summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2012-01-24stmmac: added PCI identifiersAlessandro Rubini1-3/+3
STM has a device ID within its own VENDOR space, and it is being used in the STA2X11 I/O Hub. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-24stmmac: fix phy naming inconsistencyAlessandro Rubini1-1/+1
After commit "db8857b stmmac: use an unique MDIO bus name" my device stopped being probed because two different names were being used in different places. This fixes the inconsistency. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Florian Fainelli <florian@openwrt.org> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23tg3: fix ipv6 header length computationEric Dumazet1-7/+2
tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head doesnt include any payload data. if (skb_is_gso_v6(skb)) hdr_len = skb_headlen(skb) - ETH_HLEN; This is not true anymore after commit f07d960df3 (tcp: avoid frag allocation for small frames) We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb) Its also true for IPv4 Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23skge: add byte queue limit supportstephen hemminger1-13/+24
This also changes the cleanup logic slightly to aggregate completed notifications for multiple packets. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23mv643xx_eth: Add Rx Discard and Rx Overrun statisticsPaulius Zaleckas1-0/+14
These statistics helped me a lot while searching who is losing packets in my setup. I added these stats to MIB group since they are very similar, but just in other registers. I have tested this patch on 88F6281 SoC. Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: fix compilation error with SOE in fw_dumpYuval Mintz1-1/+1
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: handle CHIP_REVISION during init_oneAriel Elior1-4/+5
The macro `CHIP_IS_E1x' requires `bp' to be initialized. As `bp' is not yet initialized during this phase of `bnx2x_init_dev', it accessed uninitialized fields in the struct. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: allow user to change ring size in ISCSI SD modeDmitry Kravkov1-1/+1
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: fix Big-Endianess in ethtool -tDmitry Kravkov1-3/+2
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: fixed ethtool statistics for MF modesYuval Mintz1-65/+41
Previosuly, in MF modes `ethtool -S' lacked some of the statistics which appeared in non-MF modes. This has been fixed. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-23bnx2x: credit-leakage fixup on vlan_mac_del_allYuval Mintz2-1/+54
Upon insertion of elements into the execution queue, it is validated that there are enough credits to support additional vlan-macs, and the credits are consumed. However, when removing a pending command in `bnx2x_vland_mac_del_all' the consumed credits are not released, which might cause leakage and eventually the inability to add new vlan-macs in certain scenarios. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22be2net: create RSS rings even in multi-channel configsSathya Perla1-2/+1
Currently RSS rings are not created in a multi-channel config. RSS rings can be created on one (out of four) interfaces per port in a multi-channel config. Doing this insulates the driver from a FW bug wherin multi-channel config is wrongly reported even when not enabled. This also helps performance in a multi-channel config, as one interface per port gets RSS rings. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22skge: check for PCI dma mapping errorsstephen hemminger1-13/+58
Driver should check for mapping errors. Machines with limited DMA maps may return an error when a PCI map is requested (not an issue on standard x86). Also use upper/lower 32 bits macros for clarity. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22skge: don't assert carrier until link is upstephen hemminger1-0/+1
Skge device would assert carrier (link up) as soon as network device open was called, rather than waiting until PHY has detected link. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4_core: map async events to arbitrary slave eqsMarcel Apfelbaum4-16/+22
Slave async events were mapped to single eq. This patch fixes this issue, so the slaves can map the async events to any eq. Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4_core: Fix mtt profile issueMarcel Apfelbaum2-2/+2
Num mtts from profile is really the number of mtt segments. Thus, in make profile, to get the proper number of MTT entries, must multiply num_mtts by mtts per segment. Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4_core: removed function index from vf.Marcel Apfelbaum10-53/+8
The Virtual Functions should not be aware their function number. Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4_en: eth statistics modificationEugenia Emantayev4-16/+74
In native mode display all available staticstics. In SRIOV mode on VF display only SW counters statistics, in SRIOV mode on hypervisor display SW counters and errors (got from FW) statistics. Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4: VF is not allowed to perform dump statsEugenia Emantayev1-0/+2
In multifunction mode - DUMP_STATS command is not executed for VFs. Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-22mlx4_en: clear all eth statistics when port goes upEugenia Emantayev1-12/+24
Bug fix: Not all stats fields were cleared. Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petriln <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-20enic: fix compile when CONFIG_PCI_IOV is not enabledRoopa Prabhu1-2/+2
reverting back change that access enic->num_vfs outside CONFIG_PCI_IOV Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19ixgbevf: make operations tables constStephen Hemminger4-8/+8
The arrays of function pointers should be const to make life harder for rootkits. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19ixgbevf: fix sparse warningsStephen Hemminger3-2/+4
Fixes sparse warnings: drivers/net/ethernet/intel/ixgbevf/vf.c:418:21: warning: symbol 'ixgbevf_82599_vf_info' was not declared. Should it be static? drivers/net/ethernet/intel/ixgbevf/vf.c:423:21: warning: symbol 'ixgbevf_X540_vf_info' was not declared. Should it be static? drivers/net/ethernet/intel/ixgbevf/mbx.c:331:29: warning: symbol 'ixgbevf_mbx_ops' was not declared. Should it be static? Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19ixgbevf: make ethtool ops and strings constStephen Hemminger1-2/+3
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19ixgbevf: Prevent possible race condition by checking for messageGreg Rose1-18/+21
The mailbox interrupt routine might cause a race condition sometimes and cause a message to be missed. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19ixgbe: Fix register defines to correctly handle complex expressionsAlexander Duyck1-16/+16
This patch is meant to address possible issues with the IXGBE register defines generating incorrect values when given a complex expression for the register offset. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19igbvf: Remove unnecessary irq disable/enableMitch A Williams1-5/+0
This irq disable/enable pair used to wrap access to the driver's vlgrp struct, which is no longer present. So, then, this could also so no longer be present. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19igbvf: remove unneeded castStephen Hemminger1-2/+1
The cast and comment are unnecessary in the current upstream kernel. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Garrett, RobertX E <robertx.e.garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19igb: Update Copyright on all Intel copyrighted files.Carolyn Wyborny17-18/+18
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-19igb: make local functions staticStephen Hemminger2-4/+4
Sparse caught two functions that were only being used in one file. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18net: ftgmac100/ftmac100: add missing interrupt.h includeThomas Faber2-0/+2
Fixes compilation failure of these modules due to missing irqreturn_t type for the ft(g)mac100_interrupt definition. Signed-off-by: Thomas Faber <thfabba@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18pch_gbe: Do not abort probe on bad MACDarren Hart1-3/+14
If the MAC is invalid or not implemented, do not abort the probe. Issue a warning and prevent bringing the interface up until a MAC is set manually (via ifconfig $IFACE hw ether $MAC). Tested on two platforms, one with a valid MAC, the other without a MAC. The real MAC is used if present, the interface fails to come up until the MAC is set on the other. They successfully get an IP over DHCP and pass a simple ping and login over ssh test. This is meant to allow the Inforce SYS940X development board: http://www.inforcecomputing.com/SYS940X_ECX.html (and others suffering from a missing MAC) to work with the mainline kernel. Without this patch, the probe will fail and the interface will not be created, preventing the user from configuring the MAC manually. This does not make any attempt to address a missing or invalid MAC for the pch_phub driver. Signed-off-by: Darren Hart <dvhart@linux.intel.com> CC: Arjan van de Ven <arjan@linux.intel.com> CC: Alan Cox <alan@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: "David S. Miller" <davem@davemloft.net> CC: Paul Gortmaker <paul.gortmaker@windriver.com> CC: Jon Mason <jdmason@kudzu.us> CC: netdev@vger.kernel.org CC: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Laight <David.Laight@ACULAB.COM> CC: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18enic: fix location of vnic dev unregister in enic_probe cleanup codeRoopa Prabhu1-1/+1
The vnic_dev_unregister is erroneously under CONFIG_PCI_IOV. This patch moves it out of CONFIG_PCI_IOV Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Sujith Sankar <ssujith@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18enic: rearrange some of the port profile codeRoopa Prabhu1-7/+7
This patch rearranges some of the port profile code in enic_probe. It moves out some lines of port profile related code currently inside CONFIG_PCI_IOV. This is only done to move all port profile related code together so that it can help isolate the port profile handling code under a separate #ifdef in our internal build scripts. Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Sujith Sankar <ssujith@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18enic: Add sriov vf device id checks in port profile codeRoopa Prabhu1-9/+8
This patch adds checks for sriov vf's in enic port profile handling code. sriov vf's are same as dynamic vnics but with a different device id. Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Sujith Sankar <ssujith@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18enic: This patch adds pci id 0x71 for SRIOV VF'sRoopa Prabhu2-1/+8
This patch adds pci id 0x71 for sriov VF's. Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Sujith Sankar <ssujith@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18mlx4_en: set number of rx rings used by RSS using ethtoolYevgeny Petrilin4-7/+102
Value must be a power of 2 due to HW limitation. Driver supports only 'equal' mode in ethtool and can't be set by using weights. Signed-off-by: Amir Vadai <amirv@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds8-169/+214
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits) tg3: Fix single-vector MSI-X code openvswitch: Fix multipart datapath dumps. ipv6: fix per device IP snmp counters inetpeer: initialize ->redirect_genid in inet_getpeer() net: fix NULL-deref in WARN() in skb_gso_segment() net: WARN if skb_checksum_help() is called on skb requiring segmentation caif: Remove bad WARN_ON in caif_dev caif: Fix typo in Vendor/Product-ID for CAIF modems bnx2x: Disable AN KR work-around for BCM57810 bnx2x: Remove AutoGrEEEn for BCM84833 bnx2x: Remove 100Mb force speed for BCM84833 bnx2x: Fix PFC setting on BCM57840 bnx2x: Fix Super-Isolate mode for BCM84833 net: fix some sparse errors net: kill duplicate included header net: sh-eth: Fix build error by the value which is not defined net: Use device model to get driver name in skb_gso_segment() bridge: BH already disabled in br_fdb_cleanup() net: move sock_update_memcg outside of CONFIG_INET mwl8k: Fixing Sparse ENDIAN CHECK warning ...
2012-01-17tg3: Fix single-vector MSI-X codeMatt Carlson1-13/+14
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel) enabled. However, kdump only enables one CPU in the new environment, thus causing tg3 to abort MSI-X setup. When the driver attempts to enable INTA or MSI interrupt modes on a kdump kernel, interrupt delivery fails. This patch attempts to workaround the problem by forcing the driver to enable a single MSI-X interrupt. In such a configuration, the device's multivector interrupt mode must be disabled. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds1-2/+2
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits) ARM: mach-shmobile: specify CHCLR registers on SH7372 dma: shdma: fix runtime PM: clear channel buffers on reset dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit dmaengine/ste_dma40: clear LNK on channel startup dmaengine: intel_mid_dma: remove legacy pm interface ASoC: mxs: correct 'direction' of device_prep_dma_cyclic dmaengine: intel_mid_dma: error path fix dmaengine: intel_mid_dma: locking and freeing fixes mtd: gpmi-nand: move to dma_transfer_direction mtd: fix compile error for gpmi-nand mmc: mxs-mmc: fix the dma_transfer_direction migration dmaengine: add DMA_TRANS_NONE to dma_transfer_direction dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled. dma: mxs-dma: fix a typo in comment DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove video i.MX IPU: Fix display connections i.MX IPU DMA: Fix wrong burstsize settings dmaengine/ste_dma40: allow fixed physical channel ... Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c} The conflicts looked pretty trivial, but I'll ask people to verify them.
2012-01-17bnx2x: Disable AN KR work-around for BCM57810Yaniv Rosner1-1/+9
Disable the work-around for the autoneg KR of the BCM57810 in case the Warpcore version is 0xD108 and above, which fixes this problem. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17bnx2x: Remove AutoGrEEEn for BCM84833Yaniv Rosner1-6/+2
Disable the autoGrEEEn feature for BCM84833. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17bnx2x: Remove 100Mb force speed for BCM84833Yaniv Rosner2-6/+21
Remove unsupported speed of 100Mb force for BCM84833 due to hardware limitation. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17bnx2x: Fix PFC setting on BCM57840Yaniv Rosner2-10/+13
This patch handles the second port of a path in a 4-port device of BCM57840. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17bnx2x: Fix Super-Isolate mode for BCM84833Yaniv Rosner1-113/+137
The Super-Isolate mode comes to isolate the BCM84833 PHY from the outside world. Not doing it correctly, made link partner see the link before the driver was loaded. This patch also involves SPIROM version fixes since it is used to determine whether the common init of the PHY was already executed, and the common init of this PHY is partially responsible for setting the Super-Isolate mode. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17net: sh-eth: Fix build error by the value which is not definedNobuhiro Iwamatsu1-1/+1
----- drivers/net/ethernet/renesas/sh_eth.c:1706: error: 'pdid' undeclared (first use in this function) drivers/net/ethernet/renesas/sh_eth.c:1706: error: (Each undeclared identifier is reported only once drivers/net/ethernet/renesas/sh_eth.c:1706: error: for each function it appears in.) make[5]: *** [drivers/net/ethernet/renesas/sh_eth.o] Error 1 ----- Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-17ehea: make some functions and variables staticThadeu Lima de Souza Cascardo3-25/+23
Some functions and variables in ehea are only used in their own file, so they should be static. One particular function had a very generic name, print_error_data. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-12net: fsl: fec: handle 10Mbps speed in RMII modeEric Benard2-3/+10
when the link is 10 Mbps and the mode is RMII, it's necessary to set FRCONT to 1 in MIIGSK_CFGR to divide the RMII source clock by 10 in order to support 10 Mbps operations. Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-12drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c: add missing iounmapJulia Lawall1-1/+1
Add missing iounmap in error handling code, in a case where the function already preforms iounmap on some other execution path. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e; statement S,S1; int ret; @@ e = \(ioremap\|ioremap_nocache\)(...) ... when != iounmap(e) if (<+...e...+>) S ... when any when != iounmap(e) *if (...) { ... when != iounmap(e) return ...; } ... when any iounmap(e); // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-12drivers/net/ethernet/tundra/tsi108_eth.c: add missing iounmapJulia Lawall1-2/+4
Add missing iounmap in error handling code, in a case where the function already preforms iounmap on some other execution path. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e; statement S,S1; int ret; @@ e = \(ioremap\|ioremap_nocache\)(...) ... when != iounmap(e) if (<+...e...+>) S ... when any when != iounmap(e) *if (...) { ... when != iounmap(e) return ...; } ... when any iounmap(e); // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-13 16:49:45 +0000