summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)AuthorFilesLines
2016-01-06Bluetooth: btmrvl: don't send data to firmware while processing suspendChin-Ran Lo3-3/+12
Usually when driver sends data to firmware it receives TX_DONE (DN_LD_HOST_INT_STATUS) interrupt from firmware right away. It's also observed that some times the fireware could delay sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to firmware during suspend processing and the TX_DONE interrupt is delayed, it may come back at wrong time when SDIO host driver is in the middle of suspending. Block any data from stack while suspending. Also skip sending data that are already in driver tx_queue. Don't purge the skb queue on suspend to avoid intermittent music after system resumes from S3. Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-06Bluetooth: btmrvl: max out host sleep parameter 'gap'Chin-Ran Lo1-1/+1
For gpio=0xff (wake up host through SDIO interface) case, gap=0xff means no delay (same as gap=0) for incoming data packet to be sent to host after host sleep is activated. Change it to the maximum delay to reduce the chance that RX interrupt could be delivered while host controller suspends. Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04Bluetooth: btmrvl: fix hung task warning dumpChin-Ran Lo1-1/+2
It's been observed that when bluetooth driver fails to activate the firmware, below hung task warning dump is displayed after 120 seconds. [ 36.461022] Bluetooth: vendor=0x2df, device=0x912e, class=255, fn=2 [ 56.512128] Bluetooth: FW failed to be active in time! [ 56.517264] Bluetooth: Downloading firmware failed! [ 240.252176] INFO: task kworker/3:2:129 blocked for more than 120 seconds. [ 240.258931] Not tainted 3.18.0 #254 [ 240.262972] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.270751] kworker/3:2 D ffffffc000205760 0 129 2 0x00000000 [ 240.277825] Workqueue: events request_firmware_work_func [ 240.283134] Call trace: [ 240.285581] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.290693] [<ffffffc00088dae0>] __schedule+0x540/0x7b8 [ 240.295921] [<ffffffc00088ddd0>] schedule+0x78/0x84 [ 240.300764] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8 [ 240.306395] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84 [ 240.311840] [<ffffffbffc163d08>] 0xffffffbffc163d08 [ 240.316685] [<ffffffbffc165104>] 0xffffffbffc165104 [ 240.321524] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex] [ 240.327918] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex] [ 240.334741] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80 [ 240.341127] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c [ 240.346831] [<ffffffc00023c6a0>] worker_thread+0x350/0x470 [ 240.352272] [<ffffffc0002419bc>] kthread+0xf0/0xfc [ 240.357019] 2 locks held by kworker/3:2/129: [ 240.361248] #0: ("events"){.+.+.+}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c [ 240.369562] #1: ((&fw_work->work)){+.+.+.}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c [ 240.378589] task PC stack pid father [ 240.384501] kworker/1:1 D ffffffc000205760 0 40 2 0x00000000 [ 240.391524] Workqueue: events mtk_atomic_work [ 240.395884] Call trace: [ 240.398317] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.403448] [<ffffffc00027279c>] lock_acquire+0x128/0x164 [ 240.408821] kworker/3:2 D ffffffc000205760 0 129 2 0x00000000 [ 240.415867] Workqueue: events request_firmware_work_func [ 240.421138] Call trace: [ 240.423589] [<ffffffc000205760>] __switch_to+0x80/0x8c [ 240.428688] [<ffffffc00088dae0>] __schedule+0x540/0x7b8 [ 240.433886] [<ffffffc00088ddd0>] schedule+0x78/0x84 [ 240.438732] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8 [ 240.444361] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84 [ 240.449801] [<ffffffbffc163d08>] 0xffffffbffc163d08 [ 240.454649] [<ffffffbffc165104>] 0xffffffbffc165104 [ 240.459486] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex] [ 240.465882] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex] [ 240.472705] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80 [ 240.479090] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c [ 240.484794] [<ffffffc00023c6a0>] worker_thread+0x350/0x470 [ 240.490231] [<ffffffc0002419bc>] kthread+0xf0/0xfc This patch adds missing sdio_release_host() call so that wlan driver thread can claim sdio host. Fixes: 4863e4cc31d647e1 ("Bluetooth: btmrvl: release sdio bus after firmware is up") Signed-off-by: Chin-Ran Lo <crlo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04Bluetooth: hci_bcm: new ACPI IDsHeikki Krogerus1-0/+3
These are used at least by Acer with BCM43241. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04Bluetooth: hci_bcm: move all Broadcom ACPI IDs to BCM HCI driverHeikki Krogerus1-0/+4
The IDs should all be for Broadcom BCM43241 module, and hci_bcm is now the proper driver for them. This removes one of two different ways of handling PM with the module. Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22Bluetooth: bfusb: Fix the return error codeSyam Sidhardhan1-1/+1
-ENOMEM is the appropriate error code instead of -EIO. Signed-off-by: Syam Sidhardhan <s.syam@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22Bluetooth: bfusb: Remove redundant error messageSyam Sidhardhan1-3/+1
devm_kzalloc prints its own OOM message upon failure. Signed-off-by: Syam Sidhardhan <s.syam@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22Bluetooth: bcm203x: Remove redundant error messageSyam Sidhardhan1-3/+1
devm_kzalloc prints its own OOM message upon failure. Signed-off-by: Syam Sidhardhan <s.syam@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-20Bluetooth: hci_bcm: Add BCM2E65 ACPI IDLuka Karinja1-0/+1
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF. Signed-off-by: Luka Karinja <luka.karinja@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: h5: Do not initialize Configuration fieldAndrei Emeltchenko1-2/+2
Initializing Configuration field in H5 Config message to 0x01 gives wrong impression that the value is used and needed. Later on the whole field is rewritten with h5_cfg_field(). Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: btintel: Create common Intel Version Read functionLoic Poulain4-92/+66
The Intel Version Read command is used to retrieve information about hardware and firmware version/revision of Intel Bluetooth controllers. This is an Intel generic command used in USB and UART drivers. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: btintel: Add manufacturing enter/exit helpersLoic Poulain3-94/+86
Older Intel controllers need to enter manufacturing mode to perform some vendor specific operations (patching, configuration...). Add enter/exit manufaturing methods and refactor existing manufacturing code. Exit can be configured to perform a reset. Reset can be performed either with patches activated or deactivated. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Add support of Toshiba Broadcom based devicesDmitry Tunin1-0/+4
BugLink: https://bugs.launchpad.net/bugs/1522949 T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0225 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=4CBB58034671 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-12-10Bluetooth: hci_intel: Use shorter timeout for HCI commandsLoic Poulain1-4/+4
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of HCI_INIT_TIMEOUT(10s) which is not justified in these cases. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: hci_ldisc: Remove dead codePeter Hurley1-7/+1
The N_HCI ldisc does not define a flush_buffer() ldisc method, so the check when opening the ldisc is always false. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Simplify setting Configuration FieldAndrei Emeltchenko1-5/+1
Only Sliding Window Size is used at the moment for H5 Bluetooth Configuration messages. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Use hexadecimal notation for maskAndrei Emeltchenko1-1/+1
Using hexadecimal notation for mask makes code easier to read Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19Bluetooth: Use hex notation for maskAndrei Emeltchenko1-1/+1
This makes it easier to read and makes code consistent. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19Bluetooth: Fix mask for H5 header lenAndrei Emeltchenko1-1/+1
Fixes mask when calculating three-wire (h5) length. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19Bluetooth: Use new hci_skb_pkt_* wrappers for driversMarcel Holtmann21-116/+127
The new hci_skb_pkt_* wrappers are mainly intented for drivers to require less knowledge about bt_cb(sbk) handling. So after converting the core packet handling, convert all drivers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-11-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds1-2/+4
Pull networking fixes from David Miller: 1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet. 2) Several spots need to get to the original listner for SYN-ACK packets, most spots got this ok but some were not. Whilst covering the remaining cases, create a helper to do this. From Eric Dumazet. 3) Missiing check of return value from alloc_netdev() in CAIF SPI code, from Rasmus Villemoes. 4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich. 5) Use after free in mvneta driver, from Justin Maggard. 6) Fix race on dst->flags access in dst_release(), from Eric Dumazet. 7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd Bergmann. 8) Fix multicast getsockopt deadlock, from WANG Cong. 9) Fix deadlock in btusb, from Kuba Pawlak. 10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6 counter state. From Sabrina Dubroca. 11) Fix packet_bind() race, which can cause lost notifications, from Francesco Ruggeri. 12) Fix MAC restoration in qlcnic driver during bonding mode changes, from Jarod Wilson. 13) Revert bridging forward delay change which broke libvirt and other userspace things, from Vlad Yasevich. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits) Revert "bridge: Allow forward delay to be cfgd when STP enabled" bpf_trace: Make dependent on PERF_EVENTS qed: select ZLIB_INFLATE net: fix a race in dst_release() net: mvneta: Fix memory use after free. net: Documentation: Fix default value tcp_limit_output_bytes macvtap: Resolve possible __might_sleep warning in macvtap_do_read() mvneta: add FIXED_PHY dependency net: caif: check return value of alloc_netdev net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA drivers: net: xgene: fix RGMII 10/100Mb mode netfilter: nft_meta: use skb_to_full_sk() helper net_sched: em_meta: use skb_to_full_sk() helper sched: cls_flow: use skb_to_full_sk() helper netfilter: xt_owner: use skb_to_full_sk() helper smack: use skb_to_full_sk() helper net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid() bpf: doc: correct arch list for supported eBPF JIT dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put" bonding: fix panic on non-ARPHRD_ETHER enslave failure ...
2015-11-04Merge tag 'driver-core-4.4-rc1' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of debugfs updates, with a smattering of minor driver core fixes and updates as well. All have been in linux-next for a long time" * tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: debugfs: Add debugfs_create_ulong() of: to support binding numa node to specified device in devicetree debugfs: Add read-only/write-only bool file ops debugfs: Add read-only/write-only size_t file ops debugfs: Add read-only/write-only x64 file ops debugfs: Consolidate file mode checks in debugfs_create_*() Revert "mm: Check if section present during memory block (un)registering" driver-core: platform: Provide helpers for multi-driver modules mm: Check if section present during memory block (un)registering devres: fix a for loop bounds check CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit base/platform: assert that dev_pm_domain callbacks are called unconditionally sysfs: correctly handle short reads on PREALLOC attrs. base: soc: siplify ida usage kobject: move EXPORT_SYMBOL() macros next to corresponding definitions kobject: explain what kobject's sd field is debugfs: document that debugfs_remove*() accepts NULL and error values debugfs: Pass bool pointer to debugfs_create_bool() ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
2015-11-05Bluetooth: Fix possible deadlock in btusbKuba Pawlak1-2/+4
commit 8f9d02f470f48416444ac3a1eacecdd0f743f1a7 introduced spinlocks in btusb_work. This is run in a context of a worqueue and can be interrupted by hardware irq. If it happens while spinlock is held, we have a deadlock. Solution is to use _irqsave/_resore version of locking [ 466.460560] ================================= [ 466.460565] [ INFO: inconsistent lock state ] [ 466.460572] 4.3.0-rc6+ #1 Tainted: G W [ 466.460576] --------------------------------- [ 466.460582] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. [ 466.460589] kworker/0:2/94 [HC0[0]:SC0[0]:HE1:SE1] takes: [ 466.460595] (&(&data->rxlock)->rlock){?.-...}, at: [<ffffffffa0526923>] btusb_work+0xa3/0x3fd [btusb] [ 466.460621] {IN-HARDIRQ-W} state was registered at: [ 466.460625] [<ffffffff811021b5>] __lock_acquire+0xc45/0x1e80 [ 466.460638] [<ffffffff811040d5>] lock_acquire+0xe5/0x1f0 [ 466.460646] [<ffffffff8182f108>] _raw_spin_lock+0x38/0x50 [ 466.460657] [<ffffffffa0525448>] btusb_recv_intr+0x38/0x170 [btusb] [ 466.460668] [<ffffffffa0525626>] btusb_intr_complete+0xa6/0x130 [btusb] [ 466.460679] [<ffffffff815d8f1e>] __usb_hcd_giveback_urb+0x8e/0x160 [ 466.460690] [<ffffffff815d911f>] usb_hcd_giveback_urb+0x3f/0x120 [ 466.460698] [<ffffffff81606e4d>] uhci_giveback_urb+0xad/0x280 [ 466.460706] [<ffffffff81608f64>] uhci_scan_schedule.part.33+0x6b4/0xbe0 [ 466.460714] [<ffffffff81609b50>] uhci_irq+0xd0/0x180 [ 466.460722] [<ffffffff815d8296>] usb_hcd_irq+0x26/0x40 [ 466.460729] [<ffffffff81117d40>] handle_irq_event_percpu+0x40/0x300 [ 466.460739] [<ffffffff81118040>] handle_irq_event+0x40/0x60 [ 466.460746] [<ffffffff8111af39>] handle_fasteoi_irq+0x89/0x150 [ 466.460754] [<ffffffff8101e0f3>] handle_irq+0x73/0x120 [ 466.460763] [<ffffffff81832f11>] do_IRQ+0x61/0x120 [ 466.460772] [<ffffffff8183084c>] ret_from_intr+0x0/0x31 [ 466.460780] [<ffffffff81697a77>] cpuidle_enter+0x17/0x20 [ 466.460790] [<ffffffff810f62c2>] call_cpuidle+0x32/0x60 [ 466.460800] [<ffffffff810f65a8>] cpu_startup_entry+0x2b8/0x3f0 [ 466.460807] [<ffffffff818214ca>] rest_init+0x13a/0x140 [ 466.460817] [<ffffffff81f76029>] start_kernel+0x4a3/0x4c4 [ 466.460827] [<ffffffff81f75339>] x86_64_start_reservations+0x2a/0x2c [ 466.460837] [<ffffffff81f75485>] x86_64_start_kernel+0x14a/0x16d [ 466.460846] irq event stamp: 754913 [ 466.460851] hardirqs last enabled at (754913): [<ffffffff8182f4cc>] _raw_spin_unlock_irq+0x2c/0x40 [ 466.460861] hardirqs last disabled at (754912): [<ffffffff8182f28d>] _raw_spin_lock_irq+0x1d/0x60 [ 466.460869] softirqs last enabled at (753024): [<ffffffff810aeaa0>] __do_softirq+0x380/0x490 [ 466.460880] softirqs last disabled at (753009): [<ffffffff810aedef>] irq_exit+0x10f/0x120 [ 466.460888] other info that might help us debug this: [ 466.460894] Possible unsafe locking scenario: [ 466.460899] CPU0 [ 466.460903] ---- [ 466.460907] lock(&(&data->rxlock)->rlock); [ 466.460915] <Interrupt> [ 466.460918] lock(&(&data->rxlock)->rlock); [ 466.460926] *** DEADLOCK *** [ 466.460935] 2 locks held by kworker/0:2/94: [ 466.460939] #0: ("events"){.+.+.+}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660 [ 466.460958] #1: ((&data->work)){+.+...}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660 [ 466.460974] Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-25Bluetooth: btmrvl: add missing of_node_putJulia Lawall1-1/+4
for_each_compatible_node performs an of_node_get on each iteration, so a break out of the loop requires an of_node_put. A simplified version of the semantic patch that fixes this problem is as follows (http://coccinelle.lip6.fr): // <smpl> @@ expression e; local idexpression n; @@ for_each_compatible_node(n, ...) { ... when != of_node_put(n) when != e = n ( return n; | + of_node_put(n); ? return ...; ) ... } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-22Bluetooth: hci_bcm: checking for ERR_PTR instead of NULLDan Carpenter1-2/+2
bt_skb_alloc() returns NULL on error, it never returns an ERR_PTR. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btintel: Enable extra Intel vendor eventsMarcel Holtmann3-9/+92
The Intel Bluetooth controllers can emit extra vendor specific events in error conditions or for debugging purposes. To make the life easier for engineers, enable them by default. When the vendor_diag options has been enabled, then additional debug events are also enabled. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Set manufacturer for Intel bootloader devicesMarcel Holtmann1-1/+3
For Intel bootloader devices, set the manufacturer information so that it becomes possible to decode the boot process. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: hci_uart: Provide initial manufacturer informationMarcel Holtmann6-0/+12
Provide an early indication about the manufacturer information so that it can be forwarded into monitor channel. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Add support for latest Apple controllersMarcel Holtmann1-7/+15
The latest Apple Bluetooth controllers with Broadcom chip in it have a small design change. Instead of including a USB hub with mouse and keyboard devices, they are now HID interfaces on the same device. T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 39 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=05ac ProdID=8290 Rev= 0.79 S: Manufacturer=Broadcom Corp. S: Product=Bluetooth USB Host Controller C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA A: FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=10ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) The general layout of Bluetooth devices is that interface 0 is the main interface and interface 1 is for audio data. This design obviously moves it to main interface 2 and audio data on interface 3. Starting with the MacBookPro12,1 (early 2015 models) the new Broadcom BCM943602CS cards are used which show this interface layout. usb 4-1.5: New USB device found, idVendor=05ac, idProduct=8290 usb 4-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-1.5: Product: Bluetooth USB Host Controller usb 4-1.5: Manufacturer: Broadcom Corp. Bluetooth: hci0: BCM: chip id 102 build 0243 Bluetooth: hci0: BCM: product 05ac:8290 Bluetooth: hci0: BCM20703A1 Generic USB UHE Apple 20Mhz fcbga_X87 Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Set early vendor info for Intel and BroadcomMarcel Holtmann1-0/+4
For the controllers from Intel and Broadcom (including Apple), it is helpful to have the information about the manufacturer send out early. This patch sets the hdev->manufacturer information which will be send out before actually calling the vendor specific hdev->setup driver callback. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: ath3k: Add support of AR3012 0cf3:817b deviceDmitry Tunin2-0/+3
T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=817b Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1506615 Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-10-21Bluetooth: ath3k: Add new AR3012 0930:021c idDmitry Tunin2-0/+3
This adapter works with the existing linux-firmware. T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=021c Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1502781 Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-10-21Bluetooth: btusb: Add support for Foxconn/Lenovo BCM43142A0 (105b:e065)Santtu Rekilä1-0/+3
Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop and noticed it doesn't work automatically, because the USB IDs are missing from btusb.c. Plugging in the adapter on Linux 4.1 (dmesg): usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065 usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-3.3.3: Product: BCM43142A0 usb 3-3.3.3: Manufacturer: Broadcom Corp usb 3-3.3.3: SerialNumber: 0090A286559E /sys/kernel/debug/usb/devices: T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=105b ProdID=e065 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=0090A286559E C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Support for the chipset was added in commit 88f9b65 and a similar BCM43142 based device was added in commit 8f0c304. To work around the issue, I got the firmware (BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it in /lib/firmware/brcm/BCM.hcd. After that: $ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id ...(plug in the adapter) usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065 usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-3.3.3: Product: BCM43142A0 usb 3-3.3.3: Manufacturer: Broadcom Corp usb 3-3.3.3: SerialNumber: 0090A286559E Bluetooth: hci0: BCM: chip id 70 Bluetooth: hci0: BCM (001.001.011) build 0000 bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd Bluetooth: hci0: BCM (001.001.011) build 0154 Bam, now it works for me! /sys/kernel/debug/usb/devices: T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=105b ProdID=e065 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=0090A286559E C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Santtu Rekilä <sare@r00t3d.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btbcm: Read USB product information for Apple devicesMarcel Holtmann1-0/+9
For the Apple Bluetooth devices, read the USB product information and print them. This allows for easy mapping of chip and USB details. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btbcm: Fix firmware version number calculationMarcel Holtmann1-4/+4
The calculation for the firmware version number is off by one bit. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Mark BCM2045 devices to have broken link key commandsMarcel Holtmann1-0/+7
The BCM2045 seems to have a problem with the stored link key commands and thus just mark them as broken. HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 status 0x00 Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80 HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 status 0x00 HCI Version: 2.0 (0x3) HCI Revision: 0x2000 LMP Version: 2.0 (0x3) LMP Subversion: 0x410d Manufacturer: Broadcom Corporation (15) HCI Event: Command Complete (0x0e) plen 11 Read Buffer Size (0x04|0x0005) ncmd 1 status 0x00 ACL MTU 1017:8 SCO MTU 64:0 HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 status 0x00 Commands: ffffff03feffcfffffffffff0300f8ff07 HCI Event: Command Complete (0x0e) plen 4 Delete Stored Link Key (0x03|0x0012) ncmd 1 status 0x11 deleted 2048 Error: Unsupported Feature or Parameter Value From the looks of it, this device seems genuine and not one of the devices that are neither Broadcom nor CSR devices in reality. T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=2045 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM2045A S: SerialNumber=000000000000 C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none) Reported-and-tested-by: Julio González Mejías <juliolokooo@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Add diagnostic support for older controllersMarcel Holtmann3-0/+44
For the older controllers like Wilkens Peak and Stone Peak, enabling the traces requires to switch into manufacturer mode first. This patch does exactly that, but only for these older controllers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Set quirk for non-persistent diagnostic settingsMarcel Holtmann2-3/+3
For Intel controllers the diagnostics settings are not persistent over HCI Reset. So set the quirk to programm them again on every power up. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: bpa10x: fix BT_HCIUART dependencyArnd Bergmann1-2/+1
The change to bpa10x to use the h4_recv_buf helper added a dependency on BT_HCIUART. This was incorrectly added to Kconfig by adding a 'select' statement, which now in turn causes build failures when CONFIG_TTY is not set: warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY) vers/built-in.o: In function `hci_uart_tty_receive': fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle' drivers/built-in.o: In function `hci_uart_tty_ioctl': fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper' drivers/built-in.o: In function `hci_uart_flush': This replaces the 'select BT_HCIUART' dependency with 'depends on', which does not have this kind of problem. Alternatively, one could add 'depends on TTY', but avoiding 'select' on user-visible options is generally the preferred choice as that does not introduce the potential for dependency loops or incomplete dependency chains. Fixes: 91489919247a ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency") Fixes: 943cc592195e ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21Bluetooth: btusb: Print information of Intel SfP lock statesMarcel Holtmann1-0/+9
The lock states from Intel SfP controllers can only be read once before loading the firmware. So for debugging purposes, print them out. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btintel: Add support for enabling tracing functionalityMarcel Holtmann4-0/+40
For Intel controllers with firmware that allows tracing of baseband functionality this allows enabling it via set_diag driver callback. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: btusb: Add support for Broadcom LM_DIAG interfaceMarcel Holtmann1-4/+224
The Broadcom Bluetooth USB devices have a third interface that is dedicated for LM_DIAG messages. The If#= 2 describes this interface and it consists of one bulk in and one bulk endpoint. T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=19ff ProdID=0239 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) For all Broadcom based devices with this interface, the driver now claims it and schedules URBs for it. This allows to capture the LM_DIAG messages and allows forwarding them via hci_recv_diag into the diagnostic channel of the Bluetooth subsystem. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21Bluetooth: bpa10x: Fix missing BT_HCIUART dependencyMarcel Holtmann1-0/+1
Selecting just BT_HCIUART_H4 is not enough and it also needs to select BT_HCIUART to avoid this warning: warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct dependencies (NET && BT && BT_HCIUART) Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassemblyMarcel Holtmann3-109/+29
The manually coded frame reassembly is actually broken. The h4_recv_buf helper from the UART driver is a perfect fit for frame reassembly for this driver. So just export that function and use it here as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: bpa10x: Add support for set_diag driver callbackMarcel Holtmann1-0/+20
The BPA-10x devices support tracing operation. Use the set_diag driver callback to allow enabling and disabling that functionality. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: bpa10x: Read revision information in setup stageMarcel Holtmann1-0/+19
For debugging pruposes, read the revision string of the BPA-10x devices and print it. For example one of the latest devices respond with the string SNIF_102,BB930,02/01/18,10:37:56. < HCI Command: Vendor (0x3f|0x000e) plen 1 07 . > HCI Event: Command Complete (0x0e) plen 49 Vendor (0x3f|0x000e) ncmd 1 Status: Success (0x00) 53 4e 49 46 5f 31 30 32 2c 42 42 39 33 30 2c 30 SNIF_102,BB930,0 32 2f 30 31 2f 31 38 2c 31 30 3a 33 37 3a 35 36 2/01/18,10:37:56 00 00 00 00 00 00 00 00 00 00 00 00 00 ............. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: hci_bcm: Enable support for set_diag driver callbackMarcel Holtmann1-0/+24
The set_diag driver callback allows enabling and disabling the vendor specific diagnostic information. Since Broadcom chips have support for a dedicated LM_DIAG channel, hook it up accordingly. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08Bluetooth: hci_bcm: Enable parsing of LM_DIAG messagesMarcel Holtmann1-3/+14
The Broadcom UART based controllers can send LM_DIAG messages with the identifier 0x07 inside the HCI stream. These messages are 63 octets in size and have no variable payload or length indicator. This patch adds correct parsing information for the h4_recv_buf handler and in case these packets are received, they are forwarded to the Bluetooth core via hci_recv_diag interface. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-07Bluetooth: btbcm: Read the local name in setup stageMarcel Holtmann1-0/+44
The Broadcom Bluetooth controllers have the chip name included in the ROM firmware or later in the patchram firmware. For debugging purposes read the local name and print it out. This is only done during setup stage and only once before loading the firmware and once after loading the firmware. For the Broadcom based controllers from Apple, the name is only read once after determining the chip id. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05Bluetooth: Move handling of HCI_RUNNING flag into coreMarcel Holtmann12-82/+1
Setting and clearing of HCI_RUNNING flag in each and every driver is just duplicating the same code all over the place. So instead of having the driver do it in their hdev->open and hdev->close callbacks, set it globally in the core transport handling. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 17:46:27 +0000