| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
|
|
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
arm64: defconfig: Enable Broadcom's GENET Ethernet controller
ARM: multi_v7_defconfig: Enable devfreq thermal integration
ARM: exynos_defconfig: Enable devfreq thermal integration
ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
arm64: defconfig: Enable Actions Semi specific drivers
arm64: defconfig: Enable Broadcom's STB PCIe controller
arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
ARM: configs: at91: enable config flags for sam9x60 SoC
ARM: configs: at91: use savedefconfig
arm64: defconfig: Enable tegra XUDC support
ARM: defconfig: gemini: Update defconfig
arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
arm64: defconfig: enable CONFIG_QCOM_CPR
arm64: defconfig: Enable HFPLL
arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
ARM: imx_v6_v7_defconfig: Select the TFP410 driver
ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
arm64: defconfig: Enable ATH10K_SNOC
...
|
|
Pull ARM Device-tree updates from Olof Johansson:
"New SoCs:
- Atmel/Microchip SAM9X60 (ARM926 SoC)
- OMAP 37xx gets split into AM3703/AM3715/DM3725, who are all
variants of it with different GPU/media IP configurations.
- ST stm32mp15 SoCs (1-2 Cortex-A7, CAN, GPU depending on SKU)
- ST Ericsson ab8505 (variant of ab8500) and db8520 (variant of
db8500)
- Unisoc SC9863A SoC (8x Cortex-A55 mobile chipset w/ GPU, modem)
- Qualcomm SC7180 (8-core 64bit SoC, unnamed CPU class)
New boards:
- Allwinner:
+ Emlid Neutis SoM (H3 variant)
+ Libre Computer ALL-H3-IT
+ PineH64 Model B
- Amlogic:
+ Libretech Amlogic GX PC (s905d and s912-based variants)
- Atmel/Microchip:
+ Kizboxmini, sam9x60 EK, sama5d27 Wireless SOM (wlsom1)
- Marvell:
+ Armada 385-based SolidRun Clearfog GTR
- NXP:
+ Gateworks GW59xx boards based on i.MX6/6Q/6QDL
+ Tolino Shine 3 eBook reader (i.MX6sl)
+ Embedded Artists COM (i.MX7ULP)
+ SolidRun CLearfog CX/ITX and HoneyComb (LX2160A-based systems)
+ Google Coral Edge TPU (i.MX8MQ)
- Rockchip:
+ Radxa Dalang Carrier (supports rk3288 and rk3399 SOMs)
+ Radxa Rock Pi N10 (RK3399Pro-based)
+ VMARC RK3399Pro SOM
- ST:
+ Reference boards for stm32mp15
- ST Ericsson:
+ Samsung Galaxy S III mini (GT-I8190)
+ HREF520 reference board for DB8520
- TI OMAP:
+ Gen1 Amazon Echo (OMAP3630-based)
- Qualcomm:
+ Inforce 6640 Single Board Computer (msm8996-based)
+ SC7180 IDP (SC7180-based)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (623 commits)
dt-bindings: fix compilation error of the example in marvell,mmp3-hsic-phy.yaml
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
ARM: dts: aspeed: rainier: Add UCD90320 power sequencer
ARM: dts: aspeed: rainier: Switch PSUs to unknown version
arm64: dts: rockchip: Kill off "simple-panel" compatibles
ARM: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
ARM: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: exynos: Rename Samsung and Exynos to lowercase
arm64: dts: uniphier: add reset-names to NAND controller node
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes for 5.6, take #1 from Marc Zyngier:
- Guarantee allocation of L2 vPE table for GICv4.1
- Fix GICv4.1 VPROPBASER programming
- Numerous GICv4.1 tidy ups
- Fix disabled GICv3 redistributor provisioning with ACPI
- KConfig cleanup for C-SKY
|
|
V{PEND,PROP}BASER registers are actually located in VLPI_base frame
of the *redistributor*. Rename their accessors to reflect this fact.
No functional changes.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200206075711.1275-7-yuzenghui@huawei.com
|
|
Pull ARM updates from Russell King:
- decompressor updates
- prevention of out-of-bounds access while stacktracing
- fix a section mismatch warning with free_memmap()
- make kexec depend on MMU to avoid some build errors
- remove swapops stubs
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8954/1: NOMMU: remove stubs for swapops
ARM: 8952/1: Disable kmemleak on XIP kernels
ARM: 8951/1: Fix Kexec compilation issue.
ARM: 8949/1: mm: mark free_memmap as __init
ARM: 8948/1: Prevent OOB access in stacktrace
ARM: 8945/1: decompressor: use CONFIG option instead of cc-option
ARM: 8942/1: Revert "8857/1: efi: enable CP15 DMB instructions before cleaning the cache"
ARM: 8941/1: decompressor: enable CP15 barrier instructions in v7 cache setup code
|
|
Merge more updates from Andrew Morton:
"The rest of MM and the rest of everything else: hotfixes, ipc, misc,
procfs, lib, cleanups, arm"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
ARM: dma-api: fix max_pfn off-by-one error in __dma_supported()
treewide: remove redundant IS_ERR() before error code check
include/linux/cpumask.h: don't calculate length of the input string
lib: new testcases for bitmap_parse{_user}
lib: rework bitmap_parse()
lib: make bitmap_parse_user a wrapper on bitmap_parse
lib: add test for bitmap_parse()
bitops: more BITS_TO_* macros
lib/string: add strnchrnul()
proc: convert everything to "struct proc_ops"
proc: decouple proc from VFS with "struct proc_ops"
asm-generic/tlb: provide MMU_GATHER_TABLE_FREE
asm-generic/tlb: rename HAVE_MMU_GATHER_NO_GATHER
asm-generic/tlb: rename HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: rename HAVE_RCU_TABLE_FREE
asm-generic/tlb: add missing CONFIG symbol
asm-gemeric/tlb: remove stray function declarations
asm-generic/tlb: avoid potential double flush
mm/mmu_gather: invalidate TLB correctly on batch allocation failure and flush
powerpc/mmu_gather: enable RCU_TABLE_FREE even for !SMP case
...
|
|
max_pfn, as set in arch/arm/mm/init.c:
static void __init find_limits(unsigned long *min,
unsigned long *max_low,
unsigned long *max_high)
{
*max_low = PFN_DOWN(memblock_get_current_limit());
*min = PFN_UP(memblock_start_of_DRAM());
*max_high = PFN_DOWN(memblock_end_of_DRAM());
}
with memblock_end_of_DRAM() pointing to the next byte after DRAM. As
such, max_pfn points to the PFN after the end of DRAM.
Thus when using max_pfn to check DMA masks, we should subtract one when
checking DMA ranges against it.
Commit 8bf1268f48ad ("ARM: dma-api: fix off-by-one error in
__dma_supported()") fixed the same issue, but missed this spot.
This issue was found while working on the sun4i-csi v4l2 driver on the
Allwinner R40 SoC. On Allwinner SoCs, DRAM is offset at 0x40000000, and
we are starting to use of_dma_configure() with the "dma-ranges" property
in the device tree to have the DMA API handle the offset.
In this particular instance, dma-ranges was set to the same range as the
actual available (2 GiB) DRAM. The following error appeared when the
driver attempted to allocate a buffer:
sun4i-csi 1c09000.csi: Coherent DMA mask 0x7fffffff (pfn 0x40000-0xc0000)
covers a smaller range of system memory than the DMA zone pfn 0x0-0xc0001
sun4i-csi 1c09000.csi: dma_alloc_coherent of size 307200 failed
Fixing the off-by-one error makes things work.
Link: http://lkml.kernel.org/r/20191224030239.5656-1-wens@kernel.org
Fixes: 11a5aa32562e ("ARM: dma-mapping: check DMA mask against available memory")
Fixes: 9f28cde0bc64 ("ARM: another fix for the DMA mapping checks")
Fixes: ab746573c405 ("ARM: dma-mapping: allow larger DMA mask than supported")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.
Conversion rule is:
llseek => proc_lseek
unlocked_ioctl => proc_ioctl
xxx => proc_xxx
delete ".owner = THIS_MODULE" line
[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As described in the comment, the correct order for freeing pages is:
1) unhook page
2) TLB invalidate page
3) free page
This order equally applies to page directories.
Currently there are two correct options:
- use tlb_remove_page(), when all page directores are full pages and
there are no futher contraints placed by things like software
walkers (HAVE_FAST_GUP).
- use MMU_GATHER_RCU_TABLE_FREE and tlb_remove_table() when the
architecture does not do IPI based TLB invalidate and has
HAVE_FAST_GUP (or software TLB fill).
This however leaves architectures that don't have page based directories
but don't need RCU in a bind. For those, provide MMU_GATHER_TABLE_FREE,
which provides the independent batching for directories without the
additional RCU freeing.
Link: http://lkml.kernel.org/r/20200116064531.483522-10-aneesh.kumar@linux.ibm.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Towards a more consistent naming scheme.
[akpm@linux-foundation.org: fix sparc64 Kconfig]
Link: http://lkml.kernel.org/r/20200116064531.483522-7-aneesh.kumar@linux.ibm.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For arm pmd_large() already exists and does what we want. So simply
provide the generic pmd_leaf() name.
Link: http://lkml.kernel.org/r/20191218162402.45610-4-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
|
|
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for Linux 5.6
- Fix MMIO sign extension
- Fix HYP VA tagging on tag space exhaustion
- Fix PSTATE/CPSR handling when generating exception
- Fix MMU notifier's advertizing of young pages
- Fix poisoned page handling
- Fix PMU SW event handling
- Fix TVAL register access
- Fix AArch32 external abort injection
- Fix ITS unmapped collection handling
- Various cleanups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread management updates from Christian Brauner:
"Sargun Dhillon over the last cycle has worked on the pidfd_getfd()
syscall.
This syscall allows for the retrieval of file descriptors of a process
based on its pidfd. A task needs to have ptrace_may_access()
permissions with PTRACE_MODE_ATTACH_REALCREDS (suggested by Oleg and
Andy) on the target.
One of the main use-cases is in combination with seccomp's user
notification feature. As a reminder, seccomp's user notification
feature was made available in v5.0. It allows a task to retrieve a
file descriptor for its seccomp filter. The file descriptor is usually
handed of to a more privileged supervising process. The supervisor can
then listen for syscall events caught by the seccomp filter of the
supervisee and perform actions in lieu of the supervisee, usually
emulating syscalls. pidfd_getfd() is needed to expand its uses.
There are currently two major users that wait on pidfd_getfd() and one
future user:
- Netflix, Sargun said, is working on a service mesh where users
should be able to connect to a dns-based VIP. When a user connects
to e.g. 1.2.3.4:80 that runs e.g. service "foo" they will be
redirected to an envoy process. This service mesh uses seccomp user
notifications and pidfd to intercept all connect calls and instead
of connecting them to 1.2.3.4:80 connects them to e.g.
127.0.0.1:8080.
- LXD uses the seccomp notifier heavily to intercept and emulate
mknod() and mount() syscalls for unprivileged containers/processes.
With pidfd_getfd() more uses-cases e.g. bridging socket connections
will be possible.
- The patchset has also seen some interest from the browser corner.
Right now, Firefox is using a SECCOMP_RET_TRAP sandbox managed by a
broker process. In the future glibc will start blocking all signals
during dlopen() rendering this type of sandbox impossible. Hence,
in the future Firefox will switch to a seccomp-user-nofication
based sandbox which also makes use of file descriptor retrieval.
The thread for this can be found at
https://sourceware.org/ml/libc-alpha/2019-12/msg00079.html
With pidfd_getfd() it is e.g. possible to bridge socket connections
for the supervisee (binding to a privileged port) and taking actions
on file descriptors on behalf of the supervisee in general.
Sargun's first version was using an ioctl on pidfds but various people
pushed for it to be a proper syscall which he duely implemented as
well over various review cycles. Selftests are of course included.
I've also added instructions how to deal with merge conflicts below.
There's also a small fix coming from the kernel mentee project to
correctly annotate struct sighand_struct with __rcu to fix various
sparse warnings. We've received a few more such fixes and even though
they are mostly trivial I've decided to postpone them until after -rc1
since they came in rather late and I don't want to risk introducing
build warnings.
Finally, there's a new prctl() command PR_{G,S}ET_IO_FLUSHER which is
needed to avoid allocation recursions triggerable by storage drivers
that have userspace parts that run in the IO path (e.g. dm-multipath,
iscsi, etc). These allocation recursions deadlock the device.
The new prctl() allows such privileged userspace components to avoid
allocation recursions by setting the PF_MEMALLOC_NOIO and
PF_LESS_THROTTLE flags. The patch carries the necessary acks from the
relevant maintainers and is routed here as part of prctl()
thread-management."
* tag 'threads-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
prctl: PR_{G,S}ET_IO_FLUSHER to support controlling memory reclaim
sched.h: Annotate sighand_struct with __rcu
test: Add test for pidfd getfd
arch: wire up pidfd_getfd syscall
pid: Implement pidfd_getfd syscall
vfs, fdtable: Add fget_task helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull openat2 support from Al Viro:
"This is the openat2() series from Aleksa Sarai.
I'm afraid that the rest of namei stuff will have to wait - it got
zero review the last time I'd posted #work.namei, and there had been a
leak in the posted series I'd caught only last weekend. I was going to
repost it on Monday, but the window opened and the odds of getting any
review during that... Oh, well.
Anyway, openat2 part should be ready; that _did_ get sane amount of
review and public testing, so here it comes"
From Aleksa's description of the series:
"For a very long time, extending openat(2) with new features has been
incredibly frustrating. This stems from the fact that openat(2) is
possibly the most famous counter-example to the mantra "don't silently
accept garbage from userspace" -- it doesn't check whether unknown
flags are present[1].
This means that (generally) the addition of new flags to openat(2) has
been fraught with backwards-compatibility issues (O_TMPFILE has to be
defined as __O_TMPFILE|O_DIRECTORY|[O_RDWR or O_WRONLY] to ensure old
kernels gave errors, since it's insecure to silently ignore the
flag[2]). All new security-related flags therefore have a tough road
to being added to openat(2).
Furthermore, the need for some sort of control over VFS's path
resolution (to avoid malicious paths resulting in inadvertent
breakouts) has been a very long-standing desire of many userspace
applications.
This patchset is a revival of Al Viro's old AT_NO_JUMPS[3] patchset
(which was a variant of David Drysdale's O_BENEATH patchset[4] which
was a spin-off of the Capsicum project[5]) with a few additions and
changes made based on the previous discussion within [6] as well as
others I felt were useful.
In line with the conclusions of the original discussion of
AT_NO_JUMPS, the flag has been split up into separate flags. However,
instead of being an openat(2) flag it is provided through a new
syscall openat2(2) which provides several other improvements to the
openat(2) interface (see the patch description for more details). The
following new LOOKUP_* flags are added:
LOOKUP_NO_XDEV:
Blocks all mountpoint crossings (upwards, downwards, or through
absolute links). Absolute pathnames alone in openat(2) do not
trigger this. Magic-link traversal which implies a vfsmount jump is
also blocked (though magic-link jumps on the same vfsmount are
permitted).
LOOKUP_NO_MAGICLINKS:
Blocks resolution through /proc/$pid/fd-style links. This is done
by blocking the usage of nd_jump_link() during resolution in a
filesystem. The term "magic-links" is used to match with the only
reference to these links in Documentation/, but I'm happy to change
the name.
It should be noted that this is different to the scope of
~LOOKUP_FOLLOW in that it applies to all path components. However,
you can do openat2(NO_FOLLOW|NO_MAGICLINKS) on a magic-link and it
will *not* fail (assuming that no parent component was a
magic-link), and you will have an fd for the magic-link.
In order to correctly detect magic-links, the introduction of a new
LOOKUP_MAGICLINK_JUMPED state flag was required.
LOOKUP_BENEATH:
Disallows escapes to outside the starting dirfd's
tree, using techniques such as ".." or absolute links. Absolute
paths in openat(2) are also disallowed.
Conceptually this flag is to ensure you "stay below" a certain
point in the filesystem tree -- but this requires some additional
to protect against various races that would allow escape using
"..".
Currently LOOKUP_BENEATH implies LOOKUP_NO_MAGICLINKS, because it
can trivially beam you around the filesystem (breaking the
protection). In future, there might be similar safety checks done
as in LOOKUP_IN_ROOT, but that requires more discussion.
In addition, two new flags are added that expand on the above ideas:
LOOKUP_NO_SYMLINKS:
Does what it says on the tin. No symlink resolution is allowed at
all, including magic-links. Just as with LOOKUP_NO_MAGICLINKS this
can still be used with NOFOLLOW to open an fd for the symlink as
long as no parent path had a symlink component.
LOOKUP_IN_ROOT:
This is an extension of LOOKUP_BENEATH that, rather than blocking
attempts to move past the root, forces all such movements to be
scoped to the starting point. This provides chroot(2)-like
protection but without the cost of a chroot(2) for each filesystem
operation, as well as being safe against race attacks that
chroot(2) is not.
If a race is detected (as with LOOKUP_BENEATH) then an error is
generated, and similar to LOOKUP_BENEATH it is not permitted to
cross magic-links with LOOKUP_IN_ROOT.
The primary need for this is from container runtimes, which
currently need to do symlink scoping in userspace[7] when opening
paths in a potentially malicious container.
There is a long list of CVEs that could have bene mitigated by
having RESOLVE_THIS_ROOT (such as CVE-2017-1002101,
CVE-2017-1002102, CVE-2018-15664, and CVE-2019-5736, just to name a
few).
In order to make all of the above more usable, I'm working on
libpathrs[8] which is a C-friendly library for safe path resolution.
It features a userspace-emulated backend if the kernel doesn't support
openat2(2). Hopefully we can get userspace to switch to using it, and
thus get openat2(2) support for free once it's ready.
Future work would include implementing things like
RESOLVE_NO_AUTOMOUNT and possibly a RESOLVE_NO_REMOTE (to allow
programs to be sure they don't hit DoSes though stale NFS handles)"
* 'work.openat2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Documentation: path-lookup: include new LOOKUP flags
selftests: add openat2(2) selftests
open: introduce openat2(2) syscall
namei: LOOKUP_{IN_ROOT,BENEATH}: permit limited ".." resolution
namei: LOOKUP_IN_ROOT: chroot-like scoped resolution
namei: LOOKUP_BENEATH: O_BENEATH-like scoped resolution
namei: LOOKUP_NO_XDEV: block mountpoint crossing
namei: LOOKUP_NO_MAGICLINKS: block magic-link resolution
namei: LOOKUP_NO_SYMLINKS: block symlink resolution
namei: allow set_root() to produce errors
namei: allow nd_jump_link() to produce errors
nsfs: clean-up ns_get_path() signature to return int
namei: only return -ECHILD from follow_dotdot_rcu()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Depromote debug print on the db8500 platform (Linus Walleij)
- Fix compilation warning when compiling with make W=1 (Amit Kucheria)
- Code cleanup and refactoring, regmap conversion and add hwmon support
on Qoriq (Andrey Smirnov)
- Add an idle injection cpu cooling device and its documentation,
rename the cpu_cooling device to cpufreq_cooling device (Daniel
Lezcano)
- Convert unexported functions to static, add the __init annotation in
the thermal-of code and remove the pointless wrapper functions
(Daniel Lezcano)
- Fix register offset for Armada XP and register reset bit
initialization (Zak Hays)
- Enable hwmon on the rockchip (Stefan Schaeckeler)
- Add the thermal sensor for the H6/H5/H3/A64/A83T/R40 sun8i platform
and their device tree bindings, followed by a fix for the ths number
and the sparse warnings (Yangtao Li)
- Code cleansup for the sun8i and hwmon support (Yangtao Li)
- Silent some messages which are misleading given the changes made in
the previous version on generic-adc (Martin Blumenstingl)
- Rename exynos to Exynos (Krzysztof Kozlowski)
- Add the bcm2711 thermal driver with the device tree bindings (Stefan
Wahren)
- Use usleep_range() instead of udelay() as the call is always done in
a sleep-able context (Geert Uytterhoeven)
- Do code cleanup and re-organization to set the scene for a new
process for the brcmstb (Florian Fainelli)
- Fix bindings check issues on brcm (Stefan Wahren)
- Add Jasper Lake support on int340x (Nivedita Swaminathan)
- Add Comet Lake support on intel pch (Gayatri Kammela)
- Fix unmatched pci_release_region() on x86 (Chuhong Yuan)
- Remove temperature boundaries for rcar and rcar3 (Niklas Söderlund)
- Fix return value to -ENODEV when thermal_zone_of_sensor_register() is
called with the of-node is missing (Peter Mamonov)
- Code cleanup, interrupt bouncing, and better support on stm32 (Pascal
Paillet)
* tag 'thermal-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (66 commits)
thermal: stm32: Fix low threshold interrupt flood
thermal: stm32: Improve temperature computing
thermal: stm32: Handle multiple trip points
thermal: stm32: Disable interrupts at probe
thermal: stm32: Rework sensor mode management
thermal: stm32: Fix icifr register name
thermal: of: Make thermal_zone_of_sensor_register return -ENODEV if a sensor OF node is missing
thermal: rcar_gen3_thermal: Remove temperature bound
thermal: rcar_thermal: Remove temperature bound
thermal: intel: intel_pch_thermal: Add Comet Lake (CML) platform support
thermal: intel: Fix unmatched pci_release_region
thermal: int340x: processor_thermal: Add Jasper Lake support
dt-bindings: brcm,avs-ro-thermal: Fix binding check issues
thermal: brcmstb_thermal: Register different ops per process
thermal: brcmstb_thermal: Restructure interrupt registration
thermal: brcmstb_thermal: Add 16nm process thermal parameters
dt-bindings: thermal: Define BCM7216 thermal sensor compatible
thermal: brcmstb_thermal: Prepare to support a different process
thermal: brcmstb_thermal: Do not use DT coefficients
thermal: rcar_thermal: Use usleep_range() instead of udelay()
...
|
|
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Removed CRYPTO_TFM_RES flags
- Extended spawn grabbing to all algorithm types
- Moved hash descsize verification into API code
Algorithms:
- Fixed recursive pcrypt dead-lock
- Added new 32 and 64-bit generic versions of poly1305
- Added cryptogams implementation of x86/poly1305
Drivers:
- Added support for i.MX8M Mini in caam
- Added support for i.MX8M Nano in caam
- Added support for i.MX8M Plus in caam
- Added support for A33 variant of SS in sun4i-ss
- Added TEE support for Raven Ridge in ccp
- Added in-kernel API to submit TEE commands in ccp
- Added AMD-TEE driver
- Added support for BCM2711 in iproc-rng200
- Added support for AES256-GCM based ciphers for chtls
- Added aead support on SEC2 in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (244 commits)
crypto: arm/chacha - fix build failured when kernel mode NEON is disabled
crypto: caam - add support for i.MX8M Plus
crypto: x86/poly1305 - emit does base conversion itself
crypto: hisilicon - fix spelling mistake "disgest" -> "digest"
crypto: chacha20poly1305 - add back missing test vectors and test chunking
crypto: x86/poly1305 - fix .gitignore typo
tee: fix memory allocation failure checks on drv_data and amdtee
crypto: ccree - erase unneeded inline funcs
crypto: ccree - make cc_pm_put_suspend() void
crypto: ccree - split overloaded usage of irq field
crypto: ccree - fix PM race condition
crypto: ccree - fix FDE descriptor sequence
crypto: ccree - cc_do_send_request() is void func
crypto: ccree - fix pm wrongful error reporting
crypto: ccree - turn errors to debug msgs
crypto: ccree - fix AEAD decrypt auth fail
crypto: ccree - fix typo in comment
crypto: ccree - fix typos in error msgs
crypto: atmel-{aes,sha,tdes} - Retire crypto_platform_data
crypto: x86/sha - Eliminate casts on asm implementations
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"These were the main changes in this cycle:
- More -rt motivated separation of CONFIG_PREEMPT and
CONFIG_PREEMPTION.
- Add more low level scheduling topology sanity checks and warnings
to filter out nonsensical topologies that break scheduling.
- Extend uclamp constraints to influence wakeup CPU placement
- Make the RT scheduler more aware of asymmetric topologies and CPU
capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y
- Make idle CPU selection more consistent
- Various fixes, smaller cleanups, updates and enhancements - please
see the git log for details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
sched/fair: Define sched_idle_cpu() only for SMP configurations
sched/topology: Assert non-NUMA topology masks don't (partially) overlap
idle: fix spelling mistake "iterrupts" -> "interrupts"
sched/fair: Remove redundant call to cpufreq_update_util()
sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled
sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP
sched/fair: calculate delta runnable load only when it's needed
sched/cputime: move rq parameter in irqtime_account_process_tick
stop_machine: Make stop_cpus() static
sched/debug: Reset watchdog on all CPUs while processing sysrq-t
sched/core: Fix size of rq::uclamp initialization
sched/uclamp: Fix a bug in propagating uclamp value in new cgroups
sched/fair: Load balance aggressively for SCHED_IDLE CPUs
sched/fair : Improve update_sd_pick_busiest for spare capacity case
watchdog: Remove soft_lockup_hrtimer_cnt and related code
sched/rt: Make RT capacity-aware
sched/fair: Make EAS wakeup placement consider uclamp restrictions
sched/fair: Make task_fits_capacity() consider uclamp restrictions
sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with()
sched/uclamp: Make uclamp util helpers use and return UL values
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Ftrace is one of the last W^X violators (after this only KLP is
left). These patches move it over to the generic text_poke()
interface and thereby get rid of this oddity. This requires a
surprising amount of surgery, by Peter Zijlstra.
- x86/AMD PMUs: add support for 'Large Increment per Cycle Events' to
count certain types of events that have a special, quirky hw ABI
(by Kim Phillips)
- kprobes fixes by Masami Hiramatsu
Lots of tooling updates as well, the following subcommands were
updated: annotate/report/top, c2c, clang, record, report/top TUI,
sched timehist, tests; plus updates were done to the gtk ui, libperf,
headers and the parser"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
perf/x86/amd: Add support for Large Increment per Cycle Events
perf/x86/amd: Constrain Large Increment per Cycle events
perf/x86/intel/rapl: Add Comet Lake support
tracing: Initialize ret in syscall_enter_define_fields()
perf header: Use last modification time for timestamp
perf c2c: Fix return type for histogram sorting comparision functions
perf beauty sockaddr: Fix augmented syscall format warning
perf/ui/gtk: Fix gtk2 build
perf ui gtk: Add missing zalloc object
perf tools: Use %define api.pure full instead of %pure-parser
libperf: Setup initial evlist::all_cpus value
perf report: Fix no libunwind compiled warning break s390 issue
perf tools: Support --prefix/--prefix-strip
perf report: Clarify in help that --children is default
tools build: Fix test-clang.cpp with Clang 8+
perf clang: Fix build with Clang 9
kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic
tools lib: Fix builds when glibc contains strlcpy()
perf report/top: Make 'e' visible in the help and make it toggle showing callchains
perf report/top: Do not offer annotation for symbols without samples
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Cleanup of the GOP [graphics output] handling code in the EFI stub
- Complete refactoring of the mixed mode handling in the x86 EFI stub
- Overhaul of the x86 EFI boot/runtime code
- Increase robustness for mixed mode code
- Add the ability to disable DMA at the root port level in the EFI
stub
- Get rid of RWX mappings in the EFI memory map and page tables,
where possible
- Move the support code for the old EFI memory mapping style into its
only user, the SGI UV1+ support code.
- plus misc fixes, updates, smaller cleanups.
... and due to interactions with the RWX changes, another round of PAT
cleanups make a guest appearance via the EFI tree - with no side
effects intended"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
efi/x86: Disable instrumentation in the EFI runtime handling code
efi/libstub/x86: Fix EFI server boot failure
efi/x86: Disallow efi=old_map in mixed mode
x86/boot/compressed: Relax sed symbol type regex for LLVM ld.lld
efi/x86: avoid KASAN false positives when accessing the 1: 1 mapping
efi: Fix handling of multiple efi_fake_mem= entries
efi: Fix efi_memmap_alloc() leaks
efi: Add tracking for dynamically allocated memmaps
efi: Add a flags parameter to efi_memory_map
efi: Fix comment for efi_mem_type() wrt absent physical addresses
efi/arm: Defer probe of PCIe backed efifb on DT systems
efi/x86: Limit EFI old memory map to SGI UV machines
efi/x86: Avoid RWX mappings for all of DRAM
efi/x86: Don't map the entire kernel text RW for mixed mode
x86/mm: Fix NX bit clearing issue in kernel_map_pages_in_pgd
efi/libstub/x86: Fix unused-variable warning
efi/libstub/x86: Use mandatory 16-byte stack alignment in mixed mode
efi/libstub/x86: Use const attribute for efi_is_64bit()
efi: Allow disabling PCI busmastering on bridges during boot
efi/x86: Allow translating 64-bit arguments for mixed mode calls
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
"The main changes are to move the ORC unwind table sorting from early
init to build-time - this speeds up booting.
No change in functionality intended"
* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Fix !CONFIG_MODULES build warning
x86/unwind/orc: Remove boot-time ORC unwind tables sorting
scripts/sorttable: Implement build-time ORC unwind table sorting
scripts/sorttable: Rename 'sortextable' to 'sorttable'
scripts/sortextable: Refactor the do_func() function
scripts/sortextable: Remove dead code
scripts/sortextable: Clean up the code to meet the kernel coding style better
scripts/sortextable: Rewrite error/success handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement provides:
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated
CPUs the interrupt could be routed to an isolated CPU which would
then be disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is
online in the assigned affinity mask the interrupt is routed to a
housekeeping CPU.
If there is no online housekeeping CPU in the affinity mask, then
the interrupt is routed to an isolated CPU to keep the device queue
intact, but unless the isolated CPU submits I/O by itself these
interrupts are not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI,
NXP INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code"
* tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
genirq, sched/isolation: Isolate from handling managed interrupts
irqchip/gic-v4.1: Allow direct invalidation of VLPIs
irqchip/gic-v4.1: Suppress per-VLPI doorbell
irqchip/gic-v4.1: Add VPE INVALL callback
irqchip/gic-v4.1: Add VPE eviction callback
irqchip/gic-v4.1: Add VPE residency callback
irqchip/gic-v4.1: Add mask/unmask doorbell callbacks
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
irqdomain: Fix a memory leak in irq_domain_push_irq()
irqchip: Add NXP INTMUX interrupt multiplexer support
dt-bindings: interrupt-controller: Add binding for NXP INTMUX interrupt multiplexer
irqchip: Define EXYNOS_IRQ_COMBINER
irqchip/meson-gpio: Add support for meson a1 SoCs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timekeeping and timers departement provides:
- Time namespace support:
If a container migrates from one host to another then it expects
that clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime
these clocks can differ significantly on two hosts, in the worst
case time goes backwards which is a violation of the POSIX
requirements.
The time namespace addresses this problem. It allows to set offsets
for clock MONOTONIC and BOOTTIME once after creation and before
tasks are associated with the namespace. These offsets are taken
into account by timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided
by this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric
potential use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (ie where host time
offsets = 0) is in the noise and great effort was made to ensure
that especially in the VDSO. If time namespace is disabled in the
kernel configuration the code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this
feature and kept on for more than a year addressing review
comments, finding better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure
that the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code"
* tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
alarmtimer: Make alarmtimer_get_rtcdev() a stub when CONFIG_RTC_CLASS=n
alarmtimer: Use wakeup source from alarmtimer platform device
alarmtimer: Make alarmtimer platform device child of RTC device
alarmtimer: Update alarmtimer_get_rtcdev() docs to reflect reality
hrtimer: Add missing sparse annotation for __run_timer()
lib/vdso: Only read hrtimer_res when needed in __cvdso_clock_getres()
MIPS: vdso: Define BUILD_VDSO32 when building a 32bit kernel
clocksource/drivers/hyper-v: Set TSC clocksource as default w/ InvariantTSC
clocksource/drivers/hyper-v: Untangle stimers and timesync from clocksources
clocksource/drivers/timer-microchip-pit64b: Fix sparse warning
clocksource/drivers/exynos_mct: Rename Exynos to lowercase
clocksource/drivers/timer-ti-dm: Fix uninitialized pointer access
clocksource/drivers/timer-ti-dm: Switch to platform_get_irq
clocksource/drivers/timer-ti-dm: Convert to devm_platform_ioremap_resource
clocksource/drivers/em_sti: Fix variable declaration in em_sti_probe
clocksource/drivers/em_sti: Convert to devm_platform_ioremap_resource
clocksource/drivers/bcm2835_timer: Fix memory leak of timer
clocksource/drivers/cadence-ttc: Use ttc driver as platform driver
clocksource/drivers/timer-microchip-pit64b: Add Microchip PIT64B support
clocksource/drivers/hyper-v: Reserve PAGE_SIZE space for tsc page
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two fixes for the generic VDSO code which missed 5.5:
- Make the update to the coarse timekeeper unconditional.
This is required because the coarse timekeeper interfaces in the
VDSO do not depend on a VDSO capable clocksource. If the system
does not have a VDSO capable clocksource and the update is
depending on the VDSO capable clocksource, the coarse VDSO
interfaces would operate on stale data forever.
- Invert the logic of __arch_update_vdso_data() to avoid further head
scratching.
Tripped over this several times while analyzing the update problem
above"
* tag 'timers-urgent-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lib/vdso: Update coarse timekeeper unconditionally
lib/vdso: Make __arch_update_vdso_data() logic understandable
|
|
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
|
|
For ring-based dirty log tracking, it will be more efficient to account
writes during schedule-out or schedule-in to the currently running VCPU.
We would like to do it even if the write doesn't use the current VCPU's
address space, as is the case for cached writes (see commit 4e335d9e7ddb,
"Revert "KVM: Support vCPU-based gfn->hva cache"", 2017-05-02).
Therefore, add a mechanism to track the currently-loaded kvm_vcpu struct.
There is already something similar in KVM/ARM; one important difference
is that kvm_arch_vcpu_{load,put} have two callers in virt/kvm/kvm_main.c:
we have to update both the architecture-independent vcpu_{load,put} and
the preempt notifiers.
Another change made in the process is to allow using kvm_get_running_vcpu()
in preemptible code. This is allowed because preempt notifiers ensure
that the value does not change even after the VCPU thread is migrated.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove kvm_arch_vcpu_init() and kvm_arch_vcpu_uninit() now that all
arch specific implementations are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add an arm specific hook to free the arm64-only sve_state. Doing so
eliminates the last functional code from kvm_arch_vcpu_uninit() across
all architectures and paves the way for removing kvm_arch_vcpu_init()
and kvm_arch_vcpu_uninit() entirely.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.6 include migrating DM365 SoC to use
drivers/clocksource based driver for timer. This leads to removal
of machine specific timer driver.
There are two patches adding missing fixed regulators for audio codecs
on DM365 and DM644x EVMs.
* tag 'davinci-for-v5.6/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm644x-evm: Add Fixed regulators needed for tlv320aic33
ARM: davinci: dm365-evm: Add Fixed regulators needed for tlv320aic3101
ARM: davinci: remove legacy timer support
ARM: davinci: dm365: switch to using the clocksource driver
clocksource: davinci: only enable clockevents once tim34 is initialized
Link: https://lore.kernel.org/r/043eb5b2-a302-4de6-a3e8-8238e49483b1@ti.com/
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This builds the BCM2711 thermal driver as module for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-5-git-send-email-stefan.wahren@i2se.com
|
|
This enables thermal for the BCM2711 (used on Raspberry Pi 4) by adding
the AVS monitor and a subnode for the thermal part.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1578941778-23321-4-git-send-email-stefan.wahren@i2se.com
|
|
Minor conflict in mlx5 because changes happened to code that has
moved meanwhile.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM fixes from Russell King:
- fix ftrace relocation type filtering
- relax arch timer version check
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8955/1: virt: Relax arch timer version check during early boot
ARM: 8950/1: ftrace/recordmcount: filter relocation types
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Late omap dts changes for v5.6 merge window
This series of changes mostly configures the cameras for dra7 and
am437x that have been pending for few months now because of waiting
for clock dependencies to clear. So these changes are based on earlier
dts changes with with Tero Kristo's for-5.6-ti-clk branch merged in.
Then there's a series of changes to configure powervr sgx target module
for am335x, am437x and dra7 that have been waiting to have the rstctrl
reset driver dependencies to clear.
Also included are few minor patches to configure 1-wire and coulomb
counter calibration interrupt for droid4.
* tag 'omap-for-v5.6/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: dts: Add omap3-echo
ARM: dts: Add dtsi files for AM3703, AM3715 and DM3725
ARM: dts: am335x-icev2: Add support for OSD9616P0899-10 at i2c0
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Late changes for omap secure accelerators for v5.6 merge window
A series of changes to configure secure accelerators for omap4 & 5
to finally get hardware random number generator working.
Apologies on a late pull request on these changes, but this pull
request could not be sent out earlier because of a dependency to
recent clock changes. This is based on earlier changes to drop omap
legacy platform data with Tero Kristo's for-5.6-ti-clk branch merged
in.
* tag 'omap-for-v5.6/ti-sysc-drop-pdata-crypto-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (98 commits)
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
ARM: dts: Configure interconnect target module for omap4 des
ARM: dts: Configure interconnect target module for omap4 aes
ARM: dts: Configure interconnect target module for omap4 sham
ARM: dts: Configure omap5 rng to probe with ti-sysc
ARM: dts: Configure omap4 rng to probe with ti-sysc
ARM: dts: Add missing omap5 secure clocks
ARM: dts: Add missing omap4 secure clocks
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
dmaengine: ti: omap-dma: don't allow a null od->plat pointer to be dereferenced
ARM: OMAP2+: Drop legacy platform data for sdma
ARM: OMAP2+: Drop legacy init for sdma
...
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Randconfig build fix for recent SoC changes for v5.6
We can get build failures if let's say if only am335x SoC is selected.
Let's fix this by always building secure-common.
* tag 'omap-for-v5.6/soc-build-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix undefined reference to omap_secure_init
Link: https://lore.kernel.org/r/pull-1579896427-50330@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Stubs for swapops are not required after 9b98fa229485 (mm: stub out
all of swapops.h for !CONFIG_MMU)
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
To perform the reserve_crashkernel() operation kexec uses SECTION_SIZE to
find a memblock in a range.
SECTION_SIZE is not defined for nommu systems. Trying to compile kexec in
these conditions results in a build error:
linux/arch/arm/kernel/setup.c: In function ‘reserve_crashkernel’:
linux/arch/arm/kernel/setup.c:1016:25: error: ‘SECTION_SIZE’ undeclared
(first use in this function); did you mean ‘SECTIONS_WIDTH’?
crash_size, SECTION_SIZE);
^~~~~~~~~~~~
SECTIONS_WIDTH
linux/arch/arm/kernel/setup.c:1016:25: note: each undeclared identifier
is reported only once for each function it appears in
linux/scripts/Makefile.build:265: recipe for target 'arch/arm/kernel/setup.o'
failed
Make KEXEC depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
As of commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly"), free_memmap() might not always be inlined, and thus is
triggering a section warning:
WARNING: vmlinux.o(.text.unlikely+0x904): Section mismatch in reference from the function free_memmap() to the function .meminit.text:memblock_free()
Mark it as __init, since the faller (free_unused_memmap) already is.
Fixes: ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
