| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Reimplement ceph_calc_pg_primary() in terms of ceph_calc_pg_acting()
and get rid of the now unused calc_pg_raw().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Respond to non-default primary_affinity values accordingly. (Primary
affinity allows the admin to shift 'primary responsibility' away from
specific osds, effectively shifting around the read side of the
workload and whatever overhead is incurred by peering and writes by
virtue of being the primary).
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Change apply_temp() to override primary in the same way pg_temp
overrides osd set. primary_temp overrides pg_temp primary too.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
In preparation for adding support for primary_temp, stop assuming
primaryness: add a primary out parameter to ceph_calc_pg_acting() and
change call sites accordingly. Primary is now specified separately
from the order of osds in the set.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Switch ceph_calc_pg_acting() to new helpers: pg_to_raw_osds(),
raw_to_up_osds() and apply_temps().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
apply_temp() helper for applying various temporary mappings (at this
point only pg_temp mappings) to the up set, therefore transforming it
into an acting set.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
pg_to_raw_osds() helper for computing a raw (crush) set, which can
contain non-existant and down osds.
raw_to_up_osds() helper for pruning non-existant and down osds from the
raw set, therefore transforming it into an up set, and determining up
primary.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Add two helpers to decode primary_affinity (full map, vector<u32>) and
new_primary_affinity (inc map, map<u32, u32>) and switch to them.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Add primary_affinity infrastructure. primary_affinity values are
stored in an max_osd-sized array, hanging off ceph_osdmap, similar to
a osd_weight array.
Introduce {get,set}_primary_affinity() helpers, primarily to return
CEPH_OSD_DEFAULT_PRIMARY_AFFINITY when no affinity has been set and to
abstract out osd_primary_affinity array allocation and initialization.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Add a common helper to decode both primary_temp (full map, map<pg_t,
u32>) and new_primary_temp (inc map, same) and switch to it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Add primary_temp mappings infrastructure. struct ceph_pg_mapping is
overloaded, primary_temp mappings are stored in an rb-tree, rooted at
ceph_osdmap, in a manner similar to pg_temp mappings.
Dump primary_temp mappings to /sys/kernel/debug/ceph/<client>/osdmap,
one 'primary_temp <pgid> <osd>' per line, e.g:
primary_temp 2.6 4
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
In preparation for adding support for primary_temp mappings, generalize
struct ceph_pg_mapping so it can hold mappings other than pg_temp.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Full and incremental osdmaps are structured identically and have
identical headers. Add a helper to decode both "old" (16-bit version,
v6) and "new" (8-bit struct_v+struct_compat+struct_len, v7) osdmap
enconding headers and switch to it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Consolidate pg_temp (full map, map<pg_t, vector<u32>>) and new_pg_temp
(inc map, same) decoding logic into a common helper and switch to it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Use krealloc() instead of rolling our own. (krealloc() with a NULL
first argument acts as a kmalloc()). Properly initalize the new array
elements. This is needed to make future additions to osdmap easier.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Consolidate pools (full map, map<u64, pg_pool_t>) and new_pools (inc
map, same) decoding logic into a common helper and switch to it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
To be in line with all the other osdmap decode helpers.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Sum up sizeof(...) results instead of (incorrectly) hard-coding the
number of bytes, expressed in ints and longs.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Only version 6 of osdmap encoding is supported, anything other than
version 6 results in an error and halts the decoding process. Checking
if version is >= 5 is therefore bogus.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
The existing error handling scheme requires resetting err to -EINVAL
prior to calling any ceph_decode_* macro. This is ugly and fragile,
and there already are a few places where we would return 0 on error,
due to a missing reset. Follow osdmap_decode() and fix this by adding
a special e_inval label to be used by all ceph_decode_* macros.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
The size of the memory area feeded to crush_decode() should be limited
not only by osdmap end, but also by the crush map length. Also, drop
unnecessary dout() (dout() in crush_decode() conveys the same info) and
step past crush map only if it is decoded successfully.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Check length of osd_state, osd_weight and osd_addr arrays. They
should all have exactly max_osd elements after the call to
osdmap_set_max_osd().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
max_osd value is not covered by any ceph_decode_need(). Use a safe
version of ceph_decode_* macro to decode it.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
The existing error handling scheme requires resetting err to -EINVAL
prior to calling any ceph_decode_* macro. This is ugly and fragile,
and there already are a few places where we would return 0 on error,
due to a missing reset. Fix this by adding a special e_inval label to
be used by all ceph_decode_* macros.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Split osdmap allocation and initialization into a separate function,
ceph_osdmap_decode().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Dump osdmap in hex on both full and incremental decode errors, to make
it easier to match the contents with error offset. dout() map epoch
and max_osd value on success.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Dump pg_temp mappings to /sys/kernel/debug/ceph/<client>/osdmap,
one 'pg_temp <pgid> [<osd>, ..., <osd>]' per line, e.g:
pg_temp 2.6 [2,3,4]
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
To save screen space in anticipation of more fields (e.g. primary
affinity).
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
To make it more readable and save screen space.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
This lets you adjust the vary_r tunable on a per-rule basis.
Reflects ceph.git commit f944ccc20aee60a7d8da7e405ec75ad1cd449fac.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
|
The current crush_choose_firstn code will re-use the same 'r' value for
the recursive call. That means that if we are hitting a collision or
rejection for some reason (say, an OSD that is marked out) and need to
retry, we will keep making the same (bad) choice in that recursive
selection.
Introduce a tunable that fixes that behavior by incorporating the parent
'r' value into the recursive starting point, so that a different path
will be taken in subsequent placement attempts.
Note that this was done from the get-go for the new crush_choose_indep
algorithm.
This was exposed by a user who was seeing PGs stuck in active+remapped
after reweight-by-utilization because the up set mapped to a single OSD.
Reflects ceph.git commit a8e6c9fbf88bad056dd05d3eb790e98a5e43451a.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
|
These two fields are misnomers; they are *retry* counts.
Reflects ceph.git commit f17caba8ae0cad7b6f8f35e53e5f73b444696835.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
|
Back in 27f4d1f6bc32c2ed7b2c5080cbd58b14df622607 we refactored the CRUSH
code to allow adjustment of the retry counts on a per-pool basis. That
commit had an off-by-one bug: the previous "tries" counter was a *retry*
count, not a *try* count, but the new code was passing in 1 meaning
there should be no retries.
Fix the ftotal vs tries comparison to use < instead of <= to fix the
problem. Note that the original code used <= here, which means the
global "choose_total_tries" tunable is actually counting retries.
Compensate for that by adding 1 in crush_do_rule when we pull the tunable
into the local variable.
This was noticed looking at output from a user provided osdmap.
Unfortunately the map doesn't illustrate the change in mapping behavior
and I haven't managed to construct one yet that does. Inspection of the
crush debug output now aligns with prior versions, though.
Reflects ceph.git commit 795704fd615f0b008dcc81aa088a859b2d075138.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
|
|
When there is no more data, ceph_msg_data_{pages,pagelist}_advance()
should not move on to the next page.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
|
|
This is primarily for rbd's benefit and is supposed to combat
fragmentation:
"... knowing that rbd images have a 4m size, librbd can pass a hint
that will let the osd do the xfs allocation size ioctl on new files so
that they are allocated in 1m or 4m chunks. We've seen cases where
users with rbd workloads have very high levels of fragmentation in xfs
and this would mitigate that and probably have a pretty nice
performance benefit."
SETALLOCHINT is considered advisory, so our backwards compatibility
mechanism here is to set FAILOK flag for all SETALLOCHINT ops.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
Encode ceph_osd_op::flags field so that it gets sent over the wire.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
|
|
With the addition of erasure coding support in the future, scratch
variable-length array in crush_do_rule_ary() is going to grow to at
least 200 bytes on average, on top of another 128 bytes consumed by
rawosd/osd arrays in the call chain. Replace it with a buffer inside
struct osdmap and a mutex. This shouldn't result in any contention,
because all osd requests were already serialized by request_mutex at
that point; the only unlocked caller was ceph_ioctl_get_dataloc().
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
|
|
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference. The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set. It will then try
to get the table pointer and process the packet based
on the table. Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems I missed one change in get_timewait4_sock() to compute
the remaining time before deletion of IPV4 timewait socket.
This could result in wrong output in /proc/net/tcp for tm->when field.
Fixes: 96f817fedec4 ("tcp: shrink tcp6_timewait_sock by one cache line")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two problematic situations.
A deadlock can happen when is_percpu is false because it can get
interrupted while holding the spinlock. Then it executes
ovs_flow_stats_update() in softirq context which tries to get
the same lock.
The second sitation is that when is_percpu is true, the code
correctly disables BH but only for the local CPU, so the
following can happen when locking the remote CPU without
disabling BH:
CPU#0 CPU#1
ovs_flow_stats_get()
stats_read()
+->spin_lock remote CPU#1 ovs_flow_stats_get()
| <interrupted> stats_read()
| ... +--> spin_lock remote CPU#0
| | <interrupted>
| ovs_flow_stats_update() | ...
| spin_lock local CPU#0 <--+ ovs_flow_stats_update()
+---------------------------------- spin_lock local CPU#1
This patch disables BH for both cases fixing the deadlocks.
Acked-by: Jesse Gross <jesse@nicira.com>
=================================
[ INFO: inconsistent lock state ]
3.14.0-rc8-00007-g632b06a #1 Tainted: G I
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[5]:HE1:SE0] takes:
(&(&cpu_stats->lock)->rlock){+.?...}, at: [<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810f973f>] __lock_acquire+0x68f/0x1c40
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd9e4>] ovs_flow_stats_get+0xc4/0x1e0 [openvswitch]
[<ffffffffa05da855>] ovs_flow_cmd_fill_info+0x185/0x360 [openvswitch]
[<ffffffffa05daf05>] ovs_flow_cmd_build_info.constprop.27+0x55/0x90 [openvswitch]
[<ffffffffa05db41d>] ovs_flow_cmd_new_or_set+0x4dd/0x570 [openvswitch]
[<ffffffff816c245d>] genl_family_rcv_msg+0x1cd/0x3f0
[<ffffffff816c270e>] genl_rcv_msg+0x8e/0xd0
[<ffffffff816c0239>] netlink_rcv_skb+0xa9/0xc0
[<ffffffff816c0798>] genl_rcv+0x28/0x40
[<ffffffff816bf830>] netlink_unicast+0x100/0x1e0
[<ffffffff816bfc57>] netlink_sendmsg+0x347/0x770
[<ffffffff81668e9c>] sock_sendmsg+0x9c/0xe0
[<ffffffff816692d9>] ___sys_sendmsg+0x3a9/0x3c0
[<ffffffff8166a911>] __sys_sendmsg+0x51/0x90
[<ffffffff8166a962>] SyS_sendmsg+0x12/0x20
[<ffffffff817e3ce9>] system_call_fastpath+0x16/0x1b
irq event stamp: 1740726
hardirqs last enabled at (1740726): [<ffffffff8175d5e0>] ip6_finish_output2+0x4f0/0x840
hardirqs last disabled at (1740725): [<ffffffff8175d59b>] ip6_finish_output2+0x4ab/0x840
softirqs last enabled at (1740674): [<ffffffff8109be12>] _local_bh_enable+0x22/0x50
softirqs last disabled at (1740675): [<ffffffff8109db05>] irq_exit+0xc5/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&cpu_stats->lock)->rlock);
<Interrupt>
lock(&(&cpu_stats->lock)->rlock);
*** DEADLOCK ***
5 locks held by swapper/0/0:
#0: (((&ifa->dad_timer))){+.-...}, at: [<ffffffff810a7155>] call_timer_fn+0x5/0x320
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff81788a55>] mld_sendpack+0x5/0x4a0
#2: (rcu_read_lock_bh){.+....}, at: [<ffffffff8175d149>] ip6_finish_output2+0x59/0x840
#3: (rcu_read_lock_bh){.+....}, at: [<ffffffff8168ba75>] __dev_queue_xmit+0x5/0x9b0
#4: (rcu_read_lock){.+.+..}, at: [<ffffffffa05e41b5>] internal_dev_xmit+0x5/0x110 [openvswitch]
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G I 3.14.0-rc8-00007-g632b06a #1
Hardware name: /DX58SO, BIOS SOX5810J.86A.5599.2012.0529.2218 05/29/2012
0000000000000000 0fcf20709903df0c ffff88042d603808 ffffffff817cfe3c
ffffffff81c134c0 ffff88042d603858 ffffffff817cb6da 0000000000000005
ffffffff00000001 ffff880400000000 0000000000000006 ffffffff81c134c0
Call Trace:
<IRQ> [<ffffffff817cfe3c>] dump_stack+0x4d/0x66
[<ffffffff817cb6da>] print_usage_bug+0x1f4/0x205
[<ffffffff810f7f10>] ? check_usage_backwards+0x180/0x180
[<ffffffff810f8963>] mark_lock+0x223/0x2b0
[<ffffffff810f96d3>] __lock_acquire+0x623/0x1c40
[<ffffffff810f5707>] ? __lock_is_held+0x57/0x80
[<ffffffffa05e26c6>] ? masked_flow_lookup+0x236/0x250 [openvswitch]
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dcc64>] ovs_dp_process_received_packet+0x84/0x120 [openvswitch]
[<ffffffff810f93f7>] ? __lock_acquire+0x347/0x1c40
[<ffffffffa05e3bea>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa05e4218>] internal_dev_xmit+0x68/0x110 [openvswitch]
[<ffffffffa05e41b5>] ? internal_dev_xmit+0x5/0x110 [openvswitch]
[<ffffffff8168b4a6>] dev_hard_start_xmit+0x2e6/0x8b0
[<ffffffff8168be87>] __dev_queue_xmit+0x417/0x9b0
[<ffffffff8168ba75>] ? __dev_queue_xmit+0x5/0x9b0
[<ffffffff8175d5e0>] ? ip6_finish_output2+0x4f0/0x840
[<ffffffff8168c430>] dev_queue_xmit+0x10/0x20
[<ffffffff8175d641>] ip6_finish_output2+0x551/0x840
[<ffffffff8176128a>] ? ip6_finish_output+0x9a/0x220
[<ffffffff8176128a>] ip6_finish_output+0x9a/0x220
[<ffffffff8176145f>] ip6_output+0x4f/0x1f0
[<ffffffff81788c29>] mld_sendpack+0x1d9/0x4a0
[<ffffffff817895b8>] mld_send_initial_cr.part.32+0x88/0xa0
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8178e301>] ipv6_mc_dad_complete+0x31/0x50
[<ffffffff817690d7>] addrconf_dad_completed+0x147/0x220
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8176934f>] addrconf_dad_timer+0x19f/0x1c0
[<ffffffff810a71e9>] call_timer_fn+0x99/0x320
[<ffffffff810a7155>] ? call_timer_fn+0x5/0x320
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff810a76c4>] run_timer_softirq+0x254/0x3b0
[<ffffffff8109d47d>] __do_softirq+0x12d/0x480
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if the card supports CTAG acceleration we do not
account for the vlan header even if we are configuring an
8021AD vlan. This may not be best since we'll do software
tagging for 8021AD which will cause data copy on skb head expansion
Configure the length based on available hw offload capabilities and
vlan protocol.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02b00704 ("net: fix multithreaded signal handling in
unix recv routines").
To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.
Fixes: b3ca9b02b00704 ("net: fix multithreaded signal handling in unix recv routines")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 10ddceb22ba (ip_tunnel:multicast process cause panic due
to skb->_skb_refdst NULL pointer) removed dst-drop call from
ip-tunnel-recv.
Following commit reintroduce dst-drop and fix the original bug by
checking loopback packet before releasing dst.
Original bug: https://bugzilla.kernel.org/show_bug.cgi?id=70681
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a topology event subscription fails for any reason, such as out
of memory, max number reached or because we received an invalid
request the correct behavior is to terminate the subscribers
connection to the topology server. This is currently broken and
produces the following oops:
[27.953662] tipc: Subscription rejected, illegal request
[27.955329] BUG: spinlock recursion on CPU#1, kworker/u4:0/6
[27.957066] lock: 0xffff88003c67f408, .magic: dead4ead, .owner: kworker/u4:0/6, .owner_cpu: 1
[27.958054] CPU: 1 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.0-rc6+ #5
[27.960230] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[27.960874] Workqueue: tipc_rcv tipc_recv_work [tipc]
[27.961430] ffff88003c67f408 ffff88003de27c18 ffffffff815c0207 ffff88003de1c050
[27.962292] ffff88003de27c38 ffffffff815beec5 ffff88003c67f408 ffffffff817f0a8a
[27.963152] ffff88003de27c58 ffffffff815beeeb ffff88003c67f408 ffffffffa0013520
[27.964023] Call Trace:
[27.964292] [<ffffffff815c0207>] dump_stack+0x45/0x56
[27.964874] [<ffffffff815beec5>] spin_dump+0x8c/0x91
[27.965420] [<ffffffff815beeeb>] spin_bug+0x21/0x26
[27.965995] [<ffffffff81083df6>] do_raw_spin_lock+0x116/0x140
[27.966631] [<ffffffff815c6215>] _raw_spin_lock_bh+0x15/0x20
[27.967256] [<ffffffffa0008540>] subscr_conn_shutdown_event+0x20/0xa0 [tipc]
[27.968051] [<ffffffffa000fde4>] tipc_close_conn+0xa4/0xb0 [tipc]
[27.968722] [<ffffffffa00101ba>] tipc_conn_terminate+0x1a/0x30 [tipc]
[27.969436] [<ffffffffa00089a2>] subscr_conn_msg_event+0x1f2/0x2f0 [tipc]
[27.970209] [<ffffffffa0010000>] tipc_receive_from_sock+0x90/0xf0 [tipc]
[27.970972] [<ffffffffa000fa79>] tipc_recv_work+0x29/0x50 [tipc]
[27.971633] [<ffffffff8105dbf5>] process_one_work+0x165/0x3e0
[27.972267] [<ffffffff8105e869>] worker_thread+0x119/0x3a0
[27.972896] [<ffffffff8105e750>] ? manage_workers.isra.25+0x2a0/0x2a0
[27.973622] [<ffffffff810648af>] kthread+0xdf/0x100
[27.974168] [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
[27.974893] [<ffffffff815ce13c>] ret_from_fork+0x7c/0xb0
[27.975466] [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
The recursion occurs when subscr_terminate tries to grab the
subscriber lock, which is already taken by subscr_conn_msg_event.
We fix this by checking if the request to establish a new
subscription was successful, and if not we initiate termination of
the subscriber after we have released the subscriber lock.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
