summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)AuthorFilesLines
2009-06-14Merge branch 'for-linus' of ↵Linus Torvalds16-203/+1453
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits) atmel-mci: add MCI2 register definitions atmel-mci: Integrate AT91 specific definition in header file tmio_mmc: allow compilation for ASIC3 mmc_block: do not DMA to stack sdhci: Print ADMA status and pointer on debug tmio_mmc: fix clock setup tmio_mmc: map SD control registers after enabling the MFD cell tmio_mmc: correct probe return value for num_resources != 3 tmio_mmc: don't use set_irq_type tmio_mmc: add bus_shift support MFD,mmc: tmio_mmc: make HCLK configurable mmc_spi: don't use EINVAL for possible transmission errors cb710: more cleanup for the DEBUG case. sdhci: platform driver for SDHCI mxcmmc: remove frequency workaround cb710: handle DEBUG define in Makefile cb710: add missing parenthesis cb710: fix printk format string mmc: Driver for CB710/720 memory card reader (MMC part) pxamci: add regulator support. ...
2009-06-14Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds4-7/+8
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits) MAINTAINERS: EB110ATX is not ebsa110 MAINTAINERS: update Eric Miao's email address and status fb: add support of LCD display controller on pxa168/910 (base layer) [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines [ARM] 5544/1: Trust PrimeCell resource sizes [ARM] pxa/sharpsl_pm: cleanup of gpio-related code. [ARM] pxa/sharpsl_pm: drop set_irq_type calls [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific [ARM] sa1100: remove unused collie_pm.c [ARM] pxa: fix the conflicting non-static declarations of global_gpios[] [ARM] 5550/1: Add default configure file for w90p910 platform [ARM] 5549/1: Add clock api for w90p910 platform. [ARM] 5548/1: Add gpio api for w90p910 platform [ARM] 5551/1: Add multi-function pin api for w90p910 platform. [ARM] Make ARM_VIC_NR depend on ARM_VIC [ARM] 5546/1: ARM PL022 SSP/SPI driver v3 ARM: OMAP4: SMP: Update defconfig for OMAP4430 ARM: OMAP4: SMP: Enable SMP support for OMAP4430 ...
2009-06-13atmel-mci: add MCI2 register definitionsNicolas Ferre1-0/+22
New revision of Atmel MCI interface adds new features. This is a update of register definition in header file. This new MCI IP is called MCI2. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13atmel-mci: Integrate AT91 specific definition in header fileNicolas Ferre1-0/+11
The MCI IP is shared among AVR32 and AT91 SOCs. AT91 has specific bit definitions in the user interface of MCI SD/MMC IP. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: allow compilation for ASIC3Philipp Zabel2-3/+3
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <spyro@f2s.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_block: do not DMA to stackBen Dooks1-4/+12
In the write recovery routine, the data to get from the card is allocated from the stack. The DMA mapping documentation says explicitly stack memory is not mappable by any of the DMA calls. Change to using kmalloc() to allocate the memory for the result from the card and then free it once we've finished with the transaction. [ Changed to GFP_KERNEL allocation - Pierre Ossman ] Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13sdhci: Print ADMA status and pointer on debugBen Dooks1-0/+5
If using ADMA, then we should print the ADMA error and current pointer in sdhci_dumpregs() when any debug is requested. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: fix clock setupIan Molton1-10/+5
This patch fixes the clock setup in tmio_mmc. * Incorrect divider setting * Cruft written to the clock registers (seemingly harmless but Not Good (tm)) It also eliminates some unnecessary ifs and tidies the loop syntax. Thanks to Philipp Zabel who discovered the divider issue, commenting "Except for the SDCLK = HCLK (divider bypassed) case, the clock setting resulted in double the requested frequency. The smallest possible frequency (f_max/512) is configured with a divider setting 0x80, not 0x40." Signed-off-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: map SD control registers after enabling the MFD cellPhilipp Zabel1-10/+10
ASIC3 can disable the memory, so we need to wait for mfd_cell->enable to enable the memory before we can map the SD control registers. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: correct probe return value for num_resources != 3Philipp Zabel1-7/+5
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: don't use set_irq_typePhilipp Zabel1-4/+2
Use an IRQF_TRIGGER_ flag in request_irq instead. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13tmio_mmc: add bus_shift supportPhilipp Zabel2-81/+125
Some ASIC3 devices in the wild are connected with the address bus shifted by one line, so that its 16-bit registers appear 32-bit aligned in host memory space. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13MFD,mmc: tmio_mmc: make HCLK configurablePhilipp Zabel1-13/+11
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Acked-by: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_spi: don't use EINVAL for possible transmission errorsWolfgang Muees1-5/+6
This patch changes the reported error code for the responses to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved for non-recoverable host errors, and the responses from the SD/MMC card may be because of recoverable transmission errors in the command or in the response. Response codes in SPI mode are NOT protected by a checksum, so don't trust them. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Acked-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: more cleanup for the DEBUG case.Michał Mirosław1-0/+3
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13sdhci: platform driver for SDHCIRichard Röjfors3-0/+180
Added a platform driver which uses the SDHCI core. Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mxcmmc: remove frequency workaroundPierre Ossman1-2/+0
The MMC core has now been fixed to not send silly frequencies to the drivers which means we can remove this workaround. Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13cb710: fix printk format stringPierre Ossman1-1/+1
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc: Driver for CB710/720 memory card reader (MMC part)Michał Mirosław4-0/+922
The code is divided in two parts. There is a virtual 'bus' driver that handles PCI device and registers three new devices one per card reader type. The other driver handles SD/MMC part of the reader. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13pxamci: add regulator support.Daniel Ribeiro1-5/+41
Changes pxamci.c to use the regulator subsystem. Uses the regulator case CONFIG_REGULATOR is defined and a matching is regulator is provided, or falls back to pdata->setpower otherwise. A warning is displayed case both a valid regulator and pdata is set, and the regulator is used. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13MMC core: limit minimum initialization frequency to 400kHzSascha Hauer1-1/+7
Some controllers allow a much lower frequency than 400kHz. Keep the minimum frequency within sensible limits. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-13sdhci: avoid changing voltage needlesslyPierre Ossman2-26/+29
Because of granularity issues, sometimes we told the hardware to change to the voltage we were already at. Rework the logic so this doesn't happen. Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc/omap: make mmci-omap using platform_driver_probeUwe Kleine-König1-2/+1
A pointer to mmc_omap_probe which lives in .init.text is passed to the core via platform_driver_register and so the kernel might oops if probe is called after the init code is discarded. As requested by David Brownell platform_driver_probe is used instead of moving the probe function to .devinit.text. This saves some memory, but might have the downside that a device being registered after the call to mmc_omap_init but before the init sections are discarded will not be bound anymore to the driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc_spi: speedup for slow cards, less wear-outWolfgang Muees1-0/+12
Speedup for slow cards by transfering more data at once. This patch also reduces the amount of wear-out of the flash blocks because fewer partial blocks are written. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13mmc: mmc_rescan detects card change in one runJorg Schummer1-44/+55
With this patch, mmc_rescan can detect the removal of an mmc card and the insertion of (possibly another) card in the same run. This means that a card change can be detected without having to call mmc_detect_change multiple times. This change generalises the core such that it can be easily used by hosts which provide a mechanism to detect only the presence of a card reader cover, which has to be taken off in order to insert a card. Other hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when a card is removed and when a card is inserted, so it is sufficient for them if mmc_rescan handles only one event at a time. "Cover detect" hosts, however, only receive events about the cover status. This means that between 2 subsequent events, both a card removal and a card insertion can occur. In this case, the pre-patch version of mmc_rescan would only detect the removal of the previous card but not the insertion of the new card. Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6Linus Torvalds1-3/+9
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: avr32: Fix oops on unaligned user access avr32: Add support for Mediama RMTx add-on board for ATNGW100 avr32: Change Atmel ATNGW100 config to add choice of add-on board Fix MIMC200 board LCD init avr32: Fix clash in ATMEL_USART_ flags avr32: remove obsolete hw_interrupt_type avr32: Solves problem with inverted MCI detect pin on Merisc board atmel-mci: Add support for inverted detect pin
2009-06-13Merge branch 'avr32-arch' of ↵Haavard Skinnemoen1-3/+9
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
2009-06-11Merge branch 'for-2.6.31' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds2-14/+9
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits) block: add request clone interface (v2) floppy: fix hibernation ramdisk: remove long-deprecated "ramdisk=" boot-time parameter fs/bio.c: add missing __user annotation block: prevent possible io_context->refcount overflow Add serial number support for virtio_blk, V4a block: Add missing bounce_pfn stacking and fix comments Revert "block: Fix bounce limit setting in DM" cciss: decode unit attention in SCSI error handling code cciss: Remove no longer needed sendcmd reject processing code cciss: change SCSI error handling routines to work with interrupts enabled. cciss: separate error processing and command retrying code in sendcmd_withirq_core() cciss: factor out fix target status processing code from sendcmd functions cciss: simplify interface of sendcmd() and sendcmd_withirq() cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code cciss: Use schedule_timeout_uninterruptible in SCSI error handling code block: needs to set the residual length of a bidi request Revert "block: implement blkdev_readpages" block: Fix bounce limit setting in DM Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt ... Manually fix conflicts with tracing updates in: block/blk-sysfs.c drivers/ide/ide-atapi.c drivers/ide/ide-cd.c drivers/ide/ide-floppy.c drivers/ide/ide-tape.c include/trace/events/block.h kernel/trace/blktrace.c
2009-06-11[ARM] 5544/1: Trust PrimeCell resource sizesLinus Walleij1-1/+1
I found the PrimeCell/AMBA Bus drivers distrusting the resource passed in as part of the struct amba_device abstraction. This patch removes all hard coded resource sizes found in the PrimeCell drivers and move the responsibility of this definition back to the platform/board device definition, which already exist and appear to be correct for all in-tree users of these drivers. We do this using the resource_size() inline function which was also replicated in the only driver using the resource size, so that has been changed too. The KMI_SIZE was left in kmi.h in case someone likes it. Test-compiled against Versatile and Integrator defconfigs, seems to work but I don't posess these boards and cannot test them. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-10Merge branch for-rmk-devel of git://aeryn.fluff.org.uk/bjdooks/linux into develRussell King1-2/+3
2009-06-03sdhci-of: Fix the wrong accessor to HOSTVER registerDave Liu1-1/+7
Freescale eSDHC controller has the special order for the HOST version register. that is not same as the other's registers. The address of HOSTVER in spec is 0xFE, and we need use the in_be16(0xFE) to access it, not in_be16(0xFC). Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mvsdio: fix config failure with some high speed SDHC cardsNicolas Pitre1-0/+25
Especially with Sandisk SDHC cards, the second SWITCH command was failing with a timeout and the card was not recognized at all. However if the system was busy, or debugging was enabled, or a udelay(100) was inserted before the second SWITCH command in the core code, then the timing was so that the card started to work. With some unusual block sizes, the data FIFO status doesn't indicate a "empty" state right away when the data transfer is done. Queuing another data transfer in that condition results in a transfer timeout. The empty FIFO bit eventually get set by itself in less than 50 usecs when it is not set right away. So let's just poll for that bit before configuring the controller with a new data transfer. Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mvsdio: ignore high speed timing requests from the coreNicolas Pitre1-0/+9
Empirical evidences show that this is causing far more problems than it solves when this mode is enabled in the host hardware. Amongst those cards that are known to be non functional when this bit is set are: A-Data "Speedy" 2GB SD card Kodak 512MB SD card Ativa 1GB MicroSD card Marvell 8688 (WIFI/Bluetooth) SDIO card Since those cards do work on other host controllers which do honnor the hs timing, the issue must be with this particular host hardware. Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mmc/omap: Use disable_irq_nosync() from within irq handlers.Ben Nizette1-1/+1
disable_irq() should wait for all running handlers to complete before returning. As such, if it's used to disable an interrupt from that interrupt's handler it will deadlock. This replaces the dangerous instances with the _nosync() variant which doesn't have this problem. Signed-off-by: Ben Nizette <bn@niasdigital.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03sdhci-of: Add fsl,esdhc as a valid compatible to bind againstKumar Gala1-0/+1
We plan to use fsl,esdhc going forward as the base compatible so update the driver to bind against it. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mvsdio: allow automatic loading when modularNicolas Pitre1-0/+1
Signed-off-by: Nicolas Pitre <nico@marvell.com> Tested-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mxcmmc: Fix missing return value checking in DMA setup code.Martin Fuzzey1-10/+26
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
2009-06-03mxcmmc : Reset the SDHC hardware if software timeout occurs.Martin Fuzzey1-1/+6
When a software timeout occurs in polling mode hardware was left in an indeterminate state causing subsequent operations to block. Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
2009-06-03omap_hsmmc: Trivial fix for a typo in commentAnand Gadiyar1-1/+1
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-03mxcmmc: decrease minimum frequency to make MMC cards workSascha Hauer1-1/+3
This is a temporary workaround until the MMC stack can be fixed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-05-29Merge branch 'for-next' of ↵Russell King1-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel Conflicts: arch/arm/Makefile
2009-05-29Merge branch 'for-next' of ↵Russell King1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into devel
2009-05-28ARM: OMAP3: mmc-twl4030 uses regulator frameworkDavid Brownell1-3/+3
Decouple the HSMMC glue from the twl4030 as the only regulator provider, using the regulator framework instead. This makes the glue's "mmc-twl4030" name become a complete misnomer ... this code could probably all migrate into the HSMMC driver now. Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD), plus some other boards (including Overo) after they were converted to set up MMC regulators properly. Eventually all boards should just associate a regulator with each MMC controller they use. In some cases (Overo MMC2 and Pandora MMC3, at least) that would be a fixed-voltage regulator with no real software control. As a temporary hack (pending regulator-next updates to make the "fixed.c" regulator become usable) there's a new ocr_mask field for those boards. Patch updated with a fix for disabling vcc_aux by Adrian Hunter <adrian.hunter@nokia.com> Cc: Pierre Ossman <drzeus-list@drzeus.cx> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-05-23Merge branch 'ixp4xx' of ↵Russell King6-13/+22
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6 into devel
2009-05-22block: Do away with the notion of hardsect_sizeMartin K. Petersen1-1/+1
Until now we have had a 1:1 mapping between storage device physical block size and the logical block sized used when addressing the device. With SATA 4KB drives coming out that will no longer be the case. The sector size will be 4KB but the logical block size will remain 512-bytes. Hence we need to distinguish between the physical block size and the logical ditto. This patch renames hardsect_size to logical_block_size. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22Merge branch 'master' into for-2.6.31Jens Axboe1-1/+1
Conflicts: drivers/ide/ide-io.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22Merge branch 'master' into for-2.6.31Jens Axboe7-15/+22
Conflicts: drivers/block/hd.c drivers/block/mg_disk.c Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-21[ARM] S3C24XX: Merge devel-gpioBen Dooks1-1/+2
Merge branch 'devel-gpio' into for-rmk-devel
2009-05-20[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *Alessandro Rubini1-1/+1
The second argument of the probe method points to the amba_id structure, so it's better passed with the correct type. None of the current in-tree drivers uses the pointer, so they have only been checked for a clean compile. Change suggested by Russell King. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-18[ARM] S3C24XX: GPIO: Move gpio functions out of <mach/hardware.h>Ben Dooks1-1/+2
Move all the gpio functions out of <mach/hardware.h> as this file is for defining the generic IO base addresses for the kernel IO calls. Make a new header <mach/gpio-fns.h> to take this and include it via the chain from <linux/gpio.h> which is what most of these files should be using (and will be changed as soon as possible). Note, this does make minor changes to some drivers but should not mess up any pending merges. CC: Richard Purdie <rpurdie@rpsys.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-30 04:43:39 +0000