summaryrefslogtreecommitdiff
path: root/drivers/usb/core
AgeCommit message (Collapse)AuthorFilesLines
2017-12-13USB: core: prevent malicious bNumInterfaces overflowAlan Stern1-1/+3
A malicious USB device with crafted descriptors can cause the kernel to access unallocated memory by setting the bNumInterfaces value too high in a configuration descriptor. Although the value is adjusted during parsing, this adjustment is skipped in one of the error return paths. This patch prevents the problem by setting bNumInterfaces to 0 initially. The existing code already sets it to the proper value after parsing is complete. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-13Revert "USB: core: only clean up what we allocated"Greg Kroah-Hartman1-6/+3
This reverts commit 32fd87b3bbf5f7a045546401dfe2894dbbf4d8c3. Alan wrote a better fix for this... Cc: Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-12USB: core: only clean up what we allocatedAndrey Konovalov1-3/+6
When cleaning up the configurations, make sure we only free the number of configurations and interfaces that we could have allocated. Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28usb: quirks: Add no-lpm quirk for KY-688 USB 3.1 Type-C HubKai-Heng Feng1-0/+3
KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect to Realtek r8153. Similar to commit ("7496cfe5431f2 usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28usb: hub: Cycle HUB power when initialization failsMike Looijmans1-0/+9
Sometimes the USB device gets confused about the state of the initialization and the connection fails. In particular, the device thinks that it's already set up and running while the host thinks the device still needs to be configured. To work around this issue, power-cycle the hub's output to issue a sort of "reset" to the device. This makes the device restart its state machine and then the initialization succeeds. This fixes problems where the kernel reports a list of errors like this: usb 1-1.3: device not accepting address 19, error -71 The end result is a non-functioning device. After this patch, the sequence becomes like this: usb 1-1.3: new high-speed USB device number 18 using ci_hdrc usb 1-1.3: device not accepting address 18, error -71 usb 1-1.3: new high-speed USB device number 19 using ci_hdrc usb 1-1.3: device not accepting address 19, error -71 usb 1-1-port3: attempt power cycle usb 1-1.3: new high-speed USB device number 21 using ci_hdrc usb-storage 1-1.3:1.2: USB Mass Storage device detected Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28USB: core: Add type-specific length check of BOS descriptorsMasakazu Mokuno1-4/+24
As most of BOS descriptors are longer in length than their header 'struct usb_dev_cap_header', comparing solely with it is not sufficient to avoid out-of-bounds access to BOS descriptors. This patch adds descriptor type specific length check in usb_get_bos_descriptor() to fix the issue. Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28USB: usbfs: Filter flags passed in from user spaceOliver Neukum1-5/+9
USBDEVFS_URB_ISO_ASAP must be accepted only for ISO endpoints. Improve sanity checking. Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook1-3/+5
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-14Merge tag 'sound-4.15-rc1' of ↵Linus Torvalds1-4/+26
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "There are no big surprising changes in this cycle, yet not too boring, either. The biggest change from diffstat POV is the removal of the legacy OSS driver codes that have been already disabled for a long time. This will bring a few trivial merge conflicts. As new features in ASoC side, there are two things: a new AC97 bus implementation and AMD Stony platform support. Both include the relevant changes shared with other subsystems, e.g. AC97 MFD changes and DRM AMD changes. Some other highlighted topics are: - A bunch of USB-audio drivers got the hardening against the malicious device accesses with a new helper code for endpoint sanity check - Lots of cleanups for ASoC Intel platform code, including support for their open source audio firmware - Continued ASoC core componentization works - Support for scaling MCLK with sample rate in ASoC simple-card - Stabler PCM hot-unplug capability, especially for ASoC usages" * tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits) Documentation: sound: hd-audio: notes.rst ASoC: bcm2835: Support left/right justified and DSP modes ASoC: bcm2835: Enforce full symmetry ASoC: bcm2835: Support additional samplerates up to 384kHz ASoC: bcm2835: Add support for TDM modes ASoC: add mclk-fs support to audio graph card ASoC: add mclk-fs to audio graph card binding ASoC: rt5514: work around link error ASoC: rt5514: mark PM functions as __maybe_unused ASoC: rt5663: Check the JD status in the button pushing ASoC: amd: Modified DMA transfer Mechanism for Playback ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2 ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+ ASoC: da7213: add support for DSP modes ASoC: sun8i-codec: Add a comment on the LRCK inversion ASoC: sun8i-codec: Set the BCLK divider ASoC: rt5663: Delay and retry reading rt5663 ID register ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds ASoC: cs42l56: Fix reset GPIO name in example DT binding ASoC: rt5514-spi: check irq status to schedule data copy in resume function ...
2017-11-13Merge tag 'usb-4.15-rc1' of ↵Linus Torvalds24-139/+123
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver updates for 4.15-rc1. There is the usual amount of gadget and xhci driver updates, along with phy and chipidea enhancements. There's also a lot of SPDX tags and license boilerplate cleanups as well, which provide some churn in the diffstat. Other major thing is the typec code that moved out of staging and into the "real" part of the drivers/usb/ tree, which was nice to see happen. All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits) usb: gadget: f_fs: Fix use-after-free in ffs_free_inst USB: usbfs: compute urb->actual_length for isochronous usb: core: message: remember to reset 'ret' to 0 when necessary USB: typec: Remove remaining redundant license text USB: typec: add SPDX identifiers to some files USB: renesas_usbhs: rcar?.h: add SPDX tags USB: chipidea: ci_hdrc_tegra.c: add SPDX line USB: host: xhci-debugfs: add SPDX lines USB: add SPDX identifiers to all remaining Makefiles usb: host: isp1362-hcd: remove a couple of redundant assignments USB: adutux: remove redundant variable minor usb: core: add a new usb_get_ptm_status() helper usb: core: add a 'type' parameter to usb_get_status() usb: core: introduce a new usb_get_std_status() helper usb: core: rename usb_get_status() 'type' argument to 'recip' usb: core: add Status Type definitions USB: gadget: Remove redundant license text USB: gadget: function: Remove redundant license text USB: gadget: udc: Remove redundant license text USB: gadget: legacy: Remove redundant license text ...
2017-11-13Merge tag 'asoc-v4.15' of ↵Takashi Iwai1-0/+1
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus ASoC: Updates for v4.15 The biggest thing this release has been the conversion of the AC98 bus to the driver model, that's been a long time coming so thanks to Robert Jarzmik for his dedication there. Due to there being some AC97 MFD there's a few fairly large changes in input and the MFD layer, mainly to the wm97xx driver. There's also some drivers/drm changes to support the new AMD Stoney platform, these are shared with the DRM subsystem and should be being merged via both. Within the subsystem the overwhelming bulk of the changes is in the Intel drivers which continue to need lots of cleanups and fixes, this release they've also gained support for their open source firmware. There's also some large changs in the core as Morimoto-san continues to mirror operations into the component level in preparation for conversion of drivers to that. - The AC97 bus has finally caught up with the driver model thanks to some dedicated and persistent work from Robert Jarzmik. - Continued work from Morimoto-san on moving us towards being able to use components for everything. - Lots of cleanups for the Intel platform code, including support for their open source audio firmware. - Support for scaling MCLK with sample rate in simple-card. - Support for AMD Stoney platform.
2017-11-13Merge branch 'for-next' into for-linusTakashi Iwai1-4/+26
Pull 4.15 updates to take over the previous urgent fixes. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-11-09USB: usbfs: compute urb->actual_length for isochronousAlan Stern1-0/+14
The USB kerneldoc says that the actual_length field "is read in non-iso completion functions", but the usbfs driver uses it for all URB types in processcompl(). Since not all of the host controller drivers set actual_length for isochronous URBs, programs using usbfs with some host controllers don't work properly. For example, Minas reports that a USB camera controlled by libusb doesn't work properly with a dwc2 controller. It doesn't seem worthwhile to change the HCDs and the documentation, since the in-kernel USB class drivers evidently don't rely on actual_length for isochronous transfers. The easiest solution is for usbfs to calculate the actual_length value for itself, by adding up the lengths of the individual packets in an isochronous transfer. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Reported-and-tested-by: wlf <wulf@rock-chips.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-09usb: core: message: remember to reset 'ret' to 0 when necessaryFelipe Balbi1-0/+2
usb_control_msg() will return the amount of bytes transferred, if that amount matches what we wanted to transfer, we need to reset 'ret' to 0 from usb_get_status(). Fixes: 2e43f0fe379c ("usb: core: add a 'type' parameter to usb_get_status()") Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07usb: core: add a 'type' parameter to usb_get_status()Felipe Balbi1-7/+40
This new 'type' parameter will allows interested drivers to request for PTM status or Standard status. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07usb: core: introduce a new usb_get_std_status() helperFelipe Balbi2-6/+6
This new helper is a simple wrapper around usb_get_status(). This patch is in preparation to adding support for fetching PTM_STATUS types. No functional changes. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07usb: core: rename usb_get_status() 'type' argument to 'recip'Felipe Balbi1-3/+3
This makes it a lot clearer that we're expecting a recipient as the argument. A follow-up patch will use the argument 'type' as the status type selector (standard or ptm). Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07usb: core: add Status Type definitionsFelipe Balbi1-2/+2
USB 3.1 added a PTM_STATUS type. Let's add a define for it and following patches will let usb_get_status() accept the new argument. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07Merge branch 'linus' into locking/core, to resolve conflictsIngo Molnar1-0/+1
Conflicts: include/linux/compiler-clang.h include/linux/compiler-gcc.h include/linux/compiler-intel.h include/uapi/linux/stddef.h Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-11-04USB: Add delay-init quirk for Corsair K70 LUX keyboardsBernhard Rosenkraenzer1-0/+3
Without this patch, K70 LUX keyboards don't work, saying usb 3-3: unable to read config index 0 descriptor/all usb 3-3: can't read configurations, error -110 usb usb3-port3: unable to enumerate USB device Signed-off-by: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04USB: core: Remove redundant license textGreg Kroah-Hartman11-107/+0
Now that the SPDX tag is in all USB files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04USB: add SPDX identifiers to all remaining files in drivers/usb/Greg Kroah-Hartman11-0/+11
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/usb/ and include/linux/usb* files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-03USB: core: move existing SPDX tags to top of the fileGreg Kroah-Hartman13-13/+13
To match the rest of the kernel, the SPDX tags for the drivers/usb/core/ files are moved to the first line of the file. This makes it more obvious the tag is present as well as making it match the other 12k files in the tree with this location. It also uses // to match the "expected style" as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01usb: core: urb: mark expected switch fall-throughGustavo A. R. Silva1-0/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1162594 Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-25locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns ↵Mark Rutland2-3/+3
to READ_ONCE()/WRITE_ONCE() Please do not apply this to mainline directly, instead please re-run the coccinelle script shown below and apply its output. For several reasons, it is desirable to use {READ,WRITE}_ONCE() in preference to ACCESS_ONCE(), and new code is expected to use one of the former. So far, there's been no reason to change most existing uses of ACCESS_ONCE(), as these aren't harmful, and changing them results in churn. However, for some features, the read/write distinction is critical to correct operation. To distinguish these cases, separate read/write accessors must be used. This patch migrates (most) remaining ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following coccinelle script: ---- // Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and // WRITE_ONCE() // $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch virtual patch @ depends on patch @ expression E1, E2; @@ - ACCESS_ONCE(E1) = E2 + WRITE_ONCE(E1, E2) @ depends on patch @ expression E; @@ - ACCESS_ONCE(E) + READ_ONCE(E) ---- Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: davem@davemloft.net Cc: linux-arch@vger.kernel.org Cc: mpe@ellerman.id.au Cc: shuah@kernel.org Cc: snitzer@redhat.com Cc: thor.thayer@linux.intel.com Cc: tj@kernel.org Cc: viro@zeniv.linux.org.uk Cc: will.deacon@arm.com Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-10-23Merge 4.14-rc6 into usb-nextGreg Kroah-Hartman4-11/+16
We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-23USB: Force disconnect Huawei 4G modem during suspendDaniel Drake4-1/+29
When going into S3 suspend, the Acer TravelMate P648-M and P648-G3 laptops immediately wake up 3-4 seconds later for no obvious reason. Unbinding the integrated Huawei 4G LTE modem before suspend avoids the issue, even though we are not using the modem at all (checked from rescue.target/runlevel1). The problem also occurs when the option and cdc-ether modem drivers aren't loaded; it reproduces just with the base usb driver. Under Windows the system can suspend fine. Seeking a better fix, we've tried a lot of things, including: - Check that the device's power/wakeup is disabled - Check that remote wakeup is off at the USB level - All the quirks in drivers/usb/core/quirks.c e.g. USB_QUIRK_RESET_RESUME, USB_QUIRK_RESET, USB_QUIRK_IGNORE_REMOTE_WAKEUP, USB_QUIRK_NO_LPM. but none of that makes any difference. There are no errors in the logs showing any suspend/resume-related issues. When the system wakes up due to the modem, log-wise it appears to be a normal resume. Introduce a quirk to disable the port during suspend when the modem is detected. The modem from the P648-G3 model is: T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=12d1 ProdID=15c3 Rev= 1.02 S: Manufacturer=Huawei Technologies Co., Ltd. S: Product=HUAWEI Mobile S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver= E: Ad=82(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver= E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver= E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver= E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I: If#= 3 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=16 Driver= E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=2ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver= E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms C:* #Ifs= 6 Cfg#= 2 Atr=a0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms C: #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr= 2mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver= E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver= I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver= E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Based on an earlier patch by Chris Chiu. Signed-off-by: Daniel Drake <drake@endlessm.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-19usb: hub: Allow reset retry for USB2 devices on connect bounceMathias Nyman1-4/+7
If the connect status change is set during reset signaling, but the status remains connected just retry port reset. This solves an issue with connecting a 90W HP Thunderbolt 3 dock with a Lenovo Carbon x1 (5th generation) which causes a 30min loop of a high speed device being re-discovererd before usb ports starts working. [...] [ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd [ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd [ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd [...] This is caused by a high speed device that doesn't successfully go to the enabled state after the second port reset. Instead the connection bounces (connected, with connect status change), bailing out completely from enumeration just to restart from scratch. Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332 Cc: Stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-18USB: core: fix out-of-bounds access bug in usb_get_bos_descriptor()Alan Stern1-2/+4
Andrey used the syzkaller fuzzer to find an out-of-bounds memory access in usb_get_bos_descriptor(). The code wasn't checking that the next usb_dev_cap_header structure could fit into the remaining buffer space. This patch fixes the error and also reduces the bNumDeviceCaps field in the header to match the actual number of capabilities found, in cases where there are fewer than expected. Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-17usb: Apply hardware LPM attributes to 3.1 deviceLu Baolu1-1/+2
The devices running at SuperSpeedPlus speed are also LPM capable. Apply usb3 hardware LPM attributes to those devices as well. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-17usb: quirks: add quirk for WORLDE MINI MIDI keyboardFelipe Balbi1-0/+4
This keyboard doesn't implement Get String descriptors properly even though string indexes are valid. What happens is that when requesting for the String descriptor, the device disconnects and reconnects. Without this quirk, this loop will continue forever. Cc: Alan Stern <stern@rowland.harvard.edu> Reported-by: Владимир Мартьянов <vilgeforce@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-17USB: devio: Revert "USB: devio: Don't corrupt user memory"Hans de Goede1-5/+1
Taking the uurb->buffer_length userspace passes in as a maximum for the actual urbs transfer_buffer_length causes 2 serious issues: 1) It breaks isochronous support for all userspace apps using libusb, as existing libusb versions pass in 0 for uurb->buffer_length, relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc descriptors passed in added together as buffer length. This for example causes redirection of USB audio and Webcam's into virtual machines using qemu-kvm to no longer work. This is a userspace ABI break and as such must be reverted. Note that the original commit does not protect other users / the kernels memory, it only stops the userspace process making the call from shooting itself in the foot. 2) It may cause the kernel to program host controllers to DMA over random memory. Just as the devio code used to only look at the iso_packet_desc lenghts, the host drivers do the same, relying on the submitter of the urbs to make sure the entire buffer is large enough and not checking transfer_buffer_length. But the "USB: devio: Don't corrupt user memory" commit now takes the userspace provided uurb->buffer_length for the buffer-size while copying over the user-provided iso_packet_desc lengths 1:1, allowing the user to specify a small buffer size while programming the host controller to dma a lot more data. (Atleast the ohci, uhci, xhci and fhci drivers do not check transfer_buffer_length for isoc transfers.) This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory") fixing both these issues. Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-11usb: core: Add a helper function to check the validity of EP type in URBTakashi Iwai1-4/+26
This patch adds a new helper function to perform a sanity check of the given URB to see whether it contains a valid endpoint. It's a light- weight version of what usb_submit_urb() does, but without the kernel warning followed by the stack trace, just returns an error code. Especially for a driver that doesn't parse the descriptor but fills the URB with the fixed endpoint (e.g. some quirks for non-compliant devices), this kind of check is preferable at the probe phase before actually submitting the urb. Tested-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2017-10-09Merge 4.14-rc4 into usb-nextGreg Kroah-Hartman4-6/+27
This merges in the USB fixes that we need here. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-04drivers: usb: hcd: use setup_timer() helper.Allen Pais1-3/+1
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-25USB: devio: Don't corrupt user memoryDan Carpenter1-1/+5
The user buffer has "uurb->buffer_length" bytes. If the kernel has more information than that, we should truncate it instead of writing past the end of the user's buffer. I added a WARN_ONCE() to help the user debug the issue. Reported-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-25USB: devio: Prevent integer overflow in proc_do_submiturb()Dan Carpenter1-0/+5
There used to be an integer overflow check in proc_do_submiturb() but we removed it. It turns out that it's still required. The uurb->buffer_length variable is a signed integer and it's controlled by the user. It can lead to an integer overflow when we do: num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE); If we strip away the macro then that line looks like this: num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ It's the first addition which can overflow. Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit") Cc: stable <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-21USB: core: harden cdc_parse_cdc_headerGreg Kroah-Hartman1-0/+4
Andrey Konovalov reported a possible out-of-bounds problem for the cdc_parse_cdc_header function. He writes: It looks like cdc_parse_cdc_header() doesn't validate buflen before accessing buffer[1], buffer[2] and so on. The only check present is while (buflen > 0). So fix this issue up by properly validating the buffer length matches what the descriptor says it is. Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-19USB: fix out-of-bounds in usb_set_configurationGreg Kroah-Hartman1-3/+11
Andrey Konovalov reported a possible out-of-bounds problem for a USB interface association descriptor. He writes: It seems there's no proper size check of a USB_DT_INTERFACE_ASSOCIATION descriptor. It's only checked that the size is >= 2 in usb_parse_configuration(), so find_iad() might do out-of-bounds access to intf_assoc->bInterfaceCount. And he's right, we don't check for crazy descriptors of this type very well, so resolve this problem. Yet another issue found by syzkaller... Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-18usb: Increase quirk delay for USB devicesDmitry Fleytman2-2/+2
Commit e0429362ab15 ("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e") introduced quirk to workaround an issue with some Logitech webcams. The workaround is introducing delay for some USB operations. According to our testing, delay introduced by original commit is not long enough and in rare cases we still see issues described by the aforementioned commit. This patch increases delays introduced by original commit. Having this patch applied we do not see those problems anymore. Signed-off-by: Dmitry Fleytman <dmitry@daynix.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-29usb: core: usbport: fix "BUG: key not in .data" when lockdep is enabledChristian Lamparter1-0/+1
This patch fixes a splat that happens if CONFIG_DEBUG_LOCK_ALLOC is enabled and the ledtrig_usbport is loaded. (on a device that has some usb ports). [ 60.695479] BUG: key c53f8420 not in .data! [ 60.695521] ------------[ cut here ]------------ [ 60.698542] WARNING: CPU: 1 PID: 854 at kernel/locking/lockdep.c:3134 __kernfs_create_file+0x5c/0xc0 [ 60.703355] DEBUG_LOCKS_WARN_ON(1) [ 60.712534] Modules linked in: [ 60.944078] CPU: 1 PID: 854 Comm: S96led Not tainted 4.9.44 #0 [ 60.944329] Hardware name: Generic DT based system [ 60.950106] [<c021585c>] (unwind_backtrace) from [<c0212150>] (show_stack+0x10/0x14) [ 60.954878] [<c0212150>] (show_stack) from [<c03a2bc4>] (dump_stack+0x7c/0x9c) [ 60.962772] [<c03a2bc4>] (dump_stack) from [<c021db34>] (__warn+0xbc/0xec) [ 60.969799] [<c021db34>] (__warn) from [<c021db98>] (warn_slowpath_fmt+0x34/0x44) [ 60.976656] [<c021db98>] (warn_slowpath_fmt) [ 60.984210] [<c0320688>] (__kernfs_create_file) [ 60.992712] [<c0320ef0>] (sysfs_add_file_mode_ns) [ 61.002090] [<c0321044>] (sysfs_add_file) from [ 61.010619] [<c0321094>] (sysfs_add_file_to_group) [ 61.019263] [<bf24a47c>] (usbport_trig_add_usb_dev_ports [ledtrig_usbport]) [ 61.031002] [<c0430414>] (bus_for_each_dev) [ 61.042106] [<c0497dc4>] (usb_for_each_dev) [ 61.050375] [<bf24a2ac>] (usbport_trig_activate [ledtrig_usbport]) [ 61.060685] [<c04e1708>] (led_trigger_set) from [<c04e1834>] [...] Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28usb: Add device quirk for Logitech HD Pro Webcam C920-CDmitry Fleytman1-1/+2
Commit e0429362ab15 ("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e") introduced quirk to workaround an issue with some Logitech webcams. Apparently model C920-C has the same issue so applying the same quirk as well. See aforementioned commit message for detailed explanation of the problem. Signed-off-by: Dmitry Fleytman <dmitry@daynix.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28usb: quirks: add delay init quirk for Corsair Strafe RGB keyboardKai-Heng Feng1-0/+3
Corsair Strafe RGB keyboard has trouble to initialize: [ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd [ 6.871136] usb 3-6: unable to read config index 0 descriptor/all [ 6.871138] usb 3-6: can't read configurations, error -110 [ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd [ 12.246642] usb 3-6: unable to read config index 0 descriptor/all [ 12.246644] usb 3-6: can't read configurations, error -110 [ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd [ 17.622145] usb 3-6: unable to read config index 0 descriptor/all [ 17.622147] usb 3-6: can't read configurations, error -110 [ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd [ 22.997715] usb 3-6: unable to read config index 0 descriptor/all [ 22.997716] usb 3-6: can't read configurations, error -110 Although it may work after several times unpluging/pluging: [ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd [ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20 [ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard [ 68.337468] usb 3-6: Manufacturer: Corsair [ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941 Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone can workaround this issue. Hence add the quirk for Corsair Strafe RGB. BugLink: https://bugs.launchpad.net/bugs/1678477 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28USB: core: constify vm_operations_structArvind Yadav1-1/+1
vm_operations_struct are not supposed to change at runtime. All functions working with const vm_operations_struct. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28USB: core: Avoid race of async_completed() w/ usbdev_release()Douglas Anderson1-2/+2
While running reboot tests w/ a specific set of USB devices (and slub_debug enabled), I found that once every few hours my device would be crashed with a stack that looked like this: [ 14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091 [ 14.012460] lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu [ 14.012460] /1025536097, .owner_cpu: 0 [ 14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352 [ 14.012468] Hardware name: Google Kevin (DT) [ 14.012471] Call trace: [ 14.012483] [<....>] dump_backtrace+0x0/0x160 [ 14.012487] [<....>] show_stack+0x20/0x28 [ 14.012494] [<....>] dump_stack+0xb4/0xf0 [ 14.012500] [<....>] spin_dump+0x8c/0x98 [ 14.012504] [<....>] spin_bug+0x30/0x3c [ 14.012508] [<....>] do_raw_spin_lock+0x40/0x164 [ 14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74 [ 14.012521] [<....>] __wake_up+0x2c/0x60 [ 14.012528] [<....>] async_completed+0x2d0/0x300 [ 14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138 [ 14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0 [ 14.012544] [<....>] xhci_irq+0x1314/0x1348 [ 14.012548] [<....>] usb_hcd_irq+0x40/0x50 [ 14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0 [ 14.012556] [<....>] handle_irq_event+0x4c/0x7c [ 14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8 [ 14.012564] [<....>] generic_handle_irq+0x30/0x44 [ 14.012568] [<....>] __handle_domain_irq+0x90/0xbc [ 14.012572] [<....>] gic_handle_irq+0xcc/0x18c Investigation using kgdb() found that the wait queue that was passed into wake_up() had been freed (it was filled with slub_debug poison). I analyzed and instrumented the code and reproduced. My current belief is that this is happening: 1. async_completed() is called (from IRQ). Moves "as" onto the completed list. 2. On another CPU, proc_reapurbnonblock_compat() calls async_getcompleted(). Blocks on spinlock. 3. async_completed() releases the lock; keeps running; gets blocked midway through wake_up(). 4. proc_reapurbnonblock_compat() => async_getcompleted() gets the lock; removes "as" from completed list and frees it. 5. usbdev_release() is called. Frees "ps". 6. async_completed() finally continues running wake_up(). ...but wake_up() has a pointer to the freed "ps". The instrumentation that led me to believe this was based on adding some trace_printk() calls in a select few functions and then using kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace below I cheated a little bit and added a udelay(1000) in async_completed() after releasing the spinlock because I wanted it to trigger quicker): <...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200 mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200 mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200) mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080 mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080 <...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200 To fix this problem we can just move the wake_up() under the ps->lock. There should be no issues there that I'm aware of. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-16usb: Increase root hub reset signaling time to prevent retryMathias Nyman1-1/+1
Save 80ms device enumeration time by increasing root hub port reset time The 50ms reset signaling time is not enough for most root hub ports. Increasing the reset time to 60ms allows host controllers to finish port reset and removes a retry causing an extra 50ms delay. The USB 2 specification requires "at least 50ms" for driving root port reset. The current msleep is exactly 50ms which may not be enough if there are any delays between writing the reset bit to host controller portsc register and phy actually driving reset. On Haswell, Skylake and Kabylake xHC port reset took in average 52-59ms The 80ms improvement comes from (40ms * 2 port resets) save at enumeration for each device connected to a root hub port. more details about root port reset in USB2 section 7.1.7.5:. "Software must ensure that resets issued to the root ports drive reset long enough to overwhelm any concurrent resume attempts by downstream devices. It is required that resets from root ports have a duration of at least 50 ms (TDRSTR). Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-14Merge 4.13-rc5 into usb-nextGreg Kroah-Hartman3-5/+13
This gets the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-10usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet AdapterKai-Heng Feng1-0/+3
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to connect to Realtek r8153. The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk can make it work. Since another r8153 dongle at my hand does not have the issue, so add the quirk to the Genesys Logic hub instead. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-10USB: Check for dropped connection before switching to full speedAlan Stern1-4/+6
Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4cc4fe ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-27 10:23:22 +0000