summaryrefslogtreecommitdiff
path: root/drivers/gpio/gpio-nomadik.c
AgeCommit message (Collapse)AuthorFilesLines
2012-05-11gpio: move the Nomadik GPIO driver to pinctrlLinus Walleij1-1306/+0
I'm moving this driver over to the pinctrl subsystem to convert the custom pin mux/config scheme over to use pinctrl. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-24drivers/gpio: gpio-nomadik: Add support for irqdomainsLee Jones1-48/+58
Add irq domain support to the gpio-nomadik GPIO driver. This enables its users to support dynamic IRQ assignment, which is requried by Device Tree. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-24drivers/gpio: gpio-nomadik: Apply Device Tree bindingsLee Jones1-3/+38
This creates Device Tree bindings for the Nomadik GPIO driver. Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-24gpio/nomadik: use ioremap() instead of static mappingsLinus Walleij1-4/+11
We were using a custom io_p2v() (physical-to-virtual) translation macro, but it's fully possible to just ioremap() this memory now, so skip use of static addresses altogether. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-23gpio/nomadik: support low EMI modeRabin Vincent1-0/+25
Low EMI (Electro-Magnetic Interference) mode means lower slew rate on the signals. The Nomadik GPIO controller supports this so create an interface to enable it. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-23gpio/nomadik: fix spurious interrupts with SKERabin Vincent1-0/+39
If the pin is switching to altfunc, and there was an interrupt installed on it which has been lazy disabled, actually mask the interrupt to prevent spurious interrupts that would occur while the pin is under control of the peripheral. Only SKE does this. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-23gpio/nomadik: cache [rf]w?imscRabin Vincent1-16/+26
Cache two more registers in the GPIO controller. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-04-23gpio/nomadik: don't set SLPM to 1 for non-wakeup pinsRabin Vincent1-14/+7
Setting GPIOs' SLPM value to 1 (WAKEUP_DISABLE) is seen to cause increased power consumption in sleep/deep-sleep. So remove the code which disables SLPM based on the wakeup settings and only ensure it is on as needed. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-12-12gpiolib: output basic details and consolidate gpio device driversGrant Likely1-2/+2
This patch adds a kernel message, containing GPIO range and device name on successful device registration, and removes duplicate messages from the following drivers: * gpio-adp5588 * gpio-bt8xx * gpio-cs5535 * gpio-janz-ttl * gpio-nomadik * gpio-pcf857x * gpio-xilinx * drivers/of/gpio.c Signed-off-by: Hartmut Knaack <knaack.h@gmx.de> [grant.likely@secretlab.ca: squashed 2 patches together] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-10-29Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6Linus Torvalds1-14/+113
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: h8300: Move gpio.h to gpio-internal.h gpio: pl061: add DT binding support gpio: fix build error in include/asm-generic/gpio.h gpiolib: Ensure struct gpio is always defined irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL gpio: langwell: ensure alternate function is cleared gpio-pch: Support interrupt function gpio-pch: Save register value in suspend() gpio-pch: modify gpio_nums and mask gpio-pch: support ML7223 IOH n-Bus gpio-pch: add spinlock in suspend/resume processing gpio-pch: Delete invalid "restore" code in suspend() gpio-ml-ioh: Fix suspend/resume issue gpio-ml-ioh: Support interrupt function gpio-ml-ioh: Delete unnecessary code gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler() gpio/nomadik: use genirq core to track enablement gpio/nomadik: disable clocks when unused
2011-09-20gpio/nomadik: use genirq core to track enablementLinus Walleij1-9/+2
Currently the Nomadik GPIO driver tracks enabled/disabled interrupt status with a local variable, switch to using the interrupt core. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-09-20gpio/nomadik: disable clocks when unusedRabin Vincent1-7/+113
The GPIO clock is required for register access and interrupt detection. When interrupt detection is not required on any of the pin in a block, the block's clock can be disabled when the registers are not being accessed. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> [Adjust for new IRQ chip core code, use only local functions] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-08-22ARM: 7032/1: plat-nomadik: break out GPIO driver specificsLinus Walleij1-0/+1
The <[plat|mach]/gpio.h> file is included from upper directories and deal with generic GPIO and gpiolib stuff. Break out the platform and driver specific defines and functions into its own header file. Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Alessandro Rubini <rubini@unipv.it> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-08-08ARM: gpio: nomadik: convert drivers to use asm/gpio.h rather than mach/gpio.hRussell King1-1/+1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-09gpio/nomadik: fix sleepmode for elder NomadikLinus Walleij1-11/+29
The mach-nomadik machine did not compile properly due to bad ux500-specific functions being called. Introduce new state variables to fix this up. Reported-by: Axel Lin <axel.lin@gmail.com> Cc: Alessandro Rubini <rubini@unipv.it> Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-26gpio/nomadik: add function to read GPIO pull down statusRickard Andersson1-4/+30
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com> Reviewed-by: Martin Persson <martin.persson@stericsson.com> [Split off from larger patch] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-26gpio/nomadik: show all pins in debugRabin Vincent1-4/+27
Useful to check the status of the runtime pin muxing. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> [Squashed, modified to use chip-internal IRQ trigger state] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-26gpio: move Nomadik GPIO driver to drivers/gpioGrant Likely1-0/+1020
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik and into the desired location indicated by the subsystem maintainer. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [grant.likely: squashed with kconfig fixup] Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 06:04:06 +0000