:00 2001 From: Tom Peng Date: Fri, 17 Jul 2009 16:02:04 +0800 Subject: [SCSI] libsas: fix wide port hotplug issues Hotplug of phys which form wide ports simply does not work at the moment. Fix this by adding checks at the hotplug points to see if the attached sas address of the phy already exists (in which case it's part of a wide port) and act accordingly. Signed-off-by: Tom Peng Signed-off-by: Jack Wang Signed-off-by: Lindar Liu Signed-off-by: Kevin Ao [jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower case to fix a ppc64 compile error in linux-next] Signed-off-by: James Bottomley --- drivers/scsi/libsas/sas_expander.c | 147 +++++++++++++++++++++++++++---------- 1 file changed, 107 insertions(+), 40 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c index 54fa1e42dc4d..b3381959acce 100644 --- a/drivers/scsi/libsas/sas_expander.c +++ b/drivers/scsi/libsas/sas_expander.c @@ -766,6 +766,7 @@ static int sas_ex_join_wide_port(struct domain_device *parent, int phy_id) if (!memcmp(phy->attached_sas_addr, ephy->attached_sas_addr, SAS_ADDR_SIZE) && ephy->port) { sas_port_add_phy(ephy->port, phy->phy); + phy->port = ephy->port; phy->phy_state = PHY_DEVICE_DISCOVERED; return 0; } @@ -945,11 +946,21 @@ static int sas_ex_discover_dev(struct domain_device *dev, int phy_id) if (ex->ex_phy[i].phy_state == PHY_VACANT || ex->ex_phy[i].phy_state == PHY_NOT_PRESENT) continue; - + /* + * Due to races, the phy might not get added to the + * wide port, so we add the phy to the wide port here. + */ if (SAS_ADDR(ex->ex_phy[i].attached_sas_addr) == - SAS_ADDR(child->sas_addr)) + SAS_ADDR(child->sas_addr)) { ex->ex_phy[i].phy_state= PHY_DEVICE_DISCOVERED; + res = sas_ex_join_wide_port(dev, i); + if (!res) + SAS_DPRINTK("Attaching ex phy%d to wide port %016llx\n", + i, SAS_ADDR(ex->ex_phy[i].attached_sas_addr)); + + } } + res = 0; } return res; @@ -1598,7 +1609,7 @@ static int sas_get_phy_attached_sas_addr(struct domain_device *dev, } static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id, - int from_phy) + int from_phy, bool update) { struct expander_device *ex = &dev->ex_dev; int res = 0; @@ -1611,7 +1622,9 @@ static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id, if (res) goto out; else if (phy_change_count != ex->ex_phy[i].phy_change_count) { - ex->ex_phy[i].phy_change_count = phy_change_count; + if (update) + ex->ex_phy[i].phy_change_count = + phy_change_count; *phy_id = i; return 0; } @@ -1653,31 +1666,52 @@ out: kfree(rg_req); return res; } +/** + * sas_find_bcast_dev - find the device issue BROADCAST(CHANGE). + * @dev:domain device to be detect. + * @src_dev: the device which originated BROADCAST(CHANGE). + * + * Add self-configuration expander suport. Suppose two expander cascading, + * when the first level expander is self-configuring, hotplug the disks in + * second level expander, BROADCAST(CHANGE) will not only be originated + * in the second level expander, but also be originated in the first level + * expander (see SAS protocol SAS 2r-14, 7.11 for detail), it is to say, + * expander changed count in two level expanders will all increment at least + * once, but the phy which chang count has changed is the source device which + * we concerned. + */ static int sas_find_bcast_dev(struct domain_device *dev, struct domain_device **src_dev) { struct expander_device *ex = &dev->ex_dev; int ex_change_count = -1; + int phy_id = -1; int res; + struct domain_device *ch; res = sas_get_ex_change_count(dev, &ex_change_count); if (res) goto out; - if (ex_change_count != -1 && - ex_change_count != ex->ex_change_count) { - *src_dev = dev; - ex->ex_change_count = ex_change_count; - } else { - struct domain_device *ch; - - list_for_each_entry(ch, &ex->children, siblings) { - if (ch->dev_type == EDGE_DEV || - ch->dev_type == FANOUT_DEV) { - res = sas_find_bcast_dev(ch, src_dev); - if (src_dev) - return res; - } + if (ex_change_count != -1 && ex_change_count != ex->ex_change_count) { + /* Just detect if this expander phys phy change count changed, + * in order to determine if this expander originate BROADCAST, + * and do not update phy change count field in our structure. + */ + res = sas_find_bcast_phy(dev, &phy_id, 0, false); + if (phy_id != -1) { + *src_dev = dev; + ex->ex_change_count = ex_change_count; + SAS_DPRINTK("Expander phy change count has changed\n"); + return res; + } else + SAS_DPRINTK("Expander phys DID NOT change\n"); + } + list_for_each_entry(ch, &ex->children, siblings) { + if (ch->dev_type == EDGE_DEV || ch->dev_type == FANOUT_DEV) { + res = sas_find_bcast_dev(ch, src_dev); + if (src_dev) + return res; } } out: @@ -1700,24 +1734,26 @@ static void sas_unregister_ex_tree(struct domain_device *dev) } static void sas_unregister_devs_sas_addr(struct domain_device *parent, - int phy_id) + int phy_id, bool last) { struct expander_device *ex_dev = &parent->ex_dev; struct ex_phy *phy = &ex_dev->ex_phy[phy_id]; struct domain_device *child, *n; - - list_for_each_entry_safe(child, n, &ex_dev->children, siblings) { - if (SAS_ADDR(child->sas_addr) == - SAS_ADDR(phy->attached_sas_addr)) { - if (child->dev_type == EDGE_DEV || - child->dev_type == FANOUT_DEV) - sas_unregister_ex_tree(child); - else - sas_unregister_dev(child); - break; + if (last) { + list_for_each_entry_safe(child, n, + &ex_dev->children, siblings) { + if (SAS_ADDR(child->sas_addr) == + SAS_ADDR(phy->attached_sas_addr)) { + if (child->dev_type == EDGE_DEV || + child->dev_type == FANOUT_DEV) + sas_unregister_ex_tree(child); + else + sas_unregister_dev(child); + break; + } } + sas_disable_routing(parent, phy->attached_sas_addr); } - sas_disable_routing(parent, phy->attached_sas_addr); memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE); sas_port_delete_phy(phy->port, phy->phy); if (phy->port->num_phys == 0) @@ -1770,15 +1806,31 @@ static int sas_discover_new(struct domain_device *dev, int phy_id) { struct ex_phy *ex_phy = &dev->ex_dev.ex_phy[phy_id]; struct domain_device *child; - int res; + bool found = false; + int res, i; SAS_DPRINTK("ex %016llx phy%d new device attached\n", SAS_ADDR(dev->sas_addr), phy_id); res = sas_ex_phy_discover(dev, phy_id); if (res) goto out; + /* to support the wide port inserted */ + for (i = 0; i < dev->ex_dev.num_phys; i++) { + struct ex_phy *ex_phy_temp = &dev->ex_dev.ex_phy[i]; + if (i == phy_id) + continue; + if (SAS_ADDR(ex_phy_temp->attached_sas_addr) == + SAS_ADDR(ex_phy->attached_sas_addr)) { + found = true; + break; + } + } + if (found) { + sas_ex_join_wide_port(dev, phy_id); + return 0; + } res = sas_ex_discover_devices(dev, phy_id); - if (res) + if (!res) goto out; list_for_each_entry(child, &dev->ex_dev.children, siblings) { if (SAS_ADDR(child->sas_addr) == @@ -1793,7 +1845,7 @@ out: return res; } -static int sas_rediscover_dev(struct domain_device *dev, int phy_id) +static int sas_rediscover_dev(struct domain_device *dev, int phy_id, bool last) { struct expander_device *ex = &dev->ex_dev; struct ex_phy *phy = &ex->ex_phy[phy_id]; @@ -1804,11 +1856,11 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id) switch (res) { case SMP_RESP_NO_PHY: phy->phy_state = PHY_NOT_PRESENT; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); goto out; break; case SMP_RESP_PHY_VACANT: phy->phy_state = PHY_VACANT; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); goto out; break; case SMP_RESP_FUNC_ACC: break; @@ -1816,7 +1868,7 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id) if (SAS_ADDR(attached_sas_addr) == 0) { phy->phy_state = PHY_EMPTY; - sas_unregister_devs_sas_addr(dev, phy_id); + sas_unregister_devs_sas_addr(dev, phy_id, last); } else if (SAS_ADDR(attached_sas_addr) == SAS_ADDR(phy->attached_sas_addr)) { SAS_DPRINTK("ex %016llx phy 0x%x broadcast flutter\n", @@ -1828,12 +1880,27 @@ out: return res; } +/** + * sas_rediscover - revalidate the domain. + * @dev:domain device to be detect. + * @phy_id: the phy id will be detected. + * + * NOTE: this process _must_ quit (return) as soon as any connection + * errors are encountered. Connection recovery is done elsewhere. + * Discover process only interrogates devices in order to discover the + * domain.For plugging out, we un-register the device only when it is + * the last phy in the port, for other phys in this port, we just delete it + * from the port.For inserting, we do discovery when it is the + * first phy,for other phys in this port, we add it to the port to + * forming the wide-port. + */ static int sas_rediscover(struct domain_device *dev, const int phy_id) { struct expander_device *ex = &dev->ex_dev; struct ex_phy *changed_phy = &ex->ex_phy[phy_id]; int res = 0; int i; + bool last = true; /* is this the last phy of the port */ SAS_DPRINTK("ex %016llx phy%d originated BROADCAST(CHANGE)\n", SAS_ADDR(dev->sas_addr), phy_id); @@ -1848,13 +1915,13 @@ static int sas_rediscover(struct domain_device *dev, const int phy_id) SAS_ADDR(changed_phy->attached_sas_addr)) { SAS_DPRINTK("phy%d part of wide port with " "phy%d\n", phy_id, i); - goto out; + last = false; + break; } } - res = sas_rediscover_dev(dev, phy_id); + res = sas_rediscover_dev(dev, phy_id, last); } else res = sas_discover_new(dev, phy_id); -out: return res; } @@ -1881,7 +1948,7 @@ int sas_ex_revalidate_domain(struct domain_device *port_dev) do { phy_id = -1; - res = sas_find_bcast_phy(dev, &phy_id, i); + res = sas_find_bcast_phy(dev, &phy_id, i, true); if (phy_id == -1) break; res = sas_rediscover(dev, phy_id); -- cgit v1.2.3 From ffd4bc2a984fab40ed969163efdff321490e8032 Mon Sep 17 00:00:00 2001 From: "Martin K. Petersen" Date: Wed, 29 Jul 2009 14:06:53 -0400 Subject: [SCSI] sd: Avoid sending extended inquiry to legacy devices Some USB devices crash when we send them an inquiry with the EVPD bit set, regardless of page requested (i.e. including page 0). We only need the extended inquiry to gain access to VPD pages 0xB0 and 0xB1. These appeared in SBC2 and SBC3 respectively, so we can restrict sending the extended inquiry to devices reporting SPC3 or higher. This fixes bugzilla.kernel.org #13657. Signed-off-by: Martin K. Petersen [jejb: added comment] Signed-off-by: James Bottomley --- drivers/scsi/sd.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c index 5616cd780ff3..b7b9fec67a98 100644 --- a/drivers/scsi/sd.c +++ b/drivers/scsi/sd.c @@ -1840,6 +1840,18 @@ static void sd_read_block_characteristics(struct scsi_disk *sdkp) kfree(buffer); } +static int sd_try_extended_inquiry(struct scsi_device *sdp) +{ + /* + * Although VPD inquiries can go to SCSI-2 type devices, + * some USB ones crash on receiving them, and the pages + * we currently ask for are for SPC-3 and beyond + */ + if (sdp->scsi_level > SCSI_SPC_2) + return 1; + return 0; +} + /** * sd_revalidate_disk - called the first time a new disk is seen, * performs disk spin up, read_capacity, etc. @@ -1877,8 +1889,12 @@ static int sd_revalidate_disk(struct gendisk *disk) */ if (sdkp->media_present) { sd_read_capacity(sdkp, buffer); - sd_read_block_limits(sdkp); - sd_read_block_characteristics(sdkp); + + if (sd_try_extended_inquiry(sdp)) { + sd_read_block_limits(sdkp); + sd_read_block_characteristics(sdkp); + } + sd_read_write_protect_flag(sdkp, buffer); sd_read_cache_type(sdkp, buffer); sd_read_app_tag_own(sdkp, buffer); -- cgit v1.2.3 From 2b8d33f714477d1719f96459370037993520de84 Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Wed, 29 Jul 2009 11:31:18 +0800 Subject: drm/i915: Return disconnected for SDVO DVI when there's no digital EDID. The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector, it incorrectly shows sdvo dvi as connected. Signed-off-by: Ma Ling [anholt: hand-resolved against previous commit and fixed up commit message] Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_sdvo.c | 27 +++++++++++++++++++++------ 1 file changed, 21 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c index b68746f0380e..5371d9332554 100644 --- a/drivers/gpu/drm/i915/intel_sdvo.c +++ b/drivers/gpu/drm/i915/intel_sdvo.c @@ -31,6 +31,7 @@ #include "drm.h" #include "drm_crtc.h" #include "intel_drv.h" +#include "drm_edid.h" #include "i915_drm.h" #include "i915_drv.h" #include "intel_sdvo_regs.h" @@ -1477,20 +1478,35 @@ intel_sdvo_multifunc_encoder(struct intel_output *intel_output) return (caps > 1); } -static void -intel_sdvo_hdmi_sink_detect(struct drm_connector *connector) +enum drm_connector_status +intel_sdvo_hdmi_sink_detect(struct drm_connector *connector, u16 response) { struct intel_output *intel_output = to_intel_output(connector); struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv; + enum drm_connector_status status = connector_status_connected; struct edid *edid = NULL; edid = drm_get_edid(&intel_output->base, intel_output->ddc_bus); if (edid != NULL) { - sdvo_priv->is_hdmi = drm_detect_hdmi_monitor(edid); + /* Don't report the output as connected if it's a DVI-I + * connector with a non-digital EDID coming out. + */ + if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) { + if (edid->input & DRM_EDID_INPUT_DIGITAL) + sdvo_priv->is_hdmi = + drm_detect_hdmi_monitor(edid); + else + status = connector_status_disconnected; + } + kfree(edid); intel_output->base.display_info.raw_edid = NULL; - } + + } else if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) + status = connector_status_disconnected; + + return status; } static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector) @@ -1518,8 +1534,7 @@ static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connect return connector_status_unknown; sdvo_priv->attached_output = response; } - intel_sdvo_hdmi_sink_detect(connector); - return connector_status_connected; + return intel_sdvo_hdmi_sink_detect(connector, response); } static void intel_sdvo_get_ddc_modes(struct drm_connector *connector) -- cgit v1.2.3 From 0c2e39525b3b53a97a0202c5f35058147e53977e Mon Sep 17 00:00:00 2001 From: "ling.ma@intel.com" Date: Fri, 17 Jul 2009 11:44:30 +0800 Subject: drm/i915: Add support for dual-channel LVDS on 8xx. This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115. Signed-off-by: Ma Ling Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/intel_display.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 1da7b0b9ed31..d6fce2133413 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -90,7 +90,7 @@ struct intel_limit { #define I8XX_P2_SLOW 4 #define I8XX_P2_FAST 2 #define I8XX_P2_LVDS_SLOW 14 -#define I8XX_P2_LVDS_FAST 14 /* No fast option */ +#define I8XX_P2_LVDS_FAST 7 #define I8XX_P2_SLOW_LIMIT 165000 #define I9XX_DOT_MIN 20000 -- cgit v1.2.3 From a541f8401d8e9113a89ee902cb8d8e412d6d3569 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Wed, 29 Jul 2009 08:49:52 +0000 Subject: iscsi: Use GFP_ATOMIC in iscsi_offload_mesg(). Changing to GFP_ATOMIC because the only caller in cnic/bnx2i may be calling this function while holding spin_lock. This problem was discovered by Mike Christie. Signed-off-by: Michael Chan Acked-by: Mike Christie Signed-off-by: David S. Miller --- drivers/scsi/scsi_transport_iscsi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/scsi/scsi_transport_iscsi.c b/drivers/scsi/scsi_transport_iscsi.c index 783e33c65eb7..b47240ca4b19 100644 --- a/drivers/scsi/scsi_transport_iscsi.c +++ b/drivers/scsi/scsi_transport_iscsi.c @@ -990,7 +990,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost, struct iscsi_uevent *ev; int len = NLMSG_SPACE(sizeof(*ev) + data_size); - skb = alloc_skb(len, GFP_NOIO); + skb = alloc_skb(len, GFP_ATOMIC); if (!skb) { printk(KERN_ERR "can not deliver iscsi offload message:OOM\n"); return -ENOMEM; @@ -1012,7 +1012,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost, memcpy((char *)ev + sizeof(*ev), data, data_size); - return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_NOIO); + return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_ATOMIC); } EXPORT_SYMBOL_GPL(iscsi_offload_mesg); -- cgit v1.2.3 From 3d54015b750e5d5e950a1dcee2735387fd4b6e1a Mon Sep 17 00:00:00 2001 From: roel kluin Date: Thu, 30 Jul 2009 00:26:32 +0000 Subject: 3c515: Write outside array bounds if dev_alloc_skb() fails on the first iteration, a write to cp->rx_ring[-1] occurs. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/3c515.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/3c515.c b/drivers/net/3c515.c index 3e00fa8ea65f..4a7c32895be5 100644 --- a/drivers/net/3c515.c +++ b/drivers/net/3c515.c @@ -832,7 +832,9 @@ static int corkscrew_open(struct net_device *dev) skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */ vp->rx_ring[i].addr = isa_virt_to_bus(skb->data); } - vp->rx_ring[i - 1].next = isa_virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */ + if (i != 0) + vp->rx_ring[i - 1].next = + isa_virt_to_bus(&vp->rx_ring[0]); /* Wrap the ring. */ outl(isa_virt_to_bus(&vp->rx_ring[0]), ioaddr + UpListPtr); } if (vp->full_bus_master_tx) { /* Boomerang bus master Tx. */ -- cgit v1.2.3 From f0c5b35c6c93c89a9d8ccab19b0b4842f5dfddc5 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Wed, 29 Jul 2009 03:18:56 +0000 Subject: eexpress: Read buffer overflow start_code is 69 words, but the code always writes a multiple of 16 words, so the last 11 words written are outside the array. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/eexpress.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/eexpress.c b/drivers/net/eexpress.c index 1686dca28748..1f016d66684a 100644 --- a/drivers/net/eexpress.c +++ b/drivers/net/eexpress.c @@ -1474,13 +1474,13 @@ static void eexp_hw_init586(struct net_device *dev) outw(0x0000, ioaddr + 0x800c); outw(0x0000, ioaddr + 0x800e); - for (i = 0; i < (sizeof(start_code)); i+=32) { + for (i = 0; i < ARRAY_SIZE(start_code) * 2; i+=32) { int j; outw(i, ioaddr + SM_PTR); - for (j = 0; j < 16; j+=2) + for (j = 0; j < 16 && (i+j)/2 < ARRAY_SIZE(start_code); j+=2) outw(start_code[(i+j)/2], ioaddr+0x4000+j); - for (j = 0; j < 16; j+=2) + for (j = 0; j < 16 && (i+j+16)/2 < ARRAY_SIZE(start_code); j+=2) outw(start_code[(i+j+16)/2], ioaddr+0x8000+j); } -- cgit v1.2.3 From daed953721850381673687c59f3a0df553eb6626 Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Thu, 30 Jul 2009 17:16:05 -0400 Subject: hp-wmi: check that an input device exists in resume handler MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Some systems may not support input events, or registering the input handler may have failed. So check that an input device exists before trying to set the docking and tablet mode state during resume. Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13865 Reported-and-tested-by: Cédric Godin Signed-off-by: Frans Pop Acked-by: Matthew Garrett Signed-off-by: Len Brown --- drivers/platform/x86/hp-wmi.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/platform/x86/hp-wmi.c b/drivers/platform/x86/hp-wmi.c index ca508564a181..a2ad53e15874 100644 --- a/drivers/platform/x86/hp-wmi.c +++ b/drivers/platform/x86/hp-wmi.c @@ -520,11 +520,13 @@ static int hp_wmi_resume_handler(struct platform_device *device) * the input layer will only actually pass it on if the state * changed. */ - - input_report_switch(hp_wmi_input_dev, SW_DOCK, hp_wmi_dock_state()); - input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE, - hp_wmi_tablet_state()); - input_sync(hp_wmi_input_dev); + if (hp_wmi_input_dev) { + input_report_switch(hp_wmi_input_dev, SW_DOCK, + hp_wmi_dock_state()); + input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE, + hp_wmi_tablet_state()); + input_sync(hp_wmi_input_dev); + } return 0; } -- cgit v1.2.3 From 72fc939789dbe7ca091b50b686d45ac0df15417a Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 28 Jul 2009 23:43:08 +0000 Subject: pppoe: fix /proc/net/pppoe If a socket is hashed in last slot of pppoe hash table (PPPOE_HASH_SIZE-1) we report it many times (up to filling seq buffer) (Only the last socket of last slot) Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/pppoe.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/pppoe.c b/drivers/net/pppoe.c index f0031f1f97e5..5f2090233d7b 100644 --- a/drivers/net/pppoe.c +++ b/drivers/net/pppoe.c @@ -1063,6 +1063,7 @@ static void *pppoe_seq_next(struct seq_file *seq, void *v, loff_t *pos) else { int hash = hash_item(po->pppoe_pa.sid, po->pppoe_pa.remote); + po = NULL; while (++hash < PPPOE_HASH_SIZE) { po = pn->hash_table[hash]; if (po) -- cgit v1.2.3 From accff95c2500c7bce671c1f722de6f8810fe550d Mon Sep 17 00:00:00 2001 From: Jiajun Wu Date: Thu, 30 Jul 2009 14:20:42 -0700 Subject: gianfar: fix coalescing setup in ethtool support Parameter order for using mk_ic_value(count, time) was reversed, the patch fixes this. Signed-off-by: Jiajun Wu Signed-off-by: Li Yang Signed-off-by: David S. Miller --- drivers/net/gianfar_ethtool.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c index dbf06e9313cc..2234118eedbb 100644 --- a/drivers/net/gianfar_ethtool.c +++ b/drivers/net/gianfar_ethtool.c @@ -366,9 +366,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals return -EINVAL; } - priv->rxic = mk_ic_value( - gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs), - cvals->rx_max_coalesced_frames); + priv->rxic = mk_ic_value(cvals->rx_max_coalesced_frames, + gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs)); /* Set up tx coalescing */ if ((cvals->tx_coalesce_usecs == 0) || @@ -390,9 +389,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals return -EINVAL; } - priv->txic = mk_ic_value( - gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs), - cvals->tx_max_coalesced_frames); + priv->txic = mk_ic_value(cvals->tx_max_coalesced_frames, + gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs)); gfar_write(&priv->regs->rxic, 0); if (priv->rxcoalescing) -- cgit v1.2.3 From 8fe70a5f7167e02bbc18086970f0e92a5e55b80d Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Thu, 9 Jul 2009 16:28:33 +0800 Subject: ARM: S3C24XX: serial: Fix section mismatch warnings During kernel build process, the following warning was found: WARNING: drivers/serial/built-in.o(.data+0x304): Section mismatch in reference from the variable s3c2440_serial_drv to the function .devexit.text:s3c24xx_serial_remove() The variable s3c2440_serial_drv references the function __devexit s3c24xx_serial_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, The same warning happened for s3c241x platform. We rename variables to avoid these warnings. These changes also apply to s3c2400 & s3c24a0 for consistency. Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/s3c2400.c | 8 ++++---- drivers/serial/s3c2410.c | 8 ++++---- drivers/serial/s3c2412.c | 8 ++++---- drivers/serial/s3c2440.c | 8 ++++---- drivers/serial/s3c24a0.c | 8 ++++---- 5 files changed, 20 insertions(+), 20 deletions(-) (limited to 'drivers') diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c index fb00ed5296e6..fed1a9a1ffb4 100644 --- a/drivers/serial/s3c2400.c +++ b/drivers/serial/s3c2400.c @@ -76,7 +76,7 @@ static int s3c2400_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2400_uart_inf); } -static struct platform_driver s3c2400_serial_drv = { +static struct platform_driver s3c2400_serial_driver = { .probe = s3c2400_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -85,16 +85,16 @@ static struct platform_driver s3c2400_serial_drv = { }, }; -s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf); +s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf); static inline int s3c2400_serial_init(void) { - return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf); + return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf); } static inline void s3c2400_serial_exit(void) { - platform_driver_unregister(&s3c2400_serial_drv); + platform_driver_unregister(&s3c2400_serial_driver); } module_init(s3c2400_serial_init); diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c index b5d7cbcba2ae..c99f0821cae3 100644 --- a/drivers/serial/s3c2410.c +++ b/drivers/serial/s3c2410.c @@ -88,7 +88,7 @@ static int s3c2410_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2410_uart_inf); } -static struct platform_driver s3c2410_serial_drv = { +static struct platform_driver s3c2410_serial_driver = { .probe = s3c2410_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -97,16 +97,16 @@ static struct platform_driver s3c2410_serial_drv = { }, }; -s3c24xx_console_init(&s3c2410_serial_drv, &s3c2410_uart_inf); +s3c24xx_console_init(&s3c2410_serial_driver, &s3c2410_uart_inf); static int __init s3c2410_serial_init(void) { - return s3c24xx_serial_init(&s3c2410_serial_drv, &s3c2410_uart_inf); + return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf); } static void __exit s3c2410_serial_exit(void) { - platform_driver_unregister(&s3c2410_serial_drv); + platform_driver_unregister(&s3c2410_serial_driver); } module_init(s3c2410_serial_init); diff --git a/drivers/serial/s3c2412.c b/drivers/serial/s3c2412.c index 11dcb90bdfef..6e057d8809d3 100644 --- a/drivers/serial/s3c2412.c +++ b/drivers/serial/s3c2412.c @@ -121,7 +121,7 @@ static int s3c2412_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2412_uart_inf); } -static struct platform_driver s3c2412_serial_drv = { +static struct platform_driver s3c2412_serial_driver = { .probe = s3c2412_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -130,16 +130,16 @@ static struct platform_driver s3c2412_serial_drv = { }, }; -s3c24xx_console_init(&s3c2412_serial_drv, &s3c2412_uart_inf); +s3c24xx_console_init(&s3c2412_serial_driver, &s3c2412_uart_inf); static inline int s3c2412_serial_init(void) { - return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf); + return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf); } static inline void s3c2412_serial_exit(void) { - platform_driver_unregister(&s3c2412_serial_drv); + platform_driver_unregister(&s3c2412_serial_driver); } module_init(s3c2412_serial_init); diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c index 06c5b0cc47a3..69ff5d340f04 100644 --- a/drivers/serial/s3c2440.c +++ b/drivers/serial/s3c2440.c @@ -151,7 +151,7 @@ static int s3c2440_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c2440_uart_inf); } -static struct platform_driver s3c2440_serial_drv = { +static struct platform_driver s3c2440_serial_driver = { .probe = s3c2440_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -160,16 +160,16 @@ static struct platform_driver s3c2440_serial_drv = { }, }; -s3c24xx_console_init(&s3c2440_serial_drv, &s3c2440_uart_inf); +s3c24xx_console_init(&s3c2440_serial_driver, &s3c2440_uart_inf); static int __init s3c2440_serial_init(void) { - return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf); + return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf); } static void __exit s3c2440_serial_exit(void) { - platform_driver_unregister(&s3c2440_serial_drv); + platform_driver_unregister(&s3c2440_serial_driver); } module_init(s3c2440_serial_init); diff --git a/drivers/serial/s3c24a0.c b/drivers/serial/s3c24a0.c index 786a067d62ac..26c49e18bdd1 100644 --- a/drivers/serial/s3c24a0.c +++ b/drivers/serial/s3c24a0.c @@ -92,7 +92,7 @@ static int s3c24a0_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf); } -static struct platform_driver s3c24a0_serial_drv = { +static struct platform_driver s3c24a0_serial_driver = { .probe = s3c24a0_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -101,16 +101,16 @@ static struct platform_driver s3c24a0_serial_drv = { }, }; -s3c24xx_console_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf); +s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); static int __init s3c24a0_serial_init(void) { - return s3c24xx_serial_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf); + return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf); } static void __exit s3c24a0_serial_exit(void) { - platform_driver_unregister(&s3c24a0_serial_drv); + platform_driver_unregister(&s3c24a0_serial_driver); } module_init(s3c24a0_serial_init); -- cgit v1.2.3 From 909db80297ba65699a77d877f7bf618ba960f6fc Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Fri, 10 Jul 2009 19:30:56 +0800 Subject: ARM: S3C64XX: serial: Fix section mismatch warning Rename the structure to avoid the following warning: WARNING: vmlinux.o(.data+0x11ef4): Section mismatch in reference from the variable s3c6400_serial_drv to the function .devexit.text:s3c24xx_serial_remove() The variable s3c6400_serial_drv references the function __devexit s3c24xx_serial_remove() If the reference is valid then annotate the variable with __exit* (see linux/init.h) or name the variable: *driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/s3c6400.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/serial/s3c6400.c b/drivers/serial/s3c6400.c index 48f1a3781f0d..4be92ab50058 100644 --- a/drivers/serial/s3c6400.c +++ b/drivers/serial/s3c6400.c @@ -122,7 +122,7 @@ static int s3c6400_serial_probe(struct platform_device *dev) return s3c24xx_serial_probe(dev, &s3c6400_uart_inf); } -static struct platform_driver s3c6400_serial_drv = { +static struct platform_driver s3c6400_serial_driver = { .probe = s3c6400_serial_probe, .remove = __devexit_p(s3c24xx_serial_remove), .driver = { @@ -131,16 +131,16 @@ static struct platform_driver s3c6400_serial_drv = { }, }; -s3c24xx_console_init(&s3c6400_serial_drv, &s3c6400_uart_inf); +s3c24xx_console_init(&s3c6400_serial_driver, &s3c6400_uart_inf); static int __init s3c6400_serial_init(void) { - return s3c24xx_serial_init(&s3c6400_serial_drv, &s3c6400_uart_inf); + return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf); } static void __exit s3c6400_serial_exit(void) { - platform_driver_unregister(&s3c6400_serial_drv); + platform_driver_unregister(&s3c6400_serial_driver); } module_init(s3c6400_serial_init); -- cgit v1.2.3 From 8f9a71673d9f397a365f4d18c307e91141b8fe92 Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:25:09 +0000 Subject: ixgbe: Fix netpoll to be properly multiqueue aware Our ndo_poll_controller callback is broken for anything but non-multiqueue setups. This fixes that issue. Signed-off-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 13 ++++++++++--- 1 file changed, 10 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 200454f30f6a..60c4a8bf7d38 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -5360,12 +5360,19 @@ static int ixgbe_del_sanmac_netdev(struct net_device *dev) static void ixgbe_netpoll(struct net_device *netdev) { struct ixgbe_adapter *adapter = netdev_priv(netdev); + int i; - disable_irq(adapter->pdev->irq); adapter->flags |= IXGBE_FLAG_IN_NETPOLL; - ixgbe_intr(adapter->pdev->irq, netdev); + if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED) { + int num_q_vectors = adapter->num_msix_vectors - NON_Q_VECTORS; + for (i = 0; i < num_q_vectors; i++) { + struct ixgbe_q_vector *q_vector = adapter->q_vector[i]; + ixgbe_msix_clean_many(0, q_vector); + } + } else { + ixgbe_intr(adapter->pdev->irq, netdev); + } adapter->flags &= ~IXGBE_FLAG_IN_NETPOLL; - enable_irq(adapter->pdev->irq); } #endif -- cgit v1.2.3 From 0c19d6af9253f19b41821c29b9c49c2214f19425 Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:25:28 +0000 Subject: ixgbe: Fix usage of second flags bitmap when using LRO/RSC A second set of feature flag bits was added, and the hardware RSC engine flags were moved there. However, the code itself didn't make the move completely to use the new bitmap. Signed-off-by: Peter P Waskiewicz Jr Acked-by: Mallikarjuna R Chilakala Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_ethtool.c | 6 +++--- drivers/net/ixgbe/ixgbe_main.c | 12 ++++++------ 2 files changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 2a978008fd6e..7ddb50c03f0d 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1999,13 +1999,13 @@ static int ixgbe_set_flags(struct net_device *netdev, u32 data) ethtool_op_set_flags(netdev, data); - if (!(adapter->flags & IXGBE_FLAG2_RSC_CAPABLE)) + if (!(adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE)) return 0; /* if state changes we need to update adapter->flags and reset */ if ((!!(data & ETH_FLAG_LRO)) != - (!!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED))) { - adapter->flags ^= IXGBE_FLAG2_RSC_ENABLED; + (!!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED))) { + adapter->flags2 ^= IXGBE_FLAG2_RSC_ENABLED; if (netif_running(netdev)) ixgbe_reinit_locked(adapter); else diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 60c4a8bf7d38..110c65ab5cb5 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -780,7 +780,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, prefetch(next_rxd); cleaned_count++; - if (adapter->flags & IXGBE_FLAG2_RSC_CAPABLE) + if (adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE) rsc_count = ixgbe_get_rsc_count(rx_desc); if (rsc_count) { @@ -2036,7 +2036,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(0), psrtype); } } else { - if (!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED) && + if (!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) && (netdev->mtu <= ETH_DATA_LEN)) rx_buf_len = MAXIMUM_ETHERNET_VLAN_SIZE; else @@ -2165,7 +2165,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl); } - if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED) { + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) { /* Enable 82599 HW-RSC */ for (i = 0; i < adapter->num_rx_queues; i++) { j = adapter->rx_ring[i].reg_idx; @@ -3812,8 +3812,8 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82598; } else if (hw->mac.type == ixgbe_mac_82599EB) { adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82599; - adapter->flags |= IXGBE_FLAG2_RSC_CAPABLE; - adapter->flags |= IXGBE_FLAG2_RSC_ENABLED; + adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE; + adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED; adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE; adapter->ring_feature[RING_F_FDIR].indices = IXGBE_MAX_FDIR_INDICES; @@ -5618,7 +5618,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, if (pci_using_dac) netdev->features |= NETIF_F_HIGHDMA; - if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED) + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) netdev->features |= NETIF_F_LRO; /* make sure the EEPROM is good */ -- cgit v1.2.3 From 0a924578bc4a2823a95c151f56975c71f5c156bb Mon Sep 17 00:00:00 2001 From: Peter P Waskiewicz Jr Date: Thu, 30 Jul 2009 12:26:00 +0000 Subject: ixgbe: Fix RSC completion delay causing Rx interrupts to stop When a user disables interrupt throttling with ethtool on 82599 devices, the interrupt timer may not be re-enabled if hardware RSC is running. The RSC completions in hardware don't complete before the next ITR event tries to fire, so the ITR timer never gets re-armed. This patch increases the amount of time between interrupts when throttling is disabled (rx-usecs = 0) when the hardware RSC deature is enabled. Signed-off-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 2 ++ drivers/net/ixgbe/ixgbe_ethtool.c | 5 ++++- 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index 1b12c7ba275f..e11d83d5852b 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -96,6 +96,8 @@ #define IXGBE_TX_FLAGS_VLAN_PRIO_MASK 0x0000e000 #define IXGBE_TX_FLAGS_VLAN_SHIFT 16 +#define IXGBE_MAX_RSC_INT_RATE 162760 + /* wrapper around a pointer to a socket buffer, * so a DMA handle can be stored along with the buffer */ struct ixgbe_tx_buffer { diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 7ddb50c03f0d..79144e950a34 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1975,7 +1975,10 @@ static int ixgbe_set_coalesce(struct net_device *netdev, * any other value means disable eitr, which is best * served by setting the interrupt rate very high */ - adapter->eitr_param = IXGBE_MAX_INT_RATE; + if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) + adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE; + else + adapter->eitr_param = IXGBE_MAX_INT_RATE; adapter->itr_setting = 0; } -- cgit v1.2.3 From 95fc17aac45300f45968aacd97a536ddd8db8101 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Fri, 31 Jul 2009 12:39:15 +1000 Subject: md/raid6: release spare page at ->stop() Add missing call to safe_put_page from stop() by unifying open coded raid5_conf_t de-allocation under free_conf(). Cc: Signed-off-by: Dan Williams Signed-off-by: NeilBrown --- drivers/md/raid5.c | 26 ++++++++++++-------------- 1 file changed, 12 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 37835538b58e..39374230a463 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4316,6 +4316,15 @@ raid5_size(mddev_t *mddev, sector_t sectors, int raid_disks) return sectors * (raid_disks - conf->max_degraded); } +static void free_conf(raid5_conf_t *conf) +{ + shrink_stripes(conf); + safe_put_page(conf->spare_page); + kfree(conf->disks); + kfree(conf->stripe_hashtbl); + kfree(conf); +} + static raid5_conf_t *setup_conf(mddev_t *mddev) { raid5_conf_t *conf; @@ -4447,11 +4456,7 @@ static raid5_conf_t *setup_conf(mddev_t *mddev) abort: if (conf) { - shrink_stripes(conf); - safe_put_page(conf->spare_page); - kfree(conf->disks); - kfree(conf->stripe_hashtbl); - kfree(conf); + free_conf(conf); return ERR_PTR(-EIO); } else return ERR_PTR(-ENOMEM); @@ -4629,12 +4634,8 @@ abort: md_unregister_thread(mddev->thread); mddev->thread = NULL; if (conf) { - shrink_stripes(conf); print_raid5_conf(conf); - safe_put_page(conf->spare_page); - kfree(conf->disks); - kfree(conf->stripe_hashtbl); - kfree(conf); + free_conf(conf); } mddev->private = NULL; printk(KERN_ALERT "raid5: failed to run raid set %s\n", mdname(mddev)); @@ -4649,13 +4650,10 @@ static int stop(mddev_t *mddev) md_unregister_thread(mddev->thread); mddev->thread = NULL; - shrink_stripes(conf); - kfree(conf->stripe_hashtbl); mddev->queue->backing_dev_info.congested_fn = NULL; blk_sync_queue(mddev->queue); /* the unplug fn references 'conf'*/ sysfs_remove_group(&mddev->kobj, &raid5_attrs_group); - kfree(conf->disks); - kfree(conf); + free_conf(conf); mddev->private = NULL; return 0; } -- cgit v1.2.3 From da60a91d012bcb10bc5bcd86d585c4281742832c Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Thu, 18 Jun 2009 09:33:32 +0200 Subject: sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG so the page will be flushed on unmap on ARCH which need it. Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 62041c7e9246..fc96f8cb9c0b 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -773,8 +773,14 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) } if (!(host->flags & SDHCI_REQ_USE_DMA)) { - sg_miter_start(&host->sg_miter, - data->sg, data->sg_len, SG_MITER_ATOMIC); + int flags; + + flags = SG_MITER_ATOMIC; + if (host->data->flags & MMC_DATA_READ) + flags |= SG_MITER_TO_SG; + else + flags |= SG_MITER_FROM_SG; + sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); host->blocks = data->blocks; } -- cgit v1.2.3 From 4b2a108cd0d34880fe9d932258ca5b2ccebcd05e Mon Sep 17 00:00:00 2001 From: Sebastian Andrzej Siewior Date: Mon, 22 Jun 2009 09:18:05 +0200 Subject: cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit the code allready uses flush_kernel_dcache_page(). This patch updates the driver to the recent sg API changes which require that either SG_MITER_TO_SG or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page() in sg_mitter_stop() Signed-off-by: Sebastian Andrzej Siewior Acked-by: Michał Mirosław Signed-off-by: Pierre Ossman --- drivers/misc/cb710/sgbuf2.c | 4 ---- drivers/mmc/host/cb710-mmc.c | 6 +++--- include/linux/cb710.h | 29 +++-------------------------- 3 files changed, 6 insertions(+), 33 deletions(-) (limited to 'drivers') diff --git a/drivers/misc/cb710/sgbuf2.c b/drivers/misc/cb710/sgbuf2.c index d38a7acdb6ec..d019746551f3 100644 --- a/drivers/misc/cb710/sgbuf2.c +++ b/drivers/misc/cb710/sgbuf2.c @@ -114,7 +114,6 @@ static void sg_dwiter_write_slow(struct sg_mapping_iter *miter, uint32_t data) if (!left) return; addr += len; - flush_kernel_dcache_page(miter->page); } while (sg_dwiter_next(miter)); } @@ -142,9 +141,6 @@ void cb710_sg_dwiter_write_next_block(struct sg_mapping_iter *miter, uint32_t da return; } else sg_dwiter_write_slow(miter, data); - - if (miter->length == miter->consumed) - flush_kernel_dcache_page(miter->page); } EXPORT_SYMBOL_GPL(cb710_sg_dwiter_write_next_block); diff --git a/drivers/mmc/host/cb710-mmc.c b/drivers/mmc/host/cb710-mmc.c index 11efefb1af51..4e72964a7b43 100644 --- a/drivers/mmc/host/cb710-mmc.c +++ b/drivers/mmc/host/cb710-mmc.c @@ -278,7 +278,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data) if (unlikely(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8))) return -EINVAL; - sg_miter_start(&miter, data->sg, data->sg_len, 0); + sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_TO_SG); cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 15, CB710_MMC_C2_READ_PIO_SIZE_MASK); @@ -307,7 +307,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data) goto out; } out: - cb710_sg_miter_stop_writing(&miter); + sg_miter_stop(&miter); return err; } @@ -322,7 +322,7 @@ static int cb710_mmc_send(struct cb710_slot *slot, struct mmc_data *data) if (unlikely(data->blocks > 1 && data->blksz & 15)) return -EINVAL; - sg_miter_start(&miter, data->sg, data->sg_len, 0); + sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_FROM_SG); cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 0, CB710_MMC_C2_READ_PIO_SIZE_MASK); diff --git a/include/linux/cb710.h b/include/linux/cb710.h index 63bc9a4d2926..8cc10411bab2 100644 --- a/include/linux/cb710.h +++ b/include/linux/cb710.h @@ -140,29 +140,6 @@ void cb710_dump_regs(struct cb710_chip *chip, unsigned dump); #include #include -/** - * cb710_sg_miter_stop_writing - stop mapping iteration after writing - * @miter: sg mapping iter to be stopped - * - * Description: - * Stops mapping iterator @miter. @miter should have been started - * started using sg_miter_start(). A stopped iteration can be - * resumed by calling sg_miter_next() on it. This is useful when - * resources (kmap) need to be released during iteration. - * - * This is a convenience wrapper that will be optimized out for arches - * that don't need flush_kernel_dcache_page(). - * - * Context: - * IRQ disabled if the SG_MITER_ATOMIC is set. Don't care otherwise. - */ -static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter) -{ - if (miter->page) - flush_kernel_dcache_page(miter->page); - sg_miter_stop(miter); -} - /* * 32-bit PIO mapping sg iterator * @@ -171,12 +148,12 @@ static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter) * without DMA support). * * Best-case reading (transfer from device): - * sg_miter_start(); + * sg_miter_start(, SG_MITER_TO_SG); * cb710_sg_dwiter_write_from_io(); - * cb710_sg_miter_stop_writing(); + * sg_miter_stop(); * * Best-case writing (transfer to device): - * sg_miter_start(); + * sg_miter_start(, SG_MITER_FROM_SG); * cb710_sg_dwiter_read_to_io(); * sg_miter_stop(); */ -- cgit v1.2.3 From a9239d750d9991f2feee78fc5669a4613abc1adb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Sun, 28 Jun 2009 09:26:31 -0700 Subject: imxmmc: Remove unnecessary semicolons Signed-off-by: Joe Perches Acked-by: Pavel Pisa Signed-off-by: Pierre Ossman --- drivers/mmc/host/imxmmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c index e0be21a4a696..bf98d7cc928a 100644 --- a/drivers/mmc/host/imxmmc.c +++ b/drivers/mmc/host/imxmmc.c @@ -652,7 +652,7 @@ static irqreturn_t imxmci_irq(int irq, void *devid) set_bit(IMXMCI_PEND_STARTED_b, &host->pending_events); tasklet_schedule(&host->tasklet); - return IRQ_RETVAL(handled);; + return IRQ_RETVAL(handled); } static void imxmci_tasklet_fnc(unsigned long data) -- cgit v1.2.3 From 550e7fd8afb7664ae7cedb398c407694e2bf7d3c Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:17 -0300 Subject: thinkpad-acpi: disable broken bay and dock subdrivers Currently, the ThinkPad-ACPI bay and dock drivers are completely broken, and cause a NULL pointer derreference in kernel mode (and, therefore, an OOPS) when they try to issue events (i.e. on dock, undock, bay ejection, etc). OTOH, the standard ACPI dock driver can handle the hotplug bays and docks of the ThinkPads just fine (including batteries) as of 2.6.27. In fact, it does a much better job of it than thinkpad-acpi ever did. It is just not worth the hassle to find a way to fix this crap without breaking the (deprecated) thinkpad-acpi dock/bay ABI. This is old, deprecated code that sees little testing or use. As a quick fix suitable for -stable backports, mark the thinkpad-acpi bay and dock subdrivers as BROKEN in Kconfig. The dead code will be removed by a later patch. This fixes bugzilla #13669, and should be applied to 2.6.27 and later. Signed-off-by: Henrique de Moraes Holschuh Reported-by: Joerg Platte Cc: stable@kernel.org Signed-off-by: Len Brown --- drivers/platform/x86/Kconfig | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 46dad12f952f..6335f63892dc 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -281,6 +281,7 @@ config THINKPAD_ACPI_DOCK bool "Legacy Docking Station Support" depends on THINKPAD_ACPI depends on ACPI_DOCK=n + depends on BROKEN default n ---help--- Allows the thinkpad_acpi driver to handle docking station events. @@ -294,7 +295,8 @@ config THINKPAD_ACPI_DOCK config THINKPAD_ACPI_BAY bool "Legacy Removable Bay Support" depends on THINKPAD_ACPI - default y + depends on BROKEN + default n ---help--- Allows the thinkpad_acpi driver to handle removable bays. It will electrically disable the device in the bay, and also generate -- cgit v1.2.3 From 1f6fc2de9525e34ee93bd392fa046369a8cfbf1e Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:18 -0300 Subject: thinkpad-acpi: remove dock and bay subdrivers The standard ACPI dock driver can handle the hotplug bays and docks of the ThinkPads just fine (including batteries) as of 2.6.27, and the code in thinkpad-acpi for the dock and bay subdrivers is currently broken anyway... Userspace needs some love to support the two-stage ejection nicely, but it is simple enough to do through udev rules (you don't even need HAL) so this wouldn't justify fixing the dock and bay subdrivers, either. That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well as support for the weird dock of the model 570, but since such support has never left the "experimental" stage, it is also not a strong enough reason to find a way to fix this code. Users of ThinkPads with warm-swap bays are urged to request that _EJ3 support be added to the regular ACPI dock driver, if such feature is indeed useful for them. Signed-off-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- Documentation/laptops/thinkpad-acpi.txt | 127 ------------- drivers/platform/x86/Kconfig | 27 --- drivers/platform/x86/thinkpad_acpi.c | 327 -------------------------------- 3 files changed, 481 deletions(-) (limited to 'drivers') diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index f2296ecedb89..e2ddcdeb61b6 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -36,8 +36,6 @@ detailed description): - Bluetooth enable and disable - video output switching, expansion control - ThinkLight on and off - - limited docking and undocking - - UltraBay eject - CMOS/UCMS control - LED control - ACPI sounds @@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off". It is impossible to know if the status returned through sysfs is valid. -Docking / undocking -- /proc/acpi/ibm/dock ------------------------------------------- - -Docking and undocking (e.g. with the X4 UltraBase) requires some -actions to be taken by the operating system to safely make or break -the electrical connections with the dock. - -The docking feature of this driver generates the following ACPI events: - - ibm/dock GDCK 00000003 00000001 -- eject request - ibm/dock GDCK 00000003 00000002 -- undocked - ibm/dock GDCK 00000000 00000003 -- docked - -NOTE: These events will only be generated if the laptop was docked -when originally booted. This is due to the current lack of support for -hot plugging of devices in the Linux ACPI framework. If the laptop was -booted while not in the dock, the following message is shown in the -logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present - -In this case, no dock-related events are generated but the dock and -undock commands described below still work. They can be executed -manually or triggered by Fn key combinations (see the example acpid -configuration files included in the driver tarball package available -on the web site). - -When the eject request button on the dock is pressed, the first event -above is generated. The handler for this event should issue the -following command: - - echo undock > /proc/acpi/ibm/dock - -After the LED on the dock goes off, it is safe to eject the laptop. -Note: if you pressed this key by mistake, go ahead and eject the -laptop, then dock it back in. Otherwise, the dock may not function as -expected. - -When the laptop is docked, the third event above is generated. The -handler for this event should issue the following command to fully -enable the dock: - - echo dock > /proc/acpi/ibm/dock - -The contents of the /proc/acpi/ibm/dock file shows the current status -of the dock, as provided by the ACPI framework. - -The docking support in this driver does not take care of enabling or -disabling any other devices you may have attached to the dock. For -example, a CD drive plugged into the UltraBase needs to be disabled or -enabled separately. See the provided example acpid configuration files -for how this can be accomplished. - -There is no support yet for PCI devices that may be attached to a -docking station, e.g. in the ThinkPad Dock II. The driver currently -does not recognize, enable or disable such devices. This means that -the only docking stations currently supported are the X-series -UltraBase docks and "dumb" port replicators like the Mini Dock (the -latter don't need any ACPI support, actually). - - -UltraBay eject -- /proc/acpi/ibm/bay ------------------------------------- - -Inserting or ejecting an UltraBay device requires some actions to be -taken by the operating system to safely make or break the electrical -connections with the device. - -This feature generates the following ACPI events: - - ibm/bay MSTR 00000003 00000000 -- eject request - ibm/bay MSTR 00000001 00000000 -- eject lever inserted - -NOTE: These events will only be generated if the UltraBay was present -when the laptop was originally booted (on the X series, the UltraBay -is in the dock, so it may not be present if the laptop was undocked). -This is due to the current lack of support for hot plugging of devices -in the Linux ACPI framework. If the laptop was booted without the -UltraBay, the following message is shown in the logs: - - Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present - -In this case, no bay-related events are generated but the eject -command described below still works. It can be executed manually or -triggered by a hot key combination. - -Sliding the eject lever generates the first event shown above. The -handler for this event should take whatever actions are necessary to -shut down the device in the UltraBay (e.g. call idectl), then issue -the following command: - - echo eject > /proc/acpi/ibm/bay - -After the LED on the UltraBay goes off, it is safe to pull out the -device. - -When the eject lever is inserted, the second event above is -generated. The handler for this event should take whatever actions are -necessary to enable the UltraBay device (e.g. call idectl). - -The contents of the /proc/acpi/ibm/bay file shows the current status -of the UltraBay, as provided by the ACPI framework. - -EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use -this feature, you need to supply the experimental=1 parameter when -loading the module): - -These models do not have a button near the UltraBay device to request -a hot eject but rather require the laptop to be put to sleep -(suspend-to-ram) before the bay device is ejected or inserted). -The sequence of steps to eject the device is as follows: - - echo eject > /proc/acpi/ibm/bay - put the ThinkPad to sleep - remove the drive - resume from sleep - cat /proc/acpi/ibm/bay should show that the drive was removed - -On the A3x, both the UltraBay 2000 and UltraBay Plus devices are -supported. Use "eject2" instead of "eject" for the second bay. - -Note: the UltraBay eject support on the 600e/x, A22p and A3x is -EXPERIMENTAL and may not work as expected. USE WITH CAUTION! - - CMOS/UCMS control ----------------- diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig index 6335f63892dc..77c6097ced80 100644 --- a/drivers/platform/x86/Kconfig +++ b/drivers/platform/x86/Kconfig @@ -277,33 +277,6 @@ config THINKPAD_ACPI_UNSAFE_LEDS Say N here, unless you are building a kernel for your own use, and need to control the important firmware LEDs. -config THINKPAD_ACPI_DOCK - bool "Legacy Docking Station Support" - depends on THINKPAD_ACPI - depends on ACPI_DOCK=n - depends on BROKEN - default n - ---help--- - Allows the thinkpad_acpi driver to handle docking station events. - This support was made obsolete by the generic ACPI docking station - support (CONFIG_ACPI_DOCK). It will allow locking and removing the - laptop from the docking station, but will not properly connect PCI - devices. - - If you are not sure, say N here. - -config THINKPAD_ACPI_BAY - bool "Legacy Removable Bay Support" - depends on THINKPAD_ACPI - depends on BROKEN - default n - ---help--- - Allows the thinkpad_acpi driver to handle removable bays. It will - electrically disable the device in the bay, and also generate - notifications when the bay lever is ejected or inserted. - - If you are not sure, say Y here. - config THINKPAD_ACPI_VIDEO bool "Video output control support" depends on THINKPAD_ACPI diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index a463fd72c495..27d68e719e90 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -239,12 +239,6 @@ struct ibm_init_struct { }; static struct { -#ifdef CONFIG_THINKPAD_ACPI_BAY - u32 bay_status:1; - u32 bay_eject:1; - u32 bay_status2:1; - u32 bay_eject2:1; -#endif u32 bluetooth:1; u32 hotkey:1; u32 hotkey_mask:1; @@ -589,18 +583,6 @@ static int acpi_ec_write(int i, u8 v) return 1; } -#if defined(CONFIG_THINKPAD_ACPI_DOCK) || defined(CONFIG_THINKPAD_ACPI_BAY) -static int _sta(acpi_handle handle) -{ - int status; - - if (!handle || !acpi_evalf(handle, &status, "_STA", "d")) - status = 0; - - return status; -} -#endif - static int issue_thinkpad_cmos_command(int cmos_cmd) { if (!cmos_handle) @@ -4441,293 +4423,6 @@ static struct ibm_struct light_driver_data = { .exit = light_exit, }; -/************************************************************************* - * Dock subdriver - */ - -#ifdef CONFIG_THINKPAD_ACPI_DOCK - -static void dock_notify(struct ibm_struct *ibm, u32 event); -static int dock_read(char *p); -static int dock_write(char *buf); - -TPACPI_HANDLE(dock, root, "\\_SB.GDCK", /* X30, X31, X40 */ - "\\_SB.PCI0.DOCK", /* 600e/x,770e,770x,A2xm/p,T20-22,X20-21 */ - "\\_SB.PCI0.PCI1.DOCK", /* all others */ - "\\_SB.PCI.ISA.SLCE", /* 570 */ - ); /* A21e,G4x,R30,R31,R32,R40,R40e,R50e */ - -/* don't list other alternatives as we install a notify handler on the 570 */ -TPACPI_HANDLE(pci, root, "\\_SB.PCI"); /* 570 */ - -static const struct acpi_device_id ibm_pci_device_ids[] = { - {PCI_ROOT_HID_STRING, 0}, - {"", 0}, -}; - -static struct tp_acpi_drv_struct ibm_dock_acpidriver[2] = { - { - .notify = dock_notify, - .handle = &dock_handle, - .type = ACPI_SYSTEM_NOTIFY, - }, - { - /* THIS ONE MUST NEVER BE USED FOR DRIVER AUTOLOADING. - * We just use it to get notifications of dock hotplug - * in very old thinkpads */ - .hid = ibm_pci_device_ids, - .notify = dock_notify, - .handle = &pci_handle, - .type = ACPI_SYSTEM_NOTIFY, - }, -}; - -static struct ibm_struct dock_driver_data[2] = { - { - .name = "dock", - .read = dock_read, - .write = dock_write, - .acpi = &ibm_dock_acpidriver[0], - }, - { - .name = "dock", - .acpi = &ibm_dock_acpidriver[1], - }, -}; - -#define dock_docked() (_sta(dock_handle) & 1) - -static int __init dock_init(struct ibm_init_struct *iibm) -{ - vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver\n"); - - TPACPI_ACPIHANDLE_INIT(dock); - - vdbg_printk(TPACPI_DBG_INIT, "dock is %s\n", - str_supported(dock_handle != NULL)); - - return (dock_handle)? 0 : 1; -} - -static int __init dock_init2(struct ibm_init_struct *iibm) -{ - int dock2_needed; - - vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver part 2\n"); - - if (dock_driver_data[0].flags.acpi_driver_registered && - dock_driver_data[0].flags.acpi_notify_installed) { - TPACPI_ACPIHANDLE_INIT(pci); - dock2_needed = (pci_handle != NULL); - vdbg_printk(TPACPI_DBG_INIT, - "dock PCI handler for the TP 570 is %s\n", - str_supported(dock2_needed)); - } else { - vdbg_printk(TPACPI_DBG_INIT, - "dock subdriver part 2 not required\n"); - dock2_needed = 0; - } - - return (dock2_needed)? 0 : 1; -} - -static void dock_notify(struct ibm_struct *ibm, u32 event) -{ - int docked = dock_docked(); - int pci = ibm->acpi->hid && ibm->acpi->device && - acpi_match_device_ids(ibm->acpi->device, ibm_pci_device_ids); - int data; - - if (event == 1 && !pci) /* 570 */ - data = 1; /* button */ - else if (event == 1 && pci) /* 570 */ - data = 3; /* dock */ - else if (event == 3 && docked) - data = 1; /* button */ - else if (event == 3 && !docked) - data = 2; /* undock */ - else if (event == 0 && docked) - data = 3; /* dock */ - else { - printk(TPACPI_ERR "unknown dock event %d, status %d\n", - event, _sta(dock_handle)); - data = 0; /* unknown */ - } - acpi_bus_generate_proc_event(ibm->acpi->device, event, data); - acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class, - dev_name(&ibm->acpi->device->dev), - event, data); -} - -static int dock_read(char *p) -{ - int len = 0; - int docked = dock_docked(); - - if (!dock_handle) - len += sprintf(p + len, "status:\t\tnot supported\n"); - else if (!docked) - len += sprintf(p + len, "status:\t\tundocked\n"); - else { - len += sprintf(p + len, "status:\t\tdocked\n"); - len += sprintf(p + len, "commands:\tdock, undock\n"); - } - - return len; -} - -static int dock_write(char *buf) -{ - char *cmd; - - if (!dock_docked()) - return -ENODEV; - - while ((cmd = next_cmd(&buf))) { - if (strlencmp(cmd, "undock") == 0) { - if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 0) || - !acpi_evalf(dock_handle, NULL, "_EJ0", "vd", 1)) - return -EIO; - } else if (strlencmp(cmd, "dock") == 0) { - if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 1)) - return -EIO; - } else - return -EINVAL; - } - - return 0; -} - -#endif /* CONFIG_THINKPAD_ACPI_DOCK */ - -/************************************************************************* - * Bay subdriver - */ - -#ifdef CONFIG_THINKPAD_ACPI_BAY - -TPACPI_HANDLE(bay, root, "\\_SB.PCI.IDE.SECN.MAST", /* 570 */ - "\\_SB.PCI0.IDE0.IDES.IDSM", /* 600e/x, 770e, 770x */ - "\\_SB.PCI0.SATA.SCND.MSTR", /* T60, X60, Z60 */ - "\\_SB.PCI0.IDE0.SCND.MSTR", /* all others */ - ); /* A21e, R30, R31 */ -TPACPI_HANDLE(bay_ej, bay, "_EJ3", /* 600e/x, A2xm/p, A3x */ - "_EJ0", /* all others */ - ); /* 570,A21e,G4x,R30,R31,R32,R40e,R50e */ -TPACPI_HANDLE(bay2, root, "\\_SB.PCI0.IDE0.PRIM.SLAV", /* A3x, R32 */ - "\\_SB.PCI0.IDE0.IDEP.IDPS", /* 600e/x, 770e, 770x */ - ); /* all others */ -TPACPI_HANDLE(bay2_ej, bay2, "_EJ3", /* 600e/x, 770e, A3x */ - "_EJ0", /* 770x */ - ); /* all others */ - -static int __init bay_init(struct ibm_init_struct *iibm) -{ - vdbg_printk(TPACPI_DBG_INIT, "initializing bay subdriver\n"); - - TPACPI_ACPIHANDLE_INIT(bay); - if (bay_handle) - TPACPI_ACPIHANDLE_INIT(bay_ej); - TPACPI_ACPIHANDLE_INIT(bay2); - if (bay2_handle) - TPACPI_ACPIHANDLE_INIT(bay2_ej); - - tp_features.bay_status = bay_handle && - acpi_evalf(bay_handle, NULL, "_STA", "qv"); - tp_features.bay_status2 = bay2_handle && - acpi_evalf(bay2_handle, NULL, "_STA", "qv"); - - tp_features.bay_eject = bay_handle && bay_ej_handle && - (strlencmp(bay_ej_path, "_EJ0") == 0 || experimental); - tp_features.bay_eject2 = bay2_handle && bay2_ej_handle && - (strlencmp(bay2_ej_path, "_EJ0") == 0 || experimental); - - vdbg_printk(TPACPI_DBG_INIT, - "bay 1: status %s, eject %s; bay 2: status %s, eject %s\n", - str_supported(tp_features.bay_status), - str_supported(tp_features.bay_eject), - str_supported(tp_features.bay_status2), - str_supported(tp_features.bay_eject2)); - - return (tp_features.bay_status || tp_features.bay_eject || - tp_features.bay_status2 || tp_features.bay_eject2)? 0 : 1; -} - -static void bay_notify(struct ibm_struct *ibm, u32 event) -{ - acpi_bus_generate_proc_event(ibm->acpi->device, event, 0); - acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class, - dev_name(&ibm->acpi->device->dev), - event, 0); -} - -#define bay_occupied(b) (_sta(b##_handle) & 1) - -static int bay_read(char *p) -{ - int len = 0; - int occupied = bay_occupied(bay); - int occupied2 = bay_occupied(bay2); - int eject, eject2; - - len += sprintf(p + len, "status:\t\t%s\n", - tp_features.bay_status ? - (occupied ? "occupied" : "unoccupied") : - "not supported"); - if (tp_features.bay_status2) - len += sprintf(p + len, "status2:\t%s\n", occupied2 ? - "occupied" : "unoccupied"); - - eject = tp_features.bay_eject && occupied; - eject2 = tp_features.bay_eject2 && occupied2; - - if (eject && eject2) - len += sprintf(p + len, "commands:\teject, eject2\n"); - else if (eject) - len += sprintf(p + len, "commands:\teject\n"); - else if (eject2) - len += sprintf(p + len, "commands:\teject2\n"); - - return len; -} - -static int bay_write(char *buf) -{ - char *cmd; - - if (!tp_features.bay_eject && !tp_features.bay_eject2) - return -ENODEV; - - while ((cmd = next_cmd(&buf))) { - if (tp_features.bay_eject && strlencmp(cmd, "eject") == 0) { - if (!acpi_evalf(bay_ej_handle, NULL, NULL, "vd", 1)) - return -EIO; - } else if (tp_features.bay_eject2 && - strlencmp(cmd, "eject2") == 0) { - if (!acpi_evalf(bay2_ej_handle, NULL, NULL, "vd", 1)) - return -EIO; - } else - return -EINVAL; - } - - return 0; -} - -static struct tp_acpi_drv_struct ibm_bay_acpidriver = { - .notify = bay_notify, - .handle = &bay_handle, - .type = ACPI_SYSTEM_NOTIFY, -}; - -static struct ibm_struct bay_driver_data = { - .name = "bay", - .read = bay_read, - .write = bay_write, - .acpi = &ibm_bay_acpidriver, -}; - -#endif /* CONFIG_THINKPAD_ACPI_BAY */ - /************************************************************************* * CMOS subdriver */ @@ -7854,22 +7549,6 @@ static struct ibm_init_struct ibms_init[] __initdata = { .init = light_init, .data = &light_driver_data, }, -#ifdef CONFIG_THINKPAD_ACPI_DOCK - { - .init = dock_init, - .data = &dock_driver_data[0], - }, - { - .init = dock_init2, - .data = &dock_driver_data[1], - }, -#endif -#ifdef CONFIG_THINKPAD_ACPI_BAY - { - .init = bay_init, - .data = &bay_driver_data, - }, -#endif { .init = cmos_init, .data = &cmos_driver_data, @@ -7968,12 +7647,6 @@ TPACPI_PARAM(hotkey); TPACPI_PARAM(bluetooth); TPACPI_PARAM(video); TPACPI_PARAM(light); -#ifdef CONFIG_THINKPAD_ACPI_DOCK -TPACPI_PARAM(dock); -#endif -#ifdef CONFIG_THINKPAD_ACPI_BAY -TPACPI_PARAM(bay); -#endif /* CONFIG_THINKPAD_ACPI_BAY */ TPACPI_PARAM(cmos); TPACPI_PARAM(led); TPACPI_PARAM(beep); -- cgit v1.2.3 From 5b05d4696d38c3172e79e855cc1e2ed044589508 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Sat, 1 Aug 2009 12:04:19 -0300 Subject: thinkpad-acpi: restrict procfs count value to sane upper limit Signed-off-by: Michael Buesch Acked-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- drivers/platform/x86/thinkpad_acpi.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 27d68e719e90..18f9ee63c50a 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -766,6 +766,8 @@ static int dispatch_procfs_write(struct file *file, if (!ibm || !ibm->write) return -EINVAL; + if (count > PAGE_SIZE - 2) + return -EINVAL; kernbuf = kmalloc(count + 2, GFP_KERNEL); if (!kernbuf) -- cgit v1.2.3 From 59fe4fe34d7afdf63208124f313be9056feaa2f4 Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 1 Aug 2009 12:04:20 -0300 Subject: thinkpad-acpi: fix incorrect use of TPACPI_BRGHT_MODE_ECNVRAM HBRV-based default selection of backlight control strategy didn't work well, at least the X41 defines it but doesn't use it and I don't think it will stop there. Switch to a white/blacklist. All models that have HBRV defined have been included in the list, and initially all ATI GPUs will get ECNVRAM, and the Intel GPUs will get UCMS_STEP. Symptoms of incorrect backlight mode selection are: 1. Non-working backlight control through sysfs; 2. Backlight gets reset to the lowest level at every shutdown, reboot and when thinkpad-acpi gets unloaded; This fixes a regression in 2.6.30, bugzilla #13826 Signed-off-by: Henrique de Moraes Holschuh Reported-by: Tobias Diedrich Cc: stable@kernel.org Signed-off-by: Len Brown --- drivers/platform/x86/thinkpad_acpi.c | 61 +++++++++++++++++++++++++++--------- 1 file changed, 47 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 18f9ee63c50a..e85600852502 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -5642,14 +5642,48 @@ static struct backlight_ops ibm_backlight_data = { /* --------------------------------------------------------------------- */ +/* + * These are only useful for models that have only one possibility + * of GPU. If the BIOS model handles both ATI and Intel, don't use + * these quirks. + */ +#define TPACPI_BRGHT_Q_NOEC 0x0001 /* Must NOT use EC HBRV */ +#define TPACPI_BRGHT_Q_EC 0x0002 /* Should or must use EC HBRV */ +#define TPACPI_BRGHT_Q_ASK 0x8000 /* Ask for user report */ + +static const struct tpacpi_quirk brightness_quirk_table[] __initconst = { + /* Models with ATI GPUs known to require ECNVRAM mode */ + TPACPI_Q_IBM('1', 'Y', TPACPI_BRGHT_Q_EC), /* T43/p ATI */ + + /* Models with ATI GPUs (waiting confirmation) */ + TPACPI_Q_IBM('1', 'R', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('1', 'Q', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('7', '6', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + TPACPI_Q_IBM('7', '8', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC), + + /* Models with Intel Extreme Graphics 2 (waiting confirmation) */ + TPACPI_Q_IBM('1', 'V', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + TPACPI_Q_IBM('1', 'W', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + TPACPI_Q_IBM('1', 'U', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC), + + /* Models with Intel GMA900 */ + TPACPI_Q_IBM('7', '0', TPACPI_BRGHT_Q_NOEC), /* T43, R52 */ + TPACPI_Q_IBM('7', '4', TPACPI_BRGHT_Q_NOEC), /* X41 */ + TPACPI_Q_IBM('7', '5', TPACPI_BRGHT_Q_NOEC), /* X41 Tablet */ +}; + static int __init brightness_init(struct ibm_init_struct *iibm) { int b; + unsigned long quirks; vdbg_printk(TPACPI_DBG_INIT, "initializing brightness subdriver\n"); mutex_init(&brightness_mutex); + quirks = tpacpi_check_quirks(brightness_quirk_table, + ARRAY_SIZE(brightness_quirk_table)); + /* * We always attempt to detect acpi support, so as to switch * Lenovo Vista BIOS to ACPI brightness mode even if we are not @@ -5706,23 +5740,13 @@ static int __init brightness_init(struct ibm_init_struct *iibm) /* TPACPI_BRGHT_MODE_AUTO not implemented yet, just use default */ if (brightness_mode == TPACPI_BRGHT_MODE_AUTO || brightness_mode == TPACPI_BRGHT_MODE_MAX) { - if (thinkpad_id.vendor == PCI_VENDOR_ID_IBM) { - /* - * IBM models that define HBRV probably have - * EC-based backlight level control - */ - if (acpi_evalf(ec_handle, NULL, "HBRV", "qd")) - /* T40-T43, R50-R52, R50e, R51e, X31-X41 */ - brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM; - else - /* all other IBM ThinkPads */ - brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP; - } else - /* All Lenovo ThinkPads */ + if (quirks & TPACPI_BRGHT_Q_EC) + brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM; + else brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP; dbg_printk(TPACPI_DBG_BRGHT, - "selected brightness_mode=%d\n", + "driver auto-selected brightness_mode=%d\n", brightness_mode); } @@ -5749,6 +5773,15 @@ static int __init brightness_init(struct ibm_init_struct *iibm) vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_BRGHT, "brightness is supported\n"); + if (quirks & TPACPI_BRGHT_Q_ASK) { + printk(TPACPI_NOTICE + "brightness: will use unverified default: " + "brightness_mode=%d\n", brightness_mode); + printk(TPACPI_NOTICE + "brightness: please report to %s whether it works well " + "or not on your ThinkPad\n", TPACPI_MAIL); + } + ibm_backlight_device->props.max_brightness = (tp_features.bright_16levels)? 15 : 7; ibm_backlight_device->props.brightness = b & TP_EC_BACKLIGHT_LVLMSK; -- cgit v1.2.3 From 447c233da4d109c6194fefd69e5185cbc93cc062 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 08:02:28 +0000 Subject: parisc: Fix read buffer overflow in pdc_stable driver Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: Helge Deller --- drivers/parisc/pdc_stable.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/parisc/pdc_stable.c b/drivers/parisc/pdc_stable.c index f9f9a5f1bbd0..13a64bc081b6 100644 --- a/drivers/parisc/pdc_stable.c +++ b/drivers/parisc/pdc_stable.c @@ -370,7 +370,7 @@ pdcspath_layer_read(struct pdcspath_entry *entry, char *buf) if (!i) /* entry is not ready */ return -ENODATA; - for (i = 0; devpath->layers[i] && (likely(i < 6)); i++) + for (i = 0; i < 6 && devpath->layers[i]; i++) out += sprintf(out, "%u ", devpath->layers[i]); out += sprintf(out, "\n"); -- cgit v1.2.3 From 450d6e306b4717bfae11218a02648509baf04ce1 Mon Sep 17 00:00:00 2001 From: Stoyan Gaydarov Date: Thu, 30 Jul 2009 10:25:19 +0000 Subject: parisc: fixed faulty check in lba_pci This patche fixes a spelling error that has resulted from copy and pasting. The location of the error was found using a semantic patch but the semantic patch was not trying to find these errors. After looking things over it seemed logical that this change was needed. Signed-off-by: Stoyan Gaydarov Signed-off-by: Helge Deller --- drivers/parisc/lba_pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/parisc/lba_pci.c b/drivers/parisc/lba_pci.c index ede614616f8e..3aeb3279c92a 100644 --- a/drivers/parisc/lba_pci.c +++ b/drivers/parisc/lba_pci.c @@ -992,7 +992,7 @@ lba_pat_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev) return; io_pdc_cell = kzalloc(sizeof(pdc_pat_cell_mod_maddr_block_t), GFP_KERNEL); - if (!pa_pdc_cell) { + if (!io_pdc_cell) { kfree(pa_pdc_cell); return; } -- cgit v1.2.3 From 6b4dbcd86a9d464057fcc7abe4d0574093071fcc Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Mon, 20 Jul 2009 22:58:44 +0000 Subject: parisc: isa-eeprom - Fix loff_t usage loff_t is a signed type. If userspace passes a negative ppos, the "count" range check is weakened. "count"s bigger than HPEE_MAX_LENGTH will pass the check. Also, if ppos is negative, the readb(eisa_eeprom_addr + *ppos) will poke in random memory. Signed-off-by: Michael Buesch Cc: stable@kernel.org Signed-off-by: Helge Deller --- drivers/parisc/eisa_eeprom.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/parisc/eisa_eeprom.c b/drivers/parisc/eisa_eeprom.c index 685d94e69d44..8c0b26e9b98a 100644 --- a/drivers/parisc/eisa_eeprom.c +++ b/drivers/parisc/eisa_eeprom.c @@ -55,7 +55,7 @@ static ssize_t eisa_eeprom_read(struct file * file, ssize_t ret; int i; - if (*ppos >= HPEE_MAX_LENGTH) + if (*ppos < 0 || *ppos >= HPEE_MAX_LENGTH) return 0; count = *ppos + count < HPEE_MAX_LENGTH ? count : HPEE_MAX_LENGTH - *ppos; -- cgit v1.2.3 From b10ff54f9f58adfb708b53e6e56ed3d7804ade74 Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 15:27:20 +0000 Subject: parisc: includecheck fix for ccio-dma.c fix the following 'make includecheck' warning: drivers/parisc/ccio-dma.c: linux/proc_fs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Signed-off-by: Helge Deller --- drivers/parisc/ccio-dma.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/parisc/ccio-dma.c b/drivers/parisc/ccio-dma.c index 0f0e0b919ef4..a45b0c0d574e 100644 --- a/drivers/parisc/ccio-dma.c +++ b/drivers/parisc/ccio-dma.c @@ -70,7 +70,6 @@ #undef CCIO_COLLECT_STATS #endif -#include #include /* for proc_runway_root */ #ifdef DEBUG_CCIO_INIT -- cgit v1.2.3 From c6fe6b0783a8fd923d11dd0388cbd561ff15bdf1 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:13:29 +0200 Subject: parisc: hp_sdc_mlc.c - check return value of down_trylock() Signed-off-by: Helge Deller --- drivers/input/serio/hp_sdc_mlc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/input/serio/hp_sdc_mlc.c b/drivers/input/serio/hp_sdc_mlc.c index b587e2d576ac..820e51673b26 100644 --- a/drivers/input/serio/hp_sdc_mlc.c +++ b/drivers/input/serio/hp_sdc_mlc.c @@ -296,7 +296,7 @@ static void hp_sdc_mlc_out(hil_mlc *mlc) priv->tseq[3] = 0; if (mlc->opacket & HIL_CTRL_APE) { priv->tseq[3] |= HP_SDC_LPC_APE_IPF; - down_trylock(&mlc->csem); + BUG_ON(down_trylock(&mlc->csem)); } enqueue: hp_sdc_enqueue_transaction(&priv->trans); -- cgit v1.2.3 From 1e0deabd35f210f22c03cc734a0335c07ae71ff3 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:17:37 +0200 Subject: parisc: dino.c - check return value of pci_assign_resource() Signed-off-by: Helge Deller --- drivers/parisc/dino.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/parisc/dino.c b/drivers/parisc/dino.c index c590974e9815..d69bde6a2343 100644 --- a/drivers/parisc/dino.c +++ b/drivers/parisc/dino.c @@ -614,7 +614,7 @@ dino_fixup_bus(struct pci_bus *bus) dev_name(&bus->self->dev), i, bus->self->resource[i].start, bus->self->resource[i].end); - pci_assign_resource(bus->self, i); + WARN_ON(pci_assign_resource(bus->self, i)); DBG("DEBUG %s after assign %d [0x%lx,0x%lx]\n", dev_name(&bus->self->dev), i, bus->self->resource[i].start, -- cgit v1.2.3 From 1a1dba32412c15c51d5fc0b9efadd2ea310356d7 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:26:51 +0200 Subject: parisc: sticore.c - check return values Signed-off-by: Helge Deller --- drivers/video/console/sticore.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/video/console/sticore.c b/drivers/video/console/sticore.c index ef7870f5ea08..857b3668b3ba 100644 --- a/drivers/video/console/sticore.c +++ b/drivers/video/console/sticore.c @@ -957,9 +957,14 @@ static int __devinit sticore_pci_init(struct pci_dev *pd, #ifdef CONFIG_PCI unsigned long fb_base, rom_base; unsigned int fb_len, rom_len; + int err; struct sti_struct *sti; - pci_enable_device(pd); + err = pci_enable_device(pd); + if (err < 0) { + dev_err(&pd->dev, "Cannot enable PCI device\n"); + return err; + } fb_base = pci_resource_start(pd, 0); fb_len = pci_resource_len(pd, 0); @@ -1048,7 +1053,7 @@ static void __devinit sti_init_roms(void) /* Register drivers for native & PCI cards */ register_parisc_driver(&pa_sti_driver); - pci_register_driver(&pci_sti_driver); + WARN_ON(pci_register_driver(&pci_sti_driver)); /* if we didn't find the given default sti, take the first one */ if (!default_sti) -- cgit v1.2.3 From c43962321e8af5309dd3ffcd78743c89581265e5 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:35:43 +0200 Subject: parisc: parisc-agp.c - use correct page_mask function Fix those compiler warnings, which indeed point to a bug: drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used Signed-off-by: Helge Deller --- drivers/char/agp/parisc-agp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/char/agp/parisc-agp.c b/drivers/char/agp/parisc-agp.c index f4bb43fb8016..e077701ae3d9 100644 --- a/drivers/char/agp/parisc-agp.c +++ b/drivers/char/agp/parisc-agp.c @@ -225,7 +225,7 @@ static const struct agp_bridge_driver parisc_agp_driver = { .configure = parisc_agp_configure, .fetch_size = parisc_agp_fetch_size, .tlb_flush = parisc_agp_tlbflush, - .mask_memory = parisc_agp_mask_memory, + .mask_memory = parisc_agp_page_mask_memory, .masks = parisc_agp_masks, .agp_enable = parisc_agp_enable, .cache_flush = global_cache_flush, -- cgit v1.2.3 From cae5a39f34d52c46ca49edfc3f297656a0fd60b7 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sun, 2 Aug 2009 15:42:39 +0200 Subject: parisc: hppb.c - fix printk format strings Fix those warnings: drivers/parisc/hppb.c: In function 'hppb_probe': drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t' drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t' drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t' Signed-off-by: Helge Deller --- drivers/parisc/hppb.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/parisc/hppb.c b/drivers/parisc/hppb.c index 13856415b432..815db175d427 100644 --- a/drivers/parisc/hppb.c +++ b/drivers/parisc/hppb.c @@ -62,7 +62,8 @@ static int hppb_probe(struct parisc_device *dev) } card = card->next; } - printk(KERN_INFO "Found GeckoBoa at 0x%x\n", dev->hpa.start); + printk(KERN_INFO "Found GeckoBoa at 0x%llx\n", + (unsigned long long) dev->hpa.start); card->hpa = dev->hpa.start; card->mmio_region.name = "HP-PB Bus"; @@ -73,8 +74,10 @@ static int hppb_probe(struct parisc_device *dev) status = ccio_request_resource(dev, &card->mmio_region); if(status < 0) { - printk(KERN_ERR "%s: failed to claim HP-PB bus space (%08x, %08x)\n", - __FILE__, card->mmio_region.start, card->mmio_region.end); + printk(KERN_ERR "%s: failed to claim HP-PB " + "bus space (0x%08llx, 0x%08llx)\n", + __FILE__, (unsigned long long) card->mmio_region.start, + (unsigned long long) card->mmio_region.end); } return 0; -- cgit v1.2.3 From d0006f3281c920fbfead0f5035c62ec8053f980a Mon Sep 17 00:00:00 2001 From: Len Brown Date: Thu, 30 Jul 2009 16:00:53 -0400 Subject: ACPI: root-only read protection on /sys/firmware/acpi/tables/* they were world readable. Signed-off-by: Len Brown --- drivers/acpi/system.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/acpi/system.c b/drivers/acpi/system.c index 0944daec064f..9c61ab2177cf 100644 --- a/drivers/acpi/system.c +++ b/drivers/acpi/system.c @@ -121,7 +121,7 @@ static void acpi_table_attr_init(struct acpi_table_attr *table_attr, table_attr->attr.size = 0; table_attr->attr.read = acpi_table_show; table_attr->attr.attr.name = table_attr->name; - table_attr->attr.attr.mode = 0444; + table_attr->attr.attr.mode = 0400; return; } -- cgit v1.2.3 From 74b5820808215f65b70b05a099d6d3c969b82689 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 29 Jul 2009 15:54:25 -0600 Subject: ACPI: bind workqueues to CPU 0 to avoid SMI corruption On some machines, a software-initiated SMI causes corruption unless the SMI runs on CPU 0. An SMI can be initiated by any AML, but typically it's done in GPE-related methods that are run via workqueues, so we can avoid the known corruption cases by binding the workqueues to CPU 0. References: http://bugzilla.kernel.org/show_bug.cgi?id=13751 https://bugs.launchpad.net/bugs/157171 https://bugs.launchpad.net/bugs/157691 Signed-off-by: Bjorn Helgaas Signed-off-by: Len Brown --- drivers/acpi/osl.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) (limited to 'drivers') diff --git a/drivers/acpi/osl.c b/drivers/acpi/osl.c index 71670719d61a..5691f165a952 100644 --- a/drivers/acpi/osl.c +++ b/drivers/acpi/osl.c @@ -189,11 +189,36 @@ acpi_status __init acpi_os_initialize(void) return AE_OK; } +static void bind_to_cpu0(struct work_struct *work) +{ + set_cpus_allowed(current, cpumask_of_cpu(0)); + kfree(work); +} + +static void bind_workqueue(struct workqueue_struct *wq) +{ + struct work_struct *work; + + work = kzalloc(sizeof(struct work_struct), GFP_KERNEL); + INIT_WORK(work, bind_to_cpu0); + queue_work(wq, work); +} + acpi_status acpi_os_initialize1(void) { + /* + * On some machines, a software-initiated SMI causes corruption unless + * the SMI runs on CPU 0. An SMI can be initiated by any AML, but + * typically it's done in GPE-related methods that are run via + * workqueues, so we can avoid the known corruption cases by binding + * the workqueues to CPU 0. + */ kacpid_wq = create_singlethread_workqueue("kacpid"); + bind_workqueue(kacpid_wq); kacpi_notify_wq = create_singlethread_workqueue("kacpi_notify"); + bind_workqueue(kacpi_notify_wq); kacpi_hotplug_wq = create_singlethread_workqueue("kacpi_hotplug"); + bind_workqueue(kacpi_hotplug_wq); BUG_ON(!kacpid_wq); BUG_ON(!kacpi_notify_wq); BUG_ON(!kacpi_hotplug_wq); -- cgit v1.2.3 From aa7b2b2e973874df99a45b31adbed5978b46be1f Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Fri, 3 Jul 2009 10:49:03 +0800 Subject: ACPI: Don't treat generic error as ACPI error code in acpi memory hotplug driver Don't treat the generic error as ACPI error code. Otherwise when the generic code is returned, it will complain the following warning messag: >ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE, Cannot get acpi bus device [20080609] >ACPI: Cannot find driver data > ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609] > Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1 Call Trace: [] show_trace_log_lvl+0x41/0x58 [] dump_stack+0x69/0x6f ..... At the same time when the generic error code is returned, the ACPI_EXCEPTION is replaced by the printk. Signed-off-by: Zhao Yakui Signed-off-by: Len Brown --- drivers/acpi/acpi_memhotplug.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c index 7a0f4aa4fa1e..37cbe72d17eb 100644 --- a/drivers/acpi/acpi_memhotplug.c +++ b/drivers/acpi/acpi_memhotplug.c @@ -38,6 +38,9 @@ #define _COMPONENT ACPI_MEMORY_DEVICE_COMPONENT +#undef PREFIX +#define PREFIX "ACPI:memory_hp:" + ACPI_MODULE_NAME("acpi_memhotplug"); MODULE_AUTHOR("Naveen B S "); MODULE_DESCRIPTION("Hotplug Mem Driver"); @@ -153,6 +156,7 @@ acpi_memory_get_device(acpi_handle handle, acpi_handle phandle; struct acpi_device *device = NULL; struct acpi_device *pdevice = NULL; + int result; if (!acpi_bus_get_device(handle, &device) && device) @@ -165,9 +169,9 @@ acpi_memory_get_device(acpi_handle handle, } /* Get the parent device */ - status = acpi_bus_get_device(phandle, &pdevice); - if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Cannot get acpi bus device")); + result = acpi_bus_get_device(phandle, &pdevice); + if (result) { + printk(KERN_WARNING PREFIX "Cannot get acpi bus device"); return -EINVAL; } @@ -175,9 +179,9 @@ acpi_memory_get_device(acpi_handle handle, * Now add the notified device. This creates the acpi_device * and invokes .add function */ - status = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE); - if (ACPI_FAILURE(status)) { - ACPI_EXCEPTION((AE_INFO, status, "Cannot add acpi bus")); + result = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE); + if (result) { + printk(KERN_WARNING PREFIX "Cannot add acpi bus"); return -EINVAL; } -- cgit v1.2.3 From 5d2619fca753d270e63e76c9e18437b0d9bc8d75 Mon Sep 17 00:00:00 2001 From: Zhao Yakui Date: Tue, 7 Jul 2009 10:56:11 +0800 Subject: ACPI: Ingore the memory block with zero block size in course of memory hotplug If the memory block size is zero, ignore it and don't do the memory hotplug flowchart. Otherwise it will complain the following warning message: >System RAM resource 0 - ffffffffffffffff cannot be added Signed-off-by: Zhao Yakui Signed-off-by: Len Brown --- drivers/acpi/acpi_memhotplug.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c index 37cbe72d17eb..9a62224cc278 100644 --- a/drivers/acpi/acpi_memhotplug.c +++ b/drivers/acpi/acpi_memhotplug.c @@ -242,7 +242,12 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device) num_enabled++; continue; } - + /* + * If the memory block size is zero, please ignore it. + * Don't try to do the following memory hotplug flowchart. + */ + if (!info->length) + continue; if (node < 0) node = memory_add_physaddr_to_nid(info->start_addr); @@ -257,8 +262,15 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device) mem_device->state = MEMORY_INVALID_STATE; return -EINVAL; } - - return result; + /* + * Sometimes the memory device will contain several memory blocks. + * When one memory block is hot-added to the system memory, it will + * be regarded as a success. + * Otherwise if the last memory block can't be hot-added to the system + * memory, it will be failure and the memory device can't be bound with + * driver. + */ + return 0; } static int acpi_memory_powerdown_device(struct acpi_memory_device *mem_device) -- cgit v1.2.3 From 7334546a52c6764df120459509b1f803a073eacc Mon Sep 17 00:00:00 2001 From: Alan Jenkins Date: Mon, 29 Jun 2009 09:40:07 +0100 Subject: eeepc-laptop: fix hot-unplug on resume OOPS on resume when the wireless adaptor is disabled during suspend was introduced by "eeepc-laptop: read rfkill soft-blocked state on resume". Unable to handle kernel NULL pointer dereference Process s2disk Tainted: G W IP: klist_put Call trace: ? klist_del ? device_del ? device_unregister ? pci_stop_dev ? pci_stop_bus ? pci_remove_device ? eeepc_rfkill_hotplug [eeepc_laptop] ? eeepc_hotk_resume [eeepc_laptop] ? acpi_device_resume ? device_resume ? hibernation_snapshot It appears the PCI device is removed twice. The eeepc_rfkill_hotplug() call from the resume handler is racing against the call from the ACPI notifier callback. The ACPI notification is triggered by the resume handler when it refreshes the value of CM_ASL_WLAN. The fix is to serialize hotplug calls using a workqueue. http://bugzilla.kernel.org/show_bug.cgi?id=13825 Signed-off-by: Alan Jenkins Acked-by: Corentin Chary Signed-off-by: Len Brown --- drivers/platform/x86/eeepc-laptop.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/platform/x86/eeepc-laptop.c b/drivers/platform/x86/eeepc-laptop.c index ec560f16d720..222ffb892f22 100644 --- a/drivers/platform/x86/eeepc-laptop.c +++ b/drivers/platform/x86/eeepc-laptop.c @@ -143,6 +143,7 @@ struct eeepc_hotk { struct rfkill *bluetooth_rfkill; struct rfkill *wwan3g_rfkill; struct hotplug_slot *hotplug_slot; + struct work_struct hotplug_work; }; /* The actual device the driver binds to */ @@ -660,7 +661,7 @@ static int eeepc_get_adapter_status(struct hotplug_slot *hotplug_slot, return 0; } -static void eeepc_rfkill_hotplug(void) +static void eeepc_hotplug_work(struct work_struct *work) { struct pci_dev *dev; struct pci_bus *bus = pci_find_bus(0, 1); @@ -701,7 +702,7 @@ static void eeepc_rfkill_notify(acpi_handle handle, u32 event, void *data) if (event != ACPI_NOTIFY_BUS_CHECK) return; - eeepc_rfkill_hotplug(); + schedule_work(&ehotk->hotplug_work); } static void eeepc_hotk_notify(struct acpi_device *device, u32 event) @@ -892,7 +893,7 @@ static int eeepc_hotk_resume(struct acpi_device *device) rfkill_set_sw_state(ehotk->wlan_rfkill, wlan != 1); - eeepc_rfkill_hotplug(); + schedule_work(&ehotk->hotplug_work); } if (ehotk->bluetooth_rfkill) @@ -1093,6 +1094,8 @@ static int eeepc_rfkill_init(struct device *dev) { int result = 0; + INIT_WORK(&ehotk->hotplug_work, eeepc_hotplug_work); + eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6"); eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7"); -- cgit v1.2.3 From a53a8b56827cc429c6d9f861ad558beeb5f6103f Mon Sep 17 00:00:00 2001 From: Ben McKeegan Date: Tue, 28 Jul 2009 07:43:57 +0000 Subject: ppp: fix lost fragments in ppp_mp_explode() (resubmit) This patch fixes the corner cases where the sum of MTU of the free channels (adjusted for fragmentation overheads) is less than the MTU of PPP link. There are at least 3 situations where this case might arise: - some of the channels are busy - the multilink session is running in a degraded state (i.e. with less than its full complement of active channels) - by design, where multilink protocol is being used to artificially increase the effective link MTU of a single link. Without this patch, at most 1 fragment is ever sent per free channel for a given PPP frame and any remaining part of the PPP frame that does not fit into those fragments is silently discarded. This patch restores the original behaviour which was broken by commit 9c705260feea6ae329bc6b6d5f6d2ef0227eda0a 'ppp:ppp_mp_explode() redesign'. Once all 'free' channels have been given a fragment, an additional fragment is queued to each available channel in turn, as many times as necessary, until the entire PPP frame has been consumed. Signed-off-by: Ben McKeegan Signed-off-by: David S. Miller --- drivers/net/ppp_generic.c | 34 ++++++++++++++++++---------------- 1 file changed, 18 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ppp_generic.c b/drivers/net/ppp_generic.c index 639d11bc444e..cd37d739ac74 100644 --- a/drivers/net/ppp_generic.c +++ b/drivers/net/ppp_generic.c @@ -1384,7 +1384,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) /* create a fragment for each channel */ bits = B; - while (nfree > 0 && len > 0) { + while (len > 0) { list = list->next; if (list == &ppp->channels) { i = 0; @@ -1431,29 +1431,31 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) *otherwise divide it according to the speed *of the channel we are going to transmit on */ - if (pch->speed == 0) { - flen = totlen/nfree ; - if (nbigger > 0) { - flen++; - nbigger--; - } - } else { - flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) / - ((totspeed*totfree)/pch->speed)) - hdrlen; - if (nbigger > 0) { - flen += ((totfree - nzero)*pch->speed)/totspeed; - nbigger -= ((totfree - nzero)*pch->speed)/ + if (nfree > 0) { + if (pch->speed == 0) { + flen = totlen/nfree ; + if (nbigger > 0) { + flen++; + nbigger--; + } + } else { + flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) / + ((totspeed*totfree)/pch->speed)) - hdrlen; + if (nbigger > 0) { + flen += ((totfree - nzero)*pch->speed)/totspeed; + nbigger -= ((totfree - nzero)*pch->speed)/ totspeed; + } } + nfree--; } - nfree--; /* *check if we are on the last channel or *we exceded the lenght of the data to *fragment */ - if ((nfree == 0) || (flen > len)) + if ((nfree <= 0) || (flen > len)) flen = len; /* *it is not worth to tx on slow channels: @@ -1467,7 +1469,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb) continue; } - mtu = pch->chan->mtu + 2 - hdrlen; + mtu = pch->chan->mtu - hdrlen; if (mtu < 4) mtu = 4; if (flen > mtu) -- cgit v1.2.3 From 446e72f30eca76d6f9a1a54adf84d2c6ba2831f8 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 28 Jul 2009 03:47:39 +0000 Subject: pppol2tp: calls unregister_pernet_gen_device() at unload time Failure to call unregister_pernet_gen_device() can exhaust memory if module is loaded/unloaded many times. Signed-off-by: Eric Dumazet Acked-by: Cyrill Gorcunov Signed-off-by: David S. Miller --- drivers/net/pppol2tp.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index e7935d09c896..e0f9219a0aea 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -2680,6 +2680,7 @@ out_unregister_pppol2tp_proto: static void __exit pppol2tp_exit(void) { unregister_pppox_proto(PX_PROTO_OL2TP); + unregister_pernet_gen_device(pppol2tp_net_id, &pppol2tp_net_ops); proto_unregister(&pppol2tp_sk_proto); } -- cgit v1.2.3 From 1b994b5a1b3cb5395598a08ef3bb0ac118d75c1b Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 1 Aug 2009 20:26:52 +0000 Subject: tulip: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/tulip/de4x5.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/tulip/de4x5.c index eb72d2e9ab3d..acfdccd44567 100644 --- a/drivers/net/tulip/de4x5.c +++ b/drivers/net/tulip/de4x5.c @@ -5059,7 +5059,7 @@ mii_get_phy(struct net_device *dev) if ((id == 0) || (id == 65535)) continue; /* Valid ID? */ for (j=0; jphy[k].id && (k < DE4X5_MAX_PHY); k++); + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++); if (k < DE4X5_MAX_PHY) { memcpy((char *)&lp->phy[k], (char *)&phy_info[j], sizeof(struct phy_table)); @@ -5072,7 +5072,7 @@ mii_get_phy(struct net_device *dev) break; } if ((j == limit) && (i < DE4X5_MAX_MII)) { - for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++); + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++); lp->phy[k].addr = i; lp->phy[k].id = id; lp->phy[k].spd.reg = GENERIC_REG; /* ANLPA register */ @@ -5091,7 +5091,7 @@ mii_get_phy(struct net_device *dev) purgatory: lp->active = 0; if (lp->phy[0].id) { /* Reset the PHY devices */ - for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++) { /*For each PHY*/ + for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++) { /*For each PHY*/ mii_wr(MII_CR_RST, MII_CR, lp->phy[k].addr, DE4X5_MII); while (mii_rd(MII_CR, lp->phy[k].addr, DE4X5_MII) & MII_CR_RST); -- cgit v1.2.3 From 54706d99051582993037be5a076aa543fd7f1c38 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 1 Aug 2009 20:20:13 +0000 Subject: s6gmac: Read buffer overflow Check whether index is within bounds before testing the element. In the last iteration i is PHY_MAX_ADDR. the condition `!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may evaluate to false, which leads to a dereference of this invalid phy_map in the phy_connect() below. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/s6gmac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/s6gmac.c b/drivers/net/s6gmac.c index 5345e47b35ac..4525cbe8dd69 100644 --- a/drivers/net/s6gmac.c +++ b/drivers/net/s6gmac.c @@ -793,7 +793,7 @@ static inline int s6gmac_phy_start(struct net_device *dev) struct s6gmac *pd = netdev_priv(dev); int i = 0; struct phy_device *p = NULL; - while ((!(p = pd->mii.bus->phy_map[i])) && (i < PHY_MAX_ADDR)) + while ((i < PHY_MAX_ADDR) && (!(p = pd->mii.bus->phy_map[i]))) i++; p = phy_connect(dev, dev_name(&p->dev), &s6gmac_adjust_link, 0, PHY_INTERFACE_MODE_RGMII); -- cgit v1.2.3 From 9bfdac94c78faf68ce038d5c45a385927f2667ce Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 31 Jul 2009 03:43:59 +0000 Subject: mISDN: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Acked-by: Karsten Keil Signed-off-by: David S. Miller --- drivers/isdn/mISDN/l1oip_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 990e6a7e6674..0ebce046ade4 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -1480,7 +1480,7 @@ l1oip_init(void) return -ENOMEM; l1oip_cnt = 0; - while (type[l1oip_cnt] && l1oip_cnt < MAX_CARDS) { + while (l1oip_cnt < MAX_CARDS && type[l1oip_cnt]) { switch (type[l1oip_cnt] & 0xff) { case 1: pri = 0; -- cgit v1.2.3 From 50c643e7652458e649955408685a16e88ea6dbae Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Sat, 1 Aug 2009 21:36:16 +0000 Subject: netxen: fix coherent dma mask setting Change default dma mask for NX3031 to 39 bit with ability to update it to 64-bit (if firmware indicates support). Old code was restricting it under 4GB (32-bit), sometimes causing failure to allocate descriptor rings on heavily populated system. NX2031 based NICs will still get 32-bit coherent mask. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 37 ++++++++++++++++++++++++------------ 1 file changed, 25 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 637ac8b89bac..3cd8cfcf627b 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -221,7 +221,7 @@ netxen_napi_disable(struct netxen_adapter *adapter) } } -static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id) +static int nx_set_dma_mask(struct netxen_adapter *adapter) { struct pci_dev *pdev = adapter->pdev; uint64_t mask, cmask; @@ -229,19 +229,17 @@ static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id) adapter->pci_using_dac = 0; mask = DMA_BIT_MASK(32); - /* - * Consistent DMA mask is set to 32 bit because it cannot be set to - * 35 bits. For P3 also leave it at 32 bits for now. Only the rings - * come off this pool. - */ cmask = DMA_BIT_MASK(32); + if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) { #ifndef CONFIG_IA64 - if (revision_id >= NX_P3_B0) - mask = DMA_BIT_MASK(39); - else if (revision_id == NX_P2_C1) mask = DMA_BIT_MASK(35); #endif + } else { + mask = DMA_BIT_MASK(39); + cmask = mask; + } + if (pci_set_dma_mask(pdev, mask) == 0 && pci_set_consistent_dma_mask(pdev, cmask) == 0) { adapter->pci_using_dac = 1; @@ -256,7 +254,7 @@ static int nx_update_dma_mask(struct netxen_adapter *adapter) { int change, shift, err; - uint64_t mask, old_mask; + uint64_t mask, old_mask, old_cmask; struct pci_dev *pdev = adapter->pdev; change = 0; @@ -272,14 +270,29 @@ nx_update_dma_mask(struct netxen_adapter *adapter) if (change) { old_mask = pdev->dma_mask; + old_cmask = pdev->dev.coherent_dma_mask; + mask = (1ULL<<(32+shift)) - 1; err = pci_set_dma_mask(pdev, mask); if (err) - return pci_set_dma_mask(pdev, old_mask); + goto err_out; + + if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) { + + err = pci_set_consistent_dma_mask(pdev, mask); + if (err) + goto err_out; + } + dev_info(&pdev->dev, "using %d-bit dma mask\n", 32+shift); } return 0; + +err_out: + pci_set_dma_mask(pdev, old_mask); + pci_set_consistent_dma_mask(pdev, old_cmask); + return err; } static void netxen_check_options(struct netxen_adapter *adapter) @@ -1006,7 +1019,7 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) revision_id = pdev->revision; adapter->ahw.revision_id = revision_id; - err = nx_set_dma_mask(adapter, revision_id); + err = nx_set_dma_mask(adapter); if (err) goto err_out_free_netdev; -- cgit v1.2.3 From df4e7f72f5156ef16a918da8a575ba90ec27ab77 Mon Sep 17 00:00:00 2001 From: Don Fry Date: Fri, 31 Jul 2009 08:40:06 +0000 Subject: pcnet32: remove superfluous NULL pointer check in pcnet32_probe1() Move the debug printk() into the proper place and remove superfluous NULL pointer check in pcnet32_probe1(). This takes care of the following entry from Dan's list: drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev' Reported-by: Dan Carpenter Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Don Fry Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 18 +++++++----------- 1 file changed, 7 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index 1c35e1d637a0..b61c97254b3f 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1611,8 +1611,11 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) if (pcnet32_dwio_read_csr(ioaddr, 0) == 4 && pcnet32_dwio_check(ioaddr)) { a = &pcnet32_dwio; - } else + } else { + if (pcnet32_debug & NETIF_MSG_PROBE) + printk(KERN_ERR PFX "No access methods\n"); goto err_release_region; + } } chip_version = @@ -1852,12 +1855,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) ((cards_found >= MAX_UNITS) || full_duplex[cards_found])) lp->options |= PCNET32_PORT_FD; - if (!a) { - if (pcnet32_debug & NETIF_MSG_PROBE) - printk(KERN_ERR PFX "No access methods\n"); - ret = -ENODEV; - goto err_free_consistent; - } lp->a = *a; /* prior to register_netdev, dev->name is not yet correct */ @@ -1973,14 +1970,13 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) return 0; - err_free_ring: +err_free_ring: pcnet32_free_ring(dev); - err_free_consistent: pci_free_consistent(lp->pci_dev, sizeof(*lp->init_block), lp->init_block, lp->init_dma_addr); - err_free_netdev: +err_free_netdev: free_netdev(dev); - err_release_region: +err_release_region: release_region(ioaddr, PCNET32_TOTAL_SIZE); return ret; } -- cgit v1.2.3 From 63097b3ad85788a64c75091bff351ecc850761b2 Mon Sep 17 00:00:00 2001 From: Don Fry Date: Fri, 31 Jul 2009 08:45:29 +0000 Subject: pcnet32: VLB support fixes VLB support has been broken since at least 2004-2005 period as some changes introduced back then assumed that ->pci_dev is always valid, lets try to fix it: - remove duplicated SET_NETDEV_DEV() call - call SET_NETDEV_DEV() only for PCI devices - check for ->pci_dev validity in pcnet32_open() [ Alternatively we may consider removing VLB support but there would not be much gain in it since an extra driver code needed for VLB support is minimal and quite simple. ] This takes care of the following entry from Dan's list: drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev' Reported-by: Dan Carpenter Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Don Fry Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index b61c97254b3f..16964ec73e67 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1722,7 +1722,9 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) ret = -ENOMEM; goto err_release_region; } - SET_NETDEV_DEV(dev, &pdev->dev); + + if (pdev) + SET_NETDEV_DEV(dev, &pdev->dev); if (pcnet32_debug & NETIF_MSG_PROBE) printk(KERN_INFO PFX "%s at %#3lx,", chipname, ioaddr); @@ -1821,7 +1823,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) spin_lock_init(&lp->lock); - SET_NETDEV_DEV(dev, &pdev->dev); lp->name = chipname; lp->shared_irq = shared; lp->tx_ring_size = TX_RING_SIZE; /* default tx ring size */ @@ -2085,6 +2086,7 @@ static void pcnet32_free_ring(struct net_device *dev) static int pcnet32_open(struct net_device *dev) { struct pcnet32_private *lp = netdev_priv(dev); + struct pci_dev *pdev = lp->pci_dev; unsigned long ioaddr = dev->base_addr; u16 val; int i; @@ -2145,9 +2147,9 @@ static int pcnet32_open(struct net_device *dev) lp->a.write_csr(ioaddr, 124, val); /* Allied Telesyn AT 2700/2701 FX are 100Mbit only and do not negotiate */ - if (lp->pci_dev->subsystem_vendor == PCI_VENDOR_ID_AT && - (lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX || - lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) { + if (pdev && pdev->subsystem_vendor == PCI_VENDOR_ID_AT && + (pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX || + pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) { if (lp->options & PCNET32_PORT_ASEL) { lp->options = PCNET32_PORT_FD | PCNET32_PORT_100; if (netif_msg_link(lp)) -- cgit v1.2.3 From 5973bee46fe66db94fab198979dec87f263fc2a8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 21 Jul 2009 00:40:46 +0200 Subject: [WATCHDOG] Fix COH 901 327 watchdog enablement Since the COH 901 327 found in U300 is clocked at 32 kHz we need to wait for the interrupt clearing flag to propagate through hardware in order not to accidentally fire off any interrupts when we enable them. Signed-off-by: Linus Walleij Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/coh901327_wdt.c | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'drivers') diff --git a/drivers/watchdog/coh901327_wdt.c b/drivers/watchdog/coh901327_wdt.c index fecb307d28e9..aec7cefdef21 100644 --- a/drivers/watchdog/coh901327_wdt.c +++ b/drivers/watchdog/coh901327_wdt.c @@ -18,6 +18,7 @@ #include #include #include +#include #define DRV_NAME "WDOG COH 901 327" @@ -92,6 +93,8 @@ static struct clk *clk; static void coh901327_enable(u16 timeout) { u16 val; + unsigned long freq; + unsigned long delay_ns; clk_enable(clk); /* Restart timer if it is disabled */ @@ -102,6 +105,14 @@ static void coh901327_enable(u16 timeout) /* Acknowledge any pending interrupt so it doesn't just fire off */ writew(U300_WDOG_IER_WILL_BARK_IRQ_ACK_ENABLE, virtbase + U300_WDOG_IER); + /* + * The interrupt is cleared in the 32 kHz clock domain. + * Wait 3 32 kHz cycles for it to take effect + */ + freq = clk_get_rate(clk); + delay_ns = (1000000000 + freq - 1) / freq; /* Freq to ns and round up */ + delay_ns = 3 * delay_ns; /* Wait 3 cycles */ + ndelay(delay_ns); /* Enable the watchdog interrupt */ writew(U300_WDOG_IMR_WILL_BARK_IRQ_ENABLE, virtbase + U300_WDOG_IMR); /* Activate the watchdog timer */ -- cgit v1.2.3 From b564afcfb82fe3e63a7ce05a944eb5e11244d7cb Mon Sep 17 00:00:00 2001 From: Andreas Eversberg Date: Mon, 27 Jul 2009 07:24:04 +0000 Subject: mISDN: Fix handling of receive buffer size in L1oIP The size of receive buffer pointer was used to get size of receive buffer instead of recvbuf_size itself, so only 4/8 bytes could be transfered. This is a regression to 2.6.30 introduced by commit 8c90e11e3543d7de612194a042a148caeaab5f1d mISDN: Use kernel_{send,recv}msg instead of open coding Signed-off-by: Andreas Eversberg Signed-off-by: Karsten Keil Signed-off-by: David S. Miller --- drivers/isdn/mISDN/l1oip_core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c index 0ebce046ade4..7e5f30dbc0a0 100644 --- a/drivers/isdn/mISDN/l1oip_core.c +++ b/drivers/isdn/mISDN/l1oip_core.c @@ -731,10 +731,10 @@ l1oip_socket_thread(void *data) while (!signal_pending(current)) { struct kvec iov = { .iov_base = recvbuf, - .iov_len = sizeof(recvbuf), + .iov_len = recvbuf_size, }; recvlen = kernel_recvmsg(socket, &msg, &iov, 1, - sizeof(recvbuf), 0); + recvbuf_size, 0); if (recvlen > 0) { l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen); } else { -- cgit v1.2.3 From 79896cf42f6a96d7e14f2dc3473443d68d74031d Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sun, 2 Aug 2009 14:04:19 -0700 Subject: Make pci_claim_resource() use request_resource() rather than insert_resource() This function has traditionally used "insert_resource()", because before commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the resource into whatever root resource tree that was indicated by "pcibios_select_root()". So there Matthew fixed it to actually look up the proper parent resource, which means that now it's actively wrong to then traverse the resource tree any more: we already know exactly where the new resource should go. And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"), which changed the x86 PCI code from the open-coded pr = pci_find_parent_resource(dev, r); if (!pr || request_resource(pr, r) < 0) { to using if (pci_claim_resource(dev, idx) < 0) { that "insert_resource()" now suddenly became a problem, and causes a regression covered by http://bugzilla.kernel.org/show_bug.cgi?id=13891 which this fixes. Reported-and-tested-by: Rafael J. Wysocki Cc: Matthew Wilcox Cc: Andrew Patterson Cc: Linux PCI Signed-off-by: Linus Torvalds --- drivers/pci/setup-res.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c index b711fb7181e2..1898c7b47907 100644 --- a/drivers/pci/setup-res.c +++ b/drivers/pci/setup-res.c @@ -100,16 +100,16 @@ int pci_claim_resource(struct pci_dev *dev, int resource) { struct resource *res = &dev->resource[resource]; struct resource *root; - char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge"; int err; root = pci_find_parent_resource(dev, res); err = -EINVAL; if (root != NULL) - err = insert_resource(root, res); + err = request_resource(root, res); if (err) { + const char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge"; dev_err(&dev->dev, "BAR %d: %s of %s %pR\n", resource, root ? "address space collision on" : -- cgit v1.2.3 From ac5e7113e74872928844d00085bd47c988f12728 Mon Sep 17 00:00:00 2001 From: Andre Noll Date: Mon, 3 Aug 2009 10:59:47 +1000 Subject: md: Push down data integrity code to personalities. This patch replaces md_integrity_check() by two new public functions: md_integrity_register() and md_integrity_add_rdev() which are both personality-independent. md_integrity_register() is called from the ->run and ->hot_remove methods of all personalities that support data integrity. The function iterates over the component devices of the array and determines if all active devices are integrity capable and if their profiles match. If this is the case, the common profile is registered for the mddev via blk_integrity_register(). The second new function, md_integrity_add_rdev() is called from the ->hot_add_disk methods, i.e. whenever a new device is being added to a raid array. If the new device does not support data integrity, or has a profile different from the one already registered, data integrity for the mddev is disabled. For raid0 and linear, only the call to md_integrity_register() from the ->run method is necessary. Signed-off-by: Andre Noll Signed-off-by: NeilBrown --- drivers/md/linear.c | 1 + drivers/md/md.c | 94 ++++++++++++++++++++++++++++++++++---------------- drivers/md/md.h | 2 ++ drivers/md/multipath.c | 5 ++- drivers/md/raid0.c | 1 + drivers/md/raid1.c | 6 ++-- drivers/md/raid10.c | 4 +++ 7 files changed, 80 insertions(+), 33 deletions(-) (limited to 'drivers') diff --git a/drivers/md/linear.c b/drivers/md/linear.c index 5810fa906af0..54c8677f1e59 100644 --- a/drivers/md/linear.c +++ b/drivers/md/linear.c @@ -220,6 +220,7 @@ static int linear_run (mddev_t *mddev) mddev->queue->unplug_fn = linear_unplug; mddev->queue->backing_dev_info.congested_fn = linear_congested; mddev->queue->backing_dev_info.congested_data = mddev; + md_integrity_register(mddev); return 0; } diff --git a/drivers/md/md.c b/drivers/md/md.c index d4351ff0849f..180949e94a7b 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1487,37 +1487,76 @@ static int match_mddev_units(mddev_t *mddev1, mddev_t *mddev2) static LIST_HEAD(pending_raid_disks); -static void md_integrity_check(mdk_rdev_t *rdev, mddev_t *mddev) +/* + * Try to register data integrity profile for an mddev + * + * This is called when an array is started and after a disk has been kicked + * from the array. It only succeeds if all working and active component devices + * are integrity capable with matching profiles. + */ +int md_integrity_register(mddev_t *mddev) +{ + mdk_rdev_t *rdev, *reference = NULL; + + if (list_empty(&mddev->disks)) + return 0; /* nothing to do */ + if (blk_get_integrity(mddev->gendisk)) + return 0; /* already registered */ + list_for_each_entry(rdev, &mddev->disks, same_set) { + /* skip spares and non-functional disks */ + if (test_bit(Faulty, &rdev->flags)) + continue; + if (rdev->raid_disk < 0) + continue; + /* + * If at least one rdev is not integrity capable, we can not + * enable data integrity for the md device. + */ + if (!bdev_get_integrity(rdev->bdev)) + return -EINVAL; + if (!reference) { + /* Use the first rdev as the reference */ + reference = rdev; + continue; + } + /* does this rdev's profile match the reference profile? */ + if (blk_integrity_compare(reference->bdev->bd_disk, + rdev->bdev->bd_disk) < 0) + return -EINVAL; + } + /* + * All component devices are integrity capable and have matching + * profiles, register the common profile for the md device. + */ + if (blk_integrity_register(mddev->gendisk, + bdev_get_integrity(reference->bdev)) != 0) { + printk(KERN_ERR "md: failed to register integrity for %s\n", + mdname(mddev)); + return -EINVAL; + } + printk(KERN_NOTICE "md: data integrity on %s enabled\n", + mdname(mddev)); + return 0; +} +EXPORT_SYMBOL(md_integrity_register); + +/* Disable data integrity if non-capable/non-matching disk is being added */ +void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev) { - struct mdk_personality *pers = mddev->pers; - struct gendisk *disk = mddev->gendisk; struct blk_integrity *bi_rdev = bdev_get_integrity(rdev->bdev); - struct blk_integrity *bi_mddev = blk_get_integrity(disk); + struct blk_integrity *bi_mddev = blk_get_integrity(mddev->gendisk); - /* Data integrity passthrough not supported on RAID 4, 5 and 6 */ - if (pers && pers->level >= 4 && pers->level <= 6) + if (!bi_mddev) /* nothing to do */ return; - - /* If rdev is integrity capable, register profile for mddev */ - if (!bi_mddev && bi_rdev) { - if (blk_integrity_register(disk, bi_rdev)) - printk(KERN_ERR "%s: %s Could not register integrity!\n", - __func__, disk->disk_name); - else - printk(KERN_NOTICE "Enabling data integrity on %s\n", - disk->disk_name); + if (rdev->raid_disk < 0) /* skip spares */ return; - } - - /* Check that mddev and rdev have matching profiles */ - if (blk_integrity_compare(disk, rdev->bdev->bd_disk) < 0) { - printk(KERN_ERR "%s: %s/%s integrity mismatch!\n", __func__, - disk->disk_name, rdev->bdev->bd_disk->disk_name); - printk(KERN_NOTICE "Disabling data integrity on %s\n", - disk->disk_name); - blk_integrity_unregister(disk); - } + if (bi_rdev && blk_integrity_compare(mddev->gendisk, + rdev->bdev->bd_disk) >= 0) + return; + printk(KERN_NOTICE "disabling data integrity on %s\n", mdname(mddev)); + blk_integrity_unregister(mddev->gendisk); } +EXPORT_SYMBOL(md_integrity_add_rdev); static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev) { @@ -1591,7 +1630,6 @@ static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev) /* May as well allow recovery to be retried once */ mddev->recovery_disabled = 0; - md_integrity_check(rdev, mddev); return 0; fail: @@ -4048,10 +4086,6 @@ static int do_md_run(mddev_t * mddev) } strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel)); - if (pers->level >= 4 && pers->level <= 6) - /* Cannot support integrity (yet) */ - blk_integrity_unregister(mddev->gendisk); - if (mddev->reshape_position != MaxSector && pers->start_reshape == NULL) { /* This personality cannot handle reshaping... */ diff --git a/drivers/md/md.h b/drivers/md/md.h index 9430a110db93..78f03168baf9 100644 --- a/drivers/md/md.h +++ b/drivers/md/md.h @@ -431,5 +431,7 @@ extern int md_allow_write(mddev_t *mddev); extern void md_wait_for_blocked_rdev(mdk_rdev_t *rdev, mddev_t *mddev); extern void md_set_array_sectors(mddev_t *mddev, sector_t array_sectors); extern int md_check_no_bitmap(mddev_t *mddev); +extern int md_integrity_register(mddev_t *mddev); +void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev); #endif /* _MD_MD_H */ diff --git a/drivers/md/multipath.c b/drivers/md/multipath.c index 237fe3fd235c..7140909f6662 100644 --- a/drivers/md/multipath.c +++ b/drivers/md/multipath.c @@ -313,6 +313,7 @@ static int multipath_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) set_bit(In_sync, &rdev->flags); rcu_assign_pointer(p->rdev, rdev); err = 0; + md_integrity_add_rdev(rdev, mddev); break; } @@ -345,7 +346,9 @@ static int multipath_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -519,7 +522,7 @@ static int multipath_run (mddev_t *mddev) mddev->queue->unplug_fn = multipath_unplug; mddev->queue->backing_dev_info.congested_fn = multipath_congested; mddev->queue->backing_dev_info.congested_data = mddev; - + md_integrity_register(mddev); return 0; out_free_conf: diff --git a/drivers/md/raid0.c b/drivers/md/raid0.c index 335f490dcad6..898e2bdfee47 100644 --- a/drivers/md/raid0.c +++ b/drivers/md/raid0.c @@ -351,6 +351,7 @@ static int raid0_run(mddev_t *mddev) blk_queue_merge_bvec(mddev->queue, raid0_mergeable_bvec); dump_zones(mddev); + md_integrity_register(mddev); return 0; } diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 0569efba0c02..67e794d0097f 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -1144,7 +1144,7 @@ static int raid1_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) rcu_assign_pointer(p->rdev, rdev); break; } - + md_integrity_add_rdev(rdev, mddev); print_conf(conf); return err; } @@ -1178,7 +1178,9 @@ static int raid1_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -2067,7 +2069,7 @@ static int run(mddev_t *mddev) mddev->queue->unplug_fn = raid1_unplug; mddev->queue->backing_dev_info.congested_fn = raid1_congested; mddev->queue->backing_dev_info.congested_data = mddev; - + md_integrity_register(mddev); return 0; out_no_mem: diff --git a/drivers/md/raid10.c b/drivers/md/raid10.c index 7298a5e5a183..3d9020cf6f6e 100644 --- a/drivers/md/raid10.c +++ b/drivers/md/raid10.c @@ -1170,6 +1170,7 @@ static int raid10_add_disk(mddev_t *mddev, mdk_rdev_t *rdev) break; } + md_integrity_add_rdev(rdev, mddev); print_conf(conf); return err; } @@ -1203,7 +1204,9 @@ static int raid10_remove_disk(mddev_t *mddev, int number) /* lost the race, try later */ err = -EBUSY; p->rdev = rdev; + goto abort; } + md_integrity_register(mddev); } abort: @@ -2225,6 +2228,7 @@ static int run(mddev_t *mddev) if (conf->near_copies < mddev->raid_disks) blk_queue_merge_bvec(mddev->queue, raid10_mergeable_bvec); + md_integrity_register(mddev); return 0; out_free_conf: -- cgit v1.2.3 From 3a981b03f38dc3b8a69b77cbc679e66c1318a44a Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:55 +1000 Subject: md: when a level change reduces the number of devices, remove the excess. When an array is changed from RAID6 to RAID5, fewer drives are needed. So any device that is made superfluous by the level conversion must be marked as not-active. For the RAID6->RAID5 conversion, this will be a drive which only has 'Q' blocks on it. Cc: stable@kernel.org Signed-off-by: NeilBrown --- drivers/md/md.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index 180949e94a7b..c194955aecae 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -2695,6 +2695,7 @@ level_store(mddev_t *mddev, const char *buf, size_t len) ssize_t rv = len; struct mdk_personality *pers; void *priv; + mdk_rdev_t *rdev; if (mddev->pers == NULL) { if (len == 0) @@ -2774,6 +2775,12 @@ level_store(mddev_t *mddev, const char *buf, size_t len) mddev_suspend(mddev); mddev->pers->stop(mddev); module_put(mddev->pers->owner); + /* Invalidate devices that are now superfluous */ + list_for_each_entry(rdev, &mddev->disks, same_set) + if (rdev->raid_disk >= mddev->raid_disks) { + rdev->raid_disk = -1; + clear_bit(In_sync, &rdev->flags); + } mddev->pers = pers; mddev->private = priv; strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel)); -- cgit v1.2.3 From 3673f305faf1bc66ead751344f8262ace851ff44 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:56 +1000 Subject: md: avoid array overflow with bad v1.x metadata We trust the 'desc_nr' field in v1.x metadata enough to use it as an index in an array. This isn't really safe. So range-check the value first. Signed-off-by: NeilBrown --- drivers/md/md.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index c194955aecae..249b2896d4ea 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1308,7 +1308,12 @@ static int super_1_validate(mddev_t *mddev, mdk_rdev_t *rdev) } if (mddev->level != LEVEL_MULTIPATH) { int role; - role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]); + if (rdev->desc_nr < 0 || + rdev->desc_nr >= le32_to_cpu(sb->max_dev)) { + role = 0xffff; + rdev->desc_nr = -1; + } else + role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]); switch(role) { case 0xffff: /* spare */ break; -- cgit v1.2.3 From 70471dafe3390243c598a3165dfb86b8b8b3f4fe Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:57 +1000 Subject: md: Handle growth of v1.x metadata correctly. The v1.x metadata does not have a fixed size and can grow when devices are added. If it grows enough to require an extra sector of storage, we need to update the 'sb_size' to match. Without this, md can write out an incomplete superblock with a bad checksum, which will be rejected when trying to re-assemble the array. Cc: stable@kernel.org Signed-off-by: NeilBrown --- drivers/md/md.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index 249b2896d4ea..52c988b072d0 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1399,8 +1399,14 @@ static void super_1_sync(mddev_t *mddev, mdk_rdev_t *rdev) if (rdev2->desc_nr+1 > max_dev) max_dev = rdev2->desc_nr+1; - if (max_dev > le32_to_cpu(sb->max_dev)) + if (max_dev > le32_to_cpu(sb->max_dev)) { + int bmask; sb->max_dev = cpu_to_le32(max_dev); + rdev->sb_size = max_dev * 2 + 256; + bmask = queue_logical_block_size(rdev->bdev->bd_disk->queue)-1; + if (rdev->sb_size & bmask) + rdev->sb_size = (rdev->sb_size | bmask) + 1; + } for (i=0; idev_roles[i] = cpu_to_le16(0xfffe); -- cgit v1.2.3 From e516402c0d4fc02be4af9fa8c18954d4f9deb44e Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:57 +1000 Subject: md/raid5: set reshape_position correctly when reshape starts. As the internal reshape_progress counter is the main driver for reshape, the fact that reshape_position sometimes starts with the wrong value has minimal effect. It is visible in sysfs and that is all. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 39374230a463..659151e5eda4 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -5000,7 +5000,7 @@ static int raid5_start_reshape(mddev_t *mddev) spin_unlock_irqrestore(&conf->device_lock, flags); } mddev->raid_disks = conf->raid_disks; - mddev->reshape_position = 0; + mddev->reshape_position = conf->reshape_progress; set_bit(MD_CHANGE_DEVS, &mddev->flags); clear_bit(MD_RECOVERY_SYNC, &mddev->recovery); -- cgit v1.2.3 From 64bd660b51b2da92e99a5e97349f6558349f11c5 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:58 +1000 Subject: md: allow raid5_quiesce to work properly when reshape is happening. The ->quiesce method is not supposed to stop resync/recovery/reshape, just normal IO. But in raid5 we don't have a way to know which stripes are being used for normal IO and which for resync etc, so we need to wait for all stripes to be idle to be sure that all writes have completed. However reshape keeps at least some stripe busy for an extended period of time, so a call to raid5_quiesce can block for several seconds needlessly. So arrange for reshape etc to pause briefly while raid5_quiesce is trying to quiesce the array so that the active_stripes count can drop to zero. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 659151e5eda4..2dc35b4c20ac 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -3999,6 +3999,9 @@ static inline sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *ski return 0; } + /* Allow raid5_quiesce to complete */ + wait_event(conf->wait_for_overlap, conf->quiesce != 2); + if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery)) return reshape_request(mddev, sector_nr, skipped); @@ -5104,12 +5107,18 @@ static void raid5_quiesce(mddev_t *mddev, int state) case 1: /* stop all writes */ spin_lock_irq(&conf->device_lock); - conf->quiesce = 1; + /* '2' tells resync/reshape to pause so that all + * active stripes can drain + */ + conf->quiesce = 2; wait_event_lock_irq(conf->wait_for_stripe, atomic_read(&conf->active_stripes) == 0 && atomic_read(&conf->active_aligned_reads) == 0, conf->device_lock, /* nothing */); + conf->quiesce = 1; spin_unlock_irq(&conf->device_lock); + /* allow reshape to continue */ + wake_up(&conf->wait_for_overlap); break; case 0: /* re-enable writes */ -- cgit v1.2.3 From 449aad3e25358812c43afc60918c5ad3819488e7 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 3 Aug 2009 10:59:58 +1000 Subject: md: Use revalidate_disk to effect changes in size of device. As revalidate_disk calls check_disk_size_change, it will cause any capacity change of a gendisk to be propagated to the blockdev inode. So use that instead of mucking about with locks and i_size_write. Also add a call to revalidate_disk in do_md_run and a few other places where the gendisk capacity is changed. Signed-off-by: NeilBrown --- drivers/md/linear.c | 1 + drivers/md/md.c | 28 +++++----------------------- drivers/md/raid1.c | 1 + drivers/md/raid5.c | 12 ++---------- 4 files changed, 9 insertions(+), 33 deletions(-) (limited to 'drivers') diff --git a/drivers/md/linear.c b/drivers/md/linear.c index 54c8677f1e59..5fe39c2a3d2b 100644 --- a/drivers/md/linear.c +++ b/drivers/md/linear.c @@ -257,6 +257,7 @@ static int linear_add(mddev_t *mddev, mdk_rdev_t *rdev) rcu_assign_pointer(mddev->private, newconf); md_set_array_sectors(mddev, linear_size(mddev, 0, 0)); set_capacity(mddev->gendisk, mddev->array_sectors); + revalidate_disk(mddev->gendisk); call_rcu(&oldconf->rcu, free_conf); return 0; } diff --git a/drivers/md/md.c b/drivers/md/md.c index 52c988b072d0..5b98bea4ff9b 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -3741,17 +3741,8 @@ array_size_store(mddev_t *mddev, const char *buf, size_t len) mddev->array_sectors = sectors; set_capacity(mddev->gendisk, mddev->array_sectors); - if (mddev->pers) { - struct block_device *bdev = bdget_disk(mddev->gendisk, 0); - - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } - } + if (mddev->pers) + revalidate_disk(mddev->gendisk); return len; } @@ -4241,6 +4232,7 @@ static int do_md_run(mddev_t * mddev) md_wakeup_thread(mddev->thread); md_wakeup_thread(mddev->sync_thread); /* possibly kick off a reshape */ + revalidate_disk(mddev->gendisk); mddev->changed = 1; md_new_event(mddev); sysfs_notify_dirent(mddev->sysfs_state); @@ -5139,18 +5131,8 @@ static int update_size(mddev_t *mddev, sector_t num_sectors) return -ENOSPC; } rv = mddev->pers->resize(mddev, num_sectors); - if (!rv) { - struct block_device *bdev; - - bdev = bdget_disk(mddev->gendisk, 0); - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } - } + if (!rv) + revalidate_disk(mddev->gendisk); return rv; } diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c index 67e794d0097f..8726fd7ebce5 100644 --- a/drivers/md/raid1.c +++ b/drivers/md/raid1.c @@ -2134,6 +2134,7 @@ static int raid1_resize(mddev_t *mddev, sector_t sectors) return -EINVAL; set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; + revalidate_disk(mddev->gendisk); if (sectors > mddev->dev_sectors && mddev->recovery_cp == MaxSector) { mddev->recovery_cp = mddev->dev_sectors; diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 2dc35b4c20ac..2b521ee67dfa 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4858,6 +4858,7 @@ static int raid5_resize(mddev_t *mddev, sector_t sectors) return -EINVAL; set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; + revalidate_disk(mddev->gendisk); if (sectors > mddev->dev_sectors && mddev->recovery_cp == MaxSector) { mddev->recovery_cp = mddev->dev_sectors; set_bit(MD_RECOVERY_NEEDED, &mddev->recovery); @@ -5058,7 +5059,6 @@ static void end_reshape(raid5_conf_t *conf) */ static void raid5_finish_reshape(mddev_t *mddev) { - struct block_device *bdev; raid5_conf_t *conf = mddev->private; if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery)) { @@ -5067,15 +5067,7 @@ static void raid5_finish_reshape(mddev_t *mddev) md_set_array_sectors(mddev, raid5_size(mddev, 0, 0)); set_capacity(mddev->gendisk, mddev->array_sectors); mddev->changed = 1; - - bdev = bdget_disk(mddev->gendisk, 0); - if (bdev) { - mutex_lock(&bdev->bd_inode->i_mutex); - i_size_write(bdev->bd_inode, - (loff_t)mddev->array_sectors << 9); - mutex_unlock(&bdev->bd_inode->i_mutex); - bdput(bdev); - } + revalidate_disk(mddev->gendisk); } else { int d; mddev->degraded = conf->raid_disks; -- cgit v1.2.3 From eb4ad826419ab5b1260bc1625249114767d36bea Mon Sep 17 00:00:00 2001 From: Yevgeny Petrilin Date: Sun, 2 Aug 2009 20:22:18 -0700 Subject: mlx4_en: Fix double pci unmapping. In cases of fragmented skb, with the data pointers being wrapped around the TX buffer, the completion handling code would not forward the data pointer and the firs fragment was unmapped several times, while others were not unmapped at all. Signed-off-by: Yevgeny Petrilin Signed-off-by: David S. Miller --- drivers/net/mlx4/en_tx.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c index 08c43f2ae72b..5a88b3f57693 100644 --- a/drivers/net/mlx4/en_tx.c +++ b/drivers/net/mlx4/en_tx.c @@ -249,6 +249,7 @@ static u32 mlx4_en_free_tx_desc(struct mlx4_en_priv *priv, pci_unmap_page(mdev->pdev, (dma_addr_t) be64_to_cpu(data->addr), frag->size, PCI_DMA_TODEVICE); + ++data; } } /* Stamp the freed descriptor */ -- cgit v1.2.3 From 6afc4fdb3e94ba60cd566cb878b60c6c01979277 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Tue, 28 Jul 2009 04:56:43 -0700 Subject: mtd: fix the conversion from dev to mtd_info The patch fixes a bug when converting dev to mtd_info by using the drvdata of the dev, the previous code used container_of(dev, struct mtd_info, dev), but won't work for the mtdXro devices as they created without being contained inside mtd_info structure. Signed-off-by: Saeed Bishara Signed-off-by: David Woodhouse --- drivers/mtd/mtdcore.c | 7 ++++--- include/linux/mtd/mtd.h | 2 +- 2 files changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c index fac54a3fa3f1..00ebf7af7467 100644 --- a/drivers/mtd/mtdcore.c +++ b/drivers/mtd/mtdcore.c @@ -65,8 +65,8 @@ static void mtd_release(struct device *dev) static int mtd_cls_suspend(struct device *dev, pm_message_t state) { struct mtd_info *mtd = dev_to_mtd(dev); - - if (mtd->suspend) + + if (mtd && mtd->suspend) return mtd->suspend(mtd); else return 0; @@ -76,7 +76,7 @@ static int mtd_cls_resume(struct device *dev) { struct mtd_info *mtd = dev_to_mtd(dev); - if (mtd->resume) + if (mtd && mtd->resume) mtd->resume(mtd); return 0; } @@ -298,6 +298,7 @@ int add_mtd_device(struct mtd_info *mtd) mtd->dev.class = &mtd_class; mtd->dev.devt = MTD_DEVT(i); dev_set_name(&mtd->dev, "mtd%d", i); + dev_set_drvdata(&mtd->dev, mtd); if (device_register(&mtd->dev) != 0) { mtd_table[i] = NULL; break; diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index 5675b63a0631..0f32a9b6ff55 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -251,7 +251,7 @@ struct mtd_info { static inline struct mtd_info *dev_to_mtd(struct device *dev) { - return dev ? container_of(dev, struct mtd_info, dev) : NULL; + return dev ? dev_get_drvdata(dev) : NULL; } static inline uint32_t mtd_div_by_eb(uint64_t sz, struct mtd_info *mtd) -- cgit v1.2.3 From 8022c13c27b822cf22f13df10b42aae89cd56bf0 Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Fri, 10 Jul 2009 17:02:17 +0300 Subject: mtd: blkdevs: do not forget to get MTD devices Nowadays MTD devices have to be "get" before they can be used. This has to be done with 'get_mtd_device()'. The 'blktrans_open()' function did not do this and instead used 'try_module_get()'. Fix this. Since 'get_mtd_device()' already gets the module, extra 'try_module_get()' is not needed. This fixes oops when one tries to use mtdblock on top of gluebi. Reported-by: Holger Brunck Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/mtd_blkdevs.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c index c3f62654b6df..7baba40c1ed2 100644 --- a/drivers/mtd/mtd_blkdevs.c +++ b/drivers/mtd/mtd_blkdevs.c @@ -144,7 +144,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) struct mtd_blktrans_ops *tr = dev->tr; int ret = -ENODEV; - if (!try_module_get(dev->mtd->owner)) + if (!get_mtd_device(NULL, dev->mtd->index)) goto out; if (!try_module_get(tr->owner)) @@ -158,7 +158,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) ret = 0; if (tr->open && (ret = tr->open(dev))) { dev->mtd->usecount--; - module_put(dev->mtd->owner); + put_mtd_device(dev->mtd); out_tr: module_put(tr->owner); } @@ -177,7 +177,7 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode) if (!ret) { dev->mtd->usecount--; - module_put(dev->mtd->owner); + put_mtd_device(dev->mtd); module_put(tr->owner); } -- cgit v1.2.3 From 00acf4a80779611a7ea77ff5b5ffab886ed5cc42 Mon Sep 17 00:00:00 2001 From: Mika Korhonen Date: Thu, 11 Jun 2009 14:05:07 +0300 Subject: mtd: OneNAND: fix incorrect bufferram offset Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and the real page size differs from mtd_info.writesize. Signed-off-by: Mika Korhonen Acked-by: Kyungmin Park Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/onenand/omap2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 38d656b9b2ee..6fac1f496d4a 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -266,7 +266,7 @@ static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area) if (ONENAND_CURRENT_BUFFERRAM(this)) { if (area == ONENAND_DATARAM) - return mtd->writesize; + return this->writesize; if (area == ONENAND_SPARERAM) return mtd->oobsize; } -- cgit v1.2.3 From 3cae1cc149c40c14424162496eb5a7c8db1cd4fb Mon Sep 17 00:00:00 2001 From: Mika Korhonen Date: Thu, 25 Jun 2009 15:32:19 +0300 Subject: mtd: OneNAND: OMAP2/3: free GPMC CS on module removal GPMC CS was not freed in omap2_onenand_remove() preventing the module from reloading after removal. Signed-off-by: Mika Korhonen Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/onenand/omap2.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 6fac1f496d4a..0108ed42e877 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -770,6 +770,7 @@ static int __devexit omap2_onenand_remove(struct platform_device *pdev) } iounmap(c->onenand.base); release_mem_region(c->phys_base, ONENAND_IO_SIZE); + gpmc_cs_free(c->gpmc_cs); kfree(c); return 0; -- cgit v1.2.3 From 2bf961b7ccd69e108ac435c67e2b0522b403c578 Mon Sep 17 00:00:00 2001 From: Subrata Modak Date: Wed, 1 Jul 2009 19:22:47 +0530 Subject: mtd: remove 'SBC8240 Wind River' Device Driver Code This driver is causing build errors and is no longer needed -- it is obsoleted by physmap_of. Signed-off-by: Subrata Modak Tested-on-PPC64-by: Subrata Modak Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/maps/Kconfig | 7 -- drivers/mtd/maps/Makefile | 1 - drivers/mtd/maps/sbc8240.c | 250 --------------------------------------------- 3 files changed, 258 deletions(-) (limited to 'drivers') diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig index 0b98654d8eed..7a58bd5522fd 100644 --- a/drivers/mtd/maps/Kconfig +++ b/drivers/mtd/maps/Kconfig @@ -284,13 +284,6 @@ config MTD_L440GX BE VERY CAREFUL. -config MTD_SBC8240 - tristate "Flash device on SBC8240" - depends on MTD_JEDECPROBE && 8260 - help - Flash access on the SBC8240 board from Wind River. See - - config MTD_TQM8XXL tristate "CFI Flash device mapped on TQM8XXL" depends on MTD_CFI && TQM8xxL diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile index 8bae7f9850c0..5beb0662d724 100644 --- a/drivers/mtd/maps/Makefile +++ b/drivers/mtd/maps/Makefile @@ -50,7 +50,6 @@ obj-$(CONFIG_MTD_UCLINUX) += uclinux.o obj-$(CONFIG_MTD_NETtel) += nettel.o obj-$(CONFIG_MTD_SCB2_FLASH) += scb2_flash.o obj-$(CONFIG_MTD_H720X) += h720x-flash.o -obj-$(CONFIG_MTD_SBC8240) += sbc8240.o obj-$(CONFIG_MTD_IXP4XX) += ixp4xx.o obj-$(CONFIG_MTD_IXP2000) += ixp2000.o obj-$(CONFIG_MTD_WRSBC8260) += wr_sbc82xx_flash.o diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c index d5374cdcb163..e69de29bb2d1 100644 --- a/drivers/mtd/maps/sbc8240.c +++ b/drivers/mtd/maps/sbc8240.c @@ -1,250 +0,0 @@ -/* - * Handle mapping of the flash memory access routines on the SBC8240 board. - * - * Carolyn Smith, Tektronix, Inc. - * - * This code is GPLed - */ - -/* - * The SBC8240 has 2 flash banks. - * Bank 0 is a 512 KiB AMD AM29F040B; 8 x 64 KiB sectors. - * It contains the U-Boot code (7 sectors) and the environment (1 sector). - * Bank 1 is 4 x 1 MiB AMD AM29LV800BT; 15 x 64 KiB sectors, 1 x 32 KiB sector, - * 2 x 8 KiB sectors, 1 x 16 KiB sectors. - * Both parts are JEDEC compatible. - */ - -#include -#include -#include -#include - -#include -#include -#include - -#ifdef CONFIG_MTD_PARTITIONS -#include -#endif - -#define DEBUG - -#ifdef DEBUG -# define debugk(fmt,args...) printk(fmt ,##args) -#else -# define debugk(fmt,args...) -#endif - - -#define WINDOW_ADDR0 0xFFF00000 /* 512 KiB */ -#define WINDOW_SIZE0 0x00080000 -#define BUSWIDTH0 1 - -#define WINDOW_ADDR1 0xFF000000 /* 4 MiB */ -#define WINDOW_SIZE1 0x00400000 -#define BUSWIDTH1 8 - -#define MSG_PREFIX "sbc8240:" /* prefix for our printk()'s */ -#define MTDID "sbc8240-%d" /* for mtdparts= partitioning */ - - -static struct map_info sbc8240_map[2] = { - { - .name = "sbc8240 Flash Bank #0", - .size = WINDOW_SIZE0, - .bankwidth = BUSWIDTH0, - }, - { - .name = "sbc8240 Flash Bank #1", - .size = WINDOW_SIZE1, - .bankwidth = BUSWIDTH1, - } -}; - -#define NUM_FLASH_BANKS ARRAY_SIZE(sbc8240_map) - -/* - * The following defines the partition layout of SBC8240 boards. - * - * See include/linux/mtd/partitions.h for definition of the - * mtd_partition structure. - * - * The *_max_flash_size is the maximum possible mapped flash size - * which is not necessarily the actual flash size. It must correspond - * to the value specified in the mapping definition defined by the - * "struct map_desc *_io_desc" for the corresponding machine. - */ - -#ifdef CONFIG_MTD_PARTITIONS - -static struct mtd_partition sbc8240_uboot_partitions [] = { - /* Bank 0 */ - { - .name = "U-boot", /* U-Boot Firmware */ - .offset = 0, - .size = 0x00070000, /* 7 x 64 KiB sectors */ - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "environment", /* U-Boot environment */ - .offset = 0x00070000, - .size = 0x00010000, /* 1 x 64 KiB sector */ - }, -}; - -static struct mtd_partition sbc8240_fs_partitions [] = { - { - .name = "jffs", /* JFFS filesystem */ - .offset = 0, - .size = 0x003C0000, /* 4 * 15 * 64KiB */ - }, - { - .name = "tmp32", - .offset = 0x003C0000, - .size = 0x00020000, /* 4 * 32KiB */ - }, - { - .name = "tmp8a", - .offset = 0x003E0000, - .size = 0x00008000, /* 4 * 8KiB */ - }, - { - .name = "tmp8b", - .offset = 0x003E8000, - .size = 0x00008000, /* 4 * 8KiB */ - }, - { - .name = "tmp16", - .offset = 0x003F0000, - .size = 0x00010000, /* 4 * 16KiB */ - } -}; - -/* trivial struct to describe partition information */ -struct mtd_part_def -{ - int nums; - unsigned char *type; - struct mtd_partition* mtd_part; -}; - -static struct mtd_info *sbc8240_mtd[NUM_FLASH_BANKS]; -static struct mtd_part_def sbc8240_part_banks[NUM_FLASH_BANKS]; - - -#endif /* CONFIG_MTD_PARTITIONS */ - - -static int __init init_sbc8240_mtd (void) -{ - static struct _cjs { - u_long addr; - u_long size; - } pt[NUM_FLASH_BANKS] = { - { - .addr = WINDOW_ADDR0, - .size = WINDOW_SIZE0 - }, - { - .addr = WINDOW_ADDR1, - .size = WINDOW_SIZE1 - }, - }; - - int devicesfound = 0; - int i,j; - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - printk (KERN_NOTICE MSG_PREFIX - "Probing 0x%08lx at 0x%08lx\n", pt[i].size, pt[i].addr); - - sbc8240_map[i].map_priv_1 = - (unsigned long) ioremap (pt[i].addr, pt[i].size); - if (!sbc8240_map[i].map_priv_1) { - printk (MSG_PREFIX "failed to ioremap\n"); - for (j = 0; j < i; j++) { - iounmap((void *) sbc8240_map[j].map_priv_1); - sbc8240_map[j].map_priv_1 = 0; - } - return -EIO; - } - simple_map_init(&sbc8240_mtd[i]); - - sbc8240_mtd[i] = do_map_probe("jedec_probe", &sbc8240_map[i]); - - if (sbc8240_mtd[i]) { - sbc8240_mtd[i]->module = THIS_MODULE; - devicesfound++; - } else { - if (sbc8240_map[i].map_priv_1) { - iounmap((void *) sbc8240_map[i].map_priv_1); - sbc8240_map[i].map_priv_1 = 0; - } - } - } - - if (!devicesfound) { - printk(KERN_NOTICE MSG_PREFIX - "No suppported flash chips found!\n"); - return -ENXIO; - } - -#ifdef CONFIG_MTD_PARTITIONS - sbc8240_part_banks[0].mtd_part = sbc8240_uboot_partitions; - sbc8240_part_banks[0].type = "static image"; - sbc8240_part_banks[0].nums = ARRAY_SIZE(sbc8240_uboot_partitions); - sbc8240_part_banks[1].mtd_part = sbc8240_fs_partitions; - sbc8240_part_banks[1].type = "static file system"; - sbc8240_part_banks[1].nums = ARRAY_SIZE(sbc8240_fs_partitions); - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - - if (!sbc8240_mtd[i]) continue; - if (sbc8240_part_banks[i].nums == 0) { - printk (KERN_NOTICE MSG_PREFIX - "No partition info available, registering whole device\n"); - add_mtd_device(sbc8240_mtd[i]); - } else { - printk (KERN_NOTICE MSG_PREFIX - "Using %s partition definition\n", sbc8240_part_banks[i].mtd_part->name); - add_mtd_partitions (sbc8240_mtd[i], - sbc8240_part_banks[i].mtd_part, - sbc8240_part_banks[i].nums); - } - } -#else - printk(KERN_NOTICE MSG_PREFIX - "Registering %d flash banks at once\n", devicesfound); - - for (i = 0; i < devicesfound; i++) { - add_mtd_device(sbc8240_mtd[i]); - } -#endif /* CONFIG_MTD_PARTITIONS */ - - return devicesfound == 0 ? -ENXIO : 0; -} - -static void __exit cleanup_sbc8240_mtd (void) -{ - int i; - - for (i = 0; i < NUM_FLASH_BANKS; i++) { - if (sbc8240_mtd[i]) { - del_mtd_device (sbc8240_mtd[i]); - map_destroy (sbc8240_mtd[i]); - } - if (sbc8240_map[i].map_priv_1) { - iounmap ((void *) sbc8240_map[i].map_priv_1); - sbc8240_map[i].map_priv_1 = 0; - } - } -} - -module_init (init_sbc8240_mtd); -module_exit (cleanup_sbc8240_mtd); - -MODULE_LICENSE ("GPL"); -MODULE_AUTHOR ("Carolyn Smith "); -MODULE_DESCRIPTION ("MTD map driver for SBC8240 boards"); - -- cgit v1.2.3 From d676c11727815761e41a81b00c054b4bec452ae5 Mon Sep 17 00:00:00 2001 From: Matthias Kaehlcke Date: Tue, 14 Jul 2009 22:04:29 +0200 Subject: mtd: mtdblock: introduce mtdblks_lock The mtdblks array and its content are prone to race conditions. Introduce the mutex mtdblks_lock in order to solve this. [Amended by Artem Bityutskiy] Signed-off-by: Matthias Kaehlcke Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/mtdblock.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c index 208c6faa0358..77db5ce24d92 100644 --- a/drivers/mtd/mtdblock.c +++ b/drivers/mtd/mtdblock.c @@ -29,6 +29,8 @@ static struct mtdblk_dev { enum { STATE_EMPTY, STATE_CLEAN, STATE_DIRTY } cache_state; } *mtdblks[MAX_MTD_DEVICES]; +static struct mutex mtdblks_lock; + /* * Cache stuff... * @@ -270,15 +272,19 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd) DEBUG(MTD_DEBUG_LEVEL1,"mtdblock_open\n"); + mutex_lock(&mtdblks_lock); if (mtdblks[dev]) { mtdblks[dev]->count++; + mutex_unlock(&mtdblks_lock); return 0; } /* OK, it's not open. Create cache info for it */ mtdblk = kzalloc(sizeof(struct mtdblk_dev), GFP_KERNEL); - if (!mtdblk) + if (!mtdblk) { + mutex_unlock(&mtdblks_lock); return -ENOMEM; + } mtdblk->count = 1; mtdblk->mtd = mtd; @@ -291,6 +297,7 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd) } mtdblks[dev] = mtdblk; + mutex_unlock(&mtdblks_lock); DEBUG(MTD_DEBUG_LEVEL1, "ok\n"); @@ -304,6 +311,8 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd) DEBUG(MTD_DEBUG_LEVEL1, "mtdblock_release\n"); + mutex_lock(&mtdblks_lock); + mutex_lock(&mtdblk->cache_mutex); write_cached_data(mtdblk); mutex_unlock(&mtdblk->cache_mutex); @@ -316,6 +325,9 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd) vfree(mtdblk->cache_data); kfree(mtdblk); } + + mutex_unlock(&mtdblks_lock); + DEBUG(MTD_DEBUG_LEVEL1, "ok\n"); return 0; @@ -376,6 +388,8 @@ static struct mtd_blktrans_ops mtdblock_tr = { static int __init init_mtdblock(void) { + mutex_init(&mtdblks_lock); + return register_mtd_blktrans(&mtdblock_tr); } -- cgit v1.2.3 From 126b67b8d26f6623d199aa59279f2e3243f2144c Mon Sep 17 00:00:00 2001 From: Doug Thompson Date: Mon, 3 Aug 2009 12:37:06 +0200 Subject: amd64_edac: fix ECC checking On the good path of BIOS enabled ECC and no override, the value returned is 1 by omission and thus is deemed failing by the probe-function. Allow proper module initialization by clearing the retval explicitly. Signed-off-by: Doug Thompson Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 24964c1d0af9..5fa924d61b10 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -2977,6 +2977,9 @@ static int amd64_check_ecc_enabled(struct amd64_pvt *pvt) "ECC is enabled by BIOS, Proceeding " "with EDAC module initialization\n"); + /* Signal good ECC status */ + ret = 0; + /* CLEAR the override, since BIOS controlled it */ ecc_enable_override = 0; } -- cgit v1.2.3 From 202ff1ec8e53d5dd36e1a5bd4b0a7ed7dbd45087 Mon Sep 17 00:00:00 2001 From: Mallikarjuna R Chilakala Date: Mon, 3 Aug 2009 07:20:38 +0000 Subject: ixgbe: Patch to modify 82598 PCIe completion timeout values The default completion timeout values for 82598 should be in the range of 50us to 50ms, however the hardware default for these parts is 500us to 1ms which is less than the 10ms recommended by the pcie spec. To address this we need to increase the value to either 10ms to 250ms for capability version 1 configuration, or 16ms to 55ms for version 2. Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_82598.c | 67 ++++++++++++++++++++++++++++++++++++++++- drivers/net/ixgbe/ixgbe_type.h | 8 +++++ 2 files changed, 74 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index b9923047ce11..522c03bc1dad 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -49,6 +49,51 @@ static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset, u8 *eeprom_data); +/** + * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout + * @hw: pointer to the HW structure + * + * The defaults for 82598 should be in the range of 50us to 50ms, + * however the hardware default for these parts is 500us to 1ms which is less + * than the 10ms recommended by the pci-e spec. To address this we need to + * increase the value to either 10ms to 250ms for capability version 1 config, + * or 16ms to 55ms for version 2. + **/ +void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw) +{ + struct ixgbe_adapter *adapter = hw->back; + u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR); + u16 pcie_devctl2; + + /* only take action if timeout value is defaulted to 0 */ + if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK) + goto out; + + /* + * if capababilities version is type 1 we can write the + * timeout of 10ms to 250ms through the GCR register + */ + if (!(gcr & IXGBE_GCR_CAP_VER2)) { + gcr |= IXGBE_GCR_CMPL_TMOUT_10ms; + goto out; + } + + /* + * for version 2 capabilities we need to write the config space + * directly in order to set the completion timeout value for + * 16ms to 55ms + */ + pci_read_config_word(adapter->pdev, + IXGBE_PCI_DEVICE_CONTROL2, &pcie_devctl2); + pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms; + pci_write_config_word(adapter->pdev, + IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2); +out: + /* disable completion timeout resend */ + gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND; + IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr); +} + /** * ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count * @hw: pointer to hardware structure @@ -152,6 +197,26 @@ out: return ret_val; } +/** + * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx + * @hw: pointer to hardware structure + * + * Starts the hardware using the generic start_hw function. + * Then set pcie completion timeout + **/ +s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw) +{ + s32 ret_val = 0; + + ret_val = ixgbe_start_hw_generic(hw); + + /* set the completion timeout for interface */ + if (ret_val == 0) + ixgbe_set_pcie_completion_timeout(hw); + + return ret_val; +} + /** * ixgbe_get_link_capabilities_82598 - Determines link capabilities * @hw: pointer to hardware structure @@ -1085,7 +1150,7 @@ out: static struct ixgbe_mac_operations mac_ops_82598 = { .init_hw = &ixgbe_init_hw_generic, .reset_hw = &ixgbe_reset_hw_82598, - .start_hw = &ixgbe_start_hw_generic, + .start_hw = &ixgbe_start_hw_82598, .clear_hw_cntrs = &ixgbe_clear_hw_cntrs_generic, .get_media_type = &ixgbe_get_media_type_82598, .get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82598, diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index fa87309dc087..be90eb4575f6 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -718,6 +718,12 @@ #define IXGBE_ECC_STATUS_82599 0x110E0 #define IXGBE_BAR_CTRL_82599 0x110F4 +/* PCI Express Control */ +#define IXGBE_GCR_CMPL_TMOUT_MASK 0x0000F000 +#define IXGBE_GCR_CMPL_TMOUT_10ms 0x00001000 +#define IXGBE_GCR_CMPL_TMOUT_RESEND 0x00010000 +#define IXGBE_GCR_CAP_VER2 0x00040000 + /* Time Sync Registers */ #define IXGBE_TSYNCRXCTL 0x05188 /* Rx Time Sync Control register - RW */ #define IXGBE_TSYNCTXCTL 0x08C00 /* Tx Time Sync Control register - RW */ @@ -1521,6 +1527,7 @@ /* PCI Bus Info */ #define IXGBE_PCI_LINK_STATUS 0xB2 +#define IXGBE_PCI_DEVICE_CONTROL2 0xC8 #define IXGBE_PCI_LINK_WIDTH 0x3F0 #define IXGBE_PCI_LINK_WIDTH_1 0x10 #define IXGBE_PCI_LINK_WIDTH_2 0x20 @@ -1531,6 +1538,7 @@ #define IXGBE_PCI_LINK_SPEED_5000 0x2 #define IXGBE_PCI_HEADER_TYPE_REGISTER 0x0E #define IXGBE_PCI_HEADER_TYPE_MULTIFUNC 0x80 +#define IXGBE_PCI_DEVICE_CONTROL2_16ms 0x0005 /* Number of 100 microseconds we wait for PCI Express master disable */ #define IXGBE_PCI_MASTER_DISABLE_TIMEOUT 800 -- cgit v1.2.3 From 371842448c05b42d11a4be1c8e4e81d62ecc7534 Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 30 Jul 2009 17:43:48 -0700 Subject: cfg80211: fix regression on beacon world roaming feature A regression was added through patch a4ed90d6: "cfg80211: respect API on orig_flags on channel for beacon hint" We did indeed respect _orig flags but the intention was not clearly stated in the commit log. This patch fixes firmware issues picked up by iwlwifi when we lift passive scan of beaconing restrictions on channels its EEPROM has been configured to always enable. By doing so though we also disallowed beacon hints on devices registering their wiphy with custom world regulatory domains enabled, this happens to be currently ath5k, ath9k and ar9170. The passive scan and beacon restrictions on those devices would never be lifted even if we did find a beacon and the hardware did support such enhancements when world roaming. Since Johannes indicates iwlwifi firmware cannot be changed to allow beacon hinting we set up a flag now to specifically allow drivers to disable beacon hints for devices which cannot use them. We enable the flag on iwlwifi to disable beacon hints and by default enable it for all other drivers. It should be noted beacon hints lift passive scan flags and beacon restrictions when we receive a beacon from an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz band. We don't bother with channels 1-11 as those channels are allowed world wide. This should fix world roaming for ath5k, ath9k and ar9170, thereby improving scan time when we receive the first beacon from any AP, and also enabling beaconing operation (AP/IBSS/Mesh) on cards which would otherwise not be allowed to do so. Drivers not using custom regulatory stuff (wiphy_apply_custom_regulatory()) were not affected by this as the orig_flags for the channels would have been cleared upon wiphy registration. I tested this with a world roaming ath5k card. Cc: Jouni Malinen Signed-off-by: Luis R. Rodriguez Reviewed-by: Johannes Berg Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-core.c | 3 +++ drivers/net/wireless/iwlwifi/iwl3945-base.c | 3 +++ include/net/cfg80211.h | 5 +++++ net/wireless/reg.c | 9 +++++---- net/wireless/reg.h | 3 ++- 5 files changed, 18 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index 6ab07165ea28..18b135f510e5 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -1332,6 +1332,9 @@ int iwl_setup_mac(struct iwl_priv *priv) hw->wiphy->custom_regulatory = true; + /* Firmware does not support this */ + hw->wiphy->disable_beacon_hints = true; + hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX; /* we create the 802.11 header and a zero-length SSID element */ hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2; diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 2f50ab60bfdf..523843369ca2 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -3968,6 +3968,9 @@ static int iwl3945_setup_mac(struct iwl_priv *priv) hw->wiphy->custom_regulatory = true; + /* Firmware does not support this */ + hw->wiphy->disable_beacon_hints = true; + hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX_3945; /* we create the 802.11 header and a zero-length SSID element */ hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2; diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 1a21895b732b..d1892d66701a 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -979,6 +979,10 @@ struct cfg80211_ops { * channels at a later time. This can be used for devices which do not * have calibration information gauranteed for frequencies or settings * outside of its regulatory domain. + * @disable_beacon_hints: enable this if your driver needs to ensure that + * passive scan flags and beaconing flags may not be lifted by cfg80211 + * due to regulatory beacon hints. For more information on beacon + * hints read the documenation for regulatory_hint_found_beacon() * @reg_notifier: the driver's regulatory notification callback * @regd: the driver's regulatory domain, if one was requested via * the regulatory_hint() API. This can be used by the driver @@ -1004,6 +1008,7 @@ struct wiphy { bool custom_regulatory; bool strict_regulatory; + bool disable_beacon_hints; enum cfg80211_signal_type signal_type; diff --git a/net/wireless/reg.c b/net/wireless/reg.c index 5e14371cda70..75a406d33619 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -1089,17 +1089,18 @@ static void handle_reg_beacon(struct wiphy *wiphy, chan->beacon_found = true; + if (wiphy->disable_beacon_hints) + return; + chan_before.center_freq = chan->center_freq; chan_before.flags = chan->flags; - if ((chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) && - !(chan->orig_flags & IEEE80211_CHAN_PASSIVE_SCAN)) { + if (chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) { chan->flags &= ~IEEE80211_CHAN_PASSIVE_SCAN; channel_changed = true; } - if ((chan->flags & IEEE80211_CHAN_NO_IBSS) && - !(chan->orig_flags & IEEE80211_CHAN_NO_IBSS)) { + if (chan->flags & IEEE80211_CHAN_NO_IBSS) { chan->flags &= ~IEEE80211_CHAN_NO_IBSS; channel_changed = true; } diff --git a/net/wireless/reg.h b/net/wireless/reg.h index e37829a49dc4..4e167a8e11be 100644 --- a/net/wireless/reg.h +++ b/net/wireless/reg.h @@ -30,7 +30,8 @@ int set_regdom(const struct ieee80211_regdomain *rd); * non-radar 5 GHz channels. * * Drivers do not need to call this, cfg80211 will do it for after a scan - * on a newly found BSS. + * on a newly found BSS. If you cannot make use of this feature you can + * set the wiphy->disable_beacon_hints to true. */ int regulatory_hint_found_beacon(struct wiphy *wiphy, struct ieee80211_channel *beacon_chan, -- cgit v1.2.3 From dbc1eec485625228895ded6baf6bd01ce2475410 Mon Sep 17 00:00:00 2001 From: Patrick Simmons Date: Sun, 2 Aug 2009 02:46:28 -0600 Subject: zd1211rw: fix unaligned access in zd_mac_rx Fix an unaligned memory access in the zd_mac_rx function of zd1211rw that causes problems on SPARC64. Signed-off-by: Patrick Simmons Signed-off-by: John W. Linville --- drivers/net/wireless/zd1211rw/zd_mac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c index 40b07b988224..3bd3c779fff3 100644 --- a/drivers/net/wireless/zd1211rw/zd_mac.c +++ b/drivers/net/wireless/zd1211rw/zd_mac.c @@ -698,7 +698,7 @@ int zd_mac_rx(struct ieee80211_hw *hw, const u8 *buffer, unsigned int length) && !mac->pass_ctrl) return 0; - fc = *(__le16 *)buffer; + fc = get_unaligned((__le16*)buffer); need_padding = ieee80211_is_data_qos(fc) ^ ieee80211_has_a4(fc); skb = dev_alloc_skb(length + (need_padding ? 2 : 0)); -- cgit v1.2.3 From c37457e69ffd7d3c94cbfcc1c39be9a45dd7ad21 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 3 Aug 2009 11:11:45 +0200 Subject: drivers/net/wireless/iwlwifi: introduce missing kfree Move orthogonal error handling code up before a kzalloc, so that it doesn't have to free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // Signed-off-by: Julia Lawall Acked-by: Zhu Yi Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-debugfs.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-debugfs.c b/drivers/net/wireless/iwlwifi/iwl-debugfs.c index 11e08c068917..ca00cc8ad4c7 100644 --- a/drivers/net/wireless/iwlwifi/iwl-debugfs.c +++ b/drivers/net/wireless/iwlwifi/iwl-debugfs.c @@ -308,18 +308,18 @@ static ssize_t iwl_dbgfs_nvm_read(struct file *file, return -ENODATA; } + ptr = priv->eeprom; + if (!ptr) { + IWL_ERR(priv, "Invalid EEPROM/OTP memory\n"); + return -ENOMEM; + } + /* 4 characters for byte 0xYY */ buf = kzalloc(buf_size, GFP_KERNEL); if (!buf) { IWL_ERR(priv, "Can not allocate Buffer\n"); return -ENOMEM; } - - ptr = priv->eeprom; - if (!ptr) { - IWL_ERR(priv, "Invalid EEPROM/OTP memory\n"); - return -ENOMEM; - } pos += scnprintf(buf + pos, buf_size - pos, "NVM Type: %s\n", (priv->nvm_device_type == NVM_DEVICE_TYPE_OTP) ? "OTP" : "EEPROM"); -- cgit v1.2.3 From 9f9857bb5e147b977b9878c46e3dd87c9e8caf50 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 1 Aug 2009 10:55:53 +0200 Subject: drivers/net/wireless: introduce missing kfree Error handling code following a kzalloc should free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // Signed-off-by: Julia Lawall Signed-off-by: John W. Linville --- drivers/net/wireless/iwmc3200wifi/commands.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/wireless/iwmc3200wifi/commands.c b/drivers/net/wireless/iwmc3200wifi/commands.c index 834a7f544e5d..e2334d123599 100644 --- a/drivers/net/wireless/iwmc3200wifi/commands.c +++ b/drivers/net/wireless/iwmc3200wifi/commands.c @@ -220,6 +220,7 @@ int iwm_store_rxiq_calib_result(struct iwm_priv *iwm) eeprom_rxiq = iwm_eeprom_access(iwm, IWM_EEPROM_CALIB_RXIQ); if (IS_ERR(eeprom_rxiq)) { IWM_ERR(iwm, "Couldn't access EEPROM RX IQ entry\n"); + kfree(rxiq); return PTR_ERR(eeprom_rxiq); } -- cgit v1.2.3 From b929c633b4067be18a335d278a66fd5deef3cabe Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 2 Aug 2009 09:44:12 +0200 Subject: libertas: Read buffer overflow Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/11d.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/11d.c b/drivers/net/wireless/libertas/11d.c index 9a5408e7d94a..5c6968101f0d 100644 --- a/drivers/net/wireless/libertas/11d.c +++ b/drivers/net/wireless/libertas/11d.c @@ -47,7 +47,7 @@ static u8 lbs_region_2_code(u8 *region) { u8 i; - for (i = 0; region[i] && i < COUNTRY_CODE_LEN; i++) + for (i = 0; i < COUNTRY_CODE_LEN && region[i]; i++) region[i] = toupper(region[i]); for (i = 0; i < ARRAY_SIZE(region_code_mapping); i++) { -- cgit v1.2.3 From 99f1b01562b7dcae75b043114f76163fbf84fcab Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Mon, 3 Aug 2009 12:10:16 -0700 Subject: iwlagn: do not send key clear commands when rfkill enabled Do all key clearing except sending sommands to device when rfkill enabled. When rfkill enabled the interface is brought down and will be brought back up correctly after rfkill is enabled again. Same change is not needed for iwl3945 as it ignores return code when sending key clearing command to device. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13742 Signed-off-by: Reinette Chatre Tested-by: Frans Pop Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-sta.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c index 2addf735b193..ffd5c61a7553 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.c +++ b/drivers/net/wireless/iwlwifi/iwl-sta.c @@ -566,6 +566,8 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv, unsigned long flags; spin_lock_irqsave(&priv->sta_lock, flags); + IWL_DEBUG_WEP(priv, "Removing default WEP key: idx=%d\n", + keyconf->keyidx); if (!test_and_clear_bit(keyconf->keyidx, &priv->ucode_key_table)) IWL_ERR(priv, "index %d not used in uCode key table.\n", @@ -573,6 +575,11 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv, priv->default_wep_key--; memset(&priv->wep_keys[keyconf->keyidx], 0, sizeof(priv->wep_keys[0])); + if (iwl_is_rfkill(priv)) { + IWL_DEBUG_WEP(priv, "Not sending REPLY_WEPKEY command due to RFKILL.\n"); + spin_unlock_irqrestore(&priv->sta_lock, flags); + return 0; + } ret = iwl_send_static_wepkey_cmd(priv, 1); IWL_DEBUG_WEP(priv, "Remove default WEP key: idx=%d ret=%d\n", keyconf->keyidx, ret); @@ -853,6 +860,11 @@ int iwl_remove_dynamic_key(struct iwl_priv *priv, priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; + if (iwl_is_rfkill(priv)) { + IWL_DEBUG_WEP(priv, "Not sending REPLY_ADD_STA command because RFKILL enabled. \n"); + spin_unlock_irqrestore(&priv->sta_lock, flags); + return 0; + } ret = iwl_send_add_sta(priv, &priv->stations[sta_id].sta, CMD_ASYNC); spin_unlock_irqrestore(&priv->sta_lock, flags); return ret; -- cgit v1.2.3 From f6caa14aa0b126d4a2933907d1519611b2a8524a Mon Sep 17 00:00:00 2001 From: Mike McCormack Date: Fri, 31 Jul 2009 01:57:42 +0000 Subject: sky2: Avoid transmits during sky2_down() This patch supersedes my previous patch "sky2: Avoid transmitting during sky2_restart". I have reworked the patch to avoid crashes during both sky2_restart() and sky2_set_ringparam(). Without this patch, the sky2 driver can be crashed by doing: # pktgen eth1 & (transmit many packets on eth1) # ethtool -G eth1 tx 510 I am aware you object to storing extra state, but I can't see a way around this. Without remembering that we're restarting, netif_wake_queue() is called in the ISR from sky2_tx_complete(), and netif_tx_lock() is used in sky2_tx_done(). If anybody can see a way around this, please let me know. Signed-off-by: Mike McCormack Signed-off-by: David S. Miller --- drivers/net/sky2.c | 14 +++++++++++++- drivers/net/sky2.h | 1 + 2 files changed, 14 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 3550c5dcd93c..0a551d8f5d95 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -1488,6 +1488,8 @@ static int sky2_up(struct net_device *dev) sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL); #endif + sky2->restarting = 0; + err = sky2_rx_start(sky2); if (err) goto err_out; @@ -1500,6 +1502,9 @@ static int sky2_up(struct net_device *dev) sky2_set_multicast(dev); + /* wake queue incase we are restarting */ + netif_wake_queue(dev); + if (netif_msg_ifup(sky2)) printk(KERN_INFO PFX "%s: enabling interface\n", dev->name); return 0; @@ -1533,6 +1538,8 @@ static inline int tx_dist(unsigned tail, unsigned head) /* Number of list elements available for next tx */ static inline int tx_avail(const struct sky2_port *sky2) { + if (unlikely(sky2->restarting)) + return 0; return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod); } @@ -1818,6 +1825,10 @@ static int sky2_down(struct net_device *dev) if (netif_msg_ifdown(sky2)) printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); + /* explicitly shut off tx incase we're restarting */ + sky2->restarting = 1; + netif_tx_disable(dev); + /* Force flow control off */ sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); @@ -2359,7 +2370,7 @@ static inline void sky2_tx_done(struct net_device *dev, u16 last) { struct sky2_port *sky2 = netdev_priv(dev); - if (netif_running(dev)) { + if (likely(netif_running(dev) && !sky2->restarting)) { netif_tx_lock(dev); sky2_tx_complete(sky2, last); netif_tx_unlock(dev); @@ -4283,6 +4294,7 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, spin_lock_init(&sky2->phy_lock); sky2->tx_pending = TX_DEF_PENDING; sky2->rx_pending = RX_DEF_PENDING; + sky2->restarting = 0; hw->dev[port] = dev; diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index b5549c9e5107..4486b066b43f 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2051,6 +2051,7 @@ struct sky2_port { u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */ u8 rx_csum; u8 wol; + u8 restarting; enum flow_control flow_mode; enum flow_control flow_status; -- cgit v1.2.3 From 7781de74568bddfefbd2d32a934a8c791a2420cd Mon Sep 17 00:00:00 2001 From: Jakob Bornecrantz Date: Mon, 3 Aug 2009 13:43:58 +0100 Subject: drm: Small logic fix in drm_mode_setcrtc Match the logic to the comments in the debug message Signed-off-by: Jakob Bornecrantz Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 8fab7890a363..33be210d6723 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -1461,7 +1461,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, goto out; } - if (crtc_req->count_connectors > 0 && !mode && !fb) { + if (crtc_req->count_connectors > 0 && (!mode || !fb)) { DRM_DEBUG("Count connectors is %d but no mode or fb set\n", crtc_req->count_connectors); ret = -EINVAL; -- cgit v1.2.3 From 4cb72b1727140f131b2df5f37c2e54f5965f98c2 Mon Sep 17 00:00:00 2001 From: Jakob Bornecrantz Date: Mon, 3 Aug 2009 13:43:59 +0100 Subject: drm: Catch stop possible NULL pointer reference This was caught by Weiss. Also added some comments to the fb_changed and mode_changed variables to explain what they do. Signed-off-by: Jakob Bornecrantz Tested-by: Thomas White Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc_helper.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_crtc_helper.c b/drivers/gpu/drm/drm_crtc_helper.c index 3da9cfa31848..6aaa2cb23365 100644 --- a/drivers/gpu/drm/drm_crtc_helper.c +++ b/drivers/gpu/drm/drm_crtc_helper.c @@ -706,8 +706,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set) struct drm_encoder **save_encoders, *new_encoder; struct drm_framebuffer *old_fb = NULL; bool save_enabled; - bool mode_changed = false; - bool fb_changed = false; + bool mode_changed = false; /* if true do a full mode set */ + bool fb_changed = false; /* if true and !mode_changed just do a flip */ struct drm_connector *connector; int count = 0, ro, fail = 0; struct drm_crtc_helper_funcs *crtc_funcs; @@ -758,6 +758,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set) if (set->crtc->fb == NULL) { DRM_DEBUG("crtc has no fb, full mode set\n"); mode_changed = true; + } else if (set->fb == NULL) { + mode_changed = true; } else if ((set->fb->bits_per_pixel != set->crtc->fb->bits_per_pixel) || set->fb->depth != set->crtc->fb->depth) -- cgit v1.2.3 From 0924d942256ac470c5f7b4ebaf7fe0415fc6fa59 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 3 Aug 2009 12:03:03 +1000 Subject: drm/radeon/kms: fix rv515 VRAM initialisation. This got missed in the VRAM init re-workings. Signed-of-by: Dave Airlie --- drivers/gpu/drm/radeon/rv515.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index 551e608702e4..fd8f3ca716ea 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -370,6 +370,7 @@ void rv515_vram_info(struct radeon_device *rdev) rv515_vram_get_type(rdev); + r100_vram_init_sizes(rdev); /* FIXME: we should enforce default clock in case GPU is not in * default setup */ -- cgit v1.2.3 From 6d0897ba58139523d37e97855ee0fe2d78629da6 Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Fri, 31 Jul 2009 10:47:51 +0200 Subject: drm/ttm: Fix a potential comparison of structs. On some architectures the comparison may cause a compilation failure. Original partial fix Signed-off-by: Thomas Hellstrom Signed-off-by: Pekka Paalanen Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo_util.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c index ce2e6f38ea01..ad4ada07c6cf 100644 --- a/drivers/gpu/drm/ttm/ttm_bo_util.c +++ b/drivers/gpu/drm/ttm/ttm_bo_util.c @@ -150,7 +150,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, #ifdef CONFIG_X86 dst = kmap_atomic_prot(d, KM_USER0, prot); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) dst = vmap(&d, 1, 0, prot); else dst = kmap(d); @@ -163,7 +163,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src, #ifdef CONFIG_X86 kunmap_atomic(dst, KM_USER0); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) vunmap(dst); else kunmap(d); @@ -186,7 +186,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, #ifdef CONFIG_X86 src = kmap_atomic_prot(s, KM_USER0, prot); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) src = vmap(&s, 1, 0, prot); else src = kmap(s); @@ -199,7 +199,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst, #ifdef CONFIG_X86 kunmap_atomic(src, KM_USER0); #else - if (prot != PAGE_KERNEL) + if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL)) vunmap(src); else kunmap(s); -- cgit v1.2.3 From de05065ff5d6878523317ff4a0b48a1239f80f73 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 3 Aug 2009 12:05:34 +1000 Subject: drm/radeon/kms: fix nomodeset. The ordering was wrong to get the nomodeset parameter to work. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_drv.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c index 3cfcee17dc56..0bd5879a4957 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.c +++ b/drivers/gpu/drm/radeon/radeon_drv.c @@ -318,6 +318,14 @@ static int __init radeon_init(void) driver = &driver_old; driver->num_ioctls = radeon_max_ioctl; #if defined(CONFIG_DRM_RADEON_KMS) +#ifdef CONFIG_VGA_CONSOLE + if (vgacon_text_force() && radeon_modeset == -1) { + DRM_INFO("VGACON disable radeon kernel modesetting.\n"); + driver = &driver_old; + driver->driver_features &= ~DRIVER_MODESET; + radeon_modeset = 0; + } +#endif /* if enabled by default */ if (radeon_modeset == -1) { DRM_INFO("radeon default to kernel modesetting.\n"); @@ -329,17 +337,8 @@ static int __init radeon_init(void) driver->driver_features |= DRIVER_MODESET; driver->num_ioctls = radeon_max_kms_ioctl; } - /* if the vga console setting is enabled still * let modprobe override it */ -#ifdef CONFIG_VGA_CONSOLE - if (vgacon_text_force() && radeon_modeset == -1) { - DRM_INFO("VGACON disable radeon kernel modesetting.\n"); - driver = &driver_old; - driver->driver_features &= ~DRIVER_MODESET; - radeon_modeset = 0; - } -#endif #endif return drm_init(driver); } -- cgit v1.2.3 From c9b7fb54f0a51e587fa09be3a85666b43d36a850 Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Wed, 29 Jul 2009 21:28:24 +0800 Subject: drm/radeon/kms: fix memory leak in radeon_driver_load_kms This patch fixes following kmemleak report: unreferenced object 0xffff88022cb53000 (size 4096): comm "work_for_cpu", pid 97, jiffies 4294672345 backtrace: [] create_object+0x19f/0x2a0 [] kmemleak_alloc+0x26/0x4c [] __kmalloc+0x187/0x1b0 [] kzalloc.clone.0+0x13/0x15 [radeon] [] radeon_driver_load_kms+0x26/0xe1 [radeon] [] drm_get_dev+0x37f/0x480 [drm] [] radeon_pci_probe+0x15/0x269 [radeon] [] local_pci_probe+0x17/0x1b [] do_work_for_cpu+0x18/0x2a [] kthread+0x8a/0x92 [] child_rip+0xa/0x20 [] 0xffffffffffffffff Signed-off-by: Xiaotian Feng Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_kms.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 937a2f1cdb46..3357110e30ce 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -58,6 +58,8 @@ int radeon_driver_load_kms(struct drm_device *dev, unsigned long flags) if (r) { DRM_ERROR("Failed to initialize radeon, disabling IOCTL\n"); radeon_device_fini(rdev); + kfree(rdev); + dev->dev_private = NULL; return r; } return 0; -- cgit v1.2.3 From fee280d3fd9bc5247bef9f4ab35a4693bfffdcfd Mon Sep 17 00:00:00 2001 From: Thomas Hellstrom Date: Mon, 3 Aug 2009 12:39:06 +0200 Subject: drm/ttm: Fix a sync object leak. If there are multiple simultaneous waiters for the same buffer object, a temporary reference to its sync object may be leaked. Signed-off-by: Thomas Hellstrom Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index 6538d4236989..aa82d5370c38 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -1575,6 +1575,10 @@ int ttm_bo_wait(struct ttm_buffer_object *bo, driver->sync_obj_unref(&sync_obj); driver->sync_obj_unref(&tmp_obj); spin_lock(&bo->lock); + } else { + spin_unlock(&bo->lock); + driver->sync_obj_unref(&sync_obj); + spin_lock(&bo->lock); } } return 0; -- cgit v1.2.3 From fa99239cb73dbf419bea9f334b85ba94ac88a532 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 3 Aug 2009 14:20:32 +0200 Subject: drm/radeon: Read buffer overflow Check whether index is within bounds before grabbing the element. Signed-off-by: Roel Kluin Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index 05a44896dffb..f1ba8ff41130 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -722,13 +722,14 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p, unsigned idx) { struct radeon_cs_chunk *ib_chunk = &p->chunks[p->chunk_ib_idx]; - uint32_t header = ib_chunk->kdata[idx]; + uint32_t header; if (idx >= ib_chunk->length_dw) { DRM_ERROR("Can not parse packet at %d after CS end %d !\n", idx, ib_chunk->length_dw); return -EINVAL; } + header = ib_chunk->kdata[idx]; pkt->idx = idx; pkt->type = CP_PACKET_GET_TYPE(header); pkt->count = CP_PACKET_GET_COUNT(header); -- cgit v1.2.3 From c96e7c7a3a79931446ecf9494a8415e4d164ebd8 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 3 Aug 2009 14:22:53 +0200 Subject: drm/ttm: Read buffer overflow Check whether index is within bounds before grabbing the element. Signed-off-by: Roel Kluin Signed-off-by: Dave Airlie --- drivers/gpu/drm/ttm/ttm_bo.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c index aa82d5370c38..c2b0d710d10f 100644 --- a/drivers/gpu/drm/ttm/ttm_bo.c +++ b/drivers/gpu/drm/ttm/ttm_bo.c @@ -1182,13 +1182,14 @@ static int ttm_bo_force_list_clean(struct ttm_bo_device *bdev, int ttm_bo_clean_mm(struct ttm_bo_device *bdev, unsigned mem_type) { - struct ttm_mem_type_manager *man = &bdev->man[mem_type]; + struct ttm_mem_type_manager *man; int ret = -EINVAL; if (mem_type >= TTM_NUM_MEM_TYPES) { printk(KERN_ERR TTM_PFX "Illegal memory type %d\n", mem_type); return ret; } + man = &bdev->man[mem_type]; if (!man->has_type) { printk(KERN_ERR TTM_PFX "Trying to take down uninitialized " -- cgit v1.2.3 From 0cb13536c3382004bd9b833565e2af33f26ed1fb Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Mon, 3 Aug 2009 21:10:01 -0700 Subject: 3c59x: Fix build failure with gcc 3.2 Fix the following build failure with gcc 3.2: CC [M] drivers/net/3c59x.o drivers/net/3c59x.c:2726:1: directives may not be used inside a macro argument drivers/net/3c59x.c:2725:59: unterminated argument list invoking macro "pr_err" drivers/net/3c59x.c: In function `dump_tx_ring': drivers/net/3c59x.c:2727: implicit declaration of function `pr_err' drivers/net/3c59x.c:2731: syntax error before ')' token Apparently gcc 3.2 doesn't like #if interleaved with a macro call. Signed-off-by: Jean Delvare Signed-off-by: David S. Miller --- drivers/net/3c59x.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c index c34aee91250b..c20416850948 100644 --- a/drivers/net/3c59x.c +++ b/drivers/net/3c59x.c @@ -2721,13 +2721,15 @@ dump_tx_ring(struct net_device *dev) &vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]); issue_and_wait(dev, DownStall); for (i = 0; i < TX_RING_SIZE; i++) { - pr_err(" %d: @%p length %8.8x status %8.8x\n", i, - &vp->tx_ring[i], + unsigned int length; + #if DO_ZEROCOPY - le32_to_cpu(vp->tx_ring[i].frag[0].length), + length = le32_to_cpu(vp->tx_ring[i].frag[0].length); #else - le32_to_cpu(vp->tx_ring[i].length), + length = le32_to_cpu(vp->tx_ring[i].length); #endif + pr_err(" %d: @%p length %8.8x status %8.8x\n", + i, &vp->tx_ring[i], length, le32_to_cpu(vp->tx_ring[i].status)); } if (!stalled) -- cgit v1.2.3 From c2718348b41a8e7646516d9af8bb0231c6a44374 Mon Sep 17 00:00:00 2001 From: Doug Thompson Date: Tue, 4 Aug 2009 12:02:20 +0200 Subject: amd64_edac: print debug statements only on error Add forgotten return calls for the successful cases. Signed-off-by: Doug Thompson Signed-off-by: Borislav Petkov --- drivers/edac/amd64_edac.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c index 5fa924d61b10..e2a10bcba7a1 100644 --- a/drivers/edac/amd64_edac.c +++ b/drivers/edac/amd64_edac.c @@ -868,6 +868,8 @@ static void amd64_read_dbam_reg(struct amd64_pvt *pvt) goto err_reg; } + return; + err_reg: debugf0("Error reading F2x%03x.\n", reg); } @@ -2634,6 +2636,8 @@ static void amd64_read_mc_registers(struct amd64_pvt *pvt) amd64_dump_misc_regs(pvt); + return; + err_reg: debugf0("Reading an MC register failed\n"); -- cgit v1.2.3 From 1cef8e41073efe47e809f49670eb461307e52ccc Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 27 Jul 2009 11:30:48 +0530 Subject: mfd: twl4030 irq fixes The TWL4030 IRQ handler has a bug which leads to spinlock lock-up. It is calling the 'unmask' function in a process context. :The mask/unmask/ack functions are only designed to be called from the IRQ handler code, or the proper API interfaces found in linux/interrupt.h. Also there is no need to have IRQ chaining mechanism. The right way to handle this is to claim the parent interrupt as a standard interrupt and arrange for handle_twl4030_pih to take care of the rest of the devices. Mail thread on this issue can be found at: http://marc.info/?l=linux-arm-kernel&m=124629940123396&w=2 Signed-off-by: Russell King Tested-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Samuel Ortiz --- drivers/mfd/twl4030-irq.c | 55 +++++++++++++++++++++-------------------------- 1 file changed, 24 insertions(+), 31 deletions(-) (limited to 'drivers') diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c index bae61b22501c..7d430835655f 100644 --- a/drivers/mfd/twl4030-irq.c +++ b/drivers/mfd/twl4030-irq.c @@ -180,14 +180,9 @@ static struct completion irq_event; static int twl4030_irq_thread(void *data) { long irq = (long)data; - struct irq_desc *desc = irq_to_desc(irq); static unsigned i2c_errors; static const unsigned max_i2c_errors = 100; - if (!desc) { - pr_err("twl4030: Invalid IRQ: %ld\n", irq); - return -EINVAL; - } current->flags |= PF_NOFREEZE; @@ -240,7 +235,7 @@ static int twl4030_irq_thread(void *data) } local_irq_enable(); - desc->chip->unmask(irq); + enable_irq(irq); } return 0; @@ -255,25 +250,13 @@ static int twl4030_irq_thread(void *data) * thread. All we do here is acknowledge and mask the interrupt and wakeup * the kernel thread. */ -static void handle_twl4030_pih(unsigned int irq, struct irq_desc *desc) +static irqreturn_t handle_twl4030_pih(int irq, void *devid) { /* Acknowledge, clear *AND* mask the interrupt... */ - desc->chip->ack(irq); - complete(&irq_event); -} - -static struct task_struct *start_twl4030_irq_thread(long irq) -{ - struct task_struct *thread; - - init_completion(&irq_event); - thread = kthread_run(twl4030_irq_thread, (void *)irq, "twl4030-irq"); - if (!thread) - pr_err("twl4030: could not create irq %ld thread!\n", irq); - - return thread; + disable_irq_nosync(irq); + complete(devid); + return IRQ_HANDLED; } - /*----------------------------------------------------------------------*/ /* @@ -734,18 +717,28 @@ int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end) } /* install an irq handler to demultiplex the TWL4030 interrupt */ - task = start_twl4030_irq_thread(irq_num); - if (!task) { - pr_err("twl4030: irq thread FAIL\n"); - status = -ESRCH; - goto fail; - } - set_irq_data(irq_num, task); - set_irq_chained_handler(irq_num, handle_twl4030_pih); - return status; + init_completion(&irq_event); + status = request_irq(irq_num, handle_twl4030_pih, IRQF_DISABLED, + "TWL4030-PIH", &irq_event); + if (status < 0) { + pr_err("twl4030: could not claim irq%d: %d\n", irq_num, status); + goto fail_rqirq; + } + + task = kthread_run(twl4030_irq_thread, (void *)irq_num, "twl4030-irq"); + if (IS_ERR(task)) { + pr_err("twl4030: could not create irq %d thread!\n", irq_num); + status = PTR_ERR(task); + goto fail_kthread; + } + return status; +fail_kthread: + free_irq(irq_num, &irq_event); +fail_rqirq: + /* clean up twl4030_sih_setup */ fail: for (i = irq_base; i < irq_end; i++) set_irq_chip_and_handler(i, NULL, NULL); -- cgit v1.2.3 From 26d204afa18f7df177f21bdb3759e0098ca8f7d5 Mon Sep 17 00:00:00 2001 From: "Pallipadi, Venkatesh" Date: Wed, 29 Jul 2009 13:36:10 -0700 Subject: [CPUFREQ] Fix NULL pointer dereference regression in conservative governor Commit ee88415caf736b89500f16e0a545614541a45005 introduced this regression when it removed enable bit in cpu_dbs_info_s. That added a possibility of dbs_cpufreq_notifier getting called for a CPU that is not yet managed by conservative governor. That will happen as the transition notifier is set as soon as one CPU switches to conservative governor and other CPUs can get a NULL pointer dereference without the enable bit check. Add the enable bit back again. Reported-by: Lermytte Christophe Signed-off-by: Venkatesh Pallipadi Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq_conservative.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/cpufreq/cpufreq_conservative.c b/drivers/cpufreq/cpufreq_conservative.c index 57490502b21c..bdea7e2f94ba 100644 --- a/drivers/cpufreq/cpufreq_conservative.c +++ b/drivers/cpufreq/cpufreq_conservative.c @@ -63,6 +63,7 @@ struct cpu_dbs_info_s { unsigned int down_skip; unsigned int requested_freq; int cpu; + unsigned int enable:1; /* * percpu mutex that serializes governor limit change with * do_dbs_timer invocation. We do not want do_dbs_timer to run @@ -141,6 +142,9 @@ dbs_cpufreq_notifier(struct notifier_block *nb, unsigned long val, struct cpufreq_policy *policy; + if (!this_dbs_info->enable) + return 0; + policy = this_dbs_info->cur_policy; /* @@ -497,6 +501,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info) int delay = usecs_to_jiffies(dbs_tuners_ins.sampling_rate); delay -= jiffies % delay; + dbs_info->enable = 1; INIT_DELAYED_WORK_DEFERRABLE(&dbs_info->work, do_dbs_timer); queue_delayed_work_on(dbs_info->cpu, kconservative_wq, &dbs_info->work, delay); @@ -504,6 +509,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info) static inline void dbs_timer_exit(struct cpu_dbs_info_s *dbs_info) { + dbs_info->enable = 0; cancel_delayed_work_sync(&dbs_info->work); } -- cgit v1.2.3 From 42c74b84c64633dd3badbfc2abd2ef1728b64b30 Mon Sep 17 00:00:00 2001 From: Prarit Bhargava Date: Mon, 3 Aug 2009 10:58:11 -0400 Subject: [CPUFREQ] Do not set policy for offline cpus Suspend/Resume fails on multi socket, multi core systems because the cpufreq code erroneously sets the per_cpu policy_cpu value when a logical cpu is offline. This most notably results in missing sysfs files that are used to set the cpu frequencies of the various cpus. Signed-off-by: Prarit Bhargava Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index b90eda8b3440..120d236c0ffb 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -924,6 +924,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) spin_lock_irqsave(&cpufreq_driver_lock, flags); for_each_cpu(j, policy->cpus) { + if (!cpu_online(j)) + continue; per_cpu(cpufreq_cpu_data, j) = policy; per_cpu(policy_cpu, j) = policy->cpu; } -- cgit v1.2.3 From d5194decd0a6f792b2789eebd4ddf022a248f655 Mon Sep 17 00:00:00 2001 From: Thomas Renninger Date: Wed, 29 Jul 2009 11:26:20 +0200 Subject: [CPUFREQ] Fix a kobject reference bug related to managed CPUs The first offline/online cycle is successful, the second not. Doing: echo 0 >cpu1/online echo 1 >cpu1/online echo 0 >cpu1/online The last command will trigger: Jul 22 14:39:50 linux kernel: [ 593.210125] ------------[ cut here ]------------ Jul 22 14:39:50 linux kernel: [ 593.210139] WARNING: at lib/kref.c:43 kref_get+0x23/0x2b() Jul 22 14:39:50 linux kernel: [ 593.210144] Hardware name: To Be Filled By O.E.M. Jul 22 14:39:50 linux kernel: [ 593.210148] Modules linked in: powernow_k8 Jul 22 14:39:50 linux kernel: [ 593.210158] Pid: 378, comm: kondemand/2 Tainted: G W 2.6.31-rc2 #38 Jul 22 14:39:50 linux kernel: [ 593.210163] Call Trace: Jul 22 14:39:50 linux kernel: [ 593.210171] [] ? kref_get+0x23/0x2b Jul 22 14:39:50 linux kernel: [ 593.210181] [] warn_slowpath_common+0x77/0xa4 Jul 22 14:39:50 linux kernel: [ 593.210190] [] warn_slowpath_null+0xf/0x11 Jul 22 14:39:50 linux kernel: [ 593.210198] [] kref_get+0x23/0x2b Jul 22 14:39:50 linux kernel: [ 593.210206] [] kobject_get+0x1a/0x22 Jul 22 14:39:50 linux kernel: [ 593.210214] [] cpufreq_cpu_get+0x8a/0xcb Jul 22 14:39:50 linux kernel: [ 593.210222] [] __cpufreq_driver_getavg+0x1d/0x67 Jul 22 14:39:50 linux kernel: [ 593.210231] [] do_dbs_timer+0x158/0x27f Jul 22 14:39:50 linux kernel: [ 593.210240] [] worker_thread+0x200/0x313 ... The output continues on every do_dbs_timer ondemand freq checking poll. This regression was introduced by git commit: 3f4a782b5ce2698b1870b5a7b573cd721d4fce33 The policy is released when the cpufreq device is removed in: __cpufreq_remove_dev(): /* if this isn't the CPU which is the parent of the kobj, we * only need to unlink, put and exit */ Not creating the symlink is not sever at all. As long as: sysfs_remove_link(&sys_dev->kobj, "cpufreq"); handles it gracefully that the symlink did not exist. Possibly no error should be returned at all, because ondemand governor would still provide the same functionality. Userspace in userspace gov case might be confused if the link is missing. Resolves http://bugzilla.kernel.org/show_bug.cgi?id=13903 CC: Mathieu Desnoyers CC: Venkatesh Pallipadi Signed-off-by: Thomas Renninger Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index 120d236c0ffb..bd74a0b12176 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -858,6 +858,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) /* Check for existing affected CPUs. * They may not be aware of it due to CPU Hotplug. + * cpufreq_cpu_put is called when the device is removed + * in __cpufreq_remove_dev() */ managed_policy = cpufreq_cpu_get(j); if (unlikely(managed_policy)) { @@ -884,7 +886,7 @@ static int cpufreq_add_dev(struct sys_device *sys_dev) ret = sysfs_create_link(&sys_dev->kobj, &managed_policy->kobj, "cpufreq"); - if (!ret) + if (ret) cpufreq_cpu_put(managed_policy); /* * Success. We only needed to be added to the mask. -- cgit v1.2.3 From 4bc5d34135039566b8d6efa2de7515b2be505da8 Mon Sep 17 00:00:00 2001 From: Dave Jones Date: Tue, 4 Aug 2009 14:03:25 -0400 Subject: [CPUFREQ] Make cpufreq suspend code conditional on powerpc. The suspend code runs with interrupts disabled, and the powerpc workaround we do in the cpufreq suspend hook calls the drivers ->get method. powernow-k8's ->get does an smp_call_function_single which needs interrupts enabled cpufreq's suspend/resume code was added in 42d4dc3f4e1e to work around a hardware problem on ppc powerbooks. If we make all this code conditional on powerpc, we avoid the issue above. Signed-off-by: Dave Jones --- drivers/cpufreq/cpufreq.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c index bd74a0b12176..fd69086d08d5 100644 --- a/drivers/cpufreq/cpufreq.c +++ b/drivers/cpufreq/cpufreq.c @@ -1248,13 +1248,22 @@ EXPORT_SYMBOL(cpufreq_get); static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg) { - int cpu = sysdev->id; int ret = 0; + +#ifdef __powerpc__ + int cpu = sysdev->id; unsigned int cur_freq = 0; struct cpufreq_policy *cpu_policy; dprintk("suspending cpu %u\n", cpu); + /* + * This whole bogosity is here because Powerbooks are made of fail. + * No sane platform should need any of the code below to be run. + * (it's entirely the wrong thing to do, as driver->get may + * reenable interrupts on some architectures). + */ + if (!cpu_online(cpu)) return 0; @@ -1313,6 +1322,7 @@ static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg) out: cpufreq_cpu_put(cpu_policy); +#endif /* __powerpc__ */ return ret; } @@ -1326,12 +1336,18 @@ out: */ static int cpufreq_resume(struct sys_device *sysdev) { - int cpu = sysdev->id; int ret = 0; + +#ifdef __powerpc__ + int cpu = sysdev->id; struct cpufreq_policy *cpu_policy; dprintk("resuming cpu %u\n", cpu); + /* As with the ->suspend method, all the code below is + * only necessary because Powerbooks suck. + * See commit 42d4dc3f4e1e for jokes. */ + if (!cpu_online(cpu)) return 0; @@ -1395,6 +1411,7 @@ out: schedule_work(&cpu_policy->update); fail: cpufreq_cpu_put(cpu_policy); +#endif /* __powerpc__ */ return ret; } -- cgit v1.2.3 From e0cff5ed27acd355264b210d9622da801a431e19 Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Tue, 4 Aug 2009 11:46:41 -0700 Subject: igbvf: Allow VF driver to correctly recognize failure to set mac The VF driver was not correctly recognizing that it did not correctly set it's mac address. As a result the VF driver was unable to receive network traffic until being unloaded and reloaded. The issue was root caused to the fact that the CTS bit was not taken into account when checking for the request being NAKed. Signed-off-by: Alexander Duyck Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/igbvf/vf.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/net/igbvf/vf.c b/drivers/net/igbvf/vf.c index 2a4faf9ade69..a9a61efa964c 100644 --- a/drivers/net/igbvf/vf.c +++ b/drivers/net/igbvf/vf.c @@ -274,6 +274,8 @@ static s32 e1000_set_vfta_vf(struct e1000_hw *hw, u16 vid, bool set) err = mbx->ops.read_posted(hw, msgbuf, 2); + msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS; + /* if nacked the vlan was rejected */ if (!err && (msgbuf[0] == (E1000_VF_SET_VLAN | E1000_VT_MSGTYPE_NACK))) err = -E1000_ERR_MAC_INIT; @@ -317,6 +319,8 @@ static void e1000_rar_set_vf(struct e1000_hw *hw, u8 * addr, u32 index) if (!ret_val) ret_val = mbx->ops.read_posted(hw, msgbuf, 3); + msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS; + /* if nacked the address was rejected, use "perm_addr" */ if (!ret_val && (msgbuf[0] == (E1000_VF_SET_MAC_ADDR | E1000_VT_MSGTYPE_NACK))) -- cgit v1.2.3 From 357eb46d8f275b4e8484541234ea3ba06065e258 Mon Sep 17 00:00:00 2001 From: Hannes Hering Date: Tue, 4 Aug 2009 11:48:39 -0700 Subject: ehea: Fix napi list corruption on ifconfig down This patch fixes the napi list handling when an ehea interface is shut down to avoid corruption of the napi list. Signed-off-by: Hannes Hering Signed-off-by: David S. Miller --- drivers/net/ehea/ehea.h | 2 +- drivers/net/ehea/ehea_main.c | 3 +++ 2 files changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h index 78952f8324e2..fa311a950996 100644 --- a/drivers/net/ehea/ehea.h +++ b/drivers/net/ehea/ehea.h @@ -40,7 +40,7 @@ #include #define DRV_NAME "ehea" -#define DRV_VERSION "EHEA_0101" +#define DRV_VERSION "EHEA_0102" /* eHEA capability flags */ #define DLPAR_PORT_ADD_REM 1 diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index e8d46cc1bec2..977c3d358279 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -1545,6 +1545,9 @@ static int ehea_clean_portres(struct ehea_port *port, struct ehea_port_res *pr) { int ret, i; + if (pr->qp) + netif_napi_del(&pr->napi); + ret = ehea_destroy_qp(pr->qp); if (!ret) { -- cgit v1.2.3 From 18eac1cc100fa2afd5f39085aae6b694e417734b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 10:58:29 -0700 Subject: tty-ldisc: make refcount be atomic_t 'users' count This is pure preparation of changing the ldisc reference counting to be a true refcount that defines the lifetime of the ldisc. But this is a purely syntactic change for now to make the next steps easier. This patch should make no semantic changes at all. But I wanted to make the ldisc refcount be an atomic (I will be touching it without locks soon enough), and I wanted to rename it so that there isn't quite as much confusion between 'ldo->refcount' (ldisk operations refcount) and 'ld->refcount' (ldisc refcount itself) in the same file. So it's now an atomic 'ld->users' count. It still starts at zero, despite having a reference from 'tty->ldisc', but that will change once we turn it into a _real_ refcount. Signed-off-by: Linus Torvalds Tested-by: OGAWA Hirofumi Tested-by: Sergey Senozhatsky Acked-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 18 ++++++++---------- include/linux/tty_ldisc.h | 2 +- 2 files changed, 9 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index acd76b767d4c..fd175e60aad5 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -142,7 +142,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc) /* lock it */ ldops->refcount++; ld->ops = ldops; - ld->refcount = 0; + atomic_set(&ld->users, 0); err = 0; } } @@ -206,7 +206,7 @@ static void tty_ldisc_put(struct tty_ldisc *ld) ldo->refcount--; module_put(ldo->owner); spin_unlock_irqrestore(&tty_ldisc_lock, flags); - WARN_ON(ld->refcount); + WARN_ON(atomic_read(&ld->users)); kfree(ld); } @@ -297,7 +297,7 @@ static int tty_ldisc_try(struct tty_struct *tty) spin_lock_irqsave(&tty_ldisc_lock, flags); ld = tty->ldisc; if (test_bit(TTY_LDISC, &tty->flags)) { - ld->refcount++; + atomic_inc(&ld->users); ret = 1; } spin_unlock_irqrestore(&tty_ldisc_lock, flags); @@ -324,7 +324,7 @@ struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty) { /* wait_event is a macro */ wait_event(tty_ldisc_wait, tty_ldisc_try(tty)); - WARN_ON(tty->ldisc->refcount == 0); + WARN_ON(atomic_read(&tty->ldisc->users) == 0); return tty->ldisc; } EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); @@ -365,11 +365,9 @@ void tty_ldisc_deref(struct tty_ldisc *ld) BUG_ON(ld == NULL); spin_lock_irqsave(&tty_ldisc_lock, flags); - if (ld->refcount == 0) + if (atomic_read(&ld->users) == 0) printk(KERN_ERR "tty_ldisc_deref: no references.\n"); - else - ld->refcount--; - if (ld->refcount == 0) + else if (atomic_dec_and_test(&ld->users)) wake_up(&tty_ldisc_wait); spin_unlock_irqrestore(&tty_ldisc_lock, flags); } @@ -536,10 +534,10 @@ static int tty_ldisc_wait_idle(struct tty_struct *tty) { unsigned long flags; spin_lock_irqsave(&tty_ldisc_lock, flags); - while (tty->ldisc->refcount) { + while (atomic_read(&tty->ldisc->users)) { spin_unlock_irqrestore(&tty_ldisc_lock, flags); if (wait_event_timeout(tty_ldisc_wait, - tty->ldisc->refcount == 0, 5 * HZ) == 0) + atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0) return -EBUSY; spin_lock_irqsave(&tty_ldisc_lock, flags); } diff --git a/include/linux/tty_ldisc.h b/include/linux/tty_ldisc.h index 40f38d896777..0c4ee9b88f85 100644 --- a/include/linux/tty_ldisc.h +++ b/include/linux/tty_ldisc.h @@ -144,7 +144,7 @@ struct tty_ldisc_ops { struct tty_ldisc { struct tty_ldisc_ops *ops; - int refcount; + atomic_t users; }; #define TTY_LDISC_MAGIC 0x5403 -- cgit v1.2.3 From 65b770468e98941e45e19780dff9283e663e6b8b Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 11:11:19 -0700 Subject: tty-ldisc: turn ldisc user count into a proper refcount By using the user count for the actual lifetime rules, we can get rid of the silly "wait_for_idle" logic, because any busy ldisc will automatically stay around until the last user releases it. This avoids a host of odd issues, and simplifies the code. So now, when the last ldisc reference is dropped, we just release the ldisc operations struct reference, and free the ldisc. It looks obvious enough, and it does work for me, but the counting _could_ be off. It probably isn't (bad counting in the new version would generally imply that the old code did something really bad, like free an ldisc with a non-zero count), but it does need some testing, and preferably somebody looking at it. With this change, both 'tty_ldisc_put()' and 'tty_ldisc_deref()' are just aliases for the new ref-counting 'put_ldisc()'. Both of them decrement the ldisc user count and free it if it goes down to zero. They're identical functions, in other words. But the reason they still exist as sepate functions is that one of them was exported (tty_ldisc_deref) and had a stupid name (so I don't want to use it as the main name), and the other one was used in multiple places (and I didn't want to make the patch larger just to rename the users). In addition to the refcounting, I did do some minimal cleanup. For example, now "tty_ldisc_try()" actually returns the ldisc it got under the lock, rather than returning true/false and then the caller would look up the ldisc again (now without the protection of the lock). That said, there's tons of dubious use of 'tty->ldisc' without obviously proper locking or refcounting left. I expressly did _not_ want to try to fix it all, keeping the patch minimal. There may or may not be bugs in that kind of code, but they wouldn't be _new_ bugs. That said, even if the bugs aren't new, the timing and lifetime will change. For example, some silly code may depend on the 'tty->ldisc' pointer not changing because they hold a refcount on the 'ldisc'. And that's no longer true - if you hold a ref on the ldisc, the 'ldisc' itself is safe, but tty->ldisc may change. So the proper locking (remains) to hold tty->ldisc_mutex if you expect tty->ldisc to be stable. That's not really a _new_ rule, but it's an example of something that the old code might have unintentionally depended on and hidden bugs. Whatever. The patch _looks_ sensible to me. The only users of ldisc->users are: - get_ldisc() - atomically increment the count - put_ldisc() - atomically decrements the count and releases if zero - tty_ldisc_try_get() - creates the ldisc, and sets the count to 1. The ldisc should then either be released, or be attached to a tty. Signed-off-by: Linus Torvalds Tested-by: OGAWA Hirofumi Tested-by: Sergey Senozhatsky Acked-by: Alan Cox Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 143 +++++++++++++++-------------------------------- 1 file changed, 46 insertions(+), 97 deletions(-) (limited to 'drivers') diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index fd175e60aad5..be55dfcf59ac 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -48,6 +48,34 @@ static DECLARE_WAIT_QUEUE_HEAD(tty_ldisc_wait); /* Line disc dispatch table */ static struct tty_ldisc_ops *tty_ldiscs[NR_LDISCS]; +static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld) +{ + if (ld) + atomic_inc(&ld->users); + return ld; +} + +static inline void put_ldisc(struct tty_ldisc *ld) +{ + if (WARN_ON_ONCE(!ld)) + return; + + /* + * If this is the last user, free the ldisc, and + * release the ldisc ops. + */ + if (atomic_dec_and_test(&ld->users)) { + unsigned long flags; + struct tty_ldisc_ops *ldo = ld->ops; + + kfree(ld); + spin_lock_irqsave(&tty_ldisc_lock, flags); + ldo->refcount--; + module_put(ldo->owner); + spin_unlock_irqrestore(&tty_ldisc_lock, flags); + } +} + /** * tty_register_ldisc - install a line discipline * @disc: ldisc number @@ -142,7 +170,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc) /* lock it */ ldops->refcount++; ld->ops = ldops; - atomic_set(&ld->users, 0); + atomic_set(&ld->users, 1); err = 0; } } @@ -181,35 +209,6 @@ static struct tty_ldisc *tty_ldisc_get(int disc) return ld; } -/** - * tty_ldisc_put - drop ldisc reference - * @ld: ldisc - * - * Drop a reference to a line discipline. Manage refcounts and - * module usage counts. Free the ldisc once the recount hits zero. - * - * Locking: - * takes tty_ldisc_lock to guard against ldisc races - */ - -static void tty_ldisc_put(struct tty_ldisc *ld) -{ - unsigned long flags; - int disc = ld->ops->num; - struct tty_ldisc_ops *ldo; - - BUG_ON(disc < N_TTY || disc >= NR_LDISCS); - - spin_lock_irqsave(&tty_ldisc_lock, flags); - ldo = tty_ldiscs[disc]; - BUG_ON(ldo->refcount == 0); - ldo->refcount--; - module_put(ldo->owner); - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - WARN_ON(atomic_read(&ld->users)); - kfree(ld); -} - static void *tty_ldiscs_seq_start(struct seq_file *m, loff_t *pos) { return (*pos < NR_LDISCS) ? pos : NULL; @@ -234,7 +233,7 @@ static int tty_ldiscs_seq_show(struct seq_file *m, void *v) if (IS_ERR(ld)) return 0; seq_printf(m, "%-10s %2d\n", ld->ops->name ? ld->ops->name : "???", i); - tty_ldisc_put(ld); + put_ldisc(ld); return 0; } @@ -288,20 +287,17 @@ static void tty_ldisc_assign(struct tty_struct *tty, struct tty_ldisc *ld) * Locking: takes tty_ldisc_lock */ -static int tty_ldisc_try(struct tty_struct *tty) +static struct tty_ldisc *tty_ldisc_try(struct tty_struct *tty) { unsigned long flags; struct tty_ldisc *ld; - int ret = 0; spin_lock_irqsave(&tty_ldisc_lock, flags); - ld = tty->ldisc; - if (test_bit(TTY_LDISC, &tty->flags)) { - atomic_inc(&ld->users); - ret = 1; - } + ld = NULL; + if (test_bit(TTY_LDISC, &tty->flags)) + ld = get_ldisc(tty->ldisc); spin_unlock_irqrestore(&tty_ldisc_lock, flags); - return ret; + return ld; } /** @@ -322,10 +318,11 @@ static int tty_ldisc_try(struct tty_struct *tty) struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty) { + struct tty_ldisc *ld; + /* wait_event is a macro */ - wait_event(tty_ldisc_wait, tty_ldisc_try(tty)); - WARN_ON(atomic_read(&tty->ldisc->users) == 0); - return tty->ldisc; + wait_event(tty_ldisc_wait, (ld = tty_ldisc_try(tty)) != NULL); + return ld; } EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); @@ -342,9 +339,7 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait); struct tty_ldisc *tty_ldisc_ref(struct tty_struct *tty) { - if (tty_ldisc_try(tty)) - return tty->ldisc; - return NULL; + return tty_ldisc_try(tty); } EXPORT_SYMBOL_GPL(tty_ldisc_ref); @@ -360,19 +355,15 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref); void tty_ldisc_deref(struct tty_ldisc *ld) { - unsigned long flags; - - BUG_ON(ld == NULL); - - spin_lock_irqsave(&tty_ldisc_lock, flags); - if (atomic_read(&ld->users) == 0) - printk(KERN_ERR "tty_ldisc_deref: no references.\n"); - else if (atomic_dec_and_test(&ld->users)) - wake_up(&tty_ldisc_wait); - spin_unlock_irqrestore(&tty_ldisc_lock, flags); + put_ldisc(ld); } EXPORT_SYMBOL_GPL(tty_ldisc_deref); +static inline void tty_ldisc_put(struct tty_ldisc *ld) +{ + put_ldisc(ld); +} + /** * tty_ldisc_enable - allow ldisc use * @tty: terminal to activate ldisc on @@ -520,31 +511,6 @@ static int tty_ldisc_halt(struct tty_struct *tty) return cancel_delayed_work(&tty->buf.work); } -/** - * tty_ldisc_wait_idle - wait for the ldisc to become idle - * @tty: tty to wait for - * - * Wait for the line discipline to become idle. The discipline must - * have been halted for this to guarantee it remains idle. - * - * tty_ldisc_lock protects the ref counts currently. - */ - -static int tty_ldisc_wait_idle(struct tty_struct *tty) -{ - unsigned long flags; - spin_lock_irqsave(&tty_ldisc_lock, flags); - while (atomic_read(&tty->ldisc->users)) { - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - if (wait_event_timeout(tty_ldisc_wait, - atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0) - return -EBUSY; - spin_lock_irqsave(&tty_ldisc_lock, flags); - } - spin_unlock_irqrestore(&tty_ldisc_lock, flags); - return 0; -} - /** * tty_set_ldisc - set line discipline * @tty: the terminal to set @@ -640,14 +606,6 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc) flush_scheduled_work(); - /* Let any existing reference holders finish */ - retval = tty_ldisc_wait_idle(tty); - if (retval < 0) { - clear_bit(TTY_LDISC_CHANGING, &tty->flags); - tty_ldisc_put(new_ldisc); - return retval; - } - mutex_lock(&tty->ldisc_mutex); if (test_bit(TTY_HUPPED, &tty->flags)) { /* We were raced by the hangup method. It will have stomped @@ -793,7 +751,6 @@ void tty_ldisc_hangup(struct tty_struct *tty) if (tty->ldisc) { /* Not yet closed */ /* Switch back to N_TTY */ tty_ldisc_halt(tty); - tty_ldisc_wait_idle(tty); tty_ldisc_reinit(tty); /* At this point we have a closed ldisc and we want to reopen it. We could defer this to the next open but @@ -858,14 +815,6 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty) tty_ldisc_halt(tty); flush_scheduled_work(); - /* - * Wait for any short term users (we know they are just driver - * side waiters as the file is closing so user count on the file - * side is zero. - */ - - tty_ldisc_wait_idle(tty); - mutex_lock(&tty->ldisc_mutex); /* * Now kill off the ldisc -- cgit v1.2.3 From cbe9352fa08f90aa03b4dbf1bbabfc95d196e562 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 3 Aug 2009 14:54:56 -0700 Subject: tty-ldisc: be more careful in 'put_ldisc' locking Use 'atomic_dec_and_lock()' to make sure that we always hold the tty_ldisc_lock when the ldisc count goes to zero. That way we can never race against 'tty_ldisc_try()' increasing the count again. Reported-by: OGAWA Hirofumi Signed-off-by: Linus Torvalds Tested-by: Sergey Senozhatsky Signed-off-by: Greg Kroah-Hartman --- drivers/char/tty_ldisc.c | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c index be55dfcf59ac..1733d3439ad2 100644 --- a/drivers/char/tty_ldisc.c +++ b/drivers/char/tty_ldisc.c @@ -55,25 +55,32 @@ static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld) return ld; } -static inline void put_ldisc(struct tty_ldisc *ld) +static void put_ldisc(struct tty_ldisc *ld) { + unsigned long flags; + if (WARN_ON_ONCE(!ld)) return; /* * If this is the last user, free the ldisc, and * release the ldisc ops. + * + * We really want an "atomic_dec_and_lock_irqsave()", + * but we don't have it, so this does it by hand. */ - if (atomic_dec_and_test(&ld->users)) { - unsigned long flags; + local_irq_save(flags); + if (atomic_dec_and_lock(&ld->users, &tty_ldisc_lock)) { struct tty_ldisc_ops *ldo = ld->ops; - kfree(ld); - spin_lock_irqsave(&tty_ldisc_lock, flags); ldo->refcount--; module_put(ldo->owner); spin_unlock_irqrestore(&tty_ldisc_lock, flags); + + kfree(ld); + return; } + local_irq_restore(flags); } /** -- cgit v1.2.3 From 6502fbfaf81b09b3f474bb7b3796257e9450273e Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Tue, 4 Aug 2009 11:24:24 -0400 Subject: drm/radeon: Add support for RS880 chips These are new AMD IGP chips Signed-off-by: Alex Deucher Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r600_cp.c | 22 +++++++++++++++------- drivers/gpu/drm/radeon/radeon_drv.h | 1 + include/drm/drm_pciids.h | 5 +++++ 3 files changed, 21 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r600_cp.c b/drivers/gpu/drm/radeon/r600_cp.c index 146f3570af8e..20f17908b036 100644 --- a/drivers/gpu/drm/radeon/r600_cp.c +++ b/drivers/gpu/drm/radeon/r600_cp.c @@ -384,8 +384,9 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv) DRM_INFO("Loading RV670 PFP Microcode\n"); for (i = 0; i < PFP_UCODE_SIZE; i++) RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RV670_pfp_microcode[i]); - } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { - DRM_INFO("Loading RS780 CP Microcode\n"); + } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { + DRM_INFO("Loading RS780/RS880 CP Microcode\n"); for (i = 0; i < PM4_UCODE_SIZE; i++) { RADEON_WRITE(R600_CP_ME_RAM_DATA, RS780_cp_microcode[i][0]); @@ -396,7 +397,7 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv) } RADEON_WRITE(R600_CP_PFP_UCODE_ADDR, 0); - DRM_INFO("Loading RS780 PFP Microcode\n"); + DRM_INFO("Loading RS780/RS880 PFP Microcode\n"); for (i = 0; i < PFP_UCODE_SIZE; i++) RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RS780_pfp_microcode[i]); } @@ -783,6 +784,7 @@ static void r600_gfx_init(struct drm_device *dev, break; case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: dev_priv->r600_max_pipes = 1; dev_priv->r600_max_tile_pipes = 1; @@ -917,7 +919,8 @@ static void r600_gfx_init(struct drm_device *dev, ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV630) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) RADEON_WRITE(R600_DB_DEBUG, R600_PREZ_MUST_WAIT_FOR_POSTZ_DONE); else RADEON_WRITE(R600_DB_DEBUG, 0); @@ -935,7 +938,8 @@ static void r600_gfx_init(struct drm_device *dev, sq_ms_fifo_sizes = RADEON_READ(R600_SQ_MS_FIFO_SIZES); if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { sq_ms_fifo_sizes = (R600_CACHE_FIFO_SIZE(0xa) | R600_FETCH_FIFO_HIWATER(0xa) | R600_DONE_FIFO_HIWATER(0xe0) | @@ -978,7 +982,8 @@ static void r600_gfx_init(struct drm_device *dev, R600_NUM_ES_STACK_ENTRIES(0)); } else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) { + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) { /* no vertex cache */ sq_config &= ~R600_VC_ENABLE; @@ -1035,7 +1040,8 @@ static void r600_gfx_init(struct drm_device *dev, if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) || ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) || - ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) || + ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_TC_ONLY)); else RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_VC_AND_TC)); @@ -1078,6 +1084,7 @@ static void r600_gfx_init(struct drm_device *dev, break; case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: gs_prim_buffer_depth = 32; break; @@ -1123,6 +1130,7 @@ static void r600_gfx_init(struct drm_device *dev, switch (dev_priv->flags & RADEON_FAMILY_MASK) { case CHIP_RV610: case CHIP_RS780: + case CHIP_RS880: case CHIP_RV620: tc_cntl = R600_TC_L2_SIZE(8); break; diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h index 127d0456f628..3933f8216a34 100644 --- a/drivers/gpu/drm/radeon/radeon_drv.h +++ b/drivers/gpu/drm/radeon/radeon_drv.h @@ -143,6 +143,7 @@ enum radeon_family { CHIP_RV635, CHIP_RV670, CHIP_RS780, + CHIP_RS880, CHIP_RV770, CHIP_RV730, CHIP_RV710, diff --git a/include/drm/drm_pciids.h b/include/drm/drm_pciids.h index 9d4c00491547..853508499d20 100644 --- a/include/drm/drm_pciids.h +++ b/include/drm/drm_pciids.h @@ -370,6 +370,11 @@ {0x1002, 0x9614, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0x1002, 0x9615, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0x1002, 0x9616, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9710, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9711, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9712, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9713, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ + {0x1002, 0x9714, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \ {0, 0, 0} #define r128_PCI_IDS \ -- cgit v1.2.3 From 685aaca751271b2c5191901931a19ccaceeae1ce Mon Sep 17 00:00:00 2001 From: "Jory A. Pratt" Date: Mon, 3 Aug 2009 09:32:34 -0700 Subject: Input: i8042 - add Asus G1S to noloop exception list The synaptic touchpad on the Asus G1S is not properly detected when rebooting machine or on cold boot from time to time. Adding the Asus G1S to the noloop exception table resolves the issue. # dmidecode 2.10 SMBIOS 2.4 present. Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: ASUSTeK Computer Inc. Product Name: G1S Version: 1.0 Wake-up Type: Power Switch SKU Number: Family: Signed-off-by: Jory A. Pratt Signed-off-by: Dmitry Torokhov --- drivers/input/serio/i8042-x86ia64io.h | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h index 924e8ed7f2cf..ae04d8a494e5 100644 --- a/drivers/input/serio/i8042-x86ia64io.h +++ b/drivers/input/serio/i8042-x86ia64io.h @@ -77,6 +77,14 @@ static struct dmi_system_id __initdata i8042_dmi_noloop_table[] = { DMI_MATCH(DMI_BOARD_VERSION, "Rev E"), }, }, + { + .ident = "ASUS G1S", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer Inc."), + DMI_MATCH(DMI_BOARD_NAME, "G1S"), + DMI_MATCH(DMI_BOARD_VERSION, "1.0"), + }, + }, { /* AUX LOOP command does not raise AUX IRQ */ .ident = "ASUS P65UP5", -- cgit v1.2.3 From f532959b77e5e567c84c914cb7c7b07d2582448b Mon Sep 17 00:00:00 2001 From: Fenghua Yu Date: Tue, 4 Aug 2009 15:09:37 -0700 Subject: intel-iommu: Correct sglist size calculation. In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded rounding code for calculating the size of each sg elem. This means that on IA64 we correctly round up to the MM page size, not just to the VT-d page size. Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls domain_sg_mapping() -- the 'size' variable is in VT-d pages already. Signed-off-by: Fenghua Yu Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index ebc9b8dca881..11b317a78b49 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -1648,6 +1648,14 @@ static int domain_context_mapped(struct pci_dev *pdev) tmp->devfn); } +/* Returns a number of VTD pages, but aligned to MM page size */ +static inline unsigned long aligned_nrpages(unsigned long host_addr, + size_t size) +{ + host_addr &= ~PAGE_MASK; + return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT; +} + static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn, struct scatterlist *sg, unsigned long phys_pfn, unsigned long nr_pages, int prot) @@ -1675,7 +1683,7 @@ static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn, uint64_t tmp; if (!sg_res) { - sg_res = (sg->offset + sg->length + VTD_PAGE_SIZE - 1) >> VTD_PAGE_SHIFT; + sg_res = aligned_nrpages(sg->offset, sg->length); sg->dma_address = ((dma_addr_t)iov_pfn << VTD_PAGE_SHIFT) + sg->offset; sg->dma_length = sg->length; pteval = page_to_phys(sg_page(sg)) | prot; @@ -2415,14 +2423,6 @@ error: return ret; } -/* Returns a number of VTD pages, but aligned to MM page size */ -static inline unsigned long aligned_nrpages(unsigned long host_addr, - size_t size) -{ - host_addr &= ~PAGE_MASK; - return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT; -} - /* This takes a number of _MM_ pages, not VTD pages */ static struct iova *intel_alloc_iova(struct device *dev, struct dmar_domain *domain, @@ -2875,7 +2875,7 @@ static int intel_map_sg(struct device *hwdev, struct scatterlist *sglist, int ne start_vpfn = mm_to_dma_pfn(iova->pfn_lo); - ret = domain_sg_mapping(domain, start_vpfn, sglist, mm_to_dma_pfn(size), prot); + ret = domain_sg_mapping(domain, start_vpfn, sglist, size, prot); if (unlikely(ret)) { /* clear the page */ dma_pte_clear_range(domain, start_vpfn, -- cgit v1.2.3 From 33041ec049d39a6e0463c7edc7b6f631d24559e3 Mon Sep 17 00:00:00 2001 From: Fenghua Yu Date: Tue, 4 Aug 2009 15:10:59 -0700 Subject: intel-iommu: Mask physical address to correct page size in intel_map_single() The physical address passed to domain_pfn_mapping() should be rounded down to the start of the MM page, not the VT-d page. This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64 platforms. Signed-off-by: Fenghua Yu Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index 11b317a78b49..af7ff9b5aed8 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -2551,6 +2551,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr, int prot = 0; int ret; struct intel_iommu *iommu; + unsigned long paddr_pfn = paddr >> PAGE_SHIFT; BUG_ON(dir == DMA_NONE); @@ -2585,7 +2586,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr, * is not a big problem */ ret = domain_pfn_mapping(domain, mm_to_dma_pfn(iova->pfn_lo), - paddr >> VTD_PAGE_SHIFT, size, prot); + mm_to_dma_pfn(paddr_pfn), size, prot); if (ret) goto error; -- cgit v1.2.3 From f60f785679b507cbeeb03d2db080ab649ac86027 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Tue, 4 Aug 2009 10:39:03 +0000 Subject: netxen: fix dma mask update calculation Fix dma mask calculation that caps at 63-bit addressing even when firmware advertises full 64-bit support. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 3cd8cfcf627b..70c05c4c0cab 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -260,7 +260,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter) change = 0; shift = NXRD32(adapter, CRB_DMA_SHIFT); - if (shift >= 32) + if (shift > 32) return 0; if (NX_IS_REVISION_P3(adapter->ahw.revision_id) && (shift > 9)) @@ -272,7 +272,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter) old_mask = pdev->dma_mask; old_cmask = pdev->dev.coherent_dma_mask; - mask = (1ULL<<(32+shift)) - 1; + mask = DMA_BIT_MASK(32+shift); err = pci_set_dma_mask(pdev, mask); if (err) -- cgit v1.2.3 From 9c9fe1f841745184bbc5460c6f3909fded3b929b Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Mon, 3 Aug 2009 16:09:16 -0700 Subject: drm/i915: Use our own workqueue to avoid wedging the system along with the GPU. Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_dma.c | 15 +++++++++++++-- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/i915_gem.c | 4 ++-- drivers/gpu/drm/i915/i915_irq.c | 5 +++-- 4 files changed, 19 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c index 8c4783180bf6..50d1f782768c 100644 --- a/drivers/gpu/drm/i915/i915_dma.c +++ b/drivers/gpu/drm/i915/i915_dma.c @@ -1186,6 +1186,13 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) if (ret) goto out_iomapfree; + dev_priv->wq = create_workqueue("i915"); + if (dev_priv->wq == NULL) { + DRM_ERROR("Failed to create our workqueue.\n"); + ret = -ENOMEM; + goto out_iomapfree; + } + /* enable GEM by default */ dev_priv->has_gem = 1; @@ -1211,7 +1218,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) if (!I915_NEED_GFX_HWS(dev)) { ret = i915_init_phys_hws(dev); if (ret != 0) - goto out_iomapfree; + goto out_workqueue_free; } i915_get_mem_freq(dev); @@ -1245,7 +1252,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) ret = i915_load_modeset_init(dev, prealloc_size, agp_size); if (ret < 0) { DRM_ERROR("failed to init modeset\n"); - goto out_rmmap; + goto out_workqueue_free; } } @@ -1256,6 +1263,8 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags) return 0; +out_workqueue_free: + destroy_workqueue(dev_priv->wq); out_iomapfree: io_mapping_free(dev_priv->mm.gtt_mapping); out_rmmap: @@ -1269,6 +1278,8 @@ int i915_driver_unload(struct drm_device *dev) { struct drm_i915_private *dev_priv = dev->dev_private; + destroy_workqueue(dev_priv->wq); + io_mapping_free(dev_priv->mm.gtt_mapping); if (dev_priv->mm.gtt_mtrr >= 0) { mtrr_del(dev_priv->mm.gtt_mtrr, dev->agp->base, diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index 5f3a259d95e9..7537f57d8a87 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -231,6 +231,7 @@ typedef struct drm_i915_private { spinlock_t error_lock; struct drm_i915_error_state *first_error; struct work_struct error_work; + struct workqueue_struct *wq; /* Register state */ u8 saveLBB; diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c index 5bf420378b6d..140bee142fc2 100644 --- a/drivers/gpu/drm/i915/i915_gem.c +++ b/drivers/gpu/drm/i915/i915_gem.c @@ -1570,7 +1570,7 @@ i915_add_request(struct drm_device *dev, struct drm_file *file_priv, } if (was_empty && !dev_priv->mm.suspended) - schedule_delayed_work(&dev_priv->mm.retire_work, HZ); + queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ); return seqno; } @@ -1719,7 +1719,7 @@ i915_gem_retire_work_handler(struct work_struct *work) i915_gem_retire_requests(dev); if (!dev_priv->mm.suspended && !list_empty(&dev_priv->mm.request_list)) - schedule_delayed_work(&dev_priv->mm.retire_work, HZ); + queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ); mutex_unlock(&dev->struct_mutex); } diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index f340b3fd54e6..83aee80e77a6 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -482,7 +482,7 @@ static void i915_handle_error(struct drm_device *dev) I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT); } - schedule_work(&dev_priv->error_work); + queue_work(dev_priv->wq, &dev_priv->error_work); } irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) @@ -560,7 +560,8 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS) DRM_DEBUG("hotplug event received, stat 0x%08x\n", hotplug_status); if (hotplug_status & dev_priv->hotplug_supported_mask) - schedule_work(&dev_priv->hotplug_work); + queue_work(dev_priv->wq, + &dev_priv->hotplug_work); I915_WRITE(PORT_HOTPLUG_STAT, hotplug_status); I915_READ(PORT_HOTPLUG_STAT); -- cgit v1.2.3 From 819e0064634f580ab618189e657ea58341d214b7 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Sun, 26 Jul 2009 00:50:38 +0200 Subject: drm/i915: Fix read outside array bounds in restoring the SWF10 range. dev_priv->saveSWF1 is a 16 element array, but this reads up to index 22, and restored values from the wrong registers. Signed-off-by: Roel Kluin Signed-off-by: Eric Anholt --- drivers/gpu/drm/i915/i915_suspend.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_suspend.c b/drivers/gpu/drm/i915/i915_suspend.c index 9e1d16e5c3ea..1d04e1904ac6 100644 --- a/drivers/gpu/drm/i915/i915_suspend.c +++ b/drivers/gpu/drm/i915/i915_suspend.c @@ -598,7 +598,7 @@ int i915_restore_state(struct drm_device *dev) for (i = 0; i < 16; i++) { I915_WRITE(SWF00 + (i << 2), dev_priv->saveSWF0[i]); - I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i+7]); + I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i]); } for (i = 0; i < 3; i++) I915_WRITE(SWF30 + (i << 2), dev_priv->saveSWF2[i]); -- cgit v1.2.3 From 0a51810aa058a0a4ac76dd6f87f4d10bee774e2e Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Tue, 4 Aug 2009 19:55:56 +0100 Subject: ARM: 5637/1: [KS8695] Don't reference CLOCK_TICK_RATE in drivers Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer to a KS8695_CLOCK_RATE. Issue pointed out by Russell King on arm-linux-kernel mailing list. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/include/mach/hardware.h | 5 +++++ arch/arm/mach-ks8695/include/mach/timex.h | 5 +++-- drivers/serial/serial_ks8695.c | 2 +- drivers/watchdog/ks8695_wdt.c | 4 ++-- 4 files changed, 11 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/arch/arm/mach-ks8695/include/mach/hardware.h b/arch/arm/mach-ks8695/include/mach/hardware.h index 1d640d075b7e..e0f911d9e021 100644 --- a/arch/arm/mach-ks8695/include/mach/hardware.h +++ b/arch/arm/mach-ks8695/include/mach/hardware.h @@ -16,6 +16,11 @@ #include +/* + * Clocks are derived from MCLK, which is 25Mhz + */ +#define KS8695_CLOCK_RATE 25000000 + /* * Physical RAM address. */ diff --git a/arch/arm/mach-ks8695/include/mach/timex.h b/arch/arm/mach-ks8695/include/mach/timex.h index 4682e350369b..10f716371bd3 100644 --- a/arch/arm/mach-ks8695/include/mach/timex.h +++ b/arch/arm/mach-ks8695/include/mach/timex.h @@ -14,7 +14,8 @@ #ifndef __ASM_ARCH_TIMEX_H #define __ASM_ARCH_TIMEX_H -/* timers are derived from MCLK, which is 25MHz */ -#define CLOCK_TICK_RATE 25000000 +#include + +#define CLOCK_TICK_RATE KS8695_CLOCK_RATE #endif diff --git a/drivers/serial/serial_ks8695.c b/drivers/serial/serial_ks8695.c index 998e89dc5aaf..e0665630e4da 100644 --- a/drivers/serial/serial_ks8695.c +++ b/drivers/serial/serial_ks8695.c @@ -549,7 +549,7 @@ static struct uart_port ks8695uart_ports[SERIAL_KS8695_NR] = { .mapbase = KS8695_UART_VA, .iotype = SERIAL_IO_MEM, .irq = KS8695_IRQ_UART_TX, - .uartclk = CLOCK_TICK_RATE * 16, + .uartclk = KS8695_CLOCK_RATE * 16, .fifosize = 16, .ops = &ks8695uart_pops, .flags = ASYNC_BOOT_AUTOCONF, diff --git a/drivers/watchdog/ks8695_wdt.c b/drivers/watchdog/ks8695_wdt.c index 00b03eb43bf0..e1c82769b08e 100644 --- a/drivers/watchdog/ks8695_wdt.c +++ b/drivers/watchdog/ks8695_wdt.c @@ -66,7 +66,7 @@ static inline void ks8695_wdt_stop(void) static inline void ks8695_wdt_start(void) { unsigned long tmcon; - unsigned long tval = wdt_time * CLOCK_TICK_RATE; + unsigned long tval = wdt_time * KS8695_CLOCK_RATE; spin_lock(&ks8695_lock); /* disable timer0 */ @@ -103,7 +103,7 @@ static inline void ks8695_wdt_reload(void) static int ks8695_wdt_settimeout(int new_time) { /* - * All counting occurs at SLOW_CLOCK / 128 = 0.256 Hz + * All counting occurs at KS8695_CLOCK_RATE / 128 = 0.256 Hz * * Since WDV is a 16-bit counter, the maximum period is * 65536 / 0.256 = 256 seconds. -- cgit v1.2.3 From b4adbb4ddf63091f48668e7ff1b9b0f6f84d4b40 Mon Sep 17 00:00:00 2001 From: Pascal Terjan Date: Wed, 5 Aug 2009 04:11:39 +0000 Subject: Add IDs for 3C905B-TX Fast Etherlink XL PCI We found this old card which was not supported, and physically looks similar to the other 3C905B we have (9055). After adding the IDs it seems to work fine (MII report, dhcp, scp, ...) Acked-by: Steffen Klassert Signed-off-by: David S. Miller --- drivers/net/3c59x.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c index c20416850948..45675889850b 100644 --- a/drivers/net/3c59x.c +++ b/drivers/net/3c59x.c @@ -235,6 +235,7 @@ enum vortex_chips { CH_3C900B_FL, CH_3C905_1, CH_3C905_2, + CH_3C905B_TX, CH_3C905B_1, CH_3C905B_2, @@ -307,6 +308,8 @@ static struct vortex_chip_info { PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, }, {"3c905 Boomerang 100baseT4", PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, }, + {"3C905B-TX Fast Etherlink XL PCI", + PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, }, {"3c905B Cyclone 100baseTx", PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, }, @@ -389,6 +392,7 @@ static struct pci_device_id vortex_pci_tbl[] = { { 0x10B7, 0x900A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C900B_FL }, { 0x10B7, 0x9050, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_1 }, { 0x10B7, 0x9051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_2 }, + { 0x10B7, 0x9054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_TX }, { 0x10B7, 0x9055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_1 }, { 0x10B7, 0x9058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_2 }, -- cgit v1.2.3 From 985fe845aea9cd56fd351800302270444556e45a Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Wed, 29 Jul 2009 18:55:53 +0200 Subject: drm/radeon/kms: Fix caching mode selection for GTT object GTT object can either be cached,uncached or wc just let core ttm pick the best mode according to how the bo driver and GTT memory type was initialized. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_object.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index dd9ac2fed6d6..e98cae3bf4a6 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -106,7 +106,7 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain) flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; } if (domain & RADEON_GEM_DOMAIN_GTT) { - flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED; + flags |= TTM_PL_FLAG_TT | TTM_PL_MASK_CACHING; } if (domain & RADEON_GEM_DOMAIN_CPU) { flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING; -- cgit v1.2.3 From 194934785a846e0a7b1b674b7b475a9d0125d2f8 Mon Sep 17 00:00:00 2001 From: TJ Date: Mon, 3 Aug 2009 13:39:09 -0700 Subject: Input: wistron_btns - support Prestigio Wifi RF kill button The Prestigio 157, an old no-name clone laptop uses input keys very similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled wireless radio frequency kill switch. This patch adds support for the RF kill switch control and adds manual identification of the model. The Prestigio does not expose any recognisable identity via dmidecode and so requires manual selection at module init using force=1 keymap=prestigio Signed-off-by: TJ Signed-off-by: Dmitry Torokhov --- drivers/input/misc/wistron_btns.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'drivers') diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c index 26e17a9a22eb..27ee976eb54c 100644 --- a/drivers/input/misc/wistron_btns.c +++ b/drivers/input/misc/wistron_btns.c @@ -611,6 +611,20 @@ static struct key_entry keymap_wistron_generic[] __initdata = { { KE_END, 0 } }; +static struct key_entry keymap_prestigio[] __initdata = { + { KE_KEY, 0x11, {KEY_PROG1} }, + { KE_KEY, 0x12, {KEY_PROG2} }, + { KE_WIFI, 0x30 }, + { KE_KEY, 0x22, {KEY_REWIND} }, + { KE_KEY, 0x23, {KEY_FORWARD} }, + { KE_KEY, 0x24, {KEY_PLAYPAUSE} }, + { KE_KEY, 0x25, {KEY_STOPCD} }, + { KE_KEY, 0x31, {KEY_MAIL} }, + { KE_KEY, 0x36, {KEY_WWW} }, + { KE_END, 0 } +}; + + /* * If your machine is not here (which is currently rather likely), please send * a list of buttons and their key codes (reported when loading this module @@ -971,6 +985,8 @@ static int __init select_keymap(void) if (keymap_name != NULL) { if (strcmp (keymap_name, "1557/MS2141") == 0) keymap = keymap_wistron_ms2141; + else if (strcmp (keymap_name, "prestigio") == 0) + keymap = keymap_prestigio; else if (strcmp (keymap_name, "generic") == 0) keymap = keymap_wistron_generic; else { -- cgit v1.2.3 From d82f1c35348cebe2fb2d4a4d31ce0ab0769e3d93 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 5 Aug 2009 01:24:41 -0700 Subject: Input: matrix_keypad - make matrix keymap size dynamic Remove assumption on the shift and size of rows/columns form matrix_keypad driver. Signed-off-by: Eric Miao Signed-off-by: Dmitry Torokhov --- drivers/input/keyboard/matrix_keypad.c | 18 +++++++++--------- include/linux/input/matrix_keypad.h | 13 +++++++------ 2 files changed, 16 insertions(+), 15 deletions(-) (limited to 'drivers') diff --git a/drivers/input/keyboard/matrix_keypad.c b/drivers/input/keyboard/matrix_keypad.c index e9b2e7cb05be..541b981ff075 100644 --- a/drivers/input/keyboard/matrix_keypad.c +++ b/drivers/input/keyboard/matrix_keypad.c @@ -27,6 +27,7 @@ struct matrix_keypad { const struct matrix_keypad_platform_data *pdata; struct input_dev *input_dev; unsigned short *keycodes; + unsigned int row_shift; uint32_t last_key_state[MATRIX_MAX_COLS]; struct delayed_work work; @@ -136,7 +137,7 @@ static void matrix_keypad_scan(struct work_struct *work) if ((bits_changed & (1 << row)) == 0) continue; - code = (row << 4) + col; + code = MATRIX_SCAN_CODE(row, col, keypad->row_shift); input_event(input_dev, EV_MSC, MSC_SCAN, code); input_report_key(input_dev, keypad->keycodes[code], @@ -317,6 +318,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) struct matrix_keypad *keypad; struct input_dev *input_dev; unsigned short *keycodes; + unsigned int row_shift; int i; int err; @@ -332,14 +334,11 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) return -EINVAL; } - if (!keymap_data->max_keymap_size) { - dev_err(&pdev->dev, "invalid keymap data supplied\n"); - return -EINVAL; - } + row_shift = get_count_order(pdata->num_col_gpios); keypad = kzalloc(sizeof(struct matrix_keypad), GFP_KERNEL); - keycodes = kzalloc(keymap_data->max_keymap_size * - sizeof(keypad->keycodes), + keycodes = kzalloc((pdata->num_row_gpios << row_shift) * + sizeof(*keycodes), GFP_KERNEL); input_dev = input_allocate_device(); if (!keypad || !keycodes || !input_dev) { @@ -350,6 +349,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) keypad->input_dev = input_dev; keypad->pdata = pdata; keypad->keycodes = keycodes; + keypad->row_shift = row_shift; keypad->stopped = true; INIT_DELAYED_WORK(&keypad->work, matrix_keypad_scan); spin_lock_init(&keypad->lock); @@ -363,7 +363,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) input_dev->keycode = keycodes; input_dev->keycodesize = sizeof(*keycodes); - input_dev->keycodemax = keymap_data->max_keymap_size; + input_dev->keycodemax = pdata->num_row_gpios << keypad->row_shift; for (i = 0; i < keymap_data->keymap_size; i++) { unsigned int key = keymap_data->keymap[i]; @@ -371,7 +371,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev) unsigned int col = KEY_COL(key); unsigned short code = KEY_VAL(key); - keycodes[(row << 4) + col] = code; + keycodes[MATRIX_SCAN_CODE(row, col, row_shift)] = code; __set_bit(code, input_dev->keybit); } __clear_bit(KEY_RESERVED, input_dev->keybit); diff --git a/include/linux/input/matrix_keypad.h b/include/linux/input/matrix_keypad.h index 7964516c6954..15d5903af2dd 100644 --- a/include/linux/input/matrix_keypad.h +++ b/include/linux/input/matrix_keypad.h @@ -15,12 +15,13 @@ #define KEY_COL(k) (((k) >> 16) & 0xff) #define KEY_VAL(k) ((k) & 0xffff) +#define MATRIX_SCAN_CODE(row, col, row_shift) (((row) << (row_shift)) + (col)) + /** * struct matrix_keymap_data - keymap for matrix keyboards * @keymap: pointer to array of uint32 values encoded with KEY() macro * representing keymap * @keymap_size: number of entries (initialized) in this keymap - * @max_keymap_size: maximum size of keymap supported by the device * * This structure is supposed to be used by platform code to supply * keymaps to drivers that implement matrix-like keypads/keyboards. @@ -28,14 +29,13 @@ struct matrix_keymap_data { const uint32_t *keymap; unsigned int keymap_size; - unsigned int max_keymap_size; }; /** * struct matrix_keypad_platform_data - platform-dependent keypad data * @keymap_data: pointer to &matrix_keymap_data - * @row_gpios: array of gpio numbers reporesenting rows - * @col_gpios: array of gpio numbers reporesenting colums + * @row_gpios: pointer to array of gpio numbers representing rows + * @col_gpios: pointer to array of gpio numbers reporesenting colums * @num_row_gpios: actual number of row gpios used by device * @num_col_gpios: actual number of col gpios used by device * @col_scan_delay_us: delay, measured in microseconds, that is @@ -48,8 +48,9 @@ struct matrix_keymap_data { struct matrix_keypad_platform_data { const struct matrix_keymap_data *keymap_data; - unsigned int row_gpios[MATRIX_MAX_ROWS]; - unsigned int col_gpios[MATRIX_MAX_COLS]; + const unsigned int *row_gpios; + const unsigned int *col_gpios; + unsigned int num_row_gpios; unsigned int num_col_gpios; -- cgit v1.2.3 From c5b1525533c484238015c48c78f86d49a1bfb86b Mon Sep 17 00:00:00 2001 From: Sheng Yang Date: Thu, 6 Aug 2009 13:31:56 +0800 Subject: intel-iommu: Fix enabling snooping feature by mistake Two defects work together result in KVM device passthrough randomly can't work: 1. iommu_snooping is not initialized to zero when vm_iommu_init() called. So it is possible to get a random value. 2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support") change the code path, let it bypass domain_update_iommu_cap(), as well as missing the increment of domain iommu reference count. The latter is also likely to cause a leak of domains on repeated VMM assignment and deassignment. Signed-off-by: Sheng Yang Signed-off-by: David Woodhouse --- drivers/pci/intel-iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c index af7ff9b5aed8..2314ad7ee5fe 100644 --- a/drivers/pci/intel-iommu.c +++ b/drivers/pci/intel-iommu.c @@ -1505,7 +1505,6 @@ static int domain_context_mapping_one(struct dmar_domain *domain, int segment, } set_bit(num, iommu->domain_ids); - set_bit(iommu->seq_id, &domain->iommu_bmp); iommu->domains[num] = domain; id = num; } @@ -3409,6 +3408,7 @@ static int md_domain_init(struct dmar_domain *domain, int guest_width) domain->iommu_count = 0; domain->iommu_coherency = 0; + domain->iommu_snooping = 0; domain->max_addr = 0; /* always allocate the top pgd */ -- cgit v1.2.3 From 17332925d7b11bb6c2d0c49450ae58dd836005da Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Fri, 7 Aug 2009 11:03:26 +1000 Subject: drm/radeon/kms: setup MC/VRAM the same way for suspend/resume we should align the GTT after VRAM no matter what, as we can come back from resume and put in a different place and bad things happen. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_device.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index a162ade74b7f..9ff6dcb97f9d 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -152,7 +152,9 @@ int radeon_mc_setup(struct radeon_device *rdev) } } else { rdev->mc.vram_location = 0; - rdev->mc.gtt_location = rdev->mc.mc_vram_size; + tmp = rdev->mc.mc_vram_size; + tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1); + rdev->mc.gtt_location = tmp; } DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20); DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n", -- cgit v1.2.3 From 7dd2459d8f7a967bcd1466591aec72bb3ddc07cc Mon Sep 17 00:00:00 2001 From: Zhu Yi Date: Mon, 27 Jul 2009 10:10:20 +0800 Subject: ipw2x00: Write outside array bounds > channel_index loops up to IPW_SCAN_CHANNELS, but is used after being > incremented. This might be able to access 1 past the end of the array Reported-by: Roel Kluin Signed-off-by: John W. Linville --- drivers/net/wireless/ipw2x00/ipw2200.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c index 44c29b3f6728..6dcac73b4d29 100644 --- a/drivers/net/wireless/ipw2x00/ipw2200.c +++ b/drivers/net/wireless/ipw2x00/ipw2200.c @@ -6226,7 +6226,7 @@ static void ipw_add_scan_channels(struct ipw_priv *priv, }; u8 channel; - while (channel_index < IPW_SCAN_CHANNELS) { + while (channel_index < IPW_SCAN_CHANNELS - 1) { channel = priv->speed_scan[priv->speed_scan_pos]; if (channel == 0) { -- cgit v1.2.3 From d25f9f1357139bbdc79bc960ea84909a7c22ec2b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:26 +0200 Subject: mwl8k: fix NULL pointer dereference on receive out-of-memory When we go into out-of-memory and fail to allocate skbuffs to refill the receive ring with, rxq_process can end up running into a receive ring entry that is marked as host-owned but doesn't have an associated skbuff. If this happens, we must break out of the rx processing loop instead of trying to process the descriptor. Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index a263d5c84c08..71f3eb67981e 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1012,6 +1012,8 @@ static int rxq_process(struct ieee80211_hw *hw, int index, int limit) rmb(); skb = rxq->rx_skb[rxq->rx_head]; + if (skb == NULL) + break; rxq->rx_skb[rxq->rx_head] = NULL; rxq->rx_head = (rxq->rx_head + 1) % MWL8K_RX_DESCS; -- cgit v1.2.3 From 4ff6432ea620ba467e50ec04b8271ea0eb94e62e Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:39 +0200 Subject: mwl8k: add various missing GET_HW_SPEC endian conversions Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 71f3eb67981e..9643aa4751c9 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1656,18 +1656,18 @@ static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw) memset(cmd->perm_addr, 0xff, sizeof(cmd->perm_addr)); cmd->ps_cookie = cpu_to_le32(priv->cookie_dma); cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rx_desc_dma); - cmd->num_tx_queues = MWL8K_TX_QUEUES; + cmd->num_tx_queues = cpu_to_le32(MWL8K_TX_QUEUES); for (i = 0; i < MWL8K_TX_QUEUES; i++) cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].tx_desc_dma); - cmd->num_tx_desc_per_queue = MWL8K_TX_DESCS; - cmd->total_rx_desc = MWL8K_RX_DESCS; + cmd->num_tx_desc_per_queue = cpu_to_le32(MWL8K_TX_DESCS); + cmd->total_rx_desc = cpu_to_le32(MWL8K_RX_DESCS); rc = mwl8k_post_cmd(hw, &cmd->header); if (!rc) { SET_IEEE80211_PERM_ADDR(hw, cmd->perm_addr); priv->num_mcaddrs = le16_to_cpu(cmd->num_mcaddrs); - priv->fw_rev = cmd->fw_rev; + priv->fw_rev = le32_to_cpu(cmd->fw_rev); priv->hw_rev = cmd->hw_rev; priv->region_code = le16_to_cpu(cmd->region_code); } -- cgit v1.2.3 From 37055bd455b31b8220c35a1ede9c6aceb791cc88 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:47 +0200 Subject: mwl8k: call pci_unmap_single() before accessing command structure again Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 9643aa4751c9..25423c05aff1 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -1593,6 +1593,9 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) timeout = wait_for_completion_timeout(&cmd_wait, msecs_to_jiffies(MWL8K_CMD_TIMEOUT_MS)); + pci_unmap_single(priv->pdev, dma_addr, dma_size, + PCI_DMA_BIDIRECTIONAL); + result = &cmd->result; if (!timeout) { spin_lock_irq(&priv->fw_lock); @@ -1612,8 +1615,6 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd) *result); } - pci_unmap_single(priv->pdev, dma_addr, dma_size, - PCI_DMA_BIDIRECTIONAL); return rc; } -- cgit v1.2.3 From a94cc97e14c5750ec2b50b2e4ecdfb0f369ed0f4 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:58:57 +0200 Subject: mwl8k: prevent crash in ->configure_filter() if no interface was added Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 25423c05aff1..6e491171f73e 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -261,7 +261,7 @@ struct mwl8k_vif { */ }; -#define MWL8K_VIF(_vif) (struct mwl8k_vif *)(&((_vif)->drv_priv)) +#define MWL8K_VIF(_vif) ((struct mwl8k_vif *)&((_vif)->drv_priv)) static const struct ieee80211_channel mwl8k_channels[] = { { .center_freq = 2412, .hw_value = 1, }, @@ -3219,15 +3219,19 @@ static int mwl8k_configure_filter_wt(struct work_struct *wt) struct dev_addr_list *mclist = worker->mclist; struct mwl8k_priv *priv = hw->priv; - struct mwl8k_vif *mv_vif; int rc = 0; if (changed_flags & FIF_BCN_PRBRESP_PROMISC) { if (*total_flags & FIF_BCN_PRBRESP_PROMISC) rc = mwl8k_cmd_set_pre_scan(hw); else { - mv_vif = MWL8K_VIF(priv->vif); - rc = mwl8k_cmd_set_post_scan(hw, mv_vif->bssid); + u8 *bssid; + + bssid = "\x00\x00\x00\x00\x00\x00"; + if (priv->vif != NULL) + bssid = MWL8K_VIF(priv->vif)->bssid; + + rc = mwl8k_cmd_set_post_scan(hw, bssid); } } -- cgit v1.2.3 From 60aa569f9212a13382c29cc734f275dec0f55e0b Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Mon, 3 Aug 2009 21:59:09 +0200 Subject: mwl8k: prevent module unload hang We need to unregister our ieee80211_hw before resetting the chip, as the former causes firmware commands to be issued which will time out once the chip has been reset. Signed-off-by: Lennert Buytenhek Acked-by: Nicolas Pitre Signed-off-by: John W. Linville --- drivers/net/wireless/mwl8k.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c index 6e491171f73e..83967afe0821 100644 --- a/drivers/net/wireless/mwl8k.c +++ b/drivers/net/wireless/mwl8k.c @@ -3733,6 +3733,8 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) ieee80211_stop_queues(hw); + ieee80211_unregister_hw(hw); + /* Remove tx reclaim tasklet */ tasklet_kill(&priv->tx_reclaim_task); @@ -3746,8 +3748,6 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev) for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_reclaim(hw, i, 1); - ieee80211_unregister_hw(hw); - for (i = 0; i < MWL8K_TX_QUEUES; i++) mwl8k_txq_deinit(hw, i); -- cgit v1.2.3 From dd1f57ecaf9688efa69d982652ecfa3e64f1fa55 Mon Sep 17 00:00:00 2001 From: Bob Dunlop Date: Thu, 6 Aug 2009 12:01:03 -0400 Subject: libertas: correct packing of rxpd structure Older Gcc compilers (3.4.5 tested) need additional hints in order to get the packing of the rxpd structure (which contains a 16 bit union) correct on the ARM processor. struct txpd does not need these hints since it contains a 32 bit union that packs naturally. Signed-off-by: R.J.Dunlop Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/hostcmd.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/hostcmd.h b/drivers/net/wireless/libertas/hostcmd.h index 0a2e29140add..c8a1998d4744 100644 --- a/drivers/net/wireless/libertas/hostcmd.h +++ b/drivers/net/wireless/libertas/hostcmd.h @@ -56,8 +56,8 @@ struct rxpd { u8 bss_type; /* BSS number */ u8 bss_num; - } bss; - } u; + } __attribute__ ((packed)) bss; + } __attribute__ ((packed)) u; /* SNR */ u8 snr; -- cgit v1.2.3 From d25f14389a65c7f95512b01415d8d4a8d62855ab Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Mon, 27 Jul 2009 12:05:38 +0900 Subject: PCI hotplug: SGI hotplug: fix build failure The commit bd3d99c17039fd05a29587db3f4a180c48da115a ("PCI: Remove untested Electromechanical Interlock (EMI) support in pciehp."), which removes the definition of "struct hotplug_slot_attr", broke SGI hotplug driver. By this commit, we get the following compile error. drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr') drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy': drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute' drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register': drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute' This patch fixes this regression by adding the definition of struct hotplug_slot_attr into sgi_hotplug.c. Tested-by: Mike Habeck Signed-off-by: Kenji Kaneshige Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/sgi_hotplug.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c index a4494d78e7c2..0a724bb6ba10 100644 --- a/drivers/pci/hotplug/sgi_hotplug.c +++ b/drivers/pci/hotplug/sgi_hotplug.c @@ -103,6 +103,12 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, return retval; } +struct hotplug_slot_attribute { + struct attribute attr; + ssize_t (*show)(struct hotplug_slot *, char *); + ssize_t (*store)(struct hotplug_slot *, const char *, size_t); +}; + static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path); static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device) -- cgit v1.2.3 From 94f81a47c4a7a2d7a16fcfdd6d81da381732c101 Mon Sep 17 00:00:00 2001 From: Kenji Kaneshige Date: Mon, 27 Jul 2009 12:06:46 +0900 Subject: PCI hotplug: SGI hotplug: do not use hotplug_slot_attr By the pci slot changes, callbacks of attributes under slot directory (/sys/bus/pci/slots) had been changed to get the pointer to struct pci_slot instead of struct hotplug_slot. So the path_show() that assumes the parameter is a pointer to struct hotplug_slot seems broken. Tested-by: Mike Habeck Signed-off-by: Kenji Kaneshige Signed-off-by: Jesse Barnes --- drivers/pci/hotplug/sgi_hotplug.c | 13 +++---------- 1 file changed, 3 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c index 0a724bb6ba10..8aebe1e9d3d6 100644 --- a/drivers/pci/hotplug/sgi_hotplug.c +++ b/drivers/pci/hotplug/sgi_hotplug.c @@ -90,11 +90,10 @@ static struct hotplug_slot_ops sn_hotplug_slot_ops = { static DEFINE_MUTEX(sn_hotplug_mutex); -static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, - char *buf) +static ssize_t path_show(struct pci_slot *pci_slot, char *buf) { int retval = -ENOENT; - struct slot *slot = bss_hotplug_slot->private; + struct slot *slot = pci_slot->hotplug->private; if (!slot) return retval; @@ -103,13 +102,7 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot, return retval; } -struct hotplug_slot_attribute { - struct attribute attr; - ssize_t (*show)(struct hotplug_slot *, char *); - ssize_t (*store)(struct hotplug_slot *, const char *, size_t); -}; - -static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path); +static struct pci_slot_attribute sn_slot_path_attr = __ATTR_RO(path); static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device) { -- cgit v1.2.3 From 2020002a878403a6858868d85a43623f74859dba Mon Sep 17 00:00:00 2001 From: Stoyan Gaydarov Date: Thu, 6 Aug 2009 15:07:28 -0700 Subject: drivers/w1/masters/omap_hdq.c: fix missing mutex unlock This was found using a semantic patch, more info can be found at: http://www.emn.fr/x-info/coccinelle/ Signed-off-by: Stoyan Gaydarov Acked-by: Evgeniy Polyakov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/w1/masters/omap_hdq.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c index a7e3b706b9d3..0d92969404c3 100644 --- a/drivers/w1/masters/omap_hdq.c +++ b/drivers/w1/masters/omap_hdq.c @@ -687,6 +687,7 @@ static int omap_hdq_remove(struct platform_device *pdev) if (hdq_data->hdq_usecount) { dev_dbg(&pdev->dev, "removed when use count is not zero\n"); + mutex_unlock(&hdq_data->hdq_mutex); return -EBUSY; } -- cgit v1.2.3 From 93274e4d4e9416ad1fa47e2f26011e2c483fe5fe Mon Sep 17 00:00:00 2001 From: Stefani Seibold Date: Thu, 6 Aug 2009 15:07:30 -0700 Subject: fbcon: fix rotate upside down crash Fix the rotate_ud() function not to crash in case of a font which has not a width of multiple by 8: The inner loop of the font pixel copy should not access a bit outside the font memory area. Subtract the shift offset from the font width will prevent this. Signed-off-by: Stefani Seibold Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/console/fbcon_rotate.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/video/console/fbcon_rotate.h b/drivers/video/console/fbcon_rotate.h index 75be5ce53dc5..e233444cda66 100644 --- a/drivers/video/console/fbcon_rotate.h +++ b/drivers/video/console/fbcon_rotate.h @@ -45,7 +45,7 @@ static inline void rotate_ud(const char *in, char *out, u32 width, u32 height) width = (width + 7) & ~7; for (i = 0; i < height; i++) { - for (j = 0; j < width; j++) { + for (j = 0; j < width - shift; j++) { if (pattern_test_bit(j, i, width, in)) pattern_set_bit(width - (1 + j + shift), height - (1 + i), -- cgit v1.2.3 From 521594442cc62d1c2af8436a05ab5918b7730b19 Mon Sep 17 00:00:00 2001 From: Florian Tobias Schandinat Date: Thu, 6 Aug 2009 15:07:34 -0700 Subject: viafb: fix rmmod bug This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1) assigned by module_param. It reduces driver complexity by not needlessly changing these vars as they are only read once and removing now superfluous code. On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option used and afterwards unloading it results in: kernel BUG at mm/slub.c:2926! invalid opcode: 0000 [#1] PREEMPT last sysfs file: /sys/devices/virtual/block/loop0/removable Modules linked in: snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm rtl8187 snd_timer eeprom_93cx6 mmc_block snd soundcore via_sdmmc fb snd_page_alloc i2c_algo_bit i2c_viapro ehci_hcd uhci_hcd cfbcopyarea mmc_core cfbimgblt cfbfillrect video output [last unloaded: viafb] Pid: 3355, comm: rmmod Not tainted (2.6.31-rc1 #0) EIP: 0060:[] EFLAGS: 00010246 CPU: 0 EIP is at kfree+0x80/0xda EAX: c17c2da0 EBX: dc7edbdc ECX: 0000010f EDX: 00000000 ESI: c102c700 EDI: dc7ed8fa EBP: d703ff2c ESP: d703ff20 DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 Process rmmod (pid: 3355, ti=d703e000 task=db1412c0 task.ti=d703e000) Stack: dc7edbdc 00000014 00000016 d703ff40 c102c700 dc7f45d4 dc7f45d4 00000880 d703ff4c c103e571 00000000 d703ffac c103e751 66616976 da140062 db89ba80 00000328 d702edf8 db89ba80 d703ff9c c105d0f0 00000200 da14f898 00000014 Call Trace: [] ? destroy_params+0x1e/0x2b [] ? free_module+0xa2/0xd7 [] ? sys_delete_module+0x1ab/0x1da [] ? do_munmap+0x20a/0x225 [] ? sysenter_do_call+0x12/0x26 Code: 10 76 7a 8d 87 00 00 00 40 c1 e8 0c c1 e0 05 03 05 1c 87 41 c1 66 83 38 00 79 03 8b 40 0c 8b 10 84 d2 78 12 66 f7 c2 00 c0 75 04 <0f> 0b eb fe e8 6f 5a fe ff eb 47 8b 55 04 8b 58 0c 9c 5e fa 3b EIP: [] kfree+0x80/0xda SS:ESP 0068:d703ff20 This is caused by the current code changing the pointers assigned by module_param. During unload it tries to free the memory the pointers point at which is now part of an internal structure. The patch simply avoids changing the pointers. This is okay as they are read only once during the initialization process. Signed-off-by: Florian Tobias Schandinat Cc: Scott Fang Cc: Joseph Chan Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/via/hw.c | 4 +- drivers/video/via/lcd.c | 15 ++----- drivers/video/via/viafbdev.c | 101 ++++++++++++++++++++----------------------- drivers/video/via/viafbdev.h | 3 +- 4 files changed, 53 insertions(+), 70 deletions(-) (limited to 'drivers') diff --git a/drivers/video/via/hw.c b/drivers/video/via/hw.c index fcd53ceb88fa..c8960003f47d 100644 --- a/drivers/video/via/hw.c +++ b/drivers/video/via/hw.c @@ -2407,14 +2407,14 @@ int viafb_setmode(int vmode_index, int hor_res, int ver_res, int video_bpp, viafb_dvi_set_mode(viafb_get_mode_index (viaparinfo->tmds_setting_info->h_active, viaparinfo->tmds_setting_info-> - v_active, 1), + v_active), video_bpp1, viaparinfo-> tmds_setting_info->iga_path); } else { viafb_dvi_set_mode(viafb_get_mode_index (viaparinfo->tmds_setting_info->h_active, viaparinfo-> - tmds_setting_info->v_active, 0), + tmds_setting_info->v_active), video_bpp, viaparinfo-> tmds_setting_info->iga_path); } diff --git a/drivers/video/via/lcd.c b/drivers/video/via/lcd.c index 6c7290a6a447..78c6b3387947 100644 --- a/drivers/video/via/lcd.c +++ b/drivers/video/via/lcd.c @@ -580,10 +580,7 @@ static void load_lcd_k400_patch_tbl(int set_hres, int set_vres, int reg_num = 0; struct io_reg *lcd_patch_reg = NULL; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); switch (panel_id) { /* LCD 800x600 */ case LCD_PANEL_ID1_800X600: @@ -761,10 +758,7 @@ static void load_lcd_p880_patch_tbl(int set_hres, int set_vres, int reg_num = 0; struct io_reg *lcd_patch_reg = NULL; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); switch (panel_id) { case LCD_PANEL_ID5_1400X1050: @@ -832,10 +826,7 @@ static void load_lcd_patch_regs(int set_hres, int set_vres, { int vmode_index; - if (viaparinfo->lvds_setting_info->iga_path == IGA2) - vmode_index = viafb_get_mode_index(set_hres, set_vres, 1); - else - vmode_index = viafb_get_mode_index(set_hres, set_vres, 0); + vmode_index = viafb_get_mode_index(set_hres, set_vres); viafb_unlock_crt(); diff --git a/drivers/video/via/viafbdev.c b/drivers/video/via/viafbdev.c index a0fec298216e..72833f3334b5 100644 --- a/drivers/video/via/viafbdev.c +++ b/drivers/video/via/viafbdev.c @@ -32,7 +32,6 @@ static u32 pseudo_pal[17]; /* video mode */ static char *viafb_mode = "640x480"; static char *viafb_mode1 = "640x480"; -static int viafb_resMode = VIA_RES_640X480; /* Added for specifying active devices.*/ char *viafb_active_dev = ""; @@ -56,47 +55,47 @@ static void viafb_get_video_device(u32 *video_dev_info); /* Mode information */ static const struct viafb_modeinfo viafb_modentry[] = { - {480, 640, VIA_RES_480X640, "480x640"}, - {640, 480, VIA_RES_640X480, "640x480"}, - {800, 480, VIA_RES_800X480, "800x480"}, - {800, 600, VIA_RES_800X600, "800x600"}, - {1024, 768, VIA_RES_1024X768, "1024x768"}, - {1152, 864, VIA_RES_1152X864, "1152x864"}, - {1280, 1024, VIA_RES_1280X1024, "1280x1024"}, - {1600, 1200, VIA_RES_1600X1200, "1600x1200"}, - {1440, 1050, VIA_RES_1440X1050, "1440x1050"}, - {1280, 768, VIA_RES_1280X768, "1280x768"}, - {1280, 800, VIA_RES_1280X800, "1280x800"}, - {1280, 960, VIA_RES_1280X960, "1280x960"}, - {1920, 1440, VIA_RES_1920X1440, "1920x1440"}, - {848, 480, VIA_RES_848X480, "848x480"}, - {1400, 1050, VIA_RES_1400X1050, "1400x1050"}, - {720, 480, VIA_RES_720X480, "720x480"}, - {720, 576, VIA_RES_720X576, "720x576"}, - {1024, 512, VIA_RES_1024X512, "1024x512"}, - {1024, 576, VIA_RES_1024X576, "1024x576"}, - {1024, 600, VIA_RES_1024X600, "1024x600"}, - {1280, 720, VIA_RES_1280X720, "1280x720"}, - {1920, 1080, VIA_RES_1920X1080, "1920x1080"}, - {1366, 768, VIA_RES_1368X768, "1368x768"}, - {1680, 1050, VIA_RES_1680X1050, "1680x1050"}, - {960, 600, VIA_RES_960X600, "960x600"}, - {1000, 600, VIA_RES_1000X600, "1000x600"}, - {1024, 576, VIA_RES_1024X576, "1024x576"}, - {1024, 600, VIA_RES_1024X600, "1024x600"}, - {1088, 612, VIA_RES_1088X612, "1088x612"}, - {1152, 720, VIA_RES_1152X720, "1152x720"}, - {1200, 720, VIA_RES_1200X720, "1200x720"}, - {1280, 600, VIA_RES_1280X600, "1280x600"}, - {1360, 768, VIA_RES_1360X768, "1360x768"}, - {1440, 900, VIA_RES_1440X900, "1440x900"}, - {1600, 900, VIA_RES_1600X900, "1600x900"}, - {1600, 1024, VIA_RES_1600X1024, "1600x1024"}, - {1792, 1344, VIA_RES_1792X1344, "1792x1344"}, - {1856, 1392, VIA_RES_1856X1392, "1856x1392"}, - {1920, 1200, VIA_RES_1920X1200, "1920x1200"}, - {2048, 1536, VIA_RES_2048X1536, "2048x1536"}, - {0, 0, VIA_RES_INVALID, "640x480"} + {480, 640, VIA_RES_480X640}, + {640, 480, VIA_RES_640X480}, + {800, 480, VIA_RES_800X480}, + {800, 600, VIA_RES_800X600}, + {1024, 768, VIA_RES_1024X768}, + {1152, 864, VIA_RES_1152X864}, + {1280, 1024, VIA_RES_1280X1024}, + {1600, 1200, VIA_RES_1600X1200}, + {1440, 1050, VIA_RES_1440X1050}, + {1280, 768, VIA_RES_1280X768,}, + {1280, 800, VIA_RES_1280X800}, + {1280, 960, VIA_RES_1280X960}, + {1920, 1440, VIA_RES_1920X1440}, + {848, 480, VIA_RES_848X480}, + {1400, 1050, VIA_RES_1400X1050}, + {720, 480, VIA_RES_720X480}, + {720, 576, VIA_RES_720X576}, + {1024, 512, VIA_RES_1024X512}, + {1024, 576, VIA_RES_1024X576}, + {1024, 600, VIA_RES_1024X600}, + {1280, 720, VIA_RES_1280X720}, + {1920, 1080, VIA_RES_1920X1080}, + {1366, 768, VIA_RES_1368X768}, + {1680, 1050, VIA_RES_1680X1050}, + {960, 600, VIA_RES_960X600}, + {1000, 600, VIA_RES_1000X600}, + {1024, 576, VIA_RES_1024X576}, + {1024, 600, VIA_RES_1024X600}, + {1088, 612, VIA_RES_1088X612}, + {1152, 720, VIA_RES_1152X720}, + {1200, 720, VIA_RES_1200X720}, + {1280, 600, VIA_RES_1280X600}, + {1360, 768, VIA_RES_1360X768}, + {1440, 900, VIA_RES_1440X900}, + {1600, 900, VIA_RES_1600X900}, + {1600, 1024, VIA_RES_1600X1024}, + {1792, 1344, VIA_RES_1792X1344}, + {1856, 1392, VIA_RES_1856X1392}, + {1920, 1200, VIA_RES_1920X1200}, + {2048, 1536, VIA_RES_2048X1536}, + {0, 0, VIA_RES_INVALID} }; static struct fb_ops viafb_ops; @@ -177,7 +176,7 @@ static int viafb_check_var(struct fb_var_screeninfo *var, if (var->vmode & FB_VMODE_INTERLACED || var->vmode & FB_VMODE_DOUBLE) return -EINVAL; - vmode_index = viafb_get_mode_index(var->xres, var->yres, 0); + vmode_index = viafb_get_mode_index(var->xres, var->yres); if (vmode_index == VIA_RES_INVALID) { DEBUG_MSG(KERN_INFO "viafb: Mode %dx%dx%d not supported!!\n", @@ -233,14 +232,14 @@ static int viafb_set_par(struct fb_info *info) viafb_update_device_setting(info->var.xres, info->var.yres, info->var.bits_per_pixel, viafb_refresh, 0); - vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres, 0); + vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres); if (viafb_SAMM_ON == 1) { DEBUG_MSG(KERN_INFO "viafb_second_xres = %d, viafb_second_yres = %d, bpp = %d\n", viafb_second_xres, viafb_second_yres, viafb_bpp1); vmode_index1 = viafb_get_mode_index(viafb_second_xres, - viafb_second_yres, 1); + viafb_second_yres); DEBUG_MSG(KERN_INFO "->viafb_SAMM_ON: index=%d\n", vmode_index1); @@ -1262,7 +1261,7 @@ static int viafb_sync(struct fb_info *info) return 0; } -int viafb_get_mode_index(int hres, int vres, int flag) +int viafb_get_mode_index(int hres, int vres) { u32 i; DEBUG_MSG(KERN_INFO "viafb_get_mode_index!\n"); @@ -1272,13 +1271,7 @@ int viafb_get_mode_index(int hres, int vres, int flag) viafb_modentry[i].yres == vres) break; - viafb_resMode = viafb_modentry[i].mode_index; - if (flag) - viafb_mode1 = viafb_modentry[i].mode_res; - else - viafb_mode = viafb_modentry[i].mode_res; - - return viafb_resMode; + return viafb_modentry[i].mode_index; } static void check_available_device_to_enable(int device_id) @@ -2199,7 +2192,7 @@ static int __devinit via_pci_probe(void) strict_strtoul(tmpc, 0, &default_xres); strict_strtoul(tmpm, 0, &default_yres); - vmode_index = viafb_get_mode_index(default_xres, default_yres, 0); + vmode_index = viafb_get_mode_index(default_xres, default_yres); DEBUG_MSG(KERN_INFO "0->index=%d\n", vmode_index); if (viafb_SAMM_ON == 1) { diff --git a/drivers/video/via/viafbdev.h b/drivers/video/via/viafbdev.h index a4158e872878..227b000feb38 100644 --- a/drivers/video/via/viafbdev.h +++ b/drivers/video/via/viafbdev.h @@ -81,7 +81,6 @@ struct viafb_modeinfo { u32 xres; u32 yres; int mode_index; - char *mode_res; }; extern unsigned int viafb_second_virtual_yres; extern unsigned int viafb_second_virtual_xres; @@ -102,7 +101,7 @@ extern int strict_strtoul(const char *cp, unsigned int base, void viafb_memory_pitch_patch(struct fb_info *info); void viafb_fill_var_timing_info(struct fb_var_screeninfo *var, int refresh, int mode_index); -int viafb_get_mode_index(int hres, int vres, int flag); +int viafb_get_mode_index(int hres, int vres); u8 viafb_gpio_i2c_read_lvds(struct lvds_setting_information *plvds_setting_info, struct lvds_chip_information *plvds_chip_info, u8 index); -- cgit v1.2.3 From 0035fe00f77d2b0a1a2d001f7442136d1ec5aefa Mon Sep 17 00:00:00 2001 From: Johannes Weiner Date: Thu, 6 Aug 2009 15:07:36 -0700 Subject: fbcon: don't use vc_resize() on initialization Catalin and kmemleak spotted a leak of a VC screen buffer in vc_allocate() due to the following chain of events: vc_allocate() visual_init(init=1) vc->vc_sw->con_init(init=1) fbcon_init() vc_resize() vc->screen_buf = kmalloc() vc->screen_buf = kmalloc() The common way for the VC drivers is to set the screen dimension parameters manually in the init case and only call vc_resize() for !init - which allocates a screen buffer according to the new dimensions. fbcon instead would do vc_resize() unconditionally and afterwards set the dimensions manually (again) for !init - i.e. completely upside down. The vc_resize() allocated buffer would then get lost by vc_allocate() allocating a fresh one. Use vc_resize() only for actual resizing to close the leak. Set the dimensions manually only in initialization mode to remove the redundant setting in resize mode. The kmemleak trace from Catalin: unreferenced object 0xde158000 (size 12288): comm "Xorg", pid 1439, jiffies 4294961016 hex dump (first 32 bytes): 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . . 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . . backtrace: [] __save_stack_trace+0x17/0x1c [] create_object+0xcd/0x188 [] kmemleak_alloc+0x1b/0x3c [] __kmalloc+0xdb/0xe8 [] vc_do_resize+0x73/0x1e0 [] vc_resize+0x15/0x18 [] fbcon_init+0x1f9/0x2b8 [] visual_init+0x9f/0xdc [] vc_allocate+0x7f/0xfc [] con_open+0x17/0x80 [] tty_open+0x1f7/0x2e4 [] chrdev_open+0x101/0x118 [] __dentry_open+0x105/0x1cc [] nameidata_to_filp+0x2d/0x38 [] do_filp_open+0x2c1/0x54c [] do_sys_open+0x3b/0xb4 Reported-by: Catalin Marinas Signed-off-by: Johannes Weiner Tested-by: Catalin Marinas Cc: Pekka Enberg Cc: Krzysztof Helt Tested-by: Dave Young Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/console/fbcon.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c index 471a9a60376a..3a44695b9c09 100644 --- a/drivers/video/console/fbcon.c +++ b/drivers/video/console/fbcon.c @@ -1082,7 +1082,6 @@ static void fbcon_init(struct vc_data *vc, int init) new_rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres); new_cols /= vc->vc_font.width; new_rows /= vc->vc_font.height; - vc_resize(vc, new_cols, new_rows); /* * We must always set the mode. The mode of the previous console @@ -1111,10 +1110,11 @@ static void fbcon_init(struct vc_data *vc, int init) * vc_{cols,rows}, but we must not set those if we are only * resizing the console. */ - if (!init) { + if (init) { vc->vc_cols = new_cols; vc->vc_rows = new_rows; - } + } else + vc_resize(vc, new_cols, new_rows); if (logo) fbcon_prepare_logo(vc, info, cols, rows, new_cols, new_rows); -- cgit v1.2.3 From 20de03dae54e10271ffd308654dfb4a117f4789d Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 6 Aug 2009 15:07:40 -0700 Subject: i.MX31: fix framebuffer locking regressions Recent framebuffer locking patches first made affected systems unbootable, then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on mx3 machines doesn't work. Fix this. Signed-off-by: Guennadi Liakhovetski Cc: Sascha Hauer Cc: Krzysztof Helt Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/video/mx3fb.c | 86 +++++++++++++++++++++++++++++++++------------------ 1 file changed, 56 insertions(+), 30 deletions(-) (limited to 'drivers') diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c index f8778cde2183..054ef29be479 100644 --- a/drivers/video/mx3fb.c +++ b/drivers/video/mx3fb.c @@ -669,7 +669,8 @@ static uint32_t bpp_to_pixfmt(int bpp) } static int mx3fb_blank(int blank, struct fb_info *fbi); -static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len); +static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len, + bool lock); static int mx3fb_unmap_video_memory(struct fb_info *fbi); /** @@ -711,12 +712,7 @@ static void mx3fb_dma_done(void *arg) complete(&mx3_fbi->flip_cmpl); } -/** - * mx3fb_set_par() - set framebuffer parameters and change the operating mode. - * @fbi: framebuffer information pointer. - * @return: 0 on success or negative error code on failure. - */ -static int mx3fb_set_par(struct fb_info *fbi) +static int __set_par(struct fb_info *fbi, bool lock) { u32 mem_len; struct ipu_di_signal_cfg sig_cfg; @@ -727,10 +723,6 @@ static int mx3fb_set_par(struct fb_info *fbi) struct idmac_video_param *video = &ichan->params.video; struct scatterlist *sg = mx3_fbi->sg; - dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+'); - - mutex_lock(&mx3_fbi->mutex); - /* Total cleanup */ if (mx3_fbi->txd) sdc_disable_channel(mx3_fbi); @@ -742,10 +734,8 @@ static int mx3fb_set_par(struct fb_info *fbi) if (fbi->fix.smem_start) mx3fb_unmap_video_memory(fbi); - if (mx3fb_map_video_memory(fbi, mem_len) < 0) { - mutex_unlock(&mx3_fbi->mutex); + if (mx3fb_map_video_memory(fbi, mem_len, lock) < 0) return -ENOMEM; - } } sg_init_table(&sg[0], 1); @@ -791,7 +781,6 @@ static int mx3fb_set_par(struct fb_info *fbi) fbi->var.vsync_len, fbi->var.lower_margin + fbi->var.vsync_len, sig_cfg) != 0) { - mutex_unlock(&mx3_fbi->mutex); dev_err(fbi->device, "mx3fb: Error initializing panel.\n"); return -EINVAL; @@ -810,9 +799,30 @@ static int mx3fb_set_par(struct fb_info *fbi) if (mx3_fbi->blank == FB_BLANK_UNBLANK) sdc_enable_channel(mx3_fbi); + return 0; +} + +/** + * mx3fb_set_par() - set framebuffer parameters and change the operating mode. + * @fbi: framebuffer information pointer. + * @return: 0 on success or negative error code on failure. + */ +static int mx3fb_set_par(struct fb_info *fbi) +{ + struct mx3fb_info *mx3_fbi = fbi->par; + struct mx3fb_data *mx3fb = mx3_fbi->mx3fb; + struct idmac_channel *ichan = mx3_fbi->idmac_channel; + int ret; + + dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+'); + + mutex_lock(&mx3_fbi->mutex); + + ret = __set_par(fbi, true); + mutex_unlock(&mx3_fbi->mutex); - return 0; + return ret; } /** @@ -966,21 +976,11 @@ static int mx3fb_setcolreg(unsigned int regno, unsigned int red, return ret; } -/** - * mx3fb_blank() - blank the display. - */ -static int mx3fb_blank(int blank, struct fb_info *fbi) +static void __blank(int blank, struct fb_info *fbi) { struct mx3fb_info *mx3_fbi = fbi->par; struct mx3fb_data *mx3fb = mx3_fbi->mx3fb; - dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__, - blank, fbi->screen_base, fbi->fix.smem_len); - - if (mx3_fbi->blank == blank) - return 0; - - mutex_lock(&mx3_fbi->mutex); mx3_fbi->blank = blank; switch (blank) { @@ -999,6 +999,23 @@ static int mx3fb_blank(int blank, struct fb_info *fbi) sdc_set_brightness(mx3fb, mx3fb->backlight_level); break; } +} + +/** + * mx3fb_blank() - blank the display. + */ +static int mx3fb_blank(int blank, struct fb_info *fbi) +{ + struct mx3fb_info *mx3_fbi = fbi->par; + + dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__, + blank, fbi->screen_base, fbi->fix.smem_len); + + if (mx3_fbi->blank == blank) + return 0; + + mutex_lock(&mx3_fbi->mutex); + __blank(blank, fbi); mutex_unlock(&mx3_fbi->mutex); return 0; @@ -1198,6 +1215,7 @@ static int mx3fb_resume(struct platform_device *pdev) * mx3fb_map_video_memory() - allocates the DRAM memory for the frame buffer. * @fbi: framebuffer information pointer * @mem_len: length of mapped memory + * @lock: do not lock during initialisation * @return: Error code indicating success or failure * * This buffer is remapped into a non-cached, non-buffered, memory region to @@ -1205,7 +1223,8 @@ static int mx3fb_resume(struct platform_device *pdev) * area is remapped, all virtual memory access to the video memory should occur * at the new region. */ -static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len) +static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len, + bool lock) { int retval = 0; dma_addr_t addr; @@ -1221,10 +1240,12 @@ static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len) goto err0; } - mutex_lock(&fbi->mm_lock); + if (lock) + mutex_lock(&fbi->mm_lock); fbi->fix.smem_start = addr; fbi->fix.smem_len = mem_len; - mutex_unlock(&fbi->mm_lock); + if (lock) + mutex_unlock(&fbi->mm_lock); dev_dbg(fbi->device, "allocated fb @ p=0x%08x, v=0x%p, size=%d.\n", (uint32_t) fbi->fix.smem_start, fbi->screen_base, fbi->fix.smem_len); @@ -1365,6 +1386,11 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan) init_completion(&mx3fbi->flip_cmpl); disable_irq(ichan->eof_irq); dev_dbg(mx3fb->dev, "disabling irq %d\n", ichan->eof_irq); + ret = __set_par(fbi, false); + if (ret < 0) + goto esetpar; + + __blank(FB_BLANK_UNBLANK, fbi); dev_info(dev, "registered, using mode %s\n", fb_mode); -- cgit v1.2.3 From 2198a64a7487aba036f71998ade8a6528070d32c Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Thu, 6 Aug 2009 15:07:41 -0700 Subject: drivers/mmc: correct error-handling code sdhci_alloc_host returns an ERR_PTR value in an error case instead of NULL. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // @match exists@ expression x, E; statement S1, S2; @@ x = sdhci_alloc_host(...) ... when != x = E ( * if (x == NULL || ...) S1 else S2 | * if (x == NULL && ...) S1 else S2 ) // Signed-off-by: Julia Lawall Acked-by: Anton Vorontsov Cc: Matt Fleming Cc: Ian Molton Cc: "Roberto A. Foglietta" Cc: Philip Langdale Cc: Pierre Ossman Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/mmc/host/sdhci-of.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c index 908844327db0..1e8aa590bb39 100644 --- a/drivers/mmc/host/sdhci-of.c +++ b/drivers/mmc/host/sdhci-of.c @@ -234,7 +234,7 @@ static int __devinit sdhci_of_probe(struct of_device *ofdev, return -ENODEV; host = sdhci_alloc_host(&ofdev->dev, sizeof(*of_host)); - if (!host) + if (IS_ERR(host)) return -ENOMEM; of_host = sdhci_priv(host); -- cgit v1.2.3 From 49276560c9004fce24c42e3c0ad75f34d956fc63 Mon Sep 17 00:00:00 2001 From: Khanh-Dang Nguyen Thu Lam Date: Tue, 28 Jul 2009 19:41:17 +0200 Subject: USB: pl2303: New vendor and product id I am submitting a patch for the pl2303 driver. This patch adds support for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437). This USB cable is a so-called data cable used to connect a Sony mobile phone to a computer. Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and Z7. I have used this patch with my Sony CMD-J70 for several days and I haven't encountered any kernel/hardware issue. From: Khanh-Dang Nguyen Thu Lam Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 + drivers/usb/serial/pl2303.h | 4 ++++ 2 files changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 7d15bfa7c2db..3e86815b2705 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -95,6 +95,7 @@ static struct usb_device_id id_table [] = { { USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) }, { USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) }, { USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) }, + { USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) }, { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 12aac7d2462d..ee9505e1dd92 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -126,3 +126,7 @@ /* Cressi Edy (diving computer) PC interface */ #define CRESSI_VENDOR_ID 0x04b8 #define CRESSI_EDY_PRODUCT_ID 0x0521 + +/* Sony, USB data cable for CMD-Jxx mobile phones */ +#define SONY_VENDOR_ID 0x054c +#define SONY_QN3USB_PRODUCT_ID 0x0437 -- cgit v1.2.3 From 18753ebc8a98efe0e8ff6167afb31cef220c8e50 Mon Sep 17 00:00:00 2001 From: Michael Buesch Date: Wed, 29 Jul 2009 11:39:03 +0200 Subject: USB: devio: Properly do access_ok() checks access_ok() checks must be done on every part of the userspace structure that is accessed. If access_ok() on one part of the struct succeeded, it does not imply it will succeed on other parts of the struct. (Does depend on the architecture implementation of access_ok()). This changes the __get_user() users to first check access_ok() on the data structure. Signed-off-by: Michael Buesch Cc: stable Cc: Pete Zaitcev Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 38b8bce782d6..e192fa05f8a1 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -1321,7 +1321,8 @@ static int get_urb32(struct usbdevfs_urb *kurb, struct usbdevfs_urb32 __user *uurb) { __u32 uptr; - if (get_user(kurb->type, &uurb->type) || + if (!access_ok(VERIFY_READ, uurb, sizeof(*uurb)) || + __get_user(kurb->type, &uurb->type) || __get_user(kurb->endpoint, &uurb->endpoint) || __get_user(kurb->status, &uurb->status) || __get_user(kurb->flags, &uurb->flags) || @@ -1536,8 +1537,9 @@ static int proc_ioctl_compat(struct dev_state *ps, compat_uptr_t arg) u32 udata; uioc = compat_ptr((long)arg); - if (get_user(ctrl.ifno, &uioc->ifno) || - get_user(ctrl.ioctl_code, &uioc->ioctl_code) || + if (!access_ok(VERIFY_READ, uioc, sizeof(*uioc)) || + __get_user(ctrl.ifno, &uioc->ifno) || + __get_user(ctrl.ioctl_code, &uioc->ioctl_code) || __get_user(udata, &uioc->data)) return -EFAULT; ctrl.data = compat_ptr(udata); -- cgit v1.2.3 From e8e2ff462dd92693f29eb848f42d3eb720390d59 Mon Sep 17 00:00:00 2001 From: "Gupta, Ajay Kumar" Date: Wed, 29 Jul 2009 11:58:57 +0530 Subject: USB: musb: fix the nop registration for OMAP3EVM OMAP3EVM uses ISP1504 phy which doesn't require any programming and thus has to use NOP otg transceiver. Cleanups being done: - Remove unwanted code in usb-musb.c file - Register NOP in OMAP3EVM board file using usb_nop_xceiv_register(). - Select NOP_USB_XCEIV for OMAP3EVM boards. - Don't enable TWL4030_USB in omap3_evm_defconfig Signed-off-by: Ajay Kumar Gupta Signed-off-by: Eino-Ville Talvala Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- arch/arm/configs/omap3_evm_defconfig | 2 +- arch/arm/mach-omap2/board-omap3evm.c | 5 +++++ arch/arm/mach-omap2/usb-musb.c | 21 --------------------- drivers/usb/musb/Kconfig | 1 + 4 files changed, 7 insertions(+), 22 deletions(-) (limited to 'drivers') diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig index 28be17fbc157..d5ff4776cd0a 100644 --- a/arch/arm/configs/omap3_evm_defconfig +++ b/arch/arm/configs/omap3_evm_defconfig @@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set -CONFIG_TWL4030_USB=y +# CONFIG_TWL4030_USB is not set # CONFIG_NOP_USB_XCEIV is not set CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d0..cf3dd771a678 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include @@ -307,6 +308,10 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info)); omap_serial_init(); +#ifdef CONFIG_NOP_USB_XCEIV + /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ + usb_nop_xceiv_register(); +#endif usb_musb_init(); ads7846_dev_init(); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index d85296dc896c..739e59e8025c 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -155,20 +155,6 @@ static struct platform_device musb_device = { .resource = musb_resources, }; -#ifdef CONFIG_NOP_USB_XCEIV -static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32); - -static struct platform_device nop_xceiv_device = { - .name = "nop_usb_xceiv", - .id = -1, - .dev = { - .dma_mask = &nop_xceiv_dmamask, - .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = NULL, - }, -}; -#endif - void __init usb_musb_init(void) { if (cpu_is_omap243x()) @@ -183,13 +169,6 @@ void __init usb_musb_init(void) */ musb_plat.clock = "ick"; -#ifdef CONFIG_NOP_USB_XCEIV - if (platform_device_register(&nop_xceiv_device) < 0) { - printk(KERN_ERR "Unable to register NOP-XCEIV device\n"); - return; - } -#endif - if (platform_device_register(&musb_device) < 0) { printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n"); return; diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 70073b157f0a..803adcb5ac1d 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -12,6 +12,7 @@ config USB_MUSB_HDRC depends on !SUPERH select NOP_USB_XCEIV if ARCH_DAVINCI select TWL4030_USB if MACH_OMAP_3430SDP + select NOP_USB_XCEIV if MACH_OMAP3EVM select USB_OTG_UTILS tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' help -- cgit v1.2.3 From 01105a246345f011fde64d24a601090b646e9e4c Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 30 Jul 2009 15:28:14 -0400 Subject: USB: usbfs: fix -ENOENT error code to be -ENODEV This patch (as1272) changes the error code returned when an open call for a USB device node fails to locate the corresponding device. The appropriate error code is -ENODEV, not -ENOENT. Signed-off-by: Alan Stern CC: Kay Sievers Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index e192fa05f8a1..4247eccf858c 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -595,7 +595,7 @@ static int usbdev_open(struct inode *inode, struct file *file) if (!ps) goto out; - ret = -ENOENT; + ret = -ENODEV; /* usbdev device-node */ if (imajor(inode) == USB_DEVICE_MAJOR) -- cgit v1.2.3 From 7a0f0d951273eee889c2441846842348ebc00a2a Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 31 Jul 2009 10:40:22 -0400 Subject: USB: EHCI: fix two new bugs related to Clear-TT-Buffer This patch (as1273) fixes two(!) bugs introduced by the new Clear-TT-Buffer implementation in ehci-hcd. It is now possible for an idle QH to have some URBs on its queue -- this will happen if a Clear-TT-Buffer is pending for the QH's endpoint. Consequently we should not issue a warning when someone tries to unlink an URB from an idle QH; instead we should process the request immediately. The refcounts for QHs could get messed up, because submit_async() would increment the refcount when calling qh_link_async() and qh_link_async() would then refuse to link the QH into the schedule if a Clear-TT-Buffer was pending. Instead we should increment the refcount only when the QH actually is added to the schedule. The current code tries to be clever by leaving the refcount alone if an unlink is immediately followed by a relink; the patch changes this to an unconditional decrement and increment (although they occur in the opposite order). Signed-off-by: Alan Stern CC: David Brownell Tested-by: Manuel Lauss Tested-by: Matthijs Kooijman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 3 ++- drivers/usb/host/ehci-q.c | 6 +++--- 2 files changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 7d03549c3339..11c627ce6022 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -903,7 +903,8 @@ static int ehci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) /* already started */ break; case QH_STATE_IDLE: - WARN_ON(1); + /* QH might be waiting for a Clear-TT-Buffer */ + qh_completions(ehci, qh); break; } break; diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index 9a1384747f3b..b27380505576 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -940,6 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh) head->qh_next.qh = qh; head->hw_next = dma; + qh_get(qh); qh->xacterrs = QH_XACTERR_MAX; qh->qh_state = QH_STATE_LINKED; /* qtd completions reported later by interrupt */ @@ -1080,7 +1081,7 @@ submit_async ( * the HC and TT handle it when the TT has a buffer ready. */ if (likely (qh->qh_state == QH_STATE_IDLE)) - qh_link_async (ehci, qh_get (qh)); + qh_link_async(ehci, qh); done: spin_unlock_irqrestore (&ehci->lock, flags); if (unlikely (qh == NULL)) @@ -1115,8 +1116,6 @@ static void end_unlink_async (struct ehci_hcd *ehci) && HC_IS_RUNNING (ehci_to_hcd(ehci)->state)) qh_link_async (ehci, qh); else { - qh_put (qh); // refcount from async list - /* it's not free to turn the async schedule on/off; leave it * active but idle for a while once it empties. */ @@ -1124,6 +1123,7 @@ static void end_unlink_async (struct ehci_hcd *ehci) && ehci->async->qh_next.qh == NULL) timer_action (ehci, TIMER_ASYNC_OFF); } + qh_put(qh); /* refcount from async list */ if (next) { ehci->reclaim = NULL; -- cgit v1.2.3 From ef4638f955f2c4a667c8af20769d03f5ed3781ca Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 31 Jul 2009 10:41:40 -0400 Subject: USB: EHCI: fix counting of transaction error retries This patch (as1274) simplifies the counting of transaction-error retries. Now we will count up from 0 to QH_XACTERR_MAX instead of down from QH_XACTERR_MAX to 0. The patch also fixes a small bug: qh->xacterr was not getting initialized for interrupt endpoints. Signed-off-by: Alan Stern Tested-by: Matthijs Kooijman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-q.c | 9 ++++----- drivers/usb/host/ehci-sched.c | 1 + 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index b27380505576..7673554fa64d 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -375,12 +375,11 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh) */ if ((token & QTD_STS_XACT) && QTD_CERR(token) == 0 && - --qh->xacterrs > 0 && + ++qh->xacterrs < QH_XACTERR_MAX && !urb->unlinked) { ehci_dbg(ehci, "detected XactErr len %zu/%zu retry %d\n", - qtd->length - QTD_LENGTH(token), qtd->length, - QH_XACTERR_MAX - qh->xacterrs); + qtd->length - QTD_LENGTH(token), qtd->length, qh->xacterrs); /* reset the token in the qtd and the * qh overlay (which still contains @@ -494,7 +493,7 @@ halt: last = qtd; /* reinit the xacterr counter for the next qtd */ - qh->xacterrs = QH_XACTERR_MAX; + qh->xacterrs = 0; } /* last urb's completion might still need calling */ @@ -941,7 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh) head->hw_next = dma; qh_get(qh); - qh->xacterrs = QH_XACTERR_MAX; + qh->xacterrs = 0; qh->qh_state = QH_STATE_LINKED; /* qtd completions reported later by interrupt */ } diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c index 74f7f83b29ad..edd61ee90323 100644 --- a/drivers/usb/host/ehci-sched.c +++ b/drivers/usb/host/ehci-sched.c @@ -542,6 +542,7 @@ static int qh_link_periodic (struct ehci_hcd *ehci, struct ehci_qh *qh) } } qh->qh_state = QH_STATE_LINKED; + qh->xacterrs = 0; qh_get (qh); /* update per-qh bandwidth for usbfs */ -- cgit v1.2.3 From c47aacc67a3d26dfab9c9b8965975ed2b2010b30 Mon Sep 17 00:00:00 2001 From: Marko Hänninen Date: Fri, 31 Jul 2009 22:32:39 +0300 Subject: USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial converter cable MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Attached patch adds USB vendor and product IDs for Bayer's USB to serial converter cable used by Bayer blood glucose meters. It seems to be a FT232RL based device and works without any problem with ftdi_sio driver when this patch is applied. See: http://winglucofacts.com/cables/ Signed-off-by: Marko Hänninen Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index b574878c78b2..500087ea58a5 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -699,6 +699,7 @@ static struct usb_device_id id_table_combined [] = { .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, + { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index 24dbd99e87d7..f203b2a51302 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -953,6 +953,13 @@ #define GN_OTOMETRICS_VID 0x0c33 /* Vendor ID */ #define AURICAL_USB_PID 0x0010 /* Aurical USB Audiometer */ +/* + * Bayer Ascensia Contour blood glucose meter USB-converter cable. + * http://winglucofacts.com/cables/ + */ +#define BAYER_VID 0x1A79 +#define BAYER_CONTOUR_CABLE_PID 0x6001 + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- cgit v1.2.3 From 50d0678e2026c18e4147f0b16b5853113659b82d Mon Sep 17 00:00:00 2001 From: Dhaval Vasa Date: Fri, 7 Aug 2009 17:26:49 +0530 Subject: USB: ftdi_sio: add product_id for Marvell OpenRD Base, Client reference: http://www.open-rd.org Signed-off-by: Dhaval Vasa Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 2 ++ drivers/usb/serial/ftdi_sio.h | 7 +++++++ 2 files changed, 9 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 500087ea58a5..8fec5d4455c9 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -700,6 +700,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) }, { USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) }, { USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) }, + { USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index f203b2a51302..8c92b88166ae 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -960,6 +960,13 @@ #define BAYER_VID 0x1A79 #define BAYER_CONTOUR_CABLE_PID 0x6001 +/* + * Marvell OpenRD Base, Client + * http://www.open-rd.org + * OpenRD Base, Client use VID 0x0403 + */ +#define MARVELL_OPENRD_PID 0x9e90 + /* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ -- cgit v1.2.3 From c15e3ca1d822abba78c00b1ffc3e7b382a50396e Mon Sep 17 00:00:00 2001 From: Rogerio Brito Date: Thu, 6 Aug 2009 15:20:19 -0700 Subject: USB: storage: include Prolific Technology USB drive in unusual_devs list Add a quirk entry for the Leading Driver UD-11 usb flash drive. As Alan Stern told me, the device doesn't deal correctly with the locking media feature of the device, and this patch incorporates it. Compiled, tested, working. Signed-off-by: Rogerio Brito Cc: Phil Dibowitz Cc: Alan Stern Cc: Robert Hancock Cc: stable Signed-off-by: Andrew Morton Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 1b9c5dd0fb27..7477d411959f 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -838,6 +838,13 @@ UNUSUAL_DEV( 0x066f, 0x8000, 0x0001, 0x0001, US_SC_DEVICE, US_PR_DEVICE, NULL, US_FL_FIX_CAPACITY ), +/* Reported by Rogerio Brito */ +UNUSUAL_DEV( 0x067b, 0x2317, 0x0001, 0x001, + "Prolific Technology, Inc.", + "Mass Storage Device", + US_SC_DEVICE, US_PR_DEVICE, NULL, + US_FL_NOT_LOCKABLE ), + /* Reported by Richard -=[]=- */ /* Change to bcdDeviceMin (0x0100 to 0x0001) reported by * Thomas Bartosik */ -- cgit v1.2.3 From cf7fdd57f978d40ceb9a0f58a25f5cf9c84d6f33 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Tue, 4 Aug 2009 23:52:09 +0200 Subject: USB: fix oops on disconnect in cdc-acm This patch fixes an oops caused when during an unplug a device's table of endpoints is zeroed before the driver is notified. A pointer to the endpoint must be cached. this fixes a regression caused by commit 5186ffee2320942c3dc9745f7930e0eb15329ca6 Therefore it should go into 2.6.31 Signed-off-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 10 +++++----- drivers/usb/class/cdc-acm.h | 2 ++ 2 files changed, 7 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index e1f89416ef8c..2bfc41ece0e1 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -387,7 +387,6 @@ static void acm_rx_tasklet(unsigned long _acm) struct acm_ru *rcv; unsigned long flags; unsigned char throttled; - struct usb_host_endpoint *ep; dbg("Entering acm_rx_tasklet"); @@ -463,14 +462,12 @@ urbs: rcv->buffer = buf; - ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in : acm->dev->ep_out) - [usb_pipeendpoint(acm->rx_endpoint)]; - if (usb_endpoint_xfer_int(&ep->desc)) + if (acm->is_int_ep) usb_fill_int_urb(rcv->urb, acm->dev, acm->rx_endpoint, buf->base, acm->readsize, - acm_read_bulk, rcv, ep->desc.bInterval); + acm_read_bulk, rcv, acm->bInterval); else usb_fill_bulk_urb(rcv->urb, acm->dev, acm->rx_endpoint, @@ -1183,6 +1180,9 @@ made_compressed_probe: spin_lock_init(&acm->read_lock); mutex_init(&acm->mutex); acm->rx_endpoint = usb_rcvbulkpipe(usb_dev, epread->bEndpointAddress); + acm->is_int_ep = usb_endpoint_xfer_int(epread); + if (acm->is_int_ep) + acm->bInterval = epread->bInterval; tty_port_init(&acm->port); acm->port.ops = &acm_port_ops; diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h index 1602324808ba..c4a0ee8ffccf 100644 --- a/drivers/usb/class/cdc-acm.h +++ b/drivers/usb/class/cdc-acm.h @@ -126,6 +126,8 @@ struct acm { unsigned int ctrl_caps; /* control capabilities from the class specific header */ unsigned int susp_count; /* number of suspended interfaces */ int combined_interfaces:1; /* control and data collapsed */ + int is_int_ep:1; /* interrupt endpoints contrary to spec used */ + u8 bInterval; struct acm_wb *delayed_wb; /* write queued for a device about to be woken */ }; -- cgit v1.2.3 From 4d2da07bc876fc5bc455e0721df388a3db7e4ba5 Mon Sep 17 00:00:00 2001 From: Jakob Gruber Date: Thu, 30 Jul 2009 20:37:36 +0200 Subject: Staging: rt2870: Add USB ID for Linksys, Planex Communications, Belkin Linksys WUSB100, Belkin F5D8053 N, Planex Communications unknown model. Signed-off-by: Jakob Gruber Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rt2870/rt2870.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h index 29e3b53e52a1..10e1640d61e5 100644 --- a/drivers/staging/rt2870/rt2870.h +++ b/drivers/staging/rt2870/rt2870.h @@ -79,6 +79,7 @@ { \ {USB_DEVICE(0x148F,0x2770)}, /* Ralink */ \ {USB_DEVICE(0x1737,0x0071)}, /* Linksys WUSB600N */ \ + {USB_DEVICE(0x1737,0x0070)}, /* Linksys */ \ {USB_DEVICE(0x148F,0x2870)}, /* Ralink */ \ {USB_DEVICE(0x148F,0x3070)}, /* Ralink */ \ {USB_DEVICE(0x0B05,0x1731)}, /* Asus */ \ @@ -93,12 +94,14 @@ {USB_DEVICE(0x14B2,0x3C06)}, /* Conceptronic */ \ {USB_DEVICE(0x14B2,0x3C28)}, /* Conceptronic */ \ {USB_DEVICE(0x2019,0xED06)}, /* Planex Communications, Inc. */ \ + {USB_DEVICE(0x2019,0xED14)}, /* Planex Communications, Inc. */ \ {USB_DEVICE(0x2019,0xAB25)}, /* Planex Communications, Inc. RT3070 */ \ {USB_DEVICE(0x07D1,0x3C09)}, /* D-Link */ \ {USB_DEVICE(0x07D1,0x3C11)}, /* D-Link */ \ {USB_DEVICE(0x14B2,0x3C07)}, /* AL */ \ {USB_DEVICE(0x14B2,0x3C12)}, /* AL */ \ {USB_DEVICE(0x050D,0x8053)}, /* Belkin */ \ + {USB_DEVICE(0x050D,0x815C)}, /* Belkin */ \ {USB_DEVICE(0x14B2,0x3C23)}, /* Airlink */ \ {USB_DEVICE(0x14B2,0x3C27)}, /* Airlink */ \ {USB_DEVICE(0x07AA,0x002F)}, /* Corega */ \ -- cgit v1.2.3 From 2c63abf9e8a51dec886da482dfd8ae752581a61c Mon Sep 17 00:00:00 2001 From: Mike Galbraith Date: Fri, 31 Jul 2009 07:14:04 +0200 Subject: Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API The sanity check this patch introduced triggers on shutdown, apparently due to threads having already exited by the time BUG_ON() is reached. Signed-off-by: Mike Galbraith Cc: Peter Teoh Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rt2860/rt_linux.h | 13 ++--- drivers/staging/rt2870/2870_main_dev.c | 67 +++++++++++++++++--------- drivers/staging/rt2870/common/2870_rtmp_init.c | 33 ++++++------- drivers/staging/rt2870/common/rtusb_io.c | 3 +- drivers/staging/rt2870/rt2870.h | 6 +-- 5 files changed, 68 insertions(+), 54 deletions(-) (limited to 'drivers') diff --git a/drivers/staging/rt2860/rt_linux.h b/drivers/staging/rt2860/rt_linux.h index 85175c182432..25b53ac3f820 100644 --- a/drivers/staging/rt2860/rt_linux.h +++ b/drivers/staging/rt2860/rt_linux.h @@ -43,9 +43,6 @@ #include "rtmp_type.h" #include #include -#if !defined(RT2860) && !defined(RT30xx) -#include -#endif #include #include @@ -166,9 +163,7 @@ typedef int (*HARD_START_XMIT_FUNC)(struct sk_buff *skb, struct net_device *net_ #ifndef RT30xx typedef struct pid * THREAD_PID; -#ifdef RT2860 #define THREAD_PID_INIT_VALUE NULL -#endif #define GET_PID(_v) find_get_pid(_v) #define GET_PID_NUMBER(_v) pid_nr(_v) #define CHECK_PID_LEGALITY(_pid) if (pid_nr(_pid) >= 0) @@ -188,12 +183,12 @@ struct os_cookie { dma_addr_t pAd_pa; #endif #ifdef RT2870 - struct usb_device *pUsb_Dev; + struct usb_device *pUsb_Dev; #ifndef RT30xx - struct task_struct *MLMEThr_task; - struct task_struct *RTUSBCmdThr_task; - struct task_struct *TimerQThr_task; + THREAD_PID MLMEThr_pid; + THREAD_PID RTUSBCmdThr_pid; + THREAD_PID TimerQThr_pid; #endif #ifdef RT30xx struct pid *MLMEThr_pid; diff --git a/drivers/staging/rt2870/2870_main_dev.c b/drivers/staging/rt2870/2870_main_dev.c index dd01c64fbf61..a4e8696ca39c 100644 --- a/drivers/staging/rt2870/2870_main_dev.c +++ b/drivers/staging/rt2870/2870_main_dev.c @@ -235,7 +235,7 @@ INT MlmeThread( DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__)); #ifndef RT30xx - pObj->MLMEThr_task = NULL; + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -348,7 +348,7 @@ INT RTUSBCmdThread( DBGPRINT(RT_DEBUG_TRACE,( "<---RTUSBCmdThread\n")); #ifndef RT30xx - pObj->RTUSBCmdThr_task = NULL; + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = NULL; @@ -447,7 +447,7 @@ INT TimerQThread( DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__)); #ifndef RT30xx - pObj->TimerQThr_task = NULL; + pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->TimerQThr_pid = NULL; @@ -883,46 +883,69 @@ VOID RT28xxThreadTerminate( // Terminate Threads #ifndef RT30xx - BUG_ON(pObj->TimerQThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->TimerQThr_task)) + CHECK_PID_LEGALITY(pObj->TimerQThr_pid) { POS_COOKIE pObj = (POS_COOKIE)pAd->OS_Cookie; - printk(KERN_DEBUG "Terminate the TimerQThr pid=%d!\n", - pid_nr(task_pid(pObj->TimerQThr_task))); + printk("Terminate the TimerQThr_pid=%d!\n", GET_PID_NUMBER(pObj->TimerQThr_pid)); mb(); pAd->TimerFunc_kill = 1; mb(); - kthread_stop(pObj->TimerQThr_task); - pObj->TimerQThr_task = NULL; + ret = KILL_THREAD_PID(pObj->TimerQThr_pid, SIGTERM, 1); + if (ret) + { + printk(KERN_WARNING "%s: unable to stop TimerQThread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->TimerQThr_pid), ret); + } + else + { + wait_for_completion(&pAd->TimerQComplete); + pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE; + } } - BUG_ON(pObj->MLMEThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task)) + CHECK_PID_LEGALITY(pObj->MLMEThr_pid) { - printk(KERN_DEBUG "Terminate the MLMEThr pid=%d!\n", - pid_nr(task_pid(pObj->MLMEThr_task))); + printk("Terminate the MLMEThr_pid=%d!\n", GET_PID_NUMBER(pObj->MLMEThr_pid)); mb(); pAd->mlme_kill = 1; //RT28XX_MLME_HANDLER(pAd); mb(); - kthread_stop(pObj->MLMEThr_task); - pObj->MLMEThr_task = NULL; + ret = KILL_THREAD_PID(pObj->MLMEThr_pid, SIGTERM, 1); + if (ret) + { + printk (KERN_WARNING "%s: unable to Mlme thread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->MLMEThr_pid), ret); + } + else + { + //wait_for_completion (&pAd->notify); + wait_for_completion (&pAd->mlmeComplete); + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; + } } - BUG_ON(pObj->RTUSBCmdThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) { - printk(KERN_DEBUG "Terminate the RTUSBCmdThr pid=%d!\n", - pid_nr(task_pid(pObj->RTUSBCmdThr_task))); + printk("Terminate the RTUSBCmdThr_pid=%d!\n", GET_PID_NUMBER(pObj->RTUSBCmdThr_pid)); mb(); NdisAcquireSpinLock(&pAd->CmdQLock); pAd->CmdQ.CmdQState = RT2870_THREAD_STOPED; NdisReleaseSpinLock(&pAd->CmdQLock); mb(); //RTUSBCMDUp(pAd); - kthread_stop(pObj->RTUSBCmdThr_task); - pObj->RTUSBCmdThr_task = NULL; + ret = KILL_THREAD_PID(pObj->RTUSBCmdThr_pid, SIGTERM, 1); + if (ret) + { + printk(KERN_WARNING "%s: unable to RTUSBCmd thread, pid=%d, ret=%d!\n", + pAd->net_dev->name, GET_PID_NUMBER(pObj->RTUSBCmdThr_pid), ret); + } + else + { + //wait_for_completion (&pAd->notify); + wait_for_completion (&pAd->CmdQComplete); + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; + } } #endif #ifdef RT30xx @@ -1045,7 +1068,7 @@ BOOLEAN RT28XXChipsetCheck( dev_p->descriptor.idProduct == rtusb_usb_id[i].idProduct) { #ifndef RT30xx - printk(KERN_DEBUG "rt2870: idVendor = 0x%x, idProduct = 0x%x\n", + printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n", #endif #ifdef RT30xx printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n", diff --git a/drivers/staging/rt2870/common/2870_rtmp_init.c b/drivers/staging/rt2870/common/2870_rtmp_init.c index 0f4c8af97e47..80909e9ab5ae 100644 --- a/drivers/staging/rt2870/common/2870_rtmp_init.c +++ b/drivers/staging/rt2870/common/2870_rtmp_init.c @@ -700,8 +700,8 @@ NDIS_STATUS AdapterBlockAllocateMemory( usb_dev = pObj->pUsb_Dev; #ifndef RT30xx - pObj->MLMEThr_task = NULL; - pObj->RTUSBCmdThr_task = NULL; + pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE; + pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE; #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -743,7 +743,7 @@ NDIS_STATUS CreateThreads( PRTMP_ADAPTER pAd = net_dev->ml_priv; POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; #ifndef RT30xx - struct task_struct *tsk; + pid_t pid_number = -1; #endif #ifdef RT30xx pid_t pid_number; @@ -762,10 +762,10 @@ NDIS_STATUS CreateThreads( // Creat MLME Thread #ifndef RT30xx - pObj->MLMEThr_task = NULL; - tsk = kthread_run(MlmeThread, pAd, "%s", pAd->net_dev->name); - - if (IS_ERR(tsk)) { + pObj->MLMEThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(MlmeThread, pAd, CLONE_VM); + if (pid_number < 0) + { #endif #ifdef RT30xx pObj->MLMEThr_pid = NULL; @@ -778,7 +778,7 @@ NDIS_STATUS CreateThreads( } #ifndef RT30xx - pObj->MLMEThr_task = tsk; + pObj->MLMEThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->MLMEThr_pid = find_get_pid(pid_number); @@ -788,10 +788,9 @@ NDIS_STATUS CreateThreads( // Creat Command Thread #ifndef RT30xx - pObj->RTUSBCmdThr_task = NULL; - tsk = kthread_run(RTUSBCmdThread, pAd, "%s", pAd->net_dev->name); - - if (IS_ERR(tsk) < 0) + pObj->RTUSBCmdThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(RTUSBCmdThread, pAd, CLONE_VM); + if (pid_number < 0) #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = NULL; @@ -804,7 +803,7 @@ NDIS_STATUS CreateThreads( } #ifndef RT30xx - pObj->RTUSBCmdThr_task = tsk; + pObj->RTUSBCmdThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->RTUSBCmdThr_pid = find_get_pid(pid_number); @@ -812,9 +811,9 @@ NDIS_STATUS CreateThreads( wait_for_completion(&(pAd->CmdQComplete)); #ifndef RT30xx - pObj->TimerQThr_task = NULL; - tsk = kthread_run(TimerQThread, pAd, "%s", pAd->net_dev->name); - if (IS_ERR(tsk) < 0) + pObj->TimerQThr_pid= THREAD_PID_INIT_VALUE; + pid_number = kernel_thread(TimerQThread, pAd, CLONE_VM); + if (pid_number < 0) #endif #ifdef RT30xx pObj->TimerQThr_pid = NULL; @@ -826,7 +825,7 @@ NDIS_STATUS CreateThreads( return NDIS_STATUS_FAILURE; } #ifndef RT30xx - pObj->TimerQThr_task = tsk; + pObj->TimerQThr_pid = GET_PID(pid_number); #endif #ifdef RT30xx pObj->TimerQThr_pid = find_get_pid(pid_number); diff --git a/drivers/staging/rt2870/common/rtusb_io.c b/drivers/staging/rt2870/common/rtusb_io.c index fd1b0c18f2a0..704b5c2d5091 100644 --- a/drivers/staging/rt2870/common/rtusb_io.c +++ b/drivers/staging/rt2870/common/rtusb_io.c @@ -984,8 +984,7 @@ NDIS_STATUS RTUSBEnqueueCmdFromNdis( POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; #ifndef RT30xx - BUG_ON(pObj->RTUSBCmdThr_task == NULL); - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) #endif #ifdef RT30xx if (pObj->RTUSBCmdThr_pid < 0) diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h index 10e1640d61e5..2b8872b2fd9d 100644 --- a/drivers/staging/rt2870/rt2870.h +++ b/drivers/staging/rt2870/rt2870.h @@ -590,16 +590,14 @@ VOID RTUSBBulkRxComplete(purbb_t pUrb, struct pt_regs *pt_regs); #define RTUSBMlmeUp(pAd) \ { \ POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; \ - BUG_ON(pObj->MLMEThr_task == NULL); \ - CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task)) \ + CHECK_PID_LEGALITY(pObj->MLMEThr_pid) \ up(&(pAd->mlme_semaphore)); \ } #define RTUSBCMDUp(pAd) \ { \ POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie; \ - BUG_ON(pObj->RTUSBCmdThr_task == NULL); \ - CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task)) \ + CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid) \ up(&(pAd->RTUSBCmd_semaphore)); \ } #endif -- cgit v1.2.3 From ce9c010c5c39df05ed81a06aba492c45ee0c6f19 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Tue, 4 Aug 2009 16:53:36 -0700 Subject: Staging: rtl8192su: fix build error This fixes a build error when selecting the rtl8192su driver as a module. This has been reported by me, and the opensuse kernel developer team, and I finally tracked it down. Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rtl8192su/ieee80211.h | 2 +- drivers/staging/rtl8192su/ieee80211/ieee80211.h | 2 +- drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c | 3 ++- drivers/staging/rtl8192su/r8192U_core.c | 2 +- 4 files changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/staging/rtl8192su/ieee80211.h b/drivers/staging/rtl8192su/ieee80211.h index 0edb09a536f9..ea9739318037 100644 --- a/drivers/staging/rtl8192su/ieee80211.h +++ b/drivers/staging/rtl8192su/ieee80211.h @@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment( struct sk_buff *frag, int hdr_len); -extern int ieee80211_xmit(struct sk_buff *skb, +extern int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev); extern void ieee80211_txb_free(struct ieee80211_txb *); diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211.h b/drivers/staging/rtl8192su/ieee80211/ieee80211.h index 720bfcbfadc1..5e3a2cbed2b1 100644 --- a/drivers/staging/rtl8192su/ieee80211/ieee80211.h +++ b/drivers/staging/rtl8192su/ieee80211/ieee80211.h @@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment( struct sk_buff *frag, int hdr_len); -extern int ieee80211_xmit(struct sk_buff *skb, +extern int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev); extern void ieee80211_txb_free(struct ieee80211_txb *); diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c index 7294572b990f..cba12b84be5c 100644 --- a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c +++ b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c @@ -618,7 +618,7 @@ void ieee80211_query_seqnum(struct ieee80211_device*ieee, struct sk_buff* skb, u } } -int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) +int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) { #if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,5,0)) struct ieee80211_device *ieee = netdev_priv(dev); @@ -943,5 +943,6 @@ int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev) return 1; } +EXPORT_SYMBOL(rtl8192_ieee80211_xmit); EXPORT_SYMBOL(ieee80211_txb_free); diff --git a/drivers/staging/rtl8192su/r8192U_core.c b/drivers/staging/rtl8192su/r8192U_core.c index 4ab250743e81..70f81a8f1291 100644 --- a/drivers/staging/rtl8192su/r8192U_core.c +++ b/drivers/staging/rtl8192su/r8192U_core.c @@ -12142,7 +12142,7 @@ static const struct net_device_ops rtl8192_netdev_ops = { .ndo_set_mac_address = r8192_set_mac_adr, .ndo_validate_addr = eth_validate_addr, .ndo_change_mtu = eth_change_mtu, - .ndo_start_xmit = ieee80211_xmit, + .ndo_start_xmit = rtl8192_ieee80211_xmit, }; #if LINUX_VERSION_CODE > KERNEL_VERSION(2,5,0) -- cgit v1.2.3 From 5fb4d2525b6dcffbb8bc26a7dfc7ed17ad323a06 Mon Sep 17 00:00:00 2001 From: Jeff Mahoney Date: Fri, 7 Aug 2009 16:12:03 -0700 Subject: staging: add dependencies on PCI for drivers that require it This patch adds PCI dependencies to staging drivers that require it. Signed-off-by: Jeff Mahoney Signed-off-by: Greg Kroah-Hartman --- drivers/staging/b3dfg/Kconfig | 1 + drivers/staging/heci/Kconfig | 1 + 2 files changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/staging/b3dfg/Kconfig b/drivers/staging/b3dfg/Kconfig index 524231047de5..9e6573cf97d3 100644 --- a/drivers/staging/b3dfg/Kconfig +++ b/drivers/staging/b3dfg/Kconfig @@ -1,5 +1,6 @@ config B3DFG tristate "Brontes 3d Frame Framegrabber" + depends on PCI default n ---help--- This driver provides support for the Brontes 3d Framegrabber diff --git a/drivers/staging/heci/Kconfig b/drivers/staging/heci/Kconfig index ae8d588d3a27..c7206f8bcd93 100644 --- a/drivers/staging/heci/Kconfig +++ b/drivers/staging/heci/Kconfig @@ -1,5 +1,6 @@ config HECI tristate "Intel Management Engine Interface (MEI) Support" + depends on PCI ---help--- The Intel Management Engine Interface (Intel MEI) driver allows applications to access the Active Management Technology -- cgit v1.2.3 From 749d00dbf154fc2f9ac59df669205039de0d5b45 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 7 Aug 2009 21:00:10 +0200 Subject: Staging: rspiusb: Fix buffer overflow usb_buffer_map_sg() may return -1. This will result in a read from pdx->PixelUrb[frameInfo][-1] Signed-off-by: Roel Kluin Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rspiusb/rspiusb.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/staging/rspiusb/rspiusb.c b/drivers/staging/rspiusb/rspiusb.c index 2f8155c1968b..04e2f92c0f62 100644 --- a/drivers/staging/rspiusb/rspiusb.c +++ b/drivers/staging/rspiusb/rspiusb.c @@ -716,6 +716,8 @@ static int MapUserBuffer(struct ioctl_struct *io, struct device_extension *pdx) pdx->PixelUrb[frameInfo][i]->transfer_flags = URB_NO_TRANSFER_DMA_MAP | URB_NO_INTERRUPT; } + if (i == 0) + return -EINVAL; /* only interrupt when last URB completes */ pdx->PixelUrb[frameInfo][--i]->transfer_flags &= ~URB_NO_INTERRUPT; pdx->pendedPixelUrbs[frameInfo] = -- cgit v1.2.3 From 38d5487db7f289be1d56ac7df704ee49ed3213b9 Mon Sep 17 00:00:00 2001 From: Keith Packard Date: Mon, 20 Jul 2009 14:49:17 -0700 Subject: drm: When adding probed modes, preserve duplicate mode types The code which takes probed modes and adds them to a connector eliminates duplicate modes by comparing them using drm_mode_equal. That function doesn't consider the type bits, which means that any modes which differ only in the type field will be lost. One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit. If the mode with that bit is lost, then higher level code will not know which mode to select, causing a random mode to be used instead. This patch simply merges the two mode type bits together; that seems reasonable to me, but perhaps only a subset of the bits should be used? None of these can be user defined as they all come from looking at just the hardware. Signed-off-by: Keith Packard Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_modes.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_modes.c b/drivers/gpu/drm/drm_modes.c index 54f492a488a9..7914097b09c6 100644 --- a/drivers/gpu/drm/drm_modes.c +++ b/drivers/gpu/drm/drm_modes.c @@ -566,6 +566,8 @@ void drm_mode_connector_list_update(struct drm_connector *connector) found_it = 1; /* if equal delete the probed mode */ mode->status = pmode->status; + /* Merge type bits together */ + mode->type |= pmode->type; list_del(&pmode->head); drm_mode_destroy(connector->dev, pmode); break; -- cgit v1.2.3 From 8d3457ec3198a569dd14dc9e3ae8b6163bcaa0b5 Mon Sep 17 00:00:00 2001 From: Paul Rolland Date: Sun, 9 Aug 2009 12:24:01 +1000 Subject: drm: silence pointless vblank warning. Some applications/hardware combinations are triggering the message "failed to acquire vblank counter" to be issued up to 20 times a second, which makes it both useless and dangerous, as this may hide other important messages. This changes makes it only appear when people are debugging. Signed-off-by: Paul Rolland Reviewed-by: Jesse Barnes Lost-twice-by: Dave Airlie Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_irq.c b/drivers/gpu/drm/drm_irq.c index b4a3dbcebe9b..f85aaf21e783 100644 --- a/drivers/gpu/drm/drm_irq.c +++ b/drivers/gpu/drm/drm_irq.c @@ -566,7 +566,7 @@ int drm_wait_vblank(struct drm_device *dev, void *data, ret = drm_vblank_get(dev, crtc); if (ret) { - DRM_ERROR("failed to acquire vblank counter, %d\n", ret); + DRM_DEBUG("failed to acquire vblank counter, %d\n", ret); return ret; } seq = drm_vblank_count(dev, crtc); -- cgit v1.2.3 From 6cb504c29b1338925c83e4430e42a51eaa43781e Mon Sep 17 00:00:00 2001 From: Frans Pop Date: Sun, 9 Aug 2009 12:25:29 +1000 Subject: drm/i915: silence vblank warnings these errors are pretty pointless Reviewed-by: Jesse Barnes Signed-off-by: Dave Airlie --- drivers/gpu/drm/i915/i915_irq.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 83aee80e77a6..7ebc84c2881e 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -190,7 +190,7 @@ u32 i915_get_vblank_counter(struct drm_device *dev, int pipe) low_frame = pipe ? PIPEBFRAMEPIXEL : PIPEAFRAMEPIXEL; if (!i915_pipe_enabled(dev, pipe)) { - DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe); + DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe); return 0; } @@ -219,7 +219,7 @@ u32 gm45_get_vblank_counter(struct drm_device *dev, int pipe) int reg = pipe ? PIPEB_FRMCOUNT_GM45 : PIPEA_FRMCOUNT_GM45; if (!i915_pipe_enabled(dev, pipe)) { - DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe); + DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe); return 0; } -- cgit v1.2.3 From c8c00a6915a2e3d10416e8bdd3138429beb96210 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Mon, 10 Aug 2009 12:50:52 +1000 Subject: Remove deadlock potential in md_open A recent commit: commit 449aad3e25358812c43afc60918c5ad3819488e7 introduced the possibility of an A-B/B-A deadlock between bd_mutex and reconfig_mutex. __blkdev_get holds bd_mutex while calling md_open which takes reconfig_mutex, do_md_run is always called with reconfig_mutex held, and it now takes bd_mutex in the call the revalidate_disk. This potential deadlock was not caught by lockdep due to the use of mutex_lock_interruptible_nexted which was introduced by commit d63a5a74dee87883fda6b7d170244acaac5b05e8 do avoid a warning of an impossible deadlock. It is quite possible to split reconfig_mutex in to two locks. One protects the array data structures while it is being reconfigured, the other ensures that an array is never even partially open while it is being deactivated. In particular, the second lock prevents an open from completing between the time when do_md_stop checks if there are any active opens, and the time when the array is either set read-only, or when ->pers is set to NULL. So we can be certain that no IO is in flight as the array is being destroyed. So create a new lock, open_mutex, just to ensure exclusion between 'open' and 'stop'. This avoids the deadlock and also avoids the lockdep warning mentioned in commit d63a5a74d Reported-by: "Mike Snitzer" Reported-by: "H. Peter Anvin" Signed-off-by: NeilBrown --- drivers/md/md.c | 18 ++++++++++-------- drivers/md/md.h | 10 ++++++++++ 2 files changed, 20 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index 5b98bea4ff9b..5614500092e3 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -359,6 +359,7 @@ static mddev_t * mddev_find(dev_t unit) else new->md_minor = MINOR(unit) >> MdpMinorShift; + mutex_init(&new->open_mutex); mutex_init(&new->reconfig_mutex); INIT_LIST_HEAD(&new->disks); INIT_LIST_HEAD(&new->all_mddevs); @@ -4304,12 +4305,11 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) struct gendisk *disk = mddev->gendisk; mdk_rdev_t *rdev; + mutex_lock(&mddev->open_mutex); if (atomic_read(&mddev->openers) > is_open) { printk("md: %s still in use.\n",mdname(mddev)); - return -EBUSY; - } - - if (mddev->pers) { + err = -EBUSY; + } else if (mddev->pers) { if (mddev->sync_thread) { set_bit(MD_RECOVERY_FROZEN, &mddev->recovery); @@ -4367,7 +4367,10 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) set_disk_ro(disk, 1); clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery); } - +out: + mutex_unlock(&mddev->open_mutex); + if (err) + return err; /* * Free resources if final stop */ @@ -4433,7 +4436,6 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) blk_integrity_unregister(disk); md_new_event(mddev); sysfs_notify_dirent(mddev->sysfs_state); -out: return err; } @@ -5518,12 +5520,12 @@ static int md_open(struct block_device *bdev, fmode_t mode) } BUG_ON(mddev != bdev->bd_disk->private_data); - if ((err = mutex_lock_interruptible_nested(&mddev->reconfig_mutex, 1))) + if ((err = mutex_lock_interruptible(&mddev->open_mutex))) goto out; err = 0; atomic_inc(&mddev->openers); - mddev_unlock(mddev); + mutex_unlock(&mddev->open_mutex); check_disk_change(bdev); out: diff --git a/drivers/md/md.h b/drivers/md/md.h index 78f03168baf9..f8fc188bc762 100644 --- a/drivers/md/md.h +++ b/drivers/md/md.h @@ -223,6 +223,16 @@ struct mddev_s * so we don't loop trying */ int in_sync; /* know to not need resync */ + /* 'open_mutex' avoids races between 'md_open' and 'do_md_stop', so + * that we are never stopping an array while it is open. + * 'reconfig_mutex' protects all other reconfiguration. + * These locks are separate due to conflicting interactions + * with bdev->bd_mutex. + * Lock ordering is: + * reconfig_mutex -> bd_mutex : e.g. do_md_run -> revalidate_disk + * bd_mutex -> open_mutex: e.g. __blkdev_get -> md_open + */ + struct mutex open_mutex; struct mutex reconfig_mutex; atomic_t active; /* general refcount */ atomic_t openers; /* number of active opens */ -- cgit v1.2.3 From 5d5ceb8bdde403529ad9849f300dc80b1884550f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 13:06:03 +0000 Subject: irda: fix read buffer overflow io[i] is read before the bounds check on i, order should be reversed. Signed-off-by: Roel Kluin Cc: Samuel Ortiz Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- drivers/net/irda/w83977af_ir.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/irda/w83977af_ir.c b/drivers/net/irda/w83977af_ir.c index d0883835b0c6..fe4f2b2bff96 100644 --- a/drivers/net/irda/w83977af_ir.c +++ b/drivers/net/irda/w83977af_ir.c @@ -115,7 +115,7 @@ static int __init w83977af_init(void) IRDA_DEBUG(0, "%s()\n", __func__ ); - for (i=0; (io[i] < 2000) && (i < ARRAY_SIZE(dev_self)); i++) { + for (i=0; i < ARRAY_SIZE(dev_self) && io[i] < 2000; i++) { if (w83977af_open(i, io[i], irq[i], dma[i]) == 0) return 0; } -- cgit v1.2.3 From 082ba88a5e6b1425abed3fae4ad65e0e985ed081 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 6 Aug 2009 13:06:56 +0000 Subject: atlx: strncpy does not null terminate string strlcpy() will always null terminate the string. Signed-off-by: Roel Kluin Cc: Jay Cliburn Cc: Chris Snook Cc: Jie Yang Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- drivers/net/atl1c/atl1c_ethtool.c | 8 ++++---- drivers/net/atlx/atl1.c | 8 ++++---- 2 files changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/atl1c/atl1c_ethtool.c b/drivers/net/atl1c/atl1c_ethtool.c index 607007d75b6f..00d11b480af3 100644 --- a/drivers/net/atl1c/atl1c_ethtool.c +++ b/drivers/net/atl1c/atl1c_ethtool.c @@ -232,11 +232,11 @@ static void atl1c_get_drvinfo(struct net_device *netdev, { struct atl1c_adapter *adapter = netdev_priv(netdev); - strncpy(drvinfo->driver, atl1c_driver_name, sizeof(drvinfo->driver)); - strncpy(drvinfo->version, atl1c_driver_version, + strlcpy(drvinfo->driver, atl1c_driver_name, sizeof(drvinfo->driver)); + strlcpy(drvinfo->version, atl1c_driver_version, sizeof(drvinfo->version)); - strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); - strncpy(drvinfo->bus_info, pci_name(adapter->pdev), + strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); + strlcpy(drvinfo->bus_info, pci_name(adapter->pdev), sizeof(drvinfo->bus_info)); drvinfo->n_stats = 0; drvinfo->testinfo_len = 0; diff --git a/drivers/net/atlx/atl1.c b/drivers/net/atlx/atl1.c index 94d7325caf4f..8bca12f71390 100644 --- a/drivers/net/atlx/atl1.c +++ b/drivers/net/atlx/atl1.c @@ -3378,11 +3378,11 @@ static void atl1_get_drvinfo(struct net_device *netdev, { struct atl1_adapter *adapter = netdev_priv(netdev); - strncpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver)); - strncpy(drvinfo->version, ATLX_DRIVER_VERSION, + strlcpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver)); + strlcpy(drvinfo->version, ATLX_DRIVER_VERSION, sizeof(drvinfo->version)); - strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); - strncpy(drvinfo->bus_info, pci_name(adapter->pdev), + strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); + strlcpy(drvinfo->bus_info, pci_name(adapter->pdev), sizeof(drvinfo->bus_info)); drvinfo->eedump_len = ATL1_EEDUMP_LEN; } -- cgit v1.2.3 From 9555b31e8c29d2000e1e1f569f6f242ebd596e47 Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Thu, 6 Aug 2009 17:58:18 +0000 Subject: fec: fix FEC driver packet transmission breakage Commit f0b3fbeae11a526c3d308b691684589ee37c359b ("FEC Buffer rework") breaks transmission of packets where the skb data buffer is not memory aligned according to FEC_ALIGNMENT. It incorrectly passes to dma_sync_single() the buffer address directly from the skb, instead of the address calculated for use (which may be the skb address or one of the bounce buffers). It seems there is no use converting the cpu address of the buffer to a physical either, since dma_map_single() expects the cpu address and will return the dma address to use in the descriptor. So remove the use of __pa() on the buffer address as well. This patch is against 2.6.30-rc5. This breakage is a regression over 2.6.30, which does not have this problem. Signed-off-by: Greg Ungerer Signed-off-by: David S. Miller --- drivers/net/fec.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/fec.c b/drivers/net/fec.c index d4b98074b1b7..c9fd82d3a80d 100644 --- a/drivers/net/fec.c +++ b/drivers/net/fec.c @@ -285,6 +285,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct fec_enet_private *fep = netdev_priv(dev); struct bufdesc *bdp; + void *bufaddr; unsigned short status; unsigned long flags; @@ -312,7 +313,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) status &= ~BD_ENET_TX_STATS; /* Set buffer length and buffer pointer */ - bdp->cbd_bufaddr = __pa(skb->data); + bufaddr = skb->data; bdp->cbd_datlen = skb->len; /* @@ -320,11 +321,11 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) * 4-byte boundaries. Use bounce buffers to copy data * and get it aligned. Ugh. */ - if (bdp->cbd_bufaddr & FEC_ALIGNMENT) { + if (((unsigned long) bufaddr) & FEC_ALIGNMENT) { unsigned int index; index = bdp - fep->tx_bd_base; memcpy(fep->tx_bounce[index], (void *)skb->data, skb->len); - bdp->cbd_bufaddr = __pa(fep->tx_bounce[index]); + bufaddr = fep->tx_bounce[index]; } /* Save skb pointer */ @@ -336,7 +337,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) /* Push the data cache so the CPM does not get stale memory * data. */ - bdp->cbd_bufaddr = dma_map_single(&dev->dev, skb->data, + bdp->cbd_bufaddr = dma_map_single(&dev->dev, bufaddr, FEC_ENET_TX_FRSIZE, DMA_TO_DEVICE); /* Send it on its way. Tell FEC it's ready, interrupt when done, -- cgit v1.2.3 From 876bfd4d0f18cd1f698249870c7e7fb944de1c26 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Thu, 6 Aug 2009 14:22:44 +0000 Subject: tun: Extend RTNL lock coverage over whole ioctl As it is, parts of the ioctl runs under the RTNL and parts of it do not. The unlocked section is still protected by the BKL, but there can be subtle races. For example, Eric Biederman and Paul Moore observed that if two threads tried to create two tun devices on the same file descriptor, then unexpected results may occur. As there isn't anything in the ioctl that is expected to sleep indefinitely, we can prevent this from occurring by extending the RTNL lock coverage. This also allows to get rid of the BKL. Finally, I changed tun_get_iff to take a tun device in order to avoid calling tun_put which would dead-lock as it also tries to take the RTNL lock. Signed-off-by: Herbert Xu Signed-off-by: David S. Miller --- drivers/net/tun.c | 50 +++++++++++++++++++------------------------------- 1 file changed, 19 insertions(+), 31 deletions(-) (limited to 'drivers') diff --git a/drivers/net/tun.c b/drivers/net/tun.c index 027f7aba26af..42b6c6319bc2 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -1048,20 +1048,15 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr) return err; } -static int tun_get_iff(struct net *net, struct file *file, struct ifreq *ifr) +static int tun_get_iff(struct net *net, struct tun_struct *tun, + struct ifreq *ifr) { - struct tun_struct *tun = tun_get(file); - - if (!tun) - return -EBADFD; - DBG(KERN_INFO "%s: tun_get_iff\n", tun->dev->name); strcpy(ifr->ifr_name, tun->dev->name); ifr->ifr_flags = tun_flags(tun); - tun_put(tun); return 0; } @@ -1105,8 +1100,8 @@ static int set_offload(struct net_device *dev, unsigned long arg) return 0; } -static int tun_chr_ioctl(struct inode *inode, struct file *file, - unsigned int cmd, unsigned long arg) +static long tun_chr_ioctl(struct file *file, unsigned int cmd, + unsigned long arg) { struct tun_file *tfile = file->private_data; struct tun_struct *tun; @@ -1128,34 +1123,32 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, (unsigned int __user*)argp); } + rtnl_lock(); + tun = __tun_get(tfile); if (cmd == TUNSETIFF && !tun) { - int err; - ifr.ifr_name[IFNAMSIZ-1] = '\0'; - rtnl_lock(); - err = tun_set_iff(tfile->net, file, &ifr); - rtnl_unlock(); + ret = tun_set_iff(tfile->net, file, &ifr); - if (err) - return err; + if (ret) + goto unlock; if (copy_to_user(argp, &ifr, sizeof(ifr))) - return -EFAULT; - return 0; + ret = -EFAULT; + goto unlock; } - + ret = -EBADFD; if (!tun) - return -EBADFD; + goto unlock; DBG(KERN_INFO "%s: tun_chr_ioctl cmd %d\n", tun->dev->name, cmd); ret = 0; switch (cmd) { case TUNGETIFF: - ret = tun_get_iff(current->nsproxy->net_ns, file, &ifr); + ret = tun_get_iff(current->nsproxy->net_ns, tun, &ifr); if (ret) break; @@ -1201,7 +1194,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, case TUNSETLINK: /* Only allow setting the type when the interface is down */ - rtnl_lock(); if (tun->dev->flags & IFF_UP) { DBG(KERN_INFO "%s: Linktype set failed because interface is up\n", tun->dev->name); @@ -1211,7 +1203,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, DBG(KERN_INFO "%s: linktype set to %d\n", tun->dev->name, tun->dev->type); ret = 0; } - rtnl_unlock(); break; #ifdef TUN_DEBUG @@ -1220,9 +1211,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, break; #endif case TUNSETOFFLOAD: - rtnl_lock(); ret = set_offload(tun->dev, arg); - rtnl_unlock(); break; case TUNSETTXFILTER: @@ -1230,9 +1219,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, ret = -EINVAL; if ((tun->flags & TUN_TYPE_MASK) != TUN_TAP_DEV) break; - rtnl_lock(); ret = update_filter(&tun->txflt, (void __user *)arg); - rtnl_unlock(); break; case SIOCGIFHWADDR: @@ -1248,9 +1235,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, DBG(KERN_DEBUG "%s: set hw address: %pM\n", tun->dev->name, ifr.ifr_hwaddr.sa_data); - rtnl_lock(); ret = dev_set_mac_address(tun->dev, &ifr.ifr_hwaddr); - rtnl_unlock(); break; case TUNGETSNDBUF: @@ -1273,7 +1258,10 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file, break; }; - tun_put(tun); +unlock: + rtnl_unlock(); + if (tun) + tun_put(tun); return ret; } @@ -1361,7 +1349,7 @@ static const struct file_operations tun_fops = { .write = do_sync_write, .aio_write = tun_chr_aio_write, .poll = tun_chr_poll, - .ioctl = tun_chr_ioctl, + .unlocked_ioctl = tun_chr_ioctl, .open = tun_chr_open, .release = tun_chr_close, .fasync = tun_chr_fasync -- cgit v1.2.3 From a6616b42fbc39c1ccc2373996f1441ce7707ea93 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 6 Aug 2009 13:05:23 +0000 Subject: ixgbe: Pass rx_ring directly in ixgbe_configure_srrctl() Instead of passing the register index of the corresponding rx_ring and find the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(), simplify the function ixgbe_configure_srrctl() by passing the rx_ring into it. Then the register index for that rx_ring is already available from rx_ring->reg_idx. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 55 ++++++++++++------------------------------ 1 file changed, 15 insertions(+), 40 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 110c65ab5cb5..e361b7f01019 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -1898,46 +1898,19 @@ static void ixgbe_configure_tx(struct ixgbe_adapter *adapter) #define IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT 2 -static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, int index) +static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, + struct ixgbe_ring *rx_ring) { - struct ixgbe_ring *rx_ring; u32 srrctl; - int queue0 = 0; - unsigned long mask; + int index; struct ixgbe_ring_feature *feature = adapter->ring_feature; - if (adapter->hw.mac.type == ixgbe_mac_82599EB) { - if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) { - int dcb_i = feature[RING_F_DCB].indices; - if (dcb_i == 8) - queue0 = index >> 4; - else if (dcb_i == 4) - queue0 = index >> 5; - else - dev_err(&adapter->pdev->dev, "Invalid DCB " - "configuration\n"); -#ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { - struct ixgbe_ring_feature *f; - - rx_ring = &adapter->rx_ring[queue0]; - f = &adapter->ring_feature[RING_F_FCOE]; - if ((queue0 == 0) && (index > rx_ring->reg_idx)) - queue0 = f->mask + index - - rx_ring->reg_idx - 1; - } -#endif /* IXGBE_FCOE */ - } else { - queue0 = index; - } - } else { + index = rx_ring->reg_idx; + if (adapter->hw.mac.type == ixgbe_mac_82598EB) { + unsigned long mask; mask = (unsigned long) feature[RING_F_RSS].mask; - queue0 = index & mask; index = index & mask; } - - rx_ring = &adapter->rx_ring[queue0]; - srrctl = IXGBE_READ_REG(&adapter->hw, IXGBE_SRRCTL(index)); srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK; @@ -2002,6 +1975,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) { u64 rdba; struct ixgbe_hw *hw = &adapter->hw; + struct ixgbe_ring *rx_ring; struct net_device *netdev = adapter->netdev; int max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN; int i, j; @@ -2070,16 +2044,17 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) * the Base and Length of the Rx Descriptor Ring */ for (i = 0; i < adapter->num_rx_queues; i++) { - rdba = adapter->rx_ring[i].dma; - j = adapter->rx_ring[i].reg_idx; + rx_ring = &adapter->rx_ring[i]; + rdba = rx_ring->dma; + j = rx_ring->reg_idx; IXGBE_WRITE_REG(hw, IXGBE_RDBAL(j), (rdba & DMA_BIT_MASK(32))); IXGBE_WRITE_REG(hw, IXGBE_RDBAH(j), (rdba >> 32)); IXGBE_WRITE_REG(hw, IXGBE_RDLEN(j), rdlen); IXGBE_WRITE_REG(hw, IXGBE_RDH(j), 0); IXGBE_WRITE_REG(hw, IXGBE_RDT(j), 0); - adapter->rx_ring[i].head = IXGBE_RDH(j); - adapter->rx_ring[i].tail = IXGBE_RDT(j); - adapter->rx_ring[i].rx_buf_len = rx_buf_len; + rx_ring->head = IXGBE_RDH(j); + rx_ring->tail = IXGBE_RDT(j); + rx_ring->rx_buf_len = rx_buf_len; #ifdef IXGBE_FCOE if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { @@ -2087,12 +2062,12 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) f = &adapter->ring_feature[RING_F_FCOE]; if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) && (i >= f->mask) && (i < f->mask + f->indices)) - adapter->rx_ring[i].rx_buf_len = + rx_ring->rx_buf_len = IXGBE_FCOE_JUMBO_FRAME_SIZE; } #endif /* IXGBE_FCOE */ - ixgbe_configure_srrctl(adapter, j); + ixgbe_configure_srrctl(adapter, rx_ring); } if (hw->mac.type == ixgbe_mac_82598EB) { -- cgit v1.2.3 From 6e455b897bb6be3a4c0c6578f679e83d399e5b92 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 6 Aug 2009 13:05:44 +0000 Subject: ixgbe: Disable packet split only on FCoE queues in 82599 For 82599, packet split has to be disabled for FCoE direct data placement. However, this is only required on received queues allocated for FCoE. This patch adds a per ring flags to indicate if packet split is disabled on a per queue basis, particularly for FCoE, as packet split must be disabled for large receive using direct data placement (DDP). Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe.h | 2 ++ drivers/net/ixgbe/ixgbe_main.c | 33 +++++++++++++++++---------------- 2 files changed, 19 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index e11d83d5852b..2c4dc8221dcd 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -136,6 +136,8 @@ struct ixgbe_ring { u8 queue_index; /* needed for multiqueue queue management */ +#define IXGBE_RING_RX_PS_ENABLED (u8)(1) + u8 flags; /* per ring feature flags */ u16 head; u16 tail; diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e361b7f01019..e3cb949b9aa9 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -585,7 +585,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter, rx_desc = IXGBE_RX_DESC_ADV(*rx_ring, i); if (!bi->page_dma && - (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED)) { + (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED)) { if (!bi->page) { bi->page = alloc_page(GFP_ATOMIC); if (!bi->page) { @@ -629,7 +629,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter, } /* Refresh the desc even if buffer_addrs didn't change because * each write-back erases this info. */ - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { rx_desc->read.pkt_addr = cpu_to_le64(bi->page_dma); rx_desc->read.hdr_addr = cpu_to_le64(bi->dma); } else { @@ -726,7 +726,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, break; (*work_done)++; - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { hdr_info = le16_to_cpu(ixgbe_get_hdr_info(rx_desc)); len = (hdr_info & IXGBE_RXDADV_HDRBUFLEN_MASK) >> IXGBE_RXDADV_HDRBUFLEN_SHIFT; @@ -798,7 +798,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector, rx_ring->stats.packets++; rx_ring->stats.bytes += skb->len; } else { - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { rx_buffer_info->skb = next_buffer->skb; rx_buffer_info->dma = next_buffer->dma; next_buffer->skb = skb; @@ -1919,7 +1919,7 @@ static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, srrctl |= (IXGBE_RX_HDR_SIZE << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) & IXGBE_SRRCTL_BSIZEHDR_MASK; - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { #if (PAGE_SIZE / 2) > IXGBE_MAX_RXBUFFER srrctl |= IXGBE_MAX_RXBUFFER >> IXGBE_SRRCTL_BSIZEPKT_SHIFT; #else @@ -1992,11 +1992,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) /* Decide whether to use packet split mode or not */ adapter->flags |= IXGBE_FLAG_RX_PS_ENABLED; -#ifdef IXGBE_FCOE - if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) - adapter->flags &= ~IXGBE_FLAG_RX_PS_ENABLED; -#endif /* IXGBE_FCOE */ - /* Set the RX buffer length according to the mode */ if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { rx_buf_len = IXGBE_RX_HDR_SIZE; @@ -2056,14 +2051,19 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) rx_ring->tail = IXGBE_RDT(j); rx_ring->rx_buf_len = rx_buf_len; + if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) + rx_ring->flags |= IXGBE_RING_RX_PS_ENABLED; + #ifdef IXGBE_FCOE if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) { struct ixgbe_ring_feature *f; f = &adapter->ring_feature[RING_F_FCOE]; - if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) && - (i >= f->mask) && (i < f->mask + f->indices)) - rx_ring->rx_buf_len = - IXGBE_FCOE_JUMBO_FRAME_SIZE; + if ((i >= f->mask) && (i < f->mask + f->indices)) { + rx_ring->flags &= ~IXGBE_RING_RX_PS_ENABLED; + if (rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) + rx_ring->rx_buf_len = + IXGBE_FCOE_JUMBO_FRAME_SIZE; + } } #endif /* IXGBE_FCOE */ @@ -2143,7 +2143,8 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) { /* Enable 82599 HW-RSC */ for (i = 0; i < adapter->num_rx_queues; i++) { - j = adapter->rx_ring[i].reg_idx; + rx_ring = &adapter->rx_ring[i]; + j = rx_ring->reg_idx; rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j)); rscctrl |= IXGBE_RSCCTL_RSCEN; /* @@ -2151,7 +2152,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) * total size of max desc * buf_len is not greater * than 65535 */ - if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) { + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { #if (MAX_SKB_FRAGS > 16) rscctrl |= IXGBE_RSCCTL_MAXDESC_16; #elif (MAX_SKB_FRAGS > 8) -- cgit v1.2.3 From 373a88d78be540c1331ea5adcb76610dddcb008b Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 7 Aug 2009 07:41:37 +0000 Subject: e1000e: fix acquisition of SW/FW/HW semaphore for ICHx parts For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to acquire the SW/FW/HW semaphore instead of multiple times to prevent the hardware from having problems (especially for systems with manageability enabled), and extend the timeout for the hardware to set the SWFLAG bit. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/ich8lan.c | 44 +++++++++++++++++++++++++++++++------------- 1 file changed, 31 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index d56c7473144a..dd61e7e98ddb 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -594,8 +594,8 @@ static DEFINE_MUTEX(nvm_mutex); **/ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) { - u32 extcnf_ctrl; - u32 timeout = PHY_CFG_TIMEOUT; + u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT; + s32 ret_val = 0; might_sleep(); @@ -603,28 +603,46 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw) while (timeout) { extcnf_ctrl = er32(EXTCNF_CTRL); + if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) + break; - if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) { - extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); + mdelay(1); + timeout--; + } + + if (!timeout) { + hw_dbg(hw, "SW/FW/HW has locked the resource for too long.\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + timeout = PHY_CFG_TIMEOUT * 2; + + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + ew32(EXTCNF_CTRL, extcnf_ctrl); + + while (timeout) { + extcnf_ctrl = er32(EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; - extcnf_ctrl = er32(EXTCNF_CTRL); - if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) - break; - } mdelay(1); timeout--; } if (!timeout) { - hw_dbg(hw, "FW or HW has locked the resource for too long.\n"); + hw_dbg(hw, "Failed to acquire the semaphore.\n"); extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; ew32(EXTCNF_CTRL, extcnf_ctrl); - mutex_unlock(&nvm_mutex); - return -E1000_ERR_CONFIG; + ret_val = -E1000_ERR_CONFIG; + goto out; } - return 0; +out: + if (ret_val) + mutex_unlock(&nvm_mutex); + + return ret_val; } /** -- cgit v1.2.3 From 148675a7b2061b5a5eb194530b7c4d8de1f2887e Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 7 Aug 2009 07:41:56 +0000 Subject: e1000e: fix potential NVM corruption on ICH9 with 8K bank size The bank offset was being incorrectly calculated on ICH9 parts with a bank size of 8K (instead of the more common 4K bank) which would cause any NVM writes to be done on the wrong address after switching from bank 1 to bank 0. Additionally, assume we are meant to use bank 0 if a valid bank is not detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore when writing to the shadow ram version of the NVM image. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/ich8lan.c | 50 +++++++++++--------------------------------- 1 file changed, 12 insertions(+), 38 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index dd61e7e98ddb..99df2abf82a9 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -338,10 +338,7 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) { struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - union ich8_hws_flash_status hsfsts; - u32 gfpreg; - u32 sector_base_addr; - u32 sector_end_addr; + u32 gfpreg, sector_base_addr, sector_end_addr; u16 i; /* Can't read flash registers if the register set isn't mapped. */ @@ -375,20 +372,6 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw) /* Adjust to word count */ nvm->flash_bank_size /= sizeof(u16); - /* - * Make sure the flash bank size does not overwrite the 4k - * sector ranges. We may have 64k allotted to us but we only care - * about the first 2 4k sectors. Therefore, if we have anything less - * than 64k set in the HSFSTS register, we will reduce the bank size - * down to 4k and let the rest remain unused. If berasesz == 3, then - * we are working in 64k mode. Otherwise we are not. - */ - if (nvm->flash_bank_size > E1000_ICH8_SHADOW_RAM_WORDS) { - hsfsts.regval = er16flash(ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.berasesz != 3) - nvm->flash_bank_size = E1000_ICH8_SHADOW_RAM_WORDS; - } - nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS; /* Clear shadow ram */ @@ -1324,7 +1307,7 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; u32 act_offset; - s32 ret_val; + s32 ret_val = 0; u32 bank = 0; u16 i, word; @@ -1339,12 +1322,15 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, goto out; ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); - if (ret_val) - goto release; + if (ret_val) { + hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } act_offset = (bank) ? nvm->flash_bank_size : 0; act_offset += offset; + ret_val = 0; for (i = 0; i < words; i++) { if ((dev_spec->shadow_ram) && (dev_spec->shadow_ram[offset+i].modified)) { @@ -1359,7 +1345,6 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, } } -release: e1000_release_swflag_ich8lan(hw); out: @@ -1610,7 +1595,6 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, { struct e1000_nvm_info *nvm = &hw->nvm; struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - s32 ret_val; u16 i; if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || @@ -1619,17 +1603,11 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, return -E1000_ERR_NVM; } - ret_val = e1000_acquire_swflag_ich8lan(hw); - if (ret_val) - return ret_val; - for (i = 0; i < words; i++) { dev_spec->shadow_ram[offset+i].modified = 1; dev_spec->shadow_ram[offset+i].value = data[i]; } - e1000_release_swflag_ich8lan(hw); - return 0; } @@ -1670,8 +1648,8 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw) */ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); if (ret_val) { - e1000_release_swflag_ich8lan(hw); - goto out; + hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n"); + bank = 0; } if (bank == 0) { @@ -2057,12 +2035,8 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) iteration = 1; break; case 2: - if (hw->mac.type == e1000_ich9lan) { - sector_size = ICH_FLASH_SEG_SIZE_8K; - iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K; - } else { - return -E1000_ERR_NVM; - } + sector_size = ICH_FLASH_SEG_SIZE_8K; + iteration = 1; break; case 3: sector_size = ICH_FLASH_SEG_SIZE_64K; @@ -2074,7 +2048,7 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank) /* Start with the base address, then add the sector offset. */ flash_linear_addr = hw->nvm.flash_base_addr; - flash_linear_addr += (bank) ? (sector_size * iteration) : 0; + flash_linear_addr += (bank) ? flash_bank_size : 0; for (j = 0; j < iteration ; j++) { do { -- cgit v1.2.3 From 75c4885924f01aed1f887886a49dfa89960de240 Mon Sep 17 00:00:00 2001 From: Yong Zhang Date: Fri, 7 Aug 2009 16:36:52 +0000 Subject: gianfar: keep vlan related state when restart If vlan has been enabled. ifdown followed by ifup will lost hardware related state. Also remove duplicated operation in gfar_vlan_rx_register(). Signed-off-by: Yong Zhang Acked-by: Dai Haruki Signed-off-by: David S. Miller --- drivers/net/gianfar.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index f8ffcbf0bc39..e212f2c5448b 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -936,6 +936,7 @@ int startup_gfar(struct net_device *dev) struct gfar __iomem *regs = priv->regs; int err = 0; u32 rctrl = 0; + u32 tctrl = 0; u32 attrs = 0; gfar_write(®s->imask, IMASK_INIT_CLEAR); @@ -1111,11 +1112,19 @@ int startup_gfar(struct net_device *dev) rctrl |= RCTRL_PADDING(priv->padding); } + /* keep vlan related bits if it's enabled */ + if (priv->vlgrp) { + rctrl |= RCTRL_VLEX | RCTRL_PRSDEP_INIT; + tctrl |= TCTRL_VLINS; + } + /* Init rctrl based on our settings */ gfar_write(&priv->regs->rctrl, rctrl); if (dev->features & NETIF_F_IP_CSUM) - gfar_write(&priv->regs->tctrl, TCTRL_INIT_CSUM); + tctrl |= TCTRL_INIT_CSUM; + + gfar_write(&priv->regs->tctrl, tctrl); /* Set the extraction length and index */ attrs = ATTRELI_EL(priv->rx_stash_size) | @@ -1450,7 +1459,6 @@ static void gfar_vlan_rx_register(struct net_device *dev, /* Enable VLAN tag extraction */ tempval = gfar_read(&priv->regs->rctrl); - tempval |= RCTRL_VLEX; tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT); gfar_write(&priv->regs->rctrl, tempval); } else { -- cgit v1.2.3 From 5e33b719c8fcccfedc1d25167826a0f93fe6c5a1 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 7 Aug 2009 03:24:27 +0000 Subject: pcnet32: Read buffer overflow An `options[cards_found]' that equals `sizeof(options_mapping)' is already beyond the array. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/pcnet32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c index a646a445fda9..23e1a0750fe0 100644 --- a/drivers/net/pcnet32.c +++ b/drivers/net/pcnet32.c @@ -1839,7 +1839,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) lp->chip_version = chip_version; lp->msg_enable = pcnet32_debug; if ((cards_found >= MAX_UNITS) - || (options[cards_found] > sizeof(options_mapping))) + || (options[cards_found] >= sizeof(options_mapping))) lp->options = PCNET32_PORT_ASEL; else lp->options = options_mapping[options[cards_found]]; -- cgit v1.2.3 From be12159b24c532b4b48bdec5a543336438faa132 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sun, 9 Aug 2009 04:00:25 +0000 Subject: zorro8390: Fix read buffer overflow in zorro8390_init_one() Prevent read from cards[-1] when no card was found. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/zorro8390.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/net/zorro8390.c b/drivers/net/zorro8390.c index 37c84e3b8be0..81c753a617ab 100644 --- a/drivers/net/zorro8390.c +++ b/drivers/net/zorro8390.c @@ -120,6 +120,9 @@ static int __devinit zorro8390_init_one(struct zorro_dev *z, for (i = ARRAY_SIZE(cards)-1; i >= 0; i--) if (z->id == cards[i].id) break; + if (i < 0) + return -ENODEV; + board = z->resource.start; ioaddr = board+cards[i].offset; dev = alloc_ei_netdev(); -- cgit v1.2.3 From 973507cb8610d4c84f090d5f1f0ca54fa0559d27 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Sat, 8 Aug 2009 23:54:21 +0000 Subject: mlx4_en: Fix read buffer overflow in mlx4_en_complete_rx_desc() If the length is less or equal to frag_prefix_size in the first iteration we write skb_frags_rx[-1] and read from priv->frag_info[-1] Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/mlx4/en_rx.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/mlx4/en_rx.c b/drivers/net/mlx4/en_rx.c index 91bdfdfd431f..3ac0404d0d11 100644 --- a/drivers/net/mlx4/en_rx.c +++ b/drivers/net/mlx4/en_rx.c @@ -506,8 +506,9 @@ static int mlx4_en_complete_rx_desc(struct mlx4_en_priv *priv, PCI_DMA_FROMDEVICE); } /* Adjust size of last fragment to match actual length */ - skb_frags_rx[nr - 1].size = length - - priv->frag_info[nr - 1].frag_prefix_size; + if (nr > 0) + skb_frags_rx[nr - 1].size = length - + priv->frag_info[nr - 1].frag_prefix_size; return nr; fail: -- cgit v1.2.3 From 85dfd81dc57e8183a277ddd7a56aa65c96f3f487 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 10 Aug 2009 13:21:19 -0700 Subject: pty: fix data loss when stopped (^S/^Q) Commit d945cb9cc ("pty: Rework the pty layer to use the normal buffering logic") dropped the test for 'tty->stopped' in pty_write_room(), which then causes the n_tty line discipline thing to not throttle the data properly when the tty is stopped. So instead of pausing the write due to the tty being stopped, the ldisc layer would go ahead and push it down to the pty. The pty write() routine would then refuse to take the data (because it _did_ check 'stopped'), and the data wouldn't actually be written. This whole stopped test should eventually be moved into the tty ldisc layer rather than have low-level tty drivers care about these things, but right now the fix is to just re-instate the missing pty 'stopped' handling. Reported-and-tested-by: Artur Skawina Cc: Alan Cox Signed-off-by: Linus Torvalds --- drivers/char/pty.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/char/pty.c b/drivers/char/pty.c index 6e6942c45f5b..d083c73d784a 100644 --- a/drivers/char/pty.c +++ b/drivers/char/pty.c @@ -144,6 +144,8 @@ static int pty_write(struct tty_struct *tty, const unsigned char *buf, static int pty_write_room(struct tty_struct *tty) { + if (tty->stopped) + return 0; return pty_space(tty->link); } -- cgit v1.2.3 From 363ec5614f86110c6a6bdd72ac2147ebafd3ff5e Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Sat, 8 Aug 2009 17:09:48 +0200 Subject: ar9170usb: fix spurious firmware related message When ar9170-2.fw was missing, the driver erroneously complained about missing the initialization values file ar9170-1.fw... Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ar9170/usb.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/ar9170/usb.c b/drivers/net/wireless/ath/ar9170/usb.c index 754b1f8d8da9..007eb85fc67e 100644 --- a/drivers/net/wireless/ath/ar9170/usb.c +++ b/drivers/net/wireless/ath/ar9170/usb.c @@ -598,11 +598,15 @@ static int ar9170_usb_request_firmware(struct ar9170_usb *aru) err = request_firmware(&aru->init_values, "ar9170-1.fw", &aru->udev->dev); + if (err) { + dev_err(&aru->udev->dev, "file with init values not found.\n"); + return err; + } err = request_firmware(&aru->firmware, "ar9170-2.fw", &aru->udev->dev); if (err) { release_firmware(aru->init_values); - dev_err(&aru->udev->dev, "file with init values not found.\n"); + dev_err(&aru->udev->dev, "firmware file not found.\n"); return err; } -- cgit v1.2.3 From e9d126cdfa60b575f1b5b02024c4faee27dccf07 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sun, 9 Aug 2009 14:24:09 +0200 Subject: ar9170: fix read & write outside array bounds queue == __AR9170_NUM_TXQ would cause a bug on the next line. found by Smatch ( http://repo.or.cz/w/smatch.git ). Cc: stable@kernel.org Reported-by: Dan Carpenter Signed-off-by: Dan Carpenter Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ar9170/main.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/ath/ar9170/main.c b/drivers/net/wireless/ath/ar9170/main.c index 9d38cf60a0db..88c3d8573869 100644 --- a/drivers/net/wireless/ath/ar9170/main.c +++ b/drivers/net/wireless/ath/ar9170/main.c @@ -1967,13 +1967,14 @@ static int ar9170_conf_tx(struct ieee80211_hw *hw, u16 queue, int ret; mutex_lock(&ar->mutex); - if ((param) && !(queue > __AR9170_NUM_TXQ)) { + if (queue < __AR9170_NUM_TXQ) { memcpy(&ar->edcf[ar9170_qos_hwmap[queue]], param, sizeof(*param)); ret = ar9170_set_qos(ar); - } else + } else { ret = -EINVAL; + } mutex_unlock(&ar->mutex); return ret; -- cgit v1.2.3 From 651b1f125c7e3806bbd635739d009433dc07372d Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Mon, 10 Aug 2009 23:41:18 +0200 Subject: PM / Driver Core: Kill dev_pm_ops platform warning for now Commit 783ea7d4eeefe895f2731fe73ac951e94418927b (Driver Core: Rework platform suspend/resume, print warning) added a warning message printed for platform drivers that use the legacy PM callbacks rather than struct dev_pm_ops. Unfortunately, this resulted in some confusion and made some people try to convert drivers by replacing the old callbacks with struct dev_pm_ops in automatic way, which generally is not a good idea. Remove the platform device runtime dev_pm_ops warning for now, because it's annoying to users and it's not really necessary right now. [rjw: Modified the changelog to be more informative.] Signed-off-by: Magnus Damm Acked-by: Greg Kroah-Hartman Signed-off-by: Rafael J. Wysocki --- drivers/base/platform.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'drivers') diff --git a/drivers/base/platform.c b/drivers/base/platform.c index 81cb01bfc356..456594bd97bc 100644 --- a/drivers/base/platform.c +++ b/drivers/base/platform.c @@ -483,9 +483,6 @@ int platform_driver_register(struct platform_driver *drv) drv->driver.remove = platform_drv_remove; if (drv->shutdown) drv->driver.shutdown = platform_drv_shutdown; - if (drv->suspend || drv->resume) - pr_warning("Platform driver '%s' needs updating - please use " - "dev_pm_ops\n", drv->driver.name); return driver_register(&drv->driver); } -- cgit v1.2.3 From df9eba8c9febf53782ef896518e7177999d98188 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 7 Aug 2009 11:15:20 +0900 Subject: pata_at91: fix resource release Julias Lawall discovered that pata_at91 wasn't freeing a memory region allocated with kzalloc() on init failure paths. Upon review, pata_at91 also seems to be doing unnecessary explicit resource releases for managed resources too. Convert memory allocation to managed one and drop unnecessary explicit resource releases. Signed-off-by: Tejun Heo Cc: Julia Lawall Cc: Sergey Matyukevich Signed-off-by: Jeff Garzik --- drivers/ata/pata_at91.c | 17 ++++------------- 1 file changed, 4 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c index 5702affcb325..41c94b1ae493 100644 --- a/drivers/ata/pata_at91.c +++ b/drivers/ata/pata_at91.c @@ -250,7 +250,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) ata_port_desc(ap, "no IRQ, using PIO polling"); } - info = kzalloc(sizeof(*info), GFP_KERNEL); + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); if (!info) { dev_err(dev, "failed to allocate memory for private data\n"); @@ -275,7 +275,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) if (!info->ide_addr) { dev_err(dev, "failed to map IO base\n"); ret = -ENOMEM; - goto err_ide_ioremap; + goto err_put; } info->alt_addr = devm_ioremap(dev, @@ -284,7 +284,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) if (!info->alt_addr) { dev_err(dev, "failed to map CTL base\n"); ret = -ENOMEM; - goto err_alt_ioremap; + goto err_put; } ap->ioaddr.cmd_addr = info->ide_addr; @@ -303,13 +303,8 @@ static int __devinit pata_at91_probe(struct platform_device *pdev) irq ? ata_sff_interrupt : NULL, irq_flags, &pata_at91_sht); -err_alt_ioremap: - devm_iounmap(dev, info->ide_addr); - -err_ide_ioremap: +err_put: clk_put(info->mck); - kfree(info); - return ret; } @@ -317,7 +312,6 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) { struct ata_host *host = dev_get_drvdata(&pdev->dev); struct at91_ide_info *info; - struct device *dev = &pdev->dev; if (!host) return 0; @@ -328,11 +322,8 @@ static int __devexit pata_at91_remove(struct platform_device *pdev) if (!info) return 0; - devm_iounmap(dev, info->ide_addr); - devm_iounmap(dev, info->alt_addr); clk_put(info->mck); - kfree(info); return 0; } -- cgit v1.2.3 From 1fd4bbec8c0d6db96b02141f324066afa2e77e89 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 6 Aug 2009 17:47:05 +0200 Subject: pata_atiixp: fix second channel support PIO and MWDMA timings are never programmed for the second channel because timing registers are treated as 16-bit long ones. The bug is an attixp -> pata_atiixp regression and goes back to: commit 669a5db411d85a14f86cd92bc16bf7ab5b8aa235 Author: Jeff Garzik Date: Tue Aug 29 18:12:40 2006 -0400 [libata] Add a bunch of PATA drivers. Cc: Krystian Juskowiak Cc: Andrew Morton Cc: Borislav Petkov Cc: Robert Hancock Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jeff Garzik --- drivers/ata/pata_atiixp.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c index bec0b8ade66d..45915566e4e9 100644 --- a/drivers/ata/pata_atiixp.c +++ b/drivers/ata/pata_atiixp.c @@ -1,6 +1,7 @@ /* * pata_atiixp.c - ATI PATA for new ATA layer * (C) 2005 Red Hat Inc + * (C) 2009 Bartlomiej Zolnierkiewicz * * Based on * @@ -61,20 +62,19 @@ static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev, struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = 2 * ap->port_no + adev->devno; - - /* Check this is correct - the order is odd in both drivers */ int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); - u16 pio_mode_data, pio_timing_data; + u32 pio_timing_data; + u16 pio_mode_data; pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data); pio_mode_data &= ~(0x7 << (4 * dn)); pio_mode_data |= pio << (4 * dn); pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data); - pci_read_config_word(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); + pci_read_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); pio_timing_data &= ~(0xFF << timing_shift); pio_timing_data |= (pio_timings[pio] << timing_shift); - pci_write_config_word(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); + pci_write_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); } /** @@ -119,16 +119,17 @@ static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev) udma_mode_data |= dma << (4 * dn); pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data); } else { - u16 mwdma_timing_data; - /* Check this is correct - the order is odd in both drivers */ int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1); + u32 mwdma_timing_data; dma -= XFER_MW_DMA_0; - pci_read_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, &mwdma_timing_data); + pci_read_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, + &mwdma_timing_data); mwdma_timing_data &= ~(0xFF << timing_shift); mwdma_timing_data |= (mwdma_timings[dma] << timing_shift); - pci_write_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, mwdma_timing_data); + pci_write_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING, + mwdma_timing_data); } /* * We must now look at the PIO mode situation. We may need to -- cgit v1.2.3 From 7831387bda72af3059be48d39846d3eb6d8ce2f6 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 7 Aug 2009 01:59:15 +0900 Subject: libata: OCZ Vertex can't do HPA OCZ Vertex SSD can't do HPA and not in a usual way. It reports HPA, allows unlocking but then fails all IOs which fall in the unlocked area. Quirk it so that HPA unlocking is not used for the device. Reported by Daniel Perup in bnc#522414. https://bugzilla.novell.com/show_bug.cgi?id=522414 Signed-off-by: Tejun Heo Reported-by: Daniel Perup Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers') diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 8ac98ff16d7d..072ba5ea138f 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4302,6 +4302,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "WDC WD2500JD-00HBB0", "WD-WMAL71490727", ATA_HORKAGE_BROKEN_HPA }, { "MAXTOR 6L080L4", "A93.0500", ATA_HORKAGE_BROKEN_HPA }, + /* this one allows HPA unlocking but fails IOs on the area */ + { "OCZ-VERTEX", "1.30", ATA_HORKAGE_BROKEN_HPA }, + /* Devices which report 1 sector over size HPA */ { "ST340823A", NULL, ATA_HORKAGE_HPA_SIZE, }, { "ST320413A", NULL, ATA_HORKAGE_HPA_SIZE, }, -- cgit v1.2.3 From 51c8949950647afeeb897e08dd75ad99078adb50 Mon Sep 17 00:00:00 2001 From: Tony Vroon Date: Thu, 6 Aug 2009 00:50:09 +0100 Subject: sata_nv: MSI support, disabled by default At least the nVidia MCP55 controller quite happily supports MSI. This adds an option to use it. It is disabled by default. As per feedback by Robert Hancock, it will honour the user request as the kernel will not enable MSI where the controller or the specific system configuration do not support it. Signed-off-by: Tony Vroon Cc: Robert Hancock Signed-off-by: Jeff Garzik --- drivers/ata/sata_nv.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers') diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c index b2d11f300c39..86a40582999c 100644 --- a/drivers/ata/sata_nv.c +++ b/drivers/ata/sata_nv.c @@ -602,6 +602,7 @@ MODULE_VERSION(DRV_VERSION); static int adma_enabled; static int swncq_enabled = 1; +static int msi_enabled; static void nv_adma_register_mode(struct ata_port *ap) { @@ -2459,6 +2460,11 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } else if (type == SWNCQ) nv_swncq_host_init(host); + if (msi_enabled) { + dev_printk(KERN_NOTICE, &pdev->dev, "Using MSI\n"); + pci_enable_msi(pdev); + } + pci_set_master(pdev); return ata_host_activate(host, pdev->irq, ipriv->irq_handler, IRQF_SHARED, ipriv->sht); @@ -2558,4 +2564,6 @@ module_param_named(adma, adma_enabled, bool, 0444); MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)"); module_param_named(swncq, swncq_enabled, bool, 0444); MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)"); +module_param_named(msi, msi_enabled, bool, 0444); +MODULE_PARM_DESC(msi, "Enable use of MSI (Default: false)"); -- cgit v1.2.3 From b6931c1fbaf7fda9ea7f120228a96600d7090049 Mon Sep 17 00:00:00 2001 From: Shane Huang Date: Wed, 5 Aug 2009 10:10:41 +0800 Subject: ahci: Soften up the dmesg on SB600 PMP softreset failure recovery Too strong words led to spurious bug reports: Novell bugzilla #527748, RedHat bugzilla #468800. This patch is used to soften up the dmesg on SB600 PMP softreset failure recovery, so as to remove the scariness and concern from community. Reported-by: pgnet Dev Signed-off-by: Shane Huang Cc: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 958c1fa41900..838ff73b08e1 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -1773,7 +1773,8 @@ static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class, irq_sts = readl(port_mmio + PORT_IRQ_STAT); if (irq_sts & PORT_IRQ_BAD_PMP) { ata_link_printk(link, KERN_WARNING, - "failed due to HW bug, retry pmp=0\n"); + "applying SB600 PMP SRST workaround " + "and retrying\n"); rc = ahci_do_softreset(link, class, 0, deadline, ahci_check_ready); } -- cgit v1.2.3 From 5594639aab8b5614cb27a3e5b2b627505cbcd137 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Tue, 4 Aug 2009 14:30:08 +0900 Subject: ahci: add workaround for on-board 5723s on some gigabyte boards Some gigabytes have on-board SIMG5723s connected to JMB ahcis. These are used to implement hardware raid. Unfortunately some firmware revisions on these 5723s don't bring the link down when all the downstream ports are unoccupied while not responding to reset protocol which makes libata think that there's device attached to the port but is not responding and retry. This results in painfully wrong boot detection time for these ports when they're empty. This patch quirks those boards such that ahci gives up after the initial timeout. Combined with parallel probing, this gives quick enough probing and also is safe because SIMG5723 will respond to the first try if any of the downstream ports is occupied. Signed-off-by: Tejun Heo Reported-by: Marc Bowes Reported-by: Nicolas Mailhot Signed-off-by: Jeff Garzik --- drivers/ata/ahci.c | 76 +++++++++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 72 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 838ff73b08e1..fe3eba5d6b3e 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -219,6 +219,8 @@ enum { AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */ AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */ AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */ + AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as + link offline */ /* ap->flags bits */ @@ -1663,6 +1665,7 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class, int (*check_ready)(struct ata_link *link)) { struct ata_port *ap = link->ap; + struct ahci_host_priv *hpriv = ap->host->private_data; const char *reason = NULL; unsigned long now, msecs; struct ata_taskfile tf; @@ -1701,12 +1704,21 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class, /* wait for link to become ready */ rc = ata_wait_after_reset(link, deadline, check_ready); - /* link occupied, -ENODEV too is an error */ - if (rc) { + if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) { + /* + * Workaround for cases where link online status can't + * be trusted. Treat device readiness timeout as link + * offline. + */ + ata_link_printk(link, KERN_INFO, + "device not ready, treating as offline\n"); + *class = ATA_DEV_NONE; + } else if (rc) { + /* link occupied, -ENODEV too is an error */ reason = "device not ready"; goto fail; - } - *class = ahci_dev_classify(ap); + } else + *class = ahci_dev_classify(ap); DPRINTK("EXIT, class=%u\n", *class); return 0; @@ -2727,6 +2739,56 @@ static bool ahci_broken_suspend(struct pci_dev *pdev) return !ver || strcmp(ver, dmi->driver_data) < 0; } +static bool ahci_broken_online(struct pci_dev *pdev) +{ +#define ENCODE_BUSDEVFN(bus, slot, func) \ + (void *)(unsigned long)(((bus) << 8) | PCI_DEVFN((slot), (func))) + static const struct dmi_system_id sysids[] = { + /* + * There are several gigabyte boards which use + * SIMG5723s configured as hardware RAID. Certain + * 5723 firmware revisions shipped there keep the link + * online but fail to answer properly to SRST or + * IDENTIFY when no device is attached downstream + * causing libata to retry quite a few times leading + * to excessive detection delay. + * + * As these firmwares respond to the second reset try + * with invalid device signature, considering unknown + * sig as offline works around the problem acceptably. + */ + { + .ident = "EP45-DQ6", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, + "Gigabyte Technology Co., Ltd."), + DMI_MATCH(DMI_BOARD_NAME, "EP45-DQ6"), + }, + .driver_data = ENCODE_BUSDEVFN(0x0a, 0x00, 0), + }, + { + .ident = "EP45-DS5", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, + "Gigabyte Technology Co., Ltd."), + DMI_MATCH(DMI_BOARD_NAME, "EP45-DS5"), + }, + .driver_data = ENCODE_BUSDEVFN(0x03, 0x00, 0), + }, + { } /* terminate list */ + }; +#undef ENCODE_BUSDEVFN + const struct dmi_system_id *dmi = dmi_first_match(sysids); + unsigned int val; + + if (!dmi) + return false; + + val = (unsigned long)dmi->driver_data; + + return pdev->bus->number == (val >> 8) && pdev->devfn == (val & 0xff); +} + static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { static int printed_version; @@ -2842,6 +2904,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) "BIOS update required for suspend/resume\n"); } + if (ahci_broken_online(pdev)) { + hpriv->flags |= AHCI_HFLAG_SRST_TOUT_IS_OFFLINE; + dev_info(&pdev->dev, + "online status unreliable, applying workaround\n"); + } + /* CAP.NP sometimes indicate the index of the last enabled * port, at other times, that of the last possible port, so * determining the maximum port number requires looking at -- cgit v1.2.3 From 67fe0688082509c52bd451d10a61b3565169c23e Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Wed, 12 Aug 2009 06:29:57 -0400 Subject: Remove zero-length file drivers/mtd/maps/sbc8240.c It was "deleted" in commit 2bf961b7ccd69e108ac435c67e2b0522b403c578 Signed-off-by: Jeff Garzik --- drivers/mtd/maps/sbc8240.c | 0 1 file changed, 0 insertions(+), 0 deletions(-) delete mode 100644 drivers/mtd/maps/sbc8240.c (limited to 'drivers') diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c deleted file mode 100644 index e69de29bb2d1..000000000000 -- cgit v1.2.3 From 51d5668cb2e3fd1827a55184e48606fff054c5be Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 09:54:02 +1000 Subject: md: never advance 'events' counter by more than 1. When assembling arrays, md allows two devices to have different event counts as long as the difference is only '1'. This is to cope with a system failure between updating the metadata on two difference devices. However there are currently times when we update the event count by 2. This was done to keep the event count even when the array is clean and odd when it is dirty, which allows us to avoid writing common update to spare devices and so allow those spares to go to sleep. This is bad for the above reason. So change it to never increase by two. This means that the alignment between 'odd/even' and 'clean/dirty' might take a little longer to attain, but that is only a small cost. The spares will get a few more updates but that will still be spared (;-) most updates and can still go to sleep. Prior to this patch there was a small chance that after a crash an array would fail to assemble due to the overly large event count mismatch. Signed-off-by: NeilBrown --- drivers/md/md.c | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index 5614500092e3..d18805fea111 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -1975,17 +1975,14 @@ repeat: /* otherwise we have to go forward and ... */ mddev->events ++; if (!mddev->in_sync || mddev->recovery_cp != MaxSector) { /* not clean */ - /* .. if the array isn't clean, insist on an odd 'events' */ - if ((mddev->events&1)==0) { - mddev->events++; + /* .. if the array isn't clean, an 'even' event must also go + * to spares. */ + if ((mddev->events&1)==0) nospares = 0; - } } else { - /* otherwise insist on an even 'events' (for clean states) */ - if ((mddev->events&1)) { - mddev->events++; + /* otherwise an 'odd' event must go to spares */ + if ((mddev->events&1)) nospares = 0; - } } } -- cgit v1.2.3 From 67ac6011db5d2b0c853d573ff474b25c85dfb644 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:06:24 +1000 Subject: md/raid5: allow new reshape modes to be restarted in the middle. md/raid5 doesn't allow a reshape to restart if it involves writing over the same part of disk that it would be reading from. This happens at the beginning of a reshape that increases the number of devices, at the end of a reshape that decreases the number of devices, and continuously for a reshape that does not change the number of devices. The current code is correct for the "increase number of devices" case as the critical section at the start is handled by userspace performing a backup. It does not work for reducing the number of devices, or the no-change case. For 'reducing', we need to invert the test. For no-change we cannot really be sure things will be safe, so simply require the array to be read-only, which is how the user-space code which carefully starts such arrays works. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 2b521ee67dfa..b8a22a2205cf 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -4509,7 +4509,26 @@ static int run(mddev_t *mddev) (old_disks-max_degraded)); /* here_old is the first stripe that we might need to read * from */ - if (here_new >= here_old) { + if (mddev->delta_disks == 0) { + /* We cannot be sure it is safe to start an in-place + * reshape. It is only safe if user-space if monitoring + * and taking constant backups. + * mdadm always starts a situation like this in + * readonly mode so it can take control before + * allowing any writes. So just check for that. + */ + if ((here_new * mddev->new_chunk_sectors != + here_old * mddev->chunk_sectors) || + mddev->ro == 0) { + printk(KERN_ERR "raid5: in-place reshape must be started" + " in read-only mode - aborting\n"); + return -EINVAL; + } + } else if (mddev->delta_disks < 0 + ? (here_new * mddev->new_chunk_sectors <= + here_old * mddev->chunk_sectors) + : (here_new * mddev->new_chunk_sectors >= + here_old * mddev->chunk_sectors)) { /* Reading from the same stripe as writing to - bad */ printk(KERN_ERR "raid5: reshape_position too early for " "auto-recovery - aborting.\n"); -- cgit v1.2.3 From a639755cf885e437b2fe4168d35157fa90d530ab Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:13:00 +1000 Subject: md/raid5: make sure a reshape restarts at the correct address. This "if" don't allow for the possibility that the number of devices doesn't change, and so sector_nr isn't set correctly in that case. So change '>' to '>='. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index b8a22a2205cf..94a74cb5cccb 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -3785,7 +3785,7 @@ static sector_t reshape_request(mddev_t *mddev, sector_t sector_nr, int *skipped conf->reshape_progress < raid5_size(mddev, 0, 0)) { sector_nr = raid5_size(mddev, 0, 0) - conf->reshape_progress; - } else if (mddev->delta_disks > 0 && + } else if (mddev->delta_disks >= 0 && conf->reshape_progress > 0) sector_nr = conf->reshape_progress; sector_div(sector_nr, new_data_disks); -- cgit v1.2.3 From 9799218ae36910af50f002a5db1802d576fffb43 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 12 Aug 2009 17:37:52 -0700 Subject: Revert "libertas: Read buffer overflow" This reverts commit 57921c312e8cef72ba35a4cfe870b376da0b1b87. On request from John Linville: It has been shown to create a new problem. There is work towards a solution to that one, but it isn't a simple clean-up. Signed-off-by: David S. Miller --- drivers/net/wireless/libertas/assoc.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c index d6997371c27e..b9b374119033 100644 --- a/drivers/net/wireless/libertas/assoc.c +++ b/drivers/net/wireless/libertas/assoc.c @@ -1,7 +1,6 @@ /* Copyright (C) 2006, Red Hat, Inc. */ #include -#include #include #include #include @@ -44,21 +43,21 @@ static int get_common_rates(struct lbs_private *priv, u16 *rates_size) { u8 *card_rates = lbs_bg_rates; + size_t num_card_rates = sizeof(lbs_bg_rates); int ret = 0, i, j; - u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)]; + u8 tmp[30]; size_t tmp_size = 0; /* For each rate in card_rates that exists in rate1, copy to tmp */ - for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) { - for (j = 0; j < *rates_size && rates[j]; j++) { + for (i = 0; card_rates[i] && (i < num_card_rates); i++) { + for (j = 0; rates[j] && (j < *rates_size); j++) { if (rates[j] == card_rates[i]) tmp[tmp_size++] = card_rates[i]; } } lbs_deb_hex(LBS_DEB_JOIN, "AP rates ", rates, *rates_size); - lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, - ARRAY_SIZE(lbs_bg_rates)); + lbs_deb_hex(LBS_DEB_JOIN, "card rates ", card_rates, num_card_rates); lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size); lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate); @@ -70,7 +69,10 @@ static int get_common_rates(struct lbs_private *priv, lbs_pr_alert("Previously set fixed data rate %#x isn't " "compatible with the network.\n", priv->cur_rate); ret = -1; + goto done; } + ret = 0; + done: memset(rates, 0, *rates_size); *rates_size = min_t(int, tmp_size, *rates_size); @@ -320,7 +322,7 @@ static int lbs_associate(struct lbs_private *priv, rates = (struct mrvl_ie_rates_param_set *) pos; rates->header.type = cpu_to_le16(TLV_TYPE_RATES); memcpy(&rates->rates, &bss->rates, MAX_RATES); - tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES); + tmplen = MAX_RATES; if (get_common_rates(priv, rates->rates, &tmplen)) { ret = -1; goto done; @@ -596,7 +598,7 @@ static int lbs_adhoc_join(struct lbs_private *priv, /* Copy Data rates from the rates recorded in scan response */ memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates)); - ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES); + ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES); memcpy(cmd.bss.rates, bss->rates, ratesize); if (get_common_rates(priv, cmd.bss.rates, &ratesize)) { lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n"); -- cgit v1.2.3 From 1a67dde0abba36421a1257d01ba9de2f6d1c160a Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:41:49 +1000 Subject: md/raid5: Properly remove excess drives after shrinking a raid5/6 We were removing the drives, from the array, but not removing symlinks from /sys/.... and not marking the device as having been removed. Signed-off-by: NeilBrown --- drivers/md/raid5.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c index 94a74cb5cccb..b8a2c5dc67ba 100644 --- a/drivers/md/raid5.c +++ b/drivers/md/raid5.c @@ -5097,8 +5097,15 @@ static void raid5_finish_reshape(mddev_t *mddev) mddev->degraded--; for (d = conf->raid_disks ; d < conf->raid_disks - mddev->delta_disks; - d++) - raid5_remove_disk(mddev, d); + d++) { + mdk_rdev_t *rdev = conf->disks[d].rdev; + if (rdev && raid5_remove_disk(mddev, d) == 0) { + char nm[20]; + sprintf(nm, "rd%d", rdev->raid_disk); + sysfs_remove_link(&mddev->kobj, nm); + rdev->raid_disk = -1; + } + } } mddev->layout = conf->algorithm; mddev->chunk_sectors = conf->chunk_sectors; -- cgit v1.2.3 From 4d484a4a7a5126410eed5f8dd329a33f6eeed068 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Thu, 13 Aug 2009 10:41:50 +1000 Subject: md: allow upper limit for resync/reshape to be set when array is read-only Normally we only allow the upper limit for a reshape to be decreased when the array not performing a sync/recovery/reshape, otherwise there could be races. But if an array is part-way through a reshape when it is assembled the reshape is started immediately leaving no window to set an upper bound. If the array is started read-only, the reshape will be suspended until the array becomes writable, so that provides a window during which it is perfectly safe to reduce the upper limit of a reshape. So: allow the upper limit (sync_max) to be reduced even if the reshape thread is running, as long as the array is still read-only. Signed-off-by: NeilBrown --- drivers/md/md.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index d18805fea111..103f2d33fa89 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -3599,6 +3599,7 @@ max_sync_store(mddev_t *mddev, const char *buf, size_t len) if (max < mddev->resync_min) return -EINVAL; if (max < mddev->resync_max && + mddev->ro == 0 && test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)) return -EBUSY; -- cgit v1.2.3 From 839d1624b9dcf31fdc02e47359043bb7bd71d6ca Mon Sep 17 00:00:00 2001 From: Francois Romieu Date: Wed, 12 Aug 2009 22:18:14 -0700 Subject: 8139cp: balance dma_map_single vs dma_unmap_single pair The driver always: 1. allocate cp->rx_buf_sz + NET_IP_ALIGN 2. map cp->rx_buf_sz Signed-off-by: Francois Romieu Signed-off-by: David S. Miller --- drivers/net/8139cp.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c index 50efde11ea6c..d0dbbf39349a 100644 --- a/drivers/net/8139cp.c +++ b/drivers/net/8139cp.c @@ -515,7 +515,7 @@ rx_status_loop: dma_addr_t mapping; struct sk_buff *skb, *new_skb; struct cp_desc *desc; - unsigned buflen; + const unsigned buflen = cp->rx_buf_sz; skb = cp->rx_skb[rx_tail]; BUG_ON(!skb); @@ -549,8 +549,7 @@ rx_status_loop: pr_debug("%s: rx slot %d status 0x%x len %d\n", dev->name, rx_tail, status, len); - buflen = cp->rx_buf_sz + NET_IP_ALIGN; - new_skb = netdev_alloc_skb(dev, buflen); + new_skb = netdev_alloc_skb(dev, buflen + NET_IP_ALIGN); if (!new_skb) { dev->stats.rx_dropped++; goto rx_next; -- cgit v1.2.3 From 993e6f2fd487e2acddd711f79cf48f3420731382 Mon Sep 17 00:00:00 2001 From: Oliver Hartkopp Date: Tue, 11 Aug 2009 02:41:24 +0000 Subject: can: fix oops caused by wrong rtnl newlink usage For 'real' hardware CAN devices the netlink interface is used to set CAN specific communication parameters. Real CAN hardware can not be created with the ip tool ... The invocation of 'ip link add type can' lead to an oops as the standard rtnl newlink function was called: http://bugzilla.kernel.org/show_bug.cgi?id=13954 This patch adds a private newlink function for the CAN device driver interface that unconditionally returns -EOPNOTSUPP. Signed-off-by: Oliver Hartkopp Reported-by: Dmitry Eremin-Solenikov CC: Patrick McHardy CC: Wolfgang Grandegger Signed-off-by: David S. Miller --- drivers/net/can/dev.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers') diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c index 9e4283aff828..e1a4f8214239 100644 --- a/drivers/net/can/dev.c +++ b/drivers/net/can/dev.c @@ -611,11 +611,18 @@ nla_put_failure: return -EMSGSIZE; } +static int can_newlink(struct net_device *dev, + struct nlattr *tb[], struct nlattr *data[]) +{ + return -EOPNOTSUPP; +} + static struct rtnl_link_ops can_link_ops __read_mostly = { .kind = "can", .maxtype = IFLA_CAN_MAX, .policy = can_policy, .setup = can_setup, + .newlink = can_newlink, .changelink = can_changelink, .fill_info = can_fill_info, .fill_xstats = can_fill_xstats, -- cgit v1.2.3 From 237057ad3fe5644fa471be474a160de2fc2e5870 Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Tue, 11 Aug 2009 13:18:14 +0000 Subject: ixgbe: fix issues setting rx-usecs with legacy interrupts Currently setting rx-usecs when the interface is in legacy interrupt mode it is not immediate. We were only setting EITR for each MSIx vector and since this count would be zero for legacy mode it wasn't set until after a reset. This patch corrects that by checking what mode we are in and then setting EITR accordingly. Signed-off-by: Don Skidmore Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_ethtool.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 79144e950a34..dff8dfac7ed9 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1948,6 +1948,7 @@ static int ixgbe_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *ec) { struct ixgbe_adapter *adapter = netdev_priv(netdev); + struct ixgbe_q_vector *q_vector; int i; if (ec->tx_max_coalesced_frames_irq) @@ -1982,14 +1983,24 @@ static int ixgbe_set_coalesce(struct net_device *netdev, adapter->itr_setting = 0; } - for (i = 0; i < adapter->num_msix_vectors - NON_Q_VECTORS; i++) { - struct ixgbe_q_vector *q_vector = adapter->q_vector[i]; - if (q_vector->txr_count && !q_vector->rxr_count) - /* tx vector gets half the rate */ - q_vector->eitr = (adapter->eitr_param >> 1); - else - /* rx only or mixed */ - q_vector->eitr = adapter->eitr_param; + /* MSI/MSIx Interrupt Mode */ + if (adapter->flags & + (IXGBE_FLAG_MSIX_ENABLED | IXGBE_FLAG_MSI_ENABLED)) { + int num_vectors = adapter->num_msix_vectors - NON_Q_VECTORS; + for (i = 0; i < num_vectors; i++) { + q_vector = adapter->q_vector[i]; + if (q_vector->txr_count && !q_vector->rxr_count) + /* tx vector gets half the rate */ + q_vector->eitr = (adapter->eitr_param >> 1); + else + /* rx only or mixed */ + q_vector->eitr = adapter->eitr_param; + ixgbe_write_eitr(q_vector); + } + /* Legacy Interrupt Mode */ + } else { + q_vector = adapter->q_vector[0]; + q_vector->eitr = adapter->eitr_param; ixgbe_write_eitr(q_vector); } -- cgit v1.2.3 From e424fa9d6a0add1a9b812b07e3607daaa5b9e53d Mon Sep 17 00:00:00 2001 From: Amit Kumar Salecha Date: Thu, 13 Aug 2009 07:03:00 +0000 Subject: netxen: remove netxen workqueue o Remove private workqueue in the driver, move all scheduled tasks to keventd workqueues. This makes ports (interfaces) of same / different NIC boards independent, in terms of their link watchdog and reset tasks. o Move quick checks for link status and temperature in timer callback, schedule watchdog task only if link status changed or temperature reached critical threshold. This also fixes deadlock when thermal panic occurs, watchdog work was flushing workqueue that it was sitting on. Signed-off-by: Amit Kumar Salecha Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic.h | 2 +- drivers/net/netxen/netxen_nic_main.c | 69 +++++++++++++++++++++--------------- 2 files changed, 42 insertions(+), 29 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h index f86e05047d19..a9c1fcca5e75 100644 --- a/drivers/net/netxen/netxen_nic.h +++ b/drivers/net/netxen/netxen_nic.h @@ -1254,7 +1254,7 @@ struct netxen_adapter { u8 mc_enabled; u8 max_mc_count; u8 rss_supported; - u8 resv2; + u8 link_changed; u32 resv3; u8 has_link_events; diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index 70c05c4c0cab..d24e1cb93a26 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -94,10 +94,6 @@ static struct pci_device_id netxen_pci_tbl[] __devinitdata = { MODULE_DEVICE_TABLE(pci, netxen_pci_tbl); -static struct workqueue_struct *netxen_workq; -#define SCHEDULE_WORK(tp) queue_work(netxen_workq, tp) -#define FLUSH_SCHEDULED_WORK() flush_workqueue(netxen_workq) - static void netxen_watchdog(unsigned long); static uint32_t crb_cmd_producer[4] = { @@ -880,7 +876,6 @@ netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) spin_unlock(&adapter->tx_clean_lock); del_timer_sync(&adapter->watchdog_timer); - FLUSH_SCHEDULED_WORK(); } @@ -1177,6 +1172,9 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev) unregister_netdev(netdev); + cancel_work_sync(&adapter->watchdog_task); + cancel_work_sync(&adapter->tx_timeout_task); + if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) { netxen_nic_detach(adapter); } @@ -1211,6 +1209,9 @@ netxen_nic_suspend(struct pci_dev *pdev, pm_message_t state) if (netif_running(netdev)) netxen_nic_down(adapter, netdev); + cancel_work_sync(&adapter->watchdog_task); + cancel_work_sync(&adapter->tx_timeout_task); + if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) netxen_nic_detach(adapter); @@ -1549,11 +1550,6 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter) "%s: Device temperature %d degrees C exceeds" " maximum allowed. Hardware has been shut down.\n", netdev->name, temp_val); - - netif_device_detach(netdev); - netxen_nic_down(adapter, netdev); - netxen_nic_detach(adapter); - rv = 1; } else if (temp_state == NX_TEMP_WARN) { if (adapter->temp == NX_TEMP_NORMAL) { @@ -1587,10 +1583,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup) netif_carrier_off(netdev); netif_stop_queue(netdev); } - - if (!adapter->has_link_events) - netxen_nic_set_link_parameters(adapter); - + adapter->link_changed = !adapter->has_link_events; } else if (!adapter->ahw.linkup && linkup) { printk(KERN_INFO "%s: %s NIC Link is up\n", netxen_nic_driver_name, netdev->name); @@ -1599,9 +1592,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup) netif_carrier_on(netdev); netif_wake_queue(netdev); } - - if (!adapter->has_link_events) - netxen_nic_set_link_parameters(adapter); + adapter->link_changed = !adapter->has_link_events; } } @@ -1628,11 +1619,36 @@ static void netxen_nic_handle_phy_intr(struct netxen_adapter *adapter) netxen_advert_link_change(adapter, linkup); } +static void netxen_nic_thermal_shutdown(struct netxen_adapter *adapter) +{ + struct net_device *netdev = adapter->netdev; + + netif_device_detach(netdev); + netxen_nic_down(adapter, netdev); + netxen_nic_detach(adapter); +} + static void netxen_watchdog(unsigned long v) { struct netxen_adapter *adapter = (struct netxen_adapter *)v; - SCHEDULE_WORK(&adapter->watchdog_task); + if (netxen_nic_check_temp(adapter)) + goto do_sched; + + if (!adapter->has_link_events) { + netxen_nic_handle_phy_intr(adapter); + + if (adapter->link_changed) + goto do_sched; + } + + if (netif_running(adapter->netdev)) + mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); + + return; + +do_sched: + schedule_work(&adapter->watchdog_task); } void netxen_watchdog_task(struct work_struct *work) @@ -1640,11 +1656,13 @@ void netxen_watchdog_task(struct work_struct *work) struct netxen_adapter *adapter = container_of(work, struct netxen_adapter, watchdog_task); - if (netxen_nic_check_temp(adapter)) + if (adapter->temp == NX_TEMP_PANIC) { + netxen_nic_thermal_shutdown(adapter); return; + } - if (!adapter->has_link_events) - netxen_nic_handle_phy_intr(adapter); + if (adapter->link_changed) + netxen_nic_set_link_parameters(adapter); if (netif_running(adapter->netdev)) mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ); @@ -1652,9 +1670,8 @@ void netxen_watchdog_task(struct work_struct *work) static void netxen_tx_timeout(struct net_device *netdev) { - struct netxen_adapter *adapter = (struct netxen_adapter *) - netdev_priv(netdev); - SCHEDULE_WORK(&adapter->tx_timeout_task); + struct netxen_adapter *adapter = netdev_priv(netdev); + schedule_work(&adapter->tx_timeout_task); } static void netxen_tx_timeout_task(struct work_struct *work) @@ -1811,9 +1828,6 @@ static int __init netxen_init_module(void) { printk(KERN_INFO "%s\n", netxen_nic_driver_string); - if ((netxen_workq = create_singlethread_workqueue("netxen")) == NULL) - return -ENOMEM; - return pci_register_driver(&netxen_driver); } @@ -1822,7 +1836,6 @@ module_init(netxen_init_module); static void __exit netxen_exit_module(void) { pci_unregister_driver(&netxen_driver); - destroy_workqueue(netxen_workq); } module_exit(netxen_exit_module); -- cgit v1.2.3 From 232e7d68d50c9ac3a55d716e5ae215ecd1e043b9 Mon Sep 17 00:00:00 2001 From: Dhananjay Phadke Date: Thu, 13 Aug 2009 07:03:01 +0000 Subject: netxen: free napi resources during detach o Defer napi resouce allocation to device attach. o Free napi resources and delete napi during detach. This ensures right behavior across firmware reset. Signed-off-by: Dhananjay Phadke Signed-off-by: David S. Miller --- drivers/net/netxen/netxen_nic_init.c | 7 ------- drivers/net/netxen/netxen_nic_main.c | 32 ++++++++++++++++++++++++-------- 2 files changed, 24 insertions(+), 15 deletions(-) (limited to 'drivers') diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c index 7acf204e38c9..5d3343ef3d86 100644 --- a/drivers/net/netxen/netxen_nic_init.c +++ b/drivers/net/netxen/netxen_nic_init.c @@ -184,13 +184,6 @@ void netxen_free_sw_resources(struct netxen_adapter *adapter) kfree(recv_ctx->rds_rings); skip_rds: - if (recv_ctx->sds_rings == NULL) - goto skip_sds; - - for(ring = 0; ring < adapter->max_sds_rings; ring++) - recv_ctx->sds_rings[ring].consumer = 0; - -skip_sds: if (adapter->tx_ring == NULL) return; diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index d24e1cb93a26..28f270f5ac78 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -167,6 +167,8 @@ netxen_free_sds_rings(struct netxen_recv_context *recv_ctx) { if (recv_ctx->sds_rings != NULL) kfree(recv_ctx->sds_rings); + + recv_ctx->sds_rings = NULL; } static int @@ -188,6 +190,21 @@ netxen_napi_add(struct netxen_adapter *adapter, struct net_device *netdev) return 0; } +static void +netxen_napi_del(struct netxen_adapter *adapter) +{ + int ring; + struct nx_host_sds_ring *sds_ring; + struct netxen_recv_context *recv_ctx = &adapter->recv_ctx; + + for (ring = 0; ring < adapter->max_sds_rings; ring++) { + sds_ring = &recv_ctx->sds_rings[ring]; + netif_napi_del(&sds_ring->napi); + } + + netxen_free_sds_rings(&adapter->recv_ctx); +} + static void netxen_napi_enable(struct netxen_adapter *adapter) { @@ -889,10 +906,12 @@ netxen_nic_attach(struct netxen_adapter *adapter) struct nx_host_tx_ring *tx_ring; err = netxen_init_firmware(adapter); - if (err != 0) { - printk(KERN_ERR "Failed to init firmware\n"); - return -EIO; - } + if (err) + return err; + + err = netxen_napi_add(adapter, netdev); + if (err) + return err; if (adapter->fw_major < 4) adapter->max_rds_rings = 3; @@ -956,6 +975,7 @@ netxen_nic_detach(struct netxen_adapter *adapter) netxen_free_hw_resources(adapter); netxen_release_rx_buffers(adapter); netxen_nic_free_irq(adapter); + netxen_napi_del(adapter); netxen_free_sw_resources(adapter); adapter->is_up = 0; @@ -1100,9 +1120,6 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent) netdev->irq = adapter->msix_entries[0].vector; - if (netxen_napi_add(adapter, netdev)) - goto err_out_disable_msi; - init_timer(&adapter->watchdog_timer); adapter->watchdog_timer.function = &netxen_watchdog; adapter->watchdog_timer.data = (unsigned long)adapter; @@ -1183,7 +1200,6 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev) netxen_free_adapter_offload(adapter); netxen_teardown_intr(adapter); - netxen_free_sds_rings(&adapter->recv_ctx); netxen_cleanup_pci_map(adapter); -- cgit v1.2.3 From 5b766182a110311fbf618f736bc8a8f2f7ce3f4c Mon Sep 17 00:00:00 2001 From: Antonio Ospite Date: Wed, 22 Jul 2009 17:20:50 -0300 Subject: V4L/DVB (12330): pxa_camera: Fix Oops in pxa_camera_probe mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized. Signed-off-by: Antonio Ospite Signed-off-by: Guennadi Liakhovetski Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/pxa_camera.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c index 46e0d8ad880f..e048d25798cc 100644 --- a/drivers/media/video/pxa_camera.c +++ b/drivers/media/video/pxa_camera.c @@ -1579,6 +1579,7 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev) pcdev->mclk = 20000000; } + pcdev->soc_host.dev = &pdev->dev; pcdev->mclk_divisor = mclk_get_divisor(pcdev); INIT_LIST_HEAD(&pcdev->capture); @@ -1644,7 +1645,6 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev) pcdev->soc_host.drv_name = PXA_CAM_DRV_NAME; pcdev->soc_host.ops = &pxa_soc_camera_host_ops; pcdev->soc_host.priv = pcdev; - pcdev->soc_host.dev = &pdev->dev; pcdev->soc_host.nr = pdev->id; err = soc_camera_host_register(&pcdev->soc_host); -- cgit v1.2.3 From ed18d0c87ee0ab6e0985d83c19cd135b1bd54998 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Thu, 23 Jul 2009 21:46:57 -0300 Subject: V4L/DVB (12337): ivtv: Read buffer overflow This mistakenly tests against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Signed-off-by: Roel Kluin Signed-off-by: Andy Walls Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/ivtv/ivtv-controls.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/ivtv/ivtv-controls.c b/drivers/media/video/ivtv/ivtv-controls.c index a3b77ed3f089..4a9c8ce0ecb3 100644 --- a/drivers/media/video/ivtv/ivtv-controls.c +++ b/drivers/media/video/ivtv/ivtv-controls.c @@ -17,6 +17,7 @@ along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ +#include #include "ivtv-driver.h" #include "ivtv-cards.h" @@ -281,7 +282,7 @@ int ivtv_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c) idx = p.audio_properties & 0x03; /* The audio clock of the digitizer must match the codec sample rate otherwise you get some very strange effects. */ - if (idx < sizeof(freqs)) + if (idx < ARRAY_SIZE(freqs)) ivtv_call_all(itv, audio, s_clock_freq, freqs[idx]); return err; } -- cgit v1.2.3 From 225aeb1c5863bc92c6bb1f921e9a6cf4d15dbb2a Mon Sep 17 00:00:00 2001 From: Andy Walls Date: Thu, 23 Jul 2009 21:51:29 -0300 Subject: V4L/DVB (12338): cx18: Read buffer overflow This mistakenly tested against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Reported-by: Roel Kluin Signed-off-by: Andy Walls Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx18/cx18-controls.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/cx18/cx18-controls.c b/drivers/media/video/cx18/cx18-controls.c index 5136df198338..93f0dae01350 100644 --- a/drivers/media/video/cx18/cx18-controls.c +++ b/drivers/media/video/cx18/cx18-controls.c @@ -20,6 +20,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA * 02111-1307 USA */ +#include #include "cx18-driver.h" #include "cx18-cards.h" @@ -317,7 +318,7 @@ int cx18_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c) idx = p.audio_properties & 0x03; /* The audio clock of the digitizer must match the codec sample rate otherwise you get some very strange effects. */ - if (idx < sizeof(freqs)) + if (idx < ARRAY_SIZE(freqs)) cx18_call_all(cx, audio, s_clock_freq, freqs[idx]); return err; } -- cgit v1.2.3 From 296544e15a7126373851abd40acc526b79b91432 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 27 Jul 2009 08:24:29 -0300 Subject: V4L/DVB (12340): mtv9v011: Add a missing chip version to the driver Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From the revision history at the mt9v011 datasheet, it seems that the chip version has changed from the first release of the chip. Thanks-to hermann pitton for pointing this to me, on his tests with a Silvercrest webcam. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 3 ++- drivers/media/video/mt9v011.c | 14 +++++++++----- drivers/media/video/mt9v011.h | 3 ++- 3 files changed, 13 insertions(+), 7 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 320f1f60276e..bc213a1f9c1f 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1771,7 +1771,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) version = be16_to_cpu(version_be); switch (version) { - case 0x8243: /* mt9v011 640x480 1.3 Mpix sensor */ + case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */ + case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index b2260de645f0..c14bf47d6928 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -393,10 +393,13 @@ static int mt9v011_s_register(struct v4l2_subdev *sd, static int mt9v011_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) { + u16 version; struct i2c_client *client = v4l2_get_subdevdata(sd); + version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION); + return v4l2_chip_ident_i2c_client(client, chip, V4L2_IDENT_MT9V011, - MT9V011_VERSION); + version); } static const struct v4l2_subdev_core_ops mt9v011_core_ops = { @@ -449,8 +452,9 @@ static int mt9v011_probe(struct i2c_client *c, /* Check if the sensor is really a MT9V011 */ version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION); - if (version != MT9V011_VERSION) { - v4l2_info(sd, "*** unknown micron chip detected (0x%04x.\n", + if ((version != MT9V011_VERSION) && + (version != MT9V011_REV_B_VERSION)) { + v4l2_info(sd, "*** unknown micron chip detected (0x%04x).\n", version); kfree(core); return -EINVAL; @@ -461,8 +465,8 @@ static int mt9v011_probe(struct i2c_client *c, core->height = 480; core->xtal = 27000000; /* Hz */ - v4l_info(c, "chip found @ 0x%02x (%s)\n", - c->addr << 1, c->adapter->name); + v4l_info(c, "chip found @ 0x%02x (%s - chip version 0x%04x)\n", + c->addr << 1, c->adapter->name, version); return 0; } diff --git a/drivers/media/video/mt9v011.h b/drivers/media/video/mt9v011.h index 9e443ee30558..3350fd6083c3 100644 --- a/drivers/media/video/mt9v011.h +++ b/drivers/media/video/mt9v011.h @@ -30,6 +30,7 @@ #define R35_MT9V011_GLOBAL_GAIN 0x35 #define RF1_MT9V011_CHIP_ENABLE 0xf1 -#define MT9V011_VERSION 0x8243 +#define MT9V011_VERSION 0x8232 +#define MT9V011_REV_B_VERSION 0x8243 #endif -- cgit v1.2.3 From 458f9aa391efd34867f8cabac2e2f1af00cbc562 Mon Sep 17 00:00:00 2001 From: Jan Nikitenko Date: Thu, 18 Jun 2009 08:11:57 -0300 Subject: V4L/DVB (12341): zl10353 and qt1010: fix stack corruption bug Fixes stack corruption bug present in dump_regs function of zl10353 and qt1010 drivers: the buffer buf was one byte smaller than required - there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom bytes per line and 1 byte for zero ending the string required, i.e. 53 bytes, but only 52 were provided. The one byte missing in stack based buffer buf can cause stack corruption possibly leading to kernel oops, as discovered originally with af9015 driver (af9015: fix stack corruption bug). Signed-off-by: Jan Nikitenko Signed-off-by: Mauro Carvalho Chehab --- drivers/media/common/tuners/qt1010.c | 12 +++++------- drivers/media/dvb/frontends/zl10353.c | 12 +++++------- 2 files changed, 10 insertions(+), 14 deletions(-) (limited to 'drivers') diff --git a/drivers/media/common/tuners/qt1010.c b/drivers/media/common/tuners/qt1010.c index 825aa1412e6f..9f5dba244cb8 100644 --- a/drivers/media/common/tuners/qt1010.c +++ b/drivers/media/common/tuners/qt1010.c @@ -64,24 +64,22 @@ static int qt1010_writereg(struct qt1010_priv *priv, u8 reg, u8 val) /* dump all registers */ static void qt1010_dump_regs(struct qt1010_priv *priv) { - char buf[52], buf2[4]; u8 reg, val; for (reg = 0; ; reg++) { if (reg % 16 == 0) { if (reg) - printk("%s\n", buf); - sprintf(buf, "%02x: ", reg); + printk(KERN_CONT "\n"); + printk(KERN_DEBUG "%02x:", reg); } if (qt1010_readreg(priv, reg, &val) == 0) - sprintf(buf2, "%02x ", val); + printk(KERN_CONT " %02x", val); else - strcpy(buf2, "-- "); - strcat(buf, buf2); + printk(KERN_CONT " --"); if (reg == 0x2f) break; } - printk("%s\n", buf); + printk(KERN_CONT "\n"); } static int qt1010_set_params(struct dvb_frontend *fe, diff --git a/drivers/media/dvb/frontends/zl10353.c b/drivers/media/dvb/frontends/zl10353.c index 148b6f7f6cb2..66f5c1fb3074 100644 --- a/drivers/media/dvb/frontends/zl10353.c +++ b/drivers/media/dvb/frontends/zl10353.c @@ -98,7 +98,6 @@ static int zl10353_read_register(struct zl10353_state *state, u8 reg) static void zl10353_dump_regs(struct dvb_frontend *fe) { struct zl10353_state *state = fe->demodulator_priv; - char buf[52], buf2[4]; int ret; u8 reg; @@ -106,19 +105,18 @@ static void zl10353_dump_regs(struct dvb_frontend *fe) for (reg = 0; ; reg++) { if (reg % 16 == 0) { if (reg) - printk(KERN_DEBUG "%s\n", buf); - sprintf(buf, "%02x: ", reg); + printk(KERN_CONT "\n"); + printk(KERN_DEBUG "%02x:", reg); } ret = zl10353_read_register(state, reg); if (ret >= 0) - sprintf(buf2, "%02x ", (u8)ret); + printk(KERN_CONT " %02x", (u8)ret); else - strcpy(buf2, "-- "); - strcat(buf, buf2); + printk(KERN_CONT " --"); if (reg == 0xff) break; } - printk(KERN_DEBUG "%s\n", buf); + printk(KERN_CONT "\n"); } static void zl10353_calc_nominal_rate(struct dvb_frontend *fe, -- cgit v1.2.3 From 0a6e44d1beb30813f62ad376a31694e637858328 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Wed, 29 Jul 2009 01:39:12 -0300 Subject: V4L/DVB (12344): em28xx: fix support for Plextor ConvertX PX-TV100U This device uses msp34xx and uses 2.048 MHz frequency for I2S communication. Thanks to Angelo Cano for pointing the issues with this device and proposing an approach for fixing the issue. Tested-by: Angelo Cano Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index bc213a1f9c1f..d0b033bce867 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -622,22 +622,27 @@ struct em28xx_board em28xx_boards[] = { }, [EM2861_BOARD_PLEXTOR_PX_TV100U] = { .name = "Plextor ConvertX PX-TV100U", - .valid = EM28XX_BOARD_NOT_VALIDATED, .tuner_type = TUNER_TNF_5335MF, + .xclk = EM28XX_XCLK_I2S_MSB_TIMING | + EM28XX_XCLK_FREQUENCY_12MHZ, .tda9887_conf = TDA9887_PRESENT, .decoder = EM28XX_TVP5150, + .has_msp34xx = 1, .input = { { .type = EM28XX_VMUX_TELEVISION, .vmux = TVP5150_COMPOSITE0, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_COMPOSITE1, .vmux = TVP5150_COMPOSITE1, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, }, { .type = EM28XX_VMUX_SVIDEO, .vmux = TVP5150_SVIDEO, .amux = EM28XX_AMUX_LINE_IN, + .gpio = pinnacle_hybrid_pro_analog, } }, }, @@ -1877,9 +1882,8 @@ void em28xx_pre_card_setup(struct em28xx *dev) /* request some modules */ switch (dev->model) { case EM2861_BOARD_PLEXTOR_PX_TV100U: - /* FIXME guess */ - /* Turn on analog audio output */ - em28xx_write_reg(dev, EM28XX_R08_GPIO, 0xfd); + /* Sets the msp34xx I2S speed */ + dev->i2s_speed = 2048000; break; case EM2861_BOARD_KWORLD_PVRTV_300U: case EM2880_BOARD_KWORLD_DVB_305U: -- cgit v1.2.3 From 337ab6d34f0be7cfbfb5ac8cb651276fc58aa20d Mon Sep 17 00:00:00 2001 From: Sohail Syyed Date: Sun, 26 Jul 2009 11:06:20 -0300 Subject: V4L/DVB (12349): cx88: HVR1300 ensure switching from Encoder to DVB-T and back is reliable Current tip is broken and does not switch back to DVB-T correctly Signed-off-by: Sohail Syyed Signed-off-by: Steven Toth Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx88/cx88-mpeg.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/cx88/cx88-mpeg.c b/drivers/media/video/cx88/cx88-mpeg.c index da4e3912cd37..7172dcf2a4fa 100644 --- a/drivers/media/video/cx88/cx88-mpeg.c +++ b/drivers/media/video/cx88/cx88-mpeg.c @@ -116,6 +116,10 @@ static int cx8802_start_dma(struct cx8802_dev *dev, udelay(100); break; case CX88_BOARD_HAUPPAUGE_HVR1300: + /* Enable MPEG parallel IO and video signal pins */ + cx_write(MO_PINMUX_IO, 0x88); + cx_write(TS_SOP_STAT, 0); + cx_write(TS_VALERR_CNTRL, 0); break; case CX88_BOARD_PINNACLE_PCTV_HD_800i: /* Enable MPEG parallel IO and video signal pins */ -- cgit v1.2.3 From 6655be0f4f377d7e249219c6031c4be3533604a2 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 20 Jul 2009 12:20:58 -0300 Subject: V4L/DVB (12362): cx23885-417: fix manipulation of tvnorms Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of the norm passed. This patch sets cx23885_mpeg_template.tvnorms and cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work. Thanks to Joseph Yasi for pointing this out, even though this particular fix was already pushed into a development repository, merge priority of this changeset has been escalated as a result of Joseph posting this identical patch. Signed-off-by: Michael Krufky Signed-off-by: Joseph A. Yasi Reviewed-by: Steven Toth Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx23885/cx23885-417.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c index e0cf21e0b1bf..1a1048b18f70 100644 --- a/drivers/media/video/cx23885/cx23885-417.c +++ b/drivers/media/video/cx23885/cx23885-417.c @@ -1715,6 +1715,8 @@ static struct video_device cx23885_mpeg_template = { .fops = &mpeg_fops, .ioctl_ops = &mpeg_ioctl_ops, .minor = -1, + .tvnorms = CX23885_NORMS, + .current_norm = V4L2_STD_NTSC_M, }; void cx23885_417_unregister(struct cx23885_dev *dev) -- cgit v1.2.3 From ba1bc64272f0af668690ba2bf859b13172db7230 Mon Sep 17 00:00:00 2001 From: Nils Kassube Date: Tue, 28 Jul 2009 11:54:52 -0300 Subject: V4L/DVB (12371): af9015: Fix for crash in dvb-usb-af9015 Moving BOOT fixes problem. Signed-off-by: Nils Kassube Acked-by: Antti Palosaari Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/dvb-usb/af9015.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/dvb/dvb-usb/af9015.c b/drivers/media/dvb/dvb-usb/af9015.c index 4cb31e7c13c2..26690dfb3260 100644 --- a/drivers/media/dvb/dvb-usb/af9015.c +++ b/drivers/media/dvb/dvb-usb/af9015.c @@ -81,7 +81,6 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req) switch (req->cmd) { case GET_CONFIG: - case BOOT: case READ_MEMORY: case RECONNECT_USB: case GET_IR_CODE: @@ -100,6 +99,7 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req) case WRITE_VIRTUAL_MEMORY: case COPY_FIRMWARE: case DOWNLOAD_FIRMWARE: + case BOOT: break; default: err("unknown command:%d", req->cmd); -- cgit v1.2.3 From d1ae4e1d05cc982b6b480c1a3d69b8bb231e3493 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 12 Jul 2009 18:25:45 -0300 Subject: V4L/DVB (12374): sms1xxx: fix broken Hauppauge devices The current GPIO configuration breaks all Hauppauge devices. The code being removed affects Hauppauge devices only, and is the cause of the breakage. Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/sms-cards.c | 100 ------------------------------------ 1 file changed, 100 deletions(-) (limited to 'drivers') diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c index d8b15d583bde..76bd3cb82d9f 100644 --- a/drivers/media/dvb/siano/sms-cards.c +++ b/drivers/media/dvb/siano/sms-cards.c @@ -124,91 +124,15 @@ int sms_board_event(struct smscore_device_t *coredev, switch (gevent) { case BOARD_EVENT_POWER_INIT: /* including hotplug */ - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - /* set I/O and turn off all LEDs */ - smscore_gpio_configure(coredev, - board->board_cfg.leds_power, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 0); - smscore_gpio_configure(coredev, board->board_cfg.led0, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 0); - smscore_gpio_configure(coredev, board->board_cfg.led1, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - /* set I/O and turn off LNA */ - smscore_gpio_configure(coredev, - board->board_cfg.foreign_lna0_ctrl, - &MyGpioConfig); - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 0); - break; - } break; /* BOARD_EVENT_BIND */ case BOARD_EVENT_POWER_SUSPEND: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 0); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 0); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 0); - break; - } break; /* BOARD_EVENT_POWER_SUSPEND */ case BOARD_EVENT_POWER_RESUME: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 1); - break; - } break; /* BOARD_EVENT_POWER_RESUME */ case BOARD_EVENT_BIND: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.leds_power, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led0, 1); - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2: - case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD: - smscore_gpio_set_level(coredev, - board->board_cfg.foreign_lna0_ctrl, - 1); - break; - } break; /* BOARD_EVENT_BIND */ case BOARD_EVENT_SCAN_PROG: @@ -218,20 +142,8 @@ int sms_board_event(struct smscore_device_t *coredev, case BOARD_EVENT_EMERGENCY_WARNING_SIGNAL: break; /* BOARD_EVENT_EMERGENCY_WARNING_SIGNAL */ case BOARD_EVENT_FE_LOCK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 1); - break; - } break; /* BOARD_EVENT_FE_LOCK */ case BOARD_EVENT_FE_UNLOCK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - } break; /* BOARD_EVENT_FE_UNLOCK */ case BOARD_EVENT_DEMOD_LOCK: break; /* BOARD_EVENT_DEMOD_LOCK */ @@ -248,20 +160,8 @@ int sms_board_event(struct smscore_device_t *coredev, case BOARD_EVENT_RECEPTION_LOST_0: break; /* BOARD_EVENT_RECEPTION_LOST_0 */ case BOARD_EVENT_MULTIPLEX_OK: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 1); - break; - } break; /* BOARD_EVENT_MULTIPLEX_OK */ case BOARD_EVENT_MULTIPLEX_ERRORS: - switch (board_id) { - case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM: - smscore_gpio_set_level(coredev, - board->board_cfg.led1, 0); - break; - } break; /* BOARD_EVENT_MULTIPLEX_ERRORS */ default: -- cgit v1.2.3 From d79cd8393ae85ebaf53a8fc93491eea96522d68e Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Sun, 19 Jul 2009 19:16:05 -0300 Subject: V4L/DVB (12328): uvcvideo: Don't apply the FIX_BANDWIDTH quirk to all ViMicro devices Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10 netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro devices, list the devices explicitly. Signed-off-by: Laurent Pinchart Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/uvc/uvc_driver.c | 24 +++++++++++++++++++++--- 1 file changed, 21 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/uvc/uvc_driver.c b/drivers/media/video/uvc/uvc_driver.c index 89927b7aec28..04b47832fa0a 100644 --- a/drivers/media/video/uvc/uvc_driver.c +++ b/drivers/media/video/uvc/uvc_driver.c @@ -1845,11 +1845,29 @@ static struct usb_device_id uvc_ids[] = { .bInterfaceSubClass = 1, .bInterfaceProtocol = 0, .driver_info = UVC_QUIRK_STREAM_NO_FID }, - /* ViMicro */ - { .match_flags = USB_DEVICE_ID_MATCH_VENDOR + /* ViMicro Vega */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE + | USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x0ac8, + .idProduct = 0x332d, + .bInterfaceClass = USB_CLASS_VIDEO, + .bInterfaceSubClass = 1, + .bInterfaceProtocol = 0, + .driver_info = UVC_QUIRK_FIX_BANDWIDTH }, + /* ViMicro - Minoru3D */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE + | USB_DEVICE_ID_MATCH_INT_INFO, + .idVendor = 0x0ac8, + .idProduct = 0x3410, + .bInterfaceClass = USB_CLASS_VIDEO, + .bInterfaceSubClass = 1, + .bInterfaceProtocol = 0, + .driver_info = UVC_QUIRK_FIX_BANDWIDTH }, + /* ViMicro Venus - Minoru3D */ + { .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_INT_INFO, .idVendor = 0x0ac8, - .idProduct = 0x0000, + .idProduct = 0x3420, .bInterfaceClass = USB_CLASS_VIDEO, .bInterfaceSubClass = 1, .bInterfaceProtocol = 0, -- cgit v1.2.3 From bd0232c13419b7ce51e02942082ff6af231e0f84 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Sat, 1 Aug 2009 18:14:24 -0300 Subject: V4L/DVB (12380): uvcvideo: Avoid flooding the kernel log with "unknown event type" messages The iSight sends non-UVC status events through the interrupt endpoint. Those invalid events are reported to the kernel log, resulting in a log flood. Only log the events when the UVC_TRACE_STATUS flag is set. Signed-off-by: Laurent Pinchart Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/uvc/uvc_status.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/uvc/uvc_status.c b/drivers/media/video/uvc/uvc_status.c index f152a9903862..1ca6dff73612 100644 --- a/drivers/media/video/uvc/uvc_status.c +++ b/drivers/media/video/uvc/uvc_status.c @@ -145,8 +145,8 @@ static void uvc_status_complete(struct urb *urb) break; default: - uvc_printk(KERN_INFO, "unknown event type %u.\n", - dev->status[0]); + uvc_trace(UVC_TRACE_STATUS, "Unknown status event " + "type %u.\n", dev->status[0]); break; } } -- cgit v1.2.3 From 79a6382551507ce196c3b4296e32b5386cdfbf15 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Sun, 2 Aug 2009 12:37:34 -0300 Subject: V4L/DVB (12386): sms1xxx: fix build warning: unused variable 'board' Remove the following build warning: sms-cards.c: In function 'sms_board_event': sms-cards.c:120: warning: unused variable 'board' Thanks to Hans Verkuil for pointing this out. The problem code has been #if 0'd for now, this will likely be used again in the future, once the event interface is complete. Cc: Hans Verkuil Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/sms-cards.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c index 76bd3cb82d9f..0420e2885e75 100644 --- a/drivers/media/dvb/siano/sms-cards.c +++ b/drivers/media/dvb/siano/sms-cards.c @@ -116,8 +116,6 @@ static inline void sms_gpio_assign_11xx_default_led_config( int sms_board_event(struct smscore_device_t *coredev, enum SMS_BOARD_EVENTS gevent) { - int board_id = smscore_get_board_id(coredev); - struct sms_board *board = sms_get_board(board_id); struct smscore_gpio_config MyGpioConfig; sms_gpio_assign_11xx_default_led_config(&MyGpioConfig); -- cgit v1.2.3 From b5f05064b556da5183adc383e5f8d50af0392849 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 3 Aug 2009 16:51:33 -0300 Subject: V4L/DVB (12390): saa7134: Use correct product name for Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.saa7134 | 2 +- drivers/media/video/saa7134/saa7134-cards.c | 20 ++++++++++---------- drivers/media/video/saa7134/saa7134-dvb.c | 2 +- drivers/media/video/saa7134/saa7134.h | 2 +- 4 files changed, 13 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index 15562427e8a9..a82b767f9e7a 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -153,7 +153,7 @@ 152 -> Asus Tiger Rev:1.00 [1043:4857] 153 -> Kworld Plus TV Analog Lite PCI [17de:7128] 154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d] -155 -> Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid [0070:6706,0070:6708] +155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid [0070:6706,0070:6708] 156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] 157 -> Avermedia AVerTV Studio 507UA [1461:a11b] 158 -> AVerMedia Cardbus TV/Radio (E501R) [1461:b7e9] diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c index 06861b782b95..60e74ad59679 100644 --- a/drivers/media/video/saa7134/saa7134-cards.c +++ b/drivers/media/video/saa7134/saa7134-cards.c @@ -3331,8 +3331,8 @@ struct saa7134_board saa7134_boards[] = { .gpio = 0x0200100, }, }, - [SAA7134_BOARD_HAUPPAUGE_HVR1120] = { - .name = "Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid", + [SAA7134_BOARD_HAUPPAUGE_HVR1150] = { + .name = "Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid", .audio_clock = 0x00187de7, .tuner_type = TUNER_PHILIPS_TDA8290, .radio_type = UNSET, @@ -5862,7 +5862,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6706, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1150, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -5874,7 +5874,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6708, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1150, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -6363,7 +6363,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev, switch (command) { case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */ switch (dev->board) { - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg); break; @@ -6384,7 +6384,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev, int ret; switch (dev->board) { - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: /* tda8290 + tda18271 */ ret = saa7134_tda8290_18271_callback(dev, command, arg); @@ -6427,7 +6427,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data) switch (tv.model) { case 67019: /* WinTV-HVR1110 (Retail, IR Blaster, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67109: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */ - case 67201: /* WinTV-HVR1120 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ + case 67201: /* WinTV-HVR1150 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67301: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */ case 67209: /* WinTV-HVR1110 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */ case 67559: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ @@ -6435,7 +6435,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data) case 67579: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM) */ case 67589: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */ case 67599: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */ - case 67651: /* WinTV-HVR1120 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ + case 67651: /* WinTV-HVR1150 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ case 67659: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */ break; default: @@ -6625,7 +6625,7 @@ int saa7134_board_init1(struct saa7134_dev *dev) saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00); break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: /* GPIO 26 high for digital, low for analog */ saa7134_set_gpio(dev, 26, 0); @@ -6891,7 +6891,7 @@ int saa7134_board_init2(struct saa7134_dev *dev) dev->name, saa7134_boards[dev->board].name); } break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: hauppauge_eeprom(dev, dev->eedata+0x80); break; diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c index 31930f26ffc7..ae0a7ecc46d9 100644 --- a/drivers/media/video/saa7134/saa7134-dvb.c +++ b/drivers/media/video/saa7134/saa7134-dvb.c @@ -1147,7 +1147,7 @@ static int dvb_init(struct saa7134_dev *dev) &tda827x_cfg_1) < 0) goto dettach_frontend; break; - case SAA7134_BOARD_HAUPPAUGE_HVR1120: + case SAA7134_BOARD_HAUPPAUGE_HVR1150: fe0->dvb.frontend = dvb_attach(lgdt3305_attach, &hcw_lgdt3305_config, &dev->i2c_adap); diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h index 82268848f26a..bad5b237f21f 100644 --- a/drivers/media/video/saa7134/saa7134.h +++ b/drivers/media/video/saa7134/saa7134.h @@ -278,7 +278,7 @@ struct saa7134_format { #define SAA7134_BOARD_ASUSTeK_TIGER 152 #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154 -#define SAA7134_BOARD_HAUPPAUGE_HVR1120 155 +#define SAA7134_BOARD_HAUPPAUGE_HVR1150 155 #define SAA7134_BOARD_HAUPPAUGE_HVR1110R3 156 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158 -- cgit v1.2.3 From 0e316ecfc851c8dd955d9fa6e0d3a46e451a46f4 Mon Sep 17 00:00:00 2001 From: Michael Krufky Date: Mon, 3 Aug 2009 16:51:33 -0300 Subject: V4L/DVB (12391): saa7134: Use correct product name for Hauppauge WinTV-HVR1120 DVB-T/Hybrid Signed-off-by: Michael Krufky Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.saa7134 | 2 +- drivers/media/video/saa7134/saa7134-cards.c | 18 +++++++++--------- drivers/media/video/saa7134/saa7134-dvb.c | 2 +- drivers/media/video/saa7134/saa7134.h | 2 +- 4 files changed, 12 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134 index a82b767f9e7a..c913e5614195 100644 --- a/Documentation/video4linux/CARDLIST.saa7134 +++ b/Documentation/video4linux/CARDLIST.saa7134 @@ -154,7 +154,7 @@ 153 -> Kworld Plus TV Analog Lite PCI [17de:7128] 154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d] 155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid [0070:6706,0070:6708] -156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] +156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a] 157 -> Avermedia AVerTV Studio 507UA [1461:a11b] 158 -> AVerMedia Cardbus TV/Radio (E501R) [1461:b7e9] 159 -> Beholder BeholdTV 505 RDS [0000:505B] diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c index 60e74ad59679..6eebe3ef97d3 100644 --- a/drivers/media/video/saa7134/saa7134-cards.c +++ b/drivers/media/video/saa7134/saa7134-cards.c @@ -3363,8 +3363,8 @@ struct saa7134_board saa7134_boards[] = { .gpio = 0x0800100, /* GPIO 23 HI for FM */ }, }, - [SAA7134_BOARD_HAUPPAUGE_HVR1110R3] = { - .name = "Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid", + [SAA7134_BOARD_HAUPPAUGE_HVR1120] = { + .name = "Hauppauge WinTV-HVR1120 DVB-T/Hybrid", .audio_clock = 0x00187de7, .tuner_type = TUNER_PHILIPS_TDA8290, .radio_type = UNSET, @@ -5868,7 +5868,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6707, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -5880,13 +5880,13 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x6709, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x0070, .subdevice = 0x670a, - .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1110R3, + .driver_data = SAA7134_BOARD_HAUPPAUGE_HVR1120, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -6364,7 +6364,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev, case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */ switch (dev->board) { case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg); break; default: @@ -6385,7 +6385,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev, switch (dev->board) { case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: /* tda8290 + tda18271 */ ret = saa7134_tda8290_18271_callback(dev, command, arg); break; @@ -6626,7 +6626,7 @@ int saa7134_board_init1(struct saa7134_dev *dev) saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00); break; case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: /* GPIO 26 high for digital, low for analog */ saa7134_set_gpio(dev, 26, 0); msleep(1); @@ -6892,7 +6892,7 @@ int saa7134_board_init2(struct saa7134_dev *dev) } break; case SAA7134_BOARD_HAUPPAUGE_HVR1150: - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: hauppauge_eeprom(dev, dev->eedata+0x80); break; case SAA7134_BOARD_HAUPPAUGE_HVR1110: diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c index ae0a7ecc46d9..98f3efd1e944 100644 --- a/drivers/media/video/saa7134/saa7134-dvb.c +++ b/drivers/media/video/saa7134/saa7134-dvb.c @@ -1119,7 +1119,7 @@ static int dvb_init(struct saa7134_dev *dev) &tda827x_cfg_2) < 0) goto dettach_frontend; break; - case SAA7134_BOARD_HAUPPAUGE_HVR1110R3: + case SAA7134_BOARD_HAUPPAUGE_HVR1120: fe0->dvb.frontend = dvb_attach(tda10048_attach, &hcw_tda10048_config, &dev->i2c_adap); diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h index bad5b237f21f..fb564f14887c 100644 --- a/drivers/media/video/saa7134/saa7134.h +++ b/drivers/media/video/saa7134/saa7134.h @@ -279,7 +279,7 @@ struct saa7134_format { #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154 #define SAA7134_BOARD_HAUPPAUGE_HVR1150 155 -#define SAA7134_BOARD_HAUPPAUGE_HVR1110R3 156 +#define SAA7134_BOARD_HAUPPAUGE_HVR1120 156 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158 #define SAA7134_BOARD_BEHOLD_505RDS 159 -- cgit v1.2.3 From 11db906983fc6e996fcd10073843bd6f1b9a96c3 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Mon, 3 Aug 2009 22:40:16 -0300 Subject: V4L/DVB (12393): cx88: fix regression in tuning for Geniatech X8000 MT The introduction of the zl10353 i2c gate control broke support for the Geniatech board (which is not behind an i2 gate). Add the needed parameter. Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/cx88/cx88-dvb.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/media/video/cx88/cx88-dvb.c b/drivers/media/video/cx88/cx88-dvb.c index c44e87600219..e237b507659b 100644 --- a/drivers/media/video/cx88/cx88-dvb.c +++ b/drivers/media/video/cx88/cx88-dvb.c @@ -501,6 +501,7 @@ static struct zl10353_config cx88_pinnacle_hybrid_pctv = { static struct zl10353_config cx88_geniatech_x8000_mt = { .demod_address = (0x1e >> 1), .no_tuner = 1, + .disable_i2c_gate_ctrl = 1, }; static struct s5h1411_config dvico_fusionhdtv7_config = { -- cgit v1.2.3 From 93b999239c418cf5c668fd966ac2c5c27b8180dd Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Mon, 3 Aug 2009 22:52:59 -0300 Subject: V4L/DVB (12394): cx88: Disable xc3028 power management for Geniatech x8000 A user discovered that the Geniatech x8000 encountered a regression when the xc3028 power management was introduced. The xc3028 never recovers after setting the powerdown register, which is probably because the xc3028 reset GPIO is not properly configured. Since I do not have access to the hardware and thus cannot determine the correct GPIO configuration, just disable xc3028 power management on this board, which fixes the regression. Thanks to user "ritec" for reporting the issue and testing the fix. Cc: rictec Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/common/tuners/tuner-xc2028.c | 4 ++-- drivers/media/common/tuners/tuner-xc2028.h | 1 + drivers/media/video/cx88/cx88-cards.c | 8 ++++++++ 3 files changed, 11 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/common/tuners/tuner-xc2028.c b/drivers/media/common/tuners/tuner-xc2028.c index aa20ce8cc668..f270e605da83 100644 --- a/drivers/media/common/tuners/tuner-xc2028.c +++ b/drivers/media/common/tuners/tuner-xc2028.c @@ -1119,8 +1119,8 @@ static int xc2028_sleep(struct dvb_frontend *fe) struct xc2028_data *priv = fe->tuner_priv; int rc = 0; - /* Avoid firmware reload on slow devices */ - if (no_poweroff) + /* Avoid firmware reload on slow devices or if PM disabled */ + if (no_poweroff || priv->ctrl.disable_power_mgmt) return 0; tuner_dbg("Putting xc2028/3028 into poweroff mode.\n"); diff --git a/drivers/media/common/tuners/tuner-xc2028.h b/drivers/media/common/tuners/tuner-xc2028.h index 19de7928a74e..a90c35d50add 100644 --- a/drivers/media/common/tuners/tuner-xc2028.h +++ b/drivers/media/common/tuners/tuner-xc2028.h @@ -38,6 +38,7 @@ struct xc2028_ctrl { unsigned int input1:1; unsigned int vhfbw7:1; unsigned int uhfbw8:1; + unsigned int disable_power_mgmt:1; unsigned int demod; enum firmware_type type:2; }; diff --git a/drivers/media/video/cx88/cx88-cards.c b/drivers/media/video/cx88/cx88-cards.c index a5cc1c1fc2d6..39465301ec94 100644 --- a/drivers/media/video/cx88/cx88-cards.c +++ b/drivers/media/video/cx88/cx88-cards.c @@ -3003,6 +3003,14 @@ void cx88_setup_xc3028(struct cx88_core *core, struct xc2028_ctrl *ctl) case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO: ctl->demod = XC3028_FE_OREN538; break; + case CX88_BOARD_GENIATECH_X8000_MT: + /* FIXME: For this board, the xc3028 never recovers after being + powered down (the reset GPIO probably is not set properly). + We don't have access to the hardware so we cannot determine + which GPIO is used for xc3028, so just disable power xc3028 + power management for now */ + ctl->disable_power_mgmt = 1; + break; case CX88_BOARD_WINFAST_TV2000_XP_GLOBAL: case CX88_BOARD_PROLINK_PV_GLOBAL_XTREME: case CX88_BOARD_PROLINK_PV_8000GT: -- cgit v1.2.3 From 83053f7fe3eb0b6b1634d24ede87f1daa01ae60c Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 6 Aug 2009 21:03:35 -0300 Subject: V4L/DVB (12399): mt9v011: Add support for controlling frame rates Implement g_parm/s_parm ioctls. Those are used to check the current frame rate (in fps) and to set it to a value. In practice, there are only 15 possible different speeds, due to chip limits. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 89 ++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 87 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index c14bf47d6928..8de1316a276d 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -156,7 +156,7 @@ static void set_balance(struct v4l2_subdev *sd) mt9v011_write(sd, R2D_MT9V011_RED_GAIN, red_gain); } -static void calc_fps(struct v4l2_subdev *sd) +static void calc_fps(struct v4l2_subdev *sd, u32 *numerator, u32 *denominator) { struct mt9v011 *core = to_mt9v011(sd); unsigned height, width, hblank, vblank, speed; @@ -179,6 +179,51 @@ static void calc_fps(struct v4l2_subdev *sd) v4l2_dbg(1, debug, sd, "Programmed to %u.%03u fps (%d pixel clcks)\n", tmp / 1000, tmp % 1000, t_time); + + if (numerator && denominator) { + *numerator = 1000; + *denominator = (u32)frames_per_ms; + } +} + +static u16 calc_speed(struct v4l2_subdev *sd, u32 numerator, u32 denominator) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned height, width, hblank, vblank; + unsigned row_time, line_time; + u64 t_time, speed; + + /* Avoid bogus calculus */ + if (!numerator || !denominator) + return 0; + + height = mt9v011_read(sd, R03_MT9V011_HEIGHT); + width = mt9v011_read(sd, R04_MT9V011_WIDTH); + hblank = mt9v011_read(sd, R05_MT9V011_HBLANK); + vblank = mt9v011_read(sd, R06_MT9V011_VBLANK); + + row_time = width + 113 + hblank; + line_time = height + vblank + 1; + + t_time = core->xtal * ((u64)numerator); + /* round to the closest value */ + t_time += denominator / 2; + do_div(t_time, denominator); + + speed = t_time; + do_div(speed, row_time * line_time); + + /* Avoid having a negative value for speed */ + if (speed < 2) + speed = 0; + else + speed -= 2; + + /* Avoid speed overflow */ + if (speed > 15) + return 15; + + return (u16)speed; } static void set_res(struct v4l2_subdev *sd) @@ -207,7 +252,7 @@ static void set_res(struct v4l2_subdev *sd) mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height); mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height); - calc_fps(sd); + calc_fps(sd, NULL, NULL); }; static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) @@ -322,6 +367,44 @@ static int mt9v011_try_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) return 0; } +static int mt9v011_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) +{ + struct v4l2_captureparm *cp = &parms->parm.capture; + + if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + memset(cp, 0, sizeof(struct v4l2_captureparm)); + cp->capability = V4L2_CAP_TIMEPERFRAME; + calc_fps(sd, + &cp->timeperframe.numerator, + &cp->timeperframe.denominator); + + return 0; +} + +static int mt9v011_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms) +{ + struct v4l2_captureparm *cp = &parms->parm.capture; + struct v4l2_fract *tpf = &cp->timeperframe; + u16 speed; + + if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + if (cp->extendedmode != 0) + return -EINVAL; + + speed = calc_speed(sd, tpf->numerator, tpf->denominator); + + mt9v011_write(sd, R0A_MT9V011_CLK_SPEED, speed); + v4l2_dbg(1, debug, sd, "Setting speed to %d\n", speed); + + /* Recalculate and update fps info */ + calc_fps(sd, &tpf->numerator, &tpf->denominator); + + return 0; +} + static int mt9v011_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) { struct v4l2_pix_format *pix = &fmt->fmt.pix; @@ -419,6 +502,8 @@ static const struct v4l2_subdev_video_ops mt9v011_video_ops = { .enum_fmt = mt9v011_enum_fmt, .try_fmt = mt9v011_try_fmt, .s_fmt = mt9v011_s_fmt, + .g_parm = mt9v011_g_parm, + .s_parm = mt9v011_s_parm, }; static const struct v4l2_subdev_ops mt9v011_ops = { -- cgit v1.2.3 From d96ecda63f41350dc93c17ccb72ea24511f207a9 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 6 Aug 2009 21:53:59 -0300 Subject: V4L/DVB (12400): em28xx: Allow changing fps on webcams em28xx doesn't have temporal scaling. However, on webcams, sensors are capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should be passed to the sensor for it to properly set frame rate. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-video.c | 37 +++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index ff37b4c15f44..92ee9c644328 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -846,6 +846,41 @@ static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id *norm) return 0; } +static int vidioc_g_parm(struct file *file, void *priv, + struct v4l2_streamparm *p) +{ + struct em28xx_fh *fh = priv; + struct em28xx *dev = fh->dev; + int rc = 0; + + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + if (dev->board.is_webcam) + rc = v4l2_device_call_until_err(&dev->v4l2_dev, 0, + video, g_parm, p); + else + v4l2_video_std_frame_period(dev->norm, + &p->parm.capture.timeperframe); + + return rc; +} + +static int vidioc_s_parm(struct file *file, void *priv, + struct v4l2_streamparm *p) +{ + struct em28xx_fh *fh = priv; + struct em28xx *dev = fh->dev; + + if (!dev->board.is_webcam) + return -EINVAL; + + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) + return -EINVAL; + + return v4l2_device_call_until_err(&dev->v4l2_dev, 0, video, s_parm, p); +} + static const char *iname[] = { [EM28XX_VMUX_COMPOSITE1] = "Composite1", [EM28XX_VMUX_COMPOSITE2] = "Composite2", @@ -1885,6 +1920,8 @@ static const struct v4l2_ioctl_ops video_ioctl_ops = { .vidioc_qbuf = vidioc_qbuf, .vidioc_dqbuf = vidioc_dqbuf, .vidioc_s_std = vidioc_s_std, + .vidioc_g_parm = vidioc_g_parm, + .vidioc_s_parm = vidioc_s_parm, .vidioc_enum_input = vidioc_enum_input, .vidioc_g_input = vidioc_g_input, .vidioc_s_input = vidioc_s_input, -- cgit v1.2.3 From 2526ea6e46e41322eb98ac0e9c616273402bd661 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 01:09:54 -0300 Subject: V4L/DVB (12401): m9v011: add vflip/hflip controls to control mirror/upside down Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mt9v011.c | 53 +++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 51 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c index 8de1316a276d..cc85f77a5706 100644 --- a/drivers/media/video/mt9v011.c +++ b/drivers/media/video/mt9v011.c @@ -52,13 +52,34 @@ static struct v4l2_queryctrl mt9v011_qctrl[] = { .step = 1, .default_value = 0, .flags = 0, - }, + }, { + .id = V4L2_CID_HFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Mirror", + .minimum = 0, + .maximum = 1, + .step = 1, + .default_value = 0, + .flags = 0, + }, { + .id = V4L2_CID_VFLIP, + .type = V4L2_CTRL_TYPE_BOOLEAN, + .name = "Vflip", + .minimum = 0, + .maximum = 1, + .step = 1, + .default_value = 0, + .flags = 0, + }, { + } }; struct mt9v011 { struct v4l2_subdev sd; unsigned width, height; unsigned xtal; + unsigned hflip:1; + unsigned vflip:1; u16 global_gain, red_bal, blue_bal; }; @@ -131,7 +152,6 @@ static const struct i2c_reg_value mt9v011_init_default[] = { { R0A_MT9V011_CLK_SPEED, 0x0000 }, { R1E_MT9V011_DIGITAL_ZOOM, 0x0000 }, - { R20_MT9V011_READ_MODE, 0x1000 }, { R07_MT9V011_OUT_CTRL, 0x0002 }, /* chip enable */ }; @@ -255,6 +275,20 @@ static void set_res(struct v4l2_subdev *sd) calc_fps(sd, NULL, NULL); }; +static void set_read_mode(struct v4l2_subdev *sd) +{ + struct mt9v011 *core = to_mt9v011(sd); + unsigned mode = 0x1000; + + if (core->hflip) + mode |= 0x4000; + + if (core->vflip) + mode |= 0x8000; + + mt9v011_write(sd, R20_MT9V011_READ_MODE, mode); +} + static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) { int i; @@ -265,6 +299,7 @@ static int mt9v011_reset(struct v4l2_subdev *sd, u32 val) set_balance(sd); set_res(sd); + set_read_mode(sd); return 0; }; @@ -285,6 +320,12 @@ static int mt9v011_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) case V4L2_CID_BLUE_BALANCE: ctrl->value = core->blue_bal; return 0; + case V4L2_CID_HFLIP: + ctrl->value = core->hflip ? 1 : 0; + return 0; + case V4L2_CID_VFLIP: + ctrl->value = core->vflip ? 1 : 0; + return 0; } return -EINVAL; } @@ -333,6 +374,14 @@ static int mt9v011_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl) case V4L2_CID_BLUE_BALANCE: core->blue_bal = ctrl->value; break; + case V4L2_CID_HFLIP: + core->hflip = ctrl->value; + set_read_mode(sd); + return 0; + case V4L2_CID_VFLIP: + core->vflip = ctrl->value; + set_read_mode(sd); + return 0; default: return -EINVAL; } -- cgit v1.2.3 From 9b4e845c6cbca2bcbfdb87e4d005260604226f45 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 12:08:02 -0300 Subject: V4L/DVB (12402): em28xx: fix: some em2710 chips use a different vendor ID Thanks to hermann pitton for pointing this new variation. Tested-by: hermann pitton Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/CARDLIST.em28xx | 2 +- drivers/media/video/em28xx/em28xx-cards.c | 2 ++ 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx index 68c236c01846..e352d754875c 100644 --- a/Documentation/video4linux/CARDLIST.em28xx +++ b/Documentation/video4linux/CARDLIST.em28xx @@ -1,5 +1,5 @@ 0 -> Unknown EM2800 video grabber (em2800) [eb1a:2800] - 1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883] + 1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2710,eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883] 2 -> Terratec Cinergy 250 USB (em2820/em2840) [0ccd:0036] 3 -> Pinnacle PCTV USB 2 (em2820/em2840) [2304:0208] 4 -> Hauppauge WinTV USB 2 (em2820/em2840) [2040:4200,2040:4201] diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index d0b033bce867..6c35d789cd7e 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1549,6 +1549,8 @@ struct usb_device_id em28xx_id_table[] = { .driver_info = EM2750_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2800), .driver_info = EM2800_BOARD_UNKNOWN }, + { USB_DEVICE(0xeb1a, 0x2710), + .driver_info = EM2820_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2820), .driver_info = EM2820_BOARD_UNKNOWN }, { USB_DEVICE(0xeb1a, 0x2821), -- cgit v1.2.3 From d594317bdc716ccd8c8cf711e3827f9b6e0b766b Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 12:13:31 -0300 Subject: V4L/DVB (12403): em28xx: properly reports some em2710 chips As reported by hermann pitton , some devices has a different chip id for em2710 (likely the older ones): em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0) em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22) em28xx #0: em28xx chip ID = 17 Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 5 ++++- drivers/media/video/em28xx/em28xx-reg.h | 3 ++- 2 files changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 6c35d789cd7e..c9e420e8a614 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1840,11 +1840,14 @@ void em28xx_pre_card_setup(struct em28xx *dev) dev->chip_id = rc; switch (dev->chip_id) { + case CHIP_ID_EM2710: + em28xx_info("chip ID is em2710\n"); + break; case CHIP_ID_EM2750: em28xx_info("chip ID is em2750\n"); break; case CHIP_ID_EM2820: - em28xx_info("chip ID is em2710 or em2820\n"); + em28xx_info("chip ID is em2820 (or em2710)\n"); break; case CHIP_ID_EM2840: em28xx_info("chip ID is em2840\n"); diff --git a/drivers/media/video/em28xx/em28xx-reg.h b/drivers/media/video/em28xx/em28xx-reg.h index a2676d63cfd0..6bf84bd787df 100644 --- a/drivers/media/video/em28xx/em28xx-reg.h +++ b/drivers/media/video/em28xx/em28xx-reg.h @@ -176,7 +176,8 @@ /* FIXME: Need to be populated with the other chip ID's */ enum em28xx_chip_id { - CHIP_ID_EM2820 = 18, /* Also used by em2710 */ + CHIP_ID_EM2710 = 17, + CHIP_ID_EM2820 = 18, /* Also used by some em2710 */ CHIP_ID_EM2840 = 20, CHIP_ID_EM2750 = 33, CHIP_ID_EM2860 = 34, -- cgit v1.2.3 From c2a6b54a9cf08d4ffeb75d70603c4a5d03ac97ad Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 8 Aug 2009 03:14:55 -0300 Subject: V4L/DVB (12406): em28xx: fix: don't do image interlacing on webcams Due to historical reasons, em28xx driver gets two consecutive frames and fold them into an unique framing, doing interlacing. While this works fine for TV images, this produces two bad effects with webcams: 1) webcam images are progressive. Merging two consecutive images produce interlacing artifacts on the image; 2) since the driver needs to get two frames, it reduces the maximum frame rate by two. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ++++ drivers/media/video/em28xx/em28xx-core.c | 5 +++- drivers/media/video/em28xx/em28xx-video.c | 40 ++++++++++++++++++++++++------- drivers/media/video/em28xx/em28xx.h | 3 +++ 4 files changed, 42 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index c9e420e8a614..9011a498e5b3 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2502,6 +2502,10 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, if (em28xx_hint_sensor(dev) < 0) dev->board.is_webcam = 0; + /* It makes no sense to use de-interlacing mode on webcams */ + if (dev->board.is_webcam) + dev->progressive = 1; + /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 5b78e199abd1..339fffdf6bce 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -720,7 +720,10 @@ int em28xx_resolution_set(struct em28xx *dev) { int width, height; width = norm_maxw(dev); - height = norm_maxh(dev) >> 1; + height = norm_maxh(dev); + + if (!dev->progressive) + height >>= norm_maxh(dev); em28xx_set_outfmt(dev); diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index 92ee9c644328..ab079d9256c4 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -194,15 +194,24 @@ static void em28xx_copy_video(struct em28xx *dev, startread = p; remain = len; - /* Interlaces frame */ - if (buf->top_field) + if (dev->progressive) fieldstart = outp; - else - fieldstart = outp + bytesperline; + else { + /* Interlaces two half frames */ + if (buf->top_field) + fieldstart = outp; + else + fieldstart = outp + bytesperline; + } linesdone = dma_q->pos / bytesperline; currlinedone = dma_q->pos % bytesperline; - offset = linesdone * bytesperline * 2 + currlinedone; + + if (dev->progressive) + offset = linesdone * bytesperline + currlinedone; + else + offset = linesdone * bytesperline * 2 + currlinedone; + startwrite = fieldstart + offset; lencopy = bytesperline - currlinedone; lencopy = lencopy > remain ? remain : lencopy; @@ -376,7 +385,7 @@ static inline int em28xx_isoc_copy(struct em28xx *dev, struct urb *urb) em28xx_isocdbg("Video frame %d, length=%i, %s\n", p[2], len, (p[2] & 1) ? "odd" : "even"); - if (!(p[2] & 1)) { + if (dev->progressive || !(p[2] & 1)) { if (buf != NULL) buffer_filled(dev, dma_q, buf); get_next_buf(dma_q, &buf); @@ -689,7 +698,10 @@ static int vidioc_g_fmt_vid_cap(struct file *file, void *priv, f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; /* FIXME: TOP? NONE? BOTTOM? ALTENATE? */ - f->fmt.pix.field = dev->interlaced ? + if (dev->progressive) + f->fmt.pix.field = V4L2_FIELD_NONE; + else + f->fmt.pix.field = dev->interlaced ? V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP; mutex_unlock(&dev->lock); @@ -753,7 +765,11 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, f->fmt.pix.bytesperline = (dev->width * fmt->depth + 7) >> 3; f->fmt.pix.sizeimage = f->fmt.pix.bytesperline * height; f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; - f->fmt.pix.field = V4L2_FIELD_INTERLACED; + if (dev->progressive) + f->fmt.pix.field = V4L2_FIELD_NONE; + else + f->fmt.pix.field = dev->interlaced ? + V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP; return 0; } @@ -1659,6 +1675,7 @@ static int em28xx_v4l2_open(struct file *filp) struct em28xx *dev; enum v4l2_buf_type fh_type; struct em28xx_fh *fh; + enum v4l2_field field; dev = em28xx_get_device(minor, &fh_type, &radio); @@ -1700,8 +1717,13 @@ static int em28xx_v4l2_open(struct file *filp) dev->users++; + if (dev->progressive) + field = V4L2_FIELD_NONE; + else + field = V4L2_FIELD_INTERLACED; + videobuf_queue_vmalloc_init(&fh->vb_vidq, &em28xx_video_qops, - NULL, &dev->slock, fh->type, V4L2_FIELD_INTERLACED, + NULL, &dev->slock, fh->type, field, sizeof(struct em28xx_buffer), fh); mutex_unlock(&dev->lock); diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h index 45bd513f62dc..8c2dc38bca9f 100644 --- a/drivers/media/video/em28xx/em28xx.h +++ b/drivers/media/video/em28xx/em28xx.h @@ -484,6 +484,9 @@ struct em28xx { int sensor_xres, sensor_yres; int sensor_xtal; + /* Allows progressive (e. g. non-interlaced) mode */ + int progressive; + /* Vinmode/Vinctl used at the driver */ int vinmode, vinctl; -- cgit v1.2.3 From 970cff36c0850e8193ac1162e42c7c11001b872d Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 8 Aug 2009 03:28:41 -0300 Subject: V4L/DVB (12407): em28xx: Adjust Silvercrest xtal frequency We don't know the xtal frequency of Silvercrest, but we need to have some value in order to allow controlling the frame rate frequency. The value is probably still wrong, since the manufacturer announces this device as being capable of 30fps, but the maximum we can get is 13.5 fps. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 9011a498e5b3..fc46032bfe27 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1785,7 +1785,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; - dev->sensor_xtal = 6300000; + dev->sensor_xtal = 12150000; /* probably means GRGB 16 bit bayer */ dev->vinmode = 0x0d; -- cgit v1.2.3 From fcd20e3c369caf7a3fec300c9c183b25a06e21b2 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 10 Aug 2009 02:57:57 -0300 Subject: V4L/DVB (12410): em28xx: Move the non-board dependent part to be outside em28xx_pre_card_setup() em28xx_pre_card_setup() is meant to contain board-specific initialization. Also, as autodetection sometimes occur only after having i2c bus enabled, this function may need to be called later. Moving those setups to happen outside the function avoids calling it twice without need and without duplicating output lines at dmesg. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 111 ++++++++++++++---------------- 1 file changed, 53 insertions(+), 58 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index fc46032bfe27..6b2b5d3e2fad 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -1821,63 +1821,6 @@ static int em28xx_hint_sensor(struct em28xx *dev) */ void em28xx_pre_card_setup(struct em28xx *dev) { - int rc; - - em28xx_set_model(dev); - - em28xx_info("Identified as %s (card=%d)\n", - dev->board.name, dev->model); - - /* Set the default GPO/GPIO for legacy devices */ - dev->reg_gpo_num = EM2880_R04_GPO; - dev->reg_gpio_num = EM28XX_R08_GPIO; - - dev->wait_after_write = 5; - - /* Based on the Chip ID, set the device configuration */ - rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID); - if (rc > 0) { - dev->chip_id = rc; - - switch (dev->chip_id) { - case CHIP_ID_EM2710: - em28xx_info("chip ID is em2710\n"); - break; - case CHIP_ID_EM2750: - em28xx_info("chip ID is em2750\n"); - break; - case CHIP_ID_EM2820: - em28xx_info("chip ID is em2820 (or em2710)\n"); - break; - case CHIP_ID_EM2840: - em28xx_info("chip ID is em2840\n"); - break; - case CHIP_ID_EM2860: - em28xx_info("chip ID is em2860\n"); - break; - case CHIP_ID_EM2870: - em28xx_info("chip ID is em2870\n"); - dev->wait_after_write = 0; - break; - case CHIP_ID_EM2874: - em28xx_info("chip ID is em2874\n"); - dev->reg_gpio_num = EM2874_R80_GPIO; - dev->wait_after_write = 0; - break; - case CHIP_ID_EM2883: - em28xx_info("chip ID is em2882/em2883\n"); - dev->wait_after_write = 0; - break; - default: - em28xx_info("em28xx chip ID = %d\n", dev->chip_id); - } - } - - /* Prepopulate cached GPO register content */ - rc = em28xx_read_reg(dev, dev->reg_gpo_num); - if (rc >= 0) - dev->reg_gpo = rc; - /* Set the initial XCLK and I2C clock values based on the board definition */ em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f); @@ -2443,7 +2386,7 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, int minor) { struct em28xx *dev = *devhandle; - int retval = -ENOMEM; + int retval; int errCode; dev->udev = udev; @@ -2460,6 +2403,58 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, dev->em28xx_read_reg_req = em28xx_read_reg_req; dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800; + em28xx_set_model(dev); + + /* Set the default GPO/GPIO for legacy devices */ + dev->reg_gpo_num = EM2880_R04_GPO; + dev->reg_gpio_num = EM28XX_R08_GPIO; + + dev->wait_after_write = 5; + + /* Based on the Chip ID, set the device configuration */ + retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID); + if (retval > 0) { + dev->chip_id = retval; + + switch (dev->chip_id) { + case CHIP_ID_EM2710: + em28xx_info("chip ID is em2710\n"); + break; + case CHIP_ID_EM2750: + em28xx_info("chip ID is em2750\n"); + break; + case CHIP_ID_EM2820: + em28xx_info("chip ID is em2820 (or em2710)\n"); + break; + case CHIP_ID_EM2840: + em28xx_info("chip ID is em2840\n"); + break; + case CHIP_ID_EM2860: + em28xx_info("chip ID is em2860\n"); + break; + case CHIP_ID_EM2870: + em28xx_info("chip ID is em2870\n"); + dev->wait_after_write = 0; + break; + case CHIP_ID_EM2874: + em28xx_info("chip ID is em2874\n"); + dev->reg_gpio_num = EM2874_R80_GPIO; + dev->wait_after_write = 0; + break; + case CHIP_ID_EM2883: + em28xx_info("chip ID is em2882/em2883\n"); + dev->wait_after_write = 0; + break; + default: + em28xx_info("em28xx chip ID = %d\n", dev->chip_id); + } + } + + /* Prepopulate cached GPO register content */ + retval = em28xx_read_reg(dev, dev->reg_gpo_num); + if (retval >= 0) + dev->reg_gpo = retval; + em28xx_pre_card_setup(dev); if (!dev->board.is_em2800) { -- cgit v1.2.3 From 3d3215c4e4cfca74e5805a8506d50a6752172e81 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Mon, 10 Aug 2009 10:29:27 -0300 Subject: V4L/DVB (12411): em28xx: Fix artifacts with Silvercrest webcam Silvercrest mt9v011 sensor produces a 640x480 image. However, previously, the code were getting only half of the lines and merging two consecutive frames to "produce" a 640x480 image. With the addition of progressive mode, now em28xx is working with a full image. However, when the number of lines is bigger than 240, the beginning of some odd lines are filled with blank. After lots of testing, and physically checking the device for a Xtal, it was noticed experimentally that mt9v011 is using em28xx XCLK as its clock. Due to that, changing XCLK value changes the maximum speed of the stream. At the tests, it were possible to produce up to 32 fps, using a 30 MHz XCLK. However, at that rate, the artifacts happen even at 320x240. Lower values of XCLK produces artifacts only at 640x480. At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is possible to see an invalid sucession of artifacts with this pattern: .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx (where the dots represent the blanked pixels) So, it seems that a waveform in the format of a ramp is interferring at the image. The cause of this interference is currently unknown. Some possibilities are: - electrical interference (maybe this device is broken?); - some issue at mt9v011 programming; - some bug at em28xx chip. So, for now, let's be conservative and use a value of XCLK that we know for sure that it won't cause artifacts. As I'm waiting for more of such devices with different em28xx chipset revisions, I'll have the opportunity to double check the issue with other pieces of hardware. Later patches can vary XCLK depending on the vertical resolutions, if a proper fix is not discovered. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 50 +++++++++++++++++++++---------- 1 file changed, 34 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 6b2b5d3e2fad..54429b629b2d 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -218,7 +218,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = { struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { .name = "EM2710/EM2750/EM2751 webcam grabber", - .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, + .xclk = EM28XX_XCLK_FREQUENCY_20MHZ, .tuner_type = TUNER_ABSENT, .is_webcam = 1, .input = { { @@ -1768,6 +1768,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; + /* Micron sensor detection */ dev->i2c_client.addr = 0xba >> 1; cmd = 0; i2c_master_send(&dev->i2c_client, &cmd, 1); @@ -1776,16 +1777,27 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; version = be16_to_cpu(version_be); - switch (version) { case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */ case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; + em28xx_set_model(dev); + sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; - dev->sensor_xtal = 12150000; + /* + * FIXME: mt9v011 uses I2S speed as xtal clk - at least with + * the Silvercrest cam I have here for testing - for higher + * resolutions, a high clock cause horizontal artifacts, so we + * need to use a lower xclk frequency. + * Yet, it would be possible to adjust xclk depending on the + * desired resolution, since this affects directly the + * frame rate. + */ + dev->board.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ; + dev->sensor_xtal = 4300000; /* probably means GRGB 16 bit bayer */ dev->vinmode = 0x0d; @@ -1794,6 +1806,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) break; case 0x8431: dev->model = EM2750_BOARD_UNKNOWN; + em28xx_set_model(dev); + sensor_name = "mt9m001"; dev->em28xx_sensor = EM28XX_MT9M001; em28xx_initialize_mt9m001(dev); @@ -1810,6 +1824,9 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; } + /* Setup webcam defaults */ + em28xx_pre_card_setup(dev); + em28xx_errdev("Sensor is %s, using model %s entry.\n", sensor_name, em28xx_boards[dev->model].name); @@ -2169,7 +2186,20 @@ void em28xx_register_i2c_ir(struct em28xx *dev) void em28xx_card_setup(struct em28xx *dev) { - em28xx_set_model(dev); + /* + * If the device can be a webcam, seek for a sensor. + * If sensor is not found, then it isn't a webcam. + */ + if (dev->board.is_webcam) { + if (em28xx_hint_sensor(dev) < 0) + dev->board.is_webcam = 0; + else + dev->progressive = 1; + } else + em28xx_set_model(dev); + + em28xx_info("Identified as %s (card=%d)\n", + dev->board.name, dev->model); dev->tuner_type = em28xx_boards[dev->model].tuner_type; if (em28xx_boards[dev->model].tuner_addr) @@ -2489,18 +2519,6 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, dev->vinmode = 0x10; dev->vinctl = 0x11; - /* - * If the device can be a webcam, seek for a sensor. - * If sensor is not found, then it isn't a webcam. - */ - if (dev->board.is_webcam) - if (em28xx_hint_sensor(dev) < 0) - dev->board.is_webcam = 0; - - /* It makes no sense to use de-interlacing mode on webcams */ - if (dev->board.is_webcam) - dev->progressive = 1; - /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); -- cgit v1.2.3 From d7612c86d099939503c2f849a523dbca753d1935 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 7 Aug 2009 18:43:00 -0300 Subject: V4L/DVB (12405): em28xx-cards: move register 0x13 setting to the proper place Register 0x13 seems to be a sort of image control, maybe gamma, white level or black level. Lower values produce better images, while higher values increases the contrast and shifts colors to green. 0xff produces a black image. This register is not Silvercrest-specific, so its code should be moved to a better place. If this register is left alone, a random value can be found at the register, producing weird results. While here, let's remove register 0x0d, as it had no noticed effect at the image. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-cards.c | 4 ---- drivers/media/video/em28xx/em28xx-core.c | 3 +++ 2 files changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 54429b629b2d..ed281f565945 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -2273,10 +2273,6 @@ void em28xx_card_setup(struct em28xx *dev) em28xx_gpio_set(dev, dev->board.tuner_gpio); em28xx_set_mode(dev, EM28XX_ANALOG_MODE); break; - case EM2820_BOARD_SILVERCREST_WEBCAM: - /* FIXME: need to document the registers bellow */ - em28xx_write_reg(dev, 0x0d, 0x42); - em28xx_write_reg(dev, 0x13, 0x08); } if (dev->board.has_snapshot_button) diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index 339fffdf6bce..98e140b5d95e 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -632,6 +632,9 @@ int em28xx_capture_start(struct em28xx *dev, int start) return rc; } + if (dev->board.is_webcam) + rc = em28xx_write_reg(dev, 0x13, 0x0c); + /* enable video capture */ rc = em28xx_write_reg(dev, 0x48, 0x00); -- cgit v1.2.3 From 7d2e2e35fb50f381c9398e481aac1e1729765ae3 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Wed, 5 Aug 2009 12:58:47 -0300 Subject: V4L/DVB (12422): media/zr364xx: fix build errors Fix build errors in zr364xx by adding selects: zr364xx.c:(.text+0x195ed7): undefined reference to `videobuf_streamon' zr364xx.c:(.text+0x196030): undefined reference to `videobuf_dqbuf' zr364xx.c:(.text+0x1960c4): undefined reference to `videobuf_qbuf' zr364xx.c:(.text+0x196123): undefined reference to `videobuf_querybuf' zr364xx.c:(.text+0x196182): undefined reference to `videobuf_reqbufs' zr364xx.c:(.text+0x196224): undefined reference to `videobuf_queue_is_busy' zr364xx.c:(.text+0x196390): undefined reference to `videobuf_vmalloc_free' zr364xx.c:(.text+0x196571): undefined reference to `videobuf_iolock' zr364xx.c:(.text+0x196678): undefined reference to `videobuf_mmap_mapper' zr364xx.c:(.text+0x196760): undefined reference to `videobuf_poll_stream' zr364xx.c:(.text+0x19689a): undefined reference to `videobuf_read_one' zr364xx.c:(.text+0x1969ec): undefined reference to `videobuf_mmap_free' zr364xx.c:(.text+0x197862): undefined reference to `videobuf_queue_vmalloc_init' zr364xx.c:(.text+0x197a28): undefined reference to `videobuf_streamoff' zr364xx.c:(.text+0x198203): undefined reference to `videobuf_to_vmalloc' zr364xx.c:(.text+0x198603): undefined reference to `videobuf_streamoff' drivers/built-in.o: In function `free_buffer': zr364xx.c:(.text+0x19930c): undefined reference to `videobuf_vmalloc_free' drivers/built-in.o: In function `zr364xx_open': zr364xx.c:(.text+0x19a7de): undefined reference to `videobuf_queue_vmalloc_init' drivers/built-in.o: In function `read_pipe_completion': zr364xx.c:(.text+0x19b17f): undefined reference to `videobuf_to_vmalloc' Signed-off-by: Randy Dunlap Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/Kconfig | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig index 84b6fc15519d..dcf9fa9264bb 100644 --- a/drivers/media/video/Kconfig +++ b/drivers/media/video/Kconfig @@ -920,6 +920,8 @@ source "drivers/media/video/pwc/Kconfig" config USB_ZR364XX tristate "USB ZR364XX Camera support" depends on VIDEO_V4L2 + select VIDEOBUF_GEN + select VIDEOBUF_VMALLOC ---help--- Say Y here if you want to connect this type of camera to your computer's USB port. -- cgit v1.2.3 From 2dd54a54c19d0e5b50f4e1c591653772ead9d4a1 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Wed, 5 Aug 2009 20:06:31 -0300 Subject: V4L/DVB (12424): soc-camera: fix recursive locking in .buf_queue() The .buf_queue() V4L2 driver method is called under spinlock_irqsave(q->irqlock,...), don't take the lock again inside the function. Reported-by: Antonio Ospite Signed-off-by: Guennadi Liakhovetski Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/mx1_camera.c | 6 +----- drivers/media/video/mx3_camera.c | 19 ++++++++++--------- drivers/media/video/pxa_camera.c | 6 +----- drivers/media/video/sh_mobile_ceu_camera.c | 5 +---- 4 files changed, 13 insertions(+), 23 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/mx1_camera.c b/drivers/media/video/mx1_camera.c index 2d075205bdfe..736c31d23194 100644 --- a/drivers/media/video/mx1_camera.c +++ b/drivers/media/video/mx1_camera.c @@ -234,6 +234,7 @@ static int mx1_camera_setup_dma(struct mx1_camera_dev *pcdev) return ret; } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void mx1_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -241,13 +242,10 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq, struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct mx1_camera_dev *pcdev = ici->priv; struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb); - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, vb, vb->baddr, vb->bsize); - spin_lock_irqsave(&pcdev->lock, flags); - list_add_tail(&vb->queue, &pcdev->capture); vb->state = VIDEOBUF_ACTIVE; @@ -264,8 +262,6 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq, __raw_writel(temp, pcdev->base + CSICR1); } } - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void mx1_videobuf_release(struct videobuf_queue *vq, diff --git a/drivers/media/video/mx3_camera.c b/drivers/media/video/mx3_camera.c index e605c076ed89..9770cb7932ca 100644 --- a/drivers/media/video/mx3_camera.c +++ b/drivers/media/video/mx3_camera.c @@ -332,7 +332,10 @@ static enum pixel_fmt fourcc_to_ipu_pix(__u32 fourcc) } } -/* Called with .vb_lock held */ +/* + * Called with .vb_lock mutex held and + * under spinlock_irqsave(&mx3_cam->lock, ...) + */ static void mx3_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -346,7 +349,8 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, struct idmac_video_param *video = &ichan->params.video; const struct soc_camera_data_format *data_fmt = icd->current_fmt; dma_cookie_t cookie; - unsigned long flags; + + BUG_ON(!irqs_disabled()); /* This is the configuration of one sg-element */ video->out_pixel_fmt = fourcc_to_ipu_pix(data_fmt->fourcc); @@ -359,8 +363,6 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, memset((void *)vb->baddr, 0xaa, vb->bsize); #endif - spin_lock_irqsave(&mx3_cam->lock, flags); - list_add_tail(&vb->queue, &mx3_cam->capture); if (!mx3_cam->active) { @@ -370,24 +372,23 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq, vb->state = VIDEOBUF_QUEUED; } - spin_unlock_irqrestore(&mx3_cam->lock, flags); + spin_unlock_irq(&mx3_cam->lock); cookie = txd->tx_submit(txd); dev_dbg(&icd->dev, "Submitted cookie %d DMA 0x%08x\n", cookie, sg_dma_address(&buf->sg)); + + spin_lock_irq(&mx3_cam->lock); + if (cookie >= 0) return; /* Submit error */ vb->state = VIDEOBUF_PREPARED; - spin_lock_irqsave(&mx3_cam->lock, flags); - list_del_init(&vb->queue); if (mx3_cam->active == buf) mx3_cam->active = NULL; - - spin_unlock_irqrestore(&mx3_cam->lock, flags); } /* Called with .vb_lock held */ diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c index e048d25798cc..016bb45ba0c3 100644 --- a/drivers/media/video/pxa_camera.c +++ b/drivers/media/video/pxa_camera.c @@ -612,6 +612,7 @@ static void pxa_camera_stop_capture(struct pxa_camera_dev *pcdev) dev_dbg(pcdev->soc_host.dev, "%s\n", __func__); } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void pxa_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { @@ -619,13 +620,10 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq, struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct pxa_camera_dev *pcdev = ici->priv; struct pxa_buffer *buf = container_of(vb, struct pxa_buffer, vb); - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d active=%p\n", __func__, vb, vb->baddr, vb->bsize, pcdev->active); - spin_lock_irqsave(&pcdev->lock, flags); - list_add_tail(&vb->queue, &pcdev->capture); vb->state = VIDEOBUF_ACTIVE; @@ -633,8 +631,6 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq, if (!pcdev->active) pxa_camera_start_capture(pcdev); - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void pxa_videobuf_release(struct videobuf_queue *vq, diff --git a/drivers/media/video/sh_mobile_ceu_camera.c b/drivers/media/video/sh_mobile_ceu_camera.c index 0db88a53d92c..e86878deea71 100644 --- a/drivers/media/video/sh_mobile_ceu_camera.c +++ b/drivers/media/video/sh_mobile_ceu_camera.c @@ -282,27 +282,24 @@ out: return ret; } +/* Called under spinlock_irqsave(&pcdev->lock, ...) */ static void sh_mobile_ceu_videobuf_queue(struct videobuf_queue *vq, struct videobuf_buffer *vb) { struct soc_camera_device *icd = vq->priv_data; struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); struct sh_mobile_ceu_dev *pcdev = ici->priv; - unsigned long flags; dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %zd\n", __func__, vb, vb->baddr, vb->bsize); vb->state = VIDEOBUF_QUEUED; - spin_lock_irqsave(&pcdev->lock, flags); list_add_tail(&vb->queue, &pcdev->capture); if (!pcdev->active) { pcdev->active = vb; sh_mobile_ceu_capture(pcdev); } - - spin_unlock_irqrestore(&pcdev->lock, flags); } static void sh_mobile_ceu_videobuf_release(struct videobuf_queue *vq, -- cgit v1.2.3 From 99362e1ece9f9651af1b849a01d91b9df1e0db2c Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Fri, 7 Aug 2009 07:10:52 -0300 Subject: V4L/DVB (12428): hdpvr: add missing initialization of current_norm Drivers should either set current_norm or supply a g_std callback. The hdpvr driver does neither. Since it initializes to a 60 Hz format I've initialized the current_norm to NTSC | PAL_M | PAL_60 which is the 60 Hz subset of tvnorms. Cc: Janne Grunau Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/hdpvr/hdpvr-video.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/media/video/hdpvr/hdpvr-video.c b/drivers/media/video/hdpvr/hdpvr-video.c index ccd47f57f42c..d678765cbba2 100644 --- a/drivers/media/video/hdpvr/hdpvr-video.c +++ b/drivers/media/video/hdpvr/hdpvr-video.c @@ -1220,6 +1220,8 @@ static const struct video_device hdpvr_video_template = { V4L2_STD_PAL_G | V4L2_STD_PAL_H | V4L2_STD_PAL_I | V4L2_STD_PAL_D | V4L2_STD_PAL_M | V4L2_STD_PAL_N | V4L2_STD_PAL_60, + .current_norm = V4L2_STD_NTSC | V4L2_STD_PAL_M | + V4L2_STD_PAL_60, }; int hdpvr_register_videodev(struct hdpvr_device *dev, struct device *parent, -- cgit v1.2.3 From 9bedc7f7fe803c17d26b5fcf5786b50a7cf40def Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Fri, 7 Aug 2009 07:28:16 -0300 Subject: V4L/DVB (12429): v4l2-ioctl: fix G_STD and G_PARM default handlers The v4l core supplies default handlers for G_STD and G_PARM. However, both default handlers are buggy. This patch fixes the following: 1) If no g_std is supplied and current_norm == 0, then this driver does not support TV video standards (e.g. a radio or webcam driver). Return -EINVAL. This ensures that there is no bogus VIDIOC_G_STD support for such drivers. 2) The default VIDIOC_G_PARM handler used current_norm instead of first checking if the driver supported g_std and calling that to get the norm. It also didn't check if current_norm was 0, since in that case the driver does not support TV standards (or no standard was set at all) and the default handler should return -EINVAL. Note that I am very unhappy with these default handlers: I think they basically behave like some very strange and unexpected side-effect. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/v4l2-ioctl.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/v4l2-ioctl.c b/drivers/media/video/v4l2-ioctl.c index be64a502ea27..f2afc4e08379 100644 --- a/drivers/media/video/v4l2-ioctl.c +++ b/drivers/media/video/v4l2-ioctl.c @@ -1081,8 +1081,10 @@ static long __video_do_ioctl(struct file *file, /* Calls the specific handler */ if (ops->vidioc_g_std) ret = ops->vidioc_g_std(file, fh, id); - else + else if (vfd->current_norm) *id = vfd->current_norm; + else + ret = -EINVAL; if (!ret) dbgarg(cmd, "std=0x%08Lx\n", (long long unsigned)*id); @@ -1553,12 +1555,19 @@ static long __video_do_ioctl(struct file *file, break; ret = ops->vidioc_g_parm(file, fh, p); } else { + v4l2_std_id std = vfd->current_norm; + if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) return -EINVAL; - v4l2_video_std_frame_period(vfd->current_norm, - &p->parm.capture.timeperframe); ret = 0; + if (ops->vidioc_g_std) + ret = ops->vidioc_g_std(file, fh, &std); + else if (std == 0) + ret = -EINVAL; + if (ret == 0) + v4l2_video_std_frame_period(std, + &p->parm.capture.timeperframe); } dbgarg(cmd, "type=%d\n", p->type); -- cgit v1.2.3 From 01a5fd6ff3fbae9a599d3334a8cca0f00865e360 Mon Sep 17 00:00:00 2001 From: Devin Heitmueller Date: Fri, 7 Aug 2009 09:25:06 -0300 Subject: V4L/DVB (12432): em28xx: fix regression in Empire DualTV digital tuning Restore support for digital tuning caused by regression during introduction of disable_i2c_gate parameter to zl10353 driver. Thanks to user "Xwang" for reporting the problem and testing the fix Cc: Xwang Signed-off-by: Devin Heitmueller Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/em28xx/em28xx-dvb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c index cf0ac7f2a30d..d603575431b4 100644 --- a/drivers/media/video/em28xx/em28xx-dvb.c +++ b/drivers/media/video/em28xx/em28xx-dvb.c @@ -478,7 +478,6 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_KWORLD_DVB_310U: - case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_zl10353_with_xc3028, &dev->i2c_adap); @@ -488,6 +487,7 @@ static int dvb_init(struct em28xx *dev) } break; case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900: + case EM2880_BOARD_EMPIRE_DUAL_TV: dvb->frontend = dvb_attach(zl10353_attach, &em28xx_zl10353_xc3028_no_i2c_gate, &dev->i2c_adap); -- cgit v1.2.3 From 77f2c2db1146154fb054e9ce955928a66d8c959f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:17:25 -0300 Subject: V4L/DVB (12436): stk-webcam: read buffer overflow It tested the value of stk_sizes[i].m before checking whether i was in range. Cc: Hans Verkuil Cc: Trent Piepho Signed-off-by: Roel Kluin Signed-off-by: Andrew Morton Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/stk-webcam.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/media/video/stk-webcam.c b/drivers/media/video/stk-webcam.c index 4d6785e63455..b154bd961e3b 100644 --- a/drivers/media/video/stk-webcam.c +++ b/drivers/media/video/stk-webcam.c @@ -1050,8 +1050,8 @@ static int stk_setup_format(struct stk_camera *dev) depth = 1; else depth = 2; - while (stk_sizes[i].m != dev->vsettings.mode - && i < ARRAY_SIZE(stk_sizes)) + while (i < ARRAY_SIZE(stk_sizes) && + stk_sizes[i].m != dev->vsettings.mode) i++; if (i == ARRAY_SIZE(stk_sizes)) { STK_ERROR("Something is broken in %s\n", __func__); -- cgit v1.2.3 From 27059b35397fc7cf2cbf5b4b99d912bbc06aff4d Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Mon, 10 Aug 2009 21:59:16 -0300 Subject: V4L/DVB (12437): dvb: siano uses/depends on INPUT siano uses input_*() functions so it should depend on INPUT to prevent build errors: ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! Cc: Michael Krufky Cc: Uri Shkolnik Signed-off-by: Randy Dunlap Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/dvb/siano/Kconfig b/drivers/media/dvb/siano/Kconfig index dd863f261672..88847d1dcbb5 100644 --- a/drivers/media/dvb/siano/Kconfig +++ b/drivers/media/dvb/siano/Kconfig @@ -4,7 +4,7 @@ config DVB_SIANO_SMS1XXX tristate "Siano SMS1XXX USB dongle support" - depends on DVB_CORE && USB + depends on DVB_CORE && USB && INPUT ---help--- Choose Y here if you have a USB dongle with a SMS1XXX chipset. -- cgit v1.2.3 From bb2b4542b6415044894cd7c147ff54840dd8ed3f Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:07:54 -0300 Subject: V4L/DVB (12438): Read buffer overflow parport[n] is checked before n < MAX_CAMS Signed-off-by: Roel Kluin Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/video/bw-qcam.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/video/bw-qcam.c b/drivers/media/video/bw-qcam.c index 10dbd4a11b30..9e39bc5f7b00 100644 --- a/drivers/media/video/bw-qcam.c +++ b/drivers/media/video/bw-qcam.c @@ -992,7 +992,7 @@ static int accept_bwqcam(struct parport *port) if (parport[0] && strncmp(parport[0], "auto", 4) != 0) { /* user gave parport parameters */ - for(n=0; parport[n] && n Date: Mon, 10 Aug 2009 22:51:01 -0300 Subject: V4L/DVB (12440): Use kzalloc for frontend states to have struct dvb_frontend properly This patch changes most frontend drivers to allocate their state structure via kzalloc and not kmalloc. This is done to properly initialize the embedded "struct dvb_frontend frontend" field, that they all have. The visible effect of this struct being uninitalized is, that the member "id" that is used to set the name of kernel thread is totally random. Some board drivers (for example cx88-dvb) set this "id" via videobuf_dvb_alloc_frontend but most do not. So I at least get random id values for saa7134, flexcop and ttpci based cards. It looks like this in dmesg: DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S) The related kernel thread then also gets a strange name like "kdvb-ad-1-fe--1". Cc: Michael Krufky Cc: Steven Toth Cc: Timothy Lee Cc: Igor M. Liplianin Signed-off-by: Matthias Schwarzott Acked-by: Andreas Oberritter Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/frontends/cx22700.c | 2 +- drivers/media/dvb/frontends/cx22702.c | 2 +- drivers/media/dvb/frontends/cx24110.c | 2 +- drivers/media/dvb/frontends/dvb_dummy_fe.c | 6 +++--- drivers/media/dvb/frontends/l64781.c | 2 +- drivers/media/dvb/frontends/lgs8gl5.c | 2 +- drivers/media/dvb/frontends/mt312.c | 2 +- drivers/media/dvb/frontends/nxt6000.c | 2 +- drivers/media/dvb/frontends/or51132.c | 2 +- drivers/media/dvb/frontends/or51211.c | 2 +- drivers/media/dvb/frontends/s5h1409.c | 2 +- drivers/media/dvb/frontends/s5h1411.c | 2 +- drivers/media/dvb/frontends/si21xx.c | 2 +- drivers/media/dvb/frontends/sp8870.c | 2 +- drivers/media/dvb/frontends/sp887x.c | 2 +- drivers/media/dvb/frontends/stv0288.c | 2 +- drivers/media/dvb/frontends/stv0297.c | 2 +- drivers/media/dvb/frontends/stv0299.c | 2 +- drivers/media/dvb/frontends/tda10021.c | 2 +- drivers/media/dvb/frontends/tda10048.c | 2 +- drivers/media/dvb/frontends/tda1004x.c | 4 ++-- drivers/media/dvb/frontends/tda10086.c | 2 +- drivers/media/dvb/frontends/tda8083.c | 2 +- drivers/media/dvb/frontends/ves1820.c | 2 +- drivers/media/dvb/frontends/ves1x93.c | 2 +- 25 files changed, 28 insertions(+), 28 deletions(-) (limited to 'drivers') diff --git a/drivers/media/dvb/frontends/cx22700.c b/drivers/media/dvb/frontends/cx22700.c index ace5cb17165d..fbd838eca268 100644 --- a/drivers/media/dvb/frontends/cx22700.c +++ b/drivers/media/dvb/frontends/cx22700.c @@ -380,7 +380,7 @@ struct dvb_frontend* cx22700_attach(const struct cx22700_config* config, struct cx22700_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx22700_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx22700_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/cx22702.c b/drivers/media/dvb/frontends/cx22702.c index 5d1abe34bddb..00b5c7e91d5d 100644 --- a/drivers/media/dvb/frontends/cx22702.c +++ b/drivers/media/dvb/frontends/cx22702.c @@ -580,7 +580,7 @@ struct dvb_frontend *cx22702_attach(const struct cx22702_config *config, struct cx22702_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx22702_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx22702_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/cx24110.c b/drivers/media/dvb/frontends/cx24110.c index 87ae29db024f..ffbcfabd83f0 100644 --- a/drivers/media/dvb/frontends/cx24110.c +++ b/drivers/media/dvb/frontends/cx24110.c @@ -598,7 +598,7 @@ struct dvb_frontend* cx24110_attach(const struct cx24110_config* config, int ret; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct cx24110_state), GFP_KERNEL); + state = kzalloc(sizeof(struct cx24110_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/dvb_dummy_fe.c b/drivers/media/dvb/frontends/dvb_dummy_fe.c index db8a937cc630..a7fc7e53a551 100644 --- a/drivers/media/dvb/frontends/dvb_dummy_fe.c +++ b/drivers/media/dvb/frontends/dvb_dummy_fe.c @@ -117,7 +117,7 @@ struct dvb_frontend* dvb_dummy_fe_ofdm_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ @@ -137,7 +137,7 @@ struct dvb_frontend *dvb_dummy_fe_qpsk_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ @@ -157,7 +157,7 @@ struct dvb_frontend *dvb_dummy_fe_qam_attach(void) struct dvb_dummy_fe_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); + state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL); if (state == NULL) goto error; /* create dvb_frontend */ diff --git a/drivers/media/dvb/frontends/l64781.c b/drivers/media/dvb/frontends/l64781.c index e1e70e9e0cb9..3051b64aa17c 100644 --- a/drivers/media/dvb/frontends/l64781.c +++ b/drivers/media/dvb/frontends/l64781.c @@ -501,7 +501,7 @@ struct dvb_frontend* l64781_attach(const struct l64781_config* config, { .addr = config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } }; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct l64781_state), GFP_KERNEL); + state = kzalloc(sizeof(struct l64781_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/lgs8gl5.c b/drivers/media/dvb/frontends/lgs8gl5.c index 855852fddf22..bb37ed289a05 100644 --- a/drivers/media/dvb/frontends/lgs8gl5.c +++ b/drivers/media/dvb/frontends/lgs8gl5.c @@ -387,7 +387,7 @@ lgs8gl5_attach(const struct lgs8gl5_config *config, struct i2c_adapter *i2c) dprintk("%s\n", __func__); /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL); + state = kzalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/mt312.c b/drivers/media/dvb/frontends/mt312.c index a621f727935f..f69daaac78c9 100644 --- a/drivers/media/dvb/frontends/mt312.c +++ b/drivers/media/dvb/frontends/mt312.c @@ -782,7 +782,7 @@ struct dvb_frontend *mt312_attach(const struct mt312_config *config, struct mt312_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct mt312_state), GFP_KERNEL); + state = kzalloc(sizeof(struct mt312_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/nxt6000.c b/drivers/media/dvb/frontends/nxt6000.c index 0eef22dbf8a0..a763ec756f7f 100644 --- a/drivers/media/dvb/frontends/nxt6000.c +++ b/drivers/media/dvb/frontends/nxt6000.c @@ -545,7 +545,7 @@ struct dvb_frontend* nxt6000_attach(const struct nxt6000_config* config, struct nxt6000_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct nxt6000_state), GFP_KERNEL); + state = kzalloc(sizeof(struct nxt6000_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/or51132.c b/drivers/media/dvb/frontends/or51132.c index 8133ea3cddd7..38e67accb8c3 100644 --- a/drivers/media/dvb/frontends/or51132.c +++ b/drivers/media/dvb/frontends/or51132.c @@ -562,7 +562,7 @@ struct dvb_frontend* or51132_attach(const struct or51132_config* config, struct or51132_state* state = NULL; /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct or51132_state), GFP_KERNEL); + state = kzalloc(sizeof(struct or51132_state), GFP_KERNEL); if (state == NULL) return NULL; diff --git a/drivers/media/dvb/frontends/or51211.c b/drivers/media/dvb/frontends/or51211.c index 16cf2fdd5d7d..c709ce6771c8 100644 --- a/drivers/media/dvb/frontends/or51211.c +++ b/drivers/media/dvb/frontends/or51211.c @@ -527,7 +527,7 @@ struct dvb_frontend* or51211_attach(const struct or51211_config* config, struct or51211_state* state = NULL; /* Allocate memory for the internal state */ - state = kmalloc(sizeof(struct or51211_state), GFP_KERNEL); + state = kzalloc(sizeof(struct or51211_state), GFP_KERNEL); if (state == NULL) return NULL; diff --git a/drivers/media/dvb/frontends/s5h1409.c b/drivers/media/dvb/frontends/s5h1409.c index 3e08d985d6e5..fb3011518427 100644 --- a/drivers/media/dvb/frontends/s5h1409.c +++ b/drivers/media/dvb/frontends/s5h1409.c @@ -796,7 +796,7 @@ struct dvb_frontend *s5h1409_attach(const struct s5h1409_config *config, u16 reg; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct s5h1409_state), GFP_KERNEL); + state = kzalloc(sizeof(struct s5h1409_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/s5h1411.c b/drivers/media/dvb/frontends/s5h1411.c index 66e2dd6d6fe4..d8adf1e32019 100644 --- a/drivers/media/dvb/frontends/s5h1411.c +++ b/drivers/media/dvb/frontends/s5h1411.c @@ -844,7 +844,7 @@ struct dvb_frontend *s5h1411_attach(const struct s5h1411_config *config, u16 reg; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct s5h1411_state), GFP_KERNEL); + state = kzalloc(sizeof(struct s5h1411_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/si21xx.c b/drivers/media/dvb/frontends/si21xx.c index 0bd16af8a6cd..9552a22ccffb 100644 --- a/drivers/media/dvb/frontends/si21xx.c +++ b/drivers/media/dvb/frontends/si21xx.c @@ -928,7 +928,7 @@ struct dvb_frontend *si21xx_attach(const struct si21xx_config *config, dprintk("%s\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct si21xx_state), GFP_KERNEL); + state = kzalloc(sizeof(struct si21xx_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/sp8870.c b/drivers/media/dvb/frontends/sp8870.c index 1c9a9b4051b9..b85eb60a893e 100644 --- a/drivers/media/dvb/frontends/sp8870.c +++ b/drivers/media/dvb/frontends/sp8870.c @@ -557,7 +557,7 @@ struct dvb_frontend* sp8870_attach(const struct sp8870_config* config, struct sp8870_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct sp8870_state), GFP_KERNEL); + state = kzalloc(sizeof(struct sp8870_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/sp887x.c b/drivers/media/dvb/frontends/sp887x.c index 559509ab4dab..4a7c3d842608 100644 --- a/drivers/media/dvb/frontends/sp887x.c +++ b/drivers/media/dvb/frontends/sp887x.c @@ -557,7 +557,7 @@ struct dvb_frontend* sp887x_attach(const struct sp887x_config* config, struct sp887x_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct sp887x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct sp887x_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/stv0288.c b/drivers/media/dvb/frontends/stv0288.c index ff1194de34c0..2930a5d6768a 100644 --- a/drivers/media/dvb/frontends/stv0288.c +++ b/drivers/media/dvb/frontends/stv0288.c @@ -570,7 +570,7 @@ struct dvb_frontend *stv0288_attach(const struct stv0288_config *config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0288_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0288_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/stv0297.c b/drivers/media/dvb/frontends/stv0297.c index 62caf802ed99..4fd7479bb62b 100644 --- a/drivers/media/dvb/frontends/stv0297.c +++ b/drivers/media/dvb/frontends/stv0297.c @@ -663,7 +663,7 @@ struct dvb_frontend *stv0297_attach(const struct stv0297_config *config, struct stv0297_state *state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0297_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0297_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/stv0299.c b/drivers/media/dvb/frontends/stv0299.c index 6c1cb1973c6e..968874469726 100644 --- a/drivers/media/dvb/frontends/stv0299.c +++ b/drivers/media/dvb/frontends/stv0299.c @@ -667,7 +667,7 @@ struct dvb_frontend* stv0299_attach(const struct stv0299_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct stv0299_state), GFP_KERNEL); + state = kzalloc(sizeof(struct stv0299_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/tda10021.c b/drivers/media/dvb/frontends/tda10021.c index f648fdb64bb7..f5d7b3277a2f 100644 --- a/drivers/media/dvb/frontends/tda10021.c +++ b/drivers/media/dvb/frontends/tda10021.c @@ -413,7 +413,7 @@ struct dvb_frontend* tda10021_attach(const struct tda1002x_config* config, u8 id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10021_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10021_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/tda10048.c b/drivers/media/dvb/frontends/tda10048.c index cc8862ce4aae..4e2a7c8b2f62 100644 --- a/drivers/media/dvb/frontends/tda10048.c +++ b/drivers/media/dvb/frontends/tda10048.c @@ -1095,7 +1095,7 @@ struct dvb_frontend *tda10048_attach(const struct tda10048_config *config, dprintk(1, "%s()\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10048_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10048_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/tda1004x.c b/drivers/media/dvb/frontends/tda1004x.c index 4981cef8b444..f2a8abe0a243 100644 --- a/drivers/media/dvb/frontends/tda1004x.c +++ b/drivers/media/dvb/frontends/tda1004x.c @@ -1269,7 +1269,7 @@ struct dvb_frontend* tda10045_attach(const struct tda1004x_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL); if (!state) { printk(KERN_ERR "Can't alocate memory for tda10045 state\n"); return NULL; @@ -1339,7 +1339,7 @@ struct dvb_frontend* tda10046_attach(const struct tda1004x_config* config, int id; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL); if (!state) { printk(KERN_ERR "Can't alocate memory for tda10046 state\n"); return NULL; diff --git a/drivers/media/dvb/frontends/tda10086.c b/drivers/media/dvb/frontends/tda10086.c index a17ce3c4ad86..f2c8faac6f36 100644 --- a/drivers/media/dvb/frontends/tda10086.c +++ b/drivers/media/dvb/frontends/tda10086.c @@ -745,7 +745,7 @@ struct dvb_frontend* tda10086_attach(const struct tda10086_config* config, dprintk ("%s\n", __func__); /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda10086_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda10086_state), GFP_KERNEL); if (!state) return NULL; diff --git a/drivers/media/dvb/frontends/tda8083.c b/drivers/media/dvb/frontends/tda8083.c index 5b843b2e67e8..9369f7442f27 100644 --- a/drivers/media/dvb/frontends/tda8083.c +++ b/drivers/media/dvb/frontends/tda8083.c @@ -417,7 +417,7 @@ struct dvb_frontend* tda8083_attach(const struct tda8083_config* config, struct tda8083_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda8083_state), GFP_KERNEL); + state = kzalloc(sizeof(struct tda8083_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ diff --git a/drivers/media/dvb/frontends/ves1820.c b/drivers/media/dvb/frontends/ves1820.c index a184597f1d9b..6e78e4865515 100644 --- a/drivers/media/dvb/frontends/ves1820.c +++ b/drivers/media/dvb/frontends/ves1820.c @@ -374,7 +374,7 @@ struct dvb_frontend* ves1820_attach(const struct ves1820_config* config, struct ves1820_state* state = NULL; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct ves1820_state), GFP_KERNEL); + state = kzalloc(sizeof(struct ves1820_state), GFP_KERNEL); if (state == NULL) goto error; diff --git a/drivers/media/dvb/frontends/ves1x93.c b/drivers/media/dvb/frontends/ves1x93.c index bd558960bd87..8d7854c2fb0c 100644 --- a/drivers/media/dvb/frontends/ves1x93.c +++ b/drivers/media/dvb/frontends/ves1x93.c @@ -456,7 +456,7 @@ struct dvb_frontend* ves1x93_attach(const struct ves1x93_config* config, u8 identity; /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct ves1x93_state), GFP_KERNEL); + state = kzalloc(sizeof(struct ves1x93_state), GFP_KERNEL); if (state == NULL) goto error; /* setup the state */ -- cgit v1.2.3 From 08b39642b1e375afd014c50f6013ec4a292ca3b2 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Mon, 10 Aug 2009 22:59:33 -0300 Subject: V4L/DVB (12441): siano: read buffer overflow With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[]. Subsequently an attempt is made to load the firmware from the resulting filename. Signed-off-by: Roel Kluin Signed-off-by: Andrew Morton Signed-off-by: Douglas Schilling Landgraf Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb/siano/smscoreapi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/media/dvb/siano/smscoreapi.c b/drivers/media/dvb/siano/smscoreapi.c index a246903c3341..bd9ab9d0d12a 100644 --- a/drivers/media/dvb/siano/smscoreapi.c +++ b/drivers/media/dvb/siano/smscoreapi.c @@ -816,7 +816,7 @@ int smscore_set_device_mode(struct smscore_device_t *coredev, int mode) sms_debug("set device mode to %d", mode); if (coredev->device_flags & SMS_DEVICE_FAMILY2) { - if (mode < DEVICE_MODE_DVBT || mode > DEVICE_MODE_RAW_TUNER) { + if (mode < DEVICE_MODE_DVBT || mode >= DEVICE_MODE_RAW_TUNER) { sms_err("invalid mode specified %d", mode); return -EINVAL; } -- cgit v1.2.3 From a219dc4d4463809b1be473038e7d9f3437ca452d Mon Sep 17 00:00:00 2001 From: Ramax Lo Date: Wed, 12 Aug 2009 23:55:56 +0800 Subject: ARM: S3C64XX: serial: Fix a typo in Kconfig The typo causes drivers/serial/s3c6400.c not being built for s3c6400 platform. Signed-off-by: Ramax Lo Signed-off-by: Ben Dooks --- drivers/serial/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 037c1e0b7c4c..6553833c12db 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -527,7 +527,7 @@ config SERIAL_S3C24A0 config SERIAL_S3C6400 tristate "Samsung S3C6400/S3C6410 Serial port support" - depends on SERIAL_SAMSUNG && (CPU_S3C600 || CPU_S3C6410) + depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410) default y help Serial port support for the Samsung S3C6400 and S3C6410 -- cgit v1.2.3 From 17e78b0655da20f2fc2bbde3b8252dac07c82914 Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Thu, 13 Aug 2009 14:09:58 +0000 Subject: ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that have been DDPed. However, it is possible that the length is 0, e.g., for SCSI READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP, we do not want to return the 0 ddp->len as we want FCP_RSP to be always delivered to the upper layer. This patch fixes this bug by setting rc only if ddp->len is non-zero. Signed-off-by: Yi Zou Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_fcoe.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_fcoe.c b/drivers/net/ixgbe/ixgbe_fcoe.c index fa9f24e23683..28cf104e36cc 100644 --- a/drivers/net/ixgbe/ixgbe_fcoe.c +++ b/drivers/net/ixgbe/ixgbe_fcoe.c @@ -336,7 +336,7 @@ int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter, /* return 0 to bypass going to ULD for DDPed data */ if (fcstat == IXGBE_RXDADV_STAT_FCSTAT_DDP) rc = 0; - else + else if (ddp->len) rc = ddp->len; } -- cgit v1.2.3 From 8a62babfb87aa5911e87e0ce38381bdfdc4a2b83 Mon Sep 17 00:00:00 2001 From: Lucy Liu Date: Thu, 13 Aug 2009 14:09:38 +0000 Subject: ixgbe: Fix receive on real device when VLANs are configured Traffic received with a priority tag (VID = 0) and non-zero priority value was incorrectly handled by the VLAN packet code path due to a check on zero for the whole VLAN tag instead of just the VID. This patch masked out the priority field when checking the vlan tag for received VLAN packets. Signed-off-by: Lucy Liu Acked-by: Peter P Waskiewicz Jr Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ixgbe/ixgbe_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index e3cb949b9aa9..77b0381a2b5c 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -492,12 +492,12 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector, skb_record_rx_queue(skb, ring->queue_index); if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL)) { - if (adapter->vlgrp && is_vlan && (tag != 0)) + if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK)) vlan_gro_receive(napi, adapter->vlgrp, tag, skb); else napi_gro_receive(napi, skb); } else { - if (adapter->vlgrp && is_vlan && (tag != 0)) + if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK)) vlan_hwaccel_rx(skb, adapter->vlgrp, tag); else netif_rx(skb); -- cgit v1.2.3 From 6b26dead3ce97d016b57724b01974d5ca5c84bd5 Mon Sep 17 00:00:00 2001 From: Pavel Roskin Date: Tue, 4 Aug 2009 17:48:16 -0400 Subject: rt2x00: fix memory corruption in rf cache, add a sanity check Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf register number. This is needed because the rf registers are enumerated starting with one. The size of the rf register cache is just enough to hold all registers, so writing to the highest register was corrupting memory. Add a check to make sure that the rf register number is valid. Signed-off-by: Pavel Roskin Cc: stable@kernel.org Acked-by: Ivo van Doorn Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2x00.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h index a498dde024e1..49c9e2c1433d 100644 --- a/drivers/net/wireless/rt2x00/rt2x00.h +++ b/drivers/net/wireless/rt2x00/rt2x00.h @@ -849,13 +849,15 @@ struct rt2x00_dev { static inline void rt2x00_rf_read(struct rt2x00_dev *rt2x00dev, const unsigned int word, u32 *data) { - *data = rt2x00dev->rf[word]; + BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32)); + *data = rt2x00dev->rf[word - 1]; } static inline void rt2x00_rf_write(struct rt2x00_dev *rt2x00dev, const unsigned int word, u32 data) { - rt2x00dev->rf[word] = data; + BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32)); + rt2x00dev->rf[word - 1] = data; } /* -- cgit v1.2.3 From 0527a1a8440a20b3d0fd1d0c9e75a6f38a9d5315 Mon Sep 17 00:00:00 2001 From: roel kluin Date: Fri, 14 Aug 2009 02:09:56 +0000 Subject: via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL Test whether VELOCITY_DUPLEX_FULL bit is set in mii_status. Signed-off-by: Roel Kluin Signed-off-by: David S. Miller --- drivers/net/via-velocity.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c index 3ba35956327a..cee08a1e497a 100644 --- a/drivers/net/via-velocity.c +++ b/drivers/net/via-velocity.c @@ -1778,7 +1778,7 @@ static void velocity_error(struct velocity_info *vptr, int status) * mode */ if (vptr->rev_id < REV_ID_VT3216_A0) { - if (vptr->mii_status | VELOCITY_DUPLEX_FULL) + if (vptr->mii_status & VELOCITY_DUPLEX_FULL) BYTE_REG_BITS_ON(TCR_TB2BDIS, ®s->TCR); else BYTE_REG_BITS_OFF(TCR_TB2BDIS, ®s->TCR); -- cgit v1.2.3 From 22580f894ac190c46beebb5c3172e450a2318f79 Mon Sep 17 00:00:00 2001 From: Dongdong Deng Date: Thu, 13 Aug 2009 19:12:31 +0000 Subject: drivers/net: fixed drivers that support netpoll use ndo_start_xmit() The NETPOLL API requires that interrupts remain disabled in netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq() in the NETPOLL API callbacks causes the interrupts to get enabled and can lead to kernel instability. The solution is to use spin_lock_irqsave() and spin_unlock_restore() to prevent the irqs from getting enabled while in netpoll_send_skb(). Call trace: netpoll_send_skb() { -> local_irq_save(flags) ---> dev->ndo_start_xmit(skb, dev) ---> spin_lock_irq() ---> spin_unlock_irq() *******here would enable the interrupt. ... -> local_irq_restore(flags) } Signed-off-by: Dongdong Deng Signed-off-by: Jason Wessel Acked-by: Bruce Ashfield Acked-by: Matt Mackall Signed-off-by: David S. Miller --- drivers/net/b44.c | 5 +++-- drivers/net/tulip/tulip_core.c | 5 +++-- drivers/net/ucc_geth.c | 5 +++-- drivers/net/via-rhine.c | 5 +++-- 4 files changed, 12 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/b44.c b/drivers/net/b44.c index 36d4d377ec2f..bafca672ea7d 100644 --- a/drivers/net/b44.c +++ b/drivers/net/b44.c @@ -952,9 +952,10 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) int rc = NETDEV_TX_OK; dma_addr_t mapping; u32 len, entry, ctrl; + unsigned long flags; len = skb->len; - spin_lock_irq(&bp->lock); + spin_lock_irqsave(&bp->lock, flags); /* This is a hard error, log it. */ if (unlikely(TX_BUFFS_AVAIL(bp) < 1)) { @@ -1027,7 +1028,7 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) dev->trans_start = jiffies; out_unlock: - spin_unlock_irq(&bp->lock); + spin_unlock_irqrestore(&bp->lock, flags); return rc; diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c index 99a63649f4fc..4cf9a6588751 100644 --- a/drivers/net/tulip/tulip_core.c +++ b/drivers/net/tulip/tulip_core.c @@ -652,8 +652,9 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev) int entry; u32 flag; dma_addr_t mapping; + unsigned long flags; - spin_lock_irq(&tp->lock); + spin_lock_irqsave(&tp->lock, flags); /* Calculate the next Tx descriptor entry. */ entry = tp->cur_tx % TX_RING_SIZE; @@ -688,7 +689,7 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev) /* Trigger an immediate transmit demand. */ iowrite32(0, tp->base_addr + CSR1); - spin_unlock_irq(&tp->lock); + spin_unlock_irqrestore(&tp->lock, flags); dev->trans_start = jiffies; diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index 3b957e6412ee..8a7b8c7bd781 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -3111,10 +3111,11 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev) u8 __iomem *bd; /* BD pointer */ u32 bd_status; u8 txQ = 0; + unsigned long flags; ugeth_vdbg("%s: IN", __func__); - spin_lock_irq(&ugeth->lock); + spin_lock_irqsave(&ugeth->lock, flags); dev->stats.tx_bytes += skb->len; @@ -3171,7 +3172,7 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev) uccf = ugeth->uccf; out_be16(uccf->p_utodr, UCC_FAST_TOD); #endif - spin_unlock_irq(&ugeth->lock); + spin_unlock_irqrestore(&ugeth->lock, flags); return 0; } diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c index 88c30a58b4bd..934f7671650a 100644 --- a/drivers/net/via-rhine.c +++ b/drivers/net/via-rhine.c @@ -1218,6 +1218,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) struct rhine_private *rp = netdev_priv(dev); void __iomem *ioaddr = rp->base; unsigned entry; + unsigned long flags; /* Caution: the write order is important here, set the field with the "ownership" bits last. */ @@ -1261,7 +1262,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) cpu_to_le32(TXDESC | (skb->len >= ETH_ZLEN ? skb->len : ETH_ZLEN)); /* lock eth irq */ - spin_lock_irq(&rp->lock); + spin_lock_irqsave(&rp->lock, flags); wmb(); rp->tx_ring[entry].tx_status = cpu_to_le32(DescOwn); wmb(); @@ -1280,7 +1281,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev) dev->trans_start = jiffies; - spin_unlock_irq(&rp->lock); + spin_unlock_irqrestore(&rp->lock, flags); if (debug > 4) { printk(KERN_DEBUG "%s: Transmit frame #%d queued in slot %d.\n", -- cgit v1.2.3 From 7c1d15d736687057f4dc6e51fbf44b6f6e4320cb Mon Sep 17 00:00:00 2001 From: Petko Manolov Date: Fri, 14 Aug 2009 06:40:48 +0000 Subject: pegasus: Add new device ID. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add new definition to 'pegasus.h' for support Japanese IO DATA "ETX-US2" USB Ethernet Adapter. PEGASUS_DEV( $B!H(BIO DATA USB ETX-US2$B!I(B, VENDOR_IODATA, 0x092a, DEFAULT_GPIO_RESET | PEGASUS_II ) Signed-off-by: David S. Miller --- drivers/net/usb/pegasus.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/net/usb/pegasus.h b/drivers/net/usb/pegasus.h index c7467823cd1c..f968c834ff63 100644 --- a/drivers/net/usb/pegasus.h +++ b/drivers/net/usb/pegasus.h @@ -250,6 +250,8 @@ PEGASUS_DEV( "IO DATA USB ET/TX", VENDOR_IODATA, 0x0904, DEFAULT_GPIO_RESET ) PEGASUS_DEV( "IO DATA USB ET/TX-S", VENDOR_IODATA, 0x0913, DEFAULT_GPIO_RESET | PEGASUS_II ) +PEGASUS_DEV( "IO DATA USB ETX-US2", VENDOR_IODATA, 0x092a, + DEFAULT_GPIO_RESET | PEGASUS_II ) PEGASUS_DEV( "Kingston KNU101TX Ethernet", VENDOR_KINGSTON, 0x000a, DEFAULT_GPIO_RESET) PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x4002, -- cgit v1.2.3 From 616b8434688aa08bd6f019cc60c8dfe121e9e5ae Mon Sep 17 00:00:00 2001 From: Jerome Glisse Date: Thu, 6 Aug 2009 17:47:24 +0200 Subject: drm/radeon/kms: Add specific rs690 authorized register table rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow AVIVO register for vline synchronization. This add a specific table to rs690 to handle that. Thanks to Marc (marvin24) for debugging this and kudos to Andre (taiu1) for spotting the origin of the bugs. Signed-off-by: Jerome Glisse Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_asic.h | 3 +- drivers/gpu/drm/radeon/rs690.c | 65 ++++++++++++++++++++++++++++++++++++ 2 files changed, 67 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index 9a75876e0c3b..c0ae2d923254 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -308,6 +308,7 @@ static struct radeon_asic rs600_asic = { /* * rs690,rs740 */ +int rs690_init(struct radeon_device *rdev); void rs690_errata(struct radeon_device *rdev); void rs690_vram_info(struct radeon_device *rdev); int rs690_mc_init(struct radeon_device *rdev); @@ -316,7 +317,7 @@ uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg); void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v); void rs690_bandwidth_update(struct radeon_device *rdev); static struct radeon_asic rs690_asic = { - .init = &r300_init, + .init = &rs690_init, .errata = &rs690_errata, .vram_info = &rs690_vram_info, .gpu_reset = &r300_gpu_reset, diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c index 839595b00728..bc6b7c5339bc 100644 --- a/drivers/gpu/drm/radeon/rs690.c +++ b/drivers/gpu/drm/radeon/rs690.c @@ -652,3 +652,68 @@ void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) WREG32(RS690_MC_DATA, v); WREG32(RS690_MC_INDEX, RS690_MC_INDEX_WR_ACK); } + +static const unsigned rs690_reg_safe_bm[219] = { + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0x17FF1FFF,0xFFFFFFFC,0xFFFFFFFF,0xFF30FFBF, + 0xFFFFFFF8,0xC3E6FFFF,0xFFFFF6DF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFF03F, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFEFCE,0xF00EBFFF,0x007C0000, + 0xF0000078,0xFF000009,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFF7FF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFC78,0xFFFFFFFF,0xFFFFFFFE,0xFFFFFFFF, + 0x38FF8F50,0xFFF88082,0xF000000C,0xFAE009FF, + 0x0000FFFF,0xFFFFFFFF,0xFFFFFFFF,0x00000000, + 0x00000000,0x0000C100,0x00000000,0x00000000, + 0x00000000,0x00000000,0x00000000,0x00000000, + 0x00000000,0xFFFF0000,0xFFFFFFFF,0xFF80FFFF, + 0x00000000,0x00000000,0x00000000,0x00000000, + 0x0003FC01,0xFFFFFFF8,0xFE800B19,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, + 0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF, +}; + +int rs690_init(struct radeon_device *rdev) +{ + rdev->config.r300.reg_safe_bm = rs690_reg_safe_bm; + rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(rs690_reg_safe_bm); + return 0; +} -- cgit v1.2.3 From ebb177d2afb8532a8a316489aed545ed0c170802 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 15 Aug 2009 12:25:08 +1000 Subject: drm/edid: fixup detailed timings like the X server. this syncs the versioning check with the code the X server uses. Reported-by: Anssi Hannula Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_edid.c | 72 ++++++++++++++++++++++------------------------ 1 file changed, 34 insertions(+), 38 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c index 80cc6d06d61b..7f2728bbc16c 100644 --- a/drivers/gpu/drm/drm_edid.c +++ b/drivers/gpu/drm/drm_edid.c @@ -502,12 +502,40 @@ static int add_detailed_info(struct drm_connector *connector, struct detailed_non_pixel *data = &timing->data.other_data; struct drm_display_mode *newmode; - /* EDID up to and including 1.2 may put monitor info here */ - if (edid->version == 1 && edid->revision < 3) - continue; - - /* Detailed mode timing */ - if (timing->pixel_clock) { + /* X server check is version 1.1 or higher */ + if (edid->version == 1 && edid->revision >= 1 && + !timing->pixel_clock) { + /* Other timing or info */ + switch (data->type) { + case EDID_DETAIL_MONITOR_SERIAL: + break; + case EDID_DETAIL_MONITOR_STRING: + break; + case EDID_DETAIL_MONITOR_RANGE: + /* Get monitor range data */ + break; + case EDID_DETAIL_MONITOR_NAME: + break; + case EDID_DETAIL_MONITOR_CPDATA: + break; + case EDID_DETAIL_STD_MODES: + /* Five modes per detailed section */ + for (j = 0; j < 5; i++) { + struct std_timing *std; + struct drm_display_mode *newmode; + + std = &data->data.timings[j]; + newmode = drm_mode_std(dev, std); + if (newmode) { + drm_mode_probed_add(connector, newmode); + modes++; + } + } + break; + default: + break; + } + } else { newmode = drm_mode_detailed(dev, edid, timing, quirks); if (!newmode) continue; @@ -518,38 +546,6 @@ static int add_detailed_info(struct drm_connector *connector, drm_mode_probed_add(connector, newmode); modes++; - continue; - } - - /* Other timing or info */ - switch (data->type) { - case EDID_DETAIL_MONITOR_SERIAL: - break; - case EDID_DETAIL_MONITOR_STRING: - break; - case EDID_DETAIL_MONITOR_RANGE: - /* Get monitor range data */ - break; - case EDID_DETAIL_MONITOR_NAME: - break; - case EDID_DETAIL_MONITOR_CPDATA: - break; - case EDID_DETAIL_STD_MODES: - /* Five modes per detailed section */ - for (j = 0; j < 5; i++) { - struct std_timing *std; - struct drm_display_mode *newmode; - - std = &data->data.timings[j]; - newmode = drm_mode_std(dev, std); - if (newmode) { - drm_mode_probed_add(connector, newmode); - modes++; - } - } - break; - default: - break; } } -- cgit v1.2.3 From 21bc1f024d0d4ea43fc0f2a43504e759261c7b18 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:16 +0000 Subject: sh: skip disabled LCDC channels This patch updates the SuperH Mobile LCDC driver to skip over disabled channels. Without this patch suspend-to-ram operation will crash if deferred io is enabled. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- drivers/video/sh_mobile_lcdcfb.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers') diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c index 8f24564f77b0..07f22b625632 100644 --- a/drivers/video/sh_mobile_lcdcfb.c +++ b/drivers/video/sh_mobile_lcdcfb.c @@ -481,6 +481,9 @@ static int sh_mobile_lcdc_start(struct sh_mobile_lcdc_priv *priv) /* tell the board code to enable the panel */ for (k = 0; k < ARRAY_SIZE(priv->ch); k++) { ch = &priv->ch[k]; + if (!ch->enabled) + continue; + board_cfg = &ch->cfg.board_cfg; if (board_cfg->display_on) board_cfg->display_on(board_cfg->board_data); @@ -498,6 +501,8 @@ static void sh_mobile_lcdc_stop(struct sh_mobile_lcdc_priv *priv) /* clean up deferred io and ask board code to disable panel */ for (k = 0; k < ARRAY_SIZE(priv->ch); k++) { ch = &priv->ch[k]; + if (!ch->enabled) + continue; /* deferred io mode: * flush frame, and wait for frame end interrupt -- cgit v1.2.3 From f6431732f128a241b149c0aa85dfec852455ebf9 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Sat, 15 Aug 2009 02:53:25 +0000 Subject: sh: CMT suspend/resume This patch updates the SuperH CMT driver with suspend and resume callbacks for the suspend-to-ram case. This patch stops the CMT channel at suspend time to avoid unwanted wake up events. Signed-off-by: Magnus Damm Signed-off-by: Paul Mundt --- drivers/clocksource/sh_cmt.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) (limited to 'drivers') diff --git a/drivers/clocksource/sh_cmt.c b/drivers/clocksource/sh_cmt.c index 2964f5f4a7ef..6b3e0c2f33e2 100644 --- a/drivers/clocksource/sh_cmt.c +++ b/drivers/clocksource/sh_cmt.c @@ -40,6 +40,7 @@ struct sh_cmt_priv { struct platform_device *pdev; unsigned long flags; + unsigned long flags_suspend; unsigned long match_value; unsigned long next_match_value; unsigned long max_match_value; @@ -667,11 +668,38 @@ static int __devexit sh_cmt_remove(struct platform_device *pdev) return -EBUSY; /* cannot unregister clockevent and clocksource */ } +static int sh_cmt_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct sh_cmt_priv *p = platform_get_drvdata(pdev); + + /* save flag state and stop CMT channel */ + p->flags_suspend = p->flags; + sh_cmt_stop(p, p->flags); + return 0; +} + +static int sh_cmt_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct sh_cmt_priv *p = platform_get_drvdata(pdev); + + /* start CMT channel from saved state */ + sh_cmt_start(p, p->flags_suspend); + return 0; +} + +static struct dev_pm_ops sh_cmt_dev_pm_ops = { + .suspend = sh_cmt_suspend, + .resume = sh_cmt_resume, +}; + static struct platform_driver sh_cmt_device_driver = { .probe = sh_cmt_probe, .remove = __devexit_p(sh_cmt_remove), .driver = { .name = "sh_cmt", + .pm = &sh_cmt_dev_pm_ops, } }; -- cgit v1.2.3 From 3f8befec95d5c1bbc6e247e1a5dafa82519530f9 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sat, 15 Aug 2009 20:54:13 +1000 Subject: drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR These are needed for Occulsion Query support. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r300.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 9c8d41534a5d..8594486e1625 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -1403,6 +1403,21 @@ static int r300_packet0_check(struct radeon_cs_parser *p, tmp = (ib_chunk->kdata[idx] >> 22) & 0xF; track->textures[i].txdepth = tmp; break; + case R300_ZB_ZPASS_ADDR: + r = r100_cs_packet_next_reloc(p, &reloc); + if (r) { + DRM_ERROR("No reloc for ib[%d]=0x%04X\n", + idx, reg); + r100_cs_dump_packet(p, pkt); + return r; + } + ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset); + break; + case 0x4be8: + /* valid register only on RV530 */ + if (p->rdev->family == CHIP_RV530) + break; + /* fallthrough do not move */ default: printk(KERN_ERR "Forbidden register 0x%04X in cs at %d\n", reg, idx); -- cgit v1.2.3 From 7ed220d738cf16adff6bc3b31ad25b8848a2fa9c Mon Sep 17 00:00:00 2001 From: Michel Dänzer Date: Thu, 13 Aug 2009 11:10:51 +0200 Subject: drm/radeon/kms: Fix up vertical blank interrupt support. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fixes 3D apps timing out in the WAIT_VBLANK ioctl. AVIVO bits compile-tested only. Signed-off-by: Michel Dänzer Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 66 +++++++++++++++++++++++ drivers/gpu/drm/radeon/r500_reg.h | 16 ++++-- drivers/gpu/drm/radeon/radeon.h | 2 + drivers/gpu/drm/radeon/radeon_asic.h | 23 +++++--- drivers/gpu/drm/radeon/radeon_irq_kms.c | 54 ------------------- drivers/gpu/drm/radeon/radeon_kms.c | 33 ++++++++++-- drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 7 ++- drivers/gpu/drm/radeon/radeon_reg.h | 11 ++-- drivers/gpu/drm/radeon/rs600.c | 82 +++++++++++++++++++++++++++++ 9 files changed, 217 insertions(+), 77 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index f1ba8ff41130..e1a6e82b9960 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -253,6 +253,72 @@ void r100_mc_fini(struct radeon_device *rdev) } +/* + * Interrupts + */ +int r100_irq_set(struct radeon_device *rdev) +{ + uint32_t tmp = 0; + + if (rdev->irq.sw_int) { + tmp |= RADEON_SW_INT_ENABLE; + } + if (rdev->irq.crtc_vblank_int[0]) { + tmp |= RADEON_CRTC_VBLANK_MASK; + } + if (rdev->irq.crtc_vblank_int[1]) { + tmp |= RADEON_CRTC2_VBLANK_MASK; + } + WREG32(RADEON_GEN_INT_CNTL, tmp); + return 0; +} + +static inline uint32_t r100_irq_ack(struct radeon_device *rdev) +{ + uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); + uint32_t irq_mask = RADEON_SW_INT_TEST | RADEON_CRTC_VBLANK_STAT | + RADEON_CRTC2_VBLANK_STAT; + + if (irqs) { + WREG32(RADEON_GEN_INT_STATUS, irqs); + } + return irqs & irq_mask; +} + +int r100_irq_process(struct radeon_device *rdev) +{ + uint32_t status; + + status = r100_irq_ack(rdev); + if (!status) { + return IRQ_NONE; + } + while (status) { + /* SW interrupt */ + if (status & RADEON_SW_INT_TEST) { + radeon_fence_process(rdev); + } + /* Vertical blank interrupts */ + if (status & RADEON_CRTC_VBLANK_STAT) { + drm_handle_vblank(rdev->ddev, 0); + } + if (status & RADEON_CRTC2_VBLANK_STAT) { + drm_handle_vblank(rdev->ddev, 1); + } + status = r100_irq_ack(rdev); + } + return IRQ_HANDLED; +} + +u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc) +{ + if (crtc == 0) + return RREG32(RADEON_CRTC_CRNT_FRAME); + else + return RREG32(RADEON_CRTC2_CRNT_FRAME); +} + + /* * Fence emission */ diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h index 036691b38cb7..e1d5e0331e19 100644 --- a/drivers/gpu/drm/radeon/r500_reg.h +++ b/drivers/gpu/drm/radeon/r500_reg.h @@ -350,6 +350,7 @@ #define AVIVO_D1CRTC_BLANK_CONTROL 0x6084 #define AVIVO_D1CRTC_INTERLACE_CONTROL 0x6088 #define AVIVO_D1CRTC_INTERLACE_STATUS 0x608c +#define AVIVO_D1CRTC_FRAME_COUNT 0x60a4 #define AVIVO_D1CRTC_STEREO_CONTROL 0x60c4 /* master controls */ @@ -438,14 +439,15 @@ # define AVIVO_DC_LB_DISP1_END_ADR_SHIFT 4 # define AVIVO_DC_LB_DISP1_END_ADR_MASK 0x7ff -#define R500_DxMODE_INT_MASK 0x6540 -#define R500_D1MODE_INT_MASK (1<<0) -#define R500_D2MODE_INT_MASK (1<<8) - #define AVIVO_D1MODE_DATA_FORMAT 0x6528 # define AVIVO_D1MODE_INTERLEAVE_EN (1 << 0) #define AVIVO_D1MODE_DESKTOP_HEIGHT 0x652C +#define AVIVO_D1MODE_VBLANK_STATUS 0x6534 +# define AVIVO_VBLANK_ACK (1 << 4) #define AVIVO_D1MODE_VLINE_START_END 0x6538 +#define AVIVO_DxMODE_INT_MASK 0x6540 +# define AVIVO_D1MODE_INT_MASK (1 << 0) +# define AVIVO_D2MODE_INT_MASK (1 << 8) #define AVIVO_D1MODE_VIEWPORT_START 0x6580 #define AVIVO_D1MODE_VIEWPORT_SIZE 0x6584 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6588 @@ -475,6 +477,7 @@ #define AVIVO_D2CRTC_BLANK_CONTROL 0x6884 #define AVIVO_D2CRTC_INTERLACE_CONTROL 0x6888 #define AVIVO_D2CRTC_INTERLACE_STATUS 0x688c +#define AVIVO_D2CRTC_FRAME_COUNT 0x68a4 #define AVIVO_D2CRTC_STEREO_CONTROL 0x68c4 #define AVIVO_D2GRPH_ENABLE 0x6900 @@ -497,6 +500,7 @@ #define AVIVO_D2CUR_SIZE 0x6c10 #define AVIVO_D2CUR_POSITION 0x6c14 +#define AVIVO_D2MODE_VBLANK_STATUS 0x6d34 #define AVIVO_D2MODE_VLINE_START_END 0x6d38 #define AVIVO_D2MODE_VIEWPORT_START 0x6d80 #define AVIVO_D2MODE_VIEWPORT_SIZE 0x6d84 @@ -748,4 +752,8 @@ # define AVIVO_I2C_EN (1 << 0) # define AVIVO_I2C_RESET (1 << 8) +#define AVIVO_DISP_INTERRUPT_STATUS 0x7edc +# define AVIVO_D1_VBLANK_INTERRUPT (1 << 4) +# define AVIVO_D2_VBLANK_INTERRUPT (1 << 5) + #endif diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index b1d945b8ed6c..346112740846 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -574,6 +574,7 @@ struct radeon_asic { void (*ring_start)(struct radeon_device *rdev); int (*irq_set)(struct radeon_device *rdev); int (*irq_process)(struct radeon_device *rdev); + u32 (*get_vblank_counter)(struct radeon_device *rdev, int crtc); void (*fence_ring_emit)(struct radeon_device *rdev, struct radeon_fence *fence); int (*cs_parse)(struct radeon_cs_parser *p); int (*copy_blit)(struct radeon_device *rdev, @@ -862,6 +863,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v) #define radeon_ring_start(rdev) (rdev)->asic->ring_start((rdev)) #define radeon_irq_set(rdev) (rdev)->asic->irq_set((rdev)) #define radeon_irq_process(rdev) (rdev)->asic->irq_process((rdev)) +#define radeon_get_vblank_counter(rdev, crtc) (rdev)->asic->get_vblank_counter((rdev), (crtc)) #define radeon_fence_ring_emit(rdev, fence) (rdev)->asic->fence_ring_emit((rdev), (fence)) #define radeon_copy_blit(rdev, s, d, np, f) (rdev)->asic->copy_blit((rdev), (s), (d), (np), (f)) #define radeon_copy_dma(rdev, s, d, np, f) (rdev)->asic->copy_dma((rdev), (s), (d), (np), (f)) diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h index c0ae2d923254..7ca6c13569b5 100644 --- a/drivers/gpu/drm/radeon/radeon_asic.h +++ b/drivers/gpu/drm/radeon/radeon_asic.h @@ -49,6 +49,7 @@ void r100_vram_info(struct radeon_device *rdev); int r100_gpu_reset(struct radeon_device *rdev); int r100_mc_init(struct radeon_device *rdev); void r100_mc_fini(struct radeon_device *rdev); +u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc); int r100_wb_init(struct radeon_device *rdev); void r100_wb_fini(struct radeon_device *rdev); int r100_gart_enable(struct radeon_device *rdev); @@ -96,6 +97,7 @@ static struct radeon_asic r100_asic = { .ring_start = &r100_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r100_fence_ring_emit, .cs_parse = &r100_cs_parse, .copy_blit = &r100_copy_blit, @@ -156,6 +158,7 @@ static struct radeon_asic r300_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -196,6 +199,7 @@ static struct radeon_asic r420_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -243,6 +247,7 @@ static struct radeon_asic rs400_asic = { .ring_start = &r300_ring_start, .irq_set = &r100_irq_set, .irq_process = &r100_irq_process, + .get_vblank_counter = &r100_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -266,6 +271,8 @@ void rs600_vram_info(struct radeon_device *rdev); int rs600_mc_init(struct radeon_device *rdev); void rs600_mc_fini(struct radeon_device *rdev); int rs600_irq_set(struct radeon_device *rdev); +int rs600_irq_process(struct radeon_device *rdev); +u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc); int rs600_gart_enable(struct radeon_device *rdev); void rs600_gart_disable(struct radeon_device *rdev); void rs600_gart_tlb_flush(struct radeon_device *rdev); @@ -291,7 +298,8 @@ static struct radeon_asic rs600_asic = { .cp_disable = &r100_cp_disable, .ring_start = &r300_ring_start, .irq_set = &rs600_irq_set, - .irq_process = &r100_irq_process, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -334,7 +342,8 @@ static struct radeon_asic rs690_asic = { .cp_disable = &r100_cp_disable, .ring_start = &r300_ring_start, .irq_set = &rs600_irq_set, - .irq_process = &r100_irq_process, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -382,8 +391,9 @@ static struct radeon_asic rv515_asic = { .cp_fini = &r100_cp_fini, .cp_disable = &r100_cp_disable, .ring_start = &rv515_ring_start, - .irq_set = &r100_irq_set, - .irq_process = &r100_irq_process, + .irq_set = &rs600_irq_set, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, @@ -424,8 +434,9 @@ static struct radeon_asic r520_asic = { .cp_fini = &r100_cp_fini, .cp_disable = &r100_cp_disable, .ring_start = &rv515_ring_start, - .irq_set = &r100_irq_set, - .irq_process = &r100_irq_process, + .irq_set = &rs600_irq_set, + .irq_process = &rs600_irq_process, + .get_vblank_counter = &rs600_get_vblank_counter, .fence_ring_emit = &r300_fence_ring_emit, .cs_parse = &r300_cs_parse, .copy_blit = &r100_copy_blit, diff --git a/drivers/gpu/drm/radeon/radeon_irq_kms.c b/drivers/gpu/drm/radeon/radeon_irq_kms.c index 491d569deb0e..9805e4b6ca1b 100644 --- a/drivers/gpu/drm/radeon/radeon_irq_kms.c +++ b/drivers/gpu/drm/radeon/radeon_irq_kms.c @@ -32,60 +32,6 @@ #include "radeon.h" #include "atom.h" -static inline uint32_t r100_irq_ack(struct radeon_device *rdev) -{ - uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); - uint32_t irq_mask = RADEON_SW_INT_TEST; - - if (irqs) { - WREG32(RADEON_GEN_INT_STATUS, irqs); - } - return irqs & irq_mask; -} - -int r100_irq_set(struct radeon_device *rdev) -{ - uint32_t tmp = 0; - - if (rdev->irq.sw_int) { - tmp |= RADEON_SW_INT_ENABLE; - } - /* Todo go through CRTC and enable vblank int or not */ - WREG32(RADEON_GEN_INT_CNTL, tmp); - return 0; -} - -int r100_irq_process(struct radeon_device *rdev) -{ - uint32_t status; - - status = r100_irq_ack(rdev); - if (!status) { - return IRQ_NONE; - } - while (status) { - /* SW interrupt */ - if (status & RADEON_SW_INT_TEST) { - radeon_fence_process(rdev); - } - status = r100_irq_ack(rdev); - } - return IRQ_HANDLED; -} - -int rs600_irq_set(struct radeon_device *rdev) -{ - uint32_t tmp = 0; - - if (rdev->irq.sw_int) { - tmp |= RADEON_SW_INT_ENABLE; - } - WREG32(RADEON_GEN_INT_CNTL, tmp); - /* Todo go through CRTC and enable vblank int or not */ - WREG32(R500_DxMODE_INT_MASK, 0); - return 0; -} - irqreturn_t radeon_driver_irq_handler_kms(DRM_IRQ_ARGS) { struct drm_device *dev = (struct drm_device *) arg; diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c index 3357110e30ce..d2764bf6b2a2 100644 --- a/drivers/gpu/drm/radeon/radeon_kms.c +++ b/drivers/gpu/drm/radeon/radeon_kms.c @@ -141,19 +141,42 @@ void radeon_driver_preclose_kms(struct drm_device *dev, */ u32 radeon_get_vblank_counter_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ - return 0; + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return -EINVAL; + } + + return radeon_get_vblank_counter(rdev, crtc); } int radeon_enable_vblank_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ - return 0; + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return -EINVAL; + } + + rdev->irq.crtc_vblank_int[crtc] = true; + + return radeon_irq_set(rdev); } void radeon_disable_vblank_kms(struct drm_device *dev, int crtc) { - /* FIXME: implement */ + struct radeon_device *rdev = dev->dev_private; + + if (crtc < 0 || crtc > 1) { + DRM_ERROR("Invalid crtc %d\n", crtc); + return; + } + + rdev->irq.crtc_vblank_int[crtc] = false; + + radeon_irq_set(rdev); } diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c index 7d06dc98a42a..0da72f18fd3a 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c @@ -310,10 +310,13 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode) RADEON_CRTC_DISP_REQ_EN_B)); WREG32_P(RADEON_CRTC_EXT_CNTL, 0, ~mask); } + drm_vblank_post_modeset(dev, radeon_crtc->crtc_id); + radeon_crtc_load_lut(crtc); break; case DRM_MODE_DPMS_STANDBY: case DRM_MODE_DPMS_SUSPEND: case DRM_MODE_DPMS_OFF: + drm_vblank_pre_modeset(dev, radeon_crtc->crtc_id); if (radeon_crtc->crtc_id) WREG32_P(RADEON_CRTC2_GEN_CNTL, mask, ~mask); else { @@ -323,10 +326,6 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode) } break; } - - if (mode != DRM_MODE_DPMS_OFF) { - radeon_crtc_load_lut(crtc); - } } /* properly set crtc bpp when using atombios */ diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h index e1b618574461..5a098f304edb 100644 --- a/drivers/gpu/drm/radeon/radeon_reg.h +++ b/drivers/gpu/drm/radeon/radeon_reg.h @@ -982,12 +982,15 @@ # define RS400_TMDS2_PLLRST (1 << 1) #define RADEON_GEN_INT_CNTL 0x0040 +# define RADEON_CRTC_VBLANK_MASK (1 << 0) +# define RADEON_CRTC2_VBLANK_MASK (1 << 9) # define RADEON_SW_INT_ENABLE (1 << 25) #define RADEON_GEN_INT_STATUS 0x0044 -# define RADEON_VSYNC_INT_AK (1 << 2) -# define RADEON_VSYNC_INT (1 << 2) -# define RADEON_VSYNC2_INT_AK (1 << 6) -# define RADEON_VSYNC2_INT (1 << 6) +# define AVIVO_DISPLAY_INT_STATUS (1 << 0) +# define RADEON_CRTC_VBLANK_STAT (1 << 0) +# define RADEON_CRTC_VBLANK_STAT_ACK (1 << 0) +# define RADEON_CRTC2_VBLANK_STAT (1 << 9) +# define RADEON_CRTC2_VBLANK_STAT_ACK (1 << 9) # define RADEON_SW_INT_FIRE (1 << 26) # define RADEON_SW_INT_TEST (1 << 25) # define RADEON_SW_INT_TEST_ACK (1 << 25) diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c index bbea6dee4a94..7e8ce983a908 100644 --- a/drivers/gpu/drm/radeon/rs600.c +++ b/drivers/gpu/drm/radeon/rs600.c @@ -239,6 +239,88 @@ void rs600_mc_fini(struct radeon_device *rdev) } +/* + * Interrupts + */ +int rs600_irq_set(struct radeon_device *rdev) +{ + uint32_t tmp = 0; + uint32_t mode_int = 0; + + if (rdev->irq.sw_int) { + tmp |= RADEON_SW_INT_ENABLE; + } + if (rdev->irq.crtc_vblank_int[0]) { + tmp |= AVIVO_DISPLAY_INT_STATUS; + mode_int |= AVIVO_D1MODE_INT_MASK; + } + if (rdev->irq.crtc_vblank_int[1]) { + tmp |= AVIVO_DISPLAY_INT_STATUS; + mode_int |= AVIVO_D2MODE_INT_MASK; + } + WREG32(RADEON_GEN_INT_CNTL, tmp); + WREG32(AVIVO_DxMODE_INT_MASK, mode_int); + return 0; +} + +static inline uint32_t rs600_irq_ack(struct radeon_device *rdev, u32 *r500_disp_int) +{ + uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS); + uint32_t irq_mask = RADEON_SW_INT_TEST; + + if (irqs & AVIVO_DISPLAY_INT_STATUS) { + *r500_disp_int = RREG32(AVIVO_DISP_INTERRUPT_STATUS); + if (*r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) { + WREG32(AVIVO_D1MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK); + } + if (*r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) { + WREG32(AVIVO_D2MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK); + } + } else { + *r500_disp_int = 0; + } + + if (irqs) { + WREG32(RADEON_GEN_INT_STATUS, irqs); + } + return irqs & irq_mask; +} + +int rs600_irq_process(struct radeon_device *rdev) +{ + uint32_t status; + uint32_t r500_disp_int; + + status = rs600_irq_ack(rdev, &r500_disp_int); + if (!status && !r500_disp_int) { + return IRQ_NONE; + } + while (status || r500_disp_int) { + /* SW interrupt */ + if (status & RADEON_SW_INT_TEST) { + radeon_fence_process(rdev); + } + /* Vertical blank interrupts */ + if (r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) { + drm_handle_vblank(rdev->ddev, 0); + } + if (r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) { + drm_handle_vblank(rdev->ddev, 1); + } + status = rs600_irq_ack(rdev, &r500_disp_int); + } + return IRQ_HANDLED; +} + +u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc) +{ + if (crtc == 0) + return RREG32(AVIVO_D1CRTC_FRAME_COUNT); + else + return RREG32(AVIVO_D2CRTC_FRAME_COUNT); +} + + /* * Global GPU functions */ -- cgit v1.2.3 From de1b28989edff519d0548ebaa3f94fd3d1524cf2 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Wed, 12 Aug 2009 18:43:14 +1000 Subject: drm/radeon/kms: cut down indirects in register accesses. We really don't want to be doing all these indirects, updating the GPU gart table is something we do often so the less overhead the better. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/r100.c | 20 ------------- drivers/gpu/drm/radeon/r300.c | 23 +-------------- drivers/gpu/drm/radeon/radeon.h | 51 ++++++++++++++++++++++++++++------ drivers/gpu/drm/radeon/radeon_device.c | 13 ++------- drivers/gpu/drm/radeon/rv515.c | 19 ------------- 5 files changed, 47 insertions(+), 79 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c index e1a6e82b9960..90ff8e0ac04e 100644 --- a/drivers/gpu/drm/radeon/r100.c +++ b/drivers/gpu/drm/radeon/r100.c @@ -1622,26 +1622,6 @@ void r100_pll_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) r100_pll_errata_after_data(rdev); } -uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg) -{ - if (reg < 0x10000) - return readl(((void __iomem *)rdev->rmmio) + reg); - else { - writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); - return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); - } -} - -void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - if (reg < 0x10000) - writel(v, ((void __iomem *)rdev->rmmio) + reg); - else { - writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); - writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); - } -} - int r100_init(struct radeon_device *rdev) { return 0; diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c index 8594486e1625..c47579dcafa1 100644 --- a/drivers/gpu/drm/radeon/r300.c +++ b/drivers/gpu/drm/radeon/r300.c @@ -83,8 +83,8 @@ void rv370_pcie_gart_tlb_flush(struct radeon_device *rdev) WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp | RADEON_PCIE_TX_GART_INVALIDATE_TLB); (void)RREG32_PCIE(RADEON_PCIE_TX_GART_CNTL); WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp); - mb(); } + mb(); } int rv370_pcie_gart_enable(struct radeon_device *rdev) @@ -592,27 +592,6 @@ void r300_vram_info(struct radeon_device *rdev) } -/* - * Indirect registers accessor - */ -uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg) -{ - uint32_t r; - - WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff)); - (void)RREG32(RADEON_PCIE_INDEX); - r = RREG32(RADEON_PCIE_DATA); - return r; -} - -void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff)); - (void)RREG32(RADEON_PCIE_INDEX); - WREG32(RADEON_PCIE_DATA, (v)); - (void)RREG32(RADEON_PCIE_DATA); -} - /* * PCIE Lanes */ diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 346112740846..87170a56e37b 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -667,14 +667,11 @@ struct radeon_device { resource_size_t rmmio_base; resource_size_t rmmio_size; void *rmmio; - radeon_rreg_t mm_rreg; - radeon_wreg_t mm_wreg; radeon_rreg_t mc_rreg; radeon_wreg_t mc_wreg; radeon_rreg_t pll_rreg; radeon_wreg_t pll_wreg; - radeon_rreg_t pcie_rreg; - radeon_wreg_t pcie_wreg; + uint32_t pcie_reg_mask; radeon_rreg_t pciep_rreg; radeon_wreg_t pciep_wreg; struct radeon_clock clock; @@ -706,22 +703,42 @@ int radeon_device_init(struct radeon_device *rdev, void radeon_device_fini(struct radeon_device *rdev); int radeon_gpu_wait_for_idle(struct radeon_device *rdev); +static inline uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg) +{ + if (reg < 0x10000) + return readl(((void __iomem *)rdev->rmmio) + reg); + else { + writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); + return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); + } +} + +static inline void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) +{ + if (reg < 0x10000) + writel(v, ((void __iomem *)rdev->rmmio) + reg); + else { + writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX); + writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA); + } +} + /* * Registers read & write functions. */ #define RREG8(reg) readb(((void __iomem *)rdev->rmmio) + (reg)) #define WREG8(reg, v) writeb(v, ((void __iomem *)rdev->rmmio) + (reg)) -#define RREG32(reg) rdev->mm_rreg(rdev, (reg)) -#define WREG32(reg, v) rdev->mm_wreg(rdev, (reg), (v)) +#define RREG32(reg) r100_mm_rreg(rdev, (reg)) +#define WREG32(reg, v) r100_mm_wreg(rdev, (reg), (v)) #define REG_SET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK) #define REG_GET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK) #define RREG32_PLL(reg) rdev->pll_rreg(rdev, (reg)) #define WREG32_PLL(reg, v) rdev->pll_wreg(rdev, (reg), (v)) #define RREG32_MC(reg) rdev->mc_rreg(rdev, (reg)) #define WREG32_MC(reg, v) rdev->mc_wreg(rdev, (reg), (v)) -#define RREG32_PCIE(reg) rdev->pcie_rreg(rdev, (reg)) -#define WREG32_PCIE(reg, v) rdev->pcie_wreg(rdev, (reg), (v)) +#define RREG32_PCIE(reg) rv370_pcie_rreg(rdev, (reg)) +#define WREG32_PCIE(reg, v) rv370_pcie_wreg(rdev, (reg), (v)) #define WREG32_P(reg, val, mask) \ do { \ uint32_t tmp_ = RREG32(reg); \ @@ -737,6 +754,24 @@ int radeon_gpu_wait_for_idle(struct radeon_device *rdev); WREG32_PLL(reg, tmp_); \ } while (0) +/* + * Indirect registers accessor + */ +static inline uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg) +{ + uint32_t r; + + WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask)); + r = RREG32(RADEON_PCIE_DATA); + return r; +} + +static inline void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) +{ + WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask)); + WREG32(RADEON_PCIE_DATA, (v)); +} + void r100_pll_errata_after_index(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c index 9ff6dcb97f9d..7693f7c67bd3 100644 --- a/drivers/gpu/drm/radeon/radeon_device.c +++ b/drivers/gpu/drm/radeon/radeon_device.c @@ -225,25 +225,18 @@ void radeon_invalid_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) void radeon_register_accessor_init(struct radeon_device *rdev) { - rdev->mm_rreg = &r100_mm_rreg; - rdev->mm_wreg = &r100_mm_wreg; rdev->mc_rreg = &radeon_invalid_rreg; rdev->mc_wreg = &radeon_invalid_wreg; rdev->pll_rreg = &radeon_invalid_rreg; rdev->pll_wreg = &radeon_invalid_wreg; - rdev->pcie_rreg = &radeon_invalid_rreg; - rdev->pcie_wreg = &radeon_invalid_wreg; rdev->pciep_rreg = &radeon_invalid_rreg; rdev->pciep_wreg = &radeon_invalid_wreg; /* Don't change order as we are overridding accessor. */ if (rdev->family < CHIP_RV515) { - rdev->pcie_rreg = &rv370_pcie_rreg; - rdev->pcie_wreg = &rv370_pcie_wreg; - } - if (rdev->family >= CHIP_RV515) { - rdev->pcie_rreg = &rv515_pcie_rreg; - rdev->pcie_wreg = &rv515_pcie_wreg; + rdev->pcie_reg_mask = 0xff; + } else { + rdev->pcie_reg_mask = 0x7ff; } /* FIXME: not sure here */ if (rdev->family <= CHIP_R580) { diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c index fd8f3ca716ea..31a7f668ae5a 100644 --- a/drivers/gpu/drm/radeon/rv515.c +++ b/drivers/gpu/drm/radeon/rv515.c @@ -400,25 +400,6 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) WREG32(MC_IND_INDEX, 0); } -uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg) -{ - uint32_t r; - - WREG32(PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(PCIE_INDEX); - r = RREG32(PCIE_DATA); - return r; -} - -void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v) -{ - WREG32(PCIE_INDEX, ((reg) & 0x7ff)); - (void)RREG32(PCIE_INDEX); - WREG32(PCIE_DATA, (v)); - (void)RREG32(PCIE_DATA); -} - - /* * Debugfs info */ -- cgit v1.2.3 From 64c6460875957502541a4ba30835ac625a0bee79 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:43 +0000 Subject: cnic: Fix symbol_put_addr() panic on ia64. When the cnic driver tries to grab a symbol from bnx2 when bnx2 is running init code, symbol_get() will succeed but symbol_put_addr() will hit BUG() a moment later. module_text_address() fails because bnx2 is still in init code. This is fixed by using symbol_put() instead which does the exact opposite of symbol_get(). Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/cnic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4869d77cbe91..ecde186fccd6 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -2543,7 +2543,7 @@ static struct cnic_dev *init_bnx2_cnic(struct net_device *dev) probe = symbol_get(bnx2_cnic_probe); if (probe) { ethdev = (*probe)(dev); - symbol_put_addr(probe); + symbol_put(bnx2_cnic_probe); } if (!ethdev) return NULL; -- cgit v1.2.3 From a3059b12adae868c42629ecf058a94195ef1e958 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:44 +0000 Subject: cnic: Refine registration with bnx2. Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN events. This simplifies the sequence of events and allows locking fixes in the next patch. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 49 ++++++++++++++++++++++++++++++++++++------------- 1 file changed, 36 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index ecde186fccd6..2db81f0e4f72 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -2393,21 +2393,45 @@ static int cnic_start_bnx2_hw(struct cnic_dev *dev) return 0; } -static int cnic_start_hw(struct cnic_dev *dev) +static int cnic_register_netdev(struct cnic_dev *dev) { struct cnic_local *cp = dev->cnic_priv; struct cnic_eth_dev *ethdev = cp->ethdev; int err; - if (test_bit(CNIC_F_CNIC_UP, &dev->flags)) - return -EALREADY; + if (!ethdev) + return -ENODEV; + + if (ethdev->drv_state & CNIC_DRV_STATE_REGD) + return 0; err = ethdev->drv_register_cnic(dev->netdev, cp->cnic_ops, dev); - if (err) { + if (err) printk(KERN_ERR PFX "%s: register_cnic failed\n", dev->netdev->name); - goto err2; - } + + return err; +} + +static void cnic_unregister_netdev(struct cnic_dev *dev) +{ + struct cnic_local *cp = dev->cnic_priv; + struct cnic_eth_dev *ethdev = cp->ethdev; + + if (!ethdev) + return; + + ethdev->drv_unregister_cnic(dev->netdev); +} + +static int cnic_start_hw(struct cnic_dev *dev) +{ + struct cnic_local *cp = dev->cnic_priv; + struct cnic_eth_dev *ethdev = cp->ethdev; + int err; + + if (test_bit(CNIC_F_CNIC_UP, &dev->flags)) + return -EALREADY; dev->regview = ethdev->io_base; cp->chip_id = ethdev->chip_id; @@ -2438,18 +2462,13 @@ static int cnic_start_hw(struct cnic_dev *dev) return 0; err1: - ethdev->drv_unregister_cnic(dev->netdev); cp->free_resc(dev); pci_dev_put(dev->pcidev); -err2: return err; } static void cnic_stop_bnx2_hw(struct cnic_dev *dev) { - struct cnic_local *cp = dev->cnic_priv; - struct cnic_eth_dev *ethdev = cp->ethdev; - cnic_disable_bnx2_int_sync(dev); cnic_reg_wr_ind(dev, BNX2_CP_SCRATCH + 0x20, 0); @@ -2461,8 +2480,6 @@ static void cnic_stop_bnx2_hw(struct cnic_dev *dev) cnic_setup_5709_context(dev, 0); cnic_free_irq(dev); - ethdev->drv_unregister_cnic(dev->netdev); - cnic_free_resc(dev); } @@ -2646,6 +2663,10 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, else if (event == NETDEV_UNREGISTER) cnic_ulp_exit(dev); else if (event == NETDEV_UP) { + if (cnic_register_netdev(dev) != 0) { + cnic_put(dev); + goto done; + } mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); @@ -2672,6 +2693,7 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, cnic_ulp_stop(dev); cnic_stop_hw(dev); mutex_unlock(&cnic_lock); + cnic_unregister_netdev(dev); } else if (event == NETDEV_UNREGISTER) { write_lock(&cnic_dev_lock); list_del_init(&dev->list); @@ -2703,6 +2725,7 @@ static void cnic_release(void) } cnic_ulp_exit(dev); + cnic_unregister_netdev(dev); list_del_init(&dev->list); cnic_free_dev(dev); } -- cgit v1.2.3 From c5a889508203446c1abc1d670599b3a816841813 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:45 +0000 Subject: bnx2: Use mutex on slow path cnic calls. The slow path calls to the cnic driver are sleepable calls so we cannot use rcu_read_lock(). Use mutex for these slow path calls instead. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/bnx2.c | 17 +++++++++++------ drivers/net/bnx2.h | 1 + 2 files changed, 12 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index b70cc99962fc..06b901152d44 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -399,9 +399,11 @@ static int bnx2_unregister_cnic(struct net_device *dev) struct bnx2_napi *bnapi = &bp->bnx2_napi[0]; struct cnic_eth_dev *cp = &bp->cnic_eth_dev; + mutex_lock(&bp->cnic_lock); cp->drv_state = 0; bnapi->cnic_present = 0; rcu_assign_pointer(bp->cnic_ops, NULL); + mutex_unlock(&bp->cnic_lock); synchronize_rcu(); return 0; } @@ -429,13 +431,13 @@ bnx2_cnic_stop(struct bnx2 *bp) struct cnic_ops *c_ops; struct cnic_ctl_info info; - rcu_read_lock(); - c_ops = rcu_dereference(bp->cnic_ops); + mutex_lock(&bp->cnic_lock); + c_ops = bp->cnic_ops; if (c_ops) { info.cmd = CNIC_CTL_STOP_CMD; c_ops->cnic_ctl(bp->cnic_data, &info); } - rcu_read_unlock(); + mutex_unlock(&bp->cnic_lock); } static void @@ -444,8 +446,8 @@ bnx2_cnic_start(struct bnx2 *bp) struct cnic_ops *c_ops; struct cnic_ctl_info info; - rcu_read_lock(); - c_ops = rcu_dereference(bp->cnic_ops); + mutex_lock(&bp->cnic_lock); + c_ops = bp->cnic_ops; if (c_ops) { if (!(bp->flags & BNX2_FLAG_USING_MSIX)) { struct bnx2_napi *bnapi = &bp->bnx2_napi[0]; @@ -455,7 +457,7 @@ bnx2_cnic_start(struct bnx2 *bp) info.cmd = CNIC_CTL_START_CMD; c_ops->cnic_ctl(bp->cnic_data, &info); } - rcu_read_unlock(); + mutex_unlock(&bp->cnic_lock); } #else @@ -7663,6 +7665,9 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev) spin_lock_init(&bp->phy_lock); spin_lock_init(&bp->indirect_lock); +#ifdef BCM_CNIC + mutex_init(&bp->cnic_lock); +#endif INIT_WORK(&bp->reset_task, bnx2_reset_task); dev->base_addr = dev->mem_start = pci_resource_start(pdev, 0); diff --git a/drivers/net/bnx2.h b/drivers/net/bnx2.h index f1edfaa9e56a..a4f12fd0ecd2 100644 --- a/drivers/net/bnx2.h +++ b/drivers/net/bnx2.h @@ -6902,6 +6902,7 @@ struct bnx2 { u32 idle_chk_status_idx; #ifdef BCM_CNIC + struct mutex cnic_lock; struct cnic_eth_dev cnic_eth_dev; #endif -- cgit v1.2.3 From 681dbd710779e8b8d5bae926f6b11f30df70638b Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:46 +0000 Subject: cnic: Fix locking in start/stop calls. The slow path ulp_start and ulp_stop calls to the bnx2i driver are sleepable calls and therefore should not be protected using rcu_read_lock. Fix it by using mutex and setting a bit during these calls. cnic_unregister_device() will now wait for the bit to clear before completing the call. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 44 ++++++++++++++++++++++++++++---------------- drivers/net/cnic.h | 1 + 2 files changed, 29 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 2db81f0e4f72..4ff618a7afd2 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -466,6 +466,7 @@ EXPORT_SYMBOL(cnic_register_driver); static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type) { struct cnic_local *cp = dev->cnic_priv; + int i = 0; if (ulp_type >= MAX_CNIC_ULP_TYPE) { printk(KERN_ERR PFX "cnic_unregister_device: Bad type %d\n", @@ -486,6 +487,15 @@ static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type) synchronize_rcu(); + while (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type]) && + i < 20) { + msleep(100); + i++; + } + if (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type])) + printk(KERN_WARNING PFX "%s: Failed waiting for ULP up call" + " to complete.\n", dev->netdev->name); + return 0; } EXPORT_SYMBOL(cnic_unregister_driver); @@ -1076,18 +1086,23 @@ static void cnic_ulp_stop(struct cnic_dev *dev) if (cp->cnic_uinfo) cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL); - rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cp->ulp_ops[if_type]); - if (!ulp_ops) + mutex_lock(&cnic_lock); + ulp_ops = cp->ulp_ops[if_type]; + if (!ulp_ops) { + mutex_unlock(&cnic_lock); continue; + } + set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); + mutex_unlock(&cnic_lock); if (test_and_clear_bit(ULP_F_START, &cp->ulp_flags[if_type])) ulp_ops->cnic_stop(cp->ulp_handle[if_type]); + + clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); } - rcu_read_unlock(); } static void cnic_ulp_start(struct cnic_dev *dev) @@ -1095,18 +1110,23 @@ static void cnic_ulp_start(struct cnic_dev *dev) struct cnic_local *cp = dev->cnic_priv; int if_type; - rcu_read_lock(); for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cp->ulp_ops[if_type]); - if (!ulp_ops || !ulp_ops->cnic_start) + mutex_lock(&cnic_lock); + ulp_ops = cp->ulp_ops[if_type]; + if (!ulp_ops || !ulp_ops->cnic_start) { + mutex_unlock(&cnic_lock); continue; + } + set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); + mutex_unlock(&cnic_lock); if (!test_and_set_bit(ULP_F_START, &cp->ulp_flags[if_type])) ulp_ops->cnic_start(cp->ulp_handle[if_type]); + + clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]); } - rcu_read_unlock(); } static int cnic_ctl(void *data, struct cnic_ctl_info *info) @@ -1116,22 +1136,18 @@ static int cnic_ctl(void *data, struct cnic_ctl_info *info) switch (info->cmd) { case CNIC_CTL_STOP_CMD: cnic_hold(dev); - mutex_lock(&cnic_lock); cnic_ulp_stop(dev); cnic_stop_hw(dev); - mutex_unlock(&cnic_lock); cnic_put(dev); break; case CNIC_CTL_START_CMD: cnic_hold(dev); - mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); - mutex_unlock(&cnic_lock); cnic_put(dev); break; default: @@ -2667,10 +2683,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, cnic_put(dev); goto done; } - mutex_lock(&cnic_lock); if (!cnic_start_hw(dev)) cnic_ulp_start(dev); - mutex_unlock(&cnic_lock); } rcu_read_lock(); @@ -2689,10 +2703,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event, rcu_read_unlock(); if (event == NETDEV_GOING_DOWN) { - mutex_lock(&cnic_lock); cnic_ulp_stop(dev); cnic_stop_hw(dev); - mutex_unlock(&cnic_lock); cnic_unregister_netdev(dev); } else if (event == NETDEV_UNREGISTER) { write_lock(&cnic_dev_lock); diff --git a/drivers/net/cnic.h b/drivers/net/cnic.h index 5192d4a9df5a..a94b302bb464 100644 --- a/drivers/net/cnic.h +++ b/drivers/net/cnic.h @@ -176,6 +176,7 @@ struct cnic_local { unsigned long ulp_flags[MAX_CNIC_ULP_TYPE]; #define ULP_F_INIT 0 #define ULP_F_START 1 +#define ULP_F_CALL_PENDING 2 struct cnic_ulp_ops *ulp_ops[MAX_CNIC_ULP_TYPE]; /* protected by ulp_lock */ -- cgit v1.2.3 From 7fc1ece40704b150477e548a7a98d285cc418790 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 14 Aug 2009 15:49:47 +0000 Subject: cnic: Fix locking in init/exit calls. The slow path ulp_init and ulp_exit calls to the bnx2i driver are sleepable calls and therefore should not be protected using rcu_read_lock. Fix it by using mutex and refcount during these calls. cnic_unregister_driver() will now wait for the refcount to go to zero before completing the call. Signed-off-by: Michael Chan Reviewed-by: Benjamin Li Signed-off-by: David S. Miller --- drivers/net/cnic.c | 48 +++++++++++++++++++++++++++++++++++++++--------- drivers/net/cnic_if.h | 1 + 2 files changed, 40 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index 4ff618a7afd2..74c342959b7b 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -138,6 +138,16 @@ static struct cnic_dev *cnic_from_netdev(struct net_device *netdev) return NULL; } +static inline void ulp_get(struct cnic_ulp_ops *ulp_ops) +{ + atomic_inc(&ulp_ops->ref_count); +} + +static inline void ulp_put(struct cnic_ulp_ops *ulp_ops) +{ + atomic_dec(&ulp_ops->ref_count); +} + static void cnic_ctx_wr(struct cnic_dev *dev, u32 cid_addr, u32 off, u32 val) { struct cnic_local *cp = dev->cnic_priv; @@ -358,6 +368,7 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) } read_unlock(&cnic_dev_lock); + atomic_set(&ulp_ops->ref_count, 0); rcu_assign_pointer(cnic_ulp_tbl[ulp_type], ulp_ops); mutex_unlock(&cnic_lock); @@ -379,6 +390,8 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops) int cnic_unregister_driver(int ulp_type) { struct cnic_dev *dev; + struct cnic_ulp_ops *ulp_ops; + int i = 0; if (ulp_type >= MAX_CNIC_ULP_TYPE) { printk(KERN_ERR PFX "cnic_unregister_driver: Bad type %d\n", @@ -386,7 +399,8 @@ int cnic_unregister_driver(int ulp_type) return -EINVAL; } mutex_lock(&cnic_lock); - if (!cnic_ulp_tbl[ulp_type]) { + ulp_ops = cnic_ulp_tbl[ulp_type]; + if (!ulp_ops) { printk(KERN_ERR PFX "cnic_unregister_driver: Type %d has not " "been registered\n", ulp_type); goto out_unlock; @@ -411,6 +425,14 @@ int cnic_unregister_driver(int ulp_type) mutex_unlock(&cnic_lock); synchronize_rcu(); + while ((atomic_read(&ulp_ops->ref_count) != 0) && (i < 20)) { + msleep(100); + i++; + } + + if (atomic_read(&ulp_ops->ref_count) != 0) + printk(KERN_WARNING PFX "%s: Failed waiting for ref count to go" + " to zero.\n", dev->netdev->name); return 0; out_unlock: @@ -1161,19 +1183,23 @@ static void cnic_ulp_init(struct cnic_dev *dev) int i; struct cnic_local *cp = dev->cnic_priv; - rcu_read_lock(); for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cnic_ulp_tbl[i]); - if (!ulp_ops || !ulp_ops->cnic_init) + mutex_lock(&cnic_lock); + ulp_ops = cnic_ulp_tbl[i]; + if (!ulp_ops || !ulp_ops->cnic_init) { + mutex_unlock(&cnic_lock); continue; + } + ulp_get(ulp_ops); + mutex_unlock(&cnic_lock); if (!test_and_set_bit(ULP_F_INIT, &cp->ulp_flags[i])) ulp_ops->cnic_init(dev); + ulp_put(ulp_ops); } - rcu_read_unlock(); } static void cnic_ulp_exit(struct cnic_dev *dev) @@ -1181,19 +1207,23 @@ static void cnic_ulp_exit(struct cnic_dev *dev) int i; struct cnic_local *cp = dev->cnic_priv; - rcu_read_lock(); for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) { struct cnic_ulp_ops *ulp_ops; - ulp_ops = rcu_dereference(cnic_ulp_tbl[i]); - if (!ulp_ops || !ulp_ops->cnic_exit) + mutex_lock(&cnic_lock); + ulp_ops = cnic_ulp_tbl[i]; + if (!ulp_ops || !ulp_ops->cnic_exit) { + mutex_unlock(&cnic_lock); continue; + } + ulp_get(ulp_ops); + mutex_unlock(&cnic_lock); if (test_and_clear_bit(ULP_F_INIT, &cp->ulp_flags[i])) ulp_ops->cnic_exit(dev); + ulp_put(ulp_ops); } - rcu_read_unlock(); } static int cnic_cm_offload_pg(struct cnic_sock *csk) diff --git a/drivers/net/cnic_if.h b/drivers/net/cnic_if.h index d1bce27ee99e..a49235739eef 100644 --- a/drivers/net/cnic_if.h +++ b/drivers/net/cnic_if.h @@ -290,6 +290,7 @@ struct cnic_ulp_ops { void (*iscsi_nl_send_msg)(struct cnic_dev *dev, u32 msg_type, char *data, u16 data_size); struct module *owner; + atomic_t ref_count; }; extern int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops); -- cgit v1.2.3 From 82776a4bcd7aa5fbcd2e6339b3ce88b727dd40ab Mon Sep 17 00:00:00 2001 From: Bruce Allan Date: Fri, 14 Aug 2009 14:35:33 +0000 Subject: e1000e: WoL does not work on 82577/82578 with manageability enabled With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get configured on newer parts which use PHY wakeup vs. MAC wakeup which causes WoL to not work. The driver should configure PHY wakeup whether or not manageability is enabled. Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/netdev.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 63415bb6f48f..58e22fcb22b5 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -4538,8 +4538,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) /* Allow time for pending master requests to run */ e1000e_disable_pcie_master(&adapter->hw); - if ((adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) && - !(hw->mac.ops.check_mng_mode(hw))) { + if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { /* enable wakeup by the PHY */ retval = e1000_init_phy_wakeup(adapter, wufc); if (retval) @@ -4557,7 +4556,8 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) *enable_wake = !!wufc; /* make sure adapter isn't asleep if manageability is enabled */ - if (adapter->flags & FLAG_MNG_PT_ENABLED) + if ((adapter->flags & FLAG_MNG_PT_ENABLED) || + (hw->mac.ops.check_mng_mode(hw))) *enable_wake = true; if (adapter->hw.phy.type == e1000_phy_igp_3) -- cgit v1.2.3 From 68eac4602b9104cdaa6c18b3edd914cececa6a1e Mon Sep 17 00:00:00 2001 From: Xiaotian Feng Date: Fri, 14 Aug 2009 14:35:52 +0000 Subject: e1000e: fix use of pci_enable_pcie_error_reporting commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer support for e1000e, but it is not reasonable to disable it in e1000_remove but enable it in e1000_resume. This patch enables aer support in e1000_probe. Signed-off-by: Xiaotian Feng Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000e/netdev.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 58e22fcb22b5..fa92a683aefd 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -4670,14 +4670,6 @@ static int e1000_resume(struct pci_dev *pdev) return err; } - /* AER (Advanced Error Reporting) hooks */ - err = pci_enable_pcie_error_reporting(pdev); - if (err) { - dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed " - "0x%x\n", err); - /* non-fatal, continue */ - } - pci_set_master(pdev); pci_enable_wake(pdev, PCI_D3hot, 0); @@ -4990,6 +4982,14 @@ static int __devinit e1000_probe(struct pci_dev *pdev, if (err) goto err_pci_reg; + /* AER (Advanced Error Reporting) hooks */ + err = pci_enable_pcie_error_reporting(pdev); + if (err) { + dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed " + "0x%x\n", err); + /* non-fatal, continue */ + } + pci_set_master(pdev); /* PCI config space info */ err = pci_save_state(pdev); -- cgit v1.2.3 From 894ef820b10d77e2d6d717342fc408bdd9825139 Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sun, 16 Aug 2009 07:33:30 -0700 Subject: dm-log-userspace: fix printk format warning drivers/md/dm-log-userspace-transfer.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t' Previously posted and acked, but apparently lost. http://lkml.indiana.edu/hypermail/linux/kernel/0906.2/02074.html Signed-off-by: Randy Dunlap Cc: dm-devel@redhat.com Signed-off-by: Linus Torvalds --- drivers/md/dm-log-userspace-transfer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/md/dm-log-userspace-transfer.c b/drivers/md/dm-log-userspace-transfer.c index 0ca1ee768a1f..8ce74d95ae4d 100644 --- a/drivers/md/dm-log-userspace-transfer.c +++ b/drivers/md/dm-log-userspace-transfer.c @@ -108,7 +108,7 @@ static int fill_pkg(struct cn_msg *msg, struct dm_ulog_request *tfr) *(pkg->data_size) = 0; } else if (tfr->data_size > *(pkg->data_size)) { DMERR("Insufficient space to receive package [%u] " - "(%u vs %lu)", tfr->request_type, + "(%u vs %zu)", tfr->request_type, tfr->data_size, *(pkg->data_size)); *(pkg->data_size) = 0; -- cgit v1.2.3 From cefb87efc9aa0288849149484870d5ab989fbd59 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Sun, 16 Aug 2009 21:05:45 +1000 Subject: drm/radeon/kms: implement bo busy check + current domain This implements the busy ioctl along with a current domain check. returns 0 or -EBUSY puts the current domain no matter what the answer. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon.h | 1 + drivers/gpu/drm/radeon/radeon_gem.c | 22 +++++++++++++++++++++- drivers/gpu/drm/radeon/radeon_object.c | 19 +++++++++++++++++++ include/drm/radeon_drm.h | 2 +- 4 files changed, 42 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h index 87170a56e37b..79ad98264e33 100644 --- a/drivers/gpu/drm/radeon/radeon.h +++ b/drivers/gpu/drm/radeon/radeon.h @@ -242,6 +242,7 @@ int radeon_object_pin(struct radeon_object *robj, uint32_t domain, uint64_t *gpu_addr); void radeon_object_unpin(struct radeon_object *robj); int radeon_object_wait(struct radeon_object *robj); +int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement); int radeon_object_evict_vram(struct radeon_device *rdev); int radeon_object_mmap(struct radeon_object *robj, uint64_t *offset); void radeon_object_force_delete(struct radeon_device *rdev); diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c index cded5180c752..d4ceff13bbb1 100644 --- a/drivers/gpu/drm/radeon/radeon_gem.c +++ b/drivers/gpu/drm/radeon/radeon_gem.c @@ -262,7 +262,27 @@ int radeon_gem_mmap_ioctl(struct drm_device *dev, void *data, int radeon_gem_busy_ioctl(struct drm_device *dev, void *data, struct drm_file *filp) { - /* FIXME: implement */ + struct drm_radeon_gem_busy *args = data; + struct drm_gem_object *gobj; + struct radeon_object *robj; + int r; + uint32_t cur_placement; + + gobj = drm_gem_object_lookup(dev, filp, args->handle); + if (gobj == NULL) { + return -EINVAL; + } + robj = gobj->driver_private; + r = radeon_object_busy_domain(robj, &cur_placement); + if (cur_placement == TTM_PL_VRAM) + args->domain = RADEON_GEM_DOMAIN_VRAM; + if (cur_placement == TTM_PL_FLAG_TT) + args->domain = RADEON_GEM_DOMAIN_GTT; + if (cur_placement == TTM_PL_FLAG_SYSTEM) + args->domain = RADEON_GEM_DOMAIN_CPU; + mutex_lock(&dev->struct_mutex); + drm_gem_object_unreference(gobj); + mutex_unlock(&dev->struct_mutex); return 0; } diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c index e98cae3bf4a6..b85fb83d7ae8 100644 --- a/drivers/gpu/drm/radeon/radeon_object.c +++ b/drivers/gpu/drm/radeon/radeon_object.c @@ -316,6 +316,25 @@ int radeon_object_wait(struct radeon_object *robj) return r; } +int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement) +{ + int r = 0; + + r = radeon_object_reserve(robj, true); + if (unlikely(r != 0)) { + DRM_ERROR("radeon: failed to reserve object for waiting.\n"); + return r; + } + spin_lock(&robj->tobj.lock); + *cur_placement = robj->tobj.mem.mem_type; + if (robj->tobj.sync_obj) { + r = ttm_bo_wait(&robj->tobj, true, true, true); + } + spin_unlock(&robj->tobj.lock); + radeon_object_unreserve(robj); + return r; +} + int radeon_object_evict_vram(struct radeon_device *rdev) { if (rdev->flags & RADEON_IS_IGP) { diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h index af4b4826997e..f81c3232accd 100644 --- a/include/drm/radeon_drm.h +++ b/include/drm/radeon_drm.h @@ -838,7 +838,7 @@ struct drm_radeon_gem_wait_idle { struct drm_radeon_gem_busy { uint32_t handle; - uint32_t busy; + uint32_t domain; }; struct drm_radeon_gem_pread { -- cgit v1.2.3 From 80ffb3cceaefa405f2ecd46d66500ed8d53efe74 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Tue, 18 Aug 2009 10:35:26 +1000 Subject: Fix new incorrect error return from do_md_stop. Recent commit c8c00a6915a2e3d10416e8bdd3138429beb96210 changed the exit paths in do_md_stop and was not quite careful enough. There is one path were 'err' now needs to be cleared but it isn't. So setting an array to readonly (with mdadm --readonly) will work, but will incorrectly report and error: ENXIO. Signed-off-by: NeilBrown --- drivers/md/md.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/md/md.c b/drivers/md/md.c index 103f2d33fa89..9dd872000cec 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -4364,6 +4364,7 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open) if (mode == 1) set_disk_ro(disk, 1); clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery); + err = 0; } out: mutex_unlock(&mddev->open_mutex); -- cgit v1.2.3 From b8978784544e8b4e8fbacb558df8580957d4f8a5 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 18 Aug 2009 14:11:16 -0700 Subject: spi_s3c24xx: fix clock rate calculation Currently the clock rate calculation may round as pleased, which means that it is possible that we will round down and end up with a faster clock rate than intended. Change the calculation to use DIV_ROUND_UP() to ensure that we end up with a clock rate either the same as or lower than the user requested one. Signed-off-by: Ben Dooks Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/spi_s3c24xx.c | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-) (limited to 'drivers') diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c index e0d44af4745a..590be85c8f3d 100644 --- a/drivers/spi/spi_s3c24xx.c +++ b/drivers/spi/spi_s3c24xx.c @@ -111,6 +111,7 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, unsigned int bpw; unsigned int hz; unsigned int div; + unsigned long clk; bpw = t ? t->bits_per_word : spi->bits_per_word; hz = t ? t->speed_hz : spi->max_speed_hz; @@ -120,20 +121,16 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, return -EINVAL; } - div = clk_get_rate(hw->clk) / hz; - - /* is clk = pclk / (2 * (pre+1)), or is it - * clk = (pclk * 2) / ( pre + 1) */ - - div /= 2; - - if (div > 0) - div -= 1; + clk = clk_get_rate(hw->clk); + div = DIV_ROUND_UP(clk, hz * 2) - 1; if (div > 255) div = 255; - dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", div, hz); + dev_dbg(&spi->dev, "setting pre-scaler to %d (wanted %d, got %ld)\n", + div, hz, clk / (2 * (div + 1))); + + writeb(div, hw->regs + S3C2410_SPPRE); spin_lock(&hw->bitbang.lock); -- cgit v1.2.3 From 191529756633052680dd9d23ad63744ca5aa02a1 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Tue, 18 Aug 2009 14:11:17 -0700 Subject: spi_s3c24xx: fix transfer setup code Since the changes to the bitbang driver, there is the possibility we will be called with either the speed_hz or bpw values zero. We take these to mean that the default values (8 bits per word, or maximum bus speed). Signed-off-by: Ben Dooks Cc: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- drivers/spi/spi_s3c24xx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers') diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c index 590be85c8f3d..3f3119d760db 100644 --- a/drivers/spi/spi_s3c24xx.c +++ b/drivers/spi/spi_s3c24xx.c @@ -116,6 +116,12 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi, bpw = t ? t->bits_per_word : spi->bits_per_word; hz = t ? t->speed_hz : spi->max_speed_hz; + if (!bpw) + bpw = 8; + + if (!hz) + hz = spi->max_speed_hz; + if (bpw != 8) { dev_err(&spi->dev, "invalid bits-per-word (%d)\n", bpw); return -EINVAL; -- cgit v1.2.3 From 80e6914db18e702549a15dea36fa7ace17f25c50 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:22:37 +1000 Subject: drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it. LVDS always requests RMX_FULL, we need to fix it so that doesn't happen before we can enable LVDS on crtc 1. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_legacy_encoders.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c index 34d0f58eb944..9322675ef6d0 100644 --- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c +++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c @@ -1066,6 +1066,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t switch (radeon_encoder->encoder_id) { case ENCODER_OBJECT_ID_INTERNAL_LVDS: + encoder->possible_crtcs = 0x1; drm_encoder_init(dev, encoder, &radeon_legacy_lvds_enc_funcs, DRM_MODE_ENCODER_LVDS); drm_encoder_helper_add(encoder, &radeon_legacy_lvds_helper_funcs); if (rdev->is_atom_bios) -- cgit v1.2.3 From bf8e828b00a5b6a0fea16f452be578c060d57d64 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:20:47 +1000 Subject: drm/radeon/kms: memset the allocated framebuffer before using it. This gets rid of some ugliness, we shuold probably find a way for the GPU to zero this. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_fb.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c index 3206c0ad7b6c..ec383edf5f38 100644 --- a/drivers/gpu/drm/radeon/radeon_fb.c +++ b/drivers/gpu/drm/radeon/radeon_fb.c @@ -574,6 +574,8 @@ int radeonfb_create(struct radeon_device *rdev, goto out_unref; } + memset_io(fbptr, 0, aligned_size); + strcpy(info->fix.id, "radeondrmfb"); info->fix.type = FB_TYPE_PACKED_PIXELS; info->fix.visual = FB_VISUAL_TRUECOLOR; -- cgit v1.2.3 From 6a719e05330ef19acd9392dbbfb95a774776dee5 Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 10:19:51 +1000 Subject: drm/kms/radeon: cleanup combios TV table like DDX. The fallback case wasn't getting executed properly if there was no TV table, which my T42 M7 hasn't got. Signed-off-by: Dave Airlie --- drivers/gpu/drm/radeon/radeon_combios.c | 48 +++++++++++++-------------------- 1 file changed, 19 insertions(+), 29 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/radeon/radeon_combios.c b/drivers/gpu/drm/radeon/radeon_combios.c index afc4db280b94..2a027e00762a 100644 --- a/drivers/gpu/drm/radeon/radeon_combios.c +++ b/drivers/gpu/drm/radeon/radeon_combios.c @@ -685,23 +685,15 @@ static const uint32_t default_tvdac_adj[CHIP_LAST] = { 0x00780000, /* rs480 */ }; -static struct radeon_encoder_tv_dac - *radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev) +static void radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev, + struct radeon_encoder_tv_dac *tv_dac) { - struct radeon_encoder_tv_dac *tv_dac = NULL; - - tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); - - if (!tv_dac) - return NULL; - tv_dac->ps2_tvdac_adj = default_tvdac_adj[rdev->family]; if ((rdev->flags & RADEON_IS_MOBILITY) && (rdev->family == CHIP_RV250)) tv_dac->ps2_tvdac_adj = 0x00880000; tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; - - return tv_dac; + return; } struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct @@ -713,19 +705,18 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct uint16_t dac_info; uint8_t rev, bg, dac; struct radeon_encoder_tv_dac *tv_dac = NULL; + int found = 0; + + tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); + if (!tv_dac) + return NULL; if (rdev->bios == NULL) - return radeon_legacy_get_tv_dac_info_from_table(rdev); + goto out; /* first check TV table */ dac_info = combios_get_table_offset(dev, COMBIOS_TV_INFO_TABLE); if (dac_info) { - tv_dac = - kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL); - - if (!tv_dac) - return NULL; - rev = RBIOS8(dac_info + 0x3); if (rev > 4) { bg = RBIOS8(dac_info + 0xc) & 0xf; @@ -739,6 +730,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct bg = RBIOS8(dac_info + 0x10) & 0xf; dac = RBIOS8(dac_info + 0x11) & 0xf; tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20); + found = 1; } else if (rev > 1) { bg = RBIOS8(dac_info + 0xc) & 0xf; dac = (RBIOS8(dac_info + 0xc) >> 4) & 0xf; @@ -751,22 +743,15 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct bg = RBIOS8(dac_info + 0xe) & 0xf; dac = (RBIOS8(dac_info + 0xe) >> 4) & 0xf; tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20); + found = 1; } - tv_dac->tv_std = radeon_combios_get_tv_info(encoder); - - } else { + } + if (!found) { /* then check CRT table */ dac_info = combios_get_table_offset(dev, COMBIOS_CRT_INFO_TABLE); if (dac_info) { - tv_dac = - kzalloc(sizeof(struct radeon_encoder_tv_dac), - GFP_KERNEL); - - if (!tv_dac) - return NULL; - rev = RBIOS8(dac_info) & 0x3; if (rev < 2) { bg = RBIOS8(dac_info + 0x3) & 0xf; @@ -775,6 +760,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct (bg << 16) | (dac << 20); tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; + found = 1; } else { bg = RBIOS8(dac_info + 0x4) & 0xf; dac = RBIOS8(dac_info + 0x5) & 0xf; @@ -782,13 +768,17 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct (bg << 16) | (dac << 20); tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj; tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj; + found = 1; } } else { DRM_INFO("No TV DAC info found in BIOS\n"); - return radeon_legacy_get_tv_dac_info_from_table(rdev); } } +out: + if (!found) /* fallback to defaults */ + radeon_legacy_get_tv_dac_info_from_table(rdev, tv_dac); + return tv_dac; } -- cgit v1.2.3 From 5ef5f72febfea420ce58f670bad83830a5e5e3de Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Mon, 17 Aug 2009 13:11:23 +1000 Subject: drm/kms: teardown crtc correctly when fb is destroyed. If userspace destroys a framebuffer that is in use on a crtc, don't just null it out, tear down the crtc properly so the hw gets turned off. Signed-off-by: Dave Airlie --- drivers/gpu/drm/drm_crtc.c | 40 ++++++++++++---------------------------- 1 file changed, 12 insertions(+), 28 deletions(-) (limited to 'drivers') diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 33be210d6723..2f631c75f704 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -257,31 +257,6 @@ void *drm_mode_object_find(struct drm_device *dev, uint32_t id, uint32_t type) } EXPORT_SYMBOL(drm_mode_object_find); -/** - * drm_crtc_from_fb - find the CRTC structure associated with an fb - * @dev: DRM device - * @fb: framebuffer in question - * - * LOCKING: - * Caller must hold mode_config lock. - * - * Find CRTC in the mode_config structure that matches @fb. - * - * RETURNS: - * Pointer to the CRTC or NULL if it wasn't found. - */ -struct drm_crtc *drm_crtc_from_fb(struct drm_device *dev, - struct drm_framebuffer *fb) -{ - struct drm_crtc *crtc; - - list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - if (crtc->fb == fb) - return crtc; - } - return NULL; -} - /** * drm_framebuffer_init - initialize a framebuffer * @dev: DRM device @@ -328,11 +303,20 @@ void drm_framebuffer_cleanup(struct drm_framebuffer *fb) { struct drm_device *dev = fb->dev; struct drm_crtc *crtc; + struct drm_mode_set set; + int ret; /* remove from any CRTC */ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) { - if (crtc->fb == fb) - crtc->fb = NULL; + if (crtc->fb == fb) { + /* should turn off the crtc */ + memset(&set, 0, sizeof(struct drm_mode_set)); + set.crtc = crtc; + set.fb = NULL; + ret = crtc->funcs->set_config(&set); + if (ret) + DRM_ERROR("failed to reset crtc %p when fb was deleted\n", crtc); + } } drm_mode_object_put(dev, &fb->base); @@ -1511,7 +1495,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, set.mode = mode; set.connectors = connector_set; set.num_connectors = crtc_req->count_connectors; - set.fb =fb; + set.fb = fb; ret = crtc->funcs->set_config(&set); out: -- cgit v1.2.3