| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The dev_rdesc member of the hid_device structure is meant to store the original
report descriptor received from the device, but it is currently passed to any
report_fixup method before it is copied to the rdesc member. This patch uses a
temporary buffer to shield dev_rdesc from the side effects of many HID drivers'
report_fixup implementations.
usbhid's hid_post_reset checks the report descriptor currently returned by the
device against a descriptor that may have been modified by a driver's
report_fixup method. That leaves some devices nonfunctional after a resume, with
a "reset_resume error 1" reported. This patch checks the new descriptor against
the unmodified dev_rdesc instead and uses the original, instead of modified,
report size.
BugLink: http://bugs.launchpad.net/bugs/1049623
Signed-off-by: Kevin Daughtridge <kevin@kdau.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1597) fixes some of the error paths in usbhid's suspend
routine. The driver was not careful to restart everything that might
have been stopped, in cases where a suspend failed.
For example, once the HID_SUSPENDED flag is set, an output report
submission would not restart the corresponding URB queue. If a
suspend fails, it's therefore necessary to check whether the queues
need to be restarted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1596) improves the queue-restart logic in usbhid by
checking to see if the device is suspended or a reset is about to
occur. There's no point submitting an URB if either of those is
true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1595) improves the usbhid driver by using the
HID_SUSPENDED bitflag to indicate that the device is suspended rather
than using HID_REPORTED_IDLE, which the patch removes.
Since HID_SUSPENDED was not being used for anything, and since the
name "HID_REPORTED_IDLE" doesn't convey much meaning, the end result
is easier to read and understand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1594) simplifies the usbhid driver by inlining a couple
of routines. As a result of an earlier patch, irq_out_pump_restart()
and ctrl_pump_restart() are each used in only one place. Since they
don't really do what their names say, and since they each involve only
about two lines of actual code, there's no reason to keep them as
separate functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1593) fixes some logic errors in the usbhid driver
relating to runtime PM. The driver does not balance its calls to
usb_autopm_get_interface_async() and usb_autopm_put_interface_async().
For example, when the control queue is restarted the driver does a
_get. But the resume won't happen immediately, so the driver leaves
the queue stopped. When the resume does occur, the queue is restarted
and a second _get occurs, with no balancing _put.
The patch fixes the problem by rearranging the logic for restarting
the queues. All the _get/_put calls and bitflag settings in
__usbhid_submit_report() are moved into the queue-restart routines. A
balancing _put call is added for the case where the queue is still
suspended. A call to irq_out_pump_restart(), which doesn't take all
the right actions for restarting the irq-OUT queue, is replaced by a
call to usbhid_restart_out_queue(), which does. Similarly for
ctrl_pump_restart().
Finally, new code is added to prevent an autosuspend from happening
every time an URB is cancelled, and the comments explaining what
happens when an URB needs to be cancelled are expanded and clarified.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1592) fixes an obscure problem in the usbhid driver.
Under some circumstances, a control or interrupt-OUT URB can be
submitted twice. This will happen if the first submission fails; the
queue pointers aren't updated, so the next time the queue is restarted
the same URB will be submitted again.
The problem is that raw_report gets deallocated during the first
submission. The second submission will then dereference and try to
free an already-freed region of memory. The patch fixes the problem
by setting raw_report to NULL when it is deallocated and checking for
NULL before dereferencing it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID subsystem updates from Jiri Kosina:
"Apart from various driver updates and added support for a number of
new devices (mostly multitouch ones, but not limited to), there is one
change that is worth pointing out explicitly: creation of HID device
groups and proper autoloading of hid-multitouch, implemented by Henrik
Rydberg."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (50 commits)
HID: wacom: fix build breakage without CONFIG_LEDS_CLASS
HID: waltop: Extend barrel button fix
HID: hyperv: Set the hid drvdata correctly
HID: wacom: Unify speed setting
HID: wacom: Add speed setting for Intuos4 WL
HID: wacom: Move Graphire raport header check.
HID: uclogic: Add support for UC-Logic TWHL850
HID: explain the signed/unsigned handling in hid_add_field()
HID: handle logical min/max signedness properly in parser
HID: logitech: read all 32 bits of report type bitfield
HID: wacom: Add LED selector control for Wacom Intuos4 WL
HID: hid-multitouch: fix wrong protocol detection
HID: wiimote: Fix IR data parser
HID: wacom: Add tilt reporting for Intuos4 WL
HID: multitouch: MT interface matching for Baanto
HID: hid-multitouch: Only match MT interfaces
HID: Create a common generic driver
HID: hid-multitouch: Switch to device groups
HID: Create a generic device group
HID: Allow bus wildcard matching
...
|
|
Conflicts:
drivers/hid/hid-core.c
|
|
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the hid drivers of the bus drivers to a common generic hid
driver, and make it a proper module. This ought to simplify device
handling moving forward.
Cc: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Devices that do not have a special driver are handled by the generic
driver. This patch does the same thing using device groups; Instead of
forcing a particular driver, the appropriate driver is picked up by
udev. As a consequence, one can now move a device from generic to
specific handling by a simple rebind. By adding a new device id to the
generic driver, the same thing can be done in reverse.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When a USB device reset occurs, usbcore will refetch the device and configuration
descriptors and compare them with those retrieved before the reset to ensure
that they have not changed. For USB HID devices, this implicitly includes the
HID class descriptor (as this is fetched with the configuration descriptor).
However, the HID report descriptor is not checked again.
Whilst a change in the size of the HID report descriptor will be detected (as
this is held in the class descriptor), content changes to the report descriptor
which do not result in a change in its size will be missed. If a firmware update
were applied to a USB HID device which resulted in such a change to the report
descriptor after device reset, then this would not be picked up by usbhid.
This patch fixes this issue by allowing usbhid to check the contents of the
report descriptor after the device reset, and trigger a rebind of the device
if there is a mismatch.
Reviewed-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Simon Haggett <simon.haggett@realvnc.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In case IO cannot be started because there is a lack of bandwidth
on the bus, it makes no sense to reset the device. If IO is requested
because the device is opened, user space should be notified with
an error right away. If the lack of bandwidth arises later, for
example after resume, there's no other choice but to retry in the
hope that bandwidth will be freed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Defer LED setting action to a workqueue.
This is more likely to send all LED change events in a single URB.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If any userspace program has opened a keyboard device, the input core
de-activates the keyboard's LEDs upon suspend(). It does this by sending
individual EV_LED[LED_X]=0 events to the underlying device driver by
directly calling the driver's registered event() handler.
The usb-hid driver event() handler processes each request by immediately
attempting to submit a CTRL URB to turn off the LED. USB URB submission
is asynchronous. First the URB is added to the head of the ctrl queue.
Then, if the CTRL_RUNNING flag is false, the URB is submitted immediately
(and CTRL_RUNNING is set). If the CTRL_RUNNING flag was already true,
then the newly queued URB is submitted in the ctrl completion handler when
all previously submitted URBs have completed. When all queued URBs have
been submitted, the completion handler clears the CTRL_RUNNING flag.
In the 2-LED suspend case, at input suspend(), 2 LED event CTRL URBs get
queued, with only the first actually submitted. Soon after input
suspend() handler finishes, the usb-hid suspend() handler gets called.
Since this is NOT a PM_EVENT_AUTO suspend, the handler sets
REPORTED_IDLE, then waits for io to complete.
Unfortunately, this usually happens while the first LED request is
actually still being processed. Thus when the completion handler tries
to submit the second LED request it fails, since REPORTED_IDLE is
already set! This REPORTED_IDLE check failure causes the completion
handler to complete, however without clearing the CTRL_RUNNING flag.
This, in turn, means that the suspend() handler's wait_io() condition
is never satisfied, and instead it times out after 10 seconds, aborting
the original system suspend.
This patch changes the behavior to the following:
(1) allow completion handler to finish submitting all queued URBs, even if
REPORTED_IDLE is set. This guarantees that all URBs queued before the
hid-core suspend() call will be submitted before the system is
suspended.
(2) if REPORTED_IDLE is set and the URB queue is empty, queue, but
don't submit, new URB submission requests. These queued requests get
submitted when resume() flushes the URB queue. This is similar to the
existing behavior, however, any requests that arrive while the queue is
not yet empty will still get submitted before suspend.
(3) set the RUNNING flag when flushing the URB queue in resume().
This keeps URBs that were queued in (2) from colliding with any new
URBs that are being submitted during the resume process. The new URB
submission requests upon resume get properly queued behind the ones
being flushed instead of the current situation where they collide,
causing memory corruption and oopses.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
LED_ON was defined in the original version of the hid-core autosuspend patch.
However, during review, the setting and clearing of it was redone
using ledcount. The test was left in accidentally.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
|
|
This makes sure IO is never restarted while a reset is going on
In particular there seems to be no protection from hid_retry_timeout() calling
hid_start_in() which would start IO after hid_pre_reset() has already called
hid_cease_io() because that uses del_timer(), not del_timer_sync()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Unfortunately, the device seems to have the same Vendor ID and Product ID
as YUREX leg-shakes sensors, and the commit 6bc235a2e2 ("USB: add driver
for Meywa-Denki & Kayac YUREX") added the ID to hid_ignore_list.
I believe that we can distinguish YUREX and the Wireless Presenter by
device type. The patch below makes the driver ignore only YUREX
(bInterfaceProtocol==0), and recognize Wireless Presenter
(bInterfaceProtocol is keyboard or mouse) as generic HID. (I don't have
the Wireless Presenter, so not yet ested.)
** YUREX lsusb information:
Bus 002 Device 007: ID 0c45:1010 Microdia
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0c45 Microdia
idProduct 0x1010
bcdDevice 0.03
iManufacturer 1 JESS
iProduct 2 YUREX
iSerial 3 10000269
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 31
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=26922
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Reported-by: Thomas B?chler <thomas@archlinux.org>
Tested-by: Thomas B?chler <thomas@archlinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Per the HID Specification, Feature reports must be sent and received on
the Configuration endpoint (EP 0) through the Set_Report/Get_Report
interfaces. This patch adds two ioctls to hidraw to set and get feature
reports to and from the device. Modifications were made to hidraw and
usbhid.
New hidraw ioctls:
HIDIOCSFEATURE - Perform a Set_Report transfer of a Feature report.
HIDIOCGFEATURE - Perform a Get_Report transfer of a Feature report.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch doesn't alter functionality, but removes a dedicated kernel
thread.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Neaten current uses of dev_<level> by adding and using
hid specific hid_<level> macros.
Convert existing uses of dev_<level> uses to hid_<level>.
Convert hid-pidff printk uses to hid_<level>.
Remove err_hid and use hid_err instead.
Add missing newlines to logging messages where necessary.
Coalesce format strings.
Add and use pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Other miscellaneous changes:
Add const struct hid_device * argument to hid-core functions
extract() and implement() so hid_<level> can be used by them.
Fix bad indentation in hid-core hid_input_field function
that calls extract() function above.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
'roccat' into for-linus
|
|
Now that hiddev_driver isn't being used for anything, there's no
reason to keep it around. This patch (as1419) gets rid of it
entirely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
Added blank line after declarations.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Feature reports should only be sent on the control endpoint.
The USB HID standard is unclear and confusing on this issue. It seems to
suggest that Feature reports can be sent on a HID device's Interrupt OUT
endpoint. This cannot be the case because the report type is not encoded in
transfers sent out the Interrput OUT endpoint. If Feature reports were sent on
the Interrupt OUT endpint, they would be indistinguishable from Output reports
in the case where Report IDs were not used.
Further, Windows and Mac OS X do not send Feature reports out the interrupt OUT
Endpoint. They will only go out the Control Endpoint.
In addition, many devices simply do not hande Feature reports sent out the
Interrupt OUT endpoint.
Reported-by: simon@mungewell.org
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
My macbook infrared remote control was broken by commit
bd25f4dd6972755579d0ea50d1a5ace2e9b00d1a ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When I made commit 29129a98e6fc89 ("HID: Send Report ID when numbered
reports are sent over the control endpoint"), I didn't account for *buf
not being the report ID anymore, as buf is incremented.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Report ID wasn't sent as part of the payload for reports which were sent
over the control endpoint. This is required by section 8.1 of the HID spec.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (59 commits)
HID: fix up 'EMBEDDED' mess in Kconfig
HID: roccat: cleanup preprocessor macros
HID: roccat: refactor special event handling
HID: roccat: fix special button support
HID: roccat: Correctly mark init and exit functions
HID: hidraw: Use Interrupt Endpoint for OUT Transfers if Available
HID: hid-samsung: remove redundant key mappings
HID: add omitted hid-zydacron.c file
HID: hid-samsung: add support for Creative Desktop Wireless 6000
HID: picolcd: Eliminate use after free
HID: Zydacron Remote Control driver
HID: Use kmemdup
HID: magicmouse: fix input registration
HID: make Prodikeys driver standalone config option
HID: Prodikeys PC-MIDI HID Driver
HID: hidraw: fix indentation
HID: ntrig: add filtering module parameters
HID: ntrig: add sysfs access to filter parameters
HID: ntrig: add sensitivity and responsiveness support
HID: add multi-input quirk for eGalax Touchcontroller
...
|
|
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Conflicts:
drivers/hid/Makefile
|
|
'hid-suspend' into for-linus
|
|
Conflicts:
drivers/hid/hid-wacom.c
|
|
This patch makes the hidraw driver use the first Interrupt OUT endpoint for
HID transfers to the device if such an endpoint exists. This is consistent
with the behavior of the hiddev driver, and the logic is similar.
From the USB HID specification:
The Interrupt Out pipe is optional. If a device declares an Interrupt Out
endpoint then Output reports are transmitted by the host to the device
through the Interrupt Out endpoint. If no Interrupt Out endpoint is
declared then Output reports are transmitted to a device through the
Control endpoint, using Set_Report(Output) requests.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Although the usbhid driver allocates its usbhid structure in the probe
routine, several critical fields in that structure don't get
initialized until usbhid_start(). However if report descriptor
parsing fails then usbhid_start() is never called. This leads to
problems during system suspend -- the system will freeze.
This patch (as1378) fixes the bug by moving the initialization
statements up into usbhid_probe().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
Add suspend/resume hooks for HID drivers so these can do some
additional state adjustment when device gets suspended/resumed.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add two quirks to make it possible for usbhid module options to
override whether a device is ignored (HID_QUIRK_NO_IGNORE) and
whether to connect a hiddev device (HID_QUIRK_HIDDEV_FORCE).
Passing HID_QUIRK_NO_IGNORE for your device means that it will
not be ignored by the HID layer, even if present in a blacklist.
HID_QUIRK_HIDDEV_FORCE will force the creation of a hiddev for that
device, making it accessible from user-space.
Tested with an Apple IR Receiver, switching it from using appleir
to using lirc's macmini driver.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1365) enables remote wakeup by default for USB keyboard
devices. Keyboards in general are supposed to be wakeup devices, but
the correct place to enable it depends on the device's bus; no single
approach will work for all keyboard devices. In particular, this
covers only USB keyboards (and then only those supporting the boot
protocol).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add framebuffer support to PicoLCD device with use of deferred-io.
Only changed areas of framebuffer get sent to device in order to
save USB bandwidth and especially resources on PicoLCD device or
allow higher refresh rate for a small area. Changed tiles are
determined while updating shadow framebuffer.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
'apple_magic_mouse' into for-linus
Conflicts:
drivers/hid/Kconfig
|
|
Move the initialization of USB interface pointers from _start()
over to _probe() callback, which is where it belongs.
This fixes case where interface is NULL when parsing of report
descriptor fails.
LKML-Reference: <20100213135720.603e5f64@neptune.home>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some devices do not react to a control request (seen on APC UPS's) resulting in
a slow stream of messages, "generic-usb ... control queue full". Therefore
request needs a timeout.
Cc: stable@kernel.org
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In commit 2da31939a42 ("Bluetooth: Implement raw output support for HIDP
layer"), support for Bluetooth hid_output_raw_report was added, but it
pushes the data to the intr socket instead of the ctrl one. This has been
fixed by 6bf8268f9a91f1 ("Bluetooth: Use the control channel for raw HID reports")
Still, it is necessary to distinguish whether the report in question should be
either FEATURE or OUTPUT. For this, we have to extend the generic HID API,
so that hid_output_raw_report() callback provides means to specify this
value so that it can be passed down to lower level hardware drivers (currently
Bluetooth and USB).
Based on original patch by Bastien Nocera <hadess@hadess.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
