summaryrefslogtreecommitdiff
path: root/drivers/media/common/tuners
AgeCommit message (Collapse)AuthorFilesLines
2012-05-20[media] fc0013 ver. 0.2: introduction of get_rf_strength functionHans-Frieder Vogt1-1/+73
Changes compared to version 0.1 of driver (sent 6 May): - Initial implementation of get_rf_strength function. - Introduction of a warning message Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-20[media] fc0012 ver. 0.6: introduction of get_rf_strength functionHans-Frieder Vogt1-1/+71
Changes compared to version 0.5 of driver (sent 6 May): - Initial implementation of get_rf_strength function. Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-20[media] fc001x: tuner driver for FC0013Hans-Frieder Vogt5-0/+671
Support for tuner Fitipower FC0013 Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-20[media] fc001x: tuner driver for FC0012, version 0.5Hans-Frieder Vogt5-0/+492
Support for tuner Fitipower FC0012 Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-20[media] fc001x: common header file for FC0012 and FC0013Hans-Frieder Vogt1-0/+39
Common defines for the FC0012 (v0.5) and FC0013 tuner drivers Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19[media] xc5000: xtal_khz should be a u16 rather than a u32Michael Krufky2-2/+2
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19[media] xc5000: log firmware upload failures in xc5000_fwuploadMichael Krufky1-1/+4
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-19[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmwareMichael Krufky2-4/+36
Rather than loading firmware specific for the xtal frequency, just use the standard firmware and set the xtal frequency after firmware upload. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-09[media] fc0011: Reduce number of retriesMichael Büsch1-1/+1
Now that i2c transfers are fixed, 3 retries are enough. Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-09[media] fc0011: use usleep_range()Michael Büsch1-2/+2
Use usleep_range() instead of msleep() to improve power saving opportunities. Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-09[media] Add fc0011 tuner driverMichael Büsch4-0/+573
This adds support for the Fitipower fc0011 DVB-t tuner. Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-04-09[media] Infineon TUA 9001 silicon tuner driverAntti Palosaari5-0/+302
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-03-08[media] media: tuners: append $(srctree) to -I parametersAndy Shevchenko1-2/+2
Without this we have got the warnings like following if build with "make W=1 O=/var/tmp": cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default] Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-28[media] mt2063: remove mt2063_setTune from headerDanny Kukawka1-4/+0
Commit 99ac54125490f16f7434f82fcb73bbb88290b38e removed the function mt2063_setTune() from mt2063.c. Remove it also from the header file. Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] xc5000: declare firmware configuration structures as static constMichael Krufky1-4/+5
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] xc5000: drivers should specify chip revision rather than firmwareMichael Krufky2-19/+17
Specify chip revision at attach time rather than a firmware image. This is a better way to ensure that the correct firmware is loaded for the correct revision of the chip. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] xc5000: remove static dependencies on xc5000 created by previous ↵Michael Krufky2-13/+26
changesets convert the firmware configuration attach-time parameter from a pointer to an integer so as to remove the static dependency created by the previous changesets. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] remove unneeded #define's in xc5000.hMichael Krufky1-5/+2
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] tuner: add support for Xceive XC5000CMichael Krufky1-0/+4
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] xc5000: add XC5000C_DEFAULT_FIRMWARE: dvb-fe-xc5000c-41.024.5-31875.fwMichael Krufky2-1/+9
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-14[media] xc5000: allow drivers to set desired firmware in xc5000_attachMichael Krufky2-6/+29
newer versions of the xc5000 silicon require newer firmware while remaining 100% driver compatible. original versions of the xc5000a continue to use the same firmware. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-13[media] max2165: trival fix for some -Wuninitialized warningDanny Kukawka1-3/+6
Fix for some -Wuninitialized compiler warnings. Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-02-08[media] mt2063: increase frequency_max to tune channel 69Jose Alberto Reguero1-1/+1
Increase mt2063 frequency_max to tune to channel 69(858Mhz). Jose Alberto Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-21[media] az6007: Fix compilation troubles at az6007Mauro Carvalho Chehab1-1/+1
Some changes are needed, in order to make az6007 compile with the upstream tree. Most of the changes are due to the upstream drxk module. Even allowing its compilation, the driver is not working yet. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-16[media] Add registers names to XC2028 tuner from datahseet and use themMiroslav Slugen1-6/+21
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-16[media] xc4000: add support for signal strength measuresMiroslav Slugen1-0/+86
In xc4000 chipsets real signal and noise level is stored in register 0x0A and 0x0B,so we can use those registers to monitor signal strength. I tested this patch on 2 different cards Leadtek DVR3200 and DTV2000H Plus, both with same results, I used special antenna hubs (toner 4x, 6x, 8x and 12x) with mesured signal lost, both registers are in dB value, first represent signal with limit value -113.5dB (should be -114dB) and exactly match with test results. Second represents noise level also in dB and there is no maximum value, but from tests we can drop everything above 32dB which tuner realy can't use, signal was usable till 20dB noise level. In digital mode we can take signal strength but sadly noise level is not relevant and real value is stored in demodulator for now just zl10353, also digital mode is just for testing, because it needs changing other parts of code which reads data only from demodulator. In analog mode I was able to test only FM radio, signal level is not important, it says something about cable and hub losts, but nothing about real quality of reception, so even if we have signal level at minimum 113dB we can still here radio, because of that it is displaied only in debug mode, but for real signal level is used noise register which is again very accurate, radio noise level was betwen 6-20dB for good signal, 20-25dB for medium signal, and above 25dB signal is unusable. For now real benefit of this patch is only for FM radio mode. Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-10[media] mxl5007t: bugfix DVB-T 7 MHz and 8 MHz bandwidthAntti Palosaari1-0/+2
DVB-T did not work at all - only 6 MHz was working but it is not commonly used. Fix it. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-10[media] tda18271-fe: Fix support for ISDB-TMauro Carvalho Chehab1-0/+1
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-06[media] xc3028: fix center frequency calculation for DTV78 firmwareGianluca Gennari1-10/+16
This patch replaces the previous one proposed in the thread "xc3028: force reload of DTV7 firmware in VHF band with Zarlink demodulator", at the linux-media@vger.kernel.org ML. The problem is that the firmware DTV78 works fine in UHF band (8 MHz bandwidth) but is not working at all in VHF band (7 MHz bandwidth). Reading the comments inside the code, I figured out that the real problem could be connected to the formula used to calculate the center frequency offset in VHF band. In fact, removing this adjustment fixes the problem: if ((priv->cur_fw.type & DTV78) && freq < 470000000) offset -= 500000; This is coherent to what was implemented for the DTV7 firmware by an Australian user: if (priv->cur_fw.type & DTV7) offset += 500000; In the end, now the center frequency is the same for all firmwares (DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth. The final code looks clean and simple, and there is no need for any "magic" adjustment: if (priv->cur_fw.type & DTV6) offset = 1750000; else /* DTV7 or DTV8 or DTV78 */ offset = 2750000; Signed-off-by: Gianluca Gennari <gennarone@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-06[media] drivers: media: tuners: Fix dependency for MEDIA_TUNER_TEA5761Fabio Estevam1-1/+1
Fix the following build warning: warning: (MEDIA_TUNER) selects MEDIA_TUNER_TEA5761 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_MEDIA && I2C && EXPERIMENTAL) Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-05[media] mt2063: fix get_if_frequency callStefan Ringel1-1/+1
[mchehab@redhat.com: patch rebased to apply] Signed-off-by: Stefan Ringel <linuxtv@stefanringel.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] Don't test for ops->info.type inside driversMauro Carvalho Chehab1-1/+6
Now, ops->info.type is handled inside the dvb_frontend core, only for DVBv3 calls, and according with the delivery system. So, drivers should not care or use it, otherwise, it may have issues with DVBv5 calls. The drivers that were still using it were detected via this small temporary hack: --- a/include/linux/dvb/frontend.h +++ b/include/linux/dvb/frontend.h @@ -29,13 +29,16 @@ #include <linux/types.h> typedef enum fe_type { +#if defined(__DVB_CORE__) || !defined (__KERNEL__) FE_QPSK, FE_QAM, FE_OFDM, FE_ATSC +#else +FE_FOOO +#endif } fe_type_t; - typedef enum fe_caps { FE_IS_STUPID = 0, FE_CAN_INVERSION_AUTO = 0x1, Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Add it to the building systemMauro Carvalho Chehab2-0/+8
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Add support for get_if_frequency()Mauro Carvalho Chehab1-4/+4
get_if_frequency() is needed, in order to work with DRX-K. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: add some useful info for the dvb callback callsMauro Carvalho Chehab1-21/+47
The per-delivery system tables are confusing. Add an extra table that explains them, and some dprintk calls, that allows to check if mt2063 driver is working as expected. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: print the detected versionMauro Carvalho Chehab1-2/+1
Instead of printing it just for debug purposes, outputs the detected version at the logs. This may be useful if someone wants to report a problem. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Fix i2c read messageMauro Carvalho Chehab1-8/+16
While here, improve a few debug messages that helped to track the issue and may be useful in the future. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Print a message about the detected mt2063 typeMauro Carvalho Chehab1-4/+22
This also helps to identify when a device is not initialized, if the bridge doesn't return an error for a I2C failed transfer. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: don't crash if device is not initializedMauro Carvalho Chehab1-0/+25
Instead of crash, return -ENODEV, if the device is not poperly initialized. Also, give a second chance for it to initialize, at set_params calls. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Remove two unused temporary varsMauro Carvalho Chehab1-4/+1
mt2063.c:1531:12: warning: variable 'ofout' set but not used [-Wunused-but-set-variable] mt2063.c:1531:6: warning: variable 'ofin' set but not used [-Wunused-but-set-variable] Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Rewrite tuning logicMauro Carvalho Chehab1-49/+13
Several vars at set_parms functions were set, but unused. Remove them and change the logic to return -EINVAL if the analog set_param is used for digital mode. At the analog side, cleans the logic that sets the several analog standards. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Add some debug printk'sMauro Carvalho Chehab1-8/+68
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Convert it to the DVBv5 way for set_params()Mauro Carvalho Chehab1-29/+17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Properly document the author of the original driverMauro Carvalho Chehab1-2/+4
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Rearrange the delivery system functionsMauro Carvalho Chehab1-77/+66
No functional changes on this patch. Better organize the delivery system information and data types, putting everything together, to improve readability. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Fix commentsMauro Carvalho Chehab1-589/+370
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Fix analog/digital set params logicMauro Carvalho Chehab2-201/+190
The driver were using a hacky way of setting analog and digital frequencies. Remove the hack and properly add the tuner logic for each supported type of standard. I was tempted to add more standards there, like SECAM and to fix radio (as stepping seems broken), but I opted to keep it as-is, as tests would be needed to add additional standards. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: make checkpatch.pl happyMauro Carvalho Chehab1-81/+48
Fix everything but 80 columns and two msleep warnings Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Cleanup some function prototypesMauro Carvalho Chehab1-28/+16
No functional changes here. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04[media] mt2063: Reorder the code to avoid function prototypesMauro Carvalho Chehab1-181/+150
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-24 11:10:57 +0000