summaryrefslogtreecommitdiff
path: root/drivers/spi
AgeCommit message (Collapse)AuthorFilesLines
2009-04-07spi_imx: set spi_master.dma_alignment = 4Mike Rapoport1-0/+2
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07pxa2xx_spi: set spi_master.dma_alignment = 8Mike Rapoport1-0/+2
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi_bfin5xx: remove unused IS_DMA_ALIGNED macroMike Rapoport1-2/+0
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi: pxa2xx_spi: introduce chipselect GPIO to simplify the common casesEric Miao1-18/+78
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs for this. Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: David Brownell <david-b@pacbell.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi: limit reaches -1, tested 0Roel Kluin1-1/+2
With a postfix decrement limit will reach -1 rather than 0, so the warning will not be issued. Also, add a cpu_relax() into the busy-wait loop. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Mariusz Ceier <mceier@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: Make mmc_spi driver work on BlackfinWolfgang Muees1-142/+108
1. Rewrite of the non-dma data transfer functions to use only ONE mode of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX bit pattern. So the TDBR = 0xFFFF inside the read calls won't work. 2. Clear SPI_RDBR before reading and before duplex transfer. Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a lot of duplex transfers, this is the main cause of mmc_spi failure. 3. Poll RXS for transfer completion. Polling SPIF or TXS cannot guarantee transfer completion. This may interrupt a transfer before it is finished. Also this may leave garbage data in buffer and affect next transfer. [Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct bfin5xx_spi_chip" to specify the value to transmit if no TX value is supplied.] Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: Add GPIO controlled SPI Slave Select supportMichael Hennerich1-8/+32
Add support for GPIO controlled SPI Chip Selects. To make use of this feature, set chip_select = 0 and add a proper cs_gpio to your controller_data. struct spi_board_info .chip_select = 0 struct bfin5xx_spi_chip .cs_gpio = GPIO_P### There are various SPI devices that require SPI MODE_0, and need to have the Chip Selects asserted during the entire transfer. Consider using SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix NULL pointer crashMike Frysinger1-0/+3
Fix NULL pointer crash when cleaning up from invalid platform resources Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: use bfin_spi_ prefix on all functionsMike Frysinger1-111/+112
Do this because when things crash, we get simple names like "setup" and "start_queue" which is pretty difficult to trace back to the real thing: the spi driver Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_changeYi Li1-9/+8
According to comments in linux/spi/spi.h: * All SPI transfers start with the relevant chipselect active. Normally * it stays selected until after the last transfer in a message. Drivers * can affect the chipselect signal using cs_change. * * (i) If the transfer isn't the last one in the message, this flag is * used to make the chipselect briefly go inactive in the middle of the * message. Toggling chipselect in this way may be needed to terminate * a chip command, letting a single spi_message perform all of group of * chip transactions together. * * (ii) When the transfer is the last one in the message, the chip may * stay selected until the next transfer. On multi-device SPI busses * with nothing blocking messages going to other devices, this is just * a performance hint; starting a message to another device deselects * this one. But in other cases, this can be used to ensure correctness. * Some devices need protocol transactions to be built from a series of * spi_message submissions, where the content of one message is determined * by the results of previous messages and where the whole transaction * ends when the chipselect goes intactive. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix bug - spi controller driver does not ↵Yi Li1-3/+2
assert/deassert CS correctly This bug can be observed when two SPI devices are sharing the spi bus: One device is set as SPI CS 7, another one is using SPI CS 4. In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG register. From the debug bellow: cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7 cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4 When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however, SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode). Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7 is asserted, however SPISSEL4 will be asserted too (I can see this using the scope). This is unreasonable according to HRM. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: tweak magic spi dma sequence to get it working on BF54xMike Frysinger1-1/+2
Without this change, SPI DMA is not reliably under stress tests. Obiviously it's a hardware issue which is not addressed by any document. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: add timeout while waiting for SPIF in dma irq handlerMike Frysinger1-1/+11
The "while" endless loop will cause the system hang if hardware error, so we add timeout control to make the system alive. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: get dma working for SPI flashesMike Frysinger1-10/+16
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when enable_dma is disabled, but doesn't work at all when turning DMA on. We get just 0xff bytes back when trying to read the device. Change the code around so that it programs the SPI first and then enables DMA, it seems to work a lot better ... Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: SPI slave select code cleanupMike Frysinger1-3/+1
- remove duplicated definition MAX_SPI_SSEL - remove unnecessary array size Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: use the properl BIT_CTL_xxx definesMike Frysinger1-3/+3
use the properl BIT_CTL_... defines rather than the internal driv er CFG_SPI_... defines Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: do not check for SPI errors if DMA itself did not flag anyMike Frysinger1-1/+1
We only need to check SPI error when DMA failes, cause that is the DMA IRQ handling routine. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: add a few more DMA debug messagesMike Frysinger1-2/+10
Because of DMA hardware issue, we were trying to use software workaround. This patch add some useful debug messages to help us debugging the DMA code. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: drop bogus cast and touchup dma labelMike Frysinger1-2/+2
Blackfin's related DMA callback API doesn't need void * cast, so drop it. And this driver is for all Blackfin processors not only for BF53x, we update the DMA request label for more meaningful information. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: unify duplicated code in dma read/write pathsMike Frysinger1-26/+21
For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX and RX paths are almost the same. This patch unify the duplicated DMA code to make it more readable. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: pass DMA overflow error to the higher levelMike Frysinger1-5/+11
If the SPI bus registers a receive overflow error, pass the result back up to the higher levels. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: use len_in_bytes when we care about the number of bytes ↵Mike Frysinger1-3/+3
transferred Use len_in_bytes when we care about the number of bytes transferred rather than the number of spi transactions. (this value will be the same for 8bit transfers, but not any other sizes) Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: remove useless <asm/cplbinit.h>Mike Frysinger1-3/+0
We already moved bfin_addr_dcachable() and friends into the cacheflush header where it belongs, so don't need to include <asm/cplbinit.h> here. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: Fix erroneous SPI Clock divisor calculationMichael Hennerich1-0/+3
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always >= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the serial clock. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: ensure cache coherency before doing DMAVitja Makarov1-3/+20
Flush or invalidate caches before doing DMA transfer, if needed. [Mike Frysinger <vapier.adi@gmail.com>: add comment to address the issue "Full duplex only works for non-DMA transfers".] Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-02spi-gpio: allow operation without CS signalMichael Buesch1-8/+13
Change spi-gpio so that it is possible to drive SPI communications over GPIO without the need for a chipselect signal. This is useful in very small setups where there's only one slave device on the bus. This patch does not affect existing setups. I use this for a tiny communication channel between an embedded device and a microcontroller. There are not enough GPIOs available for chipselect and it's not needed anyway in this case. Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01spi_mpc83xx: add OF platform driver bindingsAnton Vorontsov1-36/+294
Implement full support for OF SPI bindings. Now the driver can manage its own chip selects without any help from the board files and/or fsl_soc constructors. The "legacy" code is well isolated and could be removed as time goes by. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01spi_mpc83xx: rework chip selects handlingAnton Vorontsov1-13/+7
The main purpose of this patch is to pass 'struct spi_device' to the chip select handling routines. This is needed so that we could implement full-fledged OpenFirmware support for this driver. While at it, also: - Replace two {de,activate}_cs routines by single cs_contol(). - Don't duplicate platform data callbacks in mpc83xx_spi struct. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01spi_mpc83xx: fix sparse warningsAnton Vorontsov1-7/+9
The patch fixes following sparse warnings: CHECK spi_mpc83xx.c spi_mpc83xx.c:145:1: warning: symbol 'mpc83xx_spi_rx_buf_u8' was not declared. Should it be static? spi_mpc83xx.c:146:1: warning: symbol 'mpc83xx_spi_rx_buf_u16' was not declared. Should it be static? spi_mpc83xx.c:147:1: warning: symbol 'mpc83xx_spi_rx_buf_u32' was not declared. Should it be static? spi_mpc83xx.c:148:1: warning: symbol 'mpc83xx_spi_tx_buf_u8' was not declared. Should it be static? spi_mpc83xx.c:149:1: warning: symbol 'mpc83xx_spi_tx_buf_u16' was not declared. Should it be static? spi_mpc83xx.c:150:1: warning: symbol 'mpc83xx_spi_tx_buf_u32' was not declared. Should it be static? spi_mpc83xx.c:175:32: warning: incorrect type in initializer (different address spaces) spi_mpc83xx.c:175:32: expected void *tmp_ptr spi_mpc83xx.c:175:32: got unsigned int [noderef] <asn:2>*<noident> spi_mpc83xx.c:183:26: warning: incorrect type in argument 1 (different address spaces) spi_mpc83xx.c:183:26: expected unsigned int [noderef] [usertype] <asn:2>*reg spi_mpc83xx.c:183:26: got void *tmp_ptr spi_mpc83xx.c:184:26: warning: incorrect type in argument 1 (different address spaces) spi_mpc83xx.c:184:26: expected unsigned int [noderef] [usertype] <asn:2>*reg spi_mpc83xx.c:184:26: got void *tmp_ptr spi_mpc83xx.c:287:31: warning: incorrect type in initializer (different address spaces) spi_mpc83xx.c:287:31: expected void *tmp_ptr spi_mpc83xx.c:287:31: got unsigned int [noderef] <asn:2>*<noident> spi_mpc83xx.c:295:25: warning: incorrect type in argument 1 (different address spaces) spi_mpc83xx.c:295:25: expected unsigned int [noderef] [usertype] <asn:2>*reg spi_mpc83xx.c:295:25: got void *tmp_ptr spi_mpc83xx.c:296:25: warning: incorrect type in argument 1 (different address spaces) spi_mpc83xx.c:296:25: expected unsigned int [noderef] [usertype] <asn:2>*reg spi_mpc83xx.c:296:25: got void *tmp_ptr spi_mpc83xx.c:486:13: warning: symbol 'mpc83xx_spi_irq' was not declared. Should it be static? Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-30Merge commit 'origin/master' into nextBenjamin Herrenschmidt11-31/+32
Manual merge of: arch/powerpc/include/asm/elf.h drivers/i2c/busses/i2c-mpc.c
2009-03-28Merge branch 'origin' into develRussell King11-23/+25
Conflicts: sound/soc/pxa/pxa2xx-i2s.c
2009-03-24spi: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers11-23/+25
Cc: dbrownell@users.sourceforge.net Cc: spi-devel-general@lists.sourceforge.net Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
2009-03-19Merge branch 'omap-clks3' into develRussell King2-6/+7
Conflicts: arch/arm/mach-omap2/clock.c
2009-03-13Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into develRussell King1-1/+1
Conflicts: arch/arm/mach-at91/gpio.c
2009-03-11powerpc/virtex/spi: Xilinx SPI driver not releasing memoryJohn Linn1-2/+7
The driver was not releasing memory when it was removed or when there was a failure during probe. This fixes it. Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-03-09[ARM] pxa: move DMA registers definitions into <mach/dma.h>Eric Miao1-2/+0
1. Driver code where pxa_request_dma() is called will most likely reference DMA registers as well, and it is really unnecessary to include pxa-regs.h just for this. Move the definitions into <mach/dma.h> and make relevant drivers include it instead of <mach/pxa-regs.h>. 2. Introduce DMAC_REGS_VIRT as the virtual address base for these DMA registers. This allows later processors to re-use the same IP while registers may start at different I/O address. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-02-18spi-gpio: sanitize MISO bitvalueMichael Buesch1-1/+1
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1. Sanitize the value to a 0/1 boolean. Signed-off-by: Michael Buesch <mb@bu3sch.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-08[ARM] omap: spi: arrange for omap_uwire to use connection IDRussell King1-4/+5
... which now means no driver requests the "armxor_ck" clock directly. Also, fix the error handling for clk_get(), ensuring that we propagate the error returned from clk_get(). Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-08[ARM] omap: mcspi: new short connection id namesRussell King1-2/+2
... rather than the clock names themselves. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-01-26spi: Move at25 (for SPI eeproms) to /drivers/misc/eepromWolfram Sang3-401/+0
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15atmel_spi: allow transfer when max_speed_hz = 0Stanislaw Gruszka1-2/+1
For some reason I have to slowdown clock to touchscreen device. In atmel_spi_setup() there is comment that max_speed_hz == 0 means as slow as possible and divider is set to maximum value. But in atmel_spi_transfer() function is check against not zero max_speed_hz with EINVAL returned. Probably driver should setup divider for each transfer based on transfer->speed_hz value, but I think that would be not necessary overhead as all used devices have constant clock. Below patch works fine for me. Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-09Xilinx: SPI: updated driver for device treeJohn Linn1-56/+81
The driver was updated to use the device tree rather than the platform data. Signed-off-by: John Linn <john.linn@xilinx.com>
2009-01-07hwmon: (lm70) Code streamlining and cleanupKaiwan N Billimoria1-21/+12
This fixes a byteswap bug in the LM70 temperature sensor driver, which was previously covered up by a converse bug in the driver for the LM70EVAL-LLP board (which is also fixed). Other fixes: doc updates, remove an annoying msleep(), and improve three-wire protocol handling. Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com> [ dbrownell@users.sourceforge.net: doc and whitespace tweaks ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds4-14/+12
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (60 commits) uio: make uio_info's name and version const UIO: Documentation for UIO ioport info handling UIO: Pass information about ioports to userspace (V2) UIO: uio_pdrv_genirq: allow custom irq_flags UIO: use pci_ioremap_bar() in drivers/uio arm: struct device - replace bus_id with dev_name(), dev_set_name() libata: struct device - replace bus_id with dev_name(), dev_set_name() avr: struct device - replace bus_id with dev_name(), dev_set_name() block: struct device - replace bus_id with dev_name(), dev_set_name() chris: struct device - replace bus_id with dev_name(), dev_set_name() dmi: struct device - replace bus_id with dev_name(), dev_set_name() gadget: struct device - replace bus_id with dev_name(), dev_set_name() gpio: struct device - replace bus_id with dev_name(), dev_set_name() gpu: struct device - replace bus_id with dev_name(), dev_set_name() hwmon: struct device - replace bus_id with dev_name(), dev_set_name() i2o: struct device - replace bus_id with dev_name(), dev_set_name() IA64: struct device - replace bus_id with dev_name(), dev_set_name() i7300_idle: struct device - replace bus_id with dev_name(), dev_set_name() infiniband: struct device - replace bus_id with dev_name(), dev_set_name() ISDN: struct device - replace bus_id with dev_name(), dev_set_name() ...
2009-01-06drivers/spi: move a dereference below a NULL testJulia Lawall1-1/+2
In each case, if the NULL test is necessary, then the dereference should be moved below the NULL test. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ type T; expression E; identifier i,fld; statement S; @@ - T i = E->fld; + T i; ... when != E when != i if (E == NULL) S + i = E->fld; // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06spi: use generic gpio calls in spi_s3c24xx_gpioBen Dooks1-9/+29
Change the spi_s3c2410 driver to use the generic gpio calls that are now available. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06spi: atmel_spi update chipselect handlingHaavard Skinnemoen1-26/+67
This solves several issues: * It fixes the wrong idle clock polarity issue in a cleaner and less expensive way. * It handles the AT32AP7000 errata "SPI Chip Select 0 BITS field overrides other Chip Selects". Other chips, e.g. AT91SAM9261, have similar issues. Currently, the AT91RM9200 code path is left alone. But it might be interesting to try the same technique on RM9200 using a different CSR register. [dbrownell@users.sourceforge.net: restore debug message for activation] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06atmel_spi: clean up SPIv1 quirk handlingHaavard Skinnemoen1-18/+22
Currently, we have a flag called "new_1" which is basically equivalent to cpu_is_at91rm9200(). The latter is also called directly a few places. Clean up this mess by introducing a atmel_spi_v2() function for determining the controller version, and move all version dependent code over to use it. This allows us to remove the new_1 flag. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06spi_gpio driverDavid Brownell3-1/+378
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as "spi_gpio", so it works with arbitrary GPIOs and can be configured through platform_data. Such SPI masters support: - any number of bus instances (bus_num is the platform_device.id) - any number of chipselects (one GPIO per spi_device) - all four SPI_MODE values, and SPI_CS_HIGH - i/o word sizes from 1 to 32 bits; - devices configured as with any other spi_master controller When configured using platform_data, this provides relatively low clock rates. On platforms that support inlined GPIO calls, significantly improved transfer speeds are also possible with a semi-custom driver. (It's still painful when accessing flash memory, but less so.) Sanity checked by using this version to replace both native controllers on a board with six different SPI slaves, relying on three different SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation. [akpm@linux-foundation.org: cleanups] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Magnus Damm <damm@igel.co.jp> Tested-by: Magnus Damm <damm@igel.co.jp> Cc: Torgil Svensson <torgil.svensson@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06spi: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers4-14/+12
Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 23:48:04 +0000