From 3e8d6d85adedc59115a564c0a54b36e42087c4d9 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 13 Feb 2014 15:49:17 -0500 Subject: USB: EHCI: add delay during suspend to prevent erroneous wakeups High-speed USB connections revert back to full-speed signalling when the device goes into suspend. This takes several milliseconds, and during that time it's not possible to tell reliably whether the device has been disconnected. On some platforms, the Wake-On-Disconnect circuitry gets confused during this intermediate state. It generates a false wakeup signal, which can prevent the controller from going to sleep. To avoid this problem, this patch adds a 5-ms delay to the ehci_bus_suspend() routine if any ports have to switch over to full-speed signalling. (Actually, the delay was already present for devices using a particular kind of PHY power management; the patch merely causes the delay to be used more widely.) Signed-off-by: Alan Stern Reviewed-by: Peter Chen CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hub.c | 26 ++++++++++++++++++++++---- 1 file changed, 22 insertions(+), 4 deletions(-) (limited to 'drivers/usb/host/ehci-hub.c') diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 47b858fc50b2..7ae0c4d51741 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -238,6 +238,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) int port; int mask; int changed; + bool fs_idle_delay; ehci_dbg(ehci, "suspend root hub\n"); @@ -272,6 +273,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) ehci->bus_suspended = 0; ehci->owned_ports = 0; changed = 0; + fs_idle_delay = false; port = HCS_N_PORTS(ehci->hcs_params); while (port--) { u32 __iomem *reg = &ehci->regs->port_status [port]; @@ -300,16 +302,32 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) } if (t1 != t2) { + /* + * On some controllers, Wake-On-Disconnect will + * generate false wakeup signals until the bus + * switches over to full-speed idle. For their + * sake, add a delay if we need one. + */ + if ((t2 & PORT_WKDISC_E) && + ehci_port_speed(ehci, t2) == + USB_PORT_STAT_HIGH_SPEED) + fs_idle_delay = true; ehci_writel(ehci, t2, reg); changed = 1; } } + spin_unlock_irq(&ehci->lock); + + if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) { + /* + * Wait for HCD to enter low-power mode or for the bus + * to switch to full-speed idle. + */ + usleep_range(5000, 5500); + } if (changed && ehci->has_tdi_phy_lpm) { - spin_unlock_irq(&ehci->lock); - msleep(5); /* 5 ms for HCD to enter low-power mode */ spin_lock_irq(&ehci->lock); - port = HCS_N_PORTS(ehci->hcs_params); while (port--) { u32 __iomem *hostpc_reg = &ehci->regs->hostpc[port]; @@ -322,8 +340,8 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) port, (t3 & HOSTPC_PHCD) ? "succeeded" : "failed"); } + spin_unlock_irq(&ehci->lock); } - spin_unlock_irq(&ehci->lock); /* Apparently some devices need a >= 1-uframe delay here */ if (ehci->bus_suspended) -- cgit v1.2.3