| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Update Copyright notices to 2013.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
No HCMD can be sent while RFKILL is asserted. If a SYNC
command is running while RFKILL is asserted the fw will
silently discard it. This means that the driver needs to
wake the process that sleeps on the CMD_SYNC.
Since the RFKILL interrupt is handled in the transport layer
and the code that sleeps in CMD_SYNC is also in the transport
layer, all this logic can be handled there.
This simplifies the work of the op_mode.
So the transport layer will now return -ERFKILL when a CMD
is sent and RFKILL is asserted. This will be the case even
when the CMD is SYNC. The transport layer will return
-ERFKILL straight away.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove this dead code, it is unused for device newer than
4965.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iwl-test flows were based on the cfg80211 testmode APIs.
To remove this coupling, the op mode (during the initialization
of the iwl_test object) is responsible to set the callbacks that
should be used by iwl-test to allocate skbs for events and replies
and to send events and replies.
The current op modes implement these callbacks based on the cfg80211
testmode APIs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Create an object that will enacpsulate the testmode functionality
that is common to all op modes.
* Copy definitions from dvm/dev.h
* Copy the testmode logic from dvm/testmode.c
* Link iwl-test object into the iwlwifi module
* Modify DVM to use iwl-test object
Reviewed-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The EEPROM reading/parsing code is all mixed in
the driver today, and the EEPROM is parsed only
when we access data from it. This is problematic
because the NVM needs to be parsed and that is
independent of reading it. Also, the NVM format
for new devices will be different and probably
require a new parser.
Therefore refactor the reading and parsing and
create two independent components. Reading the
EEPROM requires direct hardware accesses and
therefore access to the transport, but parsing
is independent and can be done on an NVM blob.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since we're working on another mode/driver
inside iwlwifi, move the current one into a
subdirectory to more cleanly separate the
code. While at it, rename all the files.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
