| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
|
|
ppc has special instruction forms to efficiently load and store values
in non-native endianness. These can be accessed via the arch-specific
{ld,st}_le{16,32}() inlines in arch/powerpc/include/asm/swab.h.
However, gcc is perfectly capable of generating the byte-reversing
load/store instructions when using the normal, generic cpu_to_le*() and
le*_to_cpu() functions eaning the arch-specific functions don't have much
point.
Worse the "le" in the names of the arch specific functions is now
misleading, because they always generate byte-reversing forms, but some
ppc machines can now run a little-endian kernel.
To start getting rid of the arch-specific forms, this patch removes them
from all the old Power Macintosh drivers, replacing them with the
generic byteswappers.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add missing platform_set_drvdata() in mace_probe(), otherwise
calling platform_get_drvdata() in mac_mace_device_remove() may
returns NULL.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This restores commits:
c573972c111eb4c6b3f3250ad71e7c75cc799833
1a5904342c7380ceddd61c0b37544d752d0b1433
da2e2c214953f37c2a6be20226537ca5a329724c
which initially accidently went into 'net', were
reverted there, and then properly placed into 'net-next'.
But the next net --> net-next merge accidently wiped them
out again.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up the code a bit to initialize the variables directly when
defining them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refs:
1. pmac32_defconfig
http://kisskb.ellerman.id.au/kisskb/buildresult/5583746/
2. ppc6xx_defconfig
http://kisskb.ellerman.id.au/kisskb/buildresult/5584116/
Confirmed any such occurances from all failed defconfigs &
in net-next sources with
grep -nrs "netdev_alloc_skb" drivers/net/ethernet/ | grep -v ","
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.
This also fixes a build problem, as the driver needs a header file from the
cirrus directory:
drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cs89x0 driver was initial placed in the apple/ when it
should have been placed in the cirrus/. This resolves the
issue by moving the dirver and fixing up the respective
Kconfig(s) and Makefile(s).
Thanks to Sascha for reporting the issue.
-v2 Fix a config error that was introduced with v1 by removing
the dependency on MACE for NET_VENDOR_APPLE.
CC: Russell Nelson <nelson@crynwr.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We check ether_type before registering the platform device in
arch/m68k/mac/config.c. Doing the same test again in the driver is
redundant so remove it.
Multiple probes should not happen since the conversion to platform devices,
so lose that test too.
Then macmace.c need not include macintosh.h, so remove that and irq.h and
include linux/interrupt.h explicitly.
Tested on PowerBook 520, Quadra 660av, LC 630.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
replace it by ndo_set_rx_mode
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the Apple drivers into driver/net/ethernet/apple/ and make the
necessary Kconfig and Makefile changes.
CC: Paul Mackerras <paulus@samba.org>
CC: Paul Mackerras <paulus@au.ibm.com>
CC: Russell Nelson <nelson@crynwr.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
