summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath9k
AgeCommit message (Collapse)AuthorFilesLines
2011-12-02Merge branch 'master' of ↵John W. Linville1-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/iwlwifi/iwl-agn.c drivers/net/wireless/libertas/cfg.c
2011-11-30ath9k_hw: add default chainmask for AR9462Mohammed Shafi Shajakhan1-0/+2
the default tx/rx chainmask for AR9462 is 0x3. this patch helps to assign 0x3 rather than 0x7 for AR9462 with the help of fix_chainmask module if something goes wrong in reading tx/rx chain mask from OTP/EEPROM card(though its very unlikely) Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: Fix TX IQ calibration for AR9003Mohammed Shafi Shajakhan1-1/+1
only for AR9485 (or) later chipsets TxIQ calibration runs as part of AGC calibration. without this patch TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed for AR9003 Reviewed-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: minor cleanupMohammed Shafi Shajakhan1-1/+0
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: fix a typoMohammed Shafi Shajakhan1-1/+1
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: MCI state machine based on MCI interruptMohammed Shafi Shajakhan5-1/+359
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: Add MCI related changes in chip resetMohammed Shafi Shajakhan1-0/+132
here we check for BT state and if BT calibration has started, give 25ms for BT Calibration to finish. we also take care of 2G/5G switch and LNA transfer incase WLAN is operating in 5G. in case the BT state is awake when we do WLAN calibration re-calibrate and we reset the message exchange between WLAN and BT. BT is given preference when simultaneous CAL request happens. calibration for WLAN/BT is done assuming that the other co-existing module is in awake state, if not we continue to do calibration while if the other module's state changes we need to do restart the calibration handshake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: Add support for MCI WLAN calibrationMohammed Shafi Shajakhan1-0/+43
WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ, waits for BT_CAL_GRANT. This is done with the help of GPM messages. also WLAN_CAL_DONE messages is sent once WLAN calibration is done. Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: MCI related changes in set_reset_regMohammed Shafi Shajakhan1-3/+11
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: MCI related changes in chip managementMohammed Shafi Shajakhan2-0/+26
send halt BT GPM if the chip is in network sleep and BT state is awake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: Add functions to allocate/free buffers for MCIMohammed Shafi Shajakhan3-0/+81
required buffers and dma allocation is done for GPM and SCHED messages Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: add MCI specific definitions and structuresMohammed Shafi Shajakhan1-0/+17
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: check for MCI interrupt in get_isrMohammed Shafi Shajakhan1-2/+34
check for the condition of MCI interrupt being triggered and appropriately obtain the values of MCI_INTERRUPT_RX_MSG_RAW and MCI_INTERRUPT_RAW Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: check for asynchronous MCI interrupt pendingMohammed Shafi Shajakhan1-1/+4
MCI interrupt is an asynchronous one, so take care of it by having a check in ath9k_hw_intrpend, which actually decides whether the interrupt is really for the driver from ath_isr Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: take care of enabling MCI interruptsMohammed Shafi Shajakhan1-4/+8
enable MCI interrupt when ath9k_hw_enable_interrupts is called, like during the completion of chip_reset before which the interrupts are disabled Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: Add MCI interrupt to interrupt maskMohammed Shafi Shajakhan1-1/+5
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: Add MCI h/w code and state machineMohammed Shafi Shajakhan3-1/+1492
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: initialize MCI parametersMohammed Shafi Shajakhan1-0/+22
these parameter will be utilized and modified in the MCI hardware codes state machine Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: Add MCI h/w specific structureMohammed Shafi Shajakhan1-0/+31
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: add GPIO output MUX related macrosMohammed Shafi Shajakhan1-0/+10
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k_hw: add definitions to support MCI h/w codeMohammed Shafi Shajakhan4-26/+529
these definitions will be used by MCI state machine and the corresponding hardware code Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: change the default antenna settings based on diversityMohammed Shafi Shajakhan1-9/+14
change the AR_DEF_ANTENNA register settings i.e setting default antenna setting only for antenna diversity enabled chipsets. no point in doing this for MIMO chipsets Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30ath9k: Fix LED GPIO pin for AR9462Mohammed Shafi Shajakhan1-1/+1
GPIO pin 4 is assigned AR9462 chipsets LED. while GPIO pin 0 worked for obselete AR9462 chipsets though they are meant for EEPROM as per Russell Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Russell Hu <rhu@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28ath9k_hw: cosmetic change in calibration debug logMohammed Shafi Shajakhan1-1/+1
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28ath9k_hw: Fix minimum CTL power for each runtime modeRajkumar Manoharan4-10/+8
The conformance test limits (CTL) for each regulatory domains (FCC/ETSI/MKK) are programmed for each runtime modes (11B,11G, HT20 and HT40) in EEPROM. The lowest ctledge power value of a particular running mode should not be used while computing ctledge power for a different running mode.(i.e 11G's min ctledge power should not be used while computing ctledge power for HT20). Currently, the code does not handle this properly which would result in incorrect txpowers in certain cases. So reset the twiceMaxEdgePower to the default while computing min ctlegepower for every mode. Cc: David Quan <dquan@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28ath9k: improve ath_tx_aggr_stop to avoid TID stuck in cleanup stateNikolay Martynov1-7/+6
When tx agg is being stopped TID is flushed using ath_tx_flush_tid. It is possible that ath_tx_flush_tid completelly flushes TID (if all packets in this TID have already been retried). If this happened ath_tx_aggr_stop would leave TID in cleanup state permanently. Fix this by making ath_tx_flush_tid remove AGGR_ADDBA_COMPLETE and AGGR_CLEANUP flags from TID status if TID is empty. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28ath9k: Revert change that broke AR928X on Acer Ferrari OneRafael J. Wysocki1-1/+2
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by commit 2577c6e8f2320f1d2f09be122efef5b9118efee4 (ath9k_hw: Add support for AR946/8x chipsets) that caused a nasty regression to appear on my Acer Ferrari One (the box locks up entirely at random times after the wireless has been started without any way to get debug information out of it). Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-27ath9k: Revert change that broke AR928X on Acer Ferrari OneRafael J. Wysocki1-1/+2
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by commit 2577c6e8f232 ("ath9k_hw: Add support for AR946/8x chipsets") that caused a nasty regression to appear on my Acer Ferrari One (the box locks up entirely at random times after the wireless has been started without any way to get debug information out of it). Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-11-22Merge branch 'master' of ↵John W. Linville15-0/+15
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux Conflicts: drivers/net/wireless/iwlegacy/iwl-debugfs.c drivers/net/wireless/iwlegacy/iwl-rx.c drivers/net/wireless/iwlegacy/iwl-scan.c drivers/net/wireless/iwlegacy/iwl-tx.c include/net/bluetooth/bluetooth.h
2011-11-21ath9k: trivial: reorder rx_tasklet processingZefir Kurtisi1-5/+5
DFS events are reported as PHY errors and need to be processed with a correct timestamp set before ath9k_skb_preprocess() is called and the frame is possibly dropped. This patch puts the rxs->mactime calculation before the skb is preprocessed to prepare for DFS event reporting. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-17ath9k_hw: set btcoex weights for AR9462Rajkumar Manoharan3-4/+37
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-17ath9k_hw: Cleanup btcoex wlan weightsRajkumar Manoharan4-58/+34
Remove all wlan weight macros and group it together for better understanding & readability. It makes the code reusable for AR9462 wlan weights. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-17ath9k: Remove enabling btcoex from stomp type changeRajkumar Manoharan3-4/+4
This patch removes btcoex_enable from stomp type change and let it be called from callee functions that makes the code can be reusable for MCI changes. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11ath9k_hw: Fix tx power settings for AR9003Rajkumar Manoharan1-0/+2
Retriving tx power for 2x2 and 3x3 chainmask is not handled properly. While calculating tx power for 2x2, 3 dBm was reduced and for 3x3, 5 dBm was reduced which should be added back when retriving. Cc: Paul Stewart <pstew@google.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11ath9k: set ATH9K_PCI to y by defaultDaniel Kuehn1-0/+1
Most ath9k devices are PCI/PCIe based, therefor making PCI/PCIe support default y helps those porting a config from 2.6 kernel series from getting "non-functional" wireless drivers with 3.x kernel series. Signed-off-by: Daniel Kuehn <daniel@kuehn.se> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11ath9k_hw: Fix channel list of CalFreqPeir for AR938xRajkumar Manoharan1-7/+7
This patch sync up CalFreqPeir channel list and paprd rate mask of AR938x templates to the latest received from Systems team. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11ath9k_hw: Read and configure xpa timing fieldRajkumar Manoharan1-0/+16
Configure xpa timing field while loading boad defaults to fix 11b CCK spur issue that was observed in EMI testing. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11ath9k_hw: Read and configure quick drop for AR9003Rajkumar Manoharan4-64/+59
Read and configure quick drop feild from AR9003 eeprom inorder to help with strong signal. This patch also removes obsolate parameters ob, db_stage2, db_stage_3, db_stage4 from the eeprom templates. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-09ath9k: Improve debugfs printout for stations.Ben Greear3-6/+14
Add interface address so it can be mapped to a local interface. Add max-ampdu and mpdu-density. Print out the tid->baw_size Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-09ath9k: Advertise support for TDLSJouni Malinen1-0/+1
Based on a quick test, TDLS seemed to be working fine with ath9k, so let's start advertising support for this in the driver. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-09Merge branch 'master' of ↵John W. Linville5-31/+31
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
2011-11-08ath9k_hw: Updated AR9462 initval table to improve rx performanceRajkumar Manoharan1-13/+13
The initval tables are updated as per system team input to improve rx performance and power accuracy at 5GHz. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-08ath9k: Add btcoex profile management support for AR9462Rajkumar Manoharan10-7/+402
AR9462 chips have the capabilities to provoide bluetooth profile information. For non-AR9462 btcoex chips, the BT priority traffic was identified by periodically polling the respective registers and updated dutycycle, stomptype, etc. As AR9462 chip offers the BT profile informations, let us make use of that to update aggregation limit, dutycycle, stomptype and wieghtages. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-08ath9k_hw: Update CCK spur mitigation for AR9462Rajkumar Manoharan1-1/+3
To improve CCK sensitivity for AR9462 chips, performing spur mitigation at 2440, 2464 frequencies alone is sufficient. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-08ath9k_hw: min_t() casts u32 to intDan Carpenter1-1/+1
The code here treats very large values of "limit" as less than MAX_POWER_RATE because of the cast to int. We should do the compare as u32 instead. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds5-31/+31
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits) forcedeth: fix a few sparse warnings (variable shadowing) forcedeth: Improve stats counters forcedeth: remove unneeded stats updates forcedeth: Acknowledge only interrupts that are being processed forcedeth: fix race when unloading module MAINTAINERS/rds: update maintainer wanrouter: Remove kernel_lock annotations usbnet: fix oops in usbnet_start_xmit ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined etherh: Add MAINTAINERS entry for etherh bonding: comparing a u8 with -1 is always false sky2: fix regression on Yukon Optima netlink: clarify attribute length check documentation netlink: validate NLA_MSECS length i825xx:xscale:8390:freescale: Fix Kconfig dependancies macvlan: receive multicast with local address tg3: Update version to 3.121 tg3: Eliminate timer race with reset_task tg3: Schedule at most one tg3_reset_task run tg3: Obtain PCI function number from device ...
2011-11-02ath9k_hw: Fix noise floor calibration timeout on fast channel changeRajkumar Manoharan3-7/+3
During the fast channel change noise floor values are being loaded twice at init_cal and after channel_change. The commit "ath9k_hw: Improve fast channel change for AR9003 chips" overlooked it that caused failure to load nf while doing bgscan. This patch performs noise floor calibration after the fast and full reset. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-02ath9k_hw: Update AR9485 initvals to fix system hang issueRajkumar Manoharan1-5/+5
This patch fixes system hang when resuming from S3 state and lower rate sens failure issue. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-02ath9k_hw: Fix regression of register offset of AR9330/AR9340Rajkumar Manoharan1-5/+5
The commit ce407afc10 introduced regression for AR9330/AR9340 register offsets. Some of the register offsets are common for AR9330/AR9340/AR9485 except AR9380. Fix that. Cc: stable@kernel.org [3.1.0+] Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-02ath9k_hw: Fix radio retention for AR9462Rajkumar Manoharan1-2/+6
IQ calibration during fast channel change sometimes failed with RTT. And also restoring invalid radio retention readings during init cal could cause failure to set the channel properly. This patch counts the valid rtt history readings and clears rtt mask. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 00:07:26 +0000