From 2e5f9f281ee8369f56d403b4a52942f19b6978f8 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Fri, 15 Jan 2016 01:55:22 +0100 Subject: net: phy: at803x: Allow specifying the RGMII RX clock delay via phy mode at803x currently automatically enables the RGMII TX clock delay when the phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be done when PHY_INTERFACE_MODE_RGMII_ID is specified. Use a similar logic to enable the RGMII RX clock delay as well. at803x_context_{save,restore} were not touched because these are only used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant). Signed-off-by: Martin Blumenstingl Signed-off-by: David S. Miller --- drivers/net/phy/at803x.c | 63 +++++++++++++++++++++++++++++++++++++++++------- 1 file changed, 54 insertions(+), 9 deletions(-) (limited to 'drivers/net/phy/at803x.c') diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 358944764ba7..333c1bc79929 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -36,8 +36,10 @@ #define AT803X_INSR 0x0013 #define AT803X_DEBUG_ADDR 0x1D #define AT803X_DEBUG_DATA 0x1E -#define AT803X_DEBUG_SYSTEM_MODE_CTRL 0x05 -#define AT803X_DEBUG_RGMII_TX_CLK_DLY BIT(8) +#define AT803X_DEBUG_REG_0 0x00 +#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) +#define AT803X_DEBUG_REG_5 0x05 +#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) #define ATH8030_PHY_ID 0x004dd076 #define ATH8031_PHY_ID 0x004dd074 @@ -61,6 +63,46 @@ struct at803x_context { u16 led_control; }; +static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg) +{ + int ret; + + ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg); + if (ret < 0) + return ret; + + return phy_read(phydev, AT803X_DEBUG_DATA); +} + +static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, + u16 clear, u16 set) +{ + u16 val; + int ret; + + ret = at803x_debug_reg_read(phydev, reg); + if (ret < 0) + return ret; + + val = ret & 0xffff; + val &= ~clear; + val |= set; + + return phy_write(phydev, AT803X_DEBUG_DATA, val); +} + +static inline int at803x_enable_rx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0, + AT803X_DEBUG_RX_CLK_DLY_EN); +} + +static inline int at803x_enable_tx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0, + AT803X_DEBUG_TX_CLK_DLY_EN); +} + /* save relevant PHY registers to private copy */ static void at803x_context_save(struct phy_device *phydev, struct at803x_context *context) @@ -217,14 +259,17 @@ static int at803x_config_init(struct phy_device *phydev) if (ret < 0) return ret; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { - ret = phy_write(phydev, AT803X_DEBUG_ADDR, - AT803X_DEBUG_SYSTEM_MODE_CTRL); - if (ret) + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { + ret = at803x_enable_rx_delay(phydev); + if (ret < 0) return ret; - ret = phy_write(phydev, AT803X_DEBUG_DATA, - AT803X_DEBUG_RGMII_TX_CLK_DLY); - if (ret) + } + + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { + ret = at803x_enable_tx_delay(phydev); + if (ret < 0) return ret; } -- cgit v1.2.3