summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)AuthorFilesLines
2022-07-04ARM: dts: stm32: use the correct clock source for CEC on stm32mp151Gabriel Fernandez1-1/+1
The peripheral clock of CEC is not LSE but CEC. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-07-04ARM: dts: stm32: fix pwr regulators references to use scmiEtienne Carriere3-0/+54
Fixes stm32mp15*-scmi DTS files introduced in [1] to also access PWR regulators through SCMI service. This is needed since enabling secure only access to RCC clock and reset controllers also enables secure access only on PWR voltage regulators reg11, reg18 and usb33 hence these must also be accessed through SCMI Voltage Domain protocol. This change applies on commit [2] that already corrects issues from commit [1]. Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Link: [1] https://lore.kernel.org/linux-arm-kernel/20220422150952.20587-7-alexandre.torgue@foss.st.com Link: [2] https://lore.kernel.org/linux-arm-kernel/20220613071920.5463-1-alexandre.torgue@foss.st.com Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-06-26Merge tag 'soc-fixes-5.19' of ↵Linus Torvalds16-100/+70
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "A number of fixes have accumulated, but they are largely for harmless issues: - Several OF node leak fixes - A fix to the Exynos7885 UART clock description - DTS fixes to prevent boot failures on TI AM64 and J721s2 - Bus probe error handling fixes for Baikal-T1 - A fixup to the way STM32 SoCs use separate dts files for different firmware stacks - Multiple code fixes for Arm SCMI firmware, all dealing with robustness of the implementation - Multiple NXP i.MX devicetree fixes, addressing incorrect data in DT nodes - Three updates to the MAINTAINERS file, including Florian Fainelli taking over BCM283x/BCM2711 (Raspberry Pi) from Nicolas Saenz Julienne" * tag 'soc-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits) ARM: dts: aspeed: nuvia: rename vendor nuvia to qcom arm: mach-spear: Add missing of_node_put() in time.c ARM: cns3xxx: Fix refcount leak in cns3xxx_init MAINTAINERS: Update email address arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode arm64: dts: ti: k3-j721s2: Fix overlapping GICD memory region ARM: dts: bcm2711-rpi-400: Fix GPIO line names bus: bt1-axi: Don't print error on -EPROBE_DEFER bus: bt1-apb: Don't print error on -EPROBE_DEFER ARM: Fix refcount leak in axxia_boot_secondary ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15 soc: imx: imx8m-blk-ctrl: fix display clock for LCDIF2 power domain ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarity ARM: dts: imx6qdl: correct PU regulator ramp delay firmware: arm_scmi: Fix incorrect error propagation in scmi_voltage_descriptors_get firmware: arm_scmi: Avoid using extended string-buffers sizes if not necessary firmware: arm_scmi: Fix SENSOR_AXIS_NAME_GET behaviour when unsupported ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe MAINTAINERS: Update BCM2711/BCM2835 maintainer ...
2022-06-24ARM: dts: aspeed: nuvia: rename vendor nuvia to qcomJae Hyun Yoo2-3/+3
Nuvia has been acquired by Qualcomm and the vendor name 'nuvia' will not be used anymore so rename aspeed-bmc-nuvia-dc-scm.dts to aspeed-bmc-qcom-dc-scm-v1.dts and change 'nuvia' to 'qcom' as its vendor name in the file. Fixes: 7b46aa7c008d ("ARM: dts: aspeed: Add Nuvia DC-SCM BMC") Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20220523175640.60155-1-quic_jaehyoo@quicinc.com Link: https://lore.kernel.org/r/20220624070511.4070659-1-joel@jms.id.au' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-24Merge tag 'samsung-fixes-5.19' of ↵Arnd Bergmann1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/fixes Samsung fixes for v5.19 Both fixes are for issues present before v5.19 merge window: 1. Correct UART clocks on Exynos7885. Although the initial, fixed DTS commit is from v5.18, the issue will be exposed with a upcoming fix to Exynos7885 clock driver, so we need to correct the DTS earlier. 2. Fix theoretical OF node leak in Exynos machine code. * tag 'samsung-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: exynos: Fix refcount leak in exynos_map_pmu arm64: dts: exynos: Correct UART clocks on Exynos7885 Link: https://lore.kernel.org/r/20220624080423.31427-1-krzysztof.kozlowski@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-24Merge tag 'arm-soc/for-5.19/devicetree-fixes' of ↵Arnd Bergmann1-3/+3
https://github.com/Broadcom/stblinux into arm/fixes This pull request contains Broadcom ARM-SoC Device Tree fixes for 5.19, please pull the following: - Stefan fixes the Raspberry Pi 400 GPIO expander line names to match that of the downstream Raspberry Pi Linux tree * tag 'arm-soc/for-5.19/devicetree-fixes' of https://github.com/Broadcom/stblinux: ARM: dts: bcm2711-rpi-400: Fix GPIO line names Link: https://lore.kernel.org/r/20220620170745.2485199-1-f.fainelli@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-24arm: mach-spear: Add missing of_node_put() in time.cLiang He1-2/+6
In spear_setup_of_timer(), of_find_matching_node() will return a node pointer with refcount incrementd. We should use of_node_put() in each fail path or when it is not used anymore. Signed-off-by: Liang He <windhl@126.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Link: https://lore.kernel.org/r/20220616093027.3984903-1-windhl@126.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-24ARM: cns3xxx: Fix refcount leak in cns3xxx_initMiaoqian Lin1-0/+2
of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak. Fixes: 415f59142d9d ("ARM: cns3xxx: initial DT support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Acked-by: Krzysztof Halasa <khalasa@piap.pl> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-17ARM: dts: bcm2711-rpi-400: Fix GPIO line namesStefan Wahren1-3/+3
The GPIO expander line names has been fixed in the vendor tree last year, so upstream these changes. Fixes: 1c701accecf2 ("ARM: dts: Add Raspberry Pi 400 support") Reported-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2022-06-14ARM: dts: at91: ksz9477_evb: fix port/phy validationOleksij Rempel1-0/+5
Latest drivers version requires phy-mode to be set. Otherwise we will use "NA" mode and the switch driver will invalidate this port mode. Fixes: 65ac79e18120 ("net: dsa: microchip: add the phylink get_caps") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20220610081621.584393-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-14ARM: Fix refcount leak in axxia_boot_secondaryMiaoqian Lin1-0/+1
of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak. Fixes: 1d22924e1c4e ("ARM: Add platform support for LSI AXM55xx SoC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220601090548.47616-1-linmq006@gmail.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-14ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15Alexandre Torgue6-89/+51
Adding a "secure" version of STM32 boards (DK1/DK2/ED1/EV1), SCMI (clock/ reset) protocol and OP-TEE node have been added in SoC dtsi file (stm32mp151.dtsi). They have been added with a status disabled in order to keep our legacy unchanged. It is actually not enough to keep our legacy unchanged. First, just a reminder about our use case: TF-A (BL2) loads and starts OP-TEE, then loads and runs U-Boot. U-Boot code checks if an OP-TEE is running, if yes it searches in Kernel device tree if an OP-TEE node is present: -If the OP-TEE node is not present then U-Boot copies OP-TEE node and its reserved memory region from U-Boot device tree to the kernel device tree. -If the OP-TEE node is present then it does nothing (this OP-TEE node will be used by Linux). So U-Boot lets the kernel device tree unchanged thinking it is correct for an OP-TEE usage. It is the case for our legacy boards, the OP-TEE node is present (although disabled) but the reserved memory region is not declared. As no memory region has been reserved for OP-TEE, the end of DDR is seen by the kernel as free and then used for CMA. But as OP-TEE is running, this end of DDR is already used by OP-TEE. So as soon as kernel tries to access to the CMA region OP-TEE raises an error. To fix it, all OP-TEE node and SCMI is moved in a dedicated file. Fixes: 40b4157dbd8c ("ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15") Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Link: https://lore.kernel.org/r/20220613071920.5463-1-alexandre.torgue@foss.st.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-14Merge tag 'imx-fixes-5.19' of ↵Arnd Bergmann3-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.19: - Correct i.MX7 power domain for HSIC USB PHY node to fix an USB Host issue, that is all downstream events will be lost if USB host is runtime suspended. - Fix i.MX8M blk-ctrl LCDIF2 power domain to point to refer to the correct clock. - Correct i.MX6Q/DL PU regulator ramp delay to fix some peripherals power-up failure especially when the chip is at a low temperature. - Fix capacitive touch reset polarity for imx6qdl-colibri board. * tag 'imx-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: soc: imx: imx8m-blk-ctrl: fix display clock for LCDIF2 power domain ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarity ARM: dts: imx6qdl: correct PU regulator ramp delay ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node Link: https://lore.kernel.org/r/20220614095515.GU254723@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-14ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarityMax Krummenacher1-1/+1
The commit feedaacdadfc ("Input: atmel_mxt_ts - fix up inverted RESET handler") requires the reset GPIO to have GPIO_ACTIVE_LOW. Fixes: 1524b27c94a6 ("ARM: dts: imx6dl-colibri: Move common nodes to SoM dtsi") Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-06-14ARM: dts: imx6qdl: correct PU regulator ramp delayLucas Stach1-1/+1
Contrary to what was believed at the time, the ramp delay of 150us is not plenty for the PU LDO with the default step time of 512 pulses of the 24MHz clock. Measurements have shown that after enabling the LDO the voltage on VDDPU_CAP jumps to ~750mV in the first step and after that the regulator executes the normal ramp up as defined by the step size control. This means it takes the regulator between 360us and 370us to ramp up to the nominal 1.15V voltage for this power domain. With the old setting of the ramp delay the power up of the PU GPC domain would happen in the middle of the regulator ramp with the voltage being at around 900mV. Apparently this was enough for most units to properly power up the peripherals in the domain and execute the reset. Some units however, fail to power up properly, especially when the chip is at a low temperature. In that case any access to the GPU registers would yield an incorrect result with no way to recover from this situation. Change the ramp delay to 380us to cover the measured ramp up time with a bit of additional slack. Fixes: 40130d327f72 ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-06-10ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY nodeAlexander Stein1-1/+1
Move the power domain to its actual user. This keeps the power domain enabled even when the USB host is runtime suspended. This is necessary to detect any downstream events, like device attach. Fixes: 02f8eb40ef7b ("ARM: dts: imx7s: Add power domain for imx7d HSIC") Suggested-by: Jun Li <jun.li@nxp.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-06-06xen/virtio: Enable restricted memory access using Xen grant mappingsJuergen Gross1-0/+2
In order to support virtio in Xen guests add a config option XEN_VIRTIO enabling the user to specify whether in all Xen guests virtio should be able to access memory via Xen grant mappings only on the host side. Also set PLATFORM_VIRTIO_RESTRICTED_MEM_ACCESS feature from the guest initialization code on Arm and x86 if CONFIG_XEN_VIRTIO is enabled. Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/1654197833-25362-5-git-send-email-olekstysh@gmail.com Signed-off-by: Juergen Gross <jgross@suse.com>
2022-06-06ARM: exynos: Fix refcount leak in exynos_map_pmuMiaoqian Lin1-0/+1
of_find_matching_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak. of_node_put() checks null pointer. Fixes: fce9e5bb2526 ("ARM: EXYNOS: Add support for mapping PMU base address via DT") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523145513.12341-1-linmq006@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2022-06-06arm/xen: Introduce xen_setup_dma_ops()Oleksandr Tyshchenko2-5/+4
This patch introduces new helper and places it in new header. The helper's purpose is to assign any Xen specific DMA ops in a single place. For now, we deal with xen-swiotlb DMA ops only. The one of the subsequent commits in current series will add xen-grant DMA ops case. Also re-use the xen_swiotlb_detect() check on Arm32. Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> [For arm64] Acked-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/1654197833-25362-2-git-send-email-olekstysh@gmail.com Signed-off-by: Juergen Gross <jgross@suse.com>
2022-06-03Merge tag 'kthread-cleanups-for-v5.19' of ↵Linus Torvalds1-5/+7
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace Pull kthread updates from Eric Biederman: "This updates init and user mode helper tasks to be ordinary user mode tasks. Commit 40966e316f86 ("kthread: Ensure struct kthread is present for all kthreads") caused init and the user mode helper threads that call kernel_execve to have struct kthread allocated for them. This struct kthread going away during execve in turned made a use after free of struct kthread possible. Here, commit 343f4c49f243 ("kthread: Don't allocate kthread_struct for init and umh") is enough to fix the use after free and is simple enough to be backportable. The rest of the changes pass struct kernel_clone_args to clean things up and cause the code to make sense. In making init and the user mode helpers tasks purely user mode tasks I ran into two complications. The function task_tick_numa was detecting tasks without an mm by testing for the presence of PF_KTHREAD. The initramfs code in populate_initrd_image was using flush_delayed_fput to ensuere the closing of all it's file descriptors was complete, and flush_delayed_fput does not work in a userspace thread. I have looked and looked and more complications and in my code review I have not found any, and neither has anyone else with the code sitting in linux-next" * tag 'kthread-cleanups-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: sched: Update task_tick_numa to ignore tasks without an mm fork: Stop allowing kthreads to call execve fork: Explicitly set PF_KTHREAD init: Deal with the init process being a user mode process fork: Generalize PF_IO_WORKER handling fork: Explicity test for idle tasks in copy_thread fork: Pass struct kernel_clone_args into copy_thread kthread: Don't allocate kthread_struct for init and umh
2022-06-03ARM: omap1: enable multiplatformArnd Bergmann7-133/+21
With all the header files out of the way, and the clock driver converted to the common framework, nothing stops us from building OMAP together with the other platforms. As usual, the decompressor support is a victim here, and is only available when CONFIG_DEBUG_LL is configured for the particular board. Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-03ARM: OMAP1: clock: Convert to CCFJanusz Krzysztofik5-764/+563
OMAP1 still uses its own implementation of standard clock API defined in include/linux/clk.h. Internals of that implementation are not visible outside OMAP1 directory. As a consequence, device drivers are not able to register clocks potentially provided by peripheral devices. Drop OMAP1 implementation of the clock API and enable common clock framework. Modify the remaining low level code to be compatible with clock provider API and register the clocks with CCF. Move initialisation of clocks to omap1_timer_init() to avoid memory allocation issues at early setup phase from where omap1_init_early() is called. Register the clocks after initialization of clock I/O registers, local clock pointers used by OMAP1 clock ops, and local .rate fields of clocks with no local implementation of .recalc ops, so CCF structures are populated with correct data during clock registration. Instead of enabling some of the registered clocks, flag them for CCF as critical. Introduce .is_enabled op using code that verifies hardware status of clock enablement, split out from implementation of .disable_unused op, so the latter is actually called by CCF for not requested but hardware enabled clocks. Add .round_rate ops where missing so .set_rate ops are called by CCF as expected. Since CCF allows parallel execution of .enable/.disable and .set_rate ops, protect registers shared among those groups of ops from concurrent access with spinlocks. Drop local debugfs support in favor of that provided by CCF. v2: flag tc2_ck as CLK_IS_CRITICAL (Aaro) v3: rebase on top of soc/omap1-multiplatform-5.18, - drop no longer needed includes from arch/arm/mach-omap1/io.c Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-06-03Merge tag 'usb-5.19-rc1' of ↵Linus Torvalds2-5/+8
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt updates from Greg KH: "Here is the "big" set of USB and Thunderbolt driver changes for 5.18-rc1. For the most part it's been a quiet development cycle for the USB core, but there are the usual "hot spots" of development activity. Included in here are: - Thunderbolt driver updates: - fixes for devices without displayport adapters - lane bonding support and improvements - other minor changes based on device testing - dwc3 gadget driver changes. It seems this driver will never be finished given that the IP core is showing up in zillions of new devices and each implementation decides to do something different with it... - uvc gadget driver updates as more devices start to use and rely on this hardware as well - usb_maxpacket() api changes to remove an unneeded and unused parameter. - usb-serial driver device id updates and small cleanups - typec cleanups and fixes based on device testing - device tree updates for usb properties - lots of other small fixes and driver updates. All of these have been in linux-next for weeks with no reported problems" * tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits) USB: new quirk for Dell Gen 2 devices usb: dwc3: core: Add error log when core soft reset failed usb: dwc3: gadget: Move null pinter check to proper place usb: hub: Simplify error and success path in port_over_current_notify usb: cdns3: allocate TX FIFO size according to composite EP number usb: dwc3: Fix ep0 handling when getting reset while doing control transfer usb: Probe EHCI, OHCI controllers asynchronously usb: isp1760: Fix out-of-bounds array access xhci: Don't defer primary roothub registration if there is only one roothub USB: serial: option: add Quectel BG95 modem USB: serial: pl2303: fix type detection for odd device xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI xhci: Remove quirk for over 10 year old evaluation hardware xhci: prevent U2 link power state if Intel tier policy prevented U1 xhci: use generic command timer for stop endpoint commands. usb: host: xhci-plat: omit shared hcd if either root hub has no ports usb: host: xhci-plat: prepare operation w/o shared hcd usb: host: xhci-plat: create shared hcd after having added main hcd xhci: prepare for operation w/o shared hcd xhci: factor out parts of xhci_gen_setup() ...
2022-06-02Merge tag 'arm-late-5.19' of ↵Linus Torvalds41-92/+755
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull more ARM SoC updates from Arnd Bergmann: "This is the second part of the general SoC updates, containing everything that did not make it in the initial pull request, or that came in as a bugfix later. - Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip, including a new machine using an ASPEED BMC. - More DT fixes from Krzysztof Kozlowski across platforms - A new SoC platform for the GXP baseboard management controller, used in current server products from HPE" * tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (56 commits) ARM: configs: Enable more audio support for i.MX tee: optee: Pass a pointer to virt_addr_valid() arm64: dts: rockchip: rename Quartz64-A bluetooth gpios arm64: dts: rockchip: add clocks property to cru node rk3368 arm64: dts: rockchip: add clocks property to cru node rk3308 arm64: dts: rockchip: add clocks to rk356x cru ARM: dts: rockchip: add clocks property to cru node rk3228 ARM: dts: rockchip: add clocks property to cru node rk3036 ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188 ARM: dts: rockchip: add clocks property to cru node rk3288 ARM: dts: rockchip: Remove "amba" bus nodes from rv1108 ARM: dts: rockchip: add clocks property to cru node rv1108 arm64: dts: sprd: use new 'dma-channels' property ARM: dts: da850: use new 'dma-channels' property ARM: dts: pxa: use new 'dma-channels/requests' properties soc: ixp4xx/qmgr: Fix unused match warning ARM: ep93xx: Make ts72xx_register_flash() static ARM: configs: enable support for Kontron KSwitch D10 ep93xx: clock: Do not return the address of the freed memory arm64: dts: intel: add device tree for n6000 ...
2022-06-02Merge tag 'arm-multiplatform-5.19-2' of ↵Linus Torvalds179-2555/+2226
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull more ARM multiplatform updates from Arnd Bergmann: "The second part of the multiplatform changes now converts the Intel/Marvell PXA platform along with the rest. The patches went through several rebases before the merge window as bugs were found, so they remained separate. This has to touch a lot of drivers, in particular the touchscreen, pcmcia, sound and clk bits, to detach the driver files from the platform and board specific header files" * tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits) ARM: pxa/mmp: remove traces of plat-pxa ARM: pxa: convert to multiplatform ARM: pxa/sa1100: move I/O space to PCI_IOBASE ARM: pxa: remove support for MTD_XIP ARM: pxa: move mach/*.h to mach-pxa/ ARM: PXA: fix multi-cpu build of xsc3 ARM: pxa: move plat-pxa to drivers/soc/ ARM: mmp: rename pxa_register_device ARM: mmp: remove tavorevb board support ARM: pxa: remove unused mach/bitfield.h ARM: pxa: move clk register definitions to driver ARM: pxa: move smemc register access from clk to platform cpufreq: pxa3: move clk register access to clk driver ARM: pxa: remove get_clk_frequency_khz() ARM: pxa: pcmcia: move smemc configuration back to arch ASoC: pxa: i2s: use normal MMIO accessors ASoC: pxa: ac97: use normal MMIO accessors ASoC: pxa: use pdev resource for FIFO regs Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops Input: wm97xx - switch to using threaded IRQ ...
2022-05-31ARM: pxa/mmp: remove traces of plat-pxaArnd Bergmann1-2/+0
The missing include directory caused a W=1 warning that can be trivially fixed. I also noticed references in the marvell.rst documentation that can be removed at the same time. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-30Merge tag 'pm-5.19-rc1-2' of ↵Linus Torvalds1-3/+1
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management updates from Rafael Wysocki: "These update the ARM cpufreq drivers and fix up the CPPC cpufreq driver after recent changes, update the OPP code and PM documentation and add power sequences support to the system reboot and power off code. Specifics: - Add Tegra234 cpufreq support (Sumit Gupta) - Clean up and enhance the Mediatek cpufreq driver (Wan Jiabing, Rex-BC Chen, and Jia-Wei Chang) - Fix up the CPPC cpufreq driver after recent changes (Zheng Bin, Pierre Gondois) - Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine Oudjana) - Use list iterator only inside the list_for_each_entry loop (Xiaomeng Tong, and Jakob Koschel) - New APIs related to finding OPP based on interconnect bandwidth (Krzysztof Kozlowski) - Fix the missing of_node_put() in _bandwidth_supported() (Dan Carpenter) - Cleanups (Krzysztof Kozlowski, and Viresh Kumar) - Add Out of Band mode description to the intel-speed-select utility documentation (Srinivas Pandruvada) - Add power sequences support to the system reboot and power off code and make related platform-specific changes for multiple platforms (Dmitry Osipenko, Geert Uytterhoeven)" * tag 'pm-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (60 commits) cpufreq: CPPC: Fix unused-function warning cpufreq: CPPC: Fix build error without CONFIG_ACPI_CPPC_CPUFREQ_FIE Documentation: admin-guide: PM: Add Out of Band mode kernel/reboot: Change registration order of legacy power-off handler m68k: virt: Switch to new sys-off handler API kernel/reboot: Add devm_register_restart_handler() kernel/reboot: Add devm_register_power_off_handler() soc/tegra: pmc: Use sys-off handler API to power off Nexus 7 properly reboot: Remove pm_power_off_prepare() regulator: pfuze100: Use devm_register_sys_off_handler() ACPI: power: Switch to sys-off handler API memory: emif: Use kernel_can_power_off() mips: Use do_kernel_power_off() ia64: Use do_kernel_power_off() x86: Use do_kernel_power_off() sh: Use do_kernel_power_off() m68k: Switch to new sys-off handler API powerpc: Use do_kernel_power_off() xen/x86: Use do_kernel_power_off() parisc: Use do_kernel_power_off() ...
2022-05-30ARM: configs: Enable more audio support for i.MXMark Brown1-0/+2
The generic audio card for Freescale platforms is used by a wide range of i.MX systems and also has selects for the various audio controllers used on them so will help with systems that don't use that specific card too. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20220513121258.168364-1-broonie@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-30Merge tag 'socfpga_dts_updates_for_v5.19' of ↵Arnd Bergmann4-5/+5
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/late SoCFPGA dts updates for v5.19 - dtschema fix SPI NOR node - correct dt-bindings doc for Altera gpio driver - add support for n6000 Agilex platform and dt-bindings documentation * tag 'socfpga_dts_updates_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: intel: add device tree for n6000 dt-bindings: intel: add binding for Intel n6000 dt-bindings: soc: add bindings for Intel HPS Copy Engine dt-bindings: gpio: altera: correct interrupt-cells ARM: dts: socfpga: align SPI NOR node name with dtschema Link: https://lore.kernel.org/r/20220519232317.16079-1-dinguyen@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-30Merge tag 'aspeed-5.19-devicetree' of ↵Arnd Bergmann9-55/+431
git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/late ASPEED device tree updates for 5.19 - New machine: * Nuvia's DC-SCM BMC - Enable AST2600 GFX, the BMC-driven graphics device - Add a bunch of devices for the AST2600 EVB - Updates to the AST2600 Bletchley machine - Backwards compatible changes to support the new spi-mem based SPI NOR driver * tag 'aspeed-5.19-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc: ARM: dts: aspeed: ast2600-evb: Enable GFX device ARM: dts: aspeed: Add GFX node to AST2600 ARM: dts: aspeed: ast2600-evb: Enable virtual hub ARM: dts: aspeed: ast2600-evb: Enable video engine ARM: dts: aspeed: everest, rainier: Add power-ffs-sync-history GPIO ARM: dts: aspeed: Add Nuvia DC-SCM BMC ARM: dts: aspeed: bletchley: add sample averaging for ADM1278 ARM: dts: aspeed: bletchley: add eeprom node on each sled ARM: dts: aspeed: bletchley: add pca9536 node on each sled ARM: dts: aspeed: bletchley: update gpio0 line names ARM: dts: aspeed: bletchley: Enable mdio0 bus ARM: dts: aspeed: bletchley: switch spi2 driver to aspeed-smc ARM: dts: aspeed: bletchley: enable ehci0 device node ARM: dts: aspeed: Add USB2.0 device controller node ARM: dts: aspeed-g4: Set spi-max-frequency for all flashes ARM: dts: aspeed: Enable Dual SPI RX transfers ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllers ARM: dts: aspeed: ast2600-evb: Enable RX delay for MAC0/MAC1 Link: https://lore.kernel.org/r/CACPK8XfUmFxU8Y6C+aZ2+=dT7=fCfs2=2_aYqyRjoXCoeQaUWQ@mail.gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-29Merge tag 'trace-v5.19' of ↵Linus Torvalds1-4/+2
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing updates from Steven Rostedt: "The majority of the changes are for fixes and clean ups. Notable changes: - Rework trace event triggers code to be easier to interact with. - Support for embedding bootconfig with the kernel (as suppose to having it embedded in initram). This is useful for embedded boards without initram disks. - Speed up boot by parallelizing the creation of tracefs files. - Allow absolute ring buffer timestamps handle timestamps that use more than 59 bits. - Added new tracing clock "TAI" (International Atomic Time) - Have weak functions show up in available_filter_function list as: __ftrace_invalid_address___<invalid-offset> instead of using the name of the function before it" * tag 'trace-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (52 commits) ftrace: Add FTRACE_MCOUNT_MAX_OFFSET to avoid adding weak function tracing: Fix comments for event_trigger_separate_filter() x86/traceponit: Fix comment about irq vector tracepoints x86,tracing: Remove unused headers ftrace: Clean up hash direct_functions on register failures tracing: Fix comments of create_filter() tracing: Disable kcov on trace_preemptirq.c tracing: Initialize integer variable to prevent garbage return value ftrace: Fix typo in comment ftrace: Remove return value of ftrace_arch_modify_*() tracing: Cleanup code by removing init "char *name" tracing: Change "char *" string form to "char []" tracing/timerlat: Do not wakeup the thread if the trace stops at the IRQ tracing/timerlat: Print stacktrace in the IRQ handler if needed tracing/timerlat: Notify IRQ new max latency only if stop tracing is set kprobes: Fix build errors with CONFIG_KRETPROBES=n tracing: Fix return value of trace_pid_write() tracing: Fix potential double free in create_var_ref() tracing: Use strim() to remove whitespace instead of doing it manually ftrace: Deal with error return code of the ftrace_process_locs() function ...
2022-05-27Merge tag 'v5.19-rockchip-dts32-2' of ↵Arnd Bergmann6-20/+23
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/late Amba and clock fixes to conform better to actual dt-bindings. * tag 'v5.19-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: add clocks property to cru node rk3228 ARM: dts: rockchip: add clocks property to cru node rk3036 ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188 ARM: dts: rockchip: add clocks property to cru node rk3288 ARM: dts: rockchip: Remove "amba" bus nodes from rv1108 ARM: dts: rockchip: add clocks property to cru node rv1108 Link: https://lore.kernel.org/r/4798587.jE0xQCEvom@phil Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27Merge tag 'mm-nonmm-stable-2022-05-26' of ↵Linus Torvalds1-23/+4
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm Pull misc updates from Andrew Morton: "The non-MM patch queue for this merge window. Not a lot of material this cycle. Many singleton patches against various subsystems. Most notably some maintenance work in ocfs2 and initramfs" * tag 'mm-nonmm-stable-2022-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (65 commits) kcov: update pos before writing pc in trace function ocfs2: dlmfs: fix error handling of user_dlm_destroy_lock ocfs2: dlmfs: don't clear USER_LOCK_ATTACHED when destroying lock fs/ntfs: remove redundant variable idx fat: remove time truncations in vfat_create/vfat_mkdir fat: report creation time in statx fat: ignore ctime updates, and keep ctime identical to mtime in memory fat: split fat_truncate_time() into separate functions MAINTAINERS: add Muchun as a memcg reviewer proc/sysctl: make protected_* world readable ia64: mca: drop redundant spinlock initialization tty: fix deadlock caused by calling printk() under tty_port->lock relay: remove redundant assignment to pointer buf fs/ntfs3: validate BOOT sectors_per_clusters lib/string_helpers: fix not adding strarray to device's resource list kernel/crash_core.c: remove redundant check of ck_cmdline ELF, uapi: fixup ELF_ST_TYPE definition ipc/mqueue: use get_tree_nodev() in mqueue_get_tree() ipc: update semtimedop() to use hrtimer ipc/sem: remove redundant assignments ...
2022-05-27ARM: dts: rockchip: add clocks property to cru node rk3228Johan Jonker1-0/+2
Add clocks and clock-names to the rk3228 cru node, because the device has to have at least one input clock. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220330121923.24240-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: rockchip: add clocks property to cru node rk3036Johan Jonker1-0/+2
Add clocks and clock-names to the rk3036 cru node, because the device has to have at least one input clock. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220330114847.18633-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188Johan Jonker2-2/+4
Add clocks property to rk3066a/rk3188 cru node to fix warnings like: 'clocks' is a dependency of 'assigned-clocks' Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220329111323.3569-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: rockchip: add clocks property to cru node rk3288Johan Jonker1-0/+2
Add clocks property to rk3288 cru node to fix warnings like: 'clocks' is a dependency of 'assigned-clocks'. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220329113657.4567-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: rockchip: Remove "amba" bus nodes from rv1108Johan Jonker1-18/+11
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful purpose, and certainly bear no relation at all to the actual underlying interconnect topology. They appear to be cargo-cult copying from a design misstep in the very early days of FDT adoption on ARM, which was righted with the "arm,primecell" compatible, and the last trace of the idea finally purged by commit 2ef7d5f342c1 ("ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus""). As such, they can simply be removed and the DMA-330 nodes fitted into the normal sort order. The node names should be generic, so rename it to "dma-controller". Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220330131608.30040-3-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: rockchip: add clocks property to cru node rv1108Johan Jonker1-0/+2
Add clocks and clock-names to the rv1108 cru node, because the device has to have at least one input clock. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20220330131608.30040-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2022-05-27ARM: dts: da850: use new 'dma-channels' propertyKrzysztof Kozlowski1-0/+2
The '#dma-channels' property was deprecated in favor of one defined by generic dma-common DT bindings. Add new property while keeping old one for backwards compatibility. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220516142857.6419-3-krzysztof.kozlowski@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27ARM: dts: pxa: use new 'dma-channels/requests' propertiesKrzysztof Kozlowski4-3/+14
The '#dma-channels' and '#dma-requests' properties were deprecated in favor of these defined by generic dma-common DT bindings. Add new properties while keeping old ones for backwards compatibility. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220516142857.6419-2-krzysztof.kozlowski@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27ARM: ep93xx: Make ts72xx_register_flash() staticAlexander Sverdlin1-1/+1
... and fix the warning/error: arch/arm/mach-ep93xx/ts72xx.c:154:13: error: no previous prototype for function 'ts72xx_register_flash' [-Werror,-Wmissing-prototypes] void __init ts72xx_register_flash(struct mtd_partition *parts, int n, ^ arch/arm/mach-ep93xx/ts72xx.c:154:1: note: declare 'static' if the function is not intended to be used outside of this translation unit void __init ts72xx_register_flash(struct mtd_partition *parts, int n, ^ static Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Link: https://lore.kernel.org/lkml/202202140141.HRZ3WZwi-lkp@intel.com/T/ Link: https://lore.kernel.org/r/20220523065616.325052-1-alexander.sverdlin@gmail.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27ARM: configs: enable support for Kontron KSwitch D10Michael Walle1-0/+11
The Kontron KSwitch D10 is based on a Microchip LAN9668 SoC. It is a managed ethernet network switch with either 8 copper ports or 6 copper ports and 2 SFP cages. Enable all required kconfig symbols, either as module where possible or compiled-in where it is not possible. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20220518141542.531148-1-michael@walle.cc' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27Merge tag 'at91-dt-5.19-2' of ↵Arnd Bergmann6-3/+58
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/late AT91 DT #2 for 5.19: - at91: more DT compliance updates for RTC and RTT nodes - at91: sama7g5: add microphone support * tag 'at91-dt-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: dts: at91: sama7g5ek: add node for PDMC0 ARM: dts: at91: sama7g5: add nodes for PDMC ARM: dts: at91: Use the generic "rtc" node name for the rtt IPs ARM: dts: at91: Add the required 'atmel, rtt-rtc-time-reg' property Link: https://lore.kernel.org/r/20220517153252.92393-1-nicolas.ferre@microchip.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27Merge tag 'at91-soc-5.19-2' of ↵Arnd Bergmann1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/late AT91 SoC #2 for 5.19: - One Kconfig fix for random build error * tag 'at91-soc-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: at91: pm: Fix rand build error Link: https://lore.kernel.org/r/20220517150832.89451-1-nicolas.ferre@microchip.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27ep93xx: clock: Do not return the address of the freed memoryGenjian Zhang1-4/+6
Avoid return freed memory addresses,Modified to the actual error return value of clk_register(). Fixes: 9645ccc7bd7a ("ep93xx: clock: convert in-place to COMMON_CLK") Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn> Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-27Merge branch 'hpe/gxp-soc' into arm/lateArnd Bergmann9-0/+201
Patch series from Nick Hawkins: "The GXP is the HPE BMC SoC that is used in the majority of HPE current generation servers. Traditionally the asic will last multiple generations of server before being replaced. Info about SoC: HPE GXP is the name of the HPE Soc. This SoC is used to implement many BMC features at HPE. It supports ARMv7 architecture based on the Cortex A9 core. It is capable of using an AXI bus to which a memory controller is attached. It has multiple SPI interfaces to connect boot flash and BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It has multiple i2c engines to drive connectivity with a host infrastructure. The initial patches enable the watchdog and timer enabling the host to be able to boot." * hpe/gxp-soc: MAINTAINERS: Introduce HPE GXP Architecture ARM: dts: Introduce HPE GXP Device tree dt-bindings: arm: hpe: add GXP Support dt-bindings: timer: hpe,gxp-timer: Add HPE GXP Timer and Watchdog clocksource/drivers/timer-gxp: Add HPE GXP Timer watchdog: hpe-wdt: Introduce HPE GXP Watchdog ARM: configs: multi_v7_defconfig: Add HPE GXP ARCH ARM: hpe: Introduce the HPE GXP architecture Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-26ftrace: Remove return value of ftrace_arch_modify_*()Li kunyu1-4/+2
All instances of the function ftrace_arch_modify_prepare() and ftrace_arch_modify_post_process() return zero. There's no point in checking their return value. Just have them be void functions. Link: https://lkml.kernel.org/r/20220518023639.4065-1-kunyu@nfschina.com Signed-off-by: Li kunyu <kunyu@nfschina.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2022-05-26Merge tag 'gpio-updates-for-v5.19' of ↵Linus Torvalds3-11/+5
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio updates from Bartosz Golaszewski: "We have lots of small changes all over the place, but no huge reworks or new drivers: - use ioread()/iowrite() interfaces instead of raw inb()/outb() in drivers - make irqchips immutable due to the new warning popping up when drivers try to modify the irqchip structures - add new compatibles to dt-bindings for realtek-otto, renesas-rcar and pca95xx - add support for new models to gpio-rcar, gpio-pca953x & gpio-realtek-otto - allow parsing of GPIO hogs represented as children nodes of gpio-uniphier - define a set of common GPIO consumer strings in dt-bindings - shrink code in gpio-ml-ioh by using more devres interfaces - pass arguments to devm_kcalloc() in correct order in gpio-sim - add new helpers for iterating over GPIO firmware nodes and descriptors to gpiolib core and use it in several drivers - drop unused syscon_regmap_lookup_by_compatible() function - correct format specifiers and signedness of variables in GPIO ACPI - drop unneeded error checks in gpio-ftgpio - stop using the deprecated of_gpio.h header in gpio-zevio - drop platform_data support in gpio-max732x - simplify Kconfig dependencies in gpio-vf610 - use raw spinlocks where needed to make PREEMPT_RT happy - fix return values in board files using gpio-pcf857x - convert more drivers to using fwnode instead of of_node - minor fixes and improvements in gpiolib core" * tag 'gpio-updates-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (55 commits) gpio: sifive: Make the irqchip immutable gpio: rcar: Make the irqchip immutable gpio: pcf857x: Make the irqchip immutable gpio: pca953x: Make the irqchip immutable gpio: dwapb: Make the irqchip immutable gpio: sim: Use correct order for the parameters of devm_kcalloc() gpio: ml-ioh: Convert to use managed functions pcim* and devm_* gpio: ftgpio: Remove unneeded ERROR check before clk_disable_unprepare gpio: ws16c48: Utilize iomap interface gpio: gpio-mm: Utilize iomap interface gpio: 104-idio-16: Utilize iomap interface gpio: 104-idi-48: Utilize iomap interface gpio: 104-dio-48e: Utilize iomap interface gpio: zevio: drop of_gpio.h header gpio: max77620: Make the irqchip immutable dt-bindings: gpio: pca95xx: add entry for pca6408 gpio: pca953xx: Add support for pca6408 gpio: max732x: Drop unused support for irq and setup code via platform data gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610 gpio: syscon: Remove usage of syscon_regmap_lookup_by_compatible ...
2022-05-26Merge tag 'kbuild-v5.19' of ↵Linus Torvalds2-23/+2
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild updates from Masahiro Yamada: - Add HOSTPKG_CONFIG env variable to allow users to override pkg-config - Support W=e as a shorthand for KCFLAGS=-Werror - Fix CONFIG_IKHEADERS build to support toybox cpio - Add scripts/dummy-tools/pahole to ease distro packagers' life - Suppress false-positive warnings from checksyscalls.sh for W=2 build - Factor out the common code of arch/*/boot/install.sh into scripts/install.sh - Support 'kernel-install' tool in scripts/prune-kernel - Refactor module-versioning to link the symbol versions at the final link of vmlinux and modules - Remove CONFIG_MODULE_REL_CRCS because module-versioning now works in an arch-agnostic way - Refactor modpost, Makefiles * tag 'kbuild-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (56 commits) genksyms: adjust the output format to modpost kbuild: stop merging *.symversions kbuild: link symbol CRCs at final link, removing CONFIG_MODULE_REL_CRCS modpost: extract symbol versions from *.cmd files modpost: add sym_find_with_module() helper modpost: change the license of EXPORT_SYMBOL to bool type modpost: remove left-over cross_compile declaration kbuild: record symbol versions in *.cmd files kbuild: generate a list of objects in vmlinux modpost: move *.mod.c generation to write_mod_c_files() modpost: merge add_{intree_flag,retpoline,staging_flag} to add_header scripts/prune-kernel: Use kernel-install if available kbuild: factor out the common installation code into scripts/install.sh modpost: split new_symbol() to symbol allocation and hash table addition modpost: make sym_add_exported() always allocate a new symbol modpost: make multiple export error modpost: dump Module.symvers in the same order of modules.order modpost: traverse the namespace_list in order modpost: use doubly linked list for dump_lists modpost: traverse unresolved symbols in order ...
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-24 19:23:59 +0000