| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit
e0f9956a3862 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10fd ("net: stmmac: Add support for VLAN promiscuous mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9131RNX incorrectly shows EEE capabilities in its registers.
Although the "EEE control and capability 1" (Register 3.20) is set to 0,
indicating no EEE support, the "EEE advertisement 1" (Register 7.60) is
set to 0x6, advertising EEE support for 1000BaseT/Full and
100BaseT/Full.
This inconsistency causes PHYlib to assume there is no EEE support,
preventing control over EEE advertisement, which is enabled by default.
This patch resolves the issue by utilizing the ksz9477_get_features()
function to correctly set the EEE capabilities for the KSZ9131RNX. This
adjustment allows proper control over EEE advertisement and ensures
accurate representation of the device's capabilities.
Fixes: 8b68710a3121 ("net: phy: start using genphy_c45_ethtool_get/set_eee()")
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fwnode_get_phy_node() does not motify the fwnode structure, so make
the argument const,
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constify sfp-bus internal fwnode uses, since we do not modify the
fwnode structures.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sfp_bus_find_fwnode() does not write to the fwnode, so let's make it
const.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The failover txq is inited as 16 queues.
when a packet is transmitted from the failover device firstly,
the failover device will select the queue which is returned from
the primary device if the primary device is UP and running.
If the primary device txq is bigger than the default 16,
it can lead to the following warning:
eth0 selects TX queue 18, but real number of TX queues is 16
The warning backtrace is:
[ 32.146376] CPU: 18 PID: 9134 Comm: chronyd Tainted: G E 6.2.8-1.el7.centos.x86_64 #1
[ 32.147175] Hardware name: Red Hat KVM, BIOS 1.10.2-3.el7_4.1 04/01/2014
[ 32.147730] Call Trace:
[ 32.147971] <TASK>
[ 32.148183] dump_stack_lvl+0x48/0x70
[ 32.148514] dump_stack+0x10/0x20
[ 32.148820] netdev_core_pick_tx+0xb1/0xe0
[ 32.149180] __dev_queue_xmit+0x529/0xcf0
[ 32.149533] ? __check_object_size.part.0+0x21c/0x2c0
[ 32.149967] ip_finish_output2+0x278/0x560
[ 32.150327] __ip_finish_output+0x1fe/0x2f0
[ 32.150690] ip_finish_output+0x2a/0xd0
[ 32.151032] ip_output+0x7a/0x110
[ 32.151337] ? __pfx_ip_finish_output+0x10/0x10
[ 32.151733] ip_local_out+0x5e/0x70
[ 32.152054] ip_send_skb+0x19/0x50
[ 32.152366] udp_send_skb.isra.0+0x163/0x3a0
[ 32.152736] udp_sendmsg+0xba8/0xec0
[ 32.153060] ? __folio_memcg_unlock+0x25/0x60
[ 32.153445] ? __pfx_ip_generic_getfrag+0x10/0x10
[ 32.153854] ? sock_has_perm+0x85/0xa0
[ 32.154190] inet_sendmsg+0x6d/0x80
[ 32.154508] ? inet_sendmsg+0x6d/0x80
[ 32.154838] sock_sendmsg+0x62/0x70
[ 32.155152] ____sys_sendmsg+0x134/0x290
[ 32.155499] ___sys_sendmsg+0x81/0xc0
[ 32.155828] ? _get_random_bytes.part.0+0x79/0x1a0
[ 32.156240] ? ip4_datagram_release_cb+0x5f/0x1e0
[ 32.156649] ? get_random_u16+0x69/0xf0
[ 32.156989] ? __fget_light+0xcf/0x110
[ 32.157326] __sys_sendmmsg+0xc4/0x210
[ 32.157657] ? __sys_connect+0xb7/0xe0
[ 32.157995] ? __audit_syscall_entry+0xce/0x140
[ 32.158388] ? syscall_trace_enter.isra.0+0x12c/0x1a0
[ 32.158820] __x64_sys_sendmmsg+0x24/0x30
[ 32.159171] do_syscall_64+0x38/0x90
[ 32.159493] entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fix that by reducing txq number as the non-existent primary-dev does.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver")
Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
empty dynamic MAC table.
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e6e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, vmxnet3 uses GRO callback only if LRO is disabled. However,
on smartNic based setups where UPT is supported, LRO can be enabled
from guest VM but UPT devicve does not support LRO as of now. In such
cases, there can be performance degradation as GRO is not being done.
This patch fixes this issue by calling GRO API when UPT is enabled. We
use updateRxProd to determine if UPT mode is active or not.
To clarify few things discussed over the thread:
The patch is not neglecting any feature bits nor disabling GRO. It uses
GRO callback when UPT is active as LRO is not available in UPT.
GRO callback cannot be used as default for all cases as it degrades
performance for non-UPT cases or for cases when LRO is already done in
ESXi.
Cc: stable@vger.kernel.org
Fixes: 6f91f4ba046e ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323200721.27622-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe284 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At NIC reset, some offload features related to encapsulated traffic
might have changed (this mainly happens if the firmware-variant is
changed with the sfboot userspace tool). Because of this, features are
checked and set again at reset time.
However, this was not done right, and some features were improperly
overwritten at NIC reset:
- Tunneled IPv6 segmentation was always disabled
- Features disabled with ethtool were reenabled
- Features that becomes unsupported after the reset were not disabled
Also, checking if the device supports IPV6_CSUM to enable TSO6 is no
longer necessary because all currently supported devices support it.
Additionally, move the assignment of some other features to the
EF10_OFFLOAD_FEATURES macro, like it is done in ef100, leaving the
selection of features in efx_pci_probe_post_io a bit cleaner.
Fixes: ffffd2454a7a ("sfc: correctly advertise tunneled IPv6 segmentation")
Fixes: 24b2c3751aa3 ("sfc: advertise encapsulated offloads on EF10")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Suggested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Tested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230323083417.7345-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is 64-bit interrupt cause register for txgbe. Fix to clear upper
32 bits.
Fixes: 3f703186113f ("net: libwx: Add irq flow functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230322103632.132011-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-03-23
We've added 8 non-merge commits during the last 13 day(s) which contain
a total of 21 files changed, 238 insertions(+), 161 deletions(-).
The main changes are:
1) Fix verification issues in some BPF programs due to their stack usage
patterns, from Eduard Zingerman.
2) Fix to add missing overflow checks in xdp_umem_reg and return an error
in such case, from Kal Conley.
3) Fix and undo poisoning of strlcpy in libbpf given it broke builds for
libcs which provided the former like uClibc-ng, from Jesus Sanchez-Palencia.
4) Fix insufficient bpf_jit_limit default to avoid users running into hard
to debug seccomp BPF errors, from Daniel Borkmann.
5) Fix driver return code when they don't support a bpf_xdp_metadata kfunc
to make it unambiguous from other errors, from Jesper Dangaard Brouer.
6) Two BPF selftest fixes to address compilation errors from recent changes
in kernel structures, from Alexei Starovoitov.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xdp: bpf_xdp_metadata use EOPNOTSUPP for no driver support
bpf: Adjust insufficient default bpf_jit_limit
xsk: Add missing overflow check in xdp_umem_reg
selftests/bpf: Fix progs/test_deny_namespace.c issues.
selftests/bpf: Fix progs/find_vma_fail1.c build error.
libbpf: Revert poisoning of strlcpy
selftests/bpf: Tests for uninitialized stack reads
bpf: Allow reads from uninit stack
====================
Link: https://lore.kernel.org/r/20230323225221.6082-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.3
Third set of fixes for v6.3. mt76 has two kernel crash fixes and
adding back 160 MHz channel support for mt7915. mac80211 has fixes for
a race in transmit path and two mesh related fixes. iwlwifi also has
fixes for races.
* tag 'wireless-2023-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix mesh path discovery based on unicast packets
wifi: mac80211: fix qos on mesh interfaces
wifi: iwlwifi: mvm: protect TXQ list manipulation
wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
wifi: mac80211: Serialize ieee80211_handle_wake_tx_queue()
wifi: mwifiex: mark OF related data as maybe unused
wifi: mt76: connac: do not check WED status for non-mmio devices
wifi: mt76: mt7915: add back 160MHz channel width support for MT7915
wifi: mt76: do not run mt76_unregister_device() on unregistered hw
====================
Link: https://lore.kernel.org/r/20230323110332.C4FE4C433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-03-21
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: E-Switch, Fix an Oops in error handling code
net/mlx5: Read the TC mapping of all priorities on ETS query
net/mlx5e: Overcome slow response for first macsec ASO WQE
net/mlx5e: Initialize link speed to zero
net/mlx5: Fix steering rules cleanup
net/mlx5e: Block entering switchdev mode with ns inconsistency
net/mlx5e: Set uplink rep as NETNS_LOCAL
====================
Link: https://lore.kernel.org/r/20230321211135.47711-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (ice)
This series contains updates to ice driver only.
Piotr sets first_desc field for proper handling of Flow Director
packets.
Michal moves error checking for VF earlier in function to properly return
error before other checks/reporting; he also corrects VSI filter removal to
be done during VSI removal and not rebuild.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: remove filters only if VSI is deleted
ice: check if VF exists before mode check
ice: fix rx buffers handling for flow director packets
====================
Link: https://lore.kernel.org/r/20230321183641.2849726-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (iavf, i40e)
This series contains updates to iavf and i40e drivers.
Stefan Assmann adds check, and return, if driver has already gone
through remove to prevent hang for iavf.
Radoslaw adds zero initialization to ensure Flow Director packets are
populated with correct values for i40e.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix flow director packet filter programming
iavf: fix hang on reboot with ice
====================
Link: https://lore.kernel.org/r/20230321183548.2849671-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move setting the ssc_delta variable to under the PHY_INTERFACE_MODE_TRGMII
case as it's only needed when trgmii is used.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-3-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move lowering the TRGMII Tx clock driving to mt7530_setup(), after setting
the core clock, as seen on the U-Boot MediaTek ethernet driver.
Move the code which looks like it lowers the TRGMII Rx clock driving to
after the TRGMII Tx clock driving is lowered. This is run after lowering
the Tx clock driving on the U-Boot MediaTek ethernet driver as well.
This way, the switch should consume less power regardless of port 6 being
used.
Update the comment explaining mt7530_pad_clk_setup().
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: https://source.denx.de/u-boot/u-boot/-/blob/29a48bf9ccba45a5e560bb564bbe76e42629325f/drivers/net/mtk_eth.c#L682
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Split the code that enables and disables TRGMII clocks and core clock.
Move enabling and disabling core clock to mt7530_pll_setup() as it's
supposed to be run there.
Add 20 ms delay before enabling the core clock as seen on the U-Boot
MediaTek ethernet driver.
Change the comment for enabling and disabling TRGMII clocks as the code
seems to affect both TXC and RXC.
Tested rgmii and trgmii modes of port 6 and rgmii mode of port 5 on MCM
MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI
Bananapi BPI-R2.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Link: https://source.denx.de/u-boot/u-boot/-/blob/29a48bf9ccba45a5e560bb564bbe76e42629325f/drivers/net/mtk_eth.c#L589
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230320190520.124513-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"modprobe asix ; rmmod asix ; modprobe asix" fails with:
sysfs: cannot create duplicate filename \
'/devices/virtual/mdio_bus/usb-003:004'
Issue was originally reported by Anton Lundin on 2022-06-22 (link below).
Chrome OS team hit the same issue in Feb, 2023 when trying to find
work arounds for other issues with AX88172 devices.
The use of devm_mdiobus_register() with usbnet devices results in the
MDIO data being associated with the USB device. When the asix driver
is unloaded, the USB device continues to exist and the corresponding
"mdiobus_unregister()" is NOT called until the USB device is unplugged
or unauthorized. So the next "modprobe asix" will fail because the MDIO
phy sysfs attributes still exist.
The 'easy' (from a design PoV) fix is to use the non-devm variants of
mdiobus_* functions and explicitly manage this use in the asix_bind
and asix_unbind function calls. I've not explored trying to fix usbnet
initialization so devm_* stuff will work.
Fixes: e532a096be0e5 ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/netdev/20220623063649.GD23685@pengutronix.de/T/
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20230321170539.732147-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The link speed is never changed for the uptime of a VM, and the current
implementation sends an admin queue command for each call. Admin queue
command invocations have nontrivial overhead (e.g., VM exits), which can
be disruptive to users if triggered frequently. Our telemetry data shows
that there are VMs that make frequent calls to this admin queue command.
Caching the result of the original admin queue command would eliminate
the need to send multiple admin queue commands on subsequent calls to
retrieve link speed.
Fixes: 7e074d5a76ca ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321172332.91678-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running "ethtool -S eno0 --groups rmon" without an explicit "--src
emac|pmac" argument, the kernel will not report
rx-rmon-etherStatsPkts64to64Octets, rx-rmon-etherStatsPkts65to127Octets,
etc. This is because on ETHTOOL_MAC_STATS_SRC_AGGREGATE, we do not
populate the "ranges" argument.
ocelot_port_get_rmon_stats() does things differently and things work
there. I had forgotten to make sure that the code is structured the same
way in both drivers, so do that now.
Fixes: cf52bd238b75 ("net: enetc: add support for MAC Merge statistics counters")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321232831.1200905-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When driver doesn't implement a bpf_xdp_metadata kfunc the fallback
implementation returns EOPNOTSUPP, which indicate device driver doesn't
implement this kfunc.
Currently many drivers also return EOPNOTSUPP when the hint isn't
available, which is ambiguous from an API point of view. Instead
change drivers to return ENODATA in these cases.
There can be natural cases why a driver doesn't provide any hardware
info for a specific hint, even on a frame to frame basis (e.g. PTP).
Lets keep these cases as separate return codes.
When describing the return values, adjust the function kernel-doc layout
to get proper rendering for the return values.
Fixes: ab46182d0dcb ("net/mlx4_en: Support RX XDP metadata")
Fixes: bc8d405b1ba9 ("net/mlx5e: Support RX XDP metadata")
Fixes: 306531f0249f ("veth: Support RX XDP metadata")
Fixes: 3d76a4d3d4e5 ("bpf: XDP metadata RX kfuncs")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/167940675120.2718408.8176058626864184420.stgit@firesoul
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Local port is a 10-bit number, but it was mistakenly stored in a u8,
resulting in firmware errors when using a netdev corresponding to a
local port higher than 255.
Fix by storing the local port in u16, as is done in the rest of the
code.
Fixes: bf73904f5fba ("mlxsw: Add support for 802.1Q FID family")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/eace1f9d96545ab8a2775db857cb7e291a9b166b.1679398549.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The DMA address returned by dma_map_single() should be checked with
dma_mapping_error(). Fix it accordingly.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6645a4b5c1e364312103f48b7b36783b94e197a2.1679370343.git.fthain@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lack of a definition for this counter is what initially prompted me
to investigate a problem which really manifested itself as the previous
change, "net: mscc: ocelot: fix transfer from region->buf to ocelot->stats".
When TX_MM_HOLD is defined in enum ocelot_stat but not in struct
ocelot_stat_layout ocelot_mm_stats_layout, this creates a hole, which
due to the aforementioned bug, makes all counters following TX_MM_HOLD
be recorded off by one compared to their correct position. So for
example, a non-zero TX_PMAC_OCTETS would be reported as TX_MERGE_FRAGMENTS,
TX_PMAC_UNICAST would be reported as TX_PMAC_OCTETS, TX_PMAC_64 would be
reported as TX_PMAC_PAUSE, etc etc. This is because the size of the hole
(1) is much smaller than the size of the region, so the phenomenon where
the stats are off-by-one, rather than lost, prevails.
However, the phenomenon where stats are lost can be seen too, for
example with DROP_LOCAL, which is at the beginning of its own region
(offset 0x000400 vs the previous 0x0002b0 constitutes a discontinuity).
This is also reported as off by one and saved to TX_PMAC_1527_MAX, but
that counter is not reported to the unstructured "ethtool -S", as
opposed to DROP_LOCAL which is (as "drop_local").
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To understand the problem, we need some definitions.
The driver is aware of multiple counters (enum ocelot_stat), yet not all
switches supported by the driver implement all counters. There are 2
statistics layouts: ocelot_stats_layout and ocelot_mm_stats_layout, the
latter having 36 counters more than the former.
ocelot->stats[] is not a compact array, i.e. there are elements within
it which are not going to be populated for ocelot_stats_layout. On the
other hand, ocelot->stats[] is easily indexable, for example "tx_octets"
for port 3 can be found at ocelot->stats[3 * OCELOT_NUM_STATS +
OCELOT_STAT_TX_OCTETS], and that is why we keep it sparse.
Regions, as created by ocelot_prepare_stats_regions(), are compact
(every element from region->buf will correspond to a counter that is
present in this switch's layout) but are not easily indexable.
Let's define holes as the ranges of values of enum ocelot_stat for which
ocelot_stats_layout doesn't have a "reg" defined. For example, there is
a hole between OCELOT_STAT_RX_GREEN_PRIO_7 and OCELOT_STAT_TX_OCTETS
which is of 23 elements that are only present on ocelot_mm_stats_layout,
and as such, they are also present in enum ocelot_stat. Let's define the
left extremity of the hole - the last enum ocelot_stat still defined -
as A (in this case OCELOT_STAT_RX_GREEN_PRIO_7) and the right extremity -
the first enum ocelot_stat that is defined after a series of undefined
ones - as B (in this case OCELOT_STAT_TX_OCTETS).
There is a bug in the procedure which transfers stats from region->buf[]
to ocelot->stats[].
For each hole in the ocelot_stats_layout, the logic transfers the stats
starting with enum ocelot_stat B to ocelot->stats[] index A + 1. So all
stats after a hole are saved to a position which is off by B - A + 1
elements.
This causes 2 kinds of issues:
(a) counters which shouldn't increment increment
(b) counters which should increment don't
Holes in the ocelot_stat_layout automatically imply the end of a region
and the beginning of a new one; however the reverse is not necessarily
true. For example, for ocelot_mm_stat_layout, there could be multiple
regions (which indicate discontinuities in register addresses) while
there is no hole (which indicates discontinuities in enum ocelot_stat
values).
In the example above, the stats from the second region->buf[] are not
transferred to ocelot->stats starting with index
"port * OCELOT_NUM_STATS + OCELOT_STAT_TX_OCTETS" as they should, but
rather, starting with element
"port * OCELOT_NUM_STATS + OCELOT_STAT_RX_GREEN_PRIO_7 + 1".
That stats[] array element is not reported to user space for switches
that use ocelot_stat_layout, and that is how issue (b) occurs.
However, if the length of the second region is larger than the hole,
then some stats will start to be transferred to the ocelot->stats[]
indices which *are* reported to user space, but those indices contain
wrong values (corresponding to unexpected counters). This is how issue
(a) occurs.
The procedure, as it was introduced in commit d87b1c08f38a ("net: mscc:
ocelot: use bulk reads for stats"), was not buggy, because there were no
holes in the struct ocelot_stat_layout instances at that time. The
problem is that when those holes were introduced, the function was not
updated to take them into consideration.
To update the procedure, we need to know, for each region, which enum
ocelot_stat corresponds to its region->base. We have no way of deducing
that based on the contents of struct ocelot_stats_region, so we need to
add this information.
Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit changed struct ocelot_stat_layout :: "u32 offset" to
"u32 reg".
However, "u32 reg" is not quite a register address, but an enum
ocelot_reg, which in itself encodes an enum ocelot_target target in the
upper bits, and an index into the ocelot->map[target][] array in the
lower bits.
So, whereas the previous code comparison between stats_layout[i].offset
and last + 1 was correct (because those "offsets" at the time were
32-bit relative addresses), the new code, comparing layout[i].reg to
last + 4 is not correct, because the "reg" here is an enum/index, not an
actual register address.
What we want to compare are indeed register addresses, but to do that,
we need to actually go through the same motions as
__ocelot_bulk_read_ix() itself.
With this bug, all statistics counters are deemed by
ocelot_prepare_stats_regions() as constituting their own region.
(Truncated) log on VSC9959 (Felix) below (prints added by me):
Before:
region of 1 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x001]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x002]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x041]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x042]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x081]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x0ac]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x100]
region of 1 contiguous counters starting with SYS:STAT:CNT[0x101]
...
region of 1 contiguous counters starting with SYS:STAT:CNT[0x111]
After:
region of 67 contiguous counters starting with SYS:STAT:CNT[0x000]
region of 45 contiguous counters starting with SYS:STAT:CNT[0x080]
region of 18 contiguous counters starting with SYS:STAT:CNT[0x100]
Since commit d87b1c08f38a ("net: mscc: ocelot: use bulk reads for
stats") intended bulking as a performance improvement, and since now,
with trivial-sized regions, performance is even worse than without
bulking at all, this could easily qualify as a performance regression.
Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The error handling dereferences "vport". There is nothing we can do if
it is an error pointer except returning the error code.
Fixes: 133dcfc577ea ("net/mlx5: E-Switch, Alloc and free unique metadata for match")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When ETS configurations are queried by the user to get the mapping
assignment between packet priority and traffic class, only priorities up
to maximum TCs are queried from QTCT register in FW to retrieve their
assigned TC, leaving the rest of the priorities mapped to the default
TC #0 which might be misleading.
Fix by querying the TC mapping of all priorities on each ETS query,
regardless of the maximum number of TCs configured in FW.
Fixes: 820c2c5e773d ("net/mlx5e: Read ETS settings directly from firmware")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
First ASO WQE poll causes a cache miss in hardware hence the resut is
delayed. It causes to the situation where such WQE is polled earlier
than it is needed.
Add logic to retry ASO CQ polling operation.
Fixes: 739cfa34518e ("net/mlx5: Make ASO poll CQ usable in atomic context")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5e_port_max_linkspeed does not guarantee value assignment for speed.
Avoid cases where link_speed might be used uninitialized. In case
mlx5e_port_max_linkspeed fails, a default link speed of 50000 will be
used for the calculations.
Fixes: 3f6d08d196b2 ("net/mlx5e: Add RSS support for hairpin")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
vport's mc, uc and multicast rules are not deleted in teardown path when
EEH happens. Since the vport's promisc settings(uc, mc and all) in
firmware are reset after EEH, mlx5 driver will try to delete the above
rules in the initialization path. This cause kernel crash because these
software rules are no longer valid.
Fix by nullifying these rules right after delete to avoid accessing any dangling
pointers.
Call Trace:
__list_del_entry_valid+0xcc/0x100 (unreliable)
tree_put_node+0xf4/0x1b0 [mlx5_core]
tree_remove_node+0x30/0x70 [mlx5_core]
mlx5_del_flow_rules+0x14c/0x1f0 [mlx5_core]
esw_apply_vport_rx_mode+0x10c/0x200 [mlx5_core]
esw_update_vport_rx_mode+0xb4/0x180 [mlx5_core]
esw_vport_change_handle_locked+0x1ec/0x230 [mlx5_core]
esw_enable_vport+0x130/0x260 [mlx5_core]
mlx5_eswitch_enable_sriov+0x2a0/0x2f0 [mlx5_core]
mlx5_device_enable_sriov+0x74/0x440 [mlx5_core]
mlx5_load_one+0x114c/0x1550 [mlx5_core]
mlx5_pci_resume+0x68/0xf0 [mlx5_core]
eeh_report_resume+0x1a4/0x230
eeh_pe_dev_traverse+0x98/0x170
eeh_handle_normal_event+0x3e4/0x640
eeh_handle_event+0x4c/0x370
eeh_event_handler+0x14c/0x210
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0x84
Fixes: a35f71f27a61 ("net/mlx5: E-Switch, Implement promiscuous rx modes vf request handling")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Upon entering switchdev mode, VF/SF representors are spawned in the
devlink instance's net namespace, whereas the PF net device transforms
into the uplink representor, remaining in the net namespace the PF net
device was in. Therefore, if a PF net device's namespace is different from
its parent devlink net namespace, entering switchdev mode can create an
illegal situation where all representors sharing the same core device
are NOT in the same net namespace.
To avoid this issue, block entering switchdev mode for devices whose child
netdev net namespace has diverged from the parent devlink's.
Fixes: 7768d1971de6 ("net/mlx5: E-Switch, Add control for encapsulation")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Previously, NETNS_LOCAL was not set for uplink representors, inconsistent
with VF representors, and allowed the uplink representor to be moved
between net namespaces and separated from the VF representors it shares
the core device with. Such usage would break the isolation model of
namespaces, as devices in different namespaces would have access to
shared memory.
To solve this issue, set NETNS_LOCAL for uplink representors if eswitch is
in switchdev mode.
Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Initialize to zero structures to build a valid
Tx Packet used for the filter programming.
Fixes: a9219b332f52 ("i40e: VLAN field for flow director")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a system with E810 with existing VFs gets rebooted the following
hang may be observed.
Pid 1 is hung in iavf_remove(), part of a network driver:
PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow"
#0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb
#1 [ffffaad04005fae8] schedule at ffffffff8b323e2d
#2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc
#3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930
#4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf]
#5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513
#6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa
#7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc
#8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e
#9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429
#10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4
#11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice]
#12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice]
#13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice]
#14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1
#15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386
#16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870
#17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6
#18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159
#19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc
#20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d
#21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169
#22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b
RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7
RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90
R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005
R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000
ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b
During reboot all drivers PM shutdown callbacks are invoked.
In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE.
In ice_shutdown() the call chain above is executed, which at some point
calls iavf_remove(). However iavf_remove() expects the VF to be in one
of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If
that's not the case it sleeps forever.
So if iavf_shutdown() gets invoked before iavf_remove() the system will
hang indefinitely because the adapter is already in state __IAVF_REMOVE.
Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE,
as we already went through iavf_shutdown().
Fixes: 974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
Fixes: a8417330f8a5 ("iavf: Fix race condition between iavf_shutdown and iavf_remove")
Reported-by: Marius Cornea <mcornea@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Filters shouldn't be removed in VSI rebuild path. Removing them on PF
VSI results in no rule for PF MAC after changing for example queues
amount.
Remove all filters only in the VSI remove flow. As unload should also
cause the filter to be removed introduce, a new function ice_stop_eth().
It will unroll ice_start_eth(), so remove filters and close VSI.
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Setting trust on VF should return EINVAL when there is no VF. Move
checking for switchdev mode after checking if VF exists.
Fixes: c54d209c78b8 ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Kalyan Kodamagula <kalyan.kodamagula@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
